Toshiba LAN connected MFPs with Network Viewer, ImageVision2000 or
SmartLink2000
The Toshiba Network Viewer, ImageVision2000 and SmartLink2000 products support the following
Toshiba MFPs when connected using a Network Interface Card [NIC]:
Toshiba DP120F
Toshiba DP125F
Toshiba e-STUDIO16
Toshiba e-STUDIO20
Toshiba e-STUDIO25
• TCP/IP is used to transport instructions and messages between the PC running the device
driver and the Toshiba MFP – so the LAN must support TCP/IP protocol and this protocol
must be installed at least on the PC running the Network Viewer or SmartLink2000 device
driver.
• SMTP is used to send messages between the PC running the device driver and the Toshiba
MFP to send or receive fax messages.
To achieve this the device driver installs itself as a simple SMTP server – this means that no
other SMTP server can run on the PC that is running the Network Viewer or a
SmartLink2000/ImageVision2000 device driver for a Toshiba MFP connected via NIC to the
LAN.
• To send faxes from ImageVision2000/SmartLink2000 via a Toshiba MFP connected directly
to the LAN, SMTP protocol is used.
This means that, on the Toshiba MFP, “E-Mail, Receive Mode” must be set to “SMTP” and
the “Offramp Gateway” function on the Toshiba MFP must be set “ON”.
• The Network Viewer, ImageVision2000 and SmartLink2000 use FTP to exchange device and
phonebook setup data with the Toshiba MFP that allows users to configure the device settings,
One Touch, Abbreviated Dials and Groups for the Toshiba MFP from the PC. FTP access is
protected by a username and password – so the username and password set on the Toshiba
MFP must match those set for the device driver.
Configuring Toshiba MFP
Summary
To use a Toshiba MFP connected directly to the LAN with the Toshiba Network Viewer,
ImageVision2000 or SmartLink2000 you must define the following settings on the Toshiba MFP:
• Either:
Program|Menu Æ INITIAL SETUP Æ NETWORK Æ TCP/IP Æ BOOTP/DCHP
Or:
Program|Menu Æ INITIAL SETUP Æ NETWORK Æ TCP/IP Æ IP ADDRESS
Program|Menu Æ INITIAL SETUP Æ NETWORK Æ TCP/IP Æ SUBNET MASK
Program|Menu Æ INITIAL SETUP Æ NETWORK Æ TCP/IP Æ DEFAULT GATEWAY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
By default the device driver for Toshiba MFPs connected via a LAN will detect the IP being used by the
Toshiba MFP each time the driver starts because the “Determine IP Address every time driver loads”
option is selected:
So, after detecting the Toshiba MFP during installation (or entering the IP assigned to it at that time
manually) the device driver will work whether a static or dynamically allocated IP address is used.
• The “MAC address” of the Toshiba MFP’s network card, which is unique and always remains
the same, is stored in the device driver’s configuration file. Then, when the device driver
starts it broadcasts an SNMP message around the network to find the NIC with the required
MAC address and then learns the IP currently assigned to the card which it then uses for
subsequent communications with the Toshiba MFP.
• The SNMP message will only reach devices in the same sub-net as the PC issuing the message
– the PC where the device driver is running. So, if the Toshiba LAN MFP is in a different
sub-net to the PC running the device driver you cannot use the “Determine IP Address every
time driver loads” option and must set a static IP address for the Toshiba LAN MFP.
1.1.1.2.
IP ADDRESS
Do not set this if the MFP should obtain its IP from a DHCP server – if a specific IP is set then this will
be used even if BOOTP/DHCP defined above is set to “Enable”.
If set, this should be a valid, unique address on the local network. This address later gets entered into
the setup if the device isn't being automatically detected.
The Network Administrator should be able to tell you what this should be.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1.1.3.
SUBNET MASK
This should be a valid net mask for the local network, e.g. 255.255.255.0.
The Network Administrator should be able to tell you what this should be, or you could try running
IPCONFIG.EXE on a LAN PC to see what it is set to on the PC – it may be the same for the Toshiba
MFP.
1.1.1.4.
DEFAULT GATEWAY
The local network's gateway IP address, or you could try running IPCONFIG.EXE on a LAN PC to see
what it is set to on the PC – it may be the same for the Toshiba MFP.
The Network Administrator should be able to tell you what this should be.
1.1.1.5.
HOST NAME = “Domain Name” setting defined for device driver
Used to be used by the IFAX NIC to validate the source of fax transmission jobs received via the NIC
and therefore had to match the "Domain name" defined in ImageVision2000/SmartLink2000 for the
device. However, latest firmware doesn't check the domain used to submit a fax transmission job
against this HOST NAME and instead only accepts new fax transmission jobs from the PC with IP
matching that defined for the MFP’s LAN FAX SERVER ADDRESS.
For safety and simplicity it is probably best though to still set the Toshiba MFP’s HOST NAME" and
device driver’s "Domain name" values to the same settings. e.g. "wordcraft.com".
After changing any settings in the INITIAL SETUP, NETWORK, TCP/IP section press “Cancel” to
return to the INITIAL SETUP, NETWORK section and select “01 COMPLETE” or “01 DONE” to save
the changes.
• If you change the HOST NAME setting on the MFP via the Device Settings function in either
Network Viewer, ImageVision2000 or SmartLink2000 then the “Domain Name” setting
associated with the device driver is automatically updated to match.
1.1.2.
E-MAIL
1.1.2.1.
E-MAIL ADDRESS
You must define a valid email address, even if only using the Toshiba MFP to send fax messages from
ImageVision2000/SmartLink2000.
• If you do not define a valid email address for this setting then the Toshiba MFP will not send a
Message Disposition Notification [MDN] to ImageVision2000/SmartLink2000 when a fax
transmission submitted by ImageVision2000/SmartLink2000 completes whether successfully
or unsuccessfully.
This means that ImageVision2000/Smartlink2000 will show the fax transmission “In
Progress” for 30 minutes while it waits for the MDN after which it will fail the attempt back to
the Scheduler. If the job is then retried still without a valid email address being defined on the
Toshiba MFP the sequence will repeat.
1.1.2.2.
The email address to which error messages should forwarded when appropriate.
1.1.2.3. RECEIVE MODE = SMTP
ERROR MAIL FW ADDRESS
To use the Toshiba MFP to send messages to fax numbers from ImageVision2000/SmartLink2000
“SMTP” must be selected for this setting
1.1.2.4.
SMTP SERVER ADDRESS
Enter the IP address of the SMTP mail server to be used by the Toshiba MFP to send emails.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
If you only want to use the Toshiba MFP to send faxes from ImageVision2000/SmartLink2000 and do
not have an SMTP server IP to use for sending emails from the Toshiba MFP then set the IP of the PC
where ImageVision2000/SmartLink2000’s device driver for this Toshiba MFP is running.
1.1.3.
FTP
1.1.3.1.
FTP SERVER LOGIN NAME = “FTP User” setting defined for the device driver –
default is “public”
1.1.3.2.
FTP SERVER LOGIN PASSWORD = “FTP Password” setting defined for the
device driver – default is “pass”
FTP is used to exchange device setup data between the Network Viewer, ImageVision2000 or
SmartLink2000 and the Toshiba MFP.
• If the FTP user and password settings on the Toshiba MFP do not match those associated with
the device driver in either Network Viewer, ImageVision2000 or SmartLink2000 then
attempts to read setup data from the Toshiba MFP will fail with “Invalid credentials for
setup”.
Check the “FTP User” and “FTP Password” settings in the “File Transfer” section of the
dialog displayed in Network Viewer, ImageVision2000 or SmartLink2000 when you do the
following:
• Start Network Viewer, ImageVision2000 or SmartLink2000
• If Welcome screen appears click “Browse Folders”
• In left-hand folder tree, click “Devices” to open the “Devices” folder
• Right-click appropriate device driver name and select “Properties”.
• Select the “Network” tab
• The following dialog appears:
5
Download from Www.Somanuals.com. All Manuals Search And Download.
match the FTP SERVER LOGIN NAME and FTP SERVER LOGIN PASSWORD settings on
the MFP using the MFP’s front panel:
• Program|Menu Æ INITIAL SETUP Æ NETWORK Æ FTP Æ FTP SERVER LOGIN
NAME
• Program|Menu Æ INITIAL SETUP Æ NETWORK Æ FTP Æ FTP SERVER LOGIN
PASSWORD
• If you change the FTP SERVER LOGIN NAME or FTP SERVER LOGIN PASSWORD
settings on the MFP via the Device Settings function in Network Viewer, ImageVision2000 or
SmartLink2000 then the “FTP User” and “FTP Password” settings associated with the device
driver are automatically updated to match.
1.1.4.
1.1.4.1.
LAN FAX
LAN FAX SERVER ADDRESS = IP of PC running the device driver for this MFP
The Toshiba MFP only accepts messages for transmission to fax numbers from a PC with this IP.
• If the IP of the PC where ImageVision2000/SmartLink2000’s device driver for this Toshiba
MFP doesn’t match the IP defined for the LAN FAX SERVER ADDRESS on the Toshiba
MFP then fax transmissions from ImageVision2000/SmartLink2000 will fail immediately,
with errors such as “Remote fax abandoned”.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Communication
Check NIC is receiving power
Check the LED indicators on the Toshiba MFP’s NIC:
• Green LED is lit while the NIC is properly connected to the LAN
• Amber LED blinks while data is being communicated
Check the PC where Network Viewer, ImageVision2000 or SmartLink2000 will run
can “see” the Toshiba MFP
At the Network Viewer/ImageVision2000/SmartLink2000 PC…
• Click “Start, Run”
• Type:
PING -T aaa.bbb.ccc.ddd
Where aaa.bbb.ccc.ddd is the IP of the Toshiba MFP
• Press ENTER
The PC will then send, at regular intervals, a small message to the Toshiba MFP’s IP and report whether
a response is received or not (if not a timeout will be reported) and if so how quickly.
Responses should be received to 99% of messages and should be received quickly, say less that 10ms
ideally.
If no responses are ever received:
• Check the IP address set on the Toshiba MFP matches the IP used in the PING command.
• Check that no firewall on the PC is preventing the message going out from the PC or coming in from
the Toshiba – maybe disable any personal firewall on the PC as a test to see if the results change.
If responses sometimes timeout and aren’t received:
• Examine the network cabling and infrastructure (including HUBS) and try pinging other PCs and
devices to see if they respond any better.
If other PCs or devices respond more reliably then maybe there’s a problem with the Toshiba MFP’s
NIC or the cables between the PC issuing the PING command and the Toshiba MFP – maybe try
different cable to the Toshiba MFP or a different port in a HUB if one is being used.
Press CTRL and C to stop the PING program.
Check for SMTP Server running on the PC intended to run Network Viewer,
ImageVision2000 or SmartLink2000’s device driver
Before installing Network Viewer, ImageVision2000 or SmartLink2000 or while
neither are running
At the Network Viewer/ImageVision2000/SmartLink2000 PC…
Windows 95(OSR2)/98/Me/NT4:
• Click “Start, Run”
• Type:
TELNET 127.0.0.1 25
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Press ENTER
Windows 2000/XP
• Start a command prompt:
Click “Start, Programs, Accessories, Command Prompt”
• Type:
TELNET 127.0.0.1 25
• Press ENTER
If there is no SMTP server running you should see a message box saying something like:
Could not open a connection to 127.0.0.1
This is good, there is no existing SMTP server running on the PC. The Network
Viewer/ImageVision2000/SmartLink2000 device driver should be able to set up its SMTP server
without conflicting with an existing SMTP server.
If there is already an SMTP server running on this PC you should see something like:
220 somwhere.com NTMail (v6.04.0010/NT9682.00.22282d95) ready for ESMTP transfer
This is not good, there is an existing SMTP server running on the PC. You will not be able to start the
device driver on this PC without first closing whatever SMTP server is already running. The wording of
the “220” message may give you a clue about what is running the SMTP server so you can find it and
close it.
Type “QUIT” and press ENTER to exit TELNET.
After installing Network Viewer/ImageVision2000/SmartLink2000 and while the
software is running
At the Network Viewer/ImageVision2000/SmartLink2000 PC…
Windows 95(OSR2)/98/Me/NT4:
• Click “Start, Run”
• Type:
TELNET 127.0.0.1 25
• Press ENTER
Windows 2000/XP
• Start a command prompt:
Click “Start, Programs, Accessories, Command Prompt”
• Type:
TELNET 127.0.0.1 25
• Press ENTER
You should now see a line that says:
220 Unimessage ESMTP server ready for transfer.
This is good and indicates that the Network Viewer/ImageVision2000/SmartLink2000 SMTP server is
listening correctly.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
If you don't see this line…
• Ensure that the Network Viewer/ImageVision2000/SmartLink2000’s device driver is running (check
the “Devices” folder)
• Examine the Windows System Tray for the Network Viewer/SmartLink2000 device driver’s icon –
it looks like a printer on a LAN cable.
Double click the icon to open the driver’s status window then click the “General” tab and make sure
it says “Waiting for job…”
• Check that no firewall is running on either PC that prevents connections to port 25 on the PC where
the device driver is running from the other PC.
Type “QUIT” and press ENTER to exit TELNET.
Check Network Viewer/ImageVision2000/SmartLink2000’s SMTP server is
accessible from other PCs on the LAN
While the Network Viewer/ImageVision2000/SmartLink2000 is running, on another PC on the LAN…
Windows 95(OSR2)/98/Me/NT4:
• Click “Start, Run”
• Type:
TELNET eee.fff.ggg.hhh 25
Where eee.fff.ggg.hhh is the IP of the PC running Network Viewer or SmartLink2000’s device
driver.
• Press ENTER
Windows 2000/XP
• Start a command prompt:
Click “Start, Programs, Accessories, Command Prompt”
• Type:
TELNET eee.fff.ggg.hhh 25
Where eee.fff.ggg.hhh is the IP of the PC running the device driver.
• Press ENTER
You should now see a line that says:
220 Unimessage ESMTP server ready for transfer.
If you don't see this line…
• Ensure that the Network Viewer/SmartLink2000’s device driver is running (check the “Devices”
folder)
• Examine the Windows System Tray for the Network Viewer/SmartLink2000 device driver’s icon –
it looks like a printer on a LAN cable.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Double click the icon to open the driver’s status window then click the “General” tab and make sure
it says “Waiting for job…”
• Check that no firewall is running on either PC that prevents connections to port 25 on the Network
Viewer/SmartLink2000 PC from the other PC.
Type “QUIT” and press ENTER to exit TELNET.
Check that Network Viewer/ImageVision2000/SmartLink2000 PC can
communicate with Toshiba MFP’s SMTP server
At the Network Viewer/SmartLink2000 PC…
Windows 95(OSR2)/98/Me/NT4:
• Click “Start, Run”
• Type:
TELNET aaa.bbb.ccc.ddd 25
Where aaa.bbb.ccc.ddd is the IP of the Toshiba MFP
• Press ENTER
Windows 2000/XP
• Start a command prompt:
Click “Start, Programs, Accessories, Command Prompt”
• Type:
TELNET aaa.bbb.ccc.ddd 25
Where aaa.bbb.ccc.ddd is the IP of the Toshiba MFP
• Press ENTER
You should now see a line that says:
220 ESMTP Service Ready
If TELNET gets disconnected immediately it is likely that the LAN FAX SRV ADDRESS is set
incorrectly on the Toshiba MFP. If it remains connected, type "QUIT" [ENTER] to exit from the server.
Check can send fax messages successfully from
ImageVision2000/SmartLink2000 via Toshiba MFP
1. Start ImageVision2000/SmartLink2000.
2. Create a new message to a fax number:
a. If Welcome is visible, click “Browse Folders” to open the main display.
b. Press Ctrl+N
c. Enter a fax number into the “To:” field.
d. Enter a brief Subject and Message.
e. Click “Send”
The job should enter ImageVision2000/SmartLink2000’s Outbox and shortly change status from
“Pending” to “In Progress”.
• If the job shows a status of “Problem” the text after the word “Problem” should indicate
10
Download from Www.Somanuals.com. All Manuals Search And Download.
what is wrong
e.g. “No active device” or “No device to deliver by selected distribution method”
might indicate that the device driver is not running – to correct this problem, open
“Devices” folder, select the device and click the green “Start” button in the
“Devices” folder’s toolbar.
3. If the job fails immediately with, for example, “Remote fax abandoned” – check the LAN FAX
SERVER ADDRESS setting on the Toshiba MFP matches the IP address of the PC where Network
Viewer, ImageVision2000 or SmartLink2000’s device driver is running.
You can change this setting either via the front panel of the Toshiba MFP:
• Program|Menu
• INITIAL SETUP
• NETWORK
• LAN FAX
• LAN FAX SERVER ADDRESS
Or via the “Device settings” function in ImageVision2000/SmartLink2000:
• Start ImageVision2000/SmartLink2000.
• If Welcome screen appear, click “Browse Folders” button.
• In left-hand folder tree, click “Devices” to open the “Devices” folder.
• If the appropriate device driver is not already running, right-click the device driver name and
select “Launch fax”.
• Right-click the appropriate device driver name and select “Device settings”.
• Change the setting.
• Click the “Write settings” button.
• You can run IPCONFIG.EXE in a Command Prompt on the PC to learn the PC’s IP
address.
4. If the job remains “In progress” indefinitely1 as shown in ImageVision2000/SmartLink2000’s
Outbox, then verify that the intended recipient of the fax actually received it or print the TX
REPORT on the Toshiba MFP to see if the job was sent successfully as well as verifying the LCD
screen is not displaying any errors.
If the fax message was received OK, the Toshiba MFP TX Report indicates it was sent OK and the
Toshiba MFP’s LCD is not showing any error: check that the INITIAL SETUP Æ NETWORK Æ
E-MAIL Æ E-MAIL ADDRESS setting on the Toshiba MFP is set to a syntactically valid email
address – if it isn’t the Toshiba MFP doesn’t send an MDN message back to
ImageVision2000/SmartLink2000 reporting the outcome of the fax transmission.
If all seems well, enable logging as detailed below:
• Collect a set of logs (see below).
• Write a description of the sequence of events that lead to the job remaining “In progress” in
definitely.
1
Leave at least 5 minutes after the transmission completes for the Toshiba MFP to send the MDN outcome message back
to ImageVision2000/SmartLink2000 before deciding that it is not going to do so.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
• Collect the .DEV file from the main ImageVision2000/SmartLink2000 program files folder
named after your device.
• Collect a Function List printed by the Toshiba MFP
Check can read setup data from Toshiba MFP into Network
Viewer/SmartLink2000
1. Start Network Viewer, ImageVision2000 or SmartLink2000.
2. If Welcome is visible, click “Browse Folders” to open the main display.
3. In the left-hand folder tree, select “Devices” to open the Devices folder.
4. Right click the appropriate device name and if present select “Launch fax” from the menu – if this
menu is not present this means the device driver is already running and you may continue with the
next step.
5. Right click the appropriate device name and select “Device settings” – Network
Viewer/ImageVision2000/SmartLink2000 should start to read setup data from the Toshiba MFP.
6. If all is well a Device Settings screen similar to the one shown below should appear:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7. If the above doesn’t appear or an error such as “Invalid credentials for setup” appears:
• Check that the INITIAL SETUP Æ NETWORK Æ FTP Æ FTP SERVER LOGIN NAME
setting on the Toshiba MFP matches exactly the “FTP User” setting defined for the device driver.
• Check that the INITIAL SETUP Æ NETWORK Æ FTP Æ FTP SERVER LOGIN
PASSWORD setting on the Toshiba MFP matches exactly the “FTP Password” setting defined
for the device driver.
• You can review and edit the current settings for “FTP User” and “FTP Password” in
Network Viewer, ImageVision2000 or SmartLink2000 as detailed below:
• Start Network Viewer, ImageVision2000 or SmartLink2000
• If Welcome screen appears click “Browse Folders”
• In left-hand folder tree, click “Devices” to open the “Devices” folder
• Right-click appropriate device driver name and select “Properties”.
• Select the “Network” tab
• The following dialog appears:
Enabling Network Viewer, ImageVision2000 or SmartLink2000 device driver
logging
1. Launch Windows Explorer
2. Browse into the main Network Viewer, ImageVision2000 or SmartLink2000 program files folder
13
Download from Www.Somanuals.com. All Manuals Search And Download.
e.g.
C:\Program Files\Unimessage Pro
C:\Program Files\SmartLink
3. Locate the .DEV file named after the device driver you have defined in Network
Viewer/ImageVision2000/SmartLink2000 to communicate with and control the LAN connected
Toshiba MFP.
4. Open this file using any available text editor, e.g. Windows NotePad.
5. Add the following two lines after the [Network] section heading:
Log=C:\TECDRV#.LOG
LogData=1
6. Save the edited file back to disk
7. Restart Network Viewer/ImageVision2000/SmartLink2000 – the device driver should start
producing TECDRV*.LOG files in C:\ - these are the files you need to collect to send to
[email protected] after reproducing a problem and then shutting down Network
Viewer/ImageVision2000/SmartLink2000.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|