User Guide
SP330
Speaker dock for iPhone/iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
Warning: To reduce the risk of fire or electrical shock,
do not expose this product to rain or moisture. The
product must not be exposed to dripping and splashing
and no object filled with liquids such as a vase of
flowers should be placed on the product.
IMPORTANT
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, this
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one of the following measures:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
This symbol indicates that there are impor-
tant operating and maintenance instructions
in the literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
No naked flame sources such as candles should be
placed on the product.
Caution: Changes or modifications not expressly
approved by the manufacturer could void the user’s
authority to operate this device.
Caution: Usage of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous exposure.
-
-
Connect the equipment into an outlet on
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
a
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a slightly damp cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
ELECTRICAL INFORMATION
Use this appliance only with the supplied AC Adaptor.
Using non-approved power supplies will void the
warranty.
Mains Supply: The mains operating voltage of the
AC Adaptor is marked on a rating plate on the AC
Adaptor.
Do not install or operate near any heat sources such
as radiators, stoves, or other apparatus that produce
heat.
The means of disconnecting this appliance from
the mains supply is the AC adaptor. This should be
unobstructed and readily operable at all times.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
PRELIMINARIES
INDEX
INDEX
UNPACKING
The SP330 is a stylish, remote controlled iPhone/iPod
docking station with dual reflex speakers and with a video
output to feed video programs from video equipped iPhone/iPod
models to a TV.
Carefully unpack the unit. If it is damaged, please return it to
your nearest Tesco store for replacement. Remember to take
your purchase receipt with you.
Retain the User Handbook. If you pass the unit on to a third
party make sure you pass on the handbook.
Important safety information..................................1
Introduction ............................................................2
Unpacking ...............................................................2
Controls and connections.........................................3
Remote control........................................................5
Adaptors..................................................................6
Getting started ........................................................7
Power control ..........................................................7
Docking and playing an iPod ...................................7
Volume control, selecting a source...........................8
Video connection and playback ...............................9
Tone controls .........................................................10
Troubleshooting ....................................................10
Care & Maintenance...............................................10
........................................................10
We suggest you retain the packaging. If you dispose of it, do
so having regard to any recycling regulations in your area.
CONTENTS
The carton should contain:
•
•
•
•
•
•
•
The SP330 docking station
AC adaptor
Remote control including battery
Set of 3 x iPhone/iPod adaptors
Video out cable (yellow plugs)
Audio in cable (grey plugs)
Operating Manual
If any items are missing or damaged, contact your nearest
TESCO store for a replacement. Have your receipt ready when
you call. Retain the packaging. If you dispose of it, do so
having regard to any recycling regulations in your area.
Warranty ...............................................................10
LOCATION
Place the unit on dry stable surface away from heat and
damp and where it is unlikely to fall or be knocked over.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTIONS
FRONT VIEW
Standby button
Source select button
Mute button
Volume down button
Volume up button
iPhone/iPod docking connector
iPhone/iPod dock adaptor
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTIONS
BACK VIEW
a
b
c
Audio In jack
Video Out jack
DC In jack
4
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL BATTERIES
REMOTE CONTROL
BATTERY DISPOSAL
BEFORE FIRST USE
To prepare the remote control for first use, pull out the safety
strip to activate the battery.
Dispose of used batteries with regard to the recycling
regulations in your area. Do NOT short circuit batteries or
throw them into water, the general rubbish or in a fire.
Weak batteries can leak and damage the remote control.
Replace them in good time!
REPLACING THE BATTERY
When replacing the battery in the remote control, refer to the
diagram below.
1. Press the catch across.
2. While holding the catch, open the battery door.
a
b
c
d
e
f
g
h
i
Up button
1) Decrease treble button
1! Repeat button
1@ Shuffle button
1# Reset tone button
1$ Decrease bass button
1% Increase bass button
1^ Menu button
3. Fit the battery observing polarity as shown. When
replacing the battery, use only the same CR2025 type
specified.
Source button
Play/pause button
Next button
Enter button
Down button
Volume up button
Increase treble button 1& Previous button
Volume down button 1* Standby button
5
Download from Www.Somanuals.com. All Manuals Search And Download.
iPhone/iPod ADAPTORS
SELECTING AN ADAPTOR
CONNECTING OTHER iPod
MODELS (INC SHUFFLE)
LIST OF SUPPLIED ADAPTORS
(15) iPhone 3G.
has a docking connector. Early iPod models do not have one
and cannot be docked to your unit. The docking connector is
located on the base of the iPod as shown below.
If you own an iPod Shuffle, a model without dock connector
or prefer to connect your iPhone/iPod by cable, you can
connect thesound output to the Audio Input jack on the rear
panel.
(16) iPod touch(2nd generation).
(17) iPod nano(4nd generation).
Other iPhone/iPod models with dock connectors
Your iPhone/iPod may have been supplied, packed with a
standard dock adaptor. If so, this can be used as the docking
bay on your unit is compatible with adaptors supplied by Apple.
Headphone socket
To the Audio
Input jack
If you don’t have a dock adaptor
Docking Connector
If your iPhone/iPod was not supplied with a standard dock
adaptor, you can buy one from Apple on-line. To determine
the exact model of your iPhone/iPod, refer to this web-link -
the iPhone/iPod accessories page on the Apple website to find
an adaptor for your iPhone/iPod model that can be purchased
on-line.
Once you have located the correct adaptor for your iPhone/iPod,
press it gently into the iPhonr/iPod Docking Bay before
attempting to dock your iPhone/iPod.
Before docking your iPhone/iPod, you must first fit the correct
iPhone/iPod adaptor to the docking bay. Each iPone/iPod
adaptor matches the shape of a particular iPhone/iPod and
is necessary to ensure that your iPhone/iPod is securely heid
when docked.
iPhone/iPod adaptor
Docking bay
•
•
Using the 3.5mm stereo jack to jack cable (supplied,
with grey plugs), connect one end of the cable to the
headphone socket of the iPhone/iPod, and the other
end to the Audio Input jack on the back panel.
To listen to your iPhone/iPod, follow the instructions
under ‘External Sources’ on page 8 for playing equipment
connected to the Audio Input jack.
FINDING THE CORRECT iPhone/iPod ADAPTOR
Your iPhone/iPod docking system is supplied with a selection
of docking adaptors that are compatible with several models
in the iPhone/iPod range. Refer to the table of iPhone/iPod
models in the next column which lists the adapeor numbers
(marked underneath the adaptor), compatibility and instructions
for obtaining an adaptor for unlisted models.
NOTE:- The volume control of the iPhone/iPod must be turned
up when playing through the Audio Input jack.
NOTE: Do not dock an iPhone/iPod without fitting the correct
adapotor, you may damage the iPhone/iPod and your unit.
NOTE:- An iPhone/iPod connected to the Audio Input jack
cannot be operated from the remote control.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
DOCKING AN iPhone/iPod
PLAYING FROM AN iPhone/iPod
CONNECTING POWER
DOCKING YOUR iPhone/iPod
To dock your iPhone/iPod:
Playing from a docked iPhone/iPod:
Before connecting the power, check that the mains voltage
on the rating plate of the AC adaptor is the same as the
voltage in your area.
•
Set the iPhone/iPod to play.
You can also operate your iPhone/iPod functions from the
control panel or the remote control.
iPhone/iPod playback functions:
•
•
Set the unit to Standby.
Check that the correct iPhone/iPod adaptor is fitted to the
docking bay (see previous page).
•
Plug the DC cord from the AC adaptor into the DC jack on
the back of the unit.
Press the
button to toggle between Play and Pause
•
Locate the iPhone/iPod on the Docking Connector and
press it gently home.
•
Plug the AC adaptor into the wall socket and switch the
mains power on.
mode at any time.
•
•
Press the or button on the remote control to select
the next or previous track on your iPhone/iPod.
Press the button to scroll through the repeat modes
available on the iPhone/iPod.
The iPhone/iPod is now ready to play.
The unit is now ready for use.
NOTE:- The AC adaptor may become warm during operation
- this is normal.
To remove your iPhone/iPod from the dock:
•
•
•
Set the unit to Standby.
Grip the iPhone/iPod at the sides.
Lift the iPhone/iPod gently from the dock.
The display on the iPhone/iPod will show the repeat mode set.
Press the
POWER CONTROL
•
The display on the iPhone/iPod will show if shuꢀe mode is set.
STANDBY CONTROL
CHARGING AN iPhone/iPod
iPhone/iPod menu functions:
When an iPhone/iPod is docked and playing you can navigate the
menus from the keys on the control panel or remote control.
To turn the docking station on:
When an iPhone/iPod is docked, the iPhone/iPod will begin to
charge automatically.
•
Press the button.
The unit will switch on and the buttons on the top panel will
light.
NOTE:- The iPhone/iPod will charge at all times that the unit is
connected to mains power.
•
•
To move up through the iPhone/iPod menu, pres.s Menu.
To scroll up and down options displayed on the iPhone/iPod
menu, press the or button.
•
Press the button.
•
To select menu items, press the Enter button on the
remote control.
Auto Standby:
The unit will also set to standby automatically, approximately
two minutes after music has finished playing from a docked
iPhone/iPod or a source connected to the Audio Input jack.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE VOLUME
EXTERNAL SOURCES
CHANGING SOURCE
To increase the volume:
The Audio Input jacks on the back panel may be used to
connect sound sources with a Line or Headphone analogue
output to play through your unit. These may include -
SOUND SOURCES
To switch between sound from a docked iPhone/iPod and sound
from an external source:
•
Press the + button on the top panel or the button on
the remote control.
•
•
•
•
•
iPod models that cannot be docked to the unit
MP3 players
CD walkman players
Tape walkman players
Personal computers or laptops
•
Press the button repeatedly to switch between the
two sources.
To decrease the volume:
•
Press the - button on the top panel or the button on the
remote control.
Connecting to the Audio Input jack
•
Connect the Audio Input cable (supplied, with grey plugs)
between the headphone or LINE/AUX output of the
personal audio player and the Audio Input jack on the
back panel.
Playing the external source
•
•
•
Press the button to select the external source.
Set your personal audio player/computer to PLAY.
Set the listening volume to the level you want.
If there is no sound or if the volume level is not loud enough,
you may need to increase the volume setting on your personal
audio player/computer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CONNECTION
VIDEO PLAYBACK
Your docking station includes a video output jack to feed video
signals to a TV from an iPhone/iPod which has video capability.
NOTE:- The TV must have a composite video (CVBS) video
input.
Switching on the iPod video output:
Selecting the correct input on your TV:
Before viewing photo or video programs on your TV you
will need to switch on the iPhone/iPod video output. The
iPhone/iPod video output selector is generally found as follows -
•
Set the TV input selector to the AV input that you used
when connecting the Video cable.
Playing the video:
To connect the docking station to a TV:
•
•
•
•
Navigate to the ‘Videos’ or ‘Photos’ menu of the iPhone/iPod.
Select ‘Settings’.
Select ‘TV out’.
•
Using the remote control, navigate to select the video
you want to watch on the iPhone/iPod display and set it
to play.
•
Connect the video cable (supplied, with yellow plugs) to
the Video Out jack on the back panel.
•
Connect the other end of the cable to a Composite video
(CVBS) input of the TV. A suitable input will often be
Set ‘TV out’to On.
The picture will play on the TV and the sound will play from
your docking station.
The video signal from the iPhone/iPod dock connector will now
be enabled.
video input jack will be coloured yellow.
Typical video connection to a TV
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BASS ANDTREBLE
TROUBLESHOOTING
WARRANTY & SPECIFICATIONS
You can change the equalisation of the sound to suit your
taste by adjusting the bass and treble settings.
No response from the remote control
The remote control battery may be exhausted. Check by
replacing the battery.
SPECIFICATIONS
Supply Voltage, Current :. 12V , 2A
AC Adaptor input:............ 100-240V ~,47-63Hz, 1A
AC Adaptor output: ......... 12 V , 2A
Net Weight:..................... 1.06 kg
To adjust the bass sound:
•
Press the Bass + button repeatedly to boost the bass
sound. You can boost by up to three steps.
No sound/low volume from an external source:
Check that the volume control is turned up on the external
source.
•
Press the Bass - button repeatedly to cut the bass sound.
You can cut by up to three steps.
Class II construction double insulated.
This product must not be connected to earth.
No picture on the TV when playing videos or photos:
Check that the video connections are correctly made.
Check that the correct AV input is selected on the TV.
Check that the iPhone/iPod video output is enabled.
You will hear the change in bass sound as you change the
setting.
To adjust the treble sound:
•
Press the Treble + button repeatedly to boost the treble
sound. You can boost by up to three steps.
UK: Waste electrical products/batteries should
not be disposed of with household waste.
Separate disposal facilities exist, for your near-
in-store for details.
ROI: Produced after 13th August 2005. Waste
electrical products/batteries should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
CARE AND MAINTENANCE
•
Press the Treble - button repeatedly to cut the treble
sound. You can cut by up to three steps.
CARE AND CLEANING
You will hear the change in treble sound as you change the
setting.
All care and cleaning operations should be carried out with
the unit unplugged from the mains power.
The surface of the unit can be cleaned with a barely damp
cloth and then dried carefully. Never use abrasives, abrasive
cloths or chemical solvents .
or treble boost or cut):
•
Press the By Pass
WARRANTY
Your Tesco appliance is covered by a warranty for 12 months
from the date of purchase. If a fault develops during this
period, please contact the TESCO electrical help line on 0845
456 6767. Please have your original purchase receipt with
-
sumer rights.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tesco Stores Ltd, Delamare Road, Cheshunt, Herts, EN8 9SL
SP330 V0.1
UMA0439B
Download from Www.Somanuals.com. All Manuals Search And Download.
|