Form No. 3354-969
LX420 & LX460 Lawn Tractors
Model No. 13AX60RG744
Model No. 13AX60RH744
Original Instructions (EN)
769-02247F (01/11/06)
Register your product at www.Toro.com
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: This symbol points out important safety instructions which, if not followed, could endanger
the personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol–heed its warning.
DANGER: This machine was built to be operated according to the rules for safe operation in this man-
ual. As with any type of power equipment, carelessness or error on the part of the operator can result in
serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to
observe the following safety instructions could result in serious injury or death.
WARNING: This unit is equipped with an internal combustion engine and should not be used on or near
any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system
is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used,
it should be maintained in effective working order by the operator. In the State of California the above is
required by law (Section 4442 of the California Public Resources Code). Other states may have similar
laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your Toro
service dealer or contact Toro at 8111 Lyndale Avenue South, Bloomington, IN 55420-0019.
California Proposition 65 Warning:
WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain
or emit chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
during operation and while performing an
GENERAL OPERATION
adjustment or repair to protect your eyes. Thrown
1. Read, understand, and follow all instructions on the
objects which ricochet can cause serious injury to
machine and in the manual(s) before attempting to
the eyes.
assemble and operate. Keep this manual in a safe
9. Wear sturdy, rough-soled work shoes and close-
place for future and regular reference.
fitting slacks and shirts. Loose fitting clothes and
2. Be familiar with all controls and their proper
jewelry can be caught in movable parts. Never
operation. Know how to stop the machine and
operate this machine in bare feet or sandals.
disengage PTO/blades quickly.
10. Be aware of the mower and attachment discharge
3. Never allow children under 14 years old to operate
direction and do not point it at anyone. Do not
this machine. Children 14 years old and over
operate the mower without the discharge cover or
should read and understand the operation
entire grass catcher in its proper place.
instructions and safety rules in this manual and
11. Do not put hands or feet near rotating parts or
should be trained and supervised by a parent or
under the cutting deck. Contact with the blade(s)
responsible adult.
can amputate hands and feet.
4. Never allow adults to operate this machine without
12. A missing or damaged discharge cover can cause
proper instruction.
blade contact or thrown object injuries.
5. To help avoid blade contact or a thrown object
13. Stop the blade(s) when crossing gravel drives,
injury, keep bystanders, helpers, children and pets
walks, or roads and while not cutting grass.
at least 75 feet from the machine while it is in
14. Watch for traffic when operating near or crossing
operation. Stop machine if anyone enters the area.
roadways. This machine is not intended for use on
6. Thoroughly inspect the area where the equipment
any public roadway.
is to be used. Remove all stones, sticks, wire,
15. Do not operate the machine while under the
bones, toys, and other foreign objects which could
influence of alcohol or drugs.
be picked up and thrown by the blade(s). Thrown
16. Mow only in daylight or good artificial light.
objects can cause serious personal injury.
17. Never carry passengers.
7. Plan your mowing pattern to avoid discharge of
18. Disengage blade(s) before shifting into reverse.
material toward roads, sidewalks, bystanders and
Back up slowly. Always look down and behind
the like. Also, avoid discharging material against a
before and while backing to avoid a back-over
wall or obstruction which may cause discharged
accident.
material to ricochet back toward the operator.
8. Always wear safety glasses or safety goggles
3
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Slow down before turning. Operate the machine
smoothly. Avoid erratic operation and excessive
speed.
20. Disengage blade(s), set parking brake, stop engine
and wait until the blade(s) come to a complete stop
before removing grass catcher, emptying grass,
unclogging chute, removing any grass or debris, or
making any adjustments.
For your safety, use the slope gauge included as part of
this manual to measure slopes before operating this
unit on a sloped or hilly area. If the slope is greater than
15 degrees as shown on the slope gauge, do not
operate this unit on that area or serious injury could
result.
DO:
21. Never leave a running machine unattended.
Always turn off blade(s), place transmission in
neutral, set parking brake, stop engine and remove
key before dismounting.
22. Use extra care when loading or unloading the
machine into a trailer or truck. This unit should not
be driven up or down ramp(s), because the unit
could tip over, causing serious personal injury. The
unit must be pushed manually on ramp(s) to load or
unload properly.
1. Mow up and down slopes, not across. Exercise
extreme caution when changing direction on
slopes.
2. Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
3. Use slow speed. Choose a low enough speed
setting so that you will not have to stop or shift while
on the slope. Tires may lose traction on slopes
even though the brakes are functioning properly.
Always keep machine in gear when going down
slopes to take advantage of engine braking action.
4. Follow the manufacturer’s recommendations for
wheel weights or counterweights to improve
stability.
23. Muffler and engine become hot and can cause a
burn. Do not touch.
24. Check overhead clearances carefully before driving
under low hanging tree branches, wires, door
openings etc., where the operator may be struck or
pulled from the unit, which could result in serious
injury.
25. Disengage all attachment clutches, depress the
brake pedal completely and shift into neutral before
attempting to start engine.
26. Your machine is designed to cut normal residential
grass of a height no more than 10”. Do not attempt
to mow through unusually tall, dry grass (e.g.,
pasture) or piles of dry leaves. Dry grass or leaves
may contact the engine exhaust and/or build up on
the mower deck presenting a potential fire hazard.
27. Use only accessories and attachments approved
for this machine by the machine manufacturer.
Read, understand and follow all instructions
provided with the approved accessory or
attachment.
28. Data indicates that operators, age 60 years and
above, are involved in a large percentage of riding
mower-related injuries. These operators should
evaluate their ability to operate the riding mower
safely enough to protect themselves and others
from serious injury.
5. Use extra care with grass catchers or other
attachments. These can change the stability of the
machine.
6. Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
Rapid transmission engagement or braking could
cause the front of the machine to lift and rapidly flip
over backwards which could cause serious injury.
7. Avoid starting or stopping on a slope. If tires lose
traction, disengage the blade(s) and proceed
slowly straight down the slope.
DO NOT:
1. Do not turn on slopes unless necessary; then, turn
slowly and gradually downhill, if possible.
2. Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel is over the edge of a cliff, ditch, or if
an edge caves in.
3. Do not try to stabilize the machine by putting your
foot on the ground.
4. Do not use a grass catcher on steep slopes.
5. Do not mow on wet grass. Reduced traction could
cause sliding.
6. Do not shift to neutral and coast downhill. Doing so
may cause the operator to lose control of the
machine resulting in serious injury or death.
7. Do not tow heavy pull behind attachments (e.g.
loaded dump cart, lawn roller, etc.) on slopes
greater than 5 degrees. When going down hill, the
extra weight tends to push the tractor and may
cause you to loose control. (e.g. tractor may speed
up, braking and steering ability are reduced,
attachment may jack-knife and cause tractor to
overturn).
29. If situations occur which are not covered in this
manual, use care and good judgment. Contact a
Toro Service Dealer for assistance.
SLOPE OPERATION
Slopes are a major factor related to loss of control and
tip-over accidents which can result in severe injury or
death. All slopes require extra caution. If you cannot
back up the slope or if you feel uneasy on it, do not mow
it.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Travel slowly and allow extra distance to stop.
6. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
CHILDREN
1. Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
They do not understand the dangers. Never
assume that children will remain where you last
saw them.
7. Do not shift to neutral and coast downhill.
SERVICE
SAFE HANDLING OF GASOLINE:
1. To avoid personal injury or property damage
use extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
a. Keep children out of the mowing area and in
watchful care of a responsible adult other
than the operator.
b. Be alert and turn machine off if a child enters
the area.
c. Before and while backing, look behind and
down for small children.
d. Never carry children, even with the blade(s)
shut off. They may fall off and be seriously
injured or interfere with safe machine
operation.
c. When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
d. Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times
until fueling is complete. Do not use a nozzle
lock-open device.
e. Use extreme care when approaching blind
corners, doorways, shrubs, trees or other
objects that may block your vision of a child
who may run into the machine.
f. To avoid back-over accidents, always
disengage the cutting blade(s) before
shifting into reverse. The “Reverse
Caution Mode” should not be used when
children or others are around.
g. Keep children away from hot or running
engines. They can suffer burns from a hot
muffler.
h. Remove key when machine is unattended to
prevent unauthorized operation.
e. Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
f. Never fuel machine indoors.
g. Never remove gas cap or add fuel while the
engine is hot or running. Allow engine to cool
at least two minutes before refueling.
h. Never over fill fuel tank. Fill tank to no more
than1/2-inch below the bottom of the filler
neck to allow space for fuel expansion.
i. Replace gasoline cap and tighten securely.
j. If gasoline is spilled, wipe it off the engine
and equipment. Move unit to another area.
Wait 5 minutes before starting the engine.
k. To reduce fire hazards, keep machine free of
grass, leaves, or other debris build-up. Clean
up oil or fuel spillage and remove any fuel
soaked debris.
l. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas
appliances.
m. Allow a machine to cool at least 5 minutes
before storing.
2. Never allow children under 14 years old to operate
the machine. Children 14 years old and over should
read and understand the operation instructions and
safety rules in this manual and should be trained
and supervised by a parent.
TOWING
1. Tow only with a machine that has a hitch designed
for towing. Do not attach towed equipment except
at the hitch point.
2. Follow the manufacturers recommendation for
weight limits for towed equipment and towing on
slopes.
3. Never allow children or others in or on towed
equipment.
4. Do not tow heavy pull behind attachments (e.g.
loaded dump cart, lawn roller, etc.) on slopes
greater than 5 degrees. When going down hill, the
extra weight tends to push the tractor and may
cause you to loose control. (e.g. tractor may speed
up, braking and steering ability are reduced,
attachment may jack-knife and cause tractor to
overturn).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SERVICE:
equipment is in safe working condition.
8. Never tamper with the safety interlock system or
other safety devices. Check their proper operation
before each use.
9. After striking a foreign object, stop the engine and
remove the ignition key to prevent unintended
starting. Thoroughly inspect the machine for any
damage. Repair the damage before starting and
operating.
10. Never attempt to make adjustments or repairs to
the machine while the engine is running.
11. Grass catcher components and the discharge
cover are subject to wear and damage which could
expose moving parts or allow objects to be thrown.
12. For safety protection, frequently check components
and replace immediately with original equipment
manufacturer’s (O.E.M.) parts only. Use of parts
which do not meet the original equipment
specifications may lead to improper performance
and compromise safety!
13. Do not change the engine governor settings or
over-speed the engine. The governor controls the
maximum safe operating speed of the engine.
14. Maintain or replace safety and instruction labels as
necessary (i.e. when scratched, damaged or
missing).
1. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless, and deadly gas.
2. Before cleaning, repairing, or inspecting, make
certain the blade(s) and all moving parts have
stopped. Remove the ignition key to prevent
unintended starting.
3. Periodically check to make sure the blades come to
complete stop within approximately five (5)
seconds after operating the blade disengagement
control. If the blades do not stop within the this time
frame, your unit should be serviced professionally
by a Toro Service Dealer.
4. Check brake operation frequently as it is subjected
to wear during normal operation. Adjust and service
as required.
5. Check the blade(s) and engine mounting bolts at
frequent intervals for proper tightness. Also,
visually inspect blade(s) for damage (e.g.,
excessive wear, bent, cracked).
Replace the blade(s) with the original equipment
manufacturer’s (O.E.M.) blade(s) only. Use of parts
which do not meet the original equipment
specifications may lead to improper performance
and compromise safety!
15. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
6. Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
7. Keep all nuts, bolts, and screws tight to be sure the
WARNING: YOUR RESPONSIBILITY Restrict the use of this power machine to persons who agree to
read, understand and follow the warnings and instructions in this manual and on the machine.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: SAFETY LABELS
Safety labels found on your lawn tractor are illustrated below (3/4 actual size). Always follow their instructions and heed
their warnings. If you discover a safety label is scratched, damaged or missing, order a replacement immediately.
TO REDUCE THE RISK OF INJURY, DO NOT
OPERATE UNLESS DISCHARGE COVER OR
GRASS CATCHER IS IN ITS PROPER PLACE.
IF DAMAGED, REPLACE IMMEDIATELY.
DANGER
KEEP HANDS AND FEET AWAY.
DO NOT OPERATE MOWER
UNLESS CHUTE DEFLECTOR
OR ENTIRE GRASS CATCHER IS
S30503
IN ITS PROPER PLACE.
ASSEMBLE CHUTE DEFLECTOR TO THIS UNIT BEFORE OPERATING.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: INSTRUCTIONAL LABELS
Instructional labels found on your lawn tractor are illustrated below (3/4 actual size). Always follow their instructions and
heed their warnings. If you discover a label is scratched, damaged or missing, order a replacement immediately.
LX420
LX460
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: TRACTOR SET-UP
Gas and Oil Fill-up
Attaching the Battery Cables
Tools Required
Use only clean, fresh (under 30 days old), unleaded
gasoline. Fill tank to no more than 1/2 inch below the
top of the filler neck to allow space for fuel expansion.
(1) 7/16" wrench
WARNING: California Proposition 65
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other sources of
ignition before filling the fuel tank.
Warning: Battery posts, terminals, and
related accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive
harm. Wash hands after handling.
NOTE: Your tractor’s battery cables may have
already be attached at the factory.
Service the engine with gasoline and oil as instructed in
the separate engine manufacturer’s Operator/Owner
Manual packed with your tractor. Read instructions
carefully.
NOTE: The positive battery terminal is marked Pos.
(+). The negative battery terminal is marked Neg. (–).
•
The positive cable (heavy red wire) is secured to
the positive battery terminal (+) with a hex bolt and
hex nut at the factory. Make certain that the rubber
boot covers the terminal to help protect it from
corrosion.
Remove the hex bolt and hex nut from the negative
cable.
Remove the black plastic cover, if present, from the
negative battery terminal and attach the negative
cable (heavy black wire) to the negative battery
terminal (–) with the bolt and hex nut.
Attaching The Steering Wheel
Tools Required
(1) 1/2" socket wrench
•
•
1. The hardware for attaching the steering wheel has
been packed within the steering wheel, beneath
steering wheel cap. Carefully pry off the steering
wheel cap and remove the hardware.
2. With the wheels of the tractor pointing straight
forward, place the steering wheel over the steering
shaft.
3. Place the washer (with the cupped side down) over
the steering shaft and secure with the hex bolt. See
•
Make certain the hold-down rod is in position over
Cap
Rubber
Boot
Hex Bolt
Washer
Hold Down Rod
Steering Shaft
Hex Nut
Hex Bolt
Figure 2
NOTE: If the battery is put into service after the date
shown on top/side of battery, charge the battery as
the tractor.
Figure 1
4. Place the steering wheel cap over the center of the
steering wheel and push downward until it “clicks”
into place.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tire Pressure
Shipping Brace Removal
WARNING: Maximum tire pressure under
WARNING: Make sure the riding mower’s
engine is off, set the parking brake and
remove the ignition key before removing the
shipping brace.
any circumstances is 30 psi. Equal tire
pressure should be maintained at all times.
The tires on your unit may be over-inflated for shipping
purposes. Reduce the tire pressure before operating
the tractor. Recommended operating tire pressure is
approximately 10 p.s.i for the rear tires & 14 p.s.i. for the
front tires. Check sidewall of tire for maximum p.s.i.
•
•
Locate the shipping brace, if present, and warning
tag found on the right side of the cutting deck. See
While holding the discharge chute with your left
hand, remove the shipping brace with your right
hand by grasping it between your thumb and index
finger and rotating it clockwise.
Attaching The Seat
1. Remove the two knobs from the bottom of seat.
2. Position the shoulder screws (found on the base of
the seat) inside the slot openings in the seat pivot
bracket.
3. Slide the seat slightly rearward in the seat pivot
bracket, lining up the rear slots in the pivot bracket
with the remaining two holes in the seat’s base.
4. Select desired position for the seat, and secure with
Knobs
Figure 4
WARNING: The shipping brace, used for
packaging purposes only, must be removed
and discarded before operating your riding
mower.
WARNING: The mowing deck is capable of
throwing objects. Failure to operate the riding
mower without the discharge cover in the
proper operating position could result in
serious personal injury and/or property
damage.
Shoulder Screws
Figure 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Gauge Wheels
Tools Required
Lock Nut
(2) 9/16" wrenches
Gauge Wheel
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right fender.
Adjust the deck wheels so that they are between ¼-inch
and ½-inch above the ground as follows.
WARNING: Keep hands and feet away
from the discharge opening of the cutting
deck.
Place the tractor on a firm and level surface, preferably
Shoulder Screw
•
Place the tractor’s deck lift handle in the normally
desired mowing height setting, then check the
gauge wheels for contact or excessive clearance
with the surface below. There should be
approximately 1/2" clearance.
If the wheels contact the surface adjust as follows:
a. Raise the deck lift handle to its highest
setting.
Figure 5
e. Note the position of the index hole used; then
install the other rear gauge wheel into the
corresponding index hole of the other gauge
wheel brackets.
•
•
If the gauge wheels have excessive clearance with
the surface below, lower the wheels to the index
hole that provides the approximate 1/2" clearance
as described above.
b. Remove the rear gauge wheels by removing
the lock nuts and shoulder screws which
secure them to the deck.
c. Place the deck lift handle in the desired
mowing height setting.
d. Insert the shoulder screw with the rear gauge
wheel into the index hole that leaves
approximately 1/2" between the bottom of the
more detailed instructions regarding various deck
adjustments.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: KNOW YOUR LAWN TRACTOR
A
G
H
B
C
W
O
SL
I
J
D
E
K
F
NOTE: Steering Wheel not shown for clarity.
Figure 6
A Systems Indicator Monitor/Hour Meter G Throttle / Choke Control
B PTO (Blade Engage) Lever
C Parking Brake Lever
D Cruise Control Lever
E Shift Lever
H Ignition Switch Module
I Brake Pedal
J Drive Pedal
K Deck Lift Lever
F Cup Holder
NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator’s position.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Throttle / Choke Control
Ignition Switch Module
Choke
Position
The throttle/choke control is
located on the right side of the
tractor’s dash panel. This lever
controls the speed of the engine
and, when pushed all the way
forward, the choke control also.
When set in a given position, the
throttle will maintain a uniform
engine speed.
WARNING: Never leave a running machine
unattended. Always disengage PTO, move
shift lever into neutral position, set parking
brake, stop engine and remove key to prevent
unintended starting.
FAST
To start the engine, insert the key into the ignition
switch and turn clockwise to the START position.
Release the key into the NORMAL MOWING MODE
position once the engine has fired.
IMPORTANT: When operating the
tractor with the cutting deck
engaged, be certain that the
throttle/choke control is always
in the FAST (rabbit) position.
To stop the engine, turn the ignition key
SLOW
Normal
Mowing Mode
Brake Pedal
The brake pedal is located on the
right front side of the tractor
above the drive pedal along the
running board. The brake pedal
can be used for sudden stops or
setting the parking brake.
Stop
Position
Start
Position
NOTE: The brake pedal must
be fully depressed to activate the
safety interlock switch when
starting the tractor.
Figure 7
Shift Lever
IMPORTANT: Prior to operating the tractor, refer to both
regarding the Ignition Switch Module and operating the
tractor in REVERSE CAUTION MODE.
The shift lever is located on the
left side of the fender and has
three positions, FORWARD,
NEUTRAL and REVERSE. The
brake pedal must be depressed
and the tractor must not be in
motion when the moving shift
lever.
F
Drive Pedal
N
R
The drive pedal is located below
the brake pedal on the right front
side of the tractor along the
running board. Depress the drive
pedal with your right foot when
the tractor shift lever is in either
FORWARD or REVERSE to
IMPORTANT: Never force the shift
lever. Doing so may result in
serious damage to the tractor’s
transmission.
Deck Lift Lever
cause the tractor to move.
Found on your tractor’s right
fender, the deck lift lever is used
to change the height of the
cutting deck. To use, move the
lever to the left, then place in the
notch best suited for your
application.
Ground speed is also controlled
with the drive pedal. The further
down the pedal is depressed, the faster the tractor will
travel. The pedal will return to its original position when
released.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Systems Indicator Monitor / Hour Meter
PTO (Blade Engage) Lever
Battery
ON
Oil
OFF
PTO
PTO / BLADE ENGAGE
LCD
42.0
The PTO (Blade Engage) lever is located on the left
side of the dash, next to the steering wheel. Move the
PTO (Blade Engage) lever forward to engage the
power to the cutting deck or other (separately available)
attachments; move the PTO (Blade Engage) lever
rearward to disengage the power to the attachments.
PTO
Parking Brake
(Blade Engage)
NOTE: The PTO (Blade Engage) lever must be in the
disengaged (OFF) position when starting the engine.
LCD
Located in the center of the tractor’s console, the
systems indicator monitor records, and displays on its
LCD, hours of tractor operation whenever the ignition
key is rotated out of the STOP position.
Cruise Control
Lever
The cruise control
The Indicator Monitor will also remind the operator of
maintenance intervals for changing the engine oil. The
LCD will alternately flash the recorded hours, “CHG”
and “OIL” for five minutes, after every 50 hours of
recorded operation elapse. The maintenance interval
lasts for two hours (from 50-52, 100-102, 150-152,
etc.). The LCD will also flash as described above for
five minutes every time the tractor’s engine has been
started during this maintenance interval. Before the
interval expires, change the crankcase oil level as
instructed in the MAINTENANCE section of this manual.
lever is located on
the tractor dash
panel, below the steering wheel. Push the cruise
control lever downward while traveling forward at a
desired speed. While holding the lever down, release
pressure from the drive pedal.
This will engage the cruise control and allow the tractor
to remain at that speed without applying pressure to the
drive pedal. Depress the brake pedal or the drive pedal
detailed instructions regarding cruise control.
Brake
If the Brake light illuminates when attempting to start
the tractor’s engine, depress the brake pedal.
NOTE: Cruise control can NOT be engaged at the
tractor’s fastest ground speed. If the operator should
attempt to do so, the tractor will automatically
decelerate to the fastest optimal mowing ground speed.
PTO (Blade Engage)
If the PTO light illuminates when attempting to start the
tractor’s engine, move the PTO lever into the
disengaged (OFF) position.
Parking Brake
Lever
Oil
It is normal for the Oil light to illuminate while the engine
is cranking during start-up, but if it illuminate’s during
operation, while the engine is running, stop the
tractor immediately and check the crankcase oil level
as instructed in the MAINTENANCE section of this manual.
To set the parking
brake, fully depress
the brake pedal and
push the parking brake lever down. Hold the lever down
while taking your foot off the brake pedal. Both the
parking lever and the brake pedal will then stay
depressed. To release the parking brake, depress the
brake pedal slightly. The parking brake lever will then
return to its original position.
Battery
It is normal for the Battery light to illuminate while the
engine is cranking during start-up, but if it illuminate’s
during operation, while the engine is running, the
battery is in need of a charge or the engine’s charging
system is not generating sufficient amperage. Refer to
the MAINTENANCE section of this manual for the proper
battery charging procedure or have the charging
system checked by an authorized Toro Service Dealer.
IMPORTANT: Always set the parking brake when
leaving the tractor unattended.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: OPERATING YOUR LAWN TRACTOR
WARNING: Use extreme caution while
Safety Interlock System
operating the tractor in the REVERSE
CAUTION MODE. Always look down and
behind before and while backing. Do not
operate the tractor when children or others
are around. Stop the tractor immediately if
someone enters the area.
This tractor is equipped with a safety interlock system
for the protection of the operator. Before each use,
check the safety interlock system for proper operation.
If the interlock system should ever malfunction, do not
operate the tractor. Contact a Toro service dealer.
•
The safety interlock system prevents the engine
from cranking or starting unless the parking brake is
engaged, and the PTO (Blade Engage) lever is in
the disengaged (OFF) position. To check for proper
operation, move the PTO (Blade Engage) lever into
the engaged (ON) position and release the parking
brake. Attempts to start the tractor’s engine should
fail.
To use the REVERSE CAUTION MODE:
IMPORTANT:The operator MUST be seated in the
tractor seat.
1. Start the engine as previously instructed in this
Operator’s Manual.
2. Turn the key from the NORMAL MOWING
(Green) position to the REVERSE CAUTION
MODE (Yellow) position of the key switch module.
3. Depress the REVERSE PUSH BUTTON (Orange,
Triangular Button) at the top, right corner of the key
switch module. The red indicator light at the top, left
corner of the key switch module will be ON while
4. Once activated (indicator light ON), the tractor can
be driven in reverse with the cutting blades (PTO)
engaged.
•
•
The engine will automatically shut off if the operator
leaves the seat before engaging the parking brake.
To check for proper operation, start the tractor’s
engine, release the parking brake and momentarily
raise yourself from the seat. The engine should
stall.
The engine will automatically shut off if the operator
leaves the tractor’s seat with the PTO (Blade
Engage) lever in the engaged (ON) position,
regardless of whether the parking brake is
engaged. To check for proper operation, start the
tractor’s engine, move the PTO (Blade Engage)
lever in the engaged (ON) position and momentarily
raise yourself from the seat. The engine should
stall.
5. Always look down and behind before and while
backing to make sure no children are around.
6. After resuming forward motion, return the key to the
NORMAL MOWING position.
•
With the ignition key in the NORMAL MOWING
position, the engine will automatically shut off if the
PTO (Blade Engage) lever is moved into the
engaged (ON) position with the shift lever in
Reverse. To check for proper operation, start the
tractor’s engine with the ignition key in the
NORMAL MOWING position, move the PTO
(Blade Engage) lever in the engaged (ON) position,
and place the shift lever into REVERSE. The
engine should stall.
IMPORTANT: The REVERSE CAUTION MODE will
remain activated until:
a. The key is placed in either the NORMAL
MOWING position or STOP position.
b. The operator leaves the seat.
Reverse
Push Button
Indicator
Light
Reverse
WARNING: Do not operate the tractor if the
interlock system is malfunctioning. This
system was designed for your safety and
protection.
Caution Mode
Stop
Position
Position
Start
Position
Reverse Caution Mode
The REVERSE CAUTION MODE position of the key
switch module allows the tractor to be operated in
reverse with the blades (PTO) engaged.
IMPORTANT: Mowing in reverse is not recommended.
Figure 8
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the Engine
Driving The Tractor
WARNING: Do not operate the tractor if the
interlock system is malfunctioning. This
system was designed for your safety and
protection.
WARNING: Avoid sudden starts, ex-
cessive speed and sudden stops.
WARNING: Do not leave the seat of the
tractor without first placing the PTO (Blade
Engage) lever in the disengaged (OFF)
position, depressing the brake pedal and
engaging the parking brake. If leaving the
tractor unattended, also turn the ignition key
off and remove the key.
manual for Gasoline and Oil fill-up instructions.
•
•
Insert the tractor key into the ignition switch
module.
Place the PTO (Blade Engage) lever in the
disengaged (OFF) position.
Engage the tractor’s parking brake.
Activate the choke control.
Turn the ignition key clockwise to the START
position. After the engine starts, release the key. It
will return to the NORMAL MOWING position.
•
•
Depress the brake pedal to release the parking
brake and let the pedal up.
Move the throttle/choke control into the FAST
(rabbit) position.
•
•
•
IMPORTANT: Do NOT use the shift lever to change the
direction of travel when the tractor is in motion. Always
use the brake pedal to bring the tractor to a complete
stop before shifting.
IMPORTANT: Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing so
may cause damage to your engine’s electric starter.
•
To move forward, place the shift lever in the
FORWARD position, then slowly depress the drive
pedal until the desired speed is achieved.
To move in reverse, place the shift lever in the
REVERSE position, check that the area behind is
clear then slowly depress the drive pedal.
•
After the engine starts, deactivate the choke
control.
•
NOTE: Do NOT leave the choke control on while
operating the tractor. Doing so will result in a "rich" fuel
mixture and cause the engine to run poorly.
Driving On Slopes
Stopping the Engine
WARNING: If you strike a foreign object,
stop the engine and remove the ignition key.
Thoroughly inspect the machine for any
damage. Repair the damage before restarting
and operating
slopes where you may operate the tractor safely.
WARNING: Do not mow on inclines with a
slope in excess of 15 degrees (a rise of
approximately 2-1/2 feet every 10 feet). The
tractor could overturn and cause serious
injury.
•
•
•
•
If the blades are engaged, place the PTO/Blade
Engage lever in the disengaged (OFF) position.
Position the throttle/choke control between half-
throttle and the FAST (rabbit) position
Turn the ignition key counterclockwise to the STOP
position.
•
•
Mow up and down slopes, NEVER across.
Exercise extreme caution when changing direction
on slopes.
•
•
•
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
Avoid turns when driving on a slope. If a turn must
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
Avoid stopping when driving up a slope. If it is
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
Remove the key from the ignition switch to prevent
unintended starting.
Using the Deck Lift Lever
To raise the cutting deck, move the deck lift lever to the
left, then place it in the notch best suited for your
application. Refer to Setting The Cutting Height earlier in
this section.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Keep the throttle/choke control in the FAST (rabbit)
position for the most efficient use of the cutting
deck or other (separately available) attachments
Setting The Cruise Control
NOTE: The cruise control feature should only be
utilized while traveling in the forward direction.
IMPORTANT: The engine will automatically shut off if the
PTO is engaged with the shift lever in position for
reverse travel and the ignition key in the NORMAL
MOWING position. Refer to Safety Interlock System on
•
Slowly depress the drive pedal until the desired
speed is achieved.
•
•
Lightly depress the cruise control lever.
While continuing to hold the cruise lever down, lift
your foot from the drive pedal (you should feel the
cruise latch engage).
Mowing
•
Once engaged, the cruise control lever and the
drive pedal will lock in the “down” position, and the
tractor will maintain the same forward speed.
WARNING: To help avoid blade contact or
a thrown object injury, keep bystanders,
helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop
machine if anyone enters the area.
NOTE: Cruise control can not be set at the tractor’s
fastest ground speed. If the operator should attempt to
do so, the tractor will automatically decelerate to the
fastest optimal mowing ground speed.
This tractor is equipped with one of Toro’s quality
cutting decks. The following information will be helpful
when using the cutting deck with your tractor.
Disengage the cruise control using one of the following
methods:
WARNING: Plan your mowing pattern to
avoid discharge of materials toward roads,
sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or
obstruction which may cause discharged
material to ricochet back toward the operator.
•
Depress the brake pedal to disengage the cruise
control and stop the tractor.
Lightly depress the drive pedal.
•
To change to the reverse direction when operating with
cruise control, depress the brake pedal to disengage
the cruise control and bring the tractor to a complete
stop. Place the shift lever in the REVERSE position and
depress the drive pedal.
•
•
Do not mow at high ground speed, especially if a
mulch kit or grass collector is installed.
For best results it is recommended that the first two
laps be cut with the discharge thrown towards the
center. After the first two laps, reverse the direction
to throw the discharge to the outside for the
balance of cutting. This will give a better
appearance to the lawn.
Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
Mowing should always be done with the engine at
full throttle.
Under heavier conditions it may be necessary to go
back over the cut area a second time to get a clean
cut.
Do NOT attempt to mow heavy brush and weeds
and extremely tall grass. Your tractor is designed to
mow lawns, NOT clear brush.
Engaging the Parking Brake
To engage the parking brake:
•
•
•
Fully depress the brake pedal and hold it while
gently pushing the parking brake lever downward.
Hold the parking brake lever down while removing
your foot from the brake pedal.
Once engaged, the parking brake lever and the
brake pedal will lock in the “down” position.
•
•
•
To disengage the parking brake:
•
Slightly depress the brake pedal.
NOTE: The parking brake must be engaged if the
operator leaves the seat with the engine running or the
engine will automatically shut off.
•
•
Keep the blades sharp and replace the blades
manual for proper blade sharpening instructions.
Engaging the Blades
Engaging the PTO (Blade Engage) transfers power to
the cutting deck or other (separately available)
attachments. To engage the blades, proceed as
follows:
•
Move the throttle/choke control to the FAST (rabbit)
position.
•
Grasp the PTO (Blade Engage) lever and pivot it all
the way forward into the engaged (ON) position.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: MAKING ADJUSTMENTS
•
•
•
Determine the approximate distance necessary for
proper adjustment and proceed, if necessary, to the
next step.
From the front of the tractor, loosen the outermost
hex lock nut on the end of the deck hanger rod. See
Tighten the inner hex nut front against the front
hanger bracket to raise the front of the deck; loosen
the hex nut to lower the front of the deck. See
WARNING: Never attempt to make any
adjustments while the engine is running,
Seat Adjustment
To adjust the position of the seat, loosen the two knobs
forward or rearward as desired. Retighten the two
knobs.
LX 420
Knobs
Figure 10
Figure 9
LX 460
Leveling the Deck
NOTE: Check the tractor’s tire pressure before
performing any deck leveling adjustments. Refer to
Front To Rear
The front of the cutting deck is supported by a stabilizer
bar that can adjusted to level the deck from front to rear.
The front of the deck should be between 1/4-inch and
3/8-inch lower than the rear of the deck. Adjust if
necessary as follows:
•
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate the blade nearest the discharge
chute so that it is parallel with the tractor.
Measure the distance from the front of the blade tip
to the ground and the rear of the blade tip to the
ground.
•
•
Figure 11
•
Retighten the two lock nuts against the inner hex
nuts when proper adjustment is achieved.
The first measurement taken should be between
1/4" and 3/8" less than the second measurement.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Side to Side
Parking Brake Adjustment
If the cutting deck appears to be mowing unevenly, a
side to side adjustment can be performed. Adjust if
necessary as follows:
WARNING: Never attempt to adjust the
brakes while the engine is running. Always
disengage PTO, move shift lever into neutral
position, stop engine and remove key to
prevent unintended starting.
•
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate both blades so that they are
perpendicular with the tractor.
If the tractor does not come to a complete stop when
the brake pedal is completely depressed, or if the
tractor’s rear wheels can roll with the parking brake
applied, the brake is in need of adjustment. The brake
disc can be found on the right side of the transmission
in the rear of the tractor. Adjust if necessary as follows:
•
Measure the distance from the outside of the left
blade tip to the ground and the distance from the
outside of the right blade tip to the ground. Both
measurements taken should be equal. If they’re
not, proceed to the next step.
•
Loosen, but do NOT remove, the hex bolt on the left
•
Looking at the transmission from the right side of
the tractor, locate the compression spring and
Brake Puck
Hex Nut
Adjustment Gear
Hex Bolt
Brake Disc
Figure 12
Spring
•
•
•
Balance the deck by using a wrench to turn the
The deck is properly balanced when both blade tip
measurements taken earlier are equal.
Retighten the hex bolt on the left deck hanger
bracket when proper adjustment is achieved.
Figure 13
•
•
Loosen, but do NOT remove, the hex nut found on
Insert a feeler gauge (set at .011”) between the
brake disk and the brake puck.
NOTE: If a feeler gauge is unavailable, a typical
business card is approximately .011” thick.
•
Retighten the hex nut loosened earlier, leaving a
.011” gap between the brake disc and the brake
puck.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Remove the hex nut on the top of ball joint. See
Thread the ball joint toward the jam nut to shorten
the drag link. Thread the ball joint away from the
jam nut to lengthen the drag link.
Steering Adjustment
If the tractor turns tighter in one direction than the other,
or if the ball joints are being replaced due to damage or
wear, the steering drag links may need to be adjusted.
Adjust the drag links so that equal lengths are threaded
into the ball joint on the left side and the ball joint on the
right side:
•
Replace hex nut and lock washer and retighten the
jam nut after proper adjustment is achieved.
NOTE: Threading the ball joints too far onto the drag
links will cause the front tires to "toe-in" too far. Proper
toe-in is between 1/16" and 5/16".
•
Loosen the jam nut found on the drag link at the
rear of the ball joint. See Figure 14.
Front tire toe-in can be measured as follows:
•
Place the steering wheel in position for straight
ahead travel.
•
In front of the axle, measure the distance
horizontally from the inside of the left rim to the
inside of the right rim. Note the distance.
Behind the axle, measure the distance horizontally
from the inside of the left rim to the inside of the
right rim. Note the distance.
The measurement taken in front of the axle should
be between 1/16" and 5/16" less than the
measurement taken behind the axle.
Adjust if necessary.
Hex Nut
•
•
•
Drag Link
Ball
Joint
Jam
Nut
Figure 14
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: MAINTAINING YOUR LAWN TRACTOR
reference of recommended maintenance intervals.
TEMPERATURE / OIL VISCOSITY CHART
WARNING:
maintenance or repairs, disengage PTO, set
parking brake, stop engine and remove key to
prevent unintended starting.
Before performing any
**
5W-20, 5W-30
*
10W-30
Engine
-20
-30
0
20
32 40
0
60
80
100
40
°F
°C
-20
-10
10
20
30
Maintenance, repair, or replacement of the emission
control devices and systems, which are being done at
the customer’s expense, may be performed by any
engine repair establishment or individual. Warranty
repairs must be performed by a Toro Dealer.
Temperature Change Expected Before Next Oil Change
*Use of synthetic oil having 5W-20 or 5W-30 rating is acceptable,
up to 4°C (40°F).
**Synthetic oils will provide better starting in extreme cold below
23°C (-10°F).
Engine Oil
The engine-crankcase is filled with 10W-30 ship-away
oil at the factory. This oil may be used for the first 24
hours of engine operation at temperatures between
0°F and 80°F. If temperatures are not within this range,
drain the oil from the oil filter and crankcase and
replace with new oil.
IMPORTANT: Never operate
the engine with the oil level
below the ADD mark or
above the FULL mark on the
FULL
dipstick.
The engine oil must be drained and replaced with new
oil after 24 hours of engine operation and every 50
hours thereafter. Refer to the Oil Viscosity Chart below
to determine the proper oil type.
•
After checking the oil lev-
el (and adding oil, if nec-
essary), reinstall the oil
fill cap/dipstick by insert-
ing it into the oil fill tube.
Operating Range
NOTE: To aid starting, the selection of crankcase oil
should be based on the lowest anticipated
temperatures prior to the next scheduled oil change.
Adding Oil
ADD
If, after checking the oil level,
you find the dipstick reads
ADD, proceed as follows.
Checking the Oil Level
It is important to check the oil level at least every four
hours of operation. Regular checking during the first 24
hours of operation is especially important. Check the oil
level before each use as follows:
•
Place the tractor on a level surface and engage the
parking brake. Stop the tractor engine and remove
the ignition key.
•
Allow the engine a few minutes to rest after opera-
tion. This will give the oil time to drain into the crank-
case sump and result in a more accurate dipstick
reading.
Clean the area around the oil fill cap/dipstick to pre-
vent debris from entering the crankcase.
•
•
Clean the area around the oil fill cap and fill tube to
prevent debris from entering the crankcase.
Remove the oil fill cap/dipstick from the oil fill tube
and SLOWLY pour oil into the oil fill tube. Do NOT
pour more than 6 oz. of oil at a time without first
stopping and re-checking the oil level.
Fill the crankcase until the oil level reaches the full
(F) mark on the dipstick. See Figure above. Refer to
the oil viscosity chart earlier in this section for
information regarding the proper type of oil to add
to the crankcase.
•
•
•
•
Remove the oil fill cap/dipstick by lifting it out of the
oil fill tube.
Wipe the dipstick clean before pushing it all the way
back into the oil fill tube. Withdraw the dipstick to
check the oil level. Refer to figure at right.
IMPORTANT: The engine (with oil filter) has a capacity of
1.5 liters (50.75 oz.). Never overfill the engine
crankcase.
•
Always keep the oil level at or near the FULL mark
on the dipstick. If the oil is low, add oil of the proper
type up to the FULL mark. Always re-check the oil
level with the dipstick before adding more oil.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: The engine may overheat and/or damage
may result if the oil level is below the ADD or over the
FULL on the dipstick.
Oil Fill Cap /
Dipstick
•
Reinstall the oil fill cap/dipstick securely onto the oil
fill tube.
IMPORTANT: The oil fill cap/dipstick must be installed
securely onto the tube at all times when the engine
is operating. Severe engine damage could result from
failure to do so.
Changing the Engine Oil
The engine oil and oil filter should be changed after the
first 24 hours of operation, and after every 50 hours of
operation thereafter.
Oil Filter
Drain Port
Oil Drain Hose
WARNING: If the engine has been recently
run, the engine, muffler and surrounding
metal surfaces will be hot and can cause
burns to the skin. Allow the tractor to cool and
use caution when removing
Figure 15
Changing the Oil Filter
After draining the oil, proceed as follows:
•
•
•
Before removing the old oil filter, clean around its
base to prevent debris from entering the crankcase.
Grasp the oil filter and remove it from the filter
adapter by turning it counterclockwise.
Place a new replacement filter in a shallow pan with
the open end up and pour new oil of the proper type
center hole.
IMPORTANT: The oil filter should be changed at every
oil change interval.
To complete an oil change, proceed as follows:
Draining the Oil
Run the engine for a few minutes to allow the oil in the
crankcase to warm up. Warm oil will flow more freely
and carry away more of the engine sediment which may
have settled at the bottom of the crankcase. Use care to
avoid burns from hot oil.
IMPORTANT: Stop pouring when the oil reaches the
bottom of the threads and allow a minute or two for the
oil to be absorbed by the filter material.
•
Pop open the protective cap on the end of the oil
drain valve to expose the drain port. See Figure 15
Remove the oil fill cap/ dipstick from the oil fill tube.
Push the oil drain hose (packed with this manual)
onto the oil drain port. Route the opposite end of
the hose into an appropriate oil collection container
with a capacity great enough to collect the used oil
(approximately 2.5 liters).
•
Put a drop of oil on your fingertip and apply a light
coating to the gasket of the new oil filter.
Install the replacement oil filter on the engine by
turning it clockwise onto the filter adapter until the
rubber gasket makes contact with the base. Tighten
the filter an additional 1/2 turn after the gasket first
makes contact.
•
•
•
•
•
Push the oil drain valve in slightly, then rotate
counterclockwise and pull outward to begin
draining oil.
After the oil has finished draining, push the oil drain
valve back in, rotate it clockwise to lock the valve
closed and re-cap the end of the oil drain valve to
keep debris from entering the drain port.
Re-filling the Crankcase with Oil
IMPORTANT: The engine (with oil filter) has a capacity of
1.5 liters (50.75 oz.). Do NOT overfill. Always check the
adding more oil.
NOTE: For the proper oil type, refer to the chart on
IMPORTANT: Always change the oil filter when
performing an oil change on your tractor’s engine.
•
•
Clean the area around the oil fill tube to prevent
debris from entering the crankcase.
Slowly pour oil into the fill tube. Fill the crankcase
until the oil level reaches the full (F) mark on the
Reinstall the oil fill cap/dipstick securely into the oil
fill tube.
•
23
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: The oil fill cap/dipstick must be installed
securely onto the tube at all times when the engine
is operating. Severe engine damage could result from
a failure to do so.
Service Paper Element
The paper element should be replaced at least once a
season, or every 100 hours of operation. Replace
more frequently if the tractor is operated under
extremely dusty conditions. To replace the paper
element, proceed as follows:
•
Start the tractor engine and allow it to run for thirty
seconds, then stop the engine and remove the
ignition key.
•
Loosen the air cleaner cover knob(s) and remove
the cover.
•
•
Check the oil level and add oil if necessary. Do not
overfill the engine crankcase.
Examine the area around the base of the oil fill
tube, the oil filter adapter, and the oil drain valve for
leaks before operating the tractor.
•
Remove the air cleaner element with precleaner.
Remove the precleaner from the element and
service as instructed earlier in this section.
IMPORTANT: Do not wash the paper element or use
IMPORTANT: If leaks are present, have your engine
serviced by your Toro dealer before operating the
tractor.
pressurized air, as this will damage the element.
Examine the element and discard if dirt and/or damage
is present.
NOTE: Handle new element carefully; do not use if
Air Filter
the sealing surfaces are bent or damaged.
The engine is equipped with a replaceable, high density
paper air cleaner element and an oiled, foam
•
If any loose dirt or debris fell on the air cleaner base
when the element was removed, carefully remove it
and wipe the base clean. Be careful that none of it
drops into the intake.
precleaner. Always examine the air cleaner before
starting the engine. Check for a buildup of dirt and
debris around the air cleaner system. Keep this area
clean. Also check for loose or damaged components.
Replace all bent or damaged air cleaner components.
•
Check the air cleaner base. Make sure it is secured
and not damaged. Also check the air cleaner cover
for damage or improper fit. Replace all damaged air
cleaner components.
NOTE: Starting the tractor with loose or damaged air
cleaner components could allow unfiltered air into the
engine causing premature wear and failure.
•
•
Install the precleaner over the new paper element
and reinstall the element.
On single-cylinder models, reinstall the cover and
tighten the knobs securely.
Precleaner
Wash and re-oil the precleaner every 25 hours of
operation if equipped, (more often under extremely
dusty or dirty conditions).
Spark Plug
Once a season, o r every 100 hours of operation,
remove the spark plug(s), check condition, and reset
the gap or replace with a new plug(s) as necessary.
•
Loosen the air cleaner cover knob and remove the
cover.
•
•
Remove the precleaner.
•
•
•
Lift the tractor’s hood and locate the spark plug wire
on the front, right area of the engine.
Carefully pull the spark plug wire boot off of the
spark plug.
Before removing the spark plug, clean the area
around the base of the plug to keep dirt and debris
out of the engine.
Using a ratchet with a 5/8-inch spark plug socket,
remove the spark plug and check its condition.
Replace the plug if worn, dirty or damaged. Reuse
only after resetting the gap as instructed.
Wash the precleaner in warm water with detergent.
Rinse the precleaner thoroughly until all traces of
detergent are eliminated. Squeeze out excess
water (do not wring). Allow the precleaner to air dry.
Saturate the precleaner with new engine oil.
Squeeze out all excess oil.
Reinstall the precleaner into the upper section of
the air cleaner cover.
Reinstall the air cleaner cover and tighten the
knob(s) securely.
•
•
•
•
•
NOTE: Do not clean the spark plug using an abrasive
grit. Some grit could remain in the spark plug and enter
the engine causing extensive wear and damage.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Check the gap using a feeler gauge and adjust, if
necessary, by carefully bending the ground
.76 mm (0.030 in.).
Lubrication
WARNING: Before lubricating, repairing, or
inspecting, always disengage PTO, set
parking brake, stop engine and remove key to
prevent unintended starting.
Feeler Gauge
Spark Plug
Engine
engine-related lubrication.
Front Wheels
Each of the front wheel axles and rims is equipped with
an equivalent No. 2 multi-purpose lithium grease after
every 25 hours of tractor operation.
Ground Electrode
Gap
Axle Grease Fitting
Figure 16
•
•
Reinstall the spark plug into the cylinder head.
Torque the spark plug to 38.0/43.4 N·m (28/32 ft.
lb.).
Place the spark plug wire boot over the spark plug
and press until you feel it “click” in place.
Fuel Filter
WARNING: Do not replace the fuel filter
when engine is hot.
Rim Grease Fitting
The engine is equipped with an inline fuel filter located
on the right side of the engine.
Figure 17
Pivot Points & Linkage
Visually inspect the filter periodically for a build-up of
residue inside the filter body, and for a dirty element
which can be indicated by discoloration. Replace the
fuel filter when dirty.
Lubricate all the pivot points on the drive system,
parking brake and lift linkage at least once a season
with light oil.
Cleaning the Engine
Any fuel or oil spilled on the machine should be wiped
off promptly.
Do NOT allow debris to accumulate around the cooling
fins of the engine or on any other part of the machine,
especially the belts and pulleys.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10: SERVICE
Tires
Hex Flange Nut
Wood Block
WARNING: Never exceed the maximum
inflation pressure shown on the sidewall of the
tire.
The recommended operating tire pressure is
approximately 10 psi for the rear tires and 14 psi for the
front tires. Do not overinflate. Uneven tire pressure
could cause the cutting deck to mow unevenly.
Fuse
A 20 amp fuse is installed in your tractor’s wiring
harness to protect the tractor’s electrical system from
damage caused by excessive amperage.
If the electrical system does not function, or your
tractor’s engine will not crank, first check to be certain
that the fuse has not blown.
Spindle Assembly
Figure 18
It can be found under the hood mounted between the
dash panel and fuel tank on the right-hand support bar.
•
To properly sharpen the cutting blades, remove
equal amounts of metal from both ends of the
blades along the cutting edges, parallel to the
trailing edge, at a 25° to 30° angle.
IMPORTANT: Always use a 20 amp fuse for
replacement.
WARNING: Before servicing, repairing, or
inspecting, always disengage PTO, set
parking brake, stop engine and remove key to
prevent unintended starting.
Damaged Blade Edge
Cutting Blades
WARNING: Be sure to shut the engine off,
and remove the ignition key to prevent
unintended starting before removing the
Seperation
cutting
blade(s)
for
sharpening
or
replacement. Protect your hands by using
heavy gloves when grasping the blade.
WARNING: Periodically inspect the blade
adapter and/or spindle for cracks or damage,
especially if you strike a foreign object.
Replace immediately if damaged.
Figure 19
IMPORTANT: If the cutting edge of the blade has already
been sharpened, or if any metal separation is present,
replace the blades with new ones.
The blades may be removed as follows.
•
•
•
Remove the deck from beneath the tractor, (refer to
the deck over to expose its underside.
Place a block of wood between the center deck
housing baffle and the cutting blade to act as a
stabilizer. See Figure 18.
Use a 1-1/8" wrench to remove the hex flange nut
that secures the blade to the spindle assembly. See
It is important that each cutting blade edge be ground
equally to maintain proper blade balance. A poorly
balanced blade will cause excessive vibration and may
cause damage to the tractor and result in personal
injury.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT:When replacing the blade, be sure to
install the blade with the side of the blade marked
‘‘Bottom’’ (or with a part number stamped in it) facing
the ground when the mower is in the operating position.
•
•
Set the tractor’s parking brake before removing the
jumper cables, in reverse order of connection.
Allow the tractor’s engine to run for 15 minutes
before shutting it off to allow the alternator time to
charge the discharged battery.
•
IMPORTANT:Use a torque wrench to tighten the blade
spindle hex flange nut to between 70 lbs-ft. and 90 lbs-
ft.
Charging
If the unit has not been put into use for an extended
period of time, charge the battery with an automotive-
type 12-volt charger for a minimum of one hour at a
maximum of six amps.
Battery
California Proposition 65 Warning: Battery
posts, terminals, and related accessories
contain lead and lead compounds, chemicals
known to the State of California to cause
cancer and reproductive harm. Wash hands
after handling.
WARNING: Batteries give off an explosive
gas while charging. Charge battery in a well
ventilated area and keep away from an open
flame or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas
appliances.
The battery is sealed and is maintenance-free. Acid
levels cannot be checked and fluid can not be added.
•
Always keep the battery cables and terminals clean
and free of corrosive build-up.
After cleaning the battery and terminals, apply a
light coat of petroleum jelly or grease to both
terminals
Cutting Deck Removal
•
To remove the cutting deck, proceed as follows:
•
Place the PTO/Blade Engage lever in the
disengaged (OFF) position and engage the parking
brake.
•
Always keep the rubber boot positioned over the
positive terminal to prevent shorting.
•
•
Lower the deck by moving the deck lift lever into the
bottom notch on the right fender.
Remove the hairpin clip that secures the PTO cable
to the rear of the cutting deck. See Figure 20.
Remove the PTO cable and accompanying spring
from the cutting deck.
IMPORTANT: If removing the battery, disconnect the
NEGATIVE (Black) wire from its terminal first, followed
by the POSITIVE (Red) wire. When re-installing the
battery, always connect the POSITIVE (Red) wire to the
POSITIVE (+) terminal before connecting the
NEGATIVE (Black) wire to the NEGATIVE (-) terminal.
Be certain that the wires are connected to the correct
terminals; reversing them could change the polarity and
cause damage to your engine’s alternator.
Hairpin Clip
Spring
Jump Starting
WARNING: Never jump start a damaged or
frozen battery. Be certain the vehicles do not
touch, and ignitions are off. Do not allow cable
clamps to touch.
PTO Cable
•
•
•
•
Connect positive (+) cable to positive post (+) of
your tractor’s discharged battery.
Connect the other end of the (+) cable to the
positive (+) post of the jumper battery.
Connect the second negative (–) cable to the
negative (–) post of the jumper battery.
Make the final connection on the engine block of
the stalled tractor, away from the battery. Attach to
a unpainted part to assure a good connection.
Figure 20
•
•
Remove the deck belt from around the tractor’s
engine pulley.
Looking at the cutting deck from the left side of the
tractor, locate the deck support pin on the rear left
side of the deck.
IMPORTANT: If the jumper battery is installed on a
vehicle (i.e. car, truck), do NOT start the vehicle’s
engine when jump starting your tractor.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Pull the deck support pin outward to release the
Changing the Deck Belt
WARNING: Be sure to shut the engine off, engage
the parking brake and remove the ignition key to
prevent unintended starting before removing the belt.
WARNING: Avoid the possibility of a
pinching injury. Do not place your fingers on
the idler spring or between the belt and a
pulley while removing the belt.
All belts on your tractor are subject to wear and should
be replaced if any signs of wear are present.
Support Pin
IMPORTANT:The V-belts found on your tractor are
specially designed to engage and disengage safely. A
substitute (non-OEM) V-belt can be dangerous by not
disengaging completely. For a proper working machine,
use factory approved belts.
To change or replace the deck belt on your tractor,
proceed as follows:
Figure 21
•
•
•
Remove the belt keeper rod(s) from around the
engine pulley.
Remove the cutting deck as instructed earlier in this
section.
Remove the belt covers by removing the screws
that fasten them to the deck. Refer to the figure on
the following page.
Loosen, but do not remove the deck idler pulleys.
Remove the deck belt from around all pulleys,
including the deck idler pulleys.
Route the new belt as shown in the figure below
and retighten the deck idler pulleys.
Reinstall the belt guards removed earlier and
remount the deck to the tractor.
Route the belt around the engine pulley and
reinstall the belt keeper rod(s).
•
•
Repeat the above steps on the tractor’s right side.
Move the deck lift lever into the top notch to raise
the deck lift arms up and out of the way.
Gently slide the cutting deck toward the front of the
tractor allowing the hooks on the deck to release
themselves from the deck stabilizer rod.
•
•
Gently slide the cutting deck (from the right side)
out from underneath the tractor.
•
•
Changing The Transmission Drive Belt
•
•
•
NOTE: Several components must be removed and
special tools (i.e. air/impact wrench) used in order to
change the tractor’s transmission drive belt. See a Toro
Service Dealer to have your drive belt replaced.
Changing the Lower Deck Belt (Model LX460 only)
NOTE: Several components must be removed in
order to change the lower deck belt (Model LX460). See
a Toro Service Dealer to have this drive belt replaced.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
LX420
Belt Cover
Idler Pulleys
LX460
Belt Cover
Idler Pulleys
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11: OFF-SEASON STORAGE
Clean and lubricate the tractor as instructed in Section 7:
manual before storing for an extended period.
To empty the system, run the engine until the tank
and system are empty.
WARNING: Drain fuel only into an
approved container outdoors, away from an
open flame. Allow engine to cool. Extinguish
cigarettes, cigars, pipes, and other sources of
ignition prior to draining fuel.
Engine
If the engine will be out of service for two months or
more, use the following storage procedure:
•
•
Clean the exterior surfaces of the engine.
Change the oil and filter while the engine is still
warm from operation. Refer to Changing Engine Oil on
•
•
Remove the spark plug. Add one tablespoon of
engine oil into the spark plug hole. Install the plug,
but do not reconnect the plug wire. Crank the
engine two or three revolutions.
•
The fuel system must be completely emptied, or the
gasoline must be treated with a fuel stabilizer such
Store the engine in a clean, dry place.
®
as STA-BIL to prevent deterioration. If you choose
WARNING: Never store the machine or
fuel container indoors where there is an open
flame, spark or pilot light such as on water
heater, furnace, clothes dryer or other gas
appliance.
to use a stabilizer, follow the manufacturers
recommendations, and add the correct amount for
the capacity of the fuel system. Fill the fuel tank with
clean, fresh gasoline. Run the engine for 2-3
minutes to get stabilized fuel into the carburetor.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12: MAINTENANCE CHART
Before
Each Use
After Initial
24 Hours
Every
10 Hours
Every
25 Hours
Every
50 Hours
Every
Season
Prior
to Storing
Clean Hood/Dash Louvers
Check Engine Oil Level
Clean and Re-oil Air
Filter’s Foam Precleaner
Replace Air Filter Element
Change Engine Oil & Filter
Clean Battery Terminals
Lube Front Axles and Rims
Clean Engine Cooling Fins
Lube Pedal Pivot Points
Check Spark Plug
Check Safety Interlock
System
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 13: TROUBLESHOOTING
Trouble
Possible Cause(s)
Corrective Action
Engine fails to start
PTO (Blade Engage) lever engaged. Place PTO (Blade Engage) lever in (OFF) position.
Parking brake not engaged.
Spark plug wire disconnected.
Throttle/choke control not in correct
starting position.
Engage parking brake.
Connect wire to spark plug.
Move Throttle/Choke Control into CHOKE position.
Choke not activated
Fuel tank empty, or stale fuel.
Blocked fuel line.
Move Throttle/Choke Control into CHOKE position.
Fill tank with clean, fresh (less than 30 days old) gas.
Clean fuel line or replace fuel filter.
Faulty spark plug.
Clean, adjust gap or replace plug.
Engine flooded.
Crank engine with throttle in FAST position.
Move Throttle/Choke Control out of CHOKE position.
Connect and tighten spark plug wire(s).
Clean fuel line; fill tank with clean, fresh (less than 30
days old) gasoline. Replace fuel filter, if so equipped.
Clear vent or replace cap if damaged.
Engine runs erratic
Unit running with CHOKE activated.
Spark plug wire(s) loose.
Blocked fuel line or stale fuel.
Vent in gas cap plugged.
Water or dirt in fuel system.
Drain fuel tank. Refill with clean, fresh (less than 30
days old) gasoline.
Dirty air cleaner.
Replace air cleaner paper element or clean foam
precleaner.
Engine overheats
Engine oil level low.
Air flow restricted.
Fill crankcase with proper capacity and weight of oil.
Clean grass clippings and debris from around the
engine’s cooling fins and blower housing.
Remove spark plug and reset the gap.
Replace spark plug. Set plug gap.
Engine hesitates at high RPM Spark plug gap too close.
Idles poorly
Spark plug fouled, faulty or gap too
wide.
Dirty air cleaner.
Replace air cleaner element or clean pre-cleaner.
Tighten blade and spindle. Balance blade.
Replace blade.
Place throttle in FAST (rabbit) position.
Do not mow when grass is wet; wait until later to cut.
Mow once at a high cutting height, then mow again at
desired height or make a narrower cutting swath.
Sharpen or replace blade.
Excessive vibration
Cutting blade loose or unbalanced.
Damaged or bent cutting blade.
Engine speed too low.
Wet grass.
Mower will not mulch grass
Excessively high grass.
Dull blade.
Uneven cut
Deck not balanced properly.
Dull blade.
Perform side-to-side deck adjustment.
Sharpen or replace blade.
Uneven tire pressure.
Check tire pressure in all four tires.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 14: SPECIFICATIONS*
LX420
LX460
Capacities
Fuel Tank
3.0 gal. (11.4 liters)
50.75 oz. (1.5 liters)
3.0 gal. (11.4 liters)
50.75 oz. (1.5 liters)
Engine Crankcase (w/ filter)
Constant Velocity Transmission
Forward Speed
0 - 5.2 mph (8.2 km/h)
0 - 2.3 mph (3.7 km/h)
0 - 5.2 mph (8.2 km/h)
0 - 2.3 mph (3.7 km/h)
Reverse Speed
Engine (Air-cooled, 4-cycle)
Make
Kohler Courage
SV540
Kohler Courage
SV600
Model
Cylinders
Single
Single
Bore
3.50 in. (89 mm)
3.38 in. (86 mm)
32.6 cubic in. (535 cc)
18 HP (13.4 kW)**
3.70 in. (94 mm)
3.38 in. (86 mm)
36.4 cubic in. (597 cc)
20 HP (14.9 kW)**
Stroke
Displacement
Power @3600 RPM
Maximum Torque
32.1 ft. lb. (43.5 Nm)
@ 2200 RPM
36.9 ft. lb. (50.0 Nm)
@ 2200 RPM
Compression Ratio
Engine Speed (governed)
Low Speed
8.5:1
8.5:1
3375 RPM
3375 RPM
1500 RPM ( 75 RPM)
.030 in. (.76 mm)
2150 RPM ( 75 RPM)
.030 in. (.76 mm)
Spark Plug Gap
Electrical System
System Voltage
Battery
12-volt Negative Ground 12-volt Negative Ground
190 CCA (sealed)
15 Amp Regulated
20 Amp
190 CCA (sealed)
15 Amp Regulated
20 Amp
Alternator
Fuse (automotive type)
Headlights
Incandescent
Incandescent
Single Disc (Dry)
Single Disc (Dry)
Brakes
Turf Tires
Front (inches)
Rear (inches)
15 x 6 x 6
20 x 8 x 8
15 x 6 x 6
20 x 8 x 8
Dimensions
Cutting Width, Deck
Wheelbase
42 in. (106.7 cm)
46 in. (116.8 cm)
68 in. (172.7 cm)
45 in. (114.3 cm)
43 in. (109.2 cm)
4.5 in. (11.4 cm)
18 in. (46 cm)
46 in. (116.8 cm)
46 in. (116.8 cm)
68 in. (172.7 cm)
48 in. (127.9 cm)
43 in. (109.2 cm)
4.5 in. (11.4 cm)
18 in. (46 cm)
Length, over all
Width, over all
Height, over all
Ground Clearance
Turning Radius
Weight (approximate)
498 lb. (225.9 kg)
501 lb. (227.25 kg.)
* Toro reserves the right to change product specifications, design, and standard equipment without notice and without incurring obligation
** Kohler’s horsepower ratings exceed Society of Automotive Engineers Small Engine Test Code J1940. Actual engine horsepower is lower and
affected by, but not limited to, accessories (air cleaner, exhaust, charging, cooling, fuel pump, etc.), application, engine speed and ambient
operating conditions (temperature, humidity, and altitude).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and MTD Consumer Group Inc are pleased to explain the evaporative emission control system warranty on your 2006 lawn
mower. In California, new lawn mower must be designed, built and equipped to meet the State’s stringent anti-smog standards. MTD Consumer Group Inc must
warrant the EECS on your lawn mower for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your lawn mower.
Your EECS may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps, valves,
canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your lawn mower at no cost toyou including diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:
This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be
repaired or replaced by MTD Consumer Group Inc.
OWNER’S WARRANTY RESPONSIBILITIES:
As the lawn mower owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD Consumer Group Inc recom-
mends that you retain all receipts covering maintenance on your lawn mower, but MTD Consumer Group Inc cannot deny warranty solely for the lack of receipts.
As the lawn mower owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if your lawn mower or a part has failed
due to abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your lawn mower to MTD Consumer Group Inc’s distribution center or service center as soon as the problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should
contact the MTD Consumer Group Inc Service Department at 1-800-800-7310.
GENERAL EMISSIONS WARRANTY COVERAGE:
MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the lawn mower is: Designed, built and equipped so as to
conform with all applicable regulations; and free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material
respects to that part as described in MTD Consumer Group Inc’s application for certification.
The warranty period begins on the date the lawn mower is delivered to an ultimate purchaser or first placed into service. The warranty period is two years.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for the warranty period
stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD Consumer Group Inc according to subsection
(4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period.
2. Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such
part repaired or replaced under warranty will be warranted for the remaining warranty period.
3. Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period of time before the
first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part will be repaired or replaced by MTD Consumer
Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the
first scheduled replacement point for the part.
4. Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge to the owner.
5. Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to service the subject
engines or equipment.
6. The lawn mower owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-related warranted part,
provided that such diagnostic work is performed at a warranty station.
7. MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under warranty of any warranted
part.
8. Throughout the lawn mower warranty period stated above, MTD Consumer Group Inc will maintain a supply of warranted parts sufficient to meet the expected
demand for such parts.
9. Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will
not reduce the warranty obligations of MTD Consumer Group Inc.
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the
ultimate purchaser will be grounds for disallowing a warranty claims. MTD Consumer Group Inc will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group
Inc demonstrates that the lawn mower has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the
direct cause of the need for repair or replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly
operating, adjustment limiting device is still eligible for warranty coverage. The following emission warranty parts list are covered: Fuel Line, Fuel Line Clamps
Download from Www.Somanuals.com. All Manuals Search And Download.
The Toro Company
MANUFACTURER’S LIMITED WARRANTY FOR
LAWN & GARDEN TRACTORS
IMPORTANT: To obtain warranty coverage owner must present an original
Without limiting the foregoing, this limited warranty does not provide coverage
proof of purchase and applicable maintenance records to the servicing dealer.
Please see the operator’s manual for information on required maintenance and
service intervals.
in the following cases:
a. The engine or component parts thereof. These items may carry a separate
manufacturer’s warranty. Refer to applicable manufacturer’s warranty for
terms and conditions.
The limited warranty set forth below is given by The Toro Company (“Toro”)
and The Toro Warranty Company, pursuant to an agreement between them,
with respect to new merchandise purchased or leased and used in the United
States and/or its territories and possessions, and by Toro with respect to new
merchandise purchased or leased and used in Canada and/or its territories and
possession.
b. Routine maintenance items such as lubricants, filters, blade sharpening,
tune-ups, brake adjustments, clutch adjustments, deck adjustments, and
normal deterioration of the exterior finish due to use or exposure.
c. Service completed by someone other than an authorized service dealer.
d. Toro does not extend any warranty for products sold or exported outside
of the United States and/or Canada, and their respective possessions and
territories, except those sold through Toro’s authorized channels of export
distribution.
Toro warrants this product (excluding its Normal Wear Parts and Batteries
as described below) against defects in material and workmanship for a
period of two (2) years or eighty (80) operation hours, whichever comes
first, commencing on the date of original retail purchase or lease and will, at
its option, repair or replace, free of charge, any part found to be defective in
materials or workmanship.
e. Replacement parts and/or accessories that are not genuine Toro parts.
f. Transportation charges and service calls.
Normal Wear Parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of original purchase
or lease. Normal wear parts include, but are not limited to items such as: belts,
blades, blade adapters, grass bags, rider deck wheels, seats, and tires.
g. Toro does not warrant this product for commercial use.
There are no implied warranties, including without limitation any implied
warranty of merchantability or fitness for a particular purpose. No
warranties shall apply after the applicable period of express written
warranty above. No other express warranties beyond those mentioned
above, given by any person or entity, including a dealer or retailer, with
respect to any product, shall bind Toro. The exclusive remedy is repair or
replacement of the product as set forth above. The terms of this warranty
provide the sole and exclusive remedy arising from the sale and/or lease
of the products covered hereby. Toro shall not be liable for any incidental
or consequential loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services or for rental
expenses to temporarily replace a warranted product.
Batteries have a one-year prorated limited warranty against defects in material
and workmanship, with 100% replacement during the first three months. After
three months, the battery replacement credit is based on the months remaining
in the twelve (12) month period dating back to the original date of original sale
or lease. Any replacement battery will be warranted only for the remainder of
the original warranty period.
This limited warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse, commercial use, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire, water, or
damage because of other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not approved by Toro
for use with the product(s) covered by this manual will void your warranty as
to any resulting damage. In addition, Toro may deny warranty coverage if the
hour meter, or any part thereof, is altered, modified, disconnected or otherwise
tampered with.
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts,
so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for loss,
damage, or injury to you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF
PURCHASE AND APPLICABLE MAINTENANCE RECORDS, through your
local authorized service dealer. To locate the dealer in your area:
This limited warranty shall not extend lo anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
In the U.S.A. or Canada:
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty
gives you specific legal rights, and you may also have other rights that vary in
different jurisdictions.
Check your Yellow Pages, or contact The Customer Care Department,
The Toro Warranty Company at 8111 Lyndale Avenue South,
Bloomington, MN 55420-1196, call in the U.S. 1-888-384-9942
Customer Care Department of The Toro Warranty Company, 8111 Lyndale Ave. South,
Download from Www.Somanuals.com. All Manuals Search And Download.
|
