TMS320DM643x DMP
DDR2 Memory Controller
User's Guide
Literature Number: SPRU986B
November 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preface ............................................................................................................................... 6
1
Introduction................................................................................................................ 7
1.1
1.2
1.3
1.4
1.5
Purpose of the Peripheral....................................................................................... 7
Features ........................................................................................................... 7
Functional Block Diagram....................................................................................... 8
Supported Use Case Statement ............................................................................... 8
Industry Standard(s) Compliance Statement................................................................. 8
2
Peripheral Architecture................................................................................................ 9
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Clock Control ..................................................................................................... 9
Memory Map .................................................................................................... 10
Signal Descriptions ............................................................................................. 11
Protocol Description(s)......................................................................................... 12
Memory Width and Byte Alignment .......................................................................... 20
Endianness Considerations ................................................................................... 21
Address Mapping ............................................................................................... 22
DDR2 Memory Controller Interface .......................................................................... 26
Refresh Scheduling ............................................................................................ 29
2.10 Self-Refresh Mode.............................................................................................. 29
2.11 Reset Considerations .......................................................................................... 30
2.12 VTP IO Buffer Calibration ..................................................................................... 31
2.13 Auto-Initialization Sequence................................................................................... 31
2.14 Interrupt Support................................................................................................ 34
2.15 DMA Event Support ............................................................................................ 34
2.16 Power Management............................................................................................ 34
2.17 Emulation Considerations ..................................................................................... 35
Supported Use Cases ................................................................................................ 36
3
4
3.1
Connecting the DDR2 Memory Controller to DDR2 Memory............................................. 36
3.2
DDR2 Memory Controller Registers ............................................................................. 40
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
SDRAM Status Register (SDRSTAT)........................................................................ 41
SDRAM Bank Configuration Register (SDBCR)............................................................ 42
SDRAM Refresh Control Register (SDRCR)................................................................ 44
SDRAM Timing Register (SDTIMR).......................................................................... 45
SDRAM Timing Register 2 (SDTIMR2)...................................................................... 46
Peripheral Bus Burst Priority Register (PBBPR) ........................................................... 47
Interrupt Raw Register (IRR).................................................................................. 48
Interrupt Masked Register (IMR) ............................................................................. 49
Interrupt Mask Set Register (IMSR).......................................................................... 50
4.10 Interrupt Mask Clear Register (IMCR) ....................................................................... 51
4.11 DDR PHY Control Register (DDRPHYCR).................................................................. 52
4.12 VTP IO Control Register (VTPIOCR) ........................................................................ 53
4.13 DDR VTP Register (DDRVTPR).............................................................................. 54
4.14 DDR VTP Enable Register (DDRVTPER)................................................................... 54
Appendix A Revision History ............................................................................................. 55
SPRU986B–November 2007
Table of Contents
3
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
1
Data Paths to DDR2 Memory Controller.................................................................................. 8
DDR2 Memory Controller Clock Block Diagram......................................................................... 9
DDR2 Memory Controller Signals........................................................................................ 11
Refresh Command ......................................................................................................... 13
DCAB Command ........................................................................................................... 14
DEAC Command ........................................................................................................... 15
ACTV Command ........................................................................................................... 16
DDR2 READ Command................................................................................................... 17
DDR2 WRT Command .................................................................................................... 18
DDR2 MRS and EMRS Command ...................................................................................... 19
Byte Alignment.............................................................................................................. 20
Logical Address-to-DDR2 SDRAM Address Map...................................................................... 24
DDR2 SDRAM Column, Row, and Bank Access ...................................................................... 25
DDR2 Memory Controller FIFO Block Diagram ........................................................................ 26
DDR2 Memory Controller Reset Block Diagram ....................................................................... 30
DDR2 Memory Controller Power Sleep Controller Diagram.......................................................... 34
Connecting DDR2 Memory Controller for 32-Bit Connection......................................................... 37
Connecting DDR2 Memory Controller for 16-Bit Connection......................................................... 37
SDRAM Status Register (SDRSTAT).................................................................................... 41
SDRAM Bank Configuration Register (SDBCR) ....................................................................... 42
SDRAM Refresh Control Register (SDRCR) ........................................................................... 44
SDRAM Timing Register (SDTIMR) ..................................................................................... 45
SDRAM Timing Register 2 (SDTIMR2).................................................................................. 46
Peripheral Bus Burst Priority Register (PBBPR) ....................................................................... 47
Interrupt Raw Register (IRR) ............................................................................................. 48
Interrupt Masked Register (IMR) ......................................................................................... 49
Interrupt Mask Set Register (IMSR) ..................................................................................... 50
Interrupt Mask Clear Register (IMCR)................................................................................... 51
DDR PHY Control Register (DDRPHYCR) ............................................................................. 52
VTP IO Control Register (VTPIOCR).................................................................................... 53
DDR VTP Register (DDRVTPR) ......................................................................................... 54
DDR VTP Enable Register (DDRVTPER) .............................................................................. 54
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
4
List of Figures
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
1
PLLC2 Configuration....................................................................................................... 10
DDR2 Memory Controller Signal Descriptions ......................................................................... 11
DDR2 SDRAM Commands ............................................................................................... 12
Truth Table for DDR2 SDRAM Commands ............................................................................ 12
Addressable Memory Ranges ............................................................................................ 20
16-Bit External Memory ................................................................................................... 21
32-Bit External Memory ................................................................................................... 21
Bank Configuration Register Fields for Address Mapping ............................................................ 22
Logical Address-to-DDR2 SDRAM Address Map for 32-Bit SDRAM ............................................... 23
Logical Address-to-DDR2 SDRAM Address Map for 16-bit SDRAM................................................ 23
DDR2 Memory Controller FIFO Description ............................................................................ 26
Refresh Urgency Levels................................................................................................... 29
Reset Sources .............................................................................................................. 30
DDR2 SDRAM Configuration by MRS Command ..................................................................... 32
DDR2 SDRAM Configuration by EMRS(1) Command ................................................................ 32
SDRAM Bank Configuration Register (SDBCR) Configuration ...................................................... 38
DDR2 Memory Refresh Specification ................................................................................... 38
SDRAM Refresh Control Register (SDRCR) Configuration .......................................................... 38
SDRAM Timing Register (SDTIMR) Configuration .................................................................... 39
SDRAM Timing Register 2 (SDTIMR2) Configuration................................................................. 39
DDR PHY Control Register (DDRPHYCR) Configuration ............................................................ 40
DDR2 Memory Controller Registers Relative to Base Address 2000 0000h....................................... 41
DDR2 Memory Controller Registers Relative to Base Address 01C4 2000h ...................................... 41
DDR2 Memory Controller Registers Relative to Base Address 01C4 0000h ...................................... 41
SDRAM Status Register (SDRSTAT) Field Descriptions ............................................................. 41
SDRAM Bank Configuration Register (SDBCR) Field Descriptions ................................................. 42
SDRAM Refresh Control Register (SDRCR) Field Descriptions..................................................... 44
SDRAM Timing Register (SDTIMR) Field Descriptions ............................................................... 45
SDRAM Timing Register 2 (SDTIMR2) Field Descriptions ........................................................... 46
Peripheral Bus Burst Priority Register (PBBPR) Field Descriptions................................................. 47
Interrupt Raw Register (IRR) Field Descriptions ....................................................................... 48
Interrupt Masked Register (IMR) Field Descriptions................................................................... 49
Interrupt Mask Set Register (IMSR) Field Descriptions ............................................................... 50
Interrupt Mask Clear Register (IMCR) Field Descriptions............................................................. 51
DDR PHY Control Register (DDRPHYCR) Field Descriptions ....................................................... 52
VTP IO Control Register (VTPIOCR) Field Descriptions.............................................................. 53
DDR VTP Register (DDRVTPR) Field Descriptions ................................................................... 54
DDR VTP Enable Register (DDRVTPER) Field Descriptions ........................................................ 54
Document Revision History ............................................................................................... 55
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
A-1
SPRU986B–November 2007
List of Tables
5
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
SPRU986B–November 2007
Read This First
About This Manual
This document describes the DDR2 memory controller in the TMS320DM643x Digital Media Processor
(DMP).
Notational Conventions
This document uses the following conventions.
•
Hexadecimal numbers are shown with the suffix h. For example, the following number is 40
hexadecimal (decimal 64): 40h.
•
Registers in this document are shown in figures and described in tables.
–
Each register figure shows a rectangle divided into fields that represent the fields of the register.
Each field is labeled with its bit name, its beginning and ending bit numbers above, and its
read/write properties below. A legend explains the notation used for the properties.
–
Reserved bits in a register figure designate a bit that is used for future device expansion.
Related Documentation From Texas Instruments
The following documents describe the TMS320DM643x Digital Media Processor (DMP). Copies of these
documents are available on the Internet at www.ti.com. Tip: Enter the literature number in the search box
The current documentation that describes the DM643x DMP, related peripherals, and other technical
SPRU978 — TMS320DM643x DMP DSP Subsystem Reference Guide. Describes the digital signal
processor (DSP) subsystem in the TMS320DM643x Digital Media Processor (DMP).
SPRU983 — TMS320DM643x DMP Peripherals Overview Reference Guide. Provides an overview and
briefly describes the peripherals available on the TMS320DM643x Digital Media Processor (DMP).
SPRAA84 — TMS320C64x to TMS320C64x+ CPU Migration Guide. Describes migrating from the
Texas Instruments TMS320C64x digital signal processor (DSP) to the TMS320C64x+ DSP. The
objective of this document is to indicate differences between the two cores. Functionality in the
devices that is identical is not included.
SPRU732 — TMS320C64x/C64x+ DSP CPU and Instruction Set Reference Guide. Describes the CPU
architecture, pipeline, instruction set, and interrupts for the TMS320C64x and TMS320C64x+ digital
signal processors (DSPs) of the TMS320C6000 DSP family. The C64x/C64x+ DSP generation
comprises fixed-point devices in the C6000 DSP platform. The C64x+ DSP is an enhancement of
the C64x DSP with added functionality and an expanded instruction set.
SPRU871 — TMS320C64x+ DSP Megamodule Reference Guide. Describes the TMS320C64x+ digital
signal processor (DSP) megamodule. Included is a discussion on the internal direct memory access
(IDMA) controller, the interrupt controller, the power-down controller, memory protection, bandwidth
management, and the memory and cache.
6
Preface
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Guide
SPRU986B–November 2007
DDR2 Memory Controller
1
Introduction
This document describes the DDR2 memory controller in the TMS320DM643x Digital Media Processor
(DMP).
1.1 Purpose of the Peripheral
The DDR2 memory controller is used to interface with JESD79D-2A standard compliant DDR2 SDRAM
devices. Memories types such as DDR1 SDRAM, SDR SDRAM, SBSRAM, and asynchronous memories
are not supported. The DDR2 memory controller is the major memory location for program and data
storage.
1.2 Features
The DDR2 memory controller supports the following features:
•
•
•
JESD79D-2A standard compliant DDR2 SDRAM
256 Mbyte memory space
Data bus width of 32 or 16 bits (see the device-specific data manual for the mode(s) that are
supported)
•
•
•
•
•
•
•
•
•
•
•
•
CAS latencies: 2, 3, 4, and 5
Internal banks: 1, 2, 4, and 8
Burst length: 8
Burst type: sequential
1 CS signal
Page sizes: 256, 512, 1024, and 2048
SDRAM autoinitialization
Self-refresh mode
Prioritized refresh
Programmable refresh rate and backlog counter
Programmable timing parameters
Little-endian operating mode
SPRU986B–November 2007
DDR2 Memory Controller
7
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1.3 Functional Block Diagram
general data paths to on-chip peripherals and external DDR2 SDRAM.
Master peripherals, EDMA, the ARM processor, and DSP can access the DDR2 memory controller
through the switched central resource (SCR).
Figure 1. Data Paths to DDR2 Memory Controller
DSP
Master
peripherals
DDR2
memory
controller
External
DDR2 SDRAM
SCR
BUS
BUS
EDMA
VPSS
1.4 Supported Use Case Statement
The DDR2 memory controller supports JESD79D-2A DDR2-400 SDRAM memories utilizing either 32-bit
1.5 Industry Standard(s) Compliance Statement
The DDR2 memory controller is compliant with the JESD79D-2A DDR2 SDRAM standard with the
exception of the following feature list:
•
On Die Termination (ODT). The DDR2 memory controller does not include any on-die terminating
resistors. Furthermore, the on-die terminating resistors of the DDR2 SDRAM device must be disabled
by tying the ODT input pin of the DDR2 SDRAM to ground.
•
Differential DQS. The DDR2 memory controller supports single ended DQS signals.
8
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2
Peripheral Architecture
This section describes the architecture of the DDR2 memory controller as well as how it is structured and
how it works within the context of the system-on-a-chip. The DDR2 memory controller can gluelessly
interface to most standard DDR2 SDRAM devices and supports such features as self-refresh mode and
prioritized refresh. In addition, it provides flexibility through programmable parameters such as the refresh
rate, CAS latency, and many SDRAM timing parameters. The following sections include details on how to
interface and properly configure the DDR2 memory controller to perform read and write operations to
the DDR2 memory controller to a common DDR2 SDRAM device.
2.1 Clock Control
The DDR2 memory controller receives two input clocks from internal clock sources, SYSCLK2 and
should be configured to clock at the frequency of the desired data rate, or stated similarly, it should
operate at twice the frequency of the desired DDR2 memory clock. DDR_CLK and DDR_CLK are the two
output clocks of the DDR2 memory controller providing the interface clock to the DDR2 SDRAM memory.
These two clocks operate at a frequency of PLL2_SYSCLK1/2.
2.1.1
Clock Source
from PLL controller 1 (PLLC1) and PLL2_SYSCLK1 is sourced from PLL controller 2 (PLLC2).
SYSCLK2 is clocked at a fixed divider ratio of PLL1. This divider is fixed at 3, meaning SYSCLK2 is
clocked at a frequency of PLL1/3. Once inside the DDR2 memory controller, this signal is called VCLK.
PLLC2 has a programmable divider that is used to divide-down the output clock of PLL2. This divider
should be configured such that PLLC2 supplies the PLL2_SYSCLK1 at the desired frequency. For
example, if a 150-MHZ DDR2 interface clock (DDR_CLK) is desired, then PLLC2 must be configured to
generate a 300-MHZ clock on PLL2_SYSCLK1. Once inside the DDR2 memory controller,
PLL2_SYSCLK1 is called X2_CLK.
Figure 2. DDR2 Memory Controller Clock Block Diagram
DDR_CLK
DDR_CLK
DDR2
memory
controller
VCLK
X2_CLK
PLL2_SYSCLK1
/2
PLLC2
SYSCLK2
/3
PLLC1
SPRU986B–November 2007
DDR2 Memory Controller
9
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.1.2
Clock Configuration
The frequency of PLL2_SYSCLK1 is configured by selecting the appropriate PLL multiplier and divider
ratio. The PLL multiplier and divider ratio are selected by programming registers within PLLC2. Table 1
shows a list of PLL multiplier and divider settings to achieve certain DDR2 frequencies. The data in
Table 1 is derived by assuming a 27-MHZ reference clock. See the device-specific data manual for the
clock frequencies that are supported. See the TMS320DM643x DMP DSP Subsystem Reference Guide
(SPRU978) for information on the PLL controller.
Note: PLLC2 should be configured and a stable clock present on PLL2_SYSCLK1 before releasing
the DDR2 memory controller from reset.
Table 1. PLLC2 Configuration
PLL Multiplier PLL Frequency (MHZ)
Divider Ratio
X2_CLK Frequency (MHZ)
DDR2 Clock Frequency (MHZ)
28
19
29
20
31
21
32
22
23
24
25
756
513
783
540
837
567
864
594
621
648
675
3
2
3
2
3
2
3
2
2
2
2
252
126
256.6
261
128.3
130.5
135
270
279
139.5
141.8
144
283.5
288
297
148.5
155.3
162
310
324
337.5
168.8
2.1.3
DDR2 Memory Controller Internal Clock Domains
There are two clock domains within the DDR2 memory controller. The two clock domains are driven by
VCLK and a divided-down by 2 version of X2_CLK called MCLK. The command FIFO, write FIFO, and
read FIFO described in Section 2.8 are all on the VCLK domain. From this, you can see that VCLK drives
the interface to the peripheral bus.
The MCLK domain consists of the DDR2 memory controller state machine and memory-mapped registers.
This clock domain is clocked at the rate of the external DDR2 memory, X2_CLK/2.
To conserve power within the DDR2 memory controller, VCLK, MCLK, and X2_CLK may be stopped. See
2.2 Memory Map
See the device-specific data manual for information describing the device memory-map.
10
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.3 Signal Descriptions
features are included:
•
•
•
•
•
The maximum data bus is 32-bits wide.
The address bus is 13-bits wide with an additional 3 bank address pins.
Two differential output clocks driven by internal clock sources.
Command signals: Row and column address strobe, write enable strobe, data strobe, and data mask.
One chip select signal and one clock enable signal.
Figure 3. DDR2 Memory Controller Signals
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_WE
DDR_RAS
DDR2
memory
controller
DDR_CAS
DDR_DQM[3:0]
DDR_DQS[3:0]
DDR_BA[2:0]
DDR_A[12:0]
DDR_D[31:0]
200 Ω
DDR_ZN
DDR_ZP
200 Ω
Table 2. DDR2 Memory Controller Signal Descriptions
Pin
Type
Description
DDR_CLK,
DDR_CLK
O/Z
Clock: Differential clock outputs.
DDR_CKE
O/Z
O/Z
O/Z
O/Z
O/Z
O/Z
I/O/Z
O/Z
O/Z
I/O/Z
O
Clock enable: Active high.
DDR_CS
Chip select: Active low.
DDR_WE
Write enable strobe: Active low, command output.
Row address strobe: Active low, command output.
Column address strobe: Active low, command output.
Data mask: Output mask signal for write data.
DDR_RAS
DDR_CAS
DDR_DQM[3:0]
DDR_DQS[3:0]
DDR_BA[2:0]
DDR_A[12:0]
DDR_D[31:0]
Data strobe: Active high, bi-directional signals. Output with write data, input with read data.
Bank address: Output, defining which bank a given command is applied.
Address: Address bus.
Data: Bi-directional data bus. Input for read data, output for write data.
DDR_ZN,
DDR_ZP
Output impedance control: Required to set the DDR2 output impedance. Connected by way of
4 times the desired impedance of the output buffer. By changing the size of the resistor, the
DDR2 outputs can be tuned to match the board load, if necessary.
SPRU986B–November 2007
DDR2 Memory Controller
11
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4 Protocol Description(s)
signal truth table for the DDR2 SDRAM commands.
Table 3. DDR2 SDRAM Commands
Command
ACTV
Function
Activates the selected bank and row.
DCAB
Precharge all command. Deactivates (precharges) all banks.
Precharge single command. Deactivates (precharges) a single bank.
Device Deselect.
DEAC
DESEL
EMRS
Extended Mode Register set. Allows altering the contents of the mode register.
Mode register set. Allows altering the contents of the mode register.
No operation.
MRS
NOP
Power Down
READ
Power down mode.
Inputs the starting column address and begins the read operation.
READ with
autoprecharge
Inputs the starting column address and begins the read operation. The read operation is followed by a
precharge.
REFR
Autorefresh cycle.
SLFREFR
WRT
Self-refresh mode.
Inputs the starting column address and begins the write operation.
WRT with
autoprecharge
Inputs the starting column address and begins the write operation. The write operation is followed by a
precharge.
Table 4. Truth Table for DDR2 SDRAM Commands
DDR2
SDRAM:
CKE
CS
RAS
CAS
WE
BA[2:0]
A[12:11, 9:0]
A10
DDR2
memory
controller:
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_BA[2:0]
DDR_A[12:11, 9:0]
DDR_A[10]
Previous
Cycles
Current Cycle
ACTV
DCAB
DEAC
MRS
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
L
H
H
H
L
H
L
Bank
X
Row Address
X
X
L
L
L
L
Bank
BA
L
L
OP Code
OP Code
EMRS
READ
L
L
L
BA
H
H
L
H
H
BA
Column Address
Column Address
L
READ with
precharge
L
BA
H
WRT
H
H
H
H
L
L
H
H
L
L
L
L
BA
BA
Column Address
Column Address
L
L
WRT with
precharge
REFR
H
H
H
L
L
L
L
L
L
L
H
H
X
X
X
X
X
X
SLFREFR
entry
SLFREFR
exit
L
H
H
L
X
H
H
X
X
H
X
H
X
H
H
X
X
H
X
H
X
H
H
X
X
H
X
H
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOP
H
H
H
X
X
L
L
DESEL
H
H
L
Power Down
entry
Power Down
exit
L
H
H
L
12
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.1
Refresh Mode
is automatically preceded by a DCAB command, ensuring the deactivation of all CE spaces and banks
selected. Following the DCAB command, the DDR2 memory controller begins performing refreshes at a
rate defined by the refresh rate (RR) bit in the SDRAM refresh control register (SDRCR). Page information
is always invalid before and after a REFR command; thus, a refresh cycle always forces a page miss. This
type of refresh cycle is often called autorefresh. Autorefresh commands may not be disabled within the
Figure 4. Refresh Command
RFR
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12:0]
DDR_BA[2:0]
DDR_DQM[3:0]
SPRU986B–November 2007
DDR2 Memory Controller
13
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.2
Deactivation (DCAB and DEAC)
The precharge all banks command (DCAB) is performed after a reset to the DDR2 memory controller or
following the initialization sequence. DDR2 SDRAMs also require this cycle prior to a refresh (REFR) and
mode set register commands (MRS and EMRS). During a DCAB command, DDR_A[10] is driven high to
Figure 5. DCAB Command
DCAB
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12,11, 9:0]
DDR_A[10]
DDR_BA[2:0]
DDR_DQM[3:0]
14
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
The DEAC command closes a single bank of memory specified by the bank select signals. Figure 6 shows
the timings diagram for a DEAC command.
Figure 6. DEAC Command
DEAC
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12,11, 9:0]
DDR_A[10]
DDR_BA[2:0]
DDR_DQM[3:0]
SPRU986B–November 2007
DDR2 Memory Controller
15
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.3
Activation (ACTV)
The DDR2 memory controller automatically issues the activate (ACTV) command before a read or write to
a closed row of memory. The ACTV command opens a row of memory, allowing future accesses (reads or
writes) with minimum latency. The value of DDR_BA[2:0] selects the bank and the value of A[12:0] selects
the row. When the DDR2 memory controller issues an ACTV command, a delay of tRCD is incurred before
the currently active row and bank of memory can achieve much higher throughput than reads or writes to
random areas because every time a new row is accessed, the ACTV command must be issued and a
delay of tRCD incurred.
Figure 7. ACTV Command
ACTV
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12:0]
DDR_BA[2:0]
ROW
BANK
DDR_DQM[3:0]
16
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.4
READ Command
command initiates a burst read operation to an active row. During the READ command, DDR_CAS drives
low, DDR_WE and DDR_RAS remain high, the column address is driven on DDR_A[12:0], and the bank
address is driven on DDR_BA[2:0].
The DDR2 memory controller uses a burst length of 8, and has a programmable CAS latency of 2, 3, 4, or
5. The CAS latency is three cycles in Figure 8. Read latency is equal to CAS latency plus additive latency.
The DDR2 memory controller always configures the memory to have an additive latency of 0, so read
latency equals CAS latency. Since the default burst size is 8, the DDR2 memory controller returns 8
pieces of data for every read command. If additional accesses are not pending to the DDR2 memory
controller, the read burst completes and the unneeded data is disregarded. If additional accesses are
pending, depending on the scheduling result, the DDR2 memory controller can terminate the read burst
and start a new read burst. Furthermore, the DDR2 memory controller does not issue a DAB/DEAC
command until page information becomes invalid.
Figure 8. DDR2 READ Command
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
COL
DDR_A[12:0]
DDR_BA[2:0]
DDR_A[10]
BANK
DDR_DQM[3:0]
CAS Latency
D0
D1
D2
D3
D4
D5
D6
D7
DDR_D[31:0]
DDR_DQS[3:0]
SPRU986B–November 2007
DDR2 Memory Controller
17
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.5
Write (WRT) Command
Prior to a WRT command, the desired bank and row are activated by the ACTV command. Following the
WRT command, a write latency is incurred. Write latency is equal to CAS latency minus 1. All writes have
a burst length of 8. The use of the DDR_DQM outputs allows byte and halfword writes to be executed.
If the transfer request is for less than 8 words, depending on the scheduling result and the pending
commands, the DDR2 memory controller can:
•
•
Mask out the additional data using DDR_DQM outputs
Terminate the write burst and start a new write burst
The DDR2 memory controller does not perform the DEAC command until page information becomes
invalid.
Figure 9. DDR2 WRT Command
DDR_CLK
DDR_CLK
Sample
Write Latency
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12:0]
COL
DDR_BA[2:0]
DDR_A[10]
BANK
DDR_DQM[3:0]
DDR_D[31:0]
DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM7 DQM8
D0
D1
D2
D3
D4
D5
D6
D7
DDR_DQS[3:0]
18
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.4.6
Mode Register Set (MRS and EMRS)
DDR2 SDRAM contains mode and extended mode registers that configure the DDR2 memory for
operation. These registers control burst type, burst length, CAS latency, DLL enable/disable (on DDR2
device), single-ended strobe, etc.
The DDR2 memory controller programs the mode and extended mode registers of the DDR2 memory by
issuing MRS and EMRS commands. When the MRS or EMRS command is executed, the value on
DDR_BA[1:0] selects the mode register to be written and the data on DDR_A[12:0] is loaded into the
The DDR2 memory controller only issues MRS and EMRS commands during the DDR2 memory controller
Figure 10. DDR2 MRS and EMRS Command
MRS/EMRS
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_RAS
DDR_CAS
DDR_WE
DDR_A[12:0]
DDR_BA[2:0]
COL
BANK
SPRU986B–November 2007
DDR2 Memory Controller
19
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.5 Memory Width and Byte Alignment
addressable memory ranges on the DDR2 memory controller. See the device-specific data manual for the
memory widths that are supported.
right-aligned on the data bus.
Table 5. Addressable Memory Ranges
Memory Width
Maximum addressable bytes per CS space
Description
×16
128 Mbytes
256 Mbytes
Halfword address
Word address
×32
Figure 11. Byte Alignment
DDR2 memory controller data bus
DDR_D[31:24]
DDR_D[23:16]
DDR_D[15:8]
DDR_D[7:0]
32-bit memory device
16-bit memory device
20
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.6 Endianness Considerations
The DDR2 memory controller supports little-endian operating mode. This determines the order in which
data on the internal data bus is written to or read from devices that are not as wide as the internal data
bus. However, the DDR2 memory controller maintains the natural order of endian operations. That is, a
stream of data starting at any address N will always be accessed in the correct or incrementing data
order. The DDR2 memory controller will always access address N prior to N + 1 in any data width. Table 6
and Table 7 show operation of the DDR2 memory controller for both 16-bit and 32-bit external memory.
See the device-specific data manual for the memory widths that are supported.
Table 6. 16-Bit External Memory
Internal Data (64-Bit
DDR_A[2:1]
DDR_D[15:0]
CDEFh
89ABh
0123 4567 89AB CDEFh
0123 4567 89AB CDEFh
0123 4567 89AB CDEFh
0123 4567 89AB CDEFh
00
01
10
11
4567h
0123h
Table 7. 32-Bit External Memory
Internal Data (64-Bit)
0123 4567 89AB CDEFh
0123 4567 89AB CDEFh
DDR_A[2]
DDR_D[31:0]
89AB CDEFh
0123 4567h
0
1
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.7 Address Mapping
The DDR2 memory controller views external DDR2 SDRAM as one continuous block of memory. This
statement is true regardless of the number of external physical devices mapped to a given chip select
space. The DDR2 memory controller receives DDR2 memory access requests along with a 32-bit logical
address from the rest of the system. In turn, the DDR2 memory controller uses the logical address to
generate a row/page, column, and bank address for the DDR2 SDRAM. The number of column and bank
address bits used is determined by the IBANK and PAGESIZE fields in the SDRAM bank configuration
Table 8. Bank Configuration Register Fields for Address Mapping
Bit Field
Bit Value
Bit Description
IBANK
Defines the number of internal banks on the external DDR2 memory.
0
1 bank
1h
2h
3h
2 banks
4 banks
8 banks
PAGESIZE
Defines the page size of each page of the external DDR2 memory.
256 words (requires 8 column address bits)
512 words (requires 9 column address bits)
1024 words (requires 10 column address bits)
2048 words (requires 11 column address bits)
0
1h
2h
3h
source address of the DDR2 memory controller to the DDR2 SDRAM row, column, and bank address bits.
The DDR2 memory controller logical address always contains 13 row address bits, whereas the number of
how the logical address bits map to the DDR2 SDRAM row, column, and bank bits for combinations of
IBANK and PAGESIZE values. The same DDR2 memory controller pins provide the row and column
address to the DDR2 SDRAM, thus the DDR2 memory controller appropriately shifts the address during
row and column address selection.
banks into the device memory map. Note that during a linear access, the DDR2 memory controller
increments the column address as the logical address increments. When the DDR2 memory controller
reaches a page/row boundary, it moves onto the same page/row in the next bank. This movement
continues until the same page has been accessed in all banks. To the DDR2 SDRAM, this process looks
By traversing across banks while remaining on the same row/page, the DDR2 memory controller
maximizes the number of activated banks for a linear access. This results in the maximum number of
open pages when performing a linear access being equal to the number of banks. Note that the DDR2
memory controller never opens more than one page per bank.
Ending the current access is not a condition that forces the active DDR2 SDRAM row to be closed. The
DDR2 memory controller leaves the active row open until it becomes necessary to close it. This decreases
the deactivate-reactivate overhead.
22
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
Table 9. Logical Address-to-DDR2 SDRAM Address Map for 32-Bit SDRAM
SDBCR Bit
Logical Address(1)
IBANK
0
PAGESIZE
31
30
29
28
27
26
25
24
23
22:16
15
14
13
12
11
10
9:2
1:0
0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
nrb=13
ncb=8
1
nrb=13
nbb=1 ncb=8
ncb=8
2h
3h
0
0
nrb=13
nrb=13
nrb=13
nbb=2
0
nrb=13
nrb=13
nrb=13
nrb=13
nbb=3
nbb=2
ncb=8
1
nrb=13
ncb=9
1
1
nbb=1 ncb=9
ncb=9
2h
3h
0
1
1
nrb=13
nrb=13
nrb=13
nbb=3
nbb=2
nbb=1
ncb=9
2h
2h
2h
2h
3h
3h
3h
3h
ncb=10
1
nbb=1 ncb=10
ncb=10
2h
3h
0
nrb=13
nrb=13
nbb=3
nbb=2
ncb=10
ncb=11
1
ncb=11
2h
3h
ncb=11
nrb=13
nbb=3
ncb=11
(1)
Legend: ncb = number of column address bits; nrb = number of row address bits; nbb = number of bank address bits.
Table 10. Logical Address-to-DDR2 SDRAM Address Map for 16-bit SDRAM
SDBCR Bit
Logical Address(1)
IBANK
PAGESIZE
31
30
29
28
27
26
25
24
23
22
21:15
14
13
12
11
10
9
8:1
0
0
1
0
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
nrb=13
ncb=8
nrb=13
nbb=1 ncb=8
ncb=8
2h
3h
0
0
nrb=13
nrb=13
nrb=13
nbb=2
0
nrb=13
nrb=13
nrb=13
nrb=13
nbb=3
nbb=2
ncb=8
1
nrb=13
ncb=9
1
1
nbb=1 ncb=9
ncb=9
2h
3h
0
1
1
nrb=13
nrb=13
nrb=13
nbb=3
nbb=2
ncb=9
2h
2h
2h
2h
3h
3h
3h
3h
ncb=10
1
nbb=1 ncb=10
ncb=10
2h
3h
0
nrb=13
nrb=13
nbb=3
nbb=2
ncb=10
ncb=11
1
nbb=1 ncb=11
ncb=11
2h
3h
nrb=13
nbb=3
ncb=11
(1)
Legend: ncb = number of column address bits; nrb = number of row address bits; nbb = number of bank address bits.
SPRU986B–November 2007
DDR2 Memory Controller
23
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
Figure 12. Logical Address-to-DDR2 SDRAM Address Map
Col. 0
Col. 1
Col. 2
Col. 3
Col. 4
Col. M−1
Col. M
Row 0, bank 0
Row 0, bank 1
Row 0, bank 2
Row 0, bank P
Row 1, bank 0
Row 1, bank 1
Row 1, bank 2
Row 1, bank P
Row N, bank 0
Row N, bank 1
Row N, bank 2
Row N, bank P
NOTE: M is number of columns (as determined by PAGESIZE) minus 1, P is number of banks (as determined by
IBANK) minus 1, and N is number of rows (as determined by both PAGESIZE and IBANK) minus 1.
24
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
Figure 13. DDR2 SDRAM Column, Row, and Bank Access
C
o
l
C
o
l
C
o
l
C
o
l
C
o
l
C
o
l
C
o
l
C
o
l
Bank 0
Row 0
Row 1
Row 2
0
1
2
3
M
C
o
l
C
o
l
C
o
l
C
o
l
Bank 1
Row 0
Row 1
Row 2
0
1
2
3
M
C
o
l
C
o
l
C
o
l
C
o
l
Bank 2
Row 0
Row 1
Row 2
0
1
2
3
M
Bank P
Row 0
Row 1
Row 2
0
1
2
3
M
Row N
Row N
Row N
Row N
NOTE: M is number of columns (as determined by PAGESIZE) minus 1, P is number of banks (as determined by
IBANK) minus 1, and N is number of rows (as determined by both PAGESIZE and IBANK) minus 1.
SPRU986B–November 2007
DDR2 Memory Controller
25
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.8 DDR2 Memory Controller Interface
To move data efficiently from on-chip resources to external DDR2 SDRAM memory, the DDR2 memory
controller makes use of a command FIFO, a write FIFO, a read FIFO, and command and data schedulers.
read data arrive at the DDR2 memory controller parallel to each other. The same peripheral bus is used to
write and read data from external memory as well as internal memory-mapped registers.
Table 11. DDR2 Memory Controller FIFO Description
FIFO
Description
Depth (64-bit doublewords)
Command
Write
Stores all commands coming from on-chip requestors
Stores write data coming from on-chip requestors to memory
Stores read data coming from memory to on-chip requestors
7
11
17
Read
Figure 14. DDR2 Memory Controller FIFO Block Diagram
Command/Data
Scheduler
Command
to Memory
Command FIFO
Write FIFO
Write Data
to Memory
Read FIFO
Read Data
from
Memory
Registers
Command
Data
26
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.8.1
Command Ordering and Scheduling, Advanced Concept
The DDR2 memory controller performs command re-ordering and scheduling in an attempt to achieve
efficient transfers with maximum throughput. The goal is to maximize the utilization of the data, address,
and command buses while hiding the overhead of opening and closing DDR2 SDRAM rows. Command
re-ordering takes place within the command FIFO.
Typically, a given master issues commands on a single priority. EDMA transfer controller read and write
ports are different masters. The DDR2 memory controller first reorders commands from each master
based on the following rules:
•
•
Selects the oldest command (first command in the queue)
Selects a read before a write if:
–
–
The read is to a different block address (2048 bytes) than the write
The read has greater or equal priority
The second bullet above may be viewed as an exception to the first bullet. This means that for an
individual master, all of its commands will complete from oldest to newest, with the exception that a read
may be advanced ahead of an older, lower or equal priority write. Following this scheduling, each master
may have one command ready for execution.
Next, the DDR2 memory controller examines each of the commands selected by the individual masters
and performs the following reordering:
•
Among all pending reads, selects reads to rows already open. Among all pending writes, selects writes
to rows already open.
•
Selects the highest priority command from pending reads and writes to open rows. If multiple
commands have the highest priority, then the DDR2 memory controller selects the oldest command.
The DDR2 memory controller may now have a final read and write command. If the Read FIFO is not full,
then the read command will be performed before the write command, otherwise the write command will be
performed first.
Besides commands received from on-chip resources, the DDR2 memory controller also issues refresh
commands. The DDR2 memory controller attempts to delay refresh commands as long as possible to
maximize performance while meeting the SDRAM refresh requirements. As the DDR2 memory controller
issues read, write, and refresh commands to DDR2 SDRAM memory, it adheres to the following rules:
1. Refresh request resulting from the Refresh Must level of urgency being reached
2. Read request without a higher priority write (selected from above reordering algorithm)
3. Refresh request resulting from the Refresh Need level of urgency being reached
4. Write request (selected from above reordering algorithm)
5. Refresh request resulting from Refresh May level of urgency being reached
6. Request to enter self-refresh mode
The following results from the above scheduling algorithm:
•
•
•
All writes from a single master will complete in order
All reads from a single master will complete in order
From the same master, any read to the same location (or within 2048 bytes) as a previous write will
complete in order
SPRU986B–November 2007
DDR2 Memory Controller
27
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.8.2
Command Starvation
The reordering and scheduling rules listed above may lead to command starvation, which is the
prevention of certain commands from being processed by the DDR2 memory controller. Command
starvation results from the following conditions:
•
•
A continuous stream of high-priority read commands can block a low-priority write command
A continuous stream of DDR2 SDRAM commands to a row in an open bank can block commands to
the closed row in the same bank.
To avoid these conditions, the DDR2 memory controller can momentarily raise the priority of the oldest
command in the command FIFO after a set number of transfers have been made. The PR_OLD_COUNT
bit field in the peripheral bus burst priority register (PBBPR) sets the number of the transfers that must be
made before the DDR2 memory controller will raise the priority of the oldest command.
Note: Leaving the PR_OLD_COUNT bits at their default value (FFh) disables this feature of the
EMIF. This means commands can stay in the command FIFO indefinitely. Therefore, these
bits should be set to FEh immediately following reset to enable this feature with the highest
level of allowable memory transfers. It is suggested that system level prioritization be set to
avoid placing high-bandwidth masters on the highest priority levels. These bits can be left as
FEh unless advanced bandwidth/prioritization control is required.
2.8.3
Possible Race Condition
A race condition may exist when certain masters write data to the DDR2 memory controller. For example,
if master A passes a software message via a buffer in DDR2 memory and does not wait for indication that
the write completes, when master B attempts to read the software message it may read stale data and
therefore receive an incorrect message. In order to confirm that a write from master A has landed before a
read from master B is performed, master A must wait for the write completion status from the DDR2
memory controller before indicating to master B that the data is ready to be read. If master A does not
wait for indication that a write is complete, it must perform the following workaround:
1. Perform the required write.
2. Perform a dummy write to the DDR2 memory controller SDRAM Status register.
3. Perform a dummy read to the DDR2 memory controller SDRAM Status register.
4. Indicate to master B that the data is ready to be read after completion of the read in step 3. The
completion of the read in step 3 ensures that the previous write was done.
The EDMA and ATA peripherals do not need to implement the above workaround. If a peripheral is not
listed here, then the above workaround is required. Refer to the device-specific data manual for more
information.
28
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.9 Refresh Scheduling
The DDR2 memory controller issues autorefresh (REFR) commands to DDR2 SDRAM devices at a rate
defined in the refresh rate (RR) bit field in the SDRAM refresh control register (SDRCR). A refresh interval
counter is loaded with the value of the RR bit field and decrements by 1 each cycle until it reaches zero.
Once the interval counter reaches zero, it reloads with the value of the RR bit. Each time the interval
counter expires, a refresh backlog counter increments by 1. Conversely, each time the DDR2 memory
controller performs a REFR command, the backlog counter decrements by 1. This means the refresh
backlog counter records the number of REFR commands the DDR2 memory controller currently has
outstanding.
The DDR2 memory controller issues REFR commands based on the level of urgency. The level of
controller issues a REFR command before servicing any new memory access requests. Following a REFR
command, the DDR2 memory controller waits T_RFC cycles, defined in the SDRAM timing register
(SDTIMR), before rechecking the refresh urgency level.
In addition to the refresh counter previously mentioned, a separate backlog counter ensures the interval
between two REFR commands does not exceed 8× the refresh rate. This backlog counter increments by 1
each time the interval counter expires and resets to zero when the DDR2 memory controller issues a
REFR command. When this backlog counter is greater than 7, the DDR2 memory controller issues four
REFR commands before servicing any new memory requests.
The refresh counters do not operate when the DDR2 memory is in self-refresh mode.
Table 12. Refresh Urgency Levels
Urgency Level
Description
Refresh May
Backlog count is greater than 0. Indicates there is a backlog of REFR commands, when the DDR2 memory
controller is not busy it will issue the REFR command.
Refresh Release
Refresh Need
Refresh Must
Backlog count is greater than 3. Indicates the level at which enough REFR commands have been performed
and the DDR2 memory controller may service new memory access requests.
Backlog count is greater than 7. Indicates the DDR2 memory controller should raise the priority level of a
REFR command above servicing a new memory access.
Backlog count is greater than 11. Indicates the level at which the DDR2 memory controller should perform a
REFR command before servicing new memory access requests.
2.10 Self-Refresh Mode
Setting the self refresh (SR) bit in the SDRAM refresh control register (SDRCR) to 1 forces the DDR2
memory controller to place the external DDR2 SDRAM in a low-power mode (self refresh), in which the
DDR2 SDRAM maintains valid data while consuming a minimal amount of power. When the SR bit is
asserted, the DDR2 memory controller continues normal operation until all outstanding memory access
requests have been serviced and the refresh backlog has been cleared. At this point, all open pages of
DDR2 SDRAM are closed and a self-refresh (SLFRFR) command (an autorefresh command with
DDR_CKE low) is issued.
The DDR2 memory controller exits the self-refresh state when a memory access is received or when the
SR bit in SDRCR is cleared to 0. While in the self-refresh state, if a request for a memory access is
received, the DDR2 memory controller services the memory access request, returning to the self-refresh
state upon completion. The DDR2 memory controller will not wake up from the self-refresh state (whether
from a memory access request or from clearing the SR bit) until T_CKE + 1 cycles have expired since the
self-refresh command was issued. The value of T_CKE is defined in the SDRAM timing 2 register
(SDTIMR2).
After exiting from the self-refresh state, the DDR2 memory controller will not immediately start executing
commands. Instead, it will wait T_SXNR + 1 clock cycles before issuing non-read commands and
T_SXRD + 1 clock cycles before issuing read commands. The SDRAM timing 2 register (SDTIM2)
programs the values of T_SXNR and T_SXRD.
SPRU986B–November 2007
DDR2 Memory Controller
29
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
Once in self-refresh mode, the DDR2 memory controller input clocks (VCLK and X2_CLK) may be gated
off or changed in frequency. Stable clocks must be present before exiting self-refresh mode. See
memory controller input clocks.
2.11 Reset Considerations
The DDR2 memory controller has two reset signals, VRST and VCTL_RST. The VRST is a module-level
reset that resets both the state machine as well as the DDR2 memory controller memory-mapped
registers. The VCTL_RST resets the state machine only. If the DDR2 memory controller is reset
independently of other peripherals, the user's software should not perform memory, as well as register
accesses, while VRST or VCTL_RST are asserted. If memory or register accesses are performed while
the DDR2 memory controller is in the reset state, other masters may hang. Following the rising edge of
VRST or VCTL_RST, the DDR2 memory controller immediately begins its initialization sequence.
Command and data stored in the DDR2 memory controller FIFOs are lost. Table 13 describes the different
methods for asserting each reset signal. The Power and Sleep Controller (PSC) acts as a master
controller for power management for all of the peripherals on the device. For detailed information on
power management procedures using the PSC, see the TMS320DM643x DMP DSP Subsystem
Table 13. Reset Sources
Reset Signal
VRST
Reset Source
Hardware/device reset
Power and sleep controller
VCTL_RST
Figure 15. DDR2 Memory Controller Reset Block Diagram
DDR2
memory
controller
registers
Hard
Reset from
VRST
PLLC1
State
machine
VCTL_RST
DDR
PSC
30
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.12 VTP IO Buffer Calibration
The DDR2 memory controller is able to control the impedance of the output IO. This feature allows the
DDR2 memory controller to tune the output impedance of the IO to match that of the PCB board. Control
of the output impedance of the IO is an important feature because impedance matching reduces
reflections, creating a cleaner board design. Calibrating the output impedance of the IO will also reduce
the power consumption of the DDR2 memory controller. The calibration is performed with respect to
voltage, temperature, and process (VTP). The VTP information obtained from the calibration is used to
control the output impedance of the IO.
The impedance of the output IO is selected by the value of resistors connected to the DDR_ZN and
DDR_ZP pins. The resistor should be chosen to be 4 times the desired impedance of the output IO. The
DDR2 reference design requires the resistor values to be 200 ohms. This means that both the DDR_ZN
connection of the DDR_ZN and DDR_ZP pins.
To set the output impedance of the IO, calibration must be initiated by writing to the following
memory-mapped registers:
•
•
•
VTP IO Control Register (VTPIOCR)
DDR VTP Register (DDRVTPR)
DDR VTP Enable Register (DDRVTPER)
The VTP IO control register is written to begin the calibration. Once the calibration is complete, the VTP
information is stored in the DDR VTP register. The DDR VTP register should then be read, retrieving the
VTP information, and the VTP information written to the VTP IO control register. The DDR VTP enable
register is written to enable/disable access to the DDR VTP register. Steps 8-15 of the initialization
calibration.
Note: VTP IO calibration must be performed following device power up and device reset. If the
DDR2 memory controller is reset via the Power and Sleep Controller (PSC) and the VTP
input clock is disabled, accesses to the DDR2 memory controller will not complete. To
re-enable accesses to the DDR2 memory controller, enable the VTP input clock and then
perform the VTP calibration sequence again.
2.13 Auto-Initialization Sequence
The DDR2 SDRAM contains mode and extended mode registers that configure the DDR2 memory for
operation. These registers control burst type, burst length, CAS latency, DLL enable/disable (on the DDR2
device), single-ended strobe, etc. The DDR2 memory controller programs the mode and extended mode
registers of the DDR2 memory by issuing MRS and EMRS commands during the initialization sequence.
The initialization sequence performed by the DDR2 memory controller is compliant with the JESDEC79-2A
specification. The DDR2 memory controller performs an initialization sequence under the following
conditions:
•
•
Following reset (rising edge of VRST or VCTL_RST)
Following a write to the DDRDRIVE bit field or the two least-significant bytes in the SDRAM bank
configuration register (SDBCR)
During the initialization sequence, the DDR2 memory controller issues MRS and EMRS commands that
configure the DDR2 SDRAM mode register and extended mode register 1 with the values described in
of 0h. At the end of the initialization sequence, the DDR2 memory controller performs an autorefresh
cycle, leaving the DDR2 memory controller in an idle state with all banks deactivated.
When a reset occurs, the DDR2 memory controller immediately begins the initialization sequence. Under
this condition, commands and data stored in the DDR2 memory controller FIFOs will be lost. However,
when the initialization sequence is initiated by a write to the two least-significant bytes in SDBCR, data
and commands stored in the DDR2 memory controller FIFOs will not be lost and the DDR2 memory
controller will ensure read and write commands are completed before starting the initialization sequence.
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
Table 14. DDR2 SDRAM Configuration by MRS Command
DDR2 Memory
Controller
DDR2 SDRAM
Address Bus
Value
0
Register Bit
DDR2 SDRAM Field
Power Down Exit
Write Recovery
Function Selection
DDR_A[12]
12
Fast exit
DDR_A[11:9]
t_WR
11:9
Write recovery from autoprecharge. Value of 2,
3, 4, 5, or 6 is programmed based on value of
the T_WR bit in the SDRAM timing register
(SDTIMR).
DDR_A[8]
DDR_A[7]
DDR_A[6:4]
0
8
DLL Reset
Out of reset
0
7
Mode: Test or Normal
CAS Latency
Normal mode
CL bit
6:4
Value of 2, 3, 4, or 5 is programmed based on
value of the CL bit in the SDRAM bank
configuration register (SDBCR).
DDR_A[3]
0
3
Burst Type
Sequential
8
DDR_A[2:0]
3h
2:0
Burst Length
Table 15. DDR2 SDRAM Configuration by EMRS(1) Command
DDR2 Memory
Controller
DDR2 SDRAM
Address Bus
Value
Register Bit
DDR2 SDRAM Field
Output Buffer Enable
RDQS Enable
Function Selection
Output buffer enable
RDQS disable
DDR_A[12]
DDR_A[11]
DDR_A[10]
DDR_A[9:7]
DDR_A[6]
0
0
1
0
0
12
11
10
9:7
6
DQS enable
Disables differential DQS signaling.
Exit OCD calibration
OCD Calibration Program
ODT Value (Rtt)
Cleared to 0 to select 75 ohms. This feature is
not supported because the DDR_ODT signal is
not pinned out.
DDR_A[5:3]
DDR_A[2]
0
1
5:3
2
Additive Latency
ODT Value (Rtt)
0 cycles of additive latency
Set to 1 to select 75 ohms. This feature is not
supported because the DDR_ODT signal is not
pinned out.
DDR_A[1]
DDR_A[0]
1
0
1
0
Output Driver Impedance
DLL enable
DDR2 drive strength programmed to weak
(60%).
DLL enable
2.13.1 Initializing Configuration Registers
Perform the following steps when configuring the DDR2 memory controller memory-mapped registers:
1. Program the DDR PHY control register (DDRPHYCR) by setting the read latency (READLAT) bits to
the desired value as well as clearing the DLLPWRDN bit to 0.
2. Program the SDRAM bank configuration register (SDBCR) to the desired value with the TIMUNLOCK
bit set to 1 (unlocked).
3. Program the SDRAM timing register (SDTIMR) and SDRAM timing register 2 (SDTIMR2) to the
desired values to meet the DDR2 SDRAM memory data sheet specification.
4. Program SDBCR to the desired value with the TIMUNLOCK bit cleared to 0 (locked).
5. Program the RR bit in the SDRAM refresh control register (SDRCR) to the desired value to meet the
refresh requirements of the DDR2 SDRAM memory.
32
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.13.2 Initializing Following Device Power Up and Device RESET
CAUTION
The following power-up sequence is preliminary and is documented to
reflect the intended-use case. This power-up sequence may change at a
future date.
Following device power up, the DDR2 memory controller is held in reset with the internal clocks to the
module gated off. Before releasing the DDR2 memory controller from reset, the clocks to the module must
be turned on. Perform the following steps when turning the clocks on and initializing the module:
1. Program PLLC2 registers to provide a stable clock on PLL2_SYSCLK1 at the desired frequency.
2. Program the DDR2 memory controller Power and Sleep Controller (PSC) to enable VCLK.
3. Follow the register initialization procedure described in Section 2.13.1 to complete the DDR2 memory
controller configuration.
4. Perform a dummy read of DDR2 memory to verify initialization sequence has completed.
5. Perform a soft reset of the DDR2 memory controller via the PSC using the following procedure. See
the TMS320DM643x DMP DSP Subsystem Reference Guide (SPRU978) for details on how to
program the PSC.
a. To put the DDR2 memory controller into soft reset, program the PSC to place the DDR2 memory
controller into the SyncReset state.
b. To take the DDR2 memory controller out of soft reset, program the PSC to place the DDR2
memory controller into the Enable state.
6. Enable VTP manual calibration by writing to the VTP IO control register (VTPIOCR). See Section 4.12
for details on VTPIOCR.
a. With a single write, set the EN bit field (bit 13) to 1 and the RECAL bit field (bit 15) to 0 by writing a
value of 0000 201Fh.
b. Set the RECAL bit field (bit 15) to 1, making sure the value written to the EN field is still 1 by writing
a value of 0000 A01Fh. This begins the calibration sequence.
7. Wait for a minimum of 33 VTP clk cycles for calibration to complete. The VTP clock operates at
13.5 MHZ.
8. Enable access to the DDR VTP register by writing a 1 to the DDR VTP enable register.
DDR VTP register.
10. Write the VTP information to the PCH and NCH fields in the VTPIOCR. Make sure the RECAL and EN
bits remain set to 1.
11. Write 0 to EN bit field in the VTP control register to disable VTP calibration.
12. Disable access to the DDR VTP register by writing a 0 to the DDR VTP enable register.
13. Disable VTP input clock by disabling the bypass clock of PLL2.
Note: If the DDR2 memory controller is reset via the Power and Sleep Controller (PSC) and the
VTP input clock is disabled, accesses to the DDR2 memory controller will not complete. To
re-enable accesses to the DDR2 memory controller, enable the VTP input clock and then
perform the VTP calibration sequence again.
SPRU986B–November 2007
DDR2 Memory Controller
33
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.14 Interrupt Support
The DDR2 memory controller supports two addressing modes, linear incrementing and cache line wrap.
Upon receipt of an access request for an unsupported addressing mode, the DDR2 memory controller
generates an interrupt by setting the LT bit in the interrupt raw register (IRR). The DDR2 memory
controller will then treat the request as a linear incrementing request.
This interrupt is called the line trap interrupt and is the only interrupt the DDR2 memory controller
supports. It is an active-high interrupt and is enabled by the LTMSET bit in the interrupt mask set register
(IMSR). This interrupt is mapped to both the DSP and the ARM and is not multiplexed with other
interrupts.
2.15 DMA Event Support
The DDR2 memory controller is a DMA slave peripheral and therefore does not generate DMA events.
Data read and write requests may be made directly by masters and by the DMA.
2.16 Power Management
Power dissipation from the DDR2 memory controller may be managed by two methods:
•
•
Gating input clocks to the module off
Gating input clocks off to the DDR2 memory controller achieves higher power savings when compared to
the power savings of self-refresh mode. The input clocks are turned off outside of the DDR2 memory
controller through the use of the Power and Sleep Controller (PSC) and the PLL controller 2 (PLLC2).
information on power management procedures using the PSC, see the TMS320DM643x DMP DSP
Subsystem Reference Guide (SPRU978).
Before gating clocks off, the DDR2 memory controller must place the DDR2 SDRAM memory in
self-refresh mode by setting the SR bit in the SDRAM refresh control register (SDRCR) to 1. If the external
memory requires a continuous clock, the DDR2 memory controller clock provided by PLLC2 must not be
turned off because this may result in data corruption. See the following subsections for the proper
procedures to follow when stopping the DDR2 memory controller clocks. Once the clocks are stopped, to
re-enable the clocks follow the clock stop procedure in each respective subsection in reverse order.
Figure 16. DDR2 Memory Controller Power Sleep Controller Diagram
VCLKSTOP_REQ
VCLKSTOP_ACK
CLKSTOP_REQ
CLKSTOP_ACK
DDR
PSC
DDR2
memory
controller
SYSCLK2
MODCLK
VCLK
MODRST
LRST
VRST
VCTL_RST
X2_CLK
PLLC2
/2
PLL2_SYSCLK1
34
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Peripheral Architecture
2.16.1 DDR2 Memory Controller Clock Stop Procedure
CAUTION
The following clock stop procedures are preliminary and are documented
to reflect the intended-use cases. These clock stop procedures may
change at a future date.
Note: If an access occurs to the DDR2 memory controller after completing steps 1-5, the DLL will
wake up and lock, then the MCLK will turn on and the access will be performed. Following
step 6, all DDR2 accesses are disabled until the DDR2 memory controller is enabled again
through the LPSC.
To achieve maximum power savings VCLK, MCLK, X2_CLK, DDR_CLK, and DDR_CLK should be gated
off, as well as the DDR2 memory controller DLL powered down. Perform the following procedure when
shutting down clocks to achieve maximum power savings:
1. Allow software to complete the desired DDR2 transfers.
2. Set the SR bit in the DDR2 SDRAM refresh control register (SDRCR). The DDR2 memory controller
will complete any outstanding accesses and backlogged refresh cycles and then place the external
DDR2 memory in self-refresh mode.
3. Set the MCLKSTOPEN bit in SDRCR. This enables the DDR2 memory controller to shut off the MCLK.
4. Set the DLLPWRDN bit in the DDR PHY control register (DDRPHYCR) to 1 to power down the DDR2
memory controller DLL.
5. Poll the PHYRDY bit in the SDRAM status register (SDRSTAT) to be a logic-low indicating that the
MCLK has been stopped and the DLL is powered down.
6. Program DDR2 memory controller LPSC to disable VCLK.
7. Program PLLC2 registers to stop PLL2_SYSCLK1 which disables X2_CLK of the DDR2 memory
controller, as well as DDR_CLK and DDR_CLK.
To turn clocks back on:
1. Program PLLC2 registers to start PLL2_SYSCLK1 which sources X2_CLK of the DDR2 memory
controller.
2. Once PLL2_SYSCLK1 is stable, program the DDR2 memory controller LPSC to enable VCLK.
3. Clear the MCLKSTOPEN bit in the DDR2 SDRAM refresh control register (SDRCR) to 0.
4. Clear the DLLPWRDN bit in the DDR PHY control register (DDRPHYCR) to 0 to power up the DDR2
memory controller DLL.
5. Perform a soft reset of the DDR2 memory controller via the PSC using the following procedure. See
the TMS320DM643x DMP DSP Subsystem Reference Guide (SPRU978) for details on how to
program the PSC.
a. To put the DDR2 memory controller into soft reset, program the PSC to place the DDR2 memory
controller into the SyncReset state.
b. To take the DDR2 memory controller out of soft reset, program the PSC to place the DDR2
memory controller into the Enable state.
6. Clear the SR bit in SDRCR to 0.
2.17 Emulation Considerations
The DDR2 memory controller will remain fully functional during emulation halts to allow emulation access
to external memory.
SPRU986B–November 2007
DDR2 Memory Controller
35
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Use Cases
3
Supported Use Cases
The DDR2 memory controller allows a high degree of programmability for shaping DDR2 accesses. The
programmability inherent to the DDR2 memory controller provides the DDR2 memory controller with the
flexibility to interface with a variety of DDR2 devices. By programming the SDRAM bank configuration
register (SDBCR), SDRAM refresh control register (SDRCR), SDRAM timing register (SDTIMR), and
SDRAM timing register 2 (SDTIMR2), the DDR2 memory controller can be configured to meet the data
sheet specification for JESD79D-2A compliant DDR2 SDRAM.
This section presents an example describing how to interface the DDR2 memory controller to a JESD79D
DDR2-400 1-Gb device. The DDR2 memory controller is assumed to be operating at 133 MHZ.
3.1 Connecting the DDR2 Memory Controller to DDR2 Memory
displays a 32-bit interface; therefore, two 16-bit DDR2 devices are connected to the DDR2 memory
signals are point-to-point where as all other address, control, and clocks are not. Figure 18 displays a
16-bit interface; therefore, all signals are point-to-point. See the device-specific data manual for the data
bus widths that are supported.
3.2 Configuring Memory-Mapped Registers to Meet DDR2-400 Specification
As previously stated, four memory-mapped registers must be programmed to configure the DDR2 memory
controller to meet the data sheet specification of the attached DDR2 device. The registers are:
•
•
•
•
SDRAM bank configuration register (SDBCR)
SDRAM refresh control register (SDRCR)
SDRAM timing register (SDTIMR)
SDRAM timing register 2 (SDTIMR2)
In addition to these registers, the DDR PHY control register (DDRPHYCR) must also be programmed. The
configuration of DDRPHYCR is not dependent on the DDR2 device specification but rather on the board
layout.
information on the DDR2 memory controller registers.
36
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Use Cases
Figure 17. Connecting DDR2 Memory Controller for 32-Bit Connection
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_WE
DDR_RAS
DDR_CAS
CK
CK
CKE
CS
WE
RAS
CAS
DDR2
memory
x16−bit
DDR2
memory
controller
DDR_DQM[0]
DDR_DQM[1]
DDR_DQS[0]
DDR_DQS[1]
DDR_BA[2:0]
DDR_A[12:0]
DDR_D[15:0]
LDM
UDM
LDQS
UDQS
BA[2:0]
A[12:0]
DQ[15:0]
DDR_DQM[2]
DDR_DQM[3]
DDR_DQS[2]
DDR_DQS[3]
DDR_D[31:16]
DDR_ZN
CK
CK
CKE
CS
DDR2
memory
x16−bit
WE
DDR_ZP
RAS
CAS
LDM
UDM
LDQS
UDQS
BA[2:0]
A[12:0]
DQ[15:0]
200 Ω
200 Ω
Figure 18. Connecting DDR2 Memory Controller for 16-Bit Connection
DDR_CLK
DDR_CLK
DDR_CKE
DDR_CS
DDR_WE
DDR_RAS
DDR_CAS
CK
CK
CKE
CS
WE
RAS
CAS
DDR2
memory
x16−bit
DDR2
memory
controller
DDR_DQM[0]
DDR_DQM[1]
DDR_DQS[0]
DDR_DQS[1]
DDR_BA[2:0]
DDR_A[12:0]
DDR_D[15:0]
LDM
UDM
LDQS
UDQS
BA[2:0]
A[12:0]
DQ[15:0]
200 Ω
DDR_ZN
DDR_ZP
200 Ω
SPRU986B–November 2007
DDR2 Memory Controller
37
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Use Cases
3.2.1
Configuring SDRAM Bank Configuration Register (SDBCR)
The SDRAM bank configuration register (SDBCR) contains register fields that configure the DDR2
memory controller to match the data bus width, CAS latency, number of banks, and page size of the
attached DDR2 memory. In this example, we assume the following configuration:
•
•
•
•
Data bus width = 32 bits
CAS latency = 4
Number of banks = 8
Page size = 1024 words
dependent on whether or not it is desirable to unlock SDTIMR and SDTIMR2. The TIMUNLOCK bit should
only be set to 1 when the SDTIMR and SDTIMR2 needs to be updated.
Table 16. SDRAM Bank Configuration Register (SDBCR) Configuration
Field
Value Function Selection
TIMUNLOCK
x
Set to 1 to unlock the SDRAM timing register (SDTIMR) and the SDRAM timing register 2
(SDTIMR2). Cleared to 0 to lock SDTIMR and SDTIMR2.
To configure the DDR2 memory controller for a 32-bit data bus width.
To select a CAS latency of 4.
NM
0h
4h
3h
2h
CL
IBANK
PAGESIZE
To select 8 internal DDR2 banks.
To select 1024-word page size.
3.2.2
Configuring SDRAM Refresh Control Register (SDRCR)
The SDRAM refresh control register (SDRCR) configures the DDR2 memory controller to meet the refresh
requirements of the attached DDR2 device. SDRCR also allows the DDR2 memory controller to enter and
exit self refresh and enable and disable the MCLK stopping. In this example, we assume that the DDR2
memory controller is not is in self-refresh mode and that MCLK stopping is disabled.
The RR bit field in SDRCR is defined as the rate at which the attached DDR2 device is refreshed in DDR2
cycles. The value of this field may be calculated using the following equation:
RR = DDR2 clock frequency × DDR2 refresh rate
Table 17. DDR2 Memory Refresh Specification
Symbol
Description
Value
tREF
Average Periodic Refresh Interval
7.8 µs
Therefore, the following assumes a 133-MHZ DDR2 clock frequency:
RR = 133 MHZ × 7.8 µs = 1037.4
Therefore, RR = 1038 = 40Eh.
Table 18. SDRAM Refresh Control Register (SDRCR) Configuration
Field
Value Function Selection
SR
0
DDR2 memory controller is not in self-refresh mode.
MCLK stopping is disabled.
MCLKSTOPEN
RR
0
40Eh
Set to 40Eh DDR2 clock cycles to meet the DDR2 memory refresh rate requirement.
38
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Use Cases
3.2.3
Configuring SDRAM Timing Registers (SDTIMR and SDTIMR2)
The SDRAM timing register (SDTIMR) and SDRAM timing register 2 (SDTIMR2) configure the DDR2
memory controller to meet the data sheet timing parameters of the attached DDR2 device. Each field in
with the data sheet value. These tables also provide a formula to calculate the register field value and
displays the resulting calculation. Each of the equations include a minus 1 because the register fields are
defined in terms of DDR2 clock cycles minus 1. See Section 4.4 and Section 4.5 for more information.
Table 19. SDRAM Timing Register (SDTIMR) Configuration
DDR2 Data
Register Field
Name
Manual
Data Manual Formula
Register
Value
Parameter Name Description
Value (nS)
(Register field must be ≥)
T_RFC
T_RP
tRFC
tRP
Refresh cycle time
127.5
(tRFC × fDDR2_CLK) - 1
16
2
Precharge command to 20
refresh or activate
command
(tRP × fDDR2_CLK) - 1
T_RCD
tRCD
Activate command to
read/write command
20
(tRCD × fDDR2_CLK) - 1
2
T_WR
tWR
Write recovery time
15
45
(tWR × fDDR2_CLK) - 1
1
5
T_RAS
tRAS
Active to precharge
command
(tRAC × fDDR2_CLK) - 1
T_RC
tRC
Activate to Activate
command in the same
bank
65
10
(tRC × fDDR2_CLK) - 1
8
1
1
T_RRD
T_WTR
tRRD
Activate to Activate
command in a different
bank
((4 × tRRD) + (2 × tCK))/(4 × tCK) - 1
tWTR
Write to read command 10
delay
(tWTR × fDDR2_CLK) - 1
Note: The equation given above for the T_RRD field applies only for 8 bank DDR2 memories.
When interfacing to DDR2 memories with less than 8 banks, the T_RRD field should be
calculated using the following equation (tRRD × fDDR2_CLK) - 1.
Table 20. SDRAM Timing Register 2 (SDTIMR2) Configuration
DDR2 Data
Register Field
Name
Manual
Data Manual
Value
Formula (Register
field must be ≥)
Register
Value
Parameter Name Description
T_XSNR
tXSNR
Exit self refresh to a non-read
command
137.5 nS
(tXSNR × fDDR2_CLK) - 1 18
T_XSRD
tXSRD
Exit self refresh to a read
command
200 (tCK cycles) tXSRD - 1
199
T_RTP
T_CKE
tRTP
tCKE
Read to precharge command delay 7.5 nS
(tRTP × fDDR2_CLK) - 1
1
2
CKE minimum pulse width
3 (tCK cycles)
tCKE - 1
SPRU986B–November 2007
DDR2 Memory Controller
39
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
3.2.4
Configuring DDR PHY Control Register (DDRPHYCR)
The DDR PHY control register (DDRPHYCR) contains a read latency (READLAT) field that helps the
DDR2 memory controller determine when to sample read data. The READLAT field should be
programmed to a value equal to CAS latency plus round trip board delay minus 1. The minimum
READLAT value is CAS latency plus 1 and the maximum READLAT value is CAS latency plus 3 (again,
the READLAT field would be programmed to these values minus 1).
When calculating round trip board delay the signals of primary concern are the differential clock signals
(DDR_CLK and DDR_CLK) and data strobe signals (DDR_DQS). For these signals, calculate the round
trip board delay from the DDR2 memory controller to the memory and then choose the maximum delay to
determine the READLAT value. In this example we will assume the round trip board delay is 1 DDR_CLK
cycle, therefore READLAT can be calculated as follows:
READLAT = CAS latency + round trip board delay – 1 = 4 + 1 – 1 = 4
Table 21. DDR PHY Control Register (DDRPHYCR) Configuration
Register Field Name
Description
Register Value
DLLRESET
Programmed to remove the DDR2 memory controller DLL from
reset.
0
DLLPWRDN
READLAT
Programmed to power up the DDR2 memory controller DLL.
0
4
Read latency is equal to CAS latency plus round trip board delay
for data minus 1.
4
DDR2 Memory Controller Registers
controller. See the device-specific data manual for the memory addresses of these registers.
The DDR2 memory controller peripheral interfaces to the CPU using a 64-bit data bus and operates in
The DDR2 memory controller memory-mapped registers are 32-bit registers, and when accessing them
via the 64-bit interface, two 32-bit registers are accessed in each cycle. Therefore, for example, when
accessing the SDRAM bank configuration register (SDBCR) and the SDRAM refresh control register
(SDRCR), the following data is obtained:
D63-32
D31-0
SDRAM refresh control register (SDRCR)
SDRAM bank configuration register (SDBCR)
40
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
Table 22. DDR2 Memory Controller Registers Relative to Base Address 2000 0000h
Offset
Acronym
SDRSTAT
SDBCR
SDRCR
SDTIMR
SDTIMR2
PBBPR
IRR
Register Description
Section
4h
8h
SDRAM Status Register
Section 4.1
Section 4.2
Section 4.3
Section 4.4
Section 4.5
Section 4.6
Section 4.7
Section 4.8
Section 4.9
Section 4.10
Section 4.11
Section 4.12
SDRAM Bank Configuration Register
SDRAM Refresh Control Register
SDRAM Timing Register
Ch
10h
14h
20h
C0h
C4h
C8h
CCh
E4h
F0h
SDRAM Timing Register 2
Peripheral Bus Burst Priority Register
Interrupt Raw Register
IMR
Interrupt Masked Register
Interrupt Mask Set Register
Interrupt Mask Clear Register
DDR PHY Control Register
VTP IO Control Register
IMSR
IMCR
DDRPHYCR
VTPIOCR
Table 23. DDR2 Memory Controller Registers Relative to Base Address 01C4 2000h
Offset
Acronym
Register Description
Section
38h
DDRVTPR
DDR VTP Register
Section 4.13
Table 24. DDR2 Memory Controller Registers Relative to Base Address 01C4 0000h
Offset
Acronym
Register Description
Section
4Ch
DDRVTPER
DDR VTP Enable Register
Section 4.14
4.1 SDRAM Status Register (SDRSTAT)
Figure 19. SDRAM Status Register (SDRSTAT)
31
16
Reserved
R-4000h
15
3
2
1
0
Reserved
R-0
PHYRDY
R-0
Reserved
R-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset; -x = value is indeterminate after reset
Table 25. SDRAM Status Register (SDRSTAT) Field Descriptions
Bit
31-3
2
Field
Value Description
Reserved
PHYRDY
0
Reserved
DDR2 memory controller DLL ready. Reflects whether the DDR2 memory controller DLL is powered up
and locked.
0
1
0
DLL is not ready, either powered down, in reset, or not locked.
DLL is powered up, locked, and ready for operation.
Reserved
1-0
Reserved
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
41
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.2 SDRAM Bank Configuration Register (SDBCR)
The SDRAM bank configuration register (SDBCR) contains fields that program the DDR2 memory
controller to meet the specification of the attached DDR2 memory. These fields configure the DDR2
memory controller to match the data bus width, CAS latency, number of internal banks, and page size of
DDRDRIVE, CL, IBANK, and PAGESIZE bit fields will cause the DDR2 memory controller to start the
DDR2 SDRAM initialization sequence.
Figure 20. SDRAM Bank Configuration Register (SDBCR)
31
24
23
22
19
18
17
16
Reserved
R/W-1
BOOTUNLOCK
R/W-0
Reserved
R/W-2h
DDRDRIVE
R/W-1
Reserved
R-3h
15
14
13
12
11
9
8
TIMUNLOCK
R/W-0
NM
Reserved
R-0
CL
Reserved
R-0
R/W-0
R/W-5h
2
7
6
4
3
0
Reserved
R-0
IBANK
Reserved
R-0
PAGESIZE
R/W-0
R/W-2h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 26. SDRAM Bank Configuration Register (SDBCR) Field Descriptions
Bit
Field
Value Description
31-24 Reserved
0
Reserved. Always write a value of 0 to these bits.
23
BOOTUNLOCK
Boot unlock. Controls the write permission settings for the DDRDRIVE bit. To change the
DDRDRIVE bit value, use the following sequence:
1. Write a 1 to the BOOTUNLOCK bit.
2. Write a 0 to the BOOTUNLOCK bit along with the desired value of the DDRDRIVE bit.
0
1
DDRDRIVE bit may not be changed
DDRDRIVE bit may be changed
22-19 Reserved
2h
Reserved. Always write a value of 2h to these bits.
18
DDRDRIVE
DDR2 SDRAM drive strength. Configures the output driver impedance control value of the DDR2
SDRAM memory. To change the DDRDRIVE bit value, use the following sequence:
1. Write a 1 to the BOOTUNLOCK bit.
2. Write a 0 to the BOOTUNLOCK bit along with the desired value of the DDRDRIVE bit.
0
1
Normal drive strength.
Weak drive strength.
17-16 Reserved
3h
Reserved. Always write a value of 3h to these bits.
15
TIMUNLOCK
Timing unlock. Controls the write permission settings for the SDRAM timing register and SDRAM
timing register 2.
0
1
Register fields in the SDRAM timing register (SDTIMR) and the SDRAM timing register 2
(SDTIMR2) may not be changed.
Register fields in the SDRAM timing register (SDTIMR) and the SDRAM timing register 2
(SDTIMR2) may be changed.
14
NM
DDR2 data bus width.
32-bit bus width.
16-bit bus width
Reserved
0
1
0
13-12 Reserved
42
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
Table 26. SDRAM Bank Configuration Register (SDBCR) Field Descriptions (continued)
Bit
Field
Value Description
11-9
CL
0-7h
0-1h
2h
CAS latency.
Reserved
CAS latency of 2
CAS latency of 3
CAS latency of 4
CAS latency of 5
3h
4h
5h
6h-7h Reserved
8-7
6-4
Reserved
IBANK
0
0-7h
0
Reserved
Internal DDR2 bank setup. Defines the number of internal banks on the external DDR2 memory.
1 bank
1h
2h
3h
2 banks
4 banks
8 banks
4h-7h Reserved
3
Reserved
0
0-7h
0
Reserved. Always write a 0 to this bit.
2-0
PAGESIZE
DDR2 page size. Defines the page size of each page of the external DDR2 memory.
256-word page requiring 8 column address bits.
1h
2h
3h
512-word page requiring 9 column address bits.
1024-word page requiring 10 column address bits.
2048-word page requiring 11 column address bits.
4h-7h Reserved
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
43
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.3 SDRAM Refresh Control Register (SDRCR)
The SDRAM refresh control register (SDRCR) is used to configure the DDR2 memory controller to:
•
•
•
Enter and Exit the self-refresh state.
Enable and disable MCLK, stopping when in the self-refresh state.
Meet the refresh requirement of the attached DDR2 device by programming the rate at which the
DDR2 memory controller issues autorefresh commands.
Figure 21. SDRAM Refresh Control Register (SDRCR)
31
SR
30
29
24
23
22
16
0
MCLKSTOPEN
R/W-0
Reserved
R-0
Rsvd
R/W-0
Reserved
R-0
R/W-0
15
RR
R/W-884h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 27. SDRAM Refresh Control Register (SDRCR) Field Descriptions
Bit
Field
Value
Description
31
SR
Self refresh.
0
1
DDR2 memory controller exits the self-refresh mode.
DDR2 memory controller enters the self-refresh mode.
MCLK stop enable.
30
MCLKSTOPEN
0
1
Disables MCLK stopping, MCLK may not be stopped.
Enables MCLK stopping, MCLK may be stopped. The SR bit must be set to 1 before setting the
MCLKSTOPEN bit to 1.
29-24 Reserved
23 Reserved
22-16 Reserved
15-0 RR
0
Reserved
0
0
Reserved. Always write 0 to this bit.
Reserved
0-FFFFh
Refresh rate. Defines the rate at which the attached DDR2 devices will be refreshed. The value
of this field may be calculated with the following equation:
RR = DDR2 clock frequency (in MHZ) × DDR2 refresh rate (in µs)
where DDR2 refresh rate is derived from the DDR2 data sheet. Writing a value < 0100h to this
field causes it to be loaded with the value 2 × T_RFC from the SDRAM timing register
(SDTIMR).
44
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.4 SDRAM Timing Register (SDTIMR)
The SDRAM timing register (SDTIMR) configures the DDR2 memory controller to meet many of the AC
timing specification of the DDR2 memory. The SDTIMR register is programmable only when the
TIMUNLOCK bit is set to 1 in the SDBCR. Note that DDR_CLK is equal to the period of the DDR_CLK
signal. See the DDR2 memory data sheet for information on the appropriate values to program each field.
Figure 22. SDRAM Timing Register (SDTIMR)
31
15
25
24
22
6
21
5
19
3
18
16
T_RFC
T_RP
T_RCD
R/W-5h
T_WR
R/W-1Ah
R/W-5h
R/W-3h
11
10
2
1
0
T_RAS
R/W-9h
T_RC
T_RRD
R/W-3h
Rsvd
R-0
T_WTR
R/W-3h
R/W-Eh
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 28. SDRAM Timing Register (SDTIMR) Field Descriptions
Bit
Field
Value Description
31-25 T_RFC
0-7Fh Specifies the minimum number of DDR_CLK cycles from a refresh or load mode command to a refresh
or activate command, minus 1. Corresponds to the trfc AC timing parameter in the DDR2 data sheet.
Calculate by:
T_RFC = (trfc/DDR_CLK period) - 1
24-22 T_RP
21-19 T_RCD
18-16 T_WR
0-7h
0-7h
0-7h
Specifies the minimum number of DDR_CLK cycles from a precharge command to a refresh or activate
command, minus 1. Corresponds to the trp AC timing parameter in the DDR2 data sheet. Calculate by:
T_RP = (trp/DDR_CLK period) - 1
Specifies the minimum number of DDR_CLK cycles from an activate command to a read or write
command, minus 1. Corresponds to the trcd AC timing parameter in the DDR2 data sheet. Calculate by:
T_RCD = (trcd/DDR_CLK period) - 1
Specifies the minimum number of DDR_CLK cycles from the last write transfer to a precharge
command, minus 1. Corresponds to the twr AC timing parameter in the DDR2 data sheet. Calculate by:
T_WR = (twr/DDR_CLK period) - 1
When the value of this field is changed from its previous value, the initialization sequence will begin.
15-11 T_RAS
0-1Fh Specifies the minimum number of DDR_CLK cycles from an activate command to a precharge
command, minus 1. Corresponds to the tras AC timing parameter in the DDR2 data sheet. Calculate by:
T_RAS = (tras/DDR_CLK period) - 1
T_RAS must be greater than or equal to T_RCD.
10-6
5-3
T_RC
0-1Fh Specifies the minimum number of DDR_CLK cycles from an activate command to an activate
command, minus 1. Corresponds to the trc AC timing parameter in the DDR2 data sheet. Calculate by:
T_RC = (trc/DDR_CLK period) - 1
T_RRD
0-7h
Specifies the minimum number of DDR_CLK cycles from an activate command to an activate command
in a different bank, minus 1. Corresponds to the trrd AC timing parameter in the DDR2 data sheet.
Calculate by:
T_RRD = (trrd/DDR_CLK period) - 1
Note: for an 8 bank DDR2 device this field must be equal to ((4 × tRRD) + (2 × tCK)) / (4 × tCK) - 1.
2
Reserved
T_WTR
0
Reserved
1-0
0-3h
Specifies the minimum number of DDR_CLK cycles from the last write to a read command, minus 1.
Corresponds to the twtr AC timing parameter in the DDR2 data sheet. Calculate by:
T_WTR = (twtr/DDR_CLK period) - 1
SPRU986B–November 2007
DDR2 Memory Controller
45
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.5 SDRAM Timing Register 2 (SDTIMR2)
Like the SDRAM timing register (SDTIMR), the SDRAM timing register 2 (SDTIMR2) also configures the
DDR2 memory controller to meet the AC timing specification of the DDR2 memory. The SDTIMR2 register
is programmable only when the TIMUNLOCK bit is set to 1 in the SDBCR. See the DDR2 data sheet for
Figure 23. SDRAM Timing Register 2 (SDTIMR2)
31
15
25
24
Reserved
R/W-x
23
22
16
0
Reserved
R-0
T_XSNR
R/W-1Dh
8
7
5
4
T_XSRD
R/W-F1h
T_RTP
R/W-2h
T_CKE
R/W-5h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset; -x = value is indeterminate after reset
Table 29. SDRAM Timing Register 2 (SDTIMR2) Field Descriptions
Bit
Field
Value Description
31-25 Reserved
24-23 Reserved
22-16 T_XSNR
0
x
Reserved
Reserved. Reset value is indeterminate.
0-7Fh Specifies the minimum number of DDR_CLK cycles from a self-refresh exit to any other command
except a read command, minus 1. Corresponds to the txsnr AC timing parameter in the DDR2 data
sheet. Calculate by:
T_XSNR = (txsnr/DDR_CLK period) - 1
15-8
7-5
T_XSRD
T_RTP
T_CKE
0-FFh Specifies the minimum number of DDR_CLK cycles from a self-refresh exit to a read command,
minus 1. Corresponds to the txsrd AC timing parameter in the DDR2 data sheet. Calculate by:
T_XSRD = txsrd - 1
0-7h
Specifies the minimum number of DDR_CLK cycles from a last read command to a precharge
command, minus 1. Corresponds to the trtp AC timing parameter in the DDR2 data sheet. Calculate by:
T_RTP = (trtp/DDR_CLK period) - 1
4-0
0-1Fh Specifies the minimum number of DDR_CLK cycles between transitions on the DDR_CKE pin, minus 1.
Corresponds to the tcke AC timing parameter in the DDR2 data sheet. Calculate by:
T_CKE = tcke - 1
46
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.6 Peripheral Bus Burst Priority Register (PBBPR)
The peripheral bus burst priority register (PBBPR) helps prevent command starvation within the DDR2
memory controller. To avoid command starvation, the DDR2 memory controller momentarily raises the
priority of the oldest command in the command FIFO after a set number of transfers have been made.
The PR_OLD_COUNT bit sets the number of transfers that must be made before the DDR2 memory
controller raises the priority of the oldest command. The PBBPR is shown in Figure 24 and described in
Figure 24. Peripheral Bus Burst Priority Register (PBBPR)
31
15
16
Reserved
R-0
8
7
0
Reserved
R-0
PR_OLD_COUNT
R/W-FFh
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 30. Peripheral Bus Burst Priority Register (PBBPR) Field Descriptions
Bit
31-8
7-0
Field
Value Description
Reserved
0
Reserved
PR_OLD_COUNT
0-FFh Priority raise old counter. Specifies the number of memory transfers after which the DDR2
memory controller will elevate the priority of the oldest command in the command FIFO. Setting
this field to FFh disables this feature, thereby allowing old commands to stay in the FIFO
indefinitely.
0
1
2
1 memory transfer
2 memory transfers
3 memory transfers
3-FEh 4 to 255 memory transfers
FFh
Feature disabled, commands may stay in command FIFO indefinitely
SPRU986B–November 2007
DDR2 Memory Controller
47
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.7 Interrupt Raw Register (IRR)
The interrupt raw register (IRR) displays the raw status of the interrupt. If the interrupt condition occurs,
the corresponding bit in IRR is set independent of whether or not the interrupt is enabled. The IRR is
Figure 25. Interrupt Raw Register (IRR)
31
15
16
Reserved
R-0
3
2
LT
1
0
Reserved
R-0
Reserved
R-0
R/W1C-0
LEGEND: R/W = Read/Write; R = Read only; W1C = Write 1 to clear (writing 0 has no effect); -n = value after reset
Table 31. Interrupt Raw Register (IRR) Field Descriptions
Bit
31-3
2
Field
Value Description
Reserved
LT
0
Reserved
Line trap. Write a 1 to clear LT and the LTM bit in the interrupt masked register (IMR); a write of 0 has
no effect.
0
1
0
A line trap condition has not occurred.
Reserved
1-0
Reserved
48
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.8 Interrupt Masked Register (IMR)
The interrupt masked register (IMR) displays the status of the interrupt when it is enabled. If the interrupt
condition occurs and the corresponding bit in the interrupt mask set register (IMSR) is set, then the IMR
bit is set. The IMR bit is not set if the interrupt is not enabled in IMSR. The IMR is shown in Figure 26 and
Figure 26. Interrupt Masked Register (IMR)
31
15
16
Reserved
R-0
3
2
1
0
Reserved
R-0
LTM
Reserved
R-0
R/W1C-0
LEGEND: R/W = Read/Write; R = Read only; W1C = Write 1 to clear (writing 0 has no effect); -n = value after reset
Table 32. Interrupt Masked Register (IMR) Field Descriptions
Bit
31-3
2
Field
Value Description
Reserved
LTM
0
Reserved
Line trap masked. Write a 1 to clear LTM and the LT bit in the interrupt raw register (IRR); a write of 0
has no effect.
0
1
A line trap condition has not occurred.
details.
1-0
Reserved
0
Reserved
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
49
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.9 Interrupt Mask Set Register (IMSR)
The interrupt mask set register (IMSR) enables the DDR2 memory controller interrupt. The IMSR is shown
Note: If the LTMSET bit in IMSR is set concurrently with the LTMCLR bit in the interrupt mask clear
register (IMCR), the interrupt is not enabled and neither bit is set to 1.
Figure 27. Interrupt Mask Set Register (IMSR)
31
15
16
Reserved
R-0
3
2
1
0
Reserved
R-0
LTMSET
R/W-0
Reserved
R-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 33. Interrupt Mask Set Register (IMSR) Field Descriptions
Bit
31-3
2
Field
Value Description
Reserved
LTMSET
0
Reserved
Line trap interrupt set. Write a 1 to set LTMSET and the LTMCLR bit in the interrupt mask clear register
(IMCR); a write of 0 has no effect.
0
1
0
Line trap interrupt is not enabled; a write of 1 to the LTMCLR bit in IMCR occurred.
Line trap interrupt is enabled.
Reserved
1-0
Reserved
50
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.10 Interrupt Mask Clear Register (IMCR)
The interrupt mask clear register (IMCR) disables the DDR2 memory controller interrupt. Once an interrupt
Note: If the LTMCLR bit in IMCR is set concurrently with the LTMSET bit in the interrupt mask set
register (IMSR), the interrupt is not enabled and neither bit is set to 1.
Figure 28. Interrupt Mask Clear Register (IMCR)
31
15
16
Reserved
R-0
3
2
1
0
Reserved
R-0
LTMCLR
R/W1C-0
Reserved
R-0
LEGEND: R/W = Read/Write; R = Read only; W1C = Write 1 to clear (writing 0 has no effect); -n = value after reset
Table 34. Interrupt Mask Clear Register (IMCR) Field Descriptions
Bit
31-3
2
Field
Value Description
Reserved
LTMCLR
0
Reserved
Line trap interrupt clear. Write a 1 to clear LTMCLR and the LTMSET bit in the interrupt mask set
register (IMSR); a write of 0 has no effect.
0
1
0
Line trap interrupt is not enabled.
Line trap interrupt is enabled; a write of 1 to the LTMSET bit in IMSR occurred.
Reserved
1-0
Reserved
SPRU986B–November 2007
Submit Documentation Feedback
DDR2 Memory Controller
51
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.11 DDR PHY Control Register (DDRPHYCR)
The DDR PHY control register (DDRPHYCR) configures the DDR2 memory controller DLL for operation
and determines whether the DLL is in reset, whether it is powered up, and the read latency. The
Figure 29. DDR PHY Control Register (DDRPHYCR)
31
15
16
Reserved
R/W-5000h
6
5
4
3
2
0
Reserved
R/W-190h
DLLRESET DLLPWRDN Rsvd
R/W-0 R/W-1 R-1
READLAT
R/W-7h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 35. DDR PHY Control Register (DDRPHYCR) Field Descriptions
Bit
Field
Value
5000h
190h
Description
31-16 Reserved
Reserved. Always write 5000h to these bits.
Reserved. Always write 190h to these bits.
Reset DLL.
15-6
5
Reserved
DLLRESET
0
1
DLL is out of reset.
Places the DLL in reset.
Power down DLL.
4
DLLPWRDN
0
1
DLL is powered up.
DLL is powered down, if DLLPWRDN and the SR bit and MCLKSTOPEN bit in the SDRAM
refresh control register (SDRCR) are set to 1.
3
Reserved
READLAT
1
Reserved
2-0
0-7h
Read latency. Read latency is equal to CAS latency plus round trip board delay for data
minus 1. The maximum value of read latency that is supported is CAS latency plus 3. The
minimum read latency value that is supported is CAS latency plus 1. The read latency value
is defined in number of MCLK/DDR_CLK cycles.
52
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.12 VTP IO Control Register (VTPIOCR)
The VTP IO control register (VTPIOCR) is used to control the calibration of the DDR2 memory controller
IOs with respect to voltage, temperature, and process (VTP). The voltage, temperature, and process
Figure 30. VTP IO Control Register (VTPIOCR)
31
15
16
Reserved
R-0
14
13
12
Reserved
R/W-0
11
10
9
5
4
0
RECAL Rsvd
EN
Rsvd
R-0
PCH
NCH
R/W-0 R/W-0 R/W-0
R/W-0
R/W-1Fh
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 36. VTP IO Control Register (VTPIOCR) Field Descriptions
Bit
Field
Value Description
31-16 Reserved
0
Reserved
15
RECAL
Start VTP IO calibration.
Normal operation
0
1
0
Transition from 0 to 1 starts VTP IO calibration.
Reserved. Always write a 0 to this bit.
VTP enable.
14
13
Reserved
EN
0
1
0
0
VTP IO calibration is disabled.
VTP IO calibration is enabled.
Reserved. Always write a 0 to this bit.
Reserved
12-11 Reserved
10
Reserved
PCH
9-5
0-1Fh P channel value. This value is driven to the IO to calibrate the impedance of the IO. The value of PCH
4-0
NCH
0-1Fh N channel value. This value is driven to the IO to calibrate the impedance of the IO. The value of NCH
SPRU986B–November 2007
DDR2 Memory Controller
53
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR2 Memory Controller Registers
4.13 DDR VTP Register (DDRVTPR)
The DDR VTP register (DDRVTPR) is used in conjunction with the VTP IO control register (VTPIOCR) to
calibrate the output impedance of the DDR2 memory controller IOs with respect to voltage, temperature,
and process. Following the calibration sequence, DDRVTPR contains the information needed to calibrate
the impedance of the IO. Once the calibration sequence has completed, DDRVTPR should be read and
Figure 31. DDR VTP Register (DDRVTPR)
31
15
16
Reserved
R-0
10
9
5
4
0
Reserved
R-0
PCH
R-0
NCH
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 37. DDR VTP Register (DDRVTPR) Field Descriptions
Bit
Field
Value Description
Reserved.
31-10 Reserved
0
9-5
4-0
PCH
NCH
0-1Fh P channel value for IO impedance calibration. Following the VTP calibration sequence, this value should
be read and written to the PCH field in the VTP IO control register (VTPIOCR).
0-1Fh N channel value for IO impedance calibration. Following the VTP calibration sequence, this value
should be read and written to the NCH field in the VTP IO control register (VTPIOCR).
4.14 DDR VTP Enable Register (DDRVTPER)
The DDR VTP enable register (DDRVTPER) is used to enable/disable accesses to the DDR VTP register
(DDRVTPR). Writing a value of 1 to DDRVTPER enables accesses to DDRVTPR and writing a value of 0
Figure 32. DDR VTP Enable Register (DDRVTPER)
31
15
16
Reserved
R-0
1
0
Reserved
R-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
EN
R/W-0
Table 38. DDR VTP Enable Register (DDRVTPER) Field Descriptions
Bit
31-1
0
Field
Value Description
Reserved
EN
0
Reserved. Always write 0 to these bits.
DDRVTPR access enable.
0
1
Access to DDRVTPR is disabled.
Access to DDRVTPR is enabled.
54
DDR2 Memory Controller
SPRU986B–November 2007
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Appendix A Revision History
Table A-1. Document Revision History
Reference
Global
Additions/Modifications/Deletions
Changed DDR_CLKO to DDR_CLK in text, figures, and tables.
Changed DDR_CLKO to DDR_CLK in text, figures, and tables.
Changed DDR_BS[2:0] to DDR_BA[2:0] in text, figures, and tables.
Changed paragraph.
Global
Global
Section 2.1
Section 2.1.1
Figure 2
Changed subsection.
Changed figure.
Figure 3
Changed figure.
Table 2
Changed pin name for Clock and Bank address.
Changed signal name for Clock and Bank address.
Changed signal name for Clock and Bank address.
Changed signal name for Clock and Bank address.
Changed third sentence.
Figure 4
Figure 5
Figure 6
Section 2.4.3
Figure 7
Changed signal name for Clock and Bank address.
Changed third sentence in first paragraph.
Changed signal names.
Section 2.4.4
Figure 8
Figure 9
Changed signal names.
Section 2.4.6
Figure 10
Table 15
Changed second sentence in second paragraph.
Changed signal name for Clock and Bank address.
Changed DDR_A[10] value.
Figure 16
Section 2.16.1
Figure 17
Figure 18
Section 3.2.2
Table 27
Changed figure.
Changed step 2 in second paragraph.
Changed figure.
Changed figure.
Changed RR equation in second paragraph.
Changed equation in Description of RR bits 15-0.
Changed equation in Description of bits.
Changed equation in Description of T_XSNR bits 22-16.
Changed equation in Description of T_RTP bits 7-5.
Changed Value and Description of Reserved bits 31-6.
Table 28
Table 29
Table 35
SPRU986B–November 2007
Revision History
55
Submit Documentation Feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
Automotive
Broadband
Digital Control
Military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
microcontroller.ti.com
Telephony
Low Power
Wireless
Video & Imaging
Wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
Download from Www.Somanuals.com. All Manuals Search And Download.
|