Installation, Operation & Diagnostics
for the
MIU2.4
MIU9.6
MIU14.4
MIU28.8
Industrial Grade Dial Modems
Book 1 of 2
(See Book 2 for AT Commands)
Document No. 49-0002-001 Rev.A
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE of CONTENTS
1. STANDARDS ....................................................................................Page 2
2. PRODUCT OVERVIEW ...................................................................Page 3
3. GENERAL PRODUCT SPECIFICATIONS .....................................Page 5
4. POWER MODES ...............................................................................Page 6
5. MODEM SPECIFICATIONS ............................................................Page 7
6. POWER CONNECTIONS.................................................................Page 8
7. SERIAL DATA PORT PIN-OUTS....................................................Page 9
8. DIP SWITCHES............................................................................... Page 10
9. LED INDICATOR ........................................................................... Page 11
10. AUTO RESET FEATURE............................................................... Page 11
11. AUTO DIAL FEATURE.................................................................. Page 11
12. OUTLINE DRAWING & MOUNTING.......................................... Page 12
13. MODEM CONFIGURATION......................................................... Page 13
14. FACTORY CONFIGURATION...............................................Page 14 - 17
15. DIAGNOSTICS.........................................................................Page 18 – 28
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. STANDARDS
All Telenetics dial-up modems are designed to meet the following Standards:
USA:
FCC Part 15, Class A and Part 68
Canada:
DOC Standards CS-01, CS-02 and CS-03
CANADIAN DEPARTMENT OF COMMUNICATION NOTICE
NOTICE: The Canadian Department of Communications (DOC) label identifies certified
equipment. This certification means that the equipment meets certain telecommunications network
protective, operational and safety requirements. The department does not guarantee the equipment
will operate to the user’s satisfaction.
Before installing this equipment, make sure you are permitted to connect it to the facilities of the
local telecommunications company. You must install the equipment using an acceptable method of
connection. In some cases you may also extend the company’s inside wiring for single line
individual service by means of certified connector assembly (telephone extension cord). You should
be aware, however, that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designed by the supplier. Any repairs or alterations made by a user to this equipment, or equipment
malfunctions, may give the telephone communications company cause to request the user to
disconnect the equipment.
For your own protection, make sure that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution: Do not attempt to make electrical ground connections yourself, contact the appropriate
electric inspection authority or an electrician.
NOTICE: The load number (LN) assigned to each terminal device denotes the percentage of the
total load to the telephone loop used by the device, to prevent overloading. The termination on a
loop may consist of any combination of devices, subject to the requirement that the total of the load
numbers of all the devices does not exceed 100.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
PRODUCT OVERVIEW
The MIU2.4, MIU9.6, MIU14.4 & MIU28.8 are industrial grade dial
modems for connection to the Public Switched Telephone Network..
They can be powered from a wide range of AC and DC power supplies,
they are internally surge protected on both the power and analog lines,
and they will operate in temperatures from -40 to +85 deg C.
Internally, each unit consists of a baseboard and a communication
module. The baseboard includes the power supply regulation and surge
protection. The communication module is a Telenetics™ Pony
Express™ Dial Modem Module.
The MIU is packaged specifically for the harsh environments found in
utility substations and industrial facilities. Though functionally similar to
commercial modems, the MIU includes special features that make it
particularly well suited for utility and industrial applications:
Environment:
Power Supply:
Low Power:
The MIU has been designed specifically for use in
harsh environments. In addition to an extended
temperature range (-40 to +85º C), the MIU includes
surge, shock, vibration, and safety features superior
to those of conventional commercial modems.
The MIU can be powered from a broad range of AC
and DC power supplies, such as an auxiliary supply
(eg; 12VDC) from another piece of equipment,
125VDC from a station battery or a standard
120VAC.
The MIU dial modem can be configured to enter into
a “power down” mode. In this mode, an MIU will
consume only a small fraction of its active power
while waiting for either controller or telephone
activity.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Industrial:
The MIU is packaged in a rugged, compact, non-
metallic (ABS) enclosure. Designed for unmanned
locations, the MIUs do not include the array of
pushbuttons and LEDs normally associated with
consumer-type modems. Configuration is by dip
switches and/or software (“AT”) commands.
Standard industrial connectors for data, analog and
power interfaces allow reliable interconnection to
other industrial components.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. GENERAL PRODUCT SPECIFICATIONS
Dimensions:
Weight:
5.3 x 4.0 x 1.375 inches
1 lb
Voltage Supply: Standard Model:
LV Model (Suffix “-LV”):
40 to 270VDC
40 to 270VAC, 50/60Hz
9 to 36VDC
Current Requirements: (See Section 4 for Power Down Modes)
MIU2.4:
12VDC
24VDC
125VDC
120VAC
220VAC
65mA
27mA
7.5mA
6.5mA
5.5mA
MIU9.6:
12VDC
115mA
24VDC
57mA
125VDC
11mA
120VAC
10mA
220VAC
9mA
MIU14.4:
12VDC
24VDC
125VDC
120VAC
220VAC
160mA
69mA
14mA
12mA
9mA
MIU28.8:
12VDC
24VDC
125VDC
120VAC
220VAC
205mA
125mA
16mA
15mA
11mA
Surge Protection:
Power Supply: 8kVrms
Analog Line:
5kVac (MIU2.4 & 9.6)
3.75kVac (MIU14.4 & 28.8)
ESD ± 10kV
Digital Line:
Operating Temperature:
Operating Humidity:
Storage Temperature:
-40 to +85 deg C
0 to 90% (non-condensing.)
-55 to 100 deg C
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. POWER MODES
Mode
Description
Power
Consumption
See Section 3
Power On
Sleep
Factory Setting: Full power is always
available to the modem.
If the modem is on hook for a
predetermined period (PE2400 = 5
seconds; PE2496, PE14.4 & PE28.8 =
software configured: Set S24 to desired
delay in seconds), it will drop to a low
current mode).
Approx. 6mA
The modem will instantly “wake up” to
full power by either an incoming ring
signal or any transmit data (TxD) signal.
If the modem is on hook for 30 seconds,
it will automatically turn “off”.
Power Down
Approx. 20µA
The modem will automatically turn “on”
to full power within 400ms of receiving a
DTR signal or an incoming call.
The power mode is set by a dip switch on the Pony Express Modem Module
inside the MIU case. Factory default is Power On mode. Other modes are set at
the factory before shipment if requested. Other modes can be set in the field ~
call Telenetics for an instruction sheet.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. MODEM SPECIFICATIONS
MIU2.4
MIU9.6
V.22bis
V.22
Bell212A
Bell 103
MIU14.4
V.32bis
V.32
V.22bis
V.22
MIU28.8
V.34
V.32bis
V.32
V.22bis
V.22
Bell212A
Bell 103
Standards
V.22bis
V.22
Bell212A
Bell 103
Bell212A
Bell 103
Modem Line
Speed
(Asynch)
2400bps
1200bps
300bps
2400bps
1200bps
300bps
14400bps
9600bps
4800bps
2400bps
1200bps
300bps
28800bps
19200bps
14400bps
9600bps
4800bps
2400bps
1200bps
300bps
DTE Rates
above Modem
Line Speeds
-
-
19200bps
9600bps
4800bps
57600bps
38400bps
19200bps
115200bps
57600bps
38400bps
19200bps
Error
Correction &
Data
MNP 2,3,5
& 10
MNP 2,3,5
& 10
MNP 2,3,5
& 10
V.42
V.42
V.42
Compression
V.42bis
V.42bis
V.42bis
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. POWER CONNECTIONS
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. SERIAL DATA PORT PIN-OUTS
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
8. DIP SWITCH SETTINGS
Not Applicable
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. LED INDICATOR
The MIU has a single LED that will indicate the following conditions...
4
4
Blinking: POWER ON
Steady: MODEM CONNECTED (CARRIER DETECT)
10. AUTO RESET FEATURE
The dial-up modem modules inside your MIU include an “Auto Reset”
feature: If the modem configuration is lost for any reason, it can be
restored by dialing the modem and allowing it to ring 4 to 6 times.
The Auto Reset feature is enabled and disabled by a dip switch on the
modem module. Your MIU will have been shipped with the Auto Reset
mode active, unless otherwise specified at the time of ordering. Please
consult Telenetics if you wish to open up your MIU to disable Auto
Reset.
11. AUTO DIAL FEATURE
The dial-up modem modules inside your MIU include a software
configured “Auto Dial” feature: Command AT\D1 will enable Auto
Dial: When DTR goes from an OFF to ON condition, and \D1 is set, the
modem will auto dial the phone number stored in location & Z0 (up to 45
digits).
Command \D0 (default) will disable the Auto Dial feature.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
12. OUTLINE DRAWING & MOUNTING
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
13. MODEM CONFIGURATION
Telenetics dial and leased line modems are based upon Rockwell
chipsets. These chipsets contain Rockwell’s “AT” command set.
A summary of the Rockwell command set for your MIU modem is
provided in Book 2.
Unless otherwise specified at the time of order, your modem will have
left the Telenetics factory in the configuration detailed on the following
pages.
The Telenetics factory configuration differs from the Rockwell default
configuration as follows...
&C0
&C1
Rockwell Default
Telenetics Factory
Carrier Detect (CD) always ON.
Carrier Detect (CD) only ON
when modem connected (on hook)
S0=0
S0=1
Rockwell Default
Telenetics Factory
Auto-Answer OFF
Auto-Answer on first ring
You can review the configuration of your modem by entering AT&V
<CR>.
You can restore the Rockwell factory configuration by entering
AT&F&W
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
14. FACTORY CONFIGURATION ~ MIU2.4
ACTIVE PROFILE:
B1 E1 L2 M1 Q0 V1 X4 Y0 &C1 &D0 &G0 &J0 &L0 &P0 &Q0
&R0 &S0 &X0 &Y0 S00:001 S01:000 S02:043 S03:013 S04:010
S05:008 S06:002 S07:030 S08:002 S09:006 S10:014 S12:050
S14:AAH S16:00H S S18:000 S21:00H S22:76H S23:15H S25:005
S26:001 S27:40H S28:00H
STORED PROFILE 0:
B1 E1 L2 M1 Q0 V1 X4 Y0 &C1 &D0 &G0 &J0 &L0 &P0 &Q0
&R0 &S0 &X0 S00:001 S14:AAH S18:000 S21:00H S22:76H
S23:17H S25:005 S26:001 S27:40H S28:00H
STORED PROFILE 1:
B1 E1 L2 M1 Q0 V1 X4 Y0 &C0 &D0 &G0 &J0 &L0 &P0 &Q0
&R0 &S0 &X0 S00:000 S14:AAH S18:000 S21:00H S22:76H
S23:17H S25:005 S26:001 S27:40H S28:00H
TELEPHONE NUMBERS
&Z0=
&Z1=
&Z2=
&Z3=
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
14. FACTORY CONFIGURATION ~ MIU9.6
ACTIVE PROFILE:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 &Y0 S00:001 S01:000 S02:043 S03:013
S04:010 S05:008 S06:002 S07:050 S08:002 S09:006 S10:014
S11:095 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000
S38:020 S44:020 S46:138 S48:007 S95:000
STORED PROFILE 0:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 S00:001 S02:043 S06:002 S07:050
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:168 S41:195 S46:138 S95:046
STORED PROFILE 1:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 S00:001 S02:043 S06:002 S07:050
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:168 S41:195 S46:138 S95:000
TELEPHONE NUMBERS:
0=
2=
1=
3=
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
14. FACTORY CONFIGURATION ~ MIU14.4
ACTIVE PROFILE:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 &Y0 S00:001 S01:000 S02:043 S03:013
S04:010 S05:008 S06:002 S07:050 S08:002 S09:006 S10:014
S11:095 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000
S38:020 S44:020 S46:138 S48:007 S95:000
STORED PROFILE 0:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 S00:001 S02:043 S06:002 S07:050
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:168 S41:195 S46:138 S95:046
STORED PROFILE 1:
B1 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D2 &G0 &J0 &K3
&Q5 &R1 &S0 &T5 &X0 S00:001 S02:043 S06:002 S07:050
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:168 S41:195 S46:138 S95:000
TELEPHONE NUMBERS:
0=
2=
1=
3=
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
14. FACTORY CONFIGURATION ~ MIU28.8
ACTIVE PROFILE:
B0 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D0 &G2 &J0 &K3
&Q5 &R1 &S0 &T4 &X0 &Y0 S00:001 S01:000 S02:043 S03:013
S04:010 S05:008 S06:002 S07:030 S08:002 S09:006 S10:014
S11:255 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000
S38:020 S46:138 S48:007 S95:000
STORED PROFILE 0:
B0 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D0 &G2 &J0 &K3
&Q5 &R1 &S0 &T4 &X0 S00:001 S02:043 S06:002 S07:030
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:105 S41:003 S46:138 S95:000
STORED PROFILE 1:
B0 E1 L1 M1 N1 Q0 T V1 W0 X4 Y0 &C1 &D0 &G2 &J0 &K3
&Q5 &R1 &S0 &T4 &X0 S00:001 S02:043 S06:002 S07:030
S08:002 S09:006 S10:014 S11:095 S12:050 S18:000 S36:007
S37:000 S40:105 S41:003 S46:138 S95:000
TELEPHONE NUMBERS:
0=
2=
1=
3=
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
15. DIAGNOSTICS
The following pages provide software and hardware techniques for
diagnosing communication problems and thereby isolating the problem at
either the local modem, the remote modem or the interconnecting line.
The following AT&Tn commands form part of the CCITT V.54 protocol
and can be used for diagnostic testing.
Note: &Tn commands can only be used when the modem is configured
for &Q0 <CR> (unbuffered/direct asynchronous mode).
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
&T0 TERMINATE TEST IN PROGRESS
If a V.54 loopback test is in progress as a result of executing an &Tn
command, then the &T0 command will cause that test to be terminated,
provided that the modem is in the command state or a V.54 state that
accepts commands from the DTE. See specific &Tn command
descriptions for termination actions.
&T1 INITIATE LOCAL ANALOG LOOPBACK (See Figure 2)
When the AT&T1 command is entered, the modem goes on hook and
configures itself for analog loopback. DSR is turned off (if &S1 is in
effect), the analog loopback state is entered, and the test timer is set to
the value in S18. A connect result code is sent to the DTE, and the test
timer then begins its count down. The test terminates when the test
timer expires. If S18 equals 0, then the test must be terminated by an
&T0, H0, or Z command. While any command may be entered while
the modem is in this test state, the modem response is not specified
except for H0, &T0 and Z, any of which will terminate the test. Upon
termination of the test, the modem enters the command state.
RESULT CODE
CONNECT
ERROR
DESCRIPTION
When local analog loopback state is
entered.
If any other &Tn test is active (except
&T0) or if in the on-line command
state.
OK
After test is stopped by test timer, the
H0 command, or the &T0 command.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
&T2 NO FUNCTION
&T3 PERFORM LOCAL DIGITAL LOOPBACK (See Figure 3)
The modem must be in the command state with connection established
when this command is issued, otherwise an ERROR result code occurs.
The AT&T3 command establishes a loopback of received data, after
demodulation, and sends it back to the distant end. The modem is
configured for local digital loopback, DSR is turned off (if &S1 is in
effect), the test timer is started with the value in S18, and an OK result
code is sent to the DTE. If S18 contains a 0, the test must be terminated
by a &T0, H0, or Z command. The latter two result in the modem going
on hook. If S18 does not contain 0, the test is terminated after the
number of seconds stored in S18.
RESULT CODE
DESCRIPTION
OK
After 2 second delay
ERROR
If any other self test is active (&T1,
&T6, &T7 or &T8) or if in idle state.
When test is terminated.
&T4 GRANT REMOTE DIGITAL LOOPBACK (RDL) REQUESTS
When in the on-line state, the modem will honor a remote digital
loopback request from a distant modem if it occurs. This will result in an
ERROR if the command is given while any V.54 test is active (&T1,
&T3, &T6, &T7 or &T8).
NOTE: There are data patterns that may cause a Remote Digital
Loopback conditions. Care should be given to the type of data being
received so that no RDL modes will be initiated.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
&T5 DENY RDL REQUESTS
The modem will not respond to a remote digital loopback request from a
distant modem. This will result in an error if the command is given
while any V.54 test is active (&T1, &T3, &T6, &T7 or &T8).
&T6 INITIATE REMOTE DIGITAL LOOPBACK (See Figure 4)
The command is valid only if the modem is in the command state with a
connection established.
Configure the modem under test with an AT&T4 command so that it
will honor a remote digital loopback request.
Enter AT&T6 at the local modem and it will send a remote digital
loopback request to the remote modem. After the RDL
acknowledgement signal is received from the remote modem, DSR is
turned off (if &S1 is in effect), the on-line state is entered, a CONNECT
result code is sent to the DTE, and the test timer is set to the value in
S18.
If the local modem does not receive the RDL acknowledgment signal
from the remote end in three seconds, it sends an ERROR result code to
the DTE and returns to the command state. The local modem sends the
signal to release the remote digital loopback when the test is terminated.
The test may be terminated by the H0, Z, or &T0 command. The test
will also terminate when the test timer expires (sending the modem to
the command state) or carrier is lost (causing a NO CARRIER result
code and the modem to go on hook in the command state).
RESULT CODE
DESCRIPTION
CONNECT
ERROR
When on-line state is entered.
If any V.54 test is active (&T1, &T3,
&T6-&T8).
ERROR
ERROR
If not in on-line command state.
If the RDL signal is not acknowledged.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
&T7 INITIATE RDL WITH LOCAL SELF TEST (See Figure 5)
This is a system test, end to end.
The command is valid only if the modems are in the command state with
a connection established.
Configure the remote modem with an AT&T4 command so that it will
honor a remote digital loopback request.
Enter AT&T7 at the local modem and it will send a digital loopback
request to the remote modem. After the RDL acknowledgment signal is
received from the remote modem, DSR is turned off (if &S1 is in
effect), the on-line state is entered, an OK result code is sent to the DTE,
and the test timer is set to the value in S18. While the test is active, the
local modem sends a test message to the remote modem and counts the
errors in the received (looped back) signal. The modems stay in the
command state during the test. When the test is terminated (except by a
loss of carrier), the local modem sends the release signal to the remote
modem, as in &T6, and reports the three-digit error count to the DTE.
The information text is followed by an OK result code. The test is
terminated by loss of carrier, or an H0, &T0, or Z command, and by the
S18 timer running out.
RESULT CODES
DESCRIPTION
OK
OK
When command executed is started.
After error count is sent to DTE (&T1,
&T3, &T6, &T7 or &T8).
ERROR
ERROR
If not in on-line command state.
If the RDL signal is not acknowledged.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
&T8 LOCAL LOOPBACK WITH SELF TEST (See Figure 6)
The modem should be on hook. Enter AT&T8 to configure the modem
for analog loopback and self test. The test timer is started at the time
indicated by S18, DSR is turned off (if &S1 is in effect). A self test
condition is entered, and an OK result code is sent to the DTE. During
the test the modem sends a test message and counts errors in the looped
back signal. The test is terminated when the timer times out (S18) or the
&T0, H0, or Z command is issued. When the test is terminated, the
three digit error count is sent to the DTE. An OK result code follows
the error count.
RESULT CODE
DESCRIPTION
OK
If a test state is entered.
OK
ERROR
After error count is sent to DTE
If any other V.54 test is active (&T1, &T3,
&T6, &T7), or if on-line.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL TEST / DIAGNOSTICS COMMANDS...
%L
RECEIVED SIGNAL LEVEL
Returns a value (-dBm) which indicates the received signal
level at modem DATA PUMP interface. This value is
determined by the loss/gain of modem Telco Interface circuit
±dB at the Tip/Ring input to the modem. Typical value
should be -25dBm to -35dBm for most Telco connections.
%Q
RECEIVED LINE SIGNAL QUALITY
Reports the line signal quality at the modem DATA PUMP
interface. This signal is also dependent on the DAA circuit
(Telco Interface). Returns the higher order byte of the EQM
(Eye Quality Monitor is the filter squared magnitude of the
error vector). Typical value should be below 10. The lower
the number, the better the performance from the modem.
ERROR response if NO connection to remote modem.
In &T1, modem %Q will be 0.
S86
CONNECTION FAILURE CAUSE
S86 can help determine the cause of a connection failure.
When the modem issues a NO CARRIER result code, a value
is written to this register. To read this register, following the
connection failure, issue ATS86? <CR>. The modem will
report one of the following values...
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
0
4
5
Normal hang up; no error occurred.
Physical carrier loss. (Loss of Carrier)
Feature negotiation failed to detect presence of another V.42
error-control modem at other end.
6
7
Other error-control modem did not respond to
feature negotiation message sent by this modem.
Other modem is synchronous-only; this modem is
asynchronous-only.
8
Modems could not find a common framing technique.
Modems could not find a protocol in common.
Feature negotiation message sent by other modem incorrect.
Synchronous information (data of flags) not received from
other modem.
9
10
11
12
13
Normal disconnect initiated by other modem.
Other modem did not respond after many transmissions of the
same message. Modem made 10 attempts then hung up.
Protocol violation occurred.
14
15
Compression failure.
Note: Multiple occurrences may contribute to a NO CARRIER
message; S86 records the first event that occurred.
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
MIU Installation, Operation & Diagnostics Edition: March 30, 1998
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
|