Satellite® A110/A115 Series
Resource Guide
Keep this guide in a convenient place to access important
information about your computer.
If you need assistance:
❖
❖
Toshiba’s Support Web site
pcsupport.toshiba.com
Toshiba Global Support Centre
Calling within the United States (800) 457-7777
Calling from outside the United States (949) 859-4273
Please fill in for your reference and future use:
Model name______________________________________
Part number______________________________________
Serial number____________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Handling the cord on this product will expose you to lead, a chemical known
to the State of California to cause birth defects or other reproductive harm.
Wash hands after handling.
Model: Satellite® A110/A115 Series
Recordable and/or ReWritable Drive(s) and
Associated Software Warranty
The computer system you purchased may include Recordable and/or
ReWritable optical media drive(s) and associated software, among the most
advanced data storage technologies available. As with any new technology,
you must read and follow all set-up and usage instructions in the applicable
user guides and/or manuals enclosed or provided electronically. If you fail
to do so, this product may not function properly and you may lose data or
suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS,
INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT
WARRANT THAT OPERATION OF THE PRODUCT WILL BE
UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA,
ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR
REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING
FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY THEREOF.
Protection of Stored Data
For your important data, please make periodic back-up copies of all the
data stored on the hard disk or other storage devices as a precaution against
possible failures, alteration, or loss of the data. IF YOUR DATA IS
ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR
MALFUNCTION OF THE HARD DISK DRIVE OR OTHER
STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED,
TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS
OF DATA, OR ANY OTHER DAMAGE RESULTING
THEREFROM. WHEN COPYING OR TRANSFERRING YOUR
DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA
HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED.
TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO
COPY OR TRANSFER THE DATA CORRECTLY.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Critical Applications
The computer you have purchased is not designed for any “critical
applications.” “Critical applications” means life support systems, medical
applications, connections to implanted medical devices, commercial
transportation, nuclear facilities or systems or any other applications where
product failure could lead to injury to persons or loss of life or catastrophic
property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES
AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY
ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN
ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER
PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT
TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.
FCC Notice “Declaration of Conformity
Information”
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
❖
❖
❖
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
❖
Consult the dealer or an experienced radio/TV technician for help.
Only Peripherals complying with the FCC Class B limits may be attached to
this equipment. Operation with noncompliant peripherals or peripherals not
recommended by Toshiba is likely to result in interference to radio and TV
reception. Shielded cables must be used between the external devices and
the computer's parallel port, monitor port, USB port, PS/2 port®, i.LINK®
port and microphone jack. Changes or modifications made to this equipment
not expressly approved by Toshiba or parties authorized by Toshiba could
void the user's authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
❖
❖
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Contact either:
❖
❖
Toshiba’s Support Web site at pcsupport.toshiba.com.
Or call the Toshiba Global Support Centre:
Within the United States at (800) 457-7777
Outside the United States at (949) 859-4273
Industry Canada Requirement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformé à la norme NMB-003
du Canada.
FCC requirements
The following information is pursuant to FCC CFR 47, Part 68 and refers
to internal modems.
This equipment complies with Part 68 of the FCC rules. On the bottom of
this equipment is a label that contains, among other information, the FCC
registration number and ringer equivalence number (REN) for this
equipment. If requested, the information must be provided to the telephone
company.
The modem connects to the telephone line by means of a standard jack
called the USOC RJ11C.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC part 68 rules and
requirements adopted by the ACTA. It is designed to be connected to a
compatible modular jack that is also compliant.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming call. In most but
not all areas, the sum of RENs should not exceed five (5.0). To be certain of
the number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company. For products approved
after July 23, 2001, the REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX. The digits represented by the
## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation
commission for information.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it
can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations or procedures. If these changes
might affect your service or the operation of your equipment, the telephone
company will give you notice, in writing, to allow you to make any changes
necessary to maintain uninterrupted service.
If Problems Arise
If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. But if advanced notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe
it is necessary.
If trouble is experienced with this equipment, for repair or limited warranty
information, please contact Toshiba Corporation, Toshiba America
Information Systems, Inc. or an authorized representative of Toshiba, or the
Toshiba Support Centre within the United States at (800) 457-7777 or
Outside the United States at (949) 859-4273. If the equipment is causing
harm to the telephone network, the telephone company may request that
you disconnect the equipment until the problem is resolved.
Disconnection
If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device, including Fax
machines, to send any message unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of
the transmission, the date and time it is sent and an identification of the
business or other entity, or other individual sending the message and the
telephone number of the sending machine or such business, other entity, or
individual. (The telephone number provided may not be a 900 number or
Download from Www.Somanuals.com. All Manuals Search And Download.
7
any other number for which charges exceed local or long-distance
transmission charges.)
In order to program this information into your fax transmission, refer to the
fax software instructions installed on this computer.
Alarm Equipment
If your home has specially wired alarm equipment connected to the
telephone line, ensure the installation of this equipment does not disable
your alarm equipment. If you have questions about what will disable alarm
equipment, consult your telephone company or a qualified installer.
Instructions for IC CS-03 Certified Equipment
1
NOTICE: The Industry Canada label identifies certified equipment.
This certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
2
The user manual of analog equipment must contain the equipment’s
Ringer Equivalence Number (REN) and an explanation notice similar
to the following:
The Ringer Equivalence Number (REN) of this device can be found
on the label affixed to your computer.
NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
Download from Www.Somanuals.com. All Manuals Search And Download.
8
termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.
3
The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
Wireless Interoperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be
interoperable with any wireless LAN product that is based on Direct
Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:
❖
The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as
defined and approved by the Institute of Electrical and Electronics
Engineers.
❖
The Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi
Alliance. The “Wi-Fi CERTIFIED” logo is a certification mark of the
Wi-Fi Alliance.
Bluetooth® and Wireless LAN devices operate within the same radio
frequency range and may interfere with one another. If you use Bluetooth
and Wireless LAN devices simultaneously, you may occasionally
experience a less than optimal network performance or even lose your
network connection.
If you should experience any such problem, immediately turn off your Blue-
tooth or Wireless LAN device.
europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in
the United States for more information.
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 GHz
to 5.25 GHz frequency range. FCC requires this product to be used indoors
for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harm-
ful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and
5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/
or damage this device.
Wireless LAN and Your Health
Wireless LAN products, like other radio devices, emit radio frequency
electromagnetic energy. The level of energy emitted by Wireless LAN
devices however is far much less than the electromagnetic energy emitted
by wireless devices like for example mobile phones.
Because Wireless LAN products operate within the guidelines found in
radio frequency safety standards and recommendations, TOSHIBA
believes Wireless LAN is safe for use by consumers. These standards and
Download from Www.Somanuals.com. All Manuals Search And Download.
9
recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who
continually review and interpret the extensive research literature.
In some situations or environments, the use of Wireless LAN may be
restricted by the proprietor of the building or responsible representatives of
the organization. These situations may for example include:
❖
❖
Using the Wireless LAN equipment on board airplanes, or
In any other environment where the risk of interference to other
devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices
in a specific organization or environment (e.g. airports), you are
encouraged to ask for authorization to use the Wireless LAN device prior to
turning on the equipment.
Exposure to Radio Frequency Radiation
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is
far below the FCC radio frequency exposure limits. Nevertheless, the
TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that
the potential for human contact during normal operation is minimized. In
normal operating configuration, the LCD in the upright position, the dis-
tance between the antenna and the user should not be less than 20 cm. The
antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. Antenna(s) used in 5.15
GHz to 5.25 GHz frequency band must be integral antenna which provide
no access to the end user.
Refer to the Regulatory Statements as identified in the documentation that comes
with those products for additional information.
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in
strict accordance with the manufacturer’s instructions as described in the
user documentation that comes with the product. This device complies with
the following radio frequency and safety standards.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
The installer of this radio equipment must ensure that the antenna is located
or pointed such that it does not emit RF field in excess of Health Canada
limits for the general population; consult Safety Code 6, obtainable from
co-located with any other transmitter that has not been tested with this
device.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of this device.
L’utilisation de ce dispositif est autorisée seulement aux conditions
suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du
dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fonctionnement
du dispositif.
The term “IC” before the equipment certification number only signifies that
the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended
to be operated indoors and away from windows to provide maximum
shielding. Equipment (or its transmit antenna) that is installed outdoors is
subject to licensing.
Pour empecher que cet appareil cause du brouillage au service faisant
l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin
des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel
(ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet
d'une licence.
This device is restricted to indoor use due to its operation in the 5.15 GHz
to 5.25 GHz frequency range. Industry Canada requires this product to be
used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the
potential for harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and
5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with
and/or damage this device.
EU Declaration of Conformity
TOSHIBA declares, that this product conforms to the following Standards:
Supplementary *The product complies with the
Information: requirements of the Low Voltage Directive
72/23/EEC, the EMC Directive 89/336/
EEC and/or the R&TTE Directive 1999/
05/EEC.
This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe,
Hammfelddamm 8, 41460 Neuss, Germany.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
VCCI Class B Information
Modem Warning Notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR-21”]
for pan-European single terminal connection to the Public Switched
Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in the
first instance.
The above Caution information applies to products that operate with an
802.11a device.
Taiwan
Article 14 Unless approved, for any model accredited low power radio frequency electric
machinery, any company, trader or user shall not change the frequency,
increase the power or change the features and functions of the original design.
Article 17 Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event
interference is caused, the use of such electric machinery shall be immediately
discontinued. Operation of such products can be resumed only when they are
modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio
communications operated in accordance with telecommunication laws and
regulations.
Low power radio frequency electric machinery shall resist against
interference from legal communications or from industrial, scientific and
medical radio emission electric machinery.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for
second generation low-power data communication systems such as this
equipment overlaps that of mobile object identification systems (premises
radio station and specified low-power radio station).
1. Sticker
Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the
same range as industrial devices, scientific devices, medical
devices, microwave ovens, licensed radio stations and non-licensed
specified low-power radio stations for mobile object identification
systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with
any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations,
promptly change the frequency being used, change the location
of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference
caused by this product to Other Radio Stations.
2. Indication
The indication shown below appears on this equipment.
(3)
(1) (2)
2.4DSOF4
(4)
1
2
2.4: This equipment uses a frequency of 2.4 GHz.
DS: This equipment uses DS-SS modulation.
OF: This equipment uses OFDM modulation.
The interference range of this equipment is less than 40m.
3
4
This equipment uses a frequency bandwidth from
2,400 MHz to 2,483.5 MHz.
It is possible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC
Monday – Friday: 10:00 – 17:00
Toll Free Tel: 0120-13-1100
Direct Dial: 03-3457-5916
Fax: 03-5444-9450
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Device Authorization
This device obtains the Technical Regulation Conformity Certification and
the Technical Conditions Compliance Approval, and it belongs to the
device class of radio equipment of low-power data communication system
radio station stipulated in the Radio Law and the Telecommunications
Business Law of Japan.
The Name of the radio equipment: refer to the equipment label provided on
the computer
JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS
EQUIPMENT
Approval Number: D01-1128JP
TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018,
03GZDA0017
The following restrictions apply:
❖
❖
❖
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.
5.17 GHz to 5.23 GHz for indoor use only.
Radio Approvals for Wireless Devices
The following information is dependent on what type of wireless device is in
your computer.
Approved Countries/Regions for use for the Atheros
AR5BMB-43/44 and AR5BMB5 Mini PCI Wireless
Network Adapters
This equipment is approved to the radio standard by the countries/regions
in the following table.
Do not use this equipment except in the countries/regions in the following table.
This device works on passive scan only.
A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz)
Australia
Canada
France
Austria
Denmark
Germany
Italy
Belgium
Finland
Greece
Ireland
Liechtenstein
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Luxembourg
Norway
Netherlands
Portugal
UK
New Zealand
Sweden
Switzerland
USA
Europe - Restrictions for use of 2.4 GHz Frequencies in
European Community Countries
België/
Belgique:
For private usage outside buildings across public grounds over less than
300m no special registration with IBPT/BIPT is required. Registration to
IBPT/BIPT is required for private usage outside buildings across public
grounds over more than 300m. For registration and license please
contact IBPT/BIPT.
Voor privé-gebruik buiten gebouw over publieke groud over afstand
kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik
over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig.
Voor registratie of licentie kunt u contact opnemen met BIPT.
Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au-
dessus d’un espace public, aucun enregistrement n’est nécessaire pour
une distance de moins de 300m. Pour une distance supérieure à 300m un
enregistrement auprès de I’IBPT est requise. Pour les enregistrements et
licences, veuillez contacter I’IBPT.
Deutschland:
France:
License required for outdoor installations. Check with reseller for
procedure to follow.
Anmeldung im Outdoor-Bereich notwendig, aber nicht
genehmigungspflichtig.Bitte mit Händler die Vorgehensweise
abstimmen.
Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454
MHz respectively) may be used outdoors in France. Please contact
Bande de fréquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz
respectivement) doivent être utilisés endroits extérieur en France. Vous
pouvez contacter I’Autorité de Régulation des Télécommuniations
Italia:
License required for indoor use. Use with outdoor installations not
allowed.
E’necessaria la concessione ministeriale anche per l’uso interno.
Verificare con i rivenditori la procedura da seguire.
Nederland:
License required for outdoor installations. Check with reseller for
procedure to follow.
Licentie verplicht voor gebruik met buitenantennes. Neem contact op
met verkoper voor juiste procedure.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
802.11a (5 GHz)
Australia
Canada
Austria
Denmark
Germany
Italy
Belgium
Finland
France
Greece
Ireland
Liechtenstein
New Zealand
Sweden
Luxembourg
Norway
Netherlands
Portugal
UK
Switzerland
USA
Turbo Mode (5 GHz)
Canada
USA
Europe - Restrictions for Use of 5 GHz Frequencies in
European Community Countries
European Community
5150-5250 MHz 5250-5350 MHz
5470-5725 MHz
Countries
Channels: 36, 40, 44, Channels: 52, 56, 60, Channels: 100, 104, 108, 112,
48
64
116, 120, 124, 128, 132, 136, 140
Indoor Only
Indoor Only
Indoor/Outdoor
Austria
O
O
x
x
x
Belgium, France,
O
Switzerland/Lichtenstein
Denmark, Finland,
Germany, Greece,
Ireland, Italy,
O
O
O
Luxembourg,
Netherlands, Norway,
Portugal, Sweden, UK
Iceland, Spain
O
O
O
O: allowed ×: forbidden
❖
To remain in conformance with European spectrum usage laws for Wireless
LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply.
The user should use the wireless LAN utility to check the current channel of
operation. If operation is occurring outside of the allowable frequencies as
listed above, the user must cease operating the Wireless LAN at that
location and consult the local technical support staff responsible for the
wireless network.
❖
❖
The 5 GHz Turbo mode feature is not allowed for operation in any
European Community country.
This device must not be operated in ad-hoc mode using channels in the
5 GHz bands in the European Community. Ad-hoc mode provides a direct
communication between two client devices without a Wireless LAN Access
Point.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
❖
This device must be used with Access Points that have employed and
activated a radar detection feature required for European Community
operation in the 5 GHz bands. This device will operate under the control of
the Access Point in order to avoid operating on a channel occupied by any
radar system in the area. The presence of nearby radar operation may result
in temporary interruption of operation of this device. The Access Point’s
radar detection feature will automatically restart operation on a channel free
of radar. You may consult with the local technical support staff responsible
for the wireless network to ensure the Access Point device(s) are properly
configured for European Community operation.
Approved Countries/Regions for use for the Atheros
AR5001X Mini PCI Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions
in the following table.
Do not use this equipment except in the countries/regions in the following
table.
This device works on passive scan only.
A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz)
Australia
Canada
Austria
Denmark
Germany
Italy
Belgium
Finland
France
Greece
Ireland
Liechtenstein
New Zealand
Sweden
Luxembourg
Norway
Netherlands
Portugal
UK
Switzerland
USA
802.11a (5 GHz)
Australia
Canada
Austria
Denmark
Germany
Italy
Belgium
Finland
France
Greece
Ireland
Liechtenstein
New Zealand
Sweden
Luxembourg
Norway
Netherlands
Portugal
UK
Switzerland
USA
Turbo Mode (5 GHz)
Canada
USA
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Approved Countries/Regions for use for the Intel®
PRO/Wireless LAN 2100 3B Mini PCI Adapter
This equipment is approved to the radio standard by the countries/regions
in the following table.
Do not use this equipment except in the countries/regions in the following
table.
Argentina
Belgium
Chile
Australia
Brazil
Austria
Canada
Denmark
Germany
Ireland
Finland
France
Greece
Iceland
Japan
Italy
Liechtenstein
Netherlands
Peru
Luxembourg
New Zealand
Portugal
Sweden
Uruguay
Mexico
Norway
Singapore
Switzerland
USA
Spain
UK
Venezuela
Approved Countries/Regions for use for the Toshiba
Mini PCI Wireless LAN Card
This equipment is approved to the radio standard by the countries/regions
in the following table.
Do not use this equipment except in the countries/regions in the following
table.
Australia
Canada
Austria
Belgium
Finland
Denmark
Germany
Iceland
France
Greece
Hong Kong
Italy
Ireland
Japan
Liechtenstein
Netherlands
Philippines
Spain
Luxembourg
New Zealand
Portugal
Sweden
UK
Malaysia
Norway
Singapore
Switzerland
USA
Thailand
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Approved Countries/Regions for use for the
INPROCOMM IPN2220 Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions
in the following table.
Do not use this equipment except in the countries/regions in the following
table.
EU
Canada
Japan
USA
Australia
New Zealand
Bluetooth® Wireless Technology
Interoperability
Bluetooth® Cards from TOSHIBA are designed to be interoperable with
any product with Bluetooth wireless technology that is based on Frequency
Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:
❖
Bluetooth Specification as defined and approved by The Bluetooth
Special Interest Group.
❖
Logo certification with Bluetooth wireless technology as defined by
The Bluetooth Special Interest Group.
Bluetooth wireless technology is a new innovative technology, and
TOSHIBA has not confirmed compatibility of its Bluetooth products with all
PCs and/or equipment using Bluetooth wireless technology other than
TOSHIBA portable computers.
Always use Bluetooth cards from TOSHIBA in order to enable wireless net-
works over two or more (up to a total of seven) TOSHIBA portable comput-
ers using these cards. Please contact TOSHIBA PC product support on Web
Europe or pcsupport.toshiba.com in the United States for more information.
When you use Bluetooth cards from TOSHIBA close to 2.4 GHz Wireless
LAN devices, Bluetooth transmissions might slow down or cause errors. If
you detect certain interference while you use Bluetooth cards from
TOSHIBA, always change the frequency, move your PC to the area outside
of the interference range of 2.4 GHz Wireless LAN devices (40 meters/
43.74 yards or more) or stop transmitting from your PC. Please contact
computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the
United States for more information.
Bluetooth and Wireless LAN devices operate within the same radio frequency
range and may interfere with one another. If you use Bluetooth and Wireless LAN
devices simultaneously, you may occasionally experience a less than optimal
network performance or even lose your network connection. If you should
experience any such problem, immediately turn off either one of your Bluetooth or
Wireless LAN. Please contact Toshiba PC product support on Web site http://
pcsupport.toshiba.com in the United States for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Bluetooth® Wireless Technology and Your Health
The products with Bluetooth® wireless technology, like other radio devices,
emit radio frequency electromagnetic energy. The level of energy emitted
by devices with Bluetooth wireless technology however is far much less
than the electromagnetic energy emitted by wireless devices like for
example mobile phones.
Because products with Bluetooth wireless technology operate within the
guidelines found in radio frequency safety standards and recommendations,
TOSHIBA believes Bluetooth wireless technology is safe for use by
consumers. These standards and recommendations reflect the consensus of
the scientific community and result from deliberations of panels and
committees of scientists who continually review and interpret the extensive
research literature.
In some situations or environments, the use of Bluetooth wireless
technology may be restricted by the proprietor of the building or
responsible representatives of the organization. These situations may for
example include:
❖
Using the equipment with Bluetooth wireless technology on board
airplanes, or
❖
In any other environment where the risk of interference to other
devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices
in a specific organization or environment (e.g. airports), you are
encouraged to ask for authorization to use the device with Bluetooth
wireless technology prior to turning on the equipment.
Exposure to Radio Frequency Radiation
The radiated output power of the Bluetooth Card from TOSHIBA is far below
the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card
from TOSHIBA shall be used in such a manner that the potential for human
contact during normal operation is minimized.
In order to comply with FCC radio-frequency radiation exposure guidelines
for an uncontrolled environment, the Bluetooth Card from TOSHIBA has to
be operated while maintaining a minimum body to antenna distance of 20
cm.
Refer to the Regulatory Statements as identified in the documentation that
comes with those products for additional information.
The Bluetooth Card from TOSHIBA is far below the FCC radio frequency
exposure limits.
Nevertheless, it is advised to use the Bluetooth Card from TOSHIBA in such a
manner that human contact during normal operation is minimized.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Regulatory statements
This product complies with any mandatory product specification in any
country/region where the product is sold. In addition, the product complies
with the following:
European Union (EU) and EFTA
This equipment complies with the R&TTE directive 1999/5/EC and has
been provided with the CE mark accordingly.
Canada — Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Taiwan
Article 14
Unless approved, for any model accredited low power radio frequency
electric machinery, any company, trader or user shall not change the
frequency, increase the power or change the features and functions of the
original design.
Article 17
Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event
interference is caused, the use of such electric machinery shall be
immediately discontinued. Operation of such products can be resumed
only when they are modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio
communications operated in accordance with telecommunication laws and
regulations.
Low power radio frequency electric machinery shall resist against
interference from legal communications or from industrial, scientific and
medical radio emission electric machinery.
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for
second generation low-power data communication systems such as this
equipment overlaps that of mobile object identification systems (premises
radio station and specified low-power radio station).
Download from Www.Somanuals.com. All Manuals Search And Download.
21
1. Sticker
Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the
same range as industrial devices, scientific devices, medical
devices, microwave ovens, licensed radio stations and non-licensed
specified low-power radio stations for mobile object identification
systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with
any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations,
promptly change the frequency being used, change the location
of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference
caused by this product to Other Radio Stations.
2. Indication
The indication shown below appears on this equipment.
(3)
(1) (2)
2.4FH1
(4)
1
2
2.4: This equipment uses a frequency of 2.4 GHz.
FH: This equipment uses FH-SS modulation.
3
4
The interference range of this equipment is less than 10m.
This equipment uses a frequency bandwidth from 2,400 MHz to
2,483.5 MHz. It is impossible to avoid the band of mobile object
identification systems.
3. TOSHIBA Direct PC
Monday – Friday: 10:00 – 17:00
Toll Free Tel: 0120-13-1100
Direct Dial: 03-3457-5916
Fax: 03-5444-9450
Device Authorization
This device obtains the Technical Regulation Conformity Certification, and
it belongs to the device class of radio equipment of low-power data
communication system radio station stipulated in the Radio Law of Japan.
The Name of the radio equipment: EYXF2CS
TELECOM ENGINEERING CENTER
Approval Number: 01NYDA1305
Download from Www.Somanuals.com. All Manuals Search And Download.
22
The following restrictions apply:
❖
❖
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.
Optical Drive Safety Instructions
The HD DVD-ROM and multi-function drives employ a laser system. To
ensure proper use of this product, please read this instruction manual
carefully and retain for future reference.
Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive,
CD-RW drive, Multi-drive or any other optical drive. You could damage the drive.
You would also be exposed to laser light or other safety hazards, resulting in
serious injury. Always contact an authorized Toshiba service provider, if any repair
or adjustment is required.
Location of the Required Label
(Sample shown below. Location of the label and manufacturing
information may vary.)
This appliance contains a laser system and is classified as a CLASS 1 LASER
PRODUCT. To use this model properly, read the user’s guide carefully and keep it
for your future reference.
Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive,
CD-RW drive, Multi-drive or any other optical drive. You could damage the drive.
You would also be exposed to laser light or other safety hazards, resulting in
serious injury. Always contact an authorized Toshiba service provider, if any repair
or adjustment is required.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Copyright
This guide is copyrighted by Toshiba America Information Systems, Inc.
with all rights reserved. Under the copyright laws, this guide cannot be
reproduced in any form without the prior written permission of Toshiba. No
patent liability is assumed, however, with respect to the use of the
information contained herein.
©2006 by Toshiba America Information Systems, Inc. All rights reserved.
Export Administration Regulation
This document contains technical data that may be controlled under the
U.S. Export Administration Regulations, and may be subject to the
approval of the U.S. Department of Commerce prior to export. Any export,
directly or indirectly, in contravention of the U.S. Export Administration
Regulations is prohibited.
Notice
The information contained in this manual, including but not limited to any
product specifications, is subject to change without notice.
TOSHIBA CORPORATION AND TOSHIBA AMERICA
INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO
WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER
INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO
ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY
FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY
FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR
OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES
BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT
SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES,
WHETHER BASED ON TORT, CONTRACT OR OTHERWISE,
ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR
ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Trademarks
Satellite is a registered trademark of Toshiba America Information
Systems, Inc. and/or Toshiba Corporation.
Microsoft and Windows are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
DirectX, Active Desktop, DirectShow, and Windows Media are registered
trademarks of Microsoft Corporation.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or
registered trademarks of Intel Corporation or its subsidiaries in the United
States and other countries.
TouchPad is a trademark of Synaptics, Inc.
Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and
any use of such marks by Toshiba is under license. Other trademarks and
trade names are those of their respective owners.
All other brand and product names are trademarks or registered trademarks
of their respective companies.
Computer Disposal Information
This product contains mercury. Disposal of this material may be regulated
due to environmental considerations. For disposal, reuse or recycling
information, please contact your local government or the Electronic
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
25
Introduction
Welcome to the world of powerful and portable multimedia
computers!
Some software may differ from its retail version (if available),
and may not include user manuals or all program functionality.
This guide
This guide offers important information about your computer,
including solutions to the most common problems, and
features and specifications.
For more detailed information, descriptions of other features,
and more extensive troubleshooting guidelines, see the
electronic user’s guide preinstalled on your system. It is also
available on the Web at pcsupport.toshiba.com.
Safety icons
This guide contains safety instructions that must be observed
in order to avoid potential hazards that could result in
personal injuries, damage to your equipment, or loss of data.
These safety cautions have been classified according to the
seriousness of the risk, and icons highlight these instructions
as follows:
Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Provides important information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
26
Other icons used
Additional icons highlight other helpful or educational
information:
TECHNICAL NOTE: This icon highlights technical information about
the computer.
HINT: This icon denotes helpful hints and tips.
DEFINITION: This icon indicates the definition of a term used in the
text.
Other documentation
Your computer comes with the following documentation in
addition to this resource guide:
❖
❖
An electronic version of the user’s guide.
It may also contain guides for other programs that may
come with your system.
For accessory information, visit Toshiba’s Web site at
accessories.toshiba.com.
Setting up your computer and getting started
The Toshiba Instruction Manual for Safety and Comfort, that
shipped with your computer, contains helpful information for
setting up your work environment and tips for working
comfortably throughout the day.
Precautions
Your computer is designed to provide optimum safety and
ease of use and to withstand the rigors of travel. You should
observe certain precautions to further reduce the risk of
personal injury or damage to the computer.
❖
Avoid prolonged physical contact with the underside or
surface of the computer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
27
Never allow any liquids to spill into any part of your computer, and
never expose the computer to rain, water, seawater or moisture.
Exposure to liquid or moisture can cause electric shock or fire,
resulting in damage or serious injury. If any of these eventualities
should accidentally occur, immediately:
1. Turn off the computer.
2. Disconnect the AC adaptor from the power plug socket and com-
puter.
3. Remove the battery pack.
Failure to follow these instructions could result in serious injury or
permanent damage to the computer.
Do not turn on the power again until you have taken the computer to
an authorized service center.
PC base and palm rest can become hot! Avoid prolonged contact to
prevent heat injury to skin.
Read the enclosed Instruction Manual for Safety and Comfort.
Never place a heavy object on the computer and be careful not to
drop a heavy object onto the computer. It could damage the
computer or cause system failure.
Your computer’s features and specifications
Certain notebook chassis are designed to accommodate all
possible configurations for an entire product Series. Your
select model may not have all the features and specifications
corresponding to all of the icons or switches shown on the
notebook chassis, unless you have selected all those features.
This information applies to all the features and icons
described in this guide.
Below are examples of some of the many possible icons used
on your computer:
(Sample Illustration) System icons
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
28
Connecting to a power source
Your computer requires power to operate. Use the power
cord/cable and AC adaptor to connect the computer to a live
electrical outlet, or to charge the computer’s battery.
Never pull on a power cord/cable to remove a plug from a socket.
Always grasp the plug directly. Failure to follow this instruction may
damage the cord/cable, and/or result in a fire or electric shock,
possibly resulting in serious injury.
Always confirm that the power plug (and extension cable plug if
used) has been fully inserted into the socket to ensure a secure
electrical connection. Failure to do so may result in a fire or electric
shock, possibly resulting in serious injury.
Be careful if you use a multiple connector. An overload on one socket
could cause a fire or electric shock, possibly resulting in serious
injury.
Always use the TOSHIBA AC adaptor that was provided with your PC
and the TOSHIBA Battery Charger (that may have been provided with
your PC), or use the AC adaptors and battery chargers specified by
TOSHIBA to avoid any risk of fire or other damage to the PC. Use of
an incompatible AC adaptor or battery charger could cause fire or
damage to the PC, possibly resulting in serious injury. TOSHIBA
assumes no liability for any damage caused. by use of an
incompatible adaptor or charger.
AC adaptor
Power cord/cable
AC adaptor cord
(Sample Illustration) Power cord/cable and AC adaptor
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
29
To connect AC power to the computer:
Connect the power cord/cable to the AC adaptor.
1
(Sample Illustration) Connecting the power cord/cable to the AC
adaptor
Handling the cord on this product will expose you to lead, a
chemical known to the State of California to cause birth defects or
other reproductive harm. Wash hands after handling.
_
+
2
Plug the AC adaptor into the DC-IN on the back of the
computer.
(Sample Illustration) Connecting the AC adaptor to the computer
3
Connect the power cord/cable to a live electrical outlet.
The AC power light on the indicator panel glows blue.
Never attempt to connect or disconnect a power plug with wet hands.
Failure to follow this instruction could result in an electric shock,
possibly resulting in serious injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
30
Connecting a printer
Your printer documentation may require you to install the printer
software before physically connecting the printer to your computer. If
you do not install the software as instructed by the printer
manufacturer, the printer may not function correctly.
Read the documentation that came with your printer. Follow the
manufacturer’s instructions when connecting a printer.
You can connect a USB-compatible printer to your computer
through one of the USB ports. To determine if the printer is
USB-compatible, check its documentation.
To make the connection, you need a suitable USB cable,
which may come with your printer. If a USB cable was not
included with your printer, you can purchase one from a
computer or electronics store.
If your printer supports Plug and Play, your computer will
automatically recognize the printer; the printer is then ready
for use. Refer to your printer documentation for further
instructions.
TECHNICAL NOTE: To determine if your printer supports Plug and
Play, check its documentation.
If your printer does not support Plug and Play, you must set
up the printer as described in “Setting up a printer” in the
electronic user’s guide.
To connect a USB printer to your computer:
1
Connect the printer cable to the printer and then connect
the other end to one of the computer’s USB ports.
2
Plug the printer’s power cable into a live electrical outlet.
See your printer documentation for additional configuration
steps, or see “Setting up a printer” in the electronic user’s
guide.
Installing additional memory (optional)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
31
Your computer comes with enough memory to run most of
today’s popular applications. You may want to increase the
computer’s memory if you use complex software or process
large amounts of data.
For more information on memory options, check the
accessories information that came with your computer, or
visit accessories.toshiba.com.
Additional memory modules can be installed in the memory
module slots on the base of the computer. You will need a
small Phillips screwdriver for this procedure.
If you use the computer for a long time, the memory module will
become hot. If this happens, let the module cool to room temperature
before you replace it.
To avoid damaging the computer’s screws, use a small Phillips
screwdriver that is in good condition.
Installing a memory module with the computer’s power on may
damage the computer, the module, or both.
The computer has two memory module slots — Slot A and
Slot B. You can install one or two memory modules.
Before you install or remove a memory module, turn off the computer
using the Start menu (as shown in step 1 below). If you install or
remove a memory module while the computer is in Standby or
Hibernation mode, data will be lost.
If the computer is on, begin at step 1; otherwise, skip to step 3.
1
Click Start, then Turn off computer or Shut Down
(depending on the system).
The Turn off computer or Shut Down window appears.
2
Click Turn Off or Shut Down.
The operating system turns off the computer.
3
4
Unplug and remove any cables connected to the
computer, including the AC adaptor.
Remove the main battery. For information on removing
the main battery, see “Removing the battery from the
computer” on page 47).
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
32
5
Close the display panel and turn the computer upside
down to locate the memory module slot cover.
Memory module slot cover
Front of computer
(Sample Illustration) Locating the memory module slot cover
6
Using a small Phillips screwdriver, unscrew the screw
that secures the memory module slot cover.
Front of computer
(Sample Illustration) Unscrewing the memory module slot cover
7
8
Remove the memory module slot cover.
Place the screw and the cover in a safe place so that you
can retrieve them later.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
33
Static electricity can damage the memory module. Before you handle
the module, touch a grounded metal surface to discharge any static
electricity you may have built up.
Avoid touching the connector on the memory module or on the
computer. Grease or dust on the connector may cause memory
access problems.
9
Carefully remove the new memory module from its
antistatic packaging, without touching its connector.
10 Locate an empty memory slot.
If no memory slot is available, you must remove a module by
performing steps 2-3 of “Removing a memory module” on page 35.
11 Pick up the memory module by its sides, avoiding any
contact with its connector. Position the module toward
the socket, aligning the connector’s notch with the
matching key in the socket.
notch
latch
connector
latch
key
(Sample Illustration) Aligning the memory module with the socket
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
34
12 Firmly press the memory module into the memory slot’s
socket at approximately a 30-degree angle (to the
horizontal surface of the computer).
(Sample Illustration) Inserting the module in the socket
13 Once the module’s connector is fully inserted into the
socket, press downward on the top edge of the module to
seat the module into the latches at the sides of the socket.
These latches should “snap” into place securely with the
corresponding cutouts in the side of the module. If the
latches and cutouts do not line up correctly, repeat step 12
above, then repeat this step.
latch
latch
(Sample Illustration) Pressing down on the memory module
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
35
Do not force the memory module into position. The
memory module should be completely inserted into the
socket and level when secured in place.
Memory slots
Front of computer
(Sample Illustration) Inserting the memory module into the slot
14 Replace the memory module slot cover and secure it
using the screw.
15 Re-insert the main battery. For information on inserting
the main battery, see “Inserting a charged battery” on
page 49.
16 Turn the computer right side up.
17 Reconnect the cables.
18 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module
installed for the computer to work.
Removing a memory module
If you need to remove a memory module:
1
Complete steps 1–8 in “Installing additional memory
(optional)” on page 30 to shut down the computer and
open the memory module slot cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your computer and getting started
36
Do not try to remove a memory module with the computer turned on.
You can damage the computer and the memory module.
Do not remove the memory module while the computer is in Standby
or Hibernation mode. The computer could hang up the next time you
turn it on and data in memory will be lost. In either of the above
cases, the Standby configuration will not be saved.
The following message appears when you turn on the power:
Warning: Resume Failure
Press Any Key to Continue
If the computer hangs up when you turn it on, perform the following:
Press the power button and hold it down for at least ten seconds,
then turn the power on again.
2
Pull the latches away from the memory module.
The memory module pops up slightly.
3
4
5
Gently lift the memory module to a 30-degree angle and
slide it out of the slot.
Replace the memory module slot cover and tighten the
screw.
Re-insert the main battery. For information on inserting
the main battery, see “Inserting a charged battery” on
page 49.
6
7
8
Turn the computer right side up.
Reconnect the cables.
Restart the computer.
TECHNICAL NOTE: You must have at least one memory module
installed for the computer to work.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your computer’s TFT display
37
Your computer’s TFT display
Small bright dots may appear on your screen display when
you turn on your PC. Your display contains an extremely
large number of thin-film transistors (TFT) and is
manufactured using high-precision technology. Any small
bright dots that may appear on your display are an intrinsic
characteristic of the TFT manufacturing technology. Over a
period of time, and depending on the usage of the computer,
the brightness of the screen will deteriorate. This is also an
intrinsic characteristic of the screen technology. When the
computer is operated on battery power, the screen will dim
and you may not be able to increase the brightness of the
screen while on battery power.
Inserting a PC Card
Before you insert a PC Card, refer to the documentation that
comes with the card to see if you need to do anything before
you insert it.
You may insert one Type I or Type II card into the computer’s
PC Card slot.
To insert a PC Card:
1
2
Locate the PC Card slot on the left side of the computer.
Insert the PC Card into the slot.
(Sample Illustration) Inserting a PC Card
3
When the card is almost all the way into the slot, push
firmly but gently to ensure a firm connection with the
computer. Do not force the card into position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing a PC Card
38
Removing a PC Card
Prepare the card for removal by right-clicking on the Safely
Remove Hardware icon on the system tray and then
selecting the PC Card device.
If the card can be removed now, the system displays Safe To
Remove Hardware.
1
2
Locate the PC Card eject button next to the PC Card slot.
Press the PC Card eject button once to pop it out slightly,
then push it in to remove the PC Card.
The PC Card ejects slightly from the slot.
3
Grasp the edges of the PC Card and slide it out of the slot.
Learning the basics
Computing tips
❖
Save your work frequently.
Your work stays in the computer’s temporary memory
until you save it to the disk. If the network you are using
goes down and you must restart your computer to
reconnect, or your battery runs out of charge while you are
working, you will lose all work since you last saved.
HINT: Some programs have an automatic save feature that you can
turn on. This feature saves your file to the hard disk at preset
intervals. See your software documentation for details.
❖
Back up your files to a removable storage media on a
regular basis. Label the backup copies clearly and store
them in a safe place.
❖
❖
Scan all new files for viruses.
Do not turn off the computer if a drive indicator light
indicates a drive is active.
The Windows® operating system records information, such as your
desktop setup, during its shutdown procedure. If you do not let the
Windows® operating system shut down normally, details such as new
icon positions may be lost.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TouchPad™
39
Using the TouchPad™
The TouchPad™, the small, smooth, square cutout located in
front of the keyboard, is sensitive to touch and enables you to
move the cursor with the stroke of a finger. Simply move
your finger on the TouchPad in the direction you would like
to move the cursor:
❖
❖
❖
❖
To move the cursor to the top of the page, push your
finger forward on the TouchPad.
To move the cursor to the bottom of the page, drag your
finger toward yourself.
To move the cursor to the right side of the page, slide
your finger across the TouchPad from left to right.
To move it to the left side, slide your finger from right to
left.
Because the TouchPad is much smaller than the display screen, moving
your cursor across the screen often means having to move your finger
several times across the TouchPad in the preferred direction.
Once you have positioned your cursor, you can click it into
place by either double-tapping the TouchPad or clicking the
control buttons.
Scrolling with the TouchPad™
There are two active regions on the TouchPad™ that allow you
to scroll as you would with any wheel device on a mouse or
trackball.
To scroll vertically, run your finger up or down along the right
edge of the TouchPad. To scroll horizontally, run your finger
along the bottom edge of the TouchPad. This feature can be
disabled or changed in the Mouse Properties dialog box.
Control buttons
When a step instructs you to click or choose an item, move
the cursor to the item, then press and release the primary
(left-hand) button. To double-click, press the primary button
twice in rapid succession. The primary button usually
corresponds to the left mouse button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optical drive
40
The function of the secondary (right-hand) button depends on
the program you are using. It usually corresponds to the right
mouse button (“right-clicking”). Check your program’s
documentation to determine whether it uses the right mouse
button.
Using the optical drive
Optical storage has become the preferred medium for
software, music, and video. Digital versatile discs (DVDs)
provide a significant increase in data storage and support
features that are not available on any other video platform.
These features include wide-screen movies, multiple
language tracks, digital surround sound, multiple camera
angles, and interactive menus.
For these reasons, your computer may come with an optical
drive.
TECHNICAL NOTE: Your optical drive is set to play region 1 (North
America) DVD-ROMs. If you play a DVD disc from another region,
the drive will automatically change to play in the format of the other
region. The drive will allow you to change regions four times. On the
fourth change, the region will be “locked in.” That is, the drive will
only play DVDs from that last region. Note that changing from region
1 to region 2 and back to region 1 is counted as two changes.
For optimum DVD performance, it is recommended that you play
DVDs while running the computer on AC power.
Your optical drive may look like this:
Drive in-use indicator light
Eject button
Manual eject hole
(Sample Illustration) Optical drive
Drive in-use indicator light—Indicates when the drive is in
use.
Eject button—Press to release the disc tray.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optical drive
41
Do not press the eject button or turn off the computer while the drive
in-use indicator light is glowing. Doing so could damage the disc or
the drive.
When the disc tray is open, be careful not to touch the lens or the
area around it. Doing so could cause the drive to malfunction.
Manual eject hole—Use if you need to release the disc tray
when the power is off. Use a straightened paper clip or other
narrow object to press the manual eject button located inside
the hole.
Never use a pencil to press the manual eject button. Pencil lead can
break off inside the computer and damage it.
Media control buttons
The media control buttons located to the right of the keyboard
let you access the Internet when the computer is on and play
audio CDs or DVD movies when the computer is off. You can
also use them to play CDs and DVDs when the computer is
on.
Power button
Internet button*
CD/DVD*
Play/Pause*
Stop*
Next track*
Previous track*
*Available on certain models.
(Sample Illustration) Media Control buttons
The Power button lets you turn the computer on or off.
The Internet button lets you access the Internet when the
computer is powered on.
The following chart describes the Internet button
functionality.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optical drive
42
Power is off or the computer is The system accesses the Internet.
in Hibernation mode and you
press the Internet button
Operating system is running or The system accesses the Internet.
the computer is in Standby
mode and you press the
Internet button
The CD/DVD button activates a media playing application
that can play audio CDs or DVD movies when the computer
is powered off.
The following chart describes the CD/DVD button
functionality.
Power is off or the computer is If a CD is in the drive, the system operates as a
in Hibernation mode and you stand-alone CD player.
press the CD/DVD button
If a DVD is in the drive, the system operates as a
stand-alone DVD movie player
Operating system is running or If a CD is in the drive, the Windows® Media
the computer is in Standby
mode and you press the CD/
DVD button
Player starts and the audio CD begins to play.
If a DVD is in the drive, WinDVD™ starts and
the DVD begins to play.
The Play/Pause button starts playing the disc or makes it
pause if currently playing.
The Stop button stops a disc that is currently playing.
The Next track button skips to the following track on the
disc.
The Previous track button returns to the preceding track on
the disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optical drive
43
Inserting a compact disc
Before putting on headphones to listen to an audio CD, turn the
volume dial down. Do not set the volume too high when using the
headphones. Continuous exposure to loud sound can harm your
hearing.
To insert a compact disc into the drive:
1
2
3
Make sure the computer is turned on.
Make sure the drive’s in-use indicator light is off.
Press the drive’s eject button.
The disc tray slides partially out of the drive (about 1 inch).
HINT: The drive will not open if the computer’s power is off.
4
5
Grasp the tray and pull it fully open.
Hold the disc by its edges and check that it is free of dust.
If the disc is dusty, clean it.
6
Place the disc carefully in the disc tray, label side up.
(Sample Illustration) Positioning the disc in the drive
7
Gently press the disc onto the center spindle until it clicks
into place.
Handle DVDs and CDs carefully, making contact only with the center
hole and edge. Do not touch the surface of the disc. Do not stack
discs. If you incorrectly handle the discs, you could lose data.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optical drive
44
8
9
Make sure the disc is completely on the spindle and is
lying flat on the tray.
If you insert the disc incorrectly, it may jam the drive. If this happens,
contact Toshiba support for assistance.
Push the disc tray in by pressing gently on the center of
the tray until it clicks into place.
You are ready to use the disc.
Removing a disc with the computer on
To remove a compact disc (CD or DVD) with the computer
turned on:
1
Press the eject button on the drive.
Do not press the eject button while the in-use indicator light is
glowing. Doing so could damage the disc or the drive.
Also, if the disc is still spinning when you open the disc tray, wait for
it to stop spinning before you remove it.
2
3
Pull the tray out until it is fully open, remove the disc,
and place it in its protective cover.
Gently push the tray in to close it.
Removing a disc with the computer off
To remove a disc with the computer turned off:
1
Insert a slender object, such as a straightened paper clip,
into the manual eject hole.
The disc tray slides partially out of the drive (about 1 inch).
Never use a pencil to press the manual eject button. Pencil lead can
break off inside the computer and damage it.
2
3
Pull the tray out until it is fully open, remove the disc,
and place it in its protective cover.
Gently push the tray in to close it.
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving the computer
45
Moving the computer
Before moving your computer, even across the room, make
sure all disk activity has ended (the drive indicator light stops
glowing) and all external peripheral cables are disconnected.
Do not pick up the computer by its display panel or by the back
(where the ports are located). Doing so could damage the system.
Mobile computing
Running the computer on battery power
Battery life may vary considerably from specifications
depending on product model, configuration, applications,
power management settings and features utilized, as well as
the natural performance variations produced by the design of
individual components. Published battery life numbers are
achieved on select models and configurations tested by
Toshiba at the time of publication. Recharge time varies
depending on usage. Battery may not charge while the
computer is consuming full power.
After a period of time, the battery will lose its ability to
perform at maximum capacity and will need to be replaced.
This is normal for all batteries. To purchase a new battery
computer or visit the Toshiba Web site at
accessories.toshiba.com. Use only batteries designed
to work with your Toshiba notebook computer.
To ensure that the battery maintains its maximum capacity,
operate the computer on battery power at least once a month
until the battery is fully discharged. Please see “Maximizing
battery life” on page 50 for procedures. If the computer is
continuously operated on AC power, either through an AC
adaptor or a docking station (if applicable to your system),
for an extended period (more than a month), the battery may
fail to retain a charge. This may shorten the life of the battery,
and the battery light may not indicate a low-battery condition.
The computer also has an internal real-time-clock (RTC)
battery.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mobile computing
46
The RTC battery powers the RTC memory that stores your
system configuration settings and the current time and date
information. It maintains this information for up to a month
while the computer is turned off.
TECHNICAL NOTE: The RTC battery does not charge while the
computer is turned off, even when AC power is attached.
The RTC battery charges only while the computer is powered on.
Monitoring main battery power
The computer’s main battery light gives you an indication of
the main battery’s current charge:
❖
Glows amber while the main battery is being charged
(AC adaptor connected)
❖
❖
Glows blue when the main battery is fully charged
Is unlit when the battery has discharged, the battery is not
charging, or the AC adaptor is not plugged into the
computer or AC outlet
Battery life and charge time may vary, depending upon power
management settings, applications and features used.
❖
Flashes amber when the main battery charge is low and it
is time to recharge the main battery or plug in the AC
adaptor
HINT: Be careful not to confuse the battery light ( ) with the on/off
light ( ). When the on/off light flashes amber, it indicates that the
system is suspended (using the Windows® operating system
Standby command).
HINT: Be careful not to confuse the battery light ( ) with the on/off
light ( ) and the power button light (near the upper left corner of
the keyboard). When the on/off light or power button light flashes
amber, it indicates that the system is suspended (using the
Windows® operating system Standby command).
Download from Www.Somanuals.com. All Manuals Search And Download.
Mobile computing
47
TECHNICAL NOTE: When your computer is using all of the power
provided by the AC Adaptor to run applications, features, and
devices, the recharging of the battery cannot occur. Your computer's
Power Saver utility can be used to select a power level setting that
reduces the power required for system operation and will allow the
battery to recharge.
Setting battery alarms
Your computer can be configured to warn you when the
battery is running low. For more information, see “Setting
battery alarms” in the electronic user’s guide.
Changing the main battery
When your main battery has run out of power, you have two
options: plug in the AC adaptor or install a fresh main battery.
Never short circuit the battery pack by either accidentally or
intentionally bringing the battery terminals in contact with another
conductive object. This could cause serious injury or fire, and could
also damage the battery pack.
❖
Never expose a battery pack to abnormal shock, vibration or
pressure. The battery pack's internal protective device could
fail, causing it to overheat or ignite, resulting in caustic liquid
leakage, or explosion or fire, possibly resulting in death or
serious injury.
Never expose a battery pack to abnormal shock, vibration or
pressure. The battery pack's internal protective device could fail,
causing it to overheat or ignite, resulting in caustic liquid leakage, or
explosion or fire, possibly resulting in death or serious injury.
TECHNICAL NOTE: To avoid losing any data, save your files and
then either completely shut down your computer, or put it into
Hibernation mode before changing the main battery.
Removing the battery from the computer
To remove the battery:
1
2
Save your work.
Turn off the computer or place it in Hibernation mode
according to the instructions in “Using and configuring
Hibernation mode” in the electronic user’s guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mobile computing
48
3
4
5
Unplug and remove any cables connected to the
computer, including the AC adaptor.
Close the display panel and turn the computer upside
down.
Slide the battery release lock to the unlocked position.
(Sample Illustration) Unlocking the battery release lock
6
7
Slide the battery release latch to release the battery.
Pull the discharged battery out of the computer.
(Sample Illustration) Removing the battery
If the battery is leaking or its case is cracked, put on protective gloves
to handle it, and discard it immediately. Always dispose of used battery
packs in compliance with all applicable laws and regulations. Put
insulating tape, such as cellophane tape, on the electrode during
transportation to avoid a possible short circuit, fire or electric shock.
Failure to do so could possibly result in serious injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking care of your battery
49
Inserting a charged battery
To insert a battery:
1
2
Wipe the terminals of the charged battery with a clean
cloth to ensure a good connection.
Insert the charged battery into the slot until the latch clicks.
The battery has been designed so that you cannot install it
with reverse polarity.
If the battery does not slide into the slot easily, move the battery
release lock to the unlocked position and try again. Do not force the
battery into position.
3
4
5
Slide the battery lock to the locked position.
Turn the computer right side up.
Reconnect any cables that were removed in step 3 of
“Removing the battery from the computer” on page 47.
6
Restart the computer.
Taking care of your battery
The following sections offer tips on how to take care of your
battery and prolong its life.
Battery safety precautions
❖
If the battery pack produces an odor, overheats or
changes color or shape while it is being used or charged,
turn off the computer’s power immediately and
disconnect the power cord/cable from the power socket.
Carefully remove the battery pack from the computer.
❖
❖
Do not try to disassemble a battery pack.
Do not overcharge or reverse charge a battery.
Overcharging will shorten its life, and reverse charging
could damage it.
❖
❖
Avoid touching the metal terminals of the battery with
another metal object. Short-circuiting the battery can
cause it to overheat and may cause damage to the battery
or the computer.
Do not incinerate a spent battery, as this could cause it to
explode and release caustic liquid.
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking care of your battery
50
❖
❖
If a battery is leaking or damaged, replace it immediately.
Use protective gloves when handling a damaged battery.
To replace the main battery, use an identical battery that
you can purchase through the Toshiba Web site at
❖
A reverse polarity condition should be avoided with all
batteries. The main battery is designed so that it cannot
be installed in reverse polarity.
❖
❖
❖
Charge the battery only in the computer or in a battery
charger designated as an approved option.
When you install the battery pack, you should hear a
click when it is seated properly.
Do not expose the battery pack to fire. The battery pack
could explode.
Maximizing battery life
To maximize the life of your battery pack:
❖
At least once a month, disconnect the computer from a
power source and operate it on battery power until the
battery pack fully discharges. Before doing so, follow the
steps below:
1
2
Turn off the computer’s power.
Disconnect the AC adaptor and turn on the
computer’s power. If it does not turn on, go to step 4.
3
4
Operate the computer on battery power for five
minutes. If the battery pack has at least five minutes
of operating time, continue operating until the battery
pack is fully discharged. If the battery light flashes or
there is some other warning to indicate a low battery,
go to step 4.
Connect the AC adaptor to the computer and connect
the power cord/cable to a power outlet. The DC-IN or
AC power-light should glow blue, and the battery
light should glow amber to indicate that the battery
pack is being charged. If the DC-IN or AC power-
light indicator does not glow, power is not being
supplied. Check the connections for the AC adaptor
and power cord/cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking care of your battery
51
5
Charge the battery pack until the battery light glows
blue.
❖
❖
If you have extra battery packs, rotate their use.
If you will not be using the system for an extended
period, more than one month, remove the battery pack.
❖
Disconnect the AC adaptor when the battery is fully
charged. Overcharging makes the battery hot and
shortens its life.
❖
❖
If you are not going to use the computer for more than
eight hours, disconnect the AC adaptor.
Store spare battery packs in a cool dry place out of direct
sunlight.
Disposing of used batteries
When a battery pack nears the end of its life, its ability to
hold a charge will decrease. When the battery pack needs to
be replaced, the main battery light flashes amber shortly after
you have fully recharged the battery.
You must discard a battery if it becomes damaged.
Never attempt to dispose of a battery pack by burning or by throwing
it into a fire, and never allow exposure to a heating apparatus (e.g.,
microwave oven). Heat can cause a battery pack to explode and/or
release caustic liquid, both which may possibly cause serious injury.
Always dispose of used battery packs in compliance with all
applicable laws and regulations. Put insulating tape, such as
cellophane tape, on the electrode during transportation to avoid a
possible short circuit, fire or electric shock. Failure to do so could
possibly result in serious injury.
Always use the battery pack supplied as an accessory or an
equivalent battery pack specified in the User's Manual. Other battery
packs have different voltage and terminal polarities. Use of non-
conforming battery packs could generate smoke or cause fire or
rupture, possibly resulting in serious injury.
After repeated use, batteries will finally lose their ability to
hold a charge and you will need to replace them. Under
certain applicable laws, it may be illegal to dispose of old
batteries by placing them in the trash.
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
52
Please be kind to our shared environment. Check with your
local government authority for details regarding where to
recycle old batteries or how to dispose of them properly. If
you cannot find the information you need elsewhere, call
Toshiba at: (800) 457-7777.
If something goes wrong
Problems that are easy to fix
Your program stops responding.
If you are working with a program that suddenly freezes all
operations, chances are the program has stopped responding.
You can exit the failed program without shutting down the
operating system or closing other programs.
To close a program that has stopped responding:
1
Press Ctrl, Alt, and Del simultaneously (once).
The Windows Task Manager window appears.
Click the Applications tab.
2
If a program has stopped responding, the words “not
responding” appear beside its name in the list.
3
4
Select the program you want to close, then click End
Task.
Closing the failed program should allow you to continue
working. If it does not, continue with the next step.
Close the remaining programs one by one by selecting
the program name, then End Task.
To power off your computer, do one of the following:
If you are not connected to a domain server:
1
Click Start, Turn off computer.
The Turn off computer window appears.
Click Turn Off.
2
The computer turns off.
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
53
If you are connected to a domain server:
1
Click Start, Shut down.
The Shut Down window appears.
Click Shut down from the drop-down list.
Click OK.
2
3
The computer shuts down completely.
Your program performs an illegal operation.
If you receive the message, “Your program has performed an illegal
operation,” close the window and continue working. If it
happens again, record the details of the message and consult
the software manufacturer.
To record the details:
1
Click the Details button and select the text the operating
system displays.
The Details button displays information that the software
manufacturer needs to help you solve your problem.
2
3
4
5
Press Ctrl and c simultaneously to copy the text to the
clipboard.
Open Notepad (click Start, All Programs, Accessories
and then click Notepad).
Press Ctrl and v simultaneously to paste the details into
Notepad.
Add a paragraph break and type some notes describing
what you were doing when you received the message and
how the error can be reproduced.
6
Save the file and refer to it when you contact the software
manufacturer.
Problems when you turn on the computer
These problems may occur when you turn on the power.
The computer will not start.
Make sure you attached the AC adaptor and power cord/cable
properly or installed a charged battery.
Press and hold the power switch for at least 10 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
54
If you are using the AC adaptor, check that the wall outlet is
working by plugging in another device, such as a lamp.
Verify that the computer is on by looking at the on/off
indicator. If the indicator is glowing, the computer is on.
If you are using an AC adaptor, verify that the computer is
receiving power from the external power source by looking at
the AC power light. If the indicator is glowing, the computer
is connected to a live external power source.
The computer starts, but when you press a key nothing
happens.
Verify that the active program accepts text input. Try clicking
your mouse on an area where you can type text and try typing
again.
Your computer may be in Standby mode and have a software
or resource conflict. When this happens turning the power on
returns you to the problem instead of restarting the system.
To clear the condition, press Ctrl, Alt, and Del simultaneously.
Clearing the condition may get the computer running, but it
will not solve a resource conflict. Read the documentation
that came with the conflicting device and “Resolving a
hardware conflict” in your electronic user’s guide.
The keyboard produces unexpected characters.
A keypad overlay may be on. If the numlock light or cursor
control mode light is on, press Fn and F10 simultaneously to
turn off the cursor control mode light or Fn and F11
simultaneously to turn off the numlock light.
If the problem occurs when both the keypad overlays are off,
make sure the software you are using is not remapping the
keyboard. Refer to the software documentation and check
that the program does not assign different meanings to any of
the keys.
Display problems
Here are some typical display problems and their solutions:
The screen is blank.
Display Auto Off may have gone into effect. Press any key to
activate the screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
55
You may have activated the instant password feature by
pressing Fn and F1 simultaneously. If you have registered a
password, press any key, type the password and press Enter. If
no password is registered, press any key. The screen
reactivates and allows you to continue working.
If you are using the built-in screen, make sure the display
priority is not set for an external monitor. To do this, press Fn
and F5 simultaneously (once). If this does not correct the
problem, press Fn and F5 simultaneously again to return the
display priority to its previous setting.
HINT: Holding the Fn key and pressing the F5 key several times will
advance you through the display options.
If you are using an external monitor:
❖
❖
Check that the monitor is turned on.
Check that the monitor’s power cord/cable is firmly
plugged into a working power outlet.
❖
❖
❖
Check that the cable connecting the external monitor to
the computer is firmly attached.
Try adjusting the contrast and brightness controls on the
external monitor.
Press Fn and F5 simultaneously to make sure the display
priority is not set for the built-in screen.
Small bright dots appear on your TFT display when you
turn on your computer.
Small bright dots may appear on your screen display when
you turn on your PC. Your display contains an extremely
large number of thin-film transistors (TFT) and is
manufactured using high-precision technology. Any small
bright dots that may appear on your display are an intrinsic
characteristic of the TFT manufacturing technology. Over a
period of time, and depending on the usage of the computer,
the brightness of the screen will deteriorate. This is also an
intrinsic characteristic of the screen technology. When the
computer is operated on battery power, the screen will dim
and you may not be able to increase the brightness of the
screen while on battery power.
Download from Www.Somanuals.com. All Manuals Search And Download.
If something goes wrong
56
PC Card problems
PC Card checklist
❖
Make sure the card is inserted properly into the slot.
See “Using PC Cards” in the electronic user’s guide for
information about how to insert PC Cards.
❖
❖
Make sure all cables are securely connected.
Occasionally a defective PC Card slips through quality
control. If another PCMCIA-equipped computer is
available, try the card in that machine. If the card
malfunctions again, it may be defective.
Resolving PC Card problems
Here are some common problems and their solutions:
The slot appears to be dead. PC Cards that used to work
no longer work.
Check the PC Card status:
1
2
Click Start.
Click My Computer icon with the secondary button,
then click Properties.
The System Properties dialog box appears.
3
4
5
6
Click the Hardware tab.
Click the Device Manager button.
Double-click the PCMCIA adapter.
Double-click the appropriate PC Card.
The operating system displays your PC Card’s Properties
dialog box, which contains information about your PC
Card configuration and status.
The computer stops working (hangs) when you insert a
PC Card.
The problem may be caused by an I/O (input/output) conflict
between the PCMCIA socket and another device in the
system. Use Device Manager to make sure each device has its
own I/O base address. See “Fixing a problem with device
manager” in the electronic user’s guide for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you need further assistance
57
Since all PC Cards share the same socket, each card is not
required to have its own address.
If you need further assistance
If you have followed the recommendations in this section and
are still having problems, you may need additional technical
assistance. This section contains the steps to take to ask for
help.
Before you contact Toshiba
Since some problems may be related to the operating system
or the program you are using, it is important to investigate
other sources of assistance first.
Try the following before contacting Toshiba:
❖
Review the troubleshooting information in your
operating system documentation.
❖
If the problem occurs while you are running a program,
consult the program’s documentation for troubleshooting
suggestions. Contact the software company’s technical
support group for their assistance.
Detailed system specifications are available at
model number, clicking GO, and then clicking the Detailed
Specs link from the menu on the left, or just refer to the
computer documentation shipped with your product.
For the number of a Toshiba dealer near you, see ”Toshiba
voice contact” in this section.
Contacting Toshiba
If you still need help and suspect that the problem is
hardware-related, Toshiba offers a variety of resources to help
you.
Toshiba’s Technical Support Web site
software and hardware options for your computer, and for
Download from Www.Somanuals.com. All Manuals Search And Download.
Power cord/cable connectors
58
Toshiba voice contact
Before calling Toshiba, make sure you have:
❖
❖
Your computer’s serial number
The computer and any optional devices related to the
problem
❖
❖
❖
❖
Backup copies of your Windows® operating system and
all other preloaded software on your choice of media
Name and version of the program involved in the
problem along with its installation media
Information about what you were doing when the
problem occurred
Exact error messages and when they occurred
For technical support, call the Toshiba Global Support
Centre:
Within the United States at (800) 457-7777
Outside the United States at (949) 859-4273
Power cord/cable connectors
Your computer features a universal power supply you can use
worldwide. This section shows the shapes of the typical AC
power cord/cable connectors for various parts of the world.
USA and Canada
(UL and CSA
approved)
Australia
(AS approved)
Europe
(VDA and
NEMKO approved)
United Kingdom
(BS approved)
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
59
Features and specifications
This section lists the computer’s features. Numbered legal
footnotes may also be found on page 65.
Product Series1
The product specifications and configuration information are
designed for a product Series. Your particular model may not have
all the features and specifications listed or illustrated. For more
detailed information about the features and specifications on your
particular model, visit Toshiba's Web site at pcsupport.toshiba.com.
While Toshiba has made every effort at the time of publication to
ensure the accuracy of the information provided herein, product
specifications, configurations, prices, system/component/options
availability are all subject to change without notice. For the most up-
to-date product information about your computer, or to stay current
with the various computer software or hardware options, visit
Toshiba's Web site at pcsupport.toshiba.com.
Technology and processor
Processor
Intel® Core™ Solo Processor T1300
(Central Processing Unit) (1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Core™ Duo Processor T2300E
(1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Core™ Duo Processor T2300
(1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Core™ Duo Processor T2400
(1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Core™ Duo Processor T2500
(1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Core™ Duo Processor T2600
(1.66 GHz, 2 MB L2 cache, 667 MHz FSB)
Intel® Celeron® M Processor 410
(1.46 GHz, 1 MB L2 cache, 533 MHz FSB)
Intel® Celeron® M Processor 420
(1.60 GHz, 1 MB L2 cache, 533 MHz FSB)*
2
*CPU performance in your computer product may vary from
specifications under the following conditions:
- use of certain external peripheral products
- use of battery power instead of AC power
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
60
- use of certain multimedia, computer generated graphics or
video applications
- use of standard telephone lines or low speed network
connections
- use of complex modeling software, such as high end
computer aided design applications
- use of several applications or functionalities simultaneously
- use of computer in areas with low air pressure (high altitude
>1,000 meters or >3,280 feet above sea level)
- use of computer at temperatures outside the range of 5° C to
30° C (41° F to 86° F) or >25° C (77° F) at high altitude (all
temperature references are approximate and may vary
depending on the specific computer model – please refer to
your Resource Guide, or visit the Toshiba website at
*CPU performance may also vary from specifications due
to design configuration.
Under some conditions, your computer product may
automatically shut-down. This is a normal protective feature
designed to reduce the risk of lost data or damage to the product
when used outside recommended conditions. To avoid risk of
lost data, always make back-up copies of data by periodically
storing it on an external storage medium. Use your computer
product only under recommended conditions. Read additional
restrictions under “Environmental Conditions” in your product
“Detailed Specs.” Contact Toshiba Technical Service and
Support for more information.
Graphics
(Graphics Processing
Unit)
ATI Radeon® Xpress 200 (for Celeron® based systems only) or
Intel® Graphics Media Accelerator 950*
3
*Graphics processor unit ("GPU") performance may vary
depending on product model, design configuration,
applications, power management settings and features utilized.
GPU performance is only optimized when operating in AC
power mode and may decrease considerably when operating in
battery power mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
61
Power
Main battery
Removable, rechargeable Lithium-Ion (Li-Ion) high-capacity
4
battery (14.4V x 4000 mAh, 6-cell)*
4
Battery recharge time is several hours*
*Battery life may vary considerably from specifications
depending on product model, configuration, applications,
power management settings and features utilized, as well as
the natural performance variations produced by the design
of individual components. Published battery life numbers
are achieved on select models and configurations tested by
Toshiba at the time of publication. See “Detailed Specs” for
specific battery measurement test. Recharge time varies
depending on usage. Battery may not charge while
computer is consuming full power. After a period of time,
the battery will lose its ability to perform at maximum
capacity and will need to be replaced. This is normal for all
batteries. To purchase a new battery pack, see the
accessories information that shipped with your computer or
RTC battery
Lithium-Ion (Li-Ion) or NiMH battery provides power for
the internal real-time clock and calendar
The RTC battery does not charge while the computer is turned off
even when the AC adaptor is charging the computer.
Storage capacity
Hard Disk Drive (HDD) 2.5-inch removable drive and controller provides non-
Capacity
volatile storage for 40 GB, 60 GB, 80 GB, 100 GB or
120 GB*
5
*1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using
powers of 10. The computer operating system, however,
reports storage capacity using powers of 2 for the definition
of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows
less storage capacity. Available storage capacity will also
be less if the product includes one or more pre-installed
operating systems, such as Microsoft Operating System
and/or pre-installed software applications, or media
content. Actual formatted capacity may vary.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
62
Ports
S-video out port
Lets you play DVD video on a projector or TV that accepts S-
video inputs
DC-IN
Lets you connect the computer to AC power, using the AC
adaptor and power cord/cable
Headphone jack
Microphone jack
RGB (monitor) port
Modem port
Use the 3.5-mm headphone jack to connect stereo
headphones or other audio output devices.
Use the 3.5-mm microphone stereo jack to connect an
external monaural microphone or other audio input device
Use the 15-pin, analog VGA port to connect an external
SVGA monitor (color or monochrome)
Use the modem port to connect the internal modem directly
to a telephone line (purchased separately) via an RJ11
connection
USB 2.0 ports
LAN port
Supports USB 2.0 peripherals (3 ports)
Use the LAN port to connect to a LAN via an RJ45 connection
i.LINK® port
The i.LINK® port (IEEE 1394) provides fast data transfer rates
(up to 400 Mbps) (for Celeron® based systems only)
PC Card slot
The PC Card slot lets you install one Type II or Type I PC Card
Minimum slot thickness: 5 mm
Standard hardware
Memory (Main System) The system may come with 256 MB, 512 MB, or 1024 MB of
6
RAM, expandable to 2048 MB of RAM*
*Part of the main system memory may be used by the graphics
system for graphics performance and therefore reduce the
amount of main system memory available for other computing
activities. The amount of main system memory allocated to
support graphics may vary depending on the graphics system,
applications utilized, system memory size and other factors. For
PCs configured with 4 GB of system memory, the full system
memory space for computing activities will be considerably less
and will vary by model and system configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
63
Display
15.4-inch WXGA (measured diagonally) active matrix Thin
Film Transistor (TFT) color LCD displays up to 16 million
7
colors at 1280 x 800*
Available configurations are: normal and TruBrite
(High Brightness).
*Small bright dots may appear on your screen display when you
turn on your PC. Your display contains an extremely large
number of thin-film transistors (TFT) and is manufactured using
high-precision technology. Any small bright dots that may
appear on your display are an intrinsic characteristic of the TFT
manufacturing technology. Over a period of time, and depending
on the usage of the computer, the brightness of the screen will
deteriorate. This is also an intrinsic characteristic of the screen
technology. When the computer is operated on battery power, the
screen will dim and you may not be able to increase the
brightness of the screen while on battery power.
8
Communication
Integrated V.92 56K modem*
*Due to FCC limitations, speeds of 53 kbps are the maximum
permissible rates during downloads. Actual data transmission
speeds will vary depending on line conditions.
For more detailed information regarding your system’s modem,
visit the Toshiba web site at toshiba.com.
Networking
Realtek 10Base-T/100Base-TX Ethernet LAN adapter with
RJ45 port
Pointing device
Sound controller
TouchPad™ pointing device provides the functionality of a
mouse or other pointing device
Realtek High Definition Audio
Optical drive options
CD-RW/DVD-ROM
drive*
READ: CD-ROM (24x), DVD-ROM (8x)
9
WRITE: CD-R (24x), CD-RW (4x)
Compatibility: CD-ROM (read only), CD-R (read/write),
CD-RW (read/write), DVD-ROM (read only),
DVD-R (read only), DVD-RW (read only),
DVD-RAM (read only)
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications
64
DVD SuperMulti
drive*
READ: CD-ROM, CD-R, CD-RW, DVD-ROM, DVD-R,
DVD-RW, DVD+R, DVD+RW, DVD-RAM
9
Maximum speed and compatibility: CD-ROM (24x),
CD-R (24x), CD-RW (10x), DVD-ROM (8x),
DVD-R (single layer)(8x), DVD-R (double layer)(2x),
DVD-RW (4x), DVD+R (single layer)(8x),
DVD+R (double layer)(2.4x), DVD+RW (4x),
DVD-RAM (5x)
*Due to manufacturing and quality variations in third party
optical media (e.g., CD or DVD) or optical media players/
recorders, in certain cases, your Toshiba optical drive may not
record on certain optical media that bear the applicable logo, or
playback optical media recorded by other PCs or optical media
recorders. Additionally, certain optical media recorded on your
optical drive may not playback or operate properly on other PCs
or optical media players. These problems are not due to any
defect in your Toshiba PC or optical drive. Please refer to your
PC's product specification for listing of specific format
compatibilities.
Copy protection technology may also prevent or limit recording
or viewing of certain optical media.
Wireless Communication
Wi-Fi®
The computer may come with an optional integrated Wi-Fi®
wireless LAN mini PCI communication module providing
10
wireless LAN functions.*
*Wireless connectivity and some features may require you to
purchase additional software, external hardware or services.
Availability of public wireless LAN access points may be
limited. The transmission speed over the wireless LAN and the
distance over which wireless LAN can reach may vary
depending on surrounding electromagnetic environment,
obstacles, access point design and configuration, and client
design and software/hardware configurations. The actual
transmission speed will be lower than the theoretical maximum
speed. To use the Atheros SuperAG™ or SuperG™ wireless
function, if available, your client and access point must support
the corresponding feature. Performance of these functions may
vary depending on the format of data transmitted.
Toshiba recommends that Wi-Fi options be factory-installed at the
time of order.
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal Footnotes
65
Legal Footnotes
1. Product Series
The product specifications and configuration information are designed
for a product Series. Your particular model may not have all the
features and specifications listed or illustrated. For more detailed
information about the features and specifications on your particular
model, visit Toshiba's Web site at pcsupport.toshiba.com.
While Toshiba has made every effort at the time of publication to
ensure the accuracy of the information provided herein, product
specifications, configurations, prices, system/component/options
availability are all subject to change without notice. For the most up-
to-date product information about your computer, or to stay current
with the various computer software or hardware options, visit
Toshiba's Web site at pcsupport.toshiba.com.
2. Processor (Central Processing Unit)
CPU performance in your computer product may vary from
specifications under the following conditions:
❖
❖
❖
use of certain external peripheral products
use of battery power instead of AC power
use of certain multimedia, computer generated graphics or video
applications
❖
❖
use of standard telephone lines or low speed network connections
use of complex modeling software, such as high end computer
aided design applications
❖
❖
use of several applications or functionalities simultaneously
use of computer in areas with low air pressure (high altitude
>1,000 meters or >3,280 feet above sea level)
❖
use of computer at temperatures outside the range of 5° C to
30° C (41° F to 86° F) or >25° C (77° F) at high altitude (all
temperature references are approximate and may vary depending
on the specific computer model – please visit the Toshiba website
CPU performance may also vary from specifications due to design
configuration.
Under some conditions, your computer product may automatically
shut-down. This is a normal protective feature designed to reduce the
risk of lost data or damage to the product when used outside
recommended conditions. To avoid risk of lost data, always make
back-up copies of data by periodically storing it on an external storage
medium. Use your computer product only under recommended
conditions. Read additional restrictions under “Environmental
Conditions” in your product “Detailed Specs.” Contact Toshiba
Technical Service and Support for more information.
3. Graphics (Graphics Processing Unit)
GPU performance may vary depending on product model, design
configuration, applications, power management settings and features
utilized. GPU performance is only optimized when operating in AC
power mode and may decrease considerably when operating in battery
power mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal Footnotes
66
4. Battery Life
Battery life may vary considerably from specifications depending on
product model, configuration, applications, power management
settings and features utilized, as well as the natural performance
variations produced by the design of individual components.
Published battery life numbers are achieved on select models and
configurations tested by Toshiba at the time of publication. See
“Detailed Specs” for specific battery measurement test. Recharge time
varies depending on usage. Battery may not charge while computer is
consuming full power. After a period of time, the battery will lose its
ability to perform at maximum capacity and will need to be replaced.
This is normal for all batteries. To purchase a new battery pack, see
the accessories information that shipped with your computer or visit
5. Hard Disk Drive (HDD) Capacity
1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of
10. The computer operating system, however, reports storage capacity
using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824
bytes, and therefore shows less storage capacity. Available storage
capacity will also be less if the product includes one or more pre-
installed operating systems, such as Microsoft Operating System and/
or pre-installed software applications, or media content. Actual
formatted capacity may vary.
6. Memory (Main System)
Part of the main system memory may be used by the graphics system
for graphics performance and therefore reduce the amount of main
system memory available for other computing activities. The amount
of main system memory allocated to support graphics may vary
depending on the graphics system, applications utilized, system
memory size and other factors. For PCs configured with 4 GB of
system memory, the full system memory space for computing
activities will be considerably less and will vary by model and system
configuration.
7. Display
Small bright dots may appear on your screen display when you turn on
your PC. Your display contains an extremely large number of thin-
film transistors (TFT) and is manufactured using high-precision
technology. Any small bright dots that may appear on your display are
an intrinsic characteristic of the TFT manufacturing technology. Over
a period of time, and depending on the usage of the computer, the
brightness of the screen will deteriorate. This is also an intrinsic
characteristic of the screen technology. When the computer is
operated on battery power, the screen will dim and you may not be
able to increase the brightness of the screen while on battery power.
8. Modem Speed
Due to FCC limitations, speeds of 53 kbps are the maximum
permissible rates during downloads. Actual data transmission speeds
will vary depending on line conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal Footnotes
67
9. Optical Media
Due to manufacturing and quality variations in third party optical
media (e.g., CD or DVD) or optical media players/recorders, in certain
cases, your Toshiba optical drive may not record on certain optical
media that bear the applicable logo, or playback optical media
recorded by other PCs or optical media recorders. Additionally,
certain optical media recorded on your optical drive may not playback
or operate properly on other PCs or optical media players. These
problems are not due to any defect in your Toshiba PC or optical drive.
Please refer to your PC’s product specification for listing of specific
format compatibilities.
Copy protection technology may also prevent or limit recording or
viewing of certain optical media.
10. Wireless
Wireless connectivity and some features may require you to purchase
additional software, external hardware or services. Availability of
public wireless LAN access points may be limited. The transmission
speed over the wireless LAN and the distance over which wireless
LAN can reach may vary depending on surrounding electromagnetic
environment, obstacles, access point design and configuration, and
client design and software/hardware configurations. The actual
transmission speed will be lower than the theoretical maximum speed.
To use the Atheros SuperAG™ or SuperG™ wireless function, if
available, your client and access point must support the corresponding
feature. Performance of these functions may vary depending on the
format of data transmitted.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Index
AC adaptor 28
AC power light 28
alarms
A
DC-IN 29
low battery 47
E
error messages
B
backing up
files 38
battery
alarms 47
changing 47
installing 47, 49
real-time clock (RTC) 46
removing 47
built-in features 59
buttons
F
files
backing up 38
I
eject, optical drive 40
media control 41
TouchPad control 39
inserting
PC Cards 37
C
CD/DVD
inserting 43
CD/DVD button functionality 41
changing
main battery 47
computer
internal drives 64
K
unexpected characters 54
moving 45
not working 54
setting up 31
computing tips 38
connecting
L
lights
AC adaptor 28
power cord/cable 29
printer 30
AC power 28
M
control buttons
TouchPad 39
main battery
changing 47
installing 47, 49
Download from Www.Somanuals.com. All Manuals Search And Download.
69
removing 47
media control buttons 41
memory module
installing 30
inserted 56
display is blank 54
inserting into socket 33
removing 35
external monitor 55
illegal operation 53
memory module slot 31
removing cover 32
monitor problems
keyboard not responding 54
keyboard produces unexpected
characters 54
monitor not working 55
moving the computer 45
PC Card checklist 56
PC Card slot appears dead 56
program not responding 52
processor, specifications 59
O
optical drive
63
eject button 40
inserting a disc 43
removing disc 44
using 40
real-time clock (RTC) battery 46
removing
CD/DVD
with computer off 44
with computer on 44
memory module 35
P
PC Card
inserting 37
removing 38
PC Card problems 56
computer stops working 56
slot appears dead 56
port
specifications 62
power
S
precautions 26
saving
screen problems
secondary button
setting
cable connectors 58
cord/cable 29
specifications 61
power devices 64
power problems
computer will not start 53
precautions 26
primary button
TouchPad 39
battery alarms 47
setting up
AC adaptor 28
computer 31
specifications
optical drive 63
ports 62
printer
connecting 30
problem solving
computer hangs when PC Card
power 61
processor 59
Download from Www.Somanuals.com. All Manuals Search And Download.
70
standard hardware 62
storage capacity 61
wireless communication 64
standard hardware, specifications 62
storage capacity
specifications 61
T
tips on computing 38
Toshiba Accessories
information 30
TouchPad
using 39
W
Web sites 57
wireless communication
64
wireless interoperability 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PMA500332010
05/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|