Owner’s Manual
Monitored PDU
Zero U (Vertical) Format
*
*CE logo applies to models with IEC power inlet.
Important Safety Instructions
2
2
Installation
Features
6
Configuration and Operation
Technical Support
Warranty and Warranty Registration
Español
8
8
9
10
19
Français
1111 W. 35th Street • Chicago, IL 60609 USA
Copyright © 2009 Tripp Lite. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
continued
Connecting the PDU
2-1 (Models with IEC power inlet only.) Select
models have a detachable power cord. Attach the
included power cord to the PDU by inserting the
C
A
A
IEC connector of the power cord into the IEC
B
power inlet located near the end of the PDU.
C
Use the included bracket to secure the power
cord connection.
Note: Optionally, a user-supplied power cord can be attached to the
PDU by connecting it to the IEC inlet. Do not attempt to attach a
user-supplied power cord unless it is certified to be compatible with
the input power source that will be used by the PDU.
B
2-1
A
2-2 (Optional - models with input plug adapter
only.) Select models include an input plug
adapter that converts the twist-lock input plug
to a straight-blade input plug. Attach the input
B
A
B
plug adapter
to the input plug if you wish
to plug the PDU into a compatible straight-
blade outlet.
2-2
2-3 Connect the input plug to a compatible AC
power outlet. If the PDU does not have a circuit
breaker, it should be provided with a branch-
rated over-current protection device that
matches the rated amperage of the PDU.
Note: The AC power source should not share a circuit with a
heavy electrical load.
2-3
A
2-4 Connect your equipment's input plugs
B
B
to the outlets of the PDU. The digital load
C
meter displays the total connected equipment
load in amps. (Select models provide additional
load data. See the Features section for more
A
information.)
Note: In order to minimize interference among connected
devices, connect each device to the nearest PDU outlet and coil
excess power cord length.
C
2-4
2-5 (Optional) If you attached the cord
retention bracket(s), tie each equipment power
cord to the retention bracket. Attach each cord
to the retention shelf by looping the cord and
securing it with one of the included cable ties
A
A
. Make sure that each cord can be unplugged
from the PDU without removing the cable tie.
2-5
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
continued
Networking the PDU
Note: The MAC address of the PDU (a 12-digit string in this format: 000667xxxxxx) is printed on a label attached to the PDU
enclosure. The MAC address is also printed on a label attached to the internal network card.
3-1
If your network's DHCP server will assign a dynamic IP address to the PDU automatically, go to Step
If you will assign a static IP address to the PDU manually, go to Step 4-1 . If you are uncertain which
.
method to use, contact your network administrator for assistance before continuing the installation process.
Dynamic IP Address Assignment
3-1 Connect PDU to Network: While the PDU is powered, connect a
A
standard Ethernet patch cable to the RJ-45 Ethernet port on the PDU.
Note: This port is not compatible with PoE (Power over Ethernet) applications.
The PDU will attempt to obtain an IP address via DHCP. This may take
as long as several minutes, depending on your network environment.
A
3-1
3-2 Discover IP Address: Contact your network administrator to
determine which dynamic IP address has been assigned to the PDU by
the DHCP server. The PDU can be identified on the DHCP server by referring to its MAC address.
(The MAC address is a 12-digit string in this format: 000667xxxxxx. Refer to the MAC address label
attached to the PDU.) You may wish to request a long-term lease period for the IP address, depending
4-1
4-6
on your application. After you have discovered the IP address, skip Steps
through
and proceed
5-1
directly to Step
.
Static IP Address Assignment
4-1 Determine IP Information: Before assigning a static IP address, you'll need to know the IP
address, gateway address and subnet mask. If you do not have this information, contact your network
administrator for assistance.
4-2 Configure Terminal Emulation Program: Open a VT100-compatible terminal emulation
program (such as the HyperTerminal program bundled with Microsoft® Windows®) on a computer
with an available DB9 serial port. (A notebook computer may be the most convenient choice.) Set the
terminal emulation program to use the COM port that corresponds to the computer’s DB9 serial port.
Specify the parameters required to communicate with the PDU terminal interface:
If the terminal emulation program supports multiple emulation modes, you may also need to specify
VT100 emulation.
Bits per second:
Data bits:
Parity:
9600
8
None
Stop bits:
Flow control:
1
None
4-3 Connect PDU to Computer: Use the mini-
DIN to DB9 serial cable (part number 73-1025)
included with the PDU to connect the PDU to
A
A
B
the computer. The circular connector at one
C
end of the cable attaches to the 8-pin mini-DIN
B
serial port on the PDU. (Align the connector
carefully to avoid damaging the pins.) The DB9
D
4-3
C
connector at the other end of the cable
D
connects to the computer's serial port
.
4-4 Connect PDU to Network: While the PDU
is powered, connect a standard Ethernet patch
A
A
cable to the RJ-45 Ethernet port on the PDU.
Note: This port is not compatible with PoE (Power over
Ethernet) applications.
4-4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
continued
Networking the PDU continued
4-5 Configure PDU in Terminal Mode: After a
brief pause, an initialization page should appear in
the terminal emulation program. Press any key on
the keyboard within 10 seconds to change the
PDU settings. (If the 10-second period has
elapsed, you can reboot the PDU by powering
down completely and then restoring power.)
Follow the sequence of responses below in order
to assign an IP address to the PDU. The default
terminal mode root password is TrippLite. Sample
IP settings are shown - supply your own IP
information when you configure your PDU.
4-5
Press A to Accept the settings, or M to Modify? M
Enter the root password: *********
Reset configuration to default values (Y/N)? N
For each of the following questions, you can press <Return> to select the value shown in
braces, or you can enter a new value.
NETWORK INTERFACE PARAMETERS:
Should this target obtain IP settings from the network?[N] N
Static IP address [192.168.1.19]? 192.168.0.123
Static IP address is 192.168.0.123
Subnet Mask IP address [255.255.0.0]? 255.255.255.0
Subnet Mask IP address is 255.255.255.0
Gateway address IP address [192.168.1.1]? 192.168.0.1
Gateway address IP address is 192.168.0.1
You can also change the root password, real-time clock and other settings. (Tripp Lite recommends
against changing the default settings unless you are an advanced user with a specific purpose.) After you
have finished entering settings, the PDU will save changes to memory and reboot (this may take several
minutes). After the PDU reboots, the initialization page should display the new static IP settings.
5-1
4-6 Remove Serial Cable: Remove the serial cable from the PDU and proceed to Step
.
Testing Network Connection
5-1 Access PDU with Web Browser: After an
IP address has been assigned to the PDU,
attempt to access it with a Web browser that
™
supports frames, forms and Java . Open a Web
browser on a computer connected to the LAN
and enter the IP address assigned to the PDU.
A
You should be prompted for a password . The
user name is admin and the default password is
admin. After you enter the user name and
A
B
password, the PowerAlert status page
appear in the browser window. For more
will
information about configuration and operation of
the PDU via the PowerAlert interface, refer to
the SNMPWEBCARD User's Guide, included
on the CD-ROM bundled with the PDU.
Note for Network Management System Users Only: Two MIB
files - Tripplite.mib and RFC1628.mib - must be loaded on each
Network Management Station that will monitor the PDU via
SNMP. The files are provided on the CD-ROM included in the
product package.
B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Input Plug Adapter (Select Models): Converts the twist-lock
input plug to a straight-blade input plug.
Power Inlet (Select Models): The IEC power inlet connects to
the included power cord or a compatible user-supplied power
cord. The inlet includes a bracket to secure the cord connection.
Outlets (Vary by Model): During normal operation, the outlets
distribute AC power to connected equipment.
IEC-60320-C13
IEC-60320-C19
NEMA 5-15/20R
Digital Load Meter (Ammeter): The total connected equipment
load is displayed on the meter in amperes. Models with
A
B
A
C
multiple outlet banks can also display the connected equipment
B
load for each outlet bank. Use the mode selection switch to
C
display the total load (all bank LEDs illuminated) or the load
for each outlet bank (corresponding bank LED illuminated).
Circuit Breaker (Select Models): If the connected equipment load
exceeds the Maximum Load Rating of the PDU, the circuit breaker
will trip. Disconnect excess equipment and allow the breaker to cool
before depressing the plunger to reset the breaker. Models with
multiple outlet banks have a circuit breaker for each bank.
Cord Retention Bracket: Provides secure attachment points for
connected equipment cords.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
continued
Mounting Brackets: Use these brackets to mount the PDU .
Mounting Buttons: Attach the included mounting buttons to the
PDU. Position the PDU as desired in the rack enclosure, align the
buttons with the rack mounting slots, and slide the PDU into
position.
Note: Regardless of configuration, the user must determine the fitness of hardware and
procedures before mounting. The PDU and included hardware are designed for common
rack and rack enclosure types and may not be appropriate for all applications.
A
SNMP Reset Button: Press the reset button for 3 seconds to
reboot the PDU's network card. Rebooting the network card will
not erase network settings or interrupt AC power.
A
Factory Port: The port is reserved for configuration by factory
authorized personnel only. Do not connect anything to the port.
PS/2 Port: Use this port to connect a Tripp Lite ENVIROSENSE
environmental sensor to provide remote temperature/humidity
monitoring and a dry contact interface to control and monitor
alarm, security and telecom devices. Contact Tripp Lite Customer
Support at 773.869.1234 for ordering information. Note: Do not
connect a keyboard or mouse to this port.
Mini-DIN Serial Port: Use this port to provide a direct terminal
connection to a computer with a terminal emulation program. A
serial cable (part number 73-1025) is included with the PDU. If
you need to order a replacement cable, contact Tripp Lite
Customer Support at 773.869.1234.
Ethernet Port: Use this RJ-45 jack to connect the PDU to the
A
network with a standard Ethernet patch cable. The Link LED
B
and Status LED indicate several operating conditions, as shown
in the table below. This port is not compatible with PoE (Power
Over Ethernet) applications.
B
A
Network Operating Conditions
A
Link LED Color
Off
No Network Connection
Flashing Amber
Flashing Green
100 Mbps Network Connection
10 Mbps Network Connection
B
Status LED Color
Off
Card Not Initialized
Steady Green
Flashing Amber
Card Initialized and Operational
Error - Card Not Initialized
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration and Operation
Remote Monitoring and Control
The PDU provides remote monitoring and more
via Web browser, telnet and SNMP-based
Network Management Systems. For more
information about configuration and operation
of the PDU via the PowerAlert Web browser
interface, refer to the SNMPWEBCARD User's
Guide, included on the CD-ROM bundled with
the PDU.
Technical Support
Telephone: 773.869.1233
8:00 AM - 6:00 PM CST Monday - Thursday
8:00 AM - 5:30 PM CST Friday
(CST is Central Standard Time in the United States.)
E-mail: [email protected]
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Warranty Registration
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material
and workmanship for a period of 2 years (except internal UPS system batteries outside USA and Canada, 1 year) from the
date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair
or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping
the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller
will pay return shipping charges. Call Tripp Lite Customer Service at (773) 869-1234 before sending any equipment back for
repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET
FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for
the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or
warranty as to the suitability or fitness of these devices for any specific application.
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered
into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense. The user must use shielded cables and connectors with this product. Any
changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique
series number. The series number can be found on the product nameplate label, along with all required approval markings
and information. When requesting compliance information for this product, always refer to the series number. The series
number should not be confused with the marking name or model number of the product.
The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
Made in China
1111 W. 35th Street • Chicago, IL 60609 USA
9
.200904140 93-2899 Rev. A - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
|