TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-R2612
CD-RW/DVD-ROM COMBINATION MOBILE DRIVE
USER MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION – SD-R2612
General Features
CD-RW disc write/rewrite at 4X – 24X
CD-R disc write at 4X - 24X
3-way Disc Eject (eject button, software, emergency eject hole)
Average Access Time
CD
130ms
DVD-ROM (single) 130ms
DVD-ROM (dual)
DVD-RAM
150ms
250ms
Horizontal or Vertical Mount
2MByte Buffer
Playback interchangeability for CD-ROM and DVD-ROM discs
Regionalization (RPC2 compliance) (DVD)
BUS Interface
ATAPI
Format Compatibility
CD:
•
•
•
•
•
•
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data\
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video Video-
CD (White Book) - MPEG1 Video
DVD
•
•
•
•
•
•
•
•
DVD DVD-ROM (Book 1.02)
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0) DVD RW DVD-RAM P
DVD+R (Version 1.0)
DVD RW
DVD-RAM
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
Figure 1.SD-R2612 CD-RW/DVD Combo Drive Front Panel
Load disc using tray.
Loading
Tray
The LED lights green or amber when the drive is operating (LED is amber when drive is
writing.)
Busy
Indicator
The Eject button is used to open the disc tray so you can install or remove a disc.
Eject
Button
The emergency eject hole is to be used only when the Loading Tray will not open when
Eject button is pressed.
Emergency
Eject Hole
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP – SD-R2612
Toshiba recommends that only trained professionals install this CD-RW/DVD-ROM Combo drive into
your laptop/notebook.
Installation Notes
•
•
The SD-R2612 CD-RW/DVD-ROM Combo drive has no jumpers that need to be set
Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30°
(drive with volume control in up position).
•
•
When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive.
When mounting drive, the tightening torque of the four screws must be even. Recommended
screw tightening torque is 2N
•
For clearance around the front bezel, it is recommended that a clearance of more than 0.8mm
should be left in all directions.
Software Driver
Toshiba's SD-R2612 drive does not require any unique device drivers for Windows '98/2000/XP/NT.
After installing your drive and re-booting, your system should recognize your drive. Win '98/2000/XP/NT
Operating Systems support all Toshiba's ATAPI drives natively. If you prefer using DOS, download the
ATAPI driver from our web site.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE CD-RW/DVD-ROM Combo Drive – SD-R2612
Drive Operation
Inserting Media
To insert media perform the following steps:
Figure 1.Inserting Disc
1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray.
2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc.
3. Gently close the disc tray.
Removing Media
To remove media disc from the drive, perform the following steps:
1. Open the loading tray by pressing the Eject Button, and pulling tray out.
2. Grasp disc by it's outer edge, and lift out of loading tray.
3. Gently close the loading tray.
Usage Guidelines
•
•
•
Keep the disc tray closed when not using the CD-RW/DVD-ROM Combo drive
Do not press down on the disc tray when opening or closing it.
Do not place objects on the disc tray
•
•
Never use a damaged, broken, or deformed disc
Do not press the Eject button while the drive is playing a DVD movie or accessing a disc. To
stop a DVD movie, click Stop button in the DVD player application program
4
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of
the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high
speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-
speed technology and do not indicate a problem with the drive.
Regional Coding
Region Protection Coding (RPC) of DVD Discs: this feature is supported on DVD Players and is used
with DVD-Video Discs (i.e. movies). Currently, the motion picture industry has divided the world into
different regional "zones." These regions or "zones" correlate to the regional markets into which the
motion picture industry releases movies. Simply put, RPC Codes are placed on Movie Discs marketed
throughout the world based on the region of the world where they are being sold. These RPC codes
help to control and prevent the pirating of new release movies into other motion picture market regions
prior to their true release dates within those markets.
The SD-R2612 DVD-ROM/CD-RW drive supports the current RPC phase 2 industry specifications. This
means that when the DVD-ROM drive ships from the factory it is set to the region for which the
Operating System was intended. In other words the drive is set to support the Region 1 (North America)
Operating System and will only play Region 1 (North America) DVD-Video movie discs.
Emergency Ejection
CAUTION: The following procedure is intended only as a last resort when
pressing the eject button fails to open the Loading Tray.
1. Turn computer power OFF by properly shutting down system.
2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in as shown in the
picture below.
3. Loading tray will open/eject.
Figure 2.Using Emergency Eject
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Media
DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD
movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-
related and can be remedied by proper handling and care of media.
Cleaning Media
Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc
accessing speed.
If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather
from the inner side outward.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING – SD-R2612
Problem
Solution
Disc tray cannot be opened
•
•
Check that there is power to drive.
Use Emergency Eject instructions to open tray.
Drive is not recognized by
system
•
•
Is the drive connected properly? Are all cables plugged in
properly (e.g. Power Cable, Interface Cable and Audio Cables).
Is the software driver loaded? On a step-by-step (F8) Boot of the
system is the CD-RW/DVD-ROM Combo drive recognized?
(BIOS / DOS reports "device driver not found" or "no valid
drivers selected."). If not, Contact Technical Support.
•
•
•
Has the CD-RW/DVD-ROM Combo drive software driver been
corrupted by a virus. Run a Virus Scan program and repair if
possible. Contact Technical Support if the Virus renders the CD-
RW/DVD-ROM Combo drive software drivers not useable.
Drive is not recognized by
system during Boot process,
but is recognized by the
Operating System (i.e. XP,
Win2000, Win98, Win NT, etc.)
Is the CD-RW/DVD-ROM Combo drive software driver loaded?
On a step-by-step (F8) Boot of the system is the CD-RW/DVD-
ROM Combo drive recognized?
(BIOS / DOS reports "device driver not found" or "no valid DVD
drivers selected."). If not, Contact Technical Support.
Has the Windows CD-RW/DVD-ROM Combo drive software
driver program been corrupted by a virus. Run a Virus Scan
program and repair if possible. Contact Technical Support if the
Virus renders the software drivers not useable.
BUSY Indicator LED flashes
slowly
•
•
•
The disc may be dirty Clean it with a soft damp cloth. Avoid
cleaning the disc using a circular motion. The disc should be
wiped in a radial direction. That is, from the inner side outward.
The laser lens may have become cloudy or blocked by
particulate matter. Please contact Technical Support.
BUSY Indicator LED is
constantly ON
Possible Hardware Problem. Please contact Technical Support.
DVD-ROM can not play a DVD
in the drive or certain types of
CD media (i.e. CD-plus, etc.)
•
•
Is the CD-RW/DVD-ROM Combo drive driver loaded
Is the DVD disc the correct format for the type of system that you
are using? (i.e. on a PC an ISO9660 IBM compatible PC format
as opposed to Apple/Mac HFS disc or UNIX disc formats which
will not function).
•
•
Do you have the correct software applications program/drivers
installed to run a DVD disc?
Has the Windows CD-RW/DVD-ROM Combo drive software
driver program been corrupted by a virus. Run a Virus Scan
program and repair if possible. Contact Technical Support if the
Virus renders the software drivers not useable.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS –SD-R2612
General
Interface:
ATAPI
Format Compatibility
CD:
•
•
•
•
•
•
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data\
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
DVD
•
•
•
•
•
•
•
•
DVD DVD-ROM (Book 1.02)
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0) DVD RW DVD-RAM P
DVD+R (Version 1.0)
DVD RW
DVD-RAM
Note: All DVD/CD formats, except CD-Red Book (audio), require additional application specific software
and/or hardware. The drive is capable of reading these data formats. However, in order to run applications
that use these formats, you must first have the required software and/or hardware.
Data Disc Capacities
DVD-ROM
4.377GB (DVD-5)
7.959GB (DVD-9)
8.754GB (DVD-10)
15.917GB (DVD-18)
3.679GB
4.377GB
4.377GB
DVD-R (Ver 1)
DVD-R (Ver 2.0)
DVD-RAM (Ver 2.1)
CD
656.5MB (mode 1)
748.8MB (mode 2)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance
Transfer Rate
DVD (Single)
DVD (Dual)
DVD+/-R
DVD+/-RW
DVD-RAM (Ver 2.1)
CD-ROM/R (Read, Mode 1)
CD-RW Read (Mode 1)
10,800KB/second max (8X max)
8,100KB/second max (6X max)
8,100KB/second max (6X max)
8,100KB/second max (6X max)
5,400KB/second max (4X max)
3,600KB/second (24X max)
3,600KB/second (24X max)
Random Access Time
CD-ROM
CD-RW
DVD (single)
DVD (dual)
DVD-R/+R
DVD-RW/+RW
DVD-RAM
130ms
130ms
130ms
150ms
150ms
150ms
250ms
Data Error Rate
10-15 Max
DVD-ROM
CD-ROM
10-12 Max (Mode 1)
10-9 Max (Mode 2)
Data Buffer
2MB
Reliability
MTBF
80,000 hours
2,000 hours/year
42.6%
9.3%
31%
•
Power ON Hours
SEQ Read
Seek
Write
Power ON/OFF
Drawer Test
•
•
•
•
7.7%
9.3%
Drive Lifetime
Drawer Load/Release
5 years
10,000 times
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental
Ambient Temperature
Operating
5° to 50° C (41° to 122° F)
-40° to 65° C (-40° to 149° F)
Storage
Relative Humidity
Operating
10% to 90%
5% to 95% (wet bulb 40° C max)
Storage/Shipping
Vibration
Operating (5 to 500 Hz) (read)
Operating (5 to 500Hz) (write)
Non-operating (10 to 500Hz)
Packing (10 to 25 Hz)
2.45 m/s2 (0.25G) (O-P)
2.45 m/s2 (0.25G) (O-P)
9.8 m/s2 (1.0G) (O-P)
9.8 m/s2 (1.0G) (O-P)
Shock (Non-operating)
Acoustical Noise
490 m/s2 [50G]
40dB
Power
DC Voltage and Current Requirements
+5V 5% (Operating)
Physical
Height
Width
Depth
Weight
0.5" (12.7mm)
5.04" (128mm)
5.00" (127mm)
6.35oz (.18kg)
Connectors
IDE Interface Connector
50 Pin I/F ATAPI Standard
Regulatory
The SD-R2612 DVD Writeable drive has been certified by the following
regulatory agencies:
•
•
•
•
•
•
UL 1950
CSA C22.2 No. 950
TUV (EN60950I)
CE standard
DHHS 21 CFR Sub-Chapter J
FDA CFR21, EN60825
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Connectors –SD-R2612
Figure 1.SD-R2612 DVD Writeable Drive Rear Panel – Connector
A 50-pin ATAPI interface connector is found at the rear of the SD-R2612 CD-RW/DVD-
ROM Combo drive. Connecting cable should use Japan Aviation Electronics Industry
Limited KX14-50Series L or equivalent connector.
ATAPI
Connector
Table 1.Interface Pin Assignments
PIN
NO.
1
3
5
I/O SIGNAL NAME
PIN
NO.
2
4
6
I/O
SIGNAL NAME
O
Audio L-CH
Audio Ground
/RESET
O
Audio R-CH
Digital Ground
DD8
DD9
DD10
DD11
DD12
DD13
DD14
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
7
9
I/O DD7
I/O DD6
I/O DD5
I/O DD4
I/O DD3
I/O DD2
I/O DD1
I/O DD0
8
10
12
14
16
18
20
22
24
11
13
15
17
19
21
23
DD15
DMARQ
/DIOR: /
HDMARDT:
HSTROBE
Ground
/DMACK
Ground
I
25
27
I
O
/DIOW:STOP
IORDY: /
DDMARDY:
DSTROBE
INTRQ
26
28
I
29
31
33
35
37
39
41
43
45
47
49
O
I
30
32
34
36
38
40
42
44
46
48
50
O
I/O
/IOCS16
/PDIAG
DA2
DA1
I
DA0
I
I
I
I
I
I
/CS1FX
/CS3FX
I/O /DASP
+5V (Motor)
+5V (Motor)
+5V (Logic)
Ground
Ground
Ground
I
I
+5V (Motor)
+5V (Logic)
Ground
Ground
I
I
CSEL
Vendor Unique*
I
Vendor Unique*
*Vender Unique, don't connect pins
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|