Toshiba Projector TDP MT400 User Manual

English
OWNER’S MANUAL  
DLP™ PROJECTOR  
TDP-MT400  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Before Using  
SAFETY PRECAUTIONS  
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended  
to alert the user to the presence of uninsulated "dangerous voltage" within the product's  
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to  
persons.  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
RESPONSIBLE PARTY: Toshiba America Consumer Products LLC  
82 Totowa Road, Wayne, New Jersey, 07470  
The exclamation point within an equilateral triangle is intended to alert the user to the  
presence of important operating and maintenance (servicing) instructions in the  
literature accompanying the appliance.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES  
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.  
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.  
Phone: (973)628-8000  
WARNING:  
USA only  
Changes or modifications made to this equipment, not expressly approved by  
Toshiba, or parties authorized by Toshiba, could void the user’s authority to  
operate the equipment.  
WARNING: Handling the cord on this product or cords associated with accessories sold with  
this product, will expose you to lead, a chemical known to the State of California  
USA only  
to cause birth defects or other reproductive harm. Wash hands after handling.  
Notice:  
CANADA only  
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil  
numérique de la classe B est conforme à la norme NMB-003 du Canada.  
WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to  
environmental considerations. For disposal or recycling information, please  
contact your local authorities or the Electronic Industries Alliance:www.eiae.org.  
USA only  
USA only  
MODEL NAME: TDP-MT400  
TRADE NAME: DLP™ PROJECTOR  
Tested To Comply  
MODEL NAME:TDP-MT400  
With FCC Standards  
FOR HOME OR OFFICE USE  
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can  
be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
IMPORTANT SAFETY INSTRUCTIONS  
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND  
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE  
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE  
5. Heat  
8. Power-Cord Protection  
The product should be situated  
Power-supply cords should be  
routed so that they are not likely to  
be walked on or pinched by items  
placed upon or against them,  
paying particular attention to cords  
at plugs, convenience receptacles,  
and the point where they exit from  
the product.  
away from heat sources such as  
radiators, heat registers, stoves, or  
other products (including  
REFERENCE.  
This unit is fully transistorized and does not contain any parts that can be repaired by the  
user.  
amplifiers) that produce heat.  
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO  
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL ONLY.  
1. Read Owner's Manual  
3. Source of Light  
After unpacking this product, read  
the owner's manual carefully, and  
follow all the operating and other  
instructions.  
Do not look into the lens while the  
lamp is on. The strong light from  
the lamp may cause damage to  
your eyes or sight.  
6. Water and Moisture  
Do not use this product near water.  
- for example, near a bath tub,  
wash bowl, kitchen sink, or laundry  
tub; in a wet basement; or near a  
swimming pool and the like.  
9. Overloading  
Do not overload wall outlets; to  
reduce the risk of electric shock,  
do not use the polarized plug with  
an extension cord , receptacle, or  
other outlet unless the blades can  
be inserted completely with three-  
wire grounding type to prevent  
blade exposure. As this can result  
in a risk of fire or electric shock.  
2. Power Sources  
4. Ventilation  
This product should be operated  
only from the type of power source  
which does not exceed the voltage  
range specified on the  
rating label and the power cord.  
If you are not sure of the type of  
power supply to your home,  
consult your product dealer or  
local power company.  
Openings in the cabinet are  
7. Cleaning  
provided for ventilation and to  
ensure reliable operation of the  
product and to protect it from  
overheating, and these openings  
must not be blocked or covered.  
The openings should never be  
blocked by placing the product on  
a bed, sofa, rug or other similar  
surface. This product should not  
be placed in a built-in installation  
such as a bookcase or rack unless  
proper ventilation is provided.  
Unplug this product from the wall  
outlet before cleaning. Do not use  
liquid cleaners or aerosol cleaners.  
Use a soft cloth for cleaning.  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
IMPORTANT SAFETY INSTRUCTIONS (Continued)  
e) If the product has been dropped or  
damaged in any way (If the cabinet  
should break, please handle with  
care to avoid injury) .  
f) When the product exhibits a  
distinct change in performance -  
this indicates a need for service.  
10. Lightning storms  
12. Do not place the product  
vertically  
15. Accessories  
For added protection for this  
product during storm, or when it is  
left unattended and unused for  
long periods of time, unplug it from  
the wall outlet. This will prevent  
damage to the product due to  
lightning and power-line surges.  
However, while it is thundering or  
lightning, do not touch the  
apparatus and any connected  
cable and/or equipment.  
This will prevent you from  
receiving the electric shock by an  
electric surge.  
Do not place this product on an  
unstable cart, stand, tripod,  
bracket, or table. The product may  
fall, causing serious injury to a  
child or adult, and serious damage  
to the product. A product and cart  
combination should be moved with  
care. Quick stops, excessive  
force, and uneven surfaces may  
cause the product and cart  
combination to overturn.  
Do not use the product in the  
upright position to project the  
pictures at the ceiling, or any other  
vertical positions. It may fall down  
and dangerous.  
17. If glass components,  
including lens and lamp,  
should break, contact your  
dealer for repair service.  
This product incorporates glass  
components, including a lens and  
a lamp. If such parts should  
break, please handle with care to  
avoid injury and contact your  
dealer for repair service. The  
broken pieces of glass may cause  
to injury. In the unlikely event of  
the lamp rupturing, thoroughly  
clean the area around the  
13. Stack Inhibited  
Do not stack other equipment on  
this product or do not place this  
product on the other equipment.  
Top and bottom plates of this  
product develops heat and may  
give some undesirable damage to  
other unit.  
S3125A  
16. Damage Requiring Service  
Unplug this product from the wall  
outlet and refer servicing to  
qualified service personnel under  
the following conditions:  
11. Object and Liquid Entry  
projector and discard any edible  
items placed in that area.  
Never push objects of any kind  
into this product through openings  
as they may touch dangerous  
voltage points or short-out parts  
that could result in a fire or electric  
shock. Never spill liquid of any  
kind on the product.  
a) When the power-supply cord or  
plug is damaged.  
b) If liquid has been spilled, or  
objects have fallen into the  
product.  
c) If the product has been exposed to  
rain or water.  
18. Servicing  
Do not attempt to service this  
product yourself as opening or  
removing covers may expose you  
to dangerous voltage or other  
hazards. Refer all servicing to  
qualified service personnel.  
14. Attachments  
d) If the product does not operate  
normally by following the operating  
instructions. Adjust only those  
controls that are covered by the  
operating instructions as an  
improper adjustment of other  
controls may result in damage and  
will often require extensive work by  
a qualified technician to restore  
the product to its normal  
Do not use attachments not  
recommended by the product  
manufacturer as they may cause  
hazards.  
operation.  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
IMPORTANT SAFETY INSTRUCTIONS (Continued)  
POWER SUPPLY CORD SELECTION  
If your line voltage is 220 to 240V, use one of the following types of cable.  
19. Replacement Parts  
22. Do not use the product in  
a closed installation state.  
When replacement parts are  
required, be sure the service  
technician has used replacement  
parts specified by the  
manufacturer or have the same  
characteristics as the original part.  
Unauthorized substitutions may  
result in fire, electric shock, or  
other hazards.  
Plug  
Plug  
Do not place the product in a box  
or in any other closed installation  
state. Otherwise it may overheat.  
This could result in a risk of fire.  
configuration Plug type  
Line voltage  
220 – 240V  
configuration Plug type  
Line voltage  
200 – 240V  
Australian  
240V  
10A  
EURO  
UK  
Switzerland 200 – 240V  
240V  
6A  
23. Do not look into the laser  
light source of the remote  
control or direct the laser  
pointer toward a person or  
a mirror.  
220 – 240V  
(Replacement of the lamp only  
should be made by users.)  
Use a 5A fuse which is approved by ASTA  
or BSI to BSI362.  
Always replace the fuse cover after  
changing the fuse.  
North American 200 – 240V  
240V  
15A  
20. Safety Check  
The laser beam may cause  
damage to the eyes or sight.  
Upon completion of any service or  
repairs to this product, ask the  
service technician to perform  
safety checks to determine that  
the product is in proper operating  
condition.  
IMPORTANT PRECAUTIONS  
Save Original Packing Materials  
The original shipping carton and packing materials will come in handy if you ever have to  
ship your projector. For maximum protection, repack the set as it was originally packed at  
the factory.  
Moisture Condensation  
Never operate this unit immediately after moving it from a cold location to a warm location.  
When the unit is exposed to such a change in temperature, moisture may condense on  
the lens and the crucial internal parts. To prevent the unit from possible damage, do not  
use the unit for at least 2 hours when there is an extreme or sudden change in tempera-  
21. Do not leave thermal-paper  
documents or easily  
deformed items on top of  
the unit or near the air  
exhaust for long periods of  
time.  
ture  
.
Place and Manner of Installation  
Do not place in hot locations, such as near heating equipment. Doing so could cause  
malfunction, and shorten the life of the projector.  
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,  
shortening their lives, and darkening the screen.  
• Do not use the product vertically in any upright position or slantwise in an angle of 20  
degrees or more.  
Using this instrument near a TV or radio may cause interference to the images or audio  
sound. If this happens, move it away from the TV or radio.  
The heat from the unit could erase  
the information on the thermal  
paper, or cause deformation or  
warping.  
Moving the projector from a low-temperature room to a high-temperature room may  
cause condensation on the lens or internal parts in the instrument. If you continue to use  
it in that situation, the malfunction may result. Ensure to wait until the condensation  
naturally disappears.  
In a high altitude location where air is thin, cooling efficiency is reduced so use the  
p.31  
projector with [Fan mode] set to [High].  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
IMPORTANT PRECAUTIONS (Continued)  
Avoid Volatile Liquid  
OTHER CAUTIONS AND INFORMATIONS (Continued)  
Trademarks  
VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of  
International Business Machines Corporation.  
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or  
plastic products touching the unit for a long time. They will leave marks on the finish.  
If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.  
Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas  
Instruments.  
Macintosh is a registered trademark of Apple Computer, Inc.  
Windows is a registered trademark of Microsoft Corporation in the U.S. and other  
countries.  
Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems  
Incorporated.  
EXEMPTION CLAUSES  
Toshiba Corporation bears no responsibility in the case of damages arising from natural  
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts  
by third parties, other accidents, or use under abnormal conditions including erroneous or  
improper operation and other problems.  
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work  
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the  
inability to use this unit.  
Notational Conventions Used in This Manual  
References to pages with related information are annotated as follows.  
p.36  
For example, if making a reference to page 36:  
The illustrations in this document are for reference purposes only and may not reflect  
your package exactly.  
Toshiba Corporation accepts no liability whatsoever for any damages arising from not  
having followed the descriptions in this Instruction Manual.  
Toshiba Corporation accepts no liability whatsoever for any damages arising from  
malfunctions arising from combination with equipment or software that is not related to  
Toshiba Corporation.  
REMOTE CONTROL BATTERIES  
Caution  
• Never throw batteries into a fire.  
Using the batteries improperly may cause them to explode or leak and lead to burn or injury.  
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and  
consult a doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue  
paper. (Dispose of the used tissue paper as flammable garbage after moistening with water.)  
OTHER CAUTIONS AND INFORMATIONS  
Copyrights  
Notes  
Showing or transmitting commercial imaging software or broadcast or cable-broad  
casting programs with the purpose of other than the personal and private viewing,  
including modifying images using the freeze or resize functions, or displaying with the  
varying aspect ratio of the images, could violate the direct or indirect copyrights of the  
imaging software or broadcast program, etc., if done without first consulting with the  
copyright holder. For this reason, please take appropriate measures before performing  
one of the actions listed above, including obtaining a license from the copyright holder.  
• Be sure to use R6(size AA) size batteries.  
• Dispose of batteries in a designated disposal area.  
• Attention should be drawn to the environmental aspects of battery disposal.  
• Do not mix different battery types or combine used batteries with new ones.  
• If the remote control does not operate correctly, or if the operating range becomes  
reduced, replace both batteries with new ones.  
• If the batteries are dead or if you will not be using the remote control for a long time,  
remove the batteries to prevent battery acid from leaking into the battery compartment.  
Disposal  
This product contains substances which are harmful to humans and the environment.  
The lamp contains mercury.  
Please dispose of this product or used lamps in accordance with local regulations.  
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as  
household waste. By ensuring this product is disposed of correctly, you will  
help prevent potential negative consequences for the environment and  
human health, which could otherwise be caused by inappropriate waste  
handling of this product. For more detailed information about recycling of this  
product, please contact your local city office, your household waste disposal  
service or the shop where you purchased the product.  
In the spaces provided below, record the Model and Serial No. located at the bottom of your  
projector.  
Model No.  
Serial No.  
Retain this information for future reference.  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
CONTENTS  
Before Using  
Others  
SAFETY PRECAUTIONS ..................................................................................  
IMPORTANT SAFETY INSTRUCTIONS ...........................................................  
POWER SUPPLY CORD SELECTION..............................................................  
IMPORTANT PRECAUTIONS ...........................................................................  
2
4
9
9
Trouble indications ............................................................................................. 36  
Before calling service personnel ........................................................................ 37  
Specifications..................................................................................................... 38  
List of general specifications .......................................................................... 38  
Separately sold product.................................................................................. 38  
List of supported signals (RGB signals) ......................................................... 39  
List of supported signals (DVI signals) ........................................................... 40  
List of supported signals (Y/PB/PR signals) .................................................... 41  
List of supported signals (Video, S-Video signals) ......................................... 41  
Pin assignment of COMPUTER terminal ....................................................... 41  
Pin arrangement for the DVI-D terminal ......................................................... 42  
CONTROL terminal ........................................................................................ 43  
EXEMPTION CLAUSES .................................................................................... 10  
OTHER CAUTIONS AND INFORMATIONS ...................................................... 10  
REMOTE CONTROL BATTERIES .................................................................... 11  
CONTENTS ....................................................................................................... 12  
Preparations  
Checking the package contents ......................................................................... 14  
Names of each part on the main unit................................................................. 15  
Names of each part on the control panel and remote control............................ 16  
Parts on the rear panel ...................................................................................... 17  
Preparing and using the remote control............................................................. 18  
Placement .......................................................................................................... 19  
Connection......................................................................................................... 20  
Operations  
Turning the power on and off ............................................................................. 21  
Basic operations ................................................................................................ 23  
Using handy features ......................................................................................... 25  
Using auto setting........................................................................................... 25  
Cutting off the picture temporarily (Mute) ....................................................... 27  
Freezing the image (Freeze) .......................................................................... 27  
Using the menus ................................................................................................ 28  
How to use the menus .................................................................................... 28  
The image adjustment menu .......................................................................... 29  
The display setting menu................................................................................ 30  
The default setting menu ................................................................................ 31  
Displaying Information (Status display) .......................................................... 32  
Maintenance  
About lamp......................................................................................................... 33  
Lamp replacement ............................................................................................. 33  
Lens and main unit cleaning .............................................................................. 35  
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Preparations  
Names of each part on the main unit  
Checking the package contents  
Please make sure that the following items are included in the box, along with the main unit. If  
any item is missing, please contact the store immediately where you purchased the product.  
(6)  
(5)  
(4)  
(3)  
(1)  
(2)  
(1)  
(4)  
(5)  
(6)  
(2)  
(3)  
(7)  
(11) (12)  
(8)  
Back  
(9)  
(10)(8)  
Front  
(1) Remote control  
(2) R6 (SIZE AA) batteries for remote control (2)  
(3) Owner’s Manual  
(4) Video cable  
Name  
: Function  
(5) S-Video cable  
(6) Power cord (See note)  
p.24  
(1) Foot adjuster release button : Press to stow the foot adjuster.  
p.18  
(2) Infrared remote sensor  
(3) Lens  
(4) Air intake  
: Senses commands from the remote control.  
: Projects expanded image.  
: Draws in air from outside the projector.  
Note  
The shape and number of supplied power cords vary depending on the product destination.  
p.16  
(5) Control panel  
(6) Zooming lever  
(7) Air exhaust  
(8) Tilt adjuster  
(9) Rear panel  
: Operates the projector.  
: Adjusts screen size.  
p.24  
: Expels air that has grown hot inside the projector.  
: Adjusts the projector’s horizontal tilt.  
: Connects external devices.  
p.24  
p.17  
p.24  
(
(
(
10) Focusing lever  
11) Foot adjuster  
12) Lamp cover  
: Adjusts screen focus.  
p.24  
: Adjusts the vertical projection angle.  
p.34  
: Remove to replace lamp.  
14  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Names of each part on the control panel and remote control  
Parts on the rear panel  
Control panel  
Remote Control  
(7)  
(2)  
(3) (4)  
(5)  
(6)  
(1)  
Remote control  
transmitter  
(9) (10) (11)  
(4)  
(2)  
(12)  
(3)  
(6)  
(1)  
(2)  
(8)  
(13)  
(1)  
(8)  
(7)  
(6)  
(10)  
(9) (8)  
(3)  
(4)  
Name  
: Main Function  
: Senses commands from the remote control.  
: When operating the projector via a computer, connect  
(7)  
(5)  
p.18  
(1) Infrared remote sensor  
(2) CONTROL terminal  
p.43  
this to the controlling computer’s RS-232C port.  
(3) S-VIDEO terminal  
(4) VIDEO terminal  
(5) Component video terminal  
: Input S video signals from video equipment.  
: Input video signals from video equipment.  
: Input component video signal (Y/PB/PR) from a video  
equipment or other source.  
(6) COMPUTER terminal  
(7) DVI-D terminal  
: Input RGB signal from a computer or other source.  
: Input digital RGB signal from a computer or other  
source.  
: AC power line ON (standby)/OFF.  
: Connect the supplied power cord here.  
: Attach a safety cable or any other antitheft device.  
Name  
: Main Function  
(1) ENTER button  
(2) MENU button  
(3) SET UP button  
(4) ON/STANDBY button  
(5) ON indicator  
: Accepts the selected mode.  
: Displays menus.  
: Sets up image and mode.  
: Turns the power on/off (standby).  
: Displays whether power is on or off.  
p.28  
(8) Main power switch  
(9) AC IN socket  
p.25  
p.21  
(
10) Antitheft lock hole  
p.21  
p.23  
(6) INPUT button  
(7) RETURN button  
(8) Selection button  
(9) LAMP indicator  
: Selects input.  
Notes  
: Goes back one screen.  
: Menu selections and adjustments,etc.  
: Displays lamp mode.  
• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the  
product also supports signals from video equipment marked “Y/CB/CR.”  
• Input signal specifications for the DVI terminal complies with the DVI 1.0 Specifications.  
• Please note that the operations for the functions not covered in these specifications are  
not guaranteed. Because this is an evolving technology, it is possible that some devices  
may not operate properly with the projector.  
p.29  
p.22  
p.36  
(
(
(
(
10) TEMP indicator  
11) FAN indicator  
12) FREEZE button  
13) MUTE button  
: Lights when internal temperature is too high.  
p.36  
: Displays cooling fan mode.  
p.27  
: Pauses image.  
p.27  
: Cuts off the picture temporarily.  
• This supports HDCP (High-bandwidth Digital Content Protection).  
Note  
• For the remainder of this manual, buttons are referred to as follows:  
Selection buttons  
; ENTER button ⇒  
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Placement  
Preparing and using the remote control  
Loading dry-cell batteries  
into the remote control  
q Remove the battery cover.  
Operating the remote  
Placement Styles  
As shown in the figures below, this device can be placed in 4 different styles.  
control  
The factory setting is “floor-mounted front projection.Set the Projection mode in the  
Point the remote control toward the  
projector’s infrared remote sensor,  
and press a button on the remote  
control.  
p.31  
default setting menu  
, in accordance with your needs.  
Floor-mounted front projection  
Floor-mounted rear projection  
• Operating the projector from the front  
w Insert the dry-cell batteries.  
Ceiling-mounted front projection  
Ceiling-mounted rear projection  
Be sure to align the plus and minus  
ends of the batteries properly.  
Approx. 15°  
Approx. 5m  
• Operating the projector from the rear  
WARNING  
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.  
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus  
resulting in injury.  
Two batteries (R6, SIZE AA) are used.  
e Replace the battery cover.  
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the  
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.  
Improper mounting could cause the projector to fall, resulting in an accident.  
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let  
everyone involved with the use of the projector know that fact.  
Approx. 15°  
Approx. 5m  
Projection Distance and Size  
Use the figures, tables, and formulas below to determine the projection size and projection distance.  
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)  
Dry-cell batteries  
• Before using the batteries, be sure to observe the Safety Precautions described in  
Screen  
As seen from above  
previous pages.  
a (min length) = projection size (inches) × 0.0350  
• Remove batteries from remote control when not using for extended periods.  
• If the remote control stops working, or if its range decreases, replace all the batteries with  
new ones.  
°
90  
a (max length) = projection size (inches) × 0.0421  
The remote control  
• The remote control may fail to operate if the infrared remote sensor is exposed to bright  
sunlight or fluorescent lighting.  
• Do not drop or bang.  
• Do not leave in hot or humid locations.  
• Do not get wet or place on top of wet objects.  
• Do not take apart.  
• In rare cases, ambient conditions could impede the operation of the remote control. If this  
happens, point the remote control at the main unit again, and repeat the operation.  
projection distance a (m)  
projection  
size  
height (H)  
(cm)  
min length  
max length  
As seen from the side  
(zooming max) (zooming min)  
Lens center  
35.66  
40  
60  
1.50  
1.68  
2.52  
3.37  
4.21  
6.31  
8.41  
16.43  
18.43  
27.64  
36.86  
46.07  
69.11  
92.15  
131.72  
1.40  
2.10  
2.80  
3.50  
5.25  
7.00  
10.00  
H
80  
°
90  
100  
150  
200  
285.89  
a
a is the distance (m) between the lens and the  
screen, and corresponds to a range of 1.50 m to  
10.00 m. H is the height from the image bottom to  
the center of the lens.  
18  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Connection  
Turning the power on and off  
Before connection  
Connecting the power cord  
• Read the owner’s manual of the device you are connecting to the projector.  
• Some types of computer cannot be used or connected to this projector.  
Insert the power cord connector into the  
AC IN socket of the projector.  
1
p.39  
Check for an RGB output terminal, supported signal  
Turn off the power of both devices before connecting.  
, etc.  
Insert the power cord plug into a wall or  
other power outlet.  
2
• The figure below is a sample connection. This does not mean that all of these devices  
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)  
Power cord connector  
(Supplied)  
Removing the lens cover  
Be sure to remove the lens cover when the power is  
turned on. If it is left on, it could become deformed due  
to heat.  
Computer (for control)  
Video recorder,  
DVD player, etc.  
VCR, etc  
To S-Video  
output  
To video  
output  
To RS-232C  
terminal  
p.43  
S-Video cable  
(supplied)  
Control cable  
Video cable (supplied)  
Turning the power on  
1
Turn on the main power switch  
The ON indicator will change to  
orange, indicating standby mode.  
• After the main power switch is turned  
on, the inner cooling fan starts  
cooling.  
(Orange)  
Remote  
Control  
2
Press the ON/STANDBY  
button.  
The power turns on, and the following  
3 green indicators light: ON, LAMP,  
and FAN. After a moment, the start-up  
screen appears.  
Start-up screen  
Control panel  
DVI cable  
(not supplied)  
RGB component video cable  
(not supplied)  
To Y/CB/CR output  
RGB cable  
(not supplied)  
Green (Y)/Blue (CB)/Red (CR  
)
To DVI output  
DVD video recorder, etc.  
To RGB output  
CAUTION  
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause  
damage to your eyes or sight.  
Computer  
Computer  
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.  
• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause  
burns, deform/break the object.  
Notes  
• If you want to feed the digital RGB signal, separately available DVI cable is needed.  
• If you are using the digital RGB signal for input to this unit, some computer models or a  
certain type of DVI cable may cause on rare occasions noise on the screen. If such is a  
case, decrease your computer’s refresh rate or the resolution. It is also recommended to  
use a DVI cable in 2 m or less in length.  
20  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Turning the power on and off (Continued)  
Basic operations  
Notes  
Turn on the power.  
Turn on the power by following the instructions in “Turning the power on”  
1
p.21  
.
• The start-up screen will disappear after a moment.You can dismiss the start-up screen  
before this by performing any operation.You can also configure the start-up screen not to  
p.30  
appear via the Display setting menu  
.
2
Select the language and the lamp power (When using the  
first time).  
When the projector is used for the first time after purchase, menu for language and  
lamp power selection and configuration is displayed in English. (If the screen is out of  
• The first time you use the projector after purchase, after the start-up screen disappears,  
p.23  
the Language menu is displayed  
.
Turning the power off  
focus, adjust it according to the step .)  
6
English  
French  
German  
Italian  
Spanish  
Portuguese  
Russian  
Swedish  
Turkish  
Japanese  
Chinese (simplified)  
Chinese (traditional)  
Korean  
1
Press the ON/STANDBY button.  
q Use the  
or  
button to select the  
button.  
desired language and press the  
Message for setup confirmation is displayed in a  
selected language.  
Then, the menu for lamp power selection and  
configuration is displayed. It is automatically set as  
Standard.To change the setting, follow the step w.  
A message appears on the screen, confirming that you wish to shut off the power. This  
message will disappear after a moment. (This operation is no longer valid after the  
message disappears.)  
Press the ON/STANDBY button again.  
2
The screen turns off, but the internal cooling fan continues to operate for a short while.  
Then, the projector goes into standby mode.  
w Using the  
power and press the  
The lamp power, if selected, will be toggled without  
pressing the button. The display automatically  
or  
button, select the lamp  
When cooling lamp  
During internal cooling  
After cooling complete  
button.  
(Green)  
Flashing  
(Green)  
(Off)  
(Green)  
(Off)  
(Off)  
disappears in a few seconds.  
(Orange)  
(Orange)  
(Orange)  
A
B
C
Notes  
During cooling, the LAMP indicator flashes. In this state, the power cannot be  
turned back on.  
A
B
• When the projector is turned on the next time, the Language and Lamp power  
menus do not appear upon startup. However, if “Reset all” is executed from the  
After the LAMP indicator goes off, the cooling fan continues to operate for a  
short while, in order to expel excess internal heat. If you are in a hurry, there is  
no problem with unplugging the power cord or turning off the main power switch  
in this state.  
p.31  
Default setting menu  
, the Language and Lamp power menus will be  
displayed the next time when the power is turned on.  
• The language can also be set via the Display setting menu  
via the Default setting menu  
p.30  
and Lamp power  
p.31  
.
• This owner’s manual assumes that English has been selected.  
In standby mode  
C
Activate the connected device.  
Turn on and start the connected device such as a computer.  
3
4
Note  
• The projector consumes about 12W of power in standby. We recommend that you unplug  
the power cord or turn off the main power switch if you will not be using the projector for  
an extended period.  
Press the INPUT button.  
An image of the connected equipment is projected.  
PRECAUTION  
Each time you press the INPUT button, it switches to the input of the connected  
equipment.  
• If the power cord is unplugged before cooling is complete, give the lamp time (about 5  
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.  
Notes  
p.31  
• When [Auto input search] is set to [On] in the default setting menu  
, the image of  
the equipment which is connected and turned on is projected.  
• Moving pictures generated with the DVD software for computers may appear unnatural if  
it is projected with this projector, but it is not a malfunction.  
22  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Using handy features  
Using auto setting  
Basic operations (Continued)  
5
Projector placement angle adjustments  
The placement angle and the height of the projected image can be adjusted by the foot  
adjuster.  
Remote  
This function sets up the projector to the optimum state for  
each type of the input signal by using simple operations.  
Control panel  
Control  
1
Press the SET UP button.  
q Lift up the front of the projector to  
1
the desired angle, then press the  
The Set up menu appears.  
foot adjuster release button.  
The foot adjuster extends. Release the  
button to lock the position.  
2
Press the SET UP button again.  
The displayed menu item is automatically adjusted/set.  
For computer input, the  
processing.  
icon will appear during  
w To adjust the horizontal angle, use  
the tilt adjuster.  
p.26  
For manual adjustment and setting, see the following table  
.
To stow the foot adjuster, hold up the projector  
while pressing the foot adjuster release button,  
then slowly lower the projector.  
Notes  
2
• The image may not be projected or auto adjustment/setting may not be performed  
correctly for input signals other than those supported by the projector  
p.39 p.40  
,
,
p.41  
.
6
Adjusting the screen size and focus  
• Keystone adjustment cannot be corrected automatically.  
q
Use the zooming lever to adjust the screen size.  
1
2
w Use the focusing lever to adjust the focus.  
Correcting the keystone distortion  
Readjusting the projection size with the  
zooming lever after focusing will cause the  
projected image to be out of focus. In that case,  
perform focusing again.  
p.24  
When the foot adjuster  
is used to change the projector placement angle while  
projecting the image, the picture will undergo keystone (trapezoidal) distortion.  
This projector is capable of correcting this keystone distortion  
.
Before correction After correction  
Notes  
• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.  
• A lamp is consumable item. If used for extended periods, images will appear dark, and  
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The  
lifetime of the lamp depends on conditions of use.)  
• The DMDTM is made using extremely advanced technology, but there may be black spots  
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please  
note that these are not malfunctions.  
Manual adjustment  
Press the SET UP button to display the Set up menu and select [Keystone]. Use  
the buttons for keystone adjustment. When the adjustment is finished, press  
p.39  
• Although this projector supports a wide range of RGB signals  
be expanded or shrunk, which will affect image quality slightly.  
, any resolutions will  
the RETURN button. The menu disappears.  
• With some models of computer having LCD displays or the like, displaying images  
simultaneously on the projector and the monitor’s display may prevent the images from  
displaying properly. If this happens, turn off the computer’s LCD display. For information  
on how to turn off the LCD display, see the owner’s manual of your computer.  
• If a signal not supported by the projector is input, the “Unsupported signal” will appear.  
• If no signal is being input from the connected device, the “No signal” will appear.  
Notes  
• Depending on the amount of keystone adjustment and the content of images, some  
information may be lost, or the picture quality may suffer.  
• Keystone adjustment is available for the keystone distortion in a slant angle of ±15  
degrees.  
• Keystone adjustment will not change the shape of the menus, the start-up screen,  
and the background (with no signal input).  
• If an unavailable operation button is pressed, the  
icon will appear.  
24  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Using handy features (Continued)  
Manual adjustments and settings  
Cutting off the picture temporarily (Mute)  
The menu items of the Set up menu vary depending on the input type, as shown in  
the table below.  
Remote  
Control  
When you want to project the images of another projector, overhead  
projector, etc. temporarily, this projector’s images can be turned off.  
Use the  
buttons to adjust the items in the table below, then press  
Press the remote control’s MUTE button.  
The picture is cut off. (The Mute function is released when pressing  
the MUTE button again.)  
the RETURN button when you are finished.  
Video  
S-video  
Select Item  
Keystone  
Description  
Computer Y/PB/PR  
DVI  
Yes  
Notes  
Correct the keystone (trapezoid) distortion of the  
screen.  
Yes  
Yes  
Yes  
No  
Yes  
• The  
icon will appear while mute is in effect.  
Screen shrinking  
downward  
Screen shrinking  
upward  
• Operating any other functions will also cancel the muting.  
Freezing the image (Freeze)  
Auto setting Automatically adjusts items such as the sampling  
phase depending on the type of input signal.  
Press the SET UP button.  
No  
No  
Remote  
Control  
The image being projected can be frozen. This function is to be used to  
pause a video during a presentation, etc.  
Phase  
Adjust with  
to eliminate flicker.  
Yes  
Yes  
No  
No  
No  
No  
No  
No  
Press the remote control’s FREEZE button.  
The picture pauses. (The Freeze function is released when pressing  
the FREEZE button again.)  
Frequency Adjust with  
to eliminate periodic patterns  
and flickering when many vertical lines appear  
on the screen.  
Image’s  
Adjust the horizontal position of the image.  
Yes  
No  
No  
No  
Notes  
H-position Move left  
Image’s Adjust the vertical position of the image.  
V-position Move down Move up  
Adjusts the clamp pulse position.  
Lower Higher  
Adjusts the clamp pulse width.  
Narrower Wider  
Move right  
• The  
icon will appear while freeze is in effect.  
Yes  
Yes  
No  
No  
No  
No  
No  
No  
• Other operation will also release the freeze.  
• Even if an image is frozen on the projector, the pictures are running on the video or  
other equipment.  
• If you use this function on video software sold on the market, broadcast or  
broadcast on cable except for the purpose of your private viewing and listening, it  
may infringe the copyright protected by the copyright laws.  
Clamp 1  
Clamp 2  
Yes  
No  
No  
No  
26  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Using the menus  
You can call up on-screen menus, and conduct a number of adjustments and settings using  
The image adjustment menu  
Use this menu to adjust image-related items.  
p.16  
the operation buttons  
on the control panel (main unit side) and remote control.  
Items that can be adjusted are marked with Yes”, and those that cannot are marked with “No”.  
How to use the menus  
Video  
S-video  
The menu shown below is for operation instructions purposes and might differ from the  
actual display.  
Item  
Contrast  
Description  
Computer Y/PB/PR  
DVI  
Adjust the image contrast.  
Yes  
Yes  
No  
No  
No  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Display the Setting display menu  
1. Press the MENU button  
2. Select a Category  
Lower  
Brightness Adjust the brightness of the image.  
Darker Brighter  
Adjust the color of the image.  
Lighter Deeper  
Adjust the tint of the image color.  
Reddish Greenish  
Sharpness Adjust the sharpness of the image.  
Softer Sharper  
Set the function to reduce screen noise. No  
On (Enable) Off (Disable)  
Press . Toggle the picture mode with  
Higher  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
No  
No  
Yes  
Select a category by using  
.
Displays the current  
adjustments and settings of  
selected category.  
Item shown with gray cannot  
be adjusted with the current  
input source.  
There are following four  
categories:  
Color  
Tint *1  
p.29  
Image adjustment menu  
p.30  
p.31  
p.32  
Display setting menu  
Default setting menu  
Status display menu  
Yes  
Yes  
Yes  
Noise  
reduction  
3. Adjustments & Settings  
Press  
to open the menu.  
Picture  
mode  
Yes  
Item  
/
.
Adjustment/Setting Value  
Dynamic/Standard/Theater  
5. End  
Press the MENU  
R-level  
G-level  
B-level  
Adjust red of the image color.  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
button  
Less red  
Adjust green of the image color.  
Less green More green  
Adjust blue of the image color.  
Less blue More blue  
NTSC mode*1 Set the black level with  
US: NTSC (US) mode  
Japan: NTSC (JAPAN) mode  
More red  
These marks signify the  
items can be adjusted/set  
The menu disappears.  
This mark signfy that  
there are options.  
by using  
.
Press  
to display a  
list of options.  
/
button.  
These marks signify the items can  
be selected from the list by using  
.
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to  
After an item is selected, apply it  
[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is  
set to US for other languages.)  
by pressing  
.
The figure shows displays given for operation instructions purposes. As the display  
may differ depending on the item, use the following pages as a reference.  
4. Back  
Return button  
Note  
• Menu adjustments and settings are saved when the power is turned off via the ON/  
STANDBY button. If the power cable is disconnected before this, or the power goes out,  
then the data will not be saved.  
28  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Using the menu (Continued)  
The display setting menu  
Use this menu to set screen display-related items.  
The default setting menu  
This menu shows placement status and other settings.  
Description  
Description  
Zoom  
Item  
Item  
p.19  
Sets projection mode in accordance with Placement Style.  
Projection  
mode  
Screen size  
Full  
4:3  
(Mounted  
from ceiling)  
(Rear mounted  
from ceiling)  
(Standard)  
(Rear)  
Full : This mode is best for squeeze-signal video images.  
4:3 : This mode is best for 4:3-signal video images on the 4:3-size screen.  
Zoom : This mode is best for video images of letter-box or cinema signals.  
No signal  
power off  
Set the timer to wait for the power to be turned off after signal input stops.  
Press . Switch with and  
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.  
.
Language  
Select one of the languages below to use for displaying the menu and messages  
[
: Enter setting mode]  
English/Français/Deutsch/Italiano/Español/Português/  
Svenska/Türkçe/  
[
:Selection]  
[Apply:  
]
Auto input  
search  
Set whether the input with signals is only selected or not.  
/
On  
Off  
/
/
/
Power on  
Sets whether to turn on the power when the ON/STANDBY button is pressed  
Background  
Icon  
Screen to display when there is no input signal  
(Logo) (Blue)  
(Manual), or when the power cord is plugged in (Auto). Manual  
Auto  
Standard  
High  
(Black)  
On  
Lamp power [Note 1]  
Fan mode [Note 2]  
Reset all  
Sets the lamp power.  
Low  
Display icons as function guides  
Off  
Off  
Standard  
Sets the cooling fan speed.  
Start-up screen Display start-up screen when power is turned on On  
Press  
.
Yes  
No  
Resets all adjustments and settings to their factory settings.  
Screen size  
The screen size of this unit is 16:9, but the screen size can be changed according to  
the input signal.  
Notes  
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets  
quieter.  
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,  
for example, at high altitude (over 1,500 meters above sea level).  
Note  
• Using these functions to change the picture size (i.e., changing the height/width  
ratio) for any purpose other than your private viewing may be prohibited under the  
Copyright Laws of the United States and other countries, and may subject you to  
civil and criminal liability.  
Notes  
Note that in the event of a power outage but the power is restored afterwards, the projector  
Projection screen  
4:3 signal  
Input signal  
4:3 signal  
power will come on if Power on is set to Auto.  
Full  
Zoom  
• When you turn off the projector even if Power on is set to Auto, you must press the ON/  
STANDBY button to turn the power off.  
Squeeze signal  
Letter box signal  
Cinema signal  
Full (O)  
Full  
4:3  
4:3  
4:3  
Zoom  
Zoom (O)  
Zoom (O)  
Full  
(O): Optimum screen size  
Notes  
The screen size cannot be changed when the 16:9 signal is input.  
You cannot select “Zoom” when the input is COMPUTER or DVI.  
30  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Maintenance  
Using the menu (Continued)  
About lamp  
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure  
to fully understand the following characteristics of the lamp and handle it with extreme care.  
• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at  
the expiration of its life.  
• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.  
Some may burst shortly after first use.  
• Burst is likely to happen if the lamp is used after the replacement period has elapsed.  
• When the lamp bursts, the broken pieces of glass may get inside the product or be  
released outside from the openings for ventilation.  
• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with  
glass dust may be released from the openings for ventilation.  
Displaying Information (Status display)  
This displays information about the input signal, lamp use time, etc.  
Yes”: displayed, “No”: not displayed  
Video  
S-video  
Yes  
No  
No  
No  
No  
No  
No  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Item  
Description  
Computer Y/PB/PR  
DVI  
Input  
Input source name  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
No  
No  
No  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Mode name  
H-resolution  
V-resolution  
H-frequency  
V-frequency  
Sync  
Signal format  
Video mode  
Lamp time  
RGB input mode [Note 1]  
Horizontal resolution (in dots)  
Vertical resolution (in dots)  
Horizontal sync frequency  
Vertical sync frequency [Note 2]  
Sync signal polarity [Note 3]  
Y/PB/PR signal format  
Immediately replace the lamp when a sign appears on the screen.  
No  
No  
• When the replacement time approaches, a message will appear on the screen.  
• The risk of burst will increase if the lamp is continuously used without being replaced.  
• Frequently check the used hours and prepare spares when the replacement time  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Color method of video signal  
No  
No  
Time of lamp use [Note 4]  
Yes  
Yes  
Yes  
Yes  
Yes  
p.32  
approaches. (Refer to “Status display”.  
)
Lamp reset count The count for lamp replacement Yes  
When the lamp is broken  
Total time  
Version  
The total time that this projector is used Yes  
Firmware version [Note 5]  
Yes  
• If glass components, including a lamp and a lens, should break, handle the broken  
pieces with care to avoid injury and contact your dealer for repair service.  
• In the event of lamp burst, unplug the product from the wall outlet, leave and completely  
ventilate the room. Then, thoroughly clean the area around the projector and discard  
any edible items placed in that area.  
Notes  
1: The mode of supported RGB signals  
2: Same as the refresh rate of the computer signal.  
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].  
p.39  
is shown.  
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as  
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult  
with a store about getting a TLPLMT20 replacement lamp (sold separately) prepared.  
5: [Version] shows the version of the projector’s internal control program. This version is referred  
to for customer service, etc.  
Lamp replacement  
A lamp is consumable supplies. If used for extended periods, images will appear dark, and  
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime  
Note  
of the lamp depends on condition of use.) If this happens, replace it with a new one  
.
• The displayed information will not be refreshed if the status changes. To refresh the  
information, dismiss the display, then display it again.  
WARNING  
If the projector is mounted on a ceiling, request a lamp replacement from your projector dealership.  
• When replacing, always use lamp “TLPLMT20” (sold separately).  
CAUTION  
If you have been using the projector, the lamp will be very hot, and may cause burn injuries  
Wait for the lamp to cool (for longer than 1 hour) before replacing it.  
If the lamp should break, please handle with care to avoid injury due to broken pieces and  
contact your dealer for repair service.  
.
32  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Used Lamps  
Lamp replacement (Continued)  
Unplug power cord.  
1
2
This projector’s lamps contain trace amounts of environmentally harmful inorganic  
mercury. Be careful not to break used lamps, and dispose of them in accordance with  
local regulations.  
Wait until lamp is sufficiently cooled.  
Wait for at least 1 hour.  
3
Remove the lamp cover.  
3
Lamp cover  
1
Loosen the 1 screw, then pull up to the direc-  
tion of the arrow with your fingers as shown to  
remove the lamp cover. Use care to avoid any  
damage to nails and/or tip of your finger(s). If  
you have any difficulty in removal, you can use  
a screwdriver or any other smaller tool for your  
convenience.  
Lens and main unit cleaning  
2
WARNING  
Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership  
Attempting to clean/replace the lamp at a high site by yourself may cause you to fall  
down, thus resulting in injury.  
.
Pull out the lamp.  
Loosen the 2 screws holding the lamp in place,  
and pull up the handle to remove the lamp.  
4
5
1
4
5
Lens cleaning  
• Clean the lens with a commercially available blower and/or  
2
lens cleaner.  
Mount the new lamp.  
Align the orientation, press down until the bottom is  
reached, and lock in place using the two lamp  
locking screws.  
• The lens is easily scratched, so do not rub it with hard objects,  
or strike it.  
Main unit cleaning  
2
• Clean the main unit after unplugging the power cord.  
• Wipe dirt off the main unit gently with a soft cloth.  
• Do not wipe the main unit with a damp cloth. Doing  
so may allow water to get inside, resulting in an  
electric shock or failure.  
• Do not use benzene, thinner and the like as they may  
deform or discolor the unit or damage the paint  
surface.  
Replace the lamp cover.  
Align the cover, and press it in, then tighten the  
screws loosened in step  
no longer loose.  
6
7
1
3
until the lamp cover is  
Reset the lamp timer.  
See the lamp’s manual for instructions on resetting  
the lamp timer.  
• When using a chemically treated cloth, follow the  
precautions included with the cloth.  
Notes and Precautions  
• The Lamp time item in the Status display menu indicates the time of lamp se (as a  
p.32  
rough guide).  
• It is recommended that the lamp be replaced after 2,000 hours of use. When Lamp time  
reaches 2,000 hours, the icon and a message will appear. This display disappears  
when you press button.  
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the  
p.36  
lamp may fail to come on  
, and the lamp’s lifetime may be shortened.  
• Always replace the lamp with a new one.  
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,  
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)  
34  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Others  
Trouble indications  
Before calling service personnel  
The indicator lights inform you of internal abnormalities.  
If you think something is wrong, check the followings before contacting customer service.  
p.36  
Please see “Trouble indications”  
as well.  
No power  
Problem with projector  
If This Happens  
Check  
• Unplug the power cord, and contact your dealer.  
The lamp cover is not properly attached.  
• Is the power cord plugged in? Is it connected to the projector?  
• Is the lamp cover loose?  
No power  
p.34  
p.34  
• Unplug the power cord, and reattach the lamp cover.  
(Off)  
p.36  
• Is the ambient temperature high?  
Power goes out  
during use  
p.36  
• Is the air intake or air exhaust blocked?  
Lamp went out during use, or won’t come on  
Lamp temperature is high so that it is difficult to turn on, the lifetime of  
p.23  
• Is the projector turned on?  
• Is the mute function on?  
No picture  
the lamp has ended or the projector is malfunctioning.  
(Red lit)  
p.27  
Unplug the power cord and wait for a short while, then turn the power back on.  
p.29  
• Is the brightness setting minimized?  
• Are the connections set up correctly?  
• If a lamp burns out, replace it with a new one.  
p.20  
After approx. one minute of abnormal display, the projector returns to  
the standby state waiting for internal cool down.  
(Red lit)  
• Are all the connected devices functioning properly?  
p.39 p.40 p.41  
Power went out during use  
Internal overheating, or the outside temperature is too high.  
• Place the projector so that the air intake and exhaust are not blocked.  
• Is the input signal supported by the projector?  
,
,
Picture not  
displayed  
correctly  
(Red lit or flashing)  
Or (Orange lit)  
• Is there something generating an abnormal video signal, for  
instance the video tape?  
(Green lit)  
Unplug the power cord and wait for a short while, then turn the power back on.  
The icon will appear before the power goes out.  
After approx. one minute of abnormal display, the projector returns to  
the standby state waiting for internal cool down.  
p.35  
• Is the lens dirty?  
• Is the lens focus adjusted optimally?  
Picture blurred  
Part of picture  
out of focus  
p.24  
(Red lit)  
• Is the projection distance within the projector’s supported range?  
p.19  
Power went out during use  
Problem with internal cooling fan.  
• Unplug the power cord, and contact your dealer.  
p.19  
• Is the projector’s screen placement angle tilted too far?  
(Red lit or flashing)  
Or (Orange lit)  
p.26 p.29  
• Are the sharpness or sampling phase adjustments off?  
The  
icon will appear before the power goes out.  
p.29  
• Are the brightness or contrast adjustments off?  
After approx. one minute of abnormal display, the projector returns to  
the standby state waiting for internal cool down.  
Image is dark  
p.32  
(Red lit)  
• Is the lamp nearing the end of its service life?  
p.29  
• Are the color, tint, R-level, G-level, or B-level adjustments off?  
• Is the screen dirty?  
• Is the lamp nearing the end of its service life?  
Power went out during use  
Colors too light  
Bad shading  
Problem inside the projector.  
(Green lit  
or Off)  
Unplug the power cord and wait for a short while, then turn the power back on.  
(Green lit  
or Off)  
(Green  
flashing)  
p.32  
• If the above action will not clear the problem, unplug the power cord,  
and contact your dealer.  
• Are the remote control’s batteries drained?  
Remote control  
doesn’t work  
After approx. one minute of abnormal display, the projector returns to  
the standby state waiting for internal cool down.  
p.18  
• Are the batteries inserted into the remote control correctly?  
• Is the remote control being used within the effective range?  
• Are there any obstructions between the remote control and  
projector?  
(Red lit)  
p.18  
PRECAUTION  
• Make sure to unplug the power cord if something goes wrong.  
• Are there any fluorescent or other bright lights shining at the  
projector’s infrared remote sensor?  
36  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Specifications  
List of general specifications  
List of supported signals (RGB signals)  
This projector supports the following RGB signals. Note, however, that depending on the  
Item  
Specification  
computer model, the screen may show flicker or streaking. Please adjust the projector if  
Consumption Power  
Weight  
External Dimensions  
(including protruding parts)  
Cabinet material*  
Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%  
Display pixels  
Picture elements  
Lens  
Lamp  
Projection screen size  
Projection distance  
COMPUTER terminal  
DVI-D terminal  
Y terminal  
300 W  
2.8 kg  
this happens.  
p.25 p.26  
(Press the SET UP button, and adjust automatically or manually.  
,
)
298 × 101.4 × 275.4 mm (W × H × D)  
Refresh rate  
(Hz)  
H-frequency  
Clock  
(MHz)  
PC+ABS resin and ABS resin  
Resolution  
Mode  
(kHz)  
720 x 400  
640 x 480  
720x400_85  
VGA_60  
VGA_72  
VGA_75  
VGA_85  
SVGA_56  
SVGA_60  
SVGA_72  
SVGA_75  
SVGA_85  
MAC16"  
85.039  
59.940  
72.809  
75.000  
85.008  
56.250  
60.317  
72.188  
75.000  
85.061  
74.550  
60.004  
70.069  
75.029  
84.997  
74.700  
75.000  
60.000  
85.002  
60.020  
75.025  
85.024  
60.012  
37.927  
31.469  
37.861  
37.500  
43.269  
35.156  
37.879  
48.077  
46.875  
53.674  
49.725  
48.363  
56.476  
60.023  
68.667  
60.134  
67.500  
60.000  
85.938  
63.981  
79.976  
91.146  
63.973  
35.500  
25.175  
31.500  
31.500  
36.000  
36.000  
40.000  
50.000  
49.500  
56.250  
57.283  
65.000  
75.000  
78.750  
94.500  
79.857  
108.000  
108.000  
148.500  
108.000  
135.000  
157.500  
118.094  
1 chip DMD™  
589,824 pixels (1024H × 576V)  
Zoom lens  
High-pressure mercury lamp  
35.66-285.89 inches  
F=2.5-2.8 f=22.25-26.69 mm  
800 x 600  
1.50-10.00m  
Mini D sub 15 pin Analog RGB  
DVI connector Digital RGB  
RCA Pin Jack, 1V(p-p), 75 Ω  
RCA Pin Jack, 0.7V(p-p), 75 Ω  
RCA Pin Jack, 0.7V(p-p), 75 Ω  
RCA Pin Jack, 1 V (p-p), 75 Ω  
Mini DIN 4 pin  
PB/CB terminal  
PR/CR terminal  
VIDEO terminal  
S-VIDEO terminal  
CONTROL terminal  
832 x 624  
1024 x 768  
XGA_60  
XGA_70  
XGA_75  
XGA_85  
Mini DIN 8 pin (RS-232C)  
MAC19"  
Note  
1152 x 864  
1280 x 960  
SXGA1_75  
QuadVGA_60  
QuadVGA_85  
SXGA3_60  
SXGA3_75  
SXGA3_85  
SXGA+  
• This model complies with the above specifications.  
• Designs and specifications are subject to change without notice.  
• This model may not be compatible with features and/or specifications that may be added  
in the future.  
1280 x 1024  
1400 x 1050  
Separately sold product  
Replacement Lamp  
Model TLPLMT20  
Note  
• Signals which resolution exceeds the native resolution (1024 × 576 pixels) will be  
compressed. For this reason, some information may be lost, or image quality may be  
affected.  
38  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Specifications (Continued)  
List of supported signals (DVI signals)  
List of supported signals (Y/PB/PR signals)  
This projector supports the following DVI signals. Note, however, that depending on the  
computer model, the screen may show flicker or streaking. Please adjust the projector if  
this happens.  
Signal format  
fh(kHz)  
15.73  
31.47  
15.63  
31.25  
45.00  
37.50  
33.75  
28.13  
fv(Hz)  
59.94  
59.94  
50.00  
50.00  
60.00  
50.00  
60.00  
50.00  
480i(525i)@60Hz  
480p(525p)@60Hz  
576i(625i)@50Hz  
576p(625p)@50Hz  
720p(750p)@60Hz  
720p(750p)@50Hz  
1080i(1125i)@60Hz  
1080i(1125i)@50Hz  
Refresh rate  
(Hz)  
H-frequency  
(kHz)  
Clock  
(MHz)  
Resolution  
640 x 480  
Mode  
59.940  
72.809  
60.317  
72.188  
74.550  
60.004  
70.069  
75.029  
75.000  
60.000  
60.020  
31.469  
37.861  
37.879  
48.077  
49.725  
48.363  
56.476  
60.023  
67.500  
60.000  
63.981  
25.175  
31.500  
40.000  
50.000  
57.283  
65.000  
75.000  
78.750  
108.000  
108.000  
108.000  
VGA_60  
VGA_72  
SVGA_60  
SVGA_72  
MAC16"  
XGA_60  
XGA_70  
XGA_75  
800 x 600  
832 x 624  
1024 x 768  
List of supported signals (Video, S-Video signals)  
Video mode  
NTSC  
fh(kHz)  
15.73  
15.63  
15.63  
15.73  
15.63  
15.73  
15.73  
fv(Hz)  
60  
fsc(MHz)  
3.58  
1152 x 864  
1280 x 960  
1280 x 1024  
SXGA1_75  
QuadVGA_60  
SXGA3_60  
PAL  
50  
4.43  
SECAM  
PAL-M  
50  
4.25 or 4.41  
3.58  
60  
Signal format  
fh(kHz)  
31.47  
31.25  
45.00  
37.50  
33.75  
28.13  
fv(Hz)  
PAL-N  
50  
3.58  
480p(525p)@60Hz  
576p(625p)@50Hz  
720p(750p)@60Hz  
720p(750p)@50Hz  
1080i(1125i)@60Hz  
1080i(1125i)@50Hz  
59.94  
50.00  
60.00  
50.00  
60.00  
50.00  
PAL-60  
NTSC4.43  
60  
4.43  
60  
4.43  
Pin assignment of COMPUTER terminal  
5
1
Pin No.  
Pin description  
Video signal (R)  
Video signal (G)  
Video signal (B)  
GND  
1
2
Note  
3
• Signals which resolution exceeds the native resolution (1024 × 576 pixels) will be  
compressed. For this reason, some information may be lost, or image quality may be  
affected.  
4
10  
15  
6
5
GND  
6
GND (R)  
11  
7
GND (G)  
Mini D sub 15 Pin connector  
8
GND (B)  
9
N.C  
Input Signal  
• RGB input  
RGB signals:  
Horizontal sync signal: TTL level (Pos/neg polarity)  
Vertical sync signal: TTL level (Pos/neg polarity)  
10  
11  
12  
13  
14  
15  
GND  
0.7V (p-p) 75 Ω  
GND  
N.C  
Horizontal sync signal  
Vertical sync signal  
N.C  
40  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English
Specifications (Continued)  
Pin arrangement for the DVI-D terminal  
CONTROL terminal  
Pin assignment  
D V I - D  
Pin No.  
Signal Name  
RXD  
Description  
1
2
3
4
5
6
7
8
Receiving data  
Consent to send  
Data set ready  
Signal ground  
Request to send  
No connection  
Sending data  
7
1
8
CTS  
DSR  
GND  
RTS  
N.C  
8
6
5
3
24  
16  
9 17  
4
TXD  
GND  
2
1
DVI DIGITAL connector  
Signal ground  
Mini DIN 8 pin connector  
Pin No.  
Pin description  
Pin No.  
16  
Pin description  
Hot plug detection  
Interface format  
1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;  
1
2
T.M.D.S. data 2–  
Stop Bit Length: 1 bit  
STX (02h) Command (3Byte) ETX (03h)  
Only 1 command valid per communication.  
For input commands, only ASCII-compliant all-uppercase  
alphanumeric characters supported.  
T.M.D.S. data 2+  
17  
T.M.D.S. data 0–  
T.M.D.S. data 0+  
T.M.D.S. data 0/5 shield  
T.M.D.S. data 5–  
T.M.D.S. data 5+  
T.M.D.S. clock shield  
T.M.D.S. clock+  
2 Communication format  
3 Data format  
3
T.M.D.S. data 2/4 shield  
T.M.D.S. data 4–  
18  
4
19  
5
T.M.D.S. data 4+  
20  
6
DDC clock  
21  
4 Replies  
Acknowledge  
ACK (06h) CR (0Dh) Data ... Normally ended  
7
DDC data  
22  
ACK (06h) ESC (1Bh)  
NAK (15h)  
... Aborted  
8
Analog vertical sync signal  
T.M.D.S. data 1–  
23  
No acknowledge  
9
24  
T.M.D.S. clock–  
10  
11  
12  
13  
14  
15  
T.M.D.S. data 1+  
If commands are to be sent consecutively, wait for the response from the projector  
before sending the next command.  
T.M.D.S. data 1/3 shield  
T.M.D.S. data 3–  
Main Commands  
Item  
Command  
IN1  
Item  
Command  
PON  
T.M.D.S. data 3+  
Computer input select  
DVI input select  
Power on  
Power off  
Icon display on  
+5V power supply  
GND(+5V, H Sync & V Sync)  
IN2  
PSD  
Video input select  
S-video input select  
YPB/CBPR/CR input select  
IN3  
IN4  
IN5  
MO0  
MO1  
PAT  
DON  
Icon display off  
Auto setting (RGB input)  
Status display on  
Status display off  
DOF  
Note  
• Contact your dealer for control cable and other commands.  
42  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Texas Instruments Network Card UCC38500EVM User Manual
Timex Watch WS4 User Manual
Topcom Telephone 2500 Duo User Manual
Trane Microphone DX1B040A9H21B User Manual
Tricity Bendix Refrigerator TB 25 TR User Manual
UNICOM Electric Network Card POE 22001T User Manual
ViewSonic Computer Monitor VX2255WMB User Manual
Vivotek Security Camera IP6114 User Manual
Vulcan Hart Electric Steamer ES25 ML 52642 User Manual
Waste King Garbage Disposal WLC 100 User Manual