_______________________________________________________________
TRIAX TSR 1000
________________________________________________________________
Digital Satellite Receiver FTA
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating: Slots and openings in the cabinet are provided for ventilation to
protect it from overheating. Do not block these openings or allow them to be
blocked by placing the STB on a bed, sofa or other similar surface, nor should it
be placed over a radiator or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it
will not be walked on. Please take special attentions to cords at plugs,
convenience rece ptacles and the point where they exit from the unit.
Object and Liquid Entry: Never put objects of any kind into this STB through
openings, as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill any liquid on the STB.
Note: Moisture may be formed inside the unit in the following conditions:
¾ When the unit is suddenly moved from a cold environment or an
air-condition room to a warm place.
¾ Immediately after a heater has been turned on.
¾ In a steamy or very humid room.
If the moisture forms inside the unit, it may not operate properly. To correct this
problem, turn on the power and wait about two hours for the moisture to
evaporate.
Parts Replacement: When the unit parts need to be replaced, user should
make sure the service technician use the replacement parts specified by the
manufacturer or having the same characteristics as the original part.
Unauthorized replacement may put the unit in the risk of fire, electric shock or
other hazards.
Safety Check: After all the maintenances and repairs are done, user is
required to request the service technician to conduct the overall safety check
to ensure the mach-
ine is in the proper condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
CONTENTS
1. Remote Control & Panel Description .......................................................3
1.1 Front Panel Description...........................................................................3
1.2 Rear Panel Description ...........................................................................4
1.3 Remote Control Description ....................................................................5
2. Basic Operations........................................................................................6
2.1 Switch on STB.........................................................................................6
2.2 Standby Mode: ........................................................................................6
2.3 Channel +/-..............................................................................................6
2.4 Volume +/-...............................................................................................6
2.5 Channel Number .....................................................................................7
2.6 Mute.........................................................................................................7
2.7 Pause ......................................................................................................7
2.8 Recall.......................................................................................................7
2.9 Favorite....................................................................................................7
2.10 EDIT ......................................................................................................8
2.11 Audio Track / Mode ...............................................................................8
2.12 INFO......................................................................................................8
2.13 EPG.......................................................................................................8
2.14 TV/RADIO..............................................................................................9
2.15 Channel List...........................................................................................9
2.16 Change Satellite..................................................................................10
2.17 MULTI-PIC...........................................................................................10
2.18 LNB Short............................................................................................10
2.19 SUB .....................................................................................................11
2.20 TXT......................................................................................................11
2.21 OK .......................................................................................................11
3. Channel .....................................................................................................12
3.1 TV Channel List.....................................................................................12
3.1.1 Favorite ...........................................................................................13
3.1.2 Move................................................................................................13
3.1.3 Sort..................................................................................................13
3.1.4 TV Channel List Edit .......................................................................14
3.1.4.1 Delete........................................................................................14
3.1.4.2 Skip...........................................................................................14
3.1.4.3 Lock ..........................................................................................14
3.1.4.4 Edit............................................................................................14
3.1.5 Find .................................................................................................15
3.2 Radio Channel List................................................................................16
3.3 Channel Setup.......................................................................................16
3.4 Favorite channel list name ....................................................................17
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3.5 Delete All ...............................................................................................17
3.6 Restore channel list and settings.............................................................17
3.7 Save channel list and settings.................................................................18
4. Installation ................................................................................................19
4.1 Antenna Setup.......................................................................................19
4.2 Single Search........................................................................................20
4.3 Multi Search...........................................................................................21
4.4 TP Scan.................................................................................................21
4.5 Satellite List ...........................................................................................22
4.6 TP List ...................................................................................................23
4.7 Satellite Guide.......................................................................................24
5. System Setup............................................................................................26
5.1 Language...............................................................................................26
5.2 TV System.............................................................................................27
5.3 Time & Timer Setting.............................................................................27
5.4 OSD Setting...........................................................................................29
5.5 Parental Lock.........................................................................................30
5.6 LNB Power ............................................................................................30
5.7 RCU position switch ..............................................................................31
6. Tools..........................................................................................................32
6.1 Information.............................................................................................32
6.2 Quick Setup...........................................................................................32
6.3 Game.....................................................................................................32
6.4 Factory Default......................................................................................34
6.5 Software Upgrade .................................................................................34
6.6 SatcoDX Auto Programming .................................................................37
7. Technical Specification ...........................................................................38
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control & Panel Description
1. Remote Control & Panel Description
1.1 Front Panel Description
1. POWER: Is used to switch between the working mode and the standby
mode.
2. Display (4-Digit/7-Segment): Displays the received channel number while
operating and time while in standby mode.
3. Remote Sensor: Detects the infrared signals from the remote control unit.
4. VOL+/-: To change volume to move cursor, change numbers in the menu
or to change the choice.
5. MENU: To enter into the main menu and exit all menus.
6. CH+/-: To change channels or for navigating and changing values in
menus.
7. OK: To select an item in the menu and confirm it or pop up channel list
when no menu.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control & Panel Description
1.2 Rear Panel Description
1. IF OUT:
Satellite output for cascading to other devices
Note: The operation of another receiver at the same time is only possible
with limited channel selection.
2. IF IN:
Satellite input.
3. RS-232:
4. ANT IN:
5. AC IN:
Serial Port allowing software upgrades.
Connect the antenna of TV to Aerial IN.
Mains input cable.
6. POWER ON/OFF:
7. VIDEO / AUDIO:
8. TV SCART:
9. TO TV:
Allows to completely switch off the receiver.
HiFi outputs for stereo set or monitor.
Output SCART for the connection to a TV set.
Output to TV.
10. VCR SCART:
Output SCART for the connection to a VCR set.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control & Panel Description
1.3 Remote Control Description
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
2. Basic Operations
2.1 Switch on STB
Switch the [Device’s Main Power] switch on.
you will set Language, First Audio, Second Audio, LNB Power, Antenna Setup
and Multi Search.
? Frequently Asked Question
Q: The power of my STB is on and it is running in TV mode but the TV
screen shows nothing:
A: Make sure the TV set has been set to the correct video input(not the
TV channels). For example, if you have connected the unit to the
video1 input of the TV set then you need to select the corresponding
input of the TV. Mostly it is done with the AV button of the TVs remote
control unit.
Q: My STB is running in TV mode but the TV screen shows nothing
except one ball and “No Signal”.
A: That means the channel you selected has no signal. This can be
caused by several reasons:
1. The channel you selected is not from the satellite to which your dish is
pointing. Select another channel.
2. The signal of current TV channel is too weak. You can try to change to
other channels with a stronger signal. If the problems still exist, please
consult your local dealer or installer for technical service.
3. You selected the wrong LNB type in the installation menu or your DiSEqC
switch configuration is not correct.
2.2 Standby Mode:
1. Press [Power] button to switch from TV/radio mode to standby mode
2. In standby mode press [Power] button again to switch back to TV/radio
mode. The last active channel will be showed.
3. To switch off the STB complete press the main power button.
2.3 Channel +/-
In TV/radio mode press [Channel Up/Channel Down] to change channel.
2.4 Volume +/-
In TV/radio mode, press [Volume Up/Volume Down] to adjust volume.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
2.5 Channel Number
In TV/radio mode you can enter the channel number directly with your remote
control unit and confirm the number with the OK button to change to the desired
channel.
2.6 Mute
1. Press the [Mute] button to mute the sound. On the screen an icon will be
displayed to indicate the muted sound.
2. Press the [Mute] button again to restore the sound.
2.7 Pause
1. In TV/radio mode, press the [Pause] button to stop the display. The sound
of the channel will continue.
2. Press [Pause] again to continue the display at the actual moment.
2.8 Recall
Pressing the [Recall] button allows you to toggle between the actual and the last
selected channel.
2.9 Favorite
1. In full screen, press the [Favorite]
button to display the “Favorite Group”
window on the screen as the picture
beside shows.
2. In the “Favorite Group” window you
can select the desired favorite channel
with [Channel Up / Down] and confirm
it with [OK] to switch to it. In bigger
groups you can navigate with [Page
Up / Page Down].
3. With [Volume Up / Down] you can select different favorite groups.
4. Press [Exit] to close the “Favorite Group” window.
? Frequently Asked Question
Q: Why the screen displays “No Favorite Channel” after pressing the
[Favorite] button?
A: No channels have been assigned to a favorite group yet. You can do this in
the channel menu.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
2.10 EDIT
In TV mode, press the [EDIT] button to open the “TV Channel List” window.
2.11 Audio Track / Mode
1. In TV mode, press the [Audio] button
to open the audio mode window.
2. Select the item you want to adjust with
[Channel Up/Down] and change the
value with [Volume Up/Down].
2.12 INFO
In TV mode, press [INFO] button can open
information screen, in the window shows
the parameters of current channel.
Two dynamic bars at the bottom of the
window reflect the signal intensity and
signal quality of the current channel.
2.13 EPG
1. The STB supports Electronic Program
Guides (EPG) to give you information
about the actual programs of certain
channels like event name, subtitle,
description, start and finish time. This
feature is depending on the service of
the channel provider.
Press [EPG] to open the EPG window.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
2. The [Red] button opens the detailed
schedule of the marked channel. You
can select an event with [Channel
Up/Down] and display the event’s
detailed description with [OK].
3. Press the [Green] button in the EPG
menu to display the detailed
information of the actual event in the
selected channel. With the [Yellow]
button you can program a timer with
the start and finish time and date of
this event.
4. Press the [Yellow] button in the EPG
menu to program a timer with the
actual events data.
5. To close the EPG menu press [Exit].
2.14 TV/RADIO
In TV mode, press [TV/RADIO] to switch to radio mode. In radio mode press
[TV/RADIO] again to switch back to TV mode.
2.15 Channel List
1. In TV/radio mode press [OK] button to open the channel list window.
2. Press [Green] button to sort the channels by free and scrambled channels.
Free channel are listed first and scrambled channels last.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
3. Press [Yellow] button to open the SAT
list. After selecting a satellite the
channel list will be reduced to the
channels of this satellite.
4. Press [FAV] button to open FAV list.
After selecting a favorite group the
channel list will be reduced to the
channels of this group.
5. Press [Blue] button to open the find
window. You can use this feature to
find channel by their names.
6. Press [OK] to change and display the marked channel.
2.16 Change Satellite
1. In TV/radio mode, press [Page Up/Down] to switch directly between
satellites.
2. In TV/radio mode, press [SAT] to open satellite list and select there.
2.17 MULTI-PIC
In TV mode, press [MULTI-PIC] button to
enter the “PIC Select” menu.
1. In “PIC Select” menu, it has 4 options,
you can choose 4 PIC, 9 PIC, 16 PIC
or 12 PIC channels’ preview window
(static), starting from the current
channel. Only the marked preview
program is continuously playing.
2. Press [CH▲/▼/ VOL◄/►] to change
the marked channel among the
preview programs.
3. With the number buttons [1] ~ [9] you can directly move the highlight to the
related channel.
4. With [OK] you return to full screen mode in the marked channel.
2.18 LNB Short
When LNB is short, it will notify user on screen “LNB Short!” Please check your
cables and connections for shorts. When the short is removed the warning
message will disappear.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
2.19 SUB
SUB(Subtitle): In “OSD Setting”menu, use [Volume Up/Down] to select “On” or
“Off”. If the current channel has subtitle information, it will be displayed if this
function is “On”. If this function is “Off” subtitles won’t be displayed.
2.20 TXT
1. Press [TXT] button in TV mode to open the teletext page. This service is
depending on the support of the channel provider.
2. If the channel does not support teletext information, it will show “No
Teletext Data” on the screen.
2.21 OK
In full screen, press [OK] button to open all satellite channel list. Press [Red] on
the RCU to switch between 1 column and 3 column.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3. Channel
Press [Menu] in the TV/radio mode to enter
the main menu.
1. Press [Channel Up/Down] to select
the channel item.
2. Press [OK] to enter the selected item.
In the channel menu:
Press [Channel Up/Down] to select the
wanted menu item among TV Channel List,
Radio Channel List, Channel setup,
Favorite channel list name, Delete All,
Restore channel list and settings and Save
channel list and settings.
Press [OK] to enter the selected item.
3.1 TV Channel List
If you enter the channel list menu a window
like the one below will open.
1. You can move the highlighted channel
with [Channel Up/Down] and press
[OK] to preview the highlighted
program in the preview window.
2. Press [Page Up/Down] on the RCU to
jump between the channels by pages.
3. Press [Volume Up/Down] to switch
satellite of the program group.
4. Press [MENU] button to enter TV playing mode.
5. The color buttons offer further functions to manage the channel list.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3.1.1 Favorite
1. Press [FAV] to open the favorite
window.
2. You can select between 8 favorite
groups with [Channel Up/Down].
Press [OK] to assign the channel to a
favorite group, press [EXIT] to exit
favorite group.
3. Press [OK] again to remove the
channel from the marked favorite
group.
4. Press [MENU] button you will be asked “Are you sure to save?”. Select
“Yes” to save the marked favorite group. Select “No” to cancel the
operation.
5. To return to the TV channel list. The channels of favorite groups are
indicated with a favorite icon behind the name.
3.1.2 Move
1. press [Red] button to show a moving
icon behind the channel name.
2. Move the channel to the desired
position with [Channel Up/Down].
Press [OK] to confirm the position.
3.1.3 Sort
1. Press
[Green] to open the sort
window. Press [Channel Up/Down] to
select and [OK] to confirm your
choice.
2. The ways of sorting are:
¾
Name(A-Z):
Sorting
in
Alphabetical order, ignoring “$”
symbol.
¾
Name(Z-A):
Sorting
in
Alphabetical order, ignoring “$”
symbol.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
¾
¾
FTA: Sort channel by free and scrambled sequence. Free channels
will be listed first and scrambled channels behind in the channel list.
Lock: Unlocked channels are listed first end locked channels at the
end.
3.1.4 TV Channel List Edit
After pressing the [Yellow] button a window
for entering the password will open. The
default password is “0000”.
You can Move, Skip, Lock and Rename the
channel.
Press [MENU] to leave the channel editing.
The system will ask you to confirm the
saving of the changes you made.
3.1.4.1 Delete
In edit channel menu, Press [Red] button to show a delete icon behind the
channel name. Press [MENU] button you will be asked “Are you sure to save?”
Select “Yes” to delete the marked channel. Select “No” to cancel the operation.
3.1.4.2 Skip
In channel edit menu, press [Green] button to place a skip icon behind the
name of the highlighted channel. Marked channels will be skipped when you
change channels in TV mode after you confirm to save the changes when you
leave this menu.
3.1.4.3 Lock
In channel edit menu, press [Yellow] button to place a lock icon behind the
name of the highlighted channel. Marked channels will be locked and displayed
only after password has been entered if you confirm to save the changes when
you leave this menu.
3.1.4.4 Edit
Pressing the [Blue] button in the TV
Channel List Edit menu will open another
window where you can choose between
Edit the actual channel or create a new
channel. To edit the channel press the
[Red] button.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
1. Selecting the name item with [OK] will
display a button pad to show you how
to edit the channel name.
2. On the “Video PID”, “Audio PID” and
“PCR PID” items you can input
numbers to modify the item’s value.
3. After modification select “Save” and
press [OK] button to save the modified
values and exit “Edit” mode. Or select
“Exit” and press [OK] to leave Edit
mode without saving the modifications.
Create
Press [Green] button to open the Create
window.
1. Press [OK] button on the “Satellite”
item to display the satellite list. You
can select the satellite for which you
want to create a new channel.
2. With marked “TP Index” item press
[VOL◄/►] to select the TP number
where the channel can be found. The
next three items will show the related
parameters.
3. Highlight the “Name” item and press [OK] to display the button pad and
edit the new channel’s name.
3.1.5 Find
1. Press [Blue] button to open the “Find”
window like showed below. Press
[Channel/Volume Up/Down] to select
the leading character of the channel
name and press [OK] to confirm it.
2. After entering the character(s)
highlight in the window and press [OK]
on the RCU.
3. Press [MENU] button to close the find
window and brings you back to the
channel list.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3.2 Radio Channel List
Basically the operation of “Radio Channel List” is same as “TV Channel List”,
except that in the small channel window the radio Logo will be displayed.
3.3 Channel Setup
When you enter the “Channel Setup” menu
you will see a screen like beside:
1. Startup Channel: Press [OK] to enter
“Startup Channel” menu to see the
screen like showed beside:
¾
If you set of “Boot on Channel” to
“On” you can edit the following
two items. If the setting is “Off”
the box always starts with the
channel that was running when
the box has been switched off.
¾
¾
On the “Mode” item you can select either “TV channel” or “Radio
channel”.
On “Startup Channel” item you can open the channel list by pressing
[OK]. Then you can select the channel of you choice. Press [OK]
again to confirm.
2. Channel Play type: Use [Channel
Up/Down] to select, press [OK] to
enter “Channel Play Type” menu.
Here you can select the “playing
channels” as “All”, “Free” or
“Scrambled”.
3. If you select “Free” then all scrambled
channels will be skipped when you
change channels with [Volume
Up/Down].
Press [Exit] to leave the “Channel Setup” menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3.4 Favorite channel list name
When you enter “Favorite channel list
name” menu with 8 favorite group will be
displayed. Press [Red] or [OK] key on the
RCU to rename favorite group with the
[Number] buttons. After modification select
“Save” and press [OK] to save the favorite
group name and leave the edit mode.
Select “Exit” and press [OK] to exit the edit
mode without saving the favorite group
name.
3.5 Delete All
To delete all channels:
1. Enter the password. The default
password is “0000”.
2. After entering the password correct a
safety question will show up where
you have to confirm first
3. Select “Yes” to delete all channels or
“No” to cancel and confirm with [OK].
4. In step 1 and step 2, pressing [Exit]
will exit the function directly without
saving.
? Frequently Asked Question
Q: IF I incautiously delete all channels, what should I do?
A: there are two ways to restore:
¾
¾
To re-search all channels in the “Installation” menu.
Use “Default Value” function to restore all channels in the “Tools” menu.
3.6 Restore channel list and settings
To restore channel list and settings.
1. Enter the password. The default
password is “0000”.
2. After entering the password correct a
safety question will show up where
you have to confirm first.
3. Select “Yes”, press [OK] to restore the
last backup channel list, the current
channel list will be erased. Select “No”
press [OK] to cancel the operation.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3.7 Save channel list and settings
To save channel list and settings.
1. Enter the password. The default
password is “0000”.
2. After entering the password correct a
safety question will show up where
you have to confirm first.
3. 3. Select “Yes”, press [OK] to save
current channel list to backup channel
list. Select “No” press [OK] to cancel
the operation.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
4. Installation
After selecting the installation menu you
can see the window like beside.
In “Installation” menu;
1. Press [Channel Up/Down] to select
menu items among Antenna Setup,
Single Search, Multi Search, TP Scan,
Satellite List, TP List and Satellite
Guide.
2. Press [OK] to enter the selected item.
4.1 Antenna Setup
After selecting antenna setup another
window will be opened.
You can edit the following items:
1. Satellite: Press [Volume Up/Down] to
switch satellites or press [OK] to enter
satellite list to select directly.
2. LNB Configuration: Press [OK] to
enter LNB configuration, you will see a
window like beside:
LNB Type: Press [Volume Up/Down]
to switch among “Standard”, “User” and “Universal” mode.
For Example: If you use a Dual LNB,
then you should select “User” option
in “LNB Type” and set the correct
frequency in LNB type.
22K: Use [Volume Up/Down] to
switch “ON” and “Off”. The 22KHz
signal is used in KU universal LNBs to
change between low band and high
band.
! Notice: After choosing LNB type
“Universal” you cannot modify 22K.
DiSEqC1.0: Use [Volume Up/Down] to switch the options of DiSEqC1.0
switches between Disable / LNB1 / LNB2 / LNB3 / LNB4.
DiSEqC1.1: Use [Volume Up/Down] to switch DiSEqC1.1 option or press
[OK] to enter DiSEqC1.1 option to select directly. The options of this item
are: Disable / 1Cascade M1 Port1 / 1Cascade M1 Port2 / 1Cascade M1
Port3 / 1Cascade M1 Port4 / 1Cascade M2 Port1 / 1Cascade M2 Port2 /
1Cascade M2 Port3 / 1Cascade M2 Port4 / 1Cascade M3 Port1 /
1Cascade M3 Port2 / 1Cascade M3 Port3 / 1Cascade M3 Port4 /
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
2Cascades Port1 / 2Cascades Port2 / 2Cascades Port3 / 2Cascades
Port4 / 2Cascades Port5 / 2Cascades Port6 / 2Cascades Port7 /
2Cascades Port8 / 2Cascades Port9 / 2Cascades Port10 / 2Cascades
Port11 / 2Cascades Port12 / 2Cascades Port13 / 2Cascades Port14 /
2Cascades Port15 / 2Cascades Port16.
Positioner: Press [Volume Up/Down] to select between “None /
DiSEqC1.2 / USALS”.
Toneburst: Press [Volume Up/Down] to switch this function “On” or “Off”.
Polarity: Press [Volume Up/Down] to switch between “Auto / H / V/ Off”.
0/12V: Use [Volume Up/Down] to switch “ON” and “Off”.
3. DiSEqC1.0: Use [Volume Up/Down] to switch the options of DiSEqC1.0
switches. Between Disable / LNB1 / LNB2 / LNB3 / LNB4.
4. TP Index: Use [Volume Up/Down] to select the desired transponder.
5. FTA Only: Press [Volume Up/Down] to select to scan only free channels or
even scrambled channels. If you select “Yes” it will scan free channels only.
6. Scan Channel: Press [Volume Up/Down] to select to scan TV + radio
channels, or just TV channels or just radio channels.
7. Scan Mode: You can select “Preset Scan” or “Network Scan” to scan
preset transponders or network transponders of the selected satellite.
8. Search: Press [OK] to start scanning. In the lower part of the window the
progress of scanning and the found channels are displayed.
4.2 Single Search
After selecting “Single Search” you will see
a window like beside:
1. In the “Satellite” item press [Volume
Up/Down] to select the satellite which
you want to scan or press [OK] to
open the “satellite list” to select
directly.
2
In the “FTA Only” item, press [Volume
Up/Down] to select to scan only free
channels or even scrambled channels.
If you select “Yes” it will scan free channels only.
3
4
5
In “Scan Channel” item, press [Volume Up/Down] to select to scan TV +
radio channels, or just TV channels or just radio channels.
In “Scan Mode” item you can select “Preset Scan” or “Network Scan” to
scan preset transponders or network transponders of the selected satellite.
Move the highlight to “Search” and press [OK] button to start scanning.
Bars are showing the progress of the channel scanning in the lower part of
the window and the found channels are listed.
6
You can stop the scan with [MENU] button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
4.3 Multi Search
When you enter the “Multi Search” menu a
window like the one beside will open.
1. On “Satellite” item press [OK] to open
the satellite list. Then press [Channel
Up/Down] to move the highlight and
press [OK] to mark/unmark and
[MENU] to finish the selection. You can
select several satellites in this menu.
The system will use DiSEqC1.0/1.1,
DiSEqC1.2 and USALS functions to
search the marked satellites and scan channels.
2. On “FTA Only” item, press [Volume Up/Down] to select scanning of all
channels or just scanning of free channels. If you select “Yes” it will scan
free channels only.
3. On “Scan Channel” item, press [Volume Up/Down] to select the scanning
range from TV + radio channels, only TV channels or only radio channels.
4. On “Scan Mode” item, you can select “Preset Scan” or “Network Scan” to
scan preset transponders or network transponders of the selected satellite.
5. Select “Search” and press [OK] to start scanning. In the lower part of the
window the progress of scanning and the found channels are displayed.
6. Press [MENU] to cancel the scanning.
4.4 TP Scan
When you enter “TP Scan” menu a window
like the one beside will be displayed.
1. On “Satellite” item, press [Volume
Up/Down] to select the satellite you
want to scan or press [OK] to open the
satellite list for selection.
2. On “TP Index” item use [Volume
Up/Down] to select the desired
transponder or [Red] and [Green] key
on the RCU for the related functions.
¾
When you press [Red] it will display “New Carrier” in “TP Index” item.
You have to set the parameters of “TP Frequency” and “Symbol Rate”
for this new transponder. Therefore use the number buttons of the
RCU. The available range are “3000~13450MHz” and
“1000~45000KS/s”.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
¾
When you press [Green] a safety question will be displayed for
confirmation to delete the current transponder or not. If you select
“Yes”, the current transponder will be deleted and the total number of
transponders will be reduced.
3. For existing transponders you also can use number buttons to modify the
parameters of “TP Frequency” and “Symbol Rate” or [Volume Up/Down] to
change the value directly. “Polarity” and “FTA only” are used for setting
scans conditions. Press [Volume Up/Down] to select a different mode.
4. On “TP Index” item, press [Red] button to add a new TP.
5. Press [Green] button to delete the current TP.
6. Press [Yellow] button to delete all transponders on current satellite.
7. After you completed your modification select the “Search” item and press
[OK] to start scanning.
8. On the “TP Scan” item, press [MENU] to cancel the scanning and saving
the found channels.
4.5 Satellite List
When you enter the “Satellite List” menu
you can see a window like the one beside:
1. Press [Red] button to enter edit
satellite menu. You can edit the
satellite’s name and its longitude.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
2. Press [Green] button to open the “Add
satellite” window.
3. After pressing [Yellow] button you will
be asked “Are you sure to delete?”.
Select “Yes” to delete the marked
satellite. Select “No” to cancel the
operation.
4.6 TP List
When you open the “TP List” menu you will
see a window like the one beside.
1. Press [Volume Up/Down] to change
the marked satellite.
2. Press [Red] button to open the “Edit
TP” menu. Here you can edit the
transponder’s data.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
3. Press [Green] button to open the “Add
TP” menu. Here you can add a new
TP and setup its parameters.
4. Press [Yellow] button will open a
dialog box asking you to confirm the
deletion of the current TP. If you select
“Yes” all the related channels will be
deleted. If you select “No” the
operation will be cancelled.
5. Pressing the [Blue] button will open a
dialog box asking you to confirm the
deletion of all TP on current satellite. If
you select “Yes”, all TP of the current
satellite will be deleted. If you select
“No” the operation will be cancelled.
4.7 Satellite Guide
When you enter “Satellite Guide” menu,
you will see the screen like beside:
Here you can enter your local longitude
and latitude and the satellite’s longitude.
The receiver calculates the antenna’s
azimuth and elevation to point your
antenna to the selected satellite.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
1. Use the [Number] buttons to input the values of “Local Longitude”, “Local
Latitude” and “Satellite Longitude”.
2. Press [Volume Up/Down] to switch east or west in “Local Longitude” and
“Satellite Longitude” or to switch north or south in “Local Latitude”.
3. Highlight the “Start” item and press [OK]. In the lower part of the window
the corresponding values for the antenna setting is displayed.
4. Orientation means the angle between south and satellite.
5. Press [MENU] to leave this feature.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
5. System Setup
When you open the “System Setup” menu
a window like the one beside will be
opened.
In “System Setup” menu:
1. Press [Channel Up/Down] to select
menu items among Language, TV
System, Time & Timer setting, OSD
Setting, Parental Lock, LNB Power
and RCU position switch.
2. Press [OK] to open the selected item.
5.1 Language
After selecting the “Language” menu you
will see a window like beside:
1. Language: Press [Volume Up/Down]
to select languages. The selection of
languages include: English, German,
French, Italian, Portuguese, Spanish,
Turkish, Polish, Hungary, Russian,
Arabic, Farsi, Danmark and Greece.
2. First Audio: Some channels offer more
than one audio language. This
function allows you to set the preferred audio language for those channels.
If a channel offers the same audio language as the “First Audio” you set
the system will play this audio language as default. If the channel does not
offer this audio language then the system will compare the offered
languages with the second audio language. The selections of audio
languages include: English, French, German, Russian, Arabic, Portuguese,
Turkish, Spanish, Polish and Italian.
3. Second Audio: If the channel has no audio language that corresponds with
“First Audio” but with “Second Audio” the system will play the second audio
language as default. If no audio language corresponds with the “Second
Audio” then the default language of the current channel will be played
instead. The selections of audio languages include: English, French,
German, Russian, Arabic, Portuguese, Turkish, Spanish, Polish and
Italian.
4. Press [MENU] to return back from “Language” menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
5.2 TV System
When you enter the “TV System” menu
you will see the screen like below:
1. Display Mode is used to switch the
display mode. You can select from
Auto / PAL / PAL-N / PAL-M /
NTSC3.58. Press [Volume Up/Down]
to switch the desired mode.
2. Aspect Mode is used to switch the
screen aspect ratio mode. You can
select from Auto / 4:3 PS / 4:3 LB /
16:9. Press [Volume Up/Down] to select the needed mode.
3. Video output is use for switching the screen aspect ratio mode. Now we
provide below options: RGB / CVBS. You can press [Volume Up/ Volume
Down] key to select each mode circularly.
4. VCR Loopthrough is use for switching STB master and VCR master. When
VCR Loopthrough is STB master mode, video output is available.
5. Select RF system between PAL B/G, PAL I, PAL D/K and NTSC M.
6. RF Channel: In case your TV is connected through RF modulator (UHF),
select output channel number you want.
7. Press [MENU] to close the “TV System” menu.
5.3 Time & Timer Setting
When you enter “Time & Timer Setting” a
menu with this 3 items will be opened.
1. Time: When you select “Time” and
press [OK] then you will see a window
like the one beside:
¾
GMT Usage: This item is used to
set the time by using the time
signal from the satellite. Press
[Volume Up/Down] to change the
setting.
¾
¾
The “GMT Offset” item is only available when “GMT Usage” is set to
“On”. Press [Volume Up/Down] to set the “GMT Offset” value. With
every time you press the button the time offset will be
increased/decreased by half an hour.
“Date” and “Time” items are only available when the “GMT Usage” is
set to “Off”. Press [Volume Up/Down] to select one item and use
number buttons to input time and date directly.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
¾
NOTE: If the current channel
provides the correct time
information, you will see the
current time after you entered
“Time” menu. If the channel
doesn’t provide time information,
you have to input the date and
time information manually. The
most channels support the time
signal.
¾
Press [MENU] to leave the “Time” menu.
2. Timer: Select “Timer” item and press [OK] to enter the “Timer list” menu.
You can press [Channel Up/Down] to select a timer. Then press [OK] to
open the related timer menu.
¾
¾
¾
The current time will be displayed
in the first column. If the current
time is incorrect, please modify it
with the [Number] buttons.
Timer Number: You can press
[Volume Up/Down] to switch the
Timer number. There are totally 8
timers.
Timer Mode: Select how often the
timer is running: Once, Daily, Weekly, Monthly and Yearly, or switch
the timer: Off.
¾
¾
Timer Service: Select between Channel(timer setting for channel
change and Wakeup/Sleep) and Message(reminding message).
When you select “Channel”(timer setting for channel change and
Wakeup/Sleep) then you have further options you need to set:
♦
Wakeup Channel: Press [OK] to enter the channel list and select
the channel you want to see.
♦
♦
Wakeup Date: Use number buttons to input your wakeup date.
On Time: Use number buttons to input your wakeup time. If date
and time are reached then no matter if the system is in standby
mode or in playing mode, it will automatically switch to the
channel you set and start to play.
♦
Duration: Here you can set the time you want to see or play this
channel. After the time set the system will automatically switch to
standby mode. If you don’t want the box the be switched to
standby mode then set the duration to 00:00.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
¾
When you select “Message”(reminding message) option in “Timer
Service” then you can enter additional data:
♦
Wakeup Message: Press [Volume Up/Down] to select the
category of the reminding message from Birthday, Anniversary
and General.
♦
♦
Wakeup Date: Use the [Number] buttons to input your wakeup
date.
On Time: Use the [Number] buttons to input your wakeup time. If
date and time are reached, no matter if the system is in standby
mode or in playing mode, it will automatically show a reminding
message.
♦
The message will be displayed on the screen until you press [Exit]
to close it.
Press [MENU] to leave the “Timer” menu.
3. Sleep Timer: Select “Sleep Timer” item and press [OK] to set the sleep
timer. You will see “Sleep timer OFF / Sleep timer 10 / Sleep timer 30 /
Sleep timer 60 / Sleep timer 90 / Sleep timer 120”.
If you set a sleep time, the system will change to standby mode after the
chosen time period.
5.4 OSD Setting
When you select “OSD Setting” you will
see a screen like beside:
1. Subtitle Display: Press [Volume
Up/Down] to select “On” or “Off”. If the
current
channel
has
subtitle
information, it will be displayed if this
function is “On”. If this function is “Off”
subtitles won’t be displayed.
2. OSD Timeout: This setting determines
the duration the info window is
displayed on the screen when you change channels. Press [Volume
Up/Down] to set the time between 1 to 10 seconds.
3. OSD Transparency: With this parameter you can set the transparency of
the menus. Press [Volume Up/Down] select the value between 10%, 20%,
30%, 40% and “Off”(means no transparency function).
4. Load OSD Setting Default: If you want to reset your OSD settings to the
default settings then select this item and press [OK].
5. Press [MENU] button to leave the “OSD Setting” menu.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
5.5 Parental Lock
You can set a password for anyone who
wishes to operate the “Installation” menu.
You can also set the password to lock
channels. Below you find how to set and
change the password.
1. On “Parental Lock” press [OK] to open
a
dialogue box and input the
password. After you entered the
correct password, you will see a
screen like beside:
2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the
password every time you want to open the menu. If set to “No” then you
can open the menu without entering the password first.
3. Channel Lock: If set to “Yes” then you need to enter the password before
you can see those channels which have been marked as locked channels
in the Channel menu. If set to “No” then even those channels can be
selected without entering the password first.
4. New Password: Here you can change the existing password. You should
do this after you set up the receiver the first time and every time when you
think that your password is known by unauthorized persons. To change the
password enter the new password in the “New Password” item and repeat
the same one in the “Confirm Password” item. If the passwords are not
identically then you will see a warning message. If you entered the same
new password in both fields then you will see the message “Saving Data,
Please Wait…”. From now on you need to use the new password to open
locked menus or locked channels.
NOTE: The default password is 0000
5. Press [MENU] to leave the “Parental Lock” menu.
5.6 LNB Power
Here you can set the power output to the LNB. If your receiver is connected to
the LNB directly then you need to set the LNB power to “On”. If your receiver is
connected to a multi switch(SMATV signal distribution system) then it may be
that you don’t need to provide the power to the LNB. But since this is depending
on the kind of installed distribution system we recommend you to contact your
installer or to refer to the user manual of this system to get the correct
information.
You also just can change this setting and check if you still can receive the
channels. If the LNB power is off and you still can see all channels then we
recommend this setting in order to save energy.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
5.7 RCU position switch
1. This item can select the switch controller’s position. The position number
you choose in this menu must be same as the switch controller’s setup, or
the switch controller can not work correctly.
2. Press [◄/►] to modify the change.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
6. Tools
When you enter to “Tools” menu, you will
see a screen like beside:
In “Tools” menu:
1. Press [Channel Up/Down] to select
the wanted item among Information,
Quick Setup, Game, Factory Default,
Software Upgrade and SatcoDX Auto
Programming.
2. Press [OK] button to enter the
selected item.
6.1 Information
1. When you select the “Information”
menu you will see a screen like beside.
The screen displays data about the
current channel.
2. Press [MENU] button to leave the
information display.
6.2 Quick Setup
When the STB is used, which need to
repeat set Language, First Audio, Second
Audio, LNB Power, Antenna Setup and
Multi Search. Particular explain consult 4.1,
4.3 and 5.1.
6.3 Game
When you enter “Game” menu, you will
see three games include Tetris, Snake and
Othello.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
Basic operation statement:
1. Tetris
¾
Mark “Setup” and press [Volume
Up/Down] to select the level
(speed).
¾
¾
¾
Mark “Start” and press [OK] to
start the game.
Mark “Cancel” and press [OK] to
leave the game.
Play the game:
♦
Press [Volume Up/Down] to
move the block left or right
♦
♦
♦
♦
Press [Channel Up] to rotate the block clockwise
Press [Channel Down] to drop the block faster
Press [OK] to Pause/Play the game
Press [MENU] to leave the game and return to the game menu.
2. Snake
¾
Mark “Setup” and press [Volume
Up/Down]
to
select
the
level(speed).
¾
¾
¾
Mark “Start” and press [OK] to
start the game.
Mark “Cancel” and press [OK] to
leave the game.
Play the game:
♦
Press [Volume Up/Down /
Channel Up/Down] to guide
the snake to the red blocks. Every block you ate increases the
length of the snake. If the snake runs against a wall or against
itself then it dies.
♦
♦
Press [OK] to Pause/Play the game
Press [MENU] to quit the game and return to the game menu.
3. Othello
¾
Mark “Setup” and press [Volume
Up/Down] to select the game
level(degree of difficulty).
Mark “Start” and press [OK] to
start the game.
Mark “Cancel” and press [OK] to
leave the game.
Play the game:
¾
¾
¾
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
♦
Press [Volume Up/Down / Channel Up/Down] to position the
round mark.
♦
♦
Press [OK] to set your stone.
Press [MENU] to quit the game and return to the game menu.
6.4 Factory Default
When you press [OK] on the “Factory
Default” item:
1. A dialogue box will occur where you
need to enter the password.
2. After you input the correct password a
warning message will be displayed
like the one beside.
3. If you select “Yes” then all changes
you made will be reset to default
values. Make sure you really want to
do this!
4. Press [MENU] in both steps will close the window without resetting the
receiver.
6.5 Software Upgrade
1. This function allows you to upgrade
the software of the receiver. This can
be done from PC to receiver or from a
master receiver to a slave receiver.
2. Connect master receiver or PC to the
slave
receiver
via
serial
interface(0-Modem cable). Enter the
“Software Upgrade” menu of the
master receiver and press [Volume
Up/Down] to change the upgrade
mode. Upgrade modes include: allcode / maincode / CAS-data /ScriptGUI /
Radioback / default db / userdb.
3. Switch on the slave receiver.
4. Mark “Start” on the master reeciver and press [OK] to start upgrade.
Wait until the display on the front panel shows “END”. Then switch off the
receiver and on again. Now the new software is used.
5. Press [MENU] to save the setting without upgrade.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
Update Software(receiver to receiver)
1. Connect master and slave receivers with twisted RS-232C cable.
2. Power on the master receiver and make it in standby mode input number
key.
3. Turn on slave receiver to begin update.
4. Input the password “123” by remote control to update the software.
5. After update, it will display “-End” on slave panel.
6. Turn off slave receiver, disconnect twisted RS-232C cable and restart it.
Notes: Input the password “123” to update the software.
Input the password “456” to update the data.
Input the password “789” to update the software and data.
Input the password “369” to copy the whole flash.
Update Software(Computer to receiver)
1. Connect your PC and receiver with twisted RS-232C cable.
2. Turn on the receiver.
3. Startup the software of “upgrade_Ali.exe” on your PC, press “Select” key
and select “*.bin”, then select port. Press “start” on your PC. Upgrade will
begin.
4. After upgrade, the receiver will display “-End” on panel.
5. Turn off the receiver, disconnect twisted RS-232C Cable and restart it.
Notes:
You need a 9-pin twisted RS-232C cable(pin-2 to pin-3, pin-3 to pin-2, pin-5
to pin-5).
You can not turn off the slave receiver until it display“-End” on the panel.
Down Loading Method
CABLE CONNECT MEASURES
1. CABLE CONNECT MEASURES:
a) Cable Layout
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
b) RS232 CABLE LAYOUT
# CONNECT TO P.C
# CONNECT TO SVR
c) Among wires from no.1 to 9 connect wire no.2 and 3 crossed to both
sides, and then connect the GROUND(GND) of terminal on P.C to
SVR, and then cut other wires.
Upgrade by Satellite
This function can upgrade the software of
your receiver through data sent by a
satellite. At the moment we offer satellite
updates only through ASTRA1 and Hotbird
satellites.
1. Select the satellite and TP or input the
TP value and download PID.
2. Then mark “Start” and press [Enter] to
begin the download of the upgrade.
This may need up to 60 minutes.
Therefore we suggest using of this function only if you don’t intent to watch
TV during this time.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operations
6.6 SatcoDX Auto Programming
This function is using the tables of the SatcoDX websites to update your
channel and satellite lists. You need a special application which is available on
the CD-ROM of the Tele-Satellite magazine. Install this software on your PC
first.
1. Start the SatcoDX application on your PC.
2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press
[OK]. The screen will show the message “OK to Proceed”.
3. Press [OK] again and you will see the message “Ready to Download”.
4. In the PC application set the baud rate to 115200 and start the download
procedure.
! Caution
The new download channels will delete the original channels list.
Please be careful before using it.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specification
7. Technical Specification
VIDEO
Decoding
Bit rate
MPEG-2 & MEPG-1 compatible
Max 15Mbps
Output
AUTO/PAL/NTSC
Aspect ratio
Active pixel
Output connector
4:3, 16:9, Auto
720x480 @ 30fps; 720x576 @ 25fps
RCA, TV SCART
AUDIO
Decoding
Mode
MPEG-2/MPEG-1 layer I & II
Mono, Dual, Stereo, Joint stereo
Max 384Kbps
Bit rate
DEMODULATOR
Demodulation
Symbol rate
QPSK
SCPC/MCPC
Outer code
Inner code
Energy dispersion
RS (204, 188, 8)
ALL DVB rates
DVB-S recommendation
INPUT SIGNAL
Frequency
Input level
Channel bandwidth
Input socked
950MHz ~ 2150MHz
-65dBm ~ -25dBm
36MHz
F-type connector
RF MODULATOR
Input
Output
IEC 169-24 Male x 1
IEC 169-24 Female x 1
UHF
Band
TV Standard
Output Channel
PAL BG/I/DK, NTSC M
21~69(PAL), 14~83(NTSC)
LNB CONTROL
Power supply
13/18V (500mA max) with short circuit
protection
Polarized control
DiSEqC control
13/18V polarization (vertical/horizontal)
DiSEqC1.0, DiSEqC1.1 and DiSEqC1.2
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specification
MISCELLANEOUS
Supply voltage
100~240VAC 50/60Hz
Power consumption
Operation temperature
Storage temperature
Dimension (W x D x H)
Weight
30 watts max
+5 °C to +40 °C
-20 °C to +70 °C
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Texas Instruments Computer Monitor SWRU157D User Manual
Texas Instruments Projection Television 8100CB User Manual
TOA Electronics Portable Speaker HS 1200BT User Manual
Tokina Camera Lens F28 PRO FX User Manual
Toshiba Personal Computer P25 User Manual
True Fitness Elliptical Trainer CSX User Manual
Tunturi Tent C 900 User Manual
Ultra Products Battery Charger ULT31922 User Manual
Vizio Music Mixer D 55E User Manual
VTech Telephone 917ADX User Manual