TOSHIBA REMOTE RECEIPT PRINTER
TRST-A15 SERIES
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
SPAA-206-R1
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual
should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified
using the procedures described in this manual, turn off the power, unplug the machine, then contact your
authorised TOSHIBA TEC representative for assistance.
Meanings of Each Symbol
This symbol indicates warning items (including cautions).
Specific warning contents are drawn inside the symbol.
(The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items).
Specific prohibited contents are drawn inside or near the symbol.
(The symbol on the left indicates “no disassembling”.)
This symbol indicates actions which must be performed.
Specific instructions are drawn inside or near the z symbol.
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)
This indicates that there is the risk of death or serious injury if the
machines are improperly handled contrary to this indication.
WARNING
Do not use voltages other than
the voltage (AC) specified on the
rating plate, as this may cause
fire or electric shock.
Do not plug in or unplug the power
cord plug with wet hands as this
may cause electric shock.
Any other than the
specified AC voltage
is prohibited.
Prohibited
Prohibited
Prohibited
If the machines share the same
outlet with any other electrical
appliances that consume large
amounts of power, the voltage
will fluctuate widely each time
these appliances operate. Be sure
to provide an exclusive outlet for
the machine as this may cause
fire or electric shock.
Do not place metal objects or
water-filled containers such as
flower vases, flower pots or mugs,
etc. on top of the machines. If
metal objects or spilled liquid enter
the machines, this may cause fire
or electric shock.
Prohibited
Prohibited
Do not insert or drop metal,
flammable or other foreign
Do not scratch, damage or modify
the power cords. Also, do not
objects into the machines through
the ventilation slits, as this may
cause fire or electric shock.
place heavy objects on, pull on, or
excessively bend the cords, as this
may cause fire or electrical shock.
If the machines are dropped or
their cabinets damaged, first turn
off the power switches and
disconnect the power cord plugs
from the outlet, and then contact
your authorised TOSHIBA TEC
representative for assistance.
Continued use of the machine in
that condition may cause fire or
electric shock.
Continued use of the machines in
an abnormal condition such as
when the machines are producing
smoke or strange smells may cause
fire or electric shock. In these
cases, immediately turn off the
power switches and disconnect the
power cord plugs from the outlet.
Then, contact your authorised
TOSHIBA TEC representative for
assistance.
Disconnect
the plug.
Disconnect
the plug.
( i )
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Summary
SPAA-206-R1
If foreign objects (metal
When unplugging the power cords,
be sure to hold and pull on the plug
portion. Pulling on the cord portion
may cut or expose the internal wires
and cause fire or electric shock.
Disconnect
the plug.
Disconnect
fragments, water, liquids) enter
the machines, first turn off the
power switches and disconnect
the power cord plugs from the
outlet, and then contact your
authorised TOSHIBA TEC
representative for assistance.
Continued use of the machine in
that condition may cause fire or
electric shock.
the plug.
Ensure that the equipment is
properly grounded. Extension
cables should also be grounded.
Fire or electric shock could
occur on improperly grounded
equipment.
Do not remove covers, repair or
modify the machine by yourself.
You may be injured by high
voltage, very hot parts or sharp
edges inside the machine.
Connect a
No
grounding wire.
disassembling.
This indicates that there is the risk of personal Injury or damage to
objects if the machines are improperly handled contrary to this indication.
CAUTION
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
• Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification
* Shared power source
* Direct sunlight
* High humidity
* Dust/Gas
* Excessive vibration
• The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild
detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic
covers.
• USE ONLY TOSHIBA TEC SPECIFIED paper and ribbons.
• DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high
temperatures, high humidity, dust, or gas.
• Ensure the printer is operated on a level surface.
• Any data stored in the memory of the printer could be lost during a printer fault.
• Try to avoid using this equipment on the same power supply as high voltage equipment or equipment
likely to cause mains interference.
• Unplug the machine whenever you are working inside it or cleaning it.
• Keep your work environment static free.
• Do not place heavy objects on top of the machines, as these items may become unbalanced and fall
causing injury.
• Do not block the ventilation slits of the machines, as this will cause heat to build up inside the machines
and may cause fire.
• Do not lean against the machine. It may fall on you and could cause injury.
• Care must be taken not to injure yourself with the printer paper cutter.
• Unplug the machine when it is not used for a long period of time.
• Place the machine on a stable and level surface.
Request Regarding Maintenance
• Utilize our maintenance services.
After purchasing the machine, contact your authorised TOSHIBA TEC representative for assistance
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines
and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.
• Our preventive maintenance service performs the periodic checks and other work required to maintain
the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorised TOSHIBA TEC representative for assistance.
• Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or
other parts to deteriorate or cause the paint to peel.
(ii)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
TABLE OF CONTENTS
Page
1. PRODUCT OVERVIEW -----------------------------------------------------------
1.1 Introduction -----------------------------------------------------------------------------
1.2 Features ---------------------------------------------------------------------------------
1-1
1-1
1-1
2. SPECIFICATIONS -------------------------------------------------------------------
2.1 Printer ------------------------------------------------------------------------------------
2.2 Receipt Roll -----------------------------------------------------------------------------
2-1
2-1
2-2
3. APPEARANCE -----------------------------------------------------------------------
3.1 Front/Rear View -----------------------------------------------------------------------
3.2 LED and Feed Button ----------------------------------------------------------------
3.3 Connectors ------------------------------------------------------------------------------
3-1
3-1
3-1
3-3
4. SET UP PROCEDURE ------------------------------------------------------------
4.1 Requirements for Operation --------------------------------------------------------
4.2 Setting up the Printer -----------------------------------------------------------------
4-1
4-1
4-4
5. INSTALLATION PROCEDURE --------------------------------------------------
5.1 Connecting the Power Cord and Interface Cable -----------------------------
5.2 Connecting the Drawer --------------------------------------------------------------
5.3 Loading the Receipt Roll ------------------------------------------------------------
5.4 Self Test Print --------------------------------------------------------------------------
5-1
5-2
5-4
5-5
5-7
6. GENERAL MAINTENANCE -----------------------------------------------------
6.1 Cleaning ---------------------------------------------------------------------------------
6.1.1 Cleaning the Print Head and Platen ------------------------------------
6.1.2 Cleaning the Covers --------------------------------------------------------
6.2 Removing Jammed Paper ----------------------------------------------------------
6-1
6-1
6-1
6-1
6-2
7. TROUBLESHOOTING ------------------------------------------------------------
7-1
CAUTION!
1. This manual may not be copied in while or in part without prior written permission of
TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard to any queries
you may have in this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
1.1 Introduction
1. PRODUCT OVERVIEW
1. PRODUCT OVERVIEW
1.1 Introduction
Thank you for purchasing the TOSHIBA TRST-A15 Series Thermal Printer. This printer is a compact line
thermal printer designed to be connected to a TOSHIBA POS terminal or used as a kitchen printer, etc. It
prints both 80 mm-wide and 58 mm-wide receipts at the maximum print speed of 170 mm/sec. The body
color is selectable from Fair White (F) and Cool Black (C) so that it is possible to coordinate the color with
the TOSHIBA POS terminal. The interface type is either RS232C I/F or USB I/F (V2.0 Full Speed). Also
Parallel I/F is available as an option.
This manual contains general set-up and maintenance information and should be read carefully to help
gain the maximum performance and life from your printer. For most queries please refer to this manual
and keep it safe for future reference.
1.2 Features
• Due to a paper drop-in mechanism, the paper replacement can be done by just dropping a new paper
roll and closing the cover. This also makes the print head cleaning easy.
• This printer prints in thermal direct method at high speed (max. 170 mm/sec.) with less noise.
• As the paper outlet is provided in front of the printer, the receipt can be taken out easily, and flexible
installation is possible.
• Print layout can be variously arranged.
• The power supply unit (AC adapter) is detachable from the printer.
• A drawer interface (1 ch) is provided.
• An automatic cutter is provided as standard. (Partial cut)
• Two body colors are available for you to color coordinate with the TOSHIBA POS terminal to be
connected.
• User-defined characters and logos can be registered in the flash memory.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
2.1 Printer
2. SPECIFICATIONS
2. SPECIFICATIONS
2.1 Printer
Item
Printing method
Printing width
Description
Line thermal dot printing method
80 mm (576 dots)
58 mm (432 dots)
203.2 dpi x 203.2dpi
Resolution
Printing speed Max.
6.7 ips max (170 mm/sec) for 75W mode
4.0 ips max (101 mm/sec) for 55W mode
2 color printing
Max 50 mm/sec
Printing columns
80 mm Paper
48 Column (at 16.9 cpi Standard Character)
64 Column (at 22.6 cpi Compress Character)
58 mm Paper
36 Column (at 16.9 cpi Standard Character)
48 Column (at 22.6 cpi Compress Character)
Font A: 1.5 x 3.00 mm
Character size
Font B: 1.125 x 3.00 mm
Character types
Code pages PC437, PC850, PC852, PC857, PC858, PC860,
PC863, PC865, PC866 and PC1252
User defined characters and logos are downloadable in the flash
memory.
Logo registration and print
Line spacing
Printable bar codes
7.52 (default) and variable lines per inch.
UPC-A, UPC-E, JAN13 (EAN), JAN8 (EAN), Code 39, Code 128,
Interleaf 2 of 5, Codabar, PDF417, Code 93
Partial Cut
Thermal paper roll: 80 mm x dia. 83 mm (Max)
Thermal paper roll: 58 mm x dia. 83 mm (Max)
RS232C I/F or USB I/F (V2.0 Full Speed). Parallel as Option.
4K bytes/128 bytes
Cut method
Paper
Interface
Input buffer
Printer supply input voltage
Power consumption
AC adapter specification
DC 24V, 3.15A (75W)/ DC 24V, 2.29A (55W)
3.15A (75W Power Supply), 2.29A (55W Power Supply)
Rated input: AC 100 – 240V, 50/60Hz, 2.0A max
Rated output: DC 24V, 3.15A (75W)
Fair White (F) or Cool Black (C)
Body color
Operating temperature
Operating humidity
Storage temperature
Storage humidity
Weight
5ºC to 50ºC
10% to 90% RH (no condensation)
-20ºC to 60ºC
10% to 90% RH (no condensation)
2.2 Kg
Dimension
145.5 mm (W) x 221.0 mm (D) x 141.0 mm (H)
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
2. SPECIFICATIONS
2.2 Receipt Roll
2.2 Receipt Roll
HEAT SENSITIVE SURFACE
ON BOTH SIDES OF PAPER
W1 or W2
Paper type
Thermal paper rolled with the print side facing outside
Width (W1)
80 +0.5/ -1.5 mm
Width (W2)
58 +0/ -1.0 mm (With optional 58 mm paper guide)
Outer diameter (D)
Paper thickness (T)
Weight
80 +0/ -1 mm
0.062 +/- 0.005 mm
55 g/m2
Outer core diameter
Inner core diameter
Recommended thermal paper
21.5 mm
12 mm
Only paper rolled onto a core is acceptable, however, the
paper end should not be pasted to the core. TOSHIBA TEC
recommends using the following thermal paper for this
product
Manufacturer : KANZAKI
Type
: P-300
CAUTION!
Use only paper which meets specified requirements. Use of non-specified paper may shorten
the head life of the printer, resulting in problems with print quality, cause a paper feed failure or
shorten the cutter life. All paper should be handled with care to avoid any damage to the paper.
Read the following guideline carefully.
• Do not store the paper for longer than the manufacturer’s recommended shelf life.
• Store the paper in a cool, dry place. Avoid areas where they would be exposed to direct sunlight, high
temperature, high humidity, dust or gas.
• A contact of chemical or oil may discolor or erase the printed record.
• Rubbing the paper hard with nail or hard object may discolor the paper.
• The paper end should not be pasted to the core.
For further information please contact your authorized TOSHIBA TEC representative or authorized paper
manufacturer.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
3. APPEARANCE
3.1 Front/Rear View
3. APPEARANCE
3.1 Front/Rear View
Front View
Rear View
Printer Cover
LED
Top Cover
Cover Open
Button
Power Switch
Feed Button
3.2 LED and Feed Button
POWER LED (Green)
Lights when the power is turned on.
ERROR LED (Blinking Green)
The Error LED indicates an error by blinking
FEED Button
Used to feed receipt paper. A touch of this
button causes one line feed. Pressing and
holding it feeds the paper continuously. When
the power switch is turned on while the [FEED]
button is pressed and held, the printer will
perform a self test print
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
3. APPEARANCE
3. 2 LED and Feed Button
Error Status Table
Green LED Blinking (Slow)
Problem
What to Do
Where to Go
Receipt paper is low
See “Loading the
Receipt Roll” in
chapter 5.3.
There are about 4 ½ meters, ± 3 meters,
(15 feet, ± 10 feet) of paper left. Change
the paper soon to avoid running out of
paper part way through a transaction.
Green LED Blinking (Fast)
Problem
What to Do
Where to Go
Receipt paper is out
Change the paper now. Do not run a
transaction without paper as the data
may be lost.
See “Loading the
Receipt Roll” in
chapter 5.3.
Receipt cover is open
Knife failure
Close the cover. The printer will not
operate with the cover open.
Open the receipt cover and check the
knife. Clear any jammed paper you can
see. Tear off any excess paper against
the tear-off blade.
NOTE: If other LED status except for the above occurs, turn the power off, and then on. If this does not
restore the LED, contact your nearest TOSHIBA TEC representative for assistance.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
3. APPEARANCE
3. 3 Connectors
3.3 Connectors
CAUTION!
1.The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone
line or any other cables than the drawer cable to this connector. Doing so may cause a failure of
the phone line and this printer.
2.To the DC24V connector (socket connector), do not connect anything other than the built-in AC
adapter.
3.The built-in AC adapter is exclusively for this printer. Do not use it for any other machines.
1
2
3
4
1 [DC24V] (Socket connector)
The built-in AC adapter supplies +24V power to the printer through this connector. Do not connect
anything other than the TOSHIBA TEC Specified AC adapter.
2 [Serial interface connector]
An interface cable which connects the printer to a POS terminal or Personal Computer is connected to
this connector. A RS-232C interface cable (Serial I/F model) is needed for this connector.
3 [USB interface connector]
An interface cable which connects the printer to a POS terminal or Personal Computer is connected to
this connector. A USB I/F (V2.0 Full Speed) is needed for this connector.
4 [Drawer interface Connector] [CDKO] (6 pin modular connector)
A drawer cable which connects the printer to a drawer is connected to this connector. To this connector,
a TOSHIBA drawer can be connected. Do not connect anything other than the connectable drawer.
NOTE: For connectable drawers, refer to your nearest authorized TOSHIBA TEC representative.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
4. SET UP PROCEDURE
4.1 Requirements for Operation
4. SET UP PROCEDURE
4.1 Requirements for Operation
This printer has the following requirements:
Serial Interface Type
• The TOSHIBA POS terminal or Personal Computer to be connected must have a serial port.
• To communicate with the TOSHIBA POS terminal or Personal Computer, an RS-232C
interface cable is required.
RS-232C cable....... 9 pins
USB Interface Type
• The TOSHIBA POS terminal or Personal Computer to be connected must have a USB port.
• To communicate with the TOSHIBA POS terminal or Personal Computer, a USB cable is
required.
Parallel Interface Type (Option)
• The TOSHIBA POS terminal to be connected must have a Centronics parallel port.
• To communicate with the TOSHIBA POS terminal, a Centronics interface cable is required.
Centronics cable …… 36 pins.
Interface Cables
For the serial interface model, use the RS-232C cable which satisfies the following pin
configuration and the specification of the connector. For the USB interface model, use the USB
cable which satisfies the following pin configuration and the specification of the connector. For the
Parallel interface model (Option), use the Parallel cable which satisfies the following pin
configuration and the specification of the connector.
To prevent the emission and receipt of electrical noise, the interface cable must meet the following
requirements:
• Fully shielded and fitted with metal or metalized connector housings.
• Kept as short as possible.
• Should not be tightly bundled with the power cord.
• Should not be tied to power line conduits.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
4. SET UP PROCEDURE
4.1 Requirements for Operation
RS-232C cable pin configuration
TRST – A15
9 Pin Female
9 Pin Female
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
4. SET UP PROCEDURE
4.1 Requirements for Operation
USB cable connector
2
3
1
4
Printer View End
Parallel Interface Type (Option)
IEEE 1284-B receptacle
PIN No.
Signal
/STROBE
PD1-8
1
2-9
10
/ACK
11
BUSY
12
13
14
31
PERROR
SELECT
/AUTOFD
/INIT
32
36
19-30
15-18
33-35
/FAULT
/SELECTIN
GND
N.C.
N.C.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
4. SET UP PROCEDURE
4.2 Setting up the Printer
4.2 Setting up the Printer
CAUTION!
1. Place the printer on a flat, stable surface.
2. Do not place the printer close to a heater or where it may be exposed to direct sunlight.
3. Avoid locations where the printer may be exposed to high temperature, high humidity or dust.
4. Care must be taken that no condensation occurs in the printer. If it should, however,
do not turn ON the power until the condensation is dried.
5. Use a grounded electrical outlet. Do not use an adapter plug.
6. Be sure that there is adequate room around the printer for easy operation and maintenance.
7. Keep your work environment static free.
1) Make sure that the printer power is turned OFF.
2) Connect the interface cable to the printer.
3) Insert the power cord into the AC inlet.
4) Connect the interface cable to a TOSHIBA POS terminal, and plug in the power cord to the AC
outlet.
5) If a drawer is desired to be connected, connect the drawer interface cable to the printer.
6) Secure the drawer ground wire to the ground terminal on the rear of the printer.
7) Turn the printer power ON.
8) Open the printer cover.
9) Load the receipt roll into the printer.
10) Close the printer cover. One receipt will be automatically issued.
11) Check the print quality by performing a self test print.
Now the printer is ready for printing.
NOTES:
1. For details of the above Steps 1) to 4), refer to Section 5.1 Connecting the Power Cord and
Interface Cables.
2. Steps 5) and 6) are the procedures of the drawer connection. For details of Steps 5) and 6), refer to
Section 5.2 Connecting the Drawer.
3. For details of Steps 8) to 10), refer to Section 5.3 Loading the Receipt Roll.
4. For details of Step 11), refer to Section 5.4 Self Test Print.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.1 Connecting the Power Cord and Interface Cable
5. INSTALLATION PROCEDURE
WARNING!
1. Since the power cord and the interface cable are not provided with this unit, please locally
purchase ones which meet the specifications. For detail specifications, please contact your
nearest authorized TOSHIBA TEC representative.
2. Before connecting the power cord and cables to the printer, turn the power of the POS
terminal and printer OFF.
3. Do not pull the power cord hard. Doing this may damage the power cord, causing fire, electric
shock, or broken wire.
4. When it thunders, unplug the power cord. Lightning stroke may cause fire or electric shock.
5. Keep the power cord away from a heater. The cover of the power cord may be melted,
causing fire or electric shock.
6. Do not connect the power cord to the AC outlet provided on the POS terminal such as ST-
5600, ST-5500, etc.
CAUTION!
1. When separating the AC adapter, please contact your authorized TOSHIBA TEC
representative.
2. The built-in AC adapter is exclusively for this printer. Do not use it for any other machines.
3. The AC adapter can be used indoors only. Never use it outdoors.
4. Be sure to unplug the printer when it is not used for a long time.
5. Do not share the power source with other electric appliances which generate noise.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.1 Connecting the Power Cord and Interface Cable
5.1 Connecting the Power Cord and Interface Cable
CAUTION!
1. Be sure to hold the connector when plugging in or unplugging the AC adapter cable.
2. Insert the AC adapter cable and the power cord firmly.
1) Turn the printer power OFF.
2) Insert the power cord into the AC inlet.
3) Connect and secure the interface cable to the interface connector in the correct orientation.
Serial interface: Secure the connector with the screws.
USB interface: Securely insert the connector until a positive click is heard.
Parallel interface: Secure the connector with the locking tabs.
[Serial Interface Connector]
[USB Interface Connector]
[Parallel Interface Connector]
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.1 Connecting the Power Cord and Interface Cable
4) Connect the interface cable to the TOSHIBA POS terminal or Personal Computer, and then plug in
the power cord to the AC outlet.
Interface
cable
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.2 Connecting the Drawer
5.2 Connecting the Drawer
1) Turn the printer power OFF.
2) Connect the drawer cable to the drawer interface connector in the correct orientation.
[Drawer interface connector] (6-pin modular connector)
A Drawer cable which connects the printer to a drawer is connected to this connector.
To this connector, a TOSHIBA drawer can be connected. Do not connect anything other than the
connectable drawer.
NOTE: For connectable drawers, refer to your nearest authroized TOSHIBA TEC representative.
[Ground terminal] (6-pin modular connector)
The drawer interface cable’s ground wire is secured to this terminal.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.3 Loading the Receipt Roll
5.3 Loading the Receipt Roll
When you use this printer for the first time or when the receipt paper has been used up, load a receipt
roll in the following procedures while the printer power is set to ON.
A thermal printer prints thermal receipt paper by applying heat to the paper to react with the chemicals
on the paper surface. A red line which appears on the reverse side of the receipt paper indicates that
the paper is almost used up.
WARNING!
The print
head
becomes
very hot
while
printing.
Never touch
Print Head
the print
head to
avoid getting
burned.
Standard
operating
temperature
of printer is
5oC to 50oC.
Please do
not operate
out of range
for safe
Print Head
operation
Hazardous
moving
cutter. Keep
fingers and
other body
parts away
Cutter Blades
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.3 Loading the Receipt Roll
1) Turn the printer power ON.
2) Press down the Cover Open Button to unhook the printer cover. (1)
3) Check for the correct orientation of the receipt roll, and put it into the paper holder.(2)
4) Pull the receipt until it extends past the paper outlet for about 5 cm (3), and then close the printer
cover by pressing it’s front center gently and make sure that the Cover Open Button snaps up.
Cover Open Button
1
Print Cover
2
3
Receipt Roll
CAUTION!
1. Use only TOSHIBA TEC specified paper. Use of non-specified paper may shorten the print
head life resulting in problems with print quality, cause a paper feed failure, or shorten the
cutter life.
2. Do not subject the thermal receipt roll to water, oil, or heat source as this will darken the
paper.
3. Load the receipt roll in the correct orientation. Failure to do this may cause a paper jam
error.
4. Care must be taken not to damage the print head and platen when the printer cover is
opened as this may cause a poor print or a printer failure.
5. Do not open the printer cover while the printer is printing.
6. Do not hold the receipt while the printer is printing. Doing so may cause a paper jam.
7. When closing the printer cover, do not press it down too hard.
8. Do not put anything on the printer cover or push the cover too strongly. Doing so may cause
a print failure.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.4 Self Test Print
5.4 Self Test Print
To perform the printer self test, use the Mfg Adjustment menu feature. This feature prints instructions
on the receipt for selecting any type of print pattern needed.
CAUTION!
Be extremely careful when changing any of the printer settings to avoid changing other settings
that might affect the performance of the printer.
1. Set DIP switch 1 to ON, DIP switch 2 to ON.
DIP Switch
O
N
1
2
Switch 2 is shown in
the OFF position
2. Power on the printer while holding the Paper Feed Button. The printer will print the Current Setting
Form, then cuts the paper to print the Mfg Adjustment Menu.
3. If you do not hold the Paper Feed Button while power up the printer, it will go to Online Mode.
This menu allows you to print different test patterns
Selections are made using the Paper Feed Button.
===== Mfg Adjustment Menu =====
Select a sub-menu:
EXIT
> 1 Click
Rolling ASCII Print
H Print Test
Duty Check Print
Print Current Setting
EEPROM to Default
Setting
> 2 Clicks
> 3 Clicks
> 4 Clicks
> 5 Clicks
> 6 Clicks
Enter code then hold Button DOWN
at least 1 second to validate
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.4 Self Test Print
Rolling ASCII print test (Receipt)
This option let you run rolling ASCII printing test. The printer prints the resident character set in
standard pitch continuously. When Rolling ASCII Print (Rcpt) is selected, printer prints the following
menu. After selection of the printing side, test print will start.
** SELECT PRINTING SIDE?
Front Side Only
Back Side Only
Double Side
> 1 Click
> 2 Click
> 3 Click
Enter code, then hold Button DOWN at least 1 second to validate
Press the Paper Feed Button to stop the test.
Rolling ASCII
Stop and exit test
> Long Click
Page number
00000008
!”#$%&
!”#$%&’
“#$%&’(
O
P
Q
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
H print test (Receipt)
5.4 Self Test Print
This option let you run H printing test. The printer prints the ‘H’ character in standard pitch
continuously. When H Print Test (Rcpt) is selected, printer prints the following menu. After selection
of the printing side, test print will start. Press the Paper Feed Button to start or stop the test.
** SELECT PRINTING SIDE?
Front Side Only
Back Side Only
Double Side
> 1 Click
> 2 Click
> 3 Click
Enter code, then hold Button DOWN at least 1 second to validate.
Press the Paper Feed Button to stop the test.
H Print test
Stop and exit test
-> Long Click
Page number
00000008
HHHHH
HHHHH
HHHHH
H
H
H
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
Duty check print test (Receipt)
5.4 Self Test Print
This option let you run duty check printing test. The printer prints the 12.5%, 25%, 50% and 100% duty
original pattern. When Duty Check Print (Rcpt) is selected, printer prints the following menu. After
selection of the printing side, test print will start.
Press the Paper Feed Button to start or stop the test.
** SELECT PRINTING SIDE?
Front Side Only
Back Side Only
> 1 Click
> 2 Click
Double Side
> 3 Click
Enter code, then hold Button DOWN at least 1 second to validate.
Press the Paper Feed Button to continue or stop the test.
Duty Check Print
Stop and exit test Short Click
Continue test
Long Click
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
5. INSTALLATION PROCEDURE
5.4 Self Test Print
Print current setting
This option let you print current setting on receipt.
Press the Paper Feed Button to start the test.
** START CURRENT SETTING PRINTING?
Return Main Menu
Start Printing
> Short Click
> Long Click
NOTE: Press the Paper Feed Button for at least one second to validate the selection.
*** Current Setting Form ***
Model number
Serial number
: TRST-A15
: 12345678901
Boot Firmware
Version
Revision
CRC
: V00.02
: 00
: DEEB
Flash Firmware
Version
Revision
CRC
: V00.06
: 00
: 6696
SBCS
Version
Revision
: V00.01
: 00
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
6.1 Cleaning
6. GENERAL MAINTENANCE
6. GENERAL MAINTENANCE
WARNING!
1. Be sure to disconnect the power cord prior to performing any maintenance.
2. DO NOT POUR WATER directly onto the printer, as this may cause electric shock or fire.
3. The print head becomes very hot while printing. To avoid getting burned, never touch the
print head during the maintenance.
CAUTION!
1. Do not use any sharp object to clean the print head and platen. Doing so may damage
them, causing poor print or missing dots.
2. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents
may discolor the covers.
3. Do not touch the print head element as static built-up may damage the print head
To help retain the high quality and performance of your printer it should be cleaned regularly. The
greater the usage on the printer, the more frequent the cleaning. (i.e. low usage=weekly, high
usage=daily)
Platen
Print Head Element
6.1 Cleaning
6.1.1 Cleaning the Print Head and
Platen
1) Turn the power OFF and open the printer
cover.
2) Clean the print head element (cross
hatched area in the figure on the right)
with a cotton swab slightly moistened
with alcohol.
3) Clean the platen with a soft cloth
moistened with alcohol.
CAUTION!
Hot surface. (Please refer to the
WARNING! On the above)
6.1.2 Cleaning the Covers
Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After using
detergent for cleaning, be sure to wipe it off with a slightly moistened cloth.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
6. GENERAL MAINTENANCE
6.2 Removing Jammed Paper
6.2 Removing Jammed Paper
1) Turn the power OFF.
2) Open the printer cover.
3) Remove the jammed paper. DO NOT USE any sharp implement or tool as these will damage
the printer.
4) Clean the print head and platen, then remove any further dust or foreign objects.
5) Re-load the receipt roll. (Refer to Section 5.3 Loading the Receipt Roll.)
6) After closing the printer cover, turn the power ON. The printer will initialize the auto cutter to restore
the printer stand-by.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPAA-206-R1
7. TROUBLESHOOTING
7. Troubleshooting
7. TROUBLESHOOTING
WARNING!
If you cannot solve a problem with the following solutions, do not attempt to repair it by
yourself.
Turn the power off, unplug the printer, then contact your authorized TOSHIBA TEC
representative for assistance.
Problem
The power is not turned
on. (Power LED does
not light.)
Check Point
Solution
Plug it in correctly.
•
•
Is the power cord
plugged in correctly?
Is power supplied to the
AC outlet?
•
•
If it is not a power
failure, check if the
power is supplied to the
AC outlet with another
electric appliance. If not,
contact your nearest
power company.
•
Check the circuit
breaker.
•
Has the circuit breaker
tripped?
Receipt paper is not
issued.
•
•
Refer to Section 5.3
and load the receipt roll
properly.
Refer to Section 6.2
and remove the jammed
paper, and re-load the
receipt roll.
•
•
Is the receipt roll loaded
properly?
Does a paper jam error
occur?
No printing is performed
though the POWER LED
lights.
•
•
Is the interface cable
connected correctly?
Does the specification
of the interface cable
meet that of the POS
terminal or the printer?
•
•
Connect the interface
cable correctly.
Use a TOSHIBA TEC-
recommended interface
cable or an interface
cable which meets the
specification of the
printer.
Issued receipt paper is
stained.
•
Is the print head dirty?
•
Refer to Section 6.1
and clean the print
head.
Irregular print/blurred
print
•
•
Is the proper paper
used?
•
•
Refer to Section 2.2
and use the TOSHIBA
TEC specified paper.
Do not use dampened
paper
Is the paper
dampened?
NOTE: If any problem occurs other than the above, please contact your authorized TOSHIBA TEC
representative.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Waste Recycling information for users:
Following information is only for EU-member states:
The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste.
By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for
the environment and human health, which could otherwise be caused by incorrect waste handling of this product.
For more detailed information about the take-back and recycling of this equipment, please contact the supplier that
provided you with the product in question.
French
Information aux utilisateurs concernant le recyclage des déchets:
Les informations suivantes sont uniquement destinées aux pays membres de l’Union Européenne:
L’utilisation du symbole de "poubelle à roulettes barrée" indique que ce produit ne doit pas être traité comme un déchet
ménager classique.
En vous assurant que ce produit est correctement mis au rebut, vous participerez à la prévention de l’environnement et
de la santé publique, contre des conséquences négatives potentielles qui pourraient résulter d’un traitement inapproprié
des déchets de ce produit. Pour obtenir des informations complémentaires concernant la récupération et le recyclage de
ce produit, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit.
German
Wiederverwertungsinformationen für Verbraucher:
Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten:
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner Haushaltsmüll
behandelt werden darf.
Indem Sie aktiv mitwirken, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit, mögliche negative
Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden, die sonst durch die unsachgemäße
Entsorgung dieses Produktes beeinträchtigt werden könnten.
Für nährere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden sie sich bitte an den
Lieferanten, von dem Sie dieses Produkt erworben haben.
Spanish
Información para usuarios sobre el reciclaje de residuos:
La siguiente información sólo concierne a los Estados Miembros de la UE:
El uso del símbolo de un contenedor con ruedas tachado indica que este producto no puede ser tratado como si fuera
un residuo doméstico.
Asegurando que nos deshacemos de este producto de forma correcta, ayudaremos a evitar potenciales consecuencias
negativas tanto para el medio ambiente como para la salud pública, que podrían producirse debido a un tratamiento
inapropiado de este producto. Para obtener una información más detallada sobre la recogida y reciclaje de su producto,
por favor, póngase en contacto con el proveedor donde lo compró.
Dutch
Gebruikersinformatie over het recycleren van afval:
De volgende informatie geldt enkel in EU-lidstaten:
Het symbool met de doorkruiste afvalbak geeft aan dat dit product niet mag worden behandeld als algemeen
huishoudelijk af val.
Door dit product op de juiste manier van de hand te doen beschermt u het milieu en de volksgezondheid tegen mogelijke
negatieve gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de resten van dit product.
Voor gedetailleerde informatie over het terugnemen en recycleren van dit product, gelieve contact op te nemen met de
leverancier van dit product.
Italian
Informazioni sul riciclo del prodotto:
Le seguenti informazioni riguardano gli stati membri EU:
Il simbolo con il bidone sbarrato indica il non poter smaltire questo prodotto come rifiuto domestico.
L'accertamento che questo prodotto sia smaltito correttamente contribuirà ad impedire le potenziali conseguenze
negative per l'ambiente e la salute umana che potrebbero essere causati, al contrario, dall'errato smaltimento dello
stesso. Per informazioni più dettagliate sulle modalita di resa e riciclaggio di questo prodotto mettetevi in contatto con il
fornitore da cui l'avete aquistato.
Portuguese
Informação sobre reciclagem:
A informação que se segue é apenas dirigida a países membros da CEE:
A utilização deste símbolo indica que este produto não pode ser tratado como lixo comum.
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais consequências negativas
para o ambiente e para a saúde humana, que poderiam ser causadas pelo inapropriado tratamento deste produto.
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED IN SINGAPORE
SPAA-206-R1
TSMB0039801
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Texas Instruments Stereo Amplifier TAS5727 User Manual
Think Outside Mouse 101797E User Manual
Toshiba Security Camera IK TF7H User Manual
Tote Vision Computer Monitor LCD 1048HDM User Manual
Uniden Telephone EXS 2010 User Manual
Univex Portable Speaker iHM6 IB User Manual
VBrick Systems Switch Version 200 User Manual
Verilux Indoor Furnishings PL04 User Manual
Viking Double Oven VDSC560 6GQSS User Manual
Vinotemp Refrigerator VT 32BSW User Manual