Use and Care Guide
®
Combo Model:
CO29FF
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Table of Contents
Introduction ...............................................................................................................................2
Warranty Registration .......................................................................................................2
Please Record Your Model Information ...........................................................................2
Table of Contents .......................................................................................................................3
Safety Precautions ......................................................................................................................5
Safety Alert Definitions .....................................................................................................5
General Precautions ...........................................................................................................5
Product Features ........................................................................................................................6
Origins Ice Maker/Refrigerator Model CO29FF ................................................................6
Operation ...................................................................................................................................6
Initial Startup .....................................................................................................................6
Temperature Control .........................................................................................................7
Ice Maker ............................................................................................................................7
Normal Operating Sounds .................................................................................................8
Outdoor, Marine and RV Usage ........................................................................................8
Storage, Vacation, Moving ................................................................................................8
Product Disposal .................................................................................................................9
Cleaning and Maintenance .......................................................................................................9
General Cleaning ...............................................................................................................9
Maintenance ......................................................................................................................9
Service .......................................................................................................................................14
Before Calling for Service ................................................................................................14
If Service is Required ........................................................................................................14
Replacement Parts ...........................................................................................................14
Troubleshooting Guide ....................................................................................................15
U-Line Corporation Limited Warranty ....................................................................................19
CO29FF
3
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
4
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
3 Safety Precautions
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform
maintenance on the unit until the electricity
has been disconnected.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Altering, cutting of power cord, removal of
power cord, removal of power plug, or direct
wiring can cause serious injury, fire and/or loss
of property and/or life, and will void the
warranty.
IMPORTANT
PLEASE READ all instructions completely before
attempting to install, operate, or service your unit.
• Proper installation procedures must be followed
if this unit is being initially installed, or is moved
to a new location after being in service. An
INSTALLATION GUIDE for your unit, providing
complete installation information is available
from U-Line Corporation directly, and must be
consulted before any installation is begun. U-Line
contact information appears on the rear cover of
this guide.
• Never use an extension cord to connect power
to the unit.
• Always keep your working area dry.
• This unit requires connection to a grounded
(three-prong), polarized receptacle that has been
placed by a qualified electrician in accordance
with applicable electrical codes.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp
edges.
• If your model requires defrosting, DO NOT use any
type of heater to defrost. Using a heater to speed
up defrosting can cause personal injury and
damage to the inner lining.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
IMPORTANT
• Do not lift unit by door handle.
• Never install or operate the unit behind closed
doors. Be sure front grille is free of obstruction.
Obstructing free air flow can cause the unit to
malfunction and may void the warranty.
• Failure to clean the condenser every three months
can cause the unit to malfunction. This could void
the warranty.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
CAUTION
• Allow unit temperature to stabilize for 24 hours
before use.
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
• If your model requires defrosting, never use an
ice pick or other sharp instrument to help speed
up defrosting. These instruments can puncture
the inner lining or damage the cooling unit.
• Use only genuine U-Line replacement parts.
Imitation parts can damage the unit, affect its
operation or performance and may void the
warranty.
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away
your old refrigerator or freezer, take off the doors
and leave shelves in place so that children may not
easily climb inside.
CO29FF
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Product Features
5 Operation
Origins Ice Maker/Refrigerator
Model CO29FF
The CO29FF Ice Maker/Refrigerator with adjustable
temperature control provides 2.1 cubic feet (59 L) of
refrigeration in one compact unit.
ULIN_0130_A
• The ice maker produces up to 8 lbs (3.6 kg) of ice per
day, and will store 13 lbs (5.9 kg). It conserves on water,
using only 2-3/4 gallons (12.5 L) to produce
approximately 22 lbs (10 kg) of ice.
Figure 2
IMPORTANT
• Frost Free technology
Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
• Two tempered glass shelves provide a generous
amount of shelving space. The shelves are easy to
clean.
• Two in-door shelves feature clear bottle retainers, and
an additional half shelf is provided to maximize
storage capacity.
Initial Startup
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
• The door features an integrated handle, and can
accommodate a custom 1/4" (0.64 cm) flat or raised
panel to match surrounding cabinets.
IMPORTANT
• The door is field-reversible.
• U-Line recommends the unit be allowed to run
overnight prior to loading the refrigerator and/or
freezer with product.
• On ice maker equipped units, it is possible that
dirt or scale will dislodge in the water line.
Always throw away all ice cubes made during the
first two to three hours of operation.
• The unit features a vinyl clad steel cabinet that
provides a rich textured look, and resists scratching,
peeling, and flaking.
Features and specifications are subject to change without
notice.
ULIN_0129_A
Figure 3
To turn the unit on or off, press the rocker switch (Figure
3) located below the temperature control dial in the
center of the grille.
6
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Control
Ice Maker
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
to cool and maintain the cube supply. Frost-free icemaker
units have lower ice production than manual defrost
units.
Checking Product Temperature
IMPORTANT
Do not place cans or bottles in the ice compartment
because they will freeze.
ULIN_0093_A
Figure 4
To check the actual product temperature, in refrigerator
section only, insert an accurate thermometer into a plastic
(non-breakable) bottle that is partially filled with water.
Tighten the bottle cap securely (Figure 4).
ULIN_0087_A
Figure 6
Ice production may be interrupted by raising the bin arm
into an upright and locked position (Figure 6). The unit
will maintain temperature for ice storage.
Place the bottle in the refrigerator area for 24 hours.
Refrain from opening the unit during the testing period.
After 24 hours, check the temperature of the water. If
required, adjust the temperature control in a small
increment (See ADJUSTING TEMPERATURE).
IMPORTANT
If you are not intending to use the ice maker and
turn the supply valve off, it is imperative to raise
the bin arm of the ice maker (Figure 6). Failure to
raise the bin arm may result in damage to the water
valve.
Factors which affect the internal temperatures of the
cabinet include:
• Temperature setting.
• Ambient temperature where installed.
Certain sounds are normal during the unit’s operation.
You may hear the compressor or fan motor, the water
valve, or ice dropping into the ice bucket.
• Number of times and length of time the door is
opened and closed.
• Installation in direct sunlight or near a heat source.
WARNING
Adjusting Temperature
NEVER use an ice pick, knife or other sharp
instrument to separate cubes. Shake the ice
bucket instead.
1
During periods of limited usage or high ambient
temperatures, it is common for cubes to fuse together.
Shake the bucket to break apart cubes. If the ice maker is
not used regularly, the ice bucket should be emptied
periodically to ensure fresh cubes.
ULIN_0014_A
It is normal for cubes to appear cloudy. This is caused by
air being trapped in the water due to fast freezing. It has
nothing to do with the health, taste or chemical make-up
of the water. It is the same air that is in every glass of
water you drink.
Figure 5
Adjust the temperature by turning the numbered dial
(Figure 5, 1) in small increments.
CO29FF
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The ice bucket can be removed for emptying and
cleaning. To remove the ice bucket, raise the bin arm and
remove the bucket from the ice compartment. Use the ice
bucket for ice storage only.
Storage, Vacation, Moving
If the unit will not be used for an extended period, or
otherwise stored, follow these steps completely:
WARNING
Normal Operating Sounds
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. In spite of
this technology, your model may make sounds that are
unfamiliar.
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels.
Failure to do so may result in death or electrical
shock.
1. Remove all consumable contents from the unit.
2. Disconnect power to the unit.
Normal operating sounds may be more noticeable
because of the unit’s environment. Hard surfaces such as
cabinets, wood/vinyl/tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
3. Shut off water supply to the unit at the main water
source.
Common refrigeration components, and a brief
description of the normal operating sounds they make,
are listed below. NOTE: Your product may not contain all
of the components listed.
IMPORTANT
• If the ambient temperature is expected to drop
below 45°F, turn off and unplug unit, and drain all
water from the unit to prevent freezing damage
not covered by the warranty.
• The use of anti-freeze or other products of this
nature is not necessary and is not recommended.
•
•
•
•
Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
4. Disconnect the water valve inlet and outlet lines, and
allow them to drain completely.
Condenser Fan: Air moving through a condenser may be
heard.
5. Reconnect power to the unit, and allow it to run for
one hour (minimum) until any remaining ice has been
ejected from the ice maker assembly.
Automatic Defrost/Drain Pan: Water may be heard
dripping or running into the drain pan when the unit is in
the defrost cycle.
6. Disconnect power to the unit, dry any remaining water
from the ice maker assembly, and reconnect any lines
removed from the water supply valve.
Outdoor, Marine and RV Usage
Some U-Line models are designed to operate in outdoor,
marine and RV environments. For best performance, keep
the unit out of direct sunlight.
7. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
• If the unit will be shut off for five days or more, prop
door open to allow for air circulation and prevent mold
and mildew.
8. Clean and dry the interior of the cabinet (See CLEANING
AND MAINTENANCE: GENERAL CLEANING).
9. During periods of non-use, the cabinet must remain
open to prevent the formation of mold and mildew.
Open door a minimum of 2" (5 cm) to provide the
necessary ventilation.
IMPORTANT
If the ambient temperature is expected to drop
below 45°F, turn off and unplug unit, and drain all
water from the unit to prevent freezing damage not
covered by the warranty.
• High ambient temperatures (110°F or higher) may
reduce the unit's ability to reach low temperatures.
8
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Disposal
6 Cleaning and Maintenance
General Cleaning
If the unit is being removed from service for disposal,
check and obey all Federal, State and/or Local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
Exterior Cleaning (As Required)
1. Disconnect power to the unit and unplug the power
cord from its outlet.
Black and White Models:
• Surfaces may be cleaned with a mild detergent and
warm water solution. Do not use solvent-based or
abrasive cleaners. Use a soft sponge and rinse with
clean water. Wipe with a soft, clean towel to prevent
water spotting.
2. Shut off water supply to the unit at the main water
source and disconnect the supply line to the unit’s water
valve.
DANGER
Interior Cleaning (As Required)
RISK OF CHILD ENTRAPEMENT. Before you throw
away your old refrigerator or freezer, take off the
doors and leave shelves in place so that children
may not easily climb inside.
• Turn unit off. Clean the interior and all removed
components using a mild non-abrasive detergent and
warm water solution applied with a soft sponge or
non-abrasive cloth. Rinse the interior using a soft
sponge and clean water.
3. Remove the cabinet door if equipped and secure all
interior shelves to the interior of the cabinet using a
heavy duty cloth or package sealing tape.
• Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transmit
taste to the interior products and damage or
discolor the interior.
Maintenance
Proper maintenance of your U-Line product will ensure
efficiency, top performance and long life. The
maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if you
have pets or other special considerations.
Defrosting
Frost-Free Models
Frost-free models do not produce frost in normal
operating conditions.
WARNING
DO NOT use any type of electrical heating device,
ice pick, knife or other sharp instrument to
defrost; this could damage the inner lining or
refrigeration system and void the warranty.
CO29FF
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Condenser Cleaning
Interval - Every Three Months
To maintain operational efficiency, keep the front grille
free of dust and lint, and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
WARNING
2
1
Disconnect electric power to the unit before
cleaning the condenser.
ULIN_0198_A
Figure 9
WARNING
6. Make sure grille cap is behind grille in slots provided in
grille (Figure 9, 1) before attaching grille to unit, and
secure but do not overtighten both grille screws
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
(Figure 9, 2)
.
7. Reinstall the control knob (Figure 7, 1)
.
IMPORTANT
DO NOT use any type of cleaner on the condenser
unit.
8. Reconnect power to the unit.
Ice Maker Maintenance
Inlet Screen
1. Disconnect power to the unit.
Interval - Every Twelve Months
The solenoid valve inlet screen must be cleaned at least
2
once each year as follows:
1. Shut off the water at the main supply valve.
2. Pull the unit out to access the back panel.
3. Disconnect electrical power to the unit.
1
ULIN_0197_A
2
Figure 7
2. Remove the control knob (Figure 7, 1) by pulling it
straight out, away from grille.
3. Remove two screws from grille (Figure 7, 2) and save.
4. Remove grille and grille cap from unit.
1
1
ULIN_0054_A
Figure 10
4. Disconnect the hose connector (Figure 10, 1) from the
water solenoid valve (Figure 10, 2)
.
ULIN_0153_A
5. DO NOT remove the inlet screen from the water
solenoid valve. Use a tooth brush to gently clean any
sediment from the inlet screen.
Figure 8
5. Clean the condenser coil (Figure 8, 1) using a using a
soft brush with a “combing” action or vacuum cleaner.
Do not touch the condenser coil.
6. Re-connect the water supply hose connector (Figure
10, 1) to the water solenoid valve (Figure 10, 2)
.
Tighten the connector securely.
7. Open the water main supply valve and check for
leakage at the water hose connection. Ensure that the
water supply line is not kinked.
8. Reconnect power to the unit before re-installing.
10
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice Cube Thickness Adjustment
4. Install the ice maker assembly cover.
Interval - As Required
IMPORTANT
On ice maker equipped models, the cube size may be
adjusted by changing the amount of water injected into
the ice maker assembly as follows:
Use only genuine U-Line replacement parts. U-Line
ice maker parts are not the same as standard FSP
Whirlpool parts. Using non U-Line parts can reduce
ice rate, cause water to overflow from ice maker
mold, damage the unit, and may void the warranty.
Leveling
It is important that this unit is set level, for proper door
and ice maker operation.
ULIN_0273_A
Figure 11
1. Remove the ice maker assembly cover (Figure 11).
ULIN_0211_A
Figure 13
Use a level to check the levelness of the unit from front to
back and from side to side. Level should be placed along
top edge and side edge as shown (Figure 13).
NOTE: This model DOES NOT have leveling feet. This
model MUST be placed on a level surface to operate
properly.
ULIN_0056_A
Figure 12
2. Locate the adjusting screw on the ice maker assembly
control box. The adjusting screw is just below the minus
(-) and plus (+) signs on the control box (Figure 12)
.
NOTE: Make adjustments in small increments. Too
large of an adjustment could cause the unit to
malfunction.
CAUTION
Too large of an adjustment to the screw can cause
the water to overflow the ice maker and can cause
property damage.
3. Turn the adjusting screw toward the minus (-) sign
(clockwise) for smaller cubes or toward the plus (+) sign
(counterclockwise) for larger cubes.
CO29FF
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove two grille screws, and remove the grille.
Door Alignment Check and Adjustment
IMPORTANT
Properly aligned, the door’s gasket should be firmly
in contact with the cabinet all the way around the
door (no gaps). Carefully examine the door’s gasket
to assure that it is firmly in contact with the
cabinet. Also make sure the door gasket is not
pinched on the hinge side of the door.
ULIN_0210_A
Figure 16
1. Remove top hinge from cabinet (three screws) (Figure
16). Hold door to keep it from falling.
2. Lift the door off the bottom hinge.
ULIN_0210_A
Figure 14
1. Loosen (do not remove) top (Figure 14) and bottom
hinge screws.
2. Align door squarely with cabinet.
3. Make sure gasket is firmly in contact with cabinet all
the way around the door (no gaps).
4. Tighten bottom hinge screws.
5. Tighten top hinge screws.
ULIN_0215_A
Figure 17
Door Reversal
Depending upon the location of the unit, it may be
desirable to change the side on which the door is
mounted. NOTE: On built-in installations, changing the
door mounting to the left side may interfere with ice
bucket removal.
3. Remove bottom hinge from cabinet (two screws)
(Figure 17)
.
To reverse the door mounting, perform the following:
1
ULINE_0216_A
ULIN_0014_A
Figure 18
Figure 15
4. Remove screws on opposite side of cabinet (Figure 18)
Note that there may be a nut behind one or both
screws on either side.
.
1. Remove the control knob (Figure 15, 1) by pulling it
away from the cabinet.
12
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
ULINE_0217_A
ULIN_0144_A
Figure 19
Figure 22
5. Install hinge on opposite side, bottom of cabinet
(Figure 19). Replace nut on back side where installed.
Align hinge outer edge with cabinet before tightening
screws.
9. Remove three plastic screw plugs in hinge holes, top of
cabinet, opposite side; being careful not to scratch
cabinet (Figure 22)
.
10. Place door on lower hinge pin. Invert and install upper
hinge on door.
1
ULIN_0109_A
Figure 20
ULIN_0145_A
6. Relocate plastic spacer/bushing (Figure 20, 1) on
bottom of door to opposite side, and place door on
bottom hinge pin. Clean out bushing hole in door
bottom with a screwdriver if needed.
Figure 23
11. Fasten upper hinge to unit (three screws) (Figure 23)
.
Partially tighten screws until door is aligned.
12. Adjust door to assure proper seal. Tighten upper hinge
screws securely.
Hinge
13. Replace three plastic plugs removed in Step 10 into
holes on top of unit. Replace screws in holes in bottom
of unit, opposite side.
Plastic
Plug Hole
Plastic
Plug Hole
14. Re-inspect door seal and alignment. Adjust if needed.
Screw
Right Side
Door Swing
Left Side
Door Swing
Right Side
Hinge
Invert
Screw
Invert
Hinge
ULIN_0142_A
Figure 21
7. Remove plastic hole plug from door handle and
relocate on opposite side (Figure 21)
.
2
8. Remove pivot screw from top hinge, invert screw and
1
ULIN_0214_A
reinstall pivot screw in top hinge (Figure 21)
.
Figure 24
CO29FF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Make sure grille cap is behind grille in slots provided in
grille (Figure 24, 1) before attaching grille to unit, and
secure but do not overtighten both grille screws
7 Service
(Figure 24, 2)
.
Before Calling for Service
16. Install the temperature control knob.
Glass Shelf Removal/Installation
Remove the shelves as follows:
If your U-Line product appears to be malfunctioning, read
through the OPERATION section of this guide to ensure
that the function of all controls are clearly understood. If
the malfunction persists, the TROUBLESHOOTING GUIDE
in this guide will assist you in quickly identifying common
problems, and provide information on possible causes and
remedies. Most often, this will resolve the problem
without the need to call for service.
If Service is Required
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
1
You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
ULINE_0277_A
Figure 25
1. Open door completely.
Replacement Parts
2. Grasp the shelf edge in the center (Figure 25, 1) and
When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
slide the shelf from the unit.
3. Reposition the shelf as required, ensuring the raised
white edge strip is toward the rear of the unit and the
decorative graphics, if applied, are on the underside of
the shelves.
durability of your product, and may also void its warranty.
IMPORTANT
Make sure the shelves are inserted fully into the
unit.
14
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
DANGER
ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
Troubleshooting - What to check when problems occur:
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit not cold enough
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST,
REVERSE).
Item(s) interfering with door
Dirty condenser coils
Reposition or remove item(s).
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Airflow to front grille blocked
Airflow must not be obstructed to front grille (See
OPERATION).
Temperature not set cold enough
Set control knob to cooler setting (See OPERATION).
Allow 24 hours for temperature to stabilize.
Water is leaking out the back of the Water supply connection leaking
unit.
Tighten fitting as required.
Ice cubes sticking together
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST,
REVERSE).
Infrequent use of cubes
Break apart cubes.
Noise during operation
Copper water supply tubing
contacting internal components
Carefully bend tubing away from cabinet and
components.
Certain sounds are normal.
Soft sounds from the fan and water/dropping sounds
from the ice maker will be heard.
No ice
Bin arm locked in upright position
No water to unit
Lower bin arm.
Turn on water or contact plumber.
Not enough ice
Ice cube size too large
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUST).
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Water leaks into ice bucket.
Water level set too high
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUST).
Fresh food section on Combo units
too cold
Ice bucket not fully inserted
Push ice bucket into place.
Freezer door not closed correctly
Temperature control set too cold
Be sure freezer door is closed correctly.
Set control to warmer setting (See OPERATION).
Unit too cold
CO29FF
15
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
16
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
CO29FF
17
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
18
CO29FF
Download from Www.Somanuals.com. All Manuals Search And Download.
U-Line Corporation Limited Warranty
U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of
one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the
evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from
defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year
warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a
product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the
United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with
the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-
Line shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and
Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall
cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other
charges, including transportation charges for replacements under this warranty and labor costs not specifically covered
by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product.
The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you
The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God,
such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation,
unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the
controls; door reversal; or cleaning the condenser.
If a product defect is discovered during the applicable warranty period, you must promptly notify either the dealer from
whom you purchased the product or U-Line at P.O. Box 245040, Milwaukee, Wisconsin 53224 or at 414-354-0300. In no
event shall such notification be received later than 30 days after the expiration of the applicable warranty period. U-Line
may require that defective parts be returned, at your expense, to U-Lines factory in Milwaukee, Wisconsin, for
inspection. Any action by you for breach of warranty must be commenced within one year after the expiration of the
applicable warranty period.
This limited warranty is in lieu of any other warranty, express or implied, including, but not limited to any
implied warranty of merchantability or fitness for a particular purpose; provided however, that to the
extent required by law, implied warranties are included but do not extend beyond the duration of the
express warranty first set forth above. U-Lines sole liability and your exclusive remedy under this warranty
is set forth in the initial paragraph above. U-Line shall have no liability whatsoever for any incidental,
consequential or special damages arising from the sale, use or installation of the product or from any other
cause whatsoever, whether based on warranty (express or implied) or otherwise based on contract, tort or
any other theory of liability.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
CO29FF
19
Download from Www.Somanuals.com. All Manuals Search And Download.
For General Inquiries:
P.O. Box 245040
Milwaukee, Wisconsin
53224-9540 U.S.A.
Phone (800) 779-2547
FAX (414) 354-5696
For Service and Parts
Assistance:
Phone (800) 779-2547
(414) 354-0300
FAX (414) 354-5696
Email:
E-mail:
For more than four decades, U-Line has distinguished itself as the
leader in built-in under-counter ice making, refrigeration and
wine storage appliances.
An INSTALLATION MANUAL for your unit, providing complete
installation information, is available for download at
including panel size, and instructions are available by visiting
When you need replacement parts, always request genuine U-Line
distributor in your area.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
®
®
undercounter ice makers, Combo ice maker/refrigerators, Wine Captain wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2006 U-Line Corporation
Publication No. 30099
01/2006 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|