True Manufacturing Company Beverage Dispenser GDM 26 User Manual

ELSTAT TRAINING BOOKLET  
GDM SERIES COOLER EQUIPPED WITH EMS (ELSTAT) CONTROL  
GDM-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELSTAT SEQUENCE OF OPERATION  
Once the cabinet is plugged in, the ELSTAT control will flash "888" and then  
go through a parameter check. Once completed, the control will do a "soft  
start". Lights come on first, approximately 30 seconds later the compressor  
will start. Approximately 30 seconds from the compressor start up, the evap  
motor will start. The control will display "Use". The control will then cycle  
the compressor on and off at the predetermined temp (Model specific).  
The whole time the controller is on it is learning the customer traffic. Once  
enough data has been accumulated the controller will now cycle between  
two modes. "Standby" and "Use". In the standby mode the controller  
predicts that customer traffic is nonexistent. It will display (---). It cycles the  
compressor to hold about 50˚F. It shuts the lights off and cycles the evap  
fan motor. It will hold this pattern until roughly 2 hours before customer  
traffic is predicted to start. The controller will then switch into the "use"  
mode. Cycling the compressor on and off based on temperature (Approx  
36˚F to 38˚F product temp). Running lights continuously. The controller will  
then cycle between these two modes.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
&-45"5ꢃ$0.10/&/54  
Controller  
Transformer  
Probe  
Evaporator Fan  
Evaporator Fan  
Evaporator Coil  
Evaporator Coil  
Airflow  
Airflow  
Elstat  
Elstat  
Probe Location 1  
Probe Location 2  
GDM-10 through GDM-37  
Probe is in return air mounted by the evaporator fan motor.  
GDM-45 to GDM-72  
Probe is in the discharge air stream  
Off of the Evaporator Coil  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
'30/5ꢃ7*&8ꢃ0'ꢃ&-45"5  
Perishable Mode Light  
Waterdrops  
Snowflake  
Up/Down Key  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
3&"3ꢃ7*&8ꢃ0'ꢃ$0/530--&3  
ꢂꢅ  
ꢀꢅ  
ꢇꢅ  
ꢈꢅ  
ꢊꢅ  
ꢆꢅ  
ꢌꢅ  
ꢉꢅ  
ꢍꢅ  
/0ꢅ /".&  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
Line In  
Lights  
Not Used  
Appliance Sensor  
Compressor  
Fan (s)  
12 Vac  
Not Used  
Not Used  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
FREQUENTLY ASKED QUESTIONS  
$BOꢃUIFꢃ&MTUBUꢃDPNFꢃPVUꢃPGꢃUIFꢃꢎ4UBOEꢃCZꢎꢃNPEFꢃCFGPSFꢃJUTꢃQSFEFUFSNJOFEꢃUJNF  
/Pꢅ If the motion sensor is set off during the "Stand by" mode the control will automatically  
turn the lights on, however it will stay in stand by mode.  
$BOꢃUIFꢃ&MTUBUꢃCFꢃTFUꢃVQꢃGPSꢃDPOUJOVPVTꢃVTFꢃBOEꢃꢃOPUꢃHPꢃJOUPꢃUIFꢃꢎ4UBOEꢃCZꢎꢃNPEF  
:FTꢅ The control can be set into perishable mode. This would shut down the "stand by"  
mode. The lights will still cycle (like stand by mode) when cabinet doesn't see activity.  
/05&ꢌꢀ5IFSFꢀJTꢀOPꢀBCJMJUZꢀUPꢀTFUꢀMJHIUTꢀPOꢀBMMꢀUIFꢀUJNFꢇ  
$BOꢃMJHIUTꢃCFꢃTFUꢃUPꢃTUBZꢃPOꢃBUꢃBMMꢃUJNFT  
/Pꢅ Elstat controller does not have this capability. Lights will always turn off in "stand by"  
Mode.  
)PXꢃEPꢃ*ꢃQVUꢃDPOUSPMMFSꢃJOUPꢃ1FSJTIBCMFꢃNPEF ꢃ  
tꢀꢀ1FSJTIBCMFꢀNPEFꢀJTꢀVTFEꢀXIFOꢀBOZUIJOHꢀQFSJTIBCMFꢀJTꢀCFJOHꢀTUPSFEꢀJOꢀUIFꢀDBCJOFUꢇ  
tꢀꢀ*OꢀQFSJTIBCMFꢀNPEFꢈꢀDBCJOFUꢀXJMMꢀNBJOUBJOꢀBꢀꢂꢉ¡'ꢊꢂꢋ¡'ꢀQSPEVDUꢀUFNQFSBUVSFꢇꢀ5IFꢀ  
cabinet will not go into standby mode.  
/05&ꢌꢀ"MMꢀ&OFSHZꢀ4UBSꢀDBCJOFUTꢀBSFꢀTIJQQFEꢀJOꢀQFSJTIBCMFꢀNPEF  
t1SFTTꢀUIFꢀTFUꢀCVUUPOꢀLFZꢀ MPPLTꢀMJLFꢀBꢀTOPXꢀGMBLFꢁꢌꢀUIFꢀTDSFFOꢀTIPVMEꢀTIPXꢀ1"4  
tꢀꢀ:PVꢀXJMMꢀOPXꢀOFFEꢀUPꢀFOUFSꢀUIFꢀLFZꢀEBODFꢌꢀ  
tꢀꢀ1SFTTꢀUIFꢀTOPXꢀGMBLFꢀLFZꢀꢂꢀCFFQT  
tꢀꢀ1SFTTꢀUIFꢀVQꢀBSSPXꢀLFZꢀꢃꢀCFFQT  
tꢀꢀ1SFTTꢀUIFꢀEPXOꢀBSSPXꢀLFZꢄꢀCFFQ  
tꢀꢀ1SFTTꢀUIFꢀXBUFSꢀESPQTꢀLFZꢀꢅꢀCFFQTꢀ TIPVMEꢀTIPXꢀEJTQMBZꢀPGꢀꢆ14ꢆꢁ  
tꢀꢀ/PXꢀQSFTTꢀBOEꢀIPMEꢀEPXOꢀUIFꢀTOPXꢀGMBLFꢀLFZꢀVOUJMꢀUIFꢀTDSFFOꢀTIPXTꢀ1&SꢀBOEꢀꢍꢍꢇ  
tꢀꢀ/FYUꢀQSFTTꢀBOEꢀIPMEꢀUIFꢀVQꢀBSSPXꢀLFZꢀVOUJMꢀUIFꢀTDSFFOꢀTIPXTꢀ1&SꢀBOEꢀꢍꢄꢇ  
tꢀꢀ8BJUꢀVOUJMꢀDPOUSPMMFSꢀSFBETꢀꢆ64&ꢆꢎꢀVOQMVHꢀUIFꢀDBCJOFUꢀBOEꢀQMVHꢀJUꢀCBDLꢀJOꢇꢀ"UꢀUIJTꢀꢀ  
point the red LED in center of the control should be “onwhich means that the  
control is in perishable mode.  
)PXꢃEPꢃ*ꢃQFSGPSNꢃBꢃ)BMGꢃSFTFUꢄꢃBOEꢃXIBUꢃJTꢃJU  Half reset clears any of the learning memory.  
tꢀꢀ1VTIꢀUIFꢀTFUꢀCVUUPOꢀLFZꢀ MPPLTꢀMJLFꢀBꢀTOPXꢀGMBLFꢁꢀUIFꢀTDSFFOꢀTIPVMEꢀTIPXꢀ1"4  
tꢀꢀ:PVꢀXJMMꢀOPXꢀOFFEꢀUPꢀFOUFSꢀUIFꢀLFZꢀEBODF  
tꢀꢀ1SFTTꢀUIFꢀTOPXꢀGMBLFꢀLFZꢀꢂꢀCFFQT  
tꢀꢀ1SFTTꢀUIFꢀVQꢀBSSPXꢀLFZꢀꢃꢀCFFQT  
tꢀꢀ1SFTTꢀUIFꢀEPXOꢀBSSPXꢀLFZꢄꢀCFFQ  
tꢀꢀ1SFTTꢀUIFꢀXBUFSꢀESPQTꢀLFZꢅꢀCFFQTꢀ TIPVMEꢀTIPXꢀEJTQMBZꢀPGꢀꢆ14ꢆꢁ  
tꢀꢀ1SFTTꢀBOEꢀIPMEꢀUIFꢀEPXOꢀBSSPXꢀLFZꢀVOUJMꢀZPVꢀWJFXꢀ)3  
tꢀꢀ1SFTTꢀUIFꢀTOPXꢀGMBLFꢀLFZꢀ EJTQMBZꢀTIPVMEꢀTIPXꢀ1"4ꢁ  
tꢀꢀ3FꢀFOUFSꢀLFZꢀEBODFꢀBOEꢀUIFꢀ)BMGꢀ3FTFUꢀJTꢀDPNQMFUFꢇ  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
/03."-ꢃ01&3"5*/(ꢃ$0%&4  
Normal operating mode. Cabinet  
should be holding proper product  
temperature.  
Units is in Standby mode. Control  
will cycle the unit at a warmer  
temperature. Lights will be off.  
Units is in defrost . Compressor has  
been shut off and evaporator fan  
motor is running to clear any ice  
that may have accumulated. This is a  
predetermined program function.  
'"6-5ꢃ$0%&4ꢏꢃ5306#-&4)005*/(  
Freeze up protection. This unit has  
gone down below the minimum  
temperature Set Point.  
Refrigeration System Failure. The unit  
has not satisfied the set point in the  
amount of time allowed.  
1PTTJCMFꢃ1SPCMFNT  
"DUJPOꢃUPꢃUBLF  
1PTTJCMFꢃ1SPCMFNT  
Unit is not cooling  
Faulty Probe  
"DUJPOꢃUPꢃUBLF  
Compressor not shutting off  
Check compressor. Relay at  
controller  
Check the Refrigeration System  
Ohm out evaporator probe  
Faulty Probe  
Ohm out evaporator probe  
Check parameter list  
Faulty Controller  
Bypass control to see if system will  
run  
Parameters have been  
changed  
Parameters have been  
changed  
Check the parameter list  
Power supply voltage is low.  
Power supply voltage is too high.  
1PTTJCMFꢃ1SPCMFNT  
High voltage at outlet  
Faulty Transformer  
"DUJPOꢃUPꢃUBLF  
1PTTJCMFꢃ1SPCMFNT  
Poor voltage at outlet  
Faulty Transformer  
"DUJPOꢃUPꢃUBLF  
Verify proper voltage to cabinet  
Verify proper voltage to cabinet  
Verify 120V to transformer. Check for  
12V on secondary. Connector 7  
(see page 2)  
Verify 120V to transformer. Check for  
12V on secondary. Connector 7  
(see page 2)  
Faulty Elstat  
If 12V is present at connector 7, replace  
Elstat.  
Faulty Controller  
Faulty Elstat  
Bypass control to see if system will run  
If 12V is present at connector 7, replace  
Elstat  
Probe failure  
Elstat Probes by the evaporator motor GDM-10 to 33 probes in air  
stream GDM-35 to 72  
1PTTJCMFꢃ1SPCMFNT  
"DUJPOꢃUPꢃUBLF  
7BMVF  
ꢂꢃ¡  
0INT  
Connector off at controller Verify that connector 4 is in place  
(see page 2)  
32,000 Ohms  
12,000 Ohms  
9,300 Ohms  
8,500 Ohms  
7,000 Ohms  
ꢏꢍ¡  
Probe is open  
Ohm out probe  
ꢋꢍ¡  
Probe is shorted  
Probe wire is open  
Ohm out probe  
ꢋꢐ¡  
Ohm out probe wire  
ꢑꢍ¡  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
(%.ꢃ4&3*&4ꢃ$00-&3ꢃ&26*11&%ꢃ8*5)ꢃ&.4ꢃ &-45"5ꢋꢃ$0/530-  
5306#-&4)005*/(ꢃ(6*%&  
5306#-&4)005*/(ꢃ(6*%&  
(Please note this does not cover any and all situations)  
$PNQMBJOU  
1PTTJCMFꢃ$BVTF  
3FQBJS  
$BCJOFUꢃOPUꢃDPMEꢃFOPVHI  
1. No product in cabinet.  
1. Load cabinet Elstat is  
equipped with a anti-short  
cycle that can make the unit  
run warm with no product.  
2. Unit in a unpredictable  
2. Move cabinet or put into  
location. Elstat control may be Perishable mode.  
going in standby mode.  
3. Unit was in a previous  
location.  
3. Perform half reset.  
8BSNꢃ1SPEVDU  
1. Unit in a unpredictable  
location. Elstat control may be Perishable mode.  
going into standby mode.  
1. Move cabinet or put into  
2. Compressor not running.  
3. Compressor running.  
4. Unit in standby mode.  
2. Check for out put voltage  
at controller. If good follow  
compressor diagnosis.  
3. Follow refrigeration trouble  
shooting guides.  
6OJUꢃEJTQMBZJOHꢃBꢃ  
UFNQFSBUVSFꢃJOTUFBEꢃPGꢃꢃ  
iVTFw  
1. Unit recently worked  
on. Parameters have been  
changed.  
1. Reset the DIS parameter to  
“0.  
ꢀꢁꢁꢂꢃ&BTUꢃ5FSSBꢃ-BOFꢃtꢃ0h'BMMPOꢄꢃ.0ꢅꢃꢆꢇꢇꢆꢆꢃtꢃQIꢅꢃꢆꢇꢆꢅꢀꢈꢁꢅꢀꢈꢁꢁꢃtꢃUPMMꢃGSFFꢃꢉꢁꢁꢅꢃꢇꢀꢊꢅꢆꢂꢊꢀꢃtꢃTFSWJDF!USVFNGHꢅDPNꢃ  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  

Taylor Freezer C712 User Manual
Tech Craft TV Video Accessories MC6032B User Manual
Texas Memory Systems Computer Hardware XP 15 User Manual
Tiger Games 060 021 User Manual
Toastmaster Convection Oven TCOV6RCAN User Manual
Toshiba DVD Player SD P2900 User Manual
Toyota Automobile xB User Manual
Tripp Lite Surge Protector SPS Series User Manual
Viking Electronics Answering Machine MLC 24 User Manual
VTech Telephone VT1121 User Manual