TOSHIBA Satellite U300 /
Satellite Pro U300 / PORTEGE
M600 / TECRA M8 Series
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Trademarks
Intel, Centrino, Intel Core and Celeron are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the United States and
other countries.
®
Windows and Microsoft are registered trademark of Microsoft
Corporation.
Photo CD is a trademark of Eastman Kodak.
Other trademarks and registered trademarks not listed above may be used
in this manual.
FCC information
FCC notice “Declaration of Conformity Information”
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer’s external monitor port, USB port, serial port,
parallel port, PS/2 mouse/keyboard port and microphone jack. Changes or
modifications made to this equipment, not expressly approved by
TOSHIBA or parties authorized by TOSHIBA could void the user’s
authority to operate the equipment.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Contact
Address:
TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: (949) 583-3000
EU Declaration of Conformity
TOSHIBA declares that this product conforms to the following Standards:
Supplementary
Information:
“The product complies with the requirements of
the Low Voltage Directive 73/23/EEC, the EMC
Directive 89/336/EEC and/or the R&TTE Directive
1999/5/EC.”
This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe,
Hammfelddamm 8, 41460 Neuss, Germany.
iv
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
VCCI Class B Information
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by
TOSHIBA Corporation could void your authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouileur du Canada.
Modem warning notice
Conformity Statement
The equipment has been approved to [Council Decision 98/482/EC - "TBR
21"] for pan-European single terminal connection to the Public Switched
Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in the
first instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.
Germany
ATAAB AN005, AN006, AN007, AN009, AN010 and
DE03, 04, 05, 08, 09,12,14,17
Greece
ATAAB AN005, AN006 and GR01, 02, 03, 04
Portugal
ATAAB AN001, 005, 006, 007, 011 and P03, 04, 08,
10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
v
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Spain
ATAAB AN005, 007, 012, and ES01
ATAAB AN002
Switzerland
All other countries/
regions
ATAAB AN003, 004
Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone
company and give them the following information:
■ The telephone number of the line to which you will connect the modem.
■ The registration number that is located on the device The FCC
registration number of the modem will be found on either the device
which is to be installed, or, if already installed, on the bottom of the
computer outside of the main system label.
■ The Ringer Equivalence Number (REN) of the modem, which can vary.
For the REN of your modem, refer to your modem’s label.
The modem connects to the telephone line by means of a standard jack
called the USOC RJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines.
Connection to telephone company-provided coin service (central office
implemented systems) is prohibited. Connection to party lines service is
subject to state tariffs.
If you have any questions about your telephone line, such as how many
pieces of equipment you can connect to it, the telephone company will
provide this information upon request.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it
can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations, or procedures. If these changes
might affect your service or the operation of your equipment, the telephone
company will give you notice in writing to allow you to make any changes
necessary to maintain uninterrupted service.
vi
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
If problems arise
If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to
the telephone network. If the telephone company notes a problem, they
may temporarily discontinue service. When practical, they will notify you in
advance of this disconnection. If advance notice is not feasible, you will be
notified as soon as possible. When you are notified, you will be given the
opportunity to correct the problem and informed of your right to file a
complaint with the FCC. In the event repairs are ever needed on your
modem, they should be performed by TOSHIBA Corporation or an
authorized representative of TOSHIBA Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message
via a telephone fax machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of
the transmission, the date and time it is sent and an identification of the
business, other entity or individual sending the message and the telephone
number of the sending machine or such business, other entity or individual.
In order to program this information into your fax modem, you should
complete the setup of your fax software before sending messages.
Instructions for IC CS-03 certified equipment
1. The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection.
The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician,
as appropriate.
2. The user manual of analog equipment must contain the equipment’s
Ringer Equivalence Number (REN) and an explanation notice similar to
the following:
The Ringer Equivalence Number (REN) of the modem, which can vary.
For the REN of your modem, refer to your modem’s label.
The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.
3. The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
The IC registration number of the modem is shown below.
IC: 4005B-DELPHI
Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid
Austel permit. This modem has been designed to specifically configure to
ensure compliance with Austel standards when the country/region selection
is set to Australia. The use of other country/region setting while the modem
is attached to the Australian PSTN would result in you modem being
operated in a non-compliant manner. To verify that the country/region is
correctly set, enter the command ATI9 which displays the currently active
setting.
To set the country/region permanently to Australia, enter the following
command sequence:
AT+GCI=09
Failure to set the modem to the Australia country/region setting as shown
above will result in the modem being operated in a non-compliant manner.
Consequently, there would be no permit in force for this equipment and the
Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of
non-permitted equipment.
viii
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Notes for use of this device in New Zealand
■ The grant of a Telepermit for a device in no way indicates Telecom
acceptance of responsibility for the correct operation of that device
under all operating conditions. In particular the higher speeds at which
this modem is capable of operating depend on a specific network
implementation which is only one of many ways of delivering high
quality voice telephony to customers. Failure to operate should not be
reported as a fault to Telecom.
■ In addition to satisfactory line conditions a modem can only work
properly if:
a/ it is compatible with the modem at the other end of the call and
b/ the application using the modem is compatible with the application
at the other end of the call - e.g., accessing the Internet requires
suitable software in addition to a modem.
■ This equipment shall not be used in any manner which could constitute
a nuisance to other Telecom customers.
■ Some parameters required for compliance with Telecom’s PTC
Specifications are dependent on the equipment (PC) associated with
this modem. The associated equipment shall be set to operate within
the following limits for compliance with Telecom Specifications:
a/ There shall be no more than 10 call attempts to the same number
within any 30 minute period for any single manual call initiation, and
b/ The equipment shall go on-hook for a period of not less than 30
seconds between the end of one attempt and the beginning of the
next.
c/ Automatic calls to different numbers shall be not less than 5
seconds apart.
■ Immediately disconnect this equipment should it become physically
damaged, and arrange for its disposal or repair.
■ The correct settings for use with this modem in New Zealand are as
follows:
ATB0 (CCITT operation)
AT&G2 (1800 Hz guard tone)
AT&P1 (Decadic dialling make-break ratio = 33%/67%)
ATS0=0 (not auto answer)
ATS10=less than 150 (loss of carrier to hang up delay, factory default of
15 recommended)
ATS11=90 (DTMF dialling on/off duration=90 ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ix
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
■ When used in the Auto Answer mode, the S0 register must be set with a
value of 3 or 4. This ensures:
■ a person calling your modem will hear a short burst of ringing before
the modem answers. This confirms that the call has been
successfully switched through the network.
■ caller identification information (which occurs between the first and
second ring cadences) is not destroyed.
■ The preferred method of dialling is to use DTMF tones (ATDT...) as this
is faster and more reliable than pulse (decadic) dialling. If for some
reason you must use decadic dialling, your communications program
must be set up to record numbers using the following translation table
as this modem does not implement the New Zealand “Reverse dialling”
standard.
Number to be dialled: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialling is used, the numbers should be entered
normally.
■ The transmit level from this device is set at a fixed level and because of
this there may be circumstances where the performance is less than
optimal. Before reporting such occurrences as faults, please check the
line with a standard Telepermitted telephone, and only report a fault if
the phone performance is impaired.
■ It is recommended that this equipment be disconnected from the
Telecom line during electrical storms.
■ When relocating the equipment, always disconnect the Telecom line
connection before the power connection, and reconnect the power first.
■ This equipment may not be compatible with Telecom Distinctive Alert
cadences and services such as FaxAbility.
NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE
CAUSES MAY INCUR A CHARGE FROM TELECOM
General conditions
As required by PTC 100, please ensure that this office is advised of any
changes to the specifications of these products which might affect
compliance with the relevant PTC Specifications.
The grant of this Telepermit is specific to the above products with the
marketing description as stated on the Telepermit label artwork. The
Telepermit may not be assigned to other parties or other products without
Telecom approval.
A Telepermit artwork for each device is included from which you may
prepare any number of Telepermit labels subject to the general instructions
on format, size and color on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof
to purchasers and service personnel that the product is able to be
legitimately connected to the Telecom network.
The Telepermit label may also be shown on the packaging of the product
and in the sales literature, as required in PTC 100.
x
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
The charge for a Telepermit assessment is $337.50. An additional charge
of $337.50 is payable where an assessment is based on reports against
non-Telecom New Zealand Specifications. $112.50 is charged for each
variation when submitted at the same time as the original.
An invoice for $NZ1237.50 will be sent under separate cover.
Following information is only for EU-member states:
The symbol indicates that this product may not be treated as
household waste. Please ensure this product is properly
disposed as inappropriate waste handling of this product may
cause potential hazards to the environment and human health.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
This symbol may not stick depending on the country and region where you
purchased.
Optical disc drive safety instructions
Be sure to check the international precautions at the end of this section.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xi
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Panasonic
DVD Super Multi UJ-852M/852B
■ The DVD Super Multi drive employs a laser system. To ensure proper
use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.
xii
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
HLDS
DVD Super Multi GSA-U10N
■ The DVD Super Multi drive employs a laser system. To ensure proper
use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xiii
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
International Precautions
CAUTION: This appliance contains a laser
system and is classified as a "CLASS 1
LASER PRODUCT." To use this model
properly, read the instruction manual
carefully and keep this manual for your
future reference. In case of any trouble
with this model, please contact your
nearest "AUTHORIZED service station."
To prevent direct exposure to the laser
beam, do not try to open the enclosure.
VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
"LASERSCHUTZKLASSE 1 PRODUKT"
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf.
Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste "autorisierte Service-Vertretung".
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i
apparatet, at man kan komme til at udsatte
sig for laserstråling.
xiv
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.
CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR
FOLGE HABEN.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xv
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
xvi
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.
Be certain to read the general precautions below and to note the cautions
included in the text of the manual.
Creating a computer-friendly environment
Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.
Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.
To keep your computer in prime operating condition, protect your work area
from:
■ Dust, moisture, and direct sunlight.
■ Equipment that generates a strong electromagnetic field, such as
stereo speakers (other than speakers that are connected to the
computer) or speakerphones.
■ Rapid changes in temperature or humidity and sources of temperature
change such as air conditioner vents or heaters.
■ Extreme heat, cold, or humidity.
■ Liquids and corrosive chemicals.
Stress injury
Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
also includes information on work space design, posture and lighting that
can help reduce physical stress.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xvii
General Precautions
Heat injury
■ Avoid prolonged physical contact with the computer. If the computer is
used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.
■ If the computer has been used for a long time, avoid direct contact with
the metal plate supporting the various interface ports as this can
become hot.
■ The surface of the AC adaptor can become hot when in use but this
condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat as the
material could become damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.
PC and Express Card overheating
Some PC and Express Cards can become hot during prolonged use which
may result in errors or instability in the operation of the device in question.
In addition, you should also be careful when you remove a PC or Express
Card that has been used for a long time.
Mobile phones
Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.
Instruction Manual for Safety and Comfort
All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.
xviii
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Table of Contents
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi
Key operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii
Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Backside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xix
Table of Contents
Installing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Opening the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Turning on the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
Create Optical Recovery Discs
(depends on the model you purchased) . . . . . . . . . . . . . . . . . . . . . .3-10
Restoring the preinstalled software from the Recovery HDD
(depends on the model you purchased) . . . . . . . . . . . . . . . . . . . . . .3-10
Using the TouchPad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
xx
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Writing CD/DVDs with the DVD Super Multi drive
supporting DVD±R Double layer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Important message (DVD Super Multi drive
supporting DVD±R Double layer) . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Disclaimer (DVD Super Multi drive
supporting DVD±R Double layer) . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Media care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
CD/DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
®
®
purchased) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xxi
Table of Contents
®
Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Power indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-13
HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Memory expansion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-7
xxii
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
System start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Self test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
LCD panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Hard disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Pointing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Before you call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Where to write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
User’s Manual
xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
xxiv
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Preface
Congratulations on your purchase of the TOSHIBA Satellite U300 / Satellite
Pro U300 / PORTEGE M600 / TECRA M8 Series computer. This powerful
notebook computer provides excellent expansion capability, including
multimedia devices, and it is designed to provide years of reliable, high-
performance computing.
This manual tells how to set up and begin using your TOSHIBA Satellite
U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series computer.
It also provides detailed information on configuring your computer, basic
operations and care, using optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing,
yourself with the computer's features, components and accessory devices.
computer.
If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the
Specifications section of the Introduction, to learn about features that are
uncommon or unique to the computer. If you are going to install PC Cards
or connect external devices such as a monitor, be sure to read Chapter 8,
Manual contents
This manual is composed of the following nine chapters, five appendixes, a
glossary and an index.
capabilities, and options.
briefly explains how they function.
operating your computer and gives tips on safety and designing your work
area.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xxv
Preface
devices: TouchPad, Sound System, optical media drives, modem, wireless
communication and LAN. It also provides tips on care of the computer, and
CD/DVDs.
the keypad overlay and hot keys.
power resources and battery save modes.
HW Setup program.
some diagnostic tests, and suggests courses of action if the computer
doesn’t seem to be working properly.
acronyms used in the text.
Conventions
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.
Keys
The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.
xxvi
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Key operation
Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, Ctrl + C means you must hold down Ctrl and at the same
time press C. If three keys are used, hold down the first two and at the
same time press the third.
ABC
When procedures require an action such as
clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
type face you see to the left.
Display
Names of windows or icons or text generated by
the computer that appears on its display screen
is presented in the type face you see to the left.
ABC
Messages
Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.
Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.
Please read. A note is a hint or advice that helps you make best use of
your equipment.
Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xxvii
Preface
xxviii
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 1
Introduction
This chapter provides an equipment checklist, and it identifies the
computer's features, options and accessories.
Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for
future use.
Hardware
Check to make sure you have all the following items:
■ TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 /
TECRA M8 Series Portable Personal Computer
■ Universal AC adaptor and power cord
■ Modular cable for modem (optional part dependant on model
purchased)
It is necessary to install the battery to use this computer. Refer to Installing
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1
Introduction
Software
®
®
Microsoft Windows XP Home Edition/ Professional
The following software is preinstalled:
®
®
■ Microsoft Windows XP Home Editon/ Professional
■ Microsoft Internet Explorer
■ TOSHIBA Utilities
■ TOSHIBA Hardware Setup
■ TOSHIBA Supervisor Password
■ TOSHIBA Assist
■ TOSHIBA ConfigFree
■ DVD Video Player
■ TOSHIBA CD/DVD Acoustic Silencer
■ TOSHIBA SD Utilities
■ TOSHIBA Disc Creator
■ Recovery Disc Creator (depends on the model you purchased)
■ Online Manual
■ Display Driver
■ TouchPad Driver
■ Sound Driver
■ Miscellaneous drivers (depending on the model you purchased:
Modem, Wireless LAN)
Other software may be preinstalled dependant on the model purchased.
■ Discs
■ Windows Anytime Upgrade DVD (Is included with some models)
Documentation
■ Satellite U300 / Satellite Pro U300 Series Personal Computer User
Information Guide
®
®
■ Microsoft Windows XP manual package (Provided with some
models)
■ International Limited Warranty (ILW) Instruction (This instruction is
included only with computers sold in ILW supported areas.)
If any of the items are missing or damaged, contact your dealer
immediately.
1-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Features
Please visit your region’s web site for the configuration details of the model
that you have purchased.
Processor
Built-in
Depend on the model you purchased.
®
Intel Core™ 2 Duo Processor
®
Intel Core™ Duo Processor
®
®
Intel Pentium Dual Core Processor
®
®
Intel Celeron M Processor
TJ85 Seam CPU support
®
Chipset
Mobile Intel GM965 Express Chipset
®
Mobile Intel 945GM Express Chipset
®
Mobile Intel 943GML Express Chipset
Memory
Main Memory
Disclaimer
Part of the main system memory may be used by
the graphics system for graphics performance
and therefore reduce the amount of main system
memory available for other computing activities.
The amount of main system memory allocated to
support graphics may vary depending on the
graphics system, applications utilized, system
memory size and other factors. For PC's
configured with 4 GB of system memory, the full
system memory space for computing activities
will be considerably less and will vary by model
and system configuration.
Slots
Up to two 2048 MB memory modules can be
installed in the memory slot for a maximum of 4
GB system memory total.
Video RAM
Depending on the model you purchased:
®
Mobile Intel GM965/GL960/945GM/943GML
Express Chipset, up to 251MB shared with main
memory.
(for more than 1GB main memory)
User’s Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Power
Battery Pack
Your computer is powered by a rechargeable
lithium-ion battery pack.
RTC Battery
AC Adaptor
The internal RTC battery backs up the Real Time
Clock and calendar.
The universal AC adaptor provides power to the
system and recharges the batteries when they
are low. It comes with a detachable power cord.
Because it is universal, it can receive a range of
AC voltage from 100 to 240 volts; however, the
output current varies among different models.
Using the wrong model can damage your
Disks
9
Hard disk Disclaimer
1 Gigabyte (GB) means 10 = 1,000,000,000
bytes using powers of 10. The computer
operating system, however, reports storage
capacity using powers of 2 for the definition of 1
30
GB = 2 = 1,073,741,824 bytes, and therefore
shows less storage capacity. Available storage
capacity will also be less if the product includes
one or more pre-installed operating systems,
such as Microsoft Operating System and/or pre-
installed software applications, or media content.
Actual formatted capacity may vary.
Hard disk Drive
Available in six sizes.
■ 60.0 billion bytes (55.89 GB)
■ 80.0 billion bytes (74.51 GB)
■ 100.0 billion bytes (93.13 GB)
■ 120.0 billion bytes (111.75 GB)
■ 160.0 billion bytes (149.01 GB)
■ 200.0 billion bytes (186.26 GB)
Other hard disk drives may be introduced in the
future.
Computers in this series can be configured with a fixed optical media drive.
The available optical media drives are described below.
1-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
DVD Super Multi
drive (Supporting
DVD±R Double
Layer)
Some models are equipped with a full-size DVD
Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CD/DVDs without
using an adaptor. It reads DVD-ROM's at
maximum 8 speed and CD-ROM's at maximum
24 speed. It writes CD-R's at up to 24 speed,
CD-RW's at up to 16 speed, DVD-R's at
maximum 8 speed, DVD-RW's at maximum 6
speed. DVD+R's at maximum 8 speed,
DVD+RW's at maximum 8 speed, DVD+R(DL)
discs at maximum 4 speed and DVD-R(DL) discs
at maximun 4 speed.
DVD-RAM at maximum 5 speed. This drive
supports the following formats in addition to
DVD-ROM & CD-R/RW drive.
■ DVD+R
■ DVD+RW
■ DVD-RAM
■ DVD-R
■ DVD-RW
■ DVD+R (DL)
■ DVD-R (DL)
Display
The computer's LCD panel supports high-resolution video graphics. The
screen can be set at a wide range of viewing angles for maximum comfort
and readability.
Built-In
13.3” WXGA 16 M colors, with the following
resolution:
1280 horizontal × 800 vertical pixels
Graphics Controller
Graphics controller maximizes display
performance. Refer to Display Controller and
and Modes for more information.
Keyboard
Built-In
84 keys or 85 keys, compatible with IBM
enhanced keyboard, embedded numeric overlay,
dedicated cursor control,
and
keys.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-5
Introduction
Pointing Device
Built-In TouchPad
A TouchPad and control buttons in the palm rest
enable control of the on-screen pointer and
scrolling of windows.
Ports
External Monitor
Depending on the model you purchased:
15-pin, analog VGA port supports VESA DDC2B
compatible functions.
Universal Serial Bus The computer has Universal Serial Bus ports that
(USB 2.0)
comply with the USB 2.0 standard, which
enables data transfer speeds 40 times faster
than the USB 1.1 standard. (The ports also
support USB 1.1.)
i.LINK (IEEE1394a)
This port enables high-speed data transfer
directly from external devices such as digital
video cameras.
Slots
Express Card
The Express Card expansion slot that can
accommodate two standard module formats; an
Express Card/34 module and an Express Card/
54 module. An Express Card module is a small
add-in card technology based on the PCI
Express and Universal Serial Bus (USB)
interfaces.
(Depends on the model purchased)
PC Card
The PC Card slot accommodates Type II card.
(Depends on the model purchased)
Multiple Digital
Media Card Slot
Supports SD Mini SD(with adaptor), MMS, MS,
MS Pro, xD cards.
Multimedia
Web Camera
Record/Send still or video images with this
integrated webcam.
(Depends on the model purchased)
®
Sound System
A Windows Sound System that provides
speakers as well as jacks for an external
microphone and headphones.
1-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Headphone Jack
Microphone Jack
This jack outputs analog audio signals.
A 3.5 mm mini microphone jack enables
connection of a three-conductor mini jack for
monaural microphone input.
Communications
Modem
The internal modem feature is not available on all
models. Where present, it provides capability for
data and fax communication. It supports V.90
(V.92). The speed of data transfer and fax
communication depends on the analog
telephone line conditions. The computer has a
modem jack for connection to a telephone line.
Both V.90 and V.92 are supported only in the
USA, Canada, Australia. V.90 is available in
other regions.
LAN
The computer has built-in support for Ethernet
LAN (10 megabits per second, 10BASE-T) and
Fast Ethernet LAN (100 megabits per second,
100BASE-TX).
Wireless LAN
The Wireless LAN feature is not available on all
models. Where present, it supports the A,B,G
and N standards but it is compatible with other
LAN systems based on Direct Sequence Spread
Spectrum / Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.
■ Automatic Transmit Rate Select mechanism
in the transmit range of 54, 48, 36, 24, 18, 12,
9 and 6 Mbit/s. (IEEE 802.11g)
■ Automatic Transmit Rate Select mechanism in
the transmit range of 11, 5.5, 2 and 1 Mbit/s.
(IEEE 802.11b)
■ Roaming over multiple channels
■ Card Power Management
■ Wired Equivalent Privacy (WEP) data
encryption, based on 128 bit encryption
algorithm.
■ Advanced Encryption Standard (AES) data
encryption, based on 128 bit encryption
algorithm.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-7
Introduction
Security
Password
Power-on password protection
Two level password architecture
Fingerprint authentication (not available on all
models)
Special features
The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.
Hot Keys
Key combinations let you quickly modify the
system configuration directly from the keyboard
without running a system configuration program.
Keypad Overlay
A ten-key pad is integrated into the keyboard.
The Keyboard, for instructions on using the
keypad overlay.
Instant Security
The hot key function Fn + F1 blanks the screen
and disables the computer, providing data
security.
Display Automatic
This feature automatically cuts off power to the
internal display when there is no keyboard input
for a specified time. Power is restored when any
key is pressed.
*1
Power Off
This can be specified in the Power Options.
HDD Automatic
This feature automatically cuts off power to the
hard disc drive when it is not accessed for a
specified time. Power is restored when the hard
disc is accessed.
*1
Power Off
This can be specified in the Power Options.
System Automatic
Standby Mode/
This feature automatically shuts down the system
into Standby Mode or Hibernation Mode when
there is no input or hardware access for a
specified time.
*1
Hibernation
This can be specified in the Power Options.
1-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Intelligent Power
A microprocessor in the computer's intelligent
*1
power supply detects the battery’s charge and
calculates the remaining battery capacity. It also
protects electronic components from abnormal
conditions, such as voltage overload from an
AC adaptor.
Supply
This can be specified in the Power Options.
*1
*1
This feature lets you save battery power.
This can be specified in the Power Options.
Battery Save Mode
Panel Power On/Off
This feature turns power to the computer off
when the display panel is closed and turns it back
on when the panel is opened.
This can be specified in the Power Options.
Low Battery
Automatic
When battery power is exhausted to the point
that computer operation cannot be continued, the
system automatically enters Hibernation Mode
and shuts down.
*1
Hibernation
This can be specified in the Power Options.
TOSHIBA HDD
Protection
This feature uses the acceleration sensor built in
the computer to detect vibration and shocks, and
automatically moves the hard disk drive's read/
write head to a safe position in order to reduce
the risk of damage that could be caused by
headto-disk contact. Refer to the Using the Hard
Disk Drive (HDD) Protection section in Chapter
The TOSHIBA HDD Protection function does not guarantee that the hard
disk drive will not be damaged.
Hibernation
This feature lets you turn off the power without
exiting from your software. The contents of main
memory are saved to the hard disk so that when
you turn on the power again, you can continue
working right where you left off. Refer to the
Turning off the power section in Chapter 3,
Getting Started, for details.
Standby Mode
If you have to interrupt your work, you can turn
off the power without exiting from your software.
Data is maintained in the computer's main
memory so that when you turn on the power
again, you can continue working right where you
left off.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-9
Introduction
*1 Click start, Control Panel, Performance and Maintenance, Power
Options and Alarm tab.
Utilities
This section describes preinstalled utilities and tells how to start them. For
details on operations, refer to each utility’s online manual, help files or
readme.txt files.
TOSHIBA Power
Saver
TOSHIBA Power Saver provides you with the
features of more various power supply
managements.
TOSHIBA Zooming
Utility
This utility allows you to enlarge or reduce the
icon size on the desktop or the application
window.
To run TOSHIBA Zooming Utility, click start,
select All Programs followed by TOSHIBA
followed by Utilities and then click Zooming
Utility.
TOSHIBA PC
Diagnostic Tool
TOSHIBA PC Diagnostic Tool displays the basic
information on the computer's configuration and
allows some of the built-in devices functionality to
be tested. To start the TOSHIBA PC Diagnostic
Tool, click start, point to All Programs, point to
TOSHIBA, and point to Utilities and click PC
Diagnostic Tool.
TOSHIBA
Accessibility
The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the Fn key
'sticky', that is you can press it once, release it,
and then press one of the 'F' keys in order to
access its specific function. When set, the Fn key
will remain active until another key is pressed.
TOSHIBA Assist
HW Setup
TOSHIBA Assist is a graphical user interface that
provides easy access to help and services.
This program lets you customize your hardware
settings according to the way you work with your
computer and the peripherals you use. To start
the utility, double click the TOSHIBA Assist on
your desktop, select OPTIMIZE tab, and click
TOSHIBA Hardware Settings.
1-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Power On Password Two levels of password security, supervisor and
user, are available to prevent unauthorized
access to your computer.
To register a supervisor password, double click
the TOSHIBA Assist on your desktop select the
SECURE tab and start the Supervisor
password utility.
To set a user password, select the SECURE tab
on TOSHIBA Assist, then start the User
password utility. On the Password tab you can
register a user password.
FingerPrint utility
(depends on the
model you
This product has a fingerprint utility installed for
the purpose of enrolling and recognizing
fingerprints. (depending on the model
purchased.) By enrolling the ID and password to
the fingerprint authentication device, it is no
longer necessary to input the password from the
keyboard. Just by swiping the finger against the
fingerprint sensor, the following functions will be
enabled:
purchased)
■ Log-on to Windows and access a security
enabled homepage through IE (Internet
Explorer).
■ Files and folders can be encrypted/decrypted
and third party access to them prevented.
■ Disable the password-protected screensaver
when returning from power-saving (Standby)
mode.
■ System boot authentication and Single Touch
Boot feature.
■ Power on Security and Single Sign On
feature.
TOSHIBA DVD
Player
The DVD Video Player is used to play DVD
Video. It has an on-screen interface and
functions. Click start, point to All Programs,
point to InterVideo WinDVD, then click
InterVideo WinDVD.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-11
Introduction
TOSHIBA Disc
Creator
You can create CD/DVDs in several formats
including audio CDs that can be played on a
standard stereo CD player and data CDs or
DVDs to store multimedia and/or document files
on your hard disk drive. This software can be
used on a model with the CD-RW/DVD-ROM
drive, DVD-R/-RW drive, DVD±R/±RW drive and
DVD Super Multi drive.
To run TOSHIBA Disc Creator, click start, select
All Programs, TOSHIBA, CD&DVD
Applications, and then click Disc Creator.
TOSHIBAConfigFree ConfigFree is a suite of utilities to allow easy
control of communication device and network
connections. ConfigFree also allows you to find
communication problems and create profiles for
easy switching between location and
communication networks.
To run ConfigFree, click start, select All
Programs followed by TOSHIBA followed by
Networking and then click ConfigFree.
TOSHIBA TouchPad Pressing Fn + F9 enables or disables the
On/Off Utility
TouchPad function. When you press these hot
keys, the current setting will change and be
displayed as an icon.
1-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Options
You can add a number of options to make your computer even more
details. The following options are available:
Memory expansion
Two memory modules can be installed in this
computer.
Use only PC5300* compatible DDRII memory modules. See your
TOSHIBA dealer for details.
* The availability of DDRII depends on the model you purchased.
Battery pack
AC Adaptor
An additional battery pack can be purchased
from your TOSHIBA dealer. Use it as a spare to
increase your computer operating time.
If you use your computer at more than one site
frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.
User’s Manual
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-14
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 2
The Grand Tour
This chapter identifies the various components of your computer. Become
familiar with each component before you operate the computer.
Front with the display closed
The following figure shows the computer's front with its display panel in the
closed position.
Power
LED
Hard Disk
Drive LED
Wireless
Activity LED
Multiple Digital
Media Card Slot
DC in
LED
i.LINK (IEEE
1394a) Port
Wireless
Communication
Switch
Battery
LED
Multiple
Digital
Media Card
Slot LED
Front of the computer with display closed
i.LINK (IEEE1394a)
Port
This port allows you to connect an external
device, such as a digital video camera, for
highspeed data transfer.
(Depends on the model you purchased)
Multiple Digital
Media Card Slot
Supports SD, mini SD (thru adaptor), MMS, MS,
MS PRO, xD media cards.
Wireless
Communication
Switch
The Wireless Communication Switch turns on the
wireless networking transceiver. (Depends on the
model you purchased.)
Set the switch to off in airplanes and hospitals. Check the wireless activity
indicator. It will stop glowing when the wireless communication function is
off.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1
The Grand Tour
Wireless Activity
LED
Indicates whether the wireless LAN or Bluetooth
is active or not.
(Depends on the model you purchased.)
DC IN LED
Power LED
The DC IN LED indicates the computer is
connected to the AC adaptor and it is plugged
into an AC power source.
The Power indicator glows blue when the
computer is on. If you select Standby Mode from
Turn Off Computer, this indicator flashes orange
(one second on, two seconds off) while the
computer enters Standby Mode.
Battery LED
The Battery indicator shows the condition of the
battery's charge: Blue indicates a full charge,
orange indicates that the battery is charging and
flashing orange indicates a low battery charge.
Hard Disk Drive LED The Hard Disk Drive LED indicates that the hard
disk drive is being accessed. Every time your
computer runs a program, opens a file, or
performs some other function in which it must
access the hard disk drive, this light will go on.
Multiple Digital
Multiple Digital Media Card Slot LED lights up
Media Card Slot LED when the Multiple Digital Media Card Slot is
accessed.
(Depends on the model you purchased.)
Left side
The following figure shows the computer's left side.
Volume Dial
External Monitor Port
USB Ports
Headphone
Jack
Microphone
Jack
Cooling Vents
The left side of the computer
2-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
External Monitor
Port
This 15-pin port lets you connect an external
video display. The Analog VGA port supports
VESA DDC2B compatible functions. (Depends
on the model you purchased.)
Cooling Vents
Cooling vents help prevent the CPU from
overheating.
Do not block the cooling vents. Also ensure that foreign objects are kept
out of the vents as items such as pins or similar objects, which can
damage the computer's circuitry.
Universal Serial Bus Two Universal Serial Bus ports are on the left
(USB 2.0) ports
side. The ports comply with the USB 2.0
standard, which enable data transfer speeds 40
times faster than the USB 1.1 standard (The
ports also support USB 1.1). Keep foreign
objects out of the USB connectors. A pin or
similar object can damage the computer's
circuitry. Operation of all functions of all USB
devices has not been confirmed. As such, some
untested third-party devices may not function
properly.
Microphone Jack
A 3.5 mm mini microphone jack enables
connection of a three-conductor mini jack for
monaural microphone input.
Headphone Jack
Volume Dial
This jack outputs analog audio signals.
Use this dial to adjust the volume of the stereo
speakers or headphones.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3
The Grand Tour
Right side
The following figure shows the computer's right side.
Eject
Button
ODD
Indicator
Security
Lock
PC/Express
Card Slot
LAN Jack
Emergency
Eject Hole
USB Port
Modem
Jack
The right side of the computer
PC/Express Card
Slot for Cardbus
Card Slot
This slot allows you to insert an Express Card.
An Express Card is a small, modular add-in card
technology based on PCI Express and the
Universal Serial Bus (USB) interface. The max.
transmission rate is 2.5Gbps. Express Card/34
and Express Card/54 types are supported.
A PC Card slot can accommodate Type II cards.
The slot supports 16-bit PC Cards and CardBus
PC Cards.
(Depends on the model purchased)
ODD Indicator
The ODD indicator glows amber when the
computer accesses the optical disc drive.
Emergency Eject
Hole
In the event that the disc drive becomes
inexplicably locked or stops responding press
this button to force a manual ejection of the ODD
tray.
Eject Button
Press this button to open the ODD tray.
Universal Serial Bus A single of Universal Serial Bus port is on the
(USB 2.0) port
right side. The port complies with the USB 2.0
standard, which enables data transfer speeds 40
times faster than the USB 1.1 standard (The
ports also support USB 1.1). Keep foreign
objects out of the USB connectors. A pin or
similar object can damage the computer's
circuitry. Operation of all functions for all USB
devices has not been confirmed. As such, some
untested third-party devices may not function
properly.
2-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
LAN Jack
This jack lets you connect to a LAN. The adaptor
has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second,
100BASE-TX). Refer to Chapter 4, Operating
Basics, for details.
Modem Jack
The modem jack allows you to use a modular
cable to connect the modem directly to a
telephone line. (Depends on the model you
purchased.)
■ In case of a lightning storm, unplug the
modem cable from the telephone jack.
■ Do not connect the modem to a digital
telephone line. A digital line will damage the
modem.
Security Lock
A security cable attaches to this port. The
optional security cable anchors your computer to
a desk or other large object to deter theft.
Backside
The following figure shows the computer's back panel.
DC in 19V Jack
The backside of the computer
DC IN 19V Jack
The AC adaptor connects to this socket. Use
only the model of AC adaptor that comes with the
computer. Using the wrong adaptor can damage
your computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-5
The Grand Tour
Underside
The following figure shows the underside of the computer. Make sure the
display is closed before turning over your computer.
Battery Pack
Battery Release Latch
Battery
Pack
Lock
Memory
Module
and
Wireless
LAN
Cover
Cooling
Vents
Hard Disk Cover
The underside of the computer
Memory Module and This cover protects two memory module sockets --
Wireless LAN Cover one or two modules are pre-installed. Refer to the
Battery Pack Lock
Slide this lock to prepare the battery pack for
removal.
Battery Pack
The battery pack powers the computer when the
AC adaptor is not connected. For detailed
information on the battery pack, refer to
Battery Release
Latch
Slide and hold this latch to release the battery
pack for removal. For detailed information on
removing the battery pack, refer to Chapter 6,
Cooling Vents
Cooling vents help prevent the CPU from
overheating.
Hard Disk Cover
This cover protects the hard disk.
2-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
Front with the display open
This section shows the front of the computer with the display open. Refer to
the appropriate illustration for details. To open the display, lift the front of the
display. Position the display at a comfortable viewing angle.
Web Camera LED
Web Camera
Power Button
Internet Button
CD/ DVD Button
Play/Pause Button
Stop Button
Display
Screen
Previous Button
Next Button
Speaker
TouchPad
Speaker
Fingerprint
Sensor
TouchPad
Control
Buttons
The front of the computer with the display open
Speakers
The speakers emit sound generated by your
software as well as audio alarms, such as low
battery condition, generated by the system.
Display Screen
The LCD displays high-contrast text and
graphics. Refer to Appendix B, Display Controller
and Modes. When the computer operates on the
AC adaptor the display screen’s image will be
somewhat brighter than when it operates on
battery power. The lower brightness level is
intended to save battery power.
Web Camera LED
Web Camera
Web Camera LED indicates web camera is
working or not. (Depends on the model you
purchased.)
Take your picture or send your image to web
contacts. (Depends on the model you
purchased.)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7
The Grand Tour
Power Button
Turns the computer on and off and puts it into
Hibernation mode and wakes it up from Standby
Mode.
Internet Button
Press this button to launch an Internet browser. If
the computer’s power is off, you can press this
button to turn on the computer’s power and
launch the browser automatically in one step.
(Depends on the model you purchased.)
CD/ DVD Button
Pressing this button will launch an application
program that allows for playing of CDs or DVDs.
The application that is launched differs by model:
Windows Media Player/TOSHIBA DVD Player.
(Depends on the model purchased.)
Play/Pause Button
Press this button to begin playing an audio CD, a
DVD movie or digital audio file. This button also
acts as a Pause button.
(Depends on the model purchased.)
Stop Button
Stops playing of the CD, DVD or digital audio.
(Depends on the model purchased.)
Previous Button
Skips backwards to the previous track, chapter or
for details.
(Depends on the model purchased.)
Next Button
Skips forward to the next track, chapter or digital
details.
(Depends on the model purchased.)
Presentation Button Press this button to switch Windows screen to
clone mode display. Default setting is “clone
mode display 1024 x 768” at internal and external
display. You can also set extended mode at
external display. Press again to switch external
display only.
(Depends on the model purchased.)
TOSHIBA Assist
Button
Press this button to launch TOSHIBA Assist
application. If the computer’s power is off, you
can press this button to turn on the computer’s
power and launch the TOSHIBA Assist
application automatically in one step.
(Depends on the model purchased.)
2-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
TouchPad
A TouchPad located in the centre of the palm rest
is used to control the on-screen pointer.
Fingerprint Sensor
Just by swiping the finger against the fingerprint
sensor, the following functions will be enabled:
Log-on to Windows and access a security-
enabled homepage through IE (Internet Explorer)
Files and folders can be encrypted/decrypted
and third party access to them prevented.
Disable the password-protected screensavcr
when returning from power-saving (Standby)
mode. System boot authentication and Single
Touch Boot feature. Authentication of the User
Password and Hard Disk Drive Password when
booting up the computer. Refer to the Using the
Basics. (Depends on the model you purchased.)
TouchPad Control
Buttons
These let you select menu items or manipulate
text and graphics designated by the on-screen
Fixed optical media drives
One of the following optical media drives is installed in the computer, either
a CD-ROM drive or DVD-ROM&CD-R/RW drive or a DVD Super Multi
drive. An ATAPI interface controller is used for CD/DVD operation. When
the computer is accessing a CD/DVD, an indicator on the drive glows.
Region codes for DVD drive and media
DVD-ROM&CD-R/RW drive and the DVD Super Multi drives and their
associated media are manufactured according to the specifications of six
marketing regions. When you purchase DVD-Video, make sure it matches
your drive, otherwise it will not play properly.
Code
Region
1
2
3
4
Canada, United States
Japan, Europe, South Africa, Middle East
Southeast Asia, East Asia
Australia, New Zealand, Pacific Islands, Central
America, South America, Caribbean
5
6
Russia, Indian Subcontinent, Africa, North Korea,
Mongolia
China
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-9
The Grand Tour
Writable discs
This section describes the types of writable CD discs. Check the
specifications of your drive for the type of discs it can write. Use TOSHIBA
CDs
■ CD-R discs can be written only once. The recorded data cannot be
erased or changed.
■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4
multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write
speed of the ultra-speed CD-RW discs (Ultra-speed is available on the
DVD-ROM & CD-R/RW drive only) is a maximum of 24-speed.
Formats
The drives support the following formats:
■ DVD-ROM*
■ CD-DA
■ Photo CD™ (single/multi-session)
■ CD-ROM X A Mode 2 (Form1, Form2)
■ CD-R (Audio CD only)
■ DVD -Video*
■ CD-Text
■ CD-ROM Mode 1, Mode 2
■ Enhanced CD (CD-EXTRA)
■ CD-RW
* Not available on the CD-ROM drive.
2-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
DVD Super Multi drive (Supporting DVD±R Double Layer)
The full-size DVD Super Multi drive module lets you record data to writable
CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.
The read speed is slower at the centre of a disc and faster at the outer
edge.
DVD read
8 speed (maximum)
DVD-R write
DVD-RW write
DVD+R write
DVD+RW write
DVD-R(DL) write
DVD+R(DL) write
DVD-RAM write
CD read
8 speed (maximum)
6 speed (maximum)
8 speed (maximum)
8 speed (maximum)
4 speed (maximum)
4 speed (maximum)
5 speed (maximum)
24 speed (maximum)
24 speed (maximum)
16 speed (maximum, Ultra-speed media)
CD-R write
CD-RW write
AC adaptor
The AC adaptor converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use the computer in almost any country/region.
To recharge the battery, simply connect the AC adaptor to a power source
details.
The AC adaptor
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-11
The Grand Tour
■ Use only the AC adaptor that came with the computer or an equivalent
optional adaptor. Use of the wrong adaptor could damage your
computer. TOSHIBA assumes no liability for any damage in such case.
■ Use only the AC Adaptor supplied with your computer or an equivalent
adaptor that is compatible. Use of any incompatible adaptor or other
types of AC Adaptors may have a different voltage which could cause
damage to your computer, computer failure and/or possible data loss.
TOSHIBA assumes no liability for any damage, computer failure and/or
data loss caused by use of an incompatible adaptor.
Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.
2-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 3
Getting Started
This chapter provides basic information to get you started using your
computer. It covers the following topics:
Be sure also to read the Safety Instruction Manual. This guide, which is
included with the computer, explains product liability.
■ Installing the battery pack
■ Connecting the AC adaptor
■ Opening the display
■ Turning on the power
■ Starting up for the first time
■ Turning off the power
■ Restarting the computer
■ System Recovery Options
■ Create Optical Recovery Discs (depends on the model you purchased)
■ Restoring the preinstalled Software from the Recovery HDD (depends
on the model you purchased)
■ Restoring the Preinstalled Software from Recovery Media
All users should be sure to read the section Starting up for the first time.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-1
Getting Started
Installing the battery pack
To install a battery, follow the steps below.
■ The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.
■ Do not touch the latch while holding the computer. Or you may get
injured by the dropped battery by unintentional release of the latch.
■ Please do not push the power button before installing the battery pack.
1. Turn the computer's power off.
2. Disconnect all cables connected to the computer.
3. Insert the battery pack. The Battery Release Latch clicks into place.
4. Secure the Battery Pack Lock to ensure the battery is locked into place.
Later, when you want to remove the battery you must disengage this
lock first.
Battery Release Latch
Battery
Pack Lock
Securing the battery pack
Power-Up Modes, for removing the battery pack.
3-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Connecting the AC adaptor
Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.
The AC adaptor can be connected to any power source supplying from 100
to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.
■ Use only the AC adaptor supplied with your computer or an equivalent
adaptor that is compatible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no liability for any damage
caused by use of an incompatible adaptor.
■ When you connect the AC adaptor to the computer, always follow the
steps in the exact order as described in the User's Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical change
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.
1. Connect the power cord to the AC adaptor.
Connecting the power cord to the AC adaptor
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3
Getting Started
2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the
back of the computer.
Connecting the adaptor to the computer
3. Plug the power cord into a live wall outlet.
Opening the display
The display panel can be rotated in a wide range of angles for optimal
viewing.
1. Lift the panel up and adjust it to the best viewing angle for you.
Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.
Opening the display
3-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Turning on the power
This section describes how to turn on the power.
After you turn on the power for the first time, do not turn it off until you have
Press and hold the computer's power button for two or three seconds.
Turning on the power
Start up for the first time
When you first turn on the power, the computer's initial screen is the
®
Windows XP Startup Screen Logo. Follow the on-screen directions.
During setup, you can click the Back button to return to the previous
screen.
®
Be sure to read the Windows Operating System End User License
Agreement carefully.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5
Getting Started
Turning off the power
The power can be turned off in one of the following modes: Shut down
(Boot), Hibernation or Standby Mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk.
2. Make sure all disk (disc) activity has stopped, then remove the CD/
DVDs.
Make sure the Built-in HDD/ODD indicators are off. If you turn off the
power while a disk (disc) is being accessed, you can lose data or damage
the disk (disc).
3. Click start and click Turn off Computer. From the Turn off Computer
dialogue box, choose Turn Off.
4. Turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk
when the computer is turned off. The next time the computer is turned on,
the previous state is restored. The hibernation feature does not save the
status of peripheral devices.
1. While entering hibernation mode, the computer saves the contents of
memory to the Hard Disk Drive. Data will be lost if you remove the
battery or disconnect the AC adapter before the save is completed.
Wait for the Built-in Hard Disk Drive indicator to go out.
2. Do not install or remove a memory module while the computer is in
hibernation mode. Data will be lost.
Benefits of Hibernation
The hibernation feature provides the following benefits:
■ Saves data to the hard disk when the computer automatically shuts
down because of a low battery.
3-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
For the computer to shut down in hibernation mode, the hibernation feature
must be enabled in Power Options: Hibernate tab. Otherwise, the
computer will shut down in Standby mode. If battery power becomes
depleted, data saved in Standby will be lost.
■ You can return to your previous working environment immediately when
you turn on the computer.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System
hibernate feature.
■ You can use the panel power off feature.
Starting Hibernation
You can also enable Hibernation by pressing Fn + F4. See Chapter 5, The
Keyboard, for details.
To enter Hibernation mode, follow the steps below.
1. Click start.
2. Select Turn off Computer.
3. Open the Turn off Computer dialog box. If Hibernate is not displayed,
go to step 4. If Hibernate is displayed, go to step 5.
4. Press the Shift key. The Stand By item will change to Hibernate.
5. Select Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.
1. Open the Control Panel.
2. Open Performance and Maintenance and open Power Options.
3. Select the Hibernate tab.
4. Select Enable Hibernation, then click OK button.
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a
moment to save current memory data to the hard disk. During this time, the
Built-in Hard Disk Drive indicator will light.
After you turn off the computer and memory is saved to the hard disk, turn
off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-7
Getting Started
Standby mode
In standby mode the power remains on, but the CPU and all other devices
are in Standby mode.
■ If the computer is not used or accessed in any way, including receipt of
e-mail, for approximately 15 or 30 minutes when the AC adapter is
connected, the computer will automatically enter Standby mode (Power
Options default).
■ To restore operation, press the power button.
■ If the computer automatically enters Standby mode while a network
application is active, the application might not be restored when the
computer wakes up from Standby.
■ To prevent the computer from automatically entering Standby mode,
disable Standby in Power Options. That action, however, will nullify the
computer's Energy Star compliance.
Standby precautions
■ Before entering Standby mode, be sure to save your data.
■ Do not remove/install memory or remove power components:
■ Do not remove/install the memory module. The computer or the
module could be damaged.
■ Do not remove the Battery Pack.
In any of the above cases, the standby configuration will not be saved.
■ If you carry the computer on board an aircraft or into a hospital, be sure
to shut down the computer in hibernation mode or in shutdown mode to
avoid radio signal interference.
Benefits of Standby
The standby feature provides the following benefits:
■ Restores the previous working environment more rapidly than does
hibernation.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System Standby
feature.
■ You can use the panel power off feature.
3-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Enabling Standby
Keyboard, for details.
You can enter standby mode in one of three ways:
1. Click start, click Turn off Computer and click Stand By.
2. Close the display panel. This feature must be enabled. Refer to the
Advanced tab in Power Options described in the Control Panel.
3. Press the power button. This feature must be enabled. Refer to the
Advanced tab in Power Options described in the Control Panel.
When you turn the power back on, you can continue where you left when
you shut down the computer.
■ When the computer is shut down in standby mode, the power indicator
glows amber.
■ If you are operating the computer on battery power, you can lengthen
the operating time by shutting down in hibernation mode. Standby
mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
■ Power is turned back on immediately after shutting down.
■ Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer
Certain conditions require that you reset the system. For example, if:
■ You change certain computer settings.
■ An error occurs and the computer does not respond to your keyboard
commands.
■ There are three ways to reset the computer system:
1. Select Restart from the Turn Off Computer dialogue from StartMenu.
2. Press Ctrl + Alt + Del to display Windows Task Manager, select
Restart from the "Shut down" options.
3. Press the power button and hold it down for five seconds. Once the
computer has turned itself off, wait between ten and fifteen seconds
before turning it on again with the power button.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-9
Getting Started
Create Optical Recovery Discs (depends on the
model you purchased)
A recovery image of your computer is stored on the hard disk. You may use
this image to create CD or DVD recovery discs using the following steps:
1. Select either blank CDs or DVD media.
2. The application will allow you to choose a type of media to create
recovery CDs/DVD including: CD-R, CD-RW, DVD-R, DVD-RW,
DVD+R and DVD+RW.
Some media may not be compatible with the Optical Drive of your
computer. Please verify your Optical Drive supports the blank media you
choose.
3. Turn on your computer to open Windows XP.
4. Insert the (first) blank media into the tray of the Optical Drive.
5. Double Click the Recovery Disc Creator icon on the Windows XP
desktop, or select the application from Start menu.
6. After TOSHIBA Recovery Disc Creator starts, select the type of media
and the title you wish to copy to the media then click the Create button.
If your Optical Drive can only write to CDs, select "CD" as the "Disc Set" on
TOSHIBA Recovery Disc Creator If your Optical Drive of your computer
can write to either CD or DVDs, select the one you are using as the "Disc
Set" on TOSHIBA Recovery Disc Creator.
Restoring the preinstalled software from the
Recovery HDD (depends on the model you purchased)
Part of the space on the hard disk drive is reserved as recovery partition for
restoring the pre-installed software from the hard disk drive.
When re-setting up your hard disk, do not change, delete or add partitions
in a manner other than specified in the manual. Otherwise, space for
software may be destroyed.
In addition, if you use a third-party partitioning program to reconfigure
partitions on your hard disk, it may become impossible to re-setup your
computer.
1. Turn off your computer.
2. Hold down the 0 (zero) key on the keyboard and turn on your computer.
When “In Touch with Tomorrow TOSHIBA” appears, release the 0
(zero) key on the keyboard.
3. A menu appears. Follow the on-screen instructions.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
3-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Restoring the preinstalled software from Recovery
Media
If the preinstalled files are damaged, use the Recovery Media you created,
or the Product Recovery Media, to restore them. To restore the operating
system and all preinstalled software, follow the steps below.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
1. Load the Recovery Media in the optional optical media drive and turn off
the computer's power.
2. Hold down the F12 key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the F12 key.
3. Use the upper or lower cursor key to select the CD/DVD in the display
4. A menu appears. Follow the on-screen instructions.
User’s Manual
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
3-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the
TouchPad, optical media drives, sound system, modem, the wireless LAN
and LAN. It also provides tips on caring for your computer.
Using the TouchPad
To use the TouchPad, simply touch and move your finger tip across it in the
direction you want the on-screen pointer to go.
TouchPad
TouchPad control buttons
TouchPad and TouchPad control buttons
Two buttons below the keyboard are used like the buttons on a mouse
pointer. Press the left button to select a menu item or to manipulate text or
graphics designated by the pointer. Press the right button to display a menu
or other function depending on the software you are using.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1
Operating Basics
Do not press on the TouchPad too hard or press a sharp object such as a
ball point pen against the TouchPad. The TouchPad could be damaged.
For some functions, you can tap the TouchPad instead of pressing a control
button.
Click: Tap the TouchPad once
Double-click: Tap the TouchPad twice
Drag and drop:
1. Hold down the left control button and move the cursor to drag the item
you want to move.
2. Lift your finger to drop the item where you want it.
Scroll:
Vertical: Move your finger up or down the right edge of the TouchPad.
Horizontal: Move your finger left or right along the bottom edge of the
TouchPad.
Using the FingerPrint Reader (depends on model
purchased)
This product has a FingerPrint utility installed for the purpose of enrolling
and recognizing FingerPrints. By enrolling the ID and password to the
FingerPrint authentication device, it is no longer necessary to input the
password from the keyboard. Just by swiping the finger against the
FingerPrint sensor, the following functions will be enabled:
■ Log-on to Windows and access a security-enabled homepage through
IE (Internet Explorer).
■ Files and folders can be encrypted/decrypted and third party access to
them prevented.
■ Disable the password-protected screen-saver when returning from
power-saving mode such as Standby Mode.
■ Power-on Security and Single Sign-On feature.
To "swipe" refers to the action of reading a FingerPrint using the
FingerPrint sensor.
4-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
How the Swipe the Finger
Using the following steps when swiping fingers for FingerPrint registration
or authentication will help to minimize authentication failures:
1. Align the first joint of the finger to the center of the sensor. Lightly touch
the sensor and swipe finger levelly towards you.
While lightly touching the sensor, swipe the finger towards you until the
sensor surface becomes visible.
Ensure the center of the FingerPrint is on the sensor when swiping the
finger.
■ Avoid swiping with the finger stiff or pressed-on too hard
FingerPrint reading may fail if the center of the FingerPrint is not
touching on the sensor, or when finger is swiped while pressing hard.
Make sure that the center of the FingerPrint is touching the sensor
before swiping.
■ Confirm the center of the FingerPrint whirl before swiping
The thumb's FingerPrint has a bigger whirl, which is prone to
misalignment and distortions. This will cause difficulty in registration
and a drop in the authentication success rate. Always confirm the
center of the FingerPrint whirl so that it is swiped along the centerline of
the sensor.
■ When FingerPrint reading is not successful
There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly. Follow the onscreen instructions to adjust the
speed of the swipe.
The following illustrations show the correct way to slide your finger over the
recognition sensor.
Align the finger and sensor like the drawings.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3
Operating Basics
Points to note about the FingerPrint Sensor
Please be aware of the following considerations when using the FingerPrint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, FingerPrint recognition problems or a lower
FingerPrint recognition success rate.
■ Do not scratch or poke the sensor with your nails or any hard or sharp
objects.
■ Do not press the sensor strongly.
■ Do not touch the sensor with a wet finger or any wet objects - keep
sensor surface dry and free of water vapor.
■ Do not touch the sensor with a soiled or dirty finger as minute foreign
particles of dust and dirt may scratch it.
■ Do not paste stickers or write on the sensor
■ Do not touch the sensor with a finger or any other object which may
have a built-up of up static electricity on it.
Observe the following before you place your finger on the sensor whether
for FingerPrint enrollment/registration or recognition.
■ Wash and dry your hands thoroughly.
■ Remove static electricity from your fingers by touching any metal
surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.
■ Clean the sensor with a lint-free cloth - do not use detergent to any
other chemicals to clean the sensor.
■ Avoid the following finger conditions for enrollment or recognition as
they may result in FingerPrint enrollment errors or a drop in the
FingerPrint recognition success rate.
■ Soaked or swollen finger (e.g. after taking bath)
■ Injured finger
■ Wet finger
■ Soiled or oily finger
■ Extremely dry skin condition on finger
Observe the following to improve the FingerPrint recognition success rate.
■ Enroll two or more fingers.
■ Enroll additional fingers if recognition failure occurs when using already
enrolled fingers.
■ Check the condition of your finger - any conditions which have changed
since enrollment, such as injured, rough, extremely dry, wet, soiled,
dirty, oily, soaked, swollen fingers, may lower the recognition success
rate. Also if the FingerPrint is worn down or the finger becomes thinner
or fatter, the recognition success rate may be lowered.
4-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
■ As the FingerPrint for each finger is different and unique, you should
ensure that only the registered or enrolled FingerPrint or FingerPrints
are used for identification.
■ Check the position and speed at which you swipe your finger across the
sensor - please refer to the preceding drawing.
How to Delete the FingerPrint Data
Saved FingerPrint Data is stored in special non-volatile memory inside the
FingerPrint sensor. Therefore, if you give the computer to someone else, or
dispose of it in any way, the following process is recommended to delete
your FingerPrint information:
1. Click start followed by All Programs, followed by Protector Suite QL
and then click Control Center.
2. The Fingerprint Control Center screen is displayed.
3. Click FingerPrints and click Delete.
4. Click Settings and click Fingerprint Storage Inspector.
5. The Fingerprint Storage Inspector screen will be displayed. If
FingerPrint data is displayed as part of the list, simply select all of this
information and then Remove.
6. Check whether all of the FingerPrint data was deleted on the
Fingerprint Storage Inspector screen.
In use, please be aware of the following limitations of the FingerPrint
sensor:
■ The FingerPrint sensor compares and analyzes the unique
characteristics in a FingerPrint.
■ A warning message will be displayed when recognition is abnormal or
recognition is not successful within a fixed duration.
■ The recognition success rate may differ from user to user.
■ TOSHIBA does not guarantee that this FingerPrint recognition
technology will be error-free.
■ TOSHIBA does not guarantee that the FingerPrint sensor will recognize
the enrolled user or accurately screen out unauthorized users at all
times. TOSHIBA is not liable for any failure or damage that might arise
out of the use of this FingerPrint recognition software or utility.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5
Operating Basics
Points to note about the FingerPrint Utility software
You are able to backup saved FingerPrint data and information within the
PasswordBank by using the import or Export User Data facility under the
FingerPrint management software. However, please be aware that any
encrypted files cannot be backup within FileSafe using this function - in
these instances it is recommended that you backup these files to external
media using standard file copy processes.
The user should back up the user profile information when using the
functions provided in this software to encrypt files or folders. If this software
or the user information is deleted without backing up the user profile
information, the encrypted files will no longer be accessible. In addition, if
the backup data is not used, the user will not be identified as the same user
even if the same name is used again in user enrolment.
Please refer to the following procedures to back up.
If Windows XP’s file encryption function EFS (Encryption File System) is
used to encrypt a file, the file cannot be further encrypted using the
encryption function of this software. In the help file, it is stated that this
software's Password Bank function can be used for the Internet and
general applications. However, the Internet Password Bank function in the
FingerPrint utility provided in this computer can only be used with IE
(Internet Explorer).
Set up Procedure
Please use the following procedure when first using Fingerprint
authentication.
FingerPrint Registration
You should initially enroll the required authentication data using the ‘User
Enrollment’ Wizard.
■ In use, the FingerPrint authentication system will use the same
username and password as defined within Windows operating system.
If no Windows password has been configured, you must do this before
starting the FingerPrint registration process.
■ Up to twenty-one FingerPrint patterns can be registered on this sensor.
1. Click start followed by All Programs followed by Protector Suite QL
and then click User Enrollment.
You are also able to start the User Enrollment Wizard by using the
following method.
■ Click the Protector Suite QL icon in the Task Bar.
■ Swipe your finger across the FingerPrint Sensor.
2. Click Next.
4-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
3. At the User’s Password screen which is then displayed, you should
ensure that the same Windows username is displayed before entering
the appropriate password into the Enter password field. Once this has
been done, click Next.
4. At the Hints for Fingerprint Enrollment screen, confirm the message
displayed and ensure that there is a check mark in the Run interactive
tutorial box. Once this has been done, click Next.
5. At the Correct Swipe Procedure screen, confirm the message that is
diplayed and then click Next.
6. At the Scanning Practice screen, you are able to practice swiping your
finger to ensure you use the correct method. Once you have finished
practicing, click Next.
7. At the User’s Fingers screen, select the finger you wish to enroll from
the illustration and then click Next. On this screen please be aware that
any previously enrolled FingerPrints would have green check marks,
while the FingerPrint you are about to enroll will have a red check mark.
If any of the previously enrolled FingerPrints is selected again, the latest
information will be enrolled and any previous information over-written.
8. At Advanced Security screen, select whether you wish tto enable the
security function, and then click Next.
9. At Finalization screen, click Finish - this will complete the FingerPrint
registration process.
Window Log-on via FingerPrint Authentication
If required, you are also able to use FingerPrint authentication in place of
the usual Windows log-on process using your username and password.
This method is specially useful where there are many users using the same
computer as it removes the need for actual user selection when the system
is started.
FingerPrint Authentication Procedure
1. Start up the computer.
2. At the Log-on Authorization screen, choose any of the enrolled
fingers and swipe the FingerPrint on the sensor - If the authentication
process is successful, the user will automatically be logged into
Windows.
If the FingerPrint authentication process fails you will need to log into
Windows using the appropriate username and password. In addition, you
should use this manual login process if Finger Print authentication fails for
three consecutive tries - a warning message will be displayed when
authentication is not normal or is not successful within a fixed duration.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-7
Operating Basics
FingerPrint Power-on Security
General
The FingerPrint authentication system can be used to replace the keyboard
based password authentication system that is used when the computer is
turned on.
If you do not want to use the FingerPrint authentication system for
password authentication when the computer is turned on, but instead prefer
to use the keyboard entry method instead, simply press the BkSP
(backspace) key or the ESC/Rotation button when the FingerPrint Power-
on Security screen is displayed. Using this process will switch the
password input screen across to the keyboard based entry screen.
■ You must ensure that you use the TOSHIBA Password Utility to
register a User Password before using the FingerPrint Power-on
Security and its extended function to allow FingerPrint to be used to
access the computer when it is turned on.
■ If the FingerPrint authentication process fails five times, a preset time
limit is exceeded, or you press the BkSP (backspace) key, [Password=]
will be displayed on the screen and you will have to enter either the
User Password or Supervosor Password manually in order to start the
computer.
■ When swipe your finger, please ensure you do it slowly and at a
constant speed. If you find that this does not improve the authentication
rate, you should try to adjust the speed at which the finger is swiped.
■ If there are any changes in the environment or setting related to
authorization, you will be required to provide authorization information
such as a User Password (and, if applicable, the HDD (Hard Disk
Drive) password).
How to Enable FingerPrint Power-on Security Settings
It is necessary to first enroll your FingerPrint with the Protector Suite QL
application prior to enabling and configuring the FingerPrint Power-on
Security System. You should check that your FingerPrint is enrolled before
configuring the settings (please refer to the Manual for FingerPrint
Registration/Enrollment for further instructions.)
1. Swipe your finger across the FingerPrint Sensor.
2. MENU will appear in the place where your mouse is. Swipe(*) your
finger on the FingerPrint sensor and then select Control Center from
the items presented in this menu.
(*) It is recommended that the keyboard cursor keys (movement) and enter
key (selection) or the directional pad be used when selecting and item from
the Menu in laptop or landscape modes.
4-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
3. At the Fingerprint Control Center screen, click Settings and then
click System Settings.
4. At the Protector Suite Settings screen, place a check mark in the
Allow power-on security single sign-on and then click OK.
FingerPrint Single Sign-On Feature
General
This is a feature that allows the user to complete the authentication for both
the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive)
Password) and logging onto Windows using only one FingerPrint
authentication when booting up. It is necessary to register the User/BIOS
Password and Windows Log-on password before using the FingerPrint
Power-on Security and this FingerPrint Single Sign On Feature. Please use
TOSHIBA Password Utility to register your User/BIOS Password. If
Windows Log-on is not the default for your system, see Manual to register
your Windows Log-on password.
Only one FingerPrint authentication is required to replace the User/BIOS
Password (and, if applicable, the HDD (Hard Disk Drive) Password) and
Windows Log-on Password.
How to Enable FingerPrint Single Sign-On Feature
It is necessary to first enroll your FingerPrint with the Protector Suite QL
application prior to enabling and configuring the FingerPrint Single Sign-
On Feature. You should check that your FingerPrint is enrolled before
configuring the settings (please refer to the Manual for FingerPrint
Registration/Enrollment for furthe instructions).
1. Swipe your finger across the FingerPrint Sensor.
2. MENU will appear in the place where your mouse is. Swipe(*) your
finger on the FingerPrint Sensor and select Control Center from the
items presented in this menu.
(*) It is recommended that the keyboard cursor keys (movement) and enter
key (selection) or the directional pad be used when selecting and item from
the Menu in laptop or landscape modes.
3. At the Fingerprint Control Center screen, click Settings and then
click System Settings.
4. At the Protector Suite Settings screen, place a check mark in the
Allow power-on security single sign-on and then click OK.
FingerPrint utility limitations
TOSHIBA does not guarantee that the FingerPrint utility technology will be
completely secure or error-free or it will be accurately screen out
unauthorized users at all times. TOSHIBA is not liable for any failure or
damage that might arise out of the use of the FingerPrint software.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-9
Operating Basics
Using the Web Camera (depends on the model
purchased)
This section describes the bundled webcam utility, which can capture still
and video images. The web camera will auto-run when Windows starts.
Web Camera Lens *
Web Camera LED *
Built-in microphone *
* Depends on the model purchased
Using the software
The web camera software is pre-configured to start when you turn on
Windows XP; if you need to restart it go to start ꢀ All Programs ꢀ
Camera Assistant Software ꢀ Camera Assistant Software.
Capture Still
Images
Video
Recording
Audio
Recording
Function
Display Window
Camera resolution
Effects
Mute
4-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Capture Still Images Click to see a preview of the captured image; you
can also e-mail the image.
Video Recording
Click to prepare for recording. Click again to start
recording. One more to stop recording and see
preview of the video.
Audio Recording
Function
Click to start recording, click again to stop and
listen to a preview of the audio.
Access additional functions: About, Player,
Effects, Properties, Settings and Help.
About
Player
Effects
Displays software manufacturer details.
Play video files.
Choose images to be displayed on the capture
screen.
Properties
Choose from the Options tab to flip, zoom,
flicker rate, night mode and backlight
compensation; in the Image tab change the color
settings; in the Profiles tab change the lighting
conditions.
Settings
Choose from the: Options tab to change the tool
bar position; the Picture tab to select picture
output options such as size, export file and save
path; the Video tab to choose video output
settings such as Frame Rate, Size, Compression
and the frame rate, size, record compressor, and
save path; the Audio tab to change the audio
device, audio compressor, audio volume and
save path.
Help
Displays the help files for the software.
Using the microphone
Your computer has a built-in microphone that can be used to record
monaural sounds into your applications. It can also be used to issue voice
commands to applications that support such functions.(Built-in microphone
is provided with some models)
Since your computer has a built-in microphone and speaker, “feedback”
may be heard under certain conditions. Feedback occurs when sound from
the speaker is picked up in the microphone and amplified back to the
speaker, which amplifies it again to the microphone.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-11
Operating Basics
This feedback occurs repeatedly and causes a very loud, high-pitched
noise. It is a common phenomenon that occurs in any sound system when
the microphone input is output to the speaker (throughput) and the speaker
volume is too loud or too close to the microphone. You can control
throughput by adjusting the volume of your speaker or through the Mute
function in the Master Volume panel. Refer to your Windows documentation
for details on using the Master Volume panel.
Using the optical media drive
The text and illustrations in this section refer primarily to the optical CD-
ROM drive. However, operation is the same for all other optical media
drives. The full-size drive provides high-performance execution of CD-
ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15")
CDs without an adaptor. An ATAPI interface controller is used for CD-ROM
operation. When the computer is accessing a CD-ROM, an indicator on the
drive glows.
If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs with
precautions on writing to CDs/DVDs.
Loading discs
To load a disc, follow the steps below and refer to the figures.
1. a. When the power is on, press the eject button to open the drawer
slightly.
Eject Button
Pressing the eject button
4-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
b. Pressing the eject button will not open the drawer when the disc
drive's power is off. If the power is off, you can open the drawer by
inserting a slender object (about 15 mm) such as a straightened
paper clip into the eject hole just to the right of the eject button.
Manual release with the eject hole
2. Grasp the drawer gently and pull until it is fully opened.
Pulling the drawer open
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-13
Operating Basics
3. Place the disc, label side up, in the drawer.
Inserting a disc
When the drawer is fully opened, the edge of the computer will extend
slightly over the disc tray. Therefore, you will need to turn the disc at an
angle when you place it in the tray. After seating the disc, however, make
sure it lies flat, as shown in the figure above.
■ Do not touch the laser lens. Doing so could cause misalignment.
■ Keep foreign matter from entering the drive. Check the back edge of
the tray to make sure it carries no debris before closing the drive.
4. Press gently at the centre of the disc until you feel it click into place. The
disc should lie below the top of the spindle, flush with the spindle base.
5. Push the center of the drawer to close it. Press gently until it locks into
place.
If the disc is not seated properly when the drawer is closed, the disc might
be damaged. Also, the drawer might not open fully when you press the
eject button.
4-14
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Closing the disc drawer
Removing discs
To remove the disc, follow the steps below and refer to the figure.
Do not press the eject button while the computer is accessing the disc
drive. Wait for the optical media drive indicator to go out before you open
the drawer. Also, if the disc is spinning when you open the drawer, wait for
it to stop before you remove it.
1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.
■ When the drawer pops open slightly, wait a moment to make sure the
disc has stopped spinning before pulling the drawer fully open.
■ Turn off the power before you use the eject hole. If the disc is spinning
when you open the drawer, the disc could fly off the spindle and cause
injury.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-15
Operating Basics
2. The disc extends slightly over the sides of the drawer so you can hold it.
Hold the disc gently by its edges and lift it out.
Removing a disc
3. Push the centre of the drawer to close it. Press gently until it locks into
place.
Writing CD/DVDs with the DVD Super Multi drive
supporting DVD±R Double layer
Some models in this series are equipped with Writing CD/DVDs with the
DVD Super Multi drive (Supporting DVD±R Double Layer).
You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
preinstalled: TOSHIBA Disc Creator and TOSHIBA Direct Disc Writer.
Important message (DVD Super Multi drive supporting
DVD±R Double layer)
Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
discs, read and follow all setup and operating instructions in this section. If
you fail to do so, the DVD Super Multi drive may not function properly, and
you may fail to write or rewrite, lose data or incur other damage.
4-16
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Before writing or rewriting
■ Based on TOSHIBA's limited compatibility testing, we suggest the
following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
discs. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.
CD-R: TAIYO YUDEN Co., Ltd.
MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.
Hitachi Maxell Ltd.
CD-RW: MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.
High Speed CD-RW: MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.
Ultra Speed CD-RW: MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD-R: DVD Specifications for Recordable disc for
General Version2.0
TAIYO YUDEN Co., Ltd.
Matsushita Electric Industrial Co., Ltd.
DVD-R(DL): MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD+R: MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.
DVD+R(DL): MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD-RW: DVD Specifications for Recordable Disc for
Version 1.1 or 1.2
Victor Company of Japan, Ltd. (JVC)
MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD+RW: MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD-RAM: DVD Specifications for DVD-RAM Disc for
Version2.0, 2.1 or 2.2
Hitachi Maxell Ltd.
Matsushita Electric Industrial Co., Ltd.
This drive cannot use discs that allow writing of 8 speeds or more (DVD-R,
DVD+R, DVD+RW ), or 6 speeds or more (DVD-RW)
■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors
may occur. Be careful to check the disc for dirt or damage before you
use it.
■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or
DVD-RAM is affected by the quality of the disc and the way it is used.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-17
Operating Basics
■ There are two types of DVD-R discs: authoring and general use discs.
Do not use authoring discs. Only general use discs can be written to by
a computer drive.
■ We can support only Format1 of DVD-R DL. Therefore you cannot do
the additional writing. If your data is under 4.7GB, we suggest to use
DVD-R (SL) media.
■ You can use DVD-RAM discs that can be removed from a cartridge and
DVD-RAM discs designed without a cartridge. You can not use a disc
with a 2.6GB single-sided capacity and 5.2GB double-sided capacity.
■ Other DVD-ROM drives for computers or other DVD players may not be
able to read DVD-R/-RW or DVD+R/+RW discs.
■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in
whole or in part.
■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and
DVD-RAM disc cannot be recovered. Check the content of the disc
carefully before you delete it. If multiple drives that can write data to
discs are connected, be careful not to delete data from the wrong drive.
■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc
space is required for file management, so you may not be able to write
the full capacity of the disc.
■ Since the disc is based on the DVD standard, it might be filled with
dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.
®
■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000
without DVD-RAM Driver Software.
■ When multiple drives that can write data to discs are connected, be
careful not to write to the wrong drive.
■ Be sure to connect the AC adaptor before you write or rewrite.
■ Before you enter Standby Mode/Hibernation Mode, be sure to finish
DVD-RAM writing. Writing is finished if you can eject DVD-RAM media.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver, which can put a heavy load
on the CPU.
■ Operate the computer under the power scheme High Performance. Do
not use power-saving features.
■ Do not write while virus check software is running. Wait for it to finish
and then disable virus detection programs including any software that
checks files automatically in the background.
■ Do not use hard disc utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
■ Write from the computer's hard disc drive to the CD/DVD. Do not try to
write from shared devices such as a LAN server or any other network
device.
■ Writing with software other than TOSHIBA Disc Creator is not
recommended.
4-18
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
When writing or rewriting
Please observe/consider the following when you write or rewrite to a CD-R/
-RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.
■ Do not perform any of the following actions when writing or rewriting:
®
■ Change users in the Windows XP operating system.
■ Operate the computer for any other function, including using a
mouse or TouchPad or closing/opening the LCD panel.
■ Start a communication application such as a modem.
■ Apply impact or vibration to the computer.
■ Install, remove or connect external devices, including the following:
PC Card, USB devices, external display, optical digital devices.
■ Use the audio/video control buttons to reproduce music or voice.
■ Open the DVD Super Multi drive.
■ Do not use shut down/log off and Standby Mode/Hibernation Mode
while writing or rewriting.
■ Make sure writing or rewriting is completed before going into Standby
Mode/Hibernation Mode. Writing is completed if you can open the DVD
Super Multi drive tray.
■ Set the computer on a level surface and avoid places subject to
vibration such as airplanes, trains, or cars. Do not use an unstable
surface such as a stand.
■ Keep mobile phones and other wireless communication devices away
from the computer.
■ Always copy data from the hard disk drive to the CD-R/-RW,DVD-R/-
RW/-RAM or DVD+R/+RW disc. Do not use cut-and-paste. The original
data will be lost if there is a write error.
Disclaimer (DVD Super Multi drive supporting DVD±R Double
layer)
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may
be caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/
-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with
this product, or for any business profit loss or business interruption that
may be caused by the change or loss of the recorded contents.
■ Damage that may be caused by using third party equipment or
software. Given the technological limitations of current optical disc
writing drives, you may experience unexpected writing or rewriting
errors due to disc quality or problems with hardware devices. Also, it is
a good idea to make two or more copies of important data, in case of
undesired change or loss of the recorded contents.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-19
Operating Basics
TOSHIBA Disc Creator
Note the following limitations when you use TOSHIBA Disc Creator:
■ DVD-Video cannot be created using TOSHIBA Disc Creator.
■ DVD-Audio cannot be created using TOSHIBA Disc Creator.
■ You cannot use the TOSHIBA Disc Creator "Audio CD" function to
record music to the DVD-R/-RW or DVD+R/+RW media.
■ Do not use the "Disc Backup" function of TOSHIBA Disc Creator to
copy
■ DVD-Video and DVD-ROM with copyright protection. DVD-RAM media
cannot be backed up with the "Disc Backup" function of TOSHIBA Disc
Creator.
■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/
+RW using the "Disc Backup" function of TOSHIBA Disc Creator.
■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/
+RW to CD-R/RW using TOSHIBA Disc Creator.
■ TOSHIBA Disc Creator cannot record in packet format.
■ You might not be able to use the Disc Backup function of TOSHIBA
Disc Creator to backup a DVD-R/-RW or DVD+R/+RW disc that
wasmade with other software on a different DVD-R/-RW or DVD+R/
+RW recorder.
■ If you add data to a DVD-R and DVD+R disc that you have already
recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows ME, in Windows NT4 you will need
Service Pack 6 or later to read the data, and in Windows 2000 you will
need Service Pack 2 or later to read it. Some optical media drives
cannot read added data regardless of the operating system.
■ TOSHIBA Disc Creator does not support recording to DVD-RAM discs.
To record to a DVD-RAM, use Explorer or other similar utility.
■ When you back up a DVD disc, be sure the source drive supports
recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs, it
might not be backed up correctly.
■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to
use the same type of disc.
■ You cannot partially delete any data written to a CD-RW, DVD-RW or
DVD+RW disc.
4-20
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Data Verification
To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.
1. Display the setting dialog box by one of the following two steps:
■ Click the setting button ( ) for writing on the main toolbar in the
Data Disc mode.
■ In the Settings menu, select Settings for Each Mode, then Data
Disc.
2. Mark the Verify Written Data check box.
3. Select File Open or Full Compare mode.
4. Click the OK button.
Media care
This section provides tips on protecting data stored on your CD/DVDs.
Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them:
CD/DVDs
1. Store your CD/DVDs in the container they came in to protect them and
keep them clean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the centre hole.
Fingerprints on the surface can prevent the drive from properly reading
data.
5. Do not expose to direct sunlight, extreme heat or cold. Do not place
heavy objects on your CD/DVDs.
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry
cloth. Wipe from the centre out, do not wipe in a circular direction
around the CD/DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-21
Operating Basics
Modem (depends on the model purchased)
This section describes how to connect and disconnect the internal modem
to and from a telephone jack.
The internal modem does not support voice functions. All data and fax
functions are supported.
■ In case of a lightning storm, unplug the modem cable from the
telephone jack.
■ Do not connect the modem to a digital telephone line. A digital line will
damage the modem.
Region selection
Telecommunication regulations vary from one region to another, so you will
need to make sure the internal modem's settings are correct for the region
in which it will be used.
To select a region, follow the steps below.
1. Click start, point to All Programs, TOSHIBA, Networking, and click
Modem Region Select.
Do not use the Country/Region Select function in the Modem setup utility
in the Control Panel if the function is available. If you change the Country/
Region in the Control Panel, the change may not take effect.
2. The Region Selection icon will appear in the Task Bar. Click the icon
with the primary mouse button to display a list of regions that the
modem supports. A sub menu for telephony location information will
also be displayed. A check will appear next to the currently selected
region and telephony location.
3. Select a region from the region menu or a telephony location from the
sub-menu.
■ When you click a region it becomes the modem's region selection,
and the New Location for telephony will be set automatically.
■ When you select a telephony location, the corresponding region is
automatically selected and it becomes the modem's current region
setting.
Properties menu
Click the icon with the secondary mouse button to display properties menu
on the screen.
4-22
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Settings
You can enable or disable the following settings:
AutoRun Mode
The Region Select utility starts automatically when you start up the
operating system.
Open the Dialling Properties dialog box after selecting
region.
The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current
Location region code do not match.
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is
displayed. Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
If you are using the computer in Japan, the Telecommunications Business
Law requires that you select Japan region mode. It is illegal to use the
modem in Japan with any other selection.
Connecting
To connect the modem cable, follow the steps below.
■ The modular cable that comes with the computer must be used to
connect a modem. Connect the end of the modular cable with the core
to the computer.
■ In case of a lightning storm, unplug the modem cable from the
telephone jack.
■ Do not connect the modem to a digital telephone line. A digital line will
damage the modem.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-23
Operating Basics
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack.
Connecting the internal modem
Do not pull on the cable or move the computer while the cable is
connected.
If you use a storage device such as an optical drive or hard disk drive
connected to a 16-bit PC Card, you might experience the following modem
problems:
■ Modem speed is slow or communication is interrupted.
■ Skips may occur in sound.
Disconnecting
To disconnect the internal modem cable, follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. In the same way, pull the cable’s other connector out of the computer.
4-24
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Wireless communications
The computer’s wireless communication function supports both Wireless
LAN and Bluetooth devices.
Only some models are equipped with both Wireless LAN and Bluetooth
functions.
■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a
microwave oven or in areas subject to radio interference or magnetic
fields. Interference from a microwave oven or other source can disrupt
Wi-Fi or Bluetooth operation.
■ Turn Wi-Fi and Bluetooth functionalities off when near a person who
may have a cardiac pacemaker implant or other medical electric
device. Radio waves may affect pacemaker or medical device
operation, possibly resulting in serious injury. Follow the instruction of
your medical device when using any Wi-Fi or Bluetooth functionality.
■ Always turn off Wi-Fi or Bluetooth functionality if the computer is near
automatic control equipment or appliances such as automatic doors or
fire detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.
■ It may not be possible to make a network connection to a specified
network name using the ad hoc network function.
If this occurs, the new network(*) will have to be configured for all
computers connected to the same network in order to re-enable
network connections.
* Please be sure to use new network name.
Wireless LAN
The Wireless LAN feature is not available on all models. Where present, it
supports the A,B, G and N standards but it is compatible with other LAN
systems based on Direct Sequence Spread Spectrum/Orthogonal
Frequency Division Multiplexing radio technology that complies with
IEEE802.11 Wireless LAN standard.
■ Automatic Transmit Rate Select mechanism in the transmit range of 54,
48, 36, 24, 18, 12, 9 and 6 Mbit/s. (IEEE 802.11g)
■ Automatic Transmit Rate Select mechanism in the transmit range of 11,
5.5, 2 and 1 Mbit/s. (IEEE 802.11b)
■ Roaming over multiple channels
■ Card Power Management
■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit
encryption algorithm.
■ Advanced Encryption Standard (AES) data encryption, based on 128 bit
encryption algorithm.
Wake-up on LAN does not function on a Wireless LAN.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-25
Operating Basics
Security
■
Be sure to enable the encryption function otherwise you may expose
your computer to illegal access by an outsider across the Wireless LAN
which may cause intrusion, eavesdropping, and the loss or destruction
of stored data. TOSHIBA strongly recommend the customer to enable
the encryption function.
■ TOSHIBA is not liable for the eavesdropping of data due to the use of
Wireless LAN and the damage thereof.
®
®
Bluetooth Stack for Windows by TOSHIBA (depends on the
model purchased)
Please note that this software is specifically designed for the following
operating systems:
®
■ Microsoft Windows XP
Detailed information regarding the use with these operating systems is
listed below. Please refer also to the electronic information which is
included with each software.
®
®
This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR
specification. TOSHIBA cannot confirm compatibility between any PC
®
products and/or other electronic devices that use Bluetooth other than
TOSHIBA notebook computers.
®
Release Notes related to the Bluetooth Stack for
®
Windows by TOSHIBA
1. Fax application software:
Regarding FAX application software, there are some software that you
®
cannot use on this Bluetooth Stack.
2. Multi User:
On Windows XP, the use of Bluetooth is not supported in a multi-user
environment. This means that, when you use Bluetooth, other users
logged onto the same computer will not be able to use its Bluetooth
functionality.
Product Support:
The latest information regarding Operating System support, Language
Support or available upgrades can be found on our web site http://
www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or
www.pcsupport.toshiba.com in the United States.
4-26
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Wireless communication switch
You can enable or disable the Wireless LAN function, with the on/off switch.
No transmissions are sent or received when the switch is off. Slid the
Switch to turn it on and turn it off.
Set the switch to off in airplanes and hospitals. Check the indicator. It will
stop glowing when the wireless communication function is off.
Wireless communication indicator
The wireless communication indicator indicates the status of the wireless
communication functions.
Indicator status
Indication
Indicator off
Wireless communication switch is set to off.
Automatic power down because of overheating.
Power malfunction
Indicator glows
Wireless communication switch is on. Wireless
LAN is turned on by an application.
If you used the Task Bar to disable Wireless LAN, you will need to restart
the computer to re-enable it. Alternatively, you can also follow this
procedure:
1. In the Control Panel, click Performance and Maintenance, then
System.
2. Select the Hardware tab.
3. Click the Device Manager. The Device Manager window opens. Click
Network adaptors.
4. Select your preferred Network adaptor, then click the Enable button in
the tool bar.
LAN
The computer has built-in support for Ethernet LAN (10 megabits per
second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second,
100BASE-TX). This section describes how to connect/disconnect to a LAN.
LAN cable types
The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer's default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.
User’s Manual
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable or higher. You cannot
use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect with a CAT3 cable or higher.
Connecting LAN cable
To connect the LAN cable, follow the steps below.
1. Turn off the power to the computer and to all external devices
connected to the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.
Connecting the LAN cable
3. Plug the other end of the cable into a LAN hub connector. Check with
your LAN administrator before connecting to a hub.
Disconnecting LAN cable
To disconnect the LAN cable, follow the steps below.
1. Pinch the lever on the connector in the computer's LAN jack and pull
out the connector.
2. Disconnect the cable from the LAN hub in the same manner. Check
with your LAN administrator before disconnecting from the hub.
4-28
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Cleaning the computer
To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.
■ Be careful not to spill liquids into the computer. If the computer does get
wet, turn the power off immediately and let the computer dry completely
before you turn it on again.
■ Clean the computer using a slightly damp (with water) cloth. You can
use glass cleaner on the display. Spray a small amount of cleaner on a
soft, clean cloth and wipe the screen gently with the cloth.
Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.
■ Remove the dust from the cooling vents on the Left side of the
computer regularly with a vacuum cleaner. Refer to Chapter 2, The
Moving the computer
The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.
■ Before moving the computer, it recommends changing the function of
TOSHIBA HDD Protection. Refer to the section, Using the Hard Disk
Drive (HDD) Protection, in this chapter.
■ Make sure all disk activity has ended before moving the computer.
Check the HDD indicator on the computer.
■ If a CD/DVD is in the drives, remove it. Also make sure the disc tray is
securely closed.
■ Turn off (shut down) the computer.
■ Disconnect the AC adaptor and all peripherals before moving the
computer.
■ Close the LCD display panel. Do not pick up the computer by its display
panel.
■ Before carrying your computer, shut down the computer, disconnect the
power cable and wait until the PC cools down. Failure to follow this
instruction could result in minor injury.
■ Always turn off the power when you move the computer. If the power
button has a lock, set it to the lock position. Also be careful not to
subject the computer to impact. Failure to follow this instruction could
result in damage to computer, computer failure or loss of data.
■ Never transport your computer with PC cards installed. This could
cause damage to your computer and/or PC card, resulting in product
failure.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-29
Operating Basics
■ Use the carrying case when transporting the computer.
■ When carrying your computer, be sure to hold it securely so that it does
not fall or hit anything.
■ Do not carry your computer by holding protruded portions.
Using the Hard Disk Drive (HDD) Protection
This computer has a function for reducing the risk of damage on the hard
disk drive.
Using an acceleration sensor built into the computer, TOSHIBA HDD
Protection detects vibration shocks and similar signs of movement of the
computer, and automatically moves the Hard Disk Drive head to a safe
position to reduce the risk of damage that could be caused by head-to-disk
contact.
This function does not guarantee that the hard disk drive will not be
damaged.
When vibration is detected, a message will be displayed on the screen, and
the icon in the taskbar notification area will change to the protection state.
This message is displayed until the OK button is pressed or 30 seconds
pass. When vibration subsides, the icon returns to the normal state.
Taskbar Icon
State
Icon
Description
Normal
TOSHIBA HDD Protection is enabled.
Protection
OFF
TOSHIBA HDD Protection is active.
The hard disk drive head is in a safe
position.
TOSHIBA HDD Protection is disabled.
TOSHIBA HDD Protection Properties
You can change the TOSHIBA HDD Protection settings by using the
TOSHIBA HDD Protection Properties window. To open the window, click
start Æ All Programs Æ TOSHIBA Æ Utilities Æ HDD Protection
Setting. The window can also be started from the icon on the Taskbar or
from the Control Panel.
HDD Protection
You can choose whether to enable or disable TOSHIBA HDD Protection.
4-30
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Basics
Detection Level
This function can be set to four levels. The sensitivity levels in which
vibrations, impacts and their similar signs are detected can be set to OFF,
1, 2 and 3 in ascending order. Level 3 is recommended for better protection
of the computer. However, when the computer is used in a mobile
environment or in other unstable conditions, setting the detection level to 3
could result in frequent execution of TOSHIBA HDD Protection, which will
slow Hard Disk Drive reading and writing. Set a lower detection level when
the speed of Hard Disk Drive reading and writing is a priority.
Different detection levels can be set depending on whether the computer is
used as handheld or mobile usages, or whether it is used in a stable
environment such as on a table in the workplace or at home. By setting
different detection levels for the computer depending on whether it runs
with the AC power (desktop) or with batteries (handheld or mobile usage),
the detection level automatically switches according to the power
connection mode.
3D Viewer
This feature displays a 3D object on the screen which moves in according
to tilting or vibration of the computer.
When the TOSHIBA HDD Protection detects computer vibration the Hard
Disk Drive head is parked and the 3D object disk rotation will stop. When
the head is un-parked the disk will begin to rotate again.
The 3D Viewer can be started from the icon in the task tray.
■ This 3D object virtually represents the Computer's internal Hard Disk
Drive. This representation may vary from the actual number of disks,
disk rotation, head movement, part size, shape and direction.
■ This feature may use a large amount of CPU and memory on some
models. The computer may become slow or sluggish when attempting
to run other applications while the 3D Viewer is displayed.
■ Intensely shaking the computer or other subjecting it to strong impacts
may cause damage to the computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-31
Operating Basics
Details
To open the Details window, click the Setup Detail button in the TOSHIBA
HDD Protection Properties window.
Detection Level Amplification
When the AC adaptor is disconnected or the lid is closed, HDD Detection
assumes that the computer will be carried and sets the detection level to
the maximum for 10 seconds.
TOSHIBA HDD Protection Message
Specify whether to display a message when TOSHIBA HDD Protection is
active.
■ This function does not work when the computer is starting, in Standby
Mode, in Hibernation Mode, in transition to Hibernation Mode,
recovering from Hibernation Mode, or powered off. Be sure to not
subject the computer to vibration or impact while the function is
disabled.
■ This function only operates with Windows XP.
4-32
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 5
The Keyboard
The computer's keyboard layouts are compatible with a 101/102-key
enhanced keyboard. By pressing some keys in combination, all the 101/
102-key keyboard functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region’s
keyboard layout your computer is configured with. Keyboards for numerous
languages are available.
There are six types of keys: typewriter keys, keypad overlay, function keys,
®
soft keys, Windows special keys, and cursor control keys.
Typewriter keys
The typewriter keys produce the upper- and lower-case letters, numbers,
punctuation marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and
using a computer keyboard:
■ Letters and numbers produced in computer text vary in width. Spaces,
which are created by a "space character," may also vary depending on
line justification and other factors.
■ The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
■ The uppercase O (oh) and the 0 (zero) are not interchangeable.
■ The Caps Lock function key locks only the alphabetic characters in
uppercase while the shift lock on a typewriter places all keys in the
shifted position.
■ The Shift keys, the Tab key, and the BackSpace key perform the same
function as their typewriter counterparts but also have special computer
functions.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-1
The Keyboard
F1 ... F12 function keys
The function keys (not to be confused with Fn) are the 12 keys at the top of
your keyboard. These keys function differently from other keys.
F1 through F12 are called function keys because they execute
programmed functions when pressed. Used in combination with the Fn key,
keys marked with icons execute specific functions on the computer. Refer
executed by individual keys depends on the software you are using.
Soft keys: Fn key combinations
The Fn (function) is used in combination with other keys to form soft keys.
Soft keys are key combinations that enable, disable or configure specific
features.
Some software may disable or interfere with soft-key operations. Soft-key
settings are not restored by the Standby Mode feature.
Emulating keys on enhanced keyboard
A 101-key enhanced keyboard layout
The keyboard is designed to provide all the features of the 101-key
enhanced keyboard, shown in figure above. The 101/102-key enhanced
keyboard has a numeric keypad and scroll lock key. It also has additional
Enter and Ctrl keys to the right of the main keyboard. Since the keyboard
is smaller and has fewer keys, some of the enhanced keyboard functions
must be simulated using two keys instead of one on the larger keyboard.
Your software may require you to use keys that the keyboard does not
have. Pressing the Fn key and one of the following keys simulates the
enhanced keyboard's functions.
5-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Keyboard
Press Fn + F11 to access the integrated keypad. When activated, the keys
with gray markings on the bottom edge become numeric keypad keys.
how to operate these keys. The power on default for both settings is off.
Press Fn + F12 to lock the cursor on a specific line. The power on default is
off.
Hot keys
+
Mute:Turns the volume on and off.
+
Lock: Enters "Lock computer" mode. To restor your desktop, you need to
log on again.
+
Power plan: Displays the power save modes and lets you change the
power settings.
+
Standby: This hot key switches the system to Standby Mode.
+
Hibernate:This hot key switches the system to Hibernate mode.
+
Output: Changes the active display device.
Default resolution for simultaneous mode is set to 1024x768. If you
connect an RGB (Monitor) that is not 1024x768 resolution, change it in
"Display Properties".
User’s Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Keyboard
+
Brightness (decreases): Turns the monitor brightness down.
+
Brightness (increases): Turns the monitor brightness up.
+
Wireless: Switches the active wireless devices if the wireless
communication switch is switched on.
+
TouchPad: Enables or disables the Touch Pad function.
+
Enable Keypad: Enables or disables the Key Pad function.
+
Number Lock: Enables or disables the Number Lock function.
+
Scroll Lock: Enables or disables the Scroll Lock function.
+
Zoom: Changes the display resolution.
+
TOSHIBA Zooming Utility (reduce): Reduces the icon size on the
desktop or the font size within one of the supported application windows.
5-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Keyboard
+
TOSHIBA Zooming Utility (enlarge): Increases the icon size on the
desktop or the font size within one of the supported application windows.
Before using Fn+1 and Fn+2, you must install the TOSHIBA Zooming
Utility. The Utility only supports the following application windows:
Microsoft Internet Explorer, Microsoft Office, Windows Media Player,
Adobe Reader and the icons on the desktop.
Fn Sticky key (Depends on the model you purchased)
You can use the TOSHIBA Accessibility Utility to make the Fn key sticky,
that is, you can press it once, release it, and then press an "F number" key.
To start the TOSHIBA Accessibility Utility, click start, point to All
Programs, point to TOSHIBA, point to Utilities and click Accessibility.
®
Windows special keys
®
The keyboard provides two keys that have special functions in Windows
:
®
Windows logo key activates the start menu and the other, the application
key, has the same function as the secondary mouse button.
®
This key activates the Windows start menu.
This key has the same function as the secondary mouse button.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-5
The Keyboard
Keypad overlay
Your computer's keyboard does not have an independent numeric keypad,
but its numeric keypad overlay functions like one.
The keys in the centre of the keyboard with gray letters make up the
numeric keypad overlay. The overlay provides the same functions as the
numeric keypad on the 101/102-key enhanced keyboard described
previously.
Turning on the overlays
The numeric keypad overlay can be used for numeric data input.
Numeric mode
To turn on the Numeric mode, press Fn + F11. Now try numeric data entry
using the keys in the following figure. Press Fn + F11 again to turn off the
overlay.
The numeric keypad overlay
5-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Keyboard
Temporarily using normal keyboard (overlay on)
While using the overlay, you can temporarily access the normal keyboard
without turning off the overlay:
1. Hold Fn and press any other key. All keys will operate as if the overlay
were off.
2. Type upper-case characters by holding Fn + Shift and pressing a
character key.
3. Release Fn to continue using the overlay.
Generating ASCII characters
Not all ASCII characters can be generated using normal keyboard
operation. But, you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold down Alt + Fn.
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display
screen.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-7
The Keyboard
5-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 6
Power and Power-Up Modes
The computer's power resources include the AC adaptor and internal
batteries. This chapter gives details on making the most effective use of
these resources including charging and changing batteries, tips for saving
battery power, and power up modes.
Power conditions
The computer's operating capability and battery charge status are affected
by the power conditions: whether an AC adaptor is connected, whether a
battery is installed and what the charge level is for the battery.
Table Power conditions
Power on
Power off
(no operation)
Battery fully
charged
• Operates
• LED: Battery blue
Universal
AC
• LED: Battery blue
adaptor
connected
Battery partially
charged or no
charge
• Operates
• Quick charge
• Quick Charge
• LED: Battery orange
• LED: Battery orange
No battery
installed
• Operates
• No charge
• No charge
• LED: Battery off
• LED: Battery off
Battery charge is • Operates
above low battery
trigger point
Universal
AC
adaptor
not
• LED: Battery off
Battery charge is • Operates
connected
below low battery
trigger point
• LED: Battery flashes orange
Battery charge is Computer shuts down
exhausted
No Battery
installed
• Cannot operates
• LED: Battery off
User’s Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Power indicators
As shown in the above table, the Battery. Power indicators on the system
indicator alert you to the computer’s operating capability and battery charge
status.
Battery indicator
Check the Battery indicator to determine the status of the battery pack.
The following indicator lights indicate the battery status:
Flashing orange
Orange
The battery charge is low. The AC adaptor must
be connected to recharge the battery.
Indicates the AC adaptor is connected and
charging the battery.
Blue
Indicates the AC adaptor is connected and the
battery is fully charged.
No light
Under any other conditions, the indicator does
not light.
If the battery becomes too hot while it is being charged, the charge will
stop and the battery indicator will go out. When the battery’s temperature
falls to a normal range, charge will resume. This occurs whether the
computer's power is on or off.
Power indicator
Check the Power indicator to determine the power status:
Blue
Indicates power is being supplied to the
computer and the computer is turned on.
Blinking orange
Indicates power is being supplied to the
computer while the computer is in Standby
Mode. The indicator turns on for one second
and off for two seconds.
No light
Under any other conditions, the indicator does
not light.
6-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Battery types
The computer has the following batteries:
■ Battery pack ( 3cell, 6cell, or 9cell depending on the model.)
■ Real Time Clock (RTC) battery
■ The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.
■ Do not remove the battery pack while the computer is in Standby Mode.
Data is stored in RAM, so if the computer loses power it will be lost.
When the computer is powered off in Standby Mode, and the
AC adaptor is not connected, the main battery pack supplies power to
maintain data and programs in memory. If the battery pack is
completely discharged, Standby Mode does not function and the
computer loses all data in memory.
Battery pack
When the AC adaptor is not connected, the computer's main power source
is a removable lithium ion battery pack, also referred to in this manual as
the main battery. You can purchase additional battery packs for extended
use of the computer away from an AC power source.
Before you remove the battery pack, set the computer to Hibernation Mode
or save your data and shut down the computer. Do not change the battery
pack while the AC adaptor is connected.
Battery pack
To ensure that the battery pack maintains its maximum capacity, operate
the computer on battery power at least once a month until the battery pack
procedures. If the computer is continuously operated on AC power through
an AC adaptor for an extended period, more than a month, the battery may
fail to retain a charge. It may not function efficiently over the expected life of
the battery and the Battery indicator may not indicate a low-battery
condition.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3
Power and Power-Up Modes
Real Time Clock battery
The Real Time Clock (RTC) battery provides power for the internal real
time clock and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this
data and the real time clock and calendar stop working.
The computer's RTC battery is a lithium ion battery and should be replaced
only by your dealer or by a TOSHIBA service representative. The battery
can explode if not properly replaced, used, handled or disposed of.
Dispose of the battery as required by local ordinances or regulations.
■ You can change the settings of the Real Time Clock by pressing F2 in
POST.
■ After configuring the time and date for the Real Time Clock battery, we
recommend that you turn the power status of your computer to "ON" so
that the Real Time Clock battery is charged. Refer to Chapter 9
Troubleshooting, for details.
If the following message is displayed on the LCD:
ERROR 0271: Check date and time settings.
WARNING 0251: System CMOS checksum bad-Default configuration
used.
Press [F1] to resume, [F2] to setup.
The charge in the RTC battery is getting low or has been exhausted. You
will need to set the date and time within the BIOS setup using the following
steps:
1. Press F2 key - the BIOS setup screen will be displayed.
2. Set the date in System Date.
3. Set the time in System Time.
4. Press F10 key. Confirmation message will appear.
Press Enter key. BIOS setup will terminate and the computer will be
rebooted.
After configuring the date and time it is recommended that you switch the
computer on and then leave it in this state so that the Real Time Clock
battery can be charged.
6-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Care and use of the battery pack
The battery pack is a vital component of portable computing. Taking proper
care of it will help ensure longer operating time on battery power as well as
a longer life for your battery pack. Follow the instructions in this section
carefully to ensure safe operation and maximum performance.
Safety precautions
Mishandling of batteries can cause death, serious injury or property
damage. Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, which if not avoided,
may result in moderate or minor injury or property damage.
Note: Provides important information.
Danger
1. Never try to dispose of the battery pack by burning or expose it to a
heating device such as a microwave oven. The battery pack could
explode and cause bodily injury.
2. Never try to disassemble, repair or otherwise tamper with a battery
pack. The battery pack will overheat and ignite. Leakage of caustic
alkaline solution or other electrolytic substances will cause fire or injury,
possibly resulting in death or serious injury.
3. Never short-circuit the battery pack by contacting the terminals with a
metal object. A short-circuit can cause fire or otherwise damage the
battery pack and possibly cause injury. To avoid accidental short-circuit,
always wrap the battery pack in plastic and cover the terminals with
electrical tape when storing or disposing of the battery pack.
4. Never puncture the battery pack with a nail or other sharp object. Never
strike it with a hammer or other object. Never step on it.
5. Never try to charge the battery pack in any manner other than that
described in the User's manual. Never connect the battery pack to a
plug socket or to an automobile’s cigarette lighter socket. It may rupture
or ignite.
6. Use only the battery pack supplied with the computer or other device or
a battery pack approved by the computer or device’s manufacturer.
Battery packs have different voltages and terminal polarities. Use of an
improper battery could cause smoke, fire or rupture of the battery pack.
7. Never subject a battery pack to heat, such as storage near a heat
source. Exposure to heat can cause the battery pack to ignite, explode
or leak caustic liquid and cause death or serious injury. It could also fail
or malfunction causing data loss.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5
Power and Power-Up Modes
8. Never expose the battery pack to abnormal shock, vibration or
pressure. The battery pack’s internal protective device will fail, causing
it to overheat, explode, ignite or leak caustic liquids possibly resulting in
death or serious injury.
9. Never let a battery pack become wet. A wet battery pack will overheat,
ignite or rupture possibly resulting in death or serious injury.
Warning
1. Never allow caustic electrolyte fluid leaked from a battery pack to
contact your eyes, skin or clothing. If caustic electrolyte fluid should
contact your eyes, immediately wash your eyes with large amounts of
running water and seek medical attention, to help prevent eye damage.
If electrolyte fluid should contact your skin immediately wash it under
running water to prevent rash. If it contacts your clothes, promptly
remove them to prevent the fluid from contacting your skin or eyes.
2. Immediately turn off the power, disconnect the AC adaptor and remove
the battery if any of the following events are observed in the battery
pack: offensive or unusual odor, excessive heat, discoloration or
deformation. Never use the computer again until it has been checked
by a TOSHIBA service provider. It might generate smoke or fire, or the
battery pack might rupture.
3. Make sure the battery is securely installed in the computer before
attempting to charge the battery pack. Improper installation could
generate smoke or fire, or cause the battery pack to rupture.
4. Keep the battery pack out of reach of infants and children. It can cause
injury.
Caution
1. Never continue to use a battery pack after its recharging capacity has
become impaired, or after the display of a warning message indicating
that the battery pack’s power is exhausted. Continued use of an
exhausted or impaired battery pack could cause the loss of data.
2. Never dispose of battery packs with normal trash. Bring them to your
TOSHIBA dealer or to another recycling centre to save resources and
prevent environmental damage. Cover the terminals with electrical tape
to prevent short-circuits, which could cause the battery pack to ignite or
rupture.
3. Use only battery packs recommended by TOSHIBA as replacements.
4. Always make sure the battery pack is installed correctly and securely.
Otherwise, a battery pack could fall out and possibly cause injury.
5. Charge the battery pack only in an ambient temperature between 5 and
35 degrees Celsius. Otherwise, the electrolyte solution might leak,
battery pack performance might deteriorate and the battery life might be
shortened.
6-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
6. Be sure to monitor the remaining battery power. If the battery pack and
real time clock battery discharge completely, Standby Mode will not
function and data in memory will be lost. Also, the computer might
register an incorrect time and date. In this case, connect the
AC adaptor to recharge the batteries.
7. Never install or remove the battery pack without first turning off the
power and disconnecting the AC adaptor. Never remove the battery
pack while the computer is in Suspend or Standby Mode. Data will be
lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable
the Wake-up on LAN function.
2. After the battery pack is charged, avoid leaving the AC adaptor
connected and the computer turned off for more than a few hours at a
time. Continuing to charge a fully-charged battery pack can damage the
battery.
Charging the batteries
When the power in the battery pack becomes low, the Battery indicator
flashes orange indicating that only a few minutes of battery power remain.
If you continue to use the computer while the Battery indicator flashes, the
computer enables Hibernation Mode (so you don't lose data) and
automatically turns off.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack while it is installed in the computer, connect the
AC adaptor to the DC IN 19V jack and plug the other end into a working
outlet.
The Battery indicator glows orange when the battery is being charged.
Use only the computer connected to an AC power source to charge the
battery pack. Never attempt to charge the battery pack with any other
charger.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-7
Power and Power-Up Modes
Time
The following table shows the approximate time required to fully charge a
discharged battery.
Charging time (hours)
Battery type
Power on
Power off
Battery pack
(3cell, 6cell, 9cell)
About 12 or
longer
About 4
RTC battery
About 24
Doesn't charge
The charging time when the computer is on is affected by ambient
temperature, the temperature of the computer and how you use the
computer. If you make heavy use of external devices, for example, the
battery might scarcely charge at all during operation. Refer also to the
Battery charging notice
The battery may not charge right away under the following conditions:
■ The battery is extremely hot or cold. If the battery is extremely hot, it
might not charge at all. To ensure the battery charges to its full capacity,
charge the battery at room temperature of 10° to 30°C (50° to 88°F).
■ The battery is nearly completely discharged. Leave the AC adaptor
connected for a few minutes and the battery should begin charging.
The Battery indicator may show a rapid decrease in battery operating time
when you try to charge a battery under the following conditions:
■ The battery has not been used for a long time.
■ The battery has completely discharged and been left in the computer for
a long time.
■ A cool battery is installed in a warm computer.
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power
on until the power automatically shuts off.
2. Plug in the AC adaptor.
3. Charge the battery until the Battery indicator glows blue.
Repeat these steps two or three times until the battery recovers normal
capacity.
Leaving the AC adaptor connected will shorten battery life. At least once a
month, run the computer on battery power until the battery is fully
discharged, then recharge the battery.
6-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Monitoring battery capacity
Remaining battery power can be monitored using the following methods.
■ Clicking the battery icon on the task bar
■ Via the Windows Mobility Center window
■ Wait at least 16 seconds after turning on the computer before trying to
monitor the remaining operating time. The computer needs this time to
check the battery's remaining capacity and to calculate the remaining
operating time, based on the current power consumption rate and
remaining battery capacity. The actual remaining operating time may
differ slightly from the calculated time.
■ With repeated discharges and recharges, the battery’s capacity will
gradually decrease. Therefore, an often used, older battery will not
operate for as long as a new battery even when both are fully charged.
Maximizing battery operating time
A battery’s usefulness depends on how long it can supply power on a
single charge.
How long the charge lasts in a battery depends on:
■ CPU processing speed (Depends on the model you purchased)
■ Screen brightness
■ Cooling method (Depends on the model you purchased)
■ System Standby Mode
■ System Hibernation
■ Monitor power off
■ How often and how long you use the hard disk, optical disc.
■ How much charge the battery contained to begin with.
■ How you use optional devices, such as a PC Card, to which the battery
supplies power.
■ Enabling Standby Mode conserves battery power if you are frequently
turning the computer off and on.
■ Where you store your programs and data.
■ Closing the display when you are not using the keyboard saves power.
■ Operating time decreases at low temperatures.
■ The condition of the battery terminals. Make sure the battery terminals
stay clean by wiping them with a clean dry cloth before installing the
battery pack.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-9
Power and Power-Up Modes
Retaining data with power off
When you turn off your computer with fully charged batteries, the batteries
retain data for the following approximate time periods.
Battery pack
(3cell, 6cell, 9cell)
Approximately 1.5 days
(Standby Mode, 3-cell)
Approximately 3 days
(Standby Mode, 6-cell)
Approximately 5 days
(Standby Mode, 9-cell)
Approximately 1 month
(Shut down mode, All type of battery
packs)
RTC battery
Approximately 1 month
Extending battery life
To maximize the life of your battery pack:
■ At least once a month, disconnect the computer from a power source
and operate it on battery power until the battery pack fully discharges.
Before doing so, follow the steps below.
1. Turn off the computer's power.
2. Disconnect the AC adaptor and turn on the computer's power. If it
does not turn on go to step 4.
3. Operate the computer on battery power for five minutes. If the
battery pack has at least five minutes of operating time, continue
operating until the battery pack is fully discharged. If the Battery
indicator flashes or there is some other warning to indicate a low
battery, go to step 4.
4. Connect the AC adaptor to the computer and the power cord to a
power outlet. The Battery indicator should glow orange to indicate
that the battery pack is being charged. If the Battery indicator does
not glow, power is not being supplied. Check the connections for the
AC adaptor and power cord.
5. Charge the battery pack until the Battery indicator glows blue.
■ If you have extra battery packs, rotate their use.
■ If you will not be using the system for an extended period, more than
one month, remove the battery pack.
■ Store spare battery packs in a cool dry place out of direct sunlight.
6-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Replacing the battery pack
When the battery pack reaches the end of its operating life you will need to
install a new one. The life of the battery pack is generally about 500
recharges. If the Battery indicator flashes orange shortly after fully
recharging the battery, the battery pack needs to be replaced.
You might also replace a discharged battery pack with a charged spare
when you are operating your computer away from an AC power source.
This section explains how to remove and install the battery pack.
Removing the battery pack
To replace a discharged battery, follow the steps below.
■ When handling battery packs, do not short-circuit the terminals. Also do
not drop, hit or otherwise apply impact; do not scratch or break the
casing and do not twist or bend the battery pack.
■ Do not remove the battery pack while the computer is in Standby Mode.
Data is stored in RAM, so if the computer loses power it will be lost.
■ In Hibernation Mode, data will be lost if you remove the battery or
disconnect the AC adaptor before the save is completed. Wait for the
Built-in HDD indicator to go out.
■ Do not touch the latch while holding the computer. Or you may get
injured by the dropped battery by unintentional release of the latch.
1. Save your work.
2. Turn the computer's power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Turn the computer upside down.
5. Slide and hold the battery release latch to free the battery pack after
moving the battery pack lock into its unlock position - then slide the
battery pack out of the computer.
Battery Release Latch
Battery pack
Battery
Pack
Lock
Releasing the battery pack
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-11
Power and Power-Up Modes
Installing the battery pack
To install a battery, follow the steps below.
■ The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.
■ Do not touch the latch while holding the computer. Or you may get
injured by the dropped battery by unintentional release of the latch.
1. Turn the computer's power off.
2. Disconnect all cables connected to the computer.
3. Insert the battery pack.
4. Ensure the battery pack lock is moved into its locked position.
Battery pack
Battery
Pack
Lock
Securing the battery pack
Starting the computer by password
To start up the computer with the user password, follow these steps:
following message appears:
Password=
At this point, the hotkeys Fn + F1 to F9 do not work. They will function after
you enter the password.
2. Enter the password.
3. Press Enter.
If you enter the password incorrectly three times in a row, the computer
shuts off. In this case, you must turn the computer back on to retry
password entry.
6-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
or if available
Swipe your fingerprint on the sensor if you have already registered the
fingerprint with the Fingerprint utility and enabled Fingerprint Power on
Security. If you would not like to swipe your finger or cannot authenticate
the fingerprint for some reasons, push the BkSp key to skip the fingerprint
authentication screen. You can try to swipe the fingerprint up to five times.
If you failed fingerprint authentication more than five times, you must enter
the password manually to start the computer.
Power-up modes
The computer has the following power-up modes:
■ Boot Mode: Computer shuts down without saving data. Always save
your work before you turn the computer off in boot mode.
■ Hibernation Mode: Data in memory is saved to the hard disk.
■ Standby Mode: Data is maintained in the computer's main memory.
Hot keys
You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter
Panel power off/on
You can set up your computer so that power turns off automatically when
you close the display panel. When you open the panel, power turns on in
Standby Mode or Hibernation Mode but not in boot mode.
If the panel power off function is enabled and you use Shut down
®
Windows , do not close the display until the shut down function is
completed.
System Auto Off
This feature turns the system off automatically if it is not used for a set
duration. The system shuts down in Standby Mode or Hibernation Mode in
®
Windows .
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-13
Power and Power-Up Modes
6-14
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 7
HW Setup
This chapter explains how to use TOSHIBA HW Setup program to
configure your computer. TOSHIBA HW Setup lets you configure settings
for General, Password, Display, Boot Priority, Keyboard, LAN, and USB.
Accessing HW Setup
To run HW Setup, click start, click Control Panel, click Printers and Other
Hardware and select TOSHIBA HW Setup.
HW Setup Window
The HW Setup window contains the following tabs: General, Password,
Display, Boot Priority, Keyboard, USB and LAN .
There are also these three buttons:
OK
Accepts your changes and closes the HW Setup
window.
Cancel
Apply
Closes the window without accepting your
changes.
Accepts all your changes without closing the HW
Setup window.
General
This window displays the BIOS version and contains two buttons:
Default
Return all HW Setup values to the factory
settings.
About
Display the HW Setup version.
Setup
This field displays BIOS Version and date.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-1
HW Setup
Password
This tab allows you to set or reset the user password for power on.
User Password
Lets you register a new password or un-register an existing password.
Not Registered
Registered
Un-registers an existing password
Register a new password by following the on
screen instructions
Owner String
This blank field is used to display a message when the password field is
displayed on startup. If a password is not registered the message will not
be shown. The maximum length is 256 characters.
Display
This tab lets you select the internal LCD and/or external monitor when the
computer boots up.
Power On Display
Lets you select the display to be used when the computer is booted (This
setting is only available on Standard VGA mode and not available on
®
Windows Desktop).
Auto-Selected
Selects an external monitor if one is connected.
Otherwise, it selects the internal LCD (Default).
LCD + Analog RGB
Selects both the internal LCD and external
monitor for simultaneous display.
Boot Priority
Boot Priority Options
This option sets the priority for booting the computer.
To select the boot drive you want, follow the steps below.
1. Boot-up your computer and press F12 to enter the boot menu.
2. The boot select screen will be displayed: Hard disk Drive, CD/DVD,
FDD and LAN.
3. Use the upper/lower cursor keys to highlight the boot device you want
and apply.
7-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HW Setup
Keyboard
Wake-up on Keyboard
When this feature is enabled and the computer is in Standby Mode, you
can turn on the computer by pressing any key. It is effective only for the
internal keyboard and only when the computer is in Standby Mode.
Enabled
Disabled
Enables the Wake-up on Keyboard function.
Disables the Wake-up on Keyboard function
(Default).
USB
USB Keyboard/Mouse/FDD Legacy Emulation
Use this option to enable or disable Legacy USB support. If your operating
system does not support USB, you can still use a USB mouse, keyboard,
and FDD by setting the Legacy USB Support to enable.
LAN
Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled
Disabled
Enables Built-in LAN function (Default).
Disables Built-in LAN function.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-3
HW Setup
7-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 8
Optional Devices
Optional devices can expand the computer's capabilities and its versatility.
This chapter describes connection or installation of the following devices,
which are available from your TOSHIBA dealer:
Cards/memory
■ PC Card and Express Card
■ SD (Secure Digital) / MMC (Multi Media Card) / MS (Memory Stick) / MS
Pro (Memory Stick Pro) / xD (xD-Picture Card) cards
■ Memory expansion
Power devices
■ Additional battery pack
■ Additional AC adaptor
Peripheral devices
■ External monitor
Other
■ Security lock
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-1
Optional Devices
PC Card and Express Card
The computer is equipped with a PC Card expansion slot that can
accommodate one Type II card or one Express Card. Any PC Card that
meets industry standards (manufactured by TOSHIBA or other vendor) can
be installed. The slot supports 16-bit PC Cards, including PC Card 16’s
multifunction card and CardBus PC Cards.
CardBus supports the new standard of 32-bit PC Cards. The bus provides
superior performance for the greater demands of multimedia data
transmission.
The Express Card expansion slot can accommodate two standard module
formats; anExpress Card/34 module and an Express Card/54 module. An
Express Card module is a small, modular add-in card technology based on
PCI Express and Universal Serial Bus (USB) interfaces.
Inserting a PC card and Express Card
One Express Card connector is located on the right side of the computer.
The computer's hot-install feature lets you install Express Card while the
computer's power is on.
To install an Express Card, follow the steps below.
1. Insert the Express Card.
2. Press gently to ensure a firm connection.
®
Windows hot-install feature lets you insert a PC card and Express Card
while the computer’s power is on.
PC or Express Card
Inserting the PC or Express Card
8-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Devices
After inserting the card, refer to the card’s documentation and check the
®
configuration in Windows to make sure it is appropriate for your card.
Removing a PC Card or Express Card
■ Before removing a Card, make sure that any applications or system
services do not use the card.
■ Be sure to disable the Card prior to removing it. Otherwise, the system
may be fatally damaged.
To remove the PC Card, follow the steps below.
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Click the Card you want to remove.
3. Press the Card once to extend it.
4. Grasp the extended Card, and remove it.
PC or Express Card
Eject button
Removing the PC or Express Card
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-3
Optional Devices
SD/MMC/MS/MS Pro/xD Memory cards
The computer is equipped with a multiple digital media card slot that can
accommodate SD/MMC/MS/MS Pro/xD memory cards. These memory
cards let you easily transfer data from devices, such as digital cameras and
Personal Digital Assistants, which use flash-memory.
Card Type
Capacities
SD
up to 2GB
up to 2GB
MMC
MS
up to 128MB, 256MB (128MB x 2)
up to 2GB
MS Pro
xD
up to 2GB
Keep foreign objects out of the memory card slot. A pin or similar object
can damage the computer's circuitry.
®
Do not format a memory card with Windows as it might result in that card
not being able to be used with some peripheral devices.
Memory Stick Duo/PRO Duo and the Memory Stick adaptor are not
compatible with the Multiple Digital Media Card Slot. Do not insert Memory
Stick Duo/PRO Duo into the slot. Data may be lost or damaged if you use
any card other than those supported.
The card is designed so that it can be inserted only one way. Do not try to
force the card into the slot.
For more details on using memory cards, see manuals accompanying the
cards.
The Logo of SD memory card is
.
8-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Devices
Installing a memory card
To install a memory card:
1. Insert the memory card.
2. Press gently to ensure a firm connection.
Inserting a memory card
Be sure the memory card is oriented properly before you insert it.
®
If Windows fails to read the card, remove it then re-insert it.
■ The multiple digital media card slot only accepts one type of card at a
time. Do not attempt to install more than one card as you risk damaging
either the cards themselves or the computer.
Removing a memory card
To remove a memory card, follow the steps below:
1. Click the Safely Remove Hardware icon on the Taskbar.
2. Select a device, then click the Stop button. A confirmation dialog may
appear, depending on how the device is registered with the system; if
so, confirm that you want to remove the device.
3. Gently press the memory card inside the socket to eject it.
4. Grasp the card and remove it.
Removing a memory card
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-5
Optional Devices
■ Make sure the memory card indicator is out before you remove the
card or turn off the computer's power. If you remove the card or turn off
the power while the computer is accessing the card you may lose data
or damage the card.
■ Do not remove the card while the computer is in standby or Hibernation
mode. The computer could become unstable or data in the memory
card could be lost.
■ Do not turn off or place the computer into either Standby Mode or
Hibernation Mode while data is being transferred to or from the memory
card. The system may become unstable or data in the memory card
may be lost.
Memory card care
Set the write-protect switch to the lock position, if you do not want to record
data.
1. Do not write to a memory card if the battery power is low. Low power
could affect writing accuracy.
2. Do not remove a memory card while read/write is in progress.
3. The memory card is designed so that it can be inserted only one way.
Do not try to force the card into the slot.
4. Do not leave a memory card partially inserted in the slot. Press the
memory card until you hear it click into place.
5. Do not twist or bend memory cards.
6. Do not expose memory cards to liquids or store in humid areas or lay
media close to containers of liquid.
7. After using a memory card, return it to its case.
8. Do not touch the metal part or expose it to liquids or let it get dirty.
8-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Devices
Memory expansion
You can install additional memory in the computer's memory module socket
to increase the amount of RAM. This section describes how to install and
remove a memory module.
■ Use only memory modules approved by TOSHIBA.
■ Do not try to install or remove a memory module under the following
conditions. You can damage the computer and the module. Also, data
will be lost.
a. The computer is turned on.
b. The computer was shut down using the Standby Mode or
Hibernation Mode.
■ Expansion memory is a precision electronic component that may be
fatally damaged by static electricity. Since the human body has slight
static electricity, be sure to discharge static electricity from your body
before installing an expansion memory module. To discharge your
body's static electricity, simply touch any metal close to you with bare
hands.
Use a point size 1 Phillips screwdriver to remove and fasten the screws.
Use of an incorrect screwdriver can damage the screw heads.
Installing a memory module
Follow the steps below to install a memory module.
1. Set the computer to boot mode and turn off the power.
2. Remove all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack (refer to
4. Loosen the screws securing the memory module cover.
5. Slide your fingernail or a thin object under the cover and lift it off.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-7
Optional Devices
Memory
Module Cover
Removing the memory module cover
6. Lift one side of the insulator sheet and fit the module's connectors into
the computer's connectors at about a 45 degree angle. Press the
module carefully to ensure a firm connection.
Do not touch the connectors on the memory module or on the computer.
Debris on the connectors may cause memory access problems.
Slot A is reserved for main memory. Use slot B for expanded memory. If
only one card is installed use slot A.
7. Push the module down so it lies flat. Latches on either side will click into
place to secure the module.
Slot B
Slot A
Installing the memory module
8-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Devices
8. Seat the cover and secure it with the screws.
10. Turn the power on and make sure the added memory is recognized.
Open System in the Control Panel and click the General tab.
Points to note about memory module error
If you install a memory module that is not compatible with the computer, the
Power indicator will flash (on for 0.5 seconds, off for 0.5 seconds) in the
following ways:
■ If there is only an error in Slot A: repeatedly flashes orange twice, then
blue.
■ If there is only an error in Slot B: repeatedly flashes orange, then blue
twice.
■ If there is an error in Slot A and in Slot B: repeatedly flashes orange
twice, then blue twice.
In all instances you should shut down the computer and remove the
incompatible module(s)
Removing a memory module
To remove the memory module, make sure the computer is in boot mode
then:
1. Be sure the power is off and all cables are disconnected from the
computer.
2. Turn the computer upside down and remove the battery and the screws
securing the memory module cover.
3. Slide your fingernail or a thin object under the cover and lift it off.
4. Lift one side of the insulator and push the latches to the outside to
release the module. A spring will force one end of the module up.
5. Grasp the module by the sides and pull it out.
■ If you use the computer for a long time, the memory modules will
become hot. In this case, let the memory modules cool to room
temperature before you replace them. Or you will get burnt if you touch
any of them.
■ Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access
problems.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-9
Optional Devices
Latches
1
2
1
Removing the memory module
6. Seat the cover and secure it with screws and replace the battery pack.
Additional battery pack
You can increase the portability of the computer with additional battery
packs. If you’re away from an AC power source and your battery runs low,
you can replace it with a freshly charged battery. Refer to Chapter 6, Power
Additional AC adaptor
If you frequently transport the computer between different sites such as
your home and office, purchasing an AC adaptor for each location will
reduce the weight and bulk of your carrying load.
8-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Devices
External monitor
An external analog monitor can be connected to the external monitor port
on the computer. The computer supports several video modes. Refer to
steps below.
1. Turn the computer off.
2. Connect the monitor to the external monitor port.
3. Turn the monitor's power on.
4. Turn the computer on.
®
®
When you turn on the power, the Windows Bootup screen (Windows
Logo) appears on the display device.
®
However, the Windows Desktop appears on a display device that you
used last time to shut down your PC, if the display device exists when you
turn on the power.
To change the display settings, press Fn+F5. If you disconnect the monitor
before you turn the computer off, be sure to press Fn+F5 to switch to the
keys to change the display setting.
Security lock
Security locks enable you to anchor your computer to a desk or other heavy
object to help prevent unauthorized removal of the computer.
The computer has a security lock slot on the left side. Attach one end of the
cable to a desk and the other end to the security lock slot.
1. Turn the computer so the left side faces you.
2. Align the holes for the security lock and attach the lock.
Security lock
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-11
Optional Devices
8-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Chapter 9
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems
occur, following the procedures in this chapter can help to determine the
cause.
All readers should become familiar with this chapter. Knowing what might
go wrong can help prevent problems from occurring.
Problem solving process
Resolving problems will be much easier if you observe the following
guidelines:
■ Stop immediately when you recognize a problem exists. Further action
may result in data loss or damage. You may destroy valuable problem
related information that can help solve the problem.
■ Observe what is happening. Write down what the system is doing and
what actions you performed immediately before the problem occurred.
If you have a printer attached, print a copy of the screen using PrtSc.
The questions and procedures offered in this chapter are meant as a guide,
they are not definitive problem solving techniques. Many problems can be
solved simply, but a few may require help from your dealer. If you find you
need to consult your dealer or others, be prepared to describe the problem
in as much detail as possible.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-1
Troubleshooting
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to
fix and yet can cause what appears to be a serious problem.
■ Make sure you turn on all peripheral devices before you turn on the
computer. This includes your printer and any other external device you
are using.
■ Before you attach an external device, turn the computer off. When you
turn the computer back on it recognizes the new device.
■ Make sure all options are set properly in the setup program.
■ Check all cables. Are they correctly and firmly attached? Loose cables
can cause signal errors.
■ Inspect all connecting cables for loose wires and all connectors for
loose pins.
■ Check that your CD/DVD/CD-RW is correctly inserted.
Make notes of your observations and keep them in a permanent error log.
This will help you describe your problems to your dealer. If a problem
recurs, the log will help you identify the problem faster.
Analyzing the problem
Sometimes the system gives clues that can help you identify why it is
malfunctioning. Keep the following questions in mind:
■ Which part of the system is not operating properly: keyboard, hard disk
drive, optical media drive, display. Each device produces different
symptoms.
■ Is the operating system configuration set properly? Check the
configuration options.
■ What appears on the display screen? Does it display any messages or
random characters? Print a copy of the screen if you have a printer
attached. Look up the messages in the software and operating system
documentation. Check that all connecting cables are correctly and
firmly attached. Loose cables can cause erroneous or intermittent
signals.
■ Do any indicators light? Which ones? What color are they? Do they stay
on or blink? Write down what you see.
■ Do you hear any beeps? How many? Are they long or short? Are they
high pitched or low? Is the computer making any unusual noises? Write
down what you hear.
Record your observations so you can describe them to your dealer.
9-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Software
The problems may be caused by your software or
disc. If you cannot load a software package, the
media may be damaged or the program might be
corrupted. Try loading another copy of the
software.
If an error message appears while you are using
a software package, check the software
documentation. These documents usually include
a problem solving section or a summary of error
messages.
Next, check any error messages in the operating
system documentation.
Hardware
If you cannot find a software problem, check your
hardware.
First run through the items in the preliminary
checklist above. If you still cannot correct the
problem, try to identify the source. The next
section provides checklists for individual
components and peripherals.
Hardware and system checklist
This section discusses problems caused by your computer's hardware or
attached peripherals. Basic problems may occur in the following areas:
■ System start-up
■ Self test
■ USB
■ Memory expansion
■ Sound system
■ Monitor
■ Power
■ Real Time Clock
■ Keyboard
■ Modem
■ LCD panel
■ LAN
■ Hard disk drive
■ Recovery Discs
■ DVD Super Multi drive
■ Pointing device
■ Wireless LAN
■ FingerPrint Sensor
■ PC/Express Card
System start-up
When the computer does not start properly, check the following items:
■ Self Test
■ Power Sources
■ Power-on Password
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-3
Troubleshooting
Self test
When the computer starts up, the self test will be run automatically, and the
following will be displayed:
In Touch with Tomorrow
TOSHIBA
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating
system, depending on how the Boot Priority is set in the TOSHIBA HW
Setup program.
If any of the following conditions are present, the self test failed:
■ The computer stops and does not proceed to display information or
messages except the TOSHIBA logo.
■ Random characters appear on the screen, and the system does not
function normally.
■ The screen displays an error message.
Turn off the computer and check all cable connections. If the test fails
again, contact your dealer.
Power
When the computer is not plugged into an AC outlet, the battery pack is the
primary power source. However, your computer has a number of other
power resources, including an intelligent power supply and a Real Time
Clock battery. These resources are interrelated and any one could affect
apparent power problems. This section provides checklists for AC power
and the battery. If you cannot resolve a problem after following them, the
cause could lie with another power resource. In such a case, contact your
dealer.
Overheating power down
If the computer's internal temperature becomes too high, the computer will
automatically enter Hibernation Mode or Standby Mode and shut down. If
the computer has reached room temperature and still does not start, or if it
starts but shuts down quickly contact your dealer.
9-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
AC power
If you have trouble turning on the computer with the AC adaptor connected,
Modes for more information.
Problem
Procedure
AC adaptor doesn’t
power the computer
Check the connections. Make sure the cord is
firmly connected to the computer and a power
outlet.
Check the condition of the cord and terminals. If
the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the AC adaptor still does not power the
computer, contact your dealer.
Battery
If you suspect a problem with the battery, check the Battery indicator. For
information on indicator and battery operation refer to Chapter 6, Power
Problem
Procedure
Battery doesn't power The battery may be discharged. Connect the AC
the computer adaptor to charge the battery.
Battery doesn’t charge If the battery is completely discharged, it will not
when the AC adaptor is begin charging immediately. Wait a few minutes.
attached ( Battery
indicator does not glow
orange.)
If the battery still does not charge, make sure the
outlet of the AC adaptor is supplying power.
Test it by plugging in an appliance.
Check whether the battery is hot or cold to the
touch. If the battery is too hot or too cold, it will
not charge properly. Let it reach room
temperature.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-5
Troubleshooting
Problem
Procedure
Unplug the AC adaptor and remove the battery to
make sure the terminals are clean. If necessary
wipe them with a soft dry cloth dipped in alcohol.
Connect the AC adaptor and replace the battery.
Make sure it is securely seated.
Check the Battery indicator. If it does not glow,
let the computer charge the battery for at least
20 minutes. If the Battery indicator glows after
20 minutes, let the battery continue to charge at
least another 20 minutes before turning on the
computer.
If the indicator still does not glow, the battery may
be at the end of its operating life. Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn’t power If you frequently recharge a partially charged
the computer as long as battery, the battery might not charge to its full
expected
potential. Fully discharge the battery, then try to
charge it again.
Check the power consumption settings in the
Power Options. Consider using a power saving
feature.
Disposing of PC and PC batteries
■ Discard this PC in accordance with applicable laws and regulations. For
further information, contact your local government.
■ This PC contains rechargeable batteries. After repeated use, the
batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.
■ Please be kind to our shared environment. Check with your local
government authority for details regarding where to recycle old batteries
or how to dispose of them properly. This product contains mercury.
Disposal of this material may be regulated due to environmental
considerations. For disposal, reuse or recycling information, please
contact your local government.
■ If your hard disk or other storage media contains sensitive data, you
should be aware that standard deletion procedures do not remove data
from the media. These standard deletion procedures include:
■ Selecting Delete for a target file
■ Putting files in the Recycle Bin and emptying the Recycle Bin
9-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ Reformatting the media
■ Reinstalling an operating system from the recovery CD-ROM
The procedures above delete only the initial part of the data used for file
management. This makes the file invisible to the operating system, but
the data can still be read by specialized utilities. If you dispose of the
PC, please delete all the data on its hard disk drive. Doing so prevents
unauthorized use of such data. To ensure your data is not used for
unauthorized purposes, you can:
■ Physically destroy the hard disk drive
■ Use a proven specialized utility to overwrite all data
■ Take the hard disk drive to a professional deletion service
Real Time Clock
Problem
The BIOS setting and Charge in the RTC battery is exhausted or
Procedure
system date/time are
lost.
getting low. You will need to set the date and time
in the BIOS setup screen using the following
procedure
1. Press F2 key. BIOS setup will boot up.
2. Set the date in System Date.
3. Set the time in System Time.
4. Press F10 key. Confirmation message will
appear.
5. Press Enter key. BIOS setup will terminate
and the computer will be rebooted.
After configuring the time and date for the Real Time Clock battery, we
recommend that you turn the power status of your computer to "ON" so
that the Real Time Clock battery is charged.
Keyboard
Keyboard problems can be caused by your setup configuration. For more
Problem
Procedure
Some letter keys
produce numbers
Check that the numeric keypad overlay is not
selected. Press Fn + F11 and try typing again.
Output to screen is
garbled
Make sure the software you are using is not
remapping the keyboard. Remapping involves
reassigning the meaning of each key. Refer to
your software’s documentation.
If you are still unable to use the keyboard,
consult your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-7
Troubleshooting
LCD panel
Apparent LCD problems may be related to the computer's setup.
Problem
No display
Procedure
Press hot keys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
Problems above remain Refer to your software’s documentation to
unresolved or other
problems occur
determine if the software is causing the difficulty.
Run the diagnostic test.
Contact your dealer if the problems continue.
Hard disk drive
Problem
Procedure
Computer does not boot There may be a problem with your operating
from hard disk drive
system files. Refer to your operating system
documentation.
Slow performance
Your files may be fragmented. Run disk
Defragmenter to check the condition of your files
and disk. Refer to your operating system
documentation or online help for information on
running disk Defragmenter.
As a last resort, reformat the hard disk. Then,
reload the operating system and other files.
If problems persist, contact your dealer.
9-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Recovery Discs
Problem
Procedure
The following message You will see this message if you have previously
appears when
executing Recovery
Disc Creator.
chosen to remove the partition and are trying to
create "Recovery Media". When there is no
recovery partition, the Recovery Disc Creator
cannot make Recovery Media. However, if you
have already created a "Recovery Media", you
can use it to restore the recovery partition.
"The Recovery Disc
Creator can not be
launched because there
is no recovery partition." Simply follow the instructions in "Restoring the
preinstall software from your creating Recovery
Media" section in this manual. You will be
directed to select "Restore Original Factory
Image" from the drop-down menu. If you have
not created "Recovery Media", please contact
TOSHIBA support for assistance.
DVD Super Multi drive (Supporting DVD±R Double Layer)
Problem
Procedure
You cannot access a
CD/DVD in the drive
Make sure the drive's drawer is securely closed.
Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe it
with a clean cloth dipped in water or a neutral
cleaning.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-9
Troubleshooting
Problem
Procedure
Some CD/DVDs run
The software or hardware configuration may be
correctly, but others do causing a problem. Make sure the hardware
not
configuration matches your software's needs.
Check the CD/DVDs documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM:
DVD-ROM, DVD-Video,
DVD-R, DVD-RW, DVD+R,
DVD+RW, DVD-RAM
CD-ROM:
CD-DA, CD-Text, Photo CD
(single/multi-session),
CD-ROM Mode 1, Mode 2,
CD-ROM XA Mode 2 (Form1,
Form2), Enhanced CD
(CDEXTRA)
Recordable CD: CD-R, CD-RW, DVD-R,
DVD-R(DL), DVD-RW,
DVD+R, DVD+R(DL),
DVD+RW, DVD-RAM
Check the region code on the DVD. It must
match that on the DVD Super Multi drive. Region
codes are listed in the Fixed optical media drives
Pointing device
If you are using a USB mouse, also refer to the USB section in this chapter
and to your mouse documentation.
TouchPad
Problem
Procedure
On-screen pointer does The system might be busy. If the pointer is
not respond to Pad
operation
shaped as an hourglass, wait for it to return to its
normal shape and try again to move it.
Double-tapping does
not work
Try changing the double-click speed setting in
the mouse control utility.
1. To access this utility, click start, Control
Panel, Printers and Other Hardware, then
Mouse icon.
2. Wihtin the Mouse Properties window, click
the Buttons tab.
3. Set the double-click speed as required and
click OK.
9-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Procedure
The mouse pointer
moves too fast or too
slow
Try changing the speed setting in the mouse
control utility.
1. To access this utility, click start, Control
Panel, Printers and Other Hardware, then
Mouse icon.
2. Within the Mouse Properties window, click
the Pointer Options tab.
3. Set the pointer speed as required and click
OK.
The response of the
TouchPad is too
sensitive
Adjust the touch sensitivity.
1. To access this utility, click start, Control
Panel, Printers and Other Hardware, then
Mouse icon.
2. Wihtin the Mouse Properties window, click
the Device Settings tab.
3. Click the Settings button.
4. The Properties for Synaptics Touchpad on
PS/2 port screen appears. Double-click
Sensitivity in the Select an item section on
the left side of the screen.
5. PalmCheck and Touch Sensitivity are
displayed. Click Touch Sensitivity.
6. Move the slide bar for Touch Sensitivity to
make an adjustment. Click the OK button.
7. Click the OK button on the Device Setting
tab.
USB mouse
Problem
Procedure
On-screen pointer does The system might be busy. If the pointer is
not respond to mouse shaped as an hourglass, wait for it to resume its
operation
normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-11
Troubleshooting
Problem
Procedure
Double-clicking does
not work
Try changing the double-click speed setting in
the mouse control utility.
1. To access this utility, click start, Control
Panel, Printers and Other Hardware, then
Mouse icon.
2. Wihtin the Mouse Properties window, click
the Buttons tab.
3. Set the double-click speed as required and
click OK.
The mouse pointer
moves too fast or too
slow
Try changing the speed setting in the mouse
control utility.
1. To access this utility, click start, Control
Panel, Printers and Other Hardware, then
Mouse icon.
2. Within the Mouse Properties window, click
the Pointer Options tab.
3. Set the pointer speed as required and click OK.
The mouse pointer
moves erratically
The mouse might be dirty. Refer to your mouse
documentation for instructions on cleaning.
If problems persist, contact your dealer.
USB
Also refer to your USB device’s documentation.
Problem
Procedure
USB device does not
work
Check for a firm cable connection between the
USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
®
installed. Refer to your Windows XP
documentation for information on checking the
drivers.
If problems persist, contact your dealer.
9-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Memory expansion
memory modules.
Problem
Procedure
The computer hangs up Make sure the memory module installed in the
expansion slot is compatible with the computer.
If an incompatible module has been installed,
follow the steps below.
1. Turn off the power.
2. Disconnect the AC adaptor and all peripheral
devices.
3. Remove the battery pack.
4. Remove the memory module.
5. Replace the battery pack and/or connect the
AC adaptor.
6. Turn on the power.
If problems persist, contact your dealer.
Sound system
Refer also to documentation for your audio devices.
Problem
Procedure
No sound is heard
Check the software volume settings.
Make sure the headphone connection is secure.
If problems persist, contact your dealer.
Monitor
documentation.
Problem
Procedure
Monitor does not turn
on
Make sure that the external monitor’s power
switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-13
Troubleshooting
Problem
Procedure
No display
Try adjusting the contrast and brightness controls
on the external monitor.
Press hot keys Fn + F5 to change the display
priority and make sure it is not set for the internal
display.
Display error occurs
Check that the cable connecting the external
monitor to the computer is attached firmly.
If problems persist, contact your dealer.
Modem
Problem
Procedure
Communication
Make sure the computer's internal modem
software can’t initialize settings are correct. Refer to Phone and Modem
modem Properties in the Control Panel.
You can hear a dial tone If the call is going through a PBX machine, make
but can’t make a call
sure the communication application’s tone dial
detection feature is disabled.
You can also use the ATX command.
You place a call, but a Make sure the settings are correct in your
connection can’t be
communications application.
made
After making a call you Make sure the tone or pulse selection in your
can’t hear a ring
communications application is set correctly.
You can also use the ATD command.
Communication is cut The computer will automatically cut off
off unexpectedly
communication when connection with the carrier
is not successful for a set time interval. Try
lengthening this time interval.
A CONNECT display is Check the error control setting in your
quickly replaced by NO communications application.
CARRIER
You can also use the AT\N command.
9-14
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Procedure
Character display
becomes garbled
In data transmission, make sure the parity bit and
stop bit settings correspond with those of the
during a communication remote computer.
Check the flow control and communication
protocol.
You cannot receive an Check the rings before auto answer setting in
incoming call
your communications application.
You can also use the ATS0 command.
If problems persist, contact your dealer.
LAN
Problem
Procedure
Cannot access LAN
Check for a firm cable connection between the
LAN jack and the LAN hub.
If problems persist, consult your LAN
administrator.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN
administrator. For more information on wireless communication, refer to
Problem
Procedure
Cannot access
Wireless LAN
Make sure the computer's wireless
communication switch is set to on.
If problems persist, contact your LAN
administrator.
The Wireless LAN feature is not available on all models.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-15
Troubleshooting
Fingerprint Sensor
Problem
Procedure
Reading of the
fingerprint was not
successful.
Please try again using the correct posture. Refer
Try the recognition process again using another
enrolled finger.
The fingerprint cannot Try the recognition process again using another
be read due to injuries enrolled finger.
to the finger.
If fingerprints from all the enrolled fingers cannot
be read, please log-on by using the keyboard to
input the password for the time being.
If problems persist, contact your dealer.
Fingerprint Power on
Please use TOSHIBA Password Utility to register
Security or Single Sign the User Password if it was not registered.
On feature cannot be
enabled.
1. Make sure you have enroll finger in windows
Fingerprint Power on
account.
Security does not work
2. Set the User Password by using TOSHIBA
Password Utility and restart the system.
3. Make sure place a checkmark in Replace the
power-on and hard drive passwords with
the fingerprint reader on the Protector Suite
QL setting.
PC/Express Card
Problem Procedure
PC/Express Card error Reseat the PC/Express Card to make sure it is
occurs
firmly connected.
Make sure the connection between the external
device and the card is firm.
Check the card’s documentation.
If problems persist, contact your dealer.
9-16
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for
additional technical assistance.
Before you call
Some problems you experience may be related to software or the operating
system, it is important to investigate other sources of assistance first.
Before contacting TOSHIBA, try the following:
■ Review troubleshooting sections in the documentation for software and
peripheral devices.
■ If a problem occurs when you are running software applications, consult
the software documentation for troubleshooting suggestions. Call the
software company’s technical support for assistance.
■ Consult the dealer you purchased your computer and/or software from.
They are your best sources for current information and support.
Where to write
If you are still unable to solve the problem and suspect that it is hardware
related, write to TOSHIBA at the nearest location listed on the below.
Outside of Europe
Australia
In Europe
Germany & Austria
TOSHIBA Australia Pty. Ltd.
Information Systems Division
84-92 Talavera Road
TOSHIBA Europe (I.E.) GmbH
Geschäftsbereich,
Deutschland-Österreich
North Ryde N.S.W. 2113 Sydney
Hammfelddamm8,
D-41460 Neuss, Germany
Canada
France
TOSHIBA of Canada Ltd.
191 McNabb Street,
Markham, Ontario
L3R 8H2
TOSHIBA Systèms France S.A.
7, Rue Ampère B.P. 131,
92804 Puteaux Cedex
China
Netherlands
TOSHIBA Personal Computer &
Network (Shanghai) Co. Ltd.
43F, Hongkong new world tower,
No. 300 Huai Hai Zhong Road,
Shanghai,
TOSHIBA Information Systems,
Benelux B.V.
Rivium Boulevard
41 2909 LK Capelle a/d IJssel
P.R. China 200021
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9-17
Troubleshooting
Outside of Europe
Singapore
In Europe
Spain
TOSHIBA Singapore Pte. Ltd.
438B Alexandra Road #06-01
Alexandra Technopark
TOSHIBA Information Systems,
ESPAÑA
Parque Empresarial San Fernando
Edificio Europa, la Planta,
Escalera A 28830 Madrid
Singapore 119968
United States of America
United Kingdom
TOSHIBA America Information
Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618
USA
TOSHIBA Information Systems
(U.K.) Ltd.
TOSHIBA Court
Weybridge Business Park
Addlestone Road
Weybridge, Surrey KT15 2UL
The Rest of Europe
TOSHIBA Europe (I.E.) GmbH
Geschäftsbereich,
Deutschland-Österreich
Hammfelddamm 8,
D-41460 Neuss, Germany
9-18
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Appendix A
Specifications
This appendix summarizes the computer's technical specifications.
Physical Dimensions
Weight
Size
2.1Kg
* Weight may vary depending on product
configuration, vendor components,
manufacturing variability and options selected.
310 (w) x 227 (d) x max. 34.0/min. 27.6 (h)
millimetres (not including parts that extend
beyond the main body)
Environmental Requirements
Operating
Ambient temperature 5°C to 35°C
Non-operating
-20°C to 65°C
Thermal gradient
15°C per hour maximum
20°C per hour
maximum
Relative humidity
20% to 80%
10% to 95%
Altitude (from sea
level)
0 to 3,000 meters
-60 to 10,000
meters
Power Requirements
AC adaptor
Computer
100-240 volts AC
50 or 60 hertz (cycles per second)
19 VDC
3.42 amperes
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
Specifications
Built-in Modem
Network control unit (NCU)
Type of NCU
Type of line
AA
Telephone line (analog only)
Type of dialling
Pulse
Tone
Control command
Monitor function
AT commands
EIA-578 commands
Computer's speaker
Communication specifications
Communication
System
Data:
Fax:
Full duplex
Half duplex
Communication
protocol
Data
ITU-T-Rec
(Former CCITT)
V.21/V.22/V.22bis/V.32/
V.32bis/V.34/V.90/V.92
Bell
103/212A
Fax:
ITU-T-Rec
V.17/V.29/V.27ter/V.21 ch2
(Former CCITT)
Communication
Speed
Data transmission and reception
300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600 bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/
37333/38666/40000/41333/42666/44000/45333/
46666/48000/49333/50666/52000/53333/54666/
56000 bps
Fax
2400/4800/7200/9600/12000/14400 bps
A-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Transmitting level
Receiving level
-10 dBm
-10 to -40 dBm
600 ohms ±30%
Input/output
impedance
Error correcting
Data compression
Power supply
MNP class 4 and ITU-T V.42
MNP class 5 and ITU-T V.42bis
+3.3V (supplied by computer)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
Specifications
A-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Appendix B
Display Controller and Modes
Display controller
The display controller interprets software commands into hardware
commands that turn particular picture elements (pels) on or off.
The controller is an advanced Video Graphics Array (VGA) that provides
Graphics Array (XGA) support for the internal LCD and external monitors.
The following is available:
■ 13.3", 1280 horizontal × 800 vertical pixels
A high-resolution external monitor connected to the computer can display
up to 2048 horizontal and 1536 vertical pixels at 16 M colors. (Depends on
the model you purchased.)
The display controller also controls the video mode, which uses industry
standard rules to govern the screen resolution and the maximum number of
colors that can be displayed on screen.
Software written for a given video mode will run on any computer that
supports the mode.
The computer's display controller supports all VGA modes, the most widely
used industry standards.
®
This series are equipped with Mobile Intel 965 Express display adaptors.
The video modes supported by the display chipset are shown in following
tables.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-1
Display Controller and Modes
Video modes
The computer supports video modes defined in the tables below. If your
application offers a selection of mode numbers that do not match the
numbers on the table, select a mode based on mode type, resolution,
character matrix, number of colors and refresh rates. Also, if your software
supports both graphics and text modes, the screen display may appear to
operate faster using a text mode.
If you are running some applications (for example a 3D application or video
playback and so on), you may see some disturbance, flickering or frame
dropping on your screen. If that occurs, adjust the resolution of display,
lowering it until the screen is displayed properly. You could also disable
Windows Aero™ to help correct this situation.
Table 1: Video modes (VGA)
Video Type Resolution Character
LCD
colors
CRT
colors
Scanning
frequency
Vertical (Hz)
mode
matrix
(pels)
0, 1
VGA
Text
40 x 25
Characters
8 x 8
16 of 256K 16 of 256K
16 of 256K 16 of 256K
16 of 256K 16 of 256K
16 of 256K 16 of 256K
16 of 256K 16 of 256K
16 of 256K 16 of 256K
70
70
70
70
70
70
70
70
70
70
2, 3
VGA
Text
80 x 25
Characters
8 x 8
0*, 1*
2*, 3*
VGA
Text
40 x 25
Characters
8 x 14
8 x 14
9 x 16
9 x 16
8 x 8
VGA
Text
80 x 25
Characters
0+, 1+ VGA
Text
40 x 25
Characters
2+, 3+ VGA
Text
80 x 25
Characters
4, 5
VGA
Grph
320 x 200
Pels
4 of 256K
2 of 256K
Mono
4 of 256K
2 of 256K
Mono
6
VGA
Grph
640 x 200
Pels
8 x 8
7
VGA
Text
80 x 25
Characters
9 x 14
9 x 16
7+
VGA
Text
80 x 25
Characters
Mono
Mono
B-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Controller and Modes
Table 1: Video modes (VGA) (continued)
Video Type Resolution Character
LCD
colors
CRT
colors
Scanning
frequency
Vertical (Hz)
mode
matrix
(pels)
D
VGA
Grph
320 x 200
Pels
8 x 8
8 x 8
16 of 256K 16 of 256K
16 of 256K 16 of 256K
70
70
70
70
60
60
70
E
VGA
Grph
640 x 200
Pels
F
VGA
Grph
640 × 350
Pels
8 x 14
8 x 14
8 x 16
8 x 16
8 x 8
Mono
16 of 256K 16 of 256K
2 of 256K 2 of 256K
Mono
10
11
12
13
VGA
Grph
640 × 350
Pels
VGA
Grph
640 × 480
Pels
VGA
Grph
640 × 480
Pels
16 of 256K 16 of 256K
256 of 256K 256 of 256K
VGA
Grph
320 x 200
Pels
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-3
Display Controller and Modes
Table 2: Video modes
Resolution
LCD colors
CRT colors
Vertical
frequency (Hz)
800 x 600
256K/256K
256K/256K
60
75
85
1024 x 768
1280 x 800
1280 x 1024
1600 x 1200
256K/256K
256K/256K
256K/256K
256K/256K
256K/256K
256K/256K
60
75
85
60
75
85
60
75
85
60
75
85
1920 x 1440
2048 x 1536
256K/256K
256K/256K
60
75
60
Some modes are not supported at LCD+CRT simultaneous mode and
LCD+CRT Multi Monitor mode.
Some models only support a maximum resolution of 1024 x 768.
B-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Controller and Modes
Table 2: Video modes (continued)
Resolution
LCD colors
CRT colors
Vertical
frequency (Hz)
800 x 600
16M/16M
16M/16M
16M/16M
16M/16M
60
75
85
1024 x 768
1280 x 800
1280 x 1024
1600 x 1200
16M/16M
16M/16M
16M/16M
16M/16M
60
75
85
60
75
85
60
75
85
60
75
85
1920 x 1440
2048 x 1536
16M/16M
16M/16M
60
75
60
Some modes are not supported at LCD+CRT simultaneous mode and
LCD+CRT Multi Monitor mode.
Some models only support a maximum resolution of 1024 x 768.
User’s Manual
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Controller and Modes
Display Settings
1. You cannot move from the Settings tab of Display Properties to the
multi-monitor when you are using the display of the computer and an
external CRT display at the same time.
■ The Settings tab is displayed in the following steps;
■ Open Control Panel, click Appearance and Themes
■ Click Display
■ Select Settings tab
Display Properties Mobile Intel® 965 Express
Graphics Controller Properties
B-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Controller and Modes
®
■ The way to move to multi-monitor Intel 965 Express
■ Switch to Display Properties, like shown in previous page.
■ Click Advanced in Display Properties and choose Intel Graphics
Media Accelerator Driver for Mobile.
■ Click the Graphic Properties... button.
®
■ Select Display Devices tab in (Multiple Monitors) and Intel 965
Express Properties.
■ With external monitor connected, choose the options under Multiple
Display, then select OK.
(Multiple Monitors) and Intel® 965
Display Properties
Express Series Properties
2. In some cases DVD video playback images may not be displayed when
the display of the computer and a CRT display are used at the same.
Reduce the resolution, use the display of the computer only, use the
CRT display only or set display device in the multi-monitor, then play
DVD.
the application guide for the setting of each display device.
3. The DVD video overlay is not displayed when the display mode of CRT
display is set to high resolution and high refresh rate mode.
Please decrease the resolution and refresh rate of CRT display.
4. When the display mode is simultaneous LCD (internal liquid crystal
display) and the system goes into Standby Mode or Hibernation Mode,
you can switch to the LCD (internal liquid crystal display) display mode
by pressing Fn + F5. Under this environment, however, you may not
return to the simultaneous LCD (internal liquid crystal display) display
mode.
In these cases, perform the following steps:
®
In the Intel 965 Express Series Properties, choose the options you
want to use.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-7
Display Controller and Modes
B-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Appendix C
Wireless LAN
Card Specifications
Form Factor
Compatibility
Mini PCI TypeIII
■ IEEE 802.11 Standard for Wireless LANs
■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi
Alliance.
The "Wi-Fi CERTIFIED" logo is a certification
mark of the Wi-Fi Alliance.
®
®
■ Microsoft Windows Networking
Network Operating
System
■ CSMA/CA (Collision Avoidance) with
Media Access
Protocol
Acknowledgement (ACK)
■ 54/48/36/24/18/12/9/6 Mb/s (IEEE 802.11g)
Data Rate
■ 11/5.5/2/1 Mb/s (IEEE 802.11 b)
The Wireless LAN feature is not available on all models.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C-1
Wireless LAN
Radio Characteristics
Radio Characteristics of Wireless LAN Cards may vary according to:
■ Country/region where the product was purchased
■ Type of product
Wireless communication is often subject to local radio regulations.
Although Wireless LAN wireless networking products have been designed
for operation in the license-free 2.4GHz band, local radio regulations may
impose a number of limitations to the use of wireless communication
equipment.
Refer to the sheet "Information to the User" for regulatory information that
may apply in your country/region.
■ Band 2.4GHz (2400~2497 MHz ) for
R-F Frequency
802.11a/b/g/n specifications
■ DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK
Modulation
Technique
(IEEE 802.11b)
■ OFDM-BPSK, OFDM-QPSK, OFDM-
16QAMOFDM-16QAM ( IEEE 802.11g)
The range of the wireless signal is related to the transmit rate of the
wireless communication device. Communications at a lower transmission
rate may travel larger distances.
■ The range of your wireless devices can be affected when the antennas
are placed near metal surfaces and solid high-density materials.
■ Range is also impacted due to “obstacles” in the path of the
transmission that may either absorb or reflect the radio signal.
C-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless LAN
Supported Frequency Sub-bands
Subject to the radio regulations that apply in the countries/regions, your
Wireless LAN card may support a different set of 2.4 GHz channels.
Consult your Authorized Wireless LAN or TOSHIBA Sales office for
information about the radio regulations that apply in the countries/regions.
Wireless IEEE 802.11 Channels Sets (Revision B and G)
Frequency Range
2400-2483.5 MHz
Channel ID
1
2
3
4
5
6
7
8
9
10
2412
2417
2422
2427
2432
2437
2442
2447
2452
1
2457*
11
12
2462
2
2467*
2
13
2472*
*1 Factory-set default channels
*2 Refer to the sheet Approved Countries/Regions for use for the
countries/regions that in which these channels can be used.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C-3
Wireless LAN
When installing Wireless LAN cards, the channel configuration is managed
as follows:
■ For wireless clients that operate in a Wireless LAN Infrastructure, the
Wireless LAN card will automatically start operation at the channel
identified by the Wireless LAN Access Point. When roaming between
different access points the station can dynamically switch to another
channel if required.
■ For Wireless LAN cards installed in wireless clients that operating in a
peer-to-peer mode, the card will use the default channel 10.
■ In a Wireless LAN Access Point, the Wireless LAN card will use the
factory-set default channel (printed in bold), unless the LAN
Administrator selected a different channel when configuring the
Wireless LAN Access Point device.
C-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Appendix D
AC Power Cord and Connectors
The power cord’s AC input plug must be compatible with the various
international AC power outlets and the cord must meet the standards for
the country/region in which it is used. All cords must meet the following
specifications:
Length:
Minimum 1.7 meters
2
Wire size:
Minimum 0.75 mm
Current rating:
Voltage rating:
Minimum 2.5 amperes
125 or 250 VAC (depending on country/region’s
power standards)
Certification agencies
U.S. and Canada: UL listed and CSA certified
No. 18 AWG, Type SVT or SPT-2 two conductor
Australia:
Japan:
AS
DENANHO
Europe:
Austria:
Belgium:
Denmark:
Finland:
France:
OVE
Italy:
IMQ
CEBEC
DEMKO
SETI
The Netherlands: KEMA
Norway:
NEMKO
SEMKO
SEV
Sweden:
UTE
Switzerland:
Germany:
VDE
United Kingdom: BSI
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
AC Power Cord and Connectors
In Europe, power cords must be VDE type, H05VVH2-F and two conductor.
For the United States and Canada, plug configuration must be a 2-15P
(250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code
handbook and the Canadian Electrical Code Part II.
The following illustrations show the plug shapes for the U.S.A. and Canada,
the United Kingdom, Australia and Europe.
USA and Canada
United Kingdom
UL approved
CSA approved
BS approved
Australia
Europe
AS approved
Approved by the
appropriate agency
D-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Appendix E
Legal Footnotes
This chapter states the Legal Footnotes information applicable to TOSHIBA
computers. In the text in this manual, *XX is used to show which Legal
Footnotes description is related to TOSHIBA computers.
Description(s) related to this computer are marked with a blue *XX in this
manual. Clicking on *XX will display the related description.
Non-applicable Icons
Certain computer chassis are designed to accommodate all possible
configurations for an entire product series. Therefore, please be aware that
your selected model may not have all the features and specifications
corresponding to all of the icons or switches shown on the computer
chassis.
CPU
Central Processing Unit ("CPU") Performance Legal Footnotes.
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use of battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of computer in areas with low air pressure (high altitude >1,000
meters or >3,280 feet above sea level)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
E-1
Legal Footnotes
■ use of computer at temperatures outside the range of 5°C to 30°C (41°F
to 86°F) or >25°C (77°F) at high altitude (all temperature references are
approximate and may vary depending on the specific computer model -
please refer to your computer documentation or visit the TOSHIBA
website at www.pcsupport.toshiba.com for details).
CPU performance may also vary from specifications due to design
configuration.
Under some conditions, your computer product may automatically
shutdown. This is a normal protective feature designed to reduce the risk of
lost data or damage to the product when used outside recommended
conditions. To avoid risk of lost data, always make back-up copies of data
by periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions in your product documentation.
Contact TOSHIBA technical service and support, refer to TOSHIBA support
64-Bit Computing.
64-bit processors are designed to take advantage of 32 and 64 bit
computing.
64-bit computing requires that the following hardware and software
requirements are met:
■ 64-bit Operating System
■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System)
■ 64-bit Device drivers
■ 64-bit applications
Certain device drivers and/or applications may not be compatible with a 64-
bit CPU and therefore may not function properly. A 32-bit version of the
operating system is preinstalled on your computer unless explicitly stated
that the operating system is 64-bit.
Memory (Main System)
Part of the main system memory may be used by the graphics system for
graphics performance and therefore reduce the amount of main system
memory available for other computing activities. The amount of main
system memory allocated to support graphics may vary depending on the
graphics system, applications utilized, system memory size and other
factors. For computer's configured with 4 GB of system memory, the full
system memory space for computing activities will be considerably less and
will vary by model and system configuration.
E-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal Footnotes
Battery Life
Battery life may vary considerably depending on product model,
configuration, applications, power management settings and features
utilized, as well as the natural performance variations produced by the
design of individual components. Published battery life numbers are
achieved on select models and configurations tested by TOSHIBA at the
time of publication. Recharge time varies depending on usage. Battery may
not charge while computer is consuming full power.
After going through many charge and discharge cycles, the battery will lose
its ability to perform at maximum capacity and will need to be replaced.
This is a normal phenomenon for all batteries. To purchase a new battery
pack, see the accessories information that is shipped with your computer.
Hard Disk Drive (HDD) Capacity
1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The
computer operating system, however, reports storage capacity using
powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and
therefore shows less storage capacity. Available storage capacity will also
be less if the product includes one or more pre-installed operating systems,
such as Microsoft Windows and/or pre-installed software applications, or
media content. Actual formatted capacity may vary.
LCD
Over a period of time, and depending on the usage of the computer, the
brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.
Maximum brightness is only available when operating in AC power mode.
The screen will dim when the computer is operated on battery power and
you may not be able to increase the brightness of the screen.
Graphics Processor Unit ("GPU")
Graphics processor unit ("GPU") performance may vary depending on
product model, design configuration, applications, power management
settings and features utilized. GPU performance is only optimized when
operating in AC power mode and may decrease considerably when
operating in battery power mode.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
E-3
Legal Footnotes
Wireless LAN
The transmission speed over the wireless LAN and the distance over which
wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
[54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g)
standard.] The actual transmission speed will be lower than the theoretical
maximum speed.
Copy Protection
Applicable copy protection standards included in certain media may
prevent or limit recording or viewing of the media.
Images
All images are simulated for purposes of illustration.
E-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA Satellite U300 / Satellite Pro U300 / PORTEGE M600 / TECRA M8 Series
Glossary
The terms in this glossary cover topics related to this manual. Alternate
naming is included for reference.
Abbreviations
AC: alternating current
AGP: accelerated graphics port
ANSI: American National Standards Institute
APM: advanced power manager
ASCII: American Standard Code for Information Interchange
BIOS: basic input output system
CD-ROM: Compact Disc-Read Only Memory
CD-RW: Compact Disc-Read/Write
CMOS: complementary metal-oxide semiconductor
CPU: central processing unit
CRT: cathode ray tube
DC: direct current
DDC: display data channel
DMA: direct memory access
DOS: disk operating system
DVD: digital versatile disc
ECP: extended capabilities port
FIR: fast infrared
HDD: hard disk drive
IDE: integrated drive electronics
I/O: input/output
IrDA: Infrared Data Association
IRQ: interrupt request
KB: kilobyte
LCD: liquid crystal display
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-1
Glossary
LED: light emitting diode
LSI: large scale integration
®
MS-DOS: Microsoft disk Operating System
OCR: optical character recognition (reader)
PCB: printed circuit board
PCI: peripheral component interconnect
RAM: random access memory
RGB: red, green, and blue
ROM: read only memory
RTC: real time clock
SCSI: small computer system interface
SIO: serial input/output
SXGA+: super extended graphics array plus
TFT: thin-film transistor
UART: universal asynchronous receiver/transmitter
USB: Universal Serial Bus
UXGA: ultra extended graphics array
VESA: Video Electronic Standards Association
VGA: video graphics array
VRT: voltage reduction technology
XGA: extended graphics array
A
adaptor: A device that provides an interface between two dissimilar
electronic devices. For example, the AC adaptor modifies the power
from a wall outlet for use by the computer. This term also refers to
the add-in circuit cards that control external devices, such as video
monitors and magnetic tape devices.
allocate: To assign a space or function for a specific task.
alphanumeric: Keyboard characters including letters, numbers and other
symbols, such as punctuation marks or mathematical symbols.
alternating current (AC): Electric current that reverses its direction of flow
at regular intervals.
analog signal: A signal whose characteristics such as amplitude and
frequency vary in proportion to (are an analog of) the value to be
transmitted. Voice communications are analog signals.
ANSI: American National Standards Institute. An organization established
to adopt and define standards for a variety of technical disciplines.
For example, ANSI defined the ASCII standard and other
information processing requirements.
antistatic: A material used to prevent the buildup of static electricity.
Glossary-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
application: A group of programs that together are used for a specific task
such as accounting, financial planning, spread sheets, word
processing and games.
ASCII: American Standard Code for Information Interchange. ASCII code is
a set of 256 binary codes that represent the most commonly used
letters, numbers, and symbols.
async: Short for asynchronous.
asynchronous: Lacking regular time relationship. As applied to computer
communications, asynchronous refers to the method of transmitting
data that does not require a steady stream of bits to be transmitted
at regular time intervals.
B
backup: A duplicate copy of files kept as a spare in case the original is
destroyed.
batch file: A file that can be executed from the system prompt containing a
sequence of operating system commands or executable files.
binary: The base two number system composed of zeros and ones (off or
on), used by most digital computers. The right-most digit of a binary
number has a value of 1, the next a value of 2, then 4, 8, 16, and so
on. For example, the binary number 101 has a value of 5. See also
ASCII.
BIOS: Basic Input Output System. The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from "binary digit," the basic unit of information used by the
computer. It is either zero or one. Eight bits is one byte. See also
byte.
board: A circuit board. An internal card containing electronic components,
called chips, which perform a specific function or increase the
capabilities of the system.
boot: Short for bootstrap. A program that starts or restarts the computer.
The program reads instructions from a storage device into the
computer's memory.
bps: Bits per second. Typically used to describe the data transmission
speed of a modem.
buffer: The portion of the computer's memory where data is temporarily
stored. Buffers often compensate for differences in the rate of flow
from one device to another.
bus: An interface for transmission of signals, data or electric power.
byte: The representation of a single character. A sequence of eight bits
treated as a single unit; also the smallest addressable unit within the
system.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-3
Glossary
C
cache memory: High speed memory which stores data that increases
processor speed and data transfer rate. When the CPU reads data
from main memory, it stores a copy of this data in cache memory.
The next time the CPU needs that same data, it looks for it in the
cache memory rather than the main memory, which saves time. The
computer has two cache levels. Level one is incorporated into the
processor and level two resides in external memory.
capacity: The amount of data that can be stored on a magnetic storage
device such as a hard disk. It is usually described in terms of
kilobytes (KB), where one KB = 1024 bytes and megabytes (MB),
where one MB = 1024 KB.
card: Synonym for board. See board.
CardBus: An industry standard bus for 32-bit PC Cards.
CD-ROM: A Compact Disc-Read Only Memory is a high capacity disc that
can be read from but not written to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read data from the disc.
CD-R: A Compact Disc-Recordable disc can be written once and read
many times. See also CD-ROM.
CD-RW: A Compact Disc-Read/Write disc can be rewritten many times.
See also CD-ROM.
character: Any letter, number, punctuation mark, or symbol used by the
computer. Also synonymous with byte.
chassis: The frame containing the computer.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output functions and controlling other
chips.
CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit
fabricated on a silicon wafer that requires very little power.
Integrated circuits implemented in CMOS technology can be tightly
packaged and are highly reliable.
cold start: Starting a computer that is currently off (turning on the power).
COM1, COM2, COM3 and COM4: The names assigned to the serial and
communication ports.
commands: Instructions you enter at the terminal keyboard that direct the
actions of the computer or its peripheral devices.
communications: The means by which a computer transmits and receives
data to and from another computer or device. See parallel interface;
serial interface.
compatibility: 1) The ability of one computer to accept and process data in
the same manner as another computer without modifying the data
or the media upon which it is being transferred.
2) the ability of one device to connect to or communicate with
another system or component.
components: Elements or parts (of a system) which make up the whole
(system).
Glossary-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
computer program: A set of instructions written for a computer that enable
it to achieve a desired result.
computer system: A combination of hardware, software, firmware, and
peripheral components assembled to process data into useful
information.
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and the settings that define how
your system works. You use the HW Setup program to control your
system configuration.
control keys: A key or sequence of keys you enter from the keyboard to
initiate a particular function within a program.
controller: Built-in hardware and software that controls the functions of a
specific internal or peripheral device (e.g. keyboard controller).
co-processor: A circuit built into the processor that is dedicated to
intensive math calculations.
CPS: Characters Per Second. Typically used to indicate the transmission
speed of a printer.
CPU: Central Processing Unit. The portion of the computer that interprets
and executes instructions.
CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a
fluorescent screen-producing luminous spots. An example is the
television set.
cursor: A small, blinking rectangle or line that indicates the current position
on the display screen.
D
data: Information that is factual, measurable or statistical that a computer
can process, store, or retrieve.
data bits: A data communications parameter controlling the number of bits
(binary digits) used to make up a byte. If data bits = 7 the computer
can generate 128 unique characters. If data bits = 8 the computer
can generate 256 unique characters.
DC: Direct Current. Electric current that flows in one direction. This type of
power is usually supplied by batteries.
default: The parameter value automatically selected by the system when
you or the program do not provide instructions. Also called a preset
value.
delete: To remove data from a disk or other data storage device.
Synonymous with erase.
device driver: A program that controls communication between a specific
peripheral device and the computer. The CONFIG.SYS file contains
device drivers that MS-DOS loads when you turn the computer on.
dialog box: A window that accepts user input to make system settings or
record other information.
disk drive: The device that randomly accesses information on a disk and
copies it to the computer's memory. It also writes data from memory
to the disk. To accomplish these tasks, the unit physically rotates the
disk at high speed past a read-write head.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-5
Glossary
disk storage: Storing data on magnetic disk. Data is arranged on
concentric tracks much like a phonograph record.
display: A CRT, LCD, or other image producing device used to view
computer output.
documentation: The set of manuals and/or other instructions written for
the users of a computer system or application. Computer system
documentation typically includes procedural and tutorial information
as well as system functions.
DOS: disk Operating System. See operating system.
driver: A software program, generally part of the operating system, that
controls a specific piece of hardware (frequently a peripheral device
such as a printer or mouse).
DVD-RAM: A Digital Versatile Disc Random Access Memory is a high
capacity, high performance disc that lets you store large volumes of
data. The DVD-ROM drive uses a laser to read data from the disc.
DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity,
high performance disc suitable for play back of video and other
high-density files. The DVD-ROM drive uses a laser to read data
from the disc.
E
echo: To send back a reflection of the transmitted data to the sending
device. You can display the information on the screen, or output it to
the printer, or both. When a computer receives back data it
transmitted to a CRT (or other peripheral device) and then re-
transmits the data to printer, the printer is said to echo the CRT.
erase: See delete.
escape: 1) A code (ASCII code 27), signalling the computer that what
follows are commands; used with peripheral devices such as
printers and modems.
2) A means of aborting the task currently in progress.
escape guard time: A time before and after an escape code is sent to the
modem which distinguishes between escapes that are part of the
transmitted data, and escapes that are intended as a command to
the modem.
execute: To interpret and execute an instruction.
Extended Capability Port: An industry standard that provides a data
buffer, switchable forward and reverse data transmission, and run
length encoding (RLE) support.
F
fast infrared: An industry standard that enables cableless infrared serial
data transfer at speeds of up to 4 Mbps.
file: A collection of related information; a file can contain data, programs, or
both.
firmware: A set of instructions built into the hardware which controls and
directs a microprocessor’s activities.
Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys.
Glossary-6
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
®
folder: An icon in Windows used to store documents or other folders.
format: The process of readying a blank disc for its first use. Formatting
establishes the structure of the disc that the operating system
expects before it writes files or programs onto the disc.
function keys: The keys labelled F1 through F12 that tell the computer to
perform certain functions.
G
gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also
megabyte.
graphics: Drawings, pictures, or other images, such as charts or graphs, to
present information.
H
hard disk: A non-removable disk usually referred to as drive C. The factory
installs this disk and only a trained engineer can remove it for
servicing. Also called fixed disk.
hard disk drive (HDD): An electromechanical device that reads and writes
a hard disk. See also hard disk.
hardware: The physical electronic and mechanical components of a
computer system: typically, the computer itself, external disc drives,
etc. See also software and firmware.
hertz: A unit of wave frequency that equals one cycle per second.
hexadecimal: The base 16 numbering system composed of the digits 0
through 9 and the letters A, B, C, D, E, and F.
host computer: The computer that controls, regulates, and transmits
information to a device or another computer.
hot key: The computer's feature in which certain keys in combination with
the extended function key, Fn, can be used to set system
parameters, such as speaker volume.
HW Setup: A TOSHIBA utility that lets you set the parameters for various
hardware components.
I
icon: A small graphic image displayed on the screen or in the indicator
®
panel. In Windows , an icon represents an object that the user can
manipulate.
i.LINK (IEEE1394): This port enables high-speed data transfer directly
from external devices such as digital video cameras.
input: The data or instructions you provide to a computer, communication
device or other peripheral device from the keyboard or external or
internal storage devices. The data sent (or output) by the sending
computer is input for the receiving computer.
instruction: Statements or commands that specify how to perform a
particular task.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-7
Glossary
interface: 1) Hardware and/or software components of a system used
specifically to connect one system or device to another.
2) To physically connect one system or device to another to
exchange information.
3) The point of contact between user, the computer, and the
program, for example, the keyboard or a menu.
interrupt request: A signal that gives a component access to the
processor.
I/O: Input/output. Refers to acceptance and transfer of data to and from a
computer.
I/O devices: Equipment used to communicate with the computer and
transfer data to and from it.
IrDA 1.1: An industry standard that enables cableless infrared serial data
transfer at speeds of up to 4 Mbps.
J
jumper: A small clip or wire that allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo, meaning 1000; often used as equivalent
to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
KB: See kilobyte.
keyboard: An input device containing switches that are activated by
manually pressing marked keys. Each keystroke activates a switch
that transmits a specific code to the computer. For each key, the
transmitted code is, in turn, representative of the (ASCII) character
marked on the key.
kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte
and megabyte.
L
level 2 cache: See cache.
Light Emitting Diode (LED): A semiconductor device that emits light when
a current is applied.
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of
glass coated with transparent conducting material. The viewing side
coating is etched into character forming segments with leads that
extend to the edge of the glass. Applying a voltage between the
glass sheets alters the brightness of the liquid crystal.
LSI: Large Scale Integration.
1) A technology that allows the inclusion of up to 100,000 simple
logic gates on a single chip.
2) An integrated circuit that uses large scale integration.
Glossary-8
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
M
main board: See motherboard.
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also
kilobyte.
megahertz: A unit of wave frequency that equals 1 million cycles per
second. See also hertz.
menu: A software interface that displays a list of options on the screen.
Also called a screen.
microprocessor: A hardware component contained in a single integrated
circuit that carries out instructions. Also called the central
processing unit (CPU), one of the main parts of the computer.
mode: A method of operation, for example, the boot mode, Standby Mode
or the Hibernation Mode.
modem: Derived from modulator/demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and
then converts modulated data (demodulates) to digital format where
received.
monitor: A device that uses rows and columns of pixels to display
alphanumeric characters or graphic images. See also CRT.
motherboard: A name sometimes used to refer to the main printed circuit
board in processing equipment. It usually contains integrated
circuits that perform the processor’s basic functions and provides
connectors for adding other boards that perform special functions.
Sometimes called a main board.
MP3: An audio compression standard that enables high-quality
transmission and real-time playback of sound files.
N
nonvolatile memory: Memory, usually read-only (ROM), that is capable of
permanently storing information. Turning the computer's power off
does not alter data stored in nonvolatile memory.
numeric keypad overlay: A feature that allows you to use certain keys on
the keyboard to perform numeric entry, or to control cursor and page
movement.
O
OCR: Optical Character Recognition (reader). A technique or device that
uses laser or visible light to identify characters and input them into a
storage device.
online state: A functional state of a peripheral device when it is ready to
receive or transmit data.
operating system: A group of programs that controls the basic operation
of a computer. Operating system functions include interpreting
programs, creating data files, and controlling the transmission and
receipt (input/output) of data to and from memory and peripheral
devices.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-9
Glossary
output: The results of a computer operation. Output commonly indicates
data.
1) printed on paper, 2) displayed at a terminal, 3) sent through the
serial port of internal modem, or 4) stored on some magnetic media.
P
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on or off; odd or even; 0 or 1.
2) In serial communications, an error detection bit that is added to a
group of data bits making the sum of the bits even or odd. Parity can
be set to none, odd, or even.
password: A unique string of characters used to identify a specific user.
The computer provides various levels of password protection such
as user, supervisor and eject.
pel: The smallest area of the display that can be addressed by software.
Equal in size to a pixel or group of pixels. See pixel.
peripheral component interconnect: An industry standard 32-bit bus.
peripheral device: An I/O device that is external to the central processor
and/or main memory such as a printer or a mouse.
pixel: A picture element. The smallest dot that can be made on a display or
printer. Also called a pel.
®
plug and play: A capability with Windows that enables the system to
automatically recognize connections of external devices and make
the necessary configurations in the computer.
port: The electrical connection through which the computer sends and
receives data to and from devices or other computers.
printed circuit board (PCB): A hardware component of a processor to
which integrated circuits and other components are attached. The
board itself is typically flat and rectangular, and constructed of
fiberglass, to form the attachment surface.
program: A set of instructions a computer can execute that enables it to
achieve a desired result. See also application.
prompt: A message the computer provides indicating it is ready for or
requires information or an action from you.
R
Radio frequency interference (RFI) shield: A metal shield enclosing the
printed circuit boards of the printer or computer to prevent radio and
TV interference. All computer equipment generates radio frequency
signals. The FCC regulates the amount of signals a computing
device can allow past its shielding. A Class A device is sufficient for
office use. Class B provides a more stringent classification for home
equipment use. TOSHIBA portable computers comply with Class B
computing device regulations.
Random Access Memory (RAM): High speed memory within the
computer circuitry that can be read or written to.
restart: Resetting a computer without turning it off (also called "warm boot"
or "soft reset"). See also boot.
Glossary-10
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
RGB: Red, green, and blue. A device that uses three input signals, each
activating an electron gun for a primary additive color (red, green,
and blue) or port for using such a device. See also CRT.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
ROM: Read Only Memory: A nonvolatile memory chip manufactured to
contain information that controls the computer's basic operation.
You cannot access or change information stored in ROM.
S
SCSI: Small Computer System Interface is an industry standard interface
for connection of a variety of peripheral devices.
serial communications: A communications technique that uses as few as
two interconnecting wires to send bits one after another.
serial interface: Refers to a type of information exchange that transmits
information sequentially, one bit at a time. Contrast: Parallel
interface.
SIO: Serial Input/Output. The electronic methodology used in serial data
transmission.
soft key: Key combinations that emulate keys on the IBM keyboard,
change some configuration options, stop program execution, and
access the numeric keypad overlay.
software: The set of programs, procedures and related documentation
associated with a computer system. Specifically refers to computer
programs that direct and control the computer system’s activities.
See also hardware.
stop bit: One or more bits of a byte that follow the transmitted character or
group codes in asynchronous serial communications.
subpixel: Three elements, one red, one green and blue (RGB), that make
up a pixel on the color LCD. The computer sets subpixels
independently, each may emit a different degree of brightness. See
also pixel.
synchronous: Having a constant time interval between successive bits,
characters or events.
system disk: A disk that has been formatted with an operating system.
For MS-DOS the operating system is contained in two hidden files
and the COMMAND.COM file. You can boot a computer using a
system disk. Also called an operating system disk.
T
terminal: A typewriter-like keyboard and CRT display screen connected to
the computer for data input/output.
TFT display: A liquid crystal display (LCD) made from an array of liquid
crystal cells using active-matrix technology with thin film transistor
(TFT) to drive each cell.
TouchPad: A pointing device integrated into the TOSHIBA computer palm
rest.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-11
Glossary
TTL: Transistor-transistor logic. A logic circuit design that uses switching
transistors for gates and storage.
U
Universal Serial Bus: This serial interface lets you communicate with
several devices connected in a chain to a single port on the
computer.
V
VGA: Video Graphics Array is an industry standard video adaptor that lets
you run any popular software.
volatile memory: Random access memory (RAM) that stores information
as long as power is supplied to the computer.
W
warm start: Restarting or resetting a computer without turning it off.
window: A portion of the screen that can display its own application,
®
document or dialog box. Often used to mean a Microsoft
®
Windows window.
Glossary-12
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Power
K
emulating keys on
shut Down mode (Boot
®
Windows special keys, 5-5
temporarily using normal
Problems
on), 5-7
L
Hardware and system
M
overheating power down,
Support from TOSHIBA,
P
R
Index-2
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
S
Security lock
Soft keys
emulating keys on
keyboard, 5-2
Standby
T
U
V
W
Wireless communication switch,
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index-3
Index
Index-4
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|