• W A R N I N G •
This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
Instruction
Manual
Software Version 2.5U
Download from Www.Somanuals.com. All Manuals Search And Download.
About Your Security System
Your DSC security equipment has been designed to provide you with the greatest possible flexibility and
convenience. Read this manual carefully and have your installer instruct you on your system's operation
and on which features have been implemented in your system. All users of this system should be equally
instructed in its use. Fill out the “System Information” page with all of your zone information and access
codes and store this manual in a safe place for future reference.
Fire Detection
This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a
warning if a fire condition is detected. Good fire detection depends on having adequate number of
detectors placed in appropriate locations. This equipment should be installed in accordance with your local
fire laws and recommendations. Carefully review the Family Escape Planning guidelines in this manual.
NOTE: Your installer must enable the fire detection portion of this equipment before it becomes
functional.
Testing
To insure that your system continues to functions as intended, you must test your system weekly. Please
refer to “Testing Your System” on page 12 of this manual. If your system does not function properly, call
your installing company for service.
Monitoring
This system is capable of transmitting alarms, troubles and emergency information over telephone lines
to a monitoring station.
NOTE: The monitoring function must be enabled by the installer before it becomes functional.
General System Operation
Your security system is made up of a DSC control panel, one or more keypads and various sensors and
detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The metal
cabinet contains the system electronics, fuses and stand-by battery. There is no reason for anyone but
the installer or service professional to have access to the control panel.
All the keypads have an audible indicator and command entry keys. The LED keypads have a group of
zone and system status lights. The LCD keypad has an alphanumeric liquid crystal display (LCD).
The keypad is used to send commands to the system and to display the current system status. The
keypad(s) will be mounted in a convenient location inside the protected premises close to the entry/exit
door(s).
The security system has several zones of area protection and each of these zones will be connected to
one or more sensors (motion detectors, glassbreak detectors, door contacts, etc.). A sensor in alarm will
be indicated by the corresponding zone lights flashing on a LED keypad or by written messages on the
LCD keypad.
IMPORTANT NOTICE
A security system cannot prevent emergencies. It is only intended to alert you and – if included –
your monitoring station of an emergency situation. Security systems are generally very reliable
but they may not work under all conditions and they are not a substitute for prudent security
practices or life and property insurance. Your security system should be installed and serviced by
qualified security professionals who should instruct you on the level of protection that has been
provided and on system operations.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
System Information
Fill out the following information for future reference and store this manual in a safe place.
Access Codes
Your Master Code is:__________________________________________
Additional Access Codes:
01 __________________ 09 ____________________ 17 ____________________ 25 ________________
02 __________________ 10 ____________________ 18 ____________________ 26 ________________
03 __________________ 11 ____________________ 19 ____________________ 27 ________________
04 __________________ 12 ____________________ 20 ____________________ 28 ________________
05 __________________ 13 ____________________ 21 ____________________ 29 ________________
06 __________________ 14 ____________________ 22 ____________________ 30 ________________
07 __________________ 15 ____________________ 23 ____________________ 31 ________________
08 __________________ 16 ____________________ 24 ____________________ 32 ________________
Zone Information
There are ________ active zones on the system.
Zone
Protected Area
Zone Type
1
2
3
4
5
6
7
8
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
[F] FIRE __________________________________________
[A] AUXILIARY ____________________________________
[P] PANIC ________________________________________
The Exit Delay Time is________ seconds.
The Entry Delay Time is _______ seconds.
For Service
Central Station Information:
Account #: ___________________________________
Telephone #:_________________________________
Telephone #:_________________________________
Installer Information:
Company: ___________________________________
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Access Codes
Access codes are used to arm and disarm the system. There are 37 access codes available: 1 master
code, 32 regular access codes, 2 duress codes and 2 supervision codes. Ask your installer for more
information on using the duress and supervision codes.
Only the Master Code can be used to program additional security codes and to change other system
features as well as to arm and disarm the security system. The Master Code will be supplied to you by your
installer. All keypad entries are made by pressing one key at a time.
All access codes can be programmed by following the procedure outlined in “Programming Security
Codes” on page 6.
NOTE: An access code can be a four or six digit number depending on how your installer has
programmed your system. Ask your installer for more information regarding access codes.
Arming the System
Arming Procedure:
In an attempt to reduce false alarms, your system is designed to notify you of an improper exit when
arming the system. With the Push to Set or the Final Door Set, if you enter your code to arm the system
your panel will start an infinite exit delay. The keypad will sound a beep once ever second. If you violate a
zone while exiting the premise the keypad will sound 6 quick beeps when you walk past a motion
detector or open a window or door with a magnetic contact on it. When you have opened and closed the
Final Exit door or after closing the final exit door have pressed the Push to Set button, the keypad will
continue to beep once every second for 5 seconds. The panel uses these 5 seconds to allow time for the
detectors on the system to settle back to their normal states. At the end of this settling time the system
checks for detectors/windows/doors that may be open. If any of these are open the panel will sound a
tone and arming will be canceled. If this occurs, you must re-enter the premises, check the system,
close any open zones, and the follow the arming procedure again.
Arming from an LED Keypad:
If the Ready light is ON, the system is ready for arming. If the Ready light is OFF, check to see that all doors and
windows are closed and that motion is stopped in areas covered by motion detectors. The system cannot be
armed unless the Ready light is ON indicating that all zones are closed and the system is in the Ready state.
Enter your access code. As each digit is entered, the keypad sounder will beep. If the access code was entered
incorrectly, the keypad buzzer will sound steadily for one second. If this occurs, press the [#] key and re-enter
your access code. If the correct access code is entered, the keypad sounder will beep quickly and the Armed
light will come ON. Exit the premises through the door indicated by your installer as the Exit/Entry door.
The panel will provide an exit delay period, indicated by keypad beeps, for you to exit the premises without
causing an alarm. At the end of the exit delay period, all keypad lights, except the Armed light, will turn OFF and
the system will be armed. You can restart the exit delay once by pressing the Away button before the exit delay
expires. The exit delay time can be changed by your installer.
Arming from an LCD Keypad:
If the Ready light is ON, the system is ready for arming. If the Ready light is OFF, this
Secure System
message will appear on the LCD display. Ensure all doors and windows are closed
Before Arming<>
and motion is stopped in areas covered by motion detectors. The system cannot be
armed unless the Ready light is ON indicating that all zones are closed and the system
is in the Ready state.
When this message appears, use the arrow (< >) keys to verify that the system is clear
Enter Code to
Arm System
of troubles and that no zones are bypassed unintentionally (see “Viewing Trouble
<>
Conditions” on page 11, and “Zone Bypassing” on page 10).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
If this display is showing, the system is in the Ready state and may be fully armed. To
arm the system, enter your access code.
Enter Code to
Arm System
Once the correct access code has been entered, the display will be as shown. The
panel will provide an exit delay period, also indicated by keypad beeps, for you to exit
the premises without causing an alarm. You can restart the exit delay once by pressing
the Away button before the exit delay expires. Exit through the door indicated by your
installer as the Exit/Entry door.
Exit Delay in
Progress
This message will be displayed once the exit delay expires and the system is fully
armed.
Enter Code to
Disarm System
If this message appears, be aware of which zones are bypassed and why (see “Zone
Bypassing” on page 10). NOTE: If you arm the system with a zone bypassed or
with a trouble present, your security protection is reduced.
* WARNING *
Bypass Active
Alternate Arming Methods
Away Arming
Arming the system in the Away mode will have all interior zones and perimeter zones active. If motion is
detected in the interior zones, or if one of the perimeter zones is violated, the alarm sequence will begin.
To arm in the Away mode, enter your access code and exit the premises through a designated Exit/Entry
door. The system will recognise that occupants have left the premises. Once the exit delay expires, the
system will be fully armed.
You can restart the exit delay once by pressing the Away button before the exit delay expires.
Stay Arming
This feature, will allow you to arm the perimeter zones while leaving the interior zones inactive so that you
can remain on the premises while the system is armed. When you press the Stay Key and then enter your
security code to arm the system, it will arm in the Stay mode, automatically bypassing the interior zones.
The interior zones can be reactivated at any time by entering [✱][1] at any keypad. If you reactivate the
interior zones, be sure to only inhabit areas not covered by motion detectors. To access areas protected
by motion sensors, you must enter your security code and disarm the system.
Quick Exit
When the Quick Exit feature is enabled, pressing [✱][0] while the system is armed will provide a two
minute window for you to exit the premises. During this time, you may only open and close the
designated Entry/Exit door once. Once the door is closed, the panel will end the two minute quick exit
delay. If the door is opened again, or if the door is not closed after two minutes, or if another zone is
opened, the panel will begin the entry delay. Your installer will inform you if the Quick Exit feature has
been enabled on your system.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Disarming the System
Disarming from an LED Keypad:
Enter the premises through a designated Exit/Entry door; entering by any other door will sound an
immediate alarm. As soon as the Exit/Entry door is opened, the keypad will beep to indicate that the
system should be disarmed. Go to the keypad and enter your access code. If an error is made entering
the code, enter your code again. As soon as the correct code is entered, the Armed light will go out and
the keypad will stop beeping.
The correct access code must be entered before the entry delay period expires. If a valid access code is
not entered during this time, the system will go into alarm. The entry time delay may be changed by your
installer.
If an alarm occurred while the system was armed, the Memory light and the zone light corresponding to
the zone which caused the alarm will flash for 30 seconds. After the 30 second period, the Memory light
and zone light will stop flashing and the panel will return to the Ready state. Pressing the [#] key during
the 30 second period will cancel the alarm memory display. To view other alarms, press [✱][3].
If a trouble was detected when the panel is disarmed, the Trouble light will turn ON (See “Viewing Trouble
Conditions” on page 11 to determine the source of the trouble.) Please note that troubles will not display
while the system is in the Alarm Memory Display mode.
Disarming Procedure:
Upon entering through a designated Exit/Entry door, the keypad will beep and the entry delay will
commence, reminding you to disarm the system. The keypad will display the following message...
Enter your access code. If an error is made in entering the code, press [#] to
Entry Active
cancel and then re-enter the code again. When a valid access code is entered, the
Enter Your Code
keypad will stop beeping. If no alarms occurred while the panel was armed, and
there are no troubles, the display will read...
System Disarmed
No Alarm Memory
After about five seconds, the system will return to the Ready state and the display
will read...
Enter Code to
Arm System
If an alarm occurred while the system was armed, this message will be displayed. Use
the arrow (< >) keys to view which zones caused the alarm. If a zone is still in alarm,
the display will show the following message to indicate that a zone is open...
View Memory <>
“Zone of Alarm”
Secure System
Before Arming<>
Upon disarming and if a trouble is present, this message will be displayed. Use the
Enter Code to
Arm System
arrow (< >) keys to view which troubles are affecting the system (see “Viewing Trouble
<>
Conditions” on page 11).
NOTE: If you return and find that an alarm has occurred while you were away, it is possible that an
intruder may still be on the premises. Take appropriate action.
The alarm memory is cleared each time the panel is armed so that any alarms showing are alarms
that occurred only during the last armed period.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
If An Alarm Sounds
Fire Alarm
If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow your
emergency evacuation plan immediately (see “Fire Escape Planning” on page 15).
Intrusion Alarm
If an intrusion alarm sounds, indicated by a continuous Bell or Siren, the alarm may be silenced by entering
your access code, if the alarm was unintentional.
You can determine the source of the alarm by following the instructions in the “Disarming” section (see
page 5). Once the source of the alarm has been corrected, the system will require a reset.
NOTE: A fire alarm has priority over a burglary type alarm (all monitored systems).
Resetting the system
Your installer will let you know if your system is set up so that if there is an alarm, you will need to reset
your system. This is done to ensure that after an alarm your system is working properly. There are two
ways your system can be reset.
Engineer’s Reset
If an alarm has occurred on your system, the system will not allow you to rearm (Read light is OFF). You
will need to contact you installer. They will check and reset the system for you. After the reset is
preformed your system will function properly again.
Remote Reset
After you have silenced an alarm on your system, the keypad will display a message “Remote Reset Rqd”
along with a 4-digit Lock Code. The display will pause for 3 seconds, and then repeat the lock code. If
your system needs resetting you will not be able to perform any system function, except for viewing the
alarm memory ([*][3]) or activating command outputs such as sensor reset ([*][7]). The rest of the system
will function as normal (i.e. alarms and troubles will still be monitored).
You will only be able to reset the system by entering a Reset Code. To get the reset code you will have to
contact your installer or central station. Provide them with the 4-digit Lock Code number that is displayed
on your keypad. Your installer or central station will in turn provide you with a new 4-digit Reset Code.
Enter the Reset Code into the keypad. The keypad will reset and function system will return to normal.
Function Keys
The PC5508Z and LCD5500Z keypads have five function keys – marked Stay, Away, Chime, Reset and
Exit – which allow easy single-button activation of the most commonly used features. If these keys have
been enabled by your installer, you can execute the programmed function by pressing and holding the
corresponding key for two seconds.
For more information regarding the operation of the function keys, talk to your alarm system installer.
Programming Security Codes
Programming codes from an LED Keypad:
The Master Code
To program the Master Code, enter [✱][5][current Master Code][40][new Master Code]. The Master Code
must be four digits unless otherwise indicated by your installer. Enter digits 0 through 9 only. Press [#] to
return to the Ready state.
Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We
recommend that the factory default or obvious codes such as [1111] or [1234] not be used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Codes
Up to 32 additional access codes (01 through 32) may be programmed.
To program a new code:
Enter [✱][5][Master Code][code number 01 to 32][new access code]. The code number is a double digit
from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer. Enter digits
0 through 9 only. Press [#] to return to the Ready state.
If an access code already exists for the code number you have selected, it will be replaced by the new
code. Be sure to record your new code(s) on the “System Information” page in this book.
To erase a code:
Enter [✱][5][Master Code][code number 01 to 32][✱]. Press [#] to return to the Ready state. The Master
code cannot be erased.
Programming codes from an LCD Keypad:
Master Code
Press the [✱] key to enter the function list. Scroll (< >) to...
Press [5] or [✱]. The display will read...
Press (*) for<>
Access Codes
Enter your current Master Code. The display will read...
Enter Master
Access Code
“40P” represents the Master Code. Press the [✱] key to indicate that you wish to
program the Master Code. The display will read...
(*) to Edit <>
User Code
40P
Enter the new Master Code. The Master Code must be four digits unless otherwise
indicated by your installer. Enter digits 0 through 9 only. Once the new code is
entered, the keypad will beep 3 times and the display will read...
Enter New Code
1234
<>
Press [#] to exit the code programming function.
(*) to Edit <>
User Code
40P
Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We
recommend that the factory default Master Code [1234] not be used.
Additional Access Codes
To erase, add or change a user code, press [✱] to enter the functions list. Use the arrow (< >) keys to
scroll to the following message...
Press [✱]. Display will read...
Press (*) for<>
Access Codes
Enter the Master Code. Display will read...
Enter Master
Access Code
Use the scroll keys (< >) to find the access code – indicated by “01P” to “32P” – you
[*] to Edit <>
wish to add, change or delete. Press the [✱] key to select the code you wish to alter.
User Code
01P
The display will read...
To add or change a code, enter the new code. Access codes must be four digits
unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete an
access code, enter [✱]. Once the 4 digit code or [✱] has been entered, the keypad
sounder will beep 3 times and the display will read...
Enter New Code
1234
<>
The “P” means the code has been programmed. If there is no “P” then that code is deleted.
[*] to Edit <>
Press [#] to exit the code programming function. The Master code cannot be erased.
01P
User Code
Remember to record your new code(s) on the “System Information” page in this booklet.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PC5508Z LED Keypad
Emergency Keys (All Keypads)
PC5508Z, LCD5500Z:
Press both * Keys for two seconds to send a
FIRE transmission.
Press both * Keys for two seconds to send an
AUXILIARY transmission.
Press both * Keys for two seconds to send a
PANIC transmission.
* IMPORTANT NOTE (All Keypads): The Fire,
Auxiliary and Panic keys will NOT function
unless programmed by the installer. If these
keys are in service and the installer has enabled
audible feedback, holding down the key for two
seconds will cause the keypad sounder to beep
indicating that the input has been accepted and
transmission is underway.
NOTE: In the U.S.A. the [A] and
keys are
programmed to be used for non-medical
emergencies only, as per UL requirements.
Display Lights (PC5508Z Keypad)
Memory Light
Upon disarming, if an alarm has occurred while the
system was armed, the Memory light will turn ON
(See “Disarming the System” on page 6).
Bypass Light
If the Bypass light is ON, one or more zones are
bypassed (See “Zone Bypassing” on page 10).
Fire Light
If the Fire light is ON, a fire alarm has occurred
(See “Fire Alarm Operation” on page 14).
Program Light
The Program light will flash when you are
programming access codes, or performing other
programming functions. If someone is
programming at another keypad, the Program light
will turn ON to indicate that the system is busy.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD5500Z Keypad
The Liquid Crystal Display (LCD) displays
prompts and system information on two 16
character lines.
If “< >” appears, more information can be
accessed by using the arrow (< >) keys. Press [<]
to see the previous function or item of information.
Press [>] to advance the display to next function or
item of information.
Press the keys on the number pad as prompted by
the LCD display to view alarms or troubles, to arm
and disarm the system and to bypass zones.
To exit a function and return to the Ready state,
press [#].
To select a function press [✱].
Display Lights (All Keypads)
Ready Light
If the Ready light is ON, the system is ready for arming.
The system cannot be armed unless the Ready light is
ON (see “Arming the System” on page 4).
Armed Light
If the Armed light is ON, the system has been armed
successfully.
Trouble or System Light
If the Trouble light is ON, see “Viewing Trouble
Conditions” on page 11.
• Important Note •
Test system weekly and have any system trouble
conditions corrected by your alarm installer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Zone Bypassing
The zone bypassing function is used when access is needed to part of the protected area while the
system is armed. Zones which are temporarily out of service due to damaged wiring or contacts may be
bypassed to allow system arming until repairs can be made.
Bypassed zones will not cause an alarm. Zones cannot be bypassed once the system is armed.
Bypassed zones are automatically cancelled each time the system is disarmed and must be reapplied
before the next arming.
NOTE: For security reasons, your installer may program the system to prevent you from bypassing
certain zones. Bypassing zones reduces your security protection. If you are bypassing a zone due
to damaged wiring or contacts, please call a service technician immediately so that the problem
can be resolved and your system returned to proper working order. Do not unintentionally bypass
zones when you arm your system.
To bypass zones from an LED keypad:
Start with the system in the Ready state. Enter [✱][1][Zone number(s) to be bypassed].
Enter the zone number(s) as a double digit from 01 to 08. As each zone is bypassed, the corresponding
zone light will turn ON. If a zone is bypassed by mistake, press that zone number again and the zone light
will turn OFF, indicating that the zone is not bypassed. Press [#] to return to the Ready state.
When the system is armed, the Bypass light will be ON if one or more zones are bypassed.
To bypass zones from an LCD keypad:
To bypass a zone, the system must be in the Ready state. The display will read...
Press the [✱] key to enter the functions menu. The display will read...
Enter Code to
Arm System
Press the [✱] key to enter the zone bypassing mode. The display will read...
Press (*) for<>
Zone Bypass
Use the arrow (< >) keys to find the zone to be bypassed and press the [✱] key to select
it. The display will read...
Zone Search <>
“Zone Name”
“B” will appear on the display to show that the zone is bypassed. To unbypass a zone,
enter the zone number; the “B” will disappear from the display to show that the zone is
no longer bypassed.
Zone Search <>
“Zone Name”
B
This display will be shown if a zone was open when you entered the bypassing
command. The open zone will be represented by “O”. If you bypass the open zone, the
“O” will be replaced by a “B”.
Zone Search <>
“Zone Name”
O
To exit the bypassing mode and return to the Ready state, press the [#] key.
Bypass Groups
A Bypass Group is a selection of zones programmed into the system’s memory. The Bypass Group can
be recalled upon arming to allow quick bypassing of a selection of zones on a regular basis.
To program the Bypass Group, perform the following:
1. Press [✱][1], followed by your access code, if necessary.
2. Enter the zone numbers of the zones to be included in the Bypass Group. Each zone number is two digits.
3. Once all zones to be included have been selected, press [9][5].
To select the Bypass Group when arming the system, perform the following:
1. Press [✱][1], followed by your access code, if necessary.
2. Press [9][1].
3. Press [#] to return to the Ready state. Arm the system.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Zone Bypassing Features
To recall the last set of bypassed zones, press [✱][1][9][9]. Arm the system. The Bypass light will turn on
to indicate that zones are bypassed.
To clear all bypassed zones, press [✱][1][0][0].
Viewing Trouble Conditions
The control panel continuously monitors a number of possible trouble conditions. If one of these trouble
conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.
NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your
installing company for service.
To view troubles from an LED Keypad:
A trouble will be indicated by the Trouble light (or System light on a PC1555RKZ keypad) which will
remain ON until the trouble condition is cleared. If you cannot determine the cause of the trouble
condition, contact your installer for assistance.
To view the type of trouble condition, press [✱][2]. One or more zone lights will turn ON, indicating the
various trouble conditions:
ZONE LIGHT
TYPE OF TROUBLE
1 ................. Service required. Call your installation company for service.
2 ................. Indicates the loss of AC power. When this trouble occurs, the Trouble (or System) light
will turn ON but keypad buzzer will not sound.
3 ................. Telephone line trouble.
4 ................. The panel has failed to communicate with the central station.
5 ................. Zone fault. Press [5] and the zone light(s) corresponding to the faulted zones will turn ON.
6 ................. Zone tamper. Press [6] and the zone light(s) corresponding to the tampered zones will
turn ON.
7 ................. Low zone battery. This trouble is generated when a wireless device exhibits a low
battery condition.
Press [7] one, two, or three times to view which devices are experiencing battery
failure. The following will occur:
Keypad beeps: Keypad displays:
Press [7]
Press [7] again
1
2
Zones with low batteries (LED keypad - zone lights 1 to 8)
Handheld keypads with low batteries (LED keypad - zone lights
1 to 4)
Press [7] again
3
Wireless keys with low batteries (LED keypad - zone lights 1 to
8). To view the battery conditions of wireless keys 9 through 16,
you must be at an LCD keypad.
8 ................. Loss of time on system clock. To set the system time, following the instructions in
“Setting System Date and Time”.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To view troubles from an LCD Keypad:
From the Ready state, use the arrow (< >) keys to scroll to the following message.
Press [✱] [2] key to view the trouble. The message will read...
System Trouble
(*2) to View <>
Use the arrow (< >) keys to view which troubles are present on the system. Once you
View Trouble <>
have scrolled through the list of troubles, press the [#] key to exit the Trouble Viewing
“Trouble Message”
mode and return to the Ready state.
Setting the System Date and Time
To set the system time, enter [✱] [6] followed by the Master Code. Press [1]. The keypad will now accept
10 consecutive digits:
• Enter the Time in Hours and Minutes using the 24 Hour format (00:00 to 23:59).
• Enter the Date in Months, Days and Years (MM DD YY).
NOTE: If you have an LCD keypad, your installer may have programmed your system to display the
time and date while the keypad is idle. If this is the case, you may have to press the [#] key to clear
the date and time before entering an access code to arm the system, or before performing any
other keypad function.
Testing Your System
Alarm Test
The Alarm Test provides two second test of the keypad sounder and bell or siren. Begin with the panel in
the Ready state.
From an LED keypad, Enter [✱][6][Master Code][4] then press [#] to return to the Ready state.
From an LCD keypad, press [✱] to enter the functions list. Use the arrow (< >) keys to scroll to find “User
Functions” and press [✱] to select. Enter your Master Code and scroll to find the following message...
Press [✱] to perform an Alarm Test. The keypad will display the following message...
Select Option<>
System Test
Press [#] to return to the Ready state.
System Test
In Progress
Full System Test
We recommend that you test your system weekly. Should the system fail to function properly, call your
installation company immediately for service.
NOTE: Perform system tests during off-peak hours, such as early morning or late evening.
1. Inform the monitoring station that you are testing your system.
2. Begin with the system in the Ready state.
3. Perform a Bell/Battery test by pressing [✱][6][Master Code][4]. The bell and keypad buzzer will sound
for two seconds and all keypad lights will turn ON. Press [#] to exit.
4. Activate each sensor in turn (e.g. open a door/window or walk in motion detector areas).
From an LED keypad, observe the zone light turn ON when the zone is activated. The zone light will
turn OFF when the system restores to normal (i.e. door or window closed).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
From an LCD keypad, the following message will be displayed when each zone is activated...
Secure System
Before Arming <>
Use the arrow (< >) keys to view which zone is open. This message will disappear
when the zone is restored.
5. If the panel has any fire zones, activation will cause the alarm signal to sound in a pulsed mode.
CAUTION: Do not use an open flame or burning materials to test a smoke or heat detector. Contact
your installer for information on safe methods of testing detectors.
6. When testing is complete, call and advise the monitoring station. Should the system fail to function
properly, contact your installer.
NOTE: Some features described above will not be functional unless enabled by your installer.
Please ensure that your installer has advised you which features are functional on your system.
Door Chime Feature
The door chime feature is used to provide a tone from the keypad each time a door or window is opened
or closed. The doors and windows which will provide this indication are programmed by your installer.
To activate the door chime from an LED Keypad:
Enter [✱][4] to turn the door chime feature ON and OFF. When the command is entered, the keypad
buzzer will beep 3 times if the door chime feature is enabled and will sound one long beep if it is
disabled.
To activate the door chime from an LCD Keypad:
Press [✱] to enter the function list, then scroll to find...
Press [✱] or [4] to enable or disable the Door Chime feature. Press [#] to return to the
Ready state.
Press (*) For<>
Door Chime
Keypad Options
All Keypads
Keypad Sounder Control
The LCD keypad will allow you to select from 21 different keypad tones. From an LCD keypad, enter
[✱][6][Master Code], then use the arrow keys (< >) to scroll to the message "Keypad Buzzer Control".
Press [✱] to select. Use the arrow keys (< >) to scroll to the desired keypad sound level and press the [#]
key to exit. This feature can be accessed on LED keypads by holding the [✱] key.
LCD Keypads Only
The following three options are accessed by entering [✱] [6] [Master code]. Use the arrow (< >) keys
to scroll to the appropriate message and press [✱] to select.
Brightness Control
The LCD keypad will allow you to select from 10 different backlighting levels. Use the arrow keys (< >) to
scroll to the desired backlighting level and press the [#] key to exit.
Contrast Control
The LCD keypad will allow you to select from 10 different display contrast levels. Use the arrow keys (<
>) to scroll to the desired contrast level and press the [#] key to exit.
Viewing the Event Buffer from an LCD Keypad
Select “View Event Buffer” from the [✱][6] menu. The keypad will display the event, event number, time
and date along with the zone number and user code, if applicable. Press [✱] to toggle between this
information and the event itself. Use the arrow keys (<>) to scroll through the events in the buffer. When
you have finished viewing the Event Buffer, press the [#] key to exit.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading Enable
To enable a six-hour downloading window from any system keypad, enter [✱] [6] [Master code] [5].
During this time, the panel will answer incoming downloading calls. For more information, please ask your
installer.
Fire Alarm Operation
Alarm
On a fire alarm, the bell or siren will pulse ON and OFF. The transmission of the alarm to the monitoring
station is delayed for 30 seconds. If the alarm is not cleared within the 30 second delay, then it will be
transmitted to the monitoring station.
Silence
To silence the bell or siren, press the [#] key. If the alarm is silenced and the smoke detector is not reset,
the alarm will resound after 90 seconds.
Resetting Smoke Detectors
Once the smoke detector is reset, if it still detects smoke, the alarm sequence will resound as described
above. If there is no smoke, the system will return to normal.
To reset smoke detectors from an LED Keypad:
Press [✱][7][2].
To reset smoke detectors from an LCD Keypad:
Press [✱] to enter the function list. Scroll to find:
Press (*) For <>
Output Control
Press [✱] to select the output control. The display will read...
Select Output <>
Command Output #1
Use the arrow (< >) keys to find the following message and press the [✱] key to
select...
Select Output <>
Command Output #2
NOTE: If you suspect that a fire alarm has transmitted and that there is no fire condition, call the
monitoring station to avoid an unnecessary response. If a fire condition is apparent, follow your
evacuation plan immediately. If the alarm sounds at night, evacuate immediately.
NOTE: The description above may not be applicable depending on how your installer has
programmed the fire alarm operations on your system. Ask your installer for more information
regarding your system's operation.
Household Fire Safety Audit
Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit
be conducted and a fire escape plan be developed.
1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded
lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or household
service, have a professional evaluate these units.
2. Are all flammable liquids stored safely in closed containers in a well ventilated cool area? Cleaning
with flammable liquids should be avoided.
3. Are fire hazardous materials (matches) well out of reach of children?
4. Are furnaces and wood burning appliances properly installed, clean and in good working order? Have
a professional evaluate these appliances.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Escape Planning
There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very
important that a family escape plan be developed and rehearsed.
1. Every family member should participate in developing the escape plan.
2. Study the possible escape routes from each location within the house. Since many fires occur at night,
special attention should be given to the escape routes from sleeping quarters.
3. Escape from a bedroom must be possible without opening the interior door.
Consider the following when making your escape plans:
• Make sure that all perimeter doors and windows are easily opened. Ensure that they are not painted
shut, and that their locking mechanisms operate smoothly.
• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue
should be developed. This includes making sure that those who are to perform the rescue can
promptly hear the fire warning signal.
• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as
training in its use.
• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in
winter; outdoor furniture or equipment should not block exits.
• Each person should know of a predetermined assembly point where everyone can be accounted for
i.e.: across the street or at a neighbour's house. Once everyone is out of the building, call the Fire
Department.
• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not
gather belongings or pets as this wastes valuable time. Once outside, do not re-enter the house.
Wait for the fire department.
• Write the fire escape plan down and rehearse it frequently so that should an emergency arise,
everyone will know what to do. Revise the plan as conditions change, such as the number of people
in the home, or if there are changes to the building's construction.
• Make sure your fire warning system is operational by conducting weekly tests (see “Testing Your
System” on page 12). If you are unsure about system operation, contact your installing dealer.
• We recommend that you contact your local fire department and request further information on fire
safety and escape planning. If available, have your local fire prevention officer conduct an in-house
fire safety inspection.
Maintenance
With normal use, the system requires minimum maintenance. The following points should be observed.
1.Do not wash the security station with a wet cloth. Light dusting with a slightly moistened cloth should
remove normal accumulations of dust.
2.The battery/bell test is designed to determine battery condition. We recommended, however, that the
stand-by batteries be replaced every three years.
3.For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion
detectors or glassbreak detectors, consult the respective manufacturer’s literature for testing and
maintenance.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoiding False Alarms
10 Points to Remember
1. Make sure that the alarm system is operated only by persons who have been properly instructed.
2. Carefully close and secure all doors and windows before setting the alarm.
3. Check that movement detectors are not obstructed.
4. Do not allow sources of heat or sound, or permit moving objects in range of your movement detectors.
Check that there is no unstable stock, and ensure that no birds or stray animals are present.
5. Know the specified entry/exit route and keep to it when the system is unset and set. Do not enter other
protected areas until the system is unset.
6. Treat your alarm system with care and report all accidental damage to your alarm company.
7. Inform your alarm company of any changes in the building and storage of contents which may affect the
alarm system.
8. Remember your code word (if applicable). In the event of a false alarm from a monitored private
residential property wait by your telephone for a verification call from the monitoring centre. For non-
domestic installations (e.g. commercial or retail) call the monitoring centre immediately to abort the false
alarm. Do not set the alarm system on again after a false call until the fault has been determined.
9. Make sure your regular maintenance checks are carried out by your alarm company. Remember that
repetitive false alarms may give rise to withdrawal of police response. Record all incidents/visits in this
record book.
10. Check that all keys are readily available and that code numbers (if applicable) are known before entry.
Notify the central monitoring station of any changes in the set and unset times, if these are monitored.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Digital Security Controls Ltd. warrants the original purchaser that
for a period of twelve months from the date of purchase, the prod-
uct shall be free of defects in materials and workmanship under
normal use. During the warranty period, Digital Security Controls
Ltd. shall, at its option, repair or replace any defective product
upon return of the product to its factory, at no charge for labour
and materials. Any replacement and/or repaired parts are warranted
for the remainder of the original warranty or ninety (90) days,
whichever is longer. The original owner must promptly notify Digi-
tal Security Controls Ltd. in writing that there is defect in material
or workmanship, such written notice to be received in all events
prior to expiration of the warranty period.
Digital Security Controls Ltd.’s liability for failure to repair the
product under this warranty after a reasonable number of attempts
will be limited to a replacement of the product, as the exclusive
remedy for breach of warranty. Under no circumstances shall Digi-
tal Security Controls Ltd. be liable for any special, incidental, or
consequential damages based upon breach of warranty, breach of
contract, negligence, strict liability, or any other legal theory. Such
damages include, but are not limited to, loss of profits, loss of the
product or any associated equipment, cost of capital, cost of substi-
tute or replacement equipment, facilities or services, down time,
purchaser’s time, the claims of third parties, including customers,
and injury to property.
International Warranty
Disclaimer of Warranties
The warranty for international customers is the same as for any
customer within Canada and the United States, with the excep-
tion that Digital Security Controls Ltd. shall not be responsible for
any customs fees, taxes, or VAT that may be due.
This warranty contains the entire warranty and shall be in lieu
of any and all other warranties, whether expressed or implied
(including all implied warranties of merchantability or fitness
for a particular purpose) And of all other obligations or liabili-
ties on the part of Digital Security Controls Ltd. Digital Secu-
rity Controls Ltd. neither assumes nor authorizes any other per-
son purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability
concerning this product.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in
question to the point of purchase. All authorized distributors and
dealers have a warranty program. Anyone returning goods to Digi-
tal Security Controls Ltd. must first obtain an authorization num-
ber. Digital Security Controls Ltd. will not accept any shipment
whatsoever for which prior authorization has not been obtained.
This disclaimer of warranties and limited warranty are governed
by the laws of the province of Ontario, Canada.
WARNING: Digital Security Controls Ltd. recommends that the
entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product to
fail to perform as expected.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship re-
lating to normal use. It does not cover:
• damage incurred in shipping or handling;
• damage caused by disaster such as fire, flood, wind, earthquake
or lightning;
• damage due to causes beyond the control of Digital Security
Controls Ltd. such as excessive voltage, mechanical shock or
water damage;
Out of Warranty Repairs
Digital Security Controls Ltd. will at its option repair or replace out-
of-warranty products which are returned to its factory according to
the following conditions. Anyone returning goods to Digital Secu-
rity Controls Ltd. must first obtain an authorization number. Digital
Security Controls Ltd. will not accept any shipment whatsoever for
which prior authorization has not been obtained.
• damage caused by unauthorized attachment, alterations, modi-
fications or foreign objects;
• damage caused by peripherals (unless such peripherals were
supplied by Digital Security Controls Ltd.);
• defects caused by failure to provide a suitable installation en-
vironment for the products;
Products which Digital Security Controls Ltd. determines to be re-
pairable will be repaired and returned. A set fee which Digital Secu-
rity Controls Ltd. has predetermined and which may be revised from
time to time, will be charged for each unit repaired.
• damage caused by use of the products for purposes other than
those for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper
application of the products.
Products which Digital Security Controls Ltd. determines not to be
repairable will be replaced by the nearest equivalent product avail-
able at that time. The current market price of the replacement prod-
uct will be charged for each replacement unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2000 Digital Security Controls Ltd.
Toronto, Ontario
Printed in Canada 29005122 R001
Download from Www.Somanuals.com. All Manuals Search And Download.
|