Toshiba VCR W 706 User Manual
Video Cassette Recorder  
W-7 0 6  
OWNER’S MANUAL  
REV  
FF  
PLAY  
STOP  
POWER  
EJECT  
PROG.TV  
PAUSE/STILL  
REC  
This publication is printed  
on recycled paper  
70971837  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT PRECAUTIONS  
Save Original Packing Materials  
The original shipping carton and packing materials will come in handy if you ever have to ship  
your VCR. For maximum protection, repack the set as it was originally packed at the factory.  
Avoid Volatile Liquid  
Do not use volatile liquids, such as an insect spray, near the unit.  
Do not leave rubber or plastic products touching the unit for a long time. They will mar the  
finish.  
Moisture Condensation  
Never operate this unit immediately after moving it from a cold location to a warm location.  
When the VCR is exposed to such a change in temperature, moisture may condense on the  
cylinder inside, one of its most crucial internal parts. To prevent the VCR from possible  
damage, do not use the unit for at least 2 hours when there is an extreme or sudden change  
in temperature.  
Compatibility  
This video cassette recorder (VCR) is compatible with any other VCR bearing the  
mark. HQ VHS equipment is also compatible with existing, non-HQ VHS equipment.  
Copyright  
It is permissible to record television programs, film, video tapes and other material only in the  
event that third party copyrights and other rights are not violated.  
®
As an ENERGY STAR Partner, TOSHIBA has determined that this product or  
®
product model meets the ENERGY STAR guidelines for energy efficiency.  
In the spaces provided below, record the Model and Serial No. located at the rear of your video  
cassette recorder.  
Model No.  
Serial No.  
Retain this information for future reference.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY  
INSTRUCTIONS  
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS  
GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT.  
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.  
This set has been designed and manufactured to assure personal safety. Improper use can  
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect  
you if you observe the following procedures for installation, use and servicing. This unit is  
fully transistorized and does not contain any parts that can be repaired by the user.  
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO  
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL  
ONLY.  
1. Read owner’s manual  
After unpacking this product, read the owner’s manual carefully, and follow all  
the operating and other instructions.  
2. Power Sources  
This product should be operated only from the type of power source indicated  
on the marking label. If you are not sure of the type of power supply to your  
home, consult your product dealer or local power company. For products  
intended to operate from battery power, or other sources, refer to the operating  
instructions.  
3. Grounding or Polarization  
This product may be equipped with a polarized alternating current line plug (a  
plug having one blade wider than the other). This plug will fit into the power  
outlet only one way. This is a safety feature. If you are unable to insert the plug  
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact  
your electrician to replace your obsolete outlet. Do not defeat the safety  
purpose of the polarized plug.  
4. Ventilation  
Slots and openings in the cabinet are provided for ventilation and to ensure  
reliable operation of the product and to protect it from overheating, and these  
openings must not be blocked or covered. The openings should never be  
blocked by placing the product on a bed, sofa, rug or other similar surface. This  
productshouldnotbeplacedinabuilt-ininstallationsuchasabookcaseorrack  
unless proper ventilation is provided or the manufacturer’s instructions have  
been adhered to.  
5. Heat  
Theproductshouldbesituatedawayfromheatsourcessuchasradiators, heat  
registers, stoves, or other products (including amplifiers) that produce heat.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Water and Moisture  
Do not use this product near water - for example, near a bath tub, wash bowl,  
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and  
the like.  
7. Cleaning  
Unplug this product from the wall outlet before cleaning. Do not use liquid  
cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
8. Power-Cord Protection  
Power-supply cords should be routed so that they are not likely to be walked  
on or pinched by items placed upon or against them, paying particular attention  
to cords at plugs, convenience receptacles, and the point where they exit from  
the product.  
9. Overloading  
Donotoverloadwalloutlets;extensioncords,orintegralconveniencereceptacles  
as this can result in a risk of fire or electric shock.  
10. Outdoor Antenna Grounding  
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system  
is grounded so as to provide some protection against voltage surges and built-up static charges. Article  
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper  
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge  
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding  
electrodes, and requirements for the grounding electrode.  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC – NATIONAL ELECTRICAL CODE  
S2898A  
11. Power Lines  
An outside antenna system should not be located in the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from touching such power lines or circuits as  
contact with them might be fatal.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY  
INSTRUCTIONS  
12. Lightning  
For added protection for this product during storm, or when it is left unattended  
and unused for long periods of time, unplug it from the wall outlet and  
disconnect the antenna or cable system. This will prevent damage to the  
product due to lightning and power-line surges.  
13. Object and Liquid Entry  
Never push objects of any kind into this product through openings as they may  
touch dangerous voltage points or short-out parts that could result in a fire or  
electric shock. Never spill liquid of any kind on the product.  
14. Attachments  
Do not use attachments not recommended by the product manufacturer as they may cause hazards.  
15. Accessories  
Do not place this product on an unstable cart, stand, tripod, bracket, or table.  
The product may fall, causing serious injury to a child or adult, and serious  
damage to the product. Use only with a cart, stand, tripod, bracket, or table  
recommended by the manufacturer, or sold with the product. Any mounting of  
the product should follow the manufacturer’s instructions, and should use a  
mounting accessory recommended by the manufacturer.  
S3125A  
A product and cart combination should be moved with care. Quick stops,  
excessive force, and uneven surfaces may cause the product and cart  
combination to overturn.  
16. Damage Requiring Service  
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the  
following conditions:  
a) When the power-supply cord or plug is damaged.  
b) If liquid has been spilled, or objects have fallen into the product.  
c) If the product has been exposed to rain or water.  
d) If the product does not operate normally by following the operating instructions. Adjust only those  
controls that are covered by the operating instructions as an improper adjustment of other controls  
may result in damage and will often require extensive work by a qualified technician to restore the  
product to its normal operation.  
e) If the product has been dropped or damaged in any way.  
f) When the product exhibits a distinct change in performance - this indicates a need for service.  
17. Servicing  
Do not attempt to service this product yourself as opening or removing covers  
may expose you to dangerous voltage or other hazards. Refer all servicing to  
qualified service personnel.  
18. Replacement Parts  
When replacement parts are required, be sure the service technician has used replacement parts  
specified by the manufacturer or have the same characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock, or other hazards.  
19. Safety Check  
Upon completion of any service or repairs to this product, ask the service  
technician to perform safety checks to determine that the product is in proper  
operating condition.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
INTRODUCTION  
Variable Speed Playback.................. 21  
Provides important notes and general  
explanation of the VCR, including names of the  
buttons, jacks, etc.  
• Picture Search  
• Still Picture  
• Slow-motion Picture  
• Frame Advance  
• Double Speed Playback  
• Shuttle Dial Operation  
SAFETY PRECAUTIONS .................... 2  
IMPORTANT PRECAUTIONS.............. 3  
IMPORTANT SAFETY  
INSTRUCTIONS ................................... 4  
Useful Functions in Tape  
Operation ........................................... 23  
Contents .............................................. 7  
Identification of Controls ................... 8  
• Counter Function  
• Tape Remaining Time  
• Index Search Function  
• Front Panel  
• Remote Control  
• VCR Display  
• Rear Panel  
RECORDING  
Explains recording functions.  
Recording a TV Program .................. 25  
PREPARATION  
• Watching a TV program while  
recording another  
• Recording off time setting  
Explains what you need to do before operating  
the VCR.  
How to Use the Remote Control ...... 10  
Connections ...................................... 11  
Auto Set Up ....................................... 14  
Timer Program Recording ............... 26  
VCR Plus+ C3 ® system Set-up ......... 29  
VCR Plus+ C3 ® system Recording .. 31  
Cable Box Set-up .............................. 33  
DSS® Satellite Receiver Set-up ........ 37  
MTS Broadcast Compatibility .......... 41  
Simulcast Recording ........................ 42  
Initial Settings Using On-screen  
Display ............................................... 15  
• Setting the Language  
• Optional settings on the SET UP  
screen  
• Setting the Clock  
Storing Channels on the VCR .......... 17  
Video Cassette Use .......................... 19  
ADDITIONAL INFORMATION  
Multi Brand Remote Control ............ 43  
Before Calling Service Personnel ... 45  
Specifications ................................... 47  
Accessories....................................... 47  
LIMITED WARRANTY ........................ 48  
PLAYBACK  
Explains variable functions concerning  
playback.  
Playback ............................................ 20  
• 19µ HEAD  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Identification of Controls  
See the page in  
for details.  
This manual shows the names of buttons in italics.  
Front Panel  
CHANNEL  
25  
EJECT  
19  
15  
PLAY  
STOP  
20  
20  
Cassette compartment  
19  
POWER  
REV  
(
FWD  
)
PLAY  
STOP  
POWER  
c
EJECT  
SHUTTLE  
CHANNEL  
22  
LINE IN  
2
PAUSE/STILL  
REC  
LINE IN 2  
VIDEO  
L-MONO-AUDIO-R  
VIDEO jack  
PAUSE/STILL  
Remote sensor  
21  
10  
LINE IN 2 AUDIO  
(L/MONO, R) jacks  
VCR display  
9
REC  
25  
Remote Control  
To operate this VCR.  
To operate your TV.  
VCR  
TV  
14  
VCR  
TV  
POWER  
POWER  
CH/TRK  
15  
25  
43  
1
4
2
5
8
0
3
6
9
Number buttons  
25  
25  
23  
CH/TRK  
100  
18  
I.SELECT  
REMAIN/COUNTER  
DISPLAY  
7
I.SELECT  
TV VOL  
TV/VCR  
43  
25  
TV VOL  
100  
REMAIN/  
COUNTER  
DISPLAY  
SP/SLP  
COUNT RESET  
TV/VCR  
TIMER  
23  
25  
25  
REC  
COUNT RESET  
23  
SP/SLP  
TIMER  
27  
PLAY/x2  
REC  
PLAY/x2 *  
20  
REW  
FF  
CURSOR  
STOP  
REW *  
20  
FF *  
20  
SLOW  
PAUSE/STILL  
SLOW 21  
PAUSE/STILL  
21  
PROG.  
ENTER  
CANCEL  
19µ/  
+
VCR Plus  
A.SELECT  
STOP *  
PROG.  
CH  
15  
20  
EJECT  
INDEX  
POWER  
ENTER  
19µ  
20  
VCR Plus+ 31  
15  
CABLE  
BOX  
EJECT  
19  
28  
POWER (CABLE BOX)  
35  
CANCEL  
CH (CABLE BOX)  
35  
A.SELECT  
41  
INDEX  
24  
* These buttons are used to control the  
cursor on the screen.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Display  
VCR indicator  
Timer recording indicator  
REMAIN indicator  
Cassette indicator  
OFF indicator  
POWER indicator  
AM PM  
REMAIN  
POWER  
L
Hi-Fi (L/R) indicators  
L: Left channel  
R:Right channel  
off: Normal track  
SLP  
OFF  
R
VCR  
TIMER  
REC  
DT  
CH  
H
M
S
Multifunctional indicator  
DT (Digital Auto Tracking) indicator  
Channel indicator  
REC (Recording)  
indicator  
Tape speed indicator  
(SP/SLP)  
Tape running direction/speed indicator  
Rear Panel  
LINE OUT VIDEO jack  
LINE IN 1 VIDEO jack  
RF IN (FROM ANT.) terminal  
To wall outlet  
LINE IN 1 AUDIO jacks (L, R)  
CH selector (3/4)  
RF OUT (TO TV) terminal  
LINE OUT AUDIO jacks (L, R)  
LINE IN 1 AUDIO (Rear), 2 (Front) jacks  
If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same  
sound is recorded on both L and R on the Hi-Fi track.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
How to Use the Remote Control  
This section explains how to get ready for remote control operation.  
Setting up the Remote Control  
Open the battery compartment lid on the  
rear panel.  
1
Install 2 batteries (“AAA” size) following  
the polarity diagrams.  
2
3
4
Close the battery compartment lid.  
Point the remote control at the VCR and press the buttons within the operating range.  
Distance: within about 7 m from the front of the remote sensor  
Angles:  
within about 30˚ in every direction  
Notes on batteries  
Caring for the remote control  
• The life of the batteries is about 1 year  
depending on the conditions of use.  
• If the remote control does not operate correctly,  
• Do not expose the remote sensor of the VCR  
to a strong light source such as direct sunlight  
or illumination (especially high-frequency  
lighting) when using the remote control.  
replace all batteries with new ones.  
• Be careful not to spill water on the remote  
control or to place it on anything wet, and avoid  
sharp impacts.  
• If the remote control is not to be used for a  
long period of time, remove the batteries to  
avoid possible damage from battery corrosion.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
Connections  
Before you use this VCR, it is necessary to connect it to your TV. Several ways of connecting are  
available depending on your use of TV or cable box. Select one which is applicable to your equipment.  
Antenna/VCR/TV Connection  
Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the  
VCR.  
1
Connect the RF OUT terminal to the TV.  
2
VHF/UHF combinaion  
antenna  
VHF antenna  
only  
UHF antenna  
only  
1
IN  
(FROM ANT.)  
VHF/UHF  
2
OUT  
(TO TV)  
VHF UHF  
Setting the VCR Output Channel  
When the VCR is connected in this way, the VCR sends the output  
signals to channel 3 or 4 on your TV. Set the output channel  
selector (CH selector) of the VCR to “3” or “4”, whichever is vacant  
in your area.  
Antenna splitter  
(not supplied)  
AUDIO/VIDEO Connections  
The AUDIO/VIDEO jacks are also available to connect your TV.  
When connected your TV using the  
AUDIO/VIDEO OUT jacks  
To watch video pictures, set the video input mode on  
your TV. For the video input mode, refer to the  
manual of your TV.  
LINE OUT VIDEO  
VIDEO IN  
LINE OUT AUDIO AUDIO IN  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections (continued)  
Cable Connection  
Choose one of the below according to your usage of the cable box.  
This set-up will enable you to:  
– record an unscrambled channel.  
– watch an unscrambled channel while recording  
it.  
– record an unscrambled channel while watching  
another (only when you connect a cable-  
compatible TV).  
Incoming cable  
You will need to:  
• select TV channel 3 or 4 to receive video  
signals. (See page 11.)  
• to record a channel while watching another,  
press TV/VCR on the remote control to turn off  
the “VCR” indicator in the VCR display and  
select a desired channel on the TV (only when  
you connect a cable-compatible TV).  
This set-up will enable you to:  
– record an unscrambled channel.  
– watch an unscrambled channel while recording  
it.  
– record an unscrambled channel while watching  
another (scrambled or unscrambled).  
Cable Box  
IN  
OUT  
You will need to:  
Incoming cable  
• set TV channel to the output channel of the  
cable box.  
• turn on the cable box and select cable channel  
3 or 4 according to the output channel of the  
VCR.  
• to record a channel while watching another,  
press TV/VCR on the remote control to turn off  
the “VCR” indicator in the VCR display and  
select a desired cable channel on the cable  
box.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This set-up will enable you to:  
– watch an unscrambled or scrambled channel  
while recording it.  
– record any channels through the cable box.  
Cable Box  
You will need to:  
• set TV channel 3 or 4 to receive video signals.  
(See page 11.)  
IN  
OUT  
• set VCR channel to the output channel of the  
cable box, and select a desired cable channel  
on the cable box.  
• while the VCR is turned off or the “VCR”  
indicator is not lit in the VCR display, set TV  
channel to the output channel of the cable box.  
A/B switch  
A
This set-up will enable you to:  
A
B
– watch an unscrambled or scrambled channel  
while recording it.  
B
Cable Box  
– record an unscrambled channel while watching  
another unscrambled channel (only when you  
connect a cable-compatible TV).  
• A/B switch “A”: record and watch an  
unscrambled channel which  
comes bypassing the cable box.  
• A/B switch “B”: record and watch a scrambled  
or unscrambled channel coming  
through the cable box.  
This set-up will enable you to:  
– watch or record a channel through the cable  
box via the LINE IN 1 (AUDIO/VIDEO) jacks.  
You will need to:  
• press I.SELECT so that the VCR display  
shows “L1”.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
Auto Set Up  
The Auto Set Up function automatically sets the tuner channels and clock when power is first connected  
to the VCR.  
Preparation  
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video  
connection (page 11).  
• Press I.SELECT so that the channel number will appear if “L1” or “L2” is displayed in the VCR display.  
• Press VCR to set the remote control operating the VCR.  
Auto Set Up  
Connect the antenna cable to the VCR (see page 11). Then connect the VCR’s power  
plug to an AC outlet.  
1
“Auto” flashes in the VCR display as the VCR automatically tunes in all active stations.  
When Auto Set Up is completed successfully, the current time will be displayed.  
VCR display  
VCR display  
PM  
Auto Set Up completed.  
Tuning in progress.  
• If the VCR fails to set the clock, “– : – –” will be displayed. Set the clock manually. (Refer  
to “Setting the clock” on page 16.)  
Notes  
• If you press the CANCEL button, the Auto Set Up is cancelled.  
• If Auto Set Up is not perform successfully, perform the clock and Tuner Channel procedures manually  
(page 16 to 18).  
• If, however, you want to add or delete channels, refer to “Adding or erasing channels” on page 18.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
Initial Settings Using On-screen Display  
Language selection must be set first when the VCR is first plugged in, or after it encounters a power  
failure. You can also easily make necessary settings using the on-screen displays.  
Preparation  
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video  
connection (page 11).  
• Press VCR to set the remote control operating the VCR.  
Setting the Language  
VCR  
POWER  
Press POWER to turn on the VCR.  
1
1
4
7
2
5
8
0
3
6
Press PROG..  
The following screen appears on the TV.  
2
3
4
9
SET UP  
PRESET  
PROGRAM  
100  
EnGL I SH  
FRAnÇA I S  
ESPAñOL  
REW  
FF  
PLAY/x2  
REW  
FF  
PROG  
nD:  
E
PLAY/x2,  
STOP  
STOP  
ENTER  
Select the language using PLAY/x2  
(CURSOR ) or STOP (CURSOR  
) , and press PROG..  
MEnU  
PROG.  
The screen turns to the MENU screen.  
SET UP  
PRESET  
PROGRAM  
PROG  
En  
D:  
ENTER  
Press PROG. to return to the normal TV screen.  
Optional settings on the SET UP screen  
Other optional settings can be made. Press ENTER while “SET UP” is selected on the  
MENU screen. The screen turns to the SET UP screen.  
Page 23  
SET UP  
n
GTH  
PRESET  
PROGRAM  
Page 41  
Page 42  
TAPE LE  
SAP SET  
120 160 180  
On  
OFF  
OFF  
S IMULCAST  
ANTEnn  
LA GUAGE  
DS FO  
O
n
A
AUTO  
MA U  
n
With “AUTO” set, a TV broadcast will appear via the TV tuner after  
playback.  
Move down here, and set to “AUTO” or “MANU”.  
If you made the Audio/Video connection (page 11), set to “MANU”.  
n
EnG FRA ESP  
X
I
n
O
n
OFF  
PROG  
nD:  
E
To change the language, move down here and set to the desired one.  
With “ON” set, you can see the station ID and program title displayed on  
TV.  
To exit, press PROG.  
(Continued)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Initial Settings Using On-Screen Display (continued)  
Setting the Clock  
Press ENTER to start the “AUTO” clock  
set feature.  
After a while, the VCR automatically updates  
the clock using the data broadcast by the  
local TV stations.  
8
Example: To set the clock to 2:30 p.m. on  
August 25 (summer time) 2000.  
Press PROG..  
The MENU screen appears on the TV.  
1
The following screen will appear on TV  
depending on the broadcast at your location.  
Select “PRESET” using FF or REW, and  
press ENTER.  
2
SET UP  
PRESET  
PROGRAM  
CL  
O
CK SET  
SUMMER T I  
T I  
M
E
SET UP  
PRESET  
PROGRAM  
M
E
ZOnE CH  
AUTO AUTO  
I
n
AUTOEASTERn AUTO  
2
T I  
M
E
DATE YEAR  
CL  
CH  
O
CK SET  
9
:
57A  
M
1 / 01 ’ 00 SA  
M
EMORY  
PROG  
En  
D:  
ENTER  
CABLE BOX / DSS  
GU I DE CH  
Select the options using FF or REW.  
Change the data using PLAY/x2 or  
STOP.  
1) Set “SUMMER TIME (Daylight-  
Saving Time)”.  
9
PROG  
E
n
D:  
ENTER  
Press ENTER to select “CLOCK SET”.  
3
4
SET UP  
PRESET  
PROGRAM  
CL  
IN, daylight-saving time begins on the first  
Sunday in April. Because the clock  
automatically changes from 2:00 AM to  
3:00 AM (forward one hour), remember  
that any part of a scheduled Timer  
Recording that falls between these two  
times will not be recorded.  
OUT, daylight-saving time ends on the last  
Sunday in October. The VCR clock  
automatically changes from 2:00 AM to  
1:00 AM (back one hour). Therefore, it can  
affect your recording length if one is set  
for this time.  
O
CK SET  
SUMMER T I  
T I DATE YEAR  
UT 12 : 00A  
M
E
M
E
MAnU  
O
M
1 / 01 ’ 00 SA  
PROG  
nD:  
E
Select “AUTO” or “MANU” using PLAY/  
x2 or STOP.  
AUTO: The VCR automatically sets or  
adjusts the clock.  
If you select “AUTO” mode, proceed to step 8.  
MANU: You can set the clock manually.  
If you select “MANU” mode, select “SUMMER  
TIME” using FF. Set to “IN” or “OUT” for the  
summer (daylight saving) time using PLAY/x2  
or STOP. (For “IN” and “OUT” selections, see  
the description in step 9.)  
2) Set “Time Zone”.  
If you select “AUTO” for your time zone,  
the VCR sets the clock using the first  
Coordinated Universal Time information it  
finds. If the time is not correct, select  
another time zone or use the “MANU”  
option.  
Move to the next using FF.  
(To move back, press REW.)  
5
6
3) Set “CH”.  
If you don't know the clock data channel,  
select “AUTO”. The VCR will scan  
automatically to tune the channel carrying  
the clock data.  
Vary the digits to set the hour.  
PLAY/x2: To increase.  
STOP:  
To decrease.  
If AUTO CLOCK SET is unsuccessful, set the  
time and date through the “MANU” clock set  
menu selection.  
Repeat steps 5 and 6 to set the minutes,  
month, day, and the year (by the last two  
digits).  
7
Press PROG..  
Now the clock starts.  
10  
11  
Proceed to step 10 to start the clock.  
Press PROG. to exit.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
Storing Channels on the VCR  
This section is required if you receive only normal TV or unscrambled cable channels, or use a cable box  
between your TV and the VCR.  
Incoming Antenna/Cable (CATV) Signals  
The VCR scans through all receivable TV and CATV channels and stores only the active  
ones in your area into the memory. Once the storing is finished, you can select a desired  
channel using CH/TRK.  
Preparation  
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video  
connection (page 11).  
• Press I.SELECT so that the channel number will appear if “L1” or “L2” is displayed in the VCR display.  
Incoming Antenna/Cable (CATV) Signals  
Press PROG. to display the MENU screen.  
1
1
4
7
2
5
8
0
3
6
Number  
buttons  
Select “PRESET” using FF or REW,  
and press ENTER.  
2
SET UP  
PRESET  
PROGRAM  
9
100  
100  
I.SELECT  
CL  
CH  
O
CK SET  
M
EMORY  
CABLE BOX / DSS  
GU I DE CH  
REW  
FF  
PLAY/x2  
REW  
FF  
PROG  
En  
D:  
ENTER  
PLAY/x2,  
STOP  
STOP  
Select “CH MEMORY” using PLAY/  
x2 or STOP, and press ENTER.  
3
ENTER  
SET UP  
PRESET  
CATV  
PROGRAM  
TV / CATV  
AUTO SCA  
ADD CH  
TV  
OFF  
n
O
n
1, 6  
––CH  
––CH  
ERASE CH  
PROG  
EnD:  
Set “TV/CATV“ to “TV” or “CATV” using FF or REW.  
TV: To store channels received via the antenna.  
CATV: To store channels received via the incoming cable.  
4
5
Select “AUTO SCAN” using PLAY/x2  
or STOP, and press FF to set to  
“ON”.  
SET UP  
PRESET  
PROGRAM  
TV  
AUTO SCA  
n
2CH  
On  
The VCR starts scanning and the  
channels are stored in the VCR in  
ascending order. When the scanning is  
finished, the screen automatically  
returns.  
PROG  
EnD:  
Press PROG. to exit.  
6
(Continued)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Storing Channels on the VCR (continued)  
3) Enter a channel number of 1 to 125 using  
Adding or erasing channels  
number buttons.  
For more than 100 number, first press 100.  
For CATV channels, refer to the chart below.  
(For other orders, check with your cable  
company.)  
Adding channels  
If a desired channel cannot be scanned  
automatically because of a weak signal, it can be  
added to the memory.  
Erasing channels  
You can erase a stored channel from the memory  
if it is unnecessary.  
4) Repeat steps 2) and 3) to add or erase  
channels as necessary.  
5) Press PROG. to exit.  
1) Follow steps 1 to 3 of “Incoming Antenna/CATV  
Signals”.  
Selecting stored channels  
2) Select “ADD CH” or “ERASE CH” using PLAY/X2  
Once the active channels have been stored, you  
can select the channels in two ways below.  
Number buttons  
To enter digits of the channel number.  
• For one-digit number, enter 0 before.  
• For more than 100 number, first press 100.  
• Each number button needs to be pressed  
within 2 seconds.  
or STOP.  
To add channels  
SET UP  
PRESET  
PROGRAM  
TV / CATV  
AUTO SCA  
ADD CH  
TV  
OFF  
CATV  
n
O
n
––On  
––On  
ERASE CH  
TO SET CH  
PUSH 0~9 KEYS  
PROG  
EnD:  
CH/TRK  
To shift up or down the stored channel numbers.  
To erase channels  
SET UP  
PRESET  
PROGRAM  
TV / CATV  
AUTO SCA  
ADD CH  
TV  
CATV  
n
OFF  
O
n
––On  
––On  
ERASE CH  
TO SET CH  
PUSH 0~9 KEYS  
PROG  
EnD:  
Channel reference chart  
1
–
1(A-8)  
2
2
2
3
3
3
4
4
4
5
5
6
6
7
7
7
8
8
8
9
9
9
Number on the VCR  
TV  
Corresponding channel number  
5(A-7) 6(A-6)  
CATV STD (HRC/IRC)  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30  
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30  
10 11 12 13  
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51  
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51  
R
S
T
U
V
W
AA BB CC DD EE FF GG HH II  
JJ KK LL MM NN OO  
…
…
…
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71  
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69  
PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71  
–
–
…
…
…
93 94 95 96 97 98 99 100 101 102 103  
121 122 123 124 125  
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 103  
121 122 123 124 125  
CATV signals  
• STD (standard) cable TV signals  
• HRC (Harmonic Related Carriers) cable TV signals  
• IRC (Incremental Related Carriers) cable TV signals  
IRC is also called ICC (Incremental Coherent Carriers)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
Video Cassette Use  
Video Cassette Use  
Loading a cassette  
Push the cassette into the cassette compartment with the window side facing up and the  
label side towards the front. The VCR is automatically turned on. The  
appear in the VCR display.  
indicator will  
Ejecting a cassette  
Press EJECT. The cassette is ejected from the cassette compartment.  
Warning  
Do not insert your hands or any foreign objects into the compartment. This may result  
in injury or damage. Take special care with children to avoid accidents.  
Precautions when using video cassettes  
Video cassettes have a safety tab to prevent accidental erasure. If the tab has already been removed,  
recording cannot be performed.  
To prevent accidental erasure  
To record again  
Remove this safety tab with a screwdriver.  
Cover the tab hole with adhesive tape.  
• Avoid exposing cassettes to direct sunlight. Keep them away from heaters.  
Avoid extreme humidity, vibrations or shock, strong magnetic fields (near a motor, transformer or  
magnet) and dusty place.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
Playback  
This section explains the basic playback operation.  
Preparation  
• Select the video channel (3 or 4) or video input mode on the TV.  
• Press VCR to set the remote control operating the VCR.  
Basic Playback  
VCR  
1
4
7
2
5
8
0
3
6
CH/TRK  
Load a recorded cassette.  
1
POWER  
9
Power is turned on.  
100  
If the cassette has no safety tab,  
playback starts automatically.  
PLAY/x2  
2
FF  
Press PLAY/x2 to start playback.  
2
3
POWER  
REW  
FF  
S
P
VCR  
DT  
STOP  
3
REW  
µ
19  
To stop playback, press STOP.  
Rewinding / Fast-forwarding  
Press REW or FF in the stop mode.  
Adjusting the tracking  
19µ HEAD  
When playback starts, the VCR  
automatically adjusts the tracking for clear  
pictures and sound (Digital Auto Tracking).  
You can view high quality pictures while  
playing back a tape recorded in the SLP tape  
speed.  
By pressing 19µ repeatedly, the 19µ HEAD  
mode is displayed on the TV screen as  
follows:  
The “DT” indicator blinks during the  
adjusting.  
If the VCR cannot locate the best possible  
tracking point, hold down one of CH/TRK to  
adjust the tracking manually.  
• To resume the digital auto tracking, hold  
down both CHANNEL on the VCR  
simultaneously for about 2 seconds.  
19U-HEAD AUTO: Usually set to “AUTO”. As  
the playback starts, the VCR automatically  
activates the 19µ head and reproduces high  
quality pictures.  
19U-HEAD OFF: Set to “OFF” if the  
pictures are marred by dots.  
Notes  
• During the adjusting, the playback picture and  
sound may be distorted.  
• The digital auto tracking is activated only in the  
playback mode.  
• To reset the manual tracking point to the center,  
press both CHANNEL on the VCR  
simultaneously for not longer than 1 second.  
• The noise on the screen may not be completely  
eliminated depending on the tape used,  
especially when the tape was recorded on  
another VCR.  
Note  
During playback with the 19µ head, momentary  
noises or shakes may be produced when you  
change the mode to the picture search or  
variable speed playback.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
Variable Speed Playback  
You can play back a tape at various tape speeds.  
Picture Search  
1
4
7
2
5
8
0
3
6
A tape runs at 5 times or 7 times the normal playback speed so  
that you can quickly locate a particular scene.  
9
100  
Press FF or REW during playback.  
The tape runs at 5 times the normal playback speed.  
1
PLAY/x2  
REW  
PLAY/x2  
To change the tape speed to 7 times the normal playback  
speed, press and hold FF or REW.  
2
REW  
FF  
FF  
STOP  
If you release it, the tape speed returns to 5 times.  
PAUSE/STILL  
Note  
SLOW  
If you press FF or REW during picture search, the mode changes to fast-  
forwarding or rewinding.  
To resume normal playback  
Press PLAY/x2.  
Still Picture  
Slow-motion Picture  
A picture freezes so that you can watch  
closer.  
The tape runs at 1/7th or 1/15th the normal  
playback speed.  
Press PAUSE/STILL during playback.  
The picture freezes.  
Press SLOW during playback.  
The tape runs at about 1/7th the normal  
playback speed.  
1
1
To resume normal playback  
Each time you press SLOW, the speed  
alternates between 1/7th and 1/15th.  
Press PAUSE/STILL.  
Notes  
To resume normal playback  
Press PLAY/x2.  
• The still mode is automatically cancelled after  
about 5 minutes and returns to normal playback.  
• The still picture may shake if a picture of a fast-  
moving object or scene is frozen. This is not a  
defect in the unit.  
Notes  
• The slow-motion picture mode is automatically  
cancelled after about 5 minutes and returns to  
normal playback.  
• The slow-motion picture may flicker up and down.  
This is not a defect in the unit.  
Adjusting Still Picture Stability  
If the still picture is distorted or flickers, hold  
down one of CH/TRK until the picture becomes  
stable.  
Adjusting the Tracking Manually  
If the slow-motion picture is noisy, hold down one  
Note  
of CH/TRK until the best picture is obtained.  
The distortion of the still picture may not be  
eliminated completely.  
Note  
The noise in the slow-motion picture may not be  
eliminated completely.  
Note  
When playing back a tape which is recorded in S-VHS format, distortion may occur during the variable speed  
playback.  
(Continued)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Variable Speed Playback (continued)  
Frame Advance  
Double Speed Playback  
A picture advances frame by frame.  
A tape runs at twice the normal speed.  
Press PLAY/x2 during still playback.  
Each time you press PLAY/x2, the picture  
advances one frame.  
Press PLAY/x2 during playback.  
The picture runs at twice the normal playback  
speed.  
1
1
If you press and hold PLAY/x2, the tape runs  
at 1/30th the normal playback speed.  
To resume normal playback  
Press PLAY/x2.  
To resume normal playback  
Press PAUSE/STILL.  
Shuttle Dial Operation  
You can also activate the picture search and slow playback at  
various speeds by turning the shuttle dial on the VCR.  
Turn the shuttle dial on the VCR.  
1
Initial mode of tape operation  
Stop  
o
r
Playback  
Still  
The playback speeds differ depending on the recording tape speed of  
the tape as follows.  
Picture search  
x5 x7  
x15 x21  
Reverse playback  
SP:  
SLP:  
-x1  
-x3  
Notes  
• The still picture mode will be released automatically after about 5 minutes  
and forward playback will start.  
• Fast-forwarding or rewinding started from the stop mode continues even if  
the shuttle dial is released. To stop, press STOP.  
• The reverse playback mode will be released automatically after about 25  
seconds and forward playback will start.  
• Noise bar may appear in reverse playback.  
Note  
If you playback a tape recorded in the SLP tape speed or a tape recorded on another VCR in various speed  
mode, the picture may be noisy or monochrome.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYBACK  
Useful Functions in Tape Operation  
These functions will help your playback.  
S-VHS Quasi Playback (SQPB)  
• This VCR can also play back a tape which is recorded in S-VHS format.  
But the playback picture does not have the same quality and resolution as  
the original S-VHS playback picture.  
• This VCR cannot record in S-VHS format.  
* SQPB is an abbreviation for S-VHS Quasi Playback.  
Counter Function  
1
4
7
2
5
8
0
3
6
You can view the clock, linear time counter or tape remaining  
time in the VCR display or on the TV screen.  
REMAIN/  
COUNTER  
9
100  
COUNT RESET  
DISPLAY  
PLAY/x2  
Each time you press REMAIN/COUNTER, the VCR display  
changes in sequence as follows:  
1
PLAY/x2  
→ Linear time counter (HMS) → Tape remaining time (REMAIN/RT) → Clock  
REW  
FF  
STOP  
STOP  
The indication above will also appear on the TV screen by pressing  
DISPLAY.They are switchable with REMAIN/COUNTER.  
ENTER  
To reset the linear time counter to “0H00M00S”  
PROG.  
The counter is automatically reset to “0H00M00S” when a cassette is  
ejected. If you want to reset at another point, such as the beginning of a  
new recording, just press COUNT RESET.  
Notes  
• The linear time counter does not work on non-recorded portions on the tape.  
• When the tape is ejected or the VCR is turned off, the display changes to  
clock.  
• If the tape rewinds back over “0H00M00S”, “–” appears in the VCR display.  
• The displayed time of the linear time counter is only an approximation.  
Tape Remaining Time  
To view the tape remaining time in the VCR display, select the  
tape length beforehand.  
Turn on the VCR and load a cassette.  
1
Press PROG. to display the MENU screen.  
2
Select “SET UP” using FF or REW, and press ENTER.  
3
Select the length of the tape.  
4
SET UP  
n
GTH  
PRESET  
PROGRAM  
T120: for a T-120 tape or shorter  
T160: for a T-140 or T-160 tape  
T180: for a T-180 tape  
TAPE LE  
SAP SET  
120 160 180  
On  
OFF  
OFF  
S IMULCAST  
ANTEnn  
LA GUAGE  
DS FO  
O
n
A
AUTO  
MA U  
n
n
EnG FRA ESP  
X
I
n
O
n
OFF  
PROG  
nD:  
E
(Continued)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Useful Functions in Tape Operation (continued)  
Press PROG. to exit.  
5
Press REMAIN/COUNTER.  
The remaining time (“RT - : - -”) appears in the VCR display.  
6
Notes  
• The displayed remaining time is an approximation.  
• The remaining time is calculated according to the tape speed (SP or SLP)  
and the cassette type.  
Index Search Function  
1
4
7
2
5
8
0
3
6
The VCR can find a point where a registered index signal is on a  
tape and play back for about 5 seconds. You can easily locate  
the desired program by inputting the index signal.  
9
100  
PLAY/x2  
3
2
REW  
FF  
STOP  
2
1
1
2
Index search  
Playback  
for 5 sec.  
Playback  
for 5 sec.  
Playback  
for 5 sec.  
Playback  
for 5 sec.  
Registering index signals  
Each time a recording starts, an index signal is automatically registered.  
To register it somewhere else, press INDEX f during recording.  
Note  
A certain interval is required between the index signals: more than 1 minute in  
the SP tape speed and more than 3 minutes in the SLP tape speed.  
Index search  
Load a cassette with the index signals registered.  
1
Press INDEX in the stop or playback mode.  
2
g
INDEX: To search in the reverse  
direction.  
0
H
00 00S  
M
INDEX  
f: To search in the forward  
direction.  
The VCR fast-forwards or rewinds the  
tape. When an index signal is found, the  
VCR plays back the tape for about 5  
seconds, and then resumes fast-  
I NDEX MARK  
forwarding or rewinding. This is repeated  
each time at an index signal.  
Press PLAY/x2 when the desired program is found.  
Normal playback starts.  
3
Notes  
• At the very beginning of the tape, the index search may not work properly.  
• If you registered the index signals on a tape recorded on another VCR, the  
recording may be blurred at the index point and the index search may not  
work properly.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Recording a TV Program  
This section explains the basic recording operation.  
Preparation  
• Select the video channel (3 or 4) or video input mode on the TV.  
• If you record cable channels via the cable box, finish the cable box set-up (pages 33-36), and turn on the  
cable box.  
Basic Recording  
Load a cassette with the safety tab attached.  
1
1
4
7
2
5
8
0
3
6
Press TV/VCR so that the “VCR”  
indicator appears in the VCR display.  
POWER  
SP  
2
3
VCR  
9
CH  
100  
2
5
4
Select a channel to record with  
CHANNEL on the VCR, or CH/TRK  
or number buttons on the remote  
control.  
If you see “L1” or “L2” in the VCR display, press I.SELECT so that the  
channel number appears.  
3
POWER  
SP  
PLAY/x2  
VCR  
REW  
FF  
STOP  
6
I.SELECT  
• If you record cable channels via the cable box, make the output  
channel number of the cable box or “L1” appear, depending on your  
connection. (See pages 11 – 13.)  
Press SP/SLP to select the  
recording tape speed.  
4
POWER  
SLP  
VCR  
CH  
SP: Suitable for general recording with  
better picture and sound quality.  
SLP: Suitable for tripling recording time, but with less picture and  
sound quality than using the SP tape speed.  
To record from other  
connected equipment  
In step 3, press I.SELECT to  
switch the display as follows:  
LI: To record via the LINE IN  
1 jacks on the rear panel.  
L2: To record via the LINE IN  
2 jacks on the front panel.  
REC  
TIMER  
Press REC on the VCR, or  
simultaneously press both REC on  
the remote control.  
5
6
POWER  
SLP  
REC  
VCR  
CH  
Recording starts.  
Press STOP to stop recording.  
Watching a TV program while  
recording another  
Recording off time setting  
By setting the recording off time, the recording  
stops and the VCR is turned off automatically.  
1) While recording, press TV/VCR to turn off  
“VCR” indicator.  
While recording, press REC on the VCR  
2) Choose another channel using the channel  
repeatedly to set the desired off time.  
selector on the TV.  
Each time you press REC, each half-hour up to  
about 4 hours later and “- : - -” appear cyclically.  
Skipping unnecessary scenes while  
recording  
PM  
POWER  
OFF  
SLP  
VCR  
REC  
CH  
Press PAUSE/STILL to stop recording  
momentarily. To resume recording, press  
PAUSE/STILL again.  
Notes  
• To cancel the recording in progress, press STOP.  
• If the VCR clock is not set, this function will not  
activate.  
Note  
The VCR automatically shifts to the stop mode if the  
recording pause mode continues for 10 minutes.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Timer Program Recording  
The programmable timer allows you to record up to 6 different programs over one month.  
Preparation  
• Select the video channel (3 or 4) or video input mode on the TV.  
• Make sure that the clock is set correctly (page 16).  
• Store the channels on the VCR (pages 17 and 18).  
• If you record cable channels, finish the cable box set-up (pages 33 – 36), and turn on the cable box.  
• If you record satellite channels, finish the DSS® satellite receiver set-up (pages 37 – 40), and turn on the  
DSS® satellite receiver.  
Timer Programming Procedure  
Example: To record cable channel 25 in the SP tape speed from  
9:30 p.m. until 10:00 p.m. on August 30. Today is August 25.  
Load a cassette with the safety tab attached.  
1
1
4
7
2
5
8
0
3
6
Press PROG. to display the MENU screen.  
2
3
4
9
100  
Select “PROGRAM” using FF or  
REW, and press ENTER.  
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
10  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
E D:  
n
–
–
–
–
–
–
REW  
FF  
PLAY/x2  
REW  
FF  
PLAY/x2,  
STOP  
STOP  
ENTER  
Move to the next using FF, and enter  
the channel number 25 by using  
PLAY/x2, STOP or number  
buttons.  
4
CANCEL  
SET UP  
On  
PRESET  
OFF SPD  
PROGRAM  
CH DATE  
25 – / –– – : –– – : –  
–
SLP  
2, 9  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–
–
–
–
–
–
–– – / –– – : –– – : –  
PROG  
EnD:  
• To record a cable program from the connected cable box:  
Enter the cable channel number by number buttons, PLAY/x2 or  
STOP.  
If your cable box is not remote-controllable, choose the desired  
channel (1 to 125) on the cable box.  
• To record a satellite program from the connected DSS® satellite  
receiver:  
Enter the satellite channel number (100 to 999) by number  
buttons, PLAY/x2 or STOP. (If a number 1 to 99 is entered, the  
VCR will record a TV/CATV program on the channel, not a  
satellite’s.)  
If your DSS® satellite receiver is not remote-controllable, choose the  
desired channel (100 to 999) on the DSS® satellite receiver.  
To make corrections:  
Press REW to move back to the item, or FF to forward.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Move to the next using FF, and set  
the recording date using PLAY/x2 or  
STOP.  
5
SET UP  
PRESET  
OFF SPD  
PROGRAM  
CH DATE  
O
n
SLP  
25 8 30 – : –– – : ––  
/
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
nD:  
–
–
–
–
–
The date changes as follows:  
…
…
→ 8/25 → 8/26 →  
→ 9/24 → WKLYSU →  
E
MO~FR ← WKLYSA ←  
…
[WKLYSU] [WKLYSA]: You can record TV programs on the same  
channel on the day and time every week.  
[MO~FR]: You can record TV programs on the same channel on the  
day and time Monday through Friday.  
Move to the next using FF, and set  
the hour and minutes of the  
recording start time.  
6
7
8
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
P
SLP  
25 8  
/
30 9  
:
30 M – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
E D:  
n
–
–
–
–
–
Move to the next, and set the  
recording off time.  
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
P
P
SLP  
25 8  
/
30 9  
:
30 M 10 : 00  
M
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
E D:  
n
–
–
–
–
–
Move to the next, and select the tape  
speed (SP) using PLAY/x2 or STOP.  
For the tape speed “AUTO (Auto Speed  
Select)”, see below.  
To set another program, press FF, and  
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
P
P
SP  
25 8  
/
30 9  
:
30 M 10 : 00  
M
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
D:  
–
–
–
–
–
select the next line pressing STOP.  
En  
Repeat steps 4 to 8.  
Press PROG..  
Now programming is completed.  
9
REC  
TIMER  
Press both TIMER simultaneously.  
The power turns off and the VCR enters  
the timer standby mode.  
10  
POWER  
TIMER  
Notes  
Auto Speed Select  
• Make sure that the tape length is selected correctly  
according to the tape used on the SET UP screen  
(page 23).  
• When the SLP tape speed is selected and the tape  
length is not sufficient to record the program to the  
end, the program cannot be recorded to the end.  
• The picture will be distorted when playing the part  
where the recording tape speed is switched from  
SP to SLP with the Auto Speed Select feature.  
If you are not sure the tape is long enough for  
timer program recording in the SP tape speed,  
set the recording tape speed to “AUTO”.  
Recording starts in the SP tape speed and the  
VCR automatically selects the tape speed to  
record the program to the end. If the tape length  
is not long enough, the tape speed automatically  
changes from SP to SLP.  
(Continued)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Program Recording (continued)  
Confirming the timer programs  
(in the timer standby mode)  
If a power failure occurs during the  
timer program recording (including  
VCR Plus+ C3 ® system recording  
(page 31))  
Press PROG..  
The screen for confirming will appear.  
• When a power failure has occurred, “- -:- -”  
appears in the VCR display. Since the  
programmed contents have been cleared,  
reset the clock and timer programming.  
• When power has failed for a short time, the  
colon of the current time display blinks. The  
programmed contents are not affected. Reset  
the clock.  
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
P
P
SP  
25 8  
/
30 9  
:
30 M 10 : 00  
M
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
nD:  
–
–
–
–
–
E
After about 30 seconds, the screen disappears.  
Overlaps of the programs  
Changing/cancelling the timer  
programs  
If two timer programs overlap, the recording start  
time of program 2 has priority over the recording  
off time of program 1.  
1) If the TIMER indicator is lit, press both TIMER  
to turn it off, and then turn the VCR on by  
pressing POWER.  
Overlapped portion (not recorded)  
Program 1  
(Start time)  
Program 2  
2) With steps 2 to 9, change the items.  
To cancel a program, select the program you  
want to cancel in step 4, and press CANCEL.  
The line is then cleared.  
(Start time)  
3) Press both TIMER to return to the timer  
standby mode.  
Recording or playback in the timer  
standby mode  
First press both TIMER to release the timer  
standby mode, and then press POWER to turn  
on the VCR. The VCR will be available for use.  
• Be sure to press both TIMER again to return  
the VCR to the timer standby mode after you  
are finished.  
Error indication  
The “E” (Error) indicator appears in the VCR  
display if you press both TIMER when:  
–– a cassette is not loaded.  
–– the loaded cassette has no safety tab.  
–– no timer program is set.  
In these cases, a recording can not be made.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
3
®
VCR Plus+ C system Set-up  
VCR Plus+ C3 ® system is a timer recording system for an easier programming that requires you only to  
enter a PlusCode® programming number assigned to a desired program. This section explains the  
necessary set-up to make VCR Plus+ C3 ® system recordings.  
Sample of a Guide channel chart from a local TV listing  
The flow chart below will give you an idea  
as to what must be done to use the VCR  
VCR Plus+® SYSTEM CHANNEL NUMBERS  
Plus+ C3 ® system feature.  
Broadcast  
channels  
Assigned  
channels  
Cable  
Assigned  
channels channels  
A & E........................39  
AMC.........................35  
(
)
3
6
KCRA NBC .................3  
Setting the Clock (page 16)  
(
)
KVIE PBS ...................6  
(
)
)
10 KXTV CBS ................10  
BET..........................57  
BRAV....................... 54  
CMTV.......................14  
CNBC.......................23  
CNN......................... 42  
↓
(
13 KOVR ABC ...............13  
(
)
19 KCSO SPAN .............19  
Cable Box Set-up (page 33)  
(
)
31 KRBK IND .................31  
(FOX)  
(IND)  
(IND)  
40 KTXL  
58 KSCH  
44 KBHK  
24 KCPM  
................40  
................ 25  
.................15  
...............24  
...............28  
.................27  
.................28  
↓
-
C SPAN....................28  
CUNY.......................29  
DIS...........................53  
ESPN....................... 34  
FAM......................... 47  
HBO......................... 33  
Storing Channels on the VCR  
(NBC)  
(NBC)  
KRNV  
(IND)  
(ABC)  
KGO  
4
(page 17)  
42 KFCB  
7
↓
VCR Plus+ C3 ® system Set-up  
↓
Sample of a Channel line-up chart from a cable-TV  
company  
VCR Plus+ C3 ® system Recording  
(page 31)  
CHANNEL LINE-UP CHART  
* With the VCR Plus+ C3 ® system, this video  
cassette recorder can automatically select the  
appropriate channel on your compatible cable  
box or satellite receiver. VCR Plus+, C3 and  
PlusCode are registered trademarks of  
Gemstar Development Corporation. The VCR  
Plus+ system is manufactured under license  
from Gemstar Development Corporation.  
Channel 2  
Channel 3  
Channel 4  
Channel 5  
Channel 6  
Channel 7  
Channel 8  
Channel 9  
ME/U  
8 WISH  
4 WTTV  
6 WRTV  
VCA/Local origination  
HOME BOX OFFICE  
A.P News Plus  
9 WGN.  
You must give the VCR the special  
numbers for guide channels (also called  
VCR Plus+® system channel numbers)  
assigned to each channel that you receive  
in your home. The VCR identifies the  
channel to be recorded by the guide  
channel number you enter.  
The guide channel numbers are published  
in TV guide magazine, selected local TV  
publications, or the channel guide from  
cable company. If you cannot find the  
numbers, call Gemstar’s customer service  
department at 1-800-4321-VCR.  
(Continued)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Plus+ C3 system Set-up (continued)  
®
Preparation  
• Select the video channel (3 or 4) or video input mode on the TV.  
• If you record cable channels, finish the cable box set-up (pages 33 – 36).  
• Prepare the list like below.  
Example  
Your home channel number (on the channel line-up  
chart supplied by cable companies)  
Guide channel number  
(on the TV Guide, local TV listings etc.)  
Station  
HBO  
ESPN  
AMC  
33  
34  
35  
7
Guide Channel Setting  
Press PROG..  
1
2
3
4
5
6
1
4
7
2
5
8
0
3
6
7
Select “PRESET” using FF or REW, and press ENTER.  
Select “CH MEMORY”using PLAY/x2 or STOP, and press ENTER.  
Set “TV/CATV” to “TV” or “CATV” using FF or REW.  
Press PROG. to return to the PRESET screen.  
Select “GUIDE CH” using PLAY/x2  
9
100  
2,4  
PLAY/x2  
REW  
FF  
STOP  
3,6,7  
ENTER  
SET UP  
PRESET  
PROGRAM  
GU IDE CH  
125  
H
OME CH  
or STOP, and press ENTER.  
125  
1
1
2
3
(the case of CATV mode)  
2
3
GU I DE CH  
HOME CH  
1,5,8  
T
E
O
SET  
CH PUSH 0~9 KEYS  
PROG  
nD:  
Enter channel numbers on the right of the guide channel  
numbers.  
7
Find a guide number you marked on the list using PLAY/x2 or STOP,  
and enter the corresponding home channel number if necessary by  
using number buttons.  
Example: To enter home channel number  
7 (HBO) with guide channel number 33  
assigned.  
SET UP  
PRESET  
PROGRAM  
GU IDE CH  
30  
HOME CH  
30  
31  
32  
7
31  
32  
33  
GU I DE CH  
HOME CH  
SET  
CH PUSH 0~9 KEYS  
In some areas, one channel may be  
assigned more than one guide channel  
number. In this case, enter the home  
channel number to each of the guide  
channel numbers.  
T
E
O
nD:  
PROG  
Notes  
• When your cable company  
changes the channel line-  
up, you must re-do this set-  
up for the channel.  
Press PROG. to exit.  
The set-up is all over and your VCR Plus+ C3 ® system recording is  
now available.  
8
• The VCR Plus+ C3 ® system  
feature does not work on  
programs from a connected  
DSS® satellite receiver.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
3
®
VCR Plus+ C system Recording  
After performing the VCR Plus+ C3 ® system set-up, you can easily program a recording simply by  
entering the PlusCode® programming number. The numbers are published in the TV listings of  
newspapers, TV guide magazine, etc.  
Preparation  
• Make sure that the clock is set correctly (page 16).  
• Load a cassette with a safety tab.  
For cable box users:  
• Finish the cable box set-up (pages 33 – 36), and turn on the cable box.  
For DSS® satellite receiver users:  
• This VCR cannot record satellite programs with the VCR Plus+ C3 ® system feature. To make an unattended  
recording of satellite programs, see “Timer Program Recording” (pages 26 – 28).  
Sample of TV program listing in a TV guide magazine  
5PM  
FAM  
HBO  
POPEYE  
725692  
Cartoon  
237945  
MAKING OF A CHAMPION  
A look at gymnast and Olympic hopeful Kim  
Zmeskal from novice to seasoned competitor.  
PlusCode®  
programming  
number  
N I K  
HEY DUDE  
Children 793571  
One of Ted’s teachers stays at the ranch.  
USA  
TBS  
MY TWO DADS  
GOOD TIMES  
586858  
2261858  
Comedy  
Comedy  
5:35  
VCR Plus+ C3 ® system Programming  
Press VCR Plus+.  
The VCR Plus+ screen appears.  
1
1
4
7
2
5
8
0
3
6
2
9
Enter a PlusCode® programming number.  
Example: To record a program with the  
PlusCode® programming number 36295  
(fictitious code).  
2
100  
SET UP  
PRESET  
PROGRAM  
7
VCR PLUS+  
PLUSCODE  
MODE  
REW  
FF  
36295  
–
PLAY/x2  
O
nCE MO~FR WKLY  
Press number button 3, 6, 2, 9 and 5.  
SPEED  
SLP AUT  
O
SP  
REW  
FF  
Confirm that the number is entered  
correctly.  
To correct a mistake, press CANCEL and  
E
TO S  
T
PLUSCODE  
PLAY/x2,  
STOP  
PROG.  
STOP  
PUSH 0~9 KEYS  
ENTER  
PROG  
EnD:  
enter the correct number.  
5
Select “MODE” using PLAY/x2 or  
STOP, and set the recording  
frequency.  
OnCE: To record once.  
DAILY(MO~FR):To record programs on  
the same channel at the same time  
Monday through Friday.  
CANCEL  
3
SET UP  
PRESET  
PROGRAM  
1
VCR PLUS+  
PLUSCODE  
MODE  
36295  
O
nCE MO~FR WKLY  
SPEED  
SLP AUT  
O
SP  
ENTER  
PROG  
EnD:  
WEEKLY: To record programs on the  
same channel at the same time on the  
same day every week.  
Select “SPEED” using PLAY/x2 or  
STOP, and set the recording tape  
speed.  
4
SET UP  
PRESET  
PROGRAM  
VCR PLUS+  
PLUSCODE  
MODE  
36295  
O
nCE MO~FR WKLY  
SPEED  
SLP AUT  
O
SP  
For AUTO speed, see page 27.  
ENTER  
PROG  
EnD:  
(Continued)  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Plus+ C3 system Recording (continued)  
®
Press ENTER.  
The program setting is now memorized.  
5
SET UP  
PRESET  
PROGRAM  
CH DATE  
O
n
OFF SPD  
P
P
SLP  
25 8  
/
30 9  
:
30 M 10 : 00  
M
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
–– – / –– – : –– – : ––  
PROG  
nD:  
–
–
–
–
–
• If your cable box is not remote-  
controllable, select the recording  
channel on the cable box beforehand.  
E
To set another program, repeat steps 1 to 5.  
6
REC  
TIMER  
To finish press the two TIMER  
buttons simultaneously.  
The VCR enters the timer standby mode.  
7
POWER  
TIMER  
Confirming the VCR Plus+ C3 ® system  
timer programs  
Recording or playback in the timer  
standby mode  
Before the VCR enters the timer standby  
mode (TIMER indicator not lit)  
1) Press PROG. to display the MENU screen.  
2) Press ENTER to select “PROGRAM”.  
Check the programmed data.  
First press both TIMER to release the timer  
standby mode, and then press POWER to turn  
on the VCR. The VCR will be available for use.  
• Be sure to press both TIMER again to return  
the VCR to the timer standby mode after you  
have finished.  
3) Press PROG. to exit.  
During the timer standby mode (TIMER  
indicator lit)  
Press PROG..  
The screen for confirming appears.  
After about 30 seconds, the screen disappears.  
Error indications  
If “FULL / CANCEL PROG?” message appears  
on the TV during programming, no more  
programs can be entered. If you want to add  
another, delete one existing program on the  
screen by using PLAY/x2 or STOP.  
If an incorrect PlusCode® programming number is  
entered, “ERROR CODE ENTERED” appears on  
the screen. Press CANCEL to clear the number  
and enter correct one.  
Canceling the VCR Plus+ C3 ® system  
timer programs  
1) If the TIMER indicator is lit, press both TIMER  
to turn it off, and turn on the VCR by pressing  
POWER.  
2) Press PROG. to display the MENU screen.  
3) Press ENTER to select “PROGRAM”.  
4) Select a program which you want to cancel.  
If “CLASH” message appears on the TV during  
programming, it tells you that two programs with  
the same recording start time have been entered.  
Correct either of the two programs as follows:  
1) Select the number of the program to correct by  
5) Press CANCEL.  
using PLAY/x2 or STOP.  
The line is cleared out.  
2) Correct the data, or clear out the line by  
pressing CANCEL and then press  
VCR Plus+ to enter a PlusCode® programming  
number.  
6) Press PROG. to exit.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Cable Box Set-up  
The VCR can directly control channel selecting of the connected cable box.  
Cable Box Control  
Connection Type  
Type A  
This VCR needs to be connected to a cable  
box equipped with an infrared wireless  
remote control. You can select cable  
channels from the cable box by operating  
this VCR.  
It is also possible to automatically change  
the cable channels according to your  
program setting in the timer program  
3
®
recording or VCR Plus+ C system recording.  
Placing the Cable Box  
Put the cable box on the top of the VCR as  
shown below. Do not block the sensor  
window.  
Cable box  
Type B  
Wall  
Front of the VCR  
Sensor window  
The infrared signals come out of the sensor  
window and the front of the VCR. Then they  
bounce off walls and other objects in the  
room and are received by the cable box.  
The VCR sends out infrared signals to your  
cable box even during timer program  
recording or VCR Plus+ C3 ® system  
recording.  
Type C  
A
A/B switch  
A
B
B
Cable box  
Notes  
• If the channels cannot be controlled properly  
because the infrared signal fails to reach the cable  
box, change the position of the box on the VCR so  
that it can receive the signal.  
• Keep the cable box turned on even while the VCR  
is in the timer program recording or VCR Plus+ C3 ®  
system recording.  
Type D  
Cable box  
(Continued)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cable Box Set-up (continued)  
Preparation  
• Select the video channel (3 or 4) or video input mode on the TV.  
• Set “TV/CATV” on the CH MEMORY screen to “CATV” (page 17).  
Cable Box Set-up  
Press PROG. to display the MENU screen.  
1
2
3
1
4
7
2
5
8
0
3
6
Number  
buttons  
Select “PRESET” using FF or REW, and press ENTER.  
9
100  
Select “CABLE BOX/DSS” using PLAY/x2 or STOP, and press  
ENTER.  
100  
I.SELECT  
REW  
FF  
PLAY/x2  
Select “NO” or “C.BOX” using FF or REW according to your  
connection type.  
4
REW  
FF  
PLAY/x2,  
STOP  
STOP  
NO:  
• Type A  
• Type C (A/B switch “A”)  
SET UP  
PRESET  
PROGRAM  
USE  
ENTER  
• Cable channels will be selected using  
CH/TRK on the remote control or  
CHANNEL on the VCR.  
nO C. BOX DSS  
POWER  
(CABLE BOX)  
CH  
→ Go to step 8.  
C.BOX: • Type B  
• Type C (A/B switch “B”)  
• Type D  
(CABLE BOX)  
SET UP  
PRESET  
PROGRAM  
PROG.  
USE  
OUTPUT CH  
CO TROL  
nO C.BOX DSS  
CH  
OFF  
3
n
O
n
→ Go to step 5.  
Select “OUTPUT CH” using PLAY/x2 or STOP, and enter  
5
6
either of the following according to your connection.  
(Example)  
Type B, C: the output channel number of  
your cable box using number buttons.  
(Usually 3 or 4. Check the rear of the  
cable box.)  
SET UP  
PRESET  
PROGRAM  
USE  
OUTPUT CH  
CO TROL  
nO C. BOX DSS  
CH  
OFF  
3
Type D: the line input mode “L1” using  
n
O
n
I.SELECT.  
Select “CONTROL” using PLAY/x2 or STOP, and set to “ON”  
or “OFF” using FF or REW.  
ON: if your cable box is remote-  
controllable.  
SET UP  
PRESET  
PROGRAM  
USE  
OUTPUT CH  
CO TROL  
BRA TYPE  
nO C. BOX DSS  
CH  
• Cable channels will be selected by CH  
(CABLE BOX) on the remote control.  
The VCR can change the cable  
channel to the desired one when timer  
recording or VCR Plus+ C3 ® system  
recording starts.  
3
n
OFF  
O
n
n
D
nO.  
1
PROG  
EnD:  
→ Go to step 7.  
OFF: if your cable box is NON remote-  
controllable.  
SET UP  
PRESET  
PROGRAM  
• Cable channels will be selected by the  
own channel selector of the cable box.  
The VCR channel should be set to the  
output channel of the cable box.  
USE  
OUTPUT CH  
nO C. BOX DSS  
CH  
3
CO  
n
TROL  
PROG  
OFF  
O
n
→ Go to step 8.  
EnD:  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Select “BRAND TYPE” using STOP, and enter a brand code  
of your cable box using number buttons. Refer to the table  
on the next page.  
7
Example: For a TOSHIBA cable box, identified by number 36.  
Cable box display  
SET UP  
PRESET  
PROGRAM  
VCR display  
USE  
OUTPUT CH  
CO TROL  
BRA TYPE  
nO C. BOX DSS  
3
CH  
n
OFF  
O
n
n
D
nO. 36  
PROG  
EnD:  
Cable channel number  
Make sure that the channel display of your cable box has changed to  
9. If not, try each brand code assigned to the brand of your cable box  
until the display changes to 9.  
If it still holds;  
• Relocate the cable box on the VCR.  
• Use each of digits from 1 to 91.  
Press PROG. to exit.  
8
Notes  
• If your cable channel does not change to 9 in step 7, the cable box will not  
be able to change channels in the timer recording. In this case, set  
“CONTROL” to “OFF” in step 6.  
• The cable box control is not compatible with the DSS® satellite receiver  
control.  
Buttons to control a remote-  
controllable cable box  
Once you complete the set-up for a remote  
controllable cable box, your cable box can be  
controlled by the following buttons on the remote  
control of the VCR.  
• POWER (CABLE BOX)  
To turn the cable box on or off.  
• CH (CABLE BOX)  
To select cable channels in the upper or lower  
direction. (not applicable to some brands of  
cable box.)  
• Number buttons (0 – 9)  
To select desired channels to record.  
• 100  
Some cable boxes require you to use this  
button as the enter button. Press this button  
after selecting the cable channel with number  
buttons.  
(Continued)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cable Box Set-up (continued)  
Table of cable box brand codes  
Brand name of your  
Brand code  
Brand name of your  
cable box  
Brand code  
cable box  
Telecaption  
Teleview  
Texscan  
Tocom  
77  
Toshiba  
Anvision  
36  
4, 6, 32, 42, 78  
18, 19  
1, 33, 34, 42, 48, 49, 73,  
91  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
1, 20, 21, 29, 42, 44, 63,  
88, 91  
Archer  
Unika  
1, 20, 21, 29, 42, 44, 63,  
88, 91  
Cablestar  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
Universal  
29, 42, 43, 44, 52, 63, 82,  
88  
7, 23, 45, 50, 84  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
6
Cableview  
Citizen  
Curtis  
30, 42, 44, 52, 63, 88  
30, 42, 44, 52, 63, 88  
8, 9, 56, 61  
1, 20, 21, 29, 42, 44, 63,  
88, 91  
Videoway  
Viewstar  
Diamond  
Warner Amex  
Zenith  
Eagle  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
7, 23, 45, 50, 84  
Eastern  
GC Brand  
Gemini  
26, 28  
30, 42, 44, 52, 63, 88  
4, 30, 85  
General Instrument 1, 2, 3, 4, 31, 34, 55, 85,  
91  
Hamlin  
Hitachi  
Jerrold  
14, 15, 28, 41  
31, 79, 80  
1, 2, 3, 4, 31, 34, 55, 85,  
91  
Macom  
31, 79, 80  
Magnavox  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
29, 32, 38, 39, 42, 44, 88  
29, 32, 38, 39, 42, 44, 88  
10, 11, 12, 13, 46  
10, 11, 12, 13, 46  
6, 8, 16, 17  
4, 13, 20, 21, 22, 23, 24,  
25, 26, 58, 62, 84  
5, 6, 78  
Movietime  
NSC  
OAK  
OAK Sigma  
Panasonic  
Philips  
Pioneer  
Pulsar  
Randtek  
30, 42, 44, 52, 63, 88  
13, 20, 21, 22, 23, 24, 25,  
26, 58, 62, 84  
6, 8, 16, 17  
RCA  
Realistic  
Regal  
44, 88  
14, 23, 41, 84  
26, 28  
29, 32, 38, 39, 42, 44, 88  
4, 6, 32, 42, 78  
8, 9, 56, 61  
Regency  
Rembrandt  
Samsung  
Scientific Atlanta  
Sheritech  
SL Mark  
Sprucher  
Stargate  
27  
4, 6, 32, 42, 78  
6, 8, 16, 17  
4, 6, 30, 32, 42, 44, 52, 63,  
78, 88  
Sylvania  
Teknika  
19  
74  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
DSS® Satellite Receiver Set-up  
The VCR can directly control channel selecting of the connected DSS® satellite receiver.  
DSS® Satellite Receiver Control  
This VCR needs to be connected to a DSS®  
satellite receiver equipped with an infrared  
wireless remote control. You can select  
satellite channels from the DSS® satellite  
receiver by operating this VCR.  
Connection Type  
Type A  
Satellite  
antenna  
RF IN  
RF OUT  
DSS® is registered trademark of DIRECTV,  
Inc., a unit of GM Hughes Electronics.  
3CH  
4CH  
DSS® satellite receiver  
RF IN  
It is also possible to automatically change  
the satellite channels according to your  
program setting in the timer program  
recording.  
RF OUT  
Placing the DSS® Satellite  
Receiver  
Type B  
Put the DSS® satellite receiver on the top of  
the VCR as shown below. Do not block the  
sensor window.  
Satellite  
antenna  
Incoming cable  
DSS® satellite receiver  
DSS® satellite receiver  
3CH  
4CH  
Wall  
LINE IN 1  
Front of the VCR  
Sensor window  
The infrared signals come out of the sensor  
window and the front of the VCR. Then they  
bounce off walls and other objects in the  
room and are received by the DSS® satellite  
receiver. The VCR sends out infrared  
signals to your DSS® satellite receiver even  
during timer program recording.  
LINE OUT  
Notes  
• If the channels cannot be controlled properly  
because the infrared signal fails to reach the DSS®  
satellite receiver, change the position of the  
receiver on the VCR so that it can receive the  
signal.  
• Keep the DSS® satellite receiver turned on even  
while the VCR is in the timer program recording.  
(Continued)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DSS® Satellite Receiver Set-up (continued)  
Preparation  
Select the video channel (3 or 4) or video input mode on the TV.  
DSS® Satellite Receiver Set-up  
Press PROG. to display the MENU screen.  
1
2
1
4
7
2
5
8
0
3
6
Number  
buttons  
Select “PRESET” using FF or REW,  
9
SET UP  
PRESET  
PROGRAM  
and press ENTER.  
100  
I.SELECT  
CL  
O
CK SET  
CH  
ME  
MORY  
REW  
FF  
CABLE BOX /DSS  
GU I DE CH  
PLAY/x2  
REW  
FF  
PROG  
En  
D:  
ENTER  
PLAY/x2,  
STOP  
STOP  
Select “CABLE BOX/DSS” using  
PLAY/x2 or STOP, and press  
ENTER.  
3
ENTER  
SET UP  
PRESET  
PROGRAM  
USE  
POWER  
(CABLE BOX)  
nO C. BOX DSS  
CH  
(CABLE BOX)  
PROG.  
PROG  
EnD:  
Select “DSS” using FF.  
4
5
SET UP  
PRESET  
PROGRAM  
USE  
OUTPUT CH  
nO C. BOX DSS  
CH  
OFF  
3
CO  
n
TROL  
PROG  
O
n
E
nD:  
Select “OUTPUT CH” using PLAY/x2 or STOP, and enter  
either of the following according to your connection.  
(Example)  
Type A: the output channel number of  
SET UP  
PRESET  
PROGRAM  
your DSS® satellite receiver using  
number buttons. (Usually 3 or 4. Check  
USE  
nO C. BOX DSS  
CH  
OUTPUT CH  
CO TROL  
the rear of the DSS® satellite receiver.)  
3
n
OFF  
O
n
Type B: the line input mode “L1” using  
I.SELECT.  
TO SET CH  
PUSH 0~9 KEYS  
PROG  
EnD:  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Select “CONTROL” using PLAY/x2 or STOP, and set to “ON”  
or “OFF” using FF or REW.  
6
ON: if your DSS® satellite receiver is  
remote-controllable.  
SET UP  
PRESET  
PROGRAM  
USE  
OUTPUT CH  
CO TROL  
BRA TYPE  
• Satellite channels will be selected by  
CH (CABLE BOX) on the remote  
control.  
nO C. BOX DSS  
CH  
3
n
OFF  
O
n
n
D
nO.  
1
The VCR can change the satellite  
channel to the desired one when timer  
recording starts.  
PROG  
EnD:  
→ Go to step 7.  
OFF: if your DSS® satellite receiver is  
NON remote-controllable.  
SET UP  
PRESET  
PROGRAM  
• Satellite channels will be selected by  
the own channel selector of the DSS®  
satellite receiver.  
The VCR channel should be set to the  
output channel of the DSS® satellite  
receiver.  
USE  
OUTPUT CH  
nO C. BOX DSS  
CH  
3
CO  
n
TROL  
PROG  
OFF  
O
n
EnD:  
→ Go to step 8.  
Select “BRAND TYPE” using STOP, and enter a brand code  
of your DSS® satellite receiver using number buttons. Refer  
to the table on the next page.  
7
Example: For a TOSHIBA DSS® satellite receiver, identified by  
number 99.  
SET UP  
PRESET  
PROGRAM  
VCR display  
USE  
OUTPUT CH  
CO TROL  
BRA TYPE  
nO C. BOX DSS  
3
CH  
n
OFF  
O
n
n
D
nO. 99  
PROG  
EnD:  
Make sure that the background of the above display has changed to  
the satellite program on channel 200. If not, relocate the DSS®  
satellite receiver on the VCR so that it can receive the infrared signal.  
Press PROG. to exit.  
8
Notes  
• If your satellite channel does not change to 200 in step 7, the DSS® satetllite  
receiver will not be able to change channels in the timer recording. In this  
case, set “CONTROL” to “OFF” in step 6.  
• The VCR Plus+ C3 ® system recording is not available on satellite channels.  
• The DSS® satellite receiver control is not compatible with the cable box  
control.  
(Continued)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DSS® Satellite Receiver Set-up (continued)  
Buttons to control a remote-  
Table of DSS® satellite receiver brand  
codes  
controllable DSS® satellite receiver  
Once you complete the set-up for a remote  
controllable DSS® satellite receiver, your DSS®  
satellite receiver can be controlled by the  
following buttons on the remote control of the  
VCR.  
• POWER (CABLE BOX)  
To turn the DSS® satellite receiver on or off.  
• CH (CABLE BOX)  
Brand name of your  
Brand code  
DSS® satellite receiver  
TOSHIBA  
RCA  
99  
98  
97  
SONY  
To select satellite channels in the upper or  
lower direction. (not applicable to some brands  
of DSS® satellite receiver.)  
• Number buttons (0 – 9)  
To select desired channels to record.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
MTS Broadcast Compatibility  
This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to  
your stereo system or stereo TV, you will experience the SAP or stereo sound.  
Preparation  
Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.  
Recording the SAP/Stereo Broadcast  
On the SET UP screen (page 15),  
1
SET UP  
n
GTH  
PRESET  
PROGRAM  
1
4
7
2
5
8
0
3
6
select “SAP SET” using PLAY/x2 or  
STOP, and set to “ON” using REW or  
FF.  
TAPE LE  
SAP SET  
120 160 180  
On  
OFF  
OFF  
9
S IMULCAST  
ANTEnn  
LA GUAGE  
DS FO  
O
n
A
AUTO  
MA U  
n
100  
n
EnG FRA ESP  
DISPLAY  
X
I
n
O
n
OFF  
PROG  
nD:  
E
PLAY/x2  
REW  
FF  
1
1, 2  
1
STOP  
Press PROG. to exit.  
2
3
Perform a recording.  
SAP (Second Audio Program broadcast):  
A separate audio program, usually broadcast in a second language with the  
main language.  
A.SELECT  
Selecting a sound  
Sounds recorded on the tape  
According to your setting of “SAP SET” on the SET UP screen, the sound is recorded onto different  
tracks of the tape as below. Set “SAP SET” to “ON” or “OFF” appropriately.  
Contents of recorded sound  
On-Screen Display  
(Press DISPLAY.)  
Setting of “SAP SET”  
on the SET UP  
screen  
Type of receiving  
broadcast  
Hi-Fi sound track  
Normal sound  
track (Mono)  
L
“SAP”  
not lit  
“STEREO”  
R
Regular  
(monaural audio)  
“ON” or “OFF”  
not lit  
MONO  
MONO  
MONO  
Stereo  
“ON” or “OFF”  
“ON”  
not lit  
lit  
lit  
not lit  
not lit  
lit  
MONO (MIXED)  
MONO  
STEREO  
MONO  
MONO  
MONO  
SAP  
MONO  
SAP  
Regular+SAP  
“OFF”  
lit  
MONO  
“ON”  
lit  
MONO  
Stereo+SAP  
“OFF”  
lit  
lit  
MONO (MIXED)  
STEREO  
Sounds in playback  
You can play SAP and/or stereo broadcasts with this VCR. Press A.SELECT to select a desired sound.  
Desired sound  
SAP sound  
L , R indicators in the VCR display  
R (right) is on.  
Sound output  
SAP  
Stereo sound  
Both R (right) and L (left) are on.  
Stereo  
Note  
When the TV is connected to the RF OUT terminal of the VCR, the output sound is monaural.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECORDING  
Simulcast Recording  
When TV program such as MTV, HBO or MAX is being simulcast in FM stereo in your area, the VCR can  
also record the simulcast sound from an FM stereo tuner or receiver onto the Hi-Fi track and normal  
track.  
Preparation  
• Connect the TV and stereo system to the VCR as below.  
• Turn on the connected FM tuner and tune to the station for the simulcast program.  
To the FM antenna terminal  
Broadcast or  
incoming cable  
AUDIO OUT  
AUDIO IN  
AUDIO OUT  
LINE IN 1 AUDIO  
Simulcast Recording  
On the SET UP screen (page 15),  
1
SET UP  
n
GTH  
PRESET  
PROGRAM  
1
4
7
2
5
8
0
3
6
select “SIMULCAST” using PLAY/x2  
or STOP, and set to “ON” using REW  
or FF.  
TAPE LE  
SAP SET  
120 160 180  
3
On  
OFF  
OFF  
S IMULCAST  
ANTEnn  
LA GUAGE  
DS FO  
9
O
n
A
AUTO  
MA U  
n
100  
n
EnG FRA ESP  
X
I
n
O
n
OFF  
4
5
PROG  
nD:  
E
PLAY/x2  
REW  
FF  
1
6
1
Press PROG. to exit.  
2
3
STOP  
Select the desired channel using CHANNEL on the VCR or  
CH/TRK on the remote control.  
If you use a cable box, select a desired channel on the box.  
1, 2  
Select the recording tape speed using SP/SLP.  
Press REC to start recording.  
4
5
6
Press STOP to stop recording.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDITIONAL INFORMATION  
Multi Brand Remote Control  
The remote control can be compatible with various brands of TV by setting their control codes. The  
TOSHIBA code has initially been set to control TOSHIBA TVs.  
Setting Control Codes  
1
Press TV to set the remote control operating your TV.  
1
POWER  
1
4
7
2
5
8
0
3
6
CH/TRK  
While holding down PROG., enter  
the two digits of your TV’s brand  
code (listed on page 44) using  
number buttons.  
2
Hold down.  
Example  
9
PROG.  
TV VOL  
100  
Number  
buttons  
100  
0
2
PLAY/x2  
Release PROG..  
3
4
DISPLAY  
REW  
FF  
STOP  
Point the remote control at your TV and use each button listed  
below to make sure that your TV is operated correctly.  
I.SELECT  
ENTER  
POWER  
CH/TRK  
To turn the TV on or off.  
To select TV channels in the upper or lower  
direction.  
2, 3  
TV VOL  
To adjust the sound level.  
I.SELECT  
To select an external source such as a VCR.  
Number buttons To select TV channels. When selecting channels  
1 to 9, first enter 0 and then the desired number.  
100  
DISPLAY  
ENTER  
To substitute for 100 channel key.  
To turn on or off TV’s screen display.  
To use for the TV’s ENTER key.  
Important  
Some TVs may not respond to all the operations above, or  
may not be operated at all with this remote control. In this  
case, operate your TV with its own remote control.  
Notes  
• For some brands, several control codes (brand codes) are allocated. Try  
each of them until the buttons work on your TV.  
• If you replace the remote control’s batteries, set the brand code again.  
(Continued)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Multi Brand Remote Control (continued)  
Table of Brand Codes  
Brand name of your TV  
Brand name of your TV  
Brand Code  
Brand Code  
Toshiba  
Bell & Howell  
Carver  
01  
09  
10  
03  
12  
Proton  
11  
14  
Pulser  
Quasar  
Radio Shack  
RCA  
07, 15  
Celebrity  
Citizen  
13  
02  
Curtis Mathes  
Dumont  
Electro band  
Emerson  
Fisher  
09, 12  
Realistic  
Runco (NEC)  
Samsung  
Sanyo  
09, 11, 13  
14  
14  
03  
11, 12  
09, 11  
09  
09  
Scotch  
11  
GE  
02, 07, 11  
Scott  
11  
Gibralter  
Goldstar  
Hallmark  
Hitachi  
14  
Sears  
01, 02, 09, 10, 11  
11  
Sharp  
08, 13  
11  
Sony  
03  
06  
Soundesign  
Supreme  
Sylvania  
Tandy  
11  
Infinity  
10  
03  
JBL  
10  
10  
JCB  
03  
08  
JVC  
05  
Technics  
Techwood  
Teknika  
TMK  
07, 15  
LXI  
01, 02, 09, 10, 11  
07  
Magnavox  
Marantz  
Megatron  
Memorex  
MGA  
10  
04, 10, 12  
10  
11  
06, 11  
Victor  
05  
04, 09, 11  
Vidikron  
Vidtech  
Wards  
10  
04, 11  
11  
Midland  
Mitsubishi  
Motorola  
MTC  
02, 07, 14  
10, 11, 13  
14  
04, 11  
Zenith  
08  
12  
NAD  
01, 11  
Nikko  
11  
Optimus  
Optonica  
Panasonic  
Penney  
Philco  
09  
08  
07, 10, 15  
01, 02, 07, 11, 12  
10  
10  
16  
12  
07  
02  
Philips  
Pioneer  
Princeclub  
Prism  
Proscan  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDITIONAL INFORMATION  
Before Calling Service Personnel  
Check the following symptoms before requesting servicing.  
No power.  
The desired sound is not heard, such as  
SAP, stereo, or regular sound.  
• The power cord is not plugged in.  
• Setting of sounds is not correct.  
– Plug the power cord into the outlet firmly.  
– Select a desired sound using A.SELECT.  
(page 41)  
Although the power is on, the VCR will  
not work.  
Noise is present in the Hi-Fi sound being  
played.  
• There is no cassette.  
– Load a cassette. (page 19)  
• Tracking is not set appropriately.  
– Adjust the tracking manually. (page 20)  
The clock does not work.  
• There has been a power failure.  
– Reset the clock. (page 16)  
The timer recording function does not  
work.  
The timer does not work properly.  
• There is an error in programming.  
• The time is incorrect.  
– Reset the timer recording program. (page 26)  
– Set the clock correctly. (page 16)  
• There is no cassette in the VCR.  
– Load a cassette with the safety tab attached.  
(page 19)  
The picture does not appear on the TV  
screen.  
• The cassette does not have the safety tab.  
– Use another cassette with a safety tab or  
cover the hole with adhesive tape. (page 19)  
• The video channel or video input mode is not  
set correctly.  
– Set the TV channel to the video channel (3 or  
4) or set the video input mode on the TV.  
(page 11)  
• The timer indicator is not displayed.  
– Press both TIMER simultaneously. (page 27)  
• The TV signal is weak.  
– Adjust the antenna direction or use an  
optional antenna booster.  
• There has been a power failure.  
– Reset the clock. (page 16)  
• The cable box set-up has not been set correctly.  
– Make the set-up correctly. (page 34)  
• The power cord is not plugged in.  
– Plug the power cord into the outlet firmly.  
• The cable box is not turned on.  
– Turn on the cable box.  
The picture does not appear on the TV  
screen during recording and playback.  
The VCR Plus+ C3 ® system recording  
cannot be done.  
• The video channel or VCR mode is not set  
correctly.  
– Press TV/VCR to select the VCR mode and  
set the TV channel to 3 or 4. (pages 11, 25)  
• The guide channel numbers are not set up  
correctly.  
– Make the guide channel number setting.  
(page 29)  
The VCR does not record.  
• The loaded cassette has no safety tab.  
– Use a cassette with a safety tab or cover the  
hole with adhesive tape. (page 19)  
• The cable box is not turned on when the  
channel comes in the VCR via the cable box.  
– Turn on the cable box.  
The playback picture is poor.  
• The cable box set-up has not been set correctly.  
– Make the set-up correctly. (page 34)  
• Tracking is not set appropriately.  
– Adjust the tracking manually. (page 20)  
• The timer indicator is not displayed.  
– Press both TIMER simultaneously. (page 32)  
• The video heads are dirty.  
– Clean the video heads with a commercially  
available cleaning tape.  
(Continued)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Calling Service Personnel (continued)  
The remote control does not work  
properly.  
• The batteries are exhausted.  
– Replace all batteries. (page 10)  
• The remote control is operated beyond the  
operating range.  
– Make sure the remote control is within 30° of  
the remote sensor on the VCR. (page 10)  
• Too far from the VCR.  
– Use the remote control within 7 m from the  
front of the VCR. (page 10)  
• An obstacle may be in the way of the operation.  
– Remove the obstacle.  
• The operating mode of the remote control is not  
set correctly.  
– Press VCR or TV depending on the  
equipment you want to operate. (pages 14, 43)  
The cassette is ejected immediately after  
it is loaded.  
• The cassette was inserted with the label side  
not paralleling the compartment.  
– Reload it carefully. (page 19)  
The cassette does not go into the cassette  
compartment.  
• There is already a cassette in the VCR.  
– Eject the cassette and reload the new one.  
(page 19)  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Power supply:  
120 V AC, 60 Hz  
Power consumption:  
External dimensions:  
Mass:  
19 W  
430 × 96.5 × 281 mm (W.H.D.)  
3.8 kg  
Channels received:  
VHF: Channels 2–13  
UHF: Channels 14–69  
CATV: Channels 1–125  
UHF/VHF: 75 Ω F type connector  
Standard NTSC  
Antenna input/output terminals:  
Signal system:  
Recording/Playback system:  
Recording: VHS format (SP, SLP)  
Playback: VHS format (SP, LP, SLP)  
Cassette:  
Video cassette with  
mark  
Tape speed:  
SLP: 11.1 mm/s, SP: 33.4 mm/s  
Video recording/playback time:  
SLP: 480 minutes, SP: 160 minutes (When T-160  
video cassette is used.)  
Fast forward time:  
High speed rewind time:  
Video input:  
Within approx. 80 s (When T-120 video cassette is  
used.)  
Within approx. 54 s (when T-120 video cassette is  
used.)  
1 V (p-p), 75 Ω, unbalanced, negative sync., pin  
jack  
Video output:  
1 V (p-p), 75 Ω, unbalanced, negative sync., pin  
jack  
Audio input:  
Line input: 308 mV (rms), more than 47 kΩ, pin  
jack  
Audio output:  
Line output: 308 mV (rms), less than 4.7 kΩ, pin  
jack  
Audio frequency range (Hi-Fi):  
Audio dynamic range (Hi-Fi):  
Utilization conditions:  
20 Hz – 20 kHz  
90 dB  
Temperature: 5°C to 40°C  
Humidity: less than RH 80%  
Accessories  
Antenna cable ....................................... 1  
Remote control..................................... 1  
Batteries (AAA) .................................... 2  
Designs and specifications are subject to change without notice.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY TOSHIBA VIDEO  
CASSETTE RECORDER  
Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc. (“THI”) make the following limited warranties.  
These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original  
consumer purchaser and to no other purchaser or transferee.  
Limited Ninety (90) Day Warranty  
Your Responsibility  
TACP/THI warrant this product against defects in  
materials or workmanship for a period of ninety days  
after the date of original retail purchase. During this  
period, TACP/THI will repair a defective product or  
part, without charge to you. You must deliver the entire  
producttoaTACP/THIAuthorizedServiceStation.You  
areresponsibleforalltransportationandinsurancecharges  
for the set to and from the Authorized Service Station.  
The above warranties are subject to the following  
conditions:  
(1) You must retain your bill of sale or provide other  
proof of purchase.  
(2) You must notify an Authorized TACP/THI Service  
Station within thirty (30) days after you discover a  
defective product or part.  
(3) All warranty servicing of this product must be made  
by an Authorized TACP/THI Service Station.  
(4) These warranties are effective only if the product is  
purchased and operated in the U.S.A or Puerto Rico.  
(5) Labor service charges for set installation. Set up,  
adjustment of customer controls and installation of  
repair or antenna systems are not covered by this  
warranty.Receptionproblemscausedbyinadequate  
antenna systems are your responsibility.  
(6) Warranties extend only to defects in materials or  
workmanship as limited above and do not extend to  
anyproductorpartswhichhavebeenlostordiscarded  
by you or to damage to products or parts caused by  
misuse, accident, damage caused by Acts of God,  
such as lightning or fluctuations in electric power,  
improper installation, improper maintenance or use  
in violation of instructions furnished by us; or to  
units which have been altered or modified without  
authorizationofTACP/THIortodamagetoproducts  
or parts there of which have had the serial number  
removed, altered, defaced or rendered illegible.  
(7) At you option, after the warranty period has expired  
in the U.S.A. Call (800)-631-3811 to receive  
informationconcerninganexchangeprice.Payment  
must be enclosed with the product in the form of a  
certified check or money order and forward your  
product to:  
Limited One (1) Year Warranty  
TACP/THI further warrant the parts in this product  
against defects in materials or workmanship for a period  
of one (1) year after the date of original retail purchase.  
During this period, TACP/THI will replace a defective  
part without charge to you, except that if a defective part  
is replaced after ninety (90) days from the date of the  
original retail purchase, you pay labor charges involved  
in the replacement. You must also deliver the entire  
producttoaTACP/THIAuthorizedServiceStation.You  
areresponsibleforalltransportationandinsurancecharges  
for the set to and from the Authorized Service Station.  
Rental Units  
The warranty for rental units begin with the first rental or  
thirty (30) days from the date of shipment to the rental  
firm, whichever comes first.  
Commercial Units  
Productssoldandusedforcommercialusehavealimited  
ninety (90) day warranty for all parts and labor.  
Owner’s Manual and Demographic Card  
You should read the owner’s manual thoroughly before  
operating this product. You should complete and mail  
the enclosed Demographic card within ten (10) days  
after you, or the person who has given you this product  
as a gift, purchased this product. This is one way to  
enable TACP/THI to provide you with better customer  
service and improved products. Failure to return the card  
will not affect your rights under this warranty.  
Toshiba America Consumer Products Inc.  
Returns Center  
1420C Toshiba Dr.  
Lebanon, TN 37087  
(8) Uponreceiptwewill,atouroption,replaceyourunit  
with a new or refurbished unit of equal value.  
Featuresmaynotbeidenticaltoyouroriginalproduct.  
(9) Physically damaged units are not acceptable for  
repair or exchange in or out of warranty and will be  
returned as received.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY (continued)  
How to Obtain Warranty Service  
(1)Refer to the troubleshooting guide in your owner's manual. This check list may solve your problem.  
(2)Call the TACP toll free number 800-631-3811 within (30) days after you find a defective product or part.  
(3)Arrange for the delivery of the product to the Authorized TACP/THI Service Station. Products shipped to the  
Service Station must be insured and safely and securely packed, preferably in the original shipping carton, and  
a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be enclosed.  
In the Continental United States contact:  
In Hawaii contact  
Toshiba Hawaii  
327 Kamakee Street,  
Honolulu, HA 96814  
(808)-591-8377  
Toll Free  
800-631-3811  
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular  
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any  
warrantiesimpliedbystatelawasherebylimited, theforegoingwarrantyisexclusiveandinlieuofallotherwarranties,  
guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of  
any parts. In no event shall TACP/THI be liable for consequential or incidental damages.  
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties  
in any manner whatsoever. The time within action must be commenced to enforce any obligation of TACP/THI arising  
under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90)  
days from the date you discover or should have discovered the defect. This limitation does not apply to implied  
warranties arising under state law. This warranty gives you specific legal rights and you may also have other rights  
which may vary from state to state. Some states do not allow limitation on how long an implied warranty lasts, when  
an action may be brought or the exclusion or limitation of incidental or consequential damages, so the above provisions  
may not apply to you.  
ATTENTION CANADIAN CONSUMERS:  
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed and  
forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their  
warranty. Product must be purchased from an Authorized Canadian Dealer.  
Products purchased in the U.S.A and used in Canada are not covered by these warranties.  
IMPORTANT: PACKING AND SHIPPING INSTRUCTION  
WhenyousendtheproducttoaServiceStation, youshouldusetheoriginalcartonboxandpackingmaterial, theninsert  
the original carton box containing the unite into another carton, using more packing material.  
Printed in China  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Technicolor Thomson CRT Television 1 4 M S 1 5 F T User Manual
Toshiba Computer Accessories GN 2010 User Manual
Toshiba DVD Player D RW2 User Manual
Toshiba DVR KV DVR User Manual
Toshiba Laptop U200 ST2091 User Manual
TP Link Switch TL SL2109 User Manual
Tripp Lite Computer Drive U239 000 R User Manual
Turbo Chef Technologies Microwave Oven FSB10036 User Manual
ViewSonic Personal Computer VS13426 User Manual
Virgin Mobile Cell Phone 836182001579 User Manual