USER GUIDE
Turbosound Ltd
Star Road, Partridge Green
West Sussex RH13 8RY United Kingdom
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155
Issue 1.0 © Turbosound Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Warranty ....................................................................................................................................................25
Contact Information..................................................................................................................................26
Customer Service................................................................................................................................................... 26
Product Information............................................................................................................................................... 26
Notes...............................................................................................................Error! Bookmark not defined.
MILAN Mi0 user manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
EC Declaration of Conformity
Manufacturer
Turbosound Ltd, Star Road, Partridge Green, West Sussex, RH13 8RY, UK
Standards
This product complies with directive 89/336/EEC (EMC) and following modifications 92/31/EEC and
93/68/EEC, as stated in EN 55103-1 and EN 55103-2 and with directive 73/23/EEC (LVD) and
following modifications 93/68/EEC as stated in EN 60065 standard. Under the EM disturbance, the
ratio of signal-noise will be changed above 10dB.
FCC Compliance
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) the device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Category
Professional apparatus for use in Commercial Light Industrial and controlled EMC environments.
CE Marking
All products are marked in accordance with the relevant statutory requirements.
Simon Blackwood (Managing Director)
Dominic Harter (Sales Director)
July 2011
MILAN Mi0 user manual
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Safety considerations
Before using your Milan loudspeaker please read the following information as it pertains to your
safety and the reliability of your product.
Read and retain these instructions.
Heed all warnings.
Follow all instructions.
Do not use this product near water.
Do not install near any heat sources such as radiators, stoves, boilers, or other apparatus
that produces heat.
Do not allow the mains cable to become damaged, twisted, cut or caught under other
equipment.
Do not use the loudspeaker with AC mains supplies lower than 100v or higher than 240v,
as damage may result.
Use only accessories and attachments approved by the manufacturer. If the product is to
be permanently installed use only rigging hardware approved by Turbosound.
Unplug the loudspeaker during lightning storms or when it is not to be used for long
periods of time.
This equipment must be grounded (earthed).
Be careful when lifting the loudspeaker, for instance when placing onto speaker stands or
poles. Make sure that you are lifting within your personal capability.
Keep the exterior of the loudspeaker enclosure clean, and clean only with a dry cloth.
Do not install the loudspeaker in outdoor environments where the product could be
subjected to moisture, excessive temperatures or prolonged UV light exposure.
Electrically powered devices such as this product can present dangerous shock hazards
when wet or exposed to moisture.
This product is not suitable for fixed installation in outdoor environments.
MILAN Mi0 user manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Introduction
Congratulations, you have purchased a professional loudspeaker product from the Milan series of
loudspeakers, designed to give you the best in audio quality and many years of reliable, trouble-
free operation. It offers excellent pattern control, safe and practical rigging hardware, superior
audio quality, proven reliability, ease of setup, consistent performance, and the backing of a world
leader in acoustics technology including a comprehensive warranty against manufacturing
defects. Please read through this manual carefully before you attempt to operate the loudspeaker
system. It contains valuable information which will enable you to quickly and easily connect the
loudspeakers to your outboard equipment; and important system and set-up checks.
Thanks
Thank you for choosing a TURBOSOUND loudspeaker product for your application.
By engaging in an on-going rigorous program of research and development all TURBOSOUND
products are carefully engineered for world class performance and reliability.
If you would like further information about this or any other TURBOSOUND product, please
We look forward to helping you in the near future.
Unpacking
After unpacking the unit please check carefully for damage. If damage is found, please notify the
carrier concerned at once. You, the consignee, must instigate any claim. Please retain all
packaging in case of future re-shipment.
Contents
Milan Mi0 loudspeaker
IEC mains cable
User Guide
Turbosound logo sticker
MILAN Mi0 user manual
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Getting Started
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE
LINE LEVEL
GROUND LIFT
POWER
MIC IN
MIX OUT
LINE IN
ON
1. Turn the Mic Gain and Line Level controls fully anticlockwise (MIN).
2. Set the Bass and Treble tone controls to their centre position (no boost or cut).
3. Connect your signal sources (mixing console, keyboard, microphone, acoustic guitar) to
the appropriate input connector.
4. Switch on the mixer or other source and make sure the output faders or master output
level controls are turned fully down.
5. Ensure that the mains voltage requirement of you model as indicated by the voltage label
(230v or 120v) matches your local AC mains supply. Connect the AC mains cable to the
Milan loudspeaker and turn on the mains switch. The green POWER LED will illuminate
to indicate that mains power is connected.
6. Increase the output level of the signal source to a normal operating level.
7. Slowly turn up the Milan loudspeaker’s level control(s) until a suitable volume level is
reached. The SIG/LIMIT LED illuminates green to indicate signal present and flashes red
when limiting. It is normal for the SIG/LIMIT LED to flash occasionally, but excessive or
prolonged illumination indicates that the input signal is too high or additional speakers
are required.
MILAN Mi0 user manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
8. When shutting down the Milan system, first turn down the input level controls, then
switch off the mains power before turning off the mixer or signal source.
MILAN Mi0 user manual
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Self-Powered Loudspeakers
The Milan Mi0 self-powered loudspeaker is equipped with an integrated two-channel amplifier
module driving the high frequency and low frequency components independently, taking
consistent performance, convenience and ease of use to a new level. Milan eliminates the need for
separate amplifier racks and controllers, as well as the attendant cabling. This makes setting up at
gigs and obtaining a consistent sound in different venues a faster and simpler process.
The amplifiers are exactly matched to the known parameters of the loudspeaker components, and
are therefore able to produce the optimum power for the drivers. By placing the amplifiers in the
cabinet it is possible to keep the loudspeaker cables extremely short to eliminate resistive losses,
so effectively all the power from the amplifiers is transferred to the drivers.
The on-board electronics provides a mic and line input with two band EQ. Fast-acting limiters
allow you to achieve higher average sound pressure level, reduce the possibility of driver damage,
and help to ensure better long-term system reliability.
Using Milan Mi0 with Subwoofers
Improved bass response and higher overall sound pressure level can be achieved by adding sub-
bass loudspeakers to the Milan system. This also reduces mechanical stress on the Milan
loudspeaker’s low frequency driver, since most of the low frequency content in the signal is routed
to the subwoofer.
It is recommended that you connect the full range signal from the mixer first to the subwoofer(s),
and from there to the Milan Mi0.
Using Milan Mi0 as a Floor Monitor
Reduce the level of the BASS CONTROL when using Milan as a floor monitor, which will avoid any
low frequency boominess due to the proximity of the floor that can detract from clear and
intelligible monitor sound.
If you are using Milan as part of a larger multi-channel monitor system and where drums may be
part of the monitor mix, it is recommended that kick drum EQ is used sparingly and carefully.
MILAN Mi0 user manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Model Information
Milan Mi0 Self-Powered Loudspeaker
The Milan Mi0 is a self-powered sound reinforcement loudspeaker designed for many different
portable and permanently installed applications.
It consists of a custom 10” low frequency driver, matched
with a 1” high frequency compression driver on a 90°
horizontal x 60° vertical Converging Elliptical Waveguide
providing smooth and even coverage over a wide audience
area, together with a two channel amplifier module
providing microphone and line level input channels and
equalisation.
These high quality professional components are housed in
a lightweight, stylish and durable trapezoidal moulded
polypropylene cabinet that is instantly adaptable to front-
of-house or floor monitoring applications. The cabinet is
extensively ribbed and internally damped. This design
feature increases the cabinet’s rigidity and eliminates
internal reflections, which translates into better transient
response and improved bass reproduction. It also keeps
the weight of the cabinet as low as possible.
Mi0 is equipped with a dual angle pole mount socket which
allows it to be angled down for better coverage when used
with tripod stands or for mounting on top of bass cabinets. Lifting and carrying is made easy with
the provision of a comfortable scoop handle on the top of the cabinet.
The Mi0 cabinet provides M10 rigging points on the top and bottom for suspending horizontally or
vertically in permanent installs.
MILAN Mi0 user manual
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Milan Mi0 Features
Two discrete amplifier channels: 360 watts (program) Class D low frequency and 100
watts (program) Class AB high frequency for excellent audio quality
Integrated mixer provides XLR microphone input and line input on combination jack/XLR
connector
Two-band EQ with 6dB of cut and boost
Mix Out function allows daisy-chaining of Milan loudspeakers and simple expansion of
your sound system
Trapezoidal shape with symmetrical 43° wedge angle allows the loudspeaker to be used
as a floor monitor
Ergonomically placed handle for easy lifting and carrying
Professional quality 1” high frequency compression driver with wide dispersion
Converging Elliptical Waveguide
Custom developed 10” LF driver provides high performance and contributes to lower
weight
Dual angle pole mount socket allows the loudspeaker to be used vertically or angled
downwards for improved coverage
Durable, stylish and lightweight moulded composite enclosure
Internal M10 rigging points on top and bottom for easy suspension in permanent installs
Attractive powder coated and galvanised perforated steel grille
MILAN Mi0 user manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Connector wiring
The amplifier microphone and line inputs are designed to accept balanced (three conductor)
connections, and it is recommended that this method be used since it offers the best rejection of
noise, hum and radio interference, especially where long cable runs are involved. XLR connectors
should be wired pin 2 hot (positive), pin 3 cold (negative) and pin 1 ground, while the standard
wiring for 3-pole jack plug connectors is tip hot (positive), ring cold (negative) and sleeve ground
as shown below.
ground
cold
hot
cold
ground
hot
Balanced male XLR
Balanced female XLR
Some signal sources such as keyboards, acoustic guitars with on-board electronics commonly
provide only an unbalanced output on a 2-pole jack connector. The Milan loudspeaker line input
can handle these connections without any rewiring since pin 3 (-ve) of the input is automatically
grounded by the jack plug.
tip - hot
tip - hot
cold
ring - cold
ground
sleeve - ground
3-pole jack (balanced)
2-pole Jack (unbalanced)
If an unbalanced source is to be connected to an input channel via the XLR line input connector,
either 2-pole or 3-pole jack plugs can be used. In both cases pin 3 should be connected to pin 1
(ground) at the XLR as shown here.
1 (ground)
2
3
tip
ring
sleeve
1 (ground)
2
3
tip
sleeve
Some sources such as mp3 players or CD players commonly provide 2-pole unbalanced phono
connectors, and these can be connected to the Milan line input channel via either the XLR
connector or jack connector. In either case wire the connectors as follows:
1 (ground)
2
3
tip
sleeve
tip
tip
sleeve
sleeve
MILAN Mi0 user manual
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Connecting to the Milan Mi0
8
12
11 10
9
7
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE
LINE LEVEL
4
3
6
5
GROUND LIFT
POWER
MIC IN
MIX OUT
LINE IN
2
ON
1
1. Mains Connector and Fuseholder
Mains power is connected to the loudspeaker via a combination IEC connector and fuseholder.
Make sure that the Milan Mi0 loudspeaker is turned off before connecting mains power. Replace
the fuse only with the same type and rating.
2. Mains Switch
Rocker switch turns mains power on to the loudspeaker. Make sure the Mic Gain and Line Level
controls are fully off (MIN) and power up other external equipment such as a mixer before
switching on.
3. Ground Lift switch
Safely lifts the signal ground of the balanced audio inputs from the ground of the amplifier. Select
position as appropriate in order to minimise hum.
4. Microphone Input
Balanced female XLR connector for use with a variety of balanced and unbalanced dynamic
microphones. The mic input is not suitable for condenser microphones that require phantom
power. The input is balanced to avoid hum loops and RF interference, and is wired pin 2 hot, pin 3
cold.
MILAN Mi0 user manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
5. Line Level Input
Combination jack/XLR connector that will accept a wide range of balanced and unbalanced line
level sources such as keyboards, acoustic guitars with on-board electronics and other line level
sources such as CD players and DJ mixers.
6. Mix Out
An unbalanced line level output on a male XLR that connects to additional powered Milan
loudspeakers. This output contains a mix of all connected sources and is post-EQ. Note that
adjusting the equalisation will similarly affect any additional Milan loudspeakers connected from
this output.
7. Line Level Control
Rotary level control which attenuates the input signal level of the connected instrument / line
source.
8. Treble Control and 9. Bass control
The bass control provides 6dB of boost or cut at 90H with a shelving curve shape, and the treble
control provides 6dB of boost or cut at 8kHz with a shelving curve shape. Always use equalisation
sparingly, aiming to cut rather than boost especially when the loudspeaker is used near
boundaries such as walls or floors.
10. Mic Gain Control
Rotary level control which attenuates the input signal level of the connected microphone. Allows
the mic signal to be optimised for the first and subsequent loudspeakers connected to the MIX
OUT connector.
11. Limit Indicator
Illuminates green to indicate the presence of signal at the amplifier input. Illuminates red when the
amplifier’s output is limited. Frequent and/or continuous lighting of the limit LED indicates
overdriving. If this occurs reduce the input level to the loudspeaker or enlarge your system with
additional loudspeakers.
12. Power Indicator
Illuminates green to indicate that mains power is connected and powered up.
MILAN Mi0 user manual
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Connection Diagrams
Small duo setup using the integrated mixer and Mix Out
The built in two channel mixer allows the simultaneous use of a low impedance dynamic
microphone and a line level source. The line level source could be an acoustic instrument such as
a guitar with either passive or active on-board electrics, a keyboard, or MP3 player. Connect
dynamic microphones directly to the mic input connector, and adjust the volume level. Connect
line sources to the combo jack/XLR connector and adjust the volume control. Use the MIX OUT
function to daisy-chain to additional Milan loudspeakers.
MIN
MAX
-
+
-
+
MIN
MAX
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
ON
ON
DI box
MILAN Mi0 user manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Stereo PA with an external mixer
Two Milan loudspeakers form the left and right elements of a stereo PA setup with all signal
sources connected to an external mixing console. Connect the outputs of the mixer to the Mi0 line
inputs using either balanced XLR cables, or balanced or unbalanced jack cables. Bring up the
master faders on the mixer, ensuring that the outputs are not clipping, and then adjust both
loudspeakers’ level controls to the desired loudness. For consistent balance and response set the
tone controls to approximately the same positions on both cabinets.
LEFT
RIGHT
MIN
MAX
-
+
-
+
MIN
MAX
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
ON
ON
MILAN Mi0 user manual
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Stereo PA with an external mixer and subwoofers
In this example, sub frequencies are routed to separate subwoofers in order to gain extended
frequency response and higher overall sound level. Connect the mixer output first to the
subwoofers and then loop up to the Milan loudspeakers. Connect the outputs of the subwoofers to
the Mi0 line inputs using either balanced XLR cables, or balanced or unbalanced jack cables. The
tone controls on both cabinets should be set to the same positions, nominally flat to begin with.
Ensure that the mixer outputs are not clipping, and then adjust both loudspeakers’ level controls
to the desired loudness.
MIN
MAX
-
+
-
+
MIN
MAX
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
ON
ON
MILAN Mi0 user manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Stereo PA with powered wedge monitors
On larger gigs a separate monitor system provides good quality foldback for individual performers
and helps to keep the PA sound less cluttered.
LEFT
RIGHT
MIN
MAX
-
+
-
+
MIN
MAX
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
ON
ON
MIN
MAX
-
+
-
+
MIN
MAX
MIN
MAX
-
+
-
+
MIN
MAX
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
ON LIMIT MIC GAIN
BASS
TREBLE LINE LEVEL
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
GROUND LIFT MIC IN
POWER
MIX OUT
LINE IN
ON
ON
MON 1
MON 2
MILAN Mi0 user manual
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Loudspeaker Placement
In order to avoid the possibility of feedback locate the loudspeakers in front of your microphones
and do not point microphones directly at the front of a loudspeaker.
When using speaker stands, try to raise the loudspeakers as high as practically possible (at least
higher than the heads of the audience) since people are very good absorbers of sound, especially
at high frequencies. You also have the option to point them down using
the alternate angle provided for by the built-in dual angle pole holder.
Doing this will improve the coverage for
both near and far audience members.
SAFETY PRECAUTIONS: make sure that
any speaker stands you use are capable of
taking the weight of the loudspeaker, and
that stands are placed on a flat, level and
stable surface. Make sure that the legs do
not present a trip hazard. Take care when
lifting the speakers on to the stand; ask
someone else to help you if needed.
The same applies to using Milan
loudspeakers mounted on straight poles on
top of bass cabinets or subwoofers.
Adjustable height poles or stands allow you
to fine tune the height of the loudspeakers
to suit your venue.
Do not place your loudspeakers too close to
turntables as this may induce rumble or
low frequency feedback from the tone
arms. Isolate turntables on shock mounts.
Use equalisation sparingly. Start with the
bass and treble controls at their neutral
position (no boost or cut). Cut a little bass
to tame any boomy frequencies in the
room, and add a little treble to help vocal
intelligibility.
Consider adding subwoofers and/or further loudspeakers if the overall sound level or low
frequency response is not enough for the room.
MILAN Mi0 user manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Installing the Milan loudspeaker
Using the M10 rigging points
The Milan loudspeaker can be permanently installed in a venue, suspended
from eyebolts fitted to the internal M10 rigging points on the top and bottom
of the cabinet. Three possible orientations are available: vertically upright, or
upside down to position the high frequency driver closer to the audience, or
sideways if required.
Insert M10 load-rated shoulder eyebolts into the
threaded rigging points and tighten. The front
rigging points should take the majority of the load
while the rear rigging point should be used for
angling the cabinet downwards only.
When installing the
cabinet sideways, pick
up from either of the
two front eyebolt
pairs, and bridle the
two rear eyebolt points to provide a single pull-
back for adjusting the downward angle.
Wall Mounting
The Milan loudspeaker can be conveniently wall mounted using the PB-55 pole mount wall
bracket, which simply locates into the pole mount socket in the bottom of the cabinet.
Mount the bracket to the wall using suitable fixings, and locate the loudspeaker onto the pole
mount bracket. Rotate and angle the loudspeaker to optimise coverage and tighten the locking
mechanism to stop the loudspeaker from being inadvertently removed.
MILAN Mi0 user manual
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Troubleshooting
Fault
Check
Action
No power to the
loudspeaker
Is the mains lead plugged in?
Connect the mains lead
Is the mains outlet live?
Is the power switch on?
Check the mains outlet or switch to
another outlet
Press the mains switch
No sound / quiet sound
Are the level controls turned
down (anti-clockwise)?
Turn the control slowly clockwise
Is the source sending a signal? Verify signal at the source output.
Un-mute muted outputs or mixer
channels. Check cables and replace
No sound from
Is the microphone a
condenser type needing
phantom power?
Milan does not supply +48v
phantom power. Use a dynamic
microphone or connect to a mixer
with phantom power
connected microphone
No sound although
loudspeaker is on
Is the loudspeaker in protect
mode?
Turn off the mains switch, unplug
the loudspeaker before
reconnecting
Does the loudspeaker remain
in protect mode?
Refer to qualified service personnel
Reduce mixer or preamp level
Distorted sound
Is the input signal level too
high?
Is the mic/line switch set
incorrectly?
Change mic/line setting to correct
source
Distorted sound, limit
LED is on continuously
Are the level controls set too
high?
Reduce volume controls or use
additional loudspeakers
Hum or noise
Are the connected sources
balanced?
Use balanced cables and 3-pole
connectors wherever possible.
Check wiring.
Ground loops?
Lift audio ground on affected
device with adapter
Are signal cables near or
running parallel to mains
cables?
Move signal cables
MILAN Mi0 user manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Product Dimensions
Milan Mi0
MILAN Mi0 user manual
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Technical Specifications
Milan Mi0
Dimensions
515mmH x 330mmW x 293mmD
(20.3” x 13” x 11.5”)
Net weight
11.8kg (26lbs)
Frequency range
Dispersion
55Hz – 20kHz ±3dB
90°H x 60°V @ -6dB points
119dB/125dB
Max SPL (cont/max)
Construction
Injection-moulded polypropylene enclosure, self-coloured in
dark blue. Recessed carrying handle. Integral dual-angle pole
mount socket. Powder coated galvanised perforated steel
mesh grille
Connectors
Controls
Mic input: female XLR wired pin 2 hot
Line input: combo jack/female XLR wired pin 2 hot
Mix out: XLR male wired pin 2 hot
IEC mains conector with integrated fuseholder
Mic gain
Line level
Mains on/off
Bass and treble controls
Ground lift switch
Indicators
SIG/LIMIT LED
Power LED (green)
Rigging options
6 x M10 threaded internal rigging points
MILAN Mi0 user manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Spare Parts
Stock Code
LS1029.2
05B1095
04A9340
05B9332
16F466
Model
Description
LS-1029.2
RC-1029
10” (254mm) low frequency driver
Recone kit
CD-122
HF compression driver
Replacement HF diaphragm
Replacement amplifier assembly
RD-122
AMP ASSEMBLY
Accessories
Stock Code
07B508/0.6
07B508
Model
PA-60
Description
Speaker pole 35mm x 60cm long
Speaker pole 35mm x 90cm long
Speaker pole 35mm x 100cm long
Speaker pole 35mm x 120cm long
Pole mount wall bracket
PA-90
07B508/1.0
07B508/1.2
07B830
PA-100
PA-120
PB-55
07B392
EB-10/18
M10 shoulder eyebolt
MILAN Mi0 user manual
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Warranty
All products in this manual are warranted by Turbosound Limited to the original end-user
purchaser against defects in workmanship and materials used in its manufacture for a period of
two (2) years for loudspeakers and one (1) year for electronics from the date of shipment to the
end user.
Faults arising from misuse, unauthorised modifications or accidents are not covered by this
warranty. No other warranty is expressed or implied.
This warranty does not affect any statutory rights of the purchaser.
Should any fault develop with a component of your Turbosound system the faulty unit should be
sent, in its original packaging, to the supplier or your local authorised Turbosound dealer with the
shipping prepaid.
You should include a written statement listing the faults found, and the product serial number
must be quoted ion all correspondence relating to the claim.
IMPORTANT: We recommend you record your purchase information here for future reference.
Dealers Name: ..................................................................................................................................
Address: ............................................................................................................................................
............................................................................................................................................................
............................................................................................................................................................
Phone No: .........................................................................................................................................
Invoice/Receipt No./Date . ...............................................................................................................
Serial number: ..................................................................................................................................
In keeping with our policy of continual improvement, Turbosound Limited reserves the right to
alter specifications without prior notice.
MILAN Mi0 user manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
user manual
MILAN Mi0
Contact Information
Turbosound Ltd
Star Road
Partridge Green
West Sussex RH13 8RY
United Kingdom
Customer Service
If your product requires servicing please contact your local distributor or retailer. A complete list is
available on our website at:
Product Information
You can find full details on all our products on the internet at:
MILAN Mi0 user manual
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
|