DVD VIDEO PLAYER / VIDEO CASSETTE RECORDER
SD-V296KU
Owner’s Record
The model number and serial number are on the back
of your product. Record these numbers in the spaces
below. Refer to these numbers whenever you communicate
with your Toshiba dealer about this product.
Model number:
Serial number:
© 2008 Toshiba Corporation
E8EB5UD_SD-V296KU_EN_ES_v1.indd
1
2008/07/14 10:36:07
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
This unit has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard.
The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing.
This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
19. Do not place the apparatus on amplifiers or equipment
that may produce heat.
20. Never block or cover the slots or openings in the unit.
Never place the unit:
4. Follow all instructions.
• on a bed, sofa, rug, or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, built-in cabinet,
or any other place with poor ventilation.
The slots and openings are provided to protect the unit
from overheating and to help maintain reliable operation.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
21. Do not use a cracked, deformed, or repaired disc. These
discs are easily broken and may cause serious personal
injury and apparatus malfunction.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
22. If the apparatus should emit smoke or an unusual odor,
immediately disconnect the power cord from the wall
outlet. Wait until the smoke or smell stops, then ask your
dealer for a check and repair. Neglecting to do so may
cause fire.
23. During thunderstorms, do not touch the connecting
cables or the apparatus.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
24.
DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
11. Only use attachments/accessories specified by the
manufacturer.
• Use extreme care to make sure you are never in a
position where your body (or any item you are in
contact with, such as a ladder or screwdriver) can
accidentally touch overhead power lines. Never locate
the antenna near overhead power lines or other
electrical circuits.
• Never attempt to install any of the following during
lightning activity: a) an antenna system; or b) cables,
wires, or any home theater component connected to an
antenna or phone system.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus and disconnect the antenna or
cable system during lightning storms or when unused for
long periods of time.
25. Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see Section
810 of the National Electric Code).
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
ANTENNA
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
LEAD
WIRE
15. Do not overload wall outlets; extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
16. Never expose the apparatus to dripping or splashing or
place items such as vases, aquariums, any other item
filled with liquid, or candles on top of the unit.
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
NEC – NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
17. Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
18. Do not place anything on top of this unit.
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or
climbing on it. A falling unit can cause serious injury or even death.
–
–
EN
3
E8EB5UD_SD-V296KU_EN_ES_v1.indd
3
2008/07/14 10:36:12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Location
Supplied Accessories
For safety and optimum performance of this unit:
Remote control with
two AA batteries
RCA Audio/Video cables
• Install the unit in a horizontal and stable position. Do
not place anything directly on top of the unit. Do not
place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from
devices of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper heat
dissipation. Do not block the ventilation holes on the
sides of the unit. Avoid locations subject to strong
vibration or strong magnetic fields.
Owner’s Manual
Quick Start Guide
Avoid the Hazards of Electrical Shock and Fire
Owner's Manual
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Return Stop Sheet
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it
is moved from a cold place to a warm place or after
heating a cold room or under conditions of high humidity.
Do not use this unit at least for 2 hours until its inside gets
dry.
Symbols Used in this Manual
The following symbols appear in some headings in this
manual.
About Copyright
The unauthorized recording, use, distribution, or revision
of television programs, videotapes, DVDs and other
materials, is prohibited under the copyright laws of the
United States and other countries, and may subject you to
civil and/or criminal liability.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
: Description refers to video cassette tapes.
: Description refers to playback of DVD-Video.
: Description refers to playback of Audio CDs.
: Description refers to playback of JPEG files.
Notice for Progressive Scan Output
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of picture problems with 480 progressive scan output, it
is recommended that the user switch the connection to
the “standard definition” output. If there are questions
regarding your TV set compatibility with this 480p DVD
recorder, please contact Toshiba Customer Service.
Manufactured under license under U.S. Patent #:
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc.
©1996-2007 DTS, Inc. All Rights Reserved.
Auto Power Off and Screen Saver Function (DVD Only)
If the player is left with no activity for more than 5
minutes, the screen saver will be activated, and if it is left
for another 25 minutes, the unit switches from DVD to VCR
mode automatically.
–
–
EN
4
E8EB5UD_SD-V296KU_EN_ES_v1.indd
4
2008/07/14 10:36:14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Table of Contents
PRECAUTIONS
SERVICING
Laser Safety..............................................................................................................2
IMPORTANT SAFETY INSTRUCTIONS ............................................3
Installation Location.............................................................................................4
Avoid the Hazards of Electrical Shock and Fire..........................................4
Moisture Condensation Warning.....................................................................4
About Copyright....................................................................................................4
Notice for Progressive Scan Output ...............................................................4
Auto Power Off and Screen Saver Function (DVD Only).........................4
Supplied Accessories............................................................................................4
Symbols Used in this Manual............................................................................4
Maintenance............................................................................................................5
• Please refer to relevant topics on the “Troubleshooting”
on page 27 before returning the unit.
• If this unit becomes inoperative, do not try to correct the
problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call
our help line to locate an Authorized Service Center.
CLEANING THE CABINET
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
SETUP
Choosing a Disc / Cassette Tape ...................................................6
Playable Media........................................................................................................6
Unplayable Media..................................................................................................6
Index to Parts and Controls...........................................................7
Front Panel...............................................................................................................7
Rear Panel.................................................................................................................7
Remote Control......................................................................................................8
Installing the Batteries for the Remote Control .........................................8
DVD Display Panel.................................................................................................9
VCR Display Panel..................................................................................................9
Selecting DVD or VCR Operation.....................................................................9
Connections.................................................................................10
Connection to RF Modulator (Not Supplied) ...........................................10
Connection to a TV.............................................................................................10
Connection to an Audio System...................................................................11
Connection to an External Tuner..................................................................11
Preparation for Use .....................................................................12
Turning on Unit for the First Time................................................................12
Clock Setting ........................................................................................................12
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the center to out. Do not wipe in a
circular motion.
• Do not use solvents such as benzine, thinner, commer-
cially available cleaners, detergent, abrasive cleaning
agents or antistatic spray intended for analog records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you
refer to the relevant sections and to “Troubleshooting”
in this Owner’s Manual, the laser optical pickup unit may
be dirty. Consult your dealer or an Authorized Service
Center for inspection and cleaning of the laser optical
pickup unit.
VCR FUNCTIONS
Playback ......................................................................................13
When You Playback a Cassette Tape Recorded in Hi-Fi Stereo.........13
Other Operations.........................................................................13
Index Search .........................................................................................................13
Time Search ..........................................................................................................13
Auto Repeat..........................................................................................................14
Recording.....................................................................................14
Recording & One-touch Timer Recording (OTR).....................................14
Timer Recording..................................................................................................14
Notes for Timer Recording & One-touch Timer Recording (OTR).....15
Satellite Link .........................................................................................................16
Copying a Cassette Tape .................................................................................16
DVD to Cassette Tape Duplication...............................................................17
DISC HANDLING
• When you handle a disc hold it by its edge and try not to
touch the surface of the disc.
• Always store a disc in its protective case when it is not
used.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove
a cassette tape, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accumu-
lated on the video heads after a long period of use, or
the usage of rental or worn cassette tapes can cause this
problem. If a streaky or snowy picture appears during
playback, the video heads in your unit may need to be
cleaned.
1. Please visit your local audio/video store and purchase a
good quality VHS video head cleaner.
2. If a Video head cleaner does not solve the problem,
please call our toll free customer support line found on
the cover of this manual to locate an authorized service
center.
DVD FUNCTIONS
Playback ......................................................................................17
On-Screen Display .......................................................................18
JPEG Playback .............................................................................19
Search Functions .........................................................................20
Using Track Search.............................................................................................20
Using Title / Chapter Search...........................................................................20
Using Time Search..............................................................................................20
Marker Setting .....................................................................................................20
Repeat / Random / Programmed Playback ................................21
Repeat Playback..................................................................................................21
Repeat A-B Playback..........................................................................................21
Random Playback...............................................................................................21
Programmed Playback......................................................................................21
Special Settings ...........................................................................22
Subtitle Language..............................................................................................22
Audio Language..................................................................................................22
Camera Angles.....................................................................................................22
Black Level Setting .............................................................................................22
Stereo Sound Mode...........................................................................................22
Virtual Surround..................................................................................................22
DVD Setting .................................................................................23
LANGUAGE Setting ............................................................................................23
DISPLAY Setting ..................................................................................................24
AUDIO Setting......................................................................................................24
PARENTAL Setting..............................................................................................25
OTHERS Setting ...................................................................................................26
Reset to the Default Setting (Except for PARENTAL Setting).............26
Note:
• Remember to read the instructions along with the video head cleaner
before use.
• Clean video heads only when problems occur.
Note to CATV system installer:
• This reminder is provided to call the cable TV system installer’s attention
to Article 820-40 of the National Electrical Code, which provides
guidelines for proper grounding - in particular, specifying that the cable
ground shall be connected to the grounding system of the building, as
close to the point of cable entry as possible.
INFORMATION
Troubleshooting..........................................................................27
Specifications ..............................................................................28
Language Code List .....................................................................28
LIMITED WARRANTY....................................................................29
Español ........................................................................................32
–
–
EN
5
E8EB5UD_SD-V296KU_EN_ES_v1.indd
5
2008/07/14 10:36:17
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Choosing a Disc / Cassette Tape
Playable Media
Type of
media
Recorded
signals
Mark (logo)
Region code
Media size
Tape speed and disc types
tape width
1/2 inches
(12.65mm)
cassette
tape
SP: 1-5/16 inch/sec. (33.40 mm/sec.)
SLP: 7/16 inch/sec. (11.12 mm/sec.)
analog video
DVD-video
*1, 2, 3, 5, 8
or
5 inches
(12 cm)
or
3 inches
(8 cm)
DVD-RW
DVD-R
*1, 3, 4, 5, 6,
7, 8, 9
e.g.)
title 1
title 2
digital video
(MPEG2)
chapter 1 chapter 2 chapter 3 chapter 4 chapter 1
chapter 2
DVD+RW
DVD+R
*1, 3, 4, 5, 7, 8
Audio CD
*3, 5, 8
audio CD
JPEG
e.g.)
track 1
track 2
track 3
track 4
track 5
track 6
5 inches
(12 cm)
or
3 inches
(8 cm)
digital audio
or
JPEG
CD-RW
CD-R
e.g.)
folder 1
folder 2
*3, 4, 5, 7, 8
file 1
file 2
file 3
file 4
file 5
file 6
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.
*2: Certain DVD-video does not operate as described in this manual due to the intentions of the disc’s producers.
*3: Scratched or stained discs may not be played back.
*4: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or special prop-
erties of discs.
*5: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not play them back. Even if
they are played back, the sound or video quality will be compromised.
*6: You may play back the unfinalized DVD-RW/-R recorded in the video format on our brand’s DVD recorder. However, depending
on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth,
etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.
*7: If the recorded portion of the disc is too small (less than 2-3/16 inches (55 mm) across), it may not play back properly.
*8: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
*9: Discs recorded in the VR (video recording) format cannot be played back.
• Because of problems and errors that can occur during the creation of DVD and CD software and/or the manufacture of DVD and CD
discs, Toshiba cannot assure that this DVD player will successfully play every disc bearing the DVD and CD logos. If you happen to
experience any difficulty playing a DVD and/or CD disc on this DVD player, please contact Toshiba Customer Service.
Unplayable Media
NEVER play the following discs as malfunction may result!
DVD-RAM, DVD-audio, CD-i, photo CD, DVD with region codes other than 1 or ALL, DVD-ROM for personal computers, CD-ROM for
personal computers, DVD-RW/-R in VR mode, DVD or CD with MP3/WMA files, HD DVD, Blu-ray Disc
On the following disc, the sound MAY NOT be heard.
super audio CD
Note:
• Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density super audio CD layer cannot be delivered.
Any other discs without compatibility indications
–
–
EN
6
E8EB5UD_SD-V296KU_EN_ES_v1.indd
6
2008/07/14 10:36:20
Download from Www.Somanuals.com. All Manuals Search And Download.
Index to Parts and Controls
Front Panel
1
2
3 4 5 6 7
8
9*
10
21 20
19 18 17
16
15
14 13 12 11*
( ) The unit can also be turned on by pressing these buttons or by
11. B (PLAY) button (DVD only)*
Press to start or resume playback.
12. C (STOP) button (DVD only)
Press to stop playback or recording.
Press to stop the proceeding timer recording in DVD.
13. VCR/DVD button
Press to select the component you wish to operate.
14. VCR/DVD indicator
*
inserting a cassette tape.
1. I/y ON/STANDBY button
Press to turn on and off the unit.
2. POWER ON indicator
This indicator will light up when the power is on and turn off
when the power is off.
3. E (REW) button (VCR only)
Press to rewind the cassette tape, or to view the picture
rapidly in reverse during playback (rewind search).
4. D (FWD) button (VCR only)
Lights up when the VCR/DVD output mode is selected.
15. TRACKING
/
buttons (VCR only)
Press to adjust the tracking during playback or in slow motion
of the cassette tape.
Press to rapidly advance the cassette tape, or to view the
picture rapidly in forward during playback (forward search).
5. C / A (STOP/EJECT) button (VCR only)
C (STOP) button
Press to stop cassette tape playback or recording.
Press to stop the proceeding timer recording in VCR.
A (EJECT) button
When the unit is in stop mode, press to remove the cassette
tape from the cassette compartment.
6. B (PLAY) button (VCR only)
Press to start playback.
7. I REC button (VCR only)
Press once to start a recording. Press repeatedly to start the
one-touch timer recording.
8. Cassette compartment (VCR only)
Insert a cassette tape here.
While playback is in still mode, you can stabilize the picture.
16. Display
Refer to “DVD Display Panel” and “VCR Display Panel” on page 9.
17. Remote control sensor
Receive signals from your remote control so that you can
control the unit from a distance.
18. TIMER REC indicator (VCR only)
Lights up when a timer recording or OTR (One-touch Timer
Recording) has been set.
Blinks when a timer recording or OTR (One-touch Timer
Recording) has been finished or if the unit could not
complete the recording due to some error.
19. REC indicator (VCR only)
Lights up during a recording, OTR (One-touch Timer
Recording) or timer recording.
Blinks when a recording is paused.
9. A OPEN/CLOSE button (DVD only)*
Press to open or close the disc tray.
10. Disc tray (DVD only)
20. AUDIO input jacks (L2) (VCR only)
Use to connect external device with an RCA audio cable.
21. VIDEO input jack (L2) (VCR only)
Place a disc when it is open.
Use to connect external device with an RCA video cable.
Rear Panel
DVD
DVD/VCR VCR
AUDIO OUT AUDIO IN
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
OUT
OUT
AUDIO OUT
Y
L
L
L
C
/
/
PB
B
R
R
COAXIAL
VIDEO OUT VIDEO IN
R
C
PR
R
1
2
3 4
5
6 7 8 9
1. AC Power Cord
6. AUDIO OUT jacks
Connect to a standard AC outlet to supply power to this unit.
2. COAXIAL DIGITAL AUDIO OUT jack (DVD only)
Use to connect an AV receiver, Dolby Digital decoder or other
device with a coaxial digital input jack with a digital coaxial cable.
3. AUDIO OUT jacks (DVD only)
Use to connect a TV monitor, AV receiver or other device with
an RCA audio cable.
4. S-VIDEO OUT jack (DVD only)
Use to connect the S-video input of a TV monitor, AV receiver
or other device with an S-video cable.
5. COMPONENT VIDEO OUT jacks (DVD only)
Use to connect a TV monitor with component video inputs
with a component video cable.
Use to connect a TV monitor, AV receiver or other device with
an RCA audio cable.
7. VIDEO OUT jack
Use to connect a TV monitor, AV receiver or other device with
an RCA video cable.
8. VIDEO IN jack (L1) (VCR only)
Use to connect external device with an RCA video cable.
9. AUDIO IN jacks (L1) (VCR only)
Use to connect external device with an RCA audio cable.
Note:
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic
discharge may cause permanent damage to the unit.
–
–
EN
7
E8EB5UD_SD-V296KU_EN_ES_v1.indd
7
2008/07/14 10:36:27
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
DVD mode
VCR mode
Media
Button
(Alphabetical order)
• To turn the unit on/off.
• To turn the unit on/off.
• To turn the unit on/off.
1
4
7
2
5
8
0
3
6
9
• To select chapter or title
directly.
• To select track or file directly.
+10
• To search forward/backward
through a disc.
• To begin slow forward/reverse
playback in the pause mode.
• To forward/backward a tape.
• To begin slow forward
playback in the pause mode.
• To search forward/backward
through a disc. (CD)
A-B
• To repeat between your cho-
sen point of A and B.
• To repeat between your
chosen point of A and B. (CD)
ANGLE
• To select camera angles on a
disc.
• To rotate a picture 90 degrees
clockwise. (JPEG)
AUDIO
• To select “HIFI” or “MONO”
mode during playback.
(Hi-Fi tapes only)
• To select audio languages on a • To select “STEREO”, “L-ch” or
disc.
“R-ch”. (CD)
• To clear the markers. (CD)
• To remove status number in
program input.
• To clear the markers.
• To clear numbers entered
incorrectly.
• To cancel the point A for A-B
repeat setting.
CLEAR/
C.RESET
• To exit the VCR menu.
• To reset the tape counter.
• To clear numbers entered
incorrectly.
• To cancel the point A for A-B
repeat setting. (CD)
DISPLAY
DVD
• To display the current disc
mode.
• To display the current disc
mode.
• To display the current time, tape
counter, “DISC“, “L1” or “L2”.
• To select DVD output mode.
• To activate DVD mode.
• To select the DVD output mode.
• To activate DVD mode.
• To select an item on
the VCR menu.
• To move the cursor and
determine its position.
Installing the Batteries for the
Remote Control
ENTER
• To advance to the
next VCR menu.
• To move the cursor and deter-
mine its position.
• To go back one step
during clock and
timer programming.
• To skip files. (JPEG)
Install two AA batteries (supplied) match-
ing the polarity indicated inside battery
compartment of the remote control.
INPUT
SELECT
• To select input “DISC”, “L1”or
“L2”.
MENU
MODE
• To call up the disc menu on a
disc.
• To call up the file list. (JPEG)
1
2
3
• To program the playing order
or play randomly.
• To set black level on/off.
• To set virtual surround on/off.
• To set virtual surround on/off.
(CD)
• To activate the Slide Show
mode. (JPEG)
OPEN/CLOSE
PAUSE
• To eject the cassette tape from
the cassette compartment.
• To open or close the disc tray. • To open or close the disc tray.
Keep in mind the following when using
the remote control:
• To pause tape playback or
recording.
• To advance playback one
frame at a time.
• To pause disc playback.
•
Make sure that there are no obstacles
between the remote control and the
infrared sensor window on the unit.
• To advance playback one
frame at a time.
• To pause disc playback.
• To begin disc playback.
• To begin disc playback.
• To begin tape playback.
PLAY
• The maximum operable ranges from the
unit are as follows.
REC/OTR
• To start recording or one-touch
timer recording (OTR).
- Line of sight: approx. 23 feet (7m)
- Either side of center:
• To play back a track or disc
repeatedly. (CD)
REPEAT
RETURN
• To play back a chapter or title
repeatedly.
• To select the repeat mode on/
off.
• To play back a file, folder or
disc repeatedly. (JPEG)
approx. 23 feet (7m) within 30°
• To return to the previous
operation in menu.
• To return to the previous
operation in menu.
SEARCH
MODE
• To search track.
• To search chapter, title or time.
• To set or search the markers.
• To call up the index or time
search menu.
• To search time. (CD)
• To set or search the markers. (CD)
SETUP
SKIP
• To call up the DVD setup menu. • To call up the DVD setup menu. • To call up the VCR menu.
23 feet (7m)
30˚
23 feet (7m)
30˚
• To skip chapters or titles.
• To skip tracks or files.
• To stop playback.
23 feet (7m)
SPEED
• To select the recording speed.
• To stop playback or recording.
Note:
STOP
• Do not mix alkaline and manganese
batteries.
• To stop playback.
SUBTITLE
• Do not mix old and new batteries.
• Always remove batteries from remote
control if they are dead or if the remote
control is not to be used for an extended
period of time. This will prevent battery acid
from leaking into the battery compartment.
• To select subtitles on a disc.
T-SET
• To put the VCR into standby
mode for a timer recording.
• To return to the top file of
the highest hierarchy in the
program and file list. (JPEG)
TOP MENU
• To call up the top menu on a
disc.
•
If you turn off this unit, [OPEN/CLOSE A] on
the remote control is not available.
Be sure to use [OPEN/CLOSE A] or
TRACKING
TRACKING
• To adjust the tracking manually
during playback.
VCR
• To select the VCR output mode.
• To activate VCR mode.
[
C/A (STOP/EJECT)] on the unit.
ZOOM
• To magnify part of a picture.
(2x/4x)
• To magnify part of a picture.
(2x) (JPEG)
–
–
EN
8
E8EB5UD_SD-V296KU_EN_ES_v1.indd
8
2008/07/14 10:36:31
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Display Panel
Displays a type of the disc
which is inserted on the tray.
• DVD: DVD-video
No disc inserted or
cannot read
• CD: Audio CD/JPEG on CD
Appears when the
A-B repeat function
is on.
Tray open
Appears when the
repeat function is on.
Appears when the
progressive scan
system is activated.
Tray closed
GROUP
P.SCAN
DVD
Loading the Disc
CD
Appears when
the ALL repeat
function is on.
Displays how long the current title or track
has been played back. When a chapter or track is
switched, the number of a new title,
chapter or track is displayed.
Appears when the
inserted disc comes
to a pause.
Appears when the inserted
disc is being played back.
Appears during slow motion
playback. (DVD)
VCR Display Panel
Appears when an OTR, timer recording,
or satellite link has been set.
Indicates a cassette tape is in the unit.
Appears during recording;
flashes when recording is paused.
REC
Appears when the auto repeat
function is on.
PM
Indicates current time is PM.
There is no AM indication.
Appears if cassette tape
playback is paused.
Appears during slow motion
Displays the elapsed playing time of a tape; also displays a selected
input mode, tape speed, remaining time for an
OTR or the current time.
playback.
Appears during cassette tape
playback.
Selecting DVD or VCR Operation
You must first select either DVD or VCR operation.
VCR MODE
Press [VCR] on the remote control.
(Verify that the VCR indicator is lit.)
VCR button
DVD button
DVD MODE
Press [DVD] on the remote control.
(Verify that the DVD indicator is lit.)
VCR/DVD button
VCR indicator
DVD indicator
–
–
EN
9
E8EB5UD_SD-V296KU_EN_ES_v1.indd
9
2008/07/14 10:36:46
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
If your TV has AUDIO/VIDEO input jacks, see the section “Connection to a TV” on this page. If not, it is still possible to connect this
unit to your TV by using a STEREO AUDIO/VIDEO RF modulator (commercially available). In this case, follow the instructions below.
Connection to RF Modulator (Not Supplied)
1) Disconnect the power cords of the devices from the AC outlet.
2) Connect the AUDIO/VIDEO output jacks of this unit to the AUDIO /
VIDEO input jacks of your RF modulator by RCA Audio/Video cables.
3) The antenna input jack of your TV may have been already
occupied. If so, disconnect the RF cable from your TV and then
connect the RF cable to your RF modulator (usually marked
“ANT IN”).
5) Set your RF modulator’s channel 3/4 switch to either 3 or 4,
whichever the TV channel is least used in your area. If your RF
modulator has a modulator/antenna switch, set it according to
your RF modulator’s manual.
6) Plug in the power cords of the devices to the AC outlet.
7) Turn on your TV and choose the same channel as you set the
RF modulator’s channel 3/4 switch to. For more details,
follow the instructions supplied with the RF modulator.
4) Connect your RF modulator to your TV by another RF cable.
If your TV does not have AUDIO / VIDEO input jack.
(Back of this unit)
Antenna
Cable
Signal
DVD
DVD/VCR VCR
AUDIO OUT AUDIO IN
COMPONENT
DIGITAL
AUDIO S-VIDEO
VIDEO OUT
OUT
OUT
AUDIO OUT
L
L
L
/
P
R
R
STEREO AUDIO / VIDEO RF Modulator
COAXIAL
VIDEO OUT VIDEO IN
R
C
PR
R
(commercially available)
AC 120V ANT IN CHANNEL TO TV VIDEO
AUDIO
3
4
R
L
(Back of TV)
1
RCA Audio/Video
Cables
(Supplied)
2
Note:
• The quality of picture may become
poor if the unit is connected to an RF
modulator.
RF Cable
3
(commercially available)
Antenna in jack
Connection to a TV
If your TV does not have AUDIO/VIDEO input jack, see the section “Connecting to RF Modulator (Not Supplied)” on this page.
VCR and Basic DVD Connection Available for DVD only
DVD’s picture quality
analog audio
standard picture
good picture
better picture
COMPONENT
VIDEO IN
COMPONENT
VIDEO IN
AUDIO IN
S-VIDEO IN
VIDEO IN
TV
Y
Y
L
R
C
B
PB
or
U
O
N
L
or
or
and
C
R
PR
R
V
I
D
E
O
I
N
RCA audio cable
RCA video cable
S-video cable
component video cable
This unit
DVD
AUDIO
OUT
DVD/VCR VC
AUDIO OUT
DVD/VCR VCR
DVD
DVD
AUDIO S-VIDEO
OUT OUT
COMPONENT
VIDEO OUT
COMPONENT
AUDIO S-VIDEO
VIDEO OUT
OUT
OUT
L
Y
DVD
DVD/VCR VCR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO OUT AUDIO IN
AUDIO OUT
O
U
T
O
U
T
L
Y
L
L
L
R
C
B
PB
/
R
R
COAXIAL
V
I
D
E
O
O
U
T
V
I
D
E
O
I
N
R
C
/
/
PB
B
C
PR
/
R
VIDEO OUT
R
C
PR
R
or
AUDIO OUT
COMPONENT
VIDEO OUT
VIDEO OUT
S-VIDEO OUT
If your TV is compatible with 525 (480) progressive
Supplied cables used in this connection are as follows:
scanning, and you want to enjoy that high quality picture
for DVD playing;
• RCA audio cable (L/R) x 1
• RCA video cable x 1
You must select the connection COMPONENT VIDEO OUT
above and progressive scanning mode. To set the mode, set
“PROGRESSIVE” to “ON” in “DISPLAY” menu, so that the “P. SCAN”
on the front panel display appears. Refer to pages 23-24 for
more details.
Please purchase the rest of the necessary cables at your local store.
Note:
• Connect this unit directly to your TV. If RCA audio/video cables are connected
to a VCR, pictures may be distorted due to the copy protection system.
• DIGITAL AUDIO OUT (COAXIAL), DVD AUDIO OUT, S-VIDEO OUT and
COMPONENT VIDEO OUT jacks are only useful in DVD mode.
If your TV is not compatible with progressive scanning;
Use this unit in interlace mode and set “PROGRESSIVE” to “OFF”
either in “DISPLAY” menu or by pressing and holding
[ B (PLAY)] on the front of the unit on the DVD side for more
than 5 seconds, so that the “P. SCAN” on the front panel display
disappears.
After connecting to your TV:
Press the input selector button (usually TV/VIDEO, INPUT or AUX)
on your TV to switch an appropriate external input channel (usually
near channel 0) for viewing the picture from this unit. If the picture
does not appear, also refer to the manual accompanying your TV.
–
–
EN
10
E8EB5UD_SD-V296KU_EN_ES_v1.indd 10
2008/07/15 16:14:58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to an Audio System
If using this DVD player to play back a DVD in a Dolby Digital Multi-channel surround or DTS surround format, the DVD player outputs a
Dolby Digital or DTS data stream from its COAXIAL DIGITAL AUDIO OUT jack.
By hooking up the player to a Dolby Digital or DTS decoder, you can enjoy more convincing, realistic ambience with powerful and high-
quality surrounding sound of a professional standard which can be heard in movie theaters.
Use a commercially available digital audio coaxial cable for the audio connections.
AV amplifier with a built in decoder
Stereo system
Method 1
AUDIO
Method 2
(AV control center), Dolby Digital decoder,
DTS decoder, MD deck or DAT deck
L
R
analog audio
input jacks
COAXIAL
digital audio
input jack
digital audio coaxial cable
RCA audio cable
DVD/VCR
AUDIO OUT
DVD
AUDIO
OUT
DVD
DIGITAL
AUDIO
OUT
AUDIO OU
L
DVD
DVD/VCR VCR
AUDIO OUT AUDIO IN
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO OUT
OUT
OUT
L
Y
L
L
L
R
C
B
PB
/
/
R
R
COAXIAL
V
I
D
E
O
O
U
T
V
I
D
E
O
I
N
R
C
PR
R
This unit
COAXIAL
R
AUDIO OUT (Analog)
• Method 1 DVD Player + Stereo system
• Method 2 DVD Player + AV amplifier with a built in decoder (AV control center), Dolby Digital decoder, DTS decoder, MD deck or DAT deck
DIGITAL AUDIO OUT
Note (for method 2 only):
Supplied cables used in this connection are as follows:
• When using an AV amplifier with a built in decoder (AV control center),
Dolby Digital, or DTS decoder as shown in the Method 2, set “DOLBY
DIGITAL” or “DTS” to “BITSTREAM” accordingly for audio output in the
setup mode (refer to pages 23-24). Set it to “PCM” or “OFF” for the decoder
that is not used currently. Playing back a DVD using incorrect settings may
generate noise distortion, and may also damage the speakers.
• The audio source on a disc in a Dolby Digital Multi-channel surround
format cannot be recorded as digital sound by an MD deck or DAT deck.
• Set “Dolby Digital” to “PCM” and “DTS” to “OFF” for audio output in the setup
mode for connecting to an MD deck or DAT deck (refer to pages 23-24).
• Harsh noise that could harm your ears or the speakers is generated
when a DVD recorded in DTS is played while using a decoder, etc., that
is not DTS-compatible.
• RCA audio cable (L/R) x 1
Please purchase the rest of the necessary cables at your
local store.
Note:
• Be sure to turn off the power of all components in the system before
connecting another component.
• Refer to the Instruction Manuals for your TV, stereo system and any
other components to be connected to the DVD player.
• When playing a copyright-protected 96kHz PCM DVD, the digital sound
will be down sampled at 48kHz, even if you set “DOWN SAMPLING” to
“OFF” (refer to pages 23-24).
Connection to an External Tuner
external tuner
(cable/satellite box)
rear of TV
rear of the unit
DVD
DVD/VCR VCR
AUDIO OUT AUDIO IN
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO OUT
OUT
OUT
Y
L
L
L
C
B
PB
/
/
R
R
COAXIAL
VIDEO OUT VIDEO IN
R
C
PR
R
A
U
D
I
O
I
N
L
L1
R
V
I
D
E
O
I
N
DVD/VCR VCR
AUDIO OUT
AUDIO IN
AUDIO OUT
AUDIO IN
RCA audio cable
RCA video cable
L
L
L
RCA audio cable
RCA video cable
L
R
R
R
R
VIDEO OUT
VIDEO IN
VIDEO OUT
VIDEO IN
Using the unit with an external tuner
Supplied cables used in this connection are as follows:
1. Connect RCA audio and video cables to the audio and video
output jacks of your external tuner and to the audio and video
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your
local store.
input jacks at the rear of the unit
.
2. Press [INPUT SELECT] on your remote control until “L1” is
displayed on your TV.
Special note when connected to an external tuner:
• Only the active channel on your external tuner may be viewed or
recorded when connected to this unit.
Do not change channels during a recording. You cannot record
on channel while viewing another.
• Always use the LEFT (white) audio output jack from the external
tuner to ensure that the audio is mixed down correctly to mono
for this unit. If you use the RIGHT (red) jack, you will record the
right audio only.
Note:
• Your cable/satellite box can be accessed only by connecting it to L1
(rear panel jacks) of the unit. Even if the unit is turned off, the signal
from the external tuner is output to the TV through the unit.
L1: Rear panel terminals
L2: Front panel terminals
Refer to “Front Panel” and “Rear Panel” on page 7 for more
information.
–
–
EN
11
E8EB5UD_SD-V296KU_EN_ES_v1.indd 11
2008/07/14 10:36:50
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation for Use
Turning on Unit for the First Time
Clock Setting
VCR
VCR
Please note: most instructions in this man-
ual refer to remote control use.
Press [SETUP] and select “CLOCK SET”.
- M E N U -
Be sure your TV’s input is set to VIDEO. (Name may
vary with TV manufacturer. See your TV manual for
details.)
1
1
2
TIMER PROGRAMMING
SATELLITE LINK
Then press [B] to go to next step.
AUTO REPEAT [OFF]
CLOCK SET
B
SETUP
LANGUAGE SELECT
or
Select your on-screen language.
Then press [B] to continue.
LANGUAGE SELECT
B
ENGLISH
[ON]
FRANCAIS
ESPAÑOL
• If the clock is not set, “CLOCK SET” menu appears when you press
[SETUP]. In this case, go to step 2.
or
CLOCK SET
Select the current month.
Then press [B] to go to next step.
2
3
4
5
6
7
8
MONTH DAY
1 0 - -
YEAR
- - - -
/
When “CLOCK SET” menu appears,
go to step 2 in “Clock Setting” on this page.
CLOCK SET
3
HOUR MINUTE
AM/PM
- -
MONTH DAY
1 0 – –
YEAR
- -
:
- -
/
– – – –
or
HOUR MINUTE
– – – –
AM/PM
– –
:
or
CLOCK SET
Select the current day.
Then press [B] to go to next step.
MONTH DAY
1 0 0 7
YEAR
- - - -
/
HOUR MINUTE
AM/PM
- -
- -
:
- -
or
To Change the Selected On-screen Language
CLOCK SET
Select the current year.
Then press [B] to go to next step.
- M E N U -
MONTH DAY
1 0 0 7
YEAR
TUE 2 0 0 8
Press [SETUP] until the main menu appears.
/
1
B
TIMER PROGRAMMING
SATELLITE LINK
HOUR MINUTE
- - - -
AM/PM
- -
SETUP
:
AUTO REPEAT [OFF]
CLOCK SET
or
LANGUAGE SELECT
CLOCK SET
Select the current hour.
Then press [B] to go to next step.
- M E N U -
MONTH DAY
YEAR
TUE 2 0 0 8
Select “LANGUAGE SELECT”.
Then press [B] to go to next step.
1 0 0 7
/
2
TIMER PROGRAMMING
SATELLITE LINK
HOUR MINUTE
0 5 - -
AM/PM
- -
AUTO REPEAT [OFF]
CLOCK SET
:
or
B
LANGUAGE SELECT
or
CLOCK SET
Select the current minute.
Then press [B] to go to next step.
MONTH DAY
YEAR
TUE 2 0 0 8
Select “ENGLISH”, “FRANCAIS” or
“ESPAÑOL”. Then press [SETUP].
LANGUAGE SELECT
1 0 0 7
/
3
B
ENGLISH
FRANCAIS
ESPAÑOL
[ON]
HOUR MINUTE
0 5 4 0
AM/PM
- -
:
or
SETUP
or
CLOCK SET
Select “AM” or “PM”.
MONTH DAY
YEAR
TUE 2 0 0 8
Note:
1 0 0 7
/
• If you accidentally select Spanish or French and need English:
HOUR MINUTE
0 5 4 0
AM/PM
P M AM
B PM
or
:
Press [SETUP] and choose
“
SELEC. IDIOMA
”
or “SELECTION LANGUE”.
Press [B] and select “ENGLISH”. Finally, press [SETUP].
Press [SETUP] to exit “CLOCK SET” menu.
SETUP
Note:
• To go back, press [s] during steps 2 to 7.
• Clock setting will be lost after a power failure, or this unit has been
unplugged for more than 30 seconds.
–
–
EN
12
E8EB5UD_SD-V296KU_EN_ES_v1.indd 12
2008/07/14 10:36:52
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR FUNCTIONS
Playback
Before: Turn on the TV.
Note:
4
1
VCR
• When a cassette tape
without a record tab is
inserted, the unit will start
playback automatically.
• Tracking will be
automatically adjusted
upon playback. To adjust
the tracking manually,
use [TRACKING K / L]
Insert a cassette tape
into this unit.
To start playback
1
2
4
PLAY
To stop playback
To eject the cassette tape
3
OPEN/CLOSE
2
([TRACKING
/
] on
STOP
this unit) during playback.
3
4 3 2
When You Playback a Cassette Tape Recorded in Hi-Fi Stereo
Press [AUDIO
] on the remote control, then select “HIFI” or “MONO”.
Your selection
Type of recorded tape
Hi-Fi tapes recorded in
Hi-Fi stereo
HIFI
MONO
• During playing back non Hi-Fi tapes, [AUDIO
] on the remote control is not
L-channel R-channel
available.
L
R
L+R
Other Operations
To cue or review picture during playback (picture search)
To play back in slow motion (slow mode)
Use [g] or [h] ([ g (FWD)] or [ h (REW)] on this unit).
• Press it again and the unit will search in super high speed. (in the
SLP mode only)
Press [PAUSE F] during playback, then press [g] ([ g (FWD)] on
this unit).
• If you want to change speed in slow mode, press [g] or [h
([ g (FWD)] or [ h (REW)] on this unit), slow speed will be
more fast or slow mode.
]
To freeze the picture on TV screen during playback (still mode)
Press [PAUSE F]. Each time you press the button, the picture will
be forwarded by one frame.
•
If the noise bars appear on the TV screen, you can reduce it by using
[TRACKING K / L] ([TRACKING ] on this unit)
/
.
• If the picture begins to vibrate vertically in the still mode, stabilize
To rewind the cassette tape automatically (auto rewind)
the picture by using [TRACKING K / L] ([TRACKING
/
] on
When a cassette tape reaches its end during playback, fast-forward
or recording (except timer recording and one-touch timer recording),
the cassette tape will automatically rewind to the beginning. After
rewinding finishes, the unit will eject the cassette tape.
this unit).
• If the picture is distorted or rolling vertically, adjust the vertical
hold control on your TV if equipped.
To reset the cassette tape counter (counter reset)
Note:
Press [DISPLAY] to display the cassette tape counter on the TV.
• To prevent damage to the cassette tape, still or slow mode will
automatically stop after 5 minutes.
Press [CLEAR/C.RESET] to reset the counter to “0:00:00”.
• To return to playback from the picture search, still or slow mode, press
[PLAY B].
Time Search
Index Search
To search by index mark. The index mark will be made
automatically at the beginning of each recording.
To search by length of time.
VCR
VCR
• Insert a cassette tape into this unit.
• Insert a cassette tape into this unit.
Press [SEARCH MODE] twice.
1
2
TIME SEARCH
– : – –
Press [SEARCH MODE] once.
SEARCH
MODE
1
SEARCH
MODE
INDEX SEARCH
– –
Select the desired length of time
for fast forwarding or rewinding.
To select index mark
TIME SEARCH
2 : 5 0
2
INDEX SEARCH
0 3
01 ~ 20
0:01~ 9:59
or
beginning of
the contents
current program
end of the
contents
or
(1 minute~9 hours and 59 minutes)
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
To rewind
02
01
01
02
03
3
4
ss
index mark
To rewind
3
4
ss
To fast forward
BB
To fast forward
BB
When selected length of time is
reached, playback will start
automatically.
PLAY
B
When index mark is reached,
playback automatically begins.
PLAY
B
Note for Index Search & Time Search:
• These functions are not available during recording.
• Press [STOP C] to stop the search.
• If a cassette tape ends during a search, your search will be canceled and
Note:
• The time gap between index marks should be more than 1 minute for SP
mode, 2 minutes for LP mode and 3 minutes for SLP mode.
the cassette tape will rewind to the beginning.
–
–
EN
13
E8EB5UD_SD-V296KU_EN_ES_v1.indd 13
2008/07/14 10:37:03
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Repeat
The unit will automatically rewind the cassette tape when it has reached the end and will automatically start playback unless you press
[STOP C] or you turn off the unit.
VCR
- M E N U -
- M E N U -
Press [SETUP], and choose “AUTO REPEAT”.
Press [B] to “AUTO REPEAT” to set “ON” or “OFF”.
1
2
TIMER PROGRAMMING
SATELLITE LINK
TIMER PROGRAMMING
SATELLITE LINK
B
AUTO REPEAT [ON]
CLOCK SET
B
AUTO REPEAT [OFF]
CLOCK SET
SETUP
LANGUAGE SELECT
LANGUAGE SELECT
or
Press [SETUP] to exit.
Note:
• The auto repeat function can also be set “ON” or “OFF” by pressing [REPEAT] on the remote control.
• To cancel auto repeat function, follow step 1 above. Then, press [B] so that “OFF” appears beside “AUTO REPEAT”. Press [SETUP] to exit.
• The auto repeat playback will start automatically if you select “AUTO REPEAT” to “ON” in the stop mode.
Recording
This unit has no tuner system so it cannot receive TV broadcasts without external
tuner or such devices.
Note:
TV
this unit
external tuner
• You can also set to external tuner. Refer to “Satellite Link” on page 16.
Recording & One-touch Timer Recording (OTR)
VCR
6
3
2
Insert a recordable
cassette tape.
Press [INPUT SELECT] until “L1” or
“L2” is displayed on the TV screen.
Select “L1” to activate rear input jacks.
Select “L2” to activate front input jacks.
1
2
INPUT
SELECT
5
4
See note on the right.
1
5 6
4
Press [SPEED] to select the desired tape speed.
3
4
5
To stop recording temporarily (pause mode)
SPEED
Tape speed
Type of tape
SP mode
Recording / playback time
Press [PAUSE F].
T60
T120
T160
2-2/3hours
8hours
• During the recording in pause mode, 5
C
marks appear on the
mark represents 1 minute.
• Press it again to resume recording.
1hour
3hours
2hours
6hours
TV screen. Each
C
SP
SLP mode
• Pause mode will be automatically canceled after 5 minutes to
prevent damage to the cassette tape and the video head.
Press [REC/OTR] until desired recording time is selected.
REC/OTR
REC
(normal recording)
OTR (0:30)
OTR (1:00).....
OTR (7:30)
Note:
• Do not change the external tuner’s channel while you are recording.
You CANNOT watch one channel and record another at the same time.
• Connect your external tuner to the L1 (rear panel) jacks of the unit.
Connect camcorders and other such devices to the L2 (front panel)
jacks. Refer to page 11.
OTR (8:00)
REC
Press [STOP C] to
stop recording.
Press [OPEN/CLOSE A] to eject the
recorded cassette tape.
6
OPEN/CLOSE
STOP
Accidental Erasure Prevention
To prevent accidental recording, remove erase-
protection tab of the cassette tape. To record
on it later, cover the hole with adhesive tape.
erase-protection tab
Timer Recording
VCR
• Insert a recordable cassette tape.
• Make sure to turn on the external
tuner.
Press [SETUP]. Select “TIMER PROGRAMMING”.
Select an empty program number.
Then press [B] to go to next step.
PROGRAM NUMBER
DATE – – / – –
START TIME – – : – – – –
1
1
2
- M E N U -
TIMER PROGRAMMING
PROG 12345678
DATE
START TIME
END
L1/L2
REC
TIME – – : – – – –
– –
SPEED – –
B
TIMER PROGRAMMING
SATELLITE LINK
SETUP
AUTO REPEAT [OFF]
CLOCK SET
or
END
TIME
LANGUAGE SELECT
L1/L2
REC SPEED
Available program number flashes.
–
–
EN
14
E8EB5UD_SD-V296KU_EN_ES_v1.indd 14
2008/07/14 10:37:13
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE TIME PROGRAM
PROGRAM NUMBER
Select “ONCE”, “DAILY” (Mon-Fri), or “WEEKLY”.
Then press [B] to go to next step.
Select recording speed.
Then press [SETUP].
PROGRAM NUMBER
1
3
4
9
1
B
ONCE
DATE
1 0 / 0 7 TUE
DAILY
WEEKLY
START TIME 0 7 : 3 0 PM
END
L1/L2
REC
TIME 0 8 : 3 0 PM
L1
SETUP
or
SPEED SP
or
B
SP
SLP
•
[B].
To set another program after step 9, press
Then continue with step 2.
Select the desired date.
Then press [B] to go to next step.
ONE TIME PROGRAM
PROGRAM NUMBER
Press [T-SET] to set the timer standby mode.
or
10
1
DATE
1 0 / 0 7 TUE
T-SET
START TIME – – : – – – –
END
L1/L2
REC
TIME – – : – – – –
– –
SPEED – –
•
indicator on this unit lights up and the unit goes to
TIMER REC
the DVD mode.
or
• You can program the unit to record up to 8 programs, for up to
a year in advance.
Note:
• To go back one step, press [s] during steps 3 to 9.
• Select “L1” to activate rear input jacks. Select “L2” to activate front input
jacks.
Select the desired starting time (hour/minute).
5
6
Then press [B] to go to next step.
ONE TIME PROGRAM
or
PROGRAM NUMBER
DATE 1 0 / 0 7 TUE
START TIME 0 7 : 3 0 – –
1
To check, correct or cancel a timer program
END
L1/L2
REC
TIME – – : – – – –
– –
SPEED – –
1) Press [T-SET] then, [VCR] on the remote control.
2) Press [SETUP] to call up the main menu.
3) Select “TIMER PROGRAMMING” by using [K / L], then press
[B].
4) Select the program number which you want to check by
using [K / L]. The details of the program you selected will
appear on the TV screen.
or
ONE TIME PROGRAM
PROGRAM NUMBER
Select “AM” or “PM”.
Then press [B] to go to next step.
1
DATE
1 0 / 0 7 TUE
START TIME 0 7 : 3 0 PM
END
TIME – – : – – – –
L1/L2
REC
– –
SPEED – –
AM
• Go to the digit you want to change by using [s / B]. Then,
enter correct numbers by using [K / L].
or
B
PM
• You may cancel the entire program by pressing [s] while
the program number blinks.
5) Press [SETUP] to exit.
Repeat the procedure in steps 5 and 6 to set the ending time.
7
8
6) Press [T-SET] to return to the timer standby mode.
ONE TIME PROGRAM
Select “L1” or “L2”.
Then press [B] to go to next step.
PROGRAM NUMBER
DATE 1 0 / 0 7 TUE
START TIME 0 7 : 3 0 PM
1
To cancel a timer recording in progress
Press [ C/A (STOP/EJECT)] on the unit.
END
L1/L2
REC
TIME 0 8 : 3 0 PM
L1
or
SPEED – –
Note:
• You cannot stop a started Timer Recording with [STOP C] on the remote
control.
Notes for Timer Recording & One-touch Timer Recording (OTR)
• If a cassette tape is not in the unit or does not have the erase-protection tab, TIMER REC and “ ” indicator on this unit blinks and
timer recording cannot be performed. Please insert a recordable cassette tape.
• When timer recordings are set, TIMER REC and “ ” indicator on this unit lights up. To use the VCR as usual until the time for the
recording, press [T-SET] so that TIMER REC and “ ” indicator lights off.
After an one-touch timer recording or a timer recording has been set, this unit operates as follows:
• If a cassette tape runs out before an one-touch timer recording or a timer recording is finished, the unit ejects the cassette tape. Press
[T-SET] on the remote control or [ C/A (STOP/EJECT)] on the unit, then press [VCR] to activate the VCR function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [T-SET] is pressed.
• To cancel the timer standby mode, press [T-SET] on the remote control or [ C/A (STOP/EJECT)] on the unit, then press [VCR] to
activate the VCR function again.
When an one-touch timer recording or a timer recording is completed...
• If auto power off for DVD has been activated and there are timer recordings on standby, the unit turns off automatically, and TIMER
REC and “
indicator on this unit lights to indicate the unit is in the timer standby mode.
”
• TIMER REC and “
indicator on this unit flashes if there are no more timer recordings on standby.
”
• If auto power off for DVD has NOT been activated, the unit goes to the DVD mode and all the VCR functions will be unavailable. All the
DVD functions are available during one-touch timer recording, timer standby mode and timer recording.
•
Press C/A (STOP/EJECT)] on this unit or [T-SET] on the remote control to use the VCR when the unit is turned off.
[
• Press [VCR/DVD] on this unit or [VCR] on the remote control to use the VCR when the unit is turned on. In case timer recording is in
standby mode, press [ C/A (STOP/EJECT)] on this unit or [T-SET] on the remote control, and then press [VCR/DVD] on this unit or
[VCR] on the remote control.
If you want to use the DVD player during a timer recording or while TIMER REC and “ ” indicator on this unit is on or blinking.
• Press [I/y (ON/STANDBY)] to turn on the unit. Press [DVD] on the remote control to choose DVD mode, then continue with the other
DVD features as described in this manual.
Note for timer recording:
•
If there is a power failure or the unit is unplugged for more than 30 seconds, clock setting and all timer programs will be lost.
–
–
EN
15
E8EB5UD_SD-V296KU_EN_ES_v1.indd 15
2008/07/14 10:37:20
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Link
You can set the unit to start recording whenever it detects a video signal from the external tuner.
Preparing for the Satellite Link Timer Recording:
Preparation on the tuner
Preparation on this unit
• Satellite link accepts only the connection from L1 (rear) with the
external tuner. (The connection from L2 cannot read any signals
from the external tuner.)
L1
external tuner
DVD
AUDIO
OUT
DVD/VCR VCR
AUDIO OUT
COMPONENT
VIDEO OUT
S-VIDEO
OUT
DIGITAL
AUDIO IN
AUDIO OUT
Y
C
L
L
•
The external tuner should be equipped with some kind of timer
function. Using timer function of the tuner, set it to output audio/video
signals when it comes to the time you want to start recording, and
stop output audio/video signals when it comes to the time you want to
finish recording. Refer to the tuner’s manual on how to set the timer.
L
/
/
PB
B
R
R
COAXIAL
VIDEO OUT VIDEO IN
R
C
PR
R
RCA audio/video cables
• Make sure to turn off the tuner when you finish setting.
Note:
• Please purchase the necessary cables at your local store. (Refer to page 7.)
VCR
Press [SPEED] to select the desired tape speed.
Set the desired start minutes.
If you wish to go back to the left, press [s ].
SATELLITE LINK
1
5
SPEED
Tape speed
Type of tape
SP mode
Recording / playback time
T60
1hour
0 1
:
0 0 PM
T120
2hours
6hours
T160
2-2/3hours
8hours
or
SP
SLP mode
3hours
Press [B] to set satellite link standby mode.
SATELLITE LINK
6
In stop mode, press [SETUP].
2
3
SETUP
0 1
:
3 0 PM
[ON]
- M E N U -
Select “SATELLITE LINK”.
Then press [B] to go to next step.
TIMER PROGRAMMING
SATELLITE LINK
• TIMER REC indicator on this unit lights up and the unit goes to the
DVD mode. If you do not use DVD function, turn off the unit.
• Satellite unit must be turned on for VCR satellite link to start.
If an external tuner is not set to output signals, satellite link will
remain in standby mode.
B
AUTO REPEAT
CLOCK SET
[OFF]
LANGUAGE SELECT
or
Set the desired start hour.
Then press [B] to go to next step.
SATELLITE LINK
4
To cancel the satellite link function in standby mode:
Press [T-SET] on the remote control or [ C/A (STOP/EJECT)] on
this unit.
1 2
:
0 0 AM
or
To cancel the satellite link function while the satellite link
recording is in progress:
Press [ C/A (STOP/EJECT)] on this unit.
• The hour can be selected from 1-12 with AM or PM.
• When the external tuner signal is stopped, recording will be stopped.
Note:
• You cannot stop the satellite link recording with [STOP C] on the remote
control.
Note:
• If you have not set the clock, “CLOCK SET” menu will appear at step 2. Refer to “Clock Setting” on page 12.
• You cannot set the ending time for the satellite link timer recording on this unit.
• Recording picture will be distorted if the copy protection signal is being detected during satellite link timer recording.
• When a regular timer recording and the satellite link timer recording are overlapped, those recordings are recorded as illustrated below.
e.g.) In case of the satellite link timer recording is overlapped
on the existing timer recording.
e.g.) In case of the timer recording is programmed in the middle
of the satellite link timer recording
e.g.) In case of the timer recording is overlapped on the existing
satellite link timer recording.
timer recording
satellite link
timer recording
satellite link
timer recording
satellite link
recording result
recording result
recording result
Copying a Cassette Tape
output jacks of
Warning: Unauthorized recordings of copyrighted cassette tapes
rear of the unit
L1
external device
may be an infringement of copyright laws.
AUDIO OUT
L
DVD/VCR VCR
AUDIO OUT AUDIO IN
RCA audio/video
or
1) Insert a pre-recorded cassette tape into another external
device for playback.
L
L
R
R
R
cables
VIDEO OUT VIDEO IN
VIDEO OUT
2) Insert a recordable cassette tape into this unit for recording.
3) Press [SPEED] on the remote control to select recording
speed (SP or SLP).
4) Press [INPUT SELECT] on the remote control to select L1 or
L2. Choose L1 if device is connected to rear input jacks, or L2
if connected to the front. Refer to “Front Panel” and
“Rear Panel” on page 7 for more details.
You can use a video disc player, cable/satellite box or other audio/video
component with audio/video output jacks.
Note:
• For best results during dubbing, use buttons on this unit whenever
possible. The remote control might affect another device’s operation.
• Always use video-quality shielded cables with RCA-type connectors.
Standard audio cables are not recommended.
5) Press [I REC] on the unit.
6) Press “PLAY” button on the external device.
7) To stop recording, press [ C/A (STOP/EJECT)] on this unit,
then stop playback of the external device.
• L2 input jacks are on the front of this unit.
• Please purchase the necessary cables at your local store. (Refer to page 7.)
–
–
EN
16
E8EB5UD_SD-V296KU_EN_ES_v1.indd 16
2008/07/14 10:37:28
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD to Cassette Tape Duplication
This will be possible only if the DVD is not copy protected.
Before you begin:
• Insert a cassette tape in the cassette compartment. Make sure
the tape’s record tab is intact and the tape is long enough to
record the DVD.
• Insert the DVD you want to copy in the disc tray.
• Turn on the TV and set it to the correct Video In channel. (Check
your TV owner’s manual for details.)
Press [SPEED] repeatedly until the desired tape speed (SP or SLP)
appears briefly on the screen.
For details about tape speed, refer to page 16.
3
Press [REC/OTR] to start recording. “REC” will appear on the display
panel.
4
5
Press [DVD]. Press [PLAY B] to play back the disc.
• To pause the recording, press [VCR], then press [PAUSE F] once.
REC indicator on this unit will flash.
• To resume recording, press [REC/OTR] or press [PAUSE F] again.
REC indicator on this unit will light up again.
Press [DVD]. Press [PLAY B] to play back the disc, then press
[PAUSE F] at the point where you want to start the recording.
1
• To stop recording, press [VCR], then press [STOP C].
Press [VCR] so VCR indicator lights up on the
front panel.
DISC
2
Press [INPUT SELECT] repeatedly until
“DISC” appears on the TV screen.
Note:
• A Timer Recording or Satellite Link is not available during DVD to
cassette tape duplication.
DVD FUNCTIONS
Playback
Before:
1
Turn on the TV, amplifier and any other
components which are connected to this
unit. Make sure the TV and audio receiver
(not supplied) are set to the correct
channel.
1
DVD
3
4
Insert a disc with
label facing up.
1
3
2
4
1
2 4 3
Lights up when power is on.
OPEN/CLOSE
Note:
• When you play a JPEG-format disc, details on page 19.
• “
” may appear at the top-right on the TV screen when the operation is prohibited by
the disc or this unit.
• Some DVD may be played from title 2 or 3 due to specific programs.
• Some discs may not start playback automatically. Then, press [PLAY B] to start playback.
• During the playback of a 2-layered disc, pictures may stop for a moment. This happens while the 1st
layer is being switched to the 2nd layer. This is not a malfunction.
To start playback
To stop playback
STOP
PLAY
• You can change the on-screen language for DVD function in “PLAYER MENU” menu. Refer to page 23.
Disc Menu
Paused and Step-by-Step Playback
DVD
DVD
Some discs contain menus which allow you to customize DVD
playback. Use [K / L / s / B] to select an item, then press
[ENTER] (or [PLAY B]).
Press [PAUSE F] during playback.
To continue playback, press [PLAY B].
DVD
Calling Up a Menu Screen during Playback
The disc goes forward by one frame each time [PAUSE F] is
pressed in the pause mode.
DVD
To continue playback, press [PLAY B].
• Press [MENU] to call up the disc menu.
• Press [TOP MENU] to call up the title menu.
Note:
• For DVD, set “STILL MODE” to “FIELD” in “DISPLAY” menu if pictures in
the pause mode are blurred. Refer to pages 23-24.
Note:
• Menu operations may vary depending on the disc. Refer to the manual
accompanying the disc for details.
To use [SKIP H / G]
DVD
Resume Playback
DVD
Press [SKIP
G
H
] once to skip to the next title, chapter or track.
Press [SKIP
] twice (once for JPEG) in quick succession to skip
Press [STOP C] during playback.
back to previous title, chapter or track.
For JPEG files, [s / B] is also available.
Resume message will appear on the
Resume ON
TV screen.
Fast Forward / Reverse Search
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
Press [PLAY B], playback will
DVD
resume from the point at which
E
1
playback was stopped.
e.g.) DVD
Press [g] or [h] repeatedly during playback to
select the required forward or reverse speed.
To continue playback, press [PLAY B].
Note:
• To cancel resume, press [STOP C] one more time in the stop mode.
• For JPEG, playback will resume from the beginning of the track at which
playback was stopped.
Note:
• The resume playback information stays on even when the power is
turned off, as long as the disc stays in the unit.
•
For DVD, fast forward or reverse search speed is different depending on the
disc. Approximate speed is 1(2x), 2(8x), 3(20x), 4(50x), 5(100x).
• For audio CD approximate speed is 1(2 ), 2(8 ), 3(30 ).
x
x
x
–
–
EN
17
E8EB5UD_SD-V296KU_EN_ES_v1.indd 17
2008/07/14 10:37:33
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow Forward / Reverse Search
Zoom
DVD
DVD
1
Press [g] or [h] repeatedly in the pause mode to
select the required forward or reverse speed.
To continue playback, press [PLAY B].
1) Press [ZOOM] during playback.
2) Press [ZOOM] repeatedly to select the required zoom factor:
2x, 4x or off.
x2
x4
Note:
• Slow forward or reverse speed is different depending on the disc.
Approximate speed is 1(1/16x), 2(1/8x), 3(1/2x).
• Set “STILL MODE” to “FIELD” in “DISPLAY” menu if pictures in the slow
playback mode are blurred. Refer to pages 23-24.
3) Use [K / L / s / B] to slide the zoomed picture across the TV
screen.
4) To exit zoom mode, press [ZOOM] to select OFF.
Note:
• Zoom function does not work while the disc menu is displayed.
• 4x zoom is not available on some discs.
• It may take several seconds to slide the zoomed picture.
• Only 2x zoom is available on JPEG files.
• Navigation screen is not available on JPEG.
• You cannot pan through the zoomed picture on some JPEG files.
On-Screen Display
You can check the information about the current disc by pressing [DISPLAY] on the remote control.
DVD
DVD
appears only in a case multi-
angle is available on the DVD.
DISPLAY
DISPLAY
current playback status
current playback status
4/12 0:03:21 - 0:02:15
T
1
2
11/16 0:00:00 - 0:03:30
1
remaining time of the current track
elapsed time of the current track
remaining time of the current
chapter
TR(Track):
DISPLAY
elapsed time of the current
chapter
current track number / total tracks
ALL:
current track number / total tracks
CH(Chapter):
current chapter number /
total chapters
4/12 0:13:45 - 0:45:40
T
current repeat setting, if active
DISPLAY
T:
A:
Track repeat
All Tracks repeat
A
B: A-B repeat
1/3 0:00:00 - 1:23:45
2
3
remaining time of the entire disc
elapsed time of the entire disc
remaining time of the current title
elapsed time of the current title
TT(Title):
current title number / total titles
DISPLAY
3
DISPLAY
Note:
layer numbers, appears only when
playing a two-layered disc.
• When you are playing a disc in program or random mode,
PROGRAM (or RANDOM) will be displayed instead of
T
L1
2
.
L0:
L1:
Layer 0 is playing
Layer 1 is playing
DVD
current repeat setting, appears
only when the repeat setting is
active.
DISPLAY
C:
T:
Chapter repeat
Title repeat
The name of the file currently in
play will be displayed.
1
2
TRACK 01
A
B: A-B repeat
bit rate: the amount of audio and
video data currently being read
DISPLAY
Current playback status
DISPLAY
TR(Track):
Current track number / Total tracks
4
1/36
T
Current repeat setting, if active
T : Track repeat
G: Group (folder) repeat
A: Disc repeat
DISPLAY
PROGRAM
RANDOM
3
4
or
(Only when you are playing a disc in PROGRAM or RANDOM mode.)
DISPLAY
–
–
EN
18
E8EB5UD_SD-V296KU_EN_ES_v1.indd 18
2008/07/14 10:37:43
Download from Www.Somanuals.com. All Manuals Search And Download.
|