SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN
THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING: Handling the cord on this product or cords associated with accessories sold
with this product, will expose you to lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. Wash hands
after handling.
USA only
WARNING: This [product] contains mercury. Disposal of mercury may be regulated due
to environmental considerations. For disposal or recycling information, please
org.
USA only
USA only
TRADE NAME: DATA PROJECTOR
MODEL NAME: TDP-P8
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use
can result in electric shock or fire hazard. The safeguards incorporated in this unit will
protect you if you observe the following procedures for installation, use and servicing. This
unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owner’s Manual
3. Source of Light
After unpacking this product, read
the owner’s manual carefully, and
follow all the operating and other
lamp is on. The strong light from
the lamp may cause damage to
your eyes or sight.
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type
of power supply to your home,
consult your product dealer or
local power company.
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface. This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or the
manufacturer’s instructions have
been adhered to.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Heat
8
Power-Cord Protection
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
amplifiers) that produce heat.
6
Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
9. Overloading
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as
this can result in a risk of fire or
electric shock.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
10 Lightning storms
12 Do not place the product
vertically
For added protection for this
product during storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
However, while it is thundering
or lightning, do not touch the
apparatus and any connected
cable and/or equipment. This will
prevent you from receiving the
electric shock by an electric surge.
Do not use the product in the
upright position to project the
pictures at the ceiling, or any
other vertical positions. It may fall
down and dangerous.
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
11. Object and Liquid Entry
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
e) If the product has been dropped
or damaged in any way.
15 Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces
f) When the product exhibits a
distinct change in performance -
this indicates a need for service.
17 If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
may cause the product and cart
combination to overturn.
This product incorporates glass
components, including a lens and
a lamp. If such parts should break,
please handle with care to avoid
injury and contact your dealer for
repair service. The broken pieces
of glass may cause to injury. In
the unlikely event of the lamp
rupturing, thoroughly clean the
area around the projector and
discard any edible items placed in
that area.
S3125A
16. Damage Requiring Service
Unplug this product from the
wall outlet and refer servicing to
qualified service personnel under
the following conditions:
18. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed
to rain or water.
d) If the product does not operate
normally by following the
operating instructions. Adjust only
those controls that are covered
by the operating instructions as
an improper adjustment of other
controls may result in damage
and will often require extensive
work by a qualified technician to
restore the product to its normal
operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
19 Replacement Parts
22 Do not use the product in
a closed installation state.
Do not place the product in a box
or in any other closed installation
state. Otherwise it may overheat.
This could result in a risk of fire.
When replacement parts
are required, be sure the
service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
23 Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person
or a mirror.
(Replacement of the lamp only
should be made by users.)
The laser beam may cause
damage to the eyes or sight.
20. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to determine that
the product is in proper operating
condition.
21 Do not leave thermalpaper
documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods
of time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.
Plug
Plug
configuration Plug type
Line voltage
220 240V
configuration Plug type
Line voltage
200 240V
Australian
240V
10A
EURO
Switzerland 200 240V
240V
6A
UK
220 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
200 240V
240V
15A
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. To prevent the unit from possible damage, do not use
the unit for at least 2 hours when there is an extreme or sudden change in temperature.
• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
• Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to
use it in that situation, the malfunction may result. Ensure to wait until the condensation
naturally disappears.
• In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High]
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS (Continued)
• The set of projector is hot after use. Handle with care.
• Do not use the projector while holding it in your hands or lap.
• Do not use the projector near a power source and the like, or in locations like a ship
or vehicle that are subject to vibration or shock. Doing so may lead to a malfunction or
shorten service life.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the product’s precautions.
EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
Model No.
Serial No.
Retain this information for future reference.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER CAUTIONS AND INFORMATIONS
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad
casting programs with the purpose of other than the personal and private viewing,
including modifying images using the freeze, resize, PIP, or SPLIT screen functions, or
displaying with the varying aspect ratio of the images, could violate the direct or indirect
copyrights of the imaging software or broadcast program, etc., if done without first
consulting with the copyright holder. For this reason, please take appropriate measures
before performing one of the actions listed above, including obtaining a license from the
copyright holder.
Disposal
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
This product contains substances which are harmful to humans and the environment.
• The lamp contains inorganic mercury.
Please dispose of this product or used lamps in accordance with local regulations.
• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.
• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas
Instruments.
• Macintosh is a registered trademark of Apple Computer, Inc.
• Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems
Incorporated.
References to pages with related information are annotated as follows.
For example, if making a reference to page 35:
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BATTERIES
• Never throw batteries into a fire.
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of battery disposal.
• Do not mix different battery types or combine used batteries with new ones.
• If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.
• If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
Using the batteries improperly may cause them to explode or leak and lead to burn or
injury. If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water
and consult a doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using
tissue paper.
(Dispose of the used tissue paper as flammable garbage after moistening with water.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents.......................................................................................13
Introduction ................................................................................................14
Package Overview .............................................................................................14
Product Overview...............................................................................................15
Main Unit......................................................................................................................15
Control Panel ...............................................................................................................16
Connection Ports .........................................................................................................17
User Controls .............................................................................................18
Control Panel & Remote Control........................................................................18
Preparing and using the remote control .............................................................20
Operating a computer using the remote control.................................................22
Installation..................................................................................................23
Connecting the Projector....................................................................................23
Turning the power on and off .............................................................................24
Connecting the power cord..........................................................................................24
Removing the lens cover .............................................................................................24
Turning the power on Press the ON / STANDBY button .............................................24
Turning the power off...................................................................................................25
Adjusting the Projested Image ...........................................................................26
Adjusting the Projector Image Height ..........................................................................26
Adjusting the Projector Zoom / Focus..........................................................................27
Adjusting Projection Image Size ..................................................................................27
Adjusting the screen size and focus ............................................................................28
Using the menus ........................................................................................29
How to use the menus........................................................................................29
The image adjustment menu..............................................................................30
The display setting menu ...................................................................................31
The default setting menu....................................................................................32
Manual adjustments and settings.......................................................................33
Displaying Information (Status display)..............................................................34
Appendices ................................................................................................35
Trouble shooting.................................................................................................35
Replacing the lamp.............................................................................................38
Computer Compatibility (Analog) .......................................................................40
Specifications .....................................................................................................41
About Lamp................................................................................................42
About Lamp........................................................................................................42
Immediately replace the lamp when a sign appears on the screen ...................42
When the lamp is broken....................................................................................42
Lamp replacement..............................................................................................43
Lens cleaning .....................................................................................................43
Main unit cleaning ..............................................................................................43
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Package Overview
This projector comes with all the items shown below.
Check to make sure your unit is complete. Contact your
dealer immediately if anything is missing.
Projector with lens cap
Power Cord 3m
VGA Cable 3m
USB Cable 3m
Remote mouse Control
with Laser Pointer
Owner’s Guide
The shape and
number of supplied
power cords vary
depending on the
product destination.
AAA battery for mouse
remote control(2)
Carrying Case
Owner’s Manual
The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual, including information not available for
the printed Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.
Installing Acrobat®
Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.
Follow the on-screen instructions.
Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader
Installer. Follow the on-screen instructions to install the software.
Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the
menu screen of the Owner’s manual appears. Click on your language. The Owner’s
Manual cover appear.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction (Continued)
Product Overview
8
Main Unit
1
2
3
7
4
6
5
1
8
10
9
1. Control Panel (See page 16 for detailed information.)
2. Zoom Lever
3. Focus Ring
4. Projection lens
5. Lens Cap
6. Foot adjuster
7. Front foot adjuster release button
8. Infrared remote sensor
9. Rear panel (Connection external devices.)
10. AC IN socket
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction (Continued)
Control Panel
2
3
1
6
5
4
7
1. Temp Indicator LED (Refer to page 37 for more information.)
2. On indicator light(Refer to page 37 for more information.)
3. LAMP indicator(Refer to page 37 for more information.)
Indicates the status of the lamp has developed a problem.
4. ON/STANBY button (Refer to page 24 for more information.)
Turns the projector on or off.
5. MENU button Open,saves and exits the on-screen menu.
,
,
6.
,
, button The directional buttons are used to
select the desired menu items and to make adjustments when
the onscreen menu is activated. Refer to page 18 for more
information.
7. ENTER button : Accepts the selected mode.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction (Continued)
Connection Ports
1
7
6
5
4
3
2
1. Infrared remote sensor
2. AC IN socket(Connect the supplied power cord here.)
B
R
3. COMPUTER (Y/P /P ) IN terminal
RGB : Input analog RGB signal from a computer or other
source, or a component video signal (Y/P /P ) from video
B
R
equipment.
4. Video IN terminal
5. S-Video IN terminal
6. USB terminal (for remote mouse control)
7. Antitheft lock hole
(Attach a safety cable or any other antitheft device.)
The projector is a moveable equipment
17
Download from Www.Somanuals.com. All Manuals Search And Download.
User Controls
Control Panel & Remote Control
There are two ways for you to control the functions: Re-
mote Control and Control Panel.
Control Panel
Remote Control
Using the Control Panel
On / Standby
Refer to the “Power On/Off the Projector” section on page 24.
Input
Press “Input” to choose RGB, Component-p, Component-i, S-Vid-
eo, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on screen display (OSD) menu. To
exit OSD, press “Menu” again.
/
Keystone +/-
Adjusts image distortion caused by tilting the projector (±15 de-
grees).
Enter
Confirm your selection of items.
Auto Set
Automatically synchronizes the projector to the input source.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
User Controls (Continued)
Rear
Front
Remote control transmitter
Laser emitte
(5)
Mouse remote control receiver
CAUTION Label (LASER)
(8)
(15)
(12)
(11)
(7)
(9)
(10)
(1)
(3)
Remote Control
(6)
(2)
(13)
(4)
(14)
Battery
cover
LASER WARNING
Control
button cover
CAUTION Label (LASER)
CAUTION Label
(LASER)
Name
: Main Function
: Accepts the selected mode.
: Displays menus.
(1) ENTER button
(2) MENU button
(3) Set up
: Set up image and mode.
(4) ON/STANDBY button
(5) Transmission indicator
(6) INPUT button
(7) ESC
(8) Selection button
(9) LASER button
(10) button
: Turns the power on/off (standby).
: Lights when remote control transmitting.
: Selects input.
: Quit the current screen.
: Menu selections and adjustments,etc.
: Displays laser point.
: This control functions as a computer’s button.
(11) button
: This control functions as a computer’s
: Switches remote control mode.
: Pauses image.
: Cuts off the picture.
: Left button click of remote control mouse.
button.
(12) PJ MODE button
(13) FREEZE button
(14) MUTE button
(15) L-CLICK button
19
Download from Www.Somanuals.com. All Manuals Search And Download.
User Controls (Continued)
Preparing and using the remote control
Loading dry-cell batteries into
the remote control
1. Remove the battery cover.
Operating the remote control
Point the remote control toward the
projectorfs infrared remote sensor, and
press a button on the remote control.
• Operating the projector from the front
2. Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
• Operating the projector from the rear
3. Replace the battery cover.
Dry-cell batteries
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the
batteries with new ones.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to
bright sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control.
If this happens, point the remote control at the main unit again, and repeat the
operation.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
User Controls (Continued)
Preparing and using the remote control (Continued)
Switching operation mode
Operation modes should be switched between projector operation and computer
operation.
Switching the remote control operation mode.
Pressing this button toggles the mode.
When this button is lit, the remote control is in [PJ Mode]
(Projector operation mode).
If no operations are made for 30 seconds, this light goes
out, and the remote switches back to [PC Mode] (Computer
operation mode).
[PJ Mode] : Functions as a select button.
If no menu is displayed, operate “INPUT” ,“KEYSTONE” ,
“AUTO SET” button
[PC Mode] : Functions as a mouse pointer control.
Pressing displays a laser pointer, regardless of the mode.
[PC Mode] : Functions as a down button. Used to go
forward on Microsoft® PowerPoint® slides, etc.
[PC Mode] : Functions as an up button. Used to go back
on Microsoft® PowerPoint® slides, etc.
[PC Mode] : Functions as the right mouse button (R-CLICK).
[PC Mode] : Functions as a ESC button.
Pressing one of these buttons automatically sets the
remote control to [PJ Mode].
If no operations are made for 30 seconds, and the remote
switches back to [PC Mode].
The L-CLICK (left click) button on the back of the remote
control functions when in [PC Mode].
Notes
• With the exception of operating a PC with the remote control, all buttons are used in
[PJ Mode].
• Make sure there is nothing between the remote control and the IR sensor on the
projector that might obstruct the infrared beam.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
User Controls (Continued)
Operating a computer using the remote control
A computer can be operated using the projector’s remote control. This function
is available on any computer with the Windows 98/98SE, Windows Me, Windows
2000, or Windows XP OS, that is equipped with a USB port supporting the USB 1.1
(The mouse remote control is supported on OS 9 or OS X for the Macintosh). The
operation cannot be guaranteed for all the environments of computers.
Connecting a computer
1
Connect the supplied USB cable to the computer.
Operating a computer
2
The mouse remote control function is available when the remote control is set to [PC
Mode]. (See “Switching operation modes”.) Point the Mouse remote control at the
mouse remote control receiver, and operate the remote controlfs buttons.
•
Moving the mouse pointer
Move the pointer control button in the direction that you wish the mouse
pointer to move, then press.
•
•
•
To left click
Press the L-CLICK button.
To right click
Press the R-CLICK button.
To drag and drop
Move the pointer control button in a (L-)clicked state, then when the pointer is
over the desired location, release the button.
Using the computer’s up and down arrow key functions
Press the and buttons to switch PowerPoint® slides.
•
Remote Control Front
Remote Control Rear
Pointer control
L-CLICK
R-CLICK
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the Projector
USB
RGB
4
DVD Player,
Settop Box,
HDTV receiver
2
6
5
3
1
S-Video Output
Video Output
Due to the differ-
ence in applications
for each country,
some regions may
have different ac-
cessories.
1. ..................................................................................................Power Cord
2. ...................................................................................................VGA Cable
3. ........................................................................... Video Cable(not supplied)
4. ...................................................... D-sub15p to YPbPr cable(not supplied)
5. ...................................................................... S-VIDEO cable(not supplied)
6. ....................................................................................................USB cable
To ensure the projector works well with your computer,
please set the display mode of your graphic card less than or
equal to 1024 X 768 resolution. Make sure the timing of the dis-
play mode is compatible with the projector. Refer to the “Com-
patibility Modes” section on page 40.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
Turning the power on and off
Connecting the power cord
Insert the power cord connector into the
AC IN socket of the projector.
Insert the power cord plug into a wall or
other power outlet.
Power
conne
(Supp
Removing the lens cover
Be sure to remove the lens cover when the power is turned
on. If it is left on, it could become deformed due to heat.
Turning the power on
Remote
Control
Control panel
Start-up screen
The power turns on, and green
indicators light: POWER.
After a moment, the start-up screen
appears.
Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
• The first time you use the projector after purchase, after the start-up screen, please press
“MENU” button.
Turning the power off
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
Press the ON/STANDBY button again.
If the screen turns off, but the internal cooling fan continues to operate for a short
while. Then, the projector goes into standby mode.
When cooling lamp
After cooling complete
A
B
During cooling, the POWER indicator flashes. In this state, the power
cannot be turned back on.
A
If you are in a hurry, there is no problem with unplugging the power cord
or turning off the power consunption in this state.
In standby mode.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
Adjusting the Projected Image
Adjusting the Projector Image Height
The projector is equipped with an elevator foot for adjust-
ing the image height.
To raise the image:
1. Press the foot adjuster button
.
2. Raise the image to the desired height angle , then re-
lease the button to lock the foot adjuster into position.
3. Use
to fine-tune the display angle.
To lower the image:
1. Press the foot adjuster button.
2. Lower the image, then release the button to lock the foot
adjuster into position.
3. Use
to fine-tune the display angle.
1
foot adjuster
button
3
2
Tilt Adjusting Wheel
foot adjuster
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out. To focus the im-
age, rotate the focus ring until the image is clear. The projector
will focus at distances from 5 to 40 feet (1.5 to 12.2 meters).
Zoom Lever
Focus Ring
Adjusting Projection Image Size
300"(762.5cm)
246.0"(625.0cm)
172.2"(437.5cm)
261.04"
(663.0cm)
123.0"(312.5cm)
213.97"
(543.5cm)
74.0"(187.5cm)
37.0" (93.8cm)
149.78"
(380.4cm)
106.98"
(271.7cm)
64.1"
(163.0cm)
32.1"
(64.1cm)
4.99'(1.5m)
9.84'(3.0m)
16.40'(5.0m)
22.97'(7.0m)
32.81'(10.0m)
40.03'(12.2m)
Max.
37.0"(93.8cm)
32.10"(81.5cm)
74.0"(187.5cm)
64.19"(163.0cm)
59.06" x 44.29"
123.0"(312.5cm)
172.2"(437.5cm)
246.0"(625.0cm)
300.0"(762.5cm)
Screen
(Diagonal)
Min.
106.98"(271.7cm) 149.78"(380.4cm) 213.97"(543.5cm) 261.04"(663.0cm)
98.43" x 73.82" 137.80" x 103.35" 196.85" x 147.64" 240.16" x 180.12"
29.50" x 25.60"
(75.0 x 62.5cm)
Max.(WxH)
(150.0 x 112.5cm) (250.0 x 187.5cm) (350.0 x 262.5cm) (500.0 x 375.0cm) (610.0 x 457.5cm)
Screen
Size
25.68" x 19.26"
(65.2 x 48.9cm)
51.35" x 38.51"
85.59" x 64.19"
119.82" x 89.87"
171.17" x 128.38" 208.83" x 156.62"
Min.(WxH)
(130.4 x 97.8cm) (217.4 x 163.0cm) (304.3 x 228.3cm) (434.8 x 326.1cm) (530.4 x 397.8cm)
Distance
4.99'(1.5m)
9.84'(3.0m)
16.40'(5.0m)
22.97'(7.0m)
32.81'(10.0m)
40.03'(12.2m)
This graph is for user’s reference only.
Notes
• No ceiling mount installation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Continued)
Adjusting the screen size and focus
Use the zooming lever to adjust the screen size.
Use the focusing lever to adjust the focus.
Notes
• Note that a lamp characteristics may rarely cause the
brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DMDTM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please
note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to XGA resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
• If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” will appear.
• If a signal not supported by the projector is input, the “Unsupport signal” will appear.
• If an unavailable operation button is pressed, the
icon will appear.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings
using the operation buttons on the control panel (main unit side) and remote control.
How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Display the Setting display menu.
1. Press the MENU button
2. Select a Category
Select a category by using
.
Displays the current
adjustments and settings of
selected category.
There are following five
categories:
Item shown with gray cannot
be adjusted with the current
input source.
Image adjustment menu
Display setting menu
Default setting menu
Set up menu
Status display menu
3. Adjustments & Settings
Press
to open the menu.
Item
Adjustment/Setting Value
5. End
Press the MENU
These marks signify
the items can be
adjusted/set by using
button
These marks signify that
there are options.
The menu disappears.
.
Press
to display a
list of options.
These marks signify the items can
be selected from the list by using�
.
After an item is selected, apply it by
pressing
.
The figure shows displays given for operation instructions purposes. As the display may
differ depending on the item, use the following pages as a reference.
4. Back
MENU button
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
The image adjustment menu
Use this menu to adjust image-related items.
Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”.
Item
Contrast
Description
BR
Adjust the image contrast.
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Lower
Brightness Adjust the brightness of the image.
Darker Brighter
Adjust the color of the image.
Lighter Deeper
Adjust the tint of the image color.
Reddish Greenish
Sharpness Adjust the sharpness of the image.
Softer Sharper
Set the function to reduce screen noise.
Higher
Yes
Yes
Yes
Yes
Yes
No
Color
Tint *1
No
No
Yes
Yes
No
Noise
reduction On (Enable)
No
Off (Disable)
Picture
mode
Yes
Press . Toggle the picture mode with
/
Bright/True color
R-level
G-level
B-level
Adjust red of the image color.
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Less red
More red
Adjust green of the image color.
Less green
More green
Adjust blue of the image color.
Less blue
Set the black level with
US: NTSC (US) mode
Japan: NTSC (JAPAN) mode
More blue
NTSC
/
button.
mode*1
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC]
and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is set to
US for other languages.)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
The display setting menu
Use this menu to set screen display-related items.
Item
Description
Screen size
(Full): Display with 1024 × 768 dot resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/PB/PR
)
Language
Select one of the languages below to use for displaying the menu and
messages
[
: Enter setting mode]
English/Français/Deutsch/Italiano/Español/Português/
/Svenska/Türkçe/Polski/
[
:Selection] [Apply:
]
/
/
/
Background
Icon
Display icons as function guides
On
Off
Off
Start-up
screen
Display start-up screen when power is turned on On
Note
• If “Thru” is selected for screen size, portions exceeding the native resolution (1024 ×
768 pixels) will not appear on the screen. Note that for RGB signals with clock frequency
140MHz or lower, all input pixel signals are sampled. However, if the clock speed is
higher than this, the RGB pixel signal is thinned before sampling.
• If you use the screen size setting function on commercial video software, broadcast or
cable-broadcasting programs to display images with the varying aspect ratio except for
the purpose of your private viewing and listening, it may infringe the copyright protected
by the copyright laws.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
The default setting menu
This menu shows placement status and other settings.
Item
Description
Projection
mode
Sets projection mode in accordance with Placement Style.
Standard : The factory default setting.
Rear-Desktop: When you select this function, the projector
reverses the image so you can project behind a translucent
screen.
No signal
power off
Set the timer to wait for the power to be turned off after signal input
stops.
Press . Switch with
and
Off (not turned off)//5 min./10 min./30 min./60 min.
Auto input
search
Set whether the input with signals is only selected or not.
On
Off
Lamp power [Note 1] Sets the lamp power.
Low
Standard
High
[Note 2]
Sets the cooling fan speed.
Standard
Reset all
Press
Resets all adjustments and settings to their factory settings.
Yes
No
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
Manual adjustments and settings
The menu items of the Set up menu vary depending on the input type, as shown in the
table below.
Use the
buttons to adjust the items in the table below, then press the
button when you are finished.
Description
BR
Auto. Keystone Automatically corrects the keystone
Yes
Yes
Yes
Yes
Yes
distortion. Press
Keystone
Correct the keystone (trapezoid) distortion of
the screen.
Yes
Screen shrinking
Screen shrinking
downward
upward
Auto
setting
Automatically adjusts items such as the
samplingphase depending on the type of
input signal.
Yes
No
No
Press the MENU button.
Phase
Adjust with
to eliminate flicker.
Yes
Yes
No
No
No
No
Frequency Adjust with
to eliminate periodic
patterns and flickering when many vertical
lines appear on the screen.
H-position Adjust the horizontal position of the image.
Yes
Yes
No
No
No
No
Move left
V-position Adjust the vertical position of the image.
Move down Move up
Move right
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menu (Continued)
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Input source name
RGB input mode [Note 1]
BR
Input
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
Mode name
H-resolution
V-resolution
H-frequency
V-frequency
Sync
Horizontal resolution (in dots)
Vertical resolution (in dots)
Horizontal sync frequency
Vertical sync frequency [Note 2]
Sync signal polarity [Note 3]
Y/PB/PR signal format
No
No
No
No
No
No
No
No
No
No
Signal format
Video mode
Lamp time
Yes
No
No
Color method of video signal
Time of lamp use [Note 4]
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Lamp reset count The count for lamp replacement
Total time
Version
The total time that this projector is used
Firmware version [Note 5]
Notes
1: The mode of supported RGB signals p.39 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a
counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a
store about getting a TLPLP8 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is referred to for
customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Trouble shooting
If you experience trouble with the projector, refer to the
following information. If the problem persists, please
contact your local reseller or service center.
Problem : No image appears on screen.
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Problem : Partial, scrolling or incorrectly displayed image.
Press “PJ Mode” on the Remote Control or press “AUTO SET” on
the Control Panel.
If you are using a PC:
For Windows 3.x:
1. In the Windows Program Manager, double click the “Windows
Setup” icon in the Main group.
2. Verify that your display resolution setting is less than or equal to
1280 x 1024.
For Windows 95, 98, 2000, XP:
1. From the “My Computer” icon, open the “Control Panel” folder,
and double click the “Display” icon.
2. Select the “Settings” tab
3. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will
also need to change the monitor display you are using. Refer
to the following steps.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
4. Verify the resolution setting is less than or equal to 1280 x 1024
resolution.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the computer.
2. Press the toggle output settings. example:[Fn]+[F4]
Compaq=>
Dell => [Fn]+[F8]
Gateway=>
IBM=>
[Fn]+[F4]
Hewlett
Packard
NEC=> [Fn]+[F3]
Toshiba =>
=>
[Fn]+[F4]
[Fn]+[F5]
[Fn]+[F4]
[Fn]+[F7]
Mac Apple:
System Preference-->Display-->Arrangement-->Mirror dis-
play
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
Problem : The screen of the Notebook or PowerBook com-
puter is not displaying a presentation.
If you are using a Notebook PC:
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s documentation for detailed
information.
Problem : Image is unstable or flickering
Use “Phase” to correct it. Refer to page 33.
Change the monitor color setting from your computer.
Problem : Image has vertical flickering bar
Use “Frequency” to make an adjustment. Refer to page 33.
Check and reconfigure the display mode of your graphic card to
make it compatible with the product.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
Problem : Image is out of focus
Adjusts the Focus Ring on the projector lens. Refer to page 27.
Make sure the projection screen is between the required distance 5
to 40 feet (1.5 to 12.2 meters) from the projector.
Problem : The image is stretched when displaying 16: 9
DVD.
The projector automatically detects 16:9 DVD and adjusts the aspect
ratio by digitizing to full screen with 4:3 default setting.
If the image is still stretched, you will also need to adjust the aspect
ratio by referring to the following:
Please select 4:3 aspect ratio type on your DVD player if you are
playing a 16:9 DVD.
If you can’t select 4:3 aspect ratio type on your DVD player, please
select 4:3 aspect ratio in the on screen menu.
Problem : Image is reversed.
Select “Default setting ” from the OSD and adjust the projection
direction. See page 32.
Problem : Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may make
a loud popping sound. If this happens, the projector will not turn on
until the lamp module has been replaced. To replace the lamp, follow
the procedures in the “Replacing the Lamp”. See page 38.
Problem: LED lighting message
Power LED
Green Orange
Message
Temp LED Lamp LED
Red
Standby State
(Input power cord)
Normal Mode
Cooling
Flashing
Error (Lamp failed)
Steady light =>
Error (Fan failed)
Flashing
No light =>
Error (Over Temp.)
Error
Flashing
Flashing
(Lamp cover failed)
Error
Flashing
(Color wheel failed)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
Replacing the lamp
The projector will detect the lamp life itself. It will show you a
warning message “The Lamp life is ending” When you see this
message, change the lamp.
Make sure the projector has been cooled down for at least
one hour before changing the lamp.
1
3
Warning: Lamp
compartment is hot!
Allow it to cool down
before changing lamp!
2
4
Lamp Replacing Procedure:
1. Switch off the power to the projector by pressing the Power
button twice.
2. Allow the projector to cool down at least 1 hour.
3. Disconnect the power cord.
Warning: To
reduce the risk of
4. Use a screwdriver to remove the screw from the cover.
personal injury, do not
drop the lamp module
or touch the lamp bulb.
The bulb may shatter
and cause injury if it is
dropped.
5. Push up and remove the cover.
6. Remove the 2 screws from the lamp module.
7. Pull out the lamp module.
To replace the lamp module, reverse the previous steps.
8. Reset the lamp timer.
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic mercury.
Be careful not to break used lamps, and dispose of them in accordance with local regulations.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
• It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]
reaches 2,000 hours, the icon
2,000 hours, they will appear when the power is on at the first time every 100 hours.) This
display disappears when you press button.
and a message will appear with a beep sound. (After
• Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,
the projector may fail to be powered on or the lamp may fail to come on.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
Computer Compatibility (Analog)
This project supports the following RGB signals. Note, however, that
depending on the computer model, the screen may show flicker or
streaking. Please adjust the projector if this happens.
(Press the SET UP button, and adjust automatically or manually.)
Refresh rate H-frequency
Clock
(MHz)
30
35
Resolution
Mode
[Hz]
70
[KHz]
31.5
640x350_70
640x350_85
640x400_85
VGA_60
VGA_72
VGA_75
640x350
640x400
85.08
85.08
59.94
72.8
75
37.86
37.86
31.46
37.86
37.5
35
25.17
31.5
31.5
36
32
35.5
36
40
50
49.5
56.25
65
640x480
720x400
VGA_85
85
70
43.26
31.5
720x400_70
720x400_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
85.03
56.25
60.3
72.18
75
37.92
35.15
37.87
48.07
46.87
53.67
48.36
56.47
60.02
68.67
63.98
79.97
63.85
67.5
800x600
85.06
60
XGA_70
XGA_75
XGA_85
70.06
75.02
84.99
60.02
75.02
70
75
1024x768
78.75
94.5
108
135
90.3
108
130
108
120
118
57.28
79.85
81
1280x1024_60
1280x1024_75
1152x864_70
1152x864_75
1152x864_85
1280x960_60
1280x960_75
SXGA +
1280x1024
1152x864
1280x960
75
84.99
60
77.09
60
75
75
Remark :
1400x1050
832x624
1024x768
1152x870
640x480
1024x768
1152x870
1280x960
60
74.55
75
75.06
60
75
63.98
49.725
60.24
68.68
31.35
60
MAC 16”
MAC 19”
MAC
MAC G4
i Mac DV
i Mac DV
i Mac DV
1.> “ ”compressed
*
computer image.
2.> The interlaced
analog signals are not
supported.
40
79
80.05
120
75
75
68.49
75
Note
Signals which resolution exceeds the native resolution (1024×768 pixels) will be compressed.
For this reason, some information will be lost, or image quality may be affected.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices (Continued)
Specifications
List of general specifications
Consumption Power
Weight
- 195W
- 1.0Kg
External Dimensions
Cabinet material
- 200 x 75.3 x 154.2 mm (WxHxD)
- AL & MG alloy + PC + ABS resin
Conditions for usage environment - Temp : 5 oC to 35 oC
Relative humidity : 30% to 70%
- 1 Chip DMD ™
Display pixels
Picture elements
Lens
- 786,432 pix els (1024H x 768V)
- Zoom lens F= 2.7-2.88 f = 28.43 -
32.73 mm
Lamp
- High - pressure mercury lamp
- 31.7- 300 inches
Projection screen size
Projection distance
- 1.5m – 12.2m
Connection terminal
B
R
Computer Input (VGA)
- Mini D sub 15 pin RGB/Y/P / P
(Dual use)
Video Input (x 1)
S Video Input (Standard x 1)
USB Port
- RCA Pin Jack
- Mini DIN 4 pin
- For mouse remote control
Notes
• This model complies with the above specification
• Designs and specification are subject to change without notice.
• This model may not be compatible with features and/or specifications that maybe added in
the future.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
About Lamp
About Lamp
The product’s light source is a mercury lamp that lights at increased
internal pressure. Be sure to fully understand the following character-
istics of the lamp and handle it with extreme care.
• The lamp may burst with a loud noise due to impact or deteriora-
tion, or fail to light at the expiration of its life.
• How long it takes before the lamp bursts or the life expires may
vary greatly by lamp.
Some may burst shortly after first use.
• Burst is likely to happen if the lamp is used after the replacement
period has elapsed.
• When the lamp bursts, the broken pieces of glass may get inside
the product or be released outside from the openings for ventilation.
• When the lamp bursts, a slight amount of mercury gas enclosed in
the lamp along with glass dust may be released from the openings
for ventilation.
Immediately replace the lamp when a sign ap-
pears on the screen.
• When the replacement time approaches, a message will appear on
the screen.
• The risk of burst will increase if the lamp is continuously used with-
out being replaced.
• Frequently check the used hours and prepare spares when the
replacement time approaches.
When the lamp is broken
• If glass components, including a lamp and a lens, should break,
handle the broken pieces with care to avoid injury and contact your
dealer for repair service.
• In the event of lamp burst, unplug the product from the wall outlet,
leave and completely ventilate the room. Then, thoroughly clean
the area around the projector and discardany edible items placed in
that area.
• When the lamp bursts, consult a doctor if glass dust or mercury gas
gets into your eyes or you breathe it.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
About Lamp
Lamp replacement
A lamp is consumable supplies. If used for extended periods, images
will appear dark, and the lamp could burn out. This is characteristic of a
lamp, and is not malfunction. (The lifetime of the lamp depends on condi-
tion of use.) If this happens, replace it with a new one.
CAUTION
If you have been using the projector, the lamp will be very hot, and may
cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to
broken pieces and contact your dealer for repair service.
Lens cleaning
• Clean the lens with a commercially available
blower and/or lens cleaner.
• The lens is easily scratched, so do not rub it
with hard objects, or strike it.
Main unit cleaning
• Clean the main unit after unplugging the
power cord.
• Wipe dirt off the main unit gently with a soft
cloth.
• Do not wipe the main unit with a damp cloth.
Doing so may allow water to get inside, result-
ing in an electric shock or failure.
• Do not use benzene, thinner and the like as
they may deform or discolor the unit or dam-
age the paint surface.
• When using a chemically treated cloth, follow
the precautions included with the cloth.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
|