Toshiba Flat Panel Television 26LV47 User Manual

DRAFT1

Integrated High Definition

LCD TV/DVD Combination

HIGH-DEFINITION TELEVISION

26LV47

Owner’s Record

The model number and serial number are on the back of

your TV. Record these numbers in the spaces below.

Refer to these numbers whenever you communicate

with your Toshiba dealer about this TV.

For an overview of steps for setting up your new TV, see page 12.

Note: To display a High Definition picture, the TV must be receiving a

High Definition signal (such as an over-the-air High Definition TV

broadcast, a High Definition digital cable program, or a High Definition

digital satellite program). For details, please contact your TV antenna

installer, cable provider, or satellite provider.

Model number:

Serial number:

26LV47

YC/M

VX1A00068600

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Safety Instructions

15) CAUTION:

• To reduce the risk of electric shock, do not use the

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

polarized plug with an extension cord, receptacle, or

other outlet unless the blades can be inserted

completely to prevent blade exposure.

• To prevent electric shock, match wide blade of plug to

wide slot; fully insert.

4) Follow all instructions.

5) Do not use this apparatus near water.

16) WARNING:

6) Clean only with dry cloth.

To prevent the spread of fire, keep candles or other open

flames away from this product at all times.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all

warnings when installing your TV:

9) Do not defeat the safety purpose of

Wide blade

the polarized or grounding type

plug. A polarized plug has two blades

with one wider than the other.

A grounding type plug has two blades

and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

17) Never modify this equipment. Changes or modifications

may void: a) the warranty, and b) the user’s authority to

operate this equipment under the rules of the Federal

Communications Commission.

18)

DANGER: RISK OF

SERIOUS PERSONAL

INJURY, DEATH, OR

10) Protect the power cord from being walked

on or pinched, particularly at plugs,

EQUIPMENT DAMAGE!

Never place the TV on an unstable cart,

stand, or table. The TV may fall, causing

serious personal injury, death, or serious

damage to the TV.

convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

19) To avoid damage to this product, never place or store the

TV in direct sunlight; hot, humid areas; or areas subject to

excessive dust or vibration.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

20) Always place the TV on the floor or a sturdy, level, stable

surface that can support the weight of the unit. To secure

the TV, use a sturdy tie from the hooks on the rear of the

TV pedestal to a wall, pillar, or other immovable structure.

Make sure the tie is tight, secure, and parallel to the floor.

apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

Sturdy tie (as short as possible)

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been

dropped.

min.

Clip

Hooks

Clip

TV side

TV top

21) The apparatus shall not be exposed to dripping or

splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

Additional Safety Precautions

14a) CAUTION: If the TV is dropped and the cabinet or

enclosure surface has been damaged or the TV does not

operate normally, take the following precautions:

22) Never block or cover the slots or openings in the TV

cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar

surface;

• too close to drapes, curtains, or

walls; or

• in a confined space such as a

bookcase, built-in cabinet, or

any other place with poor

ventilation.

The slots and openings are provided to protect the TV from

overheating and to help maintain reliable operation of the

TV. Leave a space of at least 4 (four) inches around the TV.

• ALWAYS turn off the TV and unplug the power cord to

avoid possible electric shock or fire.

• NEVER allow your body to come in contact with any

broken glass or liquid from the damaged television. The

LCD panel inside the TV contains glass and a toxic

liquid. If the liquid comes in contact with your mouth or

eyes, or your skin is cut by broken glass, rinse the

affected area thoroughly with water and consult your

doctor.

• ALWAYS contact a service technician to inspect the TV

any time it has been damaged or dropped.

(5 inches away from the TV slot side).

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

23) Always place the back of the television at least four (4)

inches away from any vertical surface (such as a wall) to

allow proper ventilation.

31)

WARNING:

RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV

cabinet slots.

24) Never allow anything to rest on or roll over the power cord,

and never place the TV where the power cord is subject to

wear or abuse.

32) While it is thundering, do not touch the connecting cables

or apparatus.

25) Never overload wall outlets and extension cords.

33) For added protection of your TV from lightning and power

surges, always unplug the power cord and disconnect the

antenna from the TV if you leave the TV unattended or

unused for long periods of time.

26) Always operate this equipment from a 120 VAC, 60 Hz

power source only.

27) Always make sure the antenna system is properly

grounded to provide adequate protection against voltage

surges and built-up static charges (see Section 810 of the

National Electric Code).

34) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the

unit is being turned on or off. If these sounds become

frequent or continuous, unplug the power cord and contact

a Toshiba Authorized Service Center.

Antenna lead-in wire

Antenna discharge unit

35)

WARNING: RISK OF

SERIOUS PERSONAL

INJURY OR EQUIPMENT

DAMAGE!

(NEC Section 810-20)

Ground clamp

Grounding conductors

(NEC Section 810-21)

Never strike the screen with a sharp

or heavy object.

Electric service equipment

36) • The LCD screen of this product can be damaged by

ultraviolet radiation from the sun. When selecting a

location for the television, avoid locations where the

screen may be exposed to direct sunlight, such as in

front of a window.

Power service grounding

electrode system (NEC Art 250 Part-H)

Ground clamps

28)

DANGER: RISK OF SERIOUS

PERSONAL INJURY OR DEATH!

• Never touch, press, or place anything on the LCD

screen. These actions will damage the LCD screen. If

you need to clean the LCD screen, follow the

instructions in item 30 on this page.

• Use extreme care to make sure you are never in a

position where your body (or any item you are in contact

with, such as a ladder or screwdriver) can accidentally

touch overhead power lines. Never locate the antenna

near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during

lightning activity: a) an antenna system; or b) cables,

wires, or any home theater component connected to an

antenna or phone system.

Service

37)

WARNING:

RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself. Opening and

removing the covers may expose you to dangerous

voltage or other hazards. Failure to follow this WARNING

may result in death or serious injury. Refer all servicing not

specified in this manual to a Toshiba Authorized Service

Center.

Care

For better performance and safer operation of your TOSHIBA

TV, follow these recommendations and precautions:

29) If you use the TV in a room whose temperature is 32 ºF

(0 ºC) or below, the picture brightness may vary until the

LCD warms up. This is not a sign of malfunction.

38) If you have the TV serviced:

• Ask the service technician to use only replacement

parts specified by the manufacturer.

30) Always unplug the TV before

cleaning. Gently wipe the

display panel surface (the TV

screen) using a dry, soft cloth

only (cotton, flannel, etc.). A

hard cloth may damage the

surface of the panel. Avoid

• Upon completion of service, ask the service technician

to perform routine safety checks to determine that the

TV is in safe operating condition.

39) The cold cathode fluorescent lamp in the LCD panel

contains a small amount of mercury.

contact with alcohol, thinner, benzene, acidic or alkaline

solvent cleaners, abrasive cleaners, or chemical cloths,

which may damage the surface. Never spray volatile

compounds such as insecticide on the cabinet. Such

products may damage or discolor the cabinet.

When the TV reaches the end of its useful life, dispose of

the used TV by the approved method for your area, or ask

a qualified service technician to properly dispose of the

TV.

Note: The lamp(s) inside this product contain

mercury. Disposal may be regulated due to

environmental considerations. For disposal or

recycling information, contact your local authorities or the

Electronics Industries Alliance (www.eiae.org).

Download from Www.Somanuals.com. All Manuals Search And Download.

Choosing a location for your LCD TV

Safety and Care Information for

TV/DVD Combination Models

To Display your LCD TV on the included Pedestal

Stand:

DISC SLOT

Observe the following safety precautions:

• Keep your fingers well clear of the disc slot when the disc is

loading or unloading. Neglecting to do so may cause personal

injury.

1) Read and Follow the pedestal assembly instructions included

with the pedestal.

CAUTION: Before beginning pedestal assembly, carefully lay

the front of the LCD Panel face down on a flat, cushioned

surface such as a quilt or blanket. Leave the bottom of the unit

protruding over the edge of the surface and assemble the

pedestal as indicated below.

LASER BEAM

• Never look into the opening of the disc slot or ventilation

opening of the product to see the source of the laser beam.

Staring directly at the beam may cause permanent damage to

your eyesight.

Note: Extreme care should always be used when attaching

the pedestal stand to avoid damage to the LCD panel.

2) Place the TV on a sturdy, level surface that can support the

weight of the TV.

3) Be sure to secure the TV to a wall, pillar, surface, or other

immovable structure. To secure the TV in this manner, use the

included strap located at the rear of pedestal stand. (-item 20,

page 3).

DISC

• Do not use a cracked, deformed, or repaired disc. These discs

are easily broken and may cause serious personal injury and

product malfunction.

Precautions

To Display your LCD TV using a Wall Bracket:

If you decide to wall mount your LCD TV, always use a UL-

listed wall bracket appropriate for the size and weight of the

LCD TV (- page 2) :

VIBRATION

• Vibration or shock may disrupt DVD playback or cause

scratches on the disc. Do not move or tilt or otherwise jolt the

TV when a disc is loaded. The playback sound may skip if the

TV is dropped from a height of 1.58 inch (4 cm) or more or if

the TV is installed at a greater angle than recommended.

1) CAUTION: Two people are required for installation.

2) Unplug and remove any cables and/or other component

connectors from the rear of the TV.

3) Follow the instructions provided with your wall bracket.

Before proceeding, make sure the appropriate bracket(s) are

attached to the wall and the back of the TV as described in the

instructions provided with the wall bracket.

4) After attaching the appropriate bracket(s) to the wall and the

back of the TV, remove the pedestal stand from the TV as

described below.

Notes on moisture condensation

Moisture condensation occurs, for example, when you pour a

cold drink into a glass on a warm day. Drops of water form on

the outside of the glass. In the same way, moisture may

condense on the optical pick-up lens inside the DVD player,

one of the most crucial internal parts of the DVD player.

Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat,

cushioned surface such as a quilt or blanket. Leave the stand

protruding over the edge of the surface.

Optical pick-up

lens

Note: Extreme care should always be used when removing

the pedestal stand to avoid damage to the LCD panel.

2) Remove the jack pack cover on the back of the TV to expose

the pedestal stand screws. The jack pack cover can be removed

without tools.

3) Remove the five screws shown in the diagram below. This will

allow removal of the pedestal stand.

4) Once you have removed all five screws holding the pedestal

stand in place, remove the pedestal stand from the TV by

sliding the pedestal stand away from the TV.

Moisture condensation can occur in the following

conditions:

• When the TV is moved directly from a cold or air conditioned

area to a warm or humid area.

• When the TV is placed in an area in which the heat has just

been turned on, or where cold air from an air conditioner falls

directly on the TV.

Five screws

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not use the DVD player when moisture condensation

may be present.

On storing discs

• Never store discs near heat sources or in an area subject to

direct sunlight.

• Never store discs in places subject to moisture and dust (such

as near a humidifier or in a bathroom).

• Store discs vertically in a case. Stacking or placing objects on

discs outside of their case may cause warping.

If you use the DVD player in such a situation, the DVD player

and/or discs may become damaged. Connect the power cord of

the TV to the wall outlet, turn on the TV, remove the disc, and

leave the TV on for two or three hours. After two or three hours,

the TV will have warmed up and evaporated any moisture.

Leaving the TV connected to the wall outlet will help prevent

moisture condensation in the TV or DVD player.

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles

are sub-divided into chapters. Video CDs and Audio CDs are

divided into tracks.

Wall outlet

DVD video disc

Title 1

Title 2

Chapter 1 Chapter 2

Chapter 1 Chapter 2 Chapter 3

Notes on discs

On handling discs

• Do not touch the playback side of the disc.

For example, handle the disc as shown below.

Video CD/Audio CD

Track 2 Track 3 Track 4

Track 1

Track 5

Each title, chapter or track is assigned a number (the “title

number,” “chapter number,” and “track number,” respectively).

Playback side

Some discs do not have these numbers.

• Do not attach paper or tape to discs.

Notes on copyright

DO NOT

The unauthorized recording, use, distribution, or

revision of television programs, videotapes, DVDs, and

other materials is prohibited under the Copyright Laws

of the United States and other countries, and may

subject you to civil and criminal liability.

On cleaning discs

• Fingerprints and dust on discs cause picture and sound

deterioration. Wipe discs from the center outward with a soft

cloth. Always keep discs clean.

This product incorporates copyright protection technology that

is protected by U.S. patents and other intellectual property

rights. Use of this copyright protection technology must be

authorized by Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized by

Macrovision. Reverse engineering or disassembly is prohibited.

DO NOT

• Never use any type of solvent (such as thinner, benzine,

commercially available cleaners or antistatic spray for vinyl

LPs). Using such solvents may damage the discs.

Notes on region numbers

The region number of this DVD player of the TV is 1. If region

numbers, which stand for their playable area, are printed on

ALL

your DVD video disc and you do not find

, disc

playback will not be allowed by the DVD player. (In this case,

the TV will display a message on-screen.)

Some DVDs that have no region code label may still be subject

to area restrictions and are therefore not playable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playable discs

This DVD player can play the following discs with the

corresponding logo.

CAUTION:

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER

SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE

READ THIS OWNER’S MANUAL CAREFULLY AND

RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT

REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED

SERVICE LOCATION.

USE OF CONTROLS OR ADJUSTMENTS, OR THE

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN, MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO THE LASER

BEAM, NEVER TRY TO OPEN THE ENCLOSURE.

VISIBLE LASER RADIATION MAY BE PRESENT WHEN

THE ENCLOSURE IS OPENED. NEVER STARE INTO THE

BEAM.

Maximum

Disc

Size

Disc Mark Contents

playback time

Approx. 4 hours

(single-sided disc)

12 cm

8 cm

Audio

Video

(moving

pictures)

Approx. 8 hours

(double-sided disc)

DVD

video

discs

Approx. 30 minutes

(single-sided disc)

Approx. 60 minutes

(double-sided disc)

Audio

Video

CDs

12 cm

Approx. 74 minutes

(moving

pictures)

DIGITAL VIDEO

Location of required label

12 cm

8 cm

Approx. 74 minutes

Approx. 22 minutes

HONG KONG TOHEI E.M.C. CO.,LTD.

Audio

CDs

Unit No.D,9th Floor, Spectrum Tower,

53 Hung To Road,Kwun Tong,Kowloon,

Hong Kong

CLASS 1 LASER PRODUCT

Audio

CAUTION:VISIBLE AND INVISIBLE

LASER RADIATION WHEN OPEN

AVOID EXPOSURE TO BEAM

COMPLIES WITH 21 CFR

1040.10 AND 1040.11

EXCEPT FOR DEVIATIONS

PURSUANT TO LASER

NOTICE NO.50, DATED

(JULY 26, 2001 ).

The following discs may also be compatible:

DVD-R/RW discs in DVD video format.

CD-R/CD-RW discs in CD-DA, Video CD, MP3,

or JPEG format.

Kodak Picture CD and FUJICOLOR CD format.

• You cannot play discs other than those listed above. You

cannot play discs in formats such as DVD-RAM, DVD-ROM,

Photo CD, Super Audio CD (SACD™), etc., or non

standardized discs even if they may be labeled as above. The

damage depending on the use of those discs is NOT covered

under your Toshiba warranty.

Slot - in DVD / CD player

module DVC - 303S - TO

No.XXXXX

• Some CD-R/RWs cannot be played back depending on the

recording conditions.

• This TV uses the NTSC color system, and cannot play DVD

video discs recorded in any other color system (for example,

PAL or SECAM).

• Do not use the CD single adapter since it may not play

properly.

Because of problems and errors that can occur during the

creation of DVD and CD software and/or the manufacture of

DVD and CD discs, Toshiba cannot assure that the DVD

player contained in your TV/DVD Combination will

successfully play every disc bearing the DVD and CD logos.

If you happen to experience any difficulty playing a DVD

and/or CD disc on the DVD player contained in your TV/DVD

Combination, please contact Toshiba Customer Service.

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC Declaration of Conformity Important notes about your LCD

Compliance Statement

(Part 15):

TV/DVD combination

The following symptoms are technical limitations of LCD

Display technology and are not an indication of malfunction;

therefore, Toshiba is not responsible for perceived issues

resulting from these symptoms.

The Toshiba 26LV47 Television complies with Part 15 of the

FCC rules.

1) An afterimage (ghost) may appear on the screen if a fixed, non-

moving image is displayed for a long period of time. The

afterimage is not permanent and will disappear in a short period

of time.

2) The LCD panel contained in this TV is manufactured using an

extremely high level of precision technology; however, there

may be an occasional pixel (dot of light) that does not operate

properly (does not light, remains constantly lit, etc.). This is a

structural property of LCD technology, is not a sign of

malfunction, and is not covered under your warranty. Such

pixels are not visible when the picture is viewed from a normal

viewing distance.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that

may cause undesired operation.

The party responsible for compliance to these rules is:

Toshiba America Consumer Products, L.L.C.

82 Totowa Rd. Wayne, NJ 07470.

Ph: 1-800-631-3811

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15

of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

removing and applying power to the equipment, the user is

encouraged to try to correct the interference by one or more of

the following measures:

Note: Interactive video games that involve shooting a “gun”

type of joystick at an on-screen target may not work with this

TV.

About this owner’s manual (DVD

player section)

This owner’s manual explains the basic instructions for using the

internal DVD player. Some DVDs are produced in a manner that

allows specific or limited operation during playback. As such, the

DVD player may not respond to all operating commands. This is

not a defect in the DVD player.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Refer to the instructions provided with your DVDs.

• Consult the dealer or an experienced radio/TV technician for

help.

If the symbol “ ” appears on-screen during DVD operation, it

means that the operation or feature is not permitted or available for

the DVD player or disc.

Caution: Changes or modifications to this equipment not

expressly approved by Toshiba could void the user’s authority

to operate this equipment.

For example, sometimes the DVD player is unable to stop

playback of the DVD’s copyright message when the D button is

pressed.

Trademark Information

• WOW, SRS and l symbol are trademarks of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc.

• Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are registered trademarks of Dolby

Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

•

is a trademark of DVD Format/Logo Licensing Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Switching between two channels using SurfLock^™. . . . 41

Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Scrolling the TheaterWide^®picture

Important Safety Instructions .......................................... 3

Installation, Care, and Service ........................................ 3

(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 43

Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 44

Selecting the cinema mode (480i and 1080i signals) . . . . . . 44

Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . . . 45

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 45

Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 46

Base closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Digital CC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

CC Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Using the digital audio selector . . . . . . . . . . . . . . . . . . . 47

Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 48

Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 48

Using the StableSound^®feature. . . . . . . . . . . . . . . . . . . 49

Selecting the optical audio output format . . . . . . . . . . . 49

Using the Dolby^®Digital Dynamic Range

Safety and Care Information for

TV/DVD Combination Models .......................................... 5

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Overview of steps for installing, setting up, and using

your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

TV front and side panel controls and connections . . . . . . . . 13

TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 2: Connecting your TV . . . . . . . . . . . . . . . . . . . . . . .15

Overview of cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

About the connection illustrations . . . . . . . . . . . . . . . . . . . . 15

Connecting a VCR and antenna or Cable TV

(no Cable box) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting a VCR with S-video and a cable box . . . . . . . . 17

Connecting a DVD player with ColorStream^®

(component video), a VCR, and a satellite receiver. . . . 18

Connecting a camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting an HDMI^™or DVI device to the HDMI

input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting a digital audio system . . . . . . . . . . . . . . . . . . . . 21

Connecting an audio system . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting a personal computer (PC) . . . . . . . . . . . . . . . . . 22

Control feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 50

If you cannot remember your PIN code. . . . . . . . . . . . . 50

Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 50

Blocking TV programs and movies by rating

(V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Downloading an additional rating system for blocking

TV programs and movies . . . . . . . . . . . . . . . . . . . . 51

Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Unlocking programs temporarily. . . . . . . . . . . . . . . . . . 53

Using the input lock feature. . . . . . . . . . . . . . . . . . . . . . 53

Using the control panel lock feature . . . . . . . . . . . . . . . 54

Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 54

Setting the PC Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Displaying TV status information. . . . . . . . . . . . . . . . . . . . . 56

Understanding the auto power off feature . . . . . . . . . . . . . . 56

Understanding the last mode memory feature . . . . . . . . . . . 56

Chapter 3: Using the remote control . . . . . . . . . . . . . . . . . . .23

Preparing the remote control for use. . . . . . . . . . . . . . . . . . . 23

Installing the remote control batteries . . . . . . . . . . . . . . . . . 23

Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . 23

Learning about the remote control . . . . . . . . . . . . . . . . . . . . 24

Using the remote control to control your other devices . . . . 25

Remote Control functional key chart . . . . . . . . . . . . . . . . . . 26

Programming the remote control to control your other

devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Chapter 4: Menu layout and navigation . . . . . . . . . . . . . . . . .30

Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 31

Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 31

Chapter 7: Using the TV’s advanced features . . . . . . . . . . . . .57

Using the advanced picture settings features . . . . . . . . . . . . 57

Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 57

Using the static gamma feature . . . . . . . . . . . . . . . . . . . 57

Selecting the color temperature . . . . . . . . . . . . . . . . . . . 58

Using CableClear^®digital noise reduction . . . . . . . . . . 58

Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 59

Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 59

Using the advanced audio settings features . . . . . . . . . . . . . 60

Using the SRS WOW^™surround sound feature . . . . . . 60

Chapter 5: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .32

Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 32

Configuring the antenna input source for the ANT

terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Programming channels into the TV’s channel memory . . . . 33

Programming channels automatically . . . . . . . . . . . . . . 33

Manually adding and deleting channels in the channel

memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Labeling channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setting the HDMI^™audio mode. . . . . . . . . . . . . . . . . . . . . . 35

Viewing the digital signal meter. . . . . . . . . . . . . . . . . . . . . . 36

Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Chapter 8: DVD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . .61

Playing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Using the DVD aspect ratio feature . . . . . . . . . . . . . . . . . . . 63

Playing in fast reverse or fast forward . . . . . . . . . . . . . . . . . 63

To pause playback (still playback) . . . . . . . . . . . . . . . . . . . 63

Playing frame by frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Playing in slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Locating a chapter or track . . . . . . . . . . . . . . . . . . . . . . . . . 64

Changing angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Title selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Changing soundtrack language . . . . . . . . . . . . . . . . . . . . . . 65

Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Disc status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

(continued)

Chapter 6: Using the TV’s features . . . . . . . . . . . . . . . . . . . .38

Selecting the video input source to view . . . . . . . . . . . . . . . 38

Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 38

Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Tuning channels using the Channel Browser^™. . . . . . . 39

Tuning to the next programmed channel . . . . . . . . . . . . 41

Tuning to a specific channel (programmed or

unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Switching between two channels using Channel

Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/JPEG CD operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

MP3/JPEG CD information . . . . . . . . . . . . . . . . . . . . . 66

MP3 CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

JPEG CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Chapter 9: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .69

General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

DVD Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Chapter 10: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Limited United States Warranty

for LCD TV/DVD Combinations 26” and Larger . . . . . 73

Limited Canadian Warranty

for Toshiba Brand Flat Panel Televisions . . . . . . . . . . . 74

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1: Introduction

Welcome to Toshiba

Features of your new TV

Thank you for purchasing this Toshiba LCD TV/DVD

combination, one of the most innovative LCD TVs on the

market. This digital television is capable of receiving analog

basic, digital basic and digital premium cable television

programming by direct connection to a cable system providing

such programming. A security card provided by your cable

operator is required to view encrypted digital programming.

Certain advanced and interactive digital cable services such as

video-on-demand, a cable operator's enhanced program guide

and data-enhanced television services may require the use of a

set-top box. For more information call your local cable

operator.

The following are just a few of the many exciting features of

your new Toshiba widescreen, integrated HD, LCD TV:

• Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top

box (in most cases).

• Three HDMI^™digital, high-definition multimedia

interfaces 1080p input support (- page 20).

• Two sets of ColorStream^®HD high-resolution component

video inputs (- page 18).

• SRS WOW^™audio technologies (- page 60).

• Digital Audio Out optical audio connection with Dolby^®

Digital optical output format (- page 49).

• CableClear^®digital picture noise reduction

(- page 58).

• PC IN (Analog RGB) computer terminal (- page 22).

• DVD video (and Video CD, Audio CD) player

(- page 61).

• Channel Labeling allows you to put the Call Letters (e.g.

ABC, HBO, etc.) on the screen along with the station

numbers, so you always know what you’re watching

(- page 34).

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1: Introduction

10 See “Menu layout and navigation” for a quick overview of

Overview of steps for installing,

setting up, and using your new TV

navigating the TV’s menu system (- page 30).

11 Program channels into the TV’s channel memory

(- page 33).

12 For details on using the TV’s features, see Chapters 6

Follow these steps to set up your TV and begin using its many

exciting features.

and 7.

13 For details on using the DVD’s features, see Chapter 8.

14 For help, refer to the Troubleshooting Guide, Chapter 9.

Carefully read the important safety, installation, care, and

service information. Keep this manual for future

reference.

15 For technical specifications and warranty information, see

Chapter 10.

Observe the following when choosing a location for the

TV:

• Read “Important notes about your LCD TV/DVD

16 Enjoy your new TV/DVD!

combination” (- page 8).

• Place the TV on the floor or a sturdy, level, stable

surface that can support the weight of the unit. Secure

the TV to a wall, pillar, or other immovable structure

(- page 3).

• Place the TV in a location where light does not reflect

on the screen.

• Place the TV far enough from walls and other objects to

allow proper ventilation. Inadequate ventilation may

cause overheating, which will damage the TV. THIS

TYPE OF DAMAGE IS NOT COVERED UNDER

THE TOSHIBA WARRANTY.

Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

BEFORE connecting cables or devices to the TV, learn

the functions of the TV’s connections and controls

(- pages 13–14).

Connect your other electronic device(s) to the TV

(- pages 15–22).

Install the batteries in the remote control (- page 23).

See “Learning about the remote control” (- page 24) for

an overview of the buttons on the remote control.

Program the remote control to operate your other

device(s) (- pages 25–29).

AFTER connecting all cables and devices, plug in the

power cords for your TV and other devices. The yellow

LED will blink until the TV goes into standby mode.

When the TV is in standby mode, press POWER on the

TV control panel or remote control to turn on the TV.

If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn the TV

off or on, press and hold the POWER button for 5

seconds to reset the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1: Introduction

TV front and side panel controls and connections

Left side panel

Right side panel

TV front

TV top

Control panel

DISC

POWER

Green and Yellow LEDs

Green = Power indicator

Yellow = Disc indicator

See “LED indications” on page 71 for additional

information.

CHANNEL Bb — When no menu is on-screen, these

buttons change the channel (programmed channels only;

- page 33).

VOLUME C c — These buttons adjust the volume level.

10 INPUT — Repeatedly press to change the source you are

viewing (ANT, Built-In DVD, VIDEO 1, VIDEO 2,

ColorStream HD1, ColorStream HD2, HDMI 1,

HDMI 2, HDMI 3, PC).

Remote sensor — Point the remote control toward this

remote sensor (- “Remote control effective range” on

page 23).

11 PLAY — Press to play a DVD video disc, or other

VIDEO-2 IN — The side panel A/V connections are

referred to as “VIDEO 2” and include standard A/V

connections.

playable disc.

12 STOP — Press to stop a DVD video disc, or other

playable disc.

POWER — Press to turn the TV on and off.

If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn off the

TV, press and hold the POWER button on the TV control

panel for 5 or more seconds to reset the TV.

13 SKIP — Press to skip DVD chapter, or CD track.

14 OPEN/CLOSE — Press to eject a disc.

15 DVD disc slot — Insert a playable disc to play.

ARROWS BbC c — When a menu is on-screen, these

buttons function as up/down/left/right menu navigation

buttons.

MENU (ENTER) — Press to access the menu system

(- pages 30–31). When a menu is on-screen, the MENU

button on the TV’s control panel functions as the ENTER

button.

EXIT — Press to instantly close an on-screen menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1: Introduction

TV back panel connections

For an explanation of cable types and connections, see pages 15–22.

TV back

Power cord

Cable Clamper

6 7

ColorStream^®HD-1 and ColorStream^®HD-2 —

Two sets of ColorStream^®high-definition component

video inputs (with standard stereo audio inputs) for

connecting devices with component video output, such as

a Toshiba DVD player with ColorStream^®.

Digital Audio OUT — Optical audio output in Dolby

Digital or PCM (pulse-code modulation) format for

connecting an external Dolby Digital decoder, amplifier,

A/V receiver, or home theater system with optical audio

input.

HDMI^™IN — High-Definition Multimedia Interface

input receives digital audio and uncompressed digital

video from an HDMI device or uncompressed digital

video from a DVI device. Also see item 4. HDMI

connection is necessary to receive 1080p signals.

Note: Component video cables carry only video

information; separate audio cables are required for a

complete connection.

VIDEO-1 IN — Standard (composite) video and standard

audio inputs plus optional S-video inputs for connecting

devices with composite video or S-video output.

Service port — For service use only. Used for updating

the television’s firmware.

Note: Standard (composite) video and S-video cables

carry only video information; separate audio cables are

required for a complete connection.

HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are registered trademarks of Dolby

Laboratories.

Fixed Audio OUT — Analog audio outputs for

connecting an audio amplifier.

PC/HDMI-1 (AUDIO) IN — PC audio input terminals

are shared with HDMI-1 analog audio input terminals, and

their use can be configured in the Audio Setup menu

(- page 55).

PC IN — For use when connecting a personal computer.

ANT — Antenna input that supports analog (NTSC) and

digital (ATSC) off-air antenna signals and analog and

digital Cable TV (QAM) signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

HDMI^™cable cable (with HDMI Logo “

”)

Overview of cable types

Cables can be purchased from most stores that sell audio/video

devices. Before purchasing any cables, be sure of connector

types required by your devices and the length of each cable.

HDMI (High-Definition Multimedia Interface) cable is for use

with devices with an HDMI output. An HDMI cable delivers

digital audio and video in its native format. This cable carries

both video and audio information; therefore, separate audio

cables are not required for a complete HDMI device

connection (- page 20 and page 22).

Coaxial (F-type) cable

Note: HDMI cable provides better picture performance than a

standard (composite) video or S-video cable.

Coaxial (F-type) cable is used for connecting your antenna,

cable TV service, and/or cable converter box to the ANT input

on your TV.

Optical audio cable

Standard A/V cables (red/white/yellow)

Optical audio cable is for connecting receivers with Dolby

Digital or PCM (pulse-code modulation) optical audio input to

the TV’s DIGITAL AUDIO OUT terminal (- page 21).

Standard A/V cables (composite video) usually come in sets of

three, and are for use with video devices with analog audio and

composite video output. These cables (and the related inputs

on your TV) are typically color-coded according to use: yellow

for video, red for stereo right audio, and white for stereo left

(or mono) audio.

Analog RGB (15-pin) computer cable

Analog RGB (15-pin) computer cable is for connecting a PC to

the TV’s PC IN terminal (- page 22).

S-video cable

S-video cable is for use with video devices with S-video

output. Separate audio cables are required for a complete

connection.

About the connection illustrations

You can connect different types and brands of devices to your

TV in several different configurations. The connection

illustrations in this manual are representative of typical device

connections only. The input/output terminals on your devices

may differ from those illustrated herein. For details on

connecting and using your specific devices, refer to each

device’s owner’s manual.

Note: An S-video cable provides better picture performance

than a composite video cable. If you connect an S-video cable,

be sure to disconnect the standard (composite) video cable or

the picture performance will be unacceptable.

Component video cables (red/green/blue)

Component video cables come in sets of three and are for use

with video devices with component video output.

(ColorStream^®is Toshiba’s brand of component video.) These

cables are typically color-coded red, green, and blue. Separate

audio cables are required for a complete connection.

Note: Component video cables provide better picture

performance than a standard (composite) video or S-video

cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

Connecting a VCR and antenna or Cable TV (no Cable box)

TV upper back panel

From Cable TV or antenna

Stereo VCR

VIDEO

AUDIO

IN from ANT

OUT to TV

CH 3

CH 4

OUT

TV lower back panel

You will need:

To view the antenna or Cable signal:

Select the ANT video input source on the TV.*

• coaxial cables

• standard A/V cables

To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on

the TV.*

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) instead of

the standard video cable. Do not connect both types of

video cable to VIDEO 1 at the same time or the picture

performance will be unacceptable.

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

* To select the video input source, press INPUT on the remote control

(- page 24). To program the TV remote control to operate other

devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

Connecting a VCR with S-video and a cable box

An S-video connection will provide better picture performance than a standard (composite) video cable.

From Cable TV

TV upper back panel

Cable box

CH 3

CH 4

OUT

stereo VCR

VIDEO

AUDIO

IN from ANT

OUT to TV

CH 3

CH 4

OUT

TV lower back panel

You will need:

To view basic and premium Cable channels:

Turn OFF the VCR. Select the ANT video input source on the

TV.* Tune the TV to channel 3 or 4 (whichever channel the

Cable box output is set to). Use the Cable box controls to

change channels.

• coaxial cables

• S-video cable

– Do not connect both types of video cable to VIDEO 1 at

the same time or the picture performance will be

unacceptable.

To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on

the TV.*

• standard audio cables

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

* To select the video input source, press INPUT on the remote control

(- page 24). To program the TV remote control to operate other

devices, see Chapter 3.

Note: When you use a Cable box, you may not be able to use

the remote control to program or access certain features on the

TV.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

Connecting a DVD player with ColorStream^®(component video), a VCR,

and a satellite receiver

Your TV has two sets of ColorStream^®(component video) inputs.

TV upper back panel

From antenna

Stereo VCR

AUDIO

OUT

VIDEO

AUDIO

IN from ANT

OUT to TV

COMPONENT VIDEO

VIDEO

OUT

CH 3

CH 4

S-VIDEO

OUT

DVD player with component video

From satellite dish

AUDIO

OUT

VIDEO

OUT

COMPONENT VIDEO

Satellite

S-VIDEO

OUT

TV lower back panel

Satellite receiver with component video

You will need:

• coaxial cables

To view satellite programs using the component video

connections:

Turn on the satellite receiver. Select the ColorStream HD-2

• standard A/V cables

video input source on the TV.*

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) instead of

the standard video cable. Do not connect both types of

video cable to VIDEO 1 at the same time or the picture

performance will be unacceptable.

To view the VCR or view and record antenna

channels:

Turn ON the VCR. Tune the VCR to the channel you want to

watch. Select the VIDEO 1 video input source on the TV.*

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable

only.

To record a TV program while watching a DVD:

Turn ON the VCR. Tune the VCR to the channel to record.

Select the ColorStream HD-1 video input source on the TV*

to view the DVD.

• standard audio cables

• component video cables

– You can connect the component video cables (plus audio

cables) from the DVD player or satellite receiver to either

set of ColorStream terminals on the TV (HD-1 or HD-2).

The ColorStream HD-1 and HD-2 terminals can be used

with Progressive (480p, 720p) and Interlaced (480i, 1080i)

scan systems. A 1080i signal will provide the best picture

performance (1080p is not supported).

– If your DVD player or satellite receiver does not have

component video, connect a standard A/V cable to

VIDEO 2 on the side panel. If your DVD player has HDMI

video, see page 20.

* To select the video input source, press INPUT on the remote control

(- page 24). To program the TV remote control to operate other

devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of

television programs, videotapes, DVDs, and other materials is

prohibited under the Copyright Laws of the United States and

other countries, and may subject you to civil and criminal

liability.

To view antenna or Cable channels:

Select the ANT video input source on the TV.*

To view the DVD player:

Turn ON the DVD player. Select the ColorStream HD-1

video input source on the TV.*

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

Connecting a camcorder

You will need:

• standard A/V cables

– For better picture performance, if your camcorder has

S-video, connect an S-video cable (plus the audio cables)

to VIDEO 1 on the TV back instead of the VIDEO 2 on the

TV right side panel.

Camcorder

VIDEO AUDIO

OUT

VIDEO 2 inputs on TV right side panel

To view the camcorder video:

Select the VIDEO 2 video input source on the TV.*

* To select the video input source, press INPUT on the remote control

(- page 24). To program the TV remote control to operate other

devices, see Chapter 3.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

To connect a DVI device, you will need:

• one HDMI-to-DVI adapter cable (HDMI type A connector)

per DVI device

– For proper operation, the length of an HDMI-to-DVI

adapter cable should not exceed 9.8 ft (3m). The

recommended length is 6.6 ft (2m).

Connecting an HDMI^™or DVI device

to the HDMI input

The HDMI input on your TV receives digital audio and

uncompressed digital video from an HDMI source device, or

uncompressed digital video from a DVI (Digital Visual

Interface) source device.

This input is designed to accept HDCP (High-Bandwidth

Digital-Content Protection) program material in digital form

from EIA/CEA-861-D–compliant^[1]consumer electronic

devices (such as a set-top box or DVD player with HDMI or

DVI output).

• one pair of standard analog audio cables per DVI device

– An HDMI-to-DVI adapter cable transfers video only.

Separate analog audio cables are required (see

illustration).

– See “Setting the HDMI^™audio mode” (- page 35).

TV lower back panel

TV upper back panel

The HDMI input can accept and display VGA, 480i (60Hz),

480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/

60Hz) signal formats. For detailed signal specifications, see

page 72.

Supported Audio format: Linear PCM, sampling rate 32/44.1/

48 kHz

Note: To connect a PC to the HDMI input, see page 22.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector) per HDMI device

DVI device

DVI/HDCP

OUT

VIDEO

AUDIO

– For proper operation, it is recommended that you use an

HDMI cable with the HDMI Logo (

– To display an 1080p/60Hz signal format, you will need a

Category 2 cable. Conventional HDMI/DVI cable may not

work properly.

– HDMI cable transfers both video and audio. Separate

analog audio cables are not required (see illustration).

– See “Setting the HDMI^™audio mode” (- page 35).

OUT

Note: To ensure that the HDMI or DVI device is reset properly,

it is recommended that you follow these procedures:

• When turning on your electronic components, turn on the

TV first, and then the HDMI or DVI device.

TV lower back panel

• When turning off your electronic components, turn off the

HDMI or DVI device first, and then the TV.

[1] EIA/CEA-861-D compliance covers the transmission of

uncompressed digital video with high-bandwidth digital content

protection, which is being standardized for reception of high-

definition video signals. Because this is an evolving technology, it

is possible that some devices may not operate properly with the TV.

HDMI device

VIDEO

AUDIO

HDMI OUT

OUT

HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

To view the HDMI device video:

Select the HDMI 1, HDMI 2, or HDMI 3 video input source on

the TV.*

* To select the video input source, press INPUT on the remote control

(- page 24). To program the TV remote control to operate other

devices, see Chapter 3.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

Note:

• Some audio systems may not be compatible with Dolby

Connecting a digital audio system

Digital bitstream signals. Older audio systems that are not

compatible with standard optical out signals may not work

properly, creating a high noise level that may damage

speakers or headphones. THIS DAMAGE IS NOT COVERED

BY YOUR WARRANTY.

The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby^®*

Digital g or 2-channel down-mixed PCM (pulse-code

modulation) signal for use with an external Dolby^®Digital

decoder or other external audio system with optical audio

input.

• The DIGITAL AUDIO OUT terminal may not output some

digital audio sources because of copy restrictions.

You will need:

* Manufactured under license from Dolby Laboratories.

Dolby, and the double-D symbol are registered trademarks of Dolby

Laboratories.

• optical audio cable (Use an optical audio cable that has the

larger “TosLink” connector and not the smaller “mini-

optical” connector.)

Dolby Digital decoder or

other digital audio system

Connecting an audio system

Optical

Audio IN

LINE IN

This connection allows you to use external speakers with an

external analog audio amplifier to adjust the sound level.

TV lower back panel

You will need:

• standard audio cables

Analog audio amplifier

LINE IN

To control the audio:

Turn on the TV and the digital audio device.

TV upper back panel

Press Y on the TV’s remote control and open the Audio

menu.

Highlight Audio Setup and press T.

Audio

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio Setup

To control the audio:

In the Optical Output Format field, select either

Dolby Digital/Surround or PCM, depending on your

device

(- “Selecting the optical audio output format” on

page 49).

Turn on the TV and the stereo amplifier.

Minimize the sound volume from the TV’s built-in

speakers and control the volume level using the

amplifier’s remote control.

Audio Setup

PC Audio

Auto

HDMI 1 Audio

MTS

Stereo

Language

English

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

DVD Audio

Reset

Done

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2: Connecting your TV

• Depending on the DVD’s title and the specifications of the

PC on which you are playing the DVD-Video, some scenes

may be skipped or you may not be able to pause during

multi-angle scenes.

Connecting a personal computer

(PC)

• Signal names for mini D-sub 15-pin connector

With either the PC IN or HDMI connection, you can watch

your computer’s display on the TV and hear the sound from the

TV’s speakers.

Signal

name

Signal

name

Ground 11

Ground 12

Ground 13

Signal

name

Pin No.

To connect a PC to the PC IN terminal on the TV:

When connecting a PC to the PC IN terminal on the TV, use an

analog RGB (15-pin) computer cable and a PC audio cable.

H-sync

V-sync

NC *

TV lower back panel

Ground 15

TV upper back panel

*NC=Not connected

To connect a PC to the HDMI terminal on the TV:

When connecting a PC to the HDMI terminal on the TV, use

an HDMI-to DVI adapter cable and analog audio cables.

If connecting a PC with an HDMI terminal, use an HDMI cable

(type A connector). Separate analog cables are not necessary

(- page 20).

TV upper back panel

PC audio

cable

TV lower back panel

Computer

PC audio

output

PC audio

cable

Conversion adapter

(if necessary)

Computer

• To use a PC, set the monitor output resolution on the PC

before connecting it to the TV. The following signals can be

displayed:

PC audio

output

Format

VGA

Resolution

640 × 480

800 × 600

1024 × 768

V. Frequency

60Hz

SVGA

XGA

60Hz

The HDMI input can accept and display VGA, 480i (60Hz),

480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/

60Hz) signal formats. For detailed signal specifications, see

page 72.

Other formats or non-standard signals will not be displayed

correctly.

• To display the optimum picture, use the PC setting feature

(- “Using the PC settings feature” on page 54).

Note:

• The edges of the images may be hidden.

• The PC audio input terminals on the TV are shared with the

HDMI-1 analog audio input terminals (- page 55).

• Some PC models cannot be connected to this TV.

• If receiving a 720p, 1080i, or 1080p signal program, Native

mode scales the video to display the entire picture within the

borders of the screen (i.e. no overscanning).

• An adapter is not needed for computers with a compatible

mini D-sub15-pin terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

• Always remove batteries from the remote control if they are

dead or if the remote control is not to be used for an

extended period of time. This will prevent battery acid from

leaking into the battery compartment.

Preparing the remote control

for use

Your TV remote control can operate your TV and many other

devices such as cable converter boxes, satellite receivers,

VCRs, DVD players, and HTIBs (home theater in a box), even

if they are different brands.

Remote control effective range

For optimum performance, aim the remote control directly at

the TV and make sure there is no obstruction between the

remote control and the TV.

If you have a Toshiba device:

Your TV remote control is preprogrammed to operate most

Toshiba devices (- page 27).

If you have a non-Toshiba device or a Toshiba device

that the remote control is not preprogrammed to

operate:

Point remote control

toward remote sensor

on front of TV.

You can program the TV remote control so it will operate the

other device (- pages 25–29).

Installing the remote control

batteries

16.4 ft (5m)

Remove the battery cover from the back of the remote

control.

Squeeze tab

and lift cover.

Install two “AAA” size batteries, making sure to match

the + and – signs on the batteries to the signs on the battery

compartment.

Reinsert the battery cover in the remote control until the

tab snaps.

Caution: Never throw batteries into a fire.

Note:

• Be sure to use AAA size batteries.

• Dispose of batteries in a designated disposal area.

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in

accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the

operating range becomes reduced, replace batteries with

new ones.

• When necessary to replace batteries in the remote control,

always replace both batteries with new ones. Never mix

battery types or use new and used batteries in combination.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

POWER turns the TV on and off. When the TV is on, the

Learning about the remote control

green LED indicator on the TV front will be illuminated.

PIC MODE selects the picture mode (- page 45).

SLEEP accesses the sleep timer (- page 55).

The buttons used for operating the TV only are described here.

For a complete list of the remote control’s functions, see the

remote control functional key chart (- page 26).

PIC SIZE cycles through the picture sizes: Natural,

TheaterWide 1/2/3, Full, 4:3 HD, and Native (-

page 42).

Channel Numbers (0–9, –/100) directly tune

channels. The = button is used to tune digital channels

(- page 41) or to edit the Favorites List (- page 39).

INPUT selects the video input source (- page 38).

CH Bb cycles through programmed channels when no

menu is on-screen (- page 33).

VOL + – adjusts the volume level.

FAV BROWSER accesses the Favorites List in the

Channel Brower^™(- page 39).

10 RECALL displays TV status information (- page 56).

11 CH RTN returns to the last viewed channel or source

(- page 41).

12 MUTE reduces or turns off the sound (- page 47).

13 INFO displays TV status information as well as program

details, when available. (- page 56).

14 3 C / # c While watching TV, these buttons open the

Channel Browser^™and tune to the previous/next channel

in the channel history (- page 40). (Also see “Arrow

buttons.”)

15 Arrow buttons (BbC c) When a menu is on-screen,

these buttons select or adjust programming menus. (Also

see 3 C / # c.)

16 ENTER activates highlighted items in the main menu

system.

17 MENU accesses the main TV menu system (- pages 30

and 31).

18 EXIT closes on-screen menus.

19 MODE SELECT switch switches between TV,

CABLE/SAT, AUX 1, and AUX 2 modes (- page 25).

Set to “TV” to control the TV.

You can also control the built-in DVD when the MODE

SELECT switch on the remote control is in TV mode. For

DVD operation the following buttons are used:

TOP MENU, DVD RTN, SET UP, DVD CLEAR,

PAUSE, PLAY, STOP, SKIP, REW, FF, SEARCH,

SLOW, ANGLE, SUB TITLE, AUDIO, and EJECT

(- Chapter 8).

Note: The error message “Not Available” may appear if you

press a key for a function that is not available.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

POWER Turns the selected device on and off.

Using the remote control to control

your other devices

Channel Numbers (0-9) Press to directly access

channels (as opposed to < ,).

+10 Press to directly access DVD chapters higher than 10.

If you have a non-Toshiba device or a Toshiba device that the

remote control is not preprogrammed to operate, you must first

program the remote control to recognize the device (if you

have not already done so) (- pages 27–29).

TOP MENU Accesses a DVD’s top menu.

CH Bb For channels programmed into the channel

memory (- page 41):

B selects the next higher channel.

b selects the next lower channel.

To use your TV remote control to operate a:

• Cable converter box or satellite receiver, set the MODE

GUIDE Displays the channel guide in the CABLE/SAT

SELECT switch to CABLE/SAT.

mode.

• VCR, set the MODE SELECT switch to AUX 1.

• DVD player or HTIB, set the MODE SELECT switch to

AUX 2.

SET UP Accesses a DVD’s setup menu in the AUX

mode.

INFO Displays TV status information on-screen.

Note: Even after the TV remote control is programmed, it may

not operate certain features on any other devices. If this

happens and you wish to use those features, you will need to

use the device’s original remote control.

BbC c Press to navigate DVD menus (may not work on

some DVD players).

ENTER Required by some satellite receivers and DVD

players to activate certain functions.

Point the remote control

directly at the device.

10 DVD CLEAR Press to reset the title and chapter number.

11 PLAY Begins playback of a tape or DVD.

12 PAUSE Press during play or record mode to pause the

picture; press again to restart.

13 STOP Stops the tape or DVD.

14 SKIP z Skips forward to locate later DVD chapters.

15 FF Fast-forwards the tape or DVD. (Press during play

mode to view the picture moving rapidly forward.)

16 SKIP Z Skips back to beginning of current DVD

chapter, or locates previous chapters.

17 REW Rewinds/reverses the tape or DVD. (Press during

play mode to view the picture moving rapidly backward.)

18 TV/VCR To view one program while recording another,

press to select TV mode.

SEARCH selects a specific DVD chapter, title or time.

19 REC Starts tape recording.

20 SLOW X Slow-forwards the DVD.

21 SLOW x Slow-reverses the DVD.

22 MODE SELECT switch Set to “TV” to control the TV;

“CABLE/SAT” to control a cable converter box or

satellite receiver; “AUX 1” to control a VCR; “AUX 2” to

control a DVD player or HTIB.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

Remote Control functional key chart

Note:

• “---” = key does not send a signal in that remote control mode.

• “sTV” = key will affect the TV, even though the remote control is in another mode.

• * Not available for your TV.

Toshiba TV/

REMOTE CONTROL KEY

CABLE

SAT (satellite) AUX 1 (VCR)

AUX 2 (DVD or HTIB)

Built-in DVD

Power

POWER

SLEEP

PIC SIZE

PIC MODE

1-9

Power

s TV

Digit 1-9

Digit 0

---

Power

s TV

Digit 1-9

Digit 0

100

Power

s TV

Digit 1-9

Digit 0

+10

Sleep timer

Picture size

PIC MODE

Digit 1-9

s TV

Digit 1-9

Digit 0

– (sub CH)

s TV

Digit 0

100/–/+10

INPUT

– (sub CH)

TV/Video select

s TV

FAV BROWSER/

TOP MENU

FAV BROWSER

DVD TOP Menu

---

Top Menu

MUTE

Sound mute

s TV

---

s TV

---

s TV

Setup

SET UP/GUIDE

VOL + –

DVD setup

SAT Guide

s TV

Volume up/down

s TV

Channel

up/down

Channel

up/down

Channel

up/down

Channel

up/down

---

CHBb

RECALL

s TV

DVD Return

Previous channel

DVD previous menu

CH RTN/DVD RTN

---

INFO

Info

---

Info

---

Display

Enter

ENTER

Enter

Select, Enter

Menu up/down

---

Menu up/down

Menu left

up/down

Menu left/

Menu left

C 3

Channel Browser^™

Menu right/

---

Menu right

Action Menu

Exit

---

Menu right

DVD Menu

DVD Clear

c #

Channel Browser^™

Exit

DVD clear

EXIT/DVD CLEAR

PAUSE/STEP

PLAY

Pause

---

Pause

Play

Pause

Play

STOP

Stop

SKIP Z

SKIP z

REW

Skip REV

Skip FWD

Rewind

Fast FWD

---

Skip REV

Skip FWD

Rewind

Fast FWD

---

Rewind

Fast FWD

TV/VCR/

DVD search

---

TV/VCR

DVD search

REC

REC MENU*

SLOW REW

SLOW FWD

Angle

---

Record (2 click) ---

SLOW –

SLOW +

ANGLE

SUB TITLE

AUDIO

EJECT

---

DVD Angle

DVD Sub title

DVD Audio

DVD Eject

Sub title

Audio

Eject

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

Programming the remote control

to control your other devices

Your Toshiba TV remote control is preprogrammed to operate

most Toshiba devices. To program your TV remote control to

operate a non-Toshiba device (or a Toshiba device that it is not

preprogrammed to operate), follow the steps below. For details

on using the remote control to operate the device, see page 25.

In the remote control code table (- page 28), find the

code for your device. If more than one code is listed, try

each one separately until you find one that works.

Set the MODE SELECT switch to the type of device

you are programming the remote control to operate —

CABLE/SAT (for a cable converter box or satellite

receiver), AUX 1 (for a VCR or TV/VCR combo), or

AUX 2 (for a DVD player or HTIB [home theater in a

box]).

While holding down E, press the Channel Number

buttons to enter the 3-digit code for your device.

To test the code, turn on the device, point the remote

control at it, and press p. See notes below.

• If the correct code was entered, the device will turn off.

• If the device does not respond, repeat steps 1–4 using

another code.

• If the device does not respond to another code, you will

need to use the remote control that came with the

device.

Remember to set the MODE SELECT switch back to

“TV” to control the TV.

For future reference, write down the code(s) you used:

DEVICE

CODE

DEVICE

CODE

Note:

• In addition to POWER, confirm that all necessary keys on the

TV remote control operate your device. If some keys are not

operational, repeat the device code setup using another

code (if other codes are listed for your device). If, after trying

all listed codes, the necessary keys do not operate your

device, use the device’s original remote control.

• Every time you change the batteries, you will need to

reprogram the remote control.

• Some newer VCRs respond to either of two codes. These

VCRs have a switch labeled “VCR1/VCR2.” If your VCR has

this kind of switch and does not respond to the codes for

your VCR brand, set the switch to the other position (“VCR1”

or “VCR2”) and reprogram the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

Drake

020, 040, 044, 046,

050, 053

018, 041, 051

057

Clarion

Classic

Daewoo

Denon

Emerson

Fisher

Funai

Go Video

GPX

019

020

021

Remote control codes

Echostar

Express Vu

Fujitsu

022, 023, 024, 025

026, 027

028

027

001, 029, 030

087

031

027

In some cases you may not be able to

operate your device with the TV

remote control. Your other device may

use a code that is not recognized by the

TV remote control. If this happens, use

the device’s remote control.

008, 009, 013

010, 011, 012, 022,

023, 031, 049

033

General Instruments

Hitachi

Hughes

033

Hughes Network

Systems

Intersat

Janeil

JVC

Hitachi

005, 032, 033, 034,

035

003, 007, 036, 042,

088

037

008, 009

004, 038

039

040

026

041

043

044

058

010, 045, 046, 047,

048, 049, 050

004, 051

052, 053, 054, 055

001, 056

057, 058

001, 002, 059, 089

060

061, 062, 086, 090

073

063, 091

064, 067

074

019

048

027

017, 057

029

060

058

036, 052

JVC

Cable converter box

Kenwood

Konka

Magnavox

Memorex

Mintek

ABC

061, 062, 063, 082,

084, 087, 092, 096,

098

Kenwood

Magnavox

Optimus

Pansat

Primestar

Proscan

Radio Shack

RCA

Realistic

Samsung

Sony

Star Choice

Star Trak

STS

Archer

065, 092, 097, 099

064, 094

092

090, 092, 097

083, 085, 086, 088,

093, 098

Cableview

Century

Citizen

015, 042

NAD

008, 009, 013

022, 023, 030

008, 009, 013, 016

030

059

014, 055

057, 106

025, 026, 037, 054

024

000, 001, 002, 003,

004, 005, 006, 007,

020, 031, 056

021, 028, 030, 032,

035, 039, 043, 045,

047, 058

Nakamichi

Norcent

Onkyo

Oritron

Panasonic

Contec

Diamond

093

061, 062

Gemini

Hamlin

069, 070, 094

093

Philips

Pioneer

Proscan

Qwestar

RCA

Sampo

Samsung

Sansui

Sanyo

Hitachi

Jasco

062, 095, 096

097

Toshiba

Motorola/GI/Jerrold

062, 069, 071, 082,

086, 089, 096, 107

072, 096

092, 104

090

101

081, 083, 085

087

Magnavox

Memorex

Multi Canal

Novavision

Panasonic

Philco

Uniden

Zenith

027

Sharp

Sherwood

Sony

011, 012, 065, 066,

068, 069, 070

027

071

072

Philips

066, 067, 068, 070,

072, 073, 074, 075,

092

TV/VCR Combo

Action

Sylvania

Teac

Technics

Techwood

Toshiba

078

059, 062

065

078

065

079

074

057

Pioneer

076, 077

Goldstar

Panasonic

Precision

Quasar

Realistic

Sony

Toshiba

Zenith

Totevision

Proscan

061, 062

075

Radio Shack

RCA

092, 097, 099

064, 081

000, 013, 076, 077,

078

079, 080, 081

014, 082, 092

Realistic

065

Yamaha

Zenith

Recoton

102

Samsung

Scientific Atlanta

077, 090

063, 078, 079, 080,

088, 098, 101, 105

095

065

009, 010, 065

Portable DVD player

Aiwa

Audiovox

Panasonic

RCA

Sears

093

Signature

Signature 2000

Sprucer

062

096

081, 085

094, 095

024, 096, 099

098

DVD/VCR Combo

Go Video

DVD=087,

VCR=081

DVD=088,

VCR=082

DVD=089,

VCR=083

DVD=090,

VCR=084

DVD=091,

VCR=085

DVD=092,

VCR=086

Starcom

069, 082, 087, 096,

103, 104

JVC

Stargate

069, 090

VCR

Admiral

Aiko

Aiwa

Akai

Sylvania

095, 100

RCA

049

019

018

TeleView

Texscan

090

100

Samsung

Sanyo

Zenith

Tocom

071, 084, 085

087, 096, 098

082

065, 092, 097, 099,

102, 103

003, 004, 037, 038,

039, 058, 069

010

007, 068

008, 017

U. S. Electronics

United Cable

Universal

Audiovox

Bell & Howell

Broksonic

Calix

Wards

096

010

Carver

CCE

Citizen

026

019

DVD player

Aiwa

Apex

BOSE

Broksonic

Satellite receiver

Alphastar

Chaparral

DISH Network

009, 010, 011, 012,

013, 014, 015, 019,

057, 073

006, 015

016, 017

097

038, 059

034

057

Colortyme

005

018

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3: Using the remote control

Craig

009, 010, 016, 061,

065, 079

001, 005, 009, 012,

014, 040, 048, 053,

056, 057

011, 013, 015, 017,

018, 019, 057, 078

078

Orion

054, 057, 062, 065,

068, 072

Video Concepts

Wards

005, 006, 011, 012,

039, 053

Curtis Mathes

Panasonic

Pentax

036, 045, 046, 057,

061, 072, 079

012, 024, 025, 035,

042, 053, 063

014

026, 027, 063

026, 031, 044, 057

006, 024, 043, 055

012, 013, 015

001, 002, 048

061

009, 010, 011, 016,

018, 020, 024, 025,

031, 035, 049, 051,

056, 057, 060, 065,

066, 079

Daewoo

Pentex Research

Philco

Philips

Pioneer

Portland

Proscan

Proton

Quasar

Radio Shack

Radio Shack/Realistic

Daytron

Denon

Dimensia

Electrohome

Emerson

White Westinghouse

XR-1000

Yamaha

073

018

063

001, 048

005, 006, 007, 014,

037, 053

004, 032, 034, 041,

047, 069, 086

010, 020, 065

003, 008, 010, 011,

017, 018, 020, 028,

039, 054, 057, 062,

065, 068, 072

007, 016, 021, 022,

023, 057, 064, 068,

070, 071, 079

004, 041

Zenith

045

010, 031, 065

007, 009, 010, 016,

018, 020, 021, 022,

031, 049

HTIB

Lasonic

Panasonic

Venturer

Fisher

083

084

085

Fuji

Radix

RCA

010

Funai

Garrard

018, 073

018

001, 002, 003, 009,

024, 025, 029, 035,

040, 042, 045, 048,

055, 056, 063, 071,

083

007, 009, 010, 011,

016, 018, 020, 021,

022, 031, 049, 051,

056, 060, 065, 075,

079

001, 002, 009, 040,

042, 048, 056

056, 059, 061, 081

005, 010, 014, 054,

056, 065, 067

018, 065

Go Video

Goldstar

Realistic

Gradiente

Harman Kardon

Hitachi

005

024, 025, 035, 037,

042, 063, 070, 080

076

Ricoh

Runco

047

034

JBL

JC Penney

005, 006, 007, 008,

009, 010, 023, 024,

025, 026, 035, 056,

061, 063, 065

024, 025, 037, 050

005, 006, 007, 014,

037, 043, 055, 062,

063, 068, 082

005, 006, 007, 012,

014, 037, 043, 050,

053, 068, 071

010

Samsung

009, 011, 038, 056,

073, 084

006, 037, 043, 061

007, 009, 016, 054,

064, 068, 071, 075,

079, 085

008, 011, 017, 028,

030, 057, 065, 072

007, 010, 016, 021,

022, 023, 024, 025,

035, 053, 057, 063,

064, 065, 068, 071,

075, 079

Sansui

Sanyo

Jensen

JVC

Scott

Sears

Kenwood

Kodak

010

Lloyds

Logik

LXI

Magnasonic

Magnavox

053, 073, 079

061

010

Sharp

013, 020, 031, 049,

051, 060, 066

004, 025, 032, 061

049

075

047, 061

004, 032, 033, 041,

052, 058, 070, 074,

076, 077, 080

035

018, 026, 027, 028,

044, 072

Shintom

Signature

Signature 2000

Singer

061, 065, 078

026, 027, 034, 044,

057, 061, 072

005, 006, 007, 012,

014, 026, 053, 067

007, 009, 010, 016,

018, 034, 049, 063,

065, 066, 068, 075,

079

Marantz

Sony

Memorex

STS

Sylvania

MGA

MGN

020, 028, 039

056

Symphonic

018, 050, 051, 053,

073, 079

Minolta

Mitsubishi

024, 025, 035, 063

020, 024, 025, 028,

039, 043, 065

049

Tandy

007

010

037

018, 029, 037

036

010, 018, 065

000, 011, 021, 023,

024, 028, 030, 039,

057, 074, 078, 079

009, 010, 065

073

Tashiko

Tatung

Teac

Technics

Teknika

Toshiba

Montgomery Ward

Motorola

MTC

Multitech

NEC

049

009, 046, 061

009, 012, 018

005, 006, 007, 012,

014, 037, 043, 053,

054, 067, 070

010

Totevision

Unitec

Nikko

Noblex

Optimus

Optonica

009

010, 049, 065

031

Unitech

Vector Research

009

005, 006, 011, 012,

053

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4: Menu layout and navigation

Main menu layout

The tables below and on the next page provide a quick overview of your TV’s menu system.

To open the main menus (illustrated below), press Y on the remote control or TV control panel.

Icon

Item

Option

Mode

S Sports/Standard/Movie/Preference

S [Opens the Picture Settings menu]

S [Opens the Noise Reduction menu]

S On/Off

Video

Picture Settings

Noise Reduction

Game Mode

Theater Settings

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio Setup

S [Opens the Theater Settings menu]

S [Launches the temporary Audio Selector]

S [Opens the Audio Settings menu]

S [Opens the Advanced Audio Settings menu]

S [Opens the Audio Setup menu]

S [Launches the temporary CC Selector]

S Off/CC1/CC2/CC3/CC4/T1/T2/T3/T4

S [Opens the Digital CC Setup menu]

S [Opens the Input Labeling menu]

S [Opens the Channel Labeling menu]

S English/French/Spanish

Audio

CC Selector

Preferences

Base CC Mode

Digital CC Settings

Input Labeling

Channel Labeling

Menu Language

Channel Browser Setup

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

S [Opens the Channel Browser Setup menu]

S Off/On

Locks

S [Opens the Edit Rating Limits menu]

S [Opens the Channels block menu]

S Off/Video/Video+

Front Panel Lock

New PIN Code

Installation

S Off/On

S [Opens the New PIN Code entry screen]

S [Opens the Installation menu (- page 31)]

S [Opens the Sleep Timer menu]

S [Opens the PC Settings menu]

Setup

Sleep Timer

PC Settings

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4: Menu layout and navigation

Setup/Installation menu layout

The Installation menu contains the Terrestrial and System Status menus.

To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu,

select Installation, and press T.

Icon

Item

Option

Press Y,

open the

Setup menu,

and then

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

S [Opens the Input Configuration menu]

S [Start] S [Scans for new channels on ANT]

S [Opens the Channel Add/Delete menu]

S [Opens the Signal Meter menu]

Terrestrial

open the

Installation

sub-menu.

System Status

System Information

S [Opens the System Information screen]

Note:

• The menu background may sometimes appear black,

depending on the signal the TV is receiving. This is not a

sign of malfunction.

Navigating the menu system

You can use the buttons on the remote control or TV control

panel to access and navigate your TV’s on-screen menu

system.

Video

• Press Y to open the menu system.

Mode

Sports

Off

Picture Settings

Noise Reduction

Game Mode

• When a menu is open, use the up/down/left/right arrow

buttons (BbC c) on the remote control or TV control panel

to move in the corresponding direction in the menu.

Theater Settings

• Press T to save your menu settings or select a highlighted

item. (A highlighted menu item appears in a different color

in the menu.)

• All menus close automatically if you do not make a selection

within 60 seconds, except the signal meter menu, which

closes automatically after about 5 minutes.

Navigate

ENTER

CH RTN

Back

EXIT Exit

Select

• The Video sub-menu appears with a black background,

which looks different from other menus.

Picture Settings

Mode: Sports

Contrast

Back Light

DynaLight

Brightness

Color

100

• To close a menu instantly, press O.

Tint

Sharpness

Advanced Picture Settings

Reset

Done

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

Selecting the menu language

Configuring the antenna input

source for the ANT terminal

You can choose from three different languages (English,

French and Spanish) for the on-screen display of menus and

messages.

To configure the ANT input source:

To select the menu language:

Press Y and open the Setup menu.

Highlight Installation and press T.

Press Y and open the Preferences menu.

Highlight Menu Language and press c.

Press B or b to select your preferred menu language and

press T.

Setup

Installation

Sleep Timer

PC Settings

Preferences

(A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight

Input Configuration, and press T.

CC Selector

Base CC Mode

Off

Digital CC Settings

Input Labeling

Channel Labeling

Menu Language

Channel Browser Setup

Installation

English

Français

Español

English

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Press O to close the Preferences menu.

Press C or c to select the input source (Cable or

Antenna) for the ANT input on the TV.

Input Configuration

Antenna In

Cable

Done

Cancel

To save your new settings, highlight Done and press T.

To revert to your original settings, highlight Cancel and

press T.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

(A new set of Installation menu icons will appear, as

Programming channels into the

TV’s channel memory

shown below.) Open the Terrestrial menu, highlight

Channel Program to bring up the Start, and press T

again to begin channel programming.

When you press < or , on the remote control or TV control

panel, your TV will stop only on the channels you programmed

into the TV’s channel memory.

Follow the steps below to program channels into the TV’s

channel memory.

Installation

Terrestrial

Input Configuration

Start

Channel Program

Channel Add/Delete

Signal Meter

Programming channels automatically

ANT

Cable

Your TV can automatically detect all active channels in your

area and store them in its memory. After the channels are

programmed automatically, you can manually add or erase

individual channels in the channel memory.

Scanning channels, please wait ...

52%

Number of Channels Found - 73

Scanning Digital Channels

Found Channel - 118

Abort

Note:

• You must configure the antenna input source before

The TV will automatically cycle through all the antenna

channels, and store all active channels in the channel

memory. While the TV is cycling through the channels,

the message “Scanning channels, please wait” appears (as

shown above).

programming channels (- page 32).

• If the Antenna input signal type is set to Cable, the automatic

channel programming process erases channels that were

previously programmed into the TV’s memory.

• If the Antenna input signal type is set to Antenna, the

automatic channel programming process adds newly found

channels to the existing set of programmed channels (and

does NOT erase channels that were previously

programmed into the TV’s memory.) To remove an Antenna

source channel from the memory, you must manually delete

it.

To cancel channel programming, press O on the remote

control (or highlight Abort in the on-screen display and

press T).

When channel programming is finished, press < or , to

view the programmed channels.

• To tune the TV to a channel not programmed in the channel

memory, you must use the Channel Number buttons on the

remote control.

• Programming channels when the antenna input is

configured for Cable will take substantially longer than when

the antenna input is configured for Antenna. This is normal;

however, once channel programming is finished, you should

not have to repeat the programming process again unless

your Cable TV service lineup changes significantly.

Manually adding and deleting channels

in the channel memory

After automatically programming channels into the channel

memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

Press Y and open the Setup menu.

To program channels automatically:

Highlight Installation and press T.

(A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight

Channel Add/Delete, and then press T.

Configure the antenna input source, if you have not

already done so (- page 32).

Press Y and open the Setup menu.

Highlight Installation and press T.

Installation

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Setup

Installation

Sleep Timer

PC Settings

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you

want to add, and then press T to check the box.

Labeling channels

A list of common channel labels (logos) for various channels

(ABC, CBS, etc.) will be programmed into the TV. You will

be able to view and assign these logos from the Channel

Labeling window. If the desired channel label is not provided

in the list, you will be able to manually enter/edit labels using

the software keyboard.

To manually add digital subchannels on a physical

channel:

Use the Channel Numbers and the Dash (=) on the remote

control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and

the box will be checked.

To assign channel labels:

If the channel is not found, a message will appear.

Press Y and open the Preferences menu.

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you

want to remove, and then press T to uncheck the box.

Highlight Channel Labeling and press T.

The Channel Labeling window opens.

To save your new settings:

Highlight Done and press T.

Preferences

CC Selector

Off

CC1

CC2

CC3

CC4

Base CC Mode

Off

To revert to your original settings:

Highlight Cancel and press T before saving.

Digital CC Settings

Input Labeling

Channel Labeling

Menu Language

Channel Browser Setup

English

To remove all channels from the channel memory:

Highlight Reset and press T, and then highlight Done and

press T.

Channel Labeling

{No Label}

ANT

Channel Add/Delete

A&E

Press CH UP/DOWN to

change channels.

Analog

Digital

Analog

Digital

Analog

Digital

Analog

2 - 1

2 - 2

ABC

ABCFAM

ABCHD

AMAX

AMAXW

AMC

Custom

Clear All

Done

ANIMAL

Reset

Cancel

Done

Press < or , to select the channel you want to label.

7 - 1

Press BbC c to highlight the desired channel label and

press T.

To remove encrypted channels from the channel

memory:

If an encrypted channel is accidentally added to the channel list

by programming channels, you can remove the unwanted

encrypted (non-viewable) channel while you are channel

surfing. When you tune to an encrypted channel, the following

message will appear.

Repeat steps 3 and 4 for other channels.

To save your settings, highlight Done and press T.

Channel Labeling

{No Label}

ANT

A&E

Press CH UP/DOWN to

change channels.

ABC

ABCFAM

ABCHD

AMAX

Digital Channel Is Encrypted - Press 1 on remote to remove channel

AMAXW

AMC

Custom

Clear All

Done

ANIMAL

Press “1” button while the message is on the screen to

remove the unnecessary channel from the channel list.

The maximum number of labels that can be stored is 128.

To remove channel labels:

Open the Channel Labeling window.

Press < or , to select the channel for which you want to

remove the label.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

Press BbC c to highlight No Label and press T.

Highlight Yes from the deletion confirmation window

and press T.

Channel Labeling

{No Label}

Channel Labeling

ANT

A&E

TIMES

TLC

ANT

ABC

ABCFAM

ABCHD

AMAX

Press CH UP/DOWN to

change channels.

TMC

TMCX

TMCXw

TMCw

Delete the selected custom label?

Press CH UP/DOWN to

change channels.

Yes

AMAXW

AMC

Custom

Clear All

Done

TNT

Custom

Clear All

Done

ANIMAL

TNTHD

TOCDEFG

Repeat steps 2 and 3 for other channels.

Highlight Done and press T to save changes, and go

back to the Channel Labeling window.

To save your settings, highlight Done and press T.

If the desired channel label is not available from the list of

presets, you can create a custom label.

Setting the HDMI^™audio mode

To create and assign a custom label:

To set the HDMI audio mode:

Open the Channel Labeling window.

Press < or , to select a channel you want to label.

Press Y and open the Audio menu.

Press Bb c to highlight Custom and press T.

The software keyboard will appear.

Highlight Audio Setup and press T.

Press B or b to select HDMI 1 Audio and then press C

or c to select the HDMI 1 audio mode (Auto, Digital, or

Analog). (Auto is the recommended mode.) See

“Connecting an HDMI or DVI device to the HDMI input”

(- page 20).

Channel Labeling

{No Label}

ANT

A&E

Edit CH RTN Cancel

Send EXIT Exit

ABC

Press CH UP/DOWN to

O m

ABCFAM

change channels.

ABCHD

Backspace

INPUT Space

100

AMAX

Audio Setup

AMAXW

AMC

PC Audio

Auto

Clear All

Done

ANIMAL

HDMI 1 Audio

MTS

Stereo

Repeatedly press the corresponding key on the remote

control to highlight the desired character on the on-screen

software keyboard.

Language

English

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

The highlighted character is entered after you either press

a different key, press c key, or after a two-second pause.

DVD Audio

Reset

Done

Repeat steps 4 and 5 until you have entered all desired

text.

Note: Because the PC and HDMI-1 inputs share the same set

of analog audio inputs, the PC Audio menu setting influences

the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the

HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to

“Yes,” the HDMI 1 Audio setting is set to “Digital” and is

grayed out in the menu. (Also see item 4 on page 14 and

“Setting the PC Audio” on page 55.)

When finished, press T.

(New labels will be added to the list in alphabetical order

and marked with an icon to indicate that they are

custom.) Highlight the new custom label and press T to

assign. Assigned channel labels will be displayed in the

banner, Channel Add/Delete window, and Channels

Block window.

To delete the custom label:

Open the Channel Labeling window.

Highlight the label to be deleted and press =.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

Viewing the digital signal meter

Viewing the system status

You can view the digital signal meter in the ANT digital TV

input source only.

To view the system status:

Press Y and open the Setup menu.

To view the digital signal meter:

Highlight Installation and press T.

Press Y and open the Setup menu.

A new set of Installation menu icons will appear, as shown

below. Open the System Status menu, highlight

System Information, and press T.

Highlight Installation and press T.

A new set of Installation menu icons will appear, as shown

below. Open the Terrestrial menu, highlight Signal

Meter, and press T.

Installation

System Status

System Information

Installation

Terrestrial

Press C c to scroll through the menu bar to select the

Software Version and view the related information.

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

System Information

Software Version

LV07

3.2.21.0

Nov 17 2006 - 01:52:20

FW: 0B

Press BbC c to select the antenna input and digital

channel whose signal you want to check.

Note: The physical digital channel number listed in the

Signal Meter screen may not correspond to a virtual TV

channel number. Contact your local broadcasters to

obtain the RF channel numbers for your local digital

stations.

Done

To close the screen and return to the Installation

menu:

Highlight Done and press T.

Signal Meter

To return to normal viewing:

Signal Locked

Press O.

Peak

Physical Digital Channel

Virtual Digital Channel

4-1

Advanced

Done

To close the screen and return to the Terrestrial

menu:

Highlight Done and press T.

To return to normal viewing:

Press O.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5: Setting up your TV

Reset Factory Defaults

To reset all settings and channels to their factory

default values:

Press Y and open the Setup menu.

Highlight Installation and press T. A new set of

Installation menu icons will appear.

Open the System Status menu, highlight System

Information, and press T.

Press C c to scroll through the menu bar to select

Factory Defaults.

System Information

Factory Defaults

This window provides the ability to reset the TV

settings.Type in your PIN now (or "0000" if no

PIN has been set) to restore settings to their

factory default values.

Done

Enter your PIN code (or 0000 if no PIN code has been set).

Highlight Yes and press T. The TV will turn off

automatically after a few seconds. After the TV turns off,

unplug the TV power cord and then plug it in again to

complete the reset process.

System Information

Press YES to confirm. After the TV

turns off, unplug it and plug it back

in to complete the reset.

Yes

To cancel the reset:

Highlight No and press T.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Selecting the video input source

Labeling the video input sources

to view

You can label each video input source according to the type of

device you connected to each source, from the following preset

list of labels:

To select the video input source to view:

• – – (default label)

• Audio Receiver

• Cable

• Compact Disc

• DTV

• DVD

• Game Console

• HD DVD

Press + on the remote control or TV control panel.

And then either:

a) Press 0–9; or

b) Repeatedly press Bb on the remote control and then

press T to change the input; or

c) Repeatedly press + on the remote control or TV

control panel to change the input.

The current signal source displays in the top right corner

of the Input Selection screen.

• Laser Disk

• Satellite/DSS

• VCR

Input Selection

ANT

• Video Recorder

Built-In DVD

Video 1

•

Hide (to hide an unused input in the Input Selection screen)

Video 2

ColorStream HD1

ColorStream HD2

HDMI 1

Note: If you select Built-In DVD or PC in the Input Selection

screen, you can choose only “– –” or “Hide” as the label.

HDMI 2

HDMI 3

To label the video input sources:

INPUT

to Select

Navigate

Press Y and open the Preferences menu.

Note:

Highlight Input Labeling and press T.

• You can label the video input sources according to the

specific devices you have connected to the TV

(- “Labeling the video input sources” at right).

Press B or b to highlight the video source you want to

label.

• Sources can also be “hidden” (- “Labeling the video input

sources” at right).

Preferences

CC Selector

• “No Video Signal” will appear randomly on the screen if no

signal is received in video input mode.

Off

CC1

CC2

CC3

CC4

Base CC Mode

Off

Digital CC Settings

Input Labeling

Channel Labeling

Menu Language

Channel Browser Setup

English

Input Labeling

Built-In DVD

Video 1

VCR

Video 2

Cable

ColorStream HD 1

ColorStream HD 2

HDMI 1

Video Recorder

Hide

DTV

HDMI 2

Satellite/DSS

HDMI 3

DVD

Reset

Done

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Press C or c to select the desired label for that input

Tuning channels

source. If a particular input is not used, you can select

Hide as the label, which will cause that input to be

“grayed out” in the Input Selection screen and skipped

over when you press + on the remote control.

Tuning channels using the

Channel Browser^™

To save the new input labels, highlight Done and press

To revert to the factory default labels, highlight Reset

and press T.

The Channel Browser^™provides an easy navigation interface

for all your channels and inputs. This feature allows you to:

• Navigate the contents of all of your inputs.

Input labeling example:

• Keep a list of your favorite channels (see “Favorites

Browser,” below).

• Keep a history of the last 32 channels or inputs viewed.

• Quickly surf and tune your recently viewed channels/inputs

from the Channel Browser^™History List (illustrated on the

next page).

• Surf via Browse mode (to immediately tune channels as you

highlight them in the Channel Browser^™) or Select mode (to

surf over channels in the Channel Browser^™before you

select one to tune).

The screen below left shows the default Input Selection

screen (with none of the inputs labeled as a specific device).

The screen below right is an example of how you could label

the inputs if you connected a VCR to VIDEO 1, Cable TV to

VIDEO 2, a video recorder to ColorStream HD1, a DTV set-

top box to HDMI 1, a satellite/DSS set-top box to HDMI 2, and

a DVD player to HDMI 3. Also note that the ColorStream HD2

input is labeled “Hidden,” which means that input will be

skipped over when + is pressed.

Input Selection

ANT

Input Selection

ANT

• Quickly change inputs from the Inputs List.

ANT

Built-In DVD

Video 1

Built-In DVD

VCR

Favorites Browser

Video 2

Cable

ColorStream HD1

ColorStream HD2

HDMI 1

Video Recorder

The Favorites Browser allows you to quickly set up a favorite

ColorStream HD2 (Hidden)

channels/inputs list that is integrated into the Channel Browser^™.

DTV

HDMI 2

Satellite/DSS

DVD

HDMI 3

To add a favorite channel/input:

INPUT to Select

Navigate

INPUT

to Select

Navigate

Tune to the channel or input.

Input Selection screen with

no inputs labeled.

Input Selection screen with

all inputs labeled except input 5,

which has been hidden.

Press and hold n for 3 seconds.

Note: Additions are added to the beginning of the Favorites list

on the left side of the Channel Browser^™.

To clear the input labels:

To delete a favorite channel/input:

Press Y and open the Preferences menu.

Highlight Input Labeling and press T.

Press n to open the Favorites browser list.

Highlight Reset and press T.

Highlight the channel or input to delete by pressing

3 C or # c.

Press and hold = for 3 seconds. The channel/input will

be removed from the Favorites list.

To set up the Channel Browser^™:

Press Y and open the Preferences menu.

Highlight Channel Browser Setup and press T.

Press B to highlight Navigation, and then press C or c

to select either Browse Mode or Select Mode.

Channel Browser Setup

Navigation

History List

ANT List

Select Mode

Power Off Clear (On)

Inputs List

Favorites List

Reset

Done

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Note:

Press b to highlight History List, and then press C or c

• The Channel Browser^™opens in History List by default.

Once another list has been selected, the Channel Browser^™

will open in the last selected list.

to select the setting you prefer: either Power Off Clear

(On), On, or Off.

Note: When History List is set to On, the channels and

inputs stored in the list will be saved every power on/off

cycle. When History List is set to Power Off Clear (On),

the channels and inputs stored in the list will be cleared

with every power on/off cycle of the TV.

• If all lists are turned off, pressing 3 C, #c, or n will not

display the Channel Browser^™. If Favorites List is turned

off, n will have no effect.

• PressingnwillbringuptheChannelBrowser^™Favorites

list regardless of the last selected list in the

Channel Browser^™.

Press b to highlight ANT List, and then press C or c to

select On or Off.

To tune to a channel or input in Browse mode:

Press b to highlight Inputs List, and then press C or c

to select On or Off.

While watching TV, press 3 C or # c to open the

Channel Browser^™and surf back to a previous item or

surf forward to the next item in the list.

Press b to highlight Favorites List, then press Cor c to

select On or Off.

To save your entries, highlight Done and press T.

To return to factory defaults, highlight Reset and

press T.

In Browse mode, when you stop on an item in the

Channel Browser^™, it will be highlighted and the TV will

automatically tune to the channel or input.

Press O to close the Channel Browser^™.

To open the Channel Browser^™:

To tune to a channel or input in Select mode:

• Press 3 C or # c on the remote control.

• Press 3 C to surf backward through the previously tuned 32

channels in the History list, the channels in the ANT channel

list, the inputs in the Inputs list, or the favorite channels/

inputs in Favorites list.

• Press # c to surf forward through the channel History, the

ANT channel list, the Inputs list, or the favorite channels/

inputs in Favorites list.

While watching TV, press 3 C or # c to open the

Channel Browser^™and surf back to a previous item or

forward to the next item in the list.

In Select mode, when you stop on an item in the Channel

Browser^™, it will be highlighted but you must press T to

tune the TV to the highlighted item.

Press T to tune the TV to the highlighted item.

Press O to close the Channel Browser^™.

Note: To access the Channel Browser™ while on the Built-In

DVD input, first press E then press 3 C, # c or n.

Elements of the Channel Browser^™

Adding and clearing channels and inputs in the

History List

History

Adding channels and inputs to the History List:

As a channel or input is tuned, the Channel Browser^™adds it

to the History List and displays it on the “right side” of the

Channel Browser^™. Previously tuned channels/inputs are

“shifted” to the left, eventually moving off the left side. Press

3 C to surf backward through the previously tuned channels/

inputs. Any channel or input that is tuned repeatedly will not

be repeated in the History List, but instead is moved to the end

of the list on the right side of the Channel Browser^™.

The Channel Browser^™will store the following channels:

• All channels that are tuned using the numeric buttons on the

remote control.

TVLAND

ABCHD

WEATHER

Current list (History, ANT, Inputs, or Favorites)

Input type

Channel or input currently being viewed

Channel or input that is currently highlighted in the

browser

• All channels that are tuned using < or , on the remote

Channels stored in the History List

Channel labels

control.

Note: Whenever an item is selected that cannot be tuned (for

various reasons), the TV will automatically tune to the

previously viewed channel or input.

To toggle among the available lists:

After opening the Channel Browser^™, press B or b to toggle

among History, ANT, Inputs, and Favorites.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Clearing channels from the History List:

• Reconfiguring the ANT input will clear the History List.

Switching between two channels using

SurfLock^™

Note: See page 32 for details on configuring the antenna

input.

The SurfLock^™feature temporarily “memorizes” one channel

to the R button, so you can return to that channel quickly

from any other channel by pressing R. To memorize a

channel to the R button:

• Once 32 channels or inputs are stored in the History List, the

oldest item will be removed from the list when a new

channel or input is tuned.

Tune the TV to the channel you want to program into the

R button.

• If History List in the Channel Browser Setup is set to

“Power Off Clear (On),” turning off the TV will clear the

History List.

Press and hold R for about 2 seconds until the message

“Channel Memorized” appears on-screen. The channel

has been programmed to the R button.

Tuning to the next programmed channel

You can then change channels repeatedly, and when you

press R, the memorized channel will be tuned.

To tune to the next programmed channel:

Press < or , on the remote control or TV control panel.

The TV will return to the memorized channel one time only.

Once you press R and then change channels again, the CH

RTN memory will be cleared and the button will function as

Channel Return, by switching back and forth between the last

two channels that are tuned. This feature also works for

external inputs.

Note:This feature will not work unless you program channels

into the TV’s channel memory (- page 33).

Tuning to a specific channel (programmed

or unprogrammed)

Tuning analog channels:

Press the Channel Number (0–9) on the remote control. For

example, to select channel 125, press 1, 2, 5.

Tuning digital channels:

Press the Channel Number (0–9) on the remote control,

followed by the dash (=) button and then the sub-channel

number. For example, to select digital channel 125-1, press 1,

2, 5, –, 1.

Note: If a digital channel is not programmed—either through

the automatic channel scan (- page 33) or the channel add/

delete function (- page 33)—you will have to tune the RF

channel using the Channel Number and dash (=) on the

remote control.

Switching between two channels using

Channel Return

The Channel Return feature allows you to switch between two

channels without entering an actual channel number each time.

Select the first channel you want to view.

Select a second channel using the Channel Number

buttons (and the dash (=) button if selecting a digital

channel).

Press R on the remote control. The previous channel

will display. Each time you press R, the TV will switch

back and forth between the last two channels that were

tuned.

Note: If you press R from a non-antenna input, the TV

will return to the last-viewed input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Note: If you select one of the TheaterWide^®picture sizes, the

top and bottom edges of the picture (including subtitles or

captions) may be hidden. To view the hidden edges, either

scroll the picture (TheaterWide 2 and 3 only) or try viewing the

program in Full or Natural picture size.

Selecting the picture size

You can view many program formats in a variety of picture

sizes—Natural, TheaterWide 1, TheaterWide 2,

TheaterWide 3, Full, 4:3 HD and Native.

Natural picture size

• The image is displayed close to its originally formatted

proportion. Some program formats will display with

sidebars and/or bars at the top and bottom.

Note: The “picture size” illustrations are examples only. The

format of the image (in any of the picture sizes) will vary

depending on the format of the signal you are currently

watching. Select the picture size that displays the current

program the way that looks best to you.

You can save separate picture size preferences for each input

on your TV.

To select the picture size using the remote control:

Press I on the remote control.

Natural picture size example

While the Picture Size screen is open, you can do one of

the following to select the desired picture size:

TheaterWide 1 picture size (for 4:3 format programs)

• Repeatedly press I.

• Press the corresponding Number button (0–6) while the

Picture Size screen is open.

• The center of the picture remains close to its original

proportion, but the left and right edges are stretched wider to

fill the screen.

• Press B or b while the Picture Size screen is open.

Picture Size

Natural

TheaterWide 1

TheaterWide 2

TheaterWide 3

Full

TheaterWide 1 picture size example

4:3 HD

Native

TheaterWide 2 picture size (for letter box programs)

PIC SIZE

to Select

• The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

• The top and bottom edges of the picture may be hidden. To

view the hidden areas, see “Scrolling the TheaterWide^®

picture” (- page 43).

To select the picture size using the menus:

Select Picture Size in the Theater Settings menu.

Press C or c to select the desired picture size setting.

Highlight Done and press T.

Theater Settings

Mode: Sports

Picture Size

Full

Picture Scroll

A B C D E F G - - - - - - - - - - - - - - - -

Cinema Mode

Auto Aspect Ratio

DVD Aspect Ratio

Film

TheaterWide 2 picture size example

16:9 Wide

Reset

Done

Note: Some of the picture sizes may not be available

depending on the receiving signal format (those will be

“grayed out” in the Picture Size screen).

Using these functions to change the picture size (i.e.,

changing the height/ width ratio) for any purpose other than

your private viewing may be prohibited under the Copyright

Laws of the United States and other countries, and may

subject you to civil and criminal liability.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Note:

TheaterWide 3 picture size (for letter box programs

with subtitles)

• Native picture size is available for 720p, 1080i, and 1080p

signals only. If the signal being received is other than 1080i,

1080p, or 720p, “Native” will be grayed out in the Picture

Size screen.

• The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

• The top and bottom edges are hidden. To view the hidden

areas (such as subtitles or captions), see “Scrolling the

TheaterWide^®picture.”

• This mode is supported only for HDMI and ColorStream

inputs.

• Depending on the input signals, the border of the picture

may be hidden, displayed in black, or noisy.

A B C D E F G - - - - - - - - - - - - - - - -

A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -

TheaterWide 3 picture size example

Native picture size example

Full picture size (for 16:9 [480i, 480p] source

programs only)

Scrolling the TheaterWide^®picture

(TheaterWide 2 and 3 only)

• If receiving a squeezed 4:3 format program, the picture is

stretched wider to fill the width of the screen, but not

stretched taller.

• None of the picture is hidden.

You can set separate scroll settings for the TheaterWide 2 and

TheaterWide 3 modes for each input.

To set the scroll settings:

Press Y and open the Video menu.

Highlight Theater Settings and press T.

Full picture size example

4:3 HD picture size (for 720p, 1080i, and 1080p

program sources only)

• Sidebars fill the empty vertical spaces.

• Picture is not distorted from original size.

Video

Mode

Sports

Off

Picture Settings

Noise Reduction

Game Mode

Theater Settings

In the Picture Size field, select either TheaterWide 2

or TheaterWide 3 (you cannot scroll in any other mode).

Press b to highlight the Picture Scroll field.

Press C or c to scroll the picture up and down as needed,

from –10 to +20.

4:3 HD picture size example

Native picture size (for 720p, 1080i, and 1080p signal

programs)

• If receiving a 720p, 1080i, or 1080p signal program, Native

mode scales the video to display the entire picture within the

borders of the screen (i.e. no overscanning).

Mode: Sports

TheaterWide 2

Theater Settings

Picture Size

Picture Scroll

Cinema Mode

-5

Film

Auto Aspect Ratio

DVD Aspect Ratio

16:9 Wide

• This is especially useful for external HD sources such as

HD-DVD, DVHS movies, or PC graphics.

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Using the auto aspect ratio feature Selecting the cinema mode

(480i and 1080i signals)

When the auto aspect ratio feature is set to On, the TV will

automatically select the picture size when one of the following

When you view a DVD (3:2 pulldown processed) from a DVD

input sources is received:

player connected to the VIDEO 1, VIDEO 2, ColorStream

• A 480i signal from the VIDEO 1, VIDEO 2, ColorStream

HD-1, or ColorStream HD-2 input.

• A 480i, 480p, 720p, 1080i, 1080p, or VGA signal from the

HDMI input.

HD-1, ColorStream HD-2 (component video), or HDMI

inputs on the TV, smoother motion can be obtained by setting

the Cinema Mode to Film.

To set the Cinema Mode to Film:

Aspect ratio of Automatic aspect size (automatically

signal source selected when Auto Aspect is On)

Press Y and open the Video menu.

Highlight Theater Settings and press T.

In the Cinema Mode field, select Film.

4:3 normal

Natural (with sidebars)

4:3 letter box TheaterWide 2

16:9 full

Full

Mode: Sports

Theater Settings

Not defined

Picture Size

Natural

(no ID-1 data The current picture size you set under

Picture Scroll

or HDMI

aspect data)

“Selecting the picture size” on page 42.

Cinema Mode

Auto Aspect Ratio

DVD Aspect Ratio

Film

16:9 Wide

Note: The auto aspect ratio feature is not applicable to

antenna or cable input sources.

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

To turn on the auto aspect ratio feature:

Press Y and open the Video menu.

To set the Cinema Mode to Video:

Select Video in step 3 above.

Highlight Theater Settings and press T.

In the Auto Aspect Ratio field, select On.

Mode: Sports

Theater Settings

Picture Size

Natural

Picture Scroll

Cinema Mode

Film

Auto Aspect Ratio

DVD Aspect Ratio

16:9 Wide

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

To turn off the auto aspect ratio feature:

Select Off in step 3 above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Adjusting the picture quality

You can adjust the picture quality (Contrast, Back Light,

DynaLight™, Brightness, Color, Tint, and Sharpness) to your

personal preferences.

Adjusting the picture

Selecting the picture mode

You can select your desired picture settings from four different

modes, as described below.

Selection

Contrast

Back Light*

DynaLight**

Brightness

Color

Pressing C

lower

Pressing c

higher

darker

On/Off

darker

paler

lighter

Mode

Picture Quality

On/Off

lighter

Sports

Standard

Bright and dynamic picture (factory setting)

Standard picture settings (factory setting)

deeper

Lower contrast for darkened room (factory

setting)

Movie

Tint

reddish

softer

greenish

sharper

Preference

Your personal preferences

Sharpness

To select the picture mode:

Press u on the remote control.

The following popup menu appears on-screen.

* Back Light

This feature adjusts the brightness of the entire screen. When in

video mode and no signal is input, this will automatically be set to 0.

(Settings are stored in memory.)

**DynaLight

This function automatically strengthens the black coloring of dark

areas in the video according to the level of darkness.

Sports

Standard

Movie

To adjust the picture quality:

Preference

Press Y and open the Video menu.

Press B or b to select the picture mode you prefer and

press T.

Highlight Picture Settings and press T.

Press B or b to select the picture quality you want to

adjust (Contrast, Back Light, DynaLight,

Brightness, Color, Tint, or Sharpness), and then

press C or c to adjust the setting, as described in the table

above.

To select the picture mode using the menu system:

Press Y and open the Video menu.

Highlight Mode and press T.

Picture Settings

Mode: Sports

Contrast

100

Back Light

DynaLight

Brightness

Color

100

Video

Mode

Sports

Picture Settings

Noise Reduction

Tint

Off

Game Mode

Sharpness

Advanced Picture Settings

Theater Settings

Reset

Done

Press B or b to select the picture mode you prefer and

press T.

Picture Settings

Mode: Preference

Contrast

Sports

To save the new settings, highlight Done and press T.

Standard

Movie

You can use any of the picture modes (- “Selecting the

picture mode,” above left) as a starting point for adjusting

the picture settings.

Preference

Note: The picture mode you select affects the current

input only. You can select a different picture mode for

each input.

To revert back to the base mode that you began adjusting

the picture settings from, highlight Reset and press T.

The picture qualities you adjusted are automatically saved in

the Preference mode (- “Selecting the picture mode,”

above left) until Reset is selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Note: A closed caption signal may not display in the following

situations:

Using the closed caption mode

• When a videotape has been dubbed

• When the signal reception is weak

• When the signal reception is non-standard

Base closed captions

The closed caption mode has two options:

• Captions—An on-screen display of the dialogue, narration,

and sound effects of TV programs and videos that are closed

captioned (usually marked “CC” in program guides).

• Text—An on-screen display of information not related to

the current program, such as weather or stock data (when

provided by individual stations).

Digital CC Settings

You can customize the closed caption display characteristics

by changing the background color, opacity, text size, type,

edge, and color.

Note:

• This feature is available for digital channels only.

• You cannot set the Caption Text and Background as the

same color.

To view captions or text:

Press Y and open the Preferences menu.

To customize the closed captions:

Highlight Base CC Mode and press c.

Press Y and open the Preferences menu.

Press Bor bto select the desired closed caption mode and

press T.

Highlight Digital CC Settings and press T.

Press B or b to highlight the characteristic you want to

change, and then press C or c to select the format for that

characteristic (see table below).

Preferences

CC Selector

Off

CC1

CC2

CC3

CC4

Base CC Mode

Off

Digital CC Settings

Input Labeling

Caption Size

Auto

Channel Labeling

Menu Language

Caption Text Type

Caption Text Edge

Caption Text Color

Text Foreground Opacity

Background Color

English

Auto

Channel Browser Setup

Auto

Text Background Opacity

Caption Text Edge Color

Auto

• To view captions:

Highlight CC1, CC2, CC3, or CC4. (CC1 displays

translation of the primary language in your area.)

Auto

ABC123

Preview

window

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Caption Size

Auto, Small, Standard, Large

Giant pandas eat leaves.

Auto, Default, Mono w. Serif, Prop. w.

Serif, Mono w/o Serif, Prop. w/o Serif,

Casual, Cursive, Small Capitals

Note: If the program or video you selected is not closed

Caption Text

Type

captioned, no captions will display on-screen.

• To view text:

Highlight T1, T2, T3, or T4.

Caption Text

Edge

Auto, None, Raised, Depressed, Uniform,

Left Drop Shadow, Right Drop shadow

Caption Text

Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

WORLD WEATHER

Temps

Current

Weather

Clear

LONDON

MOSCOW

PARIS

Text Foreground Auto, Transparent, Translucent

Opacity

Cloudy

Clear

Cloudy

Rain

ROME

Flashing, Solid

TOKYO

Background

Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

Note: If text is not available in your area, a black rectangle

may appear on screen. If this happens, set the Base CC

Mode to Off.

Text Background Auto, Transparent, Translucent

Opacity

• To turn off the closed caption mode:

Select Off in step 3 above.

Flashing, Solid

Caption Text

Edge Color

Auto, Black, White, Red, Green, Blue,

Yellow, Magenta, Cyan

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

CC Selector

Adjusting the audio

You can use the CC Selector to temporarily override the

default analog caption mode (set in Base CC Mode) for a

particular channel. However, once you change to another

analog channel, the closed caption setting will automatically

change back to the current Base CC Mode setting.

Muting the sound

Press W to partially reduce (1/2 MUTE) or turn off (MUTE)

the sound. Each time you press W, the mute mode will change

in the following order:

You can also use the CC Selector to select digital closed

caption services (if available). When such services are not

available, the CC Selector presents a default list of services.

If the selected service is not available, the next best service will

be used instead.

1/2 Mute

Mute

Volume

If the closed caption mode is set to Off when you select

“MUTE” mode, the closed caption feature is automatically

activated. To mute the audio without automatically activating

the closed caption feature, use Z to set the volume to 0. See

“Using the closed caption mode” (- page 46) for more

information on closed caption modes.

To select closed captions:

Press Y and open the Preferences menu.

Highlight CC Selector and press T.

Using the digital audio selector

Preferences

CC Selector

You can use the Digital Audio Selector to conveniently

switch between audio tracks on a digital channel (for those

channels that have multiple audio tracks). This temporarily

overrides the audio track chosen by the language option under

Audio Setup (- “Selecting stereo/SAP broadcasts” on

page 48).

Off

CC1

CC2

CC3

CC4

Base CC Mode

Off

Digital CC Settings

Input Labeling

Channel Labeling

Menu Language

English

Channel Browser Setup

Press B or b to select Closed Caption, and then press

To use the digital audio selector:

C or c to select the desired service.

Press Y and open the Audio menu.

Closed Caption

CC 1

None

Audio

Highlight Digital Audio Selector and press T.

Press O.

Audio

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio Setup

Press B or b to select Audio, and then press C or c to

select the desired service.

Closed Caption

CC 1

None

Audio

Press O.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

To listen to a second audio program on an analog

station (if available):

Select SAP in step 3 above.

Selecting stereo/SAP broadcasts

The multi-channel TV sound (MTS) feature allows you to

output high-fidelity stereo sound. MTS also can transmit a

second audio program (SAP) containing a second language,

music, or other audio information (when provided by

individual stations).

Note:

• A second audio program (SAP) can be heard only on those

TV stations that offer it. For example, a station might

broadcast another language as a second audio program. If

you have SAP on, you will see the current program on the

screen but hear the other language instead of the program’s

normal audio.

When the TV receives a stereo or SAP broadcast, the word

“STEREO” or “SAP” appears on-screen when E is pressed.

The MTS feature is not available when the TV is in VIDEO

mode.

• If you have SAP on and the station you are watching is not

broadcasting a second audio program, the station’s normal

audio will be output. However, occasionally there is no

sound at all in SAP mode. If this happens, set the MTS

feature to Stereo mode.

To listen to stereo sound:

Press Y and open the Audio menu.

Highlight Audio Setup and press T.

Adjusting the audio quality

You can adjust the audio quality by adjusting the bass, treble,

and balance.

Audio

Digital Audio Selector

Audio Settings

Advanced Audio Settings

To adjust the audio quality:

Audio Setup

Press Y and open the Audio menu.

In the MTS field, select Stereo.

Highlight Audio Settings and press T.

Audio Setup

PC Audio

Auto

Press b or B to highlight the item you want to adjust

(Bass, Treble, or Balance).

HDMI 1 Audio

MTS

Stereo

Audio Settings

Language

English

Bass

100

Optical Output Format

Dolby Digital/Surround

Treble

Dolby Digital

Dynamic Range Control

Compressed

Stereo

Balance

StableSound

DVD Audio

Reset

Off

Done

Reset

Press C or c to adjust the level.

To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight

Reset and press T.

• C makes the bass or treble weaker or increases the

balance in the left channel (depending on the item

selected).

• c makes the bass or treble stronger or increases the

balance in the right channel (depending on the item

selected).

Note:

• You can typically leave the TV in Stereo mode because

it will automatically output the type of sound being

broadcast (stereo or monaural).

• If the stereo sound is noisy, select Mono to reduce the

noise.

To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight

Reset and press T.

To listen to an alternate language on an ATSC digital

station (if available):

Highlight the Language field in step 3 above, and then press

C or c to select the language you prefer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Using the StableSound^®feature

In the Optical Output Format field, select either

Dolby Digital/Surround or PCM, depending on your

The StableSound^®feature limits the highest volume level to

prevent extreme changes in volume when the signal source

changes (for example, to prevent the sudden increase in

volume that often happens when a TV program switches to a

commercial).

device.

Audio Setup

PC Audio

Auto

HDMI 1 Audio

MTS

Stereo

Language

English

To turn on the StableSound^®feature:

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

Press Y and open the Audio menu.

Highlight Audio Settings and press T.

In the StableSound field, select On.

Audio Settings

DVD Audio

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Bass

100

Treble

Balance

StableSound

Note: You cannot change the optical audio output format while

you are viewing a DVD. (You must be in FULL-STOP mode, not

RESUME-STOP mode.)

Done

Reset

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Using the Dolby^®Digital Dynamic Range

Control feature

This dynamic range control feature causes the ATSC dynamic

range to be further compressed, allowing you to switch from

ATSC to analog broadcasts at the same dynamic range.

Note: The RESET function returns your audio adjustments

to the following factory settings:

Bass . . . . . . . . center (50)

Treble . . . . . . . center (50)

Balance . . . . . . center (0)

StableSound . . Off

To use the Dolby Digital Dynamic Range Control:

Press Y and open the Audio menu.

To turn off the StableSound feature:

Select Off in step 3 above.

Highlight Audio Setup and press T.

In the Dolby Digital Dynamic Range Control field,

select Compressed. When Standard is selected, the

audio is output with minimal compression.

Selecting the optical audio output format

You can use this feature to select the optical audio output

format when you connect a Dolby Digital decoder or other

digital audio system to the Optical Audio Out terminal on

the TV (see “Connecting a digital audio system” on page 21).

Audio Setup

PC Audio

Auto

HDMI 1 Audio

MTS

Stereo

Language

English

To select the optical audio output format:

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

Press Y and open the Audio menu.

DVD Audio

Reset

Highlight Audio Setup and press T.

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note:

• This item will be grayed out for NTSC signals, Video,

ColorStream, and PC inputs.

• The Dolby Digital Dynamic Range Control will function in

relation to Optical Output Format (PCM mode).

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

When the correct PIN code is entered, the Locks menu opens.

Using the Locks menu

The Locks menu includes the Enable Rating Blocking, Edit

Rating Limits, Channels Block, Input Lock, Front (control)

Panel Lock, and New PIN Code features. You can use these

features after entering the correct PIN code.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Front Panel Lock

New PIN Code

Entering the PIN code

Press Y and highlight the Locks menu icon.

If you cannot remember your PIN code

While the PIN code entering screen is displayed, press E

four times within five seconds. The PIN code will be cleared

and you can enter a new PIN code.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Changing your PIN code

Front Panel Lock

New PIN Code

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

Enter your four-digit PIN code and press T.

Press b to highlight New PIN Code and press T.

Press b, which displays the PIN code entry screen.

• The Lock System screen (below) appears if a PIN

code has not been stored. Press the Channel Number

buttons to enter a new four-digit code, enter the code a

second time to confirm, and press T.

Lock System

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Please enter a 4 digit PIN code

Off

Confirm PIN code

Front Panel Lock

New PIN Code

Cancel

Done

Press the Number buttons to enter a new four-digit code.

Reenter the PIN code to confirm it.

• The Locks/Active screen (below) appears if the PIN

code is already stored. Use the Number buttons to enter

your four-digit code and press T.

Press T. The new PIN code is now active.

New PIN Code

Locks

Active

Please enter a 4 digit PIN code

Please enter the 4 digit PIN code

Confirm PIN code

Cancel

Done

Cancel

Done

If the wrong PIN code is entered, the message “Incorrect PIN

code, please try again!” appears. Highlight Retry and press

T. Enter the code again and press T.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Blocking TV programs and movies

by rating (V-Chip)

Some TV programs and movies include signals that classify

the content of the program (violence, sex, dialog, language).

The V-Chip feature in this TV detects the signals and blocks

the programs according to the ratings you select. (For rating

descriptions, see the tables on the next page.)

Downloading an additional rating system

for blocking TV programs and movies

In the future, an additional rating system may become

available for use in selectively blocking programs.

Note: The currently tuned station must be receiving a digital

signal before an additional rating system can be downloaded.

To download the additional rating system

(if available):

Note: Rating blocking is a function of the V-Chip feature in this

TV, which supports the U.S. V-Chip system only.

To block and unblock TV programs and movies:

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

Enter your four-digit PIN code and press T.

Press b to highlight Enable Rating Blocking.

Press c and b to select On, and press T.

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

Enter your four-digit PIN code and press T.

Press b to highlight Enable Rating Blocking.

Press c and b to select On, and then press T.

Press b to highlight Edit Rating Limits and press T.

The Edit Rating Limits screen appears.

Highlight Alt RS and press T. The Edit Alternate

Ratings screen will appear.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Note:

• The Alt RS button will only be available if an additional

rating system is currently available.

• It may take several minutes for the TV to download the

additional rating system.

Off

Front Panel Lock

New PIN Code

Press b to highlight Edit Rating Limits and press T.

The Edit Rating Limits screen (below) appears.

• The information displayed in the Alternate Ratings

screen will depend on the configuration of the

additional rating system available at the time of

download.

Press BbC c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will

be blocked. As you highlight a rating, a definition for the

rating appears at the bottom of the screen.

Press B b C c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will

be blocked.

When done selecting the ratings you want to block,

highlight Done and press T.

When you are finished selecting the ratings you want to

block, highlight Done and press T.

Edit Rating Limits

Movies

TV (V-CHIP) FV

TV-Y

10 In the Edit Rating Limits screen, highlight Done and

Children

Youth

press T.

TV-Y7

TV-G

PG-13

Note:

TV-PG

TV-14

TV-MA

NC-17

Alt RS

Cancel

Done

• The additional rating system can only be downloaded one

time. You will not be able to download any updates to the

rating system should such updates become available.

"None" Rated

• The additional rating system is not designed, transmitted, or

controlled by the TV or Toshiba, nor is the availability of an

additional rating system determined or controlled by

Toshiba. Similarly, the rating of programs in an additional

rating system is not determined, transmitted, or controlled

by the TV or Toshiba.

• The additional rating system is an evolving technology;

therefore, availability, content, and format may vary.

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Blocking channels

With the Channels Block feature, you can block specific

channels. You will not be able to tune blocked channels unless

you unlock them.

Independent rating system for broadcasters

Ratings

Description and Content themes

Mature Audience Only (This program is specifically

designed to be viewed by adults and therefore may

be unsuitable for children under 17.)

L) Crude or indecent language S) Explicit sexual

activity V) Graphic violence

TV-MA

To block channels:

Parents Strongly Cautioned (This program contains

some material that many parents would find

unsuitable for children under 14 years of age.)

D) Intensely suggestive dialog L) Strong, coarse

language S) Intense sexual situations V) Intense

violence

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

TV-14

Enter your four-digit PIN code and press T

(- page 50).

Press b to highlight Channels Block and then press T.

Parental Guidance Suggested (This program

contains material parents may find unsuitable for

younger children.)

D) Some suggestive dialog L) Infrequent coarse

language S) Some sexual situations V) Moderate

violence

A list of the channels available for that input will be

displayed along with the call letters for each channel, if

available.

TV-PG

TV-G

General Audience (Most parents would find this

program suitable for all ages.)

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Directed to Older Children (This program is designed

for children age 7 and above. Note: Programs in

which fantasy violence may be more intense or more

combative than other programs in this category are

designated TV-Y7FV.)

TV-Y7,

TV-Y7FV

Off

Front Panel Lock

New PIN Code

All Children (This program is designed to be

appropriate for all children.)

TV-Y

Press Bb to highlight the channel you want to block and

press T, which puts an “5” in the box next to that

channel.

Independent rating system for movies

Channels Block

Ratings

NC-17

Description and Content themes

X-rated (For adults only)

Not intended for anyone 17 and under

Restricted (Under 17 requires accompanying parent

or adult)

Parents Strongly Cautioned (Some material may be

inappropriate for children under 13)

Allow All

Block All

Cancel

Done

PG-13

Parental Guidance Suggested (Some material may

not be suitable for children)

General Audience (Appropriate for all ages)

Repeat step 5 for other channels you want to block.

Highlight Done and press T.

Note:

• If you place an“ 5” in the box next to “ ‘None’ Rated,”

programs rated “None” will be blocked; however, programs

that do not provide any rating information will not be

blocked.

• To display the rating of the program you are watching, press

E on the remote control. If it is rated “None,” the word

“NONE” appears in the RECALL screen (as shown below

right). If rating information is not provided, no rating will

appear in the RECALL screen.

To unblock individual channels:

In step 5 above, press Bb to highlight the channel you want to

unblock, press T to remove the “5” from the box, highlight

Done and press T.

TV - PG

NONE

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

To block all channels at once:

Highlight Block All in step 5 on previous page and then

highlight Done and press T.

Using the input lock feature

You can use the Input Lock feature to lock the video inputs

(Built-In DVD, VIDEO 1, VIDEO 2, ColorStream HD-1,

ColorStream HD-2, HDMI 1, HDMI 2, HDMI 3 and PC)

and channels 3 and 4. You will not be able to view the input

sources or channels until you unlock the inputs.

To unblock all locked channels at once:

Highlight Allow All in step 5 on previous page and then

highlight Done and press T.

To lock/unlock the video inputs:

Channels Block

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

Enter your four-digit PIN code and press T.

Press b to highlight Input Lock and press c.

Allow All

Block All

Cancel

Done

Press B or b to select the level of video input locking you

prefer, as described below.

Video: Locks Built-In DVD, VIDEO 1, VIDEO 2,

ColorStream HD1/HD2, HDMI 1, HDMI 2, HDMI 3, and

PC.

Video+: Locks Built-In DVD, VIDEO 1, VIDEO 2,

ColorStream HD1/HD2, HDMI 1, HDMI 2, HDMI 3, PC

and channels 3 and 4.

Unlocking programs temporarily

If you try to tune the TV to a program that exceeds the rating

limits you set, the TV will enter program lock mode and the

following message will appear on-screen:

• Select Video+ if you play video tapes via an ANT

input.

This program exceeds the rating limit you set.

Push 'mute' to enter PIN.

You can either temporarily unlock the program or select an

unlocked program to watch.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

To temporarily unlock the program:

Off

Press W.

Front Panel Lock

New PIN Code

Video

Video +

Off

Enter your four-digit PIN code and press T. If the correct

code is entered, the program lock mode is released and the

normal picture appears. All locking is disabled until the

TV is turned off, and will be enabled when the TV is

turned on again.

Off: Unlocks all video inputs and channels 3 and 4.

Press T.

Locks

Active

Enter PIN code to temporarily unblock.

Cancel

Done

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Using the control panel lock feature

Using the PC settings feature

You can lock the control panel to prevent your settings from

being changed accidentally (by children, for example). When

the control panel lock is On, none of the controls on the TV

control panel will operate except POWER.

You can view an image from a PC on the TV screen.

When a PC is connected to the TV's PC IN terminal, you can

use the PC Settings feature to make adjustments to the image.

If the edges of the picture are cut off, readjust the Horizontal

Position and Vertical Position. If the picture is affected by

interference, readjust the Clock Phase and Sampling

Clock.

To lock the control panel:

Press Y and highlight the Locks menu icon.

Press b to display the PIN code entering screen.

Enter your four-digit PIN code and press T.

Press b to highlight Front Panel Lock.

To adjust the PC settings:

Repeatedly press + to select PC input mode

(- “Selecting the video input source to view” page 38).

Press c and C or c to highlight On and press T. When

the control panel is locked and any button on the control

panel (except POWER) is pressed, the message “Not

Available” appears.

Press Y and open the Setup menu.

Highlight PC Settings and press T.

Locks

Setup

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Off

Installation

Sleep Timer

PC Settings

Off

Front Panel Lock

New PIN Code

Off

Note: If a PC is not connected or there is no pc input

signal, this feature will be grayed out in the Setup menu.

Press B or b to highlight the item you want to adjust.

Press C or c to make the appropriate adjustments.

PC Settings

To unlock the control panel:

Highlight Off in step 5 above, or press and hold the

VOLUME – button on the TV control panel for about 10

seconds until the volume icon appears.

Horizontal Position

Vertical Position

Clock Phase

Sampling Clock

Reset

Done

Note: The screen is disrupted momentarily when

adjusting the PC settings. This is not a sign of malfunction.

• Horizontal Position:

Moves the picture left/right.

The adjustment range is within 10 from center.*

• Vertical Position:

Moves the picture up/down.

The adjustment range is within 10 from center.*

• Clock Phase:

Helps to reduce noise and sharpen the picture.

The adjustment range is within 4 from center.*

• Sampling Clock:

Helps to reduce noise and minimize periodic vertical stripes

on the screen.

The adjustment range is within 5 from center.*

* The default settings may vary depending on the input signal format.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Setting the PC Audio

Setting the sleep timer

This function allows you to output the sound from your PC (if

connected) or mute the sound from your PC and output the

sound from your HDMI (DVI) connection. (- page 20)

You can set the sleep timer to turn off the TV after a set length

of time (maximum of 180 minutes).

To set the sleep timer using the remote control:

To set the PC Audio:

Press [ on the remote control to set the length of time until

the TV turns off. Repeatedly press [ to increase the time in

10-minute increments, or press B or b to increase or decrease

the time in 10-minute increments, to a maximum of 180

minutes.

Press Y and open the Audio menu.

Highlight Audio Setup and press T.

Press B or b to select PC Audio and then press C or c

to select No or Yes.

To set the sleep timer using the on-screen menus:

Yes: Outputs the sound from your PC.

No: Mutes the sound from your PC, and outputs the

sound from the HDMI-1 connection.

Press Y and open the Setup menu.

Highlight Sleep Timer and press T.

Audio Setup

PC Audio

Auto

HDMI 1 Audio

MTS

Setup

Stereo

Installation

Sleep Timer

PC Settings

Language

English

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

Press the Number buttons to enter the length of time in

10-minute increments.

DVD Audio

Reset

Done

Sleep Timer

Note: Because the PC and HDMI-1 inputs share the same

set of analog audio inputs, the PC Audio menu setting

influences the HDMI 1 Audio menu setting. If PC Audio is

set to “No,” the HDMI 1 Audio setting changes to “Auto.”

If PC Audio is set to “Yes,” the HDMI 1 Audio setting is

set to “Digital” and is grayed out in the menu. (Also see

item 4 on page 14 and “Setting the HDMI^™Audio mode”

on page 35.)

Enter total minutes until the TV

turns off automatically (Maximum

180 minutes)

1 2 0

Cancel

Done

Highlight Done and press T.

Note: When a power failure occurs, the sleep timer setting

may be cleared.

To display the remaining sleep time:

Press [.

Sleep Timer

120 minutes

Note: A message will display on-screen when there is one

minute remaining on the sleep timer.

To cancel the sleep timer:

Repeatedly press [ until it is set to 0 minute.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6: Using the TV’s features

Displaying TV status information

Understanding the auto power off

feature

To display TV status information using RECALL:

Press E on the remote control.

The following information will display (if applicable):

• Current input (ANT, VIDEO 1, etc.)

• If ANT is the current input, either “CABLE” (for cable TV)

or “ANT” (for over-the-air broadcasts).

The TV will automatically turn itself off after approximately

15 minutes if it is tuned to a vacant channel or a station that

completes its broadcast for the day. This feature functions in

ANT mode and Built-In DVD mode (No disc) only.

• Channel number (if in ANT mode)

• Channel label (if set)

• Digital signal strength indicator (bar graph in lower right

corner of box; for ATSC signal only)

Understanding the last mode

memory feature

• Stereo, Mono or SAP audio status (when HDMI input mode,

Dolby Digital or PCM)

• Video resolution

If the power is cut off while you are viewing the TV, the

Last Mode Memory feature automatically turns on the TV

when the power is resupplied.

• Aspect ratio of incoming video signal (4:3 or 16:9)

• V-Chip rating status

Note: You should unplug the TV’s power cord if it is possible

that you will be away from the TV for an extended period of time

after the power is restored.

12^A3^N-^T456

16:9

Stereo SAP

1080i

TV-PG

9:00pm

ABCHD

To close the RECALL screen:

Press E again.

To display TV status information using INFO:

Press Q on the remote control.

The following additional information will display for off air

digital channels (if applicable):

• Title

• Duration

• Detailed description

12^A3^N-^T456

16:9

Stereo SAP

1080i

TV-PG

East

MLB Young s XXX...

9:00pm -11:00pm

ABCHD

Today s Major League Baseball.

Note: The location of the banner can be moved to the top or

bottom of the screen by pressing B or b while the RECALL or

INFO display is on-screen. (The last position will be stored to

memory.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7: Using the TV’s advanced features

Using the static gamma feature

The static gamma feature allows you to adjust the levels of

black in the picture.

Using the advanced picture settings

features

To adjust the static gamma settings:

Using dynamic contrast

Press Y and open the Video menu.

When dynamic contrast is set to Low, Middle, or High, the

TV will detect changes in the picture quality that affect the

appearance of your contrast settings and then automatically

adjust the video.

Highlight Picture Settings and press T.

Video

Mode

Sports

Off

To select dynamic contrast preferences:

Picture Settings

Noise Reduction

Press Y and open the Video menu.

Game Mode

Theater Settings

Highlight Picture Settings and press T.

Highlight Advanced Picture Settings and press T.

Picture Settings

Mode: Sports

Video

Contrast

Back Light

DynaLight

Brightness

Color

100

Mode

Sports

Off

Picture Settings

Noise Reduction

Game Mode

Theater Settings

Tint

Sharpness

Advanced Picture Settings

Highlight Advanced Picture Settings and press T.

Reset

Done

Picture Settings

Mode: Sports

In the Static Gamma field, press C or c to adjust the

static gamma.

The adjustment range is within 5 from center.

Contrast

Back Light

DynaLight

Brightness

Color

100

Advanced Picture Settings

Mode: Preference

Tint

Dynamic Contrast

Sharpness

High

Static Gamma

Advanced Picture Settings

Color Temperature

Cool

Reset

Done

Reset

Done

In the Dynamic Contrast field, select either Off, Low,

• If the setting is moved in the minus direction, the detail

of black colors will be decreased.

• If the setting is moved in the plus direction, the detail of

black colors will be increased.

Middle or High.

Advanced Picture Settings

Dynamic Contrast

Mode: Preference

Off

Static Gamma

Color Temperature

Cool

To save the new settings, highlight Done and press T.

To revert the factory defaults, highlight Reset and

press T.

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: If you select one of the factory-set picture modes

(Sports, Standard or Movie) and then change the static

gamma setting, the picture mode automatically changes

to Preference.

Note: If you select one of the factory-set picture modes

(Sports, Standard, or Movie) and then change the

dynamic contrast setting, the picture mode automatically

changes to Preference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7: Using the TV’s advanced features

Selecting the color temperature

You can change the quality of the picture by selecting from

three preset color temperatures (Cool, Medium, and Warm), as

described below.

Using CableClear^®digital noise reduction

The CableClear^®digital noise reduction feature allows you to

reduce visible interference in your TV picture. This may be

useful when receiving a broadcast with a weak signal

(especially a Cable channel) or playing a noisy video cassette

or disc.

Mode

Picture Quality

blueish

Cool

To change the CableClear settings:

Medium

Warm

neutral

Press Y and open the Video menu.

reddish

Highlight Noise Reduction and press T.

To select the color temperature:

Press Y and open the Video menu.

Video

Mode

Highlight Picture Settings and press T.

Highlight Advanced Picture Settings and press T.

Highlight Color Temperature and press T.

Sports

Picture Settings

Noise Reduction

Off

Game Mode

Theater Settings

Advanced Picture Settings

Mode: Preference

In the CableClear field, select your desired setting.

Dynamic Contrast

High

Static Gamma

Noise Reduction

ANT

Color Temperature

Cool

CableClear

Auto

Reset

Done

Low

MPEG Noise Reduction

Reset

Done

In the Color Temperature field, select the mode you

prefer (Cool, Medium, or Warm).

Note:

Color Temperature

Mode: Preference

Cool

• If the current input is ANT, VIDEO 1, or VIDEO 2, the

menu will display the text “CableClear.” The available

selections are Off, Auto, Low, Middle, and High.

• If the current input is ColorStream HD1, ColorStream

HD2, HDMI 1, HDMI 2, or HDMI 3 the menu will display

the text “DNR.” The available selections are Off, Auto,

Low, Middle, and High. Auto will react proportionally

to the strength of the noise. Low, Middle, and High will

reduce the noise in varying degrees, from lowest to

highest, respectively.

Color Temperature

B Drive

G Drive

Reset

Done

Press B or b to select either B Drive or G Drive, and

then press C or c to adjust the settings.

B Drive

G Drive

• B Drive: c makes the picture blueish.

• G Drive: c makes the picture greenish.

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: The B Drive and G Drive settings are connected to

the Color Temperature settings and will change based

on which setting is selected in step 5 above.

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: If you select one of the factory-set picture modes

(Sports, Standard, or Movie) and then change the color

temperature mode, the picture mode automatically

changes to Preference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7: Using the TV’s advanced features

Using MPEG noise reduction

Using the Game Mode feature

The MPEG noise reduction feature allows you to reduce

visible interference caused by MPEG compression. Choices

for MPEG noise reduction are Off, Low, Middle, and High.

Off is automatically selected when this feature is disabled

(“grayed out”).

You can use the Game Mode feature for shorter frame delays

when playing a video game requiring split-second timing

between the on-screen display and input from the controller

(such as music creation and high-action games).

This feature is more effective for 480i and 1080i input signals.

Note: To use the Game Mode feature, the current video input

must be Video 1, Video 2, ColorStream HD1,

ColorStream HD2, HDMI 1, HDMI 2, or HDMI 3. The Game

Mode cannot be turned on when any other video input is

selected.

To select the MPEG noise reduction level:

Press Y and open the Video menu.

Highlight Noise Reduction and press T.

Press B or b to highlight the MPEG Noise Reduction

field, and then press C or c to select either Off, Low,

Middle or High.

To turn on Game Mode:

Press Y and open the Video menu.

Noise Reduction

ANT

Press Bor bto highlight the Game Mode field, and then

press C or c to select On.

CableClear

Auto

Low

MPEG Noise Reduction

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Video

Mode

Sports

Picture Settings

Noise Reduction

Off

Game Mode

Theater Settings

To turn off Game Mode:

Select Off in step 2 above, change the video input, or turn the

TV off and then on again.

Note: You can change the video input by pressing + on the

remote control (- page 38).

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7: Using the TV’s advanced features

Using the advanced audio settings

features

Using the SRS WOW^™surround sound

feature

SRS WOW^™is a special combination of SRS Labs audio

technologies (SRS 3D, SRS Focus, and SRS TruBass) that

creates a thrilling surround sound experience with deep, rich

bass from stereo sound sources. Your TV’s audio will sound

fuller, richer, and wider.

To adjust the WOW^™settings:

Put the TV in STEREO mode (-“Selecting stereo/SAP

broadcasts” on page 48).

Press Y and open the Audio menu.

Highlight Advanced Audio Settings and press T.

Press b or B to highlight the WOW feature you want to

adjust, and then press C or c to adjust the item.

Advanced Audio Settings

WOW: SRS 3D

Off

WOW: SRS Focus

WOW: SRS TruBass

Low

Reset

Done

• WOW: SRS 3D — To turn the surround sound effect

On or Off.

Note: If the broadcast is monaural, the SRS 3D effect

will not work.

• WOW: SRS Focus — To turn the vocal emphasis effect

On or Off.

• WOW: SRS TruBass — To select the desired bass

expansion level (Off, Low, or High).

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

WOW, SRS and l symbol are trademarks of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

Resume feature

• Depending on the disc you are playing, when you press D

one time, the TV memorizes the location where playback is

stopped. Press S to resume the playback from the stopped

location.

Playing a disc

Be sure to set the MODE SELECT switch on the remote

control to TV mode when using the Built-In DVD input.

• If you press D again or eject the disc, the TV will clear the

stopped location.

DVD VCD

Basic playback

Auto Play feature

If you load a disc when the TV is off, the TV will power on and

playback will commence automatically. However, loading the

disc may take 1-2 seconds.

Press p on the TV or on the remote control to turn on

the TV.

Press + on the remote control or INPUT on the TV to

select the Built-In DVD mode.

The DVD startup screen will appear on the screen.

About the Parental Lock screen

NO DISC

If the Parental Lock YES/NO screen appears after loading a

disc and you want to temporarily unlock the Parental Lock,

select “YES” and then input the PIN CODE following the on-

screen menu. (The Parental Lock YES/NO screen may be

repeated two times depending on the disc.)

Welcome

Load the disc in the disc slot with the label side facing

forward. (If the disc has a label.) Hold the disc without

touching either of its surfaces, align it with the guides, and

place it in position.

THE PARENTAL LEVEL OF THE

PLAYER HAS BEEN SET.

PRESS "YES" TO CONTINUE.

YES

STOP

Note:

• Some unlocked discs may not resume playback after the

input source has been changed.

• If you stop and restart playback, a message may appear on

the screen. In this case, please eject the disc and reload it.

• If you are unable to proceed from the Parental Lock screen,

please eject the disc and reload it.

Note: When inserting a disc into the DVD disc slot, do not

jam or force it strongly, otherwise the TV may malfunction

or the disc might be damaged. If left with half the disc

inserted, the disc will be loaded automatically.

CAUTION

“READING” appears on the screen, then playback starts.

Never insert your finger into the disc hole when loading a

disc into the disc slot.

READING

Keep your fingers well clear of the disc slot when a disc is

loading or unloading. Neglecting to do so may cause

personal injury.

Welcome

Because of problems and errors that can occur during the

creation of DVD and CD software and/or the manufacture

of DVD and CD discs, Toshiba cannot assure that the DVD

player contained in this television will successfully play

every disc bearing the DVD and CD logos. If you happen to

experience any difficulty playing a DVD and/or CD disc on

the DVD player contained in this television, please contact

Toshiba Customer Service.

• A menu screen will appear on the TV screen, if the disc

has a title menu. Press BbCcto select title, then press

T. Title is selected and play commences.

Press z Z to adjust the volume.

Volume

Note: When using an amplifier, adjust the volume with the

amplifier.

Press D to end playback.

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

Note:

Note: You cannot adjust the following items while a DVD is

playing:

• If a non-compatible disc is loaded, “DISK REGION

INCORRECT” will appear on the TV screen. In this case,

check your disc again (- page 7).

• Optical Output Format (- page 49)

• Audio Language (- page 48)

• DVD Audio (- page 65)

• Menu Language (- page 32)

• V-Chip (parental control) setting (- page 51)

• DVD Aspect Ratio (- page 63)

• Some discs may take a minute or so to start playback.

• If you insert a single-sided disc the wrong way, “READING”

will appear on the display for about 30-60 seconds and then

“BAD DISC” will display until you remove the disc.

• Some discs may not resume playing the same scene after

stopping.

• Some DVD playback operation may be intentionally fixed by

the software producers. Since this TV plays DVDs according

to the disc contents as designed by the software producers,

some playback features may not be available. Also refer to

the instructions supplied with the DVDs.

• Do not move the TV during playback. Doing so may damage

the disc. If you want to move the TV to another place or

room, be sure to eject the disc and turn off the power

beforehand.

If you want to adjust any of the above, stop the DVD by

pressing D twice, and then adjust (- “Resume feature”).

Note: Strong static electricity may affect the DVD player’s

operation and cause it to work improperly. If this happens, turn

OFF the POWER, disconnect and then reconnect the AC

power cord, and turn ON the TV again.

DVD VCD

About

The

DVD VCD

icons on the heading bar show the playable

• If the disc does not load when it is first inserted into the DVD

disc slot, remove the disc once and try to load the disc

again.

• Do not put any objects other than discs in the disc slot.

Doing so may cause the TV to malfunction.

discs for the function described under that heading.

DVD

: You can use this function with DVD video discs.

VCD

: You can use this function with Video CDs.

: You can use this function with Audio CDs and CD-R/

RW discs.

• When you press a button, there may be a slight delay before

the function activates.

To start playback from stop mode:

Press S.

To pause playback (still mode):

Press A during playback.

To resume normal playback, press S.

Note: The sound is muted during still mode.

To stop playback:

Press D.

To remove the disc:

Press d on the remote control or OPEN/CLOSE on the

TV. The disc will come out halfway.

Press d again to remove the disc or press S to play

again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

Using the DVD aspect ratio feature

When you view a DVD from the Built-In DVD input, you can

select the DVD aspect ratio, as described below.

• 4:3 Pan Scan: Black bars are visible on right and left sides

of the screen.

Playing in fast reverse or fast

DVD VCD CD

forward

Press H or J during playback.

H: Fast reverse playback (DVD/VCD: 2X-64X, CD/MP3:

2X-16X)

J: Fast forward playback (DVD/VCD: 2X-64X, CD/MP3:

2X-16X)

Each time you press H or J , the playback speed changes.

Picture where both sides of

the original wide screen

image are cropped.

• 4:3 Letter Box: The picture is stretched wider and taller to

fill the screen.

DVD VCD

To resume normal playback:

Press S.

Note:

• The TV mutes sound and subtitles during reverse and

forward scan of DVD video discs. However, the TV plays

sound during fast forward or fast reverse play of audio CDs.

A B C D E F G - - - - - - - - - - - - - - - -

Letter box picture

• The playback speed may differ depending on the disc.

• 16:9 Wide: The picture is stretched wider to fill the width

of the screen.

To pause playback (still playback)

DVD VCD

Press A during playback.

Squeezed picture

To select the DVD aspect ratio:

Press Y and open the Video menu.

Highlight Theater Settings and press T.

To resume normal playback:

Press S.

In the DVD Aspect Ratio field, select the mode you

prefer (4:3 Pan Scan, 4:3 Letter Box, or 16:9 Wide).

Note: The sound is muted during still playback.

Theater Settings

Picture Size

Natural

Picture Scroll

Cinema Mode

Film

Auto Aspect Ratio

DVD Aspect Ratio

16:9 Wide

Reset

Done

To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and

press T.

Note: You cannot change the DVD aspect ratio while you are

viewing a DVD. (You must be in FULL-STOP mode, not

RESUME-STOP mode.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

DVD

DVD VCD

Playing frame by frame

Changing angles

Press A during still playback.

Each time you press A, the picture advances one frame.

You can change the viewing angle of the scene during

playback if the disc is recorded with multi-angle facility.

Press a during playback.

The current angle will appear.

To resume normal playback:

Press S.

Press a repeatedly until the desired angle is selected.

Note: The sound is muted during frame by frame playback.

Note: Depending on the DVD, you may not be able to change

the angles even if multi-angles are recorded on the DVD.

DVD VCD

Playing in slow motion

DVD

Title selection

Press v or V during playback.

Each time you press the button, the slow-motion speed

changes (DVD/VCD: 1/32-1/2).

Two or more titles are recorded on some discs. If the title menu

is recorded on the disc, you can select the desired title.

Press N during playback.

Title menu appears on the screen.

Press B b C c to select the desired title.

Press T or S.

The playback of the selected title will start.

To resume normal playback:

Press S.

Note:

• Depending on the DVD, you may not be able to select the

Note:

title.

• The sound is muted during slow-motion playback.

• V is not available for the VCD disc.

• Depending on the DVD, a “title menu” may simply be called

a “menu” or “title” in the instructions supplied with the disc.

• Depending on the DVD, the title menu may be displayed

automatically when the disc is loaded.

• Depending on the DVD, a chapter menu may be displayed

after you select a title.

DVD VCD

Locating a chapter or track

Press F or G repeatedly to select the chapter or track you

want.

Playback starts from beginning of the selected chapter or track.

Note: A “Prohibition” symbol

may appear at the upper right

of the screen. This symbol means either the feature you tried is

not available on the disc, or the TV cannot access the feature

at this time. This does not indicate a problem with the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

Note:

• If the desired language is not heard after pressing the button

several times, the language is not recorded on the disc.

Changing soundtrack language

DVD VCD

• Changing soundtrack language is cancelled when you eject

the disc. The initial default language or available language

will be heard if the disc is played back again.

You can select the language when you play a multilingual disc.

• If you select DTS in playing DTS-encoded disc, no sound

Press c during playback.

The current soundtrack language will appear.

will be heard from the TV’s speakers.

AUDIO 1 / 4 : ENG

D 5 . 1

DVD

Subtitles

When playing back a disc recorded with subtitles, you can

select the subtitle language or turn the subtitle off.

Press c repeatedly until the desired language is selected.

• The on-screen display will disappear after a few

seconds.

Press b repeatedly during playback until your desired

language appears.

SUBTITLE 02 / 02 : FRE

AUDIO 2 / 4 : FRE

D 5 . 1

To turn off the subtitle, press b until “SUBTITLE OFF”

appears.

In case of Video CD playback

• The “SUBTITLE OFF” on-screen display will

disappear after a few seconds.

Stop the disc playback.

SUBTITLE OFF

Press Y and open the Audio menu.

Highlight Audio Setup and press T.

Audio

Digital Audio Selector

Note:

• Depending on the DVD, you may not be able to change

Audio Settings

subtitles, or to turn subtitles on or off.

Advanced Audio Settings

Audio Setup

• While playing a DVD, the subtitles may turn on or off when

you load or eject the disc.

• In some cases, a selected subtitle language may not be

changed immediately.

Press B or b to highlight DVD Audio, and then press C

or c to select the desired audio mode (Stereo, L-Mono,

R-Mono, or MIX-Mono).

Note: This item may not be selectable depending on the

disc.

Audio Setup

PC Audio

Auto

HDMI 1 Audio

MTS

Stereo

Language

English

Optical Output Format

Dolby Digital/Surround

Dolby Digital

Dynamic Range Control

Compressed

Stereo

DVD Audio

Reset

Done

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

DVD VCD

Disc status

MP3/JPEG CD operation

With each press of E, the status of the disc will appear on

the screen and change as follows:

This TV can play MP3/JPEG-data which has been recorded on

CD-R or CD-RW.

To produce MP3/JPEG-data, you need a Windows-PC with

CD-R/RW drive and MP3/JPEG-encoding Software (not

supplied).

Files recorded on an Apple^®HFS (hierarchical file system)

volume cannot be played.

Display example

DVD

MP3 Files

TITLE / CHAPTER

CHAPTER ELAPSED

FILE ELAPSED

Apple is a registered trademark of Apple Computer, Inc.

FILE REMAIN

OFF

CHAPTER REMAIN

TITLE ELAPSED

TITLE REMAIN

OFF

VCD

MP3/JPEG CD information

Limitations on MP3/JPEG CD playback

• MP3/JPEG CDs must meet ISO9660 standards. Files must

have one of the following extensions: .mp3, or .jpg.

• MP3/JPEG CDs cannot be used for the purpose of

recording.

• If the CD has both audio tracks and MP3/JPEG files, only

audio tracks are played.

TRACK **/**

TRACK ELAPSED

VCD

TRACK REMAIN

DISC ELAPSED

DISC REMAIN

OFF

TRACK **/**

TRACK ELAPSED

TRACK REMAIN

OFF

• It may take more than 1 minute for this TV to read MP3/

JPEG files depending on its structure.

Note:

• Some MP3/JPEG CDs cannot be played back depending on

the recording conditions.

• The CD-R/RWs that has no music data or non MP3/JPEG

files cannot be played back.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

Note:

MP3 CD playback

• The DIGITAL AUDIO OUT terminal on the TV outputs MP3

sounds in the linear PCM format regardless of the current

“Optical Output Format” selection.

Load a disc on which MP3 files have been recorded in the

disc slot.

• The DVD player contained in this television requires discs/

recordings to meet certain technical standards in order to

achieve optimal playback quality. There are many different

types of recordable disc formats (including CD-R containing

MP3/WMA files). Not all recordable discs will operate or

produce optimal playback quality. The technical criteria set

forth in this owner's manual are meant only as a guide. Use

of CD-RW for MP3 files is not recommended.

A file menu screen will appear on the screen. Press B or

b to select a folder and then press T to open the folder.

F i l e E l a p s e d 0 0 : 0 0 : 0 0

CD-ROM

ROOT

100TOSHIBA

101TOSHIBA

• You must obtain any required permission from copyright

owners to download or use copyrighted content. Toshiba

cannot and does not grant such permission.

About the menu icons

Press BbC c to highlight the desired file. The selected

file is highlighted in blue.

•

: Indicates MP3 file

•

: Indicates JPEG file

Note: To return to the previous menu, press {.

Note:

F i l e E l a p s e d 0 0 : 0 0 : 0 0

• The slide show will start automatically when the FUJICOLOR

CD or the Kodak Picture CD is played. Pressing D displays

thumbnail view.

However, depending on the recording conditions, those

discs may not operate properly.

• MP3 files on the Kodak Picture CD are not recognized on

this TV.

CD-ROM

ROOT/100TOSHIBA

001 TDCFILE....

002 TDCFILE

003 TDCFILE

004 TDCFILE

005 TDCFILE

006 TDCFILE

007 TDCFILE

ROOT

001 TDCFILE....

• When displaying the MP3/JPEG files, use the Natural or Full

picture size (- page 42).

Press S (the file is highlighted in yellow).

F i l e E l a p s e d 0 0 : 0 1 : 3 8

CD-ROM

ROOT/100TOSHIBA

001 TDCFILE....

002 TDCFILE

003 TDCFILE

004 TDCFILE

005 TDCFILE

006 TDCFILE

007 TDCFILE

ROOT

001 TDCFILE....

The selected file starts playing back.

To advance to the next MP3 file, press G.

To return to the previous MP3 file, press F.

To restart the playing MP3 file, press T.

For fast reverse playback, press H.

For fast forward playback, press J.

Press D to end playback (the file is highlighted in

yellow).

• The TV records the stopped point where playback

ended. Press S to resume playback (from the same

point).

• If you press D again (the file is highlighted in blue) or

unload the disc, the TV will clear the stopped point.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8: DVD Playback

JPEG CD playback

You can select your desired JPEG file from the file menu. The

slide show enables you to view pictures (files) one after

another automatically.

Load a disc on which JPEG files have been recorded in the

disc slot.

A file menu screen will appear. Press B or b to select a

folder and then press T to open the folder.

F i l e E l a p s e d 0 0 : 0 0 : 0 0

CD-ROM

ROOT

100TOSHIBA

101TOSHIBA

Press BbC c to select the desired file.

F i l e E l a p s e d 0 0 : 0 0 : 0 0

CD-ROM

ROOT/101TOSHIBA

001 TDCFILE....

002 TDCFILE

003 TDCFILE

004 TDCFILE

005 TDCFILE

006 TDCFILE

007 TDCFILE

Press S to start the slide show from the selected file.

If you playback the selected file only, press T. While the

picture is on-screen, you can rotate the picture by 90°

using BbC c buttons.

Press D to end playback. The file menu will appear on

the screen. If you want to view another file, repeat

steps 3–4.

• If you press A during the slide show, the slide

show stops temporarily. “PAUSE” appears on the

screen. Press S again to resume the slide show.

• To display the next file, press G.

• To display the previous file, press F.

• When slide show playback has finished, the file list

appears.

• To stop the slide show, press D. The file list will

appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 9: Troubleshooting

Cannot view external signals or channel 3 or 4

General troubleshooting

• If you cannot view signals from external devices

connected to VIDEO 1, VIDEO 2, ColorStream^®,

HDMI 1, HDMI 2, PC or from channels 3 or 4, make sure

the Input Lock is set to Off (- page 53).

Before calling a service technician, please check this chapter

for a possible cause of the problem and some solutions you can

try.

Poor color or no color

• The station may have broadcast difficulties. Try another

channel.

Black box on-screen

• Adjust the Tint and/or Color (- page 45).

• The closed caption feature is set to one of the Text modes

(T1, T2, T3, or T4). Set the closed caption feature to Off

(- page 46).

Poor composite or S-video picture

• If the TV is connected to an external A/V device (e.g.,

DVD player, video game system, set-top box, etc.) try

using a ColorStream or HDMI video connection

instead.

TV stops responding to controls

• If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn off the

TV, press and hold the POWER button on the TV control

panel for 5 or more seconds to reset the TV.

Picture and sound are out of sync

• As with all products that contain a digital display, in rare

instances, when viewing certain content (e.g.. television

broadcasts, video games, DVDs), you may notice that the

sound and picture are slightly out of sync. This

phenomenon can be caused by various factors including,

without limitation, video processing within the TV, video

processing in an attached gaming system, and video

processing or different compression rates used by

broadcasters in their programming. You may want to try

one or more of the following suggestions, which may

help to reduce the effect of this phenomenon:

Other problems

• If your TV’s problem is not addressed in this

Troubleshooting section or the recommended solution

has not worked, use the Restore Factory Defaults

procedure (- page 37).

TV will not turn on

• Make sure the power cord is plugged in, and then press

• The remote control batteries may be dead. Replace the

batteries or try the control panel buttons.

– If the TV is connected to an A/V receiver that has a

programmable audio delay feature, use this feature to

help synchronize the sound to the picture.

– If you notice this phenomenon only on certain TV

channels, please contact your local broadcast, cable, or

satellite provider to inform them of this issue.

Picture problems

General picture problems

• Check the antenna/cable connections (- Chapter 2).

• Press + on the remote control or TV and select a valid

video input source (- page 38). If no device is

connected to a particular input on the TV, no picture will

display when you select that particular input source. For

device connection details, see Chapter 2.

• Antenna reception may be poor. Use a highly directional

outdoor antenna (if applicable).

• The station may have broadcast difficulties. Try another

channel.

• Adjust the picture qualities (- page 45).

• If you are using a VCR, make sure l on the remote

control is set correctly (- page 25).

LED indications while in reboot from standby

• When you plug the power cord in, the yellow LED will

blink until the TV enters standby mode, (plugged in but

not powered on). This is normal and is not a sign of

malfunction.

Sound problems

• Check the antenna/cable connections (- Chapter 2).

• The station may have broadcast difficulties. Try another

channel.

• The sound may be muted. Press VOLUME.

• If you hear no sound, try setting the MTS feature to

Stereo mode (- page 48).

• If you are not receiving a second audio program from a

known SAP source, make sure the MTS feature is set to

SAP mode (- page 48).

• Do not connect both a standard video cable and an

S-video cable to the VIDEO 1 input at the same time

(- page 17).

Noisy picture

• If you hear audio that seems “incorrect” for the program

you are watching (such as music or a foreign language),

the SAP mode may be on. Set the MTS feature to Stereo

mode (- page 48).

• If you are watching an analog channel (off-air broadcast

or Cable TV), you can set the CableClear^®/DNR

feature to AUTO to reduce visible interference in the TV

picture (- page 58).

Video Input Selection problems

Remote control problems

• If the Input Selection window does not appear when

you press + on the remote control or TV, press + a

second time, which will change to the next video input

source and display the Input Selection window.

• Make sure the remote control is set to the correct device

mode (- page 24).

• Remove all obstructions between the remote control and

the TV.

• The remote control batteries may be dead. Replace the

batteries (- page 23).

(continued)

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 9: Troubleshooting

• Your TV remote control may not operate certain features

on your external device. Refer to the owner’s manual for

your other device to determine its available features. If

your TV remote control does not operate a specific

feature on another device, use the remote control that

came with the device (- pages 25–29).

• If the TV still does not act as expected, use the Reset

Factory Defaults procedure (- page 37).

DVD Troubleshooting

Playback doesn’t start

• The disc is reversed. Load the disc with the playback side

facing backward.

• No disc is loaded. Load the playable disc.

• The disc may be dirty. Clean the disc.

• The TV cannot play CD-ROMs, etc. Load a playable

disc.

Channel tuning problems

• Make sure the remote control is set to the correct device

mode (- page 24).

• The channel may have been erased from the channel

memory by the Channel Add/Delete feature. Add the

channel to the channel memory (- page 33).

• The channel may be blocked by the Channels Block

feature. Unblock the channel (- page 52).

• If you are unable to tune digital channels, check the

antenna configuration (- page 32). If you are still

unable to tune digital channels, clear all channels from

the channel list (- page 34) and reprogram channels

into the channel memory (- page 33). If you are still

unable to tune digital channels, use the Reset Factory

Defaults procedure (- page 37). Also see “TV stops

responding to controls” and “Other problems”

(- page 69).

No picture

• TV selector is not set correctly.

No sound

• The analog audio output terminals on the TV do not

output the sounds from the disc. Connect your digital

audio system to the DIGITAL AUDIO OUT terminal on

the TV.

• Make sure the input selector of the amplifier is set

properly.

• The TV is in the special playback mode.

Picture is distorted during fast reverse/forward playback

• The picture will be distorted occasionally.

Stopping playback, search, slow-motion play, or

changing angles, etc. cannot be performed

• Some discs may not perform certain functions.

Closed caption problems

No surround sound

• If the program or video you selected is not closed-

captioned, no captions will display (- page 46).

• If text is not available, a black rectangle may appear.

If this happens, turn off the closed caption feature (-

page 46).

• A closed-caption signal may not display correctly in the

following situations: a) when a videotape has been

dubbed; b) when the signal reception is weak; or c) when

the signal reception is nonstandard (- page 46).

• The setup may not match your stereo system.

The TV or remote operation key is not functioning

• Turn off the TV and unplug the AC power cord for

several minutes, then replug it.

Audio soundtrack and/or subtitle language is not

changed when you play back a DVD

• Multilingual language is not recorded on the DVD disc.

No subtitle

• Some discs have no subtitles.

• Subtitles are cleared. Press b.

Rating blocking (V-Chip) problems

• If you forget your PIN code: While the PIN code entering

screen is displayed, press E four times within 5

seconds. The PIN code you previously stored will be

cleared (- page 50).

• The V-Chip feature is available for the U.S. V-Chip

system only (- page 51).

Angle cannot be changed

• Multi-angles are not recorded on the DVD discs.

appears on the screen

• The function is prohibited with the TV or the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 9: Troubleshooting

LED indications

The green and yellow LED lights on the TV front indicate the TV’s status, as described below.

Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow

LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.

TV front

DISC

POWER

Yellow LED Green LED

LED Indication

Condition

Solution

1) Green is ON (solid).

2) Yellow is ON (solid).

The TV is operating properly.

A disc is in the disc slot.

TV is powering up.

–

3) Yellow blinks three

times.

Wait several seconds until the yellow LED stops

blinking.

4) Green blinks slowly.

Abnormal operation of BUS line.

Power protect detection.

Turn OFF the TV and unplug the power cord.

Plug the power cord in again and turn ON the TV.

5) Green blinks

quickly.

If, after trying the solutions, the problem still exists:

• In the U.S., call TACP Consumer Solutions at 1-800-575-5469.

• In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click

“Home Entertainment,” and then click “Support.”

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 10: Appendix

HDMI™ INPUT:

HDMI compliant (type A connector)

Specifications

HDCP compliant

Audio Lip Sync supported

Suggested formats: See table below.

HDMI Audio: 2-channel L-PCM; 32/44.1/48 kHz

sampling frequency; 16/20/24 bits per sample

Note:

• This model complies with the specifications listed

below.

• Designs and specifications are subject to change

without notice.

FIXED AUDIO OUTPUT:

150 mv (rms) (30% modulation equivalent, 2.2 k ohm

or less)

• This model may not be compatible with features and/or

specifications that may be added in the future.

DIGITAL AUDIO OUTPUT:

Television System

Optical type

NTSC standard

PC INPUT:

ATSC standard (8VSB)

Digital Cable (64 QAM, 256 QAM; in-the-clear,

unencrypted)

15-Pin D-sub Analog RGB

DVD/CD Player

DVD signal system NTSC

DVD region number 1

Applicable disc 1. DVD (12cm, 8cm [with Disc adapter])

2. CD (12cm, 8cm [with Disc adapter])

Channel Coverage

VHF: 2 through 13

UHF: 14 through 69

Cable TV: Mid band (A-8 through A-1, A through I)

Super band (J through W)

Pickup

1-Lens, 2-Beams system

Hyper band (AA through ZZ, AAA, BBB)

Ultra band (65 through 94, 100 through 135)

Dimensions

Width: 26-1/4 inches (666 mm)

Height: 20-1/4 inches (515 mm)

Depth: 9-1/2 inches (241 mm)

Power Source: 120 V AC, 60 Hz

Power Consumption

Mass (weight)

xxx W (average)

xxx W in standby mode

xxx lbs (xxx kg)

Audio Power: 10 W + 10 W

Operating conditions

Speaker Type: Two 2-3/8 × 4-3/4 inches (6 × 12 cm)

Video/Audio Terminals

Temperature: 32ºF - 95ºF (0ºC - 35ºC)

Humidity: 20 - 80% (no moisture condensation)

Supplied Accessories

S-VIDEO INPUT:

Y: 1 V(p-p), 75 ohm, negative sync.

C: 0.286 V(p-p) (burst signal), 75 ohm

• Remote control with two size “AAA” batteries

• Owner’s manual (this book)

VIDEO/AUDIO INPUT:

• Lead clip

VIDEO: 1 V(p-p), 75 ohm, negative sync.

AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k

ohm or greater)

Use this clip to attach the TV to a wall, pillar, or other

immovable structure. See item 20 on page 3.

ColorStream^®(component video) HD INPUT:

VIDEO:Y: 1V(p-p), 75 ohm

P^R: 0.7 V(p-p), 75 ohm

P^B: 0.7 V(p-p), 75 ohm

Suggested formats: 1080i, 720p, 480p, 480i

AUDIO: 150 mV(rms), 22 k ohm or greater

HDMI input supports the following signal formats:

Format

VGA

480i

Resolution

640 × 480p

720 × 480i

V. Frequency

59.940/60Hz

23.976/24Hz

59.940/60Hz

H. Frequency

Pixel Clock Frequency

25.175/25.200MHz

27.000/27.027MHz

74.176/74.250MHz

148.352/148.500MHz

31.469/31.500kHz

15.734/15.750kHz

31.469/31.500kHz

44.955/45.000kHz

33.716/33.750kHz

26.973/27.000kHz

67.433/67.500kHz

480p

720 × 480p

1280 × 720p

1920 × 1080i

1920 × 1080p

720p

1080i

1080p

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 10: Appendix

not covered by this warranty. Reception problems caused by

inadequate antenna systems, misaligned satellite dishes, cable

television distribution, VCRs, DVD players/recorders, personal

computer level IEEE-1394 devices, and any other connected signal

source device are your responsibility.

Limited United States Warranty

for LCD TV/DVD Combinations 26” and Larger

(5) Warranties extend only to defects in materials or workmanship as

limited above, and do not extend to any LCD TV/DVD Combination or

parts that have been lost or discarded by you or to damage to the

LCD TV/DVD Combination or parts caused by fires, misuse, accident,

Acts of God (such as lightning or fluctuations in electric power),

improper installation, improper maintenance, or use in violation of

instructions furnished by TACP; use or malfunction through

simultaneous use of this LCD TV/DVD Combination and connected

equipment; or to units that have been modified or had the serial

number removed, altered, defaced, or rendered illegible.

Toshiba America Consumer Products, L.L.C. (“TACP”) makes the

following limited warranties to original consumers in the United States.

THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL

CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD

TV/DVD COMBINATION AS A GIFT FROM THE ORIGINAL CONSUMER

PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.

LCD TV/DVD COMBINATIONS PURCHASED IN THE U.S.A. AND USED

ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT

LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE

WARRANTIES.

LCD TV/DVD COMBINATIONS PURCHASED ANYWHERE OUTSIDE

OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND

MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE

WARRANTIES.

How to Obtain Warranty Service

If, after following all of the operating instructions in this manual and

reviewing the section entitled “Troubleshooting,” you find that service is

needed:

(1) To find the nearest TACP Authorized Service Station, visit TACP’s

website at www.tacp.toshiba.com/service or contact TACP’s

Consumer Solution Center toll free at 1-800-575-5469.

(2) You must present your original bill of sale or other proof of purchase

to the TACP Authorized Service Station.

Limited One (1) Year Warranty on Parts and Labor

TACP warrants this LCD TV/DVD Combination and its parts against

defects in materials or workmanship for a period of one (1) year after the

date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT

TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A

NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR

PARTS OR LABOR. During this period, TACP Authorized Service Station

personnel will come to your home when warranty service is required.

Depending on the type of repair required, the service will either be

performed in your home or the LCD TV/DVD Combination will be taken to

a TACP Authorized Service Station for repair and returned to your home at

no cost to you.

For additional information, visit TACP’s website:

www.tacp.toshiba.com

ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE

U.S.A., INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED

WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY

WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.

AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,

AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH

RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO

EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST

PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR

ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR

INABILITY TO USE THIS LCD TV/DVD COMBINATION).

Rental Units

The warranty for LCD TV/DVD Combination rental units begins on the date

of the first rental or thirty (30) days after the date of shipment to the rental

firm, whichever comes first.

Limited Warranty for Commercial Units

TACP warrants LCD TV/DVD Combinations that are sold and used for

commercial purposes as follows: all parts are warranted against defects

in materials or workmanship for a period of ninety (90) days after the date

of original retail purchase. DURING THIS PERIOD, TACP WILL, AT

TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A

NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU.

No person, agent, distributor, dealer, or company is authorized to change,

modify, or extend the terms of these warranties in any manner whatsoever.

The time within which an action must be commenced to enforce any

obligation of TACP arising under the warranty or under any statute or law

of the United States or any state thereof is hereby limited to ninety (90)

days from the date you discover, or should have discovered, the defect.

This limitation does not apply to implied warranties arising under the law

of any state of the U.S.A.

Owner’s Manual and Product Registration Card

Read this owner’s manual thoroughly before operating this LCD TV/DVD

Combination.

Complete and mail the enclosed product registration card or register your

LCD TV/DVD Combination online at www.tacp.toshiba.com/service

as soon as possible. By registering your LCD TV/DVD Combination you

will enable TACP to bring you new products specifically designed to meet

your needs and help us to contact you in the unlikely event a safety

notification is required under the U.S. Consumer Product Safety Act.

Failure to complete and return the product registration card

does not diminish your warranty rights.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU

MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE

TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT

ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED

WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY

TO YOU UNDER SUCH CIRCUMSTANCES.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING

CONDITIONS:

(1) You must retain your original bill of sale or provide other proof of

purchase.

(2) All warranty servicing of this LCD TV/DVD Combination must be

performed by an Authorized TACP Service Station.

(3) The warranties from TACP are effective only if this LCD TV/DVD

Combination is purchased and operated in the Continental U.S.A. or

Puerto Rico.

(4) Labor service charges for set installation, setup, adjustment of

customer controls, and installation or repair of antenna systems are

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 10: Appendix

(d) FOR TELEVISIONS OVER 32 INCHES: During this period, ASP

personnel will come on-site when warranty service is required.

Depending on the type of repair required, the service will either be

performed on-site or the Television will be taken to an ASP for repair

and returned at no cost to you. ON-SITE SERVICE ONLY APPLIES

WITHIN 100 KILOMETERS OF AN ASP. IF YOU ARE NOT WITHIN

100 KILOMETERS OF AN ASP, YOU MUST DELIVER THE ENTIRE

TELEVISION TO AN ASP. YOU MUST PAY FOR ALL

Limited Canadian Warranty

for Toshiba Brand Flat Panel Televisions

Toshiba of Canada Limited (“TCL”) makes the following limited warranties

to original consumers in Canada. THESE LIMITED WARRANTIES

EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY

PERSON RECEIVING THIS TOSHIBA BRAND FLAT PANEL

TELEVISION (the “TELEVISION(S)” or “Television(s)”) AS A GIFT FROM

THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER

PURCHASER OR TRANSFEREE.

TRANSPORTATION AND INSURANCE CHARGES FOR THE

TELEVISION TO AND FROM THE ASP.

Rental Units

The warranty for Television rental units begins with the date of first rental

or thirty (30) days from the date of shipment to the rental firm, whichever

comes first.

TELEVISIONS PURCHASED IN CANADA, AND USED ANYWHERE

OUTSIDE OF CANADA INCLUDING, WITHOUT LIMITATION, THE

UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE

WARRANTIES.

Your Responsibility

THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING

CONDITIONS:

TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF CANADA,

INCLUDING, WITHOUT LIMITATION, THE UNITED STATES AND

MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE

WARRANTIES.

(1) You must provide your bill of sale or other proof of purchase.

(2) All warranty servicing of this Television must be performed by an ASP.

(3) The warranties from TCL are effective only if the Television is (i)

purchased as new and unopened from TCL or from TCL’s authorized

distributors, dealers or resellers (“ADR’s”) and (ii) located/operated in

Canada.

(4) Labour charges for set installation, setup, adjustment of customer

controls, and installation or repair of antenna systems are not covered

by these warranties. Reception problems caused by inadequate

antenna systems are your responsibility.

(5) Warranties extend only to material defects in materials or

workmanship as limited above, and do not extend to:

a. Service, repairs or replacement made necessary by accident,

misuse, abuse, moisture, liquids, dust, dirt, neglect, accident,

damage, 24/7 applications, improper installation, improper

operation, improper cleaning, improper maintenance, normal

wear and tear, screen burn or image retention caused by

prolonged display of static images and/or phosphor aging, or any

other external cause or event, act or omission outside the control

of TCL, including fire, theft, acts of God, alteration, power failures,

power surges or power shortages, lightning, other electrical

faults, or repairs, modifications or replacements by persons other

than those authorized by TCL to service the Television;

b. Replacement of missing, discarded or lost parts, the provision of

retrofits, or preventive maintenance;

Limited One (1) Year Warranty on Parts and Labour

Subject to the more limited warranty if the Television is used for any

commercial or business purposes as set out below, TCL warrants the

Television and its parts against material defects in materials or

workmanship that result in the Television failing for a period of one (1) year

after the date of original retail purchase. DURING THIS PERIOD, TCL

WILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART

WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU

FOR PARTS OR LABOUR.

(a) FOR TELEVISIONS 32 INCHES OR LESS: YOU MUST DELIVER THE

ENTIRE TELEVISION TO A TCL TELEVISION AUTHORIZED

SERVICE PROVIDER (“ASP”). YOU MUST PAY FOR ALL

TRANSPORTATION AND INSURANCE CHARGES FOR THE

TELEVISION TO AND FROM THE ASP.

(b) FOR TELEVISIONS OVER 32 INCHES: During this period, ASP

personnel will come to your home when warranty service is required.

Depending on the type of repair required, the service will either be

performed in your home or the Television will be taken to an ASP for

repair and returned to your home at no cost to you. IN-HOME

SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF AN ASP.

IF YOU ARE NOT WITHIN 100 KILOMETERS OF AN ASP, YOU

MUST DELIVER THE ENTIRE TELEVISION TO AN ASP. YOU MUST

PAY FOR ALL TRANSPORTATION AND INSURANCE CHARGES

FOR THE TELEVISION TO AND FROM THE ASP.

c. Repair of damage that is cosmetic only or does not affect the

Television functionality, such as wear and tear, scratches and

dents;

d. Service on Toshiba-branded accessory items (such accessory

items may be covered by their own warranty);

e. Service on third party products or service made necessary by

use of incompatible third party products;

f. Service made necessary by the simultaneous use of this

Television and connected equipment;

g. Modifications to the Television not approved in writing by TCL,

and service made necessary by the use or installation of non-

Toshiba modifications to the Television;

Limited Warranty for Commercial Units

TCL warrants Televisions that are used for any commercial or business

purposes as follows: all parts are warranted against material defects in

materials or workmanship that result in the Television failing for a period of

ninety (90) days after the date of original retail purchase. DURING THIS

PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE THE

DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT

CHARGE TO YOU.

ENTIRE TELEVISION TO AN ASP. YOU MUST PAY FOR ALL

TRANSPORTATION AND INSURANCE CHARGES FOR THE

TELEVISION TO AND FROM THE ASP.

h. Service of a Television on which the TOSHIBA label or logo, rating

label or serial number have been defaced or removed;

i. On-site service and repair of the Television; and

j. Damage to the Television caused by failure to follow the

specifications, User manuals or guides as to usage and/or

storage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 10: Appendix

Disclaimer and Limitation of Remedy

agree to opt out of any such representative or class proceedings.

Arbitration of any Dispute will be conducted in the forum and in the

manner as agreed to between you and TCL. Failing such agreement, the

arbitration will be conducted by one arbitrator pursuant to the laws and

rules relating to arbitration generally in force in the jurisdiction in which you

reside at the time that the Dispute arises. To the extent not precluded by

law, no claim, dispute, controversy or disagreement of any other person

may be joined or combined with any Dispute by you, without the prior

written consent of TCL.

TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER EXPRESS

AND IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS

FOR THIS TELEVISION, INCLUDING THE IMPLIED WARRANTIES,

CONDITIONS AND REPRESENTATIONS OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED

AND EXCLUDED. IF THE APPLICABLE LAW, STATUTORY OR

OTHERWISE, PRECLUDES THE EXCLUSION OF ANY IMPLIED

WARRANTIES, CONDITIONS AND REPRESENTATIONS THEN SUCH

IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS ARE

OTHERWISE LIMITED IN DURATION TO THE TERM OF THIS

EXPRESS WRITTEN LIMITED WARRANTY. TO THE EXTENT NOT

PRECLUDED BY LAW, STATUTORY OR OTHERWISE, THIS WRITTEN

WARRANTY SUPERCEDES AND SPECIFICALLY DISCLAIMS ANY

OTHER WARRANTY, CONDITION OR REPRESENTATION NOT

STATED IN THIS WARRANTY, WHETHER MADE BY TCL, TOSHIBA

CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND WHETHER

MADE ORALLY OR IN WRITING (INCLUDING ANY STATEMENT IN

ANY BROCHURE, PRESS RELEASE, ANNOUNCEMENT,

Critical Applications

The Television you have purchased is not designed for any “critical

applications.” “Critical applications” means life support systems, medical

applications, connections to implanted medical devices, commercial

transportation, nuclear facilities or systems or any other applications

where Television failure could lead to injury to persons or loss of life or

catastrophic property damage.

IF THE CUSTOMER USES THE TELEVISION IN ANY CRITICAL

APPLICATION, THE CUSTOMER - AND NOT TCL, ITS AFFILIATES, ADRs

OR ASPs - ASSUME SOLE AND FULL RESPONSIBILITY FOR SUCH USE.

TCL RESERVES THE RIGHT TO REFUSE TO SERVICE ANY TELEVISION

USED IN A CRITICAL APPLICATION. TCL, ITS AFFILIATES, ADRs AND

ASPs HEREBY DISCLAIM ANY AND ALL LIABILITY, DAMAGES AND

CONSEQUENCES ARISING OUT OF THE SERVICE OR REFUSAL TO

SERVICE SUCH TELEVISION AND FURTHER DISCLAIM ANY AND ALL

LIABILITY, CONSEQUENCES AND DAMAGES THAT MAY ARISE OR

RESULT FROM THE USE OF THE TELEVISION IN ANY CRITICAL

APPLICATIONS.

ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).

YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE

INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR

MANUALS. IF YOU FAIL TO DO SO, THIS TELEVISION MAY NOT

FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE. THIS

WARRANTY WILL NOT COVER ANY SERVICE THAT IS REQUIRED, IN

PART OR IN WHOLE, AS A RESULT OF ANY FAILURE TO FOLLOW THE

SET-UP AND USAGE INSTRUCTIONS. THIS WARRANTY DOES NOT

APPLY AND SHALL BE VOID AND UNENFORCEABLE IF THE

TELEVISION IS OPENED, SERVICED, OR REPAIRED BY PERSONS

OTHER THAN THOSE AUTHORIZED BY TCL TO SERVICE OR REPAIR

THE TELEVISION.

General Provisions

If and to the extent that any provision of this limited warranty should

generally be found to be unenforceable, the unenforceable provision shall

be severed from the warranty and deemed not to form part of the warranty.

The remaining provisions of this warranty shall be and remain valid and

enforceable. If and to the extent that any provision of this limited warranty

as it relates to any of the Related Parties is found to be invalid or

unenforceable in respect of that party (the “Excluded Party”), the

Excluded Party shall be deemed to be severed or excluded from the

provision, and the provision shall remain valid, enforceable and

applicable in respect of the other or remaining Related Parties.

IF THE TELEVISION FAILS TO WORK AS WARRANTED ABOVE, YOUR

SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT

OF THE DEFECTIVE PART. IN NO EVENT WILL TCL, TOSHIBA

CORPORATION, THEIR AFFILIATES, ADRs OR ASPs (THE “RELATED

PARTIES”) BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY

DAMAGES, MONEY, REIMBURSEMENT, COSTS OR EXPENSES. THIS

LIMITATION APPLIES TO DAMAGES, MONEY, REIMBURSEMENT,

COSTS OR EXPENSES OF ANY KIND WHATSOEVER INCLUDING ANY

DIRECT OR INDIRECT DAMAGES, DAMAGE TO PROPERTY OR

PERSON, LOST PROFITS, LOST SAVINGS, INCONVENIENCE OR

OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL

DAMAGES, WHETHER FOR BREACH OF WARRANTY, BREACH OF

CONTRACT, TORT (INCLUDING NEGLIGENCE), UNDER A STATUTE OR

UNDER ANY OTHER LAW OR FORM OR ACTION, OR WHETHER

ARISING OUT OF THE USE OF OR INABILITY TO USE THE TELEVISION,

EVEN IF ANY OF THE RELATED PARTIES HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER

PARTY.

To the extent permitted by law, this limited warranty shall be governed and

construed in accordance with the laws of Ontario.

If there is any inconsistency between this limited warranty, on the one

hand, and any statement in the packaging of the Television or in any other

document enclosed with, or used in the context of the promotion or sale

of, the Television, on the other hand, the provisions of this limited warranty

shall prevail.

How to Obtain Warranty Services

If, after following all of the operating instructions in this manual and

checking the “Troubleshooting” section, you find that service is needed:

No person, agent, distributor, dealer or company is authorized to change,

modify or extend the terms of these warranties in any manner whatsoever.

(1) To find the nearest ASP, visit TCL’s web site at www.toshiba.ca, or

call toll free 1-800-268-3404

(2) Present your bill of sale or other proof of purchase to the ASP.

Arbitration and Dispute Resolution

To the extent not precluded by law, any claim, dispute, controversy or

disagreement (whether for breach of warranty, breach of contract, tort

(including negligence), under a statute or under any other law or form of

action) against any of the Related Parties arising out of, or otherwise

relating to: (i) this warranty; (ii) the Television; (iii) any oral or written

representations, statements, brochures, press releases, advertising,

announcement, point of sale display, or promotional material relating to

the Television; (iv) the relationships that result from this warranty, (the

foregoing claims, disputes controversies and disagreements are

collectively referred to as the “Dispute”), shall be referred to and resolved

by final and binding arbitration (to the exclusion of the courts). To the

extent not precluded by law, you agree to waive any right that you may

have to commence or participate in any representative or class

proceeding against the Related Parties relating to any Dispute. If and

where applicable and to the extent not precluded by law, you further

For additional information, visit TCL’s website at www.toshiba.ca

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 10: Appendix

A copy of the GPL source code in this product may be obtained by

contacting Toshiba Consumer Solutions at (800)631-3811. There will be

a charge to cover the costs of providing the source code.

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”

AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN

IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product

includes cryptographic software written by Eric Young

A copy of the LGPL source code in this product may be obtained by

contacting Toshiba Consumer Solutions at (800)631-3811. There will be

a charge to cover the costs of providing the source code.

reserved.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

(1) Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) Neither the name of The NetBSD Foundation nor the names of its

contributors may be used to endorse or promote products derived

from this software without specified prior written permission.

THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.

AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL

THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

([email protected]). This product includes software written by Tim

Hudson ([email protected]).

reserved. This package is an SSL implementation written by Eric Young

([email protected]). The implementation was written so as to conform

with Netscapes SSL. This library is free for commercial and non-

commercial use so long as the following conditions are adhered to. The

following conditions apply to all code found in this distribution, be it the

RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL

documentation included with this distribution is covered by the same

the code are not to be removed. If this package is used in a product, Eric

Young should be given attribution as the author of the parts of the library

used. This can be in the form of a textual message at program startup

or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:

(1) Redistributions of source code must retain the copyright notice, this

list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) All advertising materials mentioning features or use of this software

must display the following acknowledgement: “This product includes

cryptographic software written by Eric Young ([email protected]).”

The word ‘cryptographic’ can be left out if the routines from the library

being used are not cryptographic related.

This product includes software developed by the OpenSSL Project for use

in the OpenSSL Toolkit (http://www.openssl.org).

This product includes cryptographic software written by Eric Young

([email protected]).

reserved. Redistribution and use in source and binary forms, with or

without modification, are permitted provided that the following conditions

are met:

(4) If you include any Windows specific code (or derivative thereof) from

the apps directory (application code) you must include an

(1) Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

(2) Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

(3) All advertising materials mentioning features or use of this software

must display the following acknowledgement: This product includes

software developed by the OpenSSL Project for use in the OpenSSL

Toolkit (http://openssl.org).

(4) The names “OpenSSL Toolkit” and “Open SSL Project” must not be

used to endorse or promote products derived from this software

without prior written permission. For written permission, please

contact [email protected].

(5) Products derived from this software may not be called “OpenSSL” nor

may “Open SSL” appear in their names without prior written

permission of the OpenSSL Project.

(6) Redistributions of any form whatsoever must retain the following

acknowledgement: “This product includes software developed by the

OpenSSL Project for use in the OpenSSL Toolkit (http://

www.openssl.org).”

acknowledgement: “This product includes software written by Tim

Hudson ([email protected]).”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE. The license and distribution terms for any publicly available

version or derivative of this code cannot be changed, i.e. this code cannot

simply be copied and put under another distribution license (including the

GNU Public License).

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

POWER button ........................ 13, 24

Antenna cable ................................ 15

Antenna input configuration ............ 32

Audio quality adjustments............... 48

Audio system connection................ 21

Auto aspect.................................... 44

Auto power off................................ 56

Features, TV ..................................11

Front of the TV ...............................13

RECALL button...............................56

Remote control

Battery installation....................23

Device code table.....................28

Effective range.........................23

Functional key chart .................26

Learning about the buttons .......24

Programming ...........................27

Game Mode feature........................59

HDMI audio mode...........................35

HDMI cable ....................................15

HDMI^™connection..........................20

Back of the TV................................ 14

Base closed captions...................... 46

Blocking channels .......................... 52

Reset Factory Defaults....................37

INFO button....................................56

INPUT button..................................38

Installation, care, and service ............3

Installation, setup............................12

Integrated digital tuning...................11

Safety...............................................2

SAP sound .....................................48

Satellite receiver connection............18

Scroll settings .................................43

Selecting Menu Language...............32

Service .............................................4

Side panel control ...........................13

Sleep timer .....................................55

Specifications .................................72

StableSound^®................................... 49

Stereo sound ..................................48

SurfLock^™........................................ 41

S-video cable..................................15

System status .................................36

Cable box connection ..................... 17

CableClear^®..................................... 58

Camcorder connection.................... 19

CH Bb buttons ........................24, 41

CH RTN button.........................24, 41

Channel Browser Setup.................. 39

Channel Browser^™........................... 39

Channel labeling ............................ 34

Channel Number buttons..........24, 41

JPEG .............................................68

Labeling video input........................38

Language selection.........................32

Last mode memory feature .............56

LED indications.........................13, 71

Channel programming

Automatic programming........... 33

Manually adding and deleting... 33

LOCKS menu

Cinema mode................................. 44

Closed captions.............................. 46

Color temperature .......................... 58

ColorStream^®................................... 18

Component video ........................... 18

Component video cables ................ 15

Connecting cables.......................... 15

Channels, blocking...................52

Enable rating blocking..............51

New PIN code..........................50

Panel lock................................54

Unlocking programs

temporarily.................53

Video inputs, locking ................53

TheaterWide^®picture size...............42

Troubleshooting ..............................69

TV status information ......................56

Locks menu....................................50

V-Chip blocking (Locks menu).........50

VCR connection................. 16, 17, 18

Video cables...................................15

Video input label .............................38

Video input lock ..............................53

Digital Audio Out ............................ 21

Digital audio selector ...................... 47

Digital CC Settings ......................... 46

Digital signal meter......................... 36

Dolby Digital................................... 21

MP3 ...............................................67

MPEG noise reduction ....................59

MTS feature ...................................48

MUTE button ..................................47

Warranty

Dolby Digital Dynamic Range

Control........................................ 49

Canada....................................74

U.S..........................................73

Optical audio cable .........................15

Optical audio output format .............49

DVD

DVD aspect ratio ..................... 63

Fast forward ............................ 63

Fast reverse ............................ 63

Frame by frame....................... 64

MP3/JPEG CD operation ......... 66

Playback ................................. 61

WOW:SRS 3D ................................60

WOW:SRS Focus ...........................60

WOW:SRS TruBass........................60

PC Audio........................................55

PC connection................................22

PC settings.....................................54

Picture adjustment..........................45

Picture mode ..................................45

Picture quality.................................45

Picture scroll...................................43

Picture size selection ......................42

DVD player connection................... 18

DVI connection............................... 20

DynaLight^™...................................... 45

Dynamic contrast............................ 57

Download from Www.Somanuals.com. All Manuals Search And Download.

Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.

NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.

HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400

SERVICE CENTERS:

TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400

MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766

VANCOUVER: 13551 COMMERCE PARKWAY, SUITE 110, RICHMOND, B.C., V6V 2L1, CANADA – TEL: (604) 303-2500

MANUFACTURED BY

CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.

Channel Browser, SurfLock, DynaLight, and LCDVD logo are trademarks of Toshiba America Consumer Products, L.L.C.

REGZA is a resistered trademark of Toshiba Corporation.

PRINTED IN USA

(07-08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Tech Craft TV Video Accessories MC6032B User Manual
Therma Stor Products Group Air Cleaner 135H User Manual
Tote Vision Security Camera MX 07WP User Manual
Tripp Lite Network Cables N201 007 BK User Manual
True Fitness Fitness Equipment TrueStretch User Manual
Uniden Automobile Electronics UBC248CLT User Manual
Uniden Headphones BTS200 User Manual
Uniden Two Way Radio UH037SX 2 User Manual
VTech Laptop XL Series User Manual
Weed Eater Lawn Mower WE165T42A User Manual