OWNER’S MANUAL
DATA PROJECTOR
TDP-SW80
(SVGA / With PC Card Slot)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using
SAFETY PRECAUTIONS
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servicing. This unit is fully
transistorized and does not contain any parts that can be repaired by the user.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner's Manual
3. Source of Light
WARNING: Handling the cord on this product or cords associated with accessories sold with
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyes or sight.
this product, will expose you to lead, a chemical known to the State of California
USA only
to cause birth defects or other reproductive harm. Wash hands after handling.
WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to
environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance:www.eiae.org.
USA only
FCC Radio Frequency Interference Statement
Note:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiates radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
USA only
4. Ventilation
2. Power Sources
Openings in the cabinet are
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface. This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or
the manufacturer's instructions
have been adhered to.
WARNING: Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized byToshiba, could void the user’s authority to operate
the equipment.
USA only
Notice:
CANADA only
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe A est conforme à la norme NMB-003 du Canada.
WARNING: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
5. Heat
8. Power-Cord Protection
10. Lightning storms
12. Do not place the product
vertically
The product should be situated
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
For added protection for this
product during storm, or when it is
left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
However, while it is thundering or
lightning, do not touch the
away from heat sources such as
radiators, heat registers, stoves, or
other products (including
Do not use the product in the
upright position to project the
pictures at the ceiling, or any other
vertical positions. It may fall down
and dangerous.
amplifiers) that produce heat.
apparatus and any connected
cable and/or equipment.
This will prevent you from
receiving the electric shock by an
electric surge.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
9. Overloading
13. Stack Inhibited
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as this
can result in a risk of fire or
electric shock.
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
11. Object and Liquid Entry
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
e) If the product has been dropped or
15. Accessories
19. Replacement Parts
22. Do not use the product in
a closed installation state.
damaged in any way.
Do not place this product on an
unstable cart, stand, tripod,
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
f) When the product exhibits a
Do not place the product in a box
or in any other closed installation
state. Otherwise it may overheat.
This could result in a risk of fire.
distinct change in performance -
bracket, or table. The product may
this indicates a need for service.
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved with
care. Quick stops, excessive
force, and uneven surfaces may
cause the product and cart
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
23. When using a wireless
LAN PC card:
(Replacement of the lamp only
should be made by users.)
•Do not use near people
with heart pacemakers
•Do not use near electronic
medical equipment, or in
hospitals or other medical
institutions
•Do not use inside aircraft
or in places where the
wireless LAN card could
interfere with
combination to overturn.
This product incorporates glass
components, including a lens and
a lamp. If such parts should
break, please handle with care to
avoid injury and contact your
dealer for repair service. The
broken pieces of glass may cause
to injury. In the unlikely event of
the lamp rupturing, thoroughly
clean the area around the
20. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
S3125A
16. Damage Requiring Service
projector and discard any edible
items placed in that area.
Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
electromagnetic signals.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
18. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed to
rain or water.
21. Do not leave thermal-
paper documents or easily
deformed items on top of
the unit or near the air
exhaust for long periods
of time.
24. If the use of a wireless
LAN PC card interferes
with another device’s
electromagnetic signals,
cease use immediately.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
d) If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions as an
improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore
the product to its normal
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
operation.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.
25. Do not carry the projector
by having the terminal
cover parts or the PC card
cover part
Plug
Plug
configuration Plug type
Line voltage
220 – 240V
configuration Plug type
Line voltage
200 – 240V
Australian
240V
EURO
UK
Doing so, the projector may fall if
that cover comes off, and injury or
damage may result.
10A
Switzerland 200 – 240V
240V
6A
220 – 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
North American 200 – 240V
240V
15A
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the crucial internal parts. To prevent the unit from possible damage, do not use the unit for
at least 2 hours when there is an extreme or sudden change in temperature
.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
• Do not use the product vertically in any upright position or slantwise in an angle of 20
degrees or more.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to use
it in that situation, the malfunction may result. Ensure to wait until the condensation
naturally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use it with the
ambient temperature being lowered.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS (Continued)
Avoid Volatile Liquid
OTHER CAUTIONS AND INFORMATIONS
Copyrights
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.
Showing or transmitting commercial imaging software or broadcast or cable-broad
casting programs with the purpose of other than the personal and private viewing,
including modifying images using the freeze or resize functions, or displaying with the
varying aspect ratio of the images, could violate the direct or indirect copyrights of the
imaging software or broadcast program, etc., if done without first consulting with the
copyright holder. For this reason, please take appropriate measures before performing
one of the actions listed above, including obtaining a license from the copyright holder.
Wireless LAN PC Card
• Do not connect the supplied wireless LAN PC card to devices other than this unit. Doing
so could cause malfunction.
Disposal
• To protect the PC card from static electricity, touch some nearby metal, such as a
doorknob or aluminum window frame, before touching the PC card, to rid your body of
static electricity.
This product contains substances which are harmful to humans and the environment.
• Solder used in the internal parts contains the lead.
• This PC card is a radio product. Concerning the regulations applied in each country/area,
please refer to “Information to the user” supplied.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Trademarks
In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.
Model No.
Serial No.
• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas
Instruments.
Retain this information for future reference.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems
Incorporated.
EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,
operation, theft or mischief by third parties, other accidents, or use under abnormal
conditions including erroneous or improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
Notational Conventions Used in This Manual
• References to pages with related information are annotated as follows.
p.36
For example, if making a reference to page 36:
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
REMOTE CONTROL BATTERIES
• Be sure to use AA size batteries.
• Do not reverse the polarity when inserting the battery.
• Toshiba bears no responsibility for information being intercepted or leaked due to the use
of a wireless LAN, or any damages therefor.
• Do not recharge, heat, disassemble, short-circuit, or burn the battery.
• Do not use the battery beyond the expiration date indicated on the battery or leave a
dead battery in the remote control.
• Do not mix batteries of different types, such as alkaline and manganese. Do not mix new
and used batteries.
Using the batteries improperly may cause them to explode or leak and lead to burn or injury. If
battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult a
doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.
(Dispose of the used tissue paper as flammable garbage after moistening with water.)
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Automatic demonstration ................................................................................ 45
Playing a slide show from a thumbnail list ...................................................... 46
Checking the projector status ............................................................................ 48
Status display ................................................................................................. 48
Installing the applications................................................................................... 49
Using the Wireless Utility ................................................................................... 50
Displaying a computer’s screen via the projector ........................................... 50
Displaying a JPEG image saved on a computer via the projector.................. 52
Operating the projector................................................................................... 53
Document camera function ............................................................................ 54
How to use the JPEG Conversion Tool .............................................................. 55
Launching the JPEG Conversion Tool ............................................................ 55
Converting an image file................................................................................. 55
Converting files created with Microsoft® PowerPoint® ..................................... 56
Making a presentation with converted JPEG files .......................................... 57
Creating a screen capture and converting it into a JPEG file ......................... 57
Setting up the projector using a Web browser ................................................... 58
How to use the “Projector Configuration Tool” ................................................ 58
Before Using
SAFETY PRECAUTIONS ..................................................................................
IMPORTANT SAFETY INSTRUCTIONS ...........................................................
POWER SUPPLY CORD SELECTION..............................................................
IMPORTANT PRECAUTIONS ...........................................................................
2
3
9
9
EXEMPTION CLAUSES .................................................................................... 10
OTHER CAUTIONS AND INFORMATIONS ...................................................... 11
REMOTE CONTROL BATTERIES .................................................................... 11
CONTENTS ....................................................................................................... 12
Preparations
Checking the package contents ......................................................................... 14
Names of each part on the main unit................................................................. 15
Names of each part on the control panel and remote control............................ 16
Parts on the rear panel ...................................................................................... 17
Preparing and using the remote control............................................................. 18
Placement .......................................................................................................... 19
Connection......................................................................................................... 20
How to use the PC card slot .............................................................................. 21
Maintenance
About lamp......................................................................................................... 62
Lamp replacement ............................................................................................. 62
Lens and main unit cleaning .............................................................................. 64
Operations
Turning the power on and off ............................................................................. 22
Basic operations ................................................................................................ 24
Using handy features ......................................................................................... 26
Using auto setting........................................................................................... 26
Cutting off the picture and sound temporarily (Mute) ..................................... 28
Freezing the image (Freeze) .......................................................................... 28
Using the menus ................................................................................................ 29
How to use the menus .................................................................................... 29
The image adjustment menu .......................................................................... 30
The display setting menu................................................................................ 31
The default setting menu ................................................................................ 32
Displaying Information (Status display) .......................................................... 33
Setting up the wireless LAN............................................................................... 34
Functions ........................................................................................................ 34
Communication mode .................................................................................... 34
Caution when using the wireless LAN functions ............................................ 35
Setup using the Wireless/Card menu ............................................................. 36
How to enter characters ................................................................................. 37
Setting up the network.................................................................................... 38
Computer settings .......................................................................................... 41
Projecting images stored in a memory PC card ................................................ 42
Memory PC cards........................................................................................... 42
JPEG files....................................................................................................... 43
Setting slideshow options ............................................................................... 43
Others
Trouble indications ............................................................................................. 65
Before calling service personnel ........................................................................ 66
Specifications..................................................................................................... 68
List of general specifications .......................................................................... 68
Separately sold product.................................................................................. 68
List of supported signals (RGB signals) ......................................................... 69
List of supported signals (Y/PB/PR signals) .................................................... 70
List of supported signals (Video, S-Video signals) ......................................... 70
Pin assignment of COMPUTER-1/2 & MONITOR terminals .......................... 70
CONTROL terminal ........................................................................................ 71
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Names of each part on the main unit
Checking the package contents
Please make sure that the following items are included in the box, along with the main unit. If
any item is missing, please contact the store immediately where you purchased the product.
(7) (6)
(5)
(4)
(3) (2)(1)
(1)
(5)
(8)
(6)
(7)
(2)
(3)
(8)
(9) (10) (11)
Back
(12)(9) (13) (14)
Front
(4)
Name
: Function
■ (5) Power cord (See note)
■ (6) RGB cable (3m)
■ (7) Carrying bag
p.25
(1) Foot adjuster release button : Press to stow the foot adjuster.
■ (1) Remote control
■ (2) R6 (SIZE AA) batteries for remote
control (2)
p.18
: Senses commands from the remote control.
(2) Infrared remote sensor
(3) Lens
: Projects expanded image.
(4) Air intake
(5) Speaker
(6) Control panel
(7) Zooming lever
(8) Air exhaust
(9) Tilt adjuster
: Draws in air from outside the projector.
: Outputs audio sound.
■ (3) CD-ROM
■ (4) Owner’s Manual
■ (8) Wireless LAN PC card
• “About the Wireless LAN PC Card”
p.16
: Operates the projector.
p.25
: Adjusts screen size.
Note
: Expels air that has grown hot inside the projector.
The shape and number of supplied power cords vary depending on the product destination.
p.25
: Adjusts the projector’s horizontal tilt.
p.21
(
(
(
(
(
10) PC card slot section
11) Rear panel
12) Focusing ring
13) Foot adjuster
14) Lamp cover
: Mounts/removes the PC card.
: Connects external devices.
p.17
◆The Supplied CD-ROM
p.25
: Adjusts screen focus.
The supplied CD-ROM contains the owner’s manual including information not available for
p.25
: Adjusts the vertical projection angle.
its simplified hardcopy, Owner’s Manual (Getting Started), Acrobat® Reader™ to view the
p.63
: Remove to replace lamp.
p.49
manual, and application software
to use the functions of the wireless LAN/PC card.
■ Installing Acrobat® Reader™
Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader
Installer. Follow the on-screen instructions to install the software.
■ Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover and list of bookmarks appear. Click on a bookmark title to view that
p.
section of the manual. Click on
to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader™.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the control panel and remote control
Parts on the rear panel
Control panel
Remote Control
(1) (2)(3)(4)(5)(6) (7)
(8)
Remote control
transmitter
(9) (10) (11)
(9)
(1)
(2)
(8)
(10)
(4)
(6)
(3)
(2)
(7)
(6)
(14)
(3)
(4)
(5)
(20)
(19)(18) (17)(16) (15) (14) (13)(12)(11)
: Main Function
(8)
(12)
(13)
(7)
Name
p.18
: Senses commands from the remote control.
: When operating the projector via a computer, connect
(1) Infrared remote sensor
(2) CONTROL terminal
p.71
this to the controlling computer’s RS-232C port.
(1)
p.21
(3) CARD indicator
(4) UNMOUNT button
(5) RESET switch (inside depression) : Press if CARD indicator turns red.
: Displays PC card’s status.
p.21
p.21
: Press before removing PC card.
p.21
(6) Eject button
(7) PC card slot
: Press to remove PC card.
: Insert PC cards here.
p.21
(8) AUDIO OUT terminal
(9) MONITOR terminal
: Outputs audio signals.
: Connect to a computer display, etc.
Name
: Main Function
(1) ENTER button
(2) MENU button
(3) SET UP button
(4) ON/STANDBY button
(5) ON indicator
(6) INPUT button
(7) RETURN button
(8) Selection button
(9) LAMP indicator
10) TEMP indicator
11) FAN indicator
12) FREEZE button
13) MUTE button
14) Numeric keypad
: Accepts the selected mode.
: Displays menus.
: Sets up image and mode.
: Turns the power on/off (standby).
: Displays whether power is on or off.
: Selects input.
: Goes back one screen.
: Menu selections and adjustments,etc.
: Displays lamp mode.
: Lights when internal temperature too high.
: Displays cooling fan mode.
: Pauses image.
: Cuts off the picture and sound temporarily.
(
10) COMPUTER 2 terminal
:
Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video equipment.
p.29
(
(
(
11) Main power switch
12) AC IN socket
13) AUDIO IN terminal
: AC power line ON (standby)/OFF.
: Connect the supplied power cord here.
p.26
p.22
:
:
Input audio signals from a computer or video equipment
with a component video signal output terminal.
Input RGB signal from a computer or other source, or a
component video signal (Y/PB/PR) from video equipment.
p.22
p.24
(
14) COMPUTER 1 terminal
p.30
(
(
(
(
(
15) S-VIDEO terminal
16) AUDIO (L/R) terminal
17) VIDEO terminal
18) AUDIO (L/R) terminal
19) USB terminal
: Input S video signals from video equipment.
: Input audio signals from video equipment.
: Input video signals from video equipment.
: Input audio signals from video equipment.
: Provided for servicing purposes only. Do not use for
any connection.
p.23
p.65
p.28
(
(
(
(
(
p.65
p.28
(
20) Antitheft lock hole
: Attach a safety cable or any other antitheft device.
: Use to set up the wireless LAN. Numbers and charac-
p.37
ters can be entered.
Note
• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the
product also supports signals from video equipment marked “Y/CB/CR.”
Note
• For the remainder of this manual, buttons are referred to as follows:
Selection buttons ⇒
; ENTER button ⇒
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control
Placement
■ Loading dry-cell batteries
into the remote control
q Remove the battery cover.
■ Operating the remote
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
control
The factory setting is “floor-mounted front projection.” Set the Projection mode in the
Point the remote control toward the
projector’s infrared remote sensor,
and press a button on the remote
control.
p.32
default setting menu
, in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
• Operating the projector from the front
w Insert the dry-cell batteries.
Ceiling-mounted front projection
Ceiling-mounted rear projection
Be sure to align the plus and minus
ends of the batteries properly.
Approx. 15°
Approx. 5m
WARNING
Two batteries (R6, SIZE AA) are used.
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
• Operating the projector from the rear
e Replace the battery cover.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
(1)
(2)
Approx. 15°
Approx. 5m
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)
Screen
As seen from above
Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones.
a (min length) = projection size (inches) × 0.04064
°
90
a (max length) = projection size (inches) × 0.04878
projection distance a (m)
projection
size (inches)
height (H)
(cm)
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
As seen from the side
min length
max length
(zooming max) (zooming min)
Lens center
24.6
40
60
—
1.20
1.95
2.93
3.90
4.88
7.32
9.76
—
12.8
20.2
30.0
40.2
50.3
75.4
100.6
123.8
1.62
2.44
3.25
4.06
6.10
8.13
10.00
H
80
°
90
100
150
200
246
a
a is the distance (m) between the lens and the
screen, and corresponds to a range of 1.20 m to
10.00 m. H is the height from the image bottom to
the center of the lens.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
How to use the PC card slot
The wireless LAN PC card enables you to connect the projector wirelessly with a personal
Before connection
• Read the owner’s manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal
• Turn off the power of both devices before connecting.
p.34
computer that supports IEEE802.11b based wireless LAN.
(Please note that commu-
nication between all the computers based on IEEE802.11b and this projector is not
guaranteed.) You can also use a commercially available memory card to project JPEG
image files using this projector. p.42 Please follow the steps below when removing or
mounting a PC card.
p.69
, etc.
• The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
■ Mounting a PC card
■ Removing a PC card
q Insert the PC card.
q Look at CARD indicator.
Audio amplifier, etc.
After making sure of the card orienta-
If it is off, proceed to step r.
Computer (for control)
tion, press it in firmly until it stops.
CARD indicator
Video recorder,
DVD player, etc.
UNMOUNT button
VCR
To audio output
White (L)/Red (R)
To video
output
To audio output
White (L)/Red (R)
Video cable
(not supplied)
To S-Video
output
To audio input
White (L)/Red (R)
To
RS-232C
terminal
p.71
Control cable
w Press the UNMOUNT button.
Audio cable (not supplied)
S-Video cable
(not supplied)
AV cable
(not supplied)
Begins processing for PC card removal.
PC Card
e Wait until CARD indicator goes
out.
When the PC card is detected correctly,
the CARD indicator comes on in green.
Never remove the PC card while lit.
Doing so could damage the PC card or
corrupt your data.
r Press the Eject button.
Eject button
Audio cable
(not supplied)
RGB cable
(supplied)
RGB cable
(not supplied)
Audio cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To RGB
output
To RGB
output
To audio output
The Eject button is a bit stiff, so
press firmly while supporting the
projector. Be careful to avoid injury
when doing so.
To audio
output
To Y/CB/CR output
Green (Y)/Blue (CB)/Red (CR
)
Conversion adapter BNC-pin
(not supplied)
Computer
DVD video recorder, etc.
Computer
■ If CARD indicator turns red
CARD indicator
RESET switch
Press the RESET switch with a thin pin
or similar implement (it is at the bottom
of a recess).
Notes
• COMPUTER terminals 1 and 2 function identically.
• The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Turning the power on and off
Notes
■ Connecting the power cord
• The start-up screen will disappear after a moment.You can dismiss the start-up screen
before this by performing any operation.You can also configure the start-up screen not to
Insert the power cord connector into the
AC IN socket of the projector.
1
p.31
appear via the Display setting menu
.
• The first time you use the projector after purchase, after the start-up screen disappears,
Insert the power cord plug into a wall or
other power outlet.
2
p.24
the Language menu is displayed
.
Power cord connector
(Supplied)
■ Turning the power off
■ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
Press the ON/STANDBY button again.
2
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
■ Turning the power on
When cooling lamp
During internal cooling
After cooling complete
1
Turn on the main power
switch.
(Green)
Flashing
(Orange)
(Green)
(Off)
(Green)
(Off)
(Off)
The ON indicator will change to
orange, indicating standby mode.
(Orange)
(Orange)
(Orange)
A
B
C
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
A
B
Remote
Control
2
Press the ON/STANDBY
button.
Control panel
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
Start-up screen
The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
In standby mode
C
Note
• The projector consumes about 18W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
CAUTION
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes or sight.
PRECAUTION
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and
its lifetime will be shortened.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
5
Turn on the power.
Turn on the power by following the instructions in “Turning the power on”
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot
1
p.22
.
adjuster.
2
Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
q Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
1
focus, adjust it according to the step .)
6
w To adjust the horizontal angle, use
the tilt adjuster.
q Use the
or
button to select the
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
desired language and press the
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
To stow the foot adjuster, hold up the
projector while pressing the foot adjuster
release button, then slowly lower the
projector.
2
6
7
Adjusting the screen size and focus
q Use the zooming lever to adjust the screen
w Using the
power and press the
The lamp power, if selected, will be toggled without
pressing the button. The display automatically
or
button, select the lamp
1
2
button.
size.
w Use the focusing ring to adjust the focus.
disappears in a few seconds.
Adjusting the volume with the
The speaker volume can be adjusted when an audio signal is being input.
buttons
Notes
• When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Notes
p.32
Default setting menu
, the Language and Lamp power menus will be
• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
displayed the next time when the power is turned on.
• The language can also be set via the Display setting menu
p.31
and Lamp power
p.32
via the Default setting menu
.
• This owner’s manual assumes that English has been selected.
• The DMDTM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please
note that these are not malfunctions.
Activate the connected device.
Turn on and start the connected device such as a computer.
3
4
p.69
• Although this projector supports a wide range of RGB signals
, any resolutions not
supported by this projector (SVGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to SVGA resolution.
Press the INPUT button.
An image of the connected equipment is projected.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
• If a signal not supported by the projector is input, the “Unsupported signal” will appear.
• If no signal is being input from the connected device, the “No signal” will appear.
Each time you press the INPUT button, it switches to the input of the connected
equipment.
Notes
p.32
• When [Auto input search] is set to [On] in the default setting menu
, the image of
the equipment which is connected and turned on is projected.
• Moving pictures generated with the DVD software for computers may appear unnatural if
it is projected with this projector, but it is not a malfunction.
• If an unavailable operation button is pressed, the
icon will appear.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features
● Manual adjustments and settings
■ Using auto setting
Remote
Control
The menu items of the Set up menu vary depending on the input type, as shown in
the table below.
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.
Control panel
Use the
buttons to adjust the items in the table below, then press
1
Press the SET UP button.
the RETURN button when you are finished.
The Set up menu appears.
Video
S-video card
PC
2
Press the SET UP button again.
The menu item is automatically adjusted/set.
Select Item
Description
Computer Y/PB/PR
Auto. Keystone Automatically corrects the keystone distortion.
Press
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
For computer input, the
icon will appear during
.
processing.
Keystone
Correct the keystone (trapezoid) distortion of the
screen.
p.27
For manual adjustment and setting, see the following table
.
Screen shrinking
downward
Screen shrinking
upward
Note
• The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector
Auto setting Automatically adjusts items such as the sampling
phase depending on the type of input signal.
Press the SET UP button.
Yes
No
No
No
p.69 p.70
,
.
●Correcting the keystone distortion
Phase
Adjust with
to eliminate flicker.
Yes
Yes
No
No
No
No
No
No
p.25
When the foot adjuster
is used to change the projector placement angle while
Frequency Adjust with
to eliminate periodic patterns
projecting the image, the picture will undergo keystone (trapezoidal) distortion.
and flickering when many vertical lines appear
on the screen.
This projector is capable of correcting this keystone distortion
Before correction After correction
.
H-position Adjust the horizontal position of the image.
Yes
No
No
No
Move left
V-position Adjust the vertical position of the image.
Move down Move up
Adjusts the clamp pulse position.
Lower Higher
Adjusts the clamp pulse width.
Narrower Wider
Move right
Yes
Yes
No
No
No
No
No
No
Clamp 1
Clamp 2
Yes
No
No
No
1
2
Press the SET UP button.
Press the
button.
The keystone distortion is automatically corrected. The
correction.
icon appears during this
● Manual adjustment
Press the SET UP button to display the Set up menu and select [Keystone]. Use
the buttons for keystone adjustment. When the adjustment is finished, press
the RETURN button. The menu disappears.
Notes
• Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
• Keystone adjustment is available for the keystone distortion in a slant angle of ±15
degrees.
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features (Continued)
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings using
■ Cutting off the picture and sound temporarily (Mute)
p.16
the operation buttons
on the control panel (main unit side) and remote control.
Remote
Control
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
■ How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Press the remote control’s MUTE button.
The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)
Display the Setting display menu
1. Press the MENU button
2. Select a Category
Notes
Select a category by using
.
Displays the current
adjustments and settings of
selected category.
• The
icon will appear while mute is in effect.
There are following four
categories:
• Operating any other functions will also cancel the muting.
Item shown with gray cannot
be adjusted with the current
input source.
■ Freezing the image (Freeze)
p.30
Image adjustment menu
Remote
Control
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
p.31
p.32
p.33
Display setting menu
Default setting menu
Status display menu
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released when pressing
the FREEZE button again.)
3. Adjustments & Settings
Press
to open the menu.
5. Press the MENU button
The Wireless/Card
menu appears.
* Displayed only in wireless/card
input mode.
Notes
Item
Adjustment/Setting Value
• The
icon will appear while freeze is in effect.
• Other operation will also release the freeze.
• Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
• If you use this function on video software sold on the market, broadcast or
broadcast on cable except for the purpose of your private viewing and listening, it
may infringe the copyright protected by the copyright laws.
To Wireless/Card
These marks signify the
items can be adjusted/set
p.36
menu
.
This mark signfy that
there are options.
by using
.
Press
to display a
list of options.
These marks signify the items can
be selected from the list by using
.
After an item is selected, apply it
by pressing
.
The figure shows displays given for operation instructions purposes. As the display
may differ depending on the item, use the following pages as a reference.
6. End
Press the MENU button
The menu disappears.
4. Back
Press the RETURN button
Note
• Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
■ The display setting menu
Use this menu to set screen display-related items.
■ The image adjustment menu
Use this menu to adjust image-related items.
Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”.
Description
Item
Video
S-video
PC
card
Item
Contrast
Description
Computer Y/PB/PR
Screen size
(Full): Display with 800 × 600 dot resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR
Adjust the image contrast.
Yes
Yes
No
No
No
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Lower
Brightness Adjust the brightness of the image.
Darker Brighter
Adjust the color of the image.
Lighter Deeper
Adjust the tint of the image color.
Reddish Greenish
Sharpness Adjust the sharpness of the image.
Softer Sharper
Set the function to reduce screen noise. No
On (Enable) Off (Disable)
Press . Toggle the picture mode with
Higher
)
Yes
Yes
Yes
Yes
Yes
Yes
Select one of the languages below to use for displaying the menu and messages
Language
[
: Enter setting mode]
[
:Selection]
[Apply:
]
Color
Tint *1
English/Français/Deutsch/Italiano/Español/Português/
/
Svenska/Türkçe/
/
/
/
No
Background Screen to display when there is no input signal
(Logo)
(Blue)
(Black)
Icon
Display icons as function guides
On
Off
Off
Yes
Yes
Yes
Yes
No
Display start-up screen when power is turned on On
Start-up screen
Noise
reduction
Note
Picture
mode
Yes
No
• If “Thru” is selected for screen size, portions exceeding the native resolution (800 × 600
pixels) will not appear on the screen. Note that for RGB signals with clock frequency
110MHz or lower, all input pixel signals are sampled. However, if the clock speed is
higher than this, the RGB pixel signal is thinned before sampling.
/
.
Bright/Standard/True color
R-level
G-level
B-level
Adjust red of the image color.
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Less red
Adjust green of the image color.
Less green More green
Adjust blue of the image color.
Less blue More blue
NTSC mode*1 Set the black level with
US: NTSC (US) mode
Japan: NTSC (JAPAN) mode
More red
/
button.
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to
[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is
set to US for other languages.)
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
■ The default setting menu
This menu shows placement status and other settings.
■ Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
Description
Item
“Yes”: displayed, “No”: not displayed
p.19
(Rear mounted
from ceiling)
Projection
mode
Sets projection mode in accordance with Placement Style.
Video
S-video
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
PC
card
Yes
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
(Mounted
Item
Description
Computer Y/PB/PR
(Standard)
(Rear)
from ceiling)
Input
Input source name
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
No
No
No
No
Yes
No
No signal
power off
Set the timer to wait for the power to be turned off after signal input stops.
Press . Switch with and
Mode name
H-resolution
V-resolution
H-frequency
V-frequency
Sync
Signal format
Video mode
Lamp time
RGB input mode [Note 1]
.
Horizontal resolution (in dots)
Vertical resolution (in dots)
Horizontal sync frequency
Vertical sync frequency [Note 2]
Sync signal polarity [Note 3]
Y/PB/PR signal format
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Auto input
search
Set whether the input with signals is only selected or not.
On
Off
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Auto
High
High
Color method of video signal
No
Lamp power [Note 1]
Fan mode [Note 2]
Reset all
Time of lamp use [Note 4]
Yes
Yes
Yes
Yes
Yes
Sets the lamp power.
Low
Standard
Standard
Lamp reset count The count for lamp replacement Yes
Total time
Version
Sets the cooling fan speed.
The total time that this projector is used Yes
Press
.
Firmware version [Note 5]
Yes
Yes
No
Resets all adjustments and settings to their factory settings.
Notes
1: The mode of supported RGB signals
Notes
is shown.
p.69
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. The setting is cleared when you turn the power off, and the item is reset to Standard the
next time you turn the power on.
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a store about getting a TLPLW5 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
•
Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.
• When you turn off the projector even if Power on is set to Auto, you must press the ON/
Note
STANDBY button to turn the power off.
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the wireless LAN
■ Functions
■ Caution when using the wireless LAN functions
The following functions are available via wireless communications, when the wireless LAN
PC card and dedicated Wireless Utility software
Note: A wireless LAN PC card except the supplied one (or recommended by
Toshiba) does not work with this product. Please ask your dealer about the
available wireless LAN PC card.
The Wireless LAN in this unit uses the 2.4 GHz waveband. If there is a similar wireless
LAN in the area, or a wireless device using the 2.4 GHz waveband, or a microwave
oven, the communication efficiency of this apparatus will be reduced, and may become
unusable, but it is not a fault. If this happens, check an area away from the current
location that will not cause radio interference to medical, industrial and public equip-
ment, and change to it, or stop using the unit.
p.50
included with this projector are used.
1) Displaying a computer’s screen via the projector
The computer’s desktop screen can be sent, as well as the screens of a variety of
software applications, to the projector for display.
2) Displaying an image saved on a computer via the projector
JPEG files can be sent to the projector for display.
3) Operating the projector by means of a computer
Some of the same functions available from the remote control can be performed.
■ Communication mode
This projector supports both Ad hoc and Infrastructure Communication modes.
◆ Ad hoc communication mode
This is transmission mode to communicate
between wireless LAN equipment.
Wireless communication can be performed via the
simple configurations. This function can only be
used if the projector is in range of the computer’s
wireless signals.
For security reason, confirm the specifications of your computer for the distance that
the radio wave can reach. The coverage of this projector may vary, depending on the
computer and the surrounding environment. When tested with a PC manufactured by
Toshiba with built-in wireless LAN system, the coverage is approximately 60 m with an
unobstructed path between the projector and computer placed indoors. This figure is
not guaranteed and should be considered as merely a guideline.
◆ Infrastructure communication mode
This mode allows the projector to communicate
with a wireless-LAN/wired-LAN mixed network via
an access point. (It even allows for communication
To premises
LAN or Internet
between wireless LAN devices.)
Hub
Connecting to the rest of the world via a wired LAN
or the Internet generally requires a high level of
security.
Access point
Use the appropriate transmission mode for your network environment.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the wireless LAN (Continued)
■ Setup using the Wireless/Card menu
● Projector settings (Be sure to read this subsection.)
■ How to enter characters
Use the numeric keypad on the remote control to enter characters. Enter each charac-
ter of interest and press the
button to accept it.
The factory settings can be used as-is. However, if you need higher security, the
projector settings should be changed.
Text input mode
1. Press the MENU button twice
Display the Wireless/Card menu.
Remote
control
buttons
Only-digital input items
(Examples:
Alphanumeric character/symbol input items
(Examples: SSID, Key settings)
* Displayed only in Wireless/Card input mode.
2. Select a Category
TCP/IP settings)
Select a category by using
.
Displays the current settings
of selected category.
Dimmed items cannot be
changed under the current
settings.
“1” “.”
“2” “A”
“@” “-”
“B” “C”
“_”
“a”
“d”
“g”
“j”
“1”
“2”
The following three categories
are available:
“b”
“e”
“h”
“k”
“c”
“f”
“i”
“3” “D” “E”
“4” “G” “H”
“F”
“I”
“3”
“4”
“5”
“6”
“7”
“8”
“9”
p.38
p.43
p.48
Network setup
Slide Show setup
Status display
“5” “J”
“K”
“L”
“l”
“6” “M” “N” “O” “m” “n”
“o”
“q”
“v”
“x”
“7” “P” “Q” “R” “S”
“p”
“u”
“w”
“r”
“s”
“z”
“8” “T”
“U” “V”
“Y”
“t”
“9” “W” “X”
“Z”
“y”
3. Make settings
Press
to open the menu.
“0” “space "#$%&'()*+,-./:;<=>?@[\]^_`{|}~”
Erase one character.
“0”
These marks signify that
options can be selected by
Erase one character.
using
.
Item
Setting Value/Option
5. End
Press the MENU
button
The menu disappears.
The figure shows a typical example. As the display
may differ depending on the item, use the following
pages as a reference.
4. Back
Press the RETURN button
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the wireless LAN (Continued)
• [SSID]
■ Setting up the network
This is an ID code for connecting to specific individuals over a wireless LAN. This may
also be called “Network group” or “Network name”. Please read the following carefully.
p.36
If you select Network in step 2 in “Projector settings”
, the following items can be set.
Item
Description
Note 1: The SSID is set to DPJ when shipped from the factory. If you leave this setting
as it is, security may be compromised due to access by a third party using the
“Wireless Utility” within the projector’s possible communication area. Before
using the projector, therefore, be sure to set SSID to a character string different
from the default.
Note 2: When you use the Ad hoc communication mode, if there is a similar SSID
network group (for example DPJ, DPJ1, DPJ2, etc.) in the possible communi-
cation area, it is possible that your projector name will not be displayed in the
Wireless Utility projector list column. If this is the case, set SSID to a com-
pletely different character string.
Ad hoc
Infrastructure
Mode
Use
to select the number (1 to 11) to be set.
Channel
SSID
Specify an arbitrary character string (1 to 32 characters).
[
to
: Enter the setting mode]
[
: Move from digit to digit]
[
[
: Enter the string] [Accept:
]
Encryption
Key
On
Off
Specify an arbitrary character string.
(A string of 5 or 13 characters or a string of 10 or 26 characters in
hexadecimal notation)
• [Encryption]
Enable or disable encryption for security purposes.
[
to
: Enter the setting mode]
[
: Move from digit to digit]
: Enter the string] [Accept:
]
Note: Encryption is factory-set to Off. If you use the projector with this setting left
unchanged, security may be compromised due to access by a third party using
the Wireless Utility within the projector’s coverage. Before using the projector,
therefore, be sure to set Encryption to On.
DHCP
Use
Not use
TCP/IP
Enter single-byte numeric characters to specify the IP
address/subnet mask/gateway.
[
:
Enter the setting mode
]
[
:
Select an item
]
[
: Move
]
from digit to digit] to : Enter the string] [Accept:
[
]
• [Key]
Setting
initialization
When you have set Encryption to On, the encryption key must be set. For use at an
encryption level of 64-bit, specify a string of 5 arbitrary characters or a string of ten
characters in hexadecimal notation. For use at the 128-bit level, specify a string of 13
arbitrary characters or a string of 26 characters in hexadecimal notation.
Initialize the wireless LAN settings.
: Enter the execution mode] [Yes
[
No] [Accept:
Projector
name
Specify an arbitrary character string (0 to 8 characters).
[
: Enter the setting mode]
[
: Move from digit to digit]
[
to
: Enter the string] [Accept:
]
Note: Alphabetic characters (A to F, a to f) used in hexadecimal notation are case
insensitive; the uppercase characters and their lowercase equivalents are
handled to be identical.
Other
Remote control/Browser authentication/Password/Status
notification/SMTP server/Destination address
* To enter characters, use the numeric keypad on the remote control.
The higher the number of bits, the stronger the encryption, and hence the harder it will
be for a third party to decipher your communications. However, setting higher encryp-
tion levels may slow down communication speed. To set the highest security level,
specify a 128-bit encryption key. For higher security, avoid using a word found in a
dictionary and change the key sometimes.
Note
• The wireless LAN settings take effect the moment you closes the menu.
● Details on individual items
• [Mode]
Set the following item if you have set the communication mode to Infrastructure.
Your projector is set to Ad hoc in the factory. Change the setting if you want to use the
projector in Infrastructure mode.
• [DHCP]
If you set DHCP to Use, the IP address of the projector is assigned automatically by the
DHCP server. If your network environment does not assign IP addresses automatically,
set DHCP to Not use, then set the following item TCP/IP manually.
• [TCP/IP]
If you have set DHCP to Not use, ask the network administrator to check for the
following items, then perform the TCP/IP settings manually.
• [Channel]
Usually, you do not have to set this item. If a network group having the same SSID
already exists in the projector’s coverage, the channel is changed automatically to the
channel of that network group.
Note 1: If a set channel is in bad connections for wireless connection, try the other
channels to avoid the effects of radio waves to select the one in possibly the
best communication conditions.
Note 2: To communicate in Ad hoc mode with a computer that cannot change the
channel, start up the projector before the computer.
• IP address
An IP address is a unique number assigned to a terminal for connection to the
Internet. The format is a string of four dot-separated three-digit numbers. (Example:
111.112.xxx.xxx)
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the wireless LAN (Continued)
• Subnet mask
■ Computer settings
A subnet mask is used to determine what subnet the IP address assigned to a
terminal belongs to. (Example: 255.255.xxx.xxx)
• Gateway
This value specifies the device, such as a router, to be used to access servers outside
the network. It is identified by the IP address. (Example: 111.112.xxx.xxx)
Refer to instruction manuals of your computer or wireless LAN PC card to perform the
following settings.
• Select Ad hoc (for some PC cards, this is Peer-to-Peer Group).
• Set the Channel to channel assigned to the projector (in factory reset mode, this is set to
10).
• [Setting initialization]
This item resets the wireless LAN settings to their factory defaults.
• [Projector name]
This can be used to identify projectors when communicating with multiple projectors, or
if there is a possibility that another person who is out of communication range will be
using the same projector. It is recommended this is set to prevent wrong transmission.
For some computers, you cannot set the channel in Ad hoc mode.
• Set SSID (for some types of PC card, use Network name instead) as the same as
projector’s SSID (at factory shipment, this is set to DPJ).
• If Encryption and Key are set on the projector, set to the same values.
• [Other]
Note: It is imperative that the projector and computer encryption settings are the same.
If the settings are different, the encryption may be invalid when sending in the Ad
hoc communication mode, so be careful.
This item is expanded into the following items:
Item
Description
Remote
control
Select whether this projector is to be remote-controlled by the
computer.
Allowed
Presentation
Forbidden
Allowed
: Always accepts remote commands from the computer.
Presentation : Accepts remote commands only from the computer,
the screen of which is currently being displayed via
the projector by the Wireless Utility (Update
automatically).
Forbidden
Enable or disable password authentication for access to the setting
menu of the Projector Configuration Tool. On Off
: Always ignores remote commands from the computer.
Browser
authentication
Set the password to be made valid for access to the setting menu
when [Browser authentication] is set to [On]. Specify a string of
arbitrary characters (1 to 8 characters).
Password
[
: Enter the setting mode]
[
: Move from digit to digit]
[
to : Enter the string] [Accept:
]
Select whether to automatically send error information to a specified
e-mail address if an error occurs, for example, when the lamp has
Status
notification
blown. On
Off
Set the IP address of the SMTP server.
SMTP server
[
: Enter the setting mode]
[
: Move from digit to digit]
[
[
to : Enter the string] [Accept:
]
Set the e-mail address of the recipient of the status notification,
Destination
address
[
: Enter the setting mode]
[
: Move from digit to digit]
to : Enter the string] [Accept:
]
PRECAUTIONS
• Browser authentication and Password are factory-set to Off and no string,
respectively.You should set them as soon as possible.
• If you have forgotten your password, set it again using the menu on the main unit.
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting images stored in a memory PC card
This projector can read JPEG files from a memory PC card to display them on the screen.
This allows you to give presentations without a computer, create an advertising screen
board using the slideshow function, and more. (The projector cannot reproduce animation
effects such as those produced by Microsoft® PowerPoint®.)
■ JPEG files
(1) Supported file extensions are jpg, JPG, jpeg, and JPEG.
(2) The maximum number including both folders and files is 512.
(3) Some JPEG files are not supported by this projector.
The limitations in (3) above can be alleviated by converting the JPEG file with the
■ Memory PC cards
● PC card slot types
p.55
supplied JPEG Conversion Tool
software application.
■ Setting slideshow options
The PC card slot installed on this projector is TYPE II (PCMCIA Release 2.1)-compliant.
Please use memory PC cards and conversion adapters compliant with this type of PC
card slot.
Slideshow is the function to display the JPEG image files stored in a memory PC card
one after another at fixed time intervals. When switching from one image to the next,
Slideshow can add various display effects (transitions) to them. If you select Slide
p.36
Only a 3.3-V PC card can be used. (A 5-V only PC card cannot be used.)
Show in step 2 in “Projector settings”
, the following items can be set.
● Supported storage media types
This projector supports the following types of ATA-compliant storage media. This
owner’s manual refers to the combination of the ATA conversion adapter and media in
use as a “memory PC card.”
Item
Description
Manual
Auto. (Select whether to automatically switch to
wireless/card input when a PC card in plugged.)
PC card
display
Storage media that can be used as-is
On
Off (Select whether to automatically start a slide show
when a PC card in plugged.)
Auto. demo
Flash ATA card, TOSHIBA Mobile Disk
Storage media that can be used in combination with each of the ATA conversion
adapter types
Select the slide show display interval from among the following
Interval
options using
:
5 sec./10 sec./30 sec./1 min./3 min./5 min./10 min.
SmartMedia™, CompactFlash card, SD memory card, miniSD card, MMC, memory
stick, xD-Picture Card™
Note that inserting conversion adapters and memory cards with different functions than
above, and other memory cards (excluding the supplied wireless LAN PC card) into the
projector could damage the PC card or cause malfunctions.
Select the type of transition for slide shows from among the following
Display effect
Play icon
options using
:
None / Wipe / Wipe / Wipe / Wipe / Dissolve / Cover
Cover / Cover / Cover / Checker / Zoom / Rotate zoom /
Belt wipe / Blind
/
● Memory PC Cards Whose Operation Have Been Confirmed
Please note that presence on this list is not a guarantee of operation.
• TOSHIBA Mobile Disk: PAMHD005 (5GB), PAMHD002 (2GB)
Standard
Continuous
● Details on individual items
• SmartMedia™:
TOSHIBA PDR-SM32 (32MB), PDR-SM64 (64MB)
TOSHIBA SD-M512 (512MB), SD-M256 (256MB),
SD-M128 (128MB)
• [PC card display] function
• SD memory cards:
•
If you set PC card display to Auto., the projector switches to wireless/card input
mode automatically when a PC card is plugged into the PC card slot. Although this
item is provided as one of slideshow options, the setting works the same way even
when a wireless LAN PC card is plugged into the PC card slot.
If you set PC card display to Manual, the projector makes no response to the
plugging of a PC card into the PC card slot.
• miniSD cards:
Adapters:
TOSHIBA SD-S64 (64MB), SD-S32 (32MB)
BUFFALO MCR-5A, RXD-A
•
The TOSHIBA IPC5019A SmartMedia™ PC card adapter is not ATA-compliant, and so
cannot be used by this projector.
• [Auto. demo] function
● Backing up data
•
If you set Auto. demo to On, the projector starts a slide show automatically when it
Toshiba recommend that you back up the data on the memory PC card before use.
(Toshiba assume no liability for losses incurred by data lost through the use of this
projector.)
switches to the wireless/card input mode with a memory PC card plugged into the PC
card slot. The slide show displays the JPEG files stored in the root directory of the
memory PC card.
If you set Auto. demo to Off, a thumbnail list
p.45
•
appears automatically on the
screen when it switches to the wireless/card input mode with a memory PC card
plugged into the PC card slot. Select and view desired JPEG image files.
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting images stored in a memory PC card (Continued)
• [Interval]
■ Automatic demonstration
You can set the display interval of time (in seconds or minutes) for slide shows to be
played automatically.
p.43
If you set Auto. demo to On in “Setting slideshow options”
a slide show automatically when it switches to the wireless/card input mode with a
, the projector starts
• [Display effect]
memory PC card plugged into the PC card slot according to the procedure in
p.21
When playing a slide show, the projector can give various display effects or transitions
“Mounting a PC card”
.
to each slide being displayed.
The transitions available are listed below:
• None
Display each slide normally.
• The slide show is played as set in “Setting slideshow options”.
• The slide show displays the JPEG files stored in the root directory of the memory PC
card.
• If you set PC card display to Auto, the projector starts a slide show automatically when
the power is turned on with a memory PC card plugged.
• Wipe
Display the next slide gradually upward (Wipe ↑), downward (Wipe ↓), to the left
(Wipe ←), or to the right (Wipe →), over the current slide.
• Dissolve
• To suspend the slide show, press the
button.Pressing it again resumes the slide show.
• To end the slide show, press the RETURN button. A thumbnail list will then be displayed.
Display the next slide gradually in a certain fixed block pattern over the current slide.
• Cover
Display the next slide as sliding upward (Cover ↑), downward (Cover ↓), to the left
(Cover ←), or to the right (Cover →), over the current slide.
• Checker
Display the next slide gradually from the left using checkered blocks over the current
slide.
• Zoom/Rotate zoom
Display the next slide by enlarging it gradually, either straight from the center (Zoom)
or while turning it starting from the center (Spin zoom), over the current slide.
• Belt wipe
Display the next slide gradually in stripes from both sides, over the current slide.
• Blind
Display the next slide, as if it opened like a window blind, over the current slide.
• [Play icon]
The slideshow icon can be displayed.
• Standard
The projector handles the slideshow icon as follows depending on the “On/Off”
setting of Icon on the projector’s menu.
Icon On: The projector displays the icon upon the start of playing a slide show and
turns it off after a few seconds.
Icon Off: The projector does not display the icon.
• Continuous
The projector keeps the icon displayed during the slide show.
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting images stored in a memory PC card (Continued)
■ Playing a slide show from a thumbnail list
Searching for a target file
2
• Use the
• If there are multiple pages of thumbnails, click the
the next page, and the button on the top row to go to the previous page.
buttons to move the orange frame over the desired file or folder.
Plugging a memory PC card.
If you set Auto. demo to Off in “Setting slideshow options”
1
button on the bottom row to go to
p.43
and plug a memory
PC card into the PC card slot according to the procedure in “Mounting a PC card”
• To open a folder, move the orange frame to the desired folder and press the
You can navigate down up to 5 levels using the same procedure.
Pressing the RETURN button returns you to the next or other upper level folder.
button.
p.21
, the projector starts loading data from the PC card to display a thumbnail list on
the screen when the projector switches to the wireless/card input mode. The screenshot
below is an example of the thumbnail list. The actual list will vary depending on the data
stored on your memory PC card.
Displaying slides
3
Thumbnail list number
Current list No./Total number of lists
• Pressing the
button with a file selected displays the image in that file only in full-
Current Folder Name
screen view on the screen as a slide. Pressing the
mode.
button enters the automatic play
• To return to the thumbnail list display screen, press the RETURN button.
Operation Guide
Current File Name
Previous page exists
Changing slides
4
Orange frame: currently
selected file or folder
Pressing the
buttons with a slide displayed changes slides.
(
: previous slide; : next slide. These buttons are not available during an automatic
play.)
Folder
Thumbnail image of
first file in folder
Rotating a slide
Pressing the
5
buttons with a slide displayed rotates the slide 90 degrees. The
File
rotation information is preserved as long as you remain in the current folder.
(
: Rotate left; : Rotate right. These buttons are not available during an automatic
Thumbnail
image of file
play.)
Next page exists
Notes
Symbols in the thumbnail list
• The thumbnail display order and slide order goes in order from shortest file name to
longest. If two file names have the same number of characters, they are ordered
numerically if numbers are used in the file name, and alphabetically otherwise.
• It is possible to give presentations without using a computer by converting presentations
created with Microsoft® PowerPoint® into JPEG files using the JPEG Conversion Tool,
and storing them on a memory PC card.
Note, however, that functions such as animation effects and hyperlinks cannot be used,
so it should be tested before the actual presentation.
Indicates that only folders are
inside the folder.
Indicates that there is no data to
be displayed in the folder.
Indicates that the JPEG or other
file is not supported.
Indicates that an unsupported
JPEG or other file is present.
p.57
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the projector status
Installing the applications
If you will use the wireless LAN PC card function, install the application on the supplied
CD-ROM onto your computer.
■ Status display
To check the current status of the projector, select Status display in step 2 in
“Projector settings”
p.36
. The following items of information will then be displayed.
■ System Requirements
Supported OS:
CPU:
RAM:
Windows® 2000, Windows® XP
Pentium III 750 MHz or higher recommended
256 MB or more recommended
<Application>
The name of the application currently running on the projector is displayed.
(Examples: Slide Show, Wireless Utility)
Screen area (resolution): 1024 by 768 pixels recommended
<PC card>
When no card is plugged ➔
■ Application Types and Major Functions
“Type” is displayed.
When a memory PC card is plugged ➔
“
“
Type/Free space/Status” are displayed.
Type/MAC address/DHCP/IP address/
Wireless Utility
When a wireless LAN PC card is plugged
➔
This application is used for wireless connections. Use it to send the images from the
computer’s screen to your projector, and display on the screen.
Subnet mask/Gateway” are displayed.
JPEG Conversion Tool
Use to convert JPEG and other files into a format that can be displayed as a slide show
using a memory PC card.
<Version>
The firmware version number of the wireless/card feature is displayed.
Note
■ How to install
In the supplied CD-ROM, select the Applications folder, and run setup.exe. Follow the
instructions on your computer screen.
During the installation, a dialog box may appear with the message “Digital Signature
Not Found” and the prompt “Do you want to continue the installation?”. Click on the
[Yes (Y)] button to continue the installation.
• This product contains a piece of software (hereafter the Software) licensed to TOSHIBA
CORPORATION (hereafter TOSHIBA) by AXE, Inc. (hereafter AXE). The copyright and
other intellectual property rights of the software are held by AXE or the licensor.
The software is protected by the Copyright Law, Universal Copyright Convention, and
other intellectual property laws and agreements. The permission of AXE or the licensor
must therefore be obtained before the software can be reproduced.
Note, however, that the software is partly covered under the GNU General Public License
gpl.html. AXE will provide the GPL-covered source code of the software in accordance
with the terms of GPL2. Contact AXE if you need it.
When installation is finished, the following shortcuts will appear on your computer’s
desktop:
p.50
Wireless Utility →
Operations
p.55
JPEG Conversion Tool →
Operations
An OS of axLinux is a registered trademark of AXE, Inc.
■ How to uninstall
Select [Start Menu] → [Settings] → [Control Panel] → [Add/Remove Programs],
and remove Toshiba Data Projector from currently installed programs.
Note
• Your computer screen may temporarily go out during installation, but it is not an error.
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Wireless Utility
■ Displaying a computer’s screen via the projector
Select the screen image you wish
the projector to display.
4
Launch the Wireless Utility
software application.
1
Select Desktop
The computer screen image is transmitted as-is
.
When the Wireless Utility launches, the Screen
Image transmission mode window appears on
the computer screen.
To switch to the Screen Image transmission
mode window from another mode (File or
Projector Camera), click on the Screen Image
Select application window
Select a running application (e.g. Microsoft®
PowerPoint®), and send that application’s
window only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the computer’s
resources, which could slow communication speed.)
icon
.
Select Transmission mode.
Click on Update automatically or Update manually. See step
Update automatically and Update manually.
2
3
6
for the meanings of
Select the projector to be
transmitted.
The IDs of projectors accessible for communication
will be listed. (When a projector name is set, that
name appears instead of MAC address.) Select the
checkbox of the projector you wish to transmit to
5
Click on the Advanced button.
The Screen Image: Advanced Settings dialog
appears. Set the dialog as shown below, as
necessary.
from this list. Then icon
projector’s screen for few seconds
It is possible to select up-to four projectors.
is displayed on the
.
• Interruption
Check the No Interruptions checkbox to prevent
other computers from interrupting the projector, for
example, during presentation in the Update
automatically mode.
Click on the
button.
6
7
When “Update automatically” is selected in step
Screen images are sent consecutively after the
When “Update manually” is selected in step
2
• Window
button is clicked.
Select the Place in Tasktray at the start of
transmission checkbox to iconify the Wireless
Utility and place it in the computer’s tasktray
when transmission initiated.
To display the window, double click on this icon, or
right click and select Open from the popup menu.
Even with the Wireless Utility window minimized,
you can use the pop-up menu to stop or resume
2
A single screen image is sent when the
button is clicked.
To halt transmission from Update automatically, click on the
button.
If the Wireless Utility icon has been placed in the tasktray, double click on the icon to
display the window, then halt transmission, or right click on the icon, and halt transmission
.
transmission as described in step
• Mode
Selecting High quality improves the quality of the
projected image, but lowers communication
speed. Selecting High speed has the opposite
effect.
and later
4
Notes
•
It may not be possible to transmit the images from movie player or other video applications
• When using “Update automatically”, the transmitted image refresh rate depends on the
performance of the computer you are using and the surrounding radio wave environment.
• The projector screen may have a few differences from the computer screen.
It is not possible to transmit to a projector that is already receiving from another computer
.
•
.
• If you selected application window in step , if that application is not active (in use), the
4
image may not be correctly displayed by the projector.
• The projector ID is the MAC address of the wireless LAN PC card inserted into the
projector.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Wireless Utility (Continued)
■
Displaying a JPEG image saved on a computer via the projector
Select the projector to be
transmitted.
5
6
Launch the Wireless Utility software application.
The Screen Image transmission mode window appears on the computer’s screen.
1
The IDs of projectors accessible for
communication will be listed. (If projector name
has been set up already, it is shown instead of
the MAC address.) Select the checkbox of the
projector to be transmitted to from this list.
Click on the File icon
.
2
The Wireless Utility
window changes to File
transmission mode.
Then icon
is displayed on the projector’s
screen for few seconds.
It is possible to select up-to four projectors.
Click on the
button.
The selected file’s image is displayed by the projector.
Note
Click on the Browse button, and
select the file to send.
Clicking on the Browse button displays the Open
dialog box. Select the file to send, then click on
the Open button.
3
4
•
Only one file can be sent at a time. To send another file, repeat steps
4
and
6
.
■ Operating the projector
This function can be used with any projector input.
Note, however, that this will not function with a memory PC card.
The selected file is added to the pull-down list in
the Wireless Utility’s Transmission File field.
Launch the Wireless Utility software application.
The Screen Image transmission mode window appears on the computer’s screen.
1
2
Select the file to be sent from the
pull-down list of the Transmission
File field.
Click on the Remote
Control button.
The Remote Control window
appears.
Click on the Transmission File field’s
button to
display the pull-down list. Select the file to be sent
from this list.
A thumbnail of the selected file appears in the
Preview box. The file displayed here will be
transmitted.
As the Wireless Utility window is
still displayed, you can operate the
projector via the Remote Control
window, while using the Wireless
Utility’s functions.
Step
3
can be skipped.
The way that drag and drop the file to be sent from the desktop or Windows Explorer
into the Preview box is also available. In this case as well, the selected file is added to
the file pull-down list Transmission File field’s.
While it is possible to use this function merely to operate the projector, closing the
Wireless Utility also closes the Remote Control window.
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Wireless Utility (Continued)
How to use the JPEG Conversion Tool
The JPEG Conversion Tool converts JPEG files not supported by the projector, image
files in other formats, Microsoft® PowerPoint® files, and the like into JPEG files supported by
the projector. The JPEG files converted with this tool can be displayed by sending them
Select the projector to be operated.
3
In the Remote Control window, click on the
button, and
select the desired projector from the pull-down list. The remote
control screen will then change to the new one as shown on the
right. Only one projector can be selected. (It is not possible to
operate multiple projectors.)
p.52
p.42
using the wireless LAN PC card
, or saving them on a memory PC card
.
■ Launching the JPEG Conversion Tool
The window shown in the figure to the right appears on the
computer screen.
Drag the Image Quality Settings slider to the left or right to set the
image quality of the file after conversion. Lower values create
smaller files, but lower the image quality. (It is not possible to restore
the quality of an image after it has been lowered.)
■ Converting an image file
This converts JPEG files using compression formats not supported by the projector,
Windows® metafiles (wmf), and bitmapped files (bmp) into JPEG files.
(1) In the Conversion Method field, select Converting image
file. (Status on launch)
(2) In the File settings field, click on the Browse button for
Original Image File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(1)
Click on the Remote Control window’s buttons.
The function of each button and box is as follows:
Power On: Turns projector power on.
Power Off: Turns projector power off.
4
5
(2)
(5)
Input (box) : Click on the
button, and select the desired input from the pull-down
(a) Specify the location of the file to be converted; and
list.
(b) In the Files of Type field, click on the
the file format. A list of files of that format appear in the
Open dialog box.
button to select
Go:
Switches to the input selected in the Input box.
Freeze:
Mute:
+/–:
The picture is paused.
Cuts off picture and sound. Click again to restore picture and sound.
Adjust sound volume.
(7)-(a)
(4) In the Open dialog box, select the file to convert, then click
on the Open button.
(5) In the JPEG Conversion Tool window, in the File
settings field, select Browse for File name after
conversion. The Save As dialog box appears.
(6) In the Save As dialog box:
(3)-(a)
To quit, click on the
window.
button on the Remote Control
(4)
(3)-(b)
Performing this does not close the Wireless Utility window.
To exit both the Wireless Utility and the Remote Control, click on the
the Wireless Utility window.
(a) Specify the location in which to save the converted
file;
(b) Enter a file name of up to 8 characters in the File
Name field; and
button on
Note
(c) Press the Save button.
(6)-(a)
p.39
(7) (a) In the JPEG Conversion Tool, click on the
Conversion button.
•
Remote control's functions can be restricted by setting Remote control
.
(6)-(b)
(6)-(c)
(b) A confirmation dialog box opens. Click Yes.
The computer converts the file. When it finishes a
message appears informing you that a JPEG file
has been created.
■ Document camera function
The document camera function is available for the Toshiba LCD data projector TLP-T701/
T721/T501/T521/T521E.
For details, consult your local dealer.
(7)-(b)
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the JPEG Conversion Tool (Continued)
■ Converting files created with Microsoft® PowerPoint®
■ Making a presentation with converted JPEG files
This process provides presentations without using a computer by converting
presentation files created with Microsoft® PowerPoint® into JPEG files, storing them on
a memory PC card, and displaying them in a slide show.
• To use this conversion mode, Microsoft® PowerPoint® must be installed on the
(1) Copy the folder created by the JPEG Conversion Tool, or its contents, onto a
memory PC card.
p.46
(2) Use the step
1
in “Playing a slide show from a thumbnail list”
to display a
list of thumbnails.
computer.
(3) Follow the instructions in step
2
in “Playing a slide show from a thumbnail list”
• Only static images are supported by this process. Animation and audio are not
supported.
Presentation files created with Microsoft® PowerPoint® usually
consist of several slides. For this reason, the tool creates a folder
with the name specified in step (5), below, and file for each slide
is created in the folder (starting with slide001.jpg).
p.47
to find the thumbnail of the first slide, Slide001.jpg, and move the orange
frame to it. (Select Slide001.jpg.)
(4) Press the
button on the remote control. An enlarged view of the first slide
appears on the screen. This starts the presentation.
(1)
(5) To continue to the next slide, press the remote control’s
previous slide, press the button.
button. To go back to the
(2)
(1) In the Conversion Method field, select Converting PPT
file.
(4)
■ Creating a screen capture and converting it into a JPEG file
(2) In the File settings field, click on the Browse button for PPT
File Name.
This function saves the current computer screen as a JPEG file.
The Open dialog box appears.
(1) In the Conversion Method field, select Creating screen
(9)-(a)
capture.
(3) In the Open dialog box:
(1)
(a) Specify the location of the file to be converted; and
(b) Select the PowerPoint® presentation file to convert,
then click on the Open button.
(2) In the File settings field, click on the Browse button for File
name after conversion.
The Save As dialog box appears.
(3)-(a)
(2)
(4) In the JPEG Conversion Tool window, in the File
settings field, click on the Create button for New
folder name.
(3) In the Save As dialog box:
(3)-(b)
(5)
(a) Specify the location in which to save the converted file;
(b) Enter a file name of up to 8 characters in the File Name
field; and
(c) Click on the Save button.
The Folder create dialog box appears.
(4)-(a)
(5) In the Folder create dialog box, in the Folder Name of
(6)
document field, specify a folder name of 12 characters or less.
(4) (a) In the JPEG Conversion Tool window, click on the
Conversion button.
(b) A confirmation message appears. Click Yes.
(8)-(a)
(6) In the Folder create dialog box, click on the Selection button.
(3)-(a)
The Browse for Folder dialog box appears.
The computer creates a screen capture, and
(7) In the Browse for Folder dialog box:
(a) Specify the location in which to save the folder; and
(b) Click on the OK button.
(3)-(b)
(3)-(c)
converts it into a JPEG file in the specified location.
When it is finished, a message appears to tell you
that a JPEG file has been created.
(7)-(a)
(8) In the Folder create dialog box:
(a) Click on the Create button.
A confirmation dialog box appears;
(b) Click on the OK button.
(7)-(b)
(8)-(b)
(4)-(b)
Note
(9) (a) In the JPEG Conversion Tool window, click on the
Conversion button.
•
The maximum resolution of JPEG files created with the JPEG Conversion Tool is 1,024 ×
768 pixels.
(b) A confirmation dialog box opens. Click Yes.
The computer begins to convert the file. When it finishes,
a message appears informing you that a JPEG file has
been created.
(9)-(b)
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the projector using a Web browser
■ How to use the “Projector Configuration Tool”
Select items from the menu on the left.
4
The “Projector Configuration Tool” uses the Web server features of the projector to
set up the projector using a wireless LAN PC card.
When using the “Projector Configuration Tool”, set up the wireless LAN connecting
the projector and the computer.
Setting:
Allows you to make various settings on the wireless/card
menu. When Browser authentication has been set to On,
access to the setup page requires the input of the password.
Displays some states of the projector.
Introduces the functions available in wireless/card input
mode.
Status Display:
Features:
p.48
See “Checking the projector status”
to display
1
Projector name:
Enter a character string and press the Set button, and it will
be set as the projector name.
information on the screen and write down the IP address.
Top:
Returns you to the top page.
TOSHIBA Projector Site
:
The browser will display the home page at http://
multimedia.projector-toshiba.com/map.html, providing
projector information. The home page address is subject to
change without notice.
(The Toshiba’s web site can be browsed only when your
computer can access the Internet.)
Invoke Internet Explorer.
Internet Explorer Ver. 5.0 or later is recommended. Enable the Javascript functions.
2
3
In the address bar, enter the IP address
The Web browser will then display the following page.
above.
1
● Details on major items
• Setting
Allows you to make various settings on the wireless/card menu. When Browser authentication
has been set to On, access to the setup page requires the input of the password.
Menu
Network:
The items available here are equivalent to those in the wireless/card
menu. Note, however, that security items such as “Remote control” and
“Browser authentication” cannot be set. Entering individual items and
press the Execute button to update their setting.
Projector name
Projector ID
Enter the projector
name to be registered.
Slide Show: The items available here are equivalent to those in the wireless/card
menu. Entering individual items and press the Execute button to update
their setting.
Projector name Projector ID
Note 1: To prevent access from third parties, the projector is restricted to permit access
only from the computer that has been set up for the TCP/IP to have the same
network address as the projector.
Note 2: If you use a proxy server, do not enable the proxy when accessing the above IP
address.
The TCP/IP settings for the projector and computer are required even in the
wireless LAN Ad hoc mode.
Press this button after entering
the password.
Discards what you have entered.
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the projector using a Web browser (Continued)
• Features
Introduces the functions available in Wireless/Card input mode.
Slide Show
Wireless Utility
Displays the
Help page.
Updates the
settings.
Discards what
you have
entered.
Enter single-byte alphanumeric characters in text input fields.
• Status Display
Displays some states of the projector.
Projector:
Displays the contents of status display in the menu.
Wireless/Card: Displays the contents of status display in the Wireless/Card menu.
Maintenance: Describes an error if it occurs, for example, when the lamp has blown.
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
• The lamp may explode with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
• How long it takes before the lamp explodes or the life expires may vary greatly by lamp.
Some may explode shortly after first use. (Free replacement is available if the lamp
explodes within the warranty period. Contact the dealer from whom you purchased the
product in such a case.)
Unplug power cord.
1
2
Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
3
Remove the lamp cover.
3
Lamp cover
1
Loosen the 1 screw, then pull up to the direc-
tion of the arrow with your fingers as shown to
remove the lamp cover. Use care to avoid any
damage to nails and/or tip of your finger(s). (If
you have any difficulty in removal, you can use
a screwdriver or any other smaller tool for your
convenience.)
•
Explosion is likely to happen if the lamp is used after the replacement period has elapsed.
• When the lamp explodes, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
• When the lamp explodes, a slight amount of mercury gas enclosed in the lamp along
with glass dust may be released from the openings for ventilation.
2
■
Immediately replace the lamp when a sign appears on the screen.
• When the replacement time approaches, a message will appear on the screen.
Pull out the lamp.
Loosen the 2 screws holding the lamp in place,
and pull up the handle to remove the lamp.
4
5
1
•
The risk of explosion will increase if the lamp is continuously used without being replaced.
4
5
• Frequently check the used hours and prepare spares when the replacement time
p.33
approaches. (Refer to “Status display”.
)
2
■
When the lamp is broken
Mount the new lamp.
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp explosion, unplug the product from the wall outlet, leave and
completely ventilate the room. Then, thoroughly clean the area around the projector and
discard any edible items placed in that area.
2
Replace the lamp cover.
Align the cover, and press it in, then tighten the
6
7
• When the lamp explodes, consult a doctor if glass dust or mercury gas gets into your
eyes or you breathe it.
1
3
screws loosened in step
no longer loose.
until the lamp cover is
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one
.
Notes and Precautions
WARNING
p.33
• Lamp time in the Status display menu indicates lamp uptime (reference value)
• It is recommended that the lamp be replaced after 2,000 hours of use. When Lamp time
reaches 2,000 hours, the icon and a message will appear. This display disappears
when you press button.
.
•
If the projector is mounted on a ceiling, request a lamp replacement from your projector dealership.
• When replacing, always use lamp “TLPLW5” (sold separately).
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
CAUTION
p.65
lamp may fail to come on
, and the lamp’s lifetime may be shortened.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
•
•
If you have been using the projector, the lamp will be very hot, and may cause burn injuries
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.
.
62
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Lamp replacement (Continued)
Trouble indications
The indicator lights inform you of internal abnormalities.
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
No power
⇒ Problem with projector
• Unplug the power cord, and contact your dealer.
⇒ The lamp cover is not properly attached.
p.63
• Unplug the power cord, and reattach the lamp cover.
(Off)
Lens and main unit cleaning
Lamp went out during use, or won’t come on
⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of
the lamp has ended or the projector is malfunctioning.
(Red lit)
•
Unplug the power cord and wait for a short while, then turn the power back on.
WARNING
• If a lamp burns out, replace it with a new one.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
•
Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.
(Red lit)
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop
down, thus resulting in injury.
Power went out during use
⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
(Red lit or flashing)
Or (Orange lit)
(Green lit)
■ Lens cleaning
•
Unplug the power cord and wait for a short while, then turn the power back on.
• Clean the lens with a commercially available blower and/or
❈ The icon will appear before the power goes out.
❈ After approx. one minute of abnormal display, the projector returns to
lens cleaner.
(Red lit)
the standby state waiting for internal cool down.
• The lens is easily scratched, so do not rub it with hard objects,
or strike it.
Power went out during use
⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
(Red lit or flashing)
Or (Orange lit)
■ Main unit cleaning
❈ The
icon will appear before the power goes out.
• Clean the main unit after unplugging the power cord.
• Wipe dirt off the main unit gently with a soft cloth.
• If the soiling is severe, dip the cloth in a neutral
detergent diluted in water, wring well, and gently wipe
off the dirt, then finish up by wiping with a dry cloth.
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Red lit)
Power went out during use
⇒ Problem inside the projector.
(Green lit
or Off)
•
Unplug the power cord and wait for a short while, then turn the power back on.
(Green lit
or Off)
(Green
flashing)
• If the above action will not clear the problem, unplug the power cord,
and contact your dealer.
● Replacing cooling fans
❈ After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Red lit)
To maintain the performance, it is recommended that cooling fans should be replaced
about every 2 to 3 years. Consult with your dealer for details.
PRECAUTION
• Make sure to unplug the power cord if something goes wrong.
64
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
If This Happens
Check
p.65
Please see “Trouble indications”
as well.
• Is the memory PC card inserted correctly?
Memory PC card
images aren't
projected
p.42
If This Happens
Check
• Is a PC card not supported by the projector inserted?
p.21
• Is the CARD indicator red?
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover loose?
No power
• Are there any JPEG files saved on the memory PC card?
• Are the files too large or in an unsupported format for the projector?
Convert them with the supplied software application.
p.63
p.65
• Is the ambient temperature high?
Power goes out
during use
p.55
p.65
• Is the air intake or air exhaust blocked?
• Is the wireless LAN PC card inserted correctly?
• Is a wireless LAN PC card not supported by the projector inserted?
The operation of cards other than the supplied product is not
guaranteed.
The wireless
LAN PC card
doesn't work
p.24
• Is the projector turned on?
• Is the mute function on?
No picture
p.28
p.30
• Is the brightness setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
p.20
p.21
• Is the CARD indicator red?
• Are the transmission mode and channel properly configured?
p.38
p.24
• Is the projector turned on?
• Is the mute function on?
No audio
• Are there any obstructions between the computer and projector?
• Do your computer and OS support the supplied software
p.28
p.25
p.49
• Is the volume setting minimized?
• Are the connections set up correctly?
application?
p.20
• Are all the connected devices functioning properly?
p.69 p.70
• Is the input signal supported by the projector?
,
Picture not
displayed
correctly
• Is there something generating an abnormal video signal, for
instance the video tape?
p.64
• Is the lens dirty?
Picture blurred
Part of picture
out of focus
p.25
• Is the lens focus adjusted optimally?
• Is the projection distance within the projector’s supported range?
p.19
p.19
• Is the projector’s screen placement angle tilted too far?
p.27 p.30
• Are the sharpness or sampling phase adjustments off?
p.30
• Are the brightness or contrast adjustments off?
• Is the lamp nearing the end of its service life?
Image is dark
p.33
p.30
• Are the color, tint, R-level, G-level, or B-level adjustments off?
• Is the screen dirty?
• Is the lamp nearing the end of its service life?
Colors too light
Bad shading
p.33
• Are the remote control’s batteries drained?
Remote control
doesn’t work
p.18
• Are the batteries inserted into the remote control correctly?
• Is the remote control being used within the effective range?
• Are there any obstructions between the remote control and
projector?
p.18
• Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
66
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
■ List of general specifications
■ List of supported signals (RGB signals)
This projector supports the following RGB signals. Note, however, that depending on the
Item
Specification
computer model, the screen may show flicker or streaking. Please adjust the projector if
Consumption Power
Weight
External Dimensions
(including protruding parts)
Cabinet material*
270 W
2.9 kg
this happens.
p.26 p.27
(Press the SET UP button, and adjust automatically or manually.
,
)
298 × 101.4 × 275.4 mm (W × H × D)
Refresh rate
(Hz)
H-frequency
Clock
(MHz)
PC+ABS resin and ABS resin
Resolution
Mode
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%
720 ⋅ 400
640 ⋅ 480
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16"
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
Display pixels
Picture elements
Lens
1 chip DMD™
480,000 pixels (800H × 600V)
Zoom lens
High-pressure mercury lamp
24.6-246 inches
1.20-10.00 m
F=2.6-2.81 f=22.34-26.8 mm
Lamp
Projection screen size
Projection distance
Speaker
800 ⋅ 600
1 W (Monaural)
COMPUTER-1 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)
COMPUTER-2 terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)
MONITOR terminal
S-VIDEO terminal
AUDIO (L/R) terminal
VIDEO terminal
Mini D sub 15 pin RGB / Y/PB/PR (dual use)
Mini DIN 4 pin
RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more
RCA Pin Jack, 1 V (p-p), 75 Ω
ø3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more
ø3.5mm dia. stereo mini-jack
Mini DIN 8 pin (RS-232C)
832 ⋅ 624
1024 ⋅ 768
XGA_60
XGA_70
XGA_75
XGA_85
AUDIO IN terminal
AUDIO OUT terminal
CONTROL terminal
PC card slot
MAC19"
1152 ⋅ 864
1280 ⋅ 960
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
Compliant with PC Card Standard TYPE II
* Each plastic part displays the materials it is made from, in order to facilitate recycling after this
product becomes no longer usable.
1280 ⋅ 1024
■ Separately sold product
1400 ⋅ 1050
1600 ⋅ 1200
Replacement Lamp
Model TLPLW5
Note
• Design, specifications, etc. subject to change without notice for improvements, etc.
Note
• Signals which resolution exceeds the native resolution (800 × 600 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
68
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
■ List of supported signals (Y/PB/PR signals)
■ CONTROL terminal
Signal format
fh(kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
33.75
31.25
fv(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60.00
50.00
● Pin assignment
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1035i(1125i)@60Hz
1152i(1250i)@50Hz
Pin No.
Signal Name
RXD
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
1
2
3
4
5
6
7
8
7
CTS
DSR
GND
RTS
N.C
TXD
GND
8
6
5
3
4
2
1
Signal ground
Mini DIN 8 pin connector
● Interface format
1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
■ List of supported signals (Video, S-Video signals)
Stop Bit Length: 1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Video mode
NTSC
fh(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
fv(Hz)
60
fsc(MHz)
3.58
2 Communication format
3 Data format
PAL
50
4.43
SECAM
PAL-M
50
4.25 or 4.41
3.58
60
4 Replies
Acknowledge
ACK (06h) CR (0Dh) Data ... Normally ended
PAL-N
50
3.58
ACK (06h) ESC (1Bh)
NAK (15h)
... Aborted
PAL-60
NTSC4.43
60
4.43
60
4.43
No acknowledge
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
■ Pin assignment of COMPUTER-1/2 & MONITOR terminals
● Main Commands
Pin
No.
1
Pin description
During Y/PB/PR input
5
1
Item
Command
IN1
Item
Command
PON
During RGB input
Video signal (R)
Video signal (G)
Video signal (B)
GND
Computer (1) input select
Computer (2) input select
Video input select
Power on
Power off
Icon display on
Color difference signal (PR
)
IN2
IN3
POF
MO0
2
Luminance signal (Y)
3
Color difference signal (PB)
S-video input select
PC card input select
IN4
IN5
Icon display off
MO1
PAT
4
∗
∗
10
15
6
Auto setting (RGB input)
Status display on
Status display off
5
GND
11
DON
DOF
6
GND (R)
GND (PR
)
Mini D sub 15 Pin connector
7
GND (G)
GND (Y)
8
GND (B)
GND (PB)
Input Signal
• RGB input
RGB signals:
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/PB/PR input
Note
9
N.C
∗
∗
∗
∗
∗
∗
∗
• Contact your dealer for control cable and other commands.
10
11
12
13
14
15
GND
0.7V (p-p) 75 Ω
GND
N.C
Horizontal sync signal
Vertical sync signal
N.C
Y signal:
PB/PR signals:
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
∗ Do not connect anything.
70
71
Download from Www.Somanuals.com. All Manuals Search And Download.
|