TEAM PRODUCTS INTERNATIONAL INC. Limited Warranty
WhAT IS COvERED: Any defect in materials and workmanship.
FOR hOW LONg: 2 years from date of purchase.
WhAT WE WILL DO: If your product is defective and returned within 30 days
after the date it was purchased, we will replace it at no charge to you. If
returned after 30 days but within 2 years of the date of purchase we will
repair it or, at our option, replace it at no charge to you.
If we repair your product, we may use new or reconditioned replacement
parts. If we choose to replace your product, we may replace it with a
new or reconditioned one of the same or similar design. The repair or
replacement will be warranted under our standard 2 year warranty.
LIMITATIONS: IMPLIED WARRANTIES, INCLUDINg ThOSE OF FITNESS FOR A
PARTICULAR PURPOSE AND MERChANTAbILITy (AN UNWRITTEN WARRANTy
ThAT ThE PRODUCT IS FIT FOR ORDINARy USE), ARE LIMITED TO 2 yEARS
FROM DATE OF PURChASE. WE WILL NOT PAy FOR LOSS OF TIME, INCONvE-
NIENCE, LOSS OF USE OF yOUR PRODUCT OR PROPERTy DAMAgE CAUSED
by yOUR PRODUCT OR ITS FAILURE TO WORk, OR ANy OThER INCIDENTAL
OR CONSEqUENTIAL DAMAgES INCLUDINg PERSONAL INjURy.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages,
so the above exclusions or limitations may not apply to you.
18 Volt
Cordless Drills
WhAT WE ASk yOU TO DO: To get warranty service for your product,
you must provide proof of the date of purchase. Within 30 days of the
date it was purchased, return your product to your place of purchase for
immediate replacement. After 30 days, but before the end of the 2 year
warranty period, you may return the product to the following address:
Team Products International
Attn: Customer Service Returns
Owner’s Manual
35 A Continental Drive
Wayne, Nj 07470
We suggest that you retain your original packing material in the event
you need to ship your product. When sending your product include your
name, address, phone number, proof of date of purchase, and a
description of the operating problem. After repairing or replacing your
product, we will ship it to your home or office within four weeks.
WhAT ThIS WARRANTy DOES NOT COvER: Among oTher ThIngS ThIS
WArrAnTy doeS noT cover defecTS reSulTIng from AccIdenTS,
dAmAge WhIle In TrAnSIT To our ServIce locATIon, AlTerATIonS,
unAuThorIzed repAIr, fAIlure To folloW InSTrucTIonS, mISuSe, fIre,
flood, And AcTS of god. If your producT IS noT covered by our
WArrAnTy, cAll our cuSTomer ServIce number AT (888) 231-4022 To
deTermIne WheTher We WIll repAIr your producT And oTher repAIr
InformATIon, IncludIng chArgeS. We, AT our opTIon, mAy replAce
rATher ThAn repAIr your producT WITh A neW or recondITIoned
one of The SAme or SImIlAr deSIgn. The repAIr or replAcemenT WIll
be WArrAnTed for 2 yeArS.
Models: PMD8137
PMD8142
PMD8143
ThIS lImITed WArrAnTy IS The only one We gIve on your producT,
And IT SeTS forTh All our reSponSIbIlITIeS regArdIng your producT.
There Are no WArrAnTIeS WhIch exTend beyond The deScrIpTIon SeT
forTh Above.
©2006 The Coleman Company, Inc. All rights reserved.
STATE LAW RIghTS: This warranty gives you specific legal rights and you
may also have other rights which may vary from state to state.
COLEMAN® and
are registered trademarks of The Coleman Company, Inc., used under license.
Designed in the USA and custom-manufactured in China for Team Products International Inc.
Distributed by Team Products International Inc., Mountain Lakes, NJ 07046.
PMD8137DR020306 -222
Download from Www.Somanuals.com. All Manuals Search And Download.
Models: PMD8137
PMD8142
Owner’s Manual
PMD8143
Welcome
15. Remove adjustment keys and wrenches. Form a habit to make sure
thatt the adjustment keys and wrenches are removed from the tools before
turning them ON.
This COLEMAN® product has been carefully engineered and manufactured to
give you dependable operation. Please read this manual thoroughly before
operating your new COLEMAN® product, as it contains the information you
need to become familiar with its features and obtain the performance that will
bring you continued enjoyment for many years. Please keep this manual on file
for future reference.
16. Stay alert. To avoid injury pay attention to the work you are doing when
operating these power tools.
17. Check damaged parts. Before continuing to use any power tool, check
for damaged parts to determine that it will operate properly and perform
its intended function. Check alignment of moving parts, mounting of parts,
breakage of parts and anything else that may affect its operation. A part
that has been damaged or broken must be properly repaired or replaced by
an authorized service technician unless otherwise indicated in this manual.
Have damaged ON/OFF switches replaced by a qualified service technician.
Do not use a tool that will not turn OFF or ON.
GENERAL OPERATING INSTRUCTIONS WHEN USING ANY BATTERY
OPERATEDTOOL.
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS PRIOR
TO USING ANY POWERTOOLS. FAILURETO DO SO MAY RESULT IN
ELECTRIC SHOCK, FIRE AND/OR SERIOUS PERSONAL INJURY.
1. SAVETHESE INSTRUCTIONS FOR FUTURE REFERENCE.
18. Keep hands clear of moving parts.
2. Keep work area clean. Cluttered work areas and workbenches may cause
19. Do not touch moving parts. Allow the power tool accessories (bit and
blades etc.) to cool before touching them.They can become extremely hot
during use and can burn your skin.
injury.
3. Be conscious of the work area. Do not use the power tools in damp or
moist areas. Do not expose power tools to rain. Do not use these tools in the
presence of flammable liquids or gases.
20. READ ALL INSTRUCTIONS BEFORE USINGTHESE POWERTOOLS.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER:
4. Keep work area well lit.
1.This manual includes important safety instructions for the battery charger.
Fully read all instructions and warning labels before using the battery or bat-
tery charger.
5. Keep out of reach of children.
6. Store idle tools. Remove the batteries and store tools in a dry place when
not in use.
2.To reduce the risk of electric shock or injury, use ONLY the battery charger
supplied with this unit to charge the battery(ies).
7. Do not force tools. Forcing the tools can cause damage to the unit or
serious injury.
3. Do NOT expose the battery or battery charger to rain or moisture.
8. Use the right tool for the right job. Use power tools for the purpose
4. Use of any attachment not recommended in this manual may result in the risk
of fire, electric shock or injury to person and will void the warranty.
intended.
9. Dress properly. Do not wear loose clothing or dangling jewelry when
operating any power tool as they can be caught in moving parts. Rubber
gloves and nonskid footwear are recommended when working outdoors.
Keep longer hair pulled back.
5.To reduce the risk of damaging the battery charger power cord, be sure to
pull the plug rather then the cord when disconnecting it from the power
supply. Always position the cord so it will not be stepped on or tripped over.
This will prevent damage to the cord.
10. Always wear protective safety glasses when operating power
6. An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord can result in risk of fire or electric shock. If using an
extension cord make sure that:
tools. Wear a facemask when environment is dusty.
11. Secure items being worked on. Use a vice or clamp to securely hold the
item you are working on. Do not use your hands.
A)The pins on the plug of the extension cord are the same number,
size and shape as those on the plug on the charger.
12. Never overreach. Keep proper footing and balance at all times.
B)The extension cord is properly wired and in good working condition.
C)The wire size is the same or larger than the ones specified below:
13. Maintain tools. Keep tool blades sharp and keep tools clean for better and
safer performance. Inspect batteries before using them with the tools. Keep
hands dry and free from grease and oil when operating these power tools.
14. Disconnect tools. Remove the batteries from the tools before changing
bits and blades.This will prevent unintentional use.
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Models: PMD8137
PMD8142
Owner’s Manual
PMD8143
Controls and Components:
Battery and AC Charger
1. Battery with Release Buttons On Each Side (PMD8137 comes with 2 batteries)
2. 1 Hour “Quick Charge” Charging Stand with LED Charging Indicators
Recommended size of Extension Cord for Battery Charger
Length of Cord (Feet)
AWG Size of Cord*
25
18
50
18
100
16
150
14
Drill:
3. 3/8” Jacobs Keyless Chuck
4. 24 AdjustableTorque Settings Control Ring
5. Forward/Lock/Reverse Switch
6. High/Low Speed Switch
7. Variable SpeedTrigger Switch
*The smaller the AWG (American Wire Gauge) number of the extension cord,
the higher the capacity of the cable for conducting current to ensure proper
usage of the tool.
7. Do not operate charger with a damaged cord or plug.
1
8. Accessory/Bit Holder
9. RUBBERSUIT™
(entire drill body is covered with
smooth rubberized paint)
8. Do not operate the charger if it has received a sharp blow, been dropped or
damaged in any other way.
9. Do not open the drill, battery or battery charger.There are no user serviceable
parts. Opening the unit will void the warranty.
Accessories:
10. 6 Various Screwdriver Bits
11. 2” Extension Bar
10. Unplug the charger from its power source when not in use.
2
12. 2 Double Ended Screwdriver Bits
11. Do not touch the terminals inside the battery charger with any other metal
object such as nails or coins.This can short the charger.
13. 6 Various Drill Bits
9
6
5
12. Do not store the unit in areas where the temperature can exceed 120°F.
4
13. Do not throw the battery or battery charger in fire.This can cause an
explosion.
3
14. WARINING: Batteries vent hydrogen gas and may explode in the presence
of a source of ignition, such as a pilot light. To reduce the risk of serious
personal injury, never use any cordless product in the presence of an open
flame. An exploded battery can propel debris and chemicals. If exposed,
flush with water immediately for a minimum of 10 minutes and seek
medical attention.
7
8
1
13
15. During extreme conditions, the battery may leak. This does not indicate a
battery failure. However, if the liquid gets on your skin, immediately wash
with soap and water, neutralize the area with a mild acid such as lemon
juice or vinegar. If the liquid gets into your eyes, flush them with clean
water immediately for a minimum of 10 minutes and seek medical
attention.
11
12
10
INSTRUCTIONS FOR USE:
ChargingThe Battery
THE BATTERY(IES) MAY NOT BE FULLY CHARGED FROM THE
FACTORY. READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO FIRST
USE.
The Drills covered by this manual use the same battery and battery charger.
Your Drill comes complete with a rechargeable battery, which we recommend
that you fully charge before the first use.
Drill must be charged for 1 hour prior to first use. After initial charge, allow
approximately 1 hour to recharge your battery.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Models: PMD8137
PMD8142
Owner’s Manual
PMD8143
Twist the 24 setting torque control ring to the desired setting. Lower settings are
better for light work such as driving screws into soft materials. Higher settings
are recommended for drilling into harder surfaces.
The battery should be recharged when the drill does not operate up to its
normal performance level. Do not continue to operate the drill in this depleted
capacity. Recharge the battery immediately.
When properly adjusted, the clutch will slip at
its present torque setting to prevent driving
the screw too deep or to prevent damage to
the tool.
To increase the life of your battery, do not leave the battery charging for more
than 1 hour. While this is not a safety concern, overcharging may reduce the life
of the battery(ies).
Overtime, if drill is not used, the battery will lose capacity. For maximum
performance recharge the battery after prolonged storage or non-use periods.
To operate the drill in forward setting, sim-
ply keep the Forward/Lock/Reverse switch
flat against the side of the drill as shown.To
NOTE: Before inserting or removing the battery from the charging base, always
ensure that the base is not plugged into a 120V power source.
change to reverse setting, move the Forward/
Lock/Reverse switch until it is flat against the
1.To begin charging, remove the battery pack from the tool by pressing on the
battery release buttons on either side of the battery pack and pulling down.
opposite side of the drill. Keeping the Forward/Lock/Reverse switch in the center
position locks the drill and prevents unintentional use. It is recommended that
the Drill is in the locked position when it is not in use or is being stored.
2. Plug the battery pack into the battery charger making sure the positive (+) and
negative (-) poles of the battery match the positive (+) and negative (-) poles
of the battery charger.
CAUTION: Always check the direction of the rotation before using the drill.
The speed of the drill is increased by the amount of pressure you place on the
ON/OFF trigger switch.The less pressure you put on the trigger switch, the
slower the drill will go.
NOTE:The battery will only fit into the battery charger and the tool one way.
3. Plug the battery charger into any standard 120 Volt wall outlet.The RED LED
indicator on the battery charger will illuminate to indicate that the battery is
charging.
Your drill comes with an automatic braking function that quickly stops the chuck
from turning when the trigger switch is released.
4. Full charging will take 1 hour.
Your drill has two speed ranges; low speed (position 1) (0-400 rpm) and high
speed (position 2 ) (0-1100 rpm).
NOTE: While the battery is placed in the charger, the RED LED indicator light
will remain on. After one hour and a complete charge, the GREEN LED indicator
light will illuminate to let you know it is now safe to use the battery.
Screwdriver Operation
If charging more than one battery, wait at least 15 minutes between each
charge.
Place the point of the screwdriver bit into the head of
the screw and apply slight pressure to the tool. Press
the trigger switch slightly and then gradually increase
the drill speed. Release the trigger switch as soon as
the clutch engages. Note: Starting the drill at too high
of a speed can damage the drill bit or reduce the life
of the bit.
Use only the battery charger that is supplied with this tool. Using another
charger may cause damage to the battery.
WARNING: Never charge a battery pack again imme-
diately after it has been fully charged.This can give rise
to the battery pack being overcharged and a reduced
battery life.
Make sure that the driver bit is inserted straight in
the screw head or the screw may become damaged
or will not be inserted properly. When driving wood
screws, pre-drill pilot holes into the surface to make driving easier.This will also
prevent the wood from splitting.
UsingThe Drill
CAUTION: Always make sure that the tool is switched
OFF and the battery pack is removed from the drill
before changing any bits. Loosen the keyless chuck by
holding the ring and turning the sleeve counter
clockwise. Select the drill bit or screwdriver you want to
use and place it in the keyless chuck.Twist the sleeve of
the keyless chuck clockwise to tighten it, making sure the
drill bit remains in the center of the keyless chuck’s teeth.
Note: When drilling, the drill bit can become stuck. When this happens a very
high torque will be produced. Always take care to hold the drill firmly to prevent
possible damage or injury.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Models: PMD8137
PMD8142
Owner’s Manual
PMD8143
Maintenance
Clean the drill regularly. Before cleaning, remove the battery pack and any
accessories (bits etc.).To clean, use ONLY a mild soap and damp cloth on the
housing. Never immerse drill in any kind of fluid. Do not use any solvents or
harsh abrasives on the drill housing as this may cause damage to the unit.
Always keep the ventilation openings clear.
NOTE: All bearings in these tools are lubricated with a sufficient amount of
high-grade lubricant for the life of the unit under normal operating conditions.
No further lubrications required.
CAUTION: DO NOT keep the trigger switch pressed in with tape or any other
permanent means or the circuit will not function properly. A malfunction may
result possibly causing overheating or damage to the unit.
Do not open the drill, battery or battery charger.There are no user serviceable
parts. Opening the unit will void the warranty.
TROUBLESHOOTINGTIPS:
DRILL DOES NOT WORK?
• Recharge the battery
CHARGING INDICATOR LED NOT ILLUMINATED DURING RECHARGING?
• Check that battery pack is properly connected to the battery charger
• Check that the AC Adaptor is properly connected at both ends
SPECIFICATIONS
Voltage
18V
Speed 1
0-400RPM
0-1100RPM
24 + Drill
Speed 2
Torque Settings
Chuck Capacity
Charger Input
ChargingTime
BatteryType
up to 3/8”
120V AC 60Hz
Approx. 1 Hour
Ni-Cad
QUESTIONS?
If you have any questions about this product, please contact our Customer
Service Department at (888) 231-4022, 9 am to 5 pm EST, Monday through
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|