Video Cassette Recorder
W-7 0 4 C
OWNER’S MANUAL
REV
FF
PLAY
STOP
POWER
EJECT
PROG.TV
PAUSE/STILL
REC
This publication is printed
on recycled paper
70971857
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to ship
your VCR. For maximum protection, repack the set as it was originally packed at the factory.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit.
Do not leave rubber or plastic products touching the unit for a long time. They will mar the
finish.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the VCR is exposed to such a change in temperature, moisture may condense on the
cylinder inside, one of its most crucial internal parts. To prevent the VCR from possible
damage, do not use the unit for at least 2 hours when there is an extreme or sudden change
in temperature.
Compatibility
This video cassette recorder (VCR) is compatible with any other VCR bearing the
mark. HQ VHS equipment is also compatible with existing, non-HQ VHS equipment.
Copyright
It is permissible to record television programs, film, video tapes and other material only in the
event that third party copyrights and other rights are not violated.
®
As an ENERGY STAR Partner, TOSHIBA has determined that this product or
®
product model meets the ENERGY STAR guidelines for energy efficiency.
In the spaces provided below, record the Model and Serial No. located at the rear of your video
cassette recorder.
Model No.
Serial No.
Retain this information for future reference.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS
GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect
you if you observe the following procedures for installation, use and servicing. This unit is
fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow all
the operating and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating
instructions.
3. Grounding or Polarization
This product may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface. This
productshouldnotbeplacedinabuilt-ininstallationsuchasabookcaseorrack
unless proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
5. Heat
Theproductshouldbesituatedawayfromheatsourcessuchasradiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
7. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from
the product.
9. Overloading
Donotoverloadwalloutlets;extensioncords,orintegralconveniencereceptacles
as this can result in a risk of fire or electric shock.
10. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system
is grounded so as to provide some protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
11. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
12. Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
13. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
14. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
15. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
S3125A
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
16. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
19. Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
INTRODUCTION
Variable Speed Playback.................. 21
Provides important notes and general
explanation of the VCR, including names of the
buttons, jacks, etc.
• Picture Search
• Still Picture
• Slow-motion Picture
• Frame Advance
• Double Speed Playback
• Shuttle Dial Operation
SAFETY PRECAUTIONS .................... 2
IMPORTANT PRECAUTIONS.............. 3
IMPORTANT SAFETY
INSTRUCTIONS ................................... 4
Useful Functions in Tape
Operation ........................................... 23
Contents .............................................. 7
Identification of Controls ................... 8
• Counter Function
• Tape Remaining Time
• Index Search Function
• Front Panel
• Remote Control
• VCR Display
• Rear Panel
RECORDING
Explains recording functions.
Recording a TV Program .................. 25
PREPARATION
• Watching a TV program while
recording another
• Recording off time setting
Explains what you need to do before operating
the VCR.
How to Use the Remote Control ...... 10
Connections ...................................... 11
Auto Set Up ....................................... 14
Timer Program Recording ............... 26
VCR Plus+ C3 ® system Set-up ......... 29
VCR Plus+ C3 ® system Recording .. 31
Cable Box Set-up .............................. 33
DSS® Satellite Receiver Set-up ........ 37
MTS Broadcast Compatibility .......... 41
Simulcast Recording ........................ 42
Initial Settings Using On-screen
Display ............................................... 15
• Setting the Language
• Optional settings on the SET UP
screen
• Setting the Clock
Storing Channels on the VCR .......... 17
Video Cassette Use .......................... 19
ADDITIONAL INFORMATION
Multi Brand Remote Control ............ 43
Before Calling Service Personnel ... 45
Specifications ................................... 47
Accessories....................................... 47
CANADIAN WARRANTY ................... 48
PLAYBACK
Explains variable functions concerning
playback.
Playback ............................................ 20
• 19µ HEAD
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Identification of Controls
See the page in
for details.
This manual shows the names of buttons in italics.
Front Panel
CHANNEL
25
EJECT
19
15
PLAY
STOP
20
20
Cassette compartment
19
POWER
REV
(
FWD
)
PLAY
STOP
POWER
c
EJECT
SHUTTLE
CHANNEL
22
LINE IN
2
PAUSE/STILL
REC
LINE IN 2
VIDEO
L-MONO-AUDIO-R
VIDEO jack
PAUSE/STILL
Remote sensor
21
10
LINE IN 2 AUDIO
(L/MONO, R) jacks
VCR display
9
REC
25
Remote Control
To operate this VCR.
To operate your TV.
VCR
TV
14
VCR
TV
POWER
POWER
CH/TRK
15
25
43
1
4
2
5
8
0
3
6
9
Number buttons
25
25
23
CH/TRK
100
18
I.SELECT
REMAIN/COUNTER
DISPLAY
7
I.SELECT
TV VOL
TV/VCR
43
25
TV VOL
100
REMAIN/
COUNTER
DISPLAY
SP/SLP
COUNT RESET
TV/VCR
TIMER
23
25
25
REC
COUNT RESET
23
SP/SLP
TIMER
27
PLAY/x2
REC
PLAY/x2 *
20
REW
FF
CURSOR
STOP
REW *
20
FF *
20
SLOW
PAUSE/STILL
SLOW 21
PAUSE/STILL
21
PROG.
ENTER
CANCEL
19µ/
+
VCR Plus
A.SELECT
STOP *
PROG.
CH
15
20
EJECT
INDEX
POWER
ENTER
19µ
20
VCR Plus+ 31
15
CABLE
BOX
EJECT
19
28
POWER (CABLE BOX)
35
CANCEL
CH (CABLE BOX)
35
A.SELECT
41
INDEX
24
* These buttons are used to control the
cursor on the screen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Display
VCR indicator
Timer recording indicator
REMAIN indicator
Cassette indicator
OFF indicator
POWER indicator
AM PM
REMAIN
POWER
L
Hi-Fi (L/R) indicators
L: Left channel
R:Right channel
off: Normal track
SLP
OFF
R
VCR
TIMER
REC
DT
CH
H
M
S
Multifunctional indicator
DT (Digital Auto Tracking) indicator
Channel indicator
REC (Recording)
indicator
Tape speed indicator
(SP/SLP)
Tape running direction/speed indicator
Rear Panel
LINE OUT VIDEO jack
LINE IN 1 VIDEO jack
RF IN (FROM ANT.) terminal
To wall outlet
LINE IN 1 AUDIO jacks (L, R)
CH selector (3/4)
RF OUT (TO TV) terminal
LINE OUT AUDIO jacks (L, R)
LINE IN 1 AUDIO (Rear), 2 (Front) jacks
If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same
sound is recorded on both L and R on the Hi-Fi track.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
How to Use the Remote Control
This section explains how to get ready for remote control operation.
Setting up the Remote Control
Open the battery compartment lid on the
rear panel.
1
Install 2 batteries (“AAA” size) following
the polarity diagrams.
2
3
4
Close the battery compartment lid.
Point the remote control at the VCR and press the buttons within the operating range.
Distance: within about 7 m from the front of the remote sensor
Angles:
within about 30˚ in every direction
Notes on batteries
Caring for the remote control
• The life of the batteries is about 1 year
depending on the conditions of use.
• If the remote control does not operate correctly,
• Do not expose the remote sensor of the VCR
to a strong light source such as direct sunlight
or illumination (especially high-frequency
lighting) when using the remote control.
replace all batteries with new ones.
• Be careful not to spill water on the remote
control or to place it on anything wet, and avoid
sharp impacts.
• If the remote control is not to be used for a
long period of time, remove the batteries to
avoid possible damage from battery corrosion.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Connections
Before you use this VCR, it is necessary to connect it to your TV. Several ways of connecting are
available depending on your use of TV or cable box. Select one which is applicable to your equipment.
Antenna/VCR/TV Connection
Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the
VCR.
1
Connect the RF OUT terminal to the TV.
2
VHF/UHF combinaion
antenna
VHF antenna
only
UHF antenna
only
1
IN
(FROM ANT.)
VHF/UHF
2
OUT
(TO TV)
VHF UHF
Setting the VCR Output Channel
When the VCR is connected in this way, the VCR sends the output
signals to channel 3 or 4 on your TV. Set the output channel
selector (CH selector) of the VCR to “3” or “4”, whichever is vacant
in your area.
Antenna splitter
(not supplied)
AUDIO/VIDEO Connections
The AUDIO/VIDEO jacks are also available to connect your TV.
When connected your TV using the
AUDIO/VIDEO OUT jacks
To watch video pictures, set the video input mode on
your TV. For the video input mode, refer to the
manual of your TV.
LINE OUT VIDEO
VIDEO IN
LINE OUT AUDIO AUDIO IN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Cable Connection
Choose one of the below according to your usage of the cable box.
This set-up will enable you to:
– record an unscrambled channel.
– watch an unscrambled channel while recording
it.
– record an unscrambled channel while watching
another (only when you connect a cable-
compatible TV).
Incoming cable
You will need to:
• select TV channel 3 or 4 to receive video
signals. (See page 11.)
• to record a channel while watching another,
press TV/VCR on the remote control to turn off
the “VCR” indicator in the VCR display and
select a desired channel on the TV (only when
you connect a cable-compatible TV).
This set-up will enable you to:
– record an unscrambled channel.
– watch an unscrambled channel while recording
it.
– record an unscrambled channel while watching
another (scrambled or unscrambled).
Cable Box
IN
OUT
You will need to:
Incoming cable
• set TV channel to the output channel of the
cable box.
• turn on the cable box and select cable channel
3 or 4 according to the output channel of the
VCR.
• to record a channel while watching another,
press TV/VCR on the remote control to turn off
the “VCR” indicator in the VCR display and
select a desired cable channel on the cable
box.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
This set-up will enable you to:
– watch an unscrambled or scrambled channel
while recording it.
– record any channels through the cable box.
Cable Box
You will need to:
• set TV channel 3 or 4 to receive video signals.
(See page 11.)
IN
OUT
• set VCR channel to the output channel of the
cable box, and select a desired cable channel
on the cable box.
• while the VCR is turned off or the “VCR”
indicator is not lit in the VCR display, set TV
channel to the output channel of the cable box.
A/B switch
A
This set-up will enable you to:
A
B
– watch an unscrambled or scrambled channel
while recording it.
B
Cable Box
– record an unscrambled channel while watching
another unscrambled channel (only when you
connect a cable-compatible TV).
• A/B switch “A”: record and watch an
unscrambled channel which
comes bypassing the cable box.
• A/B switch “B”: record and watch a scrambled
or unscrambled channel coming
through the cable box.
This set-up will enable you to:
– watch or record a channel through the cable
box via the LINE IN 1 (AUDIO/VIDEO) jacks.
You will need to:
• press I.SELECT so that the VCR display
shows “L1”.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Auto Set Up
The Auto Set Up function automatically sets the tuner channels and clock when power is first connected
to the VCR.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press I.SELECT so that the channel number will appear if “L1” or “L2” is displayed in the VCR display.
• Press VCR to set the remote control operating the VCR.
Auto Set Up
Connect the antenna cable to the VCR (see page 11). Then connect the VCR’s power
plug to an AC outlet.
1
“Auto” flashes in the VCR display as the VCR automatically tunes in all active stations.
When Auto Set Up is completed successfully, the current time will be displayed.
VCR display
VCR display
PM
Auto Set Up completed.
Tuning in progress.
• If the VCR fails to set the clock, “– : – –” will be displayed. Set the clock manually. (Refer
to “Setting the clock” on page 16.)
Notes
• If you press the CANCEL button, the Auto Set Up is cancelled.
• If Auto Set Up is not perform successfully, perform the clock and Tuner Channel procedures manually
(page 16 to 18).
• If, however, you want to add or delete channels, refer to “Adding or erasing channels” on page 18.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Initial Settings Using On-screen Display
Language selection must be set first when the VCR is first plugged in, or after it encounters a power
failure. You can also easily make necessary settings using the on-screen displays.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press VCR to set the remote control operating the VCR.
Setting the Language
VCR
POWER
Press POWER to turn on the VCR.
1
1
4
7
2
5
8
0
3
6
Press PROG..
The following screen appears on the TV.
2
3
4
9
SET UP
PRESET
PROGRAM
100
EnGL I SH
FRAnÇA I S
ESPAñOL
REW
FF
PLAY/x2
REW
FF
PROG
nD:
E
PLAY/x2,
STOP
STOP
ENTER
Select the language using PLAY/x2
(CURSOR ) or STOP (CURSOR
) , and press PROG..
MEnU
PROG.
The screen turns to the MENU screen.
SET UP
PRESET
PROGRAM
PROG
En
D:
ENTER
Press PROG. to return to the normal TV screen.
Optional settings on the SET UP screen
Other optional settings can be made. Press ENTER while “SET UP” is selected on the
MENU screen. The screen turns to the SET UP screen.
Page 23
SET UP
n
GTH
PRESET
PROGRAM
Page 41
Page 42
TAPE LE
SAP SET
120 160 180
On
OFF
OFF
S IMULCAST
ANTEnn
LA GUAGE
DS FO
O
n
A
AUTO
MA U
n
With “AUTO” set, a TV broadcast will appear via the TV tuner after
playback.
Move down here, and set to “AUTO” or “MANU”.
If you made the Audio/Video connection (page 11), set to “MANU”.
n
EnG FRA ESP
X
I
n
O
n
OFF
PROG
nD:
E
To change the language, move down here and set to the desired one.
With “ON” set, you can see the station ID and program title displayed on
TV.
To exit, press PROG.
(Continued)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Settings Using On-Screen Display (continued)
Setting the Clock
Press ENTER to start the “AUTO” clock
set feature.
After a while, the VCR automatically updates
the clock using the data broadcast by the
local TV stations.
8
Example: To set the clock to 2:30 p.m. on
August 25 (summer time) 2000.
Press PROG..
The MENU screen appears on the TV.
1
The following screen will appear on TV
depending on the broadcast at your location.
Select “PRESET” using FF or REW, and
press ENTER.
2
SET UP
PRESET
PROGRAM
CL
O
CK SET
SUMMER T I
T I
M
E
SET UP
PRESET
PROGRAM
M
E
ZOnE CH
AUTO AUTO
I
n
AUTOEASTERn AUTO
2
T I
M
E
DATE YEAR
CL
CH
O
CK SET
9
:
57A
M
1 / 01 ’ 00 SA
M
EMORY
PROG
En
D:
ENTER
CABLE BOX / DSS
GU I DE CH
Select the options using FF or REW.
Change the data using PLAY/x2 or
STOP.
1) Set “SUMMER TIME (Daylight-
Saving Time)”.
9
PROG
E
n
D:
ENTER
Press ENTER to select “CLOCK SET”.
3
4
SET UP
PRESET
PROGRAM
CL
IN, daylight-saving time begins on the first
Sunday in April. Because the clock
automatically changes from 2:00 AM to
3:00 AM (forward one hour), remember
that any part of a scheduled Timer
Recording that falls between these two
times will not be recorded.
OUT, daylight-saving time ends on the last
Sunday in October. The VCR clock
automatically changes from 2:00 AM to
1:00 AM (back one hour). Therefore, it can
affect your recording length if one is set
for this time.
O
CK SET
SUMMER T I
T I DATE YEAR
UT 12 : 00A
M
E
M
E
MAnU
O
M
1 / 01 ’ 00 SA
PROG
nD:
E
Select “AUTO” or “MANU” using PLAY/
x2 or STOP.
AUTO: The VCR automatically sets or
adjusts the clock.
If you select “AUTO” mode, proceed to step 8.
MANU: You can set the clock manually.
If you select “MANU” mode, select “SUMMER
TIME” using FF. Set to “IN” or “OUT” for the
summer (daylight saving) time using PLAY/x2
or STOP. (For “IN” and “OUT” selections, see
the description in step 9.)
2) Set “Time Zone”.
If you select “AUTO” for your time zone,
the VCR sets the clock using the first
Coordinated Universal Time information it
finds. If the time is not correct, select
another time zone or use the “MANU”
option.
Move to the next using FF.
(To move back, press REW.)
5
6
3) Set “CH”.
If you don't know the clock data channel,
select “AUTO”. The VCR will scan
automatically to tune the channel carrying
the clock data.
Vary the digits to set the hour.
PLAY/x2: To increase.
STOP:
To decrease.
If AUTO CLOCK SET is unsuccessful, set the
time and date through the “MANU” clock set
menu selection.
Repeat steps 5 and 6 to set the minutes,
month, day, and the year (by the last two
digits).
7
Press PROG..
Now the clock starts.
10
11
Proceed to step 10 to start the clock.
Press PROG. to exit.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Storing Channels on the VCR
This section is required if you receive only normal TV or unscrambled cable channels, or use a cable box
between your TV and the VCR.
Incoming Antenna/Cable (CATV) Signals
The VCR scans through all receivable TV and CATV channels and stores only the active
ones in your area into the memory. Once the storing is finished, you can select a desired
channel using CH/TRK.
Preparation
• Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 11).
• Press I.SELECT so that the channel number will appear if “L1” or “L2” is displayed in the VCR display.
Incoming Antenna/Cable (CATV) Signals
Press PROG. to display the MENU screen.
1
1
4
7
2
5
8
0
3
6
Number
buttons
Select “PRESET” using FF or REW,
and press ENTER.
2
SET UP
PRESET
PROGRAM
9
100
100
I.SELECT
CL
CH
O
CK SET
M
EMORY
CABLE BOX / DSS
GU I DE CH
REW
FF
PLAY/x2
REW
FF
PROG
En
D:
ENTER
PLAY/x2,
STOP
STOP
Select “CH MEMORY” using PLAY/
x2 or STOP, and press ENTER.
3
ENTER
SET UP
PRESET
CATV
PROGRAM
TV / CATV
AUTO SCA
ADD CH
TV
OFF
n
O
n
1, 6
––CH
––CH
ERASE CH
PROG
EnD:
Set “TV/CATV“ to “TV” or “CATV” using FF or REW.
TV: To store channels received via the antenna.
CATV: To store channels received via the incoming cable.
4
5
Select “AUTO SCAN” using PLAY/x2
or STOP, and press FF to set to
“ON”.
SET UP
PRESET
PROGRAM
TV
AUTO SCA
n
2CH
On
The VCR starts scanning and the
channels are stored in the VCR in
ascending order. When the scanning is
finished, the screen automatically
returns.
PROG
EnD:
Press PROG. to exit.
6
(Continued)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Channels on the VCR (continued)
3) Enter a channel number of 1 to 125 using
Adding or erasing channels
number buttons.
For more than 100 number, first press 100.
For CATV channels, refer to the chart below.
(For other orders, check with your cable
company.)
Adding channels
If a desired channel cannot be scanned
automatically because of a weak signal, it can be
added to the memory.
Erasing channels
You can erase a stored channel from the memory
if it is unnecessary.
4) Repeat steps 2) and 3) to add or erase
channels as necessary.
5) Press PROG. to exit.
1) Follow steps 1 to 3 of “Incoming Antenna/CATV
Signals”.
Selecting stored channels
2) Select “ADD CH” or “ERASE CH” using PLAY/X2
Once the active channels have been stored, you
can select the channels in two ways below.
Number buttons
To enter digits of the channel number.
• For one-digit number, enter 0 before.
• For more than 100 number, first press 100.
• Each number button needs to be pressed
within 2 seconds.
or STOP.
To add channels
SET UP
PRESET
PROGRAM
TV / CATV
AUTO SCA
ADD CH
TV
OFF
CATV
n
O
n
––On
––On
ERASE CH
TO SET CH
PUSH 0~9 KEYS
PROG
EnD:
CH/TRK
To shift up or down the stored channel numbers.
To erase channels
SET UP
PRESET
PROGRAM
TV / CATV
AUTO SCA
ADD CH
TV
CATV
n
OFF
O
n
––On
––On
ERASE CH
TO SET CH
PUSH 0~9 KEYS
PROG
EnD:
Channel reference chart
1
–
1(A-8)
2
2
2
3
3
3
4
4
4
5
5
6
6
7
7
7
8
8
8
9
9
9
Number on the VCR
TV
Corresponding channel number
5(A-7) 6(A-6)
CATV STD (HRC/IRC)
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
10 11 12 13
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
R
S
T
U
V
W
AA BB CC DD EE FF GG HH II
JJ KK LL MM NN OO
…
…
…
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69
PP QQ RR SS TT UU VV WW XX YY ZZ AAA BBB 65 66 67 68 69 70 71
–
–
…
…
…
93 94 95 96 97 98 99 100 101 102 103
121 122 123 124 125
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
93 94 A-5 A-4 A-3 A-2 A-1 100 101 102 103
121 122 123 124 125
CATV signals
• STD (standard) cable TV signals
• HRC (Harmonic Related Carriers) cable TV signals
• IRC (Incremental Related Carriers) cable TV signals
IRC is also called ICC (Incremental Coherent Carriers)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Video Cassette Use
Video Cassette Use
Loading a cassette
Push the cassette into the cassette compartment with the window side facing up and the
label side towards the front. The VCR is automatically turned on. The
appear in the VCR display.
indicator will
Ejecting a cassette
Press EJECT. The cassette is ejected from the cassette compartment.
Warning
Do not insert your hands or any foreign objects into the compartment. This may result
in injury or damage. Take special care with children to avoid accidents.
Precautions when using video cassettes
Video cassettes have a safety tab to prevent accidental erasure. If the tab has already been removed,
recording cannot be performed.
To prevent accidental erasure
To record again
Remove this safety tab with a screwdriver.
Cover the tab hole with adhesive tape.
• Avoid exposing cassettes to direct sunlight. Keep them away from heaters.
Avoid extreme humidity, vibrations or shock, strong magnetic fields (near a motor, transformer or
magnet) and dusty place.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Playback
This section explains the basic playback operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Press VCR to set the remote control operating the VCR.
Basic Playback
VCR
1
4
7
2
5
8
0
3
6
CH/TRK
Load a recorded cassette.
1
POWER
9
Power is turned on.
100
If the cassette has no safety tab,
playback starts automatically.
PLAY/x2
2
FF
Press PLAY/x2 to start playback.
2
3
POWER
REW
FF
S
P
VCR
DT
STOP
3
REW
µ
19
To stop playback, press STOP.
Rewinding / Fast-forwarding
Press REW or FF in the stop mode.
Adjusting the tracking
19µ HEAD
When playback starts, the VCR
automatically adjusts the tracking for clear
pictures and sound (Digital Auto Tracking).
You can view high quality pictures while
playing back a tape recorded in the SLP tape
speed.
By pressing 19µ repeatedly, the 19µ HEAD
mode is displayed on the TV screen as
follows:
The “DT” indicator blinks during the
adjusting.
If the VCR cannot locate the best possible
tracking point, hold down one of CH/TRK to
adjust the tracking manually.
• To resume the digital auto tracking, hold
down both CHANNEL on the VCR
simultaneously for about 2 seconds.
19U-HEAD AUTO: Usually set to “AUTO”. As
the playback starts, the VCR automatically
activates the 19µ head and reproduces high
quality pictures.
19U-(Continued)HEAD OFF: Set to “OFF” if
the pictures are marred by dots.
Notes
• During the adjusting, the playback picture and
sound may be distorted.
• The digital auto tracking is activated only in the
playback mode.
• To reset the manual tracking point to the center,
press both CHANNEL on the VCR
simultaneously for not longer than 1 second.
• The noise on the screen may not be completely
eliminated depending on the tape used,
especially when the tape was recorded on
another VCR.
Note
During playback with the 19µ head, momentary
noises or shakes may be produced when you
change the mode to the picture search or
variable speed playback.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Variable Speed Playback
You can play back a tape at various tape speeds.
Picture Search
1
4
7
2
5
8
0
3
6
A tape runs at 5 times or 7 times the normal playback speed so
that you can quickly locate a particular scene.
9
100
Press FF or REW during playback.
The tape runs at 5 times the normal playback speed.
1
PLAY/x2
REW
PLAY/x2
To change the tape speed to 7 times the normal playback
speed, press and hold FF or REW.
2
REW
FF
FF
STOP
If you release it, the tape speed returns to 5 times.
PAUSE/STILL
Note
SLOW
If you press FF or REW during picture search, the mode changes to fast-
forwarding or rewinding.
To resume normal playback
Press PLAY/x2.
Still Picture
Slow-motion Picture
A picture freezes so that you can watch
closer.
The tape runs at 1/7th or 1/15th the normal
playback speed.
Press PAUSE/STILL during playback.
The picture freezes.
Press SLOW during playback.
The tape runs at about 1/7th the normal
playback speed.
1
1
To resume normal playback
Each time you press SLOW, the speed
alternates between 1/7th and 1/15th.
Press PAUSE/STILL.
Notes
To resume normal playback
Press PLAY/x2.
• The still mode is automatically cancelled after
about 5 minutes and returns to normal playback.
• The still picture may shake if a picture of a fast-
moving object or scene is frozen. This is not a
defect in the unit.
Notes
• The slow-motion picture mode is automatically
cancelled after about 5 minutes and returns to
normal playback.
• The slow-motion picture may flicker up and down.
This is not a defect in the unit.
Adjusting Still Picture Stability
If the still picture is distorted or flickers, hold
down one of CH/TRK until the picture becomes
stable.
Adjusting the Tracking Manually
If the slow-motion picture is noisy, hold down one
Note
of CH/TRK until the best picture is obtained.
The distortion of the still picture may not be
eliminated completely.
Note
The noise in the slow-motion picture may not be
eliminated completely.
Note
When playing back a tape which is recorded in S-VHS format, distortion may occur during the variable speed
playback.
(Continued)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Variable Speed Playback (continued)
Frame Advance
Double Speed Playback
A picture advances frame by frame.
A tape runs at twice the normal speed.
Press PLAY/x2 during still playback.
Each time you press PLAY/x2, the picture
advances one frame.
Press PLAY/x2 during playback.
The picture runs at twice the normal playback
speed.
1
1
If you press and hold PLAY/x2, the tape runs
at 1/30th the normal playback speed.
To resume normal playback
Press PLAY/x2.
To resume normal playback
Press PAUSE/STILL.
Shuttle Dial Operation
You can also activate the picture search and slow playback at
various speeds by turning the shuttle dial on the VCR.
Turn the shuttle dial on the VCR.
1
Initial mode of tape operation
Stop
o
r
Playback
Still
The playback speeds differ depending on the recording tape speed of
the tape as follows.
Picture search
x5 x7
x15 x21
Reverse playback
SP:
SLP:
-x1
-x3
Notes
• The still picture mode will be released automatically after about 5 minutes
and forward playback will start.
• Fast-forwarding or rewinding started from the stop mode continues even if
the shuttle dial is released. To stop, press STOP.
• The reverse playback mode will be released automatically after about 25
seconds and forward playback will start.
• Noise bar may appear in reverse playback.
Note
If you playback a tape recorded in the SLP tape speed or a tape recorded on another VCR in various speed
mode, the picture may be noisy or monochrome.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Useful Functions in Tape Operation
These functions will help your playback.
S-VHS Quasi Playback (SQPB)
• This VCR can also play back a tape which is recorded in S-VHS format.
But the playback picture does not have the same quality and resolution as
the original S-VHS playback picture.
• This VCR cannot record in S-VHS format.
* SQPB is an abbreviation for S-VHS Quasi Playback.
Counter Function
1
4
7
2
5
8
0
3
6
You can view the clock, linear time counter or tape remaining
time in the VCR display or on the TV screen.
REMAIN/
COUNTER
9
100
COUNT RESET
DISPLAY
PLAY/x2
Each time you press REMAIN/COUNTER, the VCR display
changes in sequence as follows:
1
PLAY/x2
→ Linear time counter (HMS) → Tape remaining time (REMAIN/RT) → Clock
REW
FF
STOP
STOP
The indication above will also appear on the TV screen by pressing
DISPLAY.They are switchable with REMAIN/COUNTER.
ENTER
To reset the linear time counter to “0H00M00S”
PROG.
The counter is automatically reset to “0H00M00S” when a cassette is
ejected. If you want to reset at another point, such as the beginning of a
new recording, just press COUNT RESET.
Notes
• The linear time counter does not work on non-recorded portions on the tape.
• When the tape is ejected or the VCR is turned off, the display changes to
clock.
• If the tape rewinds back over “0H00M00S”, “–” appears in the VCR display.
• The displayed time of the linear time counter is only an approximation.
Tape Remaining Time
To view the tape remaining time in the VCR display, select the
tape length beforehand.
Turn on the VCR and load a cassette.
1
Press PROG. to display the MENU screen.
2
Select “SET UP” using FF or REW, and press ENTER.
3
Select the length of the tape.
4
SET UP
n
GTH
PRESET
PROGRAM
T120: for a T-120 tape or shorter
T160: for a T-140 or T-160 tape
T180: for a T-180 tape
TAPE LE
SAP SET
120 160 180
On
OFF
OFF
S IMULCAST
ANTEnn
LA GUAGE
DS FO
O
n
A
AUTO
MA U
n
n
EnG FRA ESP
X
I
n
O
n
OFF
PROG
nD:
E
(Continued)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Functions in Tape Operation (continued)
Press PROG. to exit.
5
Press REMAIN/COUNTER.
The remaining time (“RT - : - -”) appears in the VCR display.
6
Notes
• The displayed remaining time is an approximation.
• The remaining time is calculated according to the tape speed (SP or SLP)
and the cassette type.
Index Search Function
1
4
7
2
5
8
0
3
6
The VCR can find a point where a registered index signal is on a
tape and play back for about 5 seconds. You can easily locate
the desired program by inputting the index signal.
9
100
PLAY/x2
3
2
REW
FF
STOP
2
1
1
2
Index search
Playback
for 5 sec.
Playback
for 5 sec.
Playback
for 5 sec.
Playback
for 5 sec.
Registering index signals
Each time a recording starts, an index signal is automatically registered.
To register it somewhere else, press INDEX f during recording.
Note
A certain interval is required between the index signals: more than 1 minute in
the SP tape speed and more than 3 minutes in the SLP tape speed.
Index search
Load a cassette with the index signals registered.
1
Press INDEX in the stop or playback mode.
2
g
INDEX: To search in the reverse
direction.
0
H
00 00S
M
INDEX
f: To search in the forward
direction.
The VCR fast-forwards or rewinds the
tape. When an index signal is found, the
VCR plays back the tape for about 5
seconds, and then resumes fast-
I NDEX MARK
forwarding or rewinding. This is repeated
each time at an index signal.
Press PLAY/x2 when the desired program is found.
Normal playback starts.
3
Notes
• At the very beginning of the tape, the index search may not work properly.
• If you registered the index signals on a tape recorded on another VCR, the
recording may be blurred at the index point and the index search may not
work properly.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• If you record cable channels via the cable box, finish the cable box set-up (pages 33-36), and turn on the
cable box.
Basic Recording
Load a cassette with the safety tab attached.
1
1
4
7
2
5
8
0
3
6
Press TV/VCR so that the “VCR”
indicator appears in the VCR display.
POWER
SP
2
3
VCR
9
CH
100
2
5
4
Select a channel to record with
CHANNEL on the VCR, or CH/TRK
or number buttons on the remote
control.
If you see “L1” or “L2” in the VCR display, press I.SELECT so that the
channel number appears.
3
POWER
SP
PLAY/x2
VCR
REW
FF
STOP
6
I.SELECT
• If you record cable channels via the cable box, make the output
channel number of the cable box or “L1” appear, depending on your
connection. (See pages 11 – 13.)
Press SP/SLP to select the
recording tape speed.
4
POWER
SLP
VCR
CH
SP: Suitable for general recording with
better picture and sound quality.
SLP: Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
To record from other
connected equipment
In step 3, press I.SELECT to
switch the display as follows:
LI: To record via the LINE IN
1 jacks on the rear panel.
L2: To record via the LINE IN
2 jacks on the front panel.
REC
TIMER
Press REC on the VCR, or
simultaneously press both REC on
the remote control.
5
6
POWER
SLP
REC
VCR
CH
Recording starts.
Press STOP to stop recording.
Watching a TV program while
recording another
Recording off time setting
By setting the recording off time, the recording
stops and the VCR is turned off automatically.
1) While recording, press TV/VCR to turn off
“VCR” indicator.
While recording, press REC on the VCR
2) Choose another channel using the channel
repeatedly to set the desired off time.
selector on the TV.
Each time you press REC, each half-hour up to
about 4 hours later and “- : - -” appear cyclically.
Skipping unnecessary scenes while
recording
PM
POWER
OFF
SLP
VCR
REC
CH
Press PAUSE/STILL to stop recording
momentarily. To resume recording, press
PAUSE/STILL again.
Notes
• To cancel the recording in progress, press STOP.
• If the VCR clock is not set, this function will not
activate.
Note
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Timer Program Recording
The programmable timer allows you to record up to 6 different programs over one month.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Make sure that the clock is set correctly (page 16).
• Store the channels on the VCR (pages 17 and 18).
• If you record cable channels, finish the cable box set-up (pages 33 – 36), and turn on the cable box.
• If you record satellite channels, finish the DSS® satellite receiver set-up (pages 37 – 40), and turn on the
DSS® satellite receiver.
Timer Programming Procedure
Example: To record cable channel 25 in the SP tape speed from
9:30 p.m. until 10:00 p.m. on August 30. Today is August 25.
Load a cassette with the safety tab attached.
1
1
4
7
2
5
8
0
3
6
Press PROG. to display the MENU screen.
2
3
4
9
100
Select “PROGRAM” using FF or
REW, and press ENTER.
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
10
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
E D:
n
–
–
–
–
–
–
REW
FF
PLAY/x2
REW
FF
PLAY/x2,
STOP
STOP
ENTER
Move to the next using FF, and enter
the channel number 25 by using
PLAY/x2, STOP or number
buttons.
4
CANCEL
SET UP
On
PRESET
OFF SPD
PROGRAM
CH DATE
25 – / –– – : –– – : –
–
SLP
2, 9
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–
–
–
–
–
–
–– – / –– – : –– – : –
PROG
EnD:
• To record a cable program from the connected cable box:
Enter the cable channel number by number buttons, PLAY/x2 or
STOP.
If your cable box is not remote-controllable, choose the desired
channel (1 to 125) on the cable box.
• To record a satellite program from the connected DSS® satellite
receiver:
Enter the satellite channel number (100 to 999) by number
buttons, PLAY/x2 or STOP. (If a number 1 to 99 is entered, the
VCR will record a TV/CATV program on the channel, not a
satellite’s.)
If your DSS® satellite receiver is not remote-controllable, choose the
desired channel (100 to 999) on the DSS® satellite receiver.
To make corrections:
Press REW to move back to the item, or FF to forward.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Move to the next using FF, and set
the recording date using PLAY/x2 or
STOP.
5
SET UP
PRESET
OFF SPD
PROGRAM
CH DATE
O
n
SLP
25 8 30 – : –– – : ––
/
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
nD:
–
–
–
–
–
The date changes as follows:
…
…
→ 8/25 → 8/26 →
→ 9/24 → WKLYSU →
E
MO~FR ← WKLYSA ←
…
[WKLYSU] [WKLYSA]: You can record TV programs on the same
channel on the day and time every week.
[MO~FR]: You can record TV programs on the same channel on the
day and time Monday through Friday.
Move to the next using FF, and set
the hour and minutes of the
recording start time.
6
7
8
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
P
SLP
25 8
/
30 9
:
30 M – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
E D:
n
–
–
–
–
–
Move to the next, and set the
recording off time.
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
P
P
SLP
25 8
/
30 9
:
30 M 10 : 00
M
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
E D:
n
–
–
–
–
–
Move to the next, and select the tape
speed (SP) using PLAY/x2 or STOP.
For the tape speed “AUTO (Auto Speed
Select)”, see below.
To set another program, press FF, and
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
P
P
SP
25 8
/
30 9
:
30 M 10 : 00
M
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
D:
–
–
–
–
–
select the next line pressing STOP.
En
Repeat steps 4 to 8.
Press PROG..
Now programming is completed.
9
REC
TIMER
Press both TIMER simultaneously.
The power turns off and the VCR enters
the timer standby mode.
10
POWER
TIMER
Notes
Auto Speed Select
• Make sure that the tape length is selected correctly
according to the tape used on the SET UP screen
(page 23).
• When the SLP tape speed is selected and the tape
length is not sufficient to record the program to the
end, the program cannot be recorded to the end.
• The picture will be distorted when playing the part
where the recording tape speed is switched from
If you are not sure the tape is long enough for
timer program recording in the SP tape speed,
set the recording tape speed to “AUTO”.
Recording starts in the SP tape speed and the
VCR automatically selects the tape speed to
record the program to the end. If the tape length
is not long enough, the tape speed automatically
changes from SP to SLP.
SP to SLP with the Auto Speed Select feature.
(Continued)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Program Recording (continued)
Confirming the timer programs
(in the timer standby mode)
If a power failure occurs during the
timer program recording (including
VCR Plus+ C3 ® system recording
(page 31))
Press PROG..
The screen for confirming will appear.
• When a power failure has occurred, “- -:- -”
appears in the VCR display. Since the
programmed contents have been cleared,
reset the clock and timer programming.
• When power has failed for a short time, the
colon of the current time display blinks. The
programmed contents are not affected. Reset
the clock.
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
P
P
SP
25 8
/
30 9
:
30 M 10 : 00
M
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
nD:
–
–
–
–
–
E
After about 30 seconds, the screen disappears.
Overlaps of the programs
Changing/cancelling the timer
programs
If two timer programs overlap, the recording start
time of program 2 has priority over the recording
off time of program 1.
1) If the TIMER indicator is lit, press both TIMER
to turn it off, and then turn the VCR on by
pressing POWER.
Overlapped portion (not recorded)
Program 1
(Start time)
Program 2
2) With steps 2 to 9, change the items.
To cancel a program, select the program you
want to cancel in step 4, and press CANCEL.
The line is then cleared.
(Start time)
3) Press both TIMER to return to the timer
standby mode.
Recording or playback in the timer
standby mode
First press both TIMER to release the timer
standby mode, and then press POWER to turn
on the VCR. The VCR will be available for use.
• Be sure to press both TIMER again to return
the VCR to the timer standby mode after you
are finished.
Error indication
The “E” (Error) indicator appears in the VCR
display if you press both TIMER when:
–– a cassette is not loaded.
–– the loaded cassette has no safety tab.
–– no timer program is set.
In these cases, a recording can not be made.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
3
®
VCR Plus+ C system Set-up
VCR Plus+ C3 ® system is a timer recording system for an easier programming that requires you only to
enter a PlusCode® programming number assigned to a desired program. This section explains the
necessary set-up to make VCR Plus+ C3 ® system recordings.
Sample of a Guide channel chart from a local TV listing
The flow chart below will give you an idea
as to what must be done to use the VCR
VCR Plus+® SYSTEM CHANNEL NUMBERS
Plus+ C3 ® system feature.
Broadcast
channels
Assigned
channels
Cable
Assigned
channels channels
A & E........................39
AMC.........................35
(
)
3
6
KCRA NBC .................3
Setting the Clock (page 16)
(
)
KVIE PBS ...................6
(
)
)
10 KXTV CBS ................10
BET..........................57
BRAV....................... 54
CMTV.......................14
CNBC.......................23
CNN......................... 42
↓
(
13 KOVR ABC ...............13
(
)
19 KCSO SPAN .............19
Cable Box Set-up (page 33)
(
)
31 KRBK IND .................31
(FOX)
(IND)
(IND)
40 KTXL
58 KSCH
44 KBHK
24 KCPM
................40
................ 25
.................15
...............24
...............28
.................27
.................28
↓
-
C SPAN....................28
CUNY.......................29
DIS...........................53
ESPN....................... 34
FAM......................... 47
HBO......................... 33
Storing Channels on the VCR
(NBC)
(NBC)
KRNV
(IND)
(ABC)
KGO
4
(page 17)
42 KFCB
7
↓
VCR Plus+ C3 ® system Set-up
↓
Sample of a Channel line-up chart from a cable-TV
company
VCR Plus+ C3 ® system Recording
(page 31)
CHANNEL LINE-UP CHART
* With the VCR Plus+ C3 ® system, this video
cassette recorder can automatically select the
appropriate channel on your compatible cable
box or satellite receiver. VCR Plus+, C3 and
PlusCode are registered trademarks of
Gemstar Development Corporation. The VCR
Plus+ system is manufactured under license
from Gemstar Development Corporation.
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
ME/U
8 WISH
4 WTTV
6 WRTV
VCA/Local origination
HOME BOX OFFICE
A.P News Plus
9 WGN.
You must give the VCR the special
numbers for guide channels (also called
VCR Plus+® system channel numbers)
assigned to each channel that you receive
in your home. The VCR identifies the
channel to be recorded by the guide
channel number you enter.
The guide channel numbers are published
in TV guide magazine, selected local TV
publications, or the channel guide from
cable company. If you cannot find the
numbers, call Gemstar’s customer service
department at 1-800-4321-VCR.
(Continued)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Plus+ C3 system Set-up (continued)
®
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• If you record cable channels, finish the cable box set-up (pages 33 – 36).
• Prepare the list like below.
Example
Your home channel number (on the channel line-up
chart supplied by cable companies)
Guide channel number
(on the TV Guide, local TV listings etc.)
Station
HBO
ESPN
AMC
33
34
35
7
Guide Channel Setting
Press PROG..
1
2
3
4
5
6
1
4
7
2
5
8
0
3
6
7
Select “PRESET” using FF or REW, and press ENTER.
Select “CH MEMORY”using PLAY/x2 or STOP, and press ENTER.
Set “TV/CATV” to “TV” or “CATV” using FF or REW.
Press PROG. to return to the PRESET screen.
Select “GUIDE CH” using PLAY/x2
9
100
2,4
PLAY/x2
REW
FF
STOP
3,6,7
ENTER
SET UP
PRESET
PROGRAM
GU IDE CH
125
H
OME CH
or STOP, and press ENTER.
125
1
1
2
3
(the case of CATV mode)
2
3
GU I DE CH
HOME CH
1,5,8
T
E
O
SET
CH PUSH 0~9 KEYS
PROG
nD:
Enter channel numbers on the right of the guide channel
numbers.
7
Find a guide number you marked on the list using PLAY/x2 or STOP,
and enter the corresponding home channel number if necessary by
using number buttons.
Example: To enter home channel number
7 (HBO) with guide channel number 33
assigned.
SET UP
PRESET
PROGRAM
GU IDE CH
30
HOME CH
30
31
32
7
31
32
33
GU I DE CH
HOME CH
SET
CH PUSH 0~9 KEYS
In some areas, one channel may be
assigned more than one guide channel
number. In this case, enter the home
channel number to each of the guide
channel numbers.
T
E
O
nD:
PROG
Notes
• When your cable company
changes the channel line-
up, you must re-do this set-
up for the channel.
Press PROG. to exit.
The set-up is all over and your VCR Plus+ C3 ® system recording is
now available.
8
• The VCR Plus+ C3 ® system
feature does not work on
programs from a connected
DSS® satellite receiver.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
3
®
VCR Plus+ C system Recording
After performing the VCR Plus+ C3 ® system set-up, you can easily program a recording simply by
entering the PlusCode® programming number. The numbers are published in the TV listings of
newspapers, TV guide magazine, etc.
Preparation
• Make sure that the clock is set correctly (page 16).
• Load a cassette with a safety tab.
For cable box users:
• Finish the cable box set-up (pages 33 – 36), and turn on the cable box.
For DSS® satellite receiver users:
• This VCR cannot record satellite programs with the VCR Plus+ C3 ® system feature. To make an unattended
recording of satellite programs, see “Timer Program Recording” (pages 26 – 28).
Sample of TV program listing in a TV guide magazine
5PM
FAM
HBO
POPEYE
725692
Cartoon
237945
MAKING OF A CHAMPION
A look at gymnast and Olympic hopeful Kim
Zmeskal from novice to seasoned competitor.
PlusCode®
programming
number
N I K
HEY DUDE
Children 793571
One of Ted’s teachers stays at the ranch.
USA
TBS
MY TWO DADS
GOOD TIMES
586858
2261858
Comedy
Comedy
5:35
VCR Plus+ C3 ® system Programming
Press VCR Plus+.
The VCR Plus+ screen appears.
1
1
4
7
2
5
8
0
3
6
2
9
Enter a PlusCode® programming number.
Example: To record a program with the
PlusCode® programming number 36295
(fictitious code).
2
100
SET UP
PRESET
PROGRAM
7
VCR PLUS+
PLUSCODE
MODE
REW
FF
36295
–
PLAY/x2
O
nCE MO~FR WKLY
Press number button 3, 6, 2, 9 and 5.
SPEED
SLP AUT
O
SP
REW
FF
Confirm that the number is entered
correctly.
To correct a mistake, press CANCEL and
E
TO S
T
PLUSCODE
PLAY/x2,
STOP
PROG.
STOP
PUSH 0~9 KEYS
ENTER
PROG
EnD:
enter the correct number.
5
Select “MODE” using PLAY/x2 or
STOP, and set the recording
frequency.
OnCE: To record once.
DAILY(MO~FR):To record programs on
the same channel at the same time
Monday through Friday.
CANCEL
3
SET UP
PRESET
PROGRAM
1
VCR PLUS+
PLUSCODE
MODE
36295
O
nCE MO~FR WKLY
SPEED
SLP AUT
O
SP
ENTER
PROG
EnD:
WEEKLY: To record programs on the
same channel at the same time on the
same day every week.
Select “SPEED” using PLAY/x2 or
STOP, and set the recording tape
speed.
4
SET UP
PRESET
PROGRAM
VCR PLUS+
PLUSCODE
MODE
36295
O
nCE MO~FR WKLY
SPEED
SLP AUT
O
SP
For AUTO speed, see page 27.
ENTER
PROG
EnD:
(Continued)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Plus+ C3 system Recording (continued)
®
Press ENTER.
The program setting is now memorized.
5
SET UP
PRESET
PROGRAM
CH DATE
O
n
OFF SPD
P
P
SLP
25 8
/
30 9
:
30 M 10 : 00
M
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
–– – / –– – : –– – : ––
PROG
nD:
–
–
–
–
–
• If your cable box is not remote-
controllable, select the recording
channel on the cable box beforehand.
E
To set another program, repeat steps 1 to 5.
6
REC
TIMER
To finish press the two TIMER
buttons simultaneously.
The VCR enters the timer standby mode.
7
POWER
TIMER
Confirming the VCR Plus+ C3 ® system
timer programs
Recording or playback in the timer
standby mode
Before the VCR enters the timer standby
mode (TIMER indicator not lit)
1) Press PROG. to display the MENU screen.
2) Press ENTER to select “PROGRAM”.
Check the programmed data.
First press both TIMER to release the timer
standby mode, and then press POWER to turn
on the VCR. The VCR will be available for use.
• Be sure to press both TIMER again to return
the VCR to the timer standby mode after you
have finished.
3) Press PROG. to exit.
During the timer standby mode (TIMER
indicator lit)
Press PROG..
The screen for confirming appears.
After about 30 seconds, the screen disappears.
Error indications
If “FULL / CANCEL PROG?” message appears
on the TV during programming, no more
programs can be entered. If you want to add
another, delete one existing program on the
screen by using PLAY/x2 or STOP.
If an incorrect PlusCode® programming number is
entered, “ERROR CODE ENTERED” appears on
the screen. Press CANCEL to clear the number
and enter correct one.
Canceling the VCR Plus+ C3 ® system
timer programs
1) If the TIMER indicator is lit, press both TIMER
to turn it off, and turn on the VCR by pressing
POWER.
2) Press PROG. to display the MENU screen.
3) Press ENTER to select “PROGRAM”.
4) Select a program which you want to cancel.
If “CLASH” message appears on the TV during
programming, it tells you that two programs with
the same recording start time have been entered.
Correct either of the two programs as follows:
1) Select the number of the program to correct by
5) Press CANCEL.
using PLAY/x2 or STOP.
The line is cleared out.
2) Correct the data, or clear out the line by
pressing CANCEL and then press
VCR Plus+ to enter a PlusCode® programming
number.
6) Press PROG. to exit.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Cable Box Set-up
The VCR can directly control channel selecting of the connected cable box.
Cable Box Control
Connection Type
Type A
This VCR needs to be connected to a cable
box equipped with an infrared wireless
remote control. You can select cable
channels from the cable box by operating
this VCR.
It is also possible to automatically change
the cable channels according to your
program setting in the timer program
3
®
recording or VCR Plus+ C system recording.
Placing the Cable Box
Put the cable box on the top of the VCR as
shown below. Do not block the sensor
window.
Cable box
Type B
Wall
Front of the VCR
Sensor window
The infrared signals come out of the sensor
window and the front of the VCR. Then they
bounce off walls and other objects in the
room and are received by the cable box.
The VCR sends out infrared signals to your
cable box even during timer program
recording or VCR Plus+ C3 ® system
recording.
Type C
A
A/B switch
A
B
B
Cable box
Notes
• If the channels cannot be controlled properly
because the infrared signal fails to reach the cable
box, change the position of the box on the VCR so
that it can receive the signal.
• Keep the cable box turned on even while the VCR
is in the timer program recording or VCR Plus+ C3 ®
system recording.
Type D
Cable box
(Continued)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Box Set-up (continued)
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Set “TV/CATV” on the CH MEMORY screen to “CATV” (page 17).
Cable Box Set-up
Press PROG. to display the MENU screen.
1
2
3
1
4
7
2
5
8
0
3
6
Number
buttons
Select “PRESET” using FF or REW, and press ENTER.
9
100
Select “CABLE BOX/DSS” using PLAY/x2 or STOP, and press
ENTER.
100
I.SELECT
REW
FF
PLAY/x2
Select “NO” or “C.BOX” using FF or REW according to your
connection type.
4
REW
FF
PLAY/x2,
STOP
STOP
NO:
• Type A
• Type C (A/B switch “A”)
SET UP
PRESET
PROGRAM
USE
ENTER
• Cable channels will be selected using
CH/TRK on the remote control or
CHANNEL on the VCR.
nO C. BOX DSS
POWER
(CABLE BOX)
CH
→ Go to step 8.
C.BOX: • Type B
• Type C (A/B switch “B”)
• Type D
(CABLE BOX)
SET UP
PRESET
PROGRAM
PROG.
USE
OUTPUT CH
CO TROL
nO C.BOX DSS
CH
OFF
3
n
O
n
→ Go to step 5.
Select “OUTPUT CH” using PLAY/x2 or STOP, and enter
5
6
either of the following according to your connection.
(Example)
Type B, C: the output channel number of
your cable box using number buttons.
(Usually 3 or 4. Check the rear of the
cable box.)
SET UP
PRESET
PROGRAM
USE
OUTPUT CH
CO TROL
nO C. BOX DSS
CH
OFF
3
Type D: the line input mode “L1” using
n
O
n
I.SELECT.
Select “CONTROL” using PLAY/x2 or STOP, and set to “ON”
or “OFF” using FF or REW.
ON: if your cable box is remote-
controllable.
SET UP
PRESET
PROGRAM
USE
OUTPUT CH
CO TROL
BRA TYPE
nO C. BOX DSS
CH
• Cable channels will be selected by CH
(CABLE BOX) on the remote control.
The VCR can change the cable
channel to the desired one when timer
recording or VCR Plus+ C3 ® system
recording starts.
3
n
OFF
O
n
n
D
nO.
1
PROG
EnD:
→ Go to step 7.
OFF: if your cable box is NON remote-
controllable.
SET UP
PRESET
PROGRAM
• Cable channels will be selected by the
own channel selector of the cable box.
The VCR channel should be set to the
output channel of the cable box.
USE
OUTPUT CH
nO C. BOX DSS
CH
3
CO
n
TROL
PROG
OFF
O
n
→ Go to step 8.
EnD:
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Select “BRAND TYPE” using STOP, and enter a brand code
of your cable box using number buttons. Refer to the table
on the next page.
7
Example: For a TOSHIBA cable box, identified by number 36.
Cable box display
SET UP
PRESET
PROGRAM
VCR display
USE
OUTPUT CH
CO TROL
BRA TYPE
nO C. BOX DSS
3
CH
n
OFF
O
n
n
D
nO. 36
PROG
EnD:
Cable channel number
Make sure that the channel display of your cable box has changed to
9. If not, try each brand code assigned to the brand of your cable box
until the display changes to 9.
If it still holds;
• Relocate the cable box on the VCR.
• Use each of digits from 1 to 91.
Press PROG. to exit.
8
Notes
• If your cable channel does not change to 9 in step 7, the cable box will not
be able to change channels in the timer recording. In this case, set
“CONTROL” to “OFF” in step 6.
• The cable box control is not compatible with the DSS® satellite receiver
control.
Buttons to control a remote-
controllable cable box
Once you complete the set-up for a remote
controllable cable box, your cable box can be
controlled by the following buttons on the remote
control of the VCR.
• POWER (CABLE BOX)
To turn the cable box on or off.
• CH (CABLE BOX)
To select cable channels in the upper or lower
direction. (not applicable to some brands of
cable box.)
• Number buttons (0 – 9)
To select desired channels to record.
• 100
Some cable boxes require you to use this
button as the enter button. Press this button
after selecting the cable channel with number
buttons.
(Continued)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Box Set-up (continued)
Table of cable box brand codes
Brand name of your
Brand code
Brand name of your
cable box
Brand code
cable box
Telecaption
Teleview
Texscan
Tocom
77
Toshiba
Anvision
36
4, 6, 32, 42, 78
18, 19
1, 33, 34, 42, 48, 49, 73,
91
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
1, 20, 21, 29, 42, 44, 63,
88, 91
Archer
Unika
1, 20, 21, 29, 42, 44, 63,
88, 91
Cablestar
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
Universal
29, 42, 43, 44, 52, 63, 82,
88
7, 23, 45, 50, 84
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
6
Cableview
Citizen
Curtis
30, 42, 44, 52, 63, 88
30, 42, 44, 52, 63, 88
8, 9, 56, 61
1, 20, 21, 29, 42, 44, 63,
88, 91
Videoway
Viewstar
Diamond
Warner Amex
Zenith
Eagle
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
7, 23, 45, 50, 84
Eastern
GC Brand
Gemini
26, 28
30, 42, 44, 52, 63, 88
4, 30, 85
General Instrument 1, 2, 3, 4, 31, 34, 55, 85,
91
Hamlin
Hitachi
Jerrold
14, 15, 28, 41
31, 79, 80
1, 2, 3, 4, 31, 34, 55, 85,
91
Macom
31, 79, 80
Magnavox
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
29, 32, 38, 39, 42, 44, 88
29, 32, 38, 39, 42, 44, 88
10, 11, 12, 13, 46
10, 11, 12, 13, 46
6, 8, 16, 17
4, 13, 20, 21, 22, 23, 24,
25, 26, 58, 62, 84
5, 6, 78
Movietime
NSC
OAK
OAK Sigma
Panasonic
Philips
Pioneer
Pulsar
Randtek
30, 42, 44, 52, 63, 88
13, 20, 21, 22, 23, 24, 25,
26, 58, 62, 84
6, 8, 16, 17
RCA
Realistic
Regal
44, 88
14, 23, 41, 84
26, 28
29, 32, 38, 39, 42, 44, 88
4, 6, 32, 42, 78
8, 9, 56, 61
Regency
Rembrandt
Samsung
Scientific Atlanta
Sheritech
SL Mark
Sprucher
Stargate
27
4, 6, 32, 42, 78
6, 8, 16, 17
4, 6, 30, 32, 42, 44, 52, 63,
78, 88
Sylvania
Teknika
19
74
36
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
DSS® Satellite Receiver Set-up
The VCR can directly control channel selecting of the connected DSS® satellite receiver.
DSS® Satellite Receiver Control
This VCR needs to be connected to a DSS®
satellite receiver equipped with an infrared
wireless remote control. You can select
satellite channels from the DSS® satellite
receiver by operating this VCR.
Connection Type
Type A
Satellite
antenna
RF IN
RF OUT
DSS® is registered trademark of DIRECTV,
Inc., a unit of GM Hughes Electronics.
3CH
4CH
DSS® satellite receiver
RF IN
It is also possible to automatically change
the satellite channels according to your
program setting in the timer program
recording.
RF OUT
Placing the DSS® Satellite
Receiver
Type B
Put the DSS® satellite receiver on the top of
the VCR as shown below. Do not block the
sensor window.
Satellite
antenna
Incoming cable
DSS® satellite receiver
DSS® satellite receiver
3CH
4CH
Wall
LINE IN 1
Front of the VCR
Sensor window
The infrared signals come out of the sensor
window and the front of the VCR. Then they
bounce off walls and other objects in the
room and are received by the DSS® satellite
receiver. The VCR sends out infrared
signals to your DSS® satellite receiver even
during timer program recording.
LINE OUT
Notes
• If the channels cannot be controlled properly
because the infrared signal fails to reach the DSS®
satellite receiver, change the position of the
receiver on the VCR so that it can receive the
signal.
• Keep the DSS® satellite receiver turned on even
while the VCR is in the timer program recording.
(Continued)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
DSS® Satellite Receiver Set-up (continued)
Preparation
Select the video channel (3 or 4) or video input mode on the TV.
DSS® Satellite Receiver Set-up
Press PROG. to display the MENU screen.
1
2
1
4
7
2
5
8
0
3
6
Number
buttons
Select “PRESET” using FF or REW,
9
SET UP
PRESET
PROGRAM
and press ENTER.
100
I.SELECT
CL
O
CK SET
CH
ME
MORY
REW
FF
CABLE BOX /DSS
GU I DE CH
PLAY/x2
REW
FF
PROG
En
D:
ENTER
PLAY/x2,
STOP
STOP
Select “CABLE BOX/DSS” using
PLAY/x2 or STOP, and press
ENTER.
3
ENTER
SET UP
PRESET
PROGRAM
USE
POWER
(CABLE BOX)
nO C. BOX DSS
CH
(CABLE BOX)
PROG.
PROG
EnD:
Select “DSS” using FF.
4
5
SET UP
PRESET
PROGRAM
USE
OUTPUT CH
nO C. BOX DSS
CH
OFF
3
CO
n
TROL
PROG
O
n
E
nD:
Select “OUTPUT CH” using PLAY/x2 or STOP, and enter
either of the following according to your connection.
(Example)
Type A: the output channel number of
SET UP
PRESET
PROGRAM
your DSS® satellite receiver using
number buttons. (Usually 3 or 4. Check
USE
nO C. BOX DSS
CH
OUTPUT CH
CO TROL
the rear of the DSS® satellite receiver.)
3
n
OFF
O
n
Type B: the line input mode “L1” using
I.SELECT.
TO SET CH
PUSH 0~9 KEYS
PROG
EnD:
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Select “CONTROL” using PLAY/x2 or STOP, and set to “ON”
or “OFF” using FF or REW.
6
ON: if your DSS® satellite receiver is
remote-controllable.
SET UP
PRESET
PROGRAM
USE
OUTPUT CH
CO TROL
BRA TYPE
• Satellite channels will be selected by
CH (CABLE BOX) on the remote
control.
nO C. BOX DSS
CH
3
n
OFF
O
n
n
D
nO.
1
The VCR can change the satellite
channel to the desired one when timer
recording starts.
PROG
EnD:
→ Go to step 7.
OFF: if your DSS® satellite receiver is
NON remote-controllable.
SET UP
PRESET
PROGRAM
• Satellite channels will be selected by
the own channel selector of the DSS®
satellite receiver.
The VCR channel should be set to the
output channel of the DSS® satellite
receiver.
USE
OUTPUT CH
nO C. BOX DSS
CH
3
CO
n
TROL
PROG
OFF
O
n
EnD:
→ Go to step 8.
Select “BRAND TYPE” using STOP, and enter a brand code
of your DSS® satellite receiver using number buttons. Refer
to the table on the next page.
7
Example: For a TOSHIBA DSS® satellite receiver, identified by
number 99.
SET UP
PRESET
PROGRAM
VCR display
USE
OUTPUT CH
CO TROL
BRA TYPE
nO C. BOX DSS
3
CH
n
OFF
O
n
n
D
nO. 99
PROG
EnD:
Make sure that the background of the above display has changed to
the satellite program on channel 200. If not, relocate the DSS®
satellite receiver on the VCR so that it can receive the infrared signal.
Press PROG. to exit.
8
Notes
• If your satellite channel does not change to 200 in step 7, the DSS® satetllite
receiver will not be able to change channels in the timer recording. In this
case, set “CONTROL” to “OFF” in step 6.
• The VCR Plus+ C3 ® system recording is not available on satellite channels.
• The DSS® satellite receiver control is not compatible with the cable box
control.
(Continued)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
DSS® Satellite Receiver Set-up (continued)
Buttons to control a remote-
Table of DSS® satellite receiver brand
codes
controllable DSS® satellite receiver
Once you complete the set-up for a remote
controllable DSS® satellite receiver, your DSS®
satellite receiver can be controlled by the
following buttons on the remote control of the
VCR.
• POWER (CABLE BOX)
To turn the DSS® satellite receiver on or off.
• CH (CABLE BOX)
Brand name of your
Brand code
DSS® satellite receiver
TOSHIBA
RCA
99
98
97
SONY
To select satellite channels in the upper or
lower direction. (not applicable to some brands
of DSS® satellite receiver.)
• Number buttons (0 – 9)
To select desired channels to record.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
MTS Broadcast Compatibility
This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to
your stereo system or stereo TV, you will experience the SAP or stereo sound.
Preparation
Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
Recording the SAP/Stereo Broadcast
On the SET UP screen (page 15),
1
SET UP
n
GTH
PRESET
PROGRAM
1
4
7
2
5
8
0
3
6
select “SAP SET” using PLAY/x2 or
STOP, and set to “ON” using REW or
FF.
TAPE LE
SAP SET
120 160 180
On
OFF
OFF
9
S IMULCAST
ANTEnn
LA GUAGE
DS FO
O
n
A
AUTO
MA U
n
100
n
EnG FRA ESP
DISPLAY
X
I
n
O
n
OFF
PROG
nD:
E
PLAY/x2
REW
FF
1
1, 2
1
STOP
Press PROG. to exit.
2
3
Perform a recording.
SAP (Second Audio Program broadcast):
A separate audio program, usually broadcast in a second language with the
main language.
A.SELECT
Selecting a sound
Sounds recorded on the tape
According to your setting of “SAP SET” on the SET UP screen, the sound is recorded onto different
tracks of the tape as below. Set “SAP SET” to “ON” or “OFF” appropriately.
Contents of recorded sound
On-Screen Display
(Press DISPLAY.)
Setting of “SAP SET”
on the SET UP
screen
Type of receiving
broadcast
Hi-Fi sound track
Normal sound
track (Mono)
L
“SAP”
not lit
“STEREO”
R
Regular
(monaural audio)
“ON” or “OFF”
not lit
MONO
MONO
MONO
Stereo
“ON” or “OFF”
“ON”
not lit
lit
lit
not lit
not lit
lit
MONO (MIXED)
MONO
STEREO
MONO
MONO
MONO
SAP
MONO
SAP
Regular+SAP
“OFF”
lit
MONO
“ON”
lit
MONO
Stereo+SAP
“OFF”
lit
lit
MONO (MIXED)
STEREO
Sounds in playback
You can play SAP and/or stereo broadcasts with this VCR. Press A.SELECT to select a desired sound.
Desired sound
SAP sound
L , R indicators in the VCR display
R (right) is on.
Sound output
SAP
Stereo sound
Both R (right) and L (left) are on.
Stereo
Note
When the TV is connected to the RF OUT terminal of the VCR, the output sound is monaural.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Simulcast Recording
When TV program such as MTV, HBO or MAX is being simulcast in FM stereo in your area, the VCR can
also record the simulcast sound from an FM stereo tuner or receiver onto the Hi-Fi track and normal
track.
Preparation
• Connect the TV and stereo system to the VCR as below.
• Turn on the connected FM tuner and tune to the station for the simulcast program.
To the FM antenna terminal
Broadcast or
incoming cable
AUDIO OUT
AUDIO IN
AUDIO OUT
LINE IN 1 AUDIO
Simulcast Recording
On the SET UP screen (page 15),
1
SET UP
n
GTH
PRESET
PROGRAM
1
4
7
2
5
8
0
3
6
select “SIMULCAST” using PLAY/x2
or STOP, and set to “ON” using REW
or FF.
TAPE LE
SAP SET
120 160 180
3
On
OFF
OFF
S IMULCAST
ANTEnn
LA GUAGE
DS FO
9
O
n
A
AUTO
MA U
n
100
n
EnG FRA ESP
X
I
n
O
n
OFF
4
5
PROG
nD:
E
PLAY/x2
REW
FF
1
6
1
Press PROG. to exit.
2
3
STOP
Select the desired channel using CHANNEL on the VCR or
CH/TRK on the remote control.
If you use a cable box, select a desired channel on the box.
1, 2
Select the recording tape speed using SP/SLP.
Press REC to start recording.
4
5
6
Press STOP to stop recording.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Multi Brand Remote Control
The remote control can be compatible with various brands of TV by setting their control codes. The
TOSHIBA code has initially been set to control TOSHIBA TVs.
Setting Control Codes
1
Press TV to set the remote control operating your TV.
1
POWER
1
4
7
2
5
8
0
3
6
CH/TRK
While holding down PROG., enter
the two digits of your TV’s brand
code (listed on page 44) using
number buttons.
2
Hold down.
Example
9
PROG.
TV VOL
100
Number
buttons
100
0
2
PLAY/x2
Release PROG..
3
4
DISPLAY
REW
FF
STOP
Point the remote control at your TV and use each button listed
below to make sure that your TV is operated correctly.
I.SELECT
ENTER
POWER
CH/TRK
To turn the TV on or off.
To select TV channels in the upper or lower
direction.
2, 3
TV VOL
To adjust the sound level.
I.SELECT
To select an external source such as a VCR.
Number buttons To select TV channels. When selecting channels
1 to 9, first enter 0 and then the desired number.
100
DISPLAY
ENTER
To substitute for 100 channel key.
To turn on or off TV’s screen display.
To use for the TV’s ENTER key.
Important
Some TVs may not respond to all the operations above, or
may not be operated at all with this remote control. In this
case, operate your TV with its own remote control.
Notes
• For some brands, several control codes (brand codes) are allocated. Try
each of them until the buttons work on your TV.
• If you replace the remote control’s batteries, set the brand code again.
(Continued)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi Brand Remote Control (continued)
Table of Brand Codes
Brand name of your TV
Brand name of your TV
Brand Code
Brand Code
Toshiba
Bell & Howell
Carver
01
09
10
03
12
Proton
11
14
Pulser
Quasar
Radio Shack
RCA
07, 15
Celebrity
Citizen
13
02
Curtis Mathes
Dumont
Electro band
Emerson
Fisher
09, 12
Realistic
Runco (NEC)
Samsung
Sanyo
09, 11, 13
14
14
03
11, 12
09, 11
09
09
Scotch
11
GE
02, 07, 11
Scott
11
Gibralter
Goldstar
Hallmark
Hitachi
14
Sears
01, 02, 09, 10, 11
11
Sharp
08, 13
11
Sony
03
06
Soundesign
Supreme
Sylvania
Tandy
11
Infinity
10
03
JBL
10
10
JCB
03
08
JVC
05
Technics
Techwood
Teknika
TMK
07, 15
LXI
01, 02, 09, 10, 11
07
Magnavox
Marantz
Megatron
Memorex
MGA
10
04, 10, 12
10
11
06, 11
Victor
05
04, 09, 11
Vidikron
Vidtech
Wards
10
04, 11
11
Midland
Mitsubishi
Motorola
MTC
02, 07, 14
10, 11, 13
14
04, 11
Zenith
08
12
NAD
01, 11
Nikko
11
Optimus
Optonica
Panasonic
Penney
Philco
09
08
07, 10, 15
01, 02, 07, 11, 12
10
10
16
12
07
02
Philips
Pioneer
Princeclub
Prism
Proscan
44
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION
Before Calling Service Personnel
Check the following symptoms before requesting servicing.
No power.
The desired sound is not heard, such as
SAP, stereo, or regular sound.
• The power cord is not plugged in.
• Setting of sounds is not correct.
– Plug the power cord into the outlet firmly.
– Select a desired sound using A.SELECT.
(page 41)
Although the power is on, the VCR will
not work.
Noise is present in the Hi-Fi sound being
played.
• There is no cassette.
– Load a cassette. (page 19)
• Tracking is not set appropriately.
– Adjust the tracking manually. (page 20)
The clock does not work.
• There has been a power failure.
– Reset the clock. (page 16)
The timer recording function does not
work.
The timer does not work properly.
• There is an error in programming.
• The time is incorrect.
– Reset the timer recording program. (page 26)
– Set the clock correctly. (page 16)
• There is no cassette in the VCR.
– Load a cassette with the safety tab attached.
(page 19)
The picture does not appear on the TV
screen.
• The cassette does not have the safety tab.
– Use another cassette with a safety tab or
cover the hole with adhesive tape. (page 19)
• The video channel or video input mode is not
set correctly.
– Set the TV channel to the video channel (3 or
4) or set the video input mode on the TV.
(page 11)
• The timer indicator is not displayed.
– Press both TIMER simultaneously. (page 27)
• The TV signal is weak.
– Adjust the antenna direction or use an
optional antenna booster.
• There has been a power failure.
– Reset the clock. (page 16)
• The cable box set-up has not been set correctly.
– Make the set-up correctly. (page 34)
• The power cord is not plugged in.
– Plug the power cord into the outlet firmly.
• The cable box is not turned on.
– Turn on the cable box.
The picture does not appear on the TV
screen during recording and playback.
The VCR Plus+ C3 ® system recording
cannot be done.
• The video channel or VCR mode is not set
correctly.
– Press TV/VCR to select the VCR mode and
set the TV channel to 3 or 4. (pages 11, 25)
• The guide channel numbers are not set up
correctly.
– Make the guide channel number setting.
(page 29)
The VCR does not record.
• The loaded cassette has no safety tab.
– Use a cassette with a safety tab or cover the
hole with adhesive tape. (page 19)
• The cable box is not turned on when the
channel comes in the VCR via the cable box.
– Turn on the cable box.
The playback picture is poor.
• The cable box set-up has not been set correctly.
– Make the set-up correctly. (page 34)
• Tracking is not set appropriately.
– Adjust the tracking manually. (page 20)
• The timer indicator is not displayed.
– Press both TIMER simultaneously. (page 32)
• The video heads are dirty.
– Clean the video heads with a commercially
available cleaning tape.
(Continued)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Calling Service Personnel (continued)
The remote control does not work
properly.
• The batteries are exhausted.
– Replace all batteries. (page 10)
• The remote control is operated beyond the
operating range.
– Make sure the remote control is within 30° of
the remote sensor on the VCR. (page 10)
• Too far from the VCR.
– Use the remote control within 7 m from the
front of the VCR. (page 10)
• An obstacle may be in the way of the operation.
– Remove the obstacle.
• The operating mode of the remote control is not
set correctly.
– Press VCR or TV depending on the
equipment you want to operate. (pages 14, 43)
The cassette is ejected immediately after
it is loaded.
• The cassette was inserted with the label side
not paralleling the compartment.
– Reload it carefully. (page 19)
The cassette does not go into the cassette
compartment.
• There is already a cassette in the VCR.
– Eject the cassette and reload the new one.
(page 19)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power supply:
120 V AC, 60 Hz
Power consumption:
External dimensions:
Mass:
19 W
430 × 96.5 × 281 mm (W.H.D.)
3.8 kg
Channels received:
VHF: Channels 2–13
UHF: Channels 14–69
CATV: Channels 1–125
UHF/VHF: 75 Ω F type connector
Standard NTSC
Antenna input/output terminals:
Signal system:
Recording/Playback system:
Recording: VHS format (SP, SLP)
Playback: VHS format (SP, LP, SLP)
Cassette:
Video cassette with
mark
Tape speed:
SLP: 11.1 mm/s, SP: 33.4 mm/s
Video recording/playback time:
SLP: 480 minutes, SP: 160 minutes (When T-160
video cassette is used.)
Fast forward time:
High speed rewind time:
Video input:
Within approx. 80 s (When T-120 video cassette is
used.)
Within approx. 54 s (when T-120 video cassette is
used.)
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Video output:
1 V (p-p), 75 Ω, unbalanced, negative sync., pin
jack
Audio input:
Line input: 308 mV (rms), more than 47 kΩ, pin
jack
Audio output:
Line output: 308 mV (rms), less than 4.7 kΩ, pin
jack
Audio frequency range (Hi-Fi):
Audio dynamic range (Hi-Fi):
Utilization conditions:
20 Hz – 20 kHz
90 dB
Temperature: 5°C to 40°C
Humidity: less than RH 80%
Accessories
Antenna cable ....................................... 1
Remote control..................................... 1
Batteries (AAA) .................................... 2
Designs and specifications are subject to change without notice.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADIAN WARRANTY
TOSHIBA VIDEO CASSETTE RECORDER
To obtain a “CANADIAN WARRANTY”, the consumer must complete and forward the
attached“CANADIANWARRANTYREGISTRATIONFORM”toToshibaofCanadaLimited,
ConsumerElectronicsGroupWarrantyRegistrationOffice,191McNabbStreet,Markham,
Ontario L3R 8H2, within 30 days of purchase!
This warranty offer provides the manufacturer’s parts and labour warranty provided that the consumer
registers for a CANADIAN WARRANTY.
To obtain service under warranty, contact the nearest authorized TOSHIBA SERVICE CENTER or the
nearest TOSHIBA FACTORY SERVICE DEPARTMENT (list enclosed).
PRODUCTS UTILIZED FOR RENTAL OF COMMERCIAL PURPOSES ARE NOT COVERED BY THIS
WARRANTY.
This warranty applies only to the original purchaser and is not transferable. The video head warranty is
alsocovered, duringwhichTOSHIBAwillprovideareplacementheadwarrantedfortheunexpiredportion
of the warranty. This warranty does not apply to sets subjected to misuse, neglect, accident, act of God
orimproperinstallation.Setswithserialnumberremoved,altered,replacedordefacedwillnotbecovered
by this warranty. ALL IN-WARRANTY REPAIRS MUST BE MADE BY A TOSHIBA FACTORY SERVICE
DEPARTMENT, OR BY AN AUTHORIZED TOSHIBA SERVICE CENTER. REPAIRS MADE ELSEWHERE
WILL INVALIDATE THIS WARRANTY.
THIS WARRANTY IS ONLY VALID WHEN THE SET IS PURCHASED FROM AN
AUTHORIZED TOSHIBA DEALER AND USED IN CANADA.
THISWARRANTYISINLIEUOFALLOTHERWARRANTIES, GUARANTIESORAGREEMENTS, WHETHER
EXPRESSED OR IMPLIED, AND NO PERSON, AGENT DISTRIBUTOR, DEALER, SERVICE CENTER
OR COMPANY IS AUTHORIZED TO CHANGE, MODIFY OR EXTEND ITS TERMS IN ANY MANNER
WHATSOEVER.
IMPORTANT: Also keep your “Bill of Sale” as proof of purchase.
WARRANTY:
TYPE OF SET:
PARTS:
Carry-In-Service
Color Video Cassette Recorder
12 Months
LABOUR:
12 Months
VIDEO HEAD:
12 Months
Thank you for purchasing this fine product from one of your authorized: CANADIAN
TOSHIBA DEALERS.
TOSHIBA
HEAD OFFICE
OF
CANADA,
LTD.
191 MCNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA
SERVICE CENTER
TEL: (905) 470-5400
TORONTO: 191 MCNABB STREET MARKHAM, ONTARIO L3R 8H2, CANADA
MONTREAL: 1643 N. SERVICE RD. DORVAL, QUEBEC, H9P 1J1, CANADA
TEL: (905) 470-5400
TEL: (514) 856-4100
VANCOUVER:22171 FRASERWOOD WAY, RICHMOND, B.C. V6W 1J5, CANADA TEL: (604) 303-2500
Printed in China
48
Download from Www.Somanuals.com. All Manuals Search And Download.
|