M900S™
900 MHz Wireless Broadband System
USER MANUAL
March 24, 2005
Revision C
for Firmware Version 1.3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Figures
Trango
Table of Figures
Figure 1: Typical Deployment....................................................................................................................................... 1
Figure 2: Basic Components of an M900S Radio.......................................................................................................... 3
Figure 3: Bottom of Radio............................................................................................................................................. 3
Figure 4: Back of Radio................................................................................................................................................. 4
Figure 5: Side of Radio & Location of Reverse Polarity SMA Connector .................................................................... 4
Figure 6: Wiring Diagram.............................................................................................................................................. 5
Figure 7: LED Summary.............................................................................................................................................. 15
Figure 8: LED and Reset Button Window................................................................................................................... 15
Figure 9: M900S Mounting Hardware Assembly........................................................................................................ 28
Figure 10: Alternative Mounting ................................................................................................................................. 29
Figure 11: Articulation for M900S with Mono Pod Mount (not supplied).................................................................. 30
Figure 12: Grounding of the Radio.............................................................................................................................. 30
Trango Broadband Wireless — M900S User Manual Rev. C
page iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
This manual covers basic configuration and installation of the M900S Wireless Broadband System and applies to
the following radio part numbers:
M900S-AP
900 MHz Access Point
M900S-SU
M900S-SU-EXT
900 MHz Subscriber Unit with integrated antenna and connector for external antenna
900 MHz Subscriber Unit with connector for external antenna (no integrated antenna)
FCC Information
This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and radiates radio-frequency energy; if not installed and
used in accordance with these instructions, the unit may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to correct the interference by one of more of the following measures:
1) Reorient the antenna.
2) Increase the separation between the affected equipment and the unit.
3) Connect the affected equipment to a power outlet on a different circuit from that which the receiver is
connected to.
4) Consult the dealer and/or experienced radio/TV technician for help.
FCC ID: NCYM900S
Canada:
IMPORTANT NOTE: Intentional or unintentional changes or modifications must not be made unless under the
express consent of the party responsible for compliance. Any such modifications could void the user’s authority to
operate the equipment and will void the manufacturer’s warranty. To comply with FCC RF exposure requirements,
the following antenna installation and device operating configurations must be satisfied. The antenna for this unit
must be fixed and mounted on an outdoor permanent structure with a separation distance of at least two meters
from all persons. Furthermore, it must not be co-located or operated in conjunction with any other antenna or
transmitter.
Warranty Information
Radios from Trango Broadband Wireless are warranted from one year from date of purchase. Please see
www.trangobroadband.com for a complete description of warranty coverage and limitations.
Firmware Notifications
To receive email notifications regarding firmware upgrades and product announcements, register at
Trango Broadband Wireless — M900S User Manual Rev. C
page iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Section 1 Introduction
Your Trango Broadband M900S radio system provides a reliable and robust means to deliver broadband access to a
wide geographic region through wireless Ethernet connectivity. This section will familiarize you with basic
operational concepts, as well as an overview of the various components and hardware of the M900S system.
Overview
The M900S is a highly versatile and cost effective outdoor point-to-multipoint solution for wireless broadband
service providers’ enterprise connectivity applications. The M900S delivers 3 Mbps over the air, and operates in the
900 MHz license free ISM band. Each radio includes an integrated dual polarized (horizontal and vertical) antenna,
as well as a connector for the attachment of an external antenna, such as a Yagi or an omni style antenna. Note: If
you are going to install an external antenna, refer to the M900S Professional Installation Guide. Contact
Technical Support for access to the Professional Installation Guide.
The M900S system consists of two types of radios: Access Points (APs) and Subscriber Units (SUs). Up to 126
subscriber units can be supported by a single AP, which acts as a hub in a star configuration. The AP delivers
wireless broadband service (Ethernet connectivity) to one or more SUs according to a proprietary adaptive dynamic
polling algorithm called SMARTPolling™. Network operators can co-locate multiple APs at a single cell site, thus
increasing the aggregate throughput available at each wireless point of presence (POP).
Figure 1: Typical Deployment
The AP typically resides at the center of the point-to-multipoint (PMP) network. It performs all management
functions, including the allocation of bandwidth for all associated SUs. The M900S AP provides a host of
comprehensive tools and functions.
The M900S system is classified as a Layer 2 multi-point bridge, thus all forms of Ethernet traffic will pass
seamlessly over the system. There is no limitation on the number of IP addresses or hardware devices to which an
individual subscriber unit may be connected.
Authentication of Subscriber Units is performed using a secure proprietary method, which is based on the MAC
address of the subscriber units. In order to establish a wireless link, the MAC address of the SU must be present in
the Access Point’s SUDB.
Both APs and SUs are IP addressable and can be managed remotely across the network. Users can manage the
radios using the telnet command line interface or the graphical HTTP browser interface. The M900S also provides
remote firmware upgrade capability utilizing TFTP. APs include a full-featured SNMP agent for the monitoring
and controlling of both APs and SUs via SNMP.
The M900S radios are powered using "power-over-Ethernet" for ease and low-cost installation. A single Cat-5
cable caries both Ethernet and DC power to the radio.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Both APs and SUs feature a handy "site survey" tool to check for interference, as well as RSSI tools for optimizing
antenna positioning. The M900S also features variable receiver threshold, full power control, dual polarized
antennas, and various link diagnostic tools.
SmartPolling™ & Bandwidth Throttling
One of the major advantages of the M900S system is the ability of the AP to handle multiple SU
connections and share the 3 Mbps data throughput efficiently. Bandwidth allocation is managed by the
AP’s SMARTPolling algorithm according to provisioning rules set up by the system administrator. The
AP polls each SU in a round robin format to determine if the SU has data to transfer. The SU only
transmits the data “upstream” to the AP when the AP gives authorization via a “transmit grant.” The SU
passes every “downstream” data packet from the AP and identifies packets intended for it. In order for an
SU to communicate with an AP, the system administrator must first add the MAC address and ID number
of the SU to the SUDB in the AP. The SmartPolling algorithm will poll active SUs more often, thus
making the most efficient use of the 3 Mbps bandwidth. Several other parameters are considered in the
SmartPolling algorithm including upstream/downstream committed information rate (CIR),
upstream/downstream maximum information rate (MIR), and Priority Setting.
Each of the above parameters is set in the AP by the system administrator and cannot be controlled at the
SU. These parameters will be covered in greater detail later in this text.
When power is first applied to a properly installed SU, it will scan all available channels listening for a
grant from an AP that has a matching Base ID and the SU’s MAC in the its SUDB. The SU will then stop
on that channel and respond to the AP using maximum RF power. Before the AP can add the SU to the
polling list, it must authenticate the SU by verifying the MAC address and performing a ranging operation
to the SU. Upon successfully locating and ranging the SU, the AP will then add the SU to the normal
polling list. Once the AP is regularly polling the SU, the SU is said to be “associated” to the AP.
Once associated, the AP will send a command to the SU to adjust the SU’s RF transmit power based on the Target
RSSI parameter set in the AP. This process is referred to as “power leveling”.
System operators may limit allowable bandwidth to specific customers utilizing the built-in CIR and MIR settings
(measured in kbps) for each SU.
Auto-retransmit Feature (ARQ)
The M900S features ARQ or “Automatic Request for Re-transmission,” which is the ability to correct for missing
or corrupted packets of data by requesting the sending radio to re-transmit the data. Both the AP and SU units
implement a form of ARQ known as “ARQ with Selected Repeat.” The use of ARQ is especially important in
areas of high interference. The ARQ feature can be turned on or off.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Overview
Section 2 Hardware Overview
This section provides details about each radio in the M900S family. The M900S-SU and M900S-AP include built-
in, electronically switchable, dual-polarized antennas, as well as a reverse polarity SMA connector for the
attachment of an external antenna. The M900S-SU-EXT features an external antenna connector and does not
include the integrated antenna. All units are designed for outdoor installation, and are powered by power-over-
Ethernet (POE) for ease of installation. The M900S Access Point, as well as the M900S subscriber units, provide
channels of operation within the 900 MHz ISM band that spans from 902 MHz to 928 MHz. The channel width is
6 MHz, and the default channel assignments allow for 4 non-overlapping channels.
M900S AP and SU Hardware Components
Each radio comes equipped with a power-over-Ethernet (PoE) J-Box, an AC adapter, and mounting hardware.
Radio (MU or RU) antenna
Power Supply (120 VAC-24 VDC)
J-Box (Power-over-Ethernet Injector)
4X
Mounting Hardware
8X
2X
Figure 2: Basic Components of an M900S Radio
Figure 3: Bottom of Radio
At the bottom of the M900S are two access ports: a twist-on weatherproof cable port for RJ-45 Ethernet (and PoE),
and a translucent access cover plug over the unit’s diagnostic LEDs and reset button. The LEDs will be discussed
later in this text.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Trango Broadband Wireless
M9000S-AP
S/N: 00000XXXX
Rev. A
MAC: 00 01 DE 00 02 F3
FCC ID: NCYM900SAP
Canada: XXXXXXXXXX
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
Figure 4: Back of Radio
The radio’s model number, FCC ID, MAC ID, and Serial number, are located on the backside of the radio.
.600
6.300
Figure 5: Side of Radio & Location of Reverse Polarity SMA Connector
Section 3 Getting Started
This section explains how to power your radios, establish TCP/IP connectivity to the radios, as well as how to
access the HTTP browser and the command line interfaces.
Connections and Power
Connections and powering of the radios is the same for APs and SUs.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
•
•
Connect a Cat-5 (straight through) Ethernet cable (we recommend shielded twisted pair) between the ODU
(out door unit) port of the J-box and the RJ-45 connector on the radio. Note that this cable will carry
power-over-Ethernet (PoE).
If connecting to a COMPUTER, use a Cross-Over Ethernet cable from the NET port of the J-box to the
computer’s Ethernet port.
If connecting to a HUB, SWITCH, or ROUTER, use a Straight-Thru cable.
•
Plug the AC adapter into an AC outlet.
M900S (AP or SU)
NETWORK
OR
COMPUTER
INDICATES POWER TO RADIO
INDICATES POWER TO J-BOX
CAT-5
USE STRAIGHT-THRU CABLE
CAT-5
IF TO HUB, SWITCH, OR ROUTER
STRAIGHT-THRU CABLE
USE CROSS-OVER CABLE IF TO COMPUTER
AC POWER
24 VOLT POWER
SUPPLY
POWER-OVER-ETHERNET
J-BOX
Figure 6: Wiring Diagram
Both green LEDs on the J-box should be lit, indicating power is present at the J-box as well as the radio.
You are now ready to configure the radio via the Ethernet port.
Radio Management Concepts
Proper connections to the radios and careful IP/routing & planning will enable the network administrator to access
and manage the radios via TCP/IP remotely over the network. Radio management over TCP/IP can be performed
from computers connected to the Ethernet side of each radio. Computers connected to the AP can manage the SU
over the wireless connection. Computers connected to the SU can manage the AP, provided that switch 7 (TCP/IP
for SU) is enabled on the AP. Switches will be covered later in this text.
Opmode
To fully understand radio management of the M900S system, it is important to be familiar with the concept of
operation mode or “Opmode.”
Trango Broadband Wireless — User Manual M900S Rev. C
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
APs and SUs can be in one of two Opmodes (“ON” or “OFF”). When in Opmode “OFF,” the AP is not
transmitting and it is not attempting to associate with SUs. Alternatively, when in Opmode “ON,” the radio is
transmitting and is attempting to associate.
Several functions, such as the site survey function and the SU RSSI function, can only be performed while the radio
is in a particular Opmode. See Appendix A – Command Set Reference for a complete listing of commands, and the
appropriate Opmode(s) for each command.
Switch Settings
M900S firmware includes several “switches” that are used to set certain operational parameters of the radios.
Switch settings can be changed via the HTTP browser interface or the command line interface. For purposes of
radio TCP/IP management, the following four switches are important:
Switch 2 (SU) - TCP/IP access to SU from the AP’s side of the network requires that the SU’s switch 2 (SW 2 –
TCP/IP for AP) be ON. Default setting for SW 2 (from factory) is ON.
Switch 5 (AP and SU) – In order to utilize the radio’s HTTP Browser interface, switch 5 (SW 5 – Enable HTTP)
must be ON. Default setting for SW 5 (from factory) is ON.
Switch 6 (SU) - TCP/IP access from Ethernet port of SU requires that switch 6 (SW 6 – TCP/IP Service for
Ethernet Port ) be ON. Default setting for SW 6 (from factory) is ON. If SW 6 is OFF, TCP/IP access to SU
from it’s Ethernet port is possible only if the SU’s Opmode is “OFF.”
Switch 7 (AP) – TCP/IP access to AP from SU’s side of network requires that the AP’s switch 7 (SW 7 –
TCP/IP for SU) be ON. Default setting for SW 7 (from factory) is ON.
Passwords
In order to login to an M900S radio (either through telnet or through the web browser interface), the user must
know the IP address and password. Both APs and SUs feature two levels of passwords, Read Write (RW) and
Read Only (RO). Be sure to change both passwords (RW and RO) prior to deployment on a live network.
Passwords can be changed using the “password ro and password rw command in either the CLI interface or in the
command console of the browser interface.
Reset Button
Pressing the reset button will reset the radio’s IP address and password back to the factory defaults.
Default IP (192.168.100.100) Default Password (trango)
Browser Interface
The M900S (both AP and SU) features a convenient and easy-to-use web based configuration and management
tool. No additional software is needed on your computer other than a web browser. Most functions can be
performed using the browser interface, although several functions can only be performed via command line
interface (CLI). The browser interface also includes a Command Console page that allows the user to enter most
CLI commands without leaving the browser interface.
To use the browser interface, the following must be present:
•
•
•
•
An Ethernet connection between a PC and the radio
Ethernet PC connection with IP/subnet that is routable to the radio
SW 5 ON (default)
A web browser on the PC (i.e. Microsoft Internet Explorer)
In order to use the browser interface – simply connect the radio to a PC and type the radio’s IP address (default IP
address=192.168.100.100) into the web browser (i.e. Microsoft Internet Explorer). This will bring up the Login
page.
NOTE: Login pages for the AP and SU are similar.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Browser Interface Login Page
Type the password (default trango) and continue. This will bring up the radio’s System Information page.
Web Browser System Information Page
ꢀ Note: System Information page for the SU is similar and is covered in detail later in this text.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Primary Features and Pages of the Browser Interface:
Navigation Column: Each page features a navigation column that runs along the left-hand side of the page. The
model number of the radio is listed at the top of the navigation column. On the bottom of the navigation column is
the current status of the radio including its Base ID, current Opmode, channel, antenna selection, and frequency.
The navigation column also features links to each of the following pages:
System Information: This page shows most of the basic configuration parameters of the radio. It is the first page
shown after login.
Configuration: The essential parameters, such as Base ID, IP, Subnet, gateway, channel, and antenna polarization,
are set here.
Advanced Setup: The advanced RF parameters, such as transmit power, receiver threshold control, and channel
center frequencies, are set here.
Site Survey: With Opmode “Off” the user can conduct a spectrum analysis using this page.
Subscriber Database: This is the page for defining which SUs can associate to the AP.
Link Control: This page shows which SUs are associated. This page also provides several tools for evaluating the
quality of the wireless link.
Command Console: From this page, the user can run any console command that is not interactive (i.e. ipconfig)
or time sensitive (su linktest). For a complete list of console commands, type "help" or “?” in the entry field.
Logout: This link will end the current browser session with the radio.
Help: The Browser Interface features useful Help pages that explain all listed parameters. To access the Help
pages click on the Help link.
Command Line Interface
Although most radio functions can be managed via the browser interface, the command line interface (CLI)
provides slightly more functionality, and is usually the management tool of choice for experienced users. The CLI
can be accessed through Telnet.
Telnet
Open a command prompt (DOS) session on your PC. Open a Telnet session by typing:
telnet [ip address of radio]
All Trango radios are pre-configured at the factory with a default IP address of 192.168.100.100. The factory
default password is trango. Once you connect to the radio you will be greeted with the current hardware and
firmware information and prompted for a password. Type in the read-write (RW) password and press enter.
Example:
C:>telnet 192.168.100.100
Welcome to Trango Broadband Wireless M900S-AP 1p0H8005D04030101
Password:
#>
To terminate a CLI session (Telnet or Serial) type the command logout.
ꢀ Note: Type help or ? for a listing of all the CLI commands. Type help <command>, for the syntax of a
particular command.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Example (to view a list of all commands which start with su)
#> ? su
su [all | <suid, 1..126>]
su info <suid, 1..126>
su linktest <suid, 1..126>
su password <suid|all> <rw|ro> <new password> <new password>
su ping <suid, 1..126>
su reboot <suid|all>
su sw <suid|all> <sw#, 0..7> <on | off>
su testrflink <suid, 1..126> <r>
su testrflink <all> <r>
sudb add <suid, 1..126> <pr|re> <device id,hex>
sudb cirmir <<suid>|all> <cir dn> <cir up> <mir dn> <mir up>
sudb defaultcirmir [<cir dn> <cir up> <mir dn> <mir up>]
sudb delete <<suid>|all>
sudb dload
sudb gid <<suid>|all> <0..15>
sudb view
survey <time, 1..10 sec> <antenna, h|v|e>
ꢀ NOTE: The majority of the CLI commands will be covered throughout this text as well as in Appendix A −
Command Set Reference.
Troubleshooting
If you can not telnet into the radio or open a browser session, check cable connections, ensure proper use of cross-
over vs. straight-through cable, and ensure PC’s subnet is routable to radio’s IP address. If you still cannot access
the radio’s management interfaces, consult the troubleshooting guide that is available at
www.trangobroadband.com in the Technical Support area of the website.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
Section 4 Basic Configuration via Browser Interface
This section describes a few more basic concepts, as well as how to establish a wireless link using the Browser
(HTTP) Interface. This section is written to address only the most basic steps in establishing a link in the lab or a
bench-top environment. It is highly recommended that you read the other sections of this manual to gain an
understanding of all important configuration parameters and procedures prior to deploying your equipment.
In this section you will:
•
•
•
•
•
•
Learn about AP and SU Basic Configuration Screens and Parameters
Populate the AP’s Subscriber Unit Data Base (SUDB) with at least one SU
Configure Other Basic AP Parameters
Configure Basic SU Parameters
Establish a Wireless Link
Evaluate Link Quality
The M900S uses the concept of “association” to indicate that the APs and SUs are communicating. If all
parameters are properly set, the AP will begin actively searching for the SUs in its SUDB. Once an active SU is
detected, the authentication and association process will begin.
Essentials for Establishing a Wireless Link with M900S Series Radios
•
•
•
•
•
•
Base ID in AP and SU must match
MAC Address of SU must match an entry in the SUDB
SU must be set to “autoscan” all channels, or it’s channel must be fixed on the same channel as the AP
AP must be in Opmode “ON”
SU must be in Opmode “ON”
Adequate signal strength must be received at each radio
If all of these parameters are met, the wireless link will automatically establish itself and Ethernet traffic will begin
to pass between the radios.
ꢀ Note: This section utilizes the Browser Interface as the configuration tool. For the equivalent procedure using
CLI commands, see Section 5.
Configuring the AP’s Subscriber Unit Database (SUDB)
Prior to establishing a wireless link, the user must configure the SUDB in the AP with each SU’s MAC address and
related settings. The SUDB includes information about each SU. Click on the Subscriber Database page to add,
modify, and delete SUs. The key information for each SU includes the following:
SU ID:
TYPE:
User Definable subscriber unit ID (1…126)
PR Priority or REG Regular. Priority SUs are polled much more frequently than regular SUs.
Priority SUs in general will respond to the AP with less latency than regular SUs.
Group:
SU to SU Group # (1..F in hex) for SU to SU communications within the same sector. Note:
This SU to SU feature allows interconnectivity between multiple SU’s in the same sector,
without the need for a router. Only SUs with the same SU to SU group # may communicate
with each another. If you do not want the SUs to communicate with each other, choose N/A
for SU to SU group. In order to use SU to SU communication, AP switch #3 must be ON.
The default setting for switch #3 is OFF.
CIR UP:
Committed Information Rate from SU to AP. Minimum upstream data rate (measured in
Kbps) at which the SU will attempt to deliver bandwidth to the AP. Maximum setting is
3000.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
CIR DOWN:
MIR UP:
Committed Information Rate from AP to SU. Minimum downstream data rate (measured in
Kbps) at which the AP will attempt to deliver bandwidth to this SU. Maximum setting is
3000.
Maximum Information Rate from SU to AP. Maximum upstream data rate (measured in
Kbps) at which the SU will attempt to deliver bandwidth to the AP. Maximum setting is
3000.
MIR UP:
Maximum Information Rate from AP to SU. Maximum data rate (measured in Kbps) at
which the AP will attempt to deliver bandwidth to this SU. Maximum setting is 3000.
DEVICE ID:
MAC address of the SU.
Creating an SU in the SU Database.
1. Connect to the AP (see Getting Started) and open the Subscriber Database page.
2. Enter SU ID (range 1 – 126).
3. Select either PRIORITY or REGULAR.
4. If SU will be part of an SU to SU group, enter the SU to SU group number.
5. CIR up: (SU to AP Committed Information Rate) – minimum upstream bandwidth for the SU in Kbps.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
6. CIR dn: (AP to SU Committed Information Rate) – minimum downstream bandwidth for the SU in Kbps.
7. MIR up: (SU to AP Maximum Information Rate) – maximum upstream bandwidth for the SU in Kbps.
8. MIR dn: (AP to SU Maximum Information Rate) – maximum downstream bandwidth for the SU in Kbps.
9. Enter Device ID (MAC Address of the SU).
10. Save and Activate changes.
Important! Always remember to Save and Activate changes, or the SUDB will revert back to its previous
state after a power cycle or reboot.
Important! SUs using SU to SU communication must be on the same subnet.
!
!
Configure Other Basic AP Parameters
In addition to setting up the SU in the SUDB, the following settings in the AP’s Configuration page must be set (or
left at default).
Base ID:
Four character, alphanumeric, user definable base station ID. Input of BASEID shall be in the
format of xxxx. Where x is any character from the set: {0..9; a..z; A..Z; '!@#$%^&*()_+[]\<>,./?'}.
The Base ID is typically assigned to a single AP or a group of APs at a particular cell site. The
Base ID in the AP must match the Base ID in the SU in order for a link to be established. This
parameter can only be changed while in Opmode "OFF."
AP ID:
User definable AP ID (00-FF). Default is last two digits of MAC ID. One authenticated, the AP
will automatically assign its AP ID to the SU. This parameter can only be changed while opmode
is “OFF”.
IP Address, Subnet Mask, Gateway:
The IP configuration of the radio. Used for configuration and network management purposes.
Since this is a layer-II device, these parameters do not play a role in the establishment of the
wireless link.
Default Opmode:
Operation mode of the radio after a power cycle or reboot. When the radio enters Opmode "ON," it
will be transmitting. When the radio enters Opmode "OFF," the radio will not be transmitting, but
can be accessed through the Ethernet port. The radio can be put into Opmode "OFF" regardless of
its default Opmode by telnetting into the radio within the first 30 seconds after a power cycle or
reboot.
Active Channel/Polarization:
The current channel and antenna polarization of the unit when in Opmode "ON."
To configure the AP’s other basic settings, complete the following steps:
1. Connect to the AP (see Getting Started) and open the Configuration page.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
2. Set Base ID, or choose the default Base ID of 0000. (Must match the SU.)
3. Set AP ID (00-FF HEX), or choose the default, which is last two bytes of MAC Address.
4. Set IP, Subnet, and Gateway, or leave at default settings. Keep in mind, if you change the IP Settings of
the radio, you will loose your HTTP session when you Save and Activate Settings.
5. Choose Active Channel (1-4).
6. Choose Antenna Polarization (H or V), or choose E for an external antenna. Only use E for M900S-SU-
EXT model.
7. Ensure default Opmode is "ON."
8. Save and Activate Settings.
9. If this is the first SU to be added to the SUDB, reboot the AP.
After reboot, the AP will automatically enter its default Opmode (ON) after approximately 40 seconds. At this time
it will begin actively searching for all SUs in its SUDB. Once an active SU is detected, the authentication and
association process will begin.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
Configure Basic SU Parameters
In order to establish a working link, the Base ID in the SU must match the Base ID set in the AP.
SU Basic Setup:
1. Connect to the SU (see Getting Started) and open the Configuration page.
2. Set Base ID. (Must match the AP.)
3. Set IP, Subnet, and Gateway, or leave at default settings. Keep in mind, if you change the IP Settings of
the radio, you will loose your HTTP session when you Save and Activate Settings.
4. Ensure default Opmode is "ON."
5. Save and Activate Settings.
6. If in Opmode “OFF,” click Activate Opmode.
At this point, if all parameters have been set correctly and the radios are within range, a wireless link between the
AP and SU will automatically become established. Once this occurs the SU will be in “associated” status.
Allow approximately 60 seconds for the radios to complete the boot-up cycle and to associate. If the
AP is busy servicing many SUs, the association process may take slightly longer.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
LED Summary
At this point it is useful to learn about the LEDs that can be found on the bottom of the radio. These LEDs can
assist the user in determining radio and link status.
ASSOCIATION LED (GREEN)
Blinking once every second in
Opmode "OFF" (AP and SU).
RSSI LEDs (YELLOW) - In all modes except "Survey,"
the unit's four yellow LEDs indicate the level of RF
signal being received from a valid AP.
Twice per second Opmode "ON" and
scanning for an AP (SU Only).
Yellow LED 1 (rightmost): On when RSSI > -85 dBm
Yellow LED 2 : On when RSSI > -75 dBm
Yellow LED 3 : On when RSSI > -65 dBm
Yellow LED 4 (leftmmost): On when RSSI > -55 dBm.
Solid after unit is associated with an
AP (SU Only).
In addition, these 4 LEDs will flash once to indicate the
'factory reset' button has been activated.
Solid after unit is in Opmode "ON" (AP
Only).
RESET BUTTON - resets IP and
password to factory default
ACT LED (RED) - Ethernet Activity Light
10/100 Link LED (GREEN) -
Illuminated when link speed is
negotiated at 100 BaseT. It is off
when link speed is 10 BaseT or not
connected.
Figure 7: LED Summary
LED / RESET BUTTON WINDOW
Figure 8: LED and Reset Button Window
Trango Broadband Wireless — User Manual M900S Rev. C
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
Link Control Page
The radio’s firmware includes several useful tools to assist in determining which SUs are associated and the quality
of each link. One method for verifying link quality is by using the Link Control page.
On this page the user can immediately see which SUs have associated. In the page shown, SU ID# 1 is associated,
and SU ID 17 is not. Consider "Power Off" status synonymous with "not associated."
RF Link
Loopback Test
The RF Link Loopback test
is one of the built-in tools
for evaluating the quality
of the wireless link.
Specify an SU ID and time
in minutes to conduct the
test. The test is prioritized,
so it will take precedence
over all other traffic. 1600
byte packets are sent and
received between the SU
and AP at 50 millisecond
intervals over the time
specified.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
SU Ranging Test
This test reports the SU’s
distance from the AP in miles,
received signal strength for
uplink and downlink, and SU Tx
Power. Use a link budget calculator to analyze results.
Advanced Setup Page
The Advanced Set up page includes several important parameters including RF TX Power, RF RX Threshold,
Target RSSI from SU (AP only), and Channel Table.
RF TX Power:
Sets the conducted RF power output of the radio. Highest allowable setting is 26 dBm.
Lowest setting is –4 dBm. This value does not include antenna gain. A higher number is
more powerful.
RF RX Threshold:
Sets the receive threshold of the radio. The radio will not process signals received below
this level, so it is very useful for interference mitigation. For a smaller radius of
operation use a higher threshold (-75 is higher than -80).
Target RSSI from SU: Used by the powerleveling process to automatically adjust the RF output power level of
all SUs in a sector so the signal strength from each SU as measured at the AP will be
roughly equal.
Channel Table:
Assigns channel numbers to actual frequencies of operation. Default settings allow the
largest number of channels (4) within the band, while still maintaining 6 MHz channel
spacing.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
Other Key Parameters
This section describes the remainder of the parameters listed on the System Information page. Most of these
parameters are the same for both APs and SUs.
Hardware Version: Hardware version is factory-set and cannot be changed by the user.
FPGA Version: Low-level field programmable gate array firmware currently loaded on the radio. Normally the
FPGA firmware will not require upgrading.
Firmware Version: Main firmware. In this example, the version part of the string is 0p1 (v0.1) , the hardware
code is H8005, and the remainder of the string is a date code.
Device ID: MAC address of the radio.
S/N: Serial number of the radio.
Telnetd Port: User changeable telnet port of radio.
TFTPd: Current status of TFTP daemon. Used for uploading firmware.
MIR Threshold: Enable/Disable the Maximum Information Rate (MIR) Threshold. The MIR Threshold is the
aggregate throughput on the AP at which the AP will start to enforce CIR rules for SUs.
Active Channel: The channel currently being used by the radio.
RFRX Threshold: Sets the receive threshold of the radio. The radio will not process signals received below this
level, so it is very useful for interference mitigation. For a smaller radius of operation use a higher threshold (-65 is
higher than -70).
Broadcast Packet: This software switch (0) enables/disables the blocking of Ethernet control packets, except
ICMP and ARP, to reduce the amount of unnecessary overhead introduced into the wireless link.
SU to SU Communication: If enabled (via switch 3), SUs with matching SU to SU groups (except group 0) can
communicate in peer-to-peer mode via the AP without the need for a router behind the AP.
TCP/IP Service for SU: If enabled, the AP can be accessed via TCP/IP (Telnet or HTTP) from the SU side of the
network via the wireless link.
Remarks: User definable radio information (i.e. customer name, address of installation, etc). A maximum of 28
characters can be stored.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via Browser Interface
Site Survey Page
The Site Survey page provides a useful tool for detecting and measuring interference. The radio must be in
Opmode “OFF” in order to use this feature.
Enter the number of minutes desired for the survey, and select the polarization H, V, or E (for an external antenna).
Click "Start Survey." A survey of the default 4 channels will be performed. Results are reported in dBm per
channel as average and peak. A channel is reported to be "Clear" if the peak and average are below the RF RX
Threshold by more than 8 dB.
Trango Broadband Wireless — User Manual M900S Rev. C
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
Section 5 Basic Configuration via CLI
This section covers how to utilize the radio’s CLI interface to establish a working wireless link.
In this section the most basic settings using the CLI are discussed. Topics include:
•
•
•
Access Point Basic Settings
Subscriber Unit Database Settings
Subscriber Unit Basic Settings
See Appendix A − Command Set Reference for a complete listing of the CLI commands.
See the “Getting Started” section for a description of how to access the radio via Telnet or Serial Interface.
Access Point Basic Settings
After logging into an AP or SU, it is good practice to type the sysinfo command to see the radio’s basic system
information. Example (Access Point):
#> sysinfo
[Hardware Version] 8005
[FPGA Version] 03121104 [Checksum] 75930BDC
[Firmware Version] AP 1p0a2H8005D04010603 [Checksum] AE5D873F
[Device ID] 00 01 DE 15 5C D0 [S/N] 01400016
[Base ID] 1234 [AP ID] 01
[System Up Time] 0 day(s) 00:29:56
[Opmode] on [Default Opmode] on
[IP] 10.8.0.254 [Subnet Mask] 255.255.255.0 [Gateway] 10.8.0.1
[Httpd Port] 80 [Httpd Status] listen
[Telnetd Port] 23 [Telnetd Status] connected (10.8.0.62,1146)
[Tftpd] disabled
[RF Tx Power] -4 dBm
[RF Rx Threshold] -98 dBm
[MIR Threshold] 3 Mbps
[Ch#01] 906 Mhz [Ch#02] 912 Mhz [Ch#03] 918 Mhz [Ch#04] 924 Mhz
[Default Channel] 1 h [Active Channel] 1 h
[Broadcast Packet] block [SU to SU] off [TCP/IP for SU] on
[Remarks]
[RF Rx] 0 kbps [RF Tx] 0 kbps [Eth Rx] 1 kbps [Eth Tx] 0 kbps
Many of these parameters can be changed by the user. A description of each of these changeable parameters, along
with the related command, is shown in the table below.
Important! When changing settings, it is usually necessary to type the save ss command in order to update
the radio’s flash memory. If you do not type the save ss command, the setting will be lost the next time the
!
radio is rebooted or power cycled.
.
AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter
Device ID
Base ID
Description
Related CLI Command
N/A
set baseid <baseid>
MAC Address of AP
Specifies the cell or cluster to
which the AP belongs. Base ID
must match in AP and SU in
order to establish a wireless
link.
Example:
#>set baseid aa12
Trango Broadband Wireless — User Manual M900S Rev C
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter
Description
Related CLI Command
AP ID
This parameter provides a
unique number for each AP. If
Target AP is specified on SU,
the SU can only authenticate
with the specified AP. The
default AP ID is the last two
bytes of the MAC address.
Current Opmode of the radio.
set apid <apid> (00-FF in HEX)
Example:
#>set apid 33
Opmode
opmode on y
This sets the radio to Opmode “ON.” If the radio is
accessed via the Ethernet port within the first 30
seconds after reboot/power cycle, the Opmode will
default to “OFF.”
Default Opmode
Determines the Opmode (“ON” set defaultopmode <on or off>
or “OFF”) of the radio after
reboot/power cycle. When this Example:
#>set defaultopmode on
parameter is set to “ON,” the
radio will progress into
Opmode “ON” automatically
after a reboot/power cycle.
Determines the amount of time
the radio will remain in
Opmode “OFF” after
Opmode Start
set defaultopmode on [<time (sec)>]
Example:
#>set defaultopmode on 60
reboot/power cycle before
progressing to the default
Opmode.
IP
Subnet
Gateway
IP, Subnet, and Gateway
address of the radio.
ipconfig [<new ip> <new subnet mask> <new
gateway>]
Example:
#>ipconfig 10.1.1.2 255.0.0.0 10.1.1.1
TFTPD Status
TFTPD status (on or off).
TFTPD should be turned on to
import a file into the radio
(such as new firmware).
tftpd [<on|off>]
Example:
#>tftpd on
Default is off. TFTPD will
revert to Off after rebooting.
Trango Broadband Wireless — User Manual M900S Rev C
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter
Description
Related CLI Command
MIR Threshold (Kbps)
User specified MIR Threshold.
To specify total throughput
mirth [<0..3, Mbps>]
level that the AP will serve only Example:
#>mirth 2
CIR (committed information
rate) to associated SUs.
When MIR Threshold is
disabled, the AP will serve MIR
for all its SUs.
When MIR Threshold is
activated, and the network
traffic exceeds the MIR
Threshold, the AP will only
serve CIR for all its SUs.
When MIR Threshold is
activated, and the network
traffic does NOT exceed the
MIR Threshold, the AP will
still serve MIR for all its SUs.
Current RF channel
Active Channel
Antenna
freq [<ch#>]
Example:
#>freq 3
This command will change the channel of the AP to
3.
antenna [<v|h|e>]
Current antenna selection:
(h)horizontal, (v)vertical,
(e)external
Note: With the M900S-SU-
EXT, only the (e) external
antenna is functional.
RF RX Threshold
Specifies the receiver
rfrxth <-90|-85|-80|-75|-70|-65>
example:
#>rfrxth –70
sensitivity of the AP. It is a
powerful tool when the radio is
in a noisy environment. AP
will block out any signal
received which is below the RF
Rx threshold. Separate settings
exist for both ISM and UNII
bands.
RF TX Power
Channel Table
Current transmit power of the
AP not including antenna gain.
power <set> <min|max|<dBm>
Example:
#>power set 10
freq writechannel [<ch#> <freq>]
Example:
#>freg writechannel 3 910
Assigned frequencies to
channels. All channels may be
re-assigned as desired by the
administrator.
This command will change channel 3 to 910 Mhz.
Broadcast Packet Filter
This software switch (0)
sw 0 [<on|off>] (default is on)
enables/disables the blocking of Example:
#>sw 0 on
Ethernet control packets, except
ICMP and ARP, to reduce the
amount of unnecessary
overhead introduced to the
wireless link.
note: All switch settings (0-7) are set using the sw #
[<on/off>] command.
SU to SU
This software switch (3)
sw 3 [<on|off>] (default is off)
Trango Broadband Wireless — User Manual M900S Rev C
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter
Description
Related CLI Command
Example:
#>sw 3 on
enables/disables the SU to SU
feature. When SU to SU is
turned on, multiple SU’s within
the same sector (meaning
associated to that AP) can
communicate with each other,
provided they have the same
SU2SU group number.
TCP/IP for SU
Remarks
This software switch (7) when
on, allows users on the SU side Example:
of the network to telnet or
HTTP into the AP.
User definable radio
information (i.e. customer
name, address of installation,
and so on). A maximum of 28
characters can be stored.
sw 7 [<on|off>] (default is on)
#>sw 7 off
remarks [<remarks>]
Example:
#>remarks 123 Elm Street
Subscriber Unit Database (SUDB) Settings
Once you are familiar with the basic system information presented above, you are ready to add one or more SUs to
the SUDB. There are five basic commands related to the SUDB: sudb add, sudb cirmir, sudb defaultcirmir, sudb
view, and save sudb.
Adding an SU
To add an SU to the database, you will need to know the following information:
1. MAC ID of the SU (printed on the back of the SU).
2. Polling priority, either PRIORITY or REGULAR.
ꢀ Note: SUs designated as PRIORITY will get polled more often by the AP.
To add an SU to the database, use the following command and syntax:
sudb add <suid> <pr|reg> <device id>
suid: SU ID
pr: priority user
reg: regular user
<device id>: xx xx xx xx xx xx in hexadecimal (this is the MAC address of the SU)
Example:
#>sudb add 5 pr F3 3C 50 67 89 D4
In this example an SU #5 was added as a Priority SU . The MAC ID of the SU is F3 3C 50 67 89 D4.
ꢀ Note: You can add up to 126 entries in the SUDB.
CIR / MIR Commands
The default CIR/MIR setting is 3000 kbps for upstream and downstream.
To change the SU’s CIR/MIR settings, use the following command:
sudb cirmir <suid|all> <cir dn> <cir up> <mir dn> <mir up>
Trango Broadband Wireless — User Manual M900S Rev C
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
Example:
#>sudb cirmir 5 128 256 3000 3000
In this example, SU #5’s CIR downstream was set to 128, and its CIR upstream to 256. MIR upstream and
downstream were set to 3000.
To change the default CIR/MIR values, use the following command:
sudb defaultcirmir <default cir dn> <default cir up> <default mir dn> <default mir up>
Example:
#>sudb defaultcirmir 256 256 512 512
To view the entries in the SUDB, type the command sudb view.
To save the changes you have made to the SUDB, type save sudb.
Other important SUDB related commands are sudb delete and sudb modify. See Appendix A for a descriptions of
these commands.
Important! After updating the SUDB, type the command save sudb to save your changes. If you do not
save, the SUDB file will revert back to its previous state after power cycle or reboot.
!
Subscriber Unit Basic Settings
Login to the SU. To receive a comprehensive snapshot of the system’s configuration info and status, type the
command sysinfo.
#> sysinfo
[Hardware Version] 0005
[FPGA Version] 03121104 [Checksum] 75930BDC
[Firmware Version] SU 1p0a2H0005D04010603 [Checksum] F4658C90
[Device ID] 00 01 DE 16 E3 7F [S/N] 01500031
[Base ID] 1234 [AP ID] 01 [SU ID] 1
[System Up Time] 0 day(s) 00:37:02
[Opmode] on [Default Opmode] on
[IP] 10.8.0.245 [Subnet Mask] 255.255.255.0 [Gateway] 10.8.0.1
[Httpd Port] 80 [Httpd Status] listen
[Telnetd Port] 23 [Telnetd Status] connected (10.8.0.62,1147)
[Tftpd] disabled
[RF Tx Power] -4 dBm
[RF Rx Threshold] -98 dBm
[Ch#01] 906 Mhz [Ch#02] 912 Mhz [Ch#03] 918 Mhz [Ch#04] 924 Mhz
[Default Channel] 1 v [Active Channel] 1 h [Associated] Y
[Broadcast Packet] block [Auto Scan AP] on [TCP/IP for AP] on [TCP/IP for Local
Eth]on
[Remarks]
[RF Rx] 3 kbps [RF Tx] 3 kbps [Eth Rx] 0 kbps [Eth Tx] 0 kbps
[ARQ RF Tx Retry] 197 [ARQ RF Tx Retry Maxed Out] 0
Many of these parameters can be changed by the user. A description of each of these changeable parameters, along
with the related command, is shown in the table below.
Important! When changing settings, it is usually necessary to type the save ss command in order to update
the radio’s flash memory. If you do not type the save ss command, the settings will be lost the next time the
radio is rebooted or power cycled.
!
Trango Broadband Wireless — User Manual M900S Rev C
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
Trango Broadband Wireless — User Manual M900S Rev C
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
SU Parameter
Device ID
Base ID
Description
MAC Address of the SU
Specifies the cell or cluster to set baseid <baseid>
which the SU belongs.
Related CLI Command
N/A
Example:
#>Set baseid aa12
Target AP
If unique AP ID selected, the targetap <apid>
SU can only associate with
the specified AP. If ALL is
selected, the SU can
associate with any AP with a
matching BASE ID.
Examples:
#>targetap 33
#>targetap all
Opmode
Current Opmode of radio.
opmode on y - set Opmode to “ON.” (note: “y”
is necessary if default Opmode is “OFF.”)
opmode off – set Opmode to “OFF.”
Default Opmode
Determines the Opmode
(“ON” or “OFF”) of the radio
after reboot/power cycle.
When this parameter is set to
“ON,” the radio will progress
into Opmode “ON”
set defaultopmode <on or off>
Example:
#>set defaultopmode on
automatically after
reboot/power cycle.
IP
Subnet
Gateway
IP, Subnet, and Gateway
address of radio.
ipconfig [<new ip> <new subnet mask> <new
gateway>]
Example:
#>ipconfig 10.1.1.3 255.0.0.0 10.1.1.1
TFTPD
TFTPD status (on or off).
TFTPD should be turned on
to import a file into the radio
(such as new firmware).
Default is off. TFTPD will
revert to off after
tftpd [<on|off>]
Example:
#>tftpd on
reboot/power cycle.
RF TX Power
Current transmit power of the Informational Parameter – can not be manually
SU not including antenna
gain. This is controlled by
the AP.
changed by user.
Active Channel
Shows the channel used in
the current association, and
"Associated" or
"Disconnected" depending
on the association status.
If Autoscan AP (SW 1) is on, the active channel
(and antenna selection) will be set once the SU
scans and begins the association process with an
AP.
If Autoscan AP is off, the active channel is set by
the user, using the freq command.
freq [<ch#> <v|h>]
Example:
#>freq 3
This command will change the channel of the AP to
3. Use the antenna command to select an antenna
Trango Broadband Wireless — User Manual M900S Rev C
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Configuration via CLI
SU SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
SU Parameter
Description
Related CLI Command
polarization.
antenna [<h | v |e>]
sw 0 [<on|off>]
Broadcast Packet Filter
This software switch (0)
enables/disables the blocking
of Ethernet control packets,
except ICMP and ARP, to
reduce the amount of
Example:
#>sw 0 on
unnecessary overhead
introduced into the wireless
link. Default setting is ON.
AP Autoscan
This software switch (1) is to sw 1 [<on|off>] (default is on)
turn AP autoscan on or off.
TCP/IP for AP
This software switch (2)
when on, allows users at the
AP side of the network to
telnet or HTTP into the SU.
sw 2 [<on|off>] (default is on)
Example:
#>sw 2 off
TCP/IP for Local
Ethernet Port
This software switch (6)
when on, allows users on the
wired side of the SU to telnet
or HTTP into the SU
sw 6 [<on|off>] (default is on)
regardless of the Opmode.
Remarks
User definable radio
remarks [<remarks>]
Example:
#>remarks 678 Oak Ave
information (i.e. customer
name, address of installation,
and so on). A maximum of
28 characters can be stored.
This is an average of wired
and wireless, transmit and
received traffic in kilobits per
second.
Counters:
RF TX RF RX
Eth TX Eth RX
Informational Parameter
Trango Broadband Wireless — User Manual M900S Rev C
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hardware
Section 6 Mounting Hardware
1
2
3
4
Not Supplied
5
ITEM
PART NUMBER
QTY.
NO.
1
1
4
8
2
Radio
2
3
4
#10 x 3" Threaded Rod
#10 Keps Nut
"V" Bracket
5
Mono Pod Mount (Not Supplied)
1
Figure 9: M900S Mounting Hardware Assembly
Trango Broadband Wireless — User Manual M900S Rev C
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hardware
Alternate Mounting Configuaration
Not Supplied
5
1
2
3
4
ITEM
NO.
PART NUMBER
QTY.
1
2
3
4
1
4
8
2
Radio
#10 x 3" Threaded Rod
#10 Keps Nut
"V" Bracket
5
Mono Pod Mount (Not Supplied)
1
Figure 10: Alternative Mounting
Trango Broadband Wireless — User Manual M900S Rev C
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hardware
Standard Mounting
Alternative Mounting
U
p
/ D
o
w
n
T
i lt
Up/Down Tilt
4
X
M
u
s
t
B
e
l o
o
s
e
n
e
d
f
o
r
U
p
/ D
o
w
n
T
i lt
Figure 11: Articulation for M900S with Mono Pod Mount (not supplied)
Cabling and Grounding Considerations
Grounding Example
Proper mounting of the radio includes
considerations for grounding. Please note that
if the radio is attached to a metal pole that is
earth-grounded, no other grounding is
necessary. If the radio is not earth-grounded
via the mounting bracket, you must attach a
grounding wire to the grounding stud on the
back of the radio as in the adjacent diagram.
Figure 12: Grounding of the Radio
Trango Broadband Wireless — User Manual M900S Rev C
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hardware
Installation Notes
Access to the radio’s RJ-45 Port and LED status lights are purposely located at the bottom of the radio to minimize the risk of
water intrusion. Do not mount the radio upside down.
The J-Box is not a weatherized device, and must be located either indoors or in a weather-protected cabinet.
Shielded twisted pair Cat-5 cable is recommended for all installations unless the cable is placed in metal conduit.
The shield within the Cat-5 cable does not need to be grounded if the radio itself is grounded.
It is important to consider that most Cat-5 cable will deteriorate over time if exposed to the weather (especially direct
sunlight). Conduit (metal or PVC) is recommended to protect the cable.
Important! The Ethernet port compression washer should be loosely tightened around the cat-5 cable to
allow pressure equalization within the radio enclosure. Leave approximately 1 mm around the cat-5.
!
It is important to provide strain relief and a drip loop for STP Cat-5 cables. Do not mount the radio upside down.
Trango Broadband Wireless — User Manual M900S Rev C
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
Section 7 Deployment
Once you are familiar with the basic operation of the radios you are ready for deployment in the field. The deployment
process consists of the following steps:
•
•
•
•
•
Site Selection
Site Survey
Channel Planning
SU Antenna Alignment
Link Management Commands
Site Selection
Proper site selection for your AP will help ensure a successful deployment. Site selection will depend on a wide variety
of factors, but from the radio’s performance standpoint, please consider the following:
•
Path from AP to SU should provide as few obstructions as possible, thus it is advisable to place the AP as high as
possible on a tall building or tower.
•
•
•
•
Ethernet cable limit is 300 feet from Ethernet device (router, switch) to the radio.
Radios require grounding for optimal performance.
AP provides sector coverage of 60ºazimuth and 60º elevation.
Consider nearby sources of interference that could degrade the performance of the radio. Mount radios as far
from sources of interference as possible.
•
Perform a site survey to determine noise level and relative clarity of channels at chosen installation location.
Site Survey
Both the AP and SU provide a powerful on-board site survey tool. This tool will tell you if there is interference present in
the 900 MHz ISM band.
Command: survey <time> <antenna>
In order to use the survey command, the radio must be in Opmode “OFF.” The survey can be performed for up to 10
seconds per channel (incrementing by 2 MHz), and for the horizontal polarization, vertical polarization, or an external
antenna.
Prior to performing the site survey, place the radio in the installation spot and aim the radio in the desired direction.
After the specified period, the results of the test will provide you with a listing of each channel in the band, the average
signal received, and the maximum signal received during the survey period.
In general you will be looking for frequencies with interference signal strength of –85 dBm or lower. If interference is
present on various channels, it is recommended that you chose clean channels or alternate polarizations for your
deployment. If it is not possible to use a clean channel/polarization combination, there are various methods available to
mitigate the affects of interference. These methods include the use of the RFRX Threshold settings, or the use of external
shields and external narrower beam antennas.
Trango Broadband Wireless — User Manual M900S Rev C
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
Example:\
#> survey 2 v
Press [space] then [enter] to stop
880 MHz
882 MHz
884 MHz
886 MHz
888 MHz
890 MHz
892 MHz
894 MHz
896 MHz
898 MHz
900 MHz
902 MHz
904 MHz
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -98 dBm
peak -93 dBm avg -95 dBm
peak -92 dBm avg -92 dBm
peak -91 dBm avg -91 dBm
peak -90 dBm avg -90 dBm
peak -91 dBm avg -92 dBm
peak -92 dBm avg -93 dBm
peak -92 dBm avg -93 dBm
In this example of a survey
on vertical polarization for 2
seconds on each 2 MHz
portion of the spectrum, the
largest amount of
interference was detected
at frequency 930 MHz (out-
of-band).
906 MHz Ch 1 peak -92 dBm avg -94 dBm
908 MHz
910 MHz
peak -92 dBm avg -94 dBm
peak -91 dBm avg -93 dBm
The asterisks, ****, indicate
the highest amounts of
interference detected and
correspond to the number
of yellow colored LEDs lit.
912 MHz Ch 2 peak -92 dBm avg -92 dBm
914 MHz
916 MHz
peak -91 dBm avg -92 dBm
peak -92 dBm avg -94 dBm
918 MHz Ch 3 peak -92 dBm avg -92 dBm
920 MHz
peak -92 dBm avg -93 dBm
922 MHz
peak -89 dBm avg -90 dBm
Note that the survey covers
spectrum outside the
924 MHz Ch 4 peak -89 dBm avg -89 dBm
926 MHz
928 MHz
930 MHz
932 MHz
934 MHz
936 MHz
938 MHz
940 MHz
942 MHz
944 MHz
946 MHz
948 MHz
950 MHz
peak -88 dBm avg -90 dBm
peak -57 dBm avg -70 dBm ***
peak -65 dBm avg -66 dBm ***
peak -69 dBm avg -70 dBm ***
peak -76 dBm avg -78 dBm *
peak -93 dBm avg -94 dBm
peak -85 dBm avg -90 dBm
peak -83 dBm avg -88 dBm
peak -83 dBm avg -89 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
peak -94 dBm avg -99 dBm
operational range of the
Once the site survey is completed, you are ready to install your radios. It is recommended that APs be installed first. The
reason for this is that the SU has a built-in RSSI tool that will help you properly aim the SU at the AP to achieve
maximum signal strength.
AP Search and SU Antenna Alignment
Once the AP is installed and aligned in the correct general direction, it is time to install the SU. The hardware installation
of the SU is identical to that of the AP, including considerations for line-of-sight, cable distances, cable type, weather
sealing, and grounding.
Once the SU is installed and aimed in the general direction of the AP, it is time to perform an RSSI (relative signal
strength indicator) test to determine the signal strength from the AP, and to precisely align the SU antenna for maximum
signal strength.
Although it is possible to rely upon the SU’s LEDs for alignment, more precise RSSI readings are available from the
command ssrssi.
Trango Broadband Wireless — User Manual M900S Rev C
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
In conjunction with the RSSI command, it is also useful to perform the apsearch command that will tell you which AP is
providing an adequate signal at the location of the SU.
AP Search
1. Ensure AP is in Opmode “On.”
2. Run the apsearch command to verify which AP is providing the strongest signal strength.
In this example, an AP is detected on channel 1,
#> apsearch
polarization horizontal. Further, the Base ID is 1234, and
the MAC address is 00 01 DE 15 5C D0.
Press [space] then [enter] to stop
1 906 Hz 1234 DE 15 5C D0 [H: -32 dBm] [V: -50 dBm] [E: -78 dBm]
2 912 Hz ---- FF FF FF FF [H: -80 dBm] [V: -86 dBm] [E: -99 dBm]
3 918 Hz ---- FF FF FF FF [H: -85 dBm] [V: -86 dBm] [E: -99 dBm]
4 924 Hz ---- FF FF FF FF [H: -82 dBm] [V: -81 dBm] [E: -99 dBm]
RSSI Command for Antenna Alignment
Step 1 Telnet into the SU (while in Opmode “OFF”). Use the freq and antenna command to note the radios current
settings.
Step 2 Run the rssi command. The telnet session screen will begin a continuous readout of the received signal strength.
As you read the RSSI reading, move the antenna in the horizontal and vertical planes until the maximum RSSI reading is
achieved. To allow for plenty of fade margin, we recommend a continuous RSSI reading of -78 dBm or better. An RSSI
of –88 dBm will allow you to establish a wireless link, but there may not be sufficient fade margin for reliable and
continuous operation.
Example 1 has the wrong freq and antenna settings:
#> rssi
[ 1] peak -80 dBm avg -93 dBm
[ 2] peak -80 dBm avg -97 dBm
[ 3] peak -99 dBm avg -99 dBm
Example 2 has the correct freq and antenna settings:
#> rssi
[ 1] peak -33 dBm avg -74 dBm **
[ 2] peak -33 dBm avg -68 dBm ***
[ 3] peak -33 dBm avg -64 dBm ****
Step 3 If it is not possible to receive an adequate RSSI reading, it may be necessary to reorient the AP (up/down,
left/right), to increase the output power of the AP, or to move the SU to a location with better line-of-sight conditions to
the AP. Alternatively consider using external antennas on either the AP or SU or both.
Once you are satisfied with the RSSI reading, tighten down the SU in the optimum position. To stop the RSSI continuous
readout, hit SPACE ENTER.
SU Alignment Using LEDs
The LED RSSI indicators on the bottom of the radio provide a handy alignment tool. If all four LEDs are lit, the unit is
receiving –60 dBm or stronger. If no LEDs are lit, there is not sufficient signal strength to establish a wireless link.
Lit LEDs Signal Strength
0 LED
1 LED
2 LED
-80 dBm
-75 dBm
-70 dBm
Trango Broadband Wireless — User Manual M900S Rev C
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
3 LED
4 LED
-65 dBm
-60 dBm
Collocation and Channel Planning
With proper channel planning and adherence to installation guidelines, multiple M900S APs may co-exist and operate
interference-free on the same tower or building. The main consideration when collocating APs is to ensure at least 10 ft.
of vertical separation. See the diagram below for collocation spacing, and a suggested channel plan.
M900S
COLOCATION SPACING
CH 2
10 ft
CH 4
60°
10 ft
CH 3
60°
CH 1
CH 2
60°
CH 1
CH 4
60°
10 ft
CH 3
ADJUSTMENTS IN AZIMUTH
WILL NOT HAVE A GREAT EFFECT
ON COLOCATION INTERFERENCE
30 ft
above
trees/structures
Mounting Mast
Link Management Commands
Once the radios are properly aligned for maximum RSSI, ensure the SU’s default Opmode is “ON” and that all
configuration parameters are correct.
Reboot the SU. Once the SU enters Opmode “ON,” the authentication process will begin, and the two radios will begin to
associate. From the AP side there are several basic diagnostics commands, such as su ping, su status, and su testrflink,
to ensure that a reliable RF link has been established. It may take one minute or more for the association process to
complete. This process may take longer if there are many SUs in the sector.
Trango Broadband Wireless — User Manual M900S Rev C
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
In establishing and diagnosing the quality of the link between the AP and SU(s), there are a few commands that are
especially useful. All of these commands are performed at the AP. A summary of these commands follows:
su
Displays the status of all SUs in the AP’s SUDB. SUs in the SUDB will appear by SU ID, and are classified into one of
the following status categories: Associated, Associating, and OFF.
Example:
#> su
[Priority] 88
[0]
[1]
[2]
[3] 88
[4]
[5]
[Associating]
[Power Off]
Success.
ꢀ Note: In this, and the following, examples the SU ID is 88
su ping <su#>
AP will send 10 RF pings to the designated SU ID. The response from each ping will indicate latency (in micro-seconds)
and the strength (RSSI) of the signal received back from the SU for each of the 10 pings. Note this command will also
tell you the distance from the AP to the SU.
Example:
#> su ping 88
[#Begin]
[001]
Ping #0 -> -57 dB 374 us 0.0 mi
Ping #1 -> -57 dB 373 us 0.0 mi
Ping #2 -> -57 dB 373 us 0.0 mi
Ping #3 -> -56 dB 373 us 0.0 mi
Ping #4 -> -56 dB 373 us 0.0 mi
Ping #5 -> -56 dB 374 us 0.0 mi
Ping #6 -> -57 dB 373 us 0.0 mi
Ping #7 -> -57 dB 374 us 0.0 mi
Ping #8 -> -56 dB 374 us 0.0 mi
Ping #9 -> -56 dB 373 us 0.0 mi
[#End]
Avg = -56 dB
Success.
su <su #>
AP will poll the SU for SU’s current status and will provide information such as SU range from AP, signal strength
received at SU from AP, SU temperature, etc. .
Example:
> su 88
[ 88] pr [as] y [d] 0.0 [rssi at ap] -60 dBm [rssi at su] -33 dBm
Trango Broadband Wireless — User Manual M900S Rev C
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Deployment
[ip] 192.168.100.120 [subnet] 255.255.255.0 [gateway] 192.168.100.120
[mac] 00 01 DE 16 E3 7F
[hw ver] 0005 [fpga ver] 03121104 [fpga chksum] 75930BDC
[fw ver] 1p0a2 [fw chksum] F4658C90 [fw datecode] 04010603
[default channel and antenna] 3 h [active channel and antenna] 3 h
[tx power] 26 dBm
[ch#1] 906 [ch#2] 912 [ch#3] 918 [ch#4] 924
[remarks]
[RF Tx Retry at AP] 0 [RF Tx Retry Maxed Out at AP] 0
[RF Tx Retry at SU] 0 [RF Tx Retry Maxed Out at SU] 0
Success.
su linktest <su#>
This command checks the integrity of the wireless link from the standpoint of performance (throughput) and over-the-air
packet loss. The AP will send 100 (1600 byte) packets to the SU, and the SU will return the packets it receives to the AP.
A perfect link (without dropped packets) will yield average throughput of 3,000 kbps. If heavy packet loss occurs, it may
be caused by interference or multi-path.
Example:
#> su linktest 88
[suid] 88 [pkt len] 1600 bytes [# of pkts per cycle] 100 [cycle] 10
0 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
1 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
2 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
3 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
4 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
5 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
6 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
7 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
8 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
9 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 866 ms 2956 kbps
[AP Total nTx]
[AP Total nRx]
1000 pkts
1000 pkts
[AP Total nRxErr] 0 pkts
[SU Total nTx]
[SU Total nRx]
1000 pkts
1000 pkts
[SU Total nRxErr] 0 pkts
[AP to SU Error Rate] 0.00 %
[SU to AP Error Rate] 0.00 %
[Avg of Throughput]
#> Success.
2956 kbps
su testrflink <su#>
This command also checks the integrity of the wireless link from the standpoint of over-the-air packet loss. Relative to the
linktest command, however this test does not provide as much detail. In this test the AP will send 20 large (1512 byte)
packets to the SU, and the SU will in turn send the same 20 packets back to the AP. The expected result of an error free
link is 20..20..20, indicating (in the following sequence) 20 packets sent from the AP, 20 packets received back at the AP,
and 20 packets received at the SU. Any results other than 20..20..20 indicate a performance problem, and are most likely
due to interference or an inadequate signal to noise ratio. For thorough results, it is recommended that you run the
command repeatedly for at least 1 minute or more to determine if packets are passing without error consistently over time.
Trango Broadband Wireless — User Manual M900S Rev C
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Management
The “r” is used in this command to repeat the RF link test repeatedly until the user terminates the test by hitting SPACE
ENTER.
Example:
#> su testrflink 88 r
Press [space] then [enter] to stop
[len] 1512
[suid] 88
[ 0] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[ 1] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[ 2] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[ 3] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[ 4] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
[ 5] ...........[AP Tx] 20 [AP Rx] 20 [SU Rx] 20
Success.
As another example, a result of 20..10..18 would indicate 20 packets sent from the AP, 18 packets received at the SU, and
10 packets received back at the AP. You might expect this type of results from Fresnel zone infringements, interference,
or multi-pathing.
ARQ with Selected Repeat and Multirate Feature
The M900S features ARQ or “Automatic Request for Re-transmission,” which provides the ability to correct for missing
or corrupted packets of data by asking the sender to re-transmit the data.
Both the AP and SU units implement a form of ARQ known as “ARQ with Selected Repeat.”
The units makes a first attempt at transmitting a data frame using the 3.250 Mbps rate. Then, if a re-try is required, the
2nd attempt will also be at 3.250 Mbps. The 3rd and 4th attempts will be at a rate of 1.625 Mbps. After the 4th attempt
there will be no more re-tries and a counter describing “maximum retries reached” will be incremented.
•
•
•
A minimum of 100ms is placed between re-transmission requests.
The units buffer up to 600 frames, or 4 seconds worth, of RF TX Data frames to support the ARQ algorithm.
The AP unit maintains counters concerning the ARQ algorithm on a per SU basis. The counters include the
following data:
Total Transmitted Frames
Total Retransmission Attempts
Total “Maximum Attempts Reached”
The SU unit maintains counters concerning its use of the ARQ algorithm. The counters include the same data as in the
AP.
Trango Broadband Wireless — User Manual M900S Rev C
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Management
Section 8 Management
Section Topics:
•
•
•
Radio Management Access using TCP/IP
SU Management from the AP’s command set
SNMP
Radio Management Access Via TCP/IP
The IP Address of an M900S radio is for management purposes only. The IP address is not used for purposes of routing
or passing traffic. Users should take care to set appropriate IP schemes for all management activities including upgrading
the radio’s firmware. It is not uncommon for users to assign public IP addresses to the radios so that they can be accessed
from anywhere via the Internet. In order to gain TCP/IP access to SU (from either side of the wireless network), ensure
that SU Switches 2 and 6 are turned on. In order to gain TCP/IP access to the AP from the SU side of the wireless
network, ensure that AP Switch 7 is turned on.
SU Management from AP
The AP provides functionality and several commands that permit the management of associated SUs. In fact, most
system management functions are performed by issuing commands from the AP. Presented below are a few examples of
these commands:
su ping <suid>
su status <suid>
su ipconfig <suid> <new IP> <new subnet> <new gateway>
su password <suid | all> <rw | ro> <new password> <new password>
su reboot <all|suid>
su testrflink <all|suid> [<r>]
su sw <suid> <sw #> <on|off>
Note: SU commands issued from the AP will automatically update the SU’s flash memory. No save ss command is
necessary.
As an example, you can remotely change the password for a single SU or all SUs in a sector:
su password <suid | all> <rw | ro> <new password> <new password>
Example:
#>su password all rw hello hello
to remotely change the read write password on all SUs to “hello”
As another example, to change an SU’s IP, subnet, and gateway: su ipconfig <suid> <new ip> <new subnet> <new
gateway>
Type the following:
#>su ipconfig 7 192.168.10.10 255.255.255.0 192.168.10.1
In this example SU #7’s IP address was changed to 192.168.10.10, the subnet mask to 255.255.255.0, and the gateway to
192.168.10.1.
A complete description of these commands and many others can be found in Appendix A – Command Set Reference.
Trango Broadband Wireless — User Manual M900S Rev C
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Management
Loading Multiple SUs into the SUDB using DLOAD Command
To load a full database of SU entries into the AP’s SUDB, you need to create a subscriber database in ASCII text file
format. As shown below, each row represents all information for one SU. Each column is an information field, which
includes: SU ID, SU to SU group, service level, CIR, MIR, and MAC address.
005 re a B 3000 3000 3000 3000 0000 00 01 de 16 e3 60
007 re a B 3000 3000 3000 3000 0000 00 01 de 16 e3 7c
009 re a B 3000 3000 3000 3000 0000 00 01 de 16 e3 7b
000
--- End of file indicator
--- -- - - ---- ---- ---- ---- ---- -----------------
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
------------- MAC Address
----------------------- Reserved (should be 0000)
---------------------------- MIR Uplink
--------------------------------- MIR Downlink
-------------------------------------- CIR Uplink
| | | | |
| | | | |
| | | |
| | | |
| | | |
------------------------------------------ CIR Downlink
| | | --------------------------------------------- SU2SU Group ID
| | |
| | |
| | ------------------------------------------------ Rate (currently not supported,
| |
| |
value should be a)
| --------------------------------------------------- pr Priority User
|
|
|
re Regular User
------------------------------------------------------ SU ID (1..127)
1. Telnet into the AP and run the command tftpd on to enable TFTP process.
2. Tftp the file to the AP from your DOS prompt example: tftp <IP of AP> put mySUs.txt.
3. From the AP’s telnet session, run the command sudb dload to load and activate the SUDB.
4. Run the command sudb view to verify the SUDB entries.
Run command save sudb to write the SUDB to non-volatile memory.
SNMP
The M900S supports Simple Network Management Protocol (SNMP) for network management. Network management
consists of the following 4 categories: configuration, accounting, alarm, and monitoring and control. These capabilities
allow the network operator to provide superior services through higher network availability and integrated accounting
systems. For more information on SNMP and its uses, you can visit http://www.faqs.org/faqs/snmp-faq/.
Trango Broadband Wireless — User Manual M900S Rev C
Page 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Management
The Trango SNMP solution supports MIB-II (system only) and the Trango proprietary Management Information Base
(MIB). The SNMP agent resides on the AP ONLY. The AP gathers health, status, and performance statistics from all
SUs locally, then responds back to the SNMP manager upon request.
Users interested in using the SNMP functionality should review the entire M900S MIB for a complete understanding of
its features. The M900S MIB is available for download at:
The following is an overview of a few of the more commonly used SNMP objects in the M900S system.
Objects for Monitoring and Control
SU Bandwidth Monitoring
•
•
•
•
suEthRXAvgThroughputLog – Average payload data throughput (in Kbits/sec) received on the Ethernet port
over the period specified by suStatisticsSamplePeriod (1 ~ 60 minutes).
suEthTXAvgThroughputLog - Average payload data throughput (in Kbits/sec) transmitted from the Ethernet
port over the period specified by suStatisticsSamplePeriod (1 ~ 60 minutes).
suRFRXAvgThroughputLog - Average payload data throughput (in Kbits/sec) received over the RF link over
the period specified by suStatisticsSamplePeriod (1 ~ 60 minutes).
suRFTXAvgThroughputLog - Average payload data throughput (in Kbits/sec) transmitted over the RF link
over the period specified by suStatisticsSamplePeriod (1 ~ 60 minutes).
•
•
suRFInOctets – Number of octets of payload transmitted from the AP’s RF port.
suRFOutOctets – Number of octets of payload received on the AP’s RF port.
AP Bandwidth Monitoring
•
•
•
•
aptrafficEthRXAvgThroughputLog – Average payload data throughput (in Kbits/sec) received on the Ethernet
port over the period of 1 minute.
aptrafficEthTXAvgThroughputLog – Average payload data throughput (in Kbits/sec) transmitted from the
Ethernet port over a period of 1 minute.
aptrafficRFRXAvgThroughputLog – Average payload data throughput (in Kbits/sec) received over the RF
link for a period of 1 minute.
aptrafficRFTXAvgThroughputLog – Average payload data throughput (in Kbits/sec) transmitted over the RF
link for the period of 1 minute.
•
•
•
•
aptrafficEthInOctets – Number of octets of payload received on the Ethernet port.
aptrafficEthOutOctets – Number of octets of payload transmitted from the Ethernet port.
aptrafficRFInOctets – Number of octets of payload received on the RF port.
aptrafficRFOutOctets – Number of octets of payload transmitted from the RF port.
Link Status Monitoring –Various traps are defined as follows:
•
•
•
•
•
•
Cold start – when SNMP agent starts running
Link Up – when the AP enters Opmode “ON”
Link Down – when the AP reboots
SU Link Up – when SU associates to the AP
SU Link Down – when SU disassociates from the AP
“AP” Opmode Failure – when AP fails to enter Opmode “ON”
AP and SU Control – SNMP also provides several control capabilities. The majority of the features available on the CLI
are also available via SNMP. Here are a few of these features:
•
•
•
•
Add/delete subscriber
Change channel
Set power
Set radio sensitivity
Review the Trango M900S MIB for the complete listing of MIB Objects.
Trango Broadband Wireless — User Manual M900S Rev C
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Management
SNMP Setup
Trango Broadband provides only the MIB portion of the SNMP Management system. The radios act as individual agents,
and it is up the user to provide an SNMP Manager software from a third party vendor. Below is an example of the setup
process for SNMPc from Castle Rock™.
1. Unzip trangopkg.zip file to a local temporary directory.
2. Go to your local temporary directory, you will see 4 files shown below.
a. trango_m900sap_1p0.mib – M900S AP MIB file
b. trango.ico – M900S AP icon
c. autoico.txt – instruction file (Selects Trango icon automatically during initial set-up.)
d. Readme.pdf – Configuration Guide
3. Copy trango_m900sap_1p0.mib file to C:\Program Files\SNMPc Network Manager\mibfiles
4. Copy autoico.txt file to C:\Program Files\SNMPc Network Manager\mibfiles
5. Copy trango.ico file to C:\Program Files\SNMPc Network Manager\bitmaps
6. The MIB needs to be compiled into the SNMPc database
By default, the Read Community is set to “public”, and Write Community is set to “private,” in the AP. The Trap
Community is “SNMP_trap.” The manager needs to have the same settings in order to communicate with the AP
successfully.
To send traps from the AP, set the following:
•
•
•
trap destination IP (Trango MIB object trapconfig–trapconfigInfo)
trap community string (Trango MIB object trapconfig–aptrpTable-AptrpEntry)
enable each trap (Trango MIB object traponfig–aptrpTable-AptrpEntry)
For all the set operations, set object SaveAndActivate at apsystem-apsystemInfo to write the information to FLASH.
Trango Broadband Wireless — User Manual M900S Rev C
Page 42
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Command Set Reference
(ro = read only access, rw = read write access)
Command
?
Radio Description
AP/SU Display complete list of commands and syntax
Access
ro/rw
? <command>
antenna
AP/SU Display specific command syntax
AP/SU Display current antenna setting
(h=horizontal, v=vertical, e=external )
AP/SU Select antenna mode
ro/rw
ro/rw
antenna <e | h | v>
rw
(h=horizontal, v=vertical, e=external) Note: Only use ‘e’ on
M900S-SU-EXT
aprssi <ch#> <antenna, h | v | e>
apsearch
AP/SU Scan two strongest APs
(Opmode “OFF” only)
AP/SU Scan all channels to look for APs
(Opmode “OFF” only)
ro/rw
ro/rw
arq
arq <on|off>
AP/SU Display current ARQ settings
AP/SU Enable/disable ARQ
ro/rw
rw
bye
eth link
AP/SU Same as “logout”
ro/rw
ro/rw
rw
ro/rw
ro/rw
rw
AP/SU Display current Ethernet setting
AP/SU Change Ethernet duplex setting
AP/SU Same as “logout”
AP/SU Display current channel
AP/SU Change current channel
AP/SU Display channel table
eth link <100fdx|100hdx|10fdx|10hdx|aneg>
exit
freq
freq <ch#>
freq channeltable
freq writechannel [<ch #> <freq>]…
ro/rw
rw
AP/SU Modify center frequency of channel.
<ch #> = 1..4
<freq> = 906..924
Note: This command automatically writes to flash memory.
AP/SU Display complete list of commands and syntax
AP/SU Display specific command syntax
AP/SU Assign radio’s IP, subnet mask, and gateway IP
help
ro/rw
ro/rw
rw
help <command>
ipconfig [<new ip> <new subnet mask> <new
gateway>]
linktest <txrx|rxtx> [<pkt len, bytes> [<# of
pkts> [<# of cycle>]]]
AP/SU Loopback test to check quality of the wireless link. Variable
parameters include:
ro/rw
pktlen = 64..1760,
# 0 pkts = 1..500
# of cycles = 1..100000
logout
maclist
maclist reset
mirth
mirth <0..3, Mbps>
AP/SU Log out of radio
AP/SU Display current MAC table (MAC addresses of attached devices)
AP/SU Display or reset current MAC table
ro/rw
ro/rw
ro/rw
ro/rw
rw
AP
AP
Display MIR (Maximum Information Rate) Threshold
Assign MIR Threshold
default = 3 Mbps
mirth 0 = Always On
mirth 3 = Disable MIR Threshold
opmode
opmode on [<y>]
AP/SU Display current Opmode
AP/SU Set Opmode to be “ON” and use “y” if Opmode is not as same as
default Opmode
ro/rw
ro/rw
password <rw|ro> <new pwd> <new pwd>
ping <ip address>
AP/SU Specify new password (max 15 octs)
rw=read/write password, ro=read only password
AP/SU Ping local Ethernet device
rw
ro/rw
Note: This command only works for local Ethernet devices, not SU
or any device behind SU.
power
AP/SU Display current TX power level
default = max. power value
AP/SU Specify TX power for both band
Note: SU’s power will be adjusted by AP during association process
ro/rw
rw
power set <min|max|<dBm>
Trango Broadband Wireless — User Manual M900S Rev. C
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
Radio Description
Access
(power leveling)
pppoeonly
pppoeonly <on | off>
SU
SU
Display current PPPoE filter setting
Change PPPoE filter setting
ro/rw
rw
With PPPoE filter set to ON, only PPPoE packets will pass Default:
off – Pass All Packets
reboot
remarks
remarks <str,31 octs>
reset
rfrxth
AP/SU Reboot unit
AP/SU Display remarks
AP/SU Overwrite remarks
AP/SU Reset radio’s system settings back to factory defaults, then reboot
AP/SU Display current RF RX Threshold
AP/SU Change current RF RX Threshold
default = -98 dBm
ro/rw
ro/rw
rw
rw
ro/rw
rw
rfrxth <-98..-55>
rssi
AP/SU Display current RX RSSI
ro/rw
rw
Opmode “OFF” only on AP
save <mainimage | fpgaimage> <current
chscksum> <new checksum>
AP/SU Save new firmware. This command gets new firmware image from
TFTP buffer, verifies checksum and writes to flash memory at main
or FPGA image section.
save sudb
save <systemsetting | ss>
set apid <ap-id>
AP
AP/SU Save current configuration into flash memory
AP Set AP ID, <ap-id> = 1..255
AP/SU Set base station id Base ID = XXXX where X = any alphanumeric
character except “/”
Save SUDB into flash memory
rw
rw
rw
rw
set baseid <base-id, 4 oct>
set defaultopmode <on | off>
set httpport [<port #>]
AP/SU Set default Opmode to “ON” or “OFF”
Factory set default Opmode is “OFF”
AP/SU Set or display HTTPD port number
port # = 1..65534
rw
rw
default port = 80
set snmpcomm <read | write | trap id# |trap all>
set telnetport [<port #>]
AP/SU Set SNMP read or write or trap community string
AP/SU Specify telnet port, <port #> = 1..65534
rw
rw
Default port = 23
snmpsample <min, 1..60>
su password <suid | all> <rw | ro> <new
password> <new password>
su <all | suid>
AP/SU Set SNMP sample period
rw
rw
AP
Change read/write or read-only password of all or a specific
subscriber
AP
AP
Display all or specific SU information in SUBD
Command issued from the AP to gather information about specific
SUs.
ro/rw
ro/rw
su info <suid>
1. Distance
2. RSSI at AP
3. RSSI at SU
4. IP address
5. Subnet address
6. Gateway address
7. Device ID
8. Hardware version
9. FPGA version
10. FPGA checksum
11. Firmware version
12. Firmware checksum
13. Firmware datecode
14. Broadcast/multicast packet filter on/off
15. Auto scan AP on/off
16. TCP/IP for AP on/off
17. HTTPD on/off
18. TCP/IP service for Ethernet port on/off
19. Default channel and antenna
20. Active channel and antenna
Trango Broadband Wireless — User Manual M900S Rev. C
Page 44
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
Radio Description
Access
21. TX power
22. Remarks
23. RF TX retry at AP, RF TX retry maxed out at AP
RF TX retry at SU, RF TX retry maxed out at SU
Change IP, subnet, gateway for specified SU
AP
rw
su ipconfig <suid> <new IP> <new
subnet> <new gateway>
su linktest <suid>
su ping <suid>
su reboot <all | suid>
su sw <suid> <sw #> <on | off>
sudb add <suid> <pr|re> <mac>
sudb cirmir <<suid>|all> <cir dn> <cir up>
<mir dn> <mir up>
AP
AP
AP
AP
AP
AP
Perform linktest for specified SU
Request SU’s ranging and RSSI information
Reboot a specific SU or all SUs
Change switch settings on specified SU
Add new SU to SUDB
ro/rw
ro/rw
rw
rw
rw
Change SU’s CIR/MIR settings
rw
sudb defaultcirmir
AP
AP
Display default CIR and MIR in SUDB
Change default CIR and MIR
ro/rw
rw
sudb defaultcirmir <cir_dn, 0..3000> <cir_up,
0..3000> <mir_dn, 0..3000> <mir_up, 0..3000>
sudb defaultcirmir <default cir dn> <default cir
up> <default mir dn> <default mir up>
sudb delete <suid | all>
AP
Set MIR/CIR values to default values
rw
AP
AP
Delete SU in SUDB
rw
rw
sudb dload
Download SUDB file from TFTP buffer and write to flash memory.
This command is used to load a text file that contains the SUDB into
the AP. This command can be useful if there are large numbers of
SUs in the sector.
sudb gid <suid | all> <0..15>
sudb view
survey <search time, sec> <antenna, h | v | e>
AP
AP
Change SU’s gid
Display all SUDB
rw
ro/rw
ro/rw
AP/SU Spectrum analysis of the entire band (and near band)
<search time> = 1..10 sec per channel
Opmode “OFF” only
Sw
AP/SU Display current sw setting
AP/SU set sw #0 – enable or disable packet filter for broadcast/ multicast
ro/rw
rw
sw 0 [<on | off>]
packets
on = filtering
default = on
sw 1 [<on | off>]
sw 2 [<on | off>]
SU
Enable or disable SU’s autoscan AP feature
If on, SU will automatically scan each channel and antenna port
searching for AP.
rw
rw
default=on
Note: Recommended setting for M900S-SU-EXT is off.
Enable or disable SU’s TCP/IP service for AP
Allows TCP/IP access to SU from AP side of network via wireless
link.
SU
AP
default = on
sw 3 [<on | off>]
sw 5 [<on | off>]
sw 6 [<on | off>]
Enable or disable SU to SU (peer to peer) service
default = off
rw
rw
rw
AP/SU Enable or disable HTTPD (browser interface)
default = on
SU
Enable or disable TCP/IP service for Ethernet port while SU is in
Opmode “ON”
default = on
sw 7 [<on | off>]
AP
Enable or disable TCP/IP service for SU. Allows TCP/IP access to
AP from SU side of network via wireless link.
default = on
rw
sysinfo
targetap
targetap all
AP/SU Display system configuration
ro/rw
ro/rw
rw
SU
SU
Display the SU current setting for target AP
SU will associate with any AP with the same Base ID
“all” is the default setting.
targetap only <mac1, hex> [<mac2, hex>]
targetrssi
SU
AP
SU will only associate with AP with specified MAC addresses.
Display SU Target RSSI in dBm. This setting is used in the SU
power leveling process.
rw
ro/rw
Trango Broadband Wireless — User Manual M900S Rev. C
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
targetrssi <dBm, -90..-50>
Radio Description
Access
rw
AP
Change target RSSI. Note: Target RSSI must be +5 dB more than
rfrxth (RFRX Threshold).
default = -60
tftpd
AP/SU display current TFTPD status (status is either on or off) This
command will also list any contents of the TFTP buffer.
AP/SU enable or disable TFTPD service. TFTPD must be on in order to
upload new firmware or new SUDB file.
ro/rw
rw
tftpd <on | off>
updateflash <systemsetting | ss>
AP/SU Save current settings. This command can be issued in several ways:
save ss, updateflash systemsetting, save systemsetting, and
updateflash ss
rw
updateflash <mainimage | fpgaimage>
<current chscksum> <new checksum>
AP/SU Retrieve uploaded firmware from TFTP buffer, verify checksum,
and write to flash memory at main or FPGA image section.
rw
updateflash sudb
ver
AP
Save SUDB into flash memory
rw
ro/rw
AP/SU Display firmware and date codes
1. Version number and date code
2. Firmware and FPGA version code
3. Firmware and FPGA image checksum
Trango Broadband Wireless — User Manual M900S Rev. C
Page 46
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Specifications
All specifications apply to the M900S-AP and M900S-SU, unless otherwise noted.
Radio Transmit Specifications
Storable Channels:
Agility:
4 memory locations
906 to 924 MHz in 1 MHz increments
Default channels:
Channel 1:
906 MHz
912 MHz
918 MHz
924 MHz
Channel 2:
Channel 3:
Channel 4:
Power Control Range:
Max: +26 dBm +/- 1
Min: -4 dBm +/- 2
Step: 1 dB
Pout:
+26 dBm max
Ant. Gain:
EIRP:
10 dBi
+36 dBm (4 Watt)
Freq. Stability:
Freq. Plan:
Modulated BW:
+/- 1.5 ppm PLL stabilized (+/-2.5ppm) over temperature
Single upconversion, 140 MHz IF
6.2 MHz (null to null, 40 dB down)
2nd Harmonic atten:
LO Supression:
Per CFR47 part 15.407
Per CFR47 part 15.407
Receiver Specifications
Storable Channels:
Agility:
4 memory locations
906 to 924 MHz in 1 MHz increments
Default channels:
Channel 1:
906 MHz
912 MHz
918 MHz
924 MHz
Channel 2:
Channel 3:
Channel 4:
Cascade Noise Figure:
Receiver Sensitivity:
3.250 MBPS Rate:
(1x10-6 BER)
< 7 dB
- 88 dBm typical-1600 byte packet
- 88 dBm typical-64 byte packet
1.625 MBPS Rate:
(1x10-6 BER)
- 91 dBm typical-1600 byte packet
- 91 dBm typical-64 byte packet
Image Rejection:
Frequency Plan:
LO stability:
> 90 dB
Single conversion, IF at 140 MHz
+/- 1.5 ppm PLL stabilized (+/-2.5ppm) over temperature
Ethernet I/O Specifications
Data Input/Output:
Connector:
Signaling Format:
Shielded RJ-45 Jack
IEEE802.3i (10baseT) and IEEE802.3u (100baseT) compliant
Trango Broadband Wireless — User Manual M900S Rev. C
Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto-Negotiation:
Bridging Frame Size:
Mngmt Frames:
Fully supports IEEE802.3-2002 Sect. 2 Clause 28
60 to 1600 bytes
60 to 1472 bytes (includes PING, TELNET, TFTP, HTTP)
Protection:
Bi-directional transient voltage protection diodes on all data lines
compliance with:
IEC61000-4-2 (ESD)
IEC61000-4-4 (EFT)
IEC61000-4-5 (Lightning)
Power Specifications
Input Voltage:
Input voltage range at unit is 10.5 VDC to 24 VDC max
Power is supplied via the unused pins of the RJ-45 Jack. Power is injected into the Ethernet cable using a junction box
(provided).
Current Cons.:
Protection:
400 mA in transmit and receive modes at max power using 24 V
standard adapter (8 W) and 10 ft cable from J-BOX to unit
28 volt Transient Voltage Suppression (TVS) on power input
Note: Voltages above 28 volts will cause damage to unit.
Mechanical and Environmental Specifications
General
Material:
Size:
Weight:
Mounting:
High Temp Polycarbonate radome and diecast metal enclosure
12.5” x 8” x 2.75” including mounting studs
4 lb
2 U-Brackets, all-thread rod, nuts and washers
Connectors/Indicators
RF Output:
Integral internal patch antenna per Part 15C, 15.203
External RP-SMA-f connector for external antenna
FCC Compliance:
The transceiver shall comply with the following:
FCC Part 15.407
FCC Part 15.207(a)
Operating Temp:
Storage:
-40º to 60º C
-40º to 85º C
Humidity:
NEMA Rating:
Shock:
100 % (When sealed properly.)
NEMA 4
Sustain 3 axis drop from 5 feet
Standard External Power Supply
24 Volt DC Power adapter and J-Box supplied with product.
Type:
Input:
Linear wallmount transformer
120 VAC
Output:
24 VDC +/- 1 V
Max current:
Connector:
1000 mA
5mm DC Barrel-type Plug
Standard External Power-over-Ethernet Junction Box
Type:
In-line female-to-female RJ-45 adapter for CAT-5 Ethernet cable
Connectors:
Eth. In:
Shielded RJ-45 Jack
DC Input:
5mm DC Barrel-type Jack
Trango Broadband Wireless — User Manual M900S Rev. C
Page 48
Download from Www.Somanuals.com. All Manuals Search And Download.
Eth. Out & DC Out: Shielded RJ-45 Jack
Pinout for Eth. Out: Power (+) on pins 7+8, ground (-) on pins 4+5 and eth. data on pins 1,2,3 & 6
Indicators:
Protection:
2 LEDs to indicate power and a connection to radio
Resettable fuse for DC input
Integrated Antenna (M900S-SU and M900S-SU-EXT)
Type:
Air-loaded Patch Antenna
Polarization:
Frequency:
Gain:
Az Beamwidth:
El Beamwidth:
Cross Pol:
Vertical or Horizontal Polarization, electrically selectable
902 to 928 MHz
+10 +/- 1 dBiL
60º (3 dB pts)
60º (3 dB pts)
>15 dB
Front/Back Ratio:
VSWR:
12 dB
< 2.0:1 over Bandwidth
Trango Broadband Wireless — User Manual M900S Rev. C
Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
|