Satellite P30 Series
TOSHIBA
Satellite P30 Series
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Macrovision License of Notice
This product incorporates copyright protection technology that is protected
by methods and claims of certain U.S. patents and other intellectual rights
owned by Macrovision Corporation, and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision
Corporation and is intended for home and other limited viewing uses only
unless authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Safety Instructions
Use the following safety guidelines to help protect yourself and your
computer.
When Using Your Computer
Do not operate your portable computer for an extended period of time with
the base resting directly on your body. With extended operation, heat can
potentially build up in the base. Allowing sustained contact with the skin
could cause discomfort or, eventually, a burn.
■ Do not attempt to service the computer yourself and always follow
installation instructions closely.
■ Do not carry a battery in your pocket, purse, or other container where
metal objects (such as car keys) could short-circuit the battery
terminals. The resulting excessive current flow can cause extremely
high temperatures and may result in damage from burns.
■ Be sure that nothing rests on your AC adapter's power cable and that
the cable is not located where it can be tripped over or stepped on.
■ Place the AC adapter in a ventilated area, such as a desk top or on the
floor, when you use it to run the computer or to charge the battery. Do
not cover the AC adapter with papers or other items that will reduce
cooling; also, do not use the AC adapter while it is inside a carrying
case.
■ Use only the AC adapter and batteries that are approved for use with
this computer. Use of another type of battery or AC adapter may risk
fire or explosion.
■ Before you connect the computer to a power source, ensure that the
voltage rating of the AC adapter matches that of the available power
source.
115 V/60Hz in most of North and South America and some Far Eastern
countries such as Taiwan.
100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan.
230 V/50 Hz in most of Europe, the Middle East, and the Far East.
■ If you use an extension cable with your AC adapter, ensure that the total
ampere rating of the products plugged in to it does not exceed the
ampere rating of the extension cable itself.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
■ To remove power from the computer, turn it off, remove the battery, and
disconnect the AC adapter from the electrical outlet.
■ To help avoid the potential hazard of electric shock, do not connect or
disconnect any cables or perform maintenance or reconfiguration of this
product during an electrical storm.
■ When setting up the computer for work, place it on a level surface.
■ Do not dispose of batteries in a fire as they may explode. Check with
local authorities for disposal instructions.
■ When traveling, do not check the computer as baggage. You can put
your computer through an X-Ray security machine, but never put your
computer through a metal detector. If you have the computer checked
by hand, be sure to have a charged battery available in case you are
asked to turn on the computer.
■ When traveling with the hard drive removed from the computer, wrap
the drive in a non-conducting material, such as cloth or paper. If you
have the drive checked by hand, be ready to install the drive in the
computer. Your can put the hard drive through an X-Ray security
machine, but never, but the drive through a metal detector.
■ When traveling, do not place the computer in overhead storage
compartments where it could slide around. Do not drop your computer
or subject it to other mechanical shocks.
■ Protect your computer, battery, and hard drive from environmental
hazards such as dirt, dust, food, liquids, temperature extremes, and
overexposure to sunlight.
■ When you move your computer between environments with very
different temperature and/or humidity ranges, condensation may form
on or within the computer. To avoid damaging the computer, allow
sufficient time for the moisture to evaporate before using the computer.
When taking the computer from low-temperature conditions into a warmer
environment or from high-temperature conditions into a cooler
environment, allow the computer time to acclimatise to room temperature
before turning on the power.
■ When you disconnect a cable, pull on its connector or on its strain relief
loop, not on the cable itself. As you pull out the connector, keep it
evenly aligned to avoid bending any connector pins. Also, before you
connect a cable make sure both connectors are correctly oriented and
aligned.
■ Before you clean your computer, turn if off, unplug it from its power
source, and remove the battery.
■ Handle components with care. Hold a component such as a memory
module by its edges, not its pins.
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
■ Do not use this product near water, for example, near a bathtub,
washing bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
■ Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
■ Do not use the telephone to report a gas leak in the vicinity of the leak.
■ Use only the power cord indicated in this manual.
■ Replace only with the same or equivalent type battery recommended by
the manufacturer.
■ Dispose of used batteries according to the manufacturer's instructions.
Use only the battery pack that came with the computer or an optional
battery pack. Use of the wrong battery could damage your computer.
TOSHIBA assumes no liability for any damage in such case.
FCC information
Model Name: Satellite P30
FCC notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer's or expansion unit's external monitor port, USB
port and microphone jack. Changes or modifications made to this
equipment, not expressly approved by TOSHIBA or parties authorized by
TOSHIBA could void the user's authority to operate the equipment.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
v
EMC Regulatory Information
Contact
Address:
TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone:
(949)583-3000
EU Declaration of Conformity
TOSHIBA declares, that the product: Satellite P30 conforms to the
following Standards:
Supplementary Information: "The product complies with the requirements
of the Low Voltage Directive 73/23/EEC and
the EMC Directive 89/336/EEC and/or the
R&TTE Directive 1999/05/EEC."
This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe,
Hammfelddamm 8, 41460 Neuss, Germany.
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by
TOSHIBA Corporation could void your authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouilleur du Canada.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
Optical Disc Drive Safety Instruction
■ Be sure to check the international precautions at the end of this
section.
The optical drive that is used in this computer is equipped with a laser
device. The classification label with the following sentence is affixed to the
surface of the drive.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT
The drive with the above label is certified by the manufacturer that the drive
complies with the requirement for laser product on the date of
manufacturing pursuant to article 21 of Code of Federal Regulations by the
United States of America, Department of Health & Human Services, Food
and Drug Administration.
In other countries, the drive is certified to comply with the requirement
pursant to IEC 825 and EN60825 on class 1 laser product.
This computer is equipped with one of the optical drives in the following list
according to the model.
Manufacturer
TOSHIBA Samsung
Matsushita
Matsushita
Matsushita
TEAC
Type
CD-RW/DVD-ROM SD-R2512
CD-RW/DVD-ROM UJDA760
DVD Super Multi UJ-831B
DVD Super Multi UJ-820B
CD-RW/DVD-ROM DW-224E
DVD Super Multi DV-W24E-0TT
CD-RW/DVD-ROM GCC-4243N
DVD Dual DVR-K13TBT
DVD Dual DVR-K14TBT
TEAC
HLDS
Pioneer
Pioneer
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
International precautions
■ This drive employs a laser system. To ensure proper use of this
product, please read this instruction manual carefully and retain for
future reference. Should the unit ever require maintenance, contact an
authorized service location.
■ Use of controls, adjustments or the performance of procedures other
than those specified may result in hazardous radiation exposure.
■ To prevent direct exposure to the laser beam, do not try to open the
enclosure.
Location of the required label
Sample shown below. Location of the label on the drive and manufacturing
information may vary.
CAUTION: This appliance contains a laser
system and is classified as a "CLASS 1 LASER
PRODUCT." To use this model properly, read the
instruction manual carefully and keep this manual
for your future reference. In case of any trouble
with this model, please contact your nearest
"AUTHORIZED service station." To prevent direct
exposure to the laser beam, do not try to open the
enclosure.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
VORSICHT: Dieses Gerät enthält ein Laser-
System und ist als "LASERSCHUTZKLASSE 1
PRODUKT" klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste "autorisierte
Service-Vertretung". Um einen direkten Kontakt
mit dem Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at apparatet
arbejder med laserstråler af klasse 1, hviket
betyder, at der anvendes laserstrlier af svageste
klasse, og at man ikke på apparatets yderside
kan bilve udsat for utilladellg kraftig stråling.
APPARATET BOR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer imod
at foretage sådanne indgreb i apparatet, at man
kan komme til at udsætte sig for laserstråling.
OBS! Apparaten innehåller laserkomponent som
avger laserstråining överstigande gränsen för
laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää näkymätöntä
silmilie vaarallista lasersäteilyä.
CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED IN THE OWNER'S MANUAL MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS DURCHFÜHREN
VON ANDEREN VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG BESCHRIEBEN
KÖNNEN GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR FOLGE
HABEN.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ix
Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision "CTR21"] for
pan- European single terminal connection to the Public Switched
Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.
In the event of problems, you should contact your equipment supplier in the
first instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to confirm with the additional
requirements conditional in EG 201 121.
Germany
ATAAB AN005,AN006,AN007,AN009,AN010
and DE03,04,05,08,09,12,14,17
Greece
ATAAB AN005,AN006 and GR01,02,03,04
Portugal
ATAAB AN001,005,006,007,011 and
P03,04,08,10
Spain
ATAAB AN005,007,012, and ES01
ATAAB AN002
Switzerland
All other countries/
regions
ATAAB AN003,004
Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.
Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in
the Telecommunications Business Law require that you select the Japan
country mode.
It is illegal to use the modem in Japan with any other selection.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Redial
Up to two redial attempts can be made. If more than two redial attempts are
made, the modem will return Black Listed. If you are experiencing problems
with the Black Listed code, set the interval between redials at one minute or
longer.
Japan's Telecommunications Business Law permits up to two redials on
analogue telephones, but the redials must be made within a total of three
minutes.
The internal modem is approved by Japan Approvals Institute for
Telecommunications Equipment.
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone
company and give them the following information:
■ The telephone number of the line to which you will connect the modem
■ The registration number that is located on the device
The FCC registration number of the modem will be found on either the
device which is to be installed, or, if already installed, on the bottom of the
computer outside of the main system label.
■ The Ringer Equivalence Number (REN) of the modem, which can vary.
For the REN of your modem, refer to your computer's user's guide.
The modem connects to the telephone line by means of a standard jack
called the USOCRJ11C.
Type of service
Your modem is designed to be used on standard-device telephone lines.
Connection to telephone company-provided coin service (central office
implemented systems) is prohibited. Connection to party lines service is
subject to state tariffs. If you have any questions about your telephone line,
such as how many pieces of equipment you can connect to it, the
telephone company will provide this information upon request.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it
can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations, or procedures. If these changes
might affect your service or the operation of your equipment, the telephone
company will give you notice in writing to allow you to make any changes
necessary to maintain uninterrupted service.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xi
If problems arise
If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to
the telephone network. If the telephone company notes a problem, they
may temporarily discontinue service. When practical, they will notify you in
advance of this disconnection.
If advance notice is not feasible, you will be notified as soon as possible.
When you are notified, you will be given the opportunity to correct the
problem and informed of your right to file a complaint with the FCC. In the
event repairs are ever needed on your modem, they should be performed
by TOSHIBA Corporation or an authorized representative of TOSHIBA
Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message
via a telephone fax machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of
the transmission, the date and time it is sent and an identification of the
business, other entity or individual sending the message and the telephone
number of the sending machine or such business, other entity or individual.
In order to program this information into your fax modem, you should
complete the setup of your fax software before sending messages.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xii
Instructions for IC CS-03 certified equipment
1. NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection.
The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician,
as appropriate.
2. The user manual of analog equipment must contain the equipment's
Ringer Equivalence Number (REN) and an explanation notice similar to
the following: The Ringer Equivalence Number (REN) of the modem,
which can vary. For the REN of your modem, refer to your computer's
user's guide.
The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.
3. The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
The IC registration number of the modem is shown below.
Canada: 1353-11026A
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xiii
Important Notice
Copyrighted works including, but not limited to music, video, computer
programs and databases are protected by copyright laws. Unless
specifically permitted under applicable copyright laws, you cannot copy,
modify, assign, transmit or otherwise dispose of any copyrighted work
without the consent of the owner of the copyright.
Please take notice that unauthorized copying, modification, assignment,
transmission and disposition may be subject to claims for damages and
penalties
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.
Be certain to read the general precautions below and to note the cautions
included in the text of the manual.
Stress injury
Carefully read the Safety Instruction Manual. It contains information on
prevention of stress injuries to your hands and wrists that can be caused by
information on work space design, posture and lighting that can help
reduce physical stress.
Heat warning
■ Avoid prolonged physical contact with the bottom of the computer. If the
computer is used for long periods, its surface can become very warm.
While the temperature will not feel hot to the touch, if you maintain
physical contact with the computer for a long time (if you rest the
computer on your lap, for example) your skin might suffer low-heat
injury.
■ If the computer has been used for a long time, avoid direct contact with
the metal plate supporting the I/O ports. It can become hot.
■ The surface of the AC adaptor can become hot when in use. This
condition does not indicate a malfunction. If you need to transport the
AC adaptor, disconnect it and let it cool before moving it.
■ Do not lay the AC adaptor on a material that is sensitive to heat. The
material could be damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can damage computer components or
otherwise cause malfunctions.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
PC Card overheating
Some PC Cards can become hot with prolonged use. If two cards are
installed, both can become hot even if only one is used extensively.
Overheating of a PC Card can result in errors or instability in the PC Card
operation. Also be careful when you remove a PC Card that has been used
for a long time.
Mobile phones
Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but it is recommended that a distance of 30cm be
maintained between the computer and a mobile phone in use.
Central Processing Unit (“CPU”) Performance Disclaimer:
CPU performance in your computer product may vary from specifications
under the following conditions:
■ use of certain external peripheral products
■ use of battery power instead of AC power
■ use of certain multimedia, computer generated graphics or video
applications
■ use of standard telephone lines or low speed network connections
■ use of complex modeling software, such as high end computer aided
design applications
■ use of several applications or functionalities simultaneously
■ use of the computer in areas with low air pressure (high altitude > 1,000
meters or > 3,280 feet above sea level)
■ use of the computer at temperatures outside the range of 5 ºC to 30 ºC
(41ºF to 86 ºF) or > 25 ºC (77 ºF) at high altitude (all temperature
references are approximate and may vary depending on the specific
computer model).
CPU performance may also vary from specifications due to design
configuration.
Under some conditions, your computer product may automatically shut-
down.
This is a normal protective feature designed to reduce the risk of lost data
or damage to the product when used outside recommended conditions.
To avoid risk of lost data, always make back-up copies of data by
periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions under “Environmental
Service and Support for more information.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xv
Satellite P30 Series
Table of Contents
Preface...........................................................................................xxii
Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17
Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Back side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Keyboard Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xvi
Table of Contents
Optical Media drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
DVDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Work habits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Turning off the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xvii
Table of Contents
Writing CD/DVDs on a DVD±R/±RW drive and a DVD±R/±RW
drive supporting Double Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Writing CD/DVDs on a DVD Super Multi drive and a DVD Super
Multi drive supporting Double Layer . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Data Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Diskettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
TV-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xviii
Table of Contents
Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Emulation keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Battery indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
DC IN indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Power indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Panel power off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xix
Table of Contents
PC cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
System start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Self test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
LCD panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Hard disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
Pointing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xx
Table of Contents
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19
TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Before you call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Where to write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
User’s Manual
xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite P30 Series
Preface
Congratulations on your purchase of the Satellite P30 computer. This
powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.
This manual tells how to set up and begin using your Satellite P30
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.
If you are a new user of computers or if you're new to portable computing,
first read over the Introduction and The Grand Tour chapters to familiarize
yourself with the computer's features, components and accessory devices.
Then read Getting Started for step-by-step instructions on setting up your
computer.
If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the
Special features section of the Introduction, to learn about features that are
uncommon or unique to the computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xxii
Manual contents
This manual has eight chapters, three appendixes and a Glossary.
utilities, and options.
briefly explains how they function.
operating your computer and gives tips on safety and designing your work
area. Be sure to read the sections on setting up the operating system and
on restoring the preinstalled software.
devices on the computer including the Touch pad, the optical media drive,
the internal modem, LAN and wireless LAN.
It also provides tips on care of the computer, diskettes and DVD/CD-ROMs.
the keypad overlay and hotkeys.
power resources.
some diagnostic tests, and suggests courses of action if the computer
doesn't seem to be working properly.
The Appendices provide technical information about your computer.
acronyms used in the text.
Conventions
This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.
User’s Manual
xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Keys
The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.
Key operation
Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, Ctrl + C means you must hold down Ctrl and at the same
time press C. If three keys are used, hold down the first two and at the
same time press the third.
DISKCOPY A: B:
When procedures require an action such as
clicking an icon or entering text, the icon's name
or the text you are to type in is represented in the
type face you see to the left.
Display
Names of windows or icons or text generated by
the computer that appears on its display screen
is presented in the type face you see to the left.
ABC
Messages
Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.
Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.
Please read. A note is a hint or advice that helps you make best use of
your equipment.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
xxiv
Satellite P30 Series
Chapter 1
Introduction
This chapter provides an equipment checklist, and it identifies the
computer's special features, options and accessories.
Basic features are described in a separate pamphlet.
Some of the features described in this manual may not function properly if
you use an operating system that was not preinstalled by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for
future use. Check to make sure you have all the following items:
Hardware
■ Satellite P30 Series Portable Personal Computer
■ Universal AC adaptor and power cord
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-1
Introduction
Software
■ The following software preinstalled on your hard disk:
®
®
■ Microsoft Windows XP
■ TOSHIBA Utilities
■ Display Driver
■ Touch pad driver
■ Sound driver
■ Miscellaneous drivers (depending on the model you purchased
these will include drivers for devices such as the modem, LAN,
wireless LAN and Multiple Digital Media Card Slot)
■ Online help
■ Product Recovery Disk
■ TOSHIBA Tools & Utilities CD-ROM
The system may not function properly if you use drivers that are not
preinstalled or distributed by TOSHIBA
Documentation
■ Your computer's documentation:
■ Satellite P30 User's Manual
■ Satellite P30 Quickstart
®
■ Microsoft Windows XP Getting Started booklet
■ Safety Instruction Manual
■ Warranty information
If any of the items are missing or damaged, contact your dealer
immediately.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
Introduction
Features
The Satellite P30 series computer uses TOSHIBA's advanced Large Scale
Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS)
technology extensively to provide compact size, minimum weight, low
power usage, and high reliability. This computer incorporates the following
features and benefits:
Processor
®
®
Intel Celeron Processor up to 2.8 GHz
®
®
Intel Celeron D Processor 325/330/335 or
higher
®
®
Mobile Intel Pentium 4 Processor 2.8GHz/
3.06GHz
®
®
Mobile Intel Pentium 4 Processor 2.8GHz/
3.06GHz/3.2GHz supporting Hyper-Threading
Technology
®
®
Mobile Intel Pentium 4 Processor 518/532/538
or higher, supporting Hyper-Threading
Technology
Chip Set
TM
TM
TM
ATI MOBILITY
RADEON 9000 IGP
TM
ATI MOBILITY
on models)
RADEON 9700 (depending
ATI IXP150
ENE KB910 for the keyboard controller, battery
management unit, and Real-Time Clock (RTC.
CB714 for Card Bus PCMCIA controller with
Multiple Digital Media Card Slot
ALC250 for AC97 CODEC.
VIA VT6301S for IEEE 1394 controller.
Realtek RTL8100CL for the onboard LAN.
User’s Manual
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Memory
Slot
Two DDR SODIMM sockets with support for
256MB/512MB/1GB modules
Two DDR SODIMM sockets with support for
256MB/512MB/1GB modules
®
®
L2 Cache
128KB L2 Cache (Intel Celeron Processor up
to 2.8GHz)
®
®
256KB L2 Cache (Intel Celeron D Processor
325/330/335 or higher)
®
®
512KB L2 Cache (Mobile Intel Pentium 4
Processor up to 3.2GHz)
®
®
1MB L2 Cache (Mobile Intel Pentium 4
Processor 518/532/538 or higher)
Video RAM
Up to 128MB memory for ATI MOBILITY™
RADEON™ 9000 IGP shared with main system
memory
External 64/128MB VGA DDR RAM for ATI
MOBILITY™ RADEON™ 9700
BIOS
1MB Flash ROM for system BIOS.
Suspend to RAM/disk.
Password protection (System power on).
Various hot key functions for system control.
Upgradable
Complete ACPI 1.0b function support
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4
Introduction
Power
Battery Pack
12-cell Li-Ion smart battery pack with
14.8V*6450mAh capacity or 8-cell Li-Ion smart
battery pack with 14.8V*4300mAh capacity
(depending on the model)
Approximately 12 hours or longer charging time
to 100% battery capacity (system on).
Approximately 4 hours charging time to 100%
battery capacity (system off)
Approximately 3 days discharge time in Standby
Mode for the 12-cell battery and 2 days for the 8-
cell battery.
Discharge time when the computer is switched
off is approximately 1 month.
RTC Battery
AC adaptor
The computer has an internal battery to backup
the Real Time Clock (RTC) and calender
functions. This battery will last for approximately
1 month when the computer is disconnected from
mains power.
The universal AC adaptor provides power to the
system and recharges the batteries when they
are low. It comes with a detachable power cord.
Floppy Diskette Drive Devices
External USB FDD
Touch pad
Display
A Touch pad and control buttons in the palm rest
enable control of the on-screen pointer.
17.0" TFT screen, 16 million colors with a
resolution of 1440 horizontal x 900 vertical pixels,
widescreen XGA
17.0" TFT screen, 16 million colors with a
resolution of 1680 horizontal x 1050 vertical
pixels, widescreen SXGA+
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-5
Introduction
Disks
Fixed hard disk
Either one 40GB/60GB/80GB/100GB or larger
capacity hard drive
Bus Master IDE
9.5m/m 2.5" HDD Support
Ultra DMA 100
CD-RW/DVD-ROM
drive
Some models are equipped with a full-size CD-
RW/DVD-ROM module that lets you record data
to rewritable CD-Rs and CD-RWs as well as run
either 12cm (4.72") or 8cm (3.15") CD/DVDs
without using an adaptor. It reads DVD-ROMs at
a maximum 8 speed and CD-ROMs at a
maximum 24 speed. It writes both CD-Rs and
CD-RWs at up to 24 speed. The drive supports
the following formats of media on a read-only
basis.
■ DVD-ROM
■ DVD-Video
■ DVD-RW
■ CD-Text
■ DVD-R
■ CD-DA
■ DVD-RAM
■ Photo CD (single/multi-session)
■ CD-ROM Mode1, Mode2
■ CD-ROMXA Mode2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-6
Introduction
DVD±R/±RW (DVD
Dual) drive
supporting Double
Layer
Some models are equipped with a full-size DVD
Dual module that lets you record data to
rewritable CD/DVDs as well as run either 12cm
(4.72") or 8cm (3.15") CD/DVDs without using an
adaptor. It reads DVD-ROMs at a maximum
8 speed and CD-ROMs at a maximum 24 speed.
It writes CD-Rs at up to 24 speed, CD-RWs at up
to 16 speed, DVD-Rs and DVD+Rs at a
maximum 8 speed, DVD-RWs and DVD+RWs at
a maximum 4 speed and DVD+Rs (Double
Layer) at a maximum 2.4 speed. This drive
supports the same formats as the CD-RW/DVD-
ROM drive plus the following:
■ DVD-ROM
■ DVD-Video
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ CD-DA
■ CD-Text
■ DVD+R (Double Layer)
■ Photo CD (single/multi-session)
■ CD-ROM Mode1, Mode2
■ CD-ROMXA Mode2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-7
Introduction
DVD±R/±RW (DVD
Dual) drive
Some models are equipped with a full-size DVD
Dual module that lets you record data to
rewritable CD/DVDs as well as run either 12cm
(4.72") or 8cm (3.15") CD/DVDs without using an
adaptor. It reads DVD-ROMs at a maximum 8
speed and CD-ROMs at a maximum 24 speed. It
writes CD-Rs at up to 16 speed, CD-RWs at a
maximum 10 speed, DVD-Rs and DVD+Rs at a
maximum 4 speed, and DVD-RWs and
DVD+RWs at a maximum 2 speed. This drive
supports the same formats as the CD-RW/
DVD-ROM drive plus the following:
■ DVD-ROM
■ DVD-Video
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ CD-DA
■ CD-Text
■ Photo CD (single/multi-session)
■ CD-ROM Mode1, Mode2
■ CD-ROMXA Mode2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-8
Introduction
DVD Super Multi
drive supporting
Double Layer
Some models are equipped with a full-size DVD
Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CD/DVDs without
using an adaptor. It reads DVD-ROMs at a
maximum 8 speed and CD-ROMs at a maximum
24 speed. It writes CD-Rs at up to 24 speed, CD-
RWs at up to 10 speed, DVD-Rs and DVD+Rs at
maximum 8 speed, DVD-RWs and DVD+RWs at
maximum 4 speed, DVD-RAM at maximum 3
speed and DVD+Rs (Double Layer) at maximum
2.4 speed . This drive supports the same formats
as the CD-RW/DVD-ROM drive plus the
following:
■ DVD-ROM
■ DVD-Video
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ DVD-RAM
■ DVD+R9 (Double Layer)
■ CD-R
■ CD-RW
■ CD-DA
■ CD-Text
■ Photo CD (single/multi-session)
■ CD-ROM Mode1, Mode2
■ CD-ROMXA Mode2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-9
Introduction
DVD Super Multi
drive
Some models are equipped with a full-size DVD
Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CD/DVDs without
using an adaptor. It reads DVD-ROMs at a
maximum 8 speed and CD-ROMs at a maximum
24 speed. It writes CD-Rs at up to 16 speed, CD-
RWs at up to 8 speed, DVD-Rs at maximum 4
speed, DVD-RWs and DVD-RAM at maximum 2
speed, and DVD+Rs and DVD+RWs at
maximum 2.4 speed. This drive supports the
same formats as the CD-RW/DVD-ROM drive
plus the following:
■ DVD-ROM
■ DVD-Video
■ DVD-R
■ DVD-RW
■ DVD+R
■ DVD+RW
■ CD-R
■ CD-RW
■ CD-DA
■ CD-Text
■ DVD-RAM
■ Photo CD (single/multi-session)
■ CD-ROM Mode1, Mode2
■ CD-ROMXA Mode2 (Form1, Form2)
■ Enhanced CD (CD-EXTRA)
Computers in this series can be configured with multiple types of optical
media drive. For more information on the optical media drives available,
talk to your dealer. More information on using the optical media drive can
be found in Chapter 4, Operating Basics.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-10
Introduction
Slots
PC Card
The computer is equipped with one Type II
PC Card slot
MODEM/LAN card
PC Card 8.0 Compliant, supports 3V and 5V
cards
Multiple Digital
Media Card (SD/
This slot lets you easily transfer data from
devices, such as digital cameras and Personal
MMC/SM/MS/MS Pro/ Digital Assistants, that use flash-memory.
xD)
You can use memory module in this slot
Ports (depending on configuration)
External monitor
15-pin analog VGA port supports VESA DDC2B
compatible functions.
Universal Serial Bus The computer has three Universal Serial Bus
(USB) ports that comply with the USB 2.0
standard, which enables data transfer speeds
more than 40 times faster than USB 1.1 (which
this computer also supports.) The USB drives
may be used to transfer data at Low, Full, and
High speeds
i.LINK (IEEE1394)
This port enables high-speed data transfer
directly from external devices such as digital
video cameras.
TV Out
The 4-pin S-Video port is compatible with the
PAL or NTSC TV standards, supporting
Macrovision 7.02 copy protection.
Multimedia
Sound system
The Windows sound system compatible sound
system provides internal speakers as well as
jacks for an external microphone and
headphones.
Direct CD Play
Let you use the computer's fixed optical media
drive as a stand-alone audio CD-player. You can
also use the buttons to control the computer's
DVD video player or MP3 files when the system
is on.
Headphone jack
Microphone jack
A standard 3.5mm headphone jack
A standard 3.5 mm mini microphone jack enables
connection of monaural microphone input.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-11
Introduction
Communications
Modem
An internal modem provides capability for data
and fax communication. It supports V.90 or V.92
depending on the region. The speed of data and
fax transfer depends on the analog telephone
line conditions. It has a modem jack for
connecting to a telephone line.
LAN
The computer has built-in support for Ethernet
LAN (10 Mbps, 10BASE-T) and Fast Ethernet
LAN (100 Mbps 100BASE-TX)
Wireless LAN
Some computers in this series are equipped with
a wireless LAN mini-PCI card that is compatible
with other LAN systems that support either the
802.11a/g or the 802.11g wireless
communications standards. It has a Frequency
Channel Selection (2.4 or 5 GHz) and allows
roaming over multiple channels.
Security
Boot-up password protection
Two level password architecture
Security Lock Slot
Receives an optional security lock in order to
anchor the computer to a desk or other large,
heavy object.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-12
Introduction
Special features
The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.
Hotkeys
Key combinations let you quickly modify the
system configuration directly from the keyboard
without running a system configuration program.
Display Automatic
Power off
This feature automatically cuts off power to the
internal display when there is no input from the
keyboard or pointing device for a time specified.
Power is restored when any key is pressed or
when there is input from a pointing device. You
can specify the time in the TOSHIBA Power
Saver utility.
HDD Automatic
Power off
This feature automatically cuts off power to the
hard disk drive when it is not accessed for a time
specified. Power is restored when the hard disk
is accessed. You can specify the time in the
TOSHIBA Power Saver utility.
System Automatic
This feature automatically places the system into
Standby/Hibernation either Standby Mode or Hibernation Mode when
there is no input or hardware access for a time
specified. You can specify the time and select
either System Standby or System Hibernate in
the TOSHIBA Power Saver utility.
Keypad Overlay
A ten-key pad is integrated into the keyboard.
Refer to the Keypad overlay section in Chapter 5,
The Keyboard, for instructions on using the
keypad overlay.
Power-on Password Two levels of password security are available:
supervisor and user. This feature prevents
unauthorized access to your computer.
Battery Save Mode
This feature lets you save battery power. You can
specify the level of power management used
within the TOSHIBA Power Saver utility.
Instant Security
A hotkey function blanks the screen providing
quick and easy data security.
Panel Power Off/On
This feature turns power to the computer off
when the display panel is closed and turns it back
on when the panel is opened. You can specify
the setting in the TOSHIBA Power Saver utility
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-13
Introduction
Low Battery
Automatic
Hibernation
When battery power is exhausted to the point
that computer operation cannot be continued, the
system automatically enters Hibernation Mode
and shuts down. You can activate this setting in
the TOSHIBA Power Saver utility.
Hibernation
This feature lets you turn off the power without
exiting from your software. The contents of main
memory are saved to the hard disk. When you
turn on the power again, you can continue
working right where you left off. Refer to the
Turning off the power section in Chapter 3,
Getting Started, for details.
Standby
In Standby Mode, power to the system remains
on, but the CPU and all other devices are placed
into a 'sleep' mode. When the computer is in
Standby Mode, the Power LED flashes amber.
The computer enters Standby Mode regardless
of the associated setting for Hibernate Mode.
Refer to the Turning off the power section in
■ Before switching the computer off into Standby Mode, be sure to save
your data.
■ Do not install or remove a memory module while the computer is in
Standby Mode. The computer or the module could be damaged.
■ Do not remove the battery pack while the computer is in Standby Mode.
Data in memory will be lost.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-14
Introduction
Utilities
This section describes the preinstalled utilities and gives advice on how to
start them. For details on specific operations, refer to each utility's online
manual, help files or readme files.
TOSHIBA Power
Saver
There are two ways to display the Windows XP
Control Panel. The default is Category View.
TOSHIBA Power Saver utility is under the
Performance and Maintenance item.
TOSHIBA Controls
This utility provides you with the ability to
configure the following two areas:
■ Buttons
There are 7 kinds of menu in the pull down menu
list for the Buttons option. The default value for
the CD/DVD button is 'CD/DVD'.
■ CD/DVD
■ TV out
■ Outlook Express
■ Disable button
■ TOSHIBA Console
■ Internet Explorer
■ Select your program
■ Media Apps
Set the mode for the Audio/Video controls. Select
the application for audio and video playback.
TOSHIBA Console
DVD Player
TOSHIBA Console is a graphical user interface
that provides easy access to help and services.
The DVD Video Player is used to play DVD-
Video. It has an on-screen interface and
functions. Click Start, point to All Programs, point
to InterVideo WinDVD5 then click Inter Video
WinDVD5.
Config Free
ConfigFree is a suite of utilities to allow easy
control of communication devices and network
connections. ConfigFree also allows you to find
communication problems and create profiles for
easy switching between different locations and
communication networks.
To start ConfigFree, click the Windows Start
Button, point to All Programs, point to TOSHIBA,
point to Networking and click ConfigFree.
User’s Manual
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
TOSHIBA Touch pad Pressing Fn+F9 in a Windows environment
On/Off Utility
enables or disables the Touch pad function.
When you press these hot keys, the current
setting will change and be displayed as an icon.
RecordNow! Basic
for TOSHIBA
You can create CD/DVDs in several formats
including audio CDs that can be played on a
standard stereo CD player and data CD/DVDs to
store the files and folders on your hard disk drive.
This software can be used on models fitted with
either a CD-RW/DVD-ROM drive, a DVD±R/±RW
drive or a DVD Super Multi drive.
DLA for TOSHIBA
DLA (Drive Letter Access) is the packet writing
software which provides the function to write files
and/or folders to DVD±RW or CD-RW media via
a drive letter like a floppy disk or other removable
disks.
TOSHIBA Touch and TOSHIBA Touch and Launch is a tool that allows
Launch
you to perform various tasks easily by using the
Touch pad. It is useful in the following conditions.
■ To open a file located on the desktop whose
icon is obscured by a window.
■ To open a page contained in the Internet
Explorer Favorites menu.
■ To display the list of currently open windows
and change the active window.
■ It also provides the following functions by
customizing the settings.
■ To open a file stored in a predefined folder.
■ To quickly launch your frequently used
applications which have been registered.
TOSHIBA Zooming
Utility
This utility allows you to enlarge or reduce the
icon size on the desktop or the application
window.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1-16
Introduction
Options
You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:
Memory Modules
Two memory modules can be installed in the
computer
The computer comes with at least one memory module pre-installed.
Use only PC2700 compatible DDR memory modules. See your TOSHIBA
dealer for details
Battery Pack
AC Adaptor
An additional battery pack can be purchased
from your TOSHIBA dealer. Use it as a spare to
increase your computer operating time.
If you use your computer at more than one site
frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.
USB FDD Kit
Lets you attach a floppy diskette device to your
computer by means of a USB cable.
User’s Manual
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite P30 Series
Chapter 2
The Grand Tour
This chapter identifies the various components of your computer. Become
familiar with each component before you operate the computer.
Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.
Front with the display closed
The following figure shows the computer front with its display panel in the
closed position.
DC-IN LED
Power LED
Battery LED
Display Latch
Front of the computer with display closed
DC-in LED
The DC-IN LED indicates the computer is
connected to the AC adapter and it is plugged
into an AC power source.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-1
The Grand Tour
Power LED
Battery LED
The Power LED flashes amber while the system
is in Standby mode. The LED turns off when the
computer is turned off or in hibernation mode. In
normal operating mode, the LED is green.
The Battery LED indicates the battery's current
charge/discharge status. It lights green when the
battery is fully charged. It lights amber while the
battery is being charged from the AC adapter. It
flashes amber when the battery capacity is low.
Left side
The following figure shows the computer left side
Optical Media Drive
Optical Media Drive LED
The left side of the computer
Optical Media Drive
The computer is configured with a full-size optical
media drive module that lets you run either 12 cm
(4.72") or 8 cm (3.15") discs without using an
adaptor. See the Drives section in this chapter for
technical specifications on each drive and
using the drive and caring for discs.
The Optical Disc Access LED will light when the
drive is accessed.
User’s Manual
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
Right side
The following figure shows the computer right side
PC Card Slot
i.Link port
Volume
control
Headphone
Jack
Wireless
Communication Switch
Multiple digital media
card slot
Universal Serial
Bus (USB) Port
Microphone Jack
Wireless LED
The right side of the computer
* Some models are not equipped with Wireless Communication Switch.
* i.LINK is provided with some models.
PC Card Slot
A PC Card slot can accommodate one 5 mm PC
Card (Type II). You can install any industry
standard PC Card such as a SCSI adaptor,
Ethernet adaptor or flash memory card.
Multiple Digital
Media Card Slot
This slot allows you easily transfer data from
devices, such as digital cameras and Personal
Digital Assistance, that use flash memory. You
can insert several kinds of memory module (SD/
MMC/SM/MS/MS Pro/xD) into this slot.
Universal Serial Bus The Universal Serial Bus (USB 2.0 and 1.1) port
(USB) Port
enables USB-equipped devices (such as
keyboards, mice, hard drives, scanners, and
printers).
i .LINK (IEEE1394)
Port
Connect an external device, such as a digital
video camera to this port for high-speed data
transfer. This only applies the i.LINK model of the
computer. This feature may not be present,
depending on your configuration.
Volume Control
Headphone Jack
Use this dial to adjust the volume of the stereo
speakers or headphones.
The Headphone Jack lets you connect stereo
headphones or other audio-output devices such
as external speakers. Connecting headphones or
other devices to this jack automatically disables
the internal speakers.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3
The Grand Tour
Microphone Jack
A standard 3.5 mm mini microphone jack enables
connection of a three conductive type mini-jack
for a monaural microphone.
Wireless
Communication
The Wireless Communication Switch turns on the
wireless networking transceiver. The Wireless
Communication LED next to Wireless
communication switch indicates that wireless
networking is turned on.
Back side
The following figure shows the computer back panel.
DC-IN 19V Jack
External Monitor Jack
Modem Jack
Security Lock
TV out
Universal Serial
Bus (USB) Port
LAN Jack
The back side of the computer
Security Lock
A security cabel attaches to this port. The
optional security cable anchors your computer to
a desk or other large object to deter theft.
DC-IN 19V Jack
The DC-IN socket is where you plug in the AC
adapter.
External Monitor
Port
This 15-pin port lets you connect an external
video display to the computer.
TV Out
Plug a 4-pin S- video cable into this connector for
output of NTSC or PAL signal.
Universal Serial Bus The Universal Serial Bus (USB 2.0 and 1.1) port
(USB) Port
enables USB-equipped devices (such as
keyboards, mice, hard drives, scanners, and
printers).
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4
The Grand Tour
LAN Jack
This jack lets you connect to a LAN. The adaptor
has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second,
100BASE-TX).
Modem Jack
In areas where an internal modem is installed as
standard equipment, there is a modem jack that
lets you use a modular cable to connect the
modem directly to a telephone line. The modem
is not supported in some marketing regions.
Underside
The following figure shows the underside of the computer. Make sure the
display is closed before turning over your computer.
Battery
Battery Latch
Battery Double Lock
Expansion Memory Socket
The bottom of the computer
Expansion Memory
Socket
Use this socket to install a memory module to
increase your computer's memory. Refer to the
Memory Expansion section in Chapter 7,
Battery
This is the battery pack, which powers the
computer when the AC adaptor is not connected.
For detailed information on the battery pack, refer
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-5
The Grand Tour
Battery Double Lock When you slide this latch to the position of lock,
the battery can not be released even you have
slid the battery latch.
Battery Latch
Slide this latch to remove the battery pack.
Front with the display open
The following figure shows the front of the computer with the display open.
To open the display, slide the display latch on the front of the display and lift
up. Position the display at a comfortable viewing angle
Display Screen
CD/DVD Button
Play/Pause
Stop/Eject
Next/Fast Forward
Previous/Rewind
Right Speaker
Power Button
Left Speaker
Touch pad
Control Buttons
Touch pad
The front with the display open
* Some models are not equipped with a CD/DVD button and CD/DVD play
control buttons.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6
The Grand Tour
Power Button
Press the power button to turn the computer's
power on and off. There is one LED inside of
power button. The power button will shinning
blue when the system is accessed.
Left and Right
Speakers
The audio speakers.
TouchPad
A pointer control device located in the center of
the palm rest is used to control the on-screen
pointer. Refer to the Using the TouchPad section
TouchPad Cotrol
Buttons
Control buttons below the TouchPad let you
select menu items or manipulate text and
graphics designated by the on-screen pointer.
Previous/Rewind
Next/Fast Forward
Skips back to previous tracks. If held down while
a song is playing, it fast rewinds through it. Refer
Skips forward to next tracks. If held down while a
song is playing, it fast forwards through it. Refer
Stop
Stops playing the CD, DVD or digital audio. Refer
Play/Pause
Press this button to begin playing an audio CD, a
DVD movie or digital audio files. This button also
acts as a Pause button. Refer to Chapter 4,
Operating Basics for details.
CD/DVD Button
When system is off, pressing this button will turn
on CD Playback mode.
Pressing this button again will turn off CD
Playback mode. When system is turned on,
pressing this button will launch Windows Media
Player or if pressing this button with DVD inside
will launch WinDVD.
If Random or Shuffle is selected in Windows Media Player, selecting Next
or Previous advances to a random selection.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7
The Grand Tour
Display Screen
The LCD displays high-contrast text and graphics
at up to 2048x1536 pixel. Refer to Appendix B,
Display Modes. When the computer operates on
the AC adaptor the display screen's image will be
somewhat brighter than when it operates on
battery power. The brightness level is intended to
save battery power.
To prolong the life of your display screen, use a screen saver when you're
not working the computer and it is idle.
System Status Indicators
The following figure shows the system indicator lights, which light when
various computer operations are in progress
HDD Drive LED
CD Playback Mode LED
HDD Drive LED
The Hard Drive LED indicates that the HDD is
being accessed. Every time your computer runs
a program, opens a file, or performs some other
function in which it must access the HDD, this
light goes on.
CD Playback Mode
LED
The indicator of CD Playback mode. The LED
Will be turned on when system in CD Playback
Mode.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8
The Grand Tour
Keyboard Indicators
Caps
Lock
Arrow Mode
Numeric Mode
Caps Lock
Arrow Mode
When the Arrow mode icon lights green, you can
use the keypad overlay (light gray labeled keys)
as cursor keys. Refer to the Keypad Overlay
Numeric Mode
You can use the keypad overlay (light gray
labeled keys) for numeric input when the
Numeric mode icon lights green. Refer to the
Caps Lock
The Caps Lock LED lights when you press the
Caps Lock key. When this light is on, pressing a
letter key on the keyboard produces an
uppercase (capital) letter.
Caps
Lock
User’s Manual
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
Optical Media drive
One of the following optical media drives is installed in the computer:
CD-RW/ DVD-ROM drive, DVD-ROM drive, DVD-R/-RW drive, DVD±R/
±RW drive, DVD Super Multi drive. An ATAPI interface controller is used for
CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an
indicator on the drive glows.
Region codes for DVD drives and media
CD-RW/DVD-ROM, DVD-ROM, DVD-R/-RW, DVD±R/±RW drive, DVD
Super Multi drive and media are manufactured according to the
specifications of six marketing regions. When you purchase DVD-Video,
make sure it matches your drive, otherwise it will not play properly.
Code
Region
1
2
3
4
Canada, United States
Japan, Europe, South Africa, Middle East
Southeast Asia, East Asia
Australia, New Zealand, Pacific Islands, Central
America, South America, Caribbean
5
6
Russia, Indian Subcontinent, Africa, North Korea,
Mongolia
China
Writable discs
This section describes the types of writable CD/DVD discs. Check the
specifications for your drive to for the type of discs it can write. Use Record
CDs
■ CD-R discs can be written only once. The recorded data cannot be
erased or changed.
■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4
multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write
speed of the ultra-speed CD-RW discs (Ultra-speed is CD-RW/
DVD-ROM drive only) is maximum 24-speed.
DVDs
■ DVD-R and DVD+R discs can be written only once. The recorded data
cannot be erased or changed.
-
■ DVD RW, DVD+RW and DVD-RAM discs can be recorded more than
once.
User’s Manual
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grand Tour
Formats
The drives support the following formats
■ DVD-ROM
■ DVD-Video
■ CD-DA
■ CD-Text
■ Photo CD™ (single/multi-
session
■ CD-ROM Mode 1, Mode 2
■ CD-ROM XA Mode 2 (Form1,
Form2)
■ Enhanced CD (CD-EXTRA)
■ CD-RW/DVD-ROM drive
The full- size CD-RW/DVD-ROM drive module lets you record data to
rewritable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/
DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the other
edge.
DVD read
CD read
8 speed (maximum)
24 speed (maximum)
CD-R write
CD-RW write
24 speed (maximum)
24 speed (maximum, ultra-speed media)
This drive can not use ultra-speed+ CD-RW media.
DVD±R/±RW (DVD Dual) drive supporting Double Layer
The full- size DVD±R/±RW drive module lets you record data to rewritable
CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.
The read speed is slower at the center of a disc and faster at the other
edge.
DVD read
8 speed (maximum)
8 speed (maximum)
4 speed (maximum)
8 speed (maximum)
4 speed (maximum)
24 speed (maximum)
24 speed (maximum)
DVD-R write
DVD-RW write
DVD+R write
DVD+RW write
CD read
CD-R write
DVD+R(DL) write 2.4 speed (maximum)
CD-RW write
16 speed (maximum, ultra-speed media)
This drive can not use discs that allow writing faster than 8 speed (DVD-R,
DVD+R with Single Layer), 4 speed(DVD-RW, DVD+RW), 2.4
speed(DVD+R with Double Layer), or ultra-speed+(CD-RW).
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-11
The Grand Tour
DVD±R/±RW (DVD Dual) drive
The full- size DVD±R/±RW drive module lets you record data to rewritable
CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.
The read speed is slower at the center of a disc and faster at the other
edge.
DVD read
8 speed (maximum)
DVD-R write
DVD-RW write
DVD+R write
DVD+RW write
CD read
4 speed (maximum)
2 speed (maximum)
4 speed (maximum)
2.4 speed (maximum)
24 speed (maximum)
16 speed (maximum)
10 speed (maximum, high-speed media)
CD-R write
CD-RW write
This drive can not use ultra-speed CD-RW medias and ultra-speed+
CD-RW medias.
DVD Super Multi drive supporting Double Layer
The full-siza DVD super multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12cm(4.72") or 8cm(3.15") CD/
DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the other
edge.
DVD read
8 speed (maximum)
DVD-R write
DVD-RW write
DVD+R write
DVD+RW write
DVD-RAM write
CD read
8 speed (maximum)
4 speed (maximum)
8 speed (maximum)
4 speed (maximum)
3 speed (maximum)
24 speed (maximum)
24 speed (maximum)
10 speed (maximum, ultra-speed media)
CD-R write
CD-RW write
DVD-R (DL) write 2.4 speed (maximum)
This drive can not use discs that allow writing faster than 8 speed(DVD-R,
DVD+R with Single Layer), 4 speed(DVD-RW, DVD+RW), 3
speed(DVD-RAM), 2.4 speed(DVD+R with Double Layer), or ultra-
speed+(CD-RW).
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12
The Grand Tour
DVD Super Multi drive
The full-siza DVD super multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12cm(4.72") or 8cm(3.15") CD/
DVDs without using an adaptor.
The read speed is slower at the center of a disc and faster at the other
edge.
DVD read
8 speed (maximum)
DVD-R write
DVD-RW write
DVD+R write
DVD+RW write
DVD-RAM write
CD read
4 speed (maximum)
2 speed (maximum)
2.4 speed (maximum)
2.4 speed (maximum)
2 speed (maximum)
24 speed (maximum)
16 speed (maximum)
8 speed (maximum, high-speed media)
CD-R write
CD-RW write
This drive can not use discs that allow writing faster than 8 or more
speed(DVD-R, DVD+R with Single Layer), 4 or more speed(DVD-RW,
DVD+RW), 3 speed(DVD-RAM), ultra-speed+(CD-RW), or ultra-
speed(CD-RW).
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-13
The Grand Tour
AC adaptor
The AC adaptor converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use the computer in almost any country/region.
To recharge the battery, simply connect the AC adaptor to a power source
The AC adaptor
Use of the wrong adaptor could damage your computer. TOSHIBA
assumes no liability for any damage in such case. The output rating for the
computer is 19 volts DC.
Please use only the AC Adapter supplied with the computer or an AC
adapter certified by TOSHIBA.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2-14
Satellite P30 Series
Chapter 3
Getting Started
This chapter provides basic information to get you started using your
computer. It covers the following topics:
■ Setting up your work space - for your health and safety
Be sure also to read Instruction Manual for Safety & Comfort. This guide,
which is included with the computer, explains product liability.
■ Connecting the AC adaptor
■ Opening the display
■ Turning on the power
■ Starting up for the first time
■ Turning off the power
■ Restarting the computer
■ Restoring the preinstalled software
All users should be sure to carefully read the section Starting up for the first
time, which describe actions to take when you turn on the power for the
first time.
Setting up your work space
Establishing a comfortable work site is important for you and your
computer. A poor work environment or stressful work habits can result in
discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. Proper ambient conditions should also be maintained for the
computer's operation. This section discusses the following topics:
■ General conditions
■ Placement of the computer and peripheral devices
■ Seating and posture
■ Lighting
■ Work habits
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-1
Getting Started
General conditions
In general, if you are comfortable, so is your computer, but read the
following to make sure your work site provides a proper environment.
■ TOSHIBA Power SaverMake sure there is adequate space around the
computer for proper ventilation.
■ Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
■ The temperature should be 5 to 30 degrees Centigrade (41 to 86
degrees Fahrenheit) and the relative humidity should be 20 to 80
percent.
■ Avoid areas where rapid or extreme changes in temperature or humidity
may occur.
■ Keep the computer free of dust, moisture, and exposure to direct
sunlight.
■ Keep the computer away from heat sources, such as electric heaters.
■ Do not use the computer near liquids or corrosive chemicals.
■ Some components in the computer, including data storage media, can
be damaged by magnets. Do not place the computer near magnetic
objects or bring magnetic objects close to the computer. Be careful of
objects, such as stereo speakers, that produce strong magnetic fields
during operation. Also, be careful with metal objects, such as bracelets,
which can be inadvertently magnetized.
■ Do not operate the computer in close proximity to a mobile phone.
■ Leave ample ventilation room for the fan. Ensure that there are no
obstructions around any of the system inlets or exhaust vents.
Placement of computer
Position the computer and peripheral devices to provide comfort and safety.
■ Set the computer on a flat surface at a comfortable height and distance.
The display should be no higher than eye level to avoid eye strain.
■ Place the computer so that it is directly in front of you when you work
and make sure you have adequate space to easily operate other
devices.
■ Allow adequate space behind the computer to let you freely adjust the
display. The display should be angled to reduce glare and maximize
visibility.
■ If you use a paper holder, set it at about the same height and distance
as the computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2
Getting Started
Seating and posture
The height of your chair in relation to the computer and keyboard as well as
the support it gives your body are primary factors in reducing work strain.
Refer to the following tips and to figure.
90
1
Posture and positioning of the computer
■ Place your chair so that the keyboard is at or slightly below the level of
your elbow. You should be able to type comfortably with your shoulders
relaxed.
■ Your knees should be slightly higher than your hips. If necessary, use a
foot rest to raise the level of your knees to ease pressure on the back of
your thighs.
■ Adjust the back of your chair so it supports the lower curve of your
spine.
■ Sit straight so that your knees, hips and elbows form approximately 90
degree angles when you work. Do not slump forward or lean back too
far.
Lighting
Proper lighting can improve legibility of the display and reduce eye strain.
■ Position the computer so that sunlight or bright indoor lighting does not
reflect off the screen. Use tinted windows, shades or other screen to
eliminate sun glare.
■ Avoid placing the computer in front of bright light that could shine
directly in your eyes.
■ If possible, use soft, indirect lighting in your computer work area. Use a
lamp to illuminate your documents or desk, but be sure to position the
lamp so that it does not reflect off the display or shine in your eyes.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3
Getting Started
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your
activities.
If possible, schedule a variety of tasks into your work day. If you must
spend long periods at the computer, finding ways to break up the routine
can reduce stress and improve your efficiency.
■ Sit in a relaxed posture. Good positioning of your chair and equipment
as described earlier can reduce tension in your shoulders or neck and
ease back strain.
■ Vary your posture frequently.
■ Occasionally stand up and stretch or exercise briefly.
■ Exercise and stretch your wrists and hands a number of times during
the day.
■ Frequently, look away from the computer and focus your eyes on a
distant object for several seconds, for example 30 seconds every 15
minutes.
■ Take frequent short breaks instead of one or two long breaks, for
example, two or three minutes every half hour.
■ Have your eyes examined regularly and visit a doctor promptly, if you
suspect you might be suffering from a repetitive strain injury.
■ Please check every couple of months to ensure the fan inlets or
exhaust vents (see sections 2-5 and 2-7) are unobstructed. Clean them
if necessary.
A number of books are available on ergonomics and repetitive strain injury
or repetitive stress syndrome. For more information on these topics or for
pointers on exercises for such stress points as hands and wrists, please
check with your library or book vendor. Also refer to the computer's Safety
Instruction Manual.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4
Getting Started
Connecting the AC adaptor
Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power. The AC adaptor can be connected to any power source
supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the
Use of the wrong adaptor could damage your computer. TOSHIBA
assumes no liability for any damage in such case. The output rating for the
computer is 19 volts DC.
1. Connect the power cord to the AC adaptor.
Connecting the power cord to the AC adaptor
2. Connect the AC adaptor to the DC output plug to the DC IN input port
on the back of the computer.
Connecting the adaptor to the computer
3. Plug the power cord into alive wall outlet. The Battery and DC IN
indicators on the front of the computer should glow.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5
Getting Started
Opening the display
The display panel can be rotated in a wide range of angles for optimal
viewing.
1. Slide the display latch on the front of the computer to the right to unlatch
the display panel.
d
e
ReW
pe
S
ritable
h
g
i
H
Opening the display
2. Lift the panel up and adjust it to the best viewing angle for you.
Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6
Getting Started
Turning on the power
This section describes how to turn on the power.
After you turn on the power for the first time, do not turn it off until you have
set up the operating system. Refer to the section Starting up for the first
time in this chapter.
1. Make sure the diskette drive(optional) is empty. If a diskette is in the
drive, press the eject button and remove the diskette.
2. Open the display panel.
3. Press the computer's power button and release.
Turning on the power
Starting up for the first time
When you first turn on the power, the computer's initial screen is the
®
Microsoft Windows XP Startup Screen Logo. Follow the on-screen
directions for each screen. During setup, you can click the Back button to
return to the previous screen.
Be sure to read the Windows End User License Agreement display
carefully.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-7
Getting Started
Turning off the power
The power can be turned off in one of the following modes: Shut down
(Boot), Hibernation or Standby mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system's main screen.
1. If you have entered data, save it to the hard disk or to a diskette.
2. Make sure all disk activity has stopped, then remove the CD/DVD-ROM
or diskette.
Make sure the Built-in HDD and optical media drive are off. If you turn
off the power while a disk is being accessed, you can lose data or damage
the disk.
3. Click start and click Turn Off Computer. From the Turn Off Computer
window click Turn Off.
4. Turn off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk
when the computer is turned off. The next time the computer is turned on,
the previous state is restored. The hibernation feature does not save the
status of peripheral devices.
1. While entering hibernation mode, the computer saves the contents of
memory to the HDD. Data will be lost if you remove the battery or
disconnect the AC adaptor before the save is completed. Wait for the
Built-in HDD indicator to go out.
2. Do not install or remove a memory module while the computer is in
hibernation mode. Data will be lost.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8
Getting Started
Benefits of Hibernation
The hibernation feature provides the following benefits:
■ Saves data to the hard disk when the computer automatically shuts
down because of a low battery.
For the computer to shut down in hibernation mode, the hibernation feature
must be enabled in two places in TOSHIBA Power Saver: the Power Save
Modes tab and the Advanced tab. Otherwise, the computer will shut down
in Standby mode. If battery power becomes depleted, data saved in
Standby will be lost.
■ You can return to your previous working environment immediately when
you turn on the computer.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System
hibernate feature.
■ You can use the panel power off feature.
Starting Hibernation
You can also enable Hibernation by pressing Fn + F4. See Chapter 5, The
Keyboard, for details.
To enter Hibernation mode, follow the steps below.
1. Click Start.
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernate is not displayed.
4. Press the Shift key. The Standby item will change to Hibernate.
5. Select Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.
1. Open the Control Panel.
2. Open Performance and Maintenance and open Power Options.
3. Select the Hibernation tab.
4. Select Enable hibernate, then click OK button.
5. Open Toshiba Power Saver.
6. Select Setup Action tab.
7. Enable the desired Hibernation settings for When I press the power
button and When I close the lid of my portable computer.
8. Click the OK button.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-9
Getting Started
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a
moment to save current memory data to the hard disk. During this time, the
Built-in HDD indicator will light.
After you turn off the computer and memory is saved to the hard disk, turn
off the power to any peripheral devices.
Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.
Standby mode
In standby mode the power remains on, but the CPU and all other devices
are in sleep mode.
■ If the computer is not used or accessed in any way, including receipt of
e-mail, for 15 or 30 minutes when the AC adaptor is connected, the
computer will automatically enter Standby mode (TOSHIBA Power
Saver default).
■ To restore operation, press the power button.
■ If a network application is active when the computer automatically
enters Standby, it might not be restored when the computer wakes up
from standby. To prevent the computer from automatically entering
standby mode, disable Standby in the TOSHIBA Power Saver. Open
the TOSHIBA Power Saver and click the Power Save Modes tab. Next
select either an AC Power or Battery Power option and then click
details. When the details page comes up, you can disable the Standy
setting be moving the slider to Never. That action, however, will nullify
the computer's Energy Star compliance.
Standby precautions
■ Before entering Standby mode, be sure to save your data.
■ Do not remove/install memory or remove power components:
■ Do not remove/install the memory module. The computer or the
module could be damaged.
■ Do not remove the Battery Pack.
In any of the above cases, the standby configuration will not be saved.
■ If you carry the computer on board an aircraft or into a hospital, be sure
to shut down the computer in hibernation mode or in shutdown mode to
avoid radio signal interference.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Getting Started
Benefits of standby
The standby feature provides the following benefits:
■ Restores the previous working environment more rapidly than does
hibernation.
■ Saves power by shutting down the system when the computer receives
no input or hardware access for the duration set by the System Standby
feature.
■ You can use the panel power off feature.
Executing standby
Keyboard, for details.
You can enter standby mode in one of three ways:
1. Click start, click Turn Off Computer and click Stand by.
2. Close the display panel. This feature must be enabled. To enable it,
select the TOSHIBA Power Saver icon in the Control Panel and select
the Advanced tab and then set your When I close the lid options to
Standby.
3. Press the power button. This feature must be enabled. To enable it,
select the TOSHIBA Power Saver icon in the Control Panel and select
the Advanced tab.
When you turn the power back on, you can continue where you left when
you shut down the computer.
■ When the computer is shut down in standby mode, the power indicator
glows amber.
■ If you are operating the computer on battery power, you can lengthen
the operating time by shutting down in hibernation mode. Standby
mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
■ Power is turned back on immediately after shutting down.
■ Memory circuits are exposed to static electricity or electrical noise.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-11
Getting Started
Restarting the computer
Certain conditions require that you reset the system. For example, if:
■ You change certain computer settings.
■ An error occurs and the computer does not respond to your keyboard
commands.
There are three ways to reset the computer system:
1. Select Restart from the Turn Off Computer window in the start box.
2. If the computer is already on, press Ctrl + Alt + Del.
3. Press the power button to turn the computer off, then press it a second
to time in order to restart.
Only use step 3 if the operating system freezes or locks up due to a crash.
Performing step 3 should only ever be a last resort as you will lose all
unsaved data and could potentially damage critical files.
Restoring the preinstalled software
If preinstalled files are damaged, use the Product Recovery Media or the
TOSHIBA Tools & Utilities CD-ROM to restore them. To restore the
operating system and all preinstalled software, follow the steps below.
When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.
1. Load the Product Recovery Disk in the drive and turn off the computer's
power.
2. Power on your computer, when In Touch with Tomorrow TOSHIBA
appears, press F12 key. Boot Menu will appear.
3. Use the up or down cursor key to select the CD-ROM/DVD drive in the
display menu.
4. Follow the on-screen instructions.
Restoring TOSHIBA utilities and drivers
If Windows is working properly, individual drivers or applications can be
separately restored. The Toshiba Tools & Utilities CD-ROM contains drivers
and applications which were included with your computer system. If your
system drivers or applications have become damaged in some way, this
CD allows you to reinstall most of the components which are not part of the
Windows operating system.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3-12
Satellite P30 Series
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the
Touch pad, optical media drives, the internal modem, LAN, wireless LAN. It
also provides tips on caring for your computer and on heat dispersal.
Using the Touch pad
To use the Touch pad, simply move your finger tip across it in the direction
you want the on-screen pointer to go.
Touch pad Control Buttons
Touch pad
Touch pad and control buttons
Two buttons below the keyboard are used like the buttons on a mouse
pointer.
Press the left button to select a menu item or to manipulate text or graphics
designated by the pointer. Press the right button to display a menu or other
function depending on the software you are using.
Do not press on the Touch pad too hard or press a sharp object such as a
ball point pen against the Touch pad. The Touch pad could be damaged.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1
Operating Basics
The Touch pad has similar functions to a two-button mouse with a scroll
wheel. For some functions, you can tap the Touch pad instead of pressing a
control button.
You can customize pointing device actions in Mouse Properties. Open the
Control Panel, select the Mouse icon and press Enter to open the Mouse
Properties window.
Click
Click the left control button or tap the Touch pad one
time.
Double-click
Click the left control button twice or tap the Touch pad
twice.
Scroll
Vertical:
Move your finger up or down the right edge of the Touch
pad.
Horizontal:
Move your finger left or right along the bottom edge of
the Touch pad.
Using optical media drives
The illustrations in this section might differ slightly from your drive, but
operation is the same for all optical media drives. The full-size drive
provides high-performance execution of CD/DVD-ROM-based programs.
You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an
adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
When the computer is accessing a CD/DVD, an indicator on the drive
glows.
Use the WinDVD 5 application to view DVD-Video discs.
If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs on
CD-RW/DVD-ROM drive section for precautions on writing to CDs.
If you have a DVD±R/±RW drive, refer also to the Writing CD/DVDs on
DVD±R/±RW drive section for precautions on writing to CDs.
If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on
DVD Super Multi drive section for precautions on writing to CDs.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
Operating Basics
Loading optical media discs
To load a DVD/CD, follow the steps below and refer the following figures.
1. Turn on the power.
2. a. Press the eject button to open the drawer slightly.
Pressing the eject button
b. Pressing the eject button will not open the drawer when the
computer's power is off. If the power is off, you can open the drawer
by inserting a slender object (about 15 mm) such as a straightened
paper clip into the eject hole just to the right of the eject button.
Manual release with the eject hole
3. Grasp the drawer gently and pull until it is fully opened.
e
S
e
rtl
g
Pulling the drawer open
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3
Operating Basics
4. Lay the DVD/CD, label side up, in the drawer.
Inserting a DVD/CD
Be careful not to touch the lens or the area around it. Doing so could cause
the drive to malfunction.
5. Press gently at the center of the DVD/CD until you feel it click into
place. The DVD/CD should lie below the top of the spindle, flush with its
base.
6. Push the center of the drawer to close it. Press gently until it locks in
place.
If the DVD/CD is not seated properly when the drawer is closed, it might be
damaged. Also, the drawer might not open fully when you press the eject
button.
d
e
S
R
h
r
i
Closing the DVD-ROM drawer
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4
Operating Basics
Removing optical media discs
To remove the DVD/CD, follow the steps below and refer the following
figure.
Do not press the eject button while the computer is accessing the DVD
drive. Wait for the Diskette/Optical Media indicator to go out before you
open the drawer. Also, if the disc is spinning when you open it, wait for it to
stop before you remove it.
1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.
■ When the drawer pops open slightly, wait a moment to make sure the
DVD/CD has stopped spinning before pulling the drawer fully open.
■ Turn off the power before you use the eject hole. If the DVD/CD is
spinning when you open the drawer, it could fly off the spindlend cause
injury.
2. The DVD/CD extends slightly over the sides of the drawer so you can
grasp it. Hold the it gently and lift it out.
Removing a DVD/CD
3. Push the center of the drawer to close it. Press gently until it locks into
place.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5
Operating Basics
CD/DVD Button
The CD/DVD button can be defined upon user's preference. Once the
button has been defined, activate this button will launch the application
defined. If without specific definition it will launch CD/DVD only.
Press CD/DVD or play buttons when the computer system power is off. If
an audio CD is in the drive, the system enters CD playback mode and
operates as a stand-alone CD player.
CD/DVD play control buttons
In addition to the power button, the following four buttons control functions
of the optical media drive and Digital Audio Data:
Play/Pause
Stop
Starts or pauses play.
Stops play.
Next
Advances to the next track, chapter or data
Returns to the previous track, chapter or data
Previous
If Random or Shuffle is selected in Windows Media Player, selecting Next
or Previous advances to a random selection.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-6
Operating Basics
Writing CDs on a CD-RW/DVD-ROM drive
You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs.
The following applications for writing are preinstalled:
Record Now!/DLA, licensed by Sonic Solutions.
Important message
Before you write or rewrite to CD-R/RW disc, read and follow all setup and
operating instructions in this section. If you fail to do so, the CD-RW/
DVD-ROM drive may not function properly, and you may fail to write or
rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW disc that may be
caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/
-RW/ +R/+RW disc that may be caused by writing or rewriting with this
product, or for any business profit loss or business interruption that may
be caused by the change or loss of the recorded contents.
■ Damage that may be caused by using third party equipment or
software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.
CD-R discs can be written to only once. CD-RW discs can be rewritten
many times.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-7
Operating Basics
Before writing or rewriting
Please observe the following points when you write or rewrite the data.
■ We recommend the following manufacturers of CD-R and CD-RW
media. Media quality can affect write or rewrite success rates.
CD-R:
TAIYOYUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.
■ CD-RW can generally be rewritten about 1,000 times. However, the
actual number of rewrites is affected by the quality of the media and the
way it is used.
■ Be sure to connect the universal AC adaptor when you write or rewrite.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver which can put a heavy load
on the CPU.
■ Operate the computer at full power. Do not use power-saving features.
■ Do not write while virus check software is running. Wait for it to finish,
then disable virus detection programs including any software that
checks files automatically in the background.
■ Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and damage data.
■ Write from the computer's HDD to the CD. Do not try to write from
shared devices such as a LAN server or any other network device.
■ Writing with software other than Sonic RecordNow! has not been
confirmed. Therefore, operation with other software cannot be
guaranteed.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-8
Operating Basics
Writing CD/DVDs on a DVD±R/±RW drive and a DVD±R/
±RW drive supporting Double Layer
You can use the DVD±R/±RW drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW discs. The following applications for writing are
preinstalled:
Record Now!/DLA, licensed by Sonic Solutions. InterVideo WinDVD
Creator 2 Platinum, which is a product of InterVideo, Inc.
Important message
Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW disc, read
and follow all setup and operating instructions in this section. If you fail to
do so, the DVD±R/±RW drive may not function properly, and you may fail to
write or rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW disc that may be
caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/
-RW/ +R/+RW disc that may be caused by writing or rewriting with
thisproduct, or for any business profit loss or business interruption that
may be caused by the change or loss of the recorded contents.
■ Damage that may be caused by using third party equipment or
software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-9
Operating Basics
Before writing or rewriting
Please observe the following points when you write or rewrite data.
■ Based on TOSHIBA's limited compatibility testing, we suggest the
following manufacturers of CD-R/RW or DVD-R/-RW/+R/+RW disc.
However, in no event does TOSHIBA guarantee the operation, quality
or performance of any disc. Disc quality can affect write or rewrite
success rates.
CD-R:
TAIYOYUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW:
DVD-R:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD Specifications for Recordable Disc for
General Version 2.0
TAIYOYUDEN CO., LTD.
PIONEER VIDEO CORPORATION
MITSUBISHI CHEMICAL CORPORATION
DVD-RW:
DVD Specifications for Re-Recordable Disc for
Version 1.0 or Version 1.1, Version 1.2 (only for
DVD±R/±RW drive supporting Double Layer)
VICTOR COMPANY OF JAPAN, LIMITED
TDK Corporation
DVD+R:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD+RW:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD+R (Double
Layer)
MITSUBISHI CHEMICAL CORPORATION, only for
DVD±R/±RW drive supporting Double Layer
■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors
may occur. Be careful to check the disc for dirt or damage before you
use it.
■ The actual number of rewrites to CD-RW or DVD-RW/+RW is affected
by the quality of the disc and the way it is used.
■ There are two types of DVD-R: authoring and general use discs. Do not
use authoring discs. Only general use discs can be written to by a
computer drive.
■ Other DVD-ROM drives for computers or other DVD players may not be
able to read DVD-R/+R/-RW/+RW discs.
■ Data written to a CD-R/DVD-R/+R disc cannot be deleted either in
whole or in part.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-10
Operating Basics
■ Data deleted (erased) from a CD-RW and DVD-RW/+RW disc cannot
be recovered. Check the content of the disc carefully before you delete
it. If multiple drives that can write data to discs are connected, be
careful not to delete data from the wrong drive.
■ In writing to a DVD-R/+R/-RW/+RW disc, some disc space is required
for file management, so you may not be able to write the full capacity of
the disc.
■ Since the disc is based on the DVD-R/-RW standard, it will be filled with
dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.
■ Two types of DVD-R/+R/-RW/+RW discs are on the market: data and
video. Use a video disc to store video data. You can use video discs on
a DVD recorder as well as on your computer's DVD-ROM drive. You
cannot use data discs on a DVD recorder..
■ When multiple drives that can write data to discs are connected, be
careful not to write to the wrong drive.
■ Be sure to connect the universal AC adaptor before you write or rewrite.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver, which can put a heavy load
on the CPU.
■ Operate the computer in the full-power mode. Do not use power-saving
features.
■ Do not write while virus check software is running. Wait for it to finish,
then disable virus detection programs including any software that
checks files automatically in the background.
■ Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
■ Write from the computer's HDD to the CD/DVD. Do not try to write from
shared devices such as a LAN server or any other network device.
■ Writing with software other than Sonic RecordNow! has not been
confirmed. Therefore, operation with other software cannot be
guaranteed."
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-11
Operating Basics
Writing CD/DVDs on a DVD Super Multi drive and a
DVD Super Multi drive supporting Double Layer
You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
preinstalled:
Record Now!/DLA, licensed by Sonic Solutions.. InterVideo WinDVD
Creator 2 Platinum, which is a product of InterVideo, Inc..
Important message
Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
disc, read and follow all set-up and operating instructions in this section. If
you fail to do so, the DVD Super Multi drive may not function properly, and
you may fail to write or rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may
be caused by writing or rewriting with this product.
■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/
-RW/ +R/+RW /-RAM disc that may be caused by writing or rewriting
with this product, or for any business profit loss or business interruption
that may be caused by the change or loss of the recorded contents.
■ Damage that may be caused by using third party equipment or
software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-12
Operating Basics
Before writing or rewriting
Please observe the following points when you write or rewrite data.
■ Based on TOSHIBA's limited compatibility testing, we suggest the
following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
disc. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.
CD-R:
TAIYOYUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.
CD-RW:
DVD-R:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
DVD Specifications for Recordable Disc for
General Version 2.0
TAIYOYUDEN CO., LTD.
PIONEER VIDEO CORPORATION
MITSUBISHI CHEMICAL CORPORATION
DVD-RW:
DVD Specifications for Re-Recordable Disc for
Version 1.0 or Version 1.1, Version 1.2(only for
DVD Super Multi drive supporting Double
Layer)
VICTOR COMPANY OF JAPAN, LIMITED
TDK Corporation
DVD+R:
DVD+RW:
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
*DVD-RAM:
DVD Specifications for DVD-RAM Disc for
Version 2.0 or Version 2.1
Matsushita Electric Industrial Co., Ltd.
*DVD Multi drive and DVD Super Multi can use
DVD-RAM.
DVD+R (Double
Layer)
MITSUBISHI CHEMICAL CORPORATION, only for
DVD Super Multi drive supporting Double Layer
■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors
may occur. Be careful to check the disc for dirt or dama ge before you
use it.
■ The actual number of rewrites to CD-RW or DVD-RW/+RW/-RAM is
affected by the quality of the disc and the way it is used.
■ There are two types of DVD-R: authoring and general use discs. Do not
use authoring discs. Only general use discs can be written to by a
computer drive.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-13
Operating Basics
■ You can use DVD-RAM discs that can be removed from a cartridge and
DVD-RAM discs designed without a cartridge. You cannot use a disc
with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity.
■ Other DVD-ROM drives for computers or other DVD players may not be
able to read DVD-R/+R/-RW/+RW/-RAM discs.
■ Data written to a CD-R/DVD-R/+R disc cannot be deleted either in
whole or in part.
■ Data deleted (erased) from a CD-RW and DVD-RW/+RW/-RAM disc
cannot be recovered. Check the content of the disc carefully before you
delete it. If multiple drives that can write data to discs are connected, be
careful not to delete data from the wrong drive.
■ In writing to a DVD-R/+R/-RW/+RW disc, some disc space is required
for file management, so you may not be able to write the full capacity of
the disc.
■ Since the disc is based on the DVD-R/-RW standard, it will be filled with
dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.
■ Two types of DVD-R/+R/-RW/+RW/-RAM discs are on the market: data
and video. Use a video disc to store video data. You can use video
discs on a DVD recorder as well as on your computer's DVD-ROM
drive. You cannot use data discs on a DVD recorder.
■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000
without DVD-RAM Driver Software.
■ When multiple drives that can write data to discs are connected, be
careful not to write to the wrong drive.
■ Be sure to connect the universal AC adaptor before you write or rewrite.
■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM
writing. Writing is finished if you can eject DVD-RAM media.
■ Be sure to close all other software programs except the writing
software.
■ Do not run software such as a screen saver, which can put a heavy load
on the CPU.
■ Operate the computer in the full-power mode. Do not use power-saving
features.
■ Do not write while virus check software is running. Wait for it to finish,
then disable virus detection programs including any software that
checks files automatically in the background.
■ Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
■ Write from the computer's HDD to the CD/DVD. Do not try to write from
shared devices such as a LAN server or any other network device.
■ Writing with software other than Sonic RecordNow! has not been
confirmed. Therefore, operation with other software cannot be
guaranteed.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-14
Operating Basics
RecordNow! Basic for TOSHIBA
Note the following limitations when you use RecordNow!:
■ DVD-Video cannot be created using RecordNow!.
■ DVD-Audio cannot be created using RecordNow!.
■ You cannot use RecordNow!'s "Audio CD for Car or Home CD Player"
function to record music to the DVD-R/-RW or DVD+R/+RW disc.
■ Do not use the "Exact Copy"function of RecordNow! to copy DVD-
Video and DVD-ROM with copyright protection.
■ DVD-RAM disc cannot be backed up with the "Exact Copy"function of
RecordNow!.
■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/
+RW using the"Exact Copy"function of RecordNow!.
■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/
+RW to CD-R/RW using the RecordNow!
■ RecordNow! cannot record in packet format.
■ You might not be able to use the "Exact Copy"function of RecordNow!
to backup a DVD-R/-RW or DVD+R/+RW disc that was made with other
software on adifferent DVD-R/-RW or DVD+R/+RW recorder.
■ If you add data to a DVD-R and DVD+R disc that you have already
recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows ME. In Windows NT4, you will need
Service Pack 6 or later to read added data. In Windows 2000, you will
need Service Pack 2 or later to read it. Some DVD-ROM and
DVD-ROM&CD-R/RW drives cannot read added data regardless of the
operating system.
■ RecordNow! does not support recording to DVD-RAM discs. To record
to a DVD-RAM, use Explorer or other utility.
■ When you back up a DVD disc, be sure the source drive supports
recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs, it
might not be backed up correctly.
■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to
use the same type of disc.
■ You cannot partially delete any data written to a CD-RW, DVD-RW or
DVD+RW disc.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-15
Operating Basics
Data Verification
To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.
1. Click the Options button (
Options panels.
) on the RecordNow! Console to open the
2. Select the Data in the left-side menu.
3. Mark the Verify data written to the disc after burning check box in the
Data Options.
4. Click the OK button.
DLA for TOSHIBA
Note the following limitations when you use DLA:
■ This software supports only rewritable discs (DVD+RW, DVD-RW, and
CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are
not rewritable.
■ DLA does not support formatting a DVD-RAM disc and writing to it.
They are performed by DVD-RAM Driver Software. If DLA Format
menu may appear when inserting a DVD-RAM disc into the drive and
right-clicking the drive icon in Windows Explorer, please use
"DVDForm" to format this disc. You can run "DVDForm" by clicking the
Start button on the taskbar to display the Start menu and then selecting
"All Programs", "DVD-RAM", "DVD-RAM Driver" and "DVDForm"
sequentially.
■ Do not use any discs that have been formatted with packet writing
software other than DLA. Similarly, do not use any discs that have been
formatted with DLA with any packet writing software other than DLA.
When using a disc you are not familiar with, format it by selecting Full
Format before using it.
■ Do not use the Cut & Paste function for files and folders. A file or folder
that has been cut may be lost if writing fails due to an error on the disc.
■ When writing the Setup files for the program into a disc formatted by
DLA and starting Setup from this disc, an error may occur. In this case,
plase copy them to your hard disk and then run Setup.
Video
As for InterVideo WinDVD Creator Platinum. Only the model that can be
written in to DVD is attached.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-16
Operating Basics
When WinDVD Creator Platinum is used:
You can record video back to your digital camcorder via i.LINK (IEEE1394)
using WinDVD Creator Platinum. However, there is a case where its
playback sound is choppy.
1. Click the Windows Start button and select the Control Panel option.
2. Click the Performance and Maintenance icon in the Control Panel.
3. Click the System icon in the Performance and Maintenance window.
4. Click the Advanced tab in the System Properties window.
5. Click the Settings icon in the "Performance" section.
6. Click the Advanced tab in the Performance Options window.
7. Click the Change icon in the "virtual memory" section.
8. Select the Custom size button in the Virtual Memory window.
9. Specify much higher values for "Initial size" and "Maximum size."
10. Click the Set button in the Virtual Memory window.
11. Click the OK button in the Virtual Memory window.
How to make a DVD-Video
Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:
1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2]-[InterVideo
WinDVD Creator] to launch WinDVD Creator.
2. Click [Capture] button then capture the video data from the
DVCamcorder via IEEE1394.
3. Click [Edit] button then drag the video clips from [Video Library] tab to
the edit track.
4. Click [Make Movie] button in the top bar.
5. Double Click the Right arrow button icon in the center of right side.
6. Put a blank DVD-R/+R disc or an erased DVD-RW/+RW disc in the
drive.
7. Click [Start] to record to the disc.
8. When recording is finished, the tray opens.
How to learn more about InterVideo WinDVD Creator
Please refer to the on-line Help for additional InterVideo WinDVD Creator
information.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-17
Operating Basics
Important information for use
Note the following limitations when you write video DVD:
1. Editing digital video
■ Log in with Administrator rights to use WinDVD Creator.
■ Make sure that your computer is running on AC power when using
WinDVD Creator.
■ Operate the computer at Full Power. Do not use power-saving
features.
■ While you are editing DVD, you can display previews. However, if
another application is running, the preview might not display
properly.
■ WinDVD Creator cannot show video on the external monitor when in
simultaneous mode.
■ WinDVD Creator cannot edit or play copy protected content.
■ Do not change display settings while using WinDVD Creator.
■ Do not enter standby/hibernation mode while using WinDVD
Creator.
■ Do not operate WinDVD Creator immediately after turning on the
computer. Please wait until all Disc Drive activity has stopped.
■ When recording to a DV-Camcorder, to ensure you capture all of
your data, let the camcorder record for a few seconds before you
begin recording your actual data.
■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD
functions are not supported in this version.
■ While recording video to DVD or tape, please close all other
programs.
■ Do not run software like a screen saver because it can put a heavy
load on the CPU.
■ Do not run communication applications like a modem or a LAN.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-18
Operating Basics
2. Before recording the video to DVD
■ When you record to DVD disc, please use only discs recommended
by the Drive manufacturer.
■ Do not set the working drive to a slow device like a USB 1.1 hard
disk drive or it will fail to write DVD.
■ Do not perform any of the following actions:
■ Operate the computer for any other function, including using a
mouse or Touch pad or closing/opening the LCD panel.
■ Bump or cause vibration to the computer.
■ Use the Mode control button and Audio/Video control button to
reproduce music or voice.
■ Open the DVD drive.
■ Install, remove or connect external devices, including the
following:
PC card, SD card, USB devices, external display, i.LINK.
devices, optical digital devices.
■ Please verify your disc after recording important data.
■ DVD-R/+R/-RW disc cannot be written in VR format.
■ A maximum of about 2 hours of video data can be written in DVD
Video format to DVD-R/+R/-RW/+RW disc.
■ WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD
format.
■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the
disc may only play on your computer.
■ When writing to DVD disc, WinDVD Creator requires 2GB or more
over disk space every one hour of video.
■ When you make a fully recorded DVD, the chapter sequence may
not play correctly.
3. About Disc Manager
■ WinDVD Creator can edit one play list on a disc.
■ WinDVD Creator might show a different a thumbnail than you
previously set in CE DVD-RAM recorder.
■ Using the Disc Manager, you can edit DVD-VR format on DVDRAM,
DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW.
4. About recorded DVDs
■ Some DVD-ROM drives for personal computers or other DVD
players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.
■ When playing your recorded disc on your computer, please use the
WinDVD software application.
■ If you use an over-used rewritable disc, the full formatting might be
locked. Please use a brand new disc.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-19
Operating Basics
Media Care
This section provides tips on protecting data stored on your CD/DVDs and
diskettes.
Handles your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them:
1. Store your CD/DVDs in the container they came in to protect them and
keep them clean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/ DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the center hole.
Fingerprints on the surface can prevent the drive from properly reading
data.
5. Do not expose to direct sunlight, extreme heat or cold. Do not place
heavy objects on your CD/DVDs.
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry
cloth. Wipe from the center out, do not wipe in a circular direction
around the CD/ DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.
Diskettes
1. Store your diskettes in the container they came in to protect them and
keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it
with a soft damp cloth.
2. Do not slide back the diskette's protective metal covering or touch the
diskette's magnetic surface. Fingerprints may prevent the diskette drive
from reading data from the diskette.
3. Data may be lost if the diskette is twisted; bent; or exposed to direct
sunlight, extreme heat or cold.
4. Do not place heavy objects on your diskettes.
5. Do not eat, smoke, or use erasers near your diskettes. Foreign particles
inside the diskette's jacket can damage the magnetic surface.
6. Magnetic energy can destroy data on diskettes. Keep your diskettes
away from speakers, radios, television sets and other sources of
magnetic fields.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-20
Operating Basics
Using the internal modem
This section describes how to make settings and connect the modem.
Refer to the computer's online help files for more information. Refer also to
the online help files for your modem software.
The internal modem does not support the voice functions described in the
help files. All data and fax functions are supported.
■ In case of a lightning storm, unplug the modem cable(optional) from the
telephone jack.
■ Do not connect the modem to a digital telephone line. A digital line will
damage the modem.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Do not use this product near water, for example, near a bathtub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.
2. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord indicated in this manual.
Region selection
Telecommunication regulations vary from one country/region to another, so
you will need to make sure the internal modem's settings are correct for the
country/region in which it will be used.
1. Point to "All Programs", point to "TOSHIBA", point to "Networking"
and click "Modem Region Select".
Do not use the Country/Region Select function in the Modem setup utility
in the Control Panel if the function is available. If you change the Country/
Region in the Control Panel, the change may not take effect.
2. The Region Selection icon will appear in the Windows Task Bar.
The Region Selection icon
3. Click the icon with the primary mouse button to display a list of regions
that the modem supports. A sub menu for telephony location
information will also be displayed. A check will appear next to the
currently selected region and telephony location.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-21
Operating Basics
4. Select a region from the region menu or a telephony location from the
submenu.
■ When you click a region it becomes the modem's region selection,
and the New Location for telephony will be set automatically.
■ When you select a telephony location, the corresponding region is
automatically selected and it becomes the modem's current region
setting.
Properties menu
Click the icon with the secondary mouse button to display the following
menu.
The properties menu
Setting
You can enable or disable the following settings:
AutoRun Mode
Region Select Utility starts automatically when you start up the operating
system.
Open the Dialing Properties dialog box after selecting
region.
The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current
Location region code do not match.
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is
displayed. Select the COM port for your modem to use.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-22
Operating Basics
Dialing Properties
Select this item to display the dialing properties.
If you are using the computer in Japan, technical regulations described in
the Telecommunications Business Law require that you select Japan
region mode. It is illegal to use the modem in Japan with any other
selection.
Connecting
To connect the internal modem cable(optional), follow the steps below.
■ In case of a lightning storm, unplug the modem cable(optional) from the
telephone jack.
■ Do not connect the modem to a digital telephone line. A digital line will
damage the modem.
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack
Connecting the internal modem
Do not pull on the cable or move the computer while the cable is
connected.
If you use a storage device such as a DVD-ROM drive or HDD connected
to a 16-bit PC card, modem speed might be slow or communication might
be interrupted.
If modem speed is low or communication is interrupted when you are using
modem, please check and set CPU speed to Maximum by TOSHIBA
Power Saver utility.
Disconnecting
To disconnect the internal modem cable(optional), follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. Disconnect the cable from the computer in the same manner.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-23
Operating Basics
LAN
The computer is equipped with LAN circuits that support Ethernet LAN (10
megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits
per second, 100BASE-TX). This section describes how to connect/
disconnect to a LAN.
Do not install or remove an optional memory module while Wake-up on
LAN is enabled.
Wake-up on LAN does not work without the AC adaptor. Leave it
connected, if you are using this feature.
Connecting LAN cable
The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer's default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.
If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable. You cannot use a
CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect with either a CAT5 or a CAT3.
To connect the LAN cable, follow the steps below.
1. Turn off the power to the computer and to all external devices
connected to the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.
Connecting the LAN cable
3. Plug the other end of the cable into a LAN hub connector. Check with
your LAN administrator before connecting to a hub.
Disconnecting LAN cable
To disconnect the LAN cable, follow the steps below.
1. Pinch the lever on the connector in the computer's LAN jack and pull
out the connector.
2. Disconnect the cable from the LAN hub in the same manner. Check
with your LAN administrator before disconnecting from the hub.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-24
Operating Basics
Wireless LAN
The wireless LAN is compatible with other LAN systems that comply with
the IEEE 802.11a+g, and 802.11g wireless LAN standards.
It supports the following:
■ Automatic Transmit Rate Select mechanism in the transmit range of 54,
11, 5.5, 2 and 1 Mbit/s. (54 Mbps is available only with 802.11a or
802.11g.)
■ Advanced Encryption Standard (AES) data encryption, based on 128bit
encryption algorithm. (Revision G, A/G combo type.)
Wake-up on LAN does not function on a Wireless LAN.
■ Frequency Channel Selection (5GHz and 2.4 GHz)
■ Roaming over multiple channels
■ Card Power Management
■ Wired Equivalent Privacy (WEP) data encryption. Wake-up on LAN
does not function on a wireless LAN.
Security
1. Be sure to enable WEP(encryption) function. Otherwise you computer
will allow the illegal access by outside through Wireless LAN to cause
illegal intrusion, eavesdropping, and loss or destruction of stored data.
TOSHIBA strongly recommend the customer to enable the WEP
function.
2. TOSHIBA is not liable for the eavesdropping of data due to the use of
Wireless LAN and the damage thereof.
Wireless communication switch
You can enable or disable wireless LAN function, with the on/off switch. No
transmissions are sent or received when the switch is off. Slide the switch
forward to turn it on and backward to turn it off.
Turn the switch off in airplanes and hospitals. Check the LED. It stops
glowing when the wireless communication function is off.
Wireless communication LED
The LED indicates the status of the wireless communication functions.
LED status
LED off
Indication
Wireless communication switch is set to off
Wireless communication switch is on
LED glows
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-25
Operating Basics
TV-Out
Use the TV-Out jack to connect to a television. Be sure to use a 4 pin type
TV out
Setting up more than one display
You can set up your computer to utilize more than one display, effectively
spreading a single desktop screen across two monitors.
The Display Properties window allows you to adjust more precisely the
relative positioning of the two displays when they are configured as an
extended desktop. On the Display Properties window, the two displays can
be positioned horizontally, vertically or in any diagonal configuration you
wish, as shown below.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-26
Operating Basics
If an external display will not be connected next time you use your
computer, you should cancel any extended desktop or clone display
settings before shutting down your computer.
Clone display settings are those where more than one device has been
selected and is simultaneously applicable.
Cleaning the computer
To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.
■ Be careful not to spill liquids into the computer. If the computer does get
wet, turn the power off immediately and let the computer dry completely
before you turn it on again.
■ Clean the computer using a slightly damp (with water) cloth. You can
use glass cleaner on the display. Spray a small amount of cleaner on a
soft, clean cloth and wipe the screen gently with the cloth.
Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.
Moving the computer
The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.
■ Make sure all disk activity has ended before moving the computer.
Check the Built-in HDD and Diskette/Optical Media drive indicators
on the computer.
■ If a diskette is in the diskette drive, remove it.
■ If a disc is in the optical media drive, remove it. Also make sure the
optical media drive drawer is securely closed.
■ Turn off the power to the computer.
■ Disconnect all peripherals before moving the computer.
■ Close the display. Do not pick up the computer by its display panel or
back (where the interface ports are located).
■ Close all port covers.
■ Disconnect the AC adaptor if it is connected.
■ Use the carrying case when transporting the computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4-27
Satellite P30 Series
Chapter 5
The Keyboard
The computer's keyboard layouts are compatible with a 101/102-key
enhanced keyboard. By pressing some keys in combination, all the 101/
102-key keyboard functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region's
keyboard layout your computer is configured with. Keyboards for numerous
languages are available.
There are five types of keys: typewriter keys, keypad overlay, function keys,
soft keys and cursor control keys. The typewriter keys and keypad overlay
keys are gray. The other keys are dark gray.
Typewriter keys
The typewriter keys, produce the upper- and lower-case letters, numbers,
punctuation marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and
using a computer keyboard:
■ Letters and numbers produced in computer text vary in width. Spaces,
which are created by a space character may also vary depending on
line justification and other factors.
■ The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
■ The uppercase O (oh) and the 0 (zero) are not interchangeable.
■ The Caps Lock function key locks only the alphabetic characters in
uppercase while the shift lock on a typewriter places all keys in the
shifted position.
■ The Shift keys, the Tab key, and the BkSp (backspace) key perform the
same function as their typewriter counterparts but also have special
computer functions.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-1
The Keyboard
F1 ... F12 function keys
The function keys, not to be confused with Fn, are the 12 keys at the top of
your keyboard. These keys are dark gray, but function differently from the
other dark gray keys.
F1 through F12 are called function keys because they execute
programmed functions when pressed. Used in combination with the Fn key,
keys marked with icons execute specific functions on the computer. See
the section, Soft keys: Fn key combinations, in this chapter. The function
executed by individual keys depends on the software you are using.
Soft keys: Fn key combinations
The Fn (function) is unique to TOSHIBA computers and is used in
combination with other keys to form soft keys. Soft keys are key
combinations that enable, disable or configure specific features.
Some software may disable or interfere with soft-key operations. Soft-key
settings are not restored by the Standby feature.
Emulation keys
Your software may require you to use keys that the keyboard does not
have. Pressing the Fn key and one of the following keys simulates the
enhanced keyboard's functions.
Press Fn + F10 or Fn + F11 to access the integrated keypad. When
activated, the gray keys with white numbers become numeric keypad keys
(Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay
section in this chapter for more information on how to operate these keys.
The power on default for both settings is off.
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power
on default is off.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2
The Keyboard
Press Fn + Enter to simulate Enter on the enhanced keyboard's numeric
keypad.
Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key.
Hotkeys
Fn + ESC
Fn + F1
Volume Mute Turns the volume on and off.
Instant Security Enters screen saver mode and
blanks the screen. To restore your desktop, press
any key or use the TouchPad.
Fn + F2
Fn + F3
Fn + F4
Fn + F5
Power Save Modes Displays the power save
modes and lets you change the power settings
Standby This hot key switches the system to
Standby mode.
Hibernate This hot key switches the system to
Hibernate mode.
Display Selection Changes displays.
Default resolution for simultaneous mode is set to XGA (1024x768). If you
connect an external monitor that is not XGA resolution, change it in
"Display Properties".
Fn + F6
Fn + F7
Fn + F8
Brightness Down
Brightness Up
Wireless Device Controls Pressing this hot key
allows you to switch between active wireless
devices. Only works if the wireless switch has
already been turned on.
Fn + F9
TouchPad On/Off
Fn + F10
Cursor Keypad On/Off This hot key enables/
disables the embedded cursor keypad. Numeric
lock state is logically disabled. See Chapter 3,
Getting Started for more information.
User’s Manual
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Keyboard
Fn + F11
Numeric Keypad On/Off This hot key enables/
disables the embedded numeric keypad. Numeric
lock state is logically enabled. See Chapter 3,
Getting Started for more information.
Fn + F12
Scroll Lock On/Off
Fn + Space
Change Resolution Cycles sequentially from
the current resolution to 800x600 to 1024x768
and back again to the original resolution.
.
Fn + 1
Fn + 2
TOSHIBA Zooming Utility (reduce) To reduce
the icon size on the desktop or the application
window, press 1 key while holding down teh Fn
key.
TOSHIBA Zooming Utility (enlarge) To
enlarge the icon size on the desktop or the
application window, press 2 key while holding
down teh Fn key.
Windows special keys
The keyboard provides two keys that have special functions in Windows
XP. One activates the Start menu and the other has the same function as
the secondary mouse button.
This key activates the Windows XP Start menu
This key has the same function as the secondary mouse button.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4
The Keyboard
Keypad overlay
Your computer's keyboard does not have an independent numeric keypad,
but its numeric keypad overlay functions like one.
The keys in the center of the keyboard with white letters make up the
numeric keypad overlay. The overlay provides the same functions as the
numeric keypad on the 101/102-key enhanced keyboard in figure 5-2.
Turning on the overlays
The numeric keypad overlay can be used for numeric data input or cursor
and page control.
Arrow mode
To turn on the Arrow mode, press Fn + F10 (Arrow mode indicator lights).
Now try cursor and page control using the keys shown in figure 5-2. Press
Fn + F10 again to turn off the overlay.
Numeric mode
To turn on the Numeric mode, press Fn + F11 (Numeric mode indicator
lights). Now try numeric data entry using the keys in figure 5-2. Press Fn +
F11 again to turn off the overlay.
The numeric keypad overlay (U.S.)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-5
The Keyboard
Temporarily using normal keyboard (overlay on)
While using the overlay, you can temporarily access the normal keyboard
without turning off the overlay:
1. Hold down Fn and press any other key. All keys will operate as if the
overlay were off.
2. Type upper-case characters by holding down Fn + Shift and pressing a
character key.
3. Release Fn to continue using the overlay.
Temporarily using overlay (overlay off)
While using the normal keyboard, you can temporarily use the keypad
overlay without turning it on:
1. Press and hold down Fn.
2. Check the keyboard indicators. Pressing Fn turns on the most recently
used overlay. If the Numeric mode indicator lights, you can use the
overlay for numeric entry. If the Arrow mode indicator lights, you can
use it for cursor and page control.
3. Release Fn to return to normal keyboard operation.
Temporarily changing modes
If the computer is in Numeric mode, you can switch temporarily to Arrow
mode by pressing a shift key.
If the computer is in Arrow mode, you can switch temporarily to Numeric
mode by pressing a shift key.
Generating ASCII characters
Not all ASCII characters can be generated using normal keyboard
operation. But, you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold Alt + Fn.
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display
screen.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5-6
Satellite P30 Series
Chapter 6
Power and Power-Up Modes
The computer's power resources include the AC adaptor and internal
batteries. This chapter gives details on making the most effective use of
these resources including charging and changing batteries, tips for saving
battery power, and power up modes.
Power conditions
The computer's operating capability and battery charge status are affected
by the power conditions: whether an AC adaptor is connected, whether a
battery is installed and what the charge level is for the battery.
Power on
Power off (no operation)
AC adaptor Battery fully
• Operates
• No charge
• LED: Battery green
• No charge
• LED: Battery green
DC IN green
connected
charged
DC IN green
Battery partially • Operates
• Charge
• LED: Battery orange
DC IN green
charged or no
charge
• Charge
• LED: Battery orange
DC IN green
No battery
installed
• Operates
• No charge
• LED: Battery off
DC IN green
• No charge
• LED: Battery off
DC IN green
User’s Manual
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Power and Power-Up Modes
Power off (no operation)
Power on
AC adaptor Battery charge • Operates
—
not
connected
is above low
battery trigger
point
• LED: Battery off
DC IN off
Battery charge • Operates
—
is below low
battery trigger
point
• Alarm sounds (depending
on the TOSHIBA Power
Saver utility setting)
• LED: Battery flashes
amber
DC IN off
Computer goes into
Hibernation or shuts down
(depending on the
TOSHIBA Power Saver
utility setting)
Battery charge
exhausted
—
—
• No operation
• LED: Battery off
No battery
installed
DC IN off
Power indicators
As shown in the above table, the Battery, DC IN and Power indicators on
the system indicator alert you to the computer's operating capability and
battery charge status.
Battery indicator
Check the Battery indicator to determine the status of the battery. The
following indicator lights indicate the battery status.
Flashing amber
The battery charge is low. The AC adaptor must
be connected to recharge the battery
Amber
Indicates the AC adaptor is connected and
charging the battery.
Green
Indicates the AC adaptor is connected and the
battery is fully charged.
No light
Under any other conditions, the indicator does
not light.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2
Power and Power-Up Modes
DC IN indicator
Check the DC IN indicator to determine the power status with the AC
adaptor connected:
Green
Indicates the AC adaptor is connected and
supplying proper power to the computer.
No light
Indicates the AC adaptor is not connected.
Power indicator
Check the Power indicator to determine the power status with the AC
adaptor connected:
Blue/Green
The power button will shinning blue while power
is being supplied to the computer and the
computer is turned on. The power indicator in
front of computer will shinning green while
system is on.
Blinking amber
No light
Indicates power is being supplied to the
computer while the computer is in Standby
mode.
Under any other conditions, the indicator does
not light.
Battery types
The computer has two types of batteries:
■ Battery pack
■ Real Time Clock (RTC) battery
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3
Power and Power-Up Modes
Battery pack
When the AC adaptor is not connected, the computer's main power source
is a removable lithium ion battery pack, also referred to in this manual as
the battery.
You can purchase additional battery packs for extended use of the
computer away from an AC power source.
The battery is a disposable item. When its operation becomes short even
when fully charged, replace it with a new one.
■ The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.
■ Do not remove the Battery Pack while the computer is in Standby
mode. Data is stored in RAM, so if the computer loses power, it will be
lost.
■ Battery type (depending on the model purchased):
8 cell-PA3385U-1BAS, PA3385U-1BRS
12 cell- PA3383U-1BAS, PA3383U-1BRS
Real Time Clock battery
The Real Time Clock (RTC) battery provides power for the internal real
time clock and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this
data and the real time clock and calendar stop working. The following
message appears when you turn on the power:
ERROR 0271:Check date and time settings.
WARNING 0251:System CMOS checksum bad - Default
configuration used.
Press <F1> to resume, <F2> to Setup
The computer's RTC battery is a lithium ion battery and should be replaced
only by your dealer or by a TOSHIBA service representative. The battery
can explode if not properly replaced, used, handled or disposed of.
Dispose of the battery as required by local ordinances or regulations.
When this error appears, the following action is recommended.
1. Plug in AC over 24 hours
2. Press F2 to enter BIOS setup menu
3. Set correct time and date
If you still see error message after above action, please get contact with
TOSHIBA service.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4
Power and Power-Up Modes
Care and use of the battery pack
The battery pack is a vital component of portable computing. Taking proper
care of it will help ensure longer operating time on battery power as well as
a longer life for your battery pack. Follow the instructions in this section
carefully to ensure safe operation and maximum performance.
Safety precautions
Mishandling of batteries can cause death, serious injury or property
damage.
Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, which could result in
death or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, which if not avoided,
may result in moderate or minor injury or property damage.
Note: Provides important information.
Danger
1. Never try to dispose of the battery pack by burning or expose it to a
heating device such as a microwave oven. The battery pack could
explode and cause bodily injury.
2. Never try to disassemble, repair or otherwise tamper with a battery
pack. The battery pack will overheat and ignite. Leakage of caustic
alkaline solution or other electrolytic substances will cause fire or injury,
possibly resulting in death or serious injury.
3. Never short-circuit the battery pack by contacting the terminals with a
metal object. A short-circuit can cause fire or otherwise damage the
battery pack and possibly cause injury. To avoid accidental short-circuit,
always wrap the battery pack in plastic and cover the terminals with
electrical tape when storing or disposing of the battery pack.
4. Never puncture the battery pack with a nail or other sharp object. Never
strike it with a hammer or other object. Never step on it.
5. Never try to charge the battery pack in any manner other than that
described in the user's manual. Never connect the battery pack to a
plug socket or to an automobile's cigarette lighter socket. It may rupture
or ignite.
6. Use only the battery pack supplied with the computer or other device or
an battery pack approved by the computer or device's manufacturer.
Battery packs have different voltages and terminal polarities. Use of an
improper battery could cause smoke, fire or rupture of the battery pack.
7. Never subject a battery pack to heat, such as storage near a heat
source. Exposure to heat can cause the battery pack to ignite, explode
or leak caustic liquid and cause death or serious injury. It could also fail
or malfunction causing data loss.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5
Power and Power-Up Modes
8. Never expose the battery pack to abnormal shock, vibration or
pressure. The battery pack's internal protective device will fail, causing
it to overheat, explode, ignite or leak caustic liquids possibly resulting in
death or serious injury.
9. Never let a battery pack become wet. A wet battery pack will overheat,
ignite or rupture possibly resulting in death or serious injury.
Warning
1. Never allow caustic electrolyte fluid leaked from a battery pack to
contact your eyes, skin or clothing. If caustic electrolyte fluid should
contact your eyes, immediately wash your eyes with large amounts of
running water and seek medical attention, to help prevent eye damage.
It electrolyte fluid should contact your skin, immediately wash it under
running water to prevent rash. If it contacts your clothes, promptly
remove them to prevent the fluid from contacting your skin or eyes.
2. Immediately turn off the power, disconnect the AC adaptor and remove
the battery if any of the following events are observed in the battery
pack: offensive or unusual odor, excessive heat, discoloration or
deformation. Never use the computer again until it has been checked
by a TOSHIBA service provider. It might generate smoke or fire, or the
battery pack might rupture.
3. Make sure the battery is securely installed in the computer before
attempting to charge the battery pack. Improper installation could
generate smoke or fire, or cause the battery pack to rupture.
4. Keep the battery pack out or reach of infants and children. It can cause
injury.
Caution
1. Never continue to use a battery pack after its recharging capacity has
become impaired, or after the display of a warning message indicating
that the battery pack's power is exhausted. Continued use of an
exhausted or impaired battery pack could cause the loss of data.
2. Never dispose of battery packs with normal trash. Bring them to your
TOSHIBA dealer or to another recycling center to save resources and
prevent environmental damage. Cover the terminals with electrical tape
to prevent short-circuits, which could cause the battery pack to ignite or
rupture.
3. Use only battery packs recommended by TOSHIBA as replacements.
4. Always make sure the battery pack is installed correctly and securely.
Otherwise, a battery pack could fall out and possibly cause injury.
5. Charge the battery pack only in an ambient temperature between 5 and
30 degrees Celsius. Otherwise, the electrolyte solution might leak,
battery pack performance might deteriorate and the battery life might be
shortened.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-6
Power and Power-Up Modes
6. Be sure to monitor the remaining battery power. If the battery pack and
real time clock battery discharge completely, Standby and Suspend will
not function and data in memory will be lost. Also, the computer might
register an incorrect time and date. In this case, connect the AC adaptor
to recharge the batteries.
7. Never install or remove the battery pack without first turning off the
power and disconnecting the AC adaptor. Never remove the battery
pack while the computer is in Suspend or Standby mode. Data will be
lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable
the Wake-up on LAN function.
2. To ensure the battery pack maintains maximum capacity, operate the
computer on battery power once a week until the battery pack is fully
discharged. Refer to the section Extending battery life in this chapter for
procedures. If the computer is continuously operated on AC power for
an extended period, more than a week, the battery might fail to retain a
charge. It might not function efficiently over the expected life of the
battery pack and the Battery indicator might not indicate a low-battery
condition.
3. After the battery pack is charged, avoid leaving the AC adaptor
connected and the computer turned off for more than a few hours at a
time. Continuing to charge a fully charged battery pack can damage the
battery.
Charging the batteries
When the power in the battery pack becomes low, the Battery indicator
flashes amber indicating that only a few minutes of battery power remain. If
you continue to use the computer while the Battery indicator flashes, the
computer enables Hibernation mode (so you don't lose data) and
automatically turns off.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack while it is installed in the computer, connect the
AC adaptor to the DC IN socket and plug the other end into a working
outlet.
The Battery indicator glows amber when the battery is being charged.
Use only the computer connected to an AC power source to charge the
battery pack. Do not attempt to charge the battery pack with any other
charger.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-7
Power and Power-Up Modes
Time
The following table shows the time required to fully charge a discharged
battery.
Charging time (hours)
Battery type
Battery pack
RTC battery
Power on
Power off
about 12 or longer
about 24
about 4 or longer
about 24 with AC or
Battery pack
The charging time when the computer is on is affected by ambient
temperature, the temperature of the computer and how you use the
computer.
If you make heavy use of external devices, for example, the battery might
scarcely charge at all during operation. Refer also to the section
Maximizing battery operating time.
Battery charging notice
The battery may not charge right away under the following conditions:
■ The battery is extremely hot or cold. To make sure the battery charges
to its full capacity, charge the battery at room temperature of 10° to
30°C (50° to 86°F).
■ The battery is nearly completely discharged. Leave the AC adaptor
connected for a few minutes and the battery should begin charging.
Once a battery pack is fully charged, it is recommended that you operate
the computer only on battery power until the battery pack completely
discharges. Doing so extends battery life and helps ensure accurate
monitoring of battery capacity.
The Battery indicator may show a rapid decrease in battery operating time
when you try to charge a battery under the following conditions:
■ The battery has not been used for a long time.
■ The battery has completely discharged and been left in the computer for
a long time.
■ A cool battery is installed in a warm computer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8
Power and Power-Up Modes
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power
on until the power automatically shuts off.
2. Plug in the AC adaptor.
3. Charge the battery until the Battery indicator glows green.
Repeat these steps two or three times until the battery recovers normal
capacity.
Leaving the AC adaptor connected will shorten battery life. At least once a
month, run the computer on battery power until the battery is fully
discharged, then recharge the battery.
Monitoring battery capacity
Remaining battery power can be monitored by the TOSHIBA Power Saver
■ Wait for a moment after turning on the computer before trying to
monitor the remaining operating time. The computer needs this time to
check the battery's remaining capacity.
■ With repeated discharges and recharges, the battery's capacity will
gradually decrease. Therefore, an often used, older battery will not
operate for as long as a new battery even when both are fully charged.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-9
Power and Power-Up Modes
Maximizing battery operating time
A battery's usefulness depends on how long it can supply power on a
single charge.
How long the charge lasts in a battery depends on:
■ How you configure the computer (for example, whether you enable
battery power saving options). The computer provides a battery save
mode to conserve battery power. This mode has the following options:
■ Display auto off
■ HDD auto off
■ System auto off
■ LCD brightness
■ How often and how long you use the hard disk, CD-ROM and the
diskette drive.
■ How much charge the battery contained to begin with.
■ How you use optional devices, such as a PC Card, to which the battery
supplies power.
■ Enabling Resume mode conserves battery power if you are frequently
turning the computer off and on.
■ Where you store your programs and data.
■ Closing the display when you are not using the keyboard saves power.
■ Operating time decreases at low temperatures.
■ The condition of the battery terminals. Make sure the battery terminals
stay clean by wiping them with a clean dry cloth before installing the
battery pack.
Retaining data with power off (standby mode)
When you turn off your computer with fully charged batteries, the batteries
retain data for the following approximate time periods:
Battery
Approximately 3 days (Standby mode, 12-cell)
Approximately 2 days (Standby mode, 8-cell)
Approximately1 month (Shut down mode, both)
RTC battery
Approximately 1 month
Extending battery life
To maximize the life of your battery pack:
■ If you have extra battery packs, rotate their use.
■ If you will not be using the system for an extended period, remove the
battery pack.
■ Store spare battery packs in a cool dry place out of direct sunlight.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-10
Power and Power-Up Modes
Replacing the battery pack
When the battery pack reaches the end of its operating life you will need to
install a new one. If the Battery indicator flashes amber shortly after the
battery has been fully recharged, the battery pack needs to be replaced.
You might also replace a discharged battery pack with a charged spare
when you are operating your computer away from an AC power source.
This section explains how to remove and install the battery pack.
Removing the battery pack
To replace a discharged battery pack, follow the steps below.
■ When handling battery packs, be careful not to short circuit the
terminals. Also do not drop, hit or otherwise apply impact; do not
scratch or break the casing and do not twist or bend the battery pack.
■ Do not remove the battery pack while the computer is in Standby mode.
Data in memory will be lost.
1. Save your work.
2. Turn the computer's power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Turn the computer upside down.
5. Unlock the Battery Double Lock.
6. Slide the battery latch to the right, then pull the battery out of the battery
bay.
2
1
Removing the battery pack
For environmental reasons, do not throw away a spent battery pack.
Please return spent battery packs to your TOSHIBA dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-11
Power and Power-Up Modes
Installing the battery pack
To install a battery pack, follow the steps below.
The battery pack is a lithium ion battery, which can explode if not properly
replaced, used, handled or disposed of. Dispose of the battery as required
by local ordinances or regulations. Use only batteries recommended by
TOSHIBA as replacements.
1. Turn the computer's power off.
2. Disconnect all cables connected to the computer.
3. Hold the battery pack so that the label faces down and the connectors
on the battery face the connectors on the computer.
4. Gently press the battery into the battery bay until the latch clicks into
place.
5. Lock the Battery Double Lock to secure the installation.
Installing the battery pack
Power-up modes
The computer has three power-up modes:
■ Hibernation (saves data in memory to the hard disk)
■ Standby (Power remains on, saving data in RAM, but the CPU and all
other devices enter sleep mode.)
■ Boot (does not save data in memory)
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-12
Power and Power-Up Modes
Panel power off/on
You can set up your computer so that power turns off automatically when
you close the display panel.
When you open the panel, power turns on in Standby or Hibernation mode
but not in boot mode.
If the panel power off function is enabled and you use Shut down
Windows, do not close the display until the shut down function is
completed.
System automatic Standby/ Hibernation
This feature automatically turns off the system in Standby or Hibernation
mode if the computer is not used for a set duration.
how to set the duration.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6-13
Satellite P30 Series
Chapter 7
Optional Devices
Optional devices can expand the computer's capabilities and its versatility.
This chapter describes connection or installation of the following types of
devices, which are available from your TOSHIBA dealer:
Cards/Memory
■ PC cards
■ SD (Secure Digital)/MMC (MultiMediaCard)/SM (SmartMedia)/MS
(Memory Stick)/MS Pro (Memory Stick Pro)/xD (xD-Picture Card) cards
■ Memory modules
Power devices
■ Battery pack
■ AC adaptor
Peripheral devices
■ External monitor
■ Television
■ i.LINK (IEEE1394)
■ Security lock
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-1
Optional Devices
PC cards
The computer is equipped with a PC card expansion slot that can
accommodate one 5 mm Type II card. Any PC card that meets industry
standards (manufactured by TOSHIBA or other vendor) can be installed.
The slots support 16-bit PC cards, including PC card 16's multifunction card
and CardBus PC cards. CardBus supports the new standard of 32-bit PC
cards. The bus provides superior performance for the greater demands of
multimedia data transmission.
■ Do not install a PC card while the computer is in Standby or Hibernation
mode. Some cards might not work properly.
■ Furthermore, an HDD or CD-ROM connected to a 16-bit PC card might
affect the performance of the computer's sound system and data
transmission, including slower transmission speeds and dialing errors.
Installing a PC card
One PC card connector is located on the right side of the computer. The
computer's hot-install feature lets you install PC cards while the computer's
power is on.
Do not install a PC card while the computer is in Standby or Hibernation
mode. Some cards might not work properly.
To install a PC card, follow the steps below.
1. Insert the PC card.
2. Press gently to ensure a firm connection.
Installing a PC card
After installing the card, refer to the card's documentation and check the
configuration in Windows to make sure it is appropriate for your card.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2
Optional Devices
Removing a PC card
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Click the PC card you want to remove.
3. Press the eject button of the PC card to extend it.
4. Press the extended eject button to pop the card out slightly.
5. Grasp the PC card and remove it.
Removing a PC card
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-3
Optional Devices
SD/MMC/SM/MS/MS Pro/xD Memory Cards
The computer is equipped with a Multiple Digital Media Card Slot that can
accommodate SD/MMC/SM/MS/MS Pro/xD memory cards. These memory
cards let you easily transfer data from devices, such as digital cameras and
Personal Digital Assistants, that use flash-memory. See below for the card
capacities:
Card Type
SD
Capacities
8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB
8MB, 16MB, 32MB, 64MB, 128MB, 256MB
4MB, 8MB, 16MB, 32MB, 64MB, 128MB
8MB, 16MB, 32MB, 64MB, 128MB, 256MB
256MB, 512MB, 1GB
MMC
SM
MS
MS Pro
xD
4MB, 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,
512MB
Keep foreign objects out of the memory card slot. A pin or similar object
can damage the computer's circuitry.
Do not format Memory Cards by Windows. It might cause that Memory
Cards cannot be used on peripheral devices.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4
Optional Devices
Installing an Memory card
To install a memory card, follow the steps below.
1. Insert the memory card.
2. Press gently to ensure a firm connection.
Inserting an memory card
Be sure the memory card is oriented properly before you insert it.
If Windows fails to read the memory card, remove it then reinsert it.
■ Two kinds of cards will not work at the same time. Insert only one card
when using Multiple Digital Media Card Slot.
■ 5V SmartMedia card is not supported.
■ Memory Stick Duo/ Memory Stick Pro Duo/ Mini-SD card is not
supported.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-5
Optional Devices
Removing a Memory card
To remove a memory card, follow the steps below.
1. Click the Safety Remove Hardware icon on the Task Bar.
2. Stop a memory card device which you want to remove.
3. Grasp the card and remove it.
Removing a memory card
■ Make sure the memory card indicator is out before you remove the
card or turn off the computer's power. If you remove the card or turn off
the power while the computer is accessing the card you may lose data
or damage the card.
■ Do not remove the card while the computer is in Standby or Hibernation
mode. The computer could become unstable or data in the memory
card could be lost.
■ Do not turn off or make computer in Standby or Hibernation mode
during data is being transferred. The computer could become unstable
or data in the memory card would be lost.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6
Optional Devices
Memory card care
Set the write-protect switch to the lock position, if you do not want to record
data.
1. Do not write to a memory card if the battery power is low. Low power
could affect writing accuracy.
2. Do not remove a memory card while read/write is in progress.
3. The memory card is designed so that it can be inserted only one way.
Do not try to force the card into the slot.
4. Do not leave a memory card partially inserted in the slot. Press the
memory card until you hear it click into place.
5. Do not twist or bend memory cards.
6. Do not expose memory cards to liquids or store in humid areas or lay
media close to containers of liquid.
7. After using a memory card, return it to its case.
8. Do not touch the metal part or expose it to liquids or let it get dirty.
Memory expansion
You can install additional memory in the computer's memory module socket
to increase the amount of RAM. This section describes how to install and
remove a memory module.
■ Before you install or remove a memory module, turn off the computer
with the Shut Down option in the Windows Start menu. If you install or
remove a memory module while the computer is in Standby or
Hibernation mode, data will be lost.
■ Some memory modules can be physically installed but are not
compatible with the computer. In this case the computer will issue a
warning.
Satellite P30 series: There will be a long beep, 3 short beeps, 3 more
short beeps and then a long beep when you turn the power on. In this
case, shut down the power and remove the incompatible memory
module.
CAUTION: If you want to upgrade system memory, you should only
use certified modules. Ask your vendor or check the TOSHIBA web site
for a list of approved memory products.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-7
Optional Devices
Installing memory module
If you use the computer for a long time, the memory modules will become
hot. In this case, let the memory modules cool to room temperature before
you replace them.
Follow these steps to install a memory module:
1. Set the computer to boot mode and turn off the power.
Do not try to install a memory module under the following conditions. You
can damage the computer and the module.
■ The computer is turned on.
■ The computer was shut down using the Stand by mode.
■ Power to the optical media drive has been turned on by the CD Power
switch.
2. Remove all cables connected to the computer.
3. Turn the computer upside down and remove the battery (refer to
4. Remove the two screws securing the memory module socket cover.
5. Slide your fingernail or a thin object under the cover and lift it off.
Removing the memory module socket cover
6. Fit the module's connectors into the computer's connectors at about a
45 degree angle and press the module carefully to ensure a firm
connection.
Do not touch the connectors on the memory module or on the computer.
Debris on the connectors may cause memory access problems.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-8
Optional Devices
7. Push the module down so it lies flat. Latches on either side will click into
place to secure the module.
2
1
Installing a module
8. Seat the cover and secure it with two screws.
10. Turn the power on and make sure the added memory is recognized.
Removing memory module
If you use the computer for a long time, the memory modules will become
hot. In this case, let the memory modules cool to room temperature before
you replace them.
To remove the memory module, make sure the computer is in boot mode
then:
1. Be sure the power is off and all cables are disconnected from the
computer.
Do not try to remove a memory module with the computer turned on. You
can damage the computer and the module.
2. Turn the computer upside down and remove the battery and two screws
securing the memory module socket cover.
3. Slide your fingernail or a thin object under the cover and lift it off.
4. Push the latches to the outside to release the module. A spring will
force one end of the module up.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-9
Optional Devices
5. Grasp the module and pull it out.
Do not touch the connectors on the memory module or on the computer.
Debris on the connectors may cause memory access problems.
Removing the memory module
6. Seat the cover and secure its screws.
7. Replace the battery.
Additional battery pack
You can increase the portability of the computer with additional battery
packs. If you're away from an AC power source and your battery runs low,
Additional AC adaptor
If you frequently carry the computer to different sites such as your home
and office, having an AC adaptor at each location reduces the weight and
bulk of your load.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-10
Optional Devices
External monitor
An external analog monitor can be connected to the external monitor port
on the computer.
To connect a monitor, follow the steps below.
1. Turn the computer off.
2. Connect the monitor to the external monitor port.
3. Turn the monitor's power on.
4. Turn the computer on.
When you turn on the power, the computer automatically recognizes the
monitor.
To change the display settings, press Fn + F5. If you disconnect the
monitor before you turn the computer off, be sure to press Fn + F5 to switch
using hot keys to change the display setting.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-11
Optional Devices
Television
A television can be connected to the video out port on the computer.
To connect a television, follow the steps below.
1. Turn the computer off.
2. Use a video cable (not supplied) to connect the television to the video
out port.
3. Turn the television on.
4. Turn the computer on.
You can use the hotkeys Fn + F5 or use the TV-Out button to change the
If a television is connected to the computer, set the TV type in Display
Properties. Follow the steps below.
1. Click Start > Control Panel >Appearance and Themes.
2. Choose Display to open the Display Properties dialog box
3. Click the Settings tab.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-12
Optional Devices
4. Click the Advanced button and choose Displays
5. Click the TV button to open the TV Properties dialog box.
6. Adjust the TV properties accordingly
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-13
Optional Devices
i.LINK (IEEE1394)
i.LINK (IEEE1394) is used for high-speed data transfer for a range of
compatible devices such as:
■ Digital video cameras
■ Hard disk drives
■ MO drives
■ Optical media drives
i.LINK uses a four-pin connector, which does not carry electric current.
External devices will need their own power supply.
Precautions
■ Make a back-up of your data before transferring it to the computer.
There is a possibility that the original data will be damaged. There is a
particular risk that some frames will be deleted in the case of digital
video transfer.
■ Do not transfer data in areas where static electricity is easily generated
or in areas subjected to electronic noise. Data can be destroyed.
■ If you are transferring data through an IEEE1394 hub, do not connect or
disconnect other devices from the hub during data transfer. There is a
likelihood that data will be damaged. Connect all devices to the hub
before you turn on the computer's power.
Connecting
1. Make sure the connectors are properly aligned and plug the i.LINK
(IEEE1394) cable into the computer.
2. Plug the other end of the cable into the device.
Note the following when you use i.LINK:
■ You may need to install drivers for your i.LINK devices.
■ Not all i.LINK devices have been tested. Therefore, compatibility with all
i.LINK devices cannot be guaranteed.
■ Use S100, S200 or S400 cables no longer than three meters.
■ Some devices might not support standby or automatic off functions.
■ Do not connect or disconnect an i.LINK device while it is using an
application or when the computer is automatically shutting it down to
save power. Data might be destroyed.
Disconnecting
1. Click the Eject or Remove Hardware icon on the Task Bar.
2. Point to i.LINK (IEEE1394) device and click.
3. Disconnect the cable from the computer then from the i.LINK device.
Refer also to the documentation that came with your i.LINK device.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-14
Optional Devices
Security lock
A security lock enables you to anchor your computer to a desk or other
heavy object to help prevent unauthorized removal of the computer.
Attach one end of a cable to the desk and the other end to the security lock
slot on the right side of the computer.
Security lock
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7-15
Satellite P30 Series
Chapter 8
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems
occur, following the procedures in this chapter can help to determine the
cause.
All readers should become familiar with this chapter. Knowing what might
go wrong can help prevent problems from occurring.
Problem solving process
Resolving problems will be much easier if you observe the following
guidelines:
■ Stop immediately when you recognize a problem exists. Further action
may result in data loss or damage. You may destroy valuable
problem-Related information that can help solve the problem.
■ Observe what is happening. Write down what the system is doing and
what actions you performed immediately before the problem occurred.
If you have a printer attached, print a copy of the screen using PrtSc.
■ Isolate the problem. Using the tools available to you, such as the
troubleshooting tips in this chapter, try to discover the specific actions
that caused the problem.
The questions and procedures offered in this chapter are meant as a guide,
they are not definitive problem solving techniques. Many problems can be
solved simply, but a few may require help from your dealer. If you find you
need to consult your dealer or others, be prepared to describe the problem
in as much detail as possible.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-1
Troubleshooting
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to
fix and yet can cause what appears to be a serious problem.
■ Make sure you turn on all peripheral devices before you turn on the
computer.
This includes your printer and any other external device you are using.
■ Before you attach an external device, turn the computer off. When you
turn the computer back on it recognizes the new device.
■ Make sure all options are set properly in the setup program.
■ Check all cables. Are they correctly and firmly attached? Loose cables
can cause signal errors.
■ Inspect all connecting cables for loose wires and all connectors for
loose pins.
■ Check that your diskette, CD-ROM or DVD-ROM is correctly inserted
and that the diskette’s write protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log.
This will help you describe your problems to your dealer. If a problem
recurs, the log will help you identify the problem faster.
Analyzing the problem
Sometimes the system gives clues that can help you identify why it is
malfunctioning. Keep the following questions in mind:
■ Which part of the system is not operating properly: keyboard, diskette
drives, hard disk drive, printer, display. Each device produces different
symptoms.
■ Is the operating system configuration set properly? Check the
configuration options.
■ What appears on the display screen? Does it display any messages or
random characters? Print a copy of the screen if you have a printer
attached. Look up the messages in the software and operating system
documentation. Check that all connecting cables are correctly and
firmly attached. Loose cables can cause erroneous or intermittent
signals.
■ Do any indicators light? Which ones? What color are they? Do they stay
on or blink? Write down what you see.
■ Do you hear any beeps? How many? Are they long or short? Are they
high pitched or low? Is the computer making any unusual noises? Write
down what you hear.
Record your observations so you can describe them to your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-2
Troubleshooting
Software
The problems may be caused by your software
or diskette. If you cannot load a software
package, the media may be damaged or the
program might be corrupted. Try loading another
copy of the software.
If an error message appears while you are using
a software package, check the software
documentation. These documents usually
include a problem solving section or a summary
of error messages.
Next, check any error messages in the OS
documentation.
Hardware
If you cannot find a software problem, check your
hardware. First run through the items in the
preliminary checklist above. If you still cannot
correct the problem, try to identify the source.
The next section provides checklists for
individual components and peripherals.
Hardware and system checklist
This section discusses problems caused by your computer’s hardware or
attached peripherals. Basic problems may occur in the following areas:
■ System start-up
■ Self test
■ PC Card
■ Printer
■ Power
■ Monitor
■ Overheating power down
■ AC Power
■ Battery
■ Sound system
■ Pointing device
■ USB
■ Password
■ LAN
■ Keyboard
■ LCD panel
■ Hard disk drive
■ Memory cards
■ Wireless LAN
■ Standby/Hibernation
■ Memory expansion
■ Modem
■ i.LINK (IEEE1394)
■ DVD Super Multi drive
■ DVD±R/±RW (DVD Dual) drive ■ Diskette drive
■ CD-RW/DVD-ROM drive
■ Real Time Clock
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-3
Troubleshooting
System start-up
When the computer does not start properly, check the following items:
■ Self Test
■ Power Sources
■ Power-on Password
Self test
When the computer starts up, the self test will be run automatically, and the
following will be displayed:
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating
system.
Depending on how the Boot Priority is set in the computer’s BIOS.
If any of the following conditions are present, the self test failed:
■ The computer stops and does not proceed to display information or
messages except the TOSHIBA logo.
■ Random characters appear on the screen, and the system does not
function normally.
■ The screen displays an error message.
Turn off the computer and check all cable connections as well as PC Card
and memory module connections. If the test fails again, contact your
dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-4
Troubleshooting
Power
When the computer is not plugged into an AC outlet, the battery pack is the
primary power source. However, your computer has a number of other
power resources, including intelligent power supply, Real Time Clock
battery. These resources are interrelated and any one could affect apparent
power problems. This section provides check lists for AC power and the
battery. If you cannot resolve a problem after following them, the cause
could lie with another power resource. In such case, contact your dealer.
Overheating power down
If the computer’s internal temperature becomes too high, the computer will
automatically shut down.
AC power
If you have trouble turning on the computer with the AC adaptor connected,
Modes, for more information.
Problem
Procedure
AC adaptor doesn't
power the computer
Check the connections. Make sure the cord is
firmly connected to the computer and a power
(DC IN indicator does outlet.
not glow green).
Check the condition of the cord and terminals. If
the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the AC adaptor still does not power the
computer, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-5
Troubleshooting
Battery
If you suspect a problem with the battery, check the DC IN indicator as well
as the indicators for the battery. For information on indicators and battery
Problem
Procedure
Battery doesn't power The battery may be discharged. Connect the AC
the computer. power cord to charge the battery.
Battery doesn't charge If the battery is completely discharged, it will not
when the AC power
begin charging at once. Wait a few minutes.
cord is attached.
(Battery indicator does
not glow amber.)
If the battery still does not charge, make sure the
outlet is supplying power. Plug in an appliance
and see if it works. If it doesn't, try another
power source.
Check whether the battery is hot or cold. If the
battery is too hot or too cold, it will not charge
properly. Let it reach room temperature.
Unplug the AC adaptor and remove the battery
to make sure the terminals are clean. If
necessary wipe them with a soft dry cloth dipped
in alcohol.
Connect the AC adaptor and replace the battery.
Check the Battery indicator. If it does not glow,
let the computer charge the battery for at least
20 minutes. If the Battery indicator glows after
20 minutes, let the battery continue to charge for
at least another 20 minutes before turning on the
computer.
If the indicator still does not glow, the battery
may be at the end of its operating life.
Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn't power Check the power consumption settings in the
the computer as long
as expected.
TOSHIBA Power Saver utility. Consider using a
power saving mode.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-6
Troubleshooting
Keyboard
Keyboard problems can be caused by your setup configuration. For more
Problem
Procedure
Some letter keys
produce numbers.
Check that the numeric keypad overlay is not
selected. Press Fn + F10 and try typing again.
Output to screen is
garbled.
Make sure the software you are using is not
remapping the keyboard. Remapping involves
reassigning the meaning of each key. See your
software's documentation.
If you are still unable to use the keyboard,
consult your dealer.
LCD panel
Problem
Procedure
Lines appear broken.
Check if you are in DOS mode. In DOS, lines
may appear broken, because of the LCD
screen's higher resolution. The Windows display
should appear normal.
No display
Press hotkeys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
Make sure instant security was not activated. Try
entering your password, if you have one
registered. Or, turn the power off and back on to
clear instant security .
Problems above
remain unresolved or
Refer to your software's documentation to
determine if the software is causing the difficulty.
other problems occur.
Contact your dealer if the problems continue.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-7
Troubleshooting
Hard disk drive
Problem
Procedure
Computer does not
Insert a system diskette and reboot.
boot from hard drive.
There may be a problem with your operating
system files. Refer to your OS documentation.
Slow performance
Your files may be fragmented. Run SCANDISK
and defragmenter to check the condition of your
files and disk. Refer to your OS documentation
or online HELP for information on running
SCANDISK and the defragmenter.
Contact your dealer if the problems continue.
CD-RW/DVD-ROM drive
Problem
Procedure
You cannot access a
CD/DVD in the drive.
Make sure the drive's drawer is securely.
Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. Refer to Media care section in
cleaning.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-8
Troubleshooting
Problem
Procedure
The software or hardware configuration may be
Some CD/DVDs run
correctly, but others do causing a problem. Make sure the hardware
not.
configuration matches your software's needs.
Check the CD/DVD's documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM: DVD-ROM, DVD-Video
CD-ROM:
CD-DA, CD-Text, Photo CD™
(single/multi-session), CD-ROM
Mode 1, Mode 2, CD-ROM XA
Mode 2 (Form1, Form2),
Enhanced CD (CD-EXTRA), CD-
G (Audio CD only), Addressing
Method 2
Recordable: CD-R, CD-RW, CD
Check the region code on the DVD. It must
match that on the CD-RW/DVD-ROM drive.
Region codes are listed in the Optical media
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA.
■ Do not use the mouse or keyboard during
writing.
■ Use only the software supplied with the
computer for recording.
■ Do not run or start other software during
writing.
■ Do not jar the computer during writing.
■ Do not connect/ disconnect external devices
or install/remove internal cards during writing.
If problems persist, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-9
Troubleshooting
DVD±R/±RW drive (DVD Dual Drive)
Problem
Procedure
Some CD run correctly, The software or hardware configuration may be
but others do not.
causing a problem. Make sure the hardware
configuration matches your software's needs.
Check the CD/DVD's documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM: DVD-ROM, DVD-Video, DVD-R,
DVD-RW, DVD+R, DVD+RW
CD-ROM:
CD-DA, CD-Text, Photo CD
(single/multi-session), CD-ROM
Mode 1, Mode 2, CD-ROM XA
Mode 2 (Form1, Form2),
Enhanced CD (CD-EXTRA), CD-
G (Audio CD only), Addressing
Method 2
Check the region code on the DVD. It must
match that on the DVD±RW drive.
You cannot access a
CD/DVD in the drive.
Make sure the drive's drawer is securely closed.
Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in
cleaning.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-10
Troubleshooting
Problem
Procedure
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA.
■ Do not use the mouse or keyboard during
writing.
■ Use only the software supplied with the
computer for recording.
■ Do not run or start other software during
writing.
■ Do not jar the computer during writing.
■ Do not connect/ disconnect external devices
or install/remove internal cards during writing.
If problems persist, contact your dealer.
DVD Super Multi drive
Problem
Procedure
You cannot access a
CD/DVD in the drive.
Make sure the drive's drawer is securely closed.
Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facing up.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in
cleaning.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-11
Troubleshooting
Problem
Procedure
Some CD run correctly, The software or hardware configuration may be
but others do not.
causing a problem. Make sure the hardware
configuration matches your software's needs.
Check the CD/DVD's documentation.
Check the type of CD/DVD you are using. The
drive supports:
DVD-ROM: DVD-ROM, DVD-Video, DVD-R,
DVD-RW, DVD+R, DVD+RW,
DVD-RAM
CD-ROM:
CD-DA, CD-Text, Photo CD
(single/multi-session), CD-ROM
Mode 1, Mode 2, CD-ROM XA
Mode 2 (Form1, Form2),
Enhanced CD (CD-EXTRA), CD-
G (Audio CD only), Addressing
Method 2
Check the region code on the DVD. It must
match that on the DVD±RW drive.
Cannot write correctly If you have trouble writing, make sure you are
observing the following precautions:
■ Use only media recommended by TOSHIBA.
■ Do not use the mouse or keyboard during
writing.
■ Use only the software supplied with the
computer for recording.
■ Do not run or start other software during
writing.
■ Do not jar the computer during writing.
■ Do not connect/ disconnect external devices
or install/remove internal cards during writing.
If problems persist, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-12
Troubleshooting
Diskette drive
Problem
Procedure
Some programs run
The software or hardware configuration may be
correctly, but others do causing a problem. Make sure the hardware
not. configuration match's your software's needs.
You cannot access the Try another disk. If you can access this disk, the
diskette drive probably original disk (not the disk drive) is problem.
causing the.
If problems persist, contact your dealer.
Sound system
Refer also to documentation for your audio devices.
Problem
Procedure
Adjust the volume control dial.
No sound is heard.
Check the software volume settings.
Make sure the headphone connection is secure.
If problems persist, contact your dealer.
Annoying sound
You may be experiencing feedback. Refer to
is heard.
If problems persist, contact your dealer.
PC Card
Problem Procedure
PC Card error occurs. Reseat the PC Card to make sure it is firmly
connected.
Make sure the connection between the external
device and the card is firm.
Check the card's documentation.
If problems persist, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-13
Troubleshooting
Memory cards
Problem
Procedure
Memory card error
occurs.
Reseat the memory card to make sure it is firmly
connected.
Check the card's documentation.
If problems persist, contact your dealer.
Pointing device
If you are using a USB mouse, also refer to the USB section in this chapter
and to your mouse documentation.
Touch pad
Problem
Procedure
On-screen pointer
does not respond to
Pad operation.
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume its
normal shape and try again to move it. You may
also press Fn + F9 to enable the Touch Pad and
then try again to move it.
Double-tapping does
not work.
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
The mouse pointer
moves too fast or too
slow.
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
If problems persist, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-14
Troubleshooting
USB mouse
Problem
Procedure
On-screen pointer
does not respond to
Pad operation.
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume its
normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
Double-tapping does
not work.
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
The mouse pointer
moves too fast or too
slow.
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
The mouse pointer
moves erratically.
The mouse might be dirty. Refer to your mouse
documentations for instructions on cleaning.
If problems persist, contact your dealer.
USB
Refer also to your USB device’s documentation.
Problem
Procedure
USB device does not
work.
Check for a firm cable connection between the
USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows documentation
for information on checking the drivers.
If problems persist, contact your dealer.
User’s Manual
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Standby/Hibernation
Problem
Procedure
The system will not
enter Standby/
Hibernation.
Is Windows Media™ Player open? The system
might not enter Standby/Hibernation, if Windows
Media Player is either playing a selection or
finished playing a selection. Close Windows
Media Player before you select Standby/
Hibernation.
If problems persist, contact your dealer.
Real Time Clock
Problem
Procedure
The following
The battery for RTC is wearing. Set the date and
message is Displayed time in BIOS setup with the following steps:
on the LCD:
1. Press [F1] key. BIOS setup will boot up.
RTC battery is low or
CMOS checksum is
inconsistent. Press
2. Press [F2] to set the date in [System Date].
3. Press [F2] to set the time in [System Time].
[F2] key to set Date/
Time.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-16
Troubleshooting
Memory expansion
memory modules.
Problem
Procedure
The computer hangs
up and issues beep
sounds. (A long leep,
three short beeps,
three short beeps, and
then a long beep.)
Make sure the memory module installed in the
expansion slot is compatible with the computer.
If an incompatible module has been installed,
follow the steps below.
1. Turn off the power.
2. Disconnect the AC adaptor and all periph-eral
devices.
3. Remove the battery pack.
4. Remove the memory module.
5. Replace the battery pack and/or connect the
AC adaptor.
6. Turn on the power.
If problems persist, contact your dealer.
Modem
Problem
Procedure
Communication
Make sure the computer's internal modem
software can't initialize settings are correct. Refer to Phone and Modem
Options Properties in the Control Panel.
the modem.
You can hear a dial
tone but can't make a
call.
If the call is going through a PBX machine, make
sure the communication application's tone dial
detection feature is disabled.
You place a call, but a Make sure the settings are correct in your
connection can't be
communications application.
made.
After making a call you Make sure the tone or pulse selection in your
communications application is set correctly.
can't hear a ring.
Communication is cut The computer will automatically cut off
communication when connection with the carrier
is not successful for a set time interval. Try
lengthening this time interval.
off unexpectedly.
A CONNECT display is Check the error control setting in your
quickly replaced by NO communications application.
CARRIER.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-17
Troubleshooting
Problem
Procedure
Character display
becomes garbled
during a
In data transmission, make sure the parity bit
and stop bit settings correspond with those of
the remote computer.
communication.
Check the flow control and communication
protocol.
You cannot receive an Check the "rings before auto answer" setting in
your communications application.
incoming call.
If problems persist, contact your dealer.
LAN
Problem
Procedure
Cannot access LAN
Check for a firm cable connection between the
LAN jack and the Wake LAN HUB.
up on LAN does not
Make sure the AC adaptor is connected. You
cannot access a LAN using the computer's
battery power.
work.
If problems persist, consult your LAN
administrator.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN
administrator. For more information on wireless communication, refer to
Problem
Procedure
Cannot access
Wireless LAN
Make sure the computer's wireless
communication switch is set to on.
Use the Config Free program that comes pre-
installed in your computer to see LAN status.
If problems persist, consult your LAN
administrator.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-18
Troubleshooting
Monitor
documentation.
Problem
Procedure
Monitor does not turn
on.
Make sure that the external monitor's power
switch is on. Confirm that the external monitor's
power cable is plugged into a working power
outlet.
No display
Try adjusting the contrast and brightness
controls on the external monitor.
Press hotkeys Fn + F5 to change the display
priority and make sure it is not set for the internal
display.
Check that the cable connecting the external
monitor to the computer is attached firmly.
Display error occurs.
If problems persist, contact your dealer.
i.LINK (IEEE1394)
Problem
Procedure
i.LINK device does not Make sure the cable is securely connected to
the computer and to the device.
function.
Make sure the device's power is turned on.
Reinstall the drivers. Open the Windows Control
Panel and double-click the Add New Hardware
icon. Follow the on-screen directions.
Restart Windows.
If problems persist, contact your dealer.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-19
Troubleshooting
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for
additional technical assistance.
Before you call
Some problems you experience may be related to software or the operating
system, it is important to investigate other sources of assistance first.
Before contacting TOSHIBA, try the following:
■ Review troubleshooting sections in the documentation for software and
peripheral devices.
■ If a problem occurs when you are running software applications, consult
the software documentation for troubleshooting suggestions. Call the
software company’s technical support for assistance.
■ Consult the dealer you purchased your computer and/or software from.
They are your best sources for current information and support.
Where to write
If you are still unable to solve the problem and suspect that it is hardware
related, write to TOSHIBA at the location listed in the accompanying
warrantly booklet or visit www.toshiba-europe.com on the internet.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8-20
Satellite P30 Series
Appendix A
Specifications
This appendix summarizes the computer's technical specifications.
Dimensions
420mm x 293mm x 39.9mm (Front)/47mm (Rear)
Weight
4.3kg/9.49lbs
(Actual weight may vary depending on configuration.)
Environmental Requirements
Conditions
Operating
Ambient temperature
Relative humidity
5°C to 30°C
20% to 80%
Non-operating
Conditions
Operating
-20°C to 65°C
Altitude (from sea level)
sea level to 10,000 meters
sea level to 40,000 meters
Non-operating
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
Specifications
Built-in Modem
Network control unit (NCU)
Type of NCU
Type of line
AA
Telephone line (analog only)
Type of dialing
Pulse
Tone
Control command
Monitor function
AT commands
EIA-578 commands
Computer's speaker
Communication specifications
Communication
System
Data:
Fax:
Full duplex
Half duplex
Communication
Protocol
Data:
ITU-T-Rec
(Former CCITT)
V.21/V.22/V.22bis/V.32/
V.32bis/V.34/V.90/
V.92(only for USA and
Canada)
Bell
103/212A
Fax:
ITU-T-Rec
(Former CCITT)
V.17/V.29/V.27ter /V.21
ch2
Communication
Speed
Data transmission and reception
300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600 bps
Data reception only with V.90/V.92
28000/29333/30666/32000/33333/34666/36000/
37333/38666/40000/41333/42666/44000/45333/
46666/48000/49333/50666/52000/53333/54666/
56000 bps
Fax
2400/4800/7200/9600/12000/14400 bps
Error correcting
MNP class 4 and ITU-T V.42
Data compression
MNP class 5 and ITU-T V.42bis
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
Satellite P30 Series
Appendix B
Display Modes
This appendix contains a table listing all the display modes currently
supported by the ATI Mobility Radeon graphics controller.
CRT Display
Resolution
Color Depth
(bpp)
Refresh Rate
(Hz)
800 x 600
16 bpp
32 bpp
16 bpp
32 bpp
16 bpp
32 bpp
16 bpp
32 bpp
16 bpp
32 bpp
16 bpp
32 bpp
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85, 100
60, 75, 85
1024 x 768
1280 x 1024
1600 x 1200
1920 x 1440
2048 x 1536
60, 75, 85
60
60
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-1
Display Modes
Displaying movies on a TV or CRT
This section describes how to set up your system to display movies
simultaneously on your computer's LCD and on an external TV or CRT
monitor.
Follow the steps below.
1. Open the Control Panel and click Appearance and Themes.
2. Click Display.
3. Select the Settings tab and click Advanced.
4. Click the Displays tab.
5. Select the external display device you wish to use. It must be connected
to the computer in order to be selected from the menu here.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
Display Modes
6. In the resulting properties box, if any additional options are available for
your particular device, set then to your liking.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-3
Display Modes
7. Finally, click the ATI Overlay tab to adjust the video overlay properties.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
B-4
Satellite P30 Series
Appendix C
Power Cable Connectors
The Satellite computer features a universal power supply you can use
worldwide. This appendix shows the configuration of typical AC power cord
plugs and sockets in various parts of the world.
The following illustrations show the plug shapes for the U.S.A. and Canada,
the United Kingdom, Australia and Europe
USA and Canada
United Kingdom
BS approved
UL approved
CSA approved
Europe
Australia
AS approved
Approved by the
appropriate agency
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
C-1
Satellite P30 Series
Appendix D
If your computer is stolen
Always take care of your computer and try to prevent it from being stolen.
You are the owner of a valuable technical device, which may be highly
attractive to thieves, so please do not leave it unattended in a public place.
To further help protect against theft, security cables can be bought for use
with your notebook when it is being used at home or in the office.
Make a note of your computer’s machine type, model number, and serial
number, and put it in a safe place. You will find this information on the
underside of your notebook. Please also keep the receipt of the computer
you purchased.
Should your computer be stolen, however, we’ll help you try to find it.
Before contacting TOSHIBA, please prepare the following information
which is necessary to uniquely identify your computer:
■ In which country was your computer stolen?
■ What type of machine do you have?
■ What was the model number (PA number)?
■ What was the serial number (8 digits)?
■ When was it stolen, i.e. date?
■ What is your address, phone, and fax number?
To register the theft on paper, please follow these procedures:
■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below.
■ Attach a copy of your receipt showing where your computer was
purchased.
■ Either fax or send the receipt and registration form to the address
below.
To register the theft online, please follow these procedures:
■ Visit www.toshiba-europe.com on the Internet. In the product area,
choose Computer Systems.
■ In the Computer Systems page, open the Support & Downloads menu
and choose the Stolen Units Database option.
Your entries are used to track your computer at our service points.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
If your computer is stolen
TOSHIBA Theft Registration
Send to:
TOSHIBA Europe GmbH
Technical Service and Support
Leibnizstr. 2
93055 Regensburg
Germany
Fax number:
+49 (0) 941 7807 921
Country stolen:
Machine type:
(e.g. Satellite A50)
Model number:
(e.g. PSA50 YXT)
Serial number:
(e.g. 12345678G)
Date stolen:
Year
Month
Day
Owner’s details
Last name, first name:
Company:
Street:
Postal Code/City:
Country:
Phone:
Fax:
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
D-2
Satellite P30 Series
Glossary
The terms in this glossary cover topics related to this manual.
Alternate naming is included for reference.
Abbreviations
AC: alternating current
AGP: accelerated graphics port
ASCII: American Standard Code for Information Interchange
BIOS: basic input output system
CD-ROM: Compact Disc-Read Only Memory
CD-RW: Compact Disc-Read/Write
CMOS: complementary metal-oxide semiconductor
CPU: central processing unit
CRT: cathode ray tube
DC: direct current
DDC: display data channel
DMA: direct memory access
DOS: disk operating system
DVD: digital versatile disc
ECP: extended capabilities port
FDD: floppy disk drive
FIR: fast infrared
HDD: hard disk drive
IDE: integrated drive electronics
I/O: input/output
IrDA: Infrared Data Association
IRQ: interrupt request
KB: kilobyte
LCD: liquid crystal display
LED: light emitting diode
LSI: large scale integration
MS-DOS: Microsoft Disk Operating System
PCI: peripheral component interconnect
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-1
Glossary
RAM: random access memory
ROM: read only memory
RTC: real time clock
SCSI: small computer system interface
TFT: thin-film transistor
USB: Universal Serial Bus
VESA: Video Electronic Standards Association
VGA: video graphics array
XGA: extended graphics array
A
adaptor: A device that provides an interface between two dissimilar
electronic devices. For example, the AC adaptor modifies the power
from a wall outlet for use by the computer. This term also refers to
the add-in circuit cards that control external devices, such as video
monitors and magnetic tape devices.
application: A group of programs that together are used for a specific task
such as accounting, financial planning, spreadsheets, word
processing and games.
ASCII: American Standard Code for Information Interchange. ASCII code
is a set of 256 binary codes that represent the most commonly used
letters, numbers, and symbols.
B
BIOS: Basic Input Output System. The firmware that controls data flow
within the computer. See also firmware.
bit: Derived from "binary digit," the basic unit of information used by the
computer. It is either zero or one. Eight bits is one byte. See also
byte.
boot: Short for bootstrap. A program that starts or restarts the computer.
The program reads instructions from a storage device into the
computer’s memory.
bps: Bits per second. Typically used to describe the data transmission
speed of a modem.
buffer: The portion of the computer’s memory where data is temporarily
stored. Buffers often compensate for differences in the rate of flow
from one device to another.
bus: An interface for transmission of signals, data or electric power.
byte: The representation of a single character. A sequence of eight bits
treated as a single unit; also the smallest addressable unit within the
system.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-2
Glossary
C
cache memory: High speed memory which stores data that increases
processor speed and data transfer rate. When the CPU reads data
from main memory, it stores a copy of this data in cache memory.
The next time the CPU needs that same data, it looks for it in the
cache memory rather than the main memory, which saves time. The
computer has two cache levels. Level one is incorporated into the
processor and level two resides in external memory.
capacity: The amount of data that can be stored on a magnetic storage
device such as a floppy disk or hard disk. It is usually described in
terms of kilobytes (KB), where one KB = 1024 bytes and megabytes
(MB), where one MB = 1024 KB.
CardBus: An industry standard bus for 32-bit PC cards.
CD-ROM: A Compact Disc-Read Only Memory is a high capacity disc that
can be read from but not written to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read data from the disc.
CD-R: A Compact Disc-Recordable disc can be written once and read
many times. See also CD-ROM.
CD-RW: A Compact Disc-Read/Write disc can be rewritten many times.
See also CD-ROM.
character: Any letter, number, punctuation mark, or symbol used by the
computer. Also synonymous with byte.
chip: A small semiconductor containing computer logic and circuitry for
processing, memory, input/output functions and controlling other
chips.
CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit
fabricated on a silicon wafer that requires very little power.
Integrated circuits implemented in CMOS technology can be tightly
packaged and are highly reliable.
compatibility: 1) The ability of one computer to accept and process data
in the same manner as another computer without modifying the data
or the media upon which it is being transferred.
2) the ability of one device to connect to or communicate with
another system or component.
components: Elements or parts (of a system) which make up the whole
(system).
configuration: The specific components in your system (such as the
terminal, printer, and disk drives) and the settings that define how
your system works. You use the HW Setup program to control your
system configuration.
control keys: A key or sequence of keys you enter from the keyboard to
initiate a particular function within a program.
controller: Built-in hardware and software that controls the functions of a
specific internal or peripheral device (e.g. keyboard controller).
CPU: Central Processing Unit. The portion of the computer that interprets
and executes instructions.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-3
Glossary
CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a
fluorescent screen-producing luminous spots. An example is the
television set.
cursor: A small, blinking rectangle or line that indicates the current
position on the display screen.
D
DC: Direct Current. Electric current that flows in one direction. This type of
power is usually supplied by batteries.
default: The parameter value automatically selected by the system when
you or the program do not provide instructions. Also called a preset
value.
device driver: A program that controls communication between a specific
peripheral device and the computer. The CONFIG.SYS file contains
device drivers that MS-DOS loads when you turn the computer on.
dialog box: A window that accepts user input to make system settings or
record other information.
disk drive: The device that randomly accesses information on a disk and
copies it to the computer’s memory. It also writes data from memory
to the disk. To accomplish these tasks, the unit physically rotates the
disk at high speed past a read-write head.
display: A CRT, LCD, or other image producing device used to view
computer output.
DOS: Disk Operating System. See operating system.
driver: A software program, generally part of the operating system, that
controls a specific piece of hardware (frequently a peripheral device
such as a printer or mouse).
DVD-RAM: A Digital Versatile Disc Random Access Memory is a high-
capacity, high performance disc that lets you store large volumes of
data. The DVD-ROM drive uses a laser to read data from the disc.
DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity,
high performance disc suitable for play back of video and other
high-density files. The DVD-ROM drive uses a laser to read data
from the disc.
E
execute: To interpret and execute an instruction.
F
fast infrared: An industry standard that enables cableless infrared serial
data transfer at speeds of up to 4 Mbps.
floppy disk: A removable disk that stores magnetically encoded data.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-4
Glossary
floppy disk drive (FDD): An electromechanical device that reads and
writes to floppy disks.
folder: An icon in Windows used to store documents or other folders.
format: The process of readying a blank disk for its first use. Formatting
establishes the structure of the disk that the operating system
expects before it writes files or programs onto the disk.
function keys: The keys labeled F1 through F12 that tell the computer to
perform certain functions.
G
gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also
megabyte.
graphics: Drawings, pictures, or other images, such as charts or graphs, to
present information.
H
hard disk: A non-Removable disk usually referred to as drive C. The
factory installs this disk and only a trained engineer can remove it
for servicing. Also called fixed disk.
hard disk drive (HDD): An electromechanical device that reads and writes
a hard disk. See also hard disk.
hertz: A unit of wave frequency that equals one cycle per second.
hot key: The computer’s feature in which certain keys in combination with
the extended function key, Fn, can be used to set system
parameters, such as speaker volume.
I
i.LINK (IEEE1394): This port enables high-speed data transfer directly
from external devices such as digital video cameras.
input: The data or instructions you provide to a computer, communication
device or other peripheral device from the keyboard or external or
internal storage devices. The data sent (or output) by the sending
computer is input for the receiving computer.
interface: 1) Hardware and/or software components of a system used
specifically to connect one system or device to another.
2) To physically connect one system or device to another to
exchange information.
3) The point of contact between user, the computer, and the
program, for example, the keyboard or a menu.
I/O: Input/output. Refers to acceptance and transfer of data to and from a
computer.
I/O devices: Equipment used to communicate with the computer and
transfer data to and from it.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-5
Glossary
IrDA 1.1: An industry standard that enables cableless infrared serial data
transfer at speeds of up to 4 Mbps.
J
jumper: A small clip or wire that allows you to change the hardware
characteristics by electrically connecting two points of a circuit.
K
K: Taken from the Greek word kilo, meaning 1000; often used as
equivalent to 1024, or 2 raised to the 10th power. See also byte and
kilobyte.
KB: See kilobyte.
L
Light Emitting Diode (LED): A semiconductor device that emits light
when a current is applied.
Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets
of glass coated with transparent conducting material. The viewing-
side coating is etched into character forming segments with leads
that extend to the edge of the glass. Applying a voltage between the
glass sheets alters the brightness of the liquid crystal.
LSI: Large Scale Integration.
1) A technology that allows the inclusion of up to 100,000 simple
logic gates on a single chip.
2) An integrated circuit that uses large scale integration.
M
megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also
kilobyte.
mode: A method of operation, for example, the boot mode, standby mode
or the hibernation mode.
modem: Derived from modulator/demodulator, a device that converts
(modulates) digital data for transmission over telephone lines and
then converts modulated data (demodulates) to digital format where
received.
monitor: A device that uses rows and columns of pixels to display
alphanumeric characters or graphic images. See also CRT.
MP3: An audio compression standard that enables high-quality
transmission and real-time playback of sound files.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-6
Glossary
N
numeric keypad overlay: A feature that allows you to use certain keys on
the keyboard to perform numeric entry, or to control cursor and page
movement.
O
operating system: A group of programs that controls the basic operation
of a computer. Operating system functions include interpreting
programs, creating data files, and controlling the transmission and
receipt (input/output) of data to and from memory and peripheral
devices.
output: The results of a computer operation. Output commonly indicates
data.
1) printed on paper, 2) displayed at a terminal, 3) sent through the
serial port of internal modem, or 4) stored on some magnetic media.
P
parity: 1) The symmetrical relationship between two parameter values
(integers) both of which are either on or off; odd or even; 0 or 1.
2) In serial communications, an error detection bit that is added to a
group of data bits making the sum of the bits even or odd. Parity can
be set to none, odd, or even.
peripheral device: An I/O device that is external to the central processor
and/or main memory such as a printer or a mouse.
pixel: A picture element. The smallest dot that can be made on a display
or printer. Also called a pel.
plug and play: A capability with Windows that enables the system to
automatically recognize connections of external devices and make
the necessary configurations in the computer.
port: The electrical connection through which the computer sends and
receives data to and from devices or other computers.
prompt: A message the computer provides indicating it is ready for or
requires information or an action from you.
R
Random Access Memory (RAM): High speed memory within the
computer circuitry that can be read or written to.
restart: Resetting a computer without turning it off (also called “warm boot”
or “soft reset”). See also boot.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-7
Glossary
ROM: Read Only Memory: A nonvolatile memory chip manufactured to
contain information that controls the computer’s basic operation.
You cannot access or change information stored in ROM.
S
SCSI: Small Computer System Interface is an industry standard interface
for connection of a variety of peripheral devices.
soft key: Key combinations that emulate keys on the IBM keyboard,
change some configuration options, stop program execution, and
access the numeric keypad overlay.
stop bit: One or more bits of a byte that follow the transmitted character or
group codes in asynchronous serial communications.
system disk: A disk that has been formatted with an operating system.
For MS-DOS the operating system is contained in two hidden files
and the COMMAND.COM file. You can boot a computer using a
system disk. Also called an operating system disk.
T
terminal: A typewriter-like keyboard and CRT display screen connected to
the computer for data input/output.
TFT display: A liquid crystal display (LCD) made from an array of liquid
crystal cells using active-matrix technology with thin film transistor
(TFT) to drive each cell.
Touch Pad: A pointing device integrated into the TOSHIBA computer palm
rest.
U
Universal Serial Bus: This serial interface lets you communicate with
several devices connected in a chain to a single port on the
computer.
V
VGA: Video Graphics Array is an industry standard video adaptor that lets
you run any popular software.
W
warm start: Restarting or resetting a computer without turning it off.
write protection: A method for protecting a floppy disk from accidental
erasure.
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-8
|