www.timex.com
W-213 157-095000 NA
THANK YOU FOR PURCHASING YOUR TIMEX® STOPWATCH.
Please read instructions carefully to understand how to operate your Timex® stopwatch.
FEATURES AND BASIC OPERAT I O N
•
•
•
•
•
•
•
•
•
•
•
•
Time of day with 12- or 24-hour format
Day and date
2nd time zone
Optional hourly chime
24-hour chronograph with memory for 50 laps in multiple runs
Chronograph recall with date stamp, best lap, and average lap time for each run
Optional 10-second auto-start for chronograph
Speed calculation
24-hour countdown timer (count down and count up or repeat)
Pacer
7 weekly alarms and one daily alarm
INDIGLO® night-light with NIGHT-MODE® feature
Press MODE repeatedly to step through modes: Time, Chrono, Speed, Recall, Timer, Pacer, Weekly
Alarm, and Daily Alarm. Unit displays mode name for 2 seconds before switching to mode shown.
AC T I VAT I O N
Unit is shipped in “OFF” mode to preserve battery life. To activate unit, press and hold all five
buttons simultaneously until STOP indicator disappears, about 4 seconds. When buttons are
released, unit is ready for use.
TIME
Time mode provides time and date like a digital watch. Press MODE repeatedly until TIME appears.
To set time and date:
1) Press and hold RESET/ADJUST. Seconds flash. Press START/STOP to round time up or down to
nearest minute, setting seconds to zero.
2) Press MODE. Minutes flash. Press START/STOP to change minutes; hold button to scan values.
3) Press MODE. Hour flashes. Press START/STOP to change hour (including AM/PM).
4) Press MODE. Day flashes. Press START/STOP to change day.
5) Press MODE. Month flashes. Press START/STOP to change month.
6) Press MODE. Year flashes. Press START/STOP to change year.
7) Press MODE. Time format flashes. Press START/STOP to select 12- or 24-hour time format
(selected format will be used in all modes). 12-hour format has AM/PM.
8) Press RESET/ADJUST, at any step, when done setting.
Press and hold LAP/NEXT to see TIME 2, a 2nd time zone. “TIME 2” appears on display. Continue
holding button to switch time and date to TIME 2. After switching, set TIME 2 using procedure
above. Press and hold LAP/NEXT to see or switch back to home time from TIME 2.
Press START/STOP to turn hourly chime on/off. When on, bell icon
on every hour.
appears and unit chimes
CHRONOGRAPH
This mode provides a chronograph (stopwatch) function. This mode is only available when Speed
mode is not in use. Press MODE repeatedly until CHRONO appears.
To start, press START/STOP. Chrono counts up by hundredths of a second. Hours are shown in
upper right part of display (“00H” initially).
To stop, press START/STOP. To resume, press START/STOP again.
While chrono is running, press LAP/NEXT to take a lap/split. Lap time is displayed with lap number
for 9 seconds, while chrono continues to run.
At end of run, press START/STOP. Last lap time is displayed for 9 seconds followed by total time.
Press LAP/NEXT or RESET/ADJUST to immediately display total time.
Once chrono is stopped and total time is displayed, to store run and go to next (new) run, press
and hold LAP/NEXT, or to reset chrono (clear last run), press and hold RESET/ADJUST. Run number
is shown in upper right part of display. Stored runs may be recalled in Recall mode, described
below.
Auto-Start - Chrono may be started automatically after a 10-second countdown. When chrono is
reset (zero), press RESET/ADJUST to turn auto-start feature on/off. “AUTO” appears at bottom of
display when feature is on. Press START/STOP to begin countdown. Unit beeps once every second
followed by one long beep when chrono is started.
Chrono continues to run if you exit mode.
NOTES:
•
•
To see amount of remaining memory, when chrono is reset (zero), press and hold LAP/NEXT.
Chrono counts up to 24 hours and starts over at zero.
SPEED
Speed mode calculates speed of individual laps. This mode is only available when chrono is reset
(zero). Press MODE repeatedly until SPEED appears.
To use Speed mode, you must set lap distance:
1) Press and hold RESET/ADJUST. 1/100 mile digit flashes. Press START/STOP to change value;
hold button to scan values.
2) Press MODE. 1/10 mile digit flashes. Press START/STOP to change value.
3) Use MODE and START/STOP as above to set other digits.
4) Press RESET/ADJUST, at any step, when done setting.
Mode operates like Chrono mode, except speed is displayed briefly when timing is stopped or
lap/split is taken. When run is stored, speed data is included. See RECALL section.
RECALL
Recall mode allows you to view data of stored runs from Chrono or Speed mode. This mode is
only available when stopwatch is not running. Press MODE repeatedly until RECALL appears.
Upon mode entry, amount of remaining memory is displayed.
If no data is stored, “NO DATA” is displayed. Otherwise, last run is displayed. Run number and date
of run are shown.
To select another run to recall, press LAP/NEXT. This may be done at any point in recall sequence.
To recall run, press START/STOP repeatedly to step through data: run date, lap distance (if run was
done in Speed mode), lap times, total time, best lap time, and average lap time. If run was done in
Speed mode, speed is shown alternating with the lap times.
To delete run from memory, press and hold RESET/ADJUST. To clear all of memory, continue
holding RESET/ADJUST.
TIMER
Timer mode provides a countdown timer with alert. Press MODE repeatedly until TIMER appears.
To set countdown time:
1) Press and hold RESET/ADJUST. Seconds flash. Press START/STOP to change seconds; hold
button to scan values.
2) Press MODE. Minutes flash. Press START/STOP to change minutes.
3) Press MODE. Hours flash. Press START/STOP to change hours.
4) Press LAP/NEXT, at any step, to select action at end of countdown, repeat
5) Press RESET/ADJUST, at any step, when done setting.
or count up
.
To start timer, press START/STOP.
To pause countdown, press START/STOP. To resume countdown, press START/STOP, or to reset
countdown, press LAP/NEXT when timer is stopped.
Watch beeps when countdown ends (timer reaches zero). Press any button to silence. If no button
is pressed, alert will sound for 20 seconds. If timer was set to repeat, timer repeats countdown
indefinitely. Otherwise, it begins counting up.
Timer continues to run if you exit mode.
ownload from Www.Somanuals.com. All Manuals Search And Downloa
|