MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards
ANSI/ATA 878
Minneapolis, MN 55344 USA
ARCNET® Coax Copper/Fiber Media Converter
AR-CF-02, AR-CF-02(SC), AR-CF-02(SM)
Delay
300ns one-way
4.75" x 3.0" x 1.0"
Case dimensions
Shipping Weight
Environment
(119mm x 76mm x 25mm)
2 pounds
(0.9 kilograms)
Temperature:
Humidity
Altitude
0-40°C (32° to 104° F )
10-90%, non condensing
0-10,000 feet
USER’S GUIDE
The TRANSITION Networks ARCNET® Coax Copper/Fiber Media Converter
(AR-CF-02) extends the signal distance of an ARCNET® segment or node
link up to 2 kilometers over fiber*, up to 600 meters over coax cable in a star
topology, and up to 300 meters over coax cable in a bus topology.
Warranty
Five years
Power Supply Requirements Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 0.2 A).
A switch on the media converter allows the media converter to be used to
terminate the link or node signal.
TN PN
3525
3525
3518
3514
3525
Requirement
Location
United Kingdom
Europe
USA/Canada/Mexico
Japan
Australia
240 volts, 50 hertz
230 volts, 50 hertz
120 volts, 60 hertz
100 volts, 50-60 hertz
240 volts, 50 hertz
AR-CF-02
Provides a BNC
connector to coaxial
cable and a set of RX
(receive) and TX
NOTE: This product also can be powered by the Transition Networks E-MCR series media
converter rack.
(transmit) ST connectors
to multimode fiber-optic
cable.
Compliance Information
UL Listed
AR-CF-02(SC)
AR-CF-02(SM)
C-UL Listed (Canada)
CISPR/EN55022 Class A
Provides a BNC connector to
coaxial cable and an RX (receive)
and TX (transmit) SC connector to
multimode fiber-optic cable.
Provides a BNC connector to
coaxial cable and an RX (receive)
ST and TX (transmit) SC connector
to singlemode fiber-optic cable.
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
STATUS LEDS
Power
Coax
Steady green LED indicates connection to external AC power.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Blinking green LED
Power
TX
RX
indicates network
traffic on coaxial cable
link.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Coax
Fiber
Fiber
Blinking green LED
indicates network traffic on fiber link.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
*Consider carefully the network constraints imposed by the maximum latency
response time of installed equipment. Some equipment cannot handle the extended
Trademark Notice
ARCNET is a registered trademark of Datapoint Corporation.
All registered trademarks and trademarks are the property of their respective owners.
response time that 2 kilometers of fiber introduces.
Download from Www.Somanuals.com. All Manuals Search And Download.
33095.B
|