Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
CHAPTER 1
INTRODUCTION
BEFORE INSTALLING YOUR MONITOR
READ THIS MANUAL COVER TO COVER.
PAY ATTENTION to all WARNING and CAUTIONS
DO NOT use computer components not recommend by the
manufacture
Do not attempt to service the monitor your self. If a problem
occurs, contact the manufacture's authorized service center
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled, color monitor
which uses a TFT LCD panel. The monitor conforms to EPA
Energy Star and VESA DPMS ( Display Power Management
Signaling) power management standards. Our monitor also
provide one option to accept the video input (like NTSC or PAL
signal), you can switch these input signal through OSD and the
video OSD setting please refer to the Chapter 4.
RGB MODE
This monitor is equipped with a microprocessor that
identifies your computer’ s video mode and allows user to adjust
the setting.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
FACTORY-PRESET MODES
Table 1 shows standard video mode setting that have been
pre-adjusted at the factory for accurate video display. These
setting are stored in the monitor's memory
Table 1. Factory-Preset Modes
Mode
NEC
VGA
Resolution
640x400
640x350
720x400
640x480
640x480
640x480
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1280x1024
1280x1024
H-Freq.(KHz) V-Freq(Hz)
24.83
31.47
31.47
31.47
37.86
37.5
56.4
70
70
60
72
75
SVGA
35.16
37.88
48.08
46.87
48.36
56.47
60
56.3
60.3
72.2
75
60
70
XGA
75
SXGA
63.98
80
60
75
Macintosh 640x480
832x624
35
49.7
48.78
60.241
66.7
74.55
60
1024x768
1024x768
74.927
2
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
SPECIFICATIONS
l
LCD-1700VRQ 17” LCD Monitor
Overall Dimension (HxWxD):
483 x 354 x 50.3 mm
Shipping Weight (G/W):
9 Kg
Effective Display area (H/V): 337.92 x 270.34 mm
Display colors:
Scan Frequencies:
Horizontal
16.7M colors
31.47K to 80KHz
60Hz to 75Hz
Vertical
Number of Pixels:
Pixel pitch:
Picture Tube:
Power:
1280x1024 pixels
0.264x0.264 mm
17" TFT LCD panel
Input
110-240VAC(auto-sensing)
Frequency: 48-62Hz
45Watts maximum (on)
15pin Mini D-sub (Standard)
6 x BNC connector
4 x camera input
Consumption
RGB Connector:
BNC connector
1 x playback
1 x recorder
RGB Signals:
Video
Analog RGB 0.7Vp-p/75W
Sync
Separate
Display Data Channel:
Compatibility
VESA DDC 1/2B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
Compatibility:
IBM and compatible, Apple
Macintosh, NEC
Environmental Limits:
Operating Temp
Storage Temp.
Operating Humidity
Storage Humidity
Agency Approval
EMI
32° to 104°F ( 0° to 40°C )
-4° to 140°F ( -20° to 60°C )
10 to 85% without condensation
10 to 95% without Condensation
FCC-A and CE
UL
Safety
4
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
Chapter 2
PRODUCT PACKAGE
Open the shipping carton and check the contents. If any
items are missing or damaged, contact your dealer
immediately.
The package should include the following items
l
l
8U 17” Color TFT LCD Monitor
Accessory Box:
1.
2.
3.
4.
VGA cable x 1
AC to DC adapter x 1
Power Cord x 1
User’s manual x 1
INSTALLING THE MONITOR
The monitor is equipped with an auto sensing power supply
for voltage ranges from 110~240VAC, 60/50Hz. Confirm the
line voltage designation on the rear panel of the monitor.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
FOLLOW THESE STEPS TO INSTALL THE
MONITOR
1. Before you connect the cables, make sure that the
monitor and the system unit power switches are OFF
2. Plug one end of the 15pin signal cable to the monitor and
the other end to the video signal connector at the rear of
the system. Tighten the two screws on the cable
connector on both ends, otherwise the screen will be
abnormal and LED light is yellow color, not the normal
green color.
3. Connect 4 cameras through BNC cable
4. Connect out BNC to recorder to record the screen
5. Connect the power to the monitor through the AC/DC
adapter
6
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
CONTROL FUNCTIONS
The OSD control functions of 17” Quad display LCD monitor are
located on the lower side. They are shown in the figure below
and described in the following paragraphs.
Menu
Ñ
D
-
+
AV/PC Menu ?/CH1 ?/CH2 -/CH3 +/CH4 =/AUTO
The first line is used for RGB OSD adjustment
The second line is used for security OSD adjustment
AV/PC: Switch the Screen between RGB and security
screen.
The RGB control key description:
1.
: Power Switch
2. /+ : Decrement/Increment or Volume control
3. Ñ/D : Cursor Up/Down or Brightness control
4. MENU: Activate the on screen display function
As the security control key definition, please see the chapter 4.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
Chapter 3
ADJUSTING THE PC MONITOR
The LCD monitor is designed to work with a range of
compatible video adapters on the market. Due to the possible
deviations between these video adapters, you may make
some adjustment to fit the monitor for adapter used.
ADJUSTMENT PROCEDURE
1. First, you must activate the OSD screen through pressing
the MENU key, the screen will show in the center of
screen as below:
Note: In the last paragraph, we will assume that you had
already done this procedure and only explain how to
change the setting.
2. Use the Ñ & D key to select the required adjustment item
up or down.
3. Use the & + key to change the control value for
optimum viewing.
4. Each change that you had made will be automatically
saved into memory, If the screen display garbage and you
don't know how to restore to correct setting, please move
arrow to "Load Value" item then pressing "-" key to load
factory default.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
We had two pages OSD screens; the screens are shown in
OSD screen 1 and 2, if you choose the source to video not
RGB, please see the next chapter.
OSD SCREEN1
1024x768
48KHz
60Hz
AUTO ADJUSTMENT
H-POSITION ------------
V-POSITION ------------
3
PIXEL CLOCK-----------
H-position
PHASE -------------------
Back light---------------
BL
COLOR Temperature
OSD H-position -------
OSD V-position -------
Next page -------------
FIRMWARE VERSION
SXGA 5F211-5140
9
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
OSD SCREEN2
1024x768
48KHz
60Hz
PREVIOUS PAGE ---
Brightness --------------
RED--------------
R
GREEN----------
BLUE-------------
G
B
Contrast ---------------
RED --------------
R
G
B
0
255
GREEN----------
BLUE ------------
128
720/640 selection----
OSD transparence -
OSD timeout------
Load Default ----------
FIREWARE VERSION
SXGA 5F211-5140
10
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
Adjustment Icon :
Auto-adjustment
Automatically adjust the pixel clock, H/V position
and fine tune the screen to get better visual quality.
H-position
Adjusts the screen's width. The range is from
0-255.
V-Position
Adjusts the screen's height. The Range is from
0-255.
Pixel Clock
Macro-adjust the screen size. The range is from
0-255
Phase
Fine tune the screen size to get stable image after
you finish the setting. The range is 0-31
BL Back light control
Adjust lamp current
Color Temperature
Adjust the color temperature
Contrast
Adjust RGB contrast values simultaneously, or you
can separately change each RGB value
720/640 Selection
Select the Text or Graphic mode display
OSD H-position
Move the OSD Horizontal Display location in the
Screen
11
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
OSD V-position
Change the OSD Vertical Display location in the
screen
Move to the next OSD screen
Move to the previous OSD screen
OSD transparency setting
To set the OSD display transparency mode.
Load default
OSD time out timer setting
VERTICAL & HORIZONTAL POSITION ADJUSTMENT
1. Use the Ñ & D key to move the 3to the
ICON, then
press & + to move the whole screen left or right to the
center position.
2. Use the Ñ & D key to move the 3to the
ICON, then
press & + to move the whole screen down or up to the
center position.
ADJUST THE VIEWING SCREEN SIZE
1. Use the Ñ & D key to move the 3to the
icon , then
icon ,then
press & + to get the larger viewing size.
2. Use the Ñ & D key to move the 3to the
press the & + key to get the stable setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
BRIGHTNESS ADJUSTMENT
1. Use the Ñ & D key to move the 3to the
icon, then
press &+ to get the best brightness optimization.
Note: We provide another easily method to do the brightness
adjustment. You don’ t need to activate the OSD screen, just
pressing the or + to change the brightness value.
CONTRAST ADJUSTMENT
Adjust the display contrast
1. Use the Ñ & D key to move the 3to the
icon, then
press & + to get the best brightness optimization. This
setting will influence all of RGB setting, if you want to
individually set each RGB setting, just move the 3to the
next Color-R, Color-G and Color-B icon to change.
OSD DISPLAY LOCATION ADJUSTMENT
Adjust the OSD display location
1. Use the Ñ & D key to move the 3to the
and
icon,
then press & + to change the OSD location as you
want horizontally or vertically .
13
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
HOW TO RESTORE THE PRE-DEFINE VALUE
Restore your previous define setting
1. Use the Ñ & D key to move the 3to the
icon, then
press “-” will automatically load the pre-define value for
each item.
2. Use this function only if you want to discard your new
setting.
UNDERSTAND THE DISPLAY RESOLUTION SETTING
To understand your display mode setting.
1. In the OSD screen, you will see the Horizontal frequency
(HF), Vertical frequency (VF), resolution and the monitor
Firmware version (ROM LEVEL). It is automatically
detected by the monitor user can not change this setting.
Note: we recommend to use auto adjustment item to fine
tune the monitor setting to get the better visual quality.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
CHAPTER 4
ADJUSTING THE SECURITY SCREEN
SETTING
The LCD monitor is designed to work with a range of compatible
video display on the market. Due to the possible deviations
between these video source, you may make some adjustment
to fit the monitor for video usage.
ADJUSTMENT PROCEDURE
1. First, you must activate the OSD screen through pressing
the MENU key, the screen will show in the center of screen
as below:
Note: In the last paragraph, we will assume that you had already
done this procedure and only explain how to change the setting.
2. Use the Ñ & D key to select the required adjustment item up
or down.
3. Use the
viewing.
& + key to change the control value for optimum
4. Any change that you make will be automatically saved into
memory, If the screen display is not optimal and you don't
know how to restore the correct setting, please move the
arrow to "Load Value" item then press "-" key to load factory
default settings.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
Security OSD menu setting
When your screen is in AV mode, pressing MENU key to enter into
OSD set up menu, you will see the following screen
SETUP MENU
SYSTEM
CAMERA
ALARM
PLAYBACK
VERSION
You can use ?or ? key to move the highlight bar to the desired item,
then press = to enter into the sub-menu to change setting.
The sub-menu of system is below
SYSTEM SETUP
FORMAT
DATE
TIME
YY-MM-DD
03-03-31
14:18:13
1
DWELL
You can change the date format , current timing and dwell timing.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
The sub-menu of camera is below
CAMERA SETUP
CAMERA
CAM1
10
22
55
99
BRIGHTENSS
CONTRAST
SHARPNESS
SAT U
SAT V
82
HUE
01
LOAD DEFAULT
You can set up each camera brightness, contrast, sharpness, sat U,
Sat V and hue setting to the better visual quality.
The sub-menu of alarm is below
ALARM SETUP
AUDIBLE
OFF/ON
It lets users to set up the audible on of off when camera signal is
missing.
The sub-menu of Playback is
CH1 CH2 CH3 CH4 PB OUT PWR PW
We also offer the hot key to let users easily operate the
LCD-1700VRQ machine.
Pressing ?/CH1 to let screen to display the channel 1 in full screen
Pressing ?/CH2 to let screen to display the channel 2 in full screen
Pressing ?/CH3 to let screen to display the channel 3 in full screen
Pressing +/CH4 to let screen to display the channel 4 in full screen
Pressing =/AUTO to let screen to display the screen as Channel, 1
Channel 2, Channel 3 , Channel 4, then Channel sequentially, the
duration is controlled by the DWELL setting in the system sub-menu.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
________________________17” Quad display LCD monitor
Pressing
to let screen to display 4 channel quad display.
Recording the screen will always set as quad display, When you
playback the screen, we offered one hot key to let user to see the full
channel # display. For example, if you want to see the playback
channel 1 in full screen, just pressing ?/CH1, the screen will show
the full screen of channel 1.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
17” Quad display LCD monitor ______________________
APPENDIX
SIGNAL CONNECTOR PIN-OUT
Power Connector
Pin 1
Ground
Pin 2
+12V output
RGB SIGNAL CONNECTOR
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Analog Red Input
Analog Green Input
Analog Blue Input
Ground
Digital Ground
Analog Red Ground
Analog Green Ground
Analog Blue Ground
NC
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Sync Ground
Ground
SDA ( DDC Data)
H. Sync
V. Sync
SCL ( DDC CLK )
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|