Toshiba Network Hardware GA 1170 User Manual

NETWORK EXPANSION KIT  
GA-1170  
File No. SME04003700  
R04122173800-TTEC  
Ver00_2005-02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
General Precautions for Installation/Servicing/Maintenance for the GA-1170  
The installation and service should be done by a qualified service technician.  
1. When installing the GA-1170 to the Equipment, be sure to follow the instructions  
described in the "Unpacking/Set-Up Procedure for the GA-1170" booklet which comes  
with each unit of the GA-1170.  
2. The GA-1170 should be installed by an authorized/qualified person.  
3. Before starting installation, servicing or maintenance work, be sure to turn OFF and  
unplug the equipment first.  
4. When servicing or maintaining the GA-1170, be careful about the rotating or operation  
sections such as gears, pulleys, sprockets, cams, belts, etc.  
5. When parts are disassembled, reassembly is basically the reverse of disassembly  
unless otherwise noted in this manual or other related materials. Be careful not to  
reassemble small parts such as screws, washers, pins, E-rings, toothed washers to the  
wrong places.  
6. Basically, the machine should not be operated with any parts removed or disassembled.  
7. Delicate parts for preventing safety hazard problems (such as switches, sensors, etc. if  
any) should be handled/installed/adjusted correctly.  
8. Use suitable measuring instruments and tools.  
9. During servicing or maintenance work, be sure to check the serial No. plate and other  
cautionary labels (if any) to see if they are clean and firmly fixed. If not, take appropriate  
actions.  
10. The PC board must be stored in an anti-electrostatic bag and handled carefully using a  
wristband, because the ICs on it may be damaged due to static electricity. Before using  
the wrist band, pull out the power cord plug of the equipment and make sure that there  
is no uninsulated charged objects in the vicinity.  
11. For the recovery and disposal of used GA-1170, consumable parts and packing  
materials, it is recommended that the relevant local regulations/rules should be  
followed.  
12. After completing installation, servicing and maintenance of the GA-1170, return the  
GA-1170 to its original state, and check operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
[ 1 ] CONFIGURATION ................................................................................ 1 - 1  
[ 2 ] SPECIFICATIONS................................................................................. 1 - 1  
[ 3 ] UNPACKING AND INSTALLATION....................................................... 3 - 1  
[ 4 ] SETUP IN A WINDOWS ENVIRONMENT............................................ 4 - 1  
[ 5 ] UPDATING NETWORK BOX FIRMWARE............................................ 5 - 1  
[ 6 ] TROUBLE CODE .................................................................................. 6 - 1  
[ 7 ] CIRCUIT DIAGRAM .............................................................................. 7 - 1  
[ 8 ] PWB PARTS LAYOUT .......................................................................... 8 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[ 1 ] CONFIGURATION  
e-STUDIO162/162D  
e-STUDIO151/151D  
GA-1170  
[ 2 ] SPECIFICATIONS  
1. BASIC SPECIFICATIONS  
ITEMS  
Accessories  
SPEC  
ITEMS  
SPEC  
e-STUDIO162/162D  
e-STUDIO151/151D  
USB cord x 1  
Extensible model  
(for connection to Copier)  
Software CD-ROM x 3  
Screw for installation x1  
Standard memory  
Expansion memory  
64MB  
DIMM 1slot  
144pin 128/256MB SO-DIMM  
Clamp x 1  
(for harness fixation)  
Installation manual  
Installation guide  
Platform of Client PC  
Useable OS  
IBM PC/AT compatible, Macintosh  
Windows98/Me/NT4.0/2000  
professional/Windows XP Home  
Edition/Professional Edition  
*An installation manual exists in  
driver CD-ROM by the pdf file for-  
mat.  
Mac OS 8.6-9.x,10.1.5,10.2-10.2.8(w/  
o 10.2.2)(PS option)  
Bundle software  
Disk1:Driver CD-ROM  
for e-STUDIO162/162D,  
e-STUDIO151/151D  
PCL driver (Win)  
PS driver (Win/Mac)  
SMON (Win)  
PAU (Win)  
NIC Manager (Win)  
Online manual (Win/Mac)  
Required hardware(PC)  
(System)  
The conditions of each OS which can  
be used are required.  
(HDD)  
Exceeding 100M is recommended.  
(Monitor)  
800 x 600 dots  
(Interface)  
10BASE-T/100BASE-TX Ethernet  
Disk2:Network setting CD-ROM  
NIC Manager (Win)  
Quick Setup (Win)  
SC-Print2000 (Win)  
Online manual (Win/Mac)  
Setup Utility (Mac)  
Required software  
Internet Explorer 5.5 or later  
Netscape Navigator 6 or later  
Extensible option  
Network Protocol  
PS extensible kit (GA-1180)  
TCP/IP, IPX/SPX, NetBEUI, Ether  
Talk  
Disk3:Application CD-ROM  
Desktop Document Manager  
(3 license)  
Emulation (The functions PCL/PS (PS:Cancels by the soft key)  
which can be used differ by  
The MFP connected)  
Network Print  
PCL/PS  
Network Scan (The functions Scan to E-mail, Scan to FTP,  
which can be used differ by Scan to Desktop  
The MFP connected)  
E-mail alert status  
Power supply  
Yes (Cancels by the soft key)  
Supplies via copier  
(AC power supply built-in) AC120mA  
Power consumption  
5.5W  
Outside dimension  
(W x D x H)  
248mm x 127mm x 59mm  
GA-1170 CONFIGURATION  
1 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. FUNCTION DESCRIPTION  
A. PRINT EMULATION  
A difference exists in the function which can be used by execution of the basic performance and composition of the MFP to connect (print size/config-  
uration).  
(1) comparison table of main print function classified by driver  
PCL6 (XL)/  
SPDL2  
Custom Driver  
PCL5e  
Custom Driver  
PS  
Macintosh  
PPD file  
Windows  
PPD file  
Function  
Document  
Custom Driver  
General  
1-Sided, 2-Sided(Book) 2-Sided(Tablet), Pamphlet Style(Tiled Pam-  
phlet), Pamphlet Style(2-up Pamphlet)  
1-Sided, 2-Sided(Book), 2-Sided(Tablet)  
No  
Style  
Booklet  
Binding Edge  
N-up  
Yes  
No  
Win 9x : 2/4  
Win2K/XP: 2/4/6/8/16  
2/4/6/8/16  
N-up Order  
Z
Z, Reverse Z, N, Reverse N  
1size  
Z
Custom  
Paper Size  
3 sizes  
Different 1st  
(Cover)  
Yes  
No  
Graphic  
Resolution  
Setting  
600/300 dpi  
No  
600dpi  
Half tone  
Setting  
Yes  
No  
Graphics  
Mode  
Raster/HP-GL2  
Raster/Vector  
No  
Negative  
Image  
No  
No  
Yes  
Mirror Image  
Fit to Page  
Yes  
X
Yes  
Yes  
Font  
Resident  
Font  
136 fonts,  
5 Kanji fonts  
(Japan only)  
35 fonts,  
5 Kanji fonts  
(Japan only)  
136 fonts,  
5 Kanji fonts  
(Japan only)  
80 fonts  
Download font  
No  
Yes  
Others  
Configura-  
tion Setting  
Yes (Automatic)  
No  
Job  
Compression  
No  
No  
Yes  
Yes  
No  
No  
Bitmap  
Compression  
(2) comparison table of printing function for each driver  
The model to connect  
e-STUDIO162/162D, e-STUDIO151/151D  
Function  
General Copies  
Orientation  
PCL5e  
PCL6  
PS  
Mac PPD  
Win PPD  
1-999  
Portrait/Landscape  
Collate/Group  
Collate  
Document Style  
1-Sided, 2-Sided(Book), 2-Sided(Tablet),  
Pamphlet Style(Tiled Pamphlet), Pamphlet Style(2-up Pamphlet)  
1-Sided, 2-Sided(Book), 2-Sided(Tablet)  
No  
Booklet  
(e-STUDIO162/162D, e-STUDIO151/151D)  
Invoice on Letter, A5 on A4, Letter on Letter, A4 on A4  
Binding Edge  
Margin Shift  
N-up  
No  
No  
2/4/6/8/16  
Win9x: 2/4  
Win2k/XP: 2/4/6/8/16  
*2  
N-up order  
Z
Z, Reverse Z, N, Reverse N  
Z
GA-1170 SPECIFICATIONS  
1 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The model to connect  
Function  
e-STUDIO162/162D, e-STUDIO151/151D  
PS Mac PPD  
PCL5e  
PCL6  
Win PPD  
On/Off *2  
General N-up Border  
On/Off  
Yes  
(Single hairline/Sin-  
gle thin line/Double  
hairline/Double thin  
line)  
Paper  
Paper Size  
(e-STUDIO162/162D, e-STUDIO151/151D)  
A3/B4/A4/B5/A5/B6/A6/11x17/8.5x14/8.5x13/8.5x11/5.5x8.5/Folio/Executive/COM-10/Monarch/DL/C5/8K/16K  
Fit to Page size  
(e-STUDIO162/162D, e-STUDIO151/151D)  
A4/B5/A5/B6/A6/8.5x14/8.5x13/8.5x11/5.5x8.5/Folio/Executive/COM-10/Monarch/DL/C5/8K/16K  
Paper Type  
No  
Custom Paper  
Size  
1 size  
1size *1  
3 sizes *2  
Source Selection  
Auto/Bypass (Auto)  
e-STUDIO162/162D, e-STUDIO151/151D: Tray 1/2  
On/Off  
Different 1st  
(cover)  
No  
Transparency  
Inserts  
No  
Carbon Copy  
No  
No  
Paper  
Output  
Output Tray  
Selection  
Staple  
No  
Graphic Resolution Setting  
Half tone Setting  
600/300 dpi  
No  
600 dpi  
Screen Frequency 8 to  
360.0 in 0.1 steps  
No  
Screen angle 0.0 to  
360.0 in 0.1 steps  
Graphics Mode  
Raster  
HP-GL2  
Raster  
Vector  
No  
Smoothing  
No  
Toner save  
No  
Half tone Enhance  
No  
Graphic  
Brightness  
No  
Negative Image  
Mirror Image  
Zoom  
No  
No  
On/Off  
Horizontal/Vertical  
No  
25-400%  
No  
Fit to Page  
On/Off  
Font  
Resident Font  
Download Font  
80 fonts  
136 fonts  
35 fonts  
No  
136 fonts  
Bitmap, TrueType, Graphics  
Type1  
True Type  
Others  
Configuration Set-  
ting  
Yes (Automatic)  
No  
ROPM  
On/Off  
Overlay  
On/Off  
On/Off  
No  
Print Auditor  
Job Retention  
Watermark  
No  
No  
On/Off(With functional restriction)  
Page Protection  
Job Compression  
No  
None, Fastest, Fast,  
Medium, Best  
No  
No  
No  
No  
None, Very High, High,  
Medium, Draft  
Job Compression  
*1:Mac OS 10.1 is not supported.  
*2:Windows NT is not supported.  
GA-1170 SPECIFICATIONS  
1 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(3) PDF/TIFF direct printing function  
B. NETWORK SCANNING FUNCTION  
PDF and TIFF files can be specified from a web page and directly  
printed out.  
It is possible to use the MFP scanning function as a network scanner  
with a network scanner expansion kit. Setups can be made using a  
Web browser. Supported functions vary with the type of the MFP con-  
nected.  
(4) Limitations (printing function)  
If a print request for GDI/SPLC data is made, an error message is  
printed out.  
(1) Basic scanning function  
(5) Printer condition setup  
e-STUDIO162/162D,  
e-STUDIO151/151D  
Function  
Item  
Remarks  
The following setup can be made from the web page.  
Network Scan to E-mail  
scanner  
Yes  
Yes  
Default Setting Items  
Scan to Desk-  
Item  
top  
Function  
Default  
e-STUDIO162/162D,  
e-STUDIO151/151D  
Scan to FTP  
server  
Yes  
Yes  
Copies  
1-999  
1
Destina- Specify e-mail  
tion  
address with  
LDAP  
Orientation  
Portrait / Landscape  
Portrait  
Default Paper Size  
(Overseas)  
Invoice  
Letter  
Foolscap  
Legal  
Letter or A4  
AdHoc  
Yes  
Yes  
(Enter e-mail  
address from  
MFP.)  
(Domestic)  
A5 B5 A4  
(China - size of AB sys-  
tem)  
A5 B5 A4  
16K  
JPEG  
TIFF/PDF multi-  
ple page support  
File  
format  
PDF  
(non-compres-  
sion, G3, G4)  
TIFF  
(non-compres-  
sion,G4, G4)  
Default Paper Source  
drop down box select  
values:  
AUTO  
(2) Scanner settings  
AUTO Tray1  
Tray2  
BYPASS  
Item  
Default  
Setting  
Remarks  
e-STUDIO162/162D, e-STUDIO162/162D,  
e-STUDIO151/151D  
e-STUDIO151/151D  
Disable Blank Page Print Enable/Disable  
Disable  
Scan-  
ning size  
A4 (AB region)  
Letter (Inch-sys-  
tem region)  
*When destination lan-  
guage is Japanese.  
2-Sided Print  
drop down box slect  
values:  
1-SIDED  
2-SIDED (BOOK)  
2-SIDED (TABLET)  
1-SIDED  
File  
format  
JPEG color/JPEG TIFF monochrome,  
gray scale/PDF  
color/PDF gray  
scale/PDF mono-  
chrome,  
binary G4 com-  
pression  
binary non-com-  
pression/PDF  
monochrome,  
binary G3 com-  
pression/PDF  
monochrome,  
binary G4 com-  
pression/TIFF  
color/TIFF gray  
scale/TIFF mono-  
chrome,  
binary non-com-  
pression/TIFF  
monochrome,  
binary G3 com-  
pression/TIFF  
monochrome,  
binary G4 com-  
pression  
ROPM  
Enable / Disable  
Disable  
(6) Network status page  
The network status pages shows a list of settings about the network.  
Data are printed out in the A4 or letter size in US English regardless of  
the destination and OS language selected.  
The status page can be printed out by pressing the status switch on the  
network expansion kit.  
Note:  
1. The name of the printer is printed under the item "printer name."  
2. When WINS is disabled, "WINS server 1-5" is not displayed. It is  
displayed when a value is set or information is acquired from the  
DHCP server.  
Color  
mode  
Monochrome,  
2 gradations/Gray 2 gradations  
scale/Full color  
Monochrome,  
Available only at  
the mono-  
chrome.  
Any server which responds normally to the registration of WINS is  
marked with an asterisk "".  
Resolu- 75/100/150/200/  
75  
Selectable reso-  
lutions vary with  
different mem-  
ory capacities.  
"WINS server" shows up to 5 values: 2 settings, 2 DHCP values,  
and broadcast. However, the broadcast operates only when no nor-  
mal response is returned from any server.  
tion  
300/400/600  
3. The "WINS Scope ID" is displayed only when a value is set or when  
information is acquired from the DHCP server and more than one  
piece of information is valid as a WINS server.  
B/W  
thresh-  
old  
1-254  
(default: 128)  
128  
GA-1170 SPECIFICATIONS  
1 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(4) Recipient registration  
Item  
Default  
[e-STUDIO162/162D, e-STUDIO151/151D]  
Setting  
Remarks  
e-STUDIO162/162D, e-STUDIO162/162D,  
e-STUDIO151/151D e-STUDIO151/151D  
Up to 200 destinations can be registered on the network expansion  
Light  
source  
Red/  
Green/  
Blue  
White/  
Red/  
Green/  
Blue  
Green  
White  
Light source can  
be selected only  
when the color  
mode is in  
kit to which the scan can be sent from the network scanner.  
The mail address registered for each destination can be selected  
from the mail address which is searched using LDAP.  
"Monochrome".  
The information for each recipient includes the recipient name, IP  
address or mail address, scanning size, format type, and scan  
parameter.  
Void  
On/Off  
On  
When On is  
selected, the  
edges of images  
are cut.  
Either of LDAP-selected or directly-entered mail address scan setting  
is available. If the destination is a mail address entered through the  
main system or selected by LDAP, this scan setting is used.  
(3) Send file (message and filename)  
Information contained in filename  
The destination name is displayed on the LCD.  
Sender name  
Date & Time  
: Use MFP product name.  
: Date and time at which file is sent  
Image send counter  
(5) Scanning size  
[e-STUDIO162/162D, e-STUDIO151/151D]  
Session page  
counter  
:
Scanning size is the size set up in main unit(Copier).  
(Apply to the main scan, a subscan, ADF, and OC)  
Unique identifier  
: Automatically created based on the information  
of the date and time and image send counter.  
(6) Scanner limitations  
[e-STUDIO162/162D, e-STUDIO151/151D]  
Example:  
e-STUDIO162D_20000620_155114_0057_06a3f3393948.pdf  
The scanning function is allocated to the network expansion kit. The b  
Button Manager settings are disabled.  
Mail subject  
When the network expansion kit is connected, the scanner function  
through TWAIN (pull scan) and push scan which used button man-  
ager on pc are not available.  
Can be freely set.  
Default: Scanned image. device name: e-STUDIOXXX (MFP product  
name)  
Example: Scanned image. device name: e-STUDIO162D  
Mail message  
The following messages are added to the image send mail.  
Device name:  
Model:  
Freely set  
MFP product name  
Freely set  
Location:  
File type:  
Resolution:  
File type of send image  
Resolution of send image  
Example;  
Device name:e-STUDIO162D  
Model name :e-STUDIO162D  
Location  
File type  
:D2) Planning dept.  
:PDF MMR (G4)  
Resolution :200 dpi x 200 dpi  
GA-1170 SPECIFICATIONS  
1 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. FUNCTIONS BY INTERFACE  
F. HARDWARE SETUP  
Supplied by the main unit  
When the network expansion kit is connected, the following functions  
are available by system interface.  
[e-STUDIO162/162D, e-STUDIO151/151D]  
1) Connection to the system unit  
Connect to the USB2.0 port  
2) Power supply  
Function  
System I/F  
(main unit)  
GA-1170 I/F  
SPLC GDI PCL5e/6 PS (*1) Net  
Scan  
USB2.0  
RJ45 (LAN)  
No  
Yes  
Yes  
Yes  
No  
No  
No  
No  
No  
No  
No  
No  
Yes  
Yes  
No  
No  
No  
Yes  
No  
No  
No  
Yes  
No  
No  
No  
Supplied by the main unit.  
USB1.1  
IEEE1284  
USB2.0  
USB1.1  
RJ45 (LAN)  
Yes (*2) Yes (*2) No  
No No No  
Yes (*2) Yes (*2) No  
No No No  
IEEE1284  
USB1.1  
Yes  
No  
RJ45 (LAN)  
IEEE1284  
No  
(*1): PS requires soft keys of the GA-1180.  
(*2): Some functions are not available.  
D. NETWORK SETUP  
Network setups should be performed by the system administrator. Use  
a setup tool such as TCP/IP, Netware, Ether Talk or Web interface.  
E. SOFTWARE SETUP  
The network expansion kit can be installed by setting up NIC, installing  
a printer driver with the total installer, and installing Desktop Document  
Manager.  
(1) Installing driver  
The network expansion kit printer is connected only through the net-  
work. The port setup required for installing a printer driver is the network  
only. The following items should be set up.  
TCP/IP peer-to-peer port  
1) Search for the network expansion kit on the network and select the  
network expansion kit you want or enter the IP address of the appli-  
cable network expansion kit to create a TCP/IP port.  
2) Install the driver to the created port.  
Windows printer shared port  
When the setup of the above client PC is completed and the printer is  
set to "Windows shared printer," other client PCs can select this  
printer shared port and then proceed to installation of the driver.  
GA-1170 SPECIFICATIONS  
1 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[ 3 ] UNPACKING AND INSTALLATION  
The unpacking and set-up procedure shall be done by a qualified  
service technician.  
1. UNPACKING  
3. INSTALLATION PROCEDURE  
This installation procedure is provided for e-STUDIO162/162D,  
e-STUDIO151/151D.  
For Installation to other models, see the operation manual of the main  
unit or the service manual.  
Turn off the main switch of the main unit and remove the power  
plug of the copier from the outlet.  
1. Cut the rear cabinet.  
1) Remove the ADF/ RADF from the main unit and gently place it on  
the document glass as shown in the illustration.  
2) Cut out two cut-out portions from the rear cabinet using a cutter or  
the like.  
3) Use a Phillips screwdriver or the like to open a hole.  
4) Remove the screw and then remove the rear cabinet cover.  
5) Cut out a part of the rear cabinet cover with nippers or the like as  
shown in illustration.  
(Be careful about the orientation of the nippers so that the cross  
section is flat.)  
2. PACKAGED GOODS  
Parts included  
CD-ROM ... 3 pcs.  
Network  
expansion kit  
Screw (3 x 14) ... 1 pc.  
2. Attach the network expansion kit.  
1) Engage the two pawls on the rear of the network expansion kit with  
the cutout portions of the main unit and secure the kit with the sup-  
plied screw (3 x 14).  
Important  
information ... 1 sheet  
USB cable ... 1 pc.  
Clamp ... 1 pc.  
2) Connect the connector of the network expansion kit to the connec-  
tor of the main unit.  
3) Secure the rear cabinet cover to the main unit with the screw.  
4) Attach the ADF/ RADF to the main unit.  
GA-1170 UNPACKING AND INSTALLATION  
3 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Connect the USB cable and the network cable.  
1) Attach the supplied cable clamp to the position shown in the illustra-  
tion.  
2) Connect the USB cable to the network expansion kit and the main  
unit.  
At this time, reduce slack of the cable with the cable clamp as  
shown in the illustration.  
3) Connect the network cable.  
Insert the power plug of the copier to the outlet, turn the main  
switch of the copier to the “ON” position, and then perform net-  
work setting and installation of the software.  
GA-1170 UNPACKING AND INSTALLATION  
3 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[ 4 ] SETUP IN A WINDOWS ENVIRONMENT  
8) Click the "NICManager" button.  
1. SETTING THE IP ADDRESS OF THE  
MACHINE  
Before installing the printer driver, be sure to set the IP address of the  
machine. Consult your network administrator for the correct IP address,  
subnet mask, and default gateway to be entered. If a DHCP server will  
automatically assign an IP address to the machine, the following proce-  
dure is not necessary. (To check the IP address assigned to the  
machine by DHCP, see "2. CHECKING THE IP ADDRESS" .)  
Note: If the machine is used in a DHCP environment, the machine's IP  
address may change automatically. If this happens, printing will  
no longer be possible. In this event, use a WINS server or do not  
use the machine in a DHCP environment.  
1) Make sure that the LAN cable is connected to the machine and then  
turn on the machine.  
2) Insert the network expansion kit GA-1170 "Software" CD-ROM into  
your computer's CD-ROM drive.  
3) Click the "start" button, click "My Computer" (  
click the CD-ROM icon ( ).  
), and then double-  
9) The printer or printers connected to the network will be detected.  
Click the printer to be configured (the machine).  
In Windows 95/98/Me/NT 4.0/2000, double-click "My Computer"  
and then double-click the CD-ROM icon.  
Select the "GA-1170".  
4) Double-click the "setup" icon (  
).  
Note: If the language selection screen appears after you double click  
the "setup" icon, select the language that you wish to use and  
click the "Next" button. (Normally the correct language is  
selected automatically.)  
5) The "SOFTWARE LICENSE" window will appear. Make sure that  
you understand the contents of the license agreement, and then  
click the "Yes" button.  
6) Read the message in the "Welcome" window and then click the  
"Next" button.  
10) Click the "Print Server Card Setup" button.  
7) Click the "Administrator Tools" button.  
Enter your password in the password entry screen and click "OK".  
The Print Server Card Setup window will appear.  
The password for this product has been initially set to "TOSHIBA".  
If the "Guest user" checkbox is selected, the settings can be  
viewed but not configured.  
11) Click the "TCP/IP" tab.  
GA-1170 SETUP IN A WINDOWS ENVIRONMENT  
4 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12) Configure the settings and then click the "Update" button.  
3. PRODUCT KEY SETTING  
To enable the PS3 function and the e-mail status & alerts function,  
follow the procedures below. In addition, to enable the PS3 function,  
you need GA-1180 (option).  
1) Make sure that the LAN cable is connected to the machine and then  
turn on the machine.  
2) Enter the IP address in web browser to open the web page.  
3) Select "Product Key Setting" in "Device Setup" from MENU.  
Be sure to ask your network administrator for the correct IP  
address, subnet mask, and default gateway to be entered.  
13) Your changes to the settings appear.  
Make sure that the changes are correct and then click the "OK"  
button.  
14) Restart the machine.  
4) Set "User name" to "admin" and "Password" to "TOSHIBA" in the  
screen displayed.  
Power off the machine and then power it back on.  
15) Select "Search" from the "File" menu.  
5) Click the "OK" button to obtain the "Product Number".  
The IP address that you entered will appear. Make sure that it is  
correct.  
The completes the IP address settings.  
2. CHECKING THE IP ADDRESS  
To check the IP address of the machine, press the status button on the  
network expansion kit to print out a network status page.  
6) Fill in the product number in the following column of the product  
sheet (MACHINE SERIAL NUMBER).  
APPLICATION NUMBER  
MACHINE SERIAL NUMBER  
PRODUCT KEY  
XXXXXXXXX  
7) Obtain the product key with APPLICATION NUMBER and  
MACHINE SERIAL NUMBER in the product sheet.  
For specific procedure to obtain the product key, contact the  
TOSHIBA authorized dealer.  
In addition, keep the product sheet after filling in since the product  
key is important information.  
8) Enter the product key in the web page displayed in 5), and click the  
"Submit" button.  
This completes the PS3 setting.  
9) Select "E-mail status & alerts" from the "Option Name" list in the  
"Product Key Setting" screen.  
10) Click the "Submit" button.  
This completes the e-mail status & alerts function setting.  
GA-1170 SETUP IN A WINDOWS ENVIRONMENT  
4 – 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[ 5 ] Updating Network Box Firmware  
Update the Network Box firmware in the following procedure using a  
Web browser.  
The page changes to the Network Box firmware upload mode.  
The browser is automatically reloaded and then the screen looks  
like this.  
1. Display the web page for updating Network Box firmware  
Start the browser on your PC and specify the following URL. A web  
page, as shown in Fig. 1, appears on screen.  
*When the screen shown in fig.3 is not displayed, refresh a browser  
manually.  
[Fig. 3: Upload mode]  
3. Specifying the file  
[Fig.1: Web page for updating Network Box firmware]  
2. Switch to firmware upload mode  
Click the Browse button. Selects the firmware of the Network Box  
version you want to update, from the file selection menu indicated in  
Fig.4.  
Click the button on the screen, the message shown in Fig. 2  
appears.  
[Fig. 4: Specifying the file]  
Note: If you want to set the IP address of the Network Box at first, use  
the NIC Manager. Select and set your model name and an  
appropriate Ethernet address from the list.  
Both the Boot and Main files can be updated in the same proce-  
dure as mentioned above. However, when you want to update  
both at the same time, you need to update them separately by  
repeating the same procedure twice.  
[Fig.2: Switch to firmware upload mode]  
When updating both files, it is required to first update Boot and  
then Main.  
GA-1170 Updating Network Box Firmware  
5 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Updating the firmware  
Caution: If a DHCP is used, the browser may not be able to reload auto-  
matically in some cases when transferring to the upload mode  
because different IP addresses are read. Therefore, we rec-  
ommend that you use a fixed IP address when updating firm-  
ware.  
After you select the file, click the Submit button. The firmware is  
transmitted to Network Box, and it is updated. The message indi-  
cated in Fig.5 blinks repeatedly until the updating process is com-  
pleted. Do not turn off the power supply.  
If the upload mode is operating with different IP addresses,  
check the IP address obtained by the Ethernet address of Net-  
work Box from the DHCP server and display the updating  
mode URL again using the browser.  
When a proxy server is used, the screen may not be updated  
by reloading. In that case, you need to update manually.  
[Fig.5: Updating in progress]  
5. Restarting your MFP  
When updating is completed, the message shown in Fig.6 appears  
on screen. Turn off the power and then turn it on again to restart  
Network Box.  
[Fig.6: Updating completed]  
GA-1170 Updating Network Box Firmware  
5 – 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
[ 6 ] TROUBLE CODE  
1. TROUBLE CODE (CE CODE)  
If "CE" blinks in the display, press the [START] key. An error code will  
appear.(Only e-STUDIO162/162D, e-STUDIO151/151D displays an error  
code automatically.) Solve the problem as explained below.  
Error Code  
CE-00  
Solution  
Error which cannot be specified occurred.  
Turn off the power and turn it back on. Consult with  
your network administrator to make sure that no prob-  
lems exist on the network or in the server.  
CE-01  
CE-02  
Network Server card error.  
Turn off the power and turn it back on. Consult with  
your network administrator to make sure that no prob-  
lems exist on the network or in the server.  
Server access denied. The scanned image was not  
sent because a connection to the server could not be  
established. Make sure that the SMTP server settings  
or FTP server settings in the Web page are correct.  
CE-03  
CE-04  
CE-05  
The scanned image was not sent because the server  
was busy or there was too much traffic. Wait briefly and  
then try again.  
It has not logged in to the FTP server and the mail  
server. Please reconfirm the login name and a pass-  
word.  
The scanned image was not sent because the directory  
of the destination FTP server was not correct. Make  
sure that the correct FTP server information is config-  
ured in the Web page.  
CE-09  
CE-10  
CE-11  
The size of the scanned image file exceeds the upper  
limit set in "Maximum Size of File" in the Web page.  
Reduce the number of original pages scanned into the  
file, or change the upper limit set in "Maximum Size of  
File".  
A transmission method assigned to a [SCAN MENU]  
key cannot be used. Check the transmission methods  
assigned to the [SCAN MENU] keys in "Enable Scan-  
ner Delivery to:" in the Web page whether or not the  
method can be used.  
The memory filled with scanner data.  
It was not able to process by the size of a scanner data  
being too large.  
Please drop resolution of data by setup of scaner and  
retry scan.  
CE-12  
The quantity of the result for which LDAP searched  
exceeded the maximum quantity which can be  
searched.  
There are too many addresses which were in agree-  
ment with reference conditions.  
Please increase the number of reference characters  
and perform re-reference.  
GA-1170 TROUBLE CODE  
6 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
s l o t 2 3 2 M B  
R O M )  
L D [ 3 1 : 0 ]  
F l a s h S O - D I M M ( M a s k  
M E M D [ 6 3 : 0 ]  
s l o t 1 8 M B  
S O - D I M M  
F l a s h  
L D [ 3 1 : 0 ]  
s l o t 0 1 2 M B o r 1 6 M B  
S O - D I M M  
F l a s h  
M E M D [ 3 1 : 1 6 ]  
M E M D [ 1 5 : 0 ]  
M E M D [ 3 1 : 0 ]  
L C X 2 4 5  
L C X 2 4 4  
L C H  
L C X 3 7 3  
G - B u s  
I M - B u s  
U A R T C h 1  
I S P 1 5 6 1  
( M A C / P H Y )  
D P 8 3 8 1 6  
U S B 2 . 0  
C o n n e c t o r  
P C I  
C o n n e c t o r  
U S B  
C o n n e c t o r  
E t h e r n e t  
GA-1170 CIRCUIT DIAGRAM  
7 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
N O A S M  
1 K  
1 K  
1 K  
1 K  
R 2 5 0  
R 2 4 9  
R 2 4 8  
R 2 4 7  
1 K  
1 K  
1 K  
1 K  
R 3 0 0  
R 2 9 8  
R 2 9 7  
R 2 9 6  
1 0 K  
R 1 7  
1 K  
1 K  
1 K  
R 2 7  
R 2 4  
R 2 2  
R 2 8 7  
2
1 K  
1
1
1 0 K  
R 1 5  
R 1 4  
8 . 2 K  
8 . 2 K  
8 . 2 K  
R 1 9  
R 1 8  
R 2 0  
1 K  
GA-1170 CIRCUIT DIAGRAM  
7 – 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T P 1  
1
GA-1170 CIRCUIT DIAGRAM  
7 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
1
2
1
1 0 u F C 9  
0 . 1 u F C 8  
B L M 4 1 P L 6 2 0 0 S  
B L M 4 1 L P 4 6 0 0 S  
1 0  
1 0  
R 7 3  
R 7 2  
1 0  
1 0  
R 7 7  
R 7 6  
1 0 0 0 p F  
C 7  
1 0 0 0 p F  
C 6  
1 0  
1 0  
R 7 1  
R 7 0  
1
1 0  
1 0  
R 7 5  
R 7 4  
1
0 . 1 u F  
C 5  
1 0 u F  
2
2
C 4  
L 1  
B L M 4 1 P 6 0 0 S  
L 3  
B L M 4 1 P 6 0 0 S  
R 8 9  
R 8 8  
0
0
1 0 K  
4
3
2
1
5
6
7
8
B R 2 9  
8 . 2 K  
R 8 5  
R 8 4  
R 8 3  
R 8 2  
R 8 1  
R 8 0  
R 7 9  
R 7 8  
8 . 2 K  
8 . 2 K  
8 . 2 K  
8 . 2 K  
8 . 2 K  
8 . 2 K  
8 . 2 K  
GA-1170 CIRCUIT DIAGRAM  
7 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 2 u F / 1 6 V  
0 . 1 u F  
C 7 5  
C 7 8  
0 . 1 u F  
0 . 1 u F  
C 7 7  
C 7 6  
1 0 K  
R 1 0 5  
1 0 K  
R 1 0 6  
GA-1170 CIRCUIT DIAGRAM  
7 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 0  
R 1 2 1  
1 0 K  
R 1 2 4  
2 . 2 K  
R 1 2 5  
B
C
E
1 0 K R 1 2 3  
O F F  
O N < - >  
B A T T E R Y  
3 . 3 K  
R 1 2 2  
GA-1170 CIRCUIT DIAGRAM  
7 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 0 K  
R 1 4 5  
1 0 K  
R 1 4 4  
N O A S M  
R 1 4 3  
1 K  
1 0 K  
1 0 K  
R 2 8 6  
R 2 8 5  
1 0 K _ 1 %  
R 1 4 2  
5 4 . 9  
R 1 3 2  
5 4 . 9  
R 1 3 5  
4 9 . 9  
R 1 2 8  
4 9 . 9  
R 1 3 0  
GA-1170 CIRCUIT DIAGRAM  
7 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A V A U X  
A V A U X  
A V A U X  
A V A U X  
1 2 1  
1 1 5  
1 0 8  
9 3  
G N D _ R R E F  
9 4  
1
2
V A U X  
V A U X  
8 5  
5
A G N D  
1 2 4  
A G N D  
1 1 8  
A G N D  
1 1 1  
A V A U X _ P L L  
A G N D  
1 0 4  
1 0 1  
V D D  
D G N D  
1 2 8  
8 0  
7 3  
6 5  
5 7  
4 9  
4 1  
3 3  
2 5  
1 7  
1 0  
V D D  
V D D  
V D D  
V D D  
V D D  
V D D  
V D D  
V D D  
V D D  
D G N D  
8 6  
D G N D  
8 3  
D G N D  
7 6  
D G N D  
6 9  
D G N D  
6 1  
D G N D  
5 3  
D G N D  
4 5  
D G N D  
3 7  
D G N D  
2 9  
D G N D  
2 1  
D G N D  
1 4  
D G N D  
6
GA-1170 CIRCUIT DIAGRAM  
7 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 0 K  
R 1 8 9  
1 0 K  
R 1 9 4  
GA-1170 CIRCUIT DIAGRAM  
7 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
1
1
1
1
1
1
2
1
2
1
2
P . G N D 2  
1 6  
P . G N D 1  
8
1
2
1
2
V B  
G N D  
2 6  
2 4  
G N D  
4
O S C  
3
V r e f  
2
V b o o t  
7
L C  
5
1
2
C S  
C D  
C T  
1
8
3
4
C S  
C D  
C T  
1
8
3
4
G N D  
G N D  
1
2
1
2
1
2
1
2
1
2
2
1
GA-1170 CIRCUIT DIAGRAM  
7 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 CIRCUIT DIAGRAM  
7 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 PARTS LAYOUT  
8 – 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GA-1170 PARTS LAYOUT  
8 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION FOR BATTERY REPLACEMENT  
(Danish)  
ADVARSEL !  
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.  
Udskiftning må kun ske med batteri  
af samme fabrikat og type.  
Levér det brugte batteri tilbage til leverandoren.  
(English)  
Caution !  
Danger of explosion if battery is incorrectly replaced.  
Replace only with the same or equivalent type  
recommended by the manufacturer.  
Dispose of used batteries according to manufacturer's instructions.  
(Finnish)  
VAROITUS  
Paristo voi räjähtää,jos se on virheellisesti asennettu.  
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan  
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden  
mukaisesti.  
(French)  
ATTENTION  
ll y a danger d'explosion s'il y a remplacement incorrect  
de la batterie. Remplacer uniquement avec une batterie du  
même type on d'un type équivalent recommandé par  
leconstructeur.  
Mettre au rébut les batteries usagées conformément aux  
instructions du fabricant.  
(Swedish)  
VARNING  
Explosionsfara vid felaktigt batteribyte.  
Använd samma batterityp eller en ekvivalent  
typ som rekornmenderas av apparattillverkaren.  
Kassera använt batteri enligt fabrikantens  
Instruktion.  
(German)  
Achtung  
Explosionsgefahr bei Verwendung inkorrekter Batterien.  
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder  
vom Hersteller empfohlene Batterien verwendet werden.  
Entsorgung der gebrauchten Batterien nur nach den vom  
Hersteller angegebenen Anwerisugen.  
CAUTION FOR BATTERY DISPOSAL  
(For USA,CANADA)  
"BATTERY DISPOSAL"  
THIS PRODUCT CONTAINS A LITHIUM PRIMARY  
(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY  
THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE  
BATTERY FROM THE PRODUCT AND CONTACT YOUR  
LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION  
ON RECYCLING AND DISPOSAL OPTIONS.  
"TRAITEMENT DES PILES USAGÉES"  
CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE  
MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANESE)  
QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA  
PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE  
AGENCE ENVIRONNEMENTALE LOCALE POUR DES  
INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET  
DE TRAITEMENT.  
GA-1170  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– 1 –  
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Toastmaster Rice Cooker TRC7 User Manual
Toshiba Computer Drive SD R6472 User Manual
Toshiba CRT Television 26HF66 User Manual
Toshiba DVD Player SD K750 User Manual
Toshiba TV Mount WAL7C User Manual
TP Link Network Card T4UH User Manual
Troy Bilt Tiller 12155 User Manual
Victory Refrigeration Refrigerator GRS 1 S7 User Manual
Viking Convection Oven VESO1302T VEDO1302T User Manual
Vivotek Stereo Receiver RX7101 User Manual