3.INSTANT mode.
TESTING
TEMPLATE
When an entryis detected. Thealarm sounds
immediately. This is usedto protect youwhen you
are at home.
ALARM OUTPUT AND PANIC BUTTON TEST
MODE S082KA
To test the alarm output, press the PANIC button located on
front of the unit. (THIS UNITIS VERY LOUD, COVER THE
SIREN ON THEFRONT OF THE UNIT BEFOREACTIVATING).
The unit will immediately sound a piercing alarm siren. To
disarm the unit, enter your security code followed by the
#ON/OFF button. (If youhave not entered a security code
4.DELAYmode.
This mode isused when youare leaving yourhome.
On your return, an entry alertbeep tone willsound
to alert youto disarm theunit. If theunit is not
disarmed within10 secondsof entry,the alarm will
sound a110db(S082KA is115db) alarmsiren.
5.The 110db/115db alarmwill sound forabout 30/36
seconds, while thealarm is soundingor during the
entry alert timethe security codecan be enteredto
disarm the unit.
SAFETY SECURITY
MAGNET GUARD
MODEL S082X/S082K
the default is
0
and S082K is
5
CHIME TESTING
1.Set the function switch to the CHIME position.
2.Enter the security code followed by the #ON/OFF button,
the ALARM LED will illuminate. If this does not happen
repeat steps 1 and 2.
6.To disarm theunit, enter thesecurity code followedby
the #ON/OFF button.
CHIME MODE
1.Before activating the chime, slide the function switch
to the CHIME position.
3.Close the door and then open it again, a pleasant chime will
sound 3 times.
4.To disarm the unit, enter the security code followed by the
#ON/OFF button.
5.As long as the unit is in the ARM mode, the chime will
SCREW HOLE
2.Enter the security code followed by the #ON/OFF button.
3.The ARM LED will illuminate to verify the unit is ON,
followed by a short beep. If the ARM light does not
illuminate this indicated the unit is OFF.
4.The chime will sound if there is an entry. The chime will
sound for each entry until the unit is turned OFF(disarmed)
NOTE: The position of the function switch does not
necessarily indicate the mode the unit is in
(CHIME / INSTANT / DELAY). Each time before
activating the unit, set the function switch to the correct
position for the mode desired.
S082KA
1
2
3
continue to sound until DISARMED
.
4
5
#
ALARM TESTING
*
1.Set the function switch to the INSTANT or DELAY
position.
2. Enter the security code followed by the #ON/OFF button,
the ARM LED will turn on. If thisdoes not happen, repeat
steps 1 and 2.
3. Close the door and open it again in INSTANT mode, the
alarm sounds immediately. If thealarm is in DELAY mode,
the alarm will emit a low beep tone to alert your to disarm the
unit, if not disarmed, the unit will then sound a piercing alarm.
4.Todisarm the unit, enter the securitycode followed bythe
#ON/OFF button.
PANIC
PANIC ALARM
SCREW HOLE
SCREW HOLE
S082K
The red PANIC button on the front panel activates the
alarm during a possible emergency.
1.Press the panic button. This will activate the 110db
(S082KA is 115db) alarm siren.
S082X
1
4
7
*
2
5
8
0
3
6
Note: in both modes, CHIME or ALARM (instant / delay) the unit will continue to
sound until DISARMED . The unit will only sound the ALARM if ARMED in
the ALARM mode. If armed in the CHIME mode the unit will sound only the CHIME.
If function switch is changed after the unit has been activated, this will not alter the
sound being produced.
2.Disarm the PANIC alarm, follow the same procedure as
you would to DISARM the unit.
9
#
CAUTION
THE MAGNET GUARD IS EXTREMELY LOUD. FOR YOUR
SAFETY. NEVER PLACE THE UNIT CLOSE TO YOUR EARS.
TO TEST THE ALARM, DIRECT THE UNIT AWAY FROM YOU
AT ARMS LENGTH AND ACTIVATE.
OPERATION
S082X
PATENT PENDING NOTICE
THIS PRODUCT IS PROTECTED UNDER FEDERAL PATENT. TRADEMARK AND COPYRIGHT
LAWS AND LAWS PREVENTING UNFAIR COMPETITION. NO DUPLICATION OR SIMULATION OF
THIS PRODUCT IS PERMITTED EXCEPT BY WRITTEN AUTHORIZATION OF TECHKO, INC.
TECHKO AND THE CONFIGURATION OF THIS PRODUCT ARE TRADEMARKS OF TECHKO, INC.
COPYRIGHT 1992 TECHKO, INC. ALL RIGHTS RESERVED
ALARM MODE
1.Before arming theunit slide thefunction switch tothe
INSTANT/DELAY position.
Customer Service :
1-888-8TECHKO (1-888-883-2456)
2.Toarm the S082X/ S082K, enterthe security code
followed by the #ON/OFF button, the ARM LED will
turn on. Ifthis does nothappen repeat steps1 and 2.
OPERATION MANUL
Mfg. By
9767 Research Drive
Irvine, CA 92618-4626
Download from Www.Somanuals.com. All Manuals Search MAAnDEdINDCHoINwA nload.
|