Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR
BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The graphic symbols on the back cover of the set mean the following:
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing) in-
structions in the literature accompanying the appliance.
WARNING :
•
•
•
•
To reduce the risk of fire or electric shock, do not expose this appliance to rain or
moisture.
The apparatus shall not be exposed to dripping or splashing, No objects filled
with liquids, such as vases, shall be placed on the apparatus.
The mains plug is used as the disconnect device, the disconnect device shall remain
readily operable.
In order to disconnect the apparatus from the mains completely, the mains plug should
be disconnected from the mains socket outlet completely.
INSTALLATION
LOCATE the receiver in the room where direct light does not strike the screen. Total darkness
or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recom-
mended for comfortable viewing.
ALLOW enough space between the receiver and the wall to permit proper ventilation.
AVOID excessive warm locations to prevent possible damage to the cabinet or component
failure.
CONNECTION
This TV receiver is connected to AC: 220-240V~ 50Hz .
AUTOMATIC DEGAUSSING
All colour television receivers are sensitive to magnetic influences, usually caused by either
moving the receiver from one place to another or using certain electrical appliances near the
receiver. This residual magnetism as it is called, sometimes causes distortion which gives rise
to "blotchy" areas of colour in the picture. To avoid these effects the receiver incorporates an
automatic degaussing circuit which operates for a short while immediately each time the
receiver is switched on using the mains switch. This circuit removes any residual magnetism in
the metal parts of the picture tube and therefore ensures that each time the receiver is switched
lifelike. If the set is moved or faced in a different direction, the mains switch must be switched
off at least 10 minutes in order that the automatic degaussing circuit operates properly.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
CAUTION
Never tamper with any components inside your set, or any other adjustment controls not
mentioned in this manual. All television receivers are high voltage instruments. Your PICTURE
TUBE is a highly vacuum. If broken, glass fragments will be violently expelled. Scratching,
Chipping or undue pressure is dangerous and should be avoided. When you clean the PICTURE
TUBE FACE or CABINET, the power cord should be removed from the wall socket then wipe the
receiver with a dry soft cloth. All "inside work" on your receiver must only be performed only
by the Professional Service Personnel.
DANGER
LASER SAFETY
This unit employs an optical laser beam system in the CD
mechanism,designed with built in safeguards. Do not attempt
to disassemble, refer to qualified service personnel.
Exposure to this invisible laser light light beam may be harmful
to the human eye.
THIS IS A CLASS-1 LASER PRODUCT. USE OF CONTROLS,
Invisible laser radiation when open
ORADJUSTMENTSORPROCEDURESOTHER THANTHOSE
and interlock failed or defeated.
SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS LA-
avoid direct exposure to laser beam.
SER LIGHT BEAM EXPOSURE.
Manufactured under license from Dolby Laboratories “Dolby”,”Pro Logic”and the double-D
symbol are trademarks of Dolby Laboratories. Confidential unpublished works.© 1992-1997
Dolby Laboratories,lnc.All rights reserved.
This product incorporates copyright protection technology that is protected by U.S. pat-
ents and other intellectual property rights. Use of this copyright protection technology
must be authorized by Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse engineering or disas-
sembly is prohibited.”
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS
1. Speaker
2. Power Button
3. Channel Buttons
4. Menu Button
5. TV/AV/DVD Button
6. DVDDoor
7. Remote Sensor
8. DVD Stop Button
9. DVD Play Button
10. Volume -/+ Buttons
11. DVD Open/Close Button
12. Side Audio (R) Input (AV 2)
13. Side Audio (L) Input (AV 2)
14. Side Video Input (AV 2)
15. Earphone Jack
16. 75 ohm Antenna Socket
17. Back Video/Audio Output
18. Back Video/Audio Input(AV 1)
19. Audio digital Out Socket (For DVD only)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS
1. TV/AV Button
2. STANDBY Button
3. Numberic Buttons
4. TV Menu/Navigation Arrows Buttons
5. Channel Buttons
6. DVD Navigation Up Button
7. DVD Navigation Left Button
8. DVD Enter Button
9. DVD Menu Button
10. Pause/Step Button
11. Play Button
12. Stop Button
13. Zoom Button
14. Repeat Button
15. Subtitle Button
16. Search Button
17. Setup Button
18. Clear Button
19. Program Button
20. DVD/TV Button
21. Open/Close Button
22. Sleep Button
23. TV Display Button
24. Mute Button
25. PP Button
26. Volume Up/Down Buttons
27. DVD Navigation Right Button
28. DVD Navigation Down Button
29. DVD +10 Button
30. Fast forward Button
31. Fast backward Button
32. Next Button
33. Previous Button
34. Angle Button
35. Repeat A-B Button
36. Audio Button
37. DVD Display Button
38. Slow Play Button
BATTERYINSTALLATION
•
•
Insert two pcs "AAA" Alkaline "LR03" batteries as illustrated and replace the battery cover.
Batteries included.
CAUTION
•
Do not attempt to recharge, short-circuit, disassemble,
heat or throw the batteries into the fire.
•
Placement with wrong or mixed polarities will result in
damage to the batteries and /or may result in a
malfunction of the unit.
•
•
•
Do not mix old and new batteries.
Dispose used batteries with care.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATINGTHETELEVISION
Connect your TV aerial to the aerial input socket located on the back of the TV.
Push the Main Power Switch, Power Indicator will be illuminated. After a few seconds the TV
screen will light up and will show interference on the screen. The TV will require tuning into the
available TV stations in your area.
TUNE
C SYSTEM
S SYSTEM
PROGRAM
AUTO SEARCH
MANUAL SEARCH
PAL
BG
1
Pre-setting the TV stations into the Memory
(Note: Preset tuning can only be carried out in TV Mode)
Press MENU three times on the remote handset, the TV
screen will show TUNE mode as FIG.1
/
/
:SELECT
ADJUST
FIG.1
TUNE
C SYSTEM
S SYSTEM
PROGRAM
PAL
BG
1
AUTO SEARCH
1. Press the Navigation button
mode as shown in FIG. 2
to select the AUTO SEARCH
AUTO SEARCH
MANUAL SEARCH
2. Press the Navigation button to start the automatic
scanning process starting from VHF to UHF
and the TV stations will automatic store into the memory as
shown in FIG. 3
/
/
:SELECT
:ADJUST
FIG.2
AUTO SEARCH
PROGRAM
•
When scanning is completed, the set will tune to lowest
programme and show lowest programme number on the
screen.
1
BAND
VHF L
•
•
To stop auto search function to press MENU button.
To exit the TUNE mode, press the MENU button.
FIG.3
TUNE
MANUAL SEARCH
CSSSYYSSTTEEMM
PAL
BG
1
1. Press the Navigation
/
button to select the PROGRAMME.
button to select the desired
Then press the Navigation
Programme number.
/
PROGRAM
AUTO SEARCH
MANUAL SEARCH
2. Press the Navigation
/
button to select the MANUAL
button
/
/
:SELECT
:ADJUST
SEARCH mode and press the Navigation
/
to start the search up the band. The TV screen will show
the tuning and when the first station received is located,
the tuning will stop and be stored automatically. Then press
FIG.4
MANUAL SEARCH
PROGRAM
the Navigation
/
button to recommence seek search to
1
BAND
VHF L
the next TV station, as shown in FIG.4 and FIG.5.
3. Press the MENU button to exit the manual.
FIG.5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
C. SYSTEM
1. Press the Navigation
/
button to select the C SYSTEM then press Navigation / button to
change the desired colour system PAL, NTSC, AUTO.
S SYSTEM
1. This unit is the single sound system, it is fixed cannot be adjust.
Notes:
1. If ghost / noisy stations have been stored when using the AUTO SEARCH method, these can
be removed from the channel list by entering the SKIP Mode shown in the TUNE menu. Press
and change the OFF state to ON. Press the MENU button to return to
/
the Navigation
normal viewing. The unwanted station will be removed from the channel list when you
change TV channels.
The SKIPPED station can be restored by re entering the TUNE menu and changing the SKIP ON
status to OFF.
2. To exit the TUNE mode, press MENU button.
PICTURE
PICTURE
CONTRAST
BRIGHTNESS
COLOUR
50
50
50
50
1. Press the MENU, TV screen will show PICTURE mode.
2. Press the Navigation button to select the CONTRAST
/BRIGHTNESS /COLOUR / SHARPNESS as show in FIG. 6.
3. Press the Navigation button to the desired level, The
level can be adjust from 0 ~ 99.
To exit the PICTURE Mode, press the MENU three times.
/
SHARPNESS
/
/
: SELECT
: ADJUST
/
FIG.6
•
SET UP LANGUAGE
SETUP
1. Press the MENU button twice to select the SETUP, as
shown in FIG.7.
LANGUAGE
BLUE BACK
EXCHANGE
ENGLISH
ON
1
- - -
2. Press the Navigation button
then press the Navigation
/
/
to select the LANGUAGE,
to select the desired lan-
/
/
: SELECT
: ADJUST
guage ENGLISH, FRANCAISE, ESPANOL, PORTUGUES,
NEDERLANDS, ITALIANO, DEUTSCH.
FIG.7
BLUE BACK
Press the Navigation
/
button to select the BLUE BACK and press the Navigation
/
button
to adjust the blue Back-ground on or off.
EXCHANGE
After storing TV stations by AUTO SEARCH or MANUAL SEARCH, the position of each TV
programme can be changed by the following method:
1. In the existing watching station press the Navigation button to select the EXCHANGE then
press the numaric buttons to Key in the desired programme no. which you want to move this
station to, then press the Navigation to confirm.
2. To exit the SETUP MODE, press the MENU button 2 times.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL SELECT AND VOLUME CONTROL
1) Press CHANNEL
/
buttons to select TV station.
0
255
Press CHANNEL." ", the programme
no. will appear on the top right corner
and change from a higher to lower
number.
Press CHANNEL. " ", the programme no.
will change from a lower no. to higher
number.
2) Press VOLUME
/
button to adjust sound level.
VOLUME
| | | |
06
TV/AV/DVD Mode Button
•
If video/audio input socket are in use, press TV/AV/DVD Mode button in the TV set, "AV1"
OR "AV2" will display on the top right corner of the screen.
•
Press TV/AV/DVD button to turn on DVD in the TV set. When DVD mode is selected please
wait, the screen will be dark as it will take a few seconds to show the “DVD “at the top right
corner of the screen.
TV
AV 1
AV 2
DVD
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. REMOTE CONTROL OPERATION
CHANNEL Up and Down buttons
Press the CHANNEL
or
button to select a higher or lower channel number.
0~9 Numberic Button
To select a TV station using A buttons 0~9.
For example:
Press number “9” button to select PROGRAMME “9”.
Two digit Programme Number
l
l
For example:selecting PROGRAMME “12”
1. Press the -/-- button, on screen will show --.
2. Press the number “1” button, on screen will show “1-”.
3. Press the number “2” button, channel “12” will show.
Three digit Programme number
For example:selecting PROGRAMME “123”
1. Press the -/-- button twice, on screen will show ---.
2. Press the number “1” button, on screen will show “1--”.
3. Press the number “2” button, on screen will show “12-”.
4. Press the number “3” button, on screen will show “123”.
PP Button(personal preference)
Press PP button to select the picture effect.
l
Personal
MILD
STANDARD
VIVID
SLEEP Button
Press the SLEEP button to select a predetermined time when the TV will turn off. The sleep time
can be set to count down from 5 to 120 minutes.
STANDBY Button
l
Press the STANDBY button to switch the picture and sound ON/OFF.
MUTE Button
l
Press the Mute button to switch OFF the sound, press once again to switch ON the sound.
TV/AV Button
l
Press the TV/AV mode button to select VIDEO mode. Press again to go back to TV mode.
DVD/TV Button
l
Press the DVD/TV mode button to select DVD mode. Press again to go back to TV mode.
(There will be a few seconds delay before entering the DVD mode).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDPLAYER OPERATION
Basic Operation
1. Press “TV/AV/DVD” button on the unit or press the DVD MODE direct key on the remote
handset to turn ON DVD.
2. Press “OPEN / CLOSE (EJECT)” button to load disc in disc tray.
3. Press “OPEN / CLOSE” button to close the tray.
•
Hold the disc without touching either of its surfaces, position it with the printed title side
facing up.
Play Discs
1. Press the OPEN/CLOSE Button on the front panel and load the Disc on the tray.
The label side should be facing upwards. For a Double-sided DVD Disc, put the disc with label
A/1 up.
2. Press the OPEN/CLOSE button again to close the tray and the disc will be loaded.
3. The Disc will be played automatically.
•
•
If it is a DVD disc, it will show the Menu/Title Page on the screen.
If it is a CD, it will play the first track directly.
4. Press the STOP Button if you want to stop the Disc playback. You can resume playback by
pressing the PLAY button and it will start at the location where you have pressed stopped
(Resume Play).
5. Press the STOP Button twice to have the Disc really stopped.
|| (Pause)/ Step
This function is applicable for DVD and CD audio.
•
•
For DVD, the picture will become static.
For CD audio, it will become silent.
1. Press the ( || ) Button will cause the player to enter PAUSE/STEP mode.
2. Press the PLAY Button again will resume to Play State.
DVD Setup Mode
•
•
•
Setup Mode provides the menu for the configuration of General setup page, Speaker setup
page, Dolby Digital setup, Preference page.
Item selection in the SETUP menu is done by using the Navigation Arrow and the ENTER
button.
To exit the SETUP Mode to press the SETUP button again.
Note: To setup the TV display mode must be in stop mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD
There are 5 OSDlanguages embedded in theDVD Player : English, French, German, Italian, Spanish.
1. Press the SETUP button on the remote controller to enter the setup menu GENERAL SETUP
PAGE.
2. Go to the OSD LANG option and use the Navigation Arrows to do the selection.
3. Press ENTER to confirm.
DVD Menu
The DVD Menu Play function is only applicable for DVD movie. User can access the Casting
information, Production History, Movie Introduction etc. directly through this function.
1. Press theDVD MENU Button on the remote controller to enter the Root Menu.
2. Use the Navigation Arrows (
do the selection.
) or input the item index through the Number keys (0-9) to
3. Press ENTER to confirm the selection.
Audio
This function is applicable for DVD and CD audio but with different effects.
Pressing the AUDIO Button will change the Audio channel.
•
Scan (
)
This function is applicable for DVD and CD audio but with different effects. The FAST FORWARD
key and FAST BACKWARD key are used to achieve fast play function.
•
For DVD, there are 5 different levels of speed (2x, 4x, 8x, 16x, 32x). Every successive key
press will increment the speed of quick play.
•
For CD audio, the FORWARD/BACKWARD will perform quick rolling on the music output.
Note : Press PLAY Button at any stage will resume to normal speed.
Prev. / Next (
)
During playback, press one of the PREV./NEXT buttons (PREVIOUS button and NEXT button)
•
•
When the PREV. button is pressed once, the pickup returns to the beginning of the PREVI-
OUS playing chapter or track.
When the NEXT button is pressed once, the pickup will go to the beginning of next chapter
or track.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow
The Slow Forward is applicable for DVD. There are 4 steps of slow motion speed, 1/2, 1/4, 1/8,
1/16. Successive key presses will decrement the playback speed.
Note : Press Play Key to switch back to normal playback speed.
Repeat Mode
This function is applicable for DVD and CD audio but with different effects.
•
For DVD disc playback, user can choose to repeat the current chapter, the current title or disc.
Subsequent key press of the REPEAT key can change between these four options.
For CD, user can choose to repeat the current track or the whole disc (Repeat All). Subse-
quent key press of the REPEAT key can change between these three options.
•
Repeat AB
This function is applicable for DVD and CD audio. User can specify the repeating interval by
marking the starting point and the end point.
1. Press the REPEAT AB Button to mark the starting point. (Playback will continue).
2. Press the REPEAT AB Button to mark the end point. (The marked part will be repeated
automatically)
Note : Press the REPEAT AB Button during repetition will disable the Repeat mode.
Subtitle
This function is only applicable for DVD disc. It can change the subtitle language shown on the
screen.
Note : Number of subtitle available depends on the DVD disc.
Angle
Some discs may have multiple viewing angles during production. The ANGLE button is to select
the viewing angle shown on the screen.
Note : The number of Angle of View depends on the Disc.
Search
This function is applicable for DVD and CD audio. Through this function, the user can access a
specific location or a specific track by key in the target time or the track number.
1. Press the SEARCH Button Enter to search mode .
2. Input the target time though the number button (0~9) and the player will jump to the target
Location immediately.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Display (Remain Time)
This function is applicable for DVD only. It will display the timing information of the playback on
the screen.
•
For DVD playback, subsequent key press on the DISPLAY Button will show the Title
Elapsed Time, Title Remain Time, Chapter Elapsed Time and Chapter Remain Time one by
one.
TITLE ELAPSED
Press the DISPLAY Button
TT 01/04 CH 01/12 0:02:13
TITLE REMAIN
Press the DISPLAY Button
TT 01/04 CH 01/12 1:33:30
CHAPTER ELAPSED
TT 01/04 CH 01/12 0:02:15
Press the DISPLAY Button
CHAPTER REMAIN
Press the DISPLAY Button
Press the DISPLAY Button
TT 01/04 CH 01/12 0:02:18
DISPLAY OFF
Resume Play
This function is applicable for DVD and CD audio. During the disc playback, when the STOP
Button is pressed once, the player will enter the Resume Play mode. At this time, if the PLAY
Button is pressed, the player will resume playback at the location where the STOP Button is
pressed. If the STOP button is pressed (i.e. STOP Button is pressed twice), the player will be
Stop.
Zoom
This function is applicable for DVD. User can enlarge or reduce a static picture or a moving
picture by pressing the ZOOM buttons. There are 3 levels of zooming (2x, 3x, 4x) and they
can be achieved one by one through subsequent key presses on the ZOOM button.
NOTE: User can select the portion of the picture to be enlarged by using the Navigation
buttons (
).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Mode
This function is applicable for DVD and CD audio. User can assign the playback sequence according
to his/her preference. For CD audio, user can assign the track sequence while for DVD disc, user
can assign both the Title and Chapter sequence.
PROGRAM
01
02
03
04
05
06
07
08
09
10
1. Press the PROGRAM button. The Program Se-
quence table will be shown on the screen.
EXIT
NEXT
PROGRAM
2. Enter the track numbers according to the user
preference through the Number keys (0-9).
05
03
08
01
02
03
04
05
06
07
08
09
10
EXIT START NEXT
3. After assigning the playback sequence, move
the highlight cursor to the START option by using
the Navigation Arrows.
PROGRAM
Press ENTER on the remote controller to confirm.
05
03
08
01
02
03
04
05
06
07
08
09
10
To Remove the program
EXIT STOP NEXT
move the highlight cursor to desire Program By use
the Navigation arrows then press the clear button to
Remove the selected program.
Picture CD
Digital picture (JPEG) from a digital camera can be burnt on to a disc and played on this TV. Insert
a picture CD into the tray and the disc will be loaded automatically. If the disc type can be identified,
the player will start showing the pictures one by one (Slide Show Mode).
Operations
During Slide Show Mode: -
•
Press the STOP Button will shift to the Digest Mode in which 6 pictures files will be shown on
the screen each time.
•
Press the PAUSE Button will freeze the screen so that the current picture can be held for a long
time. To resume the slide show mode, press PLAY Button.
•
•
Press the NEXT Button on the remote controller will skip the next picture.
Press the PREVIOUS Button on the remote controller will repeat the current picture.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TV SECTION
Receiving Channels
VHFL
CH 2 - 4
VHFH
CH 5 - 12
UHF
CH 21- 69
Tuner Type
255 Channel, VS TUNING
DVD SECTION
Laser Wave length
Laser power
655nm
Class 1
Signal System
PAL/NTSC output
Coaxial digital output; pin jack
Digital audio output
Headphone
Stereo in DVD mode
Mono in TV mode
GENERAL SECTION
AC Power Input
AC Power Consumption
Speaker
AC 220-240V~50 Hz
74W
3” 8ohm x 2
Audio Output
1.5 W + 1.5 W
L385 x W375 x H370 (mm)
10.6 Kg
Dimensions
Net Weight
v Design and specifications are subject to change without notice.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC MAINTENANCE
Handling Discs:
- Hold the disc by the edges so the surface will not be soiled with finger prints. (Fig. A)
- Do not scratch the disc. Do not write on the label side with a pen.
- Be careful not to drop or bend the disc.
- Do not place more than 1 disk in the tray.
- Do not try to close the disc tray when the disc is not installed in the tray properly. (Fig. B)
- Be sure to store the disc in a disc case after playback.
- Keep the disc away from direct sunlight, heat sources, humid or dusty areas.
Cleaning Discs:
- If the surface of the disc is soiled, wipe the disc outwards from the center with a soft,
damp (water only) cloth. (Fig. C)
NOTE: (If you wipe the discs in a circular motion, circular scratches are likely to occur,
which will cause noise.)
- Do not use any type of solvent such as thinner, benzine, commercially available cleaners
or antistatic spray.
- If the disc is brought from a cold to a warm environment, moisture may form on the disc.
Wipe this moisture off with a soft, lint-free cloth before using the disc.
NOTE: CDR and CDRW discs recorded in CD Audio format are also playable.
CAUTION!
CDR/CDRW discs recorded using a personal computer or a CD recorder may not play if the
disc is damaged or dirty, or if there is dirt or condensation on the player’s lens.
If you record a disc using a personal computer, even if it is recorded in a compatible format,
there are cases in which it may not play because of the settings of the application software
used to create the disc. (Check with the software publisher for more detailed information.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|