NPS10A/NPX10A
DATA PROJECTOR
USER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No.
Serial No.
Retain this information for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
3. Source of Light
6. Water and Moisture
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
Do not use this product near
water. - for example, near a bath
tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or
near a swimming pool and the like.
4. Ventilation
7. Cleaning
Openings in the cabinet are pro-
vided for ventilation and to ensure
reliable operation of the product
and protect it from overheating.
These openings must not be
blocked or covered. Never block
an opening by placing the product
on a bed, sofa, rug or other similar
surface. Do not place it in a built-in
installation such as a bookcase or
rack, unless proper ventilation is
provided.
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol clean-
ers. Always use a soft cloth for
cleaning.
8. Besure that you fimly
insert the plug into the
wall outlet.
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
5. Heat
The product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including ampli-
fiers) that produce heat.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
9. Power Cord Protection
11. Lightning storms
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them, pay-
ing particular attention to cords at
plugs, convenience receptacles,
and the point where they exit from
the product.
For added protection for this
product during a storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/or
peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
10. Overloading
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord, receptacle, or
other outlet unless the blades can
be inserted completely with three-
wire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in fire
or electric shock.
12. Object and Liquid Entry
Never push objects of any kind
into this product through open-
ings as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock. Never spill liquid of any
kind on the product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
14. Do not place the product
vertically
17. Accessories
Do not place this product on an
unstable cart, stand, tripod, brack-
et, or table. The product may fall,
causing serious injury to a child or
adult, and serious damage to the
product. A product and cart combi-
nation should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
Do not use the product in the up-
right position or any other vertical
positions to project the pictures. It
may fall which could result in seri-
ous injury and/or damage to the
product.
15. Stack Inhibited
S3125A
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may dam-
age the other unit.
18. Damage Requiring Service
Unplug this product from the wall
outlet and take the product to
qualified service personnel if you
encounter any of the following
conditions:
a) The power supply cord or plug is
damaged.
b) Liquid has been spilled, or objects
have fallen into the product.
c) The product has been exposed to
rain or water.
d) The product does not oper-
ate normally when following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions since an
improper adjustment of other con-
trols may result in damage and will
often require extensive work by a
qualified technician to restore the
product to its normal operation.
16. Attachments
Do not use attachments not rec-
ommended by the product manu-
facturer. Use of an incompatible
attachments could cause hazards
or damage to the product.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
e) The product has been dropped or
21. Replacement Parts
damaged in any way (If the cabi-
When replacement parts are re-
net should break, please handle
quired, be sure the service techni-
with care to avoid injury).
cian has used replacement parts
f) The product exhibits a distinct
specified by the manufacturer or
change in performance, which
have the same characteristics as
indicates a need for service.
the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
19. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
22. Safety Check
Upon completion of any service or
repairs to this product, ask the ser-
vice technician to perform safety
checks to verify that the product is
in proper operating condition.
This product incorporates glass
components, including a lens and
a lamp. If these should break,
please handle with care to avoid
injury and contact your dealer for
repair service. Avoid any broken
pieces of glass since they may
cause injury. In the unlikely event
that the lamp ruptures, thoroughly
clean the area around the projec-
tor and discard any edible items
placed in that area since they may
be contaminated.
23. Do not leave thermal-
paper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods
of time.
20. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other haz-
ards. Refer all servicing to quali-
fied service personnel.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
24. Do not use the product
in a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may over-
heat, which could result in a risk
of fire.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm
location. When the unit is exposed to such a change in temperature, moisture may
condense on the lens and the crucial internal parts. Do not use the unit for at least 2
hours when there is an extreme or sudden change in temperature to prevent the unit
from possible damage.
Place and Manner of Installation
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, short-
ening their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20°
from level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or
audio sound. If this happens, move it away from the TV or radio.
Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts. If you continue to use it in that situa-
tion it may malfunction. Wait until the condensation naturally disappears.
In a high altitude location where air is thin, cooling efficiency is reduced so use the
ꢀ
p.34
projector with [High Altitude] set to [On].
ꢀ
ꢀ
ꢀ
The set of projector is hot after use. Handle with care.
Do not use the projector while holding it in your hands or lap.
Do not use the projector near a power source and the like, or in locations like a ship
or vehicle that are subject to vibration or shock. Doing so may lead to a malfunction or
shorten service life.
ꢀ
Only plug the power cord into outlets rated for use with the power cord’s specified
voltage range. Do not overload extension cords or power strips as this can result in
fire or electric shock.
ꢀ
ꢀ
Route the power cable or the connecting cable away from where people could trip
over it. The projector may fall, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber
or plastic products touching the unit for a long time, as they will leave marks on the
finish. Do not use a chemically saturated cloth.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EXEMPTION CLAUSES
ꢀ
Toshiba Corporation bears no responsibility in the case of damages arising from natu-
ral disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,
acts by third parties, other accidents, or use under abnormal conditions including
erroneous or improper operation and other problems.
ꢀ
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or
the inability to use this unit.
ꢀ
ꢀ
Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this User’s Manual.
Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related
to Toshiba Corporation.
OTHER INFORMATION
Copyright
© 2011 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this
manual cannot be reproduced in any form without the prior written permission of
TOSHIBA. No patent liability is assumed, with respect to the use of the information
contained herein.
Showing or transmitting commercial imaging software or broadcast or cable-broad
casting programs with the purpose of other than the personal and private viewing,
including modifying images using the freeze functions, or displaying with the vary-
ing aspect ratio of the images, could violate the direct or indirect copyrights of the
imaging software or broadcast program, etc., if done without first consulting with the
copyright holder. For this reason, take appropriate measures before performing one
of the actions listed above, including obtaining a license from the copyright holder.
Disclaimer
This manual has been validated and reviewed for accuracy. The instructions and
descriptions it contains are accurate for your computer at the time of this manual’s
production. However, succeeding computers and manuals are subject to change with-
out notice. TOSHIBA assumes no liability for damages incurred directly from errors,
omissions or discrepancies between the computer and the manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER INFORMATION (Continued)
Trademarks
ꢀ
VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of Interna-
tional Business Machines Corporation.
ꢀ
ꢀ
ꢀ
DLP (Digital Light Processing) is a registered trademark of Texas Instruments, Inc.
Macintosh is a registered trademark of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation in the U.S. and other
countries.
ꢀ
ꢀ
Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorpo-
rated.
All other brand and product names are trademarks or registered trademarks of their
respective companies.
Notational Conventions Used in This Manual
ꢀ
References to pages with related information are annotated as follows.
For example, if making a reference to page 32:
p.32
ꢀ
The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
REMOTE CONTROL BATTERY
Warning
ꢀ
ꢀ
Never throw a battery into a fire.
Using the battery improperly may cause them to explode or leak and may result in
serious injury. If battery-leaking fluid contacts skin, wash the fluid off immediately with
clean water and consult a doctor. If the fluid spills on an instrument, avoid contact and
wipe it off using tissue paper. Then dispose of the used tissue paper as flammable
garbage after moistening it with water.
ꢀ
Keep the battery away from the reach of children. Battery is choking hazard and can
be very dangerous if swallowed. If the battery is swallowed, seek medical assistance
immediately.
Notes
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Be sure to use a CR2025 battery.
Dispose of a battery in a designated disposal area.
Check and follow your local regulations before disposal.
Attention should be drawn to the environmental aspects of battery disposal.
If the remote control does not operate correctly, or if the operating range becomes
reduced, replace the battery with a new one.
ꢀ
If the battery is dead or if you will not be using the remote control for a long time,
remove the battery to prevent battery acid from leaking into the battery compartment.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Before Using
SAFETY INFORMATION..............................................................................................2
IMPORTANT SAFETY INSTRUCTIONS......................................................................2
IMPORTANT PRECAUTIONS......................................................................................7
EXEMPTION CLAUSES...............................................................................................8
OTHER INFORMATION ...............................................................................................8
REMOTE CONTROL BATTERY ..................................................................................9
PrCeOpNaTrEaNTtiSo..n....s..........................................................................................................10
Checking the package contents..................................................................................12
Names of each part on the main unit..........................................................................13
Names of each part on the control panel....................................................................14
Names of each part on the remote control..................................................................15
Parts on the rear panel ...............................................................................................17
Preparing and using the remote control......................................................................18
Placement...................................................................................................................19
Connection..................................................................................................................21
Operations
Turning the power on and off......................................................................................22
Basic operations .........................................................................................................24
Using the handy features............................................................................................26
Using auto setting (For computer input only) ........................................................26
Correcting the keystone distortion.........................................................................26
Cutting off the picture and sound temporarily (Mute)............................................27
Freezing the image (Freeze).................................................................................27
Changing picture mode.........................................................................................27
Resizing image......................................................................................................28
Using the menus.........................................................................................................29
How to use the menus...........................................................................................29
The image adjustment menu.................................................................................30
The screen setting menu.......................................................................................32
The default setting menu.......................................................................................33
The options setting menu......................................................................................34
Maintenance
About lamp..................................................................................................................35
Lamp replacement......................................................................................................36
Lens and main unit cleaning.......................................................................................38
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS (Continued)
Others
Trouble indicators .......................................................................................................39
Before calling service personnel.................................................................................40
Specifications..............................................................................................................41
List of general specifications.................................................................................41
List of supported signals (RGB signals)................................................................42
List of supported signals (HDMI)...........................................................................43
List of supported signals (Video)...........................................................................44
Pin assignment of COMPUTER IN terminal..........................................................45
SERIAL terminal....................................................................................................45
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the package contents
Please make sure that the following items are included in the box, along with the main
unit. If any item is missing, immediately contact the store where you purchased the prod-
uct.
(1)
(3)
(4)
(5)
(2)
(6)
ꢁ (1) Remote control
ꢁ (2) CD-ROM (User’s Manual)
ꢁ (3) Quick Start Guide
ꢁ (4) RGB cable (See note below)
ꢁ (5) Power cord (See note below)
ꢁ (6) Bag
Notes
ꢀ
ꢀ
The shape and number of supplied power cords vary depending on the product desti-
nation.
To maintain original performance, always use the supplied cables.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever
have to ship your projector. For maximum protection when shipping your projector,
repack the set as it was originally packed at the factory.
ꢂ The Supplied CD-ROM
The supplied CD-ROM contains the user’s manual in Portable Document Format (PDF).
Please use Acrobat Reader 5 or later version to view the manual.
ꢃ Adobe® Acrobat® Reader® or Adobe® Reader®
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF
files, please install Adobe Reader software in your computer by downloading it from
the Adobe Systems website.
ꢃ Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader® launches, and the
menu screen of the user’s manual appears. Click on your language. The User’s Man-
ual cover and list of bookmarks appear. Click on a bookmark title to view that section
of the manual. See the Help menu for more information about Acrobat® Reader®.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the main unit
(6) (5)
(4)
(3)
(2) (1)
(7)
(8)
(9)
(10)
(11)
(11) (12) (13)
Front
Back
Name
: Function
(1) Lens
: Projects expanded image.
(2) Infrared remote sensor
: Senses commands from the remote control.
p.18
(3) Air exhaust
(4) Air intake
: Expels hot air out of the projector.
: Draws in air from outside the projector for
internal cool down.
p.14
(5) Control panel
(6) Zooming ring
(7) Speaker
: Operates the projector.
p.25
: Adjusts screen size.
: Outputs audio sound.
p.22
(8) AC IN socket
(9) Rear panel
: Connect the supplied power cord here.
p.17
: Connects external devices.
(10) Antitheft lock slot
: Attach a safety cable or any other antitheft
device.
p.25
(11) Tilt adjuster
(12) Foot adjuster
(13) Focusing ring
: Adjusts the projector’s horizontal tilt.
p.25
: Adjusts the vertical projection angle.
p.25
: Adjusts screen focus.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the control panel
zoom
(1)
Name
: Main Function
p.22
(1) ON/STANDBY button/
indicator
: Turns the power on/off (standby).
p.22
: Displays power on/off mode.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the remote control
Remote control
transmitter
(1)
(17)
(16)
(15)
(14)
(2)
(3)
(4)
(5)
(6)
(13)
(7)
(4)
(8)
(12)
(11)
(9)
(10)
Name
: Main Function
p.22
(1) ON/STANDBY button
(2) IMAGE button
: Turns the power on/off (standby).
p.27
: Changes picture mode.
(3) COMPUTER button
(4) KEYSTONE +/- button
(5) FREEZE button
(6) ENTER button
: Selects COMPUTER input source.
p.26
: Adjusts keystone distortion.
p.27
: Pauses image.
: Accepts the selected mode.
p.24
(7) INPUT button
: Selects input source.
p.29
(8) MENU button
: Displays menus.
(9) AV-MUTE button
: Momentarily turns off/on the audio and video.
p.27
(10) VOLUME +/- button
: Adjusts the volume.
(11) INPUT SEARCH button
: This function detects the input signal
automatically. When finding a signal, the search
p.24
will stop.
(12) AUTO ADJ. button
: Performs auto-adjustment of input signals from
p.26
computer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the remote control (Continued)
Name
: Main Function
(13) D. ZOOM button
: Zoom out or zooms in the projector display.
p.28
p.29
(14) Selection buttons
(15) VIDEO button
(16) S-VIDEO button
(17) RESET button
: Menu selections and adjustments.
: Selects VIDEO input source.
: Selects S-VIDEO input source.
: Resets all adjustments and settings to their
factory settings.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts on the rear panel
(1)
(2)
(3) (4) (5) (6) (7) (8)
COMPUTER-IN
MONITOR-OUT
HDMI
S-VIDEO
VIDEO
SERIAL
AUDIO-IN AUDIO-OUT
(9)
(10)
Name
: Main Function
(1) COMPUTER IN terminal
: Input analog RGB signal from a computer or
other source, or a component video signal
(Y/Pb/Pr) from video equipment.
(2) MONITOR OUT terminal
(3) HDMI terminal
: Connect to a computer display, etc.
: Input HDMI (Digital Audio/Video) signal from
video equipment.
(4) S-VIDEO terminal
(5) VIDEO terminal
(6) SERIAL terminal
(7) AUDIO IN terminal
(8) AUDIO OUT terminal
(9) AC IN socket
: Input S video signals from video equipment.
: Input video signals from video equipment.
: Maintenance use only.
: Input audio signals.
: Outputs audio signals.
: Connect the supplied power cord here.
(10) Antitheft lock slot
: Attach a safety cable or any other antitheft
device.
Notes
ꢀ
HDMI terminal is NOT supported for NPS10A.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control
ꢃ Loading a coin cell battery into the
Notes
remote control
ꢀ
When you use for the first time after
purchase, a plastic sheet is provided
between the battery and its contact.
Be sure to remove by pulling it off.
When operating the remote control
from behind the projector, the infrared
beam is reflected on the projecting
surface and may travel a shorter dis-
tance to reach the projector depend-
ing on the shape and material of the
projecting surface.
Remove the battery holder.
ꢀ
Hold down the side release firmly and
pull out the battery holder.
ꢀ
Load a coin cell battery (CR2025).
Be sure to align the plus and minus
ends of the battery properly.
ꢁ
ꢃ Operating the remote control
5
2
0
T
ꢀ
Point toward the projector’s infrared
remote sensor, and press a button on
the remote control.
L
O
CR2
3
V
ꢀ
Operating the projector from the front
Replace the battery holder back into
the remote control.
ꢂ
Approx.15°
5
2
0
2
T
L
R
O
C
V
3
ꢃ Coin cell battery
ꢀ
Before using the battery, be sure to observe the Safety Precautions described in
previous pages.
ꢀ
ꢀ
Remove the battery from remote control when not using for extended periods.
If the remote control stops working, or if its range decreases, replace the battery with
a new one.
ꢀ
Keep the battery away from the reach of children. Battery is choking hazard and can
be very dangerous if swallowed. If the battery is swallowed, seek medical assistance
immediately.
ꢃ The remote control
ꢀ
The remote control may fail to operate if the infrared remote sensor is exposed to
bright sunlight or fluorescent lighting.
Do not drop or bang.
Do not leave in hot or humid locations.
Do not allow it to get wet or place it on top of wet objects.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Do not take apart.
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the opera-
tion.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Mounting] in the Default
p.33
setting menu.
Floor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection
Ceiling-mounted rear projection
WARNING
ꢀ
ꢀ
Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. At-
tempting to clean or replace the lamp in a high location by yourself may cause you to fall, resulting in injury.
If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector
on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting
could cause the projector to fall, resulting in an accident.
ꢀ
If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement (Continued)
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and pro-
jection distance. (Projection sizes are approximate values for full-size picture with no
keystone adjustment.)
Wide
Tele
Offset
As seen from above
Projection
size
distance (a)
distance (a)
height (H)
(inches)
(m)
(feet)
3.90
5.20
7.80
9.10
(m)
1.31
1.75
2.62
(feet) (cm) (feet)
Screen
30
40
1.19
1.58
2.38
2.77
4.30
5.73
6.86
9.14
0.22
0.30
90
60
8.60 13.72 0.45
70
3.06 10.03 16.00 0.52
80
3.17 10.40 3.50 11.46 18.29 0.60
3.57 11.70 3.93 12.90 20.57 0.67
3.96 13.00 4.37 14.33 22.86 0.75
4.75 15.60 5.24 17.20 27.43 0.90
5.94 19.50 6.55 21.49 34.29 1.12
7.13 23.39 7.86 25.79 41.15 1.35
9.91 32.49 10.92 35.82 57.15 1.87
11.89 38.99 13.11 42.99 68.58 2.25
As seen from the side
90
100
120
150
180
250
300
Lens center
H
90
a
a is the distance (m, feet) between the lens and the screen, and corresponds to a range
of 1.19 m to 11.89 m (3.90 ft. to 38.99 ft.). H is the height (cm, feet) from the image bot-
tom to the center of the lens.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Before connection
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Read the user’s manual of the device you are connecting to the projector.
Some computers cannot be used with or connected to this projector.
Check for an RGB output terminal, supported signal, etc.
Turn off the power of both devices before connecting.
The figure below shows sample connections. This does not mean that all of these
devices can or must be connected simultaneously.
Computer
Computer
Monitor
To RGB
output
To audio
output
To audio
RGB cable
(supplied)
Audio cable
(not supplied)
To RGB output
Audio cable
(not supplied)
output
RGB cable
(not supplied)
To audio input
White (L)/Red (R)
Audio cable
(not supplied)
COMPUTER-IN
MONITOR-OUT
HDMI
S-VIDEO
VIDEO
SERIAL
AUDIO-IN AUDIO-OUT
To HDMI
output
To video
To YPbPr
output
HDMI cable (not supplied)
output
Video cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To audio
output
To S-video output
S-Video cable
(not supplied)
Audio cable
Audio amplifier, etc.
(not supplied)
Conversion
adapter BNC-pin
(not supplied)
DVD video recorder,
DVD player, etc.
Video recorder,
DVD player, etc.
Video recorder, etc.
Notes
ꢀ
ꢀ
Moving pictures played back on computers using DVD software may appear unnatural
when projected with this projector. However, it is not a malfunction of the projector.
When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
ꢀ
ꢀ
Output volume of AUDIO OUT terminal can be adjusted by the VOLUME+/- button.
The MONITOR OUT terminal outputs analog RGB signals or component video signals
(Y/Pb/Pr) from the COMPUTER IN terminal.
ꢀ
A computer monitor usually cannot accept Y/Pb/Pr signals correctly.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the power on and off
ꢃ Connecting the power cord
Insert the power cord connector into
the AC IN socket of the projector.
1
Insert the power cord plug into a wall
or other power outlet.
2
Power cord connector
(Supplied)
ꢃ Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If the cover is left on the projector, it could
become deformed due to heat.
ꢃ Turning the power on
Control panel
Remote
Control
Start-up screen
Press the ON/STANDBY
1
button.
The power is turned on, and the ON/
STANDBY indicator lights blue. After a
moment, the start-up screen appears.
zoom
CAUTION
ꢀ
Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your
eyesight.
ꢀ
ꢀ
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the bottom of the
unit. Doing so could result in injury and/or damage the object.
Notes
ꢀ
The start-up screen will disappear after a moment. You can also configure the system
to prevent the start-up screen from appearing. To do this, use the Default setting
p.33
menu.
ꢀ
ꢀ
The first time you use the projector after purchase, after the start-up screen disap-
pears, the start menu is displayed.
Do not touch the lens directly with your hand. If fingerprints or stains are left on the
projection lens surface, they may interfere with the projector’s ability to project images
on the screen.
p.24
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the power on and off (Continued)
ꢃ Turning the power off
Press the ON/STANDBY button.
1
A message appears on the screen, confirming that you wish to shut off the power.
To shut off the power, press the ON/STANDBY button again. If you do not wish to
shut off the power, wait for a while without conducting any operations. The message
will disappear shortly. (This operation is no longer valid after the message disap-
pears.)
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short
while. Then, the projector goes into standby mode.
2
When cooling lamp
After cooling complete
A
B
During cooling ,the ON/STANDBY indicator flashes. In this state, the power
cannot be turned back on.
A
However, there is no problem with unplugging the power cord in this state.
In standby mode
B
Notes
ꢀ
The projector consumes about 0.5W of power in standby. We recommend that you
unplug the power cord if you will not be using the projector for an extended period.
Precaution
ꢀ
ꢀ
If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
Right after turning off the power, the unit may become very hot, especially air exhaust
and the bottom of the unit. Please handle with care to avoid burn injuries.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
Turn the power.
1
p.22
Turn on the power by following the instructions in “Turning the power on”.
Select the language (When using the first time).
The screen turns off, but the internal cooling fan continues to operate for a short
while. Then, the projector goes into standby mode.
2
Use the
the button.
Message for setup confirmation is displayed in a selected language.
,
,
or
button to select the desired language and press
English
French
Thai
Simplified Chinese
Bahasa Indonesia
Notes
ꢀ
When the projector is turned on the next time, the start menu does not appear upon
startup.
The language can also be set via the Default setting menu.
This user’s manual assumes that English has been selected.
p.33
ꢀ
ꢀ
Activate the connected device.
Turn on and start the connected device such as a computer.
3
Press the INPUT button.
An image of the connected equipment is projected.
4
Each time you press the INPUT button, it switches to another source signal from the
equipment which is connected to the projector.
Notes
p.33
ꢀ
When [Input search] is set to [On] in the Default setting menu
(factory setting
is [On]), the input is switched to the connected equipment that is outputting video
p.42
signals each time you press the INPUT button.
ꢀ
Right after the input source is switched to the other, the color of the image may
change slightly.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations (Continued)
Projector placement angle adjustments.
5
The placement angle and the height of the projected image can be adjusted by the
foot adjuster.
Lift up the front of the projector to the
desired angle, then use the foot adjuster.
ꢀ
ꢁ
ꢁ
To adjust the horizontal angle, use the tilt
adjuster.
ꢀ
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.
ꢀ
ꢁ
ꢀ
Adjusting the screen size and focus.
6
7
Use the zooming ring to adjust the screen size.
ꢀ
Use the focusing ring to adjust the focus.
ꢁ
Adjusting the volume with VOLUME +/- buttons.
The speaker volume can be adjusted when an audio signal is being input.
Notes
ꢀ
Lamp characteristics may rarely cause the brightness to fluctuate slightly.
ꢀ
ꢀ
ꢀ
A lamp is consumable item. If used for extended periods, images will appear dark,
and the lamp could burn out. This is characteristic of a lamp, and is not malfunction.
(The lifetime of the lamp depends on conditions of use.)
The DLP® chip is made using extremely advanced technology. There may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the
panel. These are intrinsic characteristics of the technology and are not malfunctions.
p.42
Although this projector supports a wide range of RGB signals
, any resolutions
not supported by this projector (SVGA, XGA) will be expanded or shrunk, which will
affect image quality slightly. To view high-quality images, set the computer’s external
output to SVGA / XGA.
With some models of computer having LCD displays or the like, displaying images si-
multaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For informa-
tion on how to turn off the LCD display, see the computer’s user’s manual.
If no signal is being input from the connected equipment or signal input is stopped
while projecting, the “No signal” message will appear.
ꢀ
ꢀ
ꢀ
ꢀ
If a signal not supported by the projector is input, the “Unsupported signal” mes-
sage will appear.
If an unavailable operation button is pressed, the
icon will appear.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the handy features
ꢃ Using auto setting (For computer input only)
This function automatically sets up the projector to the optimum state. It
sets up sampling phase, frequency and screen position for each type of
the input signal by using simple operations.
Remote
Control
Press the remote control’s AUTO ADJ. button.
Notes
ꢀ
ꢀ
The image may not be projected or auto adjustment/setting may not
be performed correctly for input signals other than those supported by
the projector.
p.42
If auto setting fails adjustment, adjust manually with Image adjust-
p.30
ment menu.
ꢃ Correcting the keystone distortion
When the projector placement angle against the screen is changed while projecting
the image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion.
Before correction
After correction
Remote
Control
Press the remote control’s KEYSTONE +/- button.
You can also select [V Keystone] in the Screen setting menu.
p.32
Notes
ꢀ
Depending on the amount of keystone adjustment and the content
of images, some information may be lost, or the picture quality may
suffer.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the handy features (Continued)
ꢃ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead pro-
jector, etc. temporarily, this projector’s images and sound can be turned
off.
Remote
Control
Press the remote control’s AV-MUTE button.
The picture and sound are cut off. (The Mute function is released
when pressing the AV-MUTE button again.)
Notes
ꢀ
Operating any other functions will also cancel the muting.
ꢃ Freezing the image (Freeze)
The projected image can be frozen. This function is used to pause a
video during a presentation, etc.
Remote
Control
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released by pressing
the FREEZE button again.)
Notes
ꢀ
ꢀ
Other operations will also release the freeze.
Although an image is frozen on the projector, the pictures are running
on the video or other equipment.
ꢀ
If you use this function on commercial video software, broadcast or
cable-broadcasting except for the purpose of your private viewing and
listening, it may infringe the copyright protected by the copyright laws.
ꢃ Changing picture mode
The projected image mode can be selected.
Remote
Control
Press the remote control’s IMAGE button.
The picture mode menu appears.
1
2
1: Presentation
5: Blackboard
6: Classroom
7: User1
2: Bright
3: Movie
4: sRGB
8: User2
Select a mode using
then press
.
Though the button is not pressed, the picture mode changes as the setting is
changed and the display turns off automatically in a few seconds.
Notes
ꢀ
[Image mode] of the Image adjustment menu has the same function.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the handy features (Continued)
ꢃ Resizing image
The projected image can be resized (zoomed in/out).
Press the remote control’s D. ZOOM and buttons.
Each time you press the button, zoom ratio is up. You can keep
pressing.
1
Remote
Control
2
Press the remote control’s D. ZOOM and buttons.
Each time you press the button, zoom ratio is down. You can
keep pressing. (However, the image cannot be smaller than the original size.)
To move the area to zoom in/out, use the
buttons.
3
4
You can keep pressing.
When the image returns to the original size by pressing D. ZOOM
button several times, the zoom will be reset.
Notes
ꢀ
Operating a function other than AV-Mute will release resizing.
As zooming is processed digitally, the image quality is degraded in
larger zoom ratio.
ꢀ
ꢀ
During resizing or moving the zooming area, the image may be
distorted.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
You can call up on-screen menus, and conduct a number of adjustments and settings
p.15
using the operation buttons on the remote control.
ꢃ How to use the menus
The menu shown below is for operation instructions purposes and might differ from
the actual display.
1. Press the MENU button
Display the Image adjustment menu
2. Select a Category
Select a category by using
There are following 4 categories:
.
Displays the current
adjustments and settings
of selected category. Item
shown with gray cannot
be adjusted with the cur-
rent input source.
p.30
Image adjustment menu
p.32
Screen setting menu
p.33
Default setting menu
p.34
Options setting menu
Press the
or
button.
3. Adjustment & Settings
Item
Adjustment/Setting Value
These marks signify the
items can be adjusted/
set by using
.
These marks signify the items
can selected from the list by
using
.
After an item is selected,
apply it by pressing
.
The figure shows displays given for operation instructions purposes. As the display may differ depending
on the item, use the information in this manual as a reference.
4. Back
Press the Menu Button
5. End
Press the Menu Button again. The menu disappears.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
ꢃ The image adjustment menu
Use this menu to set or adjust image-related items. Items that can be set or adjusted are
marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it
indicates that you cannot select for the current input.)
Description
RGB Y/Pb/Pb Video S-video HDMI
Item
Image Mode
Toggle the picture mode with Yes
/
Yes
Yes
Yes
Yes
Presentation/Bright/
Movie/sRGB/Blackboard/
Classroom/User 1/User 2
Brightness
Adjust the brightness of the
image.
Yes
Yes
Yes
Yes
Yes
Darker
Adjust the image contrast.
Lower Higher
Brighter
Contrast
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Sharpness
Adjust the sharpness of the
image.
Softer
Sharper
Saturation
Tint
Adjust the saturation of the
image.
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Unsaturated
Saturated
Adjust the tint of the image
color.
Reddish
Greenish
Advanded
Gamma
Toggle the gamma type with
/
Yes
Yes
Yes
Yes
Yes
Film/Video/Graphics/PC
BrilliantColor™ This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while providing
true, more vibrant colors in picture. The range is from “0” to “10”. If you
prefer a stronger enhanced image, adjust toward the maximum setting.
For a smoother, more natural image, adjust toward the minimum setting.
Color Temp.
Toggle the color temperature with
Low/Medium/High
/
.
(At higher temperature, the screen looks colder; at lower temperature,
the screen looks warmer.)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
Description
RGB Y/Pb/Pb Video S-video HDMI
Item
Color
Adjust the color of the
image.
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Red/Red Gain
/
/
/
Lighter
Green/Green Gain
Lighter Deeper
Blue/Blue Gain
Deeper
Lighter
Deeper
Cyan
Lighter
Deeper
Deeper
Deeper
Magenta
Lighter
Yellow
Lighter
Color Space
Input
Select an appropriate color
matrix type with
/
AUTO/RGB/YUV
Use this option to enable/
disable input sources.
Yes
Yes
Yes
Yes
Yes
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
ꢃ The screen setting menu
Use this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
Description
Item
Aspect Ratio
Screen size setting.
4:3: This format is for 4x3 input sources.
AUTO: Automatically selects the appropriate display format.
16:9: This format is for 16x9 input sources, like HDTV and DVD
enhanced for widescreen TV.
16:10: This format is for 16x10 input sources, like widescreen laptop.
Native: This format displays the original image without any scaling.
Overscan
Overscan function removes the noise in a video image. Overscan the
image to remove video encoding noise on the edge of video source.
D. Zoom
Adjust the size of projected image.
Minify
Shift the projected image position horizontally.
Move left
Shift the projected image position vertically.
Move down
Correct the keystone (trapezoid) distortion of the screen.
Magnify
H Image Shift
V Image Shift
V Keystone
Move right
Move up
Screen shrinking
at bottom
Screen shrinking
at top
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
ꢃ The default setting menu
This menu shows placement status and other settings. Items that can be set or adjusted
are marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it
indicates that you cannot select for the current input.)
Description
Item
Language
Select one of the languages below to use for displaying the menu and
messages.
[
: Enter setting mode] [
:Selection] [Apply:
]
English/Français/ㅔԧЁ᭛/ไทย/Bahasa Indonesia
Mounting
p.19
Set projection mode in accordance with Placement Style.
(Standard)
(Rear)
(Ceiling)
(Rear ceiling)
Menu Location Set the menu location on the display screen.
(Left top)
(Right top)
(Middle)
(Left bottom)
(Right bottom)
Projector ID
Signal
ID definition can be set up by menu (range 1~99), and allow user control
an individual projector by RS232.
RGB Y/Pb/Pb Video S-video HDMI
Fine Sync
Yes
No
No
No
No
Adjust with
flicker.
to eliminate
Total Dots
Yes
No
No
No
No
Adjust the number of total
dots in one horizontal period
with
H. Position
Adjust the horizontal position
of the image.
Yes
Yes
No
No
No
No
No
No
No
No
Move left
Move right
V. Position
Adjust the vertical position of
the image.
Move down
Cut off the picture and sound temporarily.
On Off
Adjust sound volume.
Quieter Louder
Move up
Mute
Volume
Advanced
Logo
Set whether the start-up screen displays when power is turned on.
On Off
Closed
Captioning
Select the closed captioning with
Off/CC1/CC2
/
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus (Continued)
ꢃ The options setting menu
Use this menu to set lamp-related and other settings.
(The items in gray color cannot be set with the current input selection.)
Description
Item
Input Search
Set whether the input source with signals is only selected or not.
On
Set whether to spin the the cooling fan speed or not.
On Off
Set whether to dispay the searching message or not.
On Off
Screen to display when there is no input signal.
Black Red Blue Green
Off
High Altitude
Information
Hide
Background
Color
White
Advanced
Power Mode
Set the power mode.
Standby Active
Direct Power On Set whether to turn on the power when the ON/STANDBY button is
pressed (On), or when the power cord is plugged in (Off).
On
Off
Auto Power Off Set the countdown timer interval. The countdown timer will start
(min)
when there is no signal being sent to the projector. The projector will
automatically power off when the countdown has finished (in minutes).
Sleep Timer
(min)
Set the countdown timer interval. The countdown timer will start
with or without a signal being sent to the projector. The projector will
automatically power off when the countdown has finished (in minutes).
Lamp Settings
Lamp Counter
(Normal)
Display the projection time of normal mode.
Lamp Counter
(ECO)
Display the projection time of ECO mode.
Lamp Life
Reminder
Set whether to display the lamp end of life warning message or not.
On
Set whether to dim the projector lamp or not.
On Off
Off
ECO Mode
Lamp Counter
Reset
Press [Yes].
Reset the lamp hour counter after replacing the lamp.
Reset
Press [Yes].
Reset all adjustments and settings to their factory settings.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
About lamp
The product’s light source is a mercury lamp that lights at increased internal pressure.
Be sure to fully understand the following characteristics of the lamp and handle it with
extreme care.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
Burst is likely to happen if the lamp is used after the replacement period has
elapsed.
When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along
with glass dust may be released from the openings for ventilation.
ꢃ Immediately replace the lamp when a replacement mes-
sage appears on the screen.
ꢀ
ꢀ
When the replacement time approaches, a message will appear on the screen.
The risk of burst will increase if the lamp is continuously used without being re-
placed.
p.34
ꢀ
Frequently check the used hours. (Refer to the Options setting menu.)
ꢃ When the lamp is broken
ꢀ
If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
In the event of lamp burst, unplug the product from the wall outlet, leave and com-
pletely ventilate the room. Then, thoroughly clean the area around the projector and
discard any edible items placed in that area, as they may be contaminated.
When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your
eyes or is inhaled.
ꢀ
ꢀ
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement
A lamp is consumable supply. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The life-
time of the lamp depends on condition of use.) If this happens, replace it with a new one.
WARNING
ꢀ
ꢀ
If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealership when the
lamp has to be exchanged.
Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger of damage from falling
pieces of glass if the lamp is broken. Besides, working at high elevations can also be hazardous. Do not attempt to
replace the lamp by yourself.
When replacing, always use lamp “PA3976U-1ET2” (sold separately). If the lamp other than the specified one is
used, it may cause a malfunction or damage to the unit due to the difference in the connector shape or the lamp rate.
CAUTION
ꢀ
ꢀ
If you have been using the projector, the lamp will be very hot, and may cause burn injuries.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
If the lamp should break, please handle with care to avoid injury due to broken pieces and contact your
dealer for repair service.
1 Unplug power cord.
2 Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
Remove the lamp cover.
1
3
4
3
4
Loosen the two screws, raise the lamp cover with
your fingers to remove the lamp cover. Use care
to avoid any damage to nails and/or tip of your
finger(s). If you have any difficulty in removal, you
can use a screwdriver or any other smaller tool for
your convenience.
2
Lamp cover
Pull up the lamp.
Loosen the two screws holding the lamp in place,
and pull up the handle to remove the lamp.
1
2
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement (Continued)
2
5
Mount the new lamp.
Align the orientation, press down the new lamp until
the bottom is reached, and lock in place using the
two lamp locking screws.
5
6
7
1
Replace the lamp cover.
Align the orientation, press down the new lamp until
the bottom is reached, and lock in place using the two
lamp locking screws.
Reset the lamp time.
See the lamp’s manual for instructions on resetting the
lamp time.
Notes and Precautions
ꢀ
The [Lamp counter (Normal) / Lamp counter (ECO)] item in the Options setting
p.34
menu indicates the time of lamp use (as a rough guide).
ꢀ
It is recommended that the lamp be replaced after 3,000 hours of normal use / 4,000
hours of eco mode. When [Lamp counter (Normal) / Lamp counter (ECO)] reaches
3,000 hours (Normal) / 4,000 hours (ECO), a message will appear. (After 3,000 hours
(Normal) / 4,000 hours (ECO), the message will appear when the power is first turned
on after each 100 hour period of use.) This display disappears when you press the
button.
ꢀ
Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
projector may fail to be powered on or the lamp may fail to come on.
Always replace the lamp with a new one.
The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
ꢀ
ꢀ
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens and main unit cleaning
WARNING
Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.
Attempting to clean or replace the lamp in a high location by yourself may cause you to fall, resulting in injury.
ꢀ
ꢀ
ꢃ Lens cleaning
ꢀ
Clean the lens with a commercially available blower and/or
lens cleaner.
ꢀ
The lens is easily scratched, so do not rub it with hard
objects, or strike it.
ꢃ Main unit cleaning
ꢀ
Unplug the power cord before cleaning the main
unit.
ꢀ
ꢀ
Wipe dirt off the main unit gently with a soft cloth.
Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or unit failure.
ꢀ
ꢀ
Do not use benzene, thinner and the like as they
may deform or discolor the unit or damage the
paint surface.
Do not use a chemically saturated cloth.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble indicators
The indicator lights to inform you of internal abnormalities.
Power LED
Message
(Blue)
(Red)
In standby state
Off
On
When connecting the power cord, the projector will
be in standby state.
In normal state
On
Off
When turning the power on (press ON/STANDBY
button), the projector will be in normal state.
Powering up
Blink
Off
Off
Off
The projector is warming up and will show the start-
(1 sec)
up logo
Power off
Blink
Cooling-I: It cannot accept any key at this status.
(0.5 sec)
Power off
Blink
(1 sec)
Cooling-II: It can accept ON/STANDBY button to
power on the projector.
Power went out during use
Blink
Problem with lamp.
Off
Off
(0.5 sec)
ꢀ
Unplug the power cord, and contact your dealer.
Power went out during use
Problem with internal cooling fan.
Blink
(1 sec)
ꢀ
Unplug the power cord, and contact your dealer.
ꢀ
After approx. 5 second of abnormal display, the
projector returns to the standby state waiting for
internal cool down.
Power went out during use
Internal overheating, or the outside temperature is
too high.
ꢀ
ꢀ
ꢀ
Place the projector so that the air intake and
exhaust are not blocked.
Unplug the power cord and wait for a short
while, then turn the power back on.
After approx. 5 second of abnormal display, the
projector returns to the standby state waiting for
internal cool down.
Blink
(0.5 sec on,
2 sec off)
Off
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling service personnel
If you think something is wrong, check the followings before contacting customer service.
p.39
Please see “Trouble indications” as well.
If This Happens
No power
Check
ꢀ
ꢀ
Is the power cord plugged in? Is it connected to the
projector?
Is the lamp cover attached properly?
p.39
Power goes out during
use
ꢀ
ꢀ
Is the ambient temperature high?
p.39
Is the air intake or air exhaust blocked?
No picture
ꢀ
Is the input source selected correctly? (When [Input
p.24
search] is [Off]).
p.27
ꢀ
ꢀ
ꢀ
ꢀ
Is the mute function on?
p.30
Is the brightness setting minimized?
p.21
Are the connections set up correctly?
Are all the connected devices functioning properly?
p.27
No audio
ꢀ
ꢀ
ꢀ
ꢀ
Is the mute function on?
Is the volume setting minimized?
p.25
p.21
Are the connections set up correctly?
Are all the connected devices functioning properly?
p.42
Picture not displayed
correctly
ꢀ
ꢀ
Is the input signal supported by the projector?
Is there something generating an abnormal video sig-
nal, for instance the video tape?
p.38
Picture blurred
Part of picture out of
focus
ꢀ
ꢀ
ꢀ
Is the lens dirty?
Is the lens focus adjusted optimally?
p.25
Is the projection distance within the projector’s supported
p.20
range?
ꢀ
Is the projector’s screen placement angle tilted too far?
p.20
ꢀ
Are the sharpness or sampling phase adjustments off?
Image is dark
ꢀ
ꢀ
Are the brightness or contrast adjustments off?
Is the lamp nearing the end of its service life?
p.30
Colors too light
Bad shading
ꢀ
ꢀ
ꢀ
Are the color, tint adjustments off?
Is the screen dirty?
p.34
Is the lamp nearing the end of its service life?
Remote control doesn’t
work
ꢀ
ꢀ
Is the remote control’s battery drained?
Is the battery inserted into the remote control correctly?
p.18
ꢀ
ꢀ
ꢀ
Is the remote control being used within the effective
range?
Are there any obstructions between the remote control
and projector?
Are there any fluorescent or other bright lights shining
at the projector’s infrared remote sensor?
p.18
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
ꢃ List of general specifications
Item
Specification
Normal mode: 255W
Standby mode: <0.5 Watt
Consumption Power
Weight
2.3 kg
External Dimensions
286 x 192 x 100 mm (W x D x H)
(including protruding parts)
Cabinet material
PC resin
Conditions for usage envi- Temp: 5ºC ~ 35ºC; relative humidity: 20% ~ 80%
ronment
Display pixels
1 DLP® chip
Picture elements
480,000 pixels (SVGA, 800H x 600V) NPS10A model
786,432 pixels (XGA, 1024H × 768V) NPX10A model
Projection system
Lens
Single Chip DLP® Technology
Zoom lens F=2.41-2.55 f=21.8-24 mm
High-pressure mercury lamp (180 W)
30 - 300 inches
Lamp
Projection screen size
Projection distance
Speaker
1.19 m - 11.89 m
2W
SERIAL terminal
COMPUTER IN terminal
Mini DIN 3 pin (Maintenance use only)
Mini D sub 15 pin Analog RGB / Y/Pb/Pr (dual use)
VIDEO terminal
S-VIDEO: Mini DIN 4 pin
VIDEO: RCA Pin Jack
AUDIO: 3.5mm dia. stereo mini-jack
HDMI: 19-pin HDMI (V1.3)
MONITOR OUT terminal
AUDIO OUT terminal
Mini D sub 15 pin RGB / Y/Pb/Pr (dual use)
3.5mm dia. stereo mini-jack
Notes
ꢀ
ꢀ
ꢀ
This model complies with the above specifications.
Designs and specifications are subject to change without notice.
This model may not be compatible with features and/or specifications that may be
added in the future.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
ꢃ List of supported signals (RGB signals)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Mode
VGA
Resolution
640x350
V-Sync [Hz]
85
H-Sync [KHz]
37.9
37.9
31.5
37.9
37.5
43.3
31.5
37.9
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60
VGA
640x400
85
VGA
640x480
60
VGA
640x480
72
VGA
640x480
75
VGA
640x480
85
VGA
720x400
70
VGA
720x400
85
SVGA
SVGA
SVGA
SVGA
SVGA
XGA
800x600
56
800x600
60
800x600
72
800x600
75
800x600
85
1024x768
1024x768
1024x768
1024x768
1280x768
1280x768
1280x720
1280x800
1152x864
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280 x 960
1400x1050
1600x1200
60
XGA
70
XGA
75
XGA
85
68.7
47.4
60.3
45
WXGA
WXGA
WXGA
WXGA
SXGA
SXGA
SXGA
SXGA
SXGA
SXGA
SXGA
SXGA
SXGA+
UXGA
60
75
60
60
49.3
53.8
63.8
67.5
77.1
63.98
79.98
91.1
60.0
65.31
75
60
70
75
85
60
75
85
60
60
60
Notes
ꢀ
Signals of which resolution exceeds the native resolution (800 x 600 pixels / 1024 ×
768 pixels) will be compressed. For this reason, some information may be lost, or im-
age quality may be affected.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
ꢃ List of supported signals (HDMI)
Mode
(1) HDMI - PC Signal
VGA
Resolution
V-Sync [Hz]
H-Sync [KHz]
640x480
640x480
60
72
31.47
37.86
37.5
VGA
VGA
640x480
75
VGA
640x480
85
43.27
35.2
SVGA
SVGA
SVGA
SVGA
SVGA
SVGA
XGA
800x600
56
800x600
60
37.88
48.08
46.88
53.67
77.2
800x600
72
800x600
75
800x600
85
800x600
119.85
60
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x960
48.36
56.48
60.02
98.8
XGA
70
XGA
75
XGA
119.804
75
SXGA
SXGA
SXGA
SXGA
SXGA
SXGA
67.5
85
77.1
60
64
75
79.98
91.15
75
85
75
(2) HDMI - Extended Wide timing
WXGA
WXGA
WXGA
WXGA
WXGA
WXGA
WXGA
WXGA
WXGA
1280x768
60
75
85
60
60
60
60
60
60
47.78
60.29
68.63
44.8
1280x768
1280x768
1280x720
1280x800
49.6
1440x900
55.9
1680x1050
1366x768
65.3
47.71
66.6
1920x1080-RB
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
Mode
Resolution
V-Sync [Hz]
H-Sync [KHz]
(3) HDMI - Video Signal
480i
480p
576i
720x480(1440x480)
720x480
59.94(29.97)
59.94
50(25)
50
27
31.47
27
720x576(1440x576)
720x576
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
31.25
45
1280x720
60
1280x720
50
37.5
33.75
33.75
67.5
56.26
27
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
60(30)
50(25)
60
50
24
23.98
26.97
ꢃ List of supported signals (Video)
NTSC
PAL
M (3.58MHz), 4.43 MHz
B, D, G, H, I, M, N
SECAM
SDTV
HDTV
B, D, G, K, K1, L
480i/p, 576i/p
720p(50/60Hz), 1080i/p(50/60Hz)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
ꢃ Pin assignment of COMPUTER IN terminal
11
15
10
Pin
No.
Pin description
During RGB input
During Y/Pb/Pr input
6
1
2
3
4
5
6
7
8
9
Video signal (R)
Video signal (G)
Video signal (B)
N.C
Color difference signal (Pr)
Luminance signal (Y)
Color difference signal (Pb)
ꢀ
GND
ꢀ
1
5
GND (R)
GND (Pr)
Mini D sub 15 Pin connector
GND (G)
GND (B)
GND (Y)
GND (Pb)
Input Signal
ꢀ
RGB input
RGB signals:
Horizontal sync signal:
Vertical sync signal:
Y/Pb/Pr input
Y signal:
+5V
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0.7V (p-p) 75 Ω
TTL level (Pos/neg polarity)
TTL level (Pos/neg polarity)
10 GND
11 N.C
12 SDA
ꢀ
13 Horizontal sync signal
14 Vertical sync signal
15 SCL
1.0V (p-p) 75 Ω
0.7V (p-p) 75 Ω
Pb/Pr signals:
ꢀ Do not connect anything.
ꢃ SERIAL terminal
Pin assignment
Pin No.
Signal Name
TXD
Description
3
1
2
3
Sending data
Receiving data
Signal ground
2
1
RXD
GND
Mini DIN 3 pin connector
Notes
ꢀ
Contact your dealer for control cable and commands.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|