Taylor Refrigerator C713 User Manual

OPERATOR'S

MANUAL

Model C713

Soft Serve Freezer

Original Operating Instructions

062180-M

2/11/05 (Original Publication)

(Updated 8/26/14)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Section 1

To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Water Connections (Water Cooled Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 2

To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 3

Section 4

Model C713 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model C713 Door and Beater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section 5

Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operating Screen Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Manager's Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Section 6

Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Freezing Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Manual Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Draining Product From The Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Model C713

Table of Contents

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents - Page 2

Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Hopper Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Section 7

Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Section 8

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Section 9

Section 10

Section 11

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Note: Continuing research results in steady improvements; therefore, information

in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation

representative(s) are considered to be the original set of instructions.

E 2005 Carrier Commercial Refrigeration, Inc. (Original Publication)

(Updated August, 2014)

062180- M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work

may be a violation of Copyright Law of the United States of America and other countries, could result in the

awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Table of Contents

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 1

To the Installer

The following information has been included in the

manual as safety and regulatory guidelines. For

complete installation instructions, please see the

Installation Checklist.

This unit has many sharp edges that can

cause severe injuries.

Site Preparation

Installer Safety

Review the area the unit is to be installed in before

uncrating the unit making sure that all possible

hazards the user or equipment may come into have

been addressed.

In all areas of the world, equipment should

be installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Air Cooled Units

The Model C713 air cooled unit requires a minimum

of 3” (76 mm) of clearance on all sides. Install the

deflector provided to prevent recirculation of warm

air. This will allow for adequate air flow across the

condenser. Failure to allow adequate clearance can

reduce the refrigeration capacity of the freezer and

possibly cause permanent damage to the

compressor.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

service of Taylor equipment.

Only authorized Taylor service personnel

should perform installation and repairs on

the equipment.

For Indoor Use Only: This unit is designed to

operate indoors, under normal ambient

temperatures of 70_-75_F (21_-24_C). The freezer

has successfully performed in high ambient

temperatures of 104_(40_C) at reduced capacities.

Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the

industry standards on lockout/tagout

procedures before beginning any installation

or repairs.

Authorized service personnel must ensure

that the proper PPE is available and worn

when required during installation and

service.

This unit must NOT be installed in an area

where a water jet or hose can be used. NEVER use

a water jet or hose to rinse or clean the unit. Failure

to follow this instruction may result in electrocution.

Authorized service personnel must remove

all metal jewelry, rings, and watches before

working on electrical equipment.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should

be taken in moving this equipment for any reason.

Two or more persons are required to safely move

this unit. Failure to comply may result in personal

injury or equipment damage.

The main power supply(s) to the freezer

must be disconnected prior to performing any

repairs. Failure to follow this instruction may result in

personal injury or death from electrical shock or

hazardous moving parts as well as poor

Uncrate the unit and inspect it for damage. Report

any damage to your Taylor Distributor.

performance or damage to the equipment.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

Note: All repairs must be performed by an

authorized Taylor Service Technician.

131121

Model C713

To the Installer

Download from Www.Somanuals.com. All Manuals Search And Download.

Water Connections

(Water Cooled Units Only)

CAUTION: THIS EQUIPMENT MUST BE

PROPERLY GROUNDED! FAILURE TO DO SO

CAN RESULT IN SEVERE PERSONAL INJURY

FROM ELECTRICAL SHOCK!

An adequate cold water supply must be provided

with a hand shut-off valve. On the underside of the

base pan or on the right side, two 3/8” I.P.S. water

connections for inlet and outlet are provided for easy

hook-up. 1/2” inside diameter water lines should be

connected to the machine. (Flexible lines are

recommended, if local codes permit.) Depending on

local water conditions, it may be advisable to install

a water strainer to prevent foreign substances from

clogging the automatic water valve. There will be

only one water “in” and one water “out” connection.

DO NOT install a hand shut-off valve on the water

“out” line! Water should always flow in this order:

first, through the automatic water valve; second,

through the condenser; and third, through the outlet

fitting to an open trap drain.

DO NOT operate this freezer with larger

fuses than specified on the unit data label. Failure to

follow this instruction may result in electrocution or

damage to the machine.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the

rear of the frame by the authorized installer. The

installation location is marked by the equipotential

bonding symbol (5021 of IEC 60417-1) on both the

removable panel and the equipments frame.

A back flow prevention device is

required on the incoming water connection side.

Please refer to the applicable National, State, and

local codes for determining the proper configuration.

Stationary appliances which are not

equipped with a power cord and a plug or another

device to disconnect the appliance from the power

source must have an all-pole disconnecting device

with a contact gap of at least 3mm installed in the

external installation.

Electrical Connections

In the United States, this equipment is intended to

be installed in accordance with the National

Electrical Code (NEC), ANSI/NFPA 70-1987. The

purpose of the NEC code is the practical

safeguarding of persons and property from hazards

arising from the use of electricity. This code contains

provisions considered necessary for safety. In all

other areas of the world, equipment should be

installed in accordance with the existing local codes.

Please contact your local authorities.

Appliances that are permanently connected

to fixed wiring and for which leakage currents may

exceed 10 mA, particularly when disconnected or

not used for long periods, or during initial installation,

shall have protective devices such as a GFI, to

protect against the leakage of current, installed by

the authorized personnel to the local codes.

Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not lighter than

ordinary polychloroprene or other equivalent

synthetic elastomer-sheathed cord (Code

FOLLOW YOUR LOCAL ELECTRICAL CODES!

designation 60245 IEC 57) installed with the proper

cord anchorage to relieve conductors from strain,

including twisting, at the terminals and protect the

insulation of the conductors from abrasion.

Each unit requires one power supply for each data

label on the unit. Check the data label(s) on the

freezer for branch circuit overcurrent protection or

fuse, circuit ampacity, and other electrical

specifications. Refer to the wiring diagram provided

inside of the electrical box for proper power

connections.

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent, or similarly

qualified person, in order to avoid a hazard.

130318

To the Installer

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Beater Rotation

Use only R404A refrigerant that conforms

to the AHRI standard 700 specification. The use of

any other refrigerant may expose users and

operators to unexpected safety hazards.

Beater rotation must be clockwise as viewed

looking into the freezing cylinder.

Note: The following procedures should be performed

by a trained service technician.

To correct the rotation on a three-phase unit,

interchange any two incoming power supply lines at

freezer main terminal block only.

Refrigerant liquid sprayed onto the skin may

cause serious damage to tissue. Keep eyes and skin

protected. If refrigerant burns should occur, flush

immediately with cold water. If burns are severe,

apply ice packs and contact a physician

immediately.

To correct rotation on a single-phase unit, change

the leads inside the beater motor. (Follow the

diagram printed on the motor.)

Electrical connections are made directly to the

terminal block provided in the splice box.

Taylor reminds technicians to be cautious of

government laws regarding refrigerant recovery,

recycling, and reclaiming systems. If you have any

questions regarding these laws, please contact the

factory Service Department.

Refrigerant

In consideration of our environment, Taylor

proudly uses only earth friendly HFC refrigerants.

The HFC refrigerant used in this unit is R404A. This

refrigerant is generally considered non-toxic and

non-flammable, with an Ozone Depleting Potential

(ODP) of zero (0).

WARNING: R404A refrigerant used in

conjunction with polyolester oils is extremely

moisture absorbent. When opening a refrigeration

system, the maximum time the system is open must

not exceed 15 minutes. Cap all open tubing to

prevent humid air or water from being absorbed by

the oil.

However, any gas under pressure is potentially

hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with

liquid. Filling the cylinder to approximately 80% will

allow for normal expansion.

130930

Model C713

To the Installer

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 2

To the Operator

Your freezer has been carefully engineered and

manufactured to give you dependable operation.

similar legislation in effect after August 13, 2005.

Therefore, it must be collected separately after its

use is completed, and cannot be disposed as

unsorted municipal waste.

This unit, when properly operated and cared for, will

produce a consistent quality product. Like all

mechanical products, it will require cleaning and

maintenance. A minimum amount of care and

attention is necessary if the operating procedures

outlined in this manual are followed closely.

The user is responsible for returning the product to

the appropriate collection facility, as specified by

your local code.

For additional information regarding applicable local

laws, please contact the municipal facility and/or

local distributor.

This Operator's Manual should be read before

operating or performing any maintenance on your

equipment.

Compressor Warranty Disclaimer

Your Taylor freezer will NOT eventually compensate

for and correct any errors during the set-up or filling

operations. Thus, the initial assembly and priming

procedures are of extreme importance. It is strongly

recommended that personnel responsible for the

equipment's operation, both assembly and

disassembly, go through these procedures together

in order to be properly trained and to make sure that

no confusion exists.

The refrigeration compressor(s) on this unit are

warranted for the term stated in the Limited

Warranty section in this manual. However, due to

the Montreal Protocol and the U.S. Clean Air Act

Amendments of 1990, many new refrigerants are

being tested and developed, thus seeking their way

into the service industry. Some of these new

refrigerants are being advertised as drop-in

replacements for numerous applications. It should

be noted that in the event of ordinary service to this

unit's refrigeration system, only the refrigerant

specified on the affixed data label should be

used. The unauthorized use of alternate refrigerants

will void your Taylor compressor warranty. It is the

unit owner's responsibility to make this fact known to

any technician he employs.

In the event you should require technical assistance,

please contact your local authorized Taylor

Distributor.

Note: Your Taylor warranty is valid only if the parts

are authorized Taylor parts, purchased from the

local authorized Taylor Distributor, and only if all

required service work is provided by an authorized

Taylor service technician. Taylor reserves the right

to deny warranty claims on units or parts if

non-Taylor approved parts or incorrect refrigerant

were installed in the unit, system modifications were

performed beyond factory recommendations, or it is

determined that the failure was caused by abuse,

misuse, neglect, or failure to follow all operating

instructions. For full details of your Taylor Warranty,

please see the Limited Warranty section in this

manual.

It should also be noted that Taylor does not warrant

the refrigerant used in its equipment. For example, if

the refrigerant is lost during the course of ordinary

service to this machine, Taylor has no obligation to

either supply or provide its replacement either at

billable or unbillable terms. Taylor does have the

obligation to recommend a suitable replacement if

the original refrigerant is banned, obsoleted, or no

longer available during the five year warranty of the

compressor.

Taylor will continue to monitor the industry and test

new alternates as they are being developed. Should

a new alternate prove, through our testing, that it

would be accepted as a drop-in replacement, then

the above disclaimer would become null and void.

To find out the current status of an alternate

refrigerant as it relates to your compressor warranty,

call the local Taylor Distributor or the Taylor Factory.

Be prepared to provide the Model/Serial Number of

the unit in question.

Note: Constant research results in steady

improvements; therefore, information in this

manual is subject to change without notice.

If the crossed out wheeled bin symbol is

affixed to this product, it signifies that this product is

compliant with the EU Directive as well as other

131121

To the Operator

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 3

Safety

We, at Taylor Company, are concerned about the

safety of the operator when he or she comes in

contact with the freezer and its parts. Taylor has

gone to extreme efforts to design and manufacture

built-in safety features to protect both you and the

service technician. As an example, warning labels

have been attached to the freezer to further point

out safety precautions to the operator.

DO NOT operate the freezer unless it is

properly grounded.

DO NOT operate freezer with larger fuses

than specified on the data label.

All repairs must be performed by an

authorized Taylor service technician.

The main power supplies to the machine

must be disconnected prior to performing

any repairs.

To Operate Safely:

For Cord Connected Units: Only Taylor

authorized service technicians or licensed

electricians may install a plug or

IMPORTANT - Failure to adhere to the

following safety precautions may result in

severe personal injury or death. Failure to

comply with these warnings may damage the

machine and its components. Component

damage will result in part replacement expense

and service repair expense.

replacement cord on these units.

Stationary appliances which are not

equipped with a power cord and a plug or

another device to disconnect the appliance

from the power source must have an all-pole

disconnecting device with a contact gap of

at least 3 mm installed in the external

installation.

Appliances that are permanently connected

to fixed wiring and for which leakage

currents may exceed 10 mA, particularly

when disconnected or not used for long

periods, or during initial installation, shall

have protective devices such as a GFI, to

protect against the leakage of current,

installed by the authorized personnel to the

local codes.

DO NOT operate the freezer without

reading this Operator Manual. Failure to follow this

instruction may result in equipment damage, poor

freezer performance, health hazards, or personal

injury.

Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not

lighter than ordinary polychloroprene or

other equivalent synthetic

elastomer-sheathed cord (Code designation

60245 IEC 57) installed with the proper cord

anchorage to relieve conductors from strain,

including twisting, at the terminals and

protect the insulation of the conductors from

abrasion.

This appliance is to be used only by trained

personnel. It is not intended for use by children or

people with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge,

unless given supervision or instruction concerning

the use of the appliance by a person responsible for

their safety. Children should be supervised to ensure

that they do not play with the appliance.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent, or similarly qualified person, in order

to avoid a hazard.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the

rear of the frame by the authorized installer. The

installation location is marked by the equipotential

bonding symbol (5021 of IEC 60417-1) on both the

removable panel and the equipments frame.

Failure to follow these instructions may result in

electrocution. Contact your local authorized Taylor

Distributor for service.

130213

Model C713

Safety

Download from Www.Somanuals.com. All Manuals Search And Download.

DO NOT use a water jet to clean or rinse

the freezer. Failure to follow these instructions may

result in serious electrical shock.

This freezer must be placed on a level

surface. Failure to comply may result in personal

injury or equipment damage.

Cleaning and sanitizing schedules are

governed by your state or local regulatory agencies

and must be followed accordingly. Please refer to

the cleaning section of this manual for the proper

procedure to clean this unit.

DO NOT allow untrained personnel to

operate this machine.

DO NOT operate the freezer unless all

service panels and access doors are

restrained with screws.

DO NOT remove any internal operating

parts (examples: freezer door, beater,

scraper blades, etc.) unless all control

switches are in the OFF position.

This machine is designed to maintain

product temperature under 41°F (5°C). Any product

being added to this machine must be below 41°F

(5°C). Failure to follow this instruction may result in

health hazards and poor freezer performance.

Failure to follow these instructions may result in

severe personal injury to fingers or hands from

hazardous moving parts.

DO NOT obstruct air intake and discharge openings:

This unit has many sharp edges that can

cause severe injuries.

A minimum of 3” (76 mm) air space is required on all

sides. Install the deflector provided to prevent

recirculation of warm air. Failure to follow this

instruction may cause poor freezer performance and

damage to the machine.

DO NOT put objects or fingers in the door

spout. This may contaminate the product

and cause severe personal injury from blade

contact.

USE EXTREME CAUTION when removing

the beater asssembly. The scraper blades

are very sharp.

For Indoor Use Only: This unit is designed to

operate indoors, under normal ambient

temperatures of 70_ - 75_F (21_ - 24_C). The

freezer has successfully performed in high ambient

temperatures of 104_(40_C) at reduced capacities.

CAUTION-SHARP EDGES: Two people are

required to handle the cup/cone dispenser.

Protective gloves must be worn and the

mounting holes must NOT be used to lift or

hold the dispenser. Failure to follow this

instruction can result in personal injury to

fingers or equipment damage.

DO NOT run the machine without product. Failure to

follow this instruction can result in damage to the

machine.

Access to the service area of the unit is

NOISE LEVEL: Airborne noise emission does not

exceed 78 dB(A) when measured at a distance of

1.0 meter from the surface of the machine and at a

height of 1.6 meters from the floor.

restricted to persons having knowledge and practical

experience with the appliance, in particular as far as

safety and hygiene are concerned.

130318

Safety

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes:

Model C713

Safety

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 4

Operator Parts Identification

Model C713

Figure 1

121005

Operator Parts Identification

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

C713 Exploded View Parts Identification

ITEM

DESCRIPTION

COVER-HOPPER

PART NO.

ITEM

DESCRIPTION

PART NO.

053809-1

022465-100

016137

SCREW-1/4-20 X 3/8 RHM-SS

011694

063087

ORIFICE

PANEL-CORNER-FRONT

RIGHT

O-RING-3/8 OD X ..070 W

TUBE A.-FEED-SS 5/32 HOLE

O-RING-.643 OD X .077 W

PANEL-REAR

CASTER-4” SWV 3/4-10 STEM

W/BRAKE

046437

X29429-2

018572

DEFLECTOR-BLOWER

047912

059917

SHIELD-SPLASH-WIRE-19-3/4 L 033813

PANEL-SIDE*RIGHT

PAN-DRIP 12.5

059907

PANEL A.-FRONT LOWER

TRAY-DRIP-19-5/8 L X 4-7/8

PAN-DRIP 19-1/2 LONG

X59854-SER

059736

033812

035034

PANEL A.-FRONT

X63879

X59836

055987

PANEL A.-FRONT

PANEL-CORNER-FRONT LEFT 063088

STUD-NOSE CONE

FILTER-AIR-POLY-FLO

PANEL A.-FILTER-LOUVERED

CASTER-4” SWV 3/4-10 STEM

PANEL-SIDE LEFT

059906

030787

030788

052779-11

X59928

044106

FASTENER-DOOR LATCH

FASTENER-DOOR STRIKE

121005

Model C713

Operator Parts Identification

Download from Www.Somanuals.com. All Manuals Search And Download.

Model C713 Door and Beater Assembly

Figure 2

ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

HANDLE A.-DRAW-WELDED

O-RING-1/4 OD X .070W 50

SCREW-ADJUSTMENT-5/16-24

PLUG-PRIME TWIN

X56421-1

015872

056332

059936

024278

CAP-DESIGN 1.010" ID - 6 PT

SEAL-DRAW VALVE

014218

034698

014402

059894

O-RING-7/8 OD X .103 W

PIN-HANDLE-TWIN

O-RING-1/2 OD X 0.70 W

GASKET-DOOR HT 4"-DOUBLE 048926

BEARING-FRONT 050216

BLADE-SCRAPER-PLASTIC 17L 035174

NUT-STUD-BLACK 3.250 LONG 058765

NUT-STUD-BLACK 2.563 LONG 058764

DOOR A.-3SPT*LG BAF*W/PRG X59922

BEATER A.-3.4QT-HELICORE

SHAFT-BEATER

X31761

032564

032560

VALVE A.-DRAW

X59843

X62218

VALVE A.-DRAW CENTER

SEAL-DRIVE SHAFT

081008

Operator Parts Identification

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Figure 3

ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

LUBRICANT-TAYLOR

TOOL-O-RING REMOVAL

PAIL-10 QT

047518

SANITIZER-STERA SHEEN

KIT A.-TUNE-UP

SEE NOTE

X49463-80

048260-WHT

013163

Not Shown

Note: A sample container of sanitizer is sent with the

unit. For reorders, order Stera Sheen part no. 055492

(100 2 oz. packs) or Kay-5 part no. 041082 (200 packs).

140721

Model C713

Operator Parts Identification

Download from Www.Somanuals.com. All Manuals Search And Download.

Brushes

Figure 4

ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

BLACK BRISTLE BRUSH

DOUBLE END BRUSH

013071

013072

013073

BRUSH-END-DOOR SPOUT SS 039719

BRUSH-SET LVB

050103

054068

WHITE BRISTLE BRUSH

(1” x 2”)

BRUSH-PUMP SPOUT

WHITE BRISTLE BRUSH

(3” x 7”)

023316

Operator Parts Identification

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 5

Important: To the Operator

Figure 5

ITEM

DESCRIPTION

ITEM

DESCRIPTION

POWER SWITCH

LIQUID CRYSTAL DISPLAY

KEYPADS

SELECT KEY

SERVICE MENU KEY

BRUSH CLEAN COUNTER

ARROW KEYS

MIX OUT INDICATOR

STANDBY KEY

TOPPING HEATER KEYS

MIX LOW INDICATOR

130213

Model C713

Important: To the Operator

Download from Www.Somanuals.com. All Manuals Search And Download.

Symbol Definitions

= TOPPING HEATER-LEFT

= TOPPING HEATER-RIGHT

To better communicate in the International arena,

symbols have replaced words on many of our

operator switches, function, and fault indicators.

Your Taylor equipment is designed with these

International symbols.

Power Switch

The following chart identifies the symbol definitions.

When placed in the ON position, the power switch

allows control panel operation.

= SELECT

Fluorescent Display

The fluorescent display is located on the front

control panel. During normal operation the display is

blank. The display is used to show menu options

and notifies the operator if a fault is detected. On

International models, the display will indicate the

temperature of the mix in the hopper.

= ON

= OFF

Indicator Lights

MIX LOW - When the MIX LOW symbol

illuminated, the mix hopper has a low supply of mix

and should be refilled as soon as possible.

= UP ARROW

= DOWN ARROW

= AUTO

MIX OUT - When the MIX OUT

symbol is

illuminated, the mix hopper has been almost

completely exhausted and has an insufficient supply

of mix to operate the freezer. At this time, the AUTO

mode is locked out and the freezer will be placed in

the STANDBY mode. To initiate the refrigeration

system, add mix to the mix hopper and touch the

AUTO symbol . The freezer will automatically

begin operation.

= WASH

Standby Symbol

= MIX LOW

= MIX OUT

= MENU DISPLAY

= STANDBY

During long “No Sale” periods, the unit can be

placed into the Standby mode. This maintains

product temperatures below 40°F (4.4°C) in both the

hopper and the freezing cylinder, and helps prevent

overbeating and product breakdown.

Using clean, sanitized hands, remove the air orifice.

Lubricate the o-rings located on the end of the feed

tube without the hole. Place that end of the tube into

the mix inlet hole. When STANDBY is selected, the

STANDBY symbol

illuminates, indicating the

Standby feature has been activated.

IMPORTANT: Make sure the level of mix in the

hopper is below the mix inlet hole in the feed

130626

Important: To the Operator

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

tube. Failure to follow this instruction may result in

lower product quality when normal operation is

resumed.

Feed Tube

The feed tube serves two purposes. One end of the

tube has a hole and the other end does not. The air

orifice maintains overrun and allows enough mix to

enter the freezing cylinder after a draw.

To resume normal operation, press the AUTO

symbol . When the unit cycles off, the product in

the freezing cylinder will be at serving viscosity. At

this time, turn the feed over. Place the end of the

tube with the hole into the mix inlet hole. Install the

air orifice.

Wash Symbol

The WASH symbol

will illuminate when it is

touched. This indicates beater motor operation. The

STANDBY or AUTO modes must be cancelled first

to activate the WASH mode.

Auto Symbol

Figure 6

1. Normal Operation

The AUTO symbol

will illuminate when it is

During normal operation, the end of the feed

tube with the hole is placed into the mix inlet

hole. Every time the draw handle is raised, new

mix and air from the hopper flow into the

freezing cylinder. This keeps the freezing

cylinder properly loaded and maintains overrun.

touched. This indicates that the refrigeration system

has been activated. In the AUTO mode, the WASH

or STANDBY functions are automatically cancelled.

Note: An indicating light and an audible tone will

sound whenever a mode of operation has been

selected. To cancel any function, touch the key

again. The light and the mode of operation will shut

off.

2. Long “No Sale” Periods

During long “No Sale” periods, the unit can be

placed into the Standby mode. This maintains

product temperatures below 40°F (4.4°C) in

both the hopper and the freezing cylinder, and

helps prevent overbeating and product

breakdown. To activate STANDBY, enter the

access code for the Manager Menu (see

page 17.) Remove the air orifice. Lubricate the

o-rings located on the end of the feed tube

without the hole. Place that end of the tube into

the mix inlet hole.

Reset Mechanism

The reset buttons are located in the back panel of

the machine. It protects the beater motor from an

overload condition. Should an overload occur, the

reset mechanism will trip. To properly reset the

freezer place the power switch in the OFF position.

Press the reset button firmly. Turn the power switch

to the ON position. Touch the WASH symbol

observe the freezer's performance.

and

IMPORTANT: Make sure the level of mix in

the hopper is below the mix inlet hole in the

feed tube. Failure to follow this instruction may

result in lower product quality when normal

operation is resumed.

WARNING: Do not use metal objects

to press the resetbutton. Failure to comply may

result in severe personal injury or death.

To resume normal operation, press the AUTO

symbol . When the unit cycles off, the

product in the freezing cylinder will be at

serving viscosity. At this time, turn the feed

over. Place the end of the tube with the hole

into the mix inlet hole. Install the air orifice. The

air orifice is used to meter a certain amount of

air into the freezing cylinder.

If the beater motor is turning properly, touch the

WASH symbol

to cancel the cycle. Touch the

AUTO symbol

to resume normal operation. If the

freezer shuts down again, contact your authorized

service technician.

130626

Model C713

Important: To the Operator

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjustable Draw Handle

NVRAM FAULT

RESET TO DEFAULTS

PRESS SEL KEY

This unit features an adjustable draw handle to

provide the best portion control, giving a better,

consistent quality to your product and controlling

costs. The draw handle should be adjusted to

provide a flow rate of 5 to 7-1/2 oz. (142 to 213 g.)

of product by weight per 10 seconds. To INCREASE

the flow rate, tighten the screw. To DECREASE the

flow rate, loosen the screw. (See Figure 7.)

Figure 8

See “NVRAM FAULT” for instructions if the above

message appears on the screen.

Once the system has initialized, the number of days

remaining before the next required brush cleaning is

indicated on the control panel and the SAFETY

TIMEOUT screen is displayed with the alarm turned

on. (See Figure 9.)

SAFETY TIMEOUT

ANY KEY ABORTS

Figure 9

The SAFETY TIMEOUT screen will be displayed

with the alarm on, for 60 seconds or until any control

symbol is selected.

Figure 7

After the safety timeout has been completed and the

power switch is OFF, the following screen is

displayed. (See Figure 10.)

Operating Screen Descriptions

POWER SWITCH OFF

- = - = - = - = - = -

The fluorescent display located in the center of the

control panel is normally blank during the daily

operation of the machine. The display is activated

when the SEL symbol or the Manager's Menu is

selected. The display screen will also alert the

operator of specific faults detected by the control.

UNIT CLEANED

Figure 10

Power Switch ON

Power Up

When the power switch is placed in the ON position,

the control panel touch keys become operative. The

fluorescent display will be either blank or indicate

that the unit has been cleaned. (See Figure 11.)

When the machine is powered the control system

will initialize to perform a system check. The screen

will display “INITIALIZING”. There will be four types

of data the system will check: LANGUAGE,

SYSTEM DATA, CONFIG DATA, and LOCKOUT

DATA.

During the INITIALIZING... LANGUAGE screen, the

alarm will be on. If the system detects corrupt data

during INITIALIZING, the following display will alert

the operator that the control settings may have been

changed (See Figure 8.)

UNIT CLEANED

Figure 11

Important: To the Operator

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Brush Clean Counter

Entering Access Code

The Brush Clean Counter (item 9 on page 13) will

display the number of hours since the freezer was

last brush cleaned. After hour 99, it will change to a

letter and a number (example: A0, A1. . B0, B1, etc.)

With the ACCESS CODE screen on the display use

the SEL symbol to set the first code number in the

cursor position. When the correct number is

selected, touch the SEL symbol to move the cursor

to the next number position. (See Figure 13.)

Manager's Menu

The Manager's Menu is used to enter the operator

function displays. To access the Menu, touch the

ENTER ACCESS CODE

center of the CONE symbol

The arrow symbols, the SEL symbol and the CONE

on the control panel.

symbol will be lit when the ACCESS CODE

screen is displayed. (See Figure 12.)

Figure 13

Continue to enter the proper access code numbers

(8309) until all four numbers are displayed, then

touch the SEL symbol. The Manager's menu list will

display on the screen provided the correct access

code is entered.

If an incorrect number is entered for the access

code, the display will exit the Menu program when

the SEL symbol is selected. (See Figure 14.)

Figure 12

In the Menu program, the arrow symbols and the

SEL symbol will function as menu keys.

UP ARROW - increases the value above the cursor

and is used to scroll upward in text displays.

DOWN ARROW - decreases the value above the

cursor and is used to scroll downward in text

displays.

SEL - advances the cursor position to the right and

is used to select menu options.

Note: The machine will continue operation in the

mode it was in when the menu was selected.

However, the control keys will not be lit and are

non-functional when the Manager's Menu is

displayed.

Figure 14

Model C713

Important: To the Operator

Download from Www.Somanuals.com. All Manuals Search And Download.

Reset the SERVING COUNTER by selecting the

SEL symbol to advance to the next screen. Select

the UP arrow symbol to move the arrow (>) to YES

and select the SEL symbol. The servings counter

will reset to zero and exit back to the Manager's

Menu. (See Figure 16.)

Menu Options

Touch the ARROW symbols to move up or down

through the Menu. Select a Menu option by touching

the SEL symbol. Exit the Menu program by selecting

EXIT FROM MENU or touch the CONE symbol

RESET DRAW COUNTER

YES

The following menu options are listed in the

Manager's Menu.

EXIT FROM MENU

RESET DRAW COUNTER

SET CLOCK

Figure 16

The SET CLOCK option allows the Manager to

adjust the control clock date and time. The date and

time may only be changed after the freezer has

been manually cleaned but before it has been

placed in the AUTO or STANDBY mode. The

following message will be displayed if the SET

CLOCK option is selected when the machine is not

in a brush clean state. (See Figure 17.)

AUTO START TIME

STANDBY MODE

MIX LEVEL AUDIBLE

LOCKOUT HISTORY

SYSTEM INFORMATION

SET CLOCK

12:01

7/15/2004

Selecting “EXIT FROM MENU” will exit the

Manager's Menu and the return the control panel

symbols to normal operation.

NO CHANGES ALLOWED

Press Any Key

The SERVING COUNTER screen is used to check

or reset the number of servings dispensed from the

machine. The SERVING COUNTER will

automatically reset to zero when the machine is

brush cleaned. (See Figure 15.)

Figure 17

To change the date or time, select the SET CLOCK

option in the menu. Touch the UP arrow symbol to

advance the arrow from Exit to Change, then touch

the SEL symbol to select the Change option.

(See Figure 18.)

SERVINGS COUNTER

SET CLOCK

12:01

Change

> Exit

7/15/2004

> Next

Figure 15

Figure 18

050722

Important: To the Operator

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Change the time by touching the UP arrow with the

cursor under the hour position. Move the cursor to

the minutes by touching the SEL symbol. Once the

correct minutes are entered, touch the SEL symbol

to advance the cursor to the month. (See Figure 19.)

Enable the AUTO START TIME by selecting the UP

arrow symbol to move the arrow up to Enable.

Touch the SEL symbol to advance to the next

screen. (See Figure 22.)

AUTO START TIME

00:00

SET CLOCK

12:01

Change

Exit

7/15/2004

> Exit

Figure 22

Figure 19

Program the AUTO START TIME by selecting the

UP arrow symbol to move the arrow to Change.

Touch the SEL symbol to advance to the next

screen. (See Figure 23.)

Enter the correct month, day, and year. Then touch

the SEL symbol to advance to the DAYLIGHT

SAVING TIME screen. (See Figure 20.)

AUTO START TIME

00:00

DAYLIGHT SAVING TIME

ENABLED

Enable

Disable

Figure 23

Figure 20

Use the arrow symbols to program the AUTO

START TIME by increasing or decreasing the hour

setting above the cursor. Touch the SEL symbol to

advance the cursor and program the minutes

setting. Select the SEL symbol to return to the

previous screen with the new time setting displayed.

Select the SEL symbol to exit the screen and return

to the Menu.

The Daylight Saving feature when enabled, will

automatically adjust the control clock for daylight

saving time. To Disable the Daylight Saving Time

feature, select the UP arrow to move the arrow to

Disable. Then touch the SEL symbol to save the

new setting.

The STANDBY option is used to manually place

either side of the machine in the Standby mode

during long, no draw periods. Select the STANDBY

screen from the Menu. Touch the SEL symbol to

activate Standby.

The AUTO START TIME option allows the Manager

to set the time of day at which the machine

automatically enters the AUTO mode from the

STANDBY mode. The machine must be in the

STANDBY mode in order to AUTO start at the

programmable time. The AUTO START TIME can

also be disabled and require starting the AUTO

mode manually. (See Figure 21.)

Discontinue Standby operation by exiting the

Manager's Menu and select the AUTO mode.

(See Figure 24.)

AUTO START TIME

DISABLED

STANDBY MODE

Enable

Disable

EXIT

Figure 21

Figure 24

Model C713

Important: To the Operator

Download from Www.Somanuals.com. All Manuals Search And Download.

The MIX LEVEL AUDIBLE option, when enabled,

will alert the operator with an audible tone when

there is mix low or mix out condition. The following

screen is displayed upon selecting this option.

(See Figure 25.)

Faults Occurring While in AUTO Mode

HPR>41F (5C) AFTER 4 HR - The mix temperature

in the hopper was above 41_F (5_C) more than four

hours.

MIX LEVEL AUDIBLE

BRL>41F (5C) AFTER 4 HR - The mix temperature

in the freezing cylinder was above 41_F (5_C) more

than four hours.

Enable

Disable

HPR>41F (5C) AFTER PF - The mix temperature in

the hopper was above 41_F (5_C) more than four

hours following a power failure.

Figure 25

Disable the audible tone feature by selecting the UP

arrow symbol to move the arrow to Disable. Select

the SEL symbol to save the new setting and return

to the Menu. The control panel icons for Mix Low

and Mix Out will light as the mix level drops in the

hopper but the audible tone will be disabled.

BRL>41F (5C) AFTER PF - The mix temperature in

the freezing cylinder was above 41_F (5_C) more

than four hours following a power failure.

HPR>45F (7C) AFTER 1 HR - The mix temperature

in the hopper was above 45_F (7_C) more than one

hour.

The LOCKOUT HISTORY screen displays a history

of the faults. (See Figure 26.)

BRL>45F (7C) AFTER 1 HR - The mix temperature

in the freezing cylinder was above 45_F (7_C) more

than one hour.

LOCKOUT HISTORY

07/27/04

12:58

HPR>59F (15C) - The mix temperature in the

hopper exceeded 59_F (15_C).

HPR THERM FAIL

EXIT

BRL>59F (15C) - The mix temperature in the

freezing cylinder exceeded 59_F (15_C).

Figure 26

Use the arrow symbols to advance forward or

backward to view each screen. The following list

indicates the variable messages that may appear.

Note: Refer to your local health codes regarding

temperature recommendations for procedures to

follow if these fault screens appear.

Important: To the Operator

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

The SYSTEM INFORMATION is displayed on three

separate screens. The first screen contains the

control and software version installed in the

machine. (See Figure 27.)

Touch the SEL symbol to advance to the third

system information screen containing the model bill

of material and machine serial number. Touching the

SEL symbol again will return to the Menu list.

(See Figure 29.)

SOFTWARE VERSION

C713 CONTROL UVC3

VERSION 1.04

B.O.M. C71333C000

S/N

K0000000

> Next

Figure 27

Touch the SEL symbol to advance to the next

system information screen containing the software

language version. (See Figure 28.)

Figure 29

Language

V1.11 r 00 English 515

> Next

Figure 28

Model C713

Important: To the Operator

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 6

Operating Procedures

The C713 machine stores mix in the hoppers. It has

two 3.4 quart (3.2 liter) capacity freezing cylinders

with a three spout door. Mix flows by gravity through

a feed tube down into the freezing cylinders.

Step 3

Heavily lubricate the inside portion of the boot seal

and also lubricate the flat end of the boot seal that

comes in contact with the rear shell bearing.

Step 4

We begin our instructions at the point where we

enter the store in the morning and find the parts

disassembled and laid out to air dry from the

previous night's cleaning.

Apply an even coat of lubricant to the shaft. DO

NOT lubricate the hex end.

These opening procedures will show you how to

assemble these parts into the freezer, sanitize them,

and prime the freezer with fresh mix in preparation

to serve your first portion.

If you are disassembling the machine for the first

time or need information to get to this starting point

in our instructions, turn to page 30, “Disassembly”,

and start there.

Figure 30

Freezing Cylinder Assembly

Note: To ensure the mix does not leak out of the

back of the freezing cylinder, the middle section of

the boot seal should be convex or extend out from

the seal. If the middle section of the boot seal is

concave or extending into the middle of the seal,

turn the seal inside out.

Note: When lubricating parts, use an approved food

grade lubricant (example: Taylor Lube).

MAKE SURE THE POWER SWITCH IS IN

THE “OFF” POSITION! Failure to follow this

instruction may result in severe personal injury from

hazardous moving parts.

Step 1

Before installing the beater drive shaft, lubricate the

groove on the beater drive shaft.

Step 2

Slide the beater drive shaft boot seal over the small

end of the beater drive shaft and engage into the

groove on the shaft.

Figure 31

110107

Operating Procedures

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 5

Step 7

Insert the beater drive shaft through the rear shell

bearing in the freezing cylinder and engage the hex

end firmly into the drive coupling.

Holding the beater securely, slide the beater into the

freezing cylinder about one-third of the way in.

Looking into the freezing cylinder, align the hole at

the rear of the beater with the flats on the end of the

drive shaft.

Figure 32

USE EXTREME CAUTION when handling

the beater assembly. The scraper blades are very

sharp and may cause injury.

Figure 34

Step 6

Step 8

Before installing the beater assembly, check the

scraper blades. If they are in good condition, take

one of the scraper blades and slip it under the hook

at the front of the beater. Wrap the blade around the

beater, following the helix and pushing the blade

down onto the helix as you wrap. At the back end of

the beater, slip the blade under the hook.

Slide the beater the remainder of the way into the

freezing cylinder and over the end of the drive shaft.

The beater should fit snugly but not so tightly that

the beater cannot be turned slightly to engage the

drive shaft.

Make sure the beater assembly is in position over

the drive shaft. Turn the beater slightly to be certain

that the beater is properly seated. When in position,

the beater will not protrude beyond the front of the

freezing cylinder.

Step 9

Repeat these steps for the other side of the

machine.

Step 10

To assemble the freezer door, place the door

gaskets into the grooves on the back of the freezer

door. Slide the front bearings over the baffle rods.

The flanged edges should be against the door. DO

NOT lubricate the gaskets or bearings.

Figure 33

Repeat this step for the second scraper blade.

Model C713

Operating Procedures

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 11

Step 13

Slide the two o-rings into the grooves on each prime

plug. Apply an even coat of Taylor Lube to the

o-rings and shafts.

To install the freezer door, insert the baffle rods

through the beaters in the freezing cylinders.

Figure 37

Figure 35

With the door seated on the freezer studs, install the

handscrews. Use the long handscrews on the top

and the short handscrews on the bottom. Tighten

them equally in a criss-cross pattern to insure the

door is snug.

Step 12

Insert the prime plugs into the holes in the top of the

freezer door and push down.

Figure 36

Figure 38

Operating Procedures

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 14

Step 16

Slide the three o-rings into the grooves of each

standard draw valve. Slide the H-ring and o-ring into

the grooves of the center draw valve. Lubricate the

H-ring and o-rings.

Insert the draw valves from the bottom until the slot

in the draw valves come into view.

Figure 41

Step 17

Slide the fork of the draw handles in the slot of the

draw valves, starting from the right.

Figure 39

Step 15

Lubricate the inside of the freezer door spouts, top

and bottom.

Figure 42

Step 18

Slide the pivot pin through each draw handle as they

are inserted into the draw valves.

Figure 40

Figure 43

Model C713

Operating Procedures

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: This freezer features three adjustable draw

handles to provide portion control, giving a better

consistent quality to your product and controlling

costs. The draw handle should be adjusted to

provide a flow rate of 5 to 7-1/2 oz. (142 g. to

213 g.) of product by weight per 10 seconds.

Step 21

Install the front drip tray and splash shield under the

door spouts.

To INCREASE the flow rate, turn the adjustment

screw CLOCKWISE. Turn the adjustment screw

COUNTER-CLOCKWISE to DECREASE the flow

rate.

Step 19

Snap the design caps over the bottom of the door

spouts.

Figure 46

Step 22

Slide two o-rings on one end of the feed tube. Slide

two o-rings on the other end of the feed tube.

Figure 44

Step 20

Figure 47

Slide the two drip pans into the holes in the side

panels.

Step 23

Slide the small o-ring into the groove of the air

orifice. Do not lubricate the o-ring.

Figure 45

Figure 48

Operating Procedures

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: Make sure the hole in the air orifice is clean

and is not clogged. If the hole in the air orifice should

become clogged, use soap and hot water to clear

the hole. Do not enlarge the hole in the air

orifice.

Step 24

Install the air orifice into the hole in the top of the

feed tube (end without the small hole on the side).

Figure 50

Note: You have just sanitized the mix hopper and

parts; therefore, be sure your hands are clean and

sanitized before going on in these instructions.

Step 3

While the solution is flowing into the freezing

cylinder, take particular care to brush-clean the mix

level sensing probe on the bottom of the hopper, the

mix hopper, the mix inlet hole, and the mix feed

tube.

Figure 49

Step 25

Lay the feed tube (with the air orifice installed) in the

bottom of the mix hopper for sanitizing.

Step 26

Repeat steps 22 through 25 for the other side of

the machine.

Sanitizing

Step 1

Prepare an approved 100 PPM sanitizing solution

(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2

gal. [7.6 liters] of Stera-SheenR). USE WARM

WATER AND FOLLOW THE MANUFACTURER'S

SPECIFICATIONS.

Figure 51

Step 4

Prepare another pail of approved 100 PPM sanitiz-

ing solution (examples: 2-1/2 gal. [9.5 liters] of

Kay-5R or 2 gal. [7.6 liters] of Stera-SheenR).

USE WARM WATER AND FOLLOW THE MANU-

FACTURER'S SPECIFICATIONS.

Step 2

Pour the sanitizing solution over all the parts in the

bottom of the mix hopper and allow it to flow into the

freezing cylinder.

Model C713

Operating Procedures

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 5

Priming

Pour the sanitizing solution into the mix hopper.

Step 6

Brush the exposed sides of the hopper.

Note: Use only FRESH MIX when priming the

freezer.

Step 7

Place the power switch in the ON position.

Step 1

Step 8

Place an empty pail beneath the door spouts. With

the prime plug in the UP position, pour 2-1/2 gallons

(9.5 liters) of FRESH mix into the mix hopper and

allow it to flow into the freezing cylinder.

Touch the WASH symbol . This will cause the

sanitizing solution in the freezing cylinder to be

agitated. Wait at least 5 minutes before proceeding

with these instructions.

Step 2

Step 9

Open the draw valve to remove all sanitizing

solution. When only fresh mix is flowing, close the

draw valve.

With an empty pail beneath the door spouts, raise

the prime plug.

Step 10

Step 3

When a steady stream of sanitizing solution is

flowing from the prime plug opening in the bottom of

the freezer door, open the draw valve. Momentarily

open the center draw valve to sanitize the center

door spout. Draw off the remaining sanitizing

solution.

Once a steady stream of mix starts to flow from the

prime plug opening in the bottom of the freezer door,

push the prime plug down.

Step 4

When mix stops bubbling down into the freezing

cylinder, install the end of the feed tube with the

hole in it into the mix inlet hole in the mix hopper.

Make sure the air orifice is installed in the feed tube.

Step 11

Once the sanitizer stops flowing from the door

spout, touch the WASH symbol

draw valve.

and close the

Step 5

Note: Be sure your hands are clean and

Select the AUTO symbol

sanitized before going on in these instructions.

Step 12

Step 6

Lubricate the feed tube o-rings on the end with the

small hole on the side. Stand the feed tube in the

corner of the hopper.

Fill the hopper with fresh mix and place the mix

hopper cover in position.

Step 13

Step 7

Repeat these steps for the other side of the

machine.

Repeat these steps for the other side of the

machine.

140721

Operating Procedures

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Brush Cleaning

Rinsing

Step 1

ALWAYS FOLLOW LOCAL HEALTH CODES.

Pour two gallons (7.6 liters) of cool, clean water into

the mix hopper. With the white hopper brush, scrub

the mix hopper and the mix level sensing probe.

Using the double ended brush, brush clean the mix

inlet hole.

To disassemble the Model C713, the following items

will be needed:

Two cleaning and sanitizing pails

Sanitizer/Cleaner

Necessary brushes (provided with freezer)

Single service towels

Draining Product From The

Freezing Cylinder

Step 1

Remove the hopper cover and the feed tube. Take

them to the sink for cleaning.

Step 2

Figure 52

With a pail beneath the door spouts, touch the

WASH symbol

and open the draw valve.

Note: Do not brush clean the mix inlet hole while

the machine is in the WASH mode.

Step 3

If local health codes permit the use of rerun,

place a sanitized, NSF approved stainless steel

rerun container beneath the door spout. Press the

WASH key and open the draw valve. Drain the

remaining product from the freezing cylinder and mix

hopper. When the flow of product stops, press the

WASH key and close the draw valve. Place the

sanitized lid on the rerun container and place it in

the walk-in cooler.

Step 2

With a pail beneath the door spout, raise the prime

plug and touch the WASH symbol

Step 3

When a steady stream of rinse water is flowing from

the prime plug opening in the bottom of the freezer

door, open the draw valve. Drain all the rinse water

from the door spout. Close the draw valve, and

Note: If local health codes DO NOT permit the

use of rerun, the product must be discarded.

Follow the instructions in the previous step, except

drain the product into a pail and properly discard the

mix.

touch the WASH symbol,

mode.

cancelling the Wash

Step 4

Repeat this procedure using clean, warm water until

the water being discharged is clear.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Repeat these steps for the other side of the

machine.

Repeat these steps for the other side of the

machine.

140721

Model C713

Operating Procedures

Download from Www.Somanuals.com. All Manuals Search And Download.

Hopper Cleaning

Disassembly

Step 1

Place the power switch in the OFF position.

Note: Failure to follow these steps will result in

milk-stone build-up.

Step 2

Remove the handscrews, freezer door, beater and

scraper blades, and drive shaft with drive shaft seal

from the freezing cylinder.

Step 1

Prepare an approved 100 PPM cleaning solution

(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2

gal. [7.6 liters] of Stera-SheenR). USE WARM

WATER AND FOLLOW THE MANUFACTURER'S

SPECIFICATIONS.

Step 3

Remove the scraper blades from the beater

assembly.

Step 4

Step 2

Remove the drive shaft seal from the drive shaft.

Push the prime plug down. Pour the cleaning

solution into the hopper and allow it to flow into the

freezing cylinder.

Step 5

Remove the freezer door gasket, front bearing, pivot

pin, draw handle, draw valve, prime plugs and

design caps. Remove the three o-rings from the

draw valve.

Step 3

Using the white hopper brush, clean the mix hopper

and the mix level sensing probes. Using the double

ended brush, clean the mix inlet hole.

Repeat these steps on the other side of the

machine.

Note: Do not brush clean the mix inlet hole while

the machine is in the WASH mode.

Step 6

Remove the front drip tray and splash shield.

Step 4

Step 7

Touch the WASH symbol . This will cause the

cleaning solution in the freezing cylinder to come in

contact with all areas of the freezing cylinder.

Remove all drip pans. Take them to the sink for

cleaning.

Step 5

Place an empty pail beneath the door spouts and

raise the prime plug.

Step 6

When a steady stream of cleaning solution is flowing

from the prime plug opening in the bottom of the

freezer door, open the draw valve. Draw off all the

solution.

Step 7

Once the cleaning solution stops flowing from the

door spout, close the draw valve and touch the

Figure 53

WASH symbol , cancelling the Wash mode.

Note: If the drip pans are filled with an excessive

amount of mix, it is an indication that the drive shaft

seal(s), or o-ring(s) should be replaced or properly

lubricated.

Repeat these steps on the other side of the

machine.

Operating Procedures

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Brush Cleaning

Step 1

Prepare an approved 100 PPM cleaning solution

(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2

gal. [7.6 liters] of Stera-SheenR). USE WARM

WATER AND FOLLOW THE MANUFACTURER'S

SPECIFICATIONS. Make sure all brushes provided

with the freezer are available for brush cleaning.

Step 2

Thoroughly brush clean all disassembled parts in the

cleaning solution, making sure all lubricant and mix

film is removed. Be sure to brush all surfaces and

holes, especially the holes in the freezer door.

Figure 54

Step 3

Rinse all parts with clean, warm water. Place the

parts on a clean, dry surface to air dry overnight.

Repeat these steps on the other side of the

machine.

Step 4

Return to the freezer with a small amount of

cleaning solution. Using the black brush, clean the

rear shell bearing at the back of the freezing

cylinder.

Step 5

Wipe all exterior surfaces of the freezer with a clean,

sanitized towel.

Model C713

Operating Procedures

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 7

Important: Operator Checklist

j 5. IF LOCAL HEALTH CODES PERMIT THE

During Cleaning and Sanitizing

USE OF RERUN, make sure the mix rerun is

stored in a sanitized, covered, NSF approved

stainless steel rerun container and used the

following day. DO NOT prime the machine

with rerun. When using rerun, skim off the

foam and discard; then mix the rerun with

fresh mix in a ratio of 50/50 during the day's

operation.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Cleaning and sanitizing schedules are governed

by federal, state, or local regulatory agencies,

and must be followed accordingly. If the unit

has a “Standby mode”, it must not be used in

lieu of proper cleaning and sanitizing

procedures and frequencies set forth by the

ruling health authority. The following check

points should be stressed during the cleaning

and sanitizing operations.

j 6. On a designated day of the week, run the mix

as low as feasible and discard it after closing.

This will break the rerun cycle and reduce the

possibility of high bacteria and coliform

counts.

j 7. Properly prepare the cleaning and sanitizing

solutions. Read and follow the label directions

carefully. Too strong of a solution may

damage the parts and too weak of a solution

will not do an adequate job of cleaning or

sanitizing.

j 8. The temperature of the mix in the mix hopper

and walk-in cooler should be below 40_F

(4.4_C).

Troubleshooting Bacterial Count

j 1. Thoroughly clean and sanitize the machine

regularly, including complete disassembly and

brush cleaning.

Regular Maintenance Checks

j 2. Use all brushes supplied for thorough

cleaning. The brushes are specially designed

to reach all mix passageways.

j 1. Replace scraper blades that are nicked or

damaged. Before installing the beater

assembly, be certain that scraper blades are

properly attached to the helix.

j 3. Use the white bristle brush to clean the mix

inlet hole which extends from the mix hopper

down to the rear of the freezing cylinder.

j 2. Check the rear shell bearing for signs of wear

(excessive mix leakage in rear drip pan) and

be certain it is properly cleaned.

j 4. Use the black bristle brush to thoroughly

clean the rear shell bearing located at the rear

of the freezing cylinder. Be sure there is a

generous amount of cleaning solution on the

brush.

j 3. Using a screwdriver and cloth towel, keep the

rear shell bearing and the female hex drive

socket clean and free of lubricant and mix

deposits.

120210

Important: Operator Checklist

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

j 4. Dispose of o-rings and seals if they are worn,

torn, or fit too loosely, and replace with new

ones.

Winter Storage

If the place of business is to be closed during the

winter months, it is important to protect the freezer

by following certain precautions, particularly if the

building is subject to freezing conditions.

j 5. Follow all lubricating procedures as outlined in

“Assembly”.

j 6. If your machine is air cooled, check the

condensers for accumulation of dirt and lint.

Dirty condensers will reduce the efficiency

and capacity of the machine. Condensers

should be cleaned monthly with a soft brush.

Never use screwdrivers or other metal probes

to clean between the fins.

Disconnect the freezer from the main power source

to prevent possible electrical damage.

On water cooled freezers, disconnect the water

supply. Relieve pressure on the spring in the water

valve. Use air pressure on the outlet side to blow out

any water remaining in the condenser. This is

extremely important. Failure to follow this

procedure may cause severe and costly damage to

the refrigeration system.

Note: For machines equipped with an air

filter, it will be necessary to vacuum clean the

filters on a monthly schedule.

Your local Taylor Distributor can perform this winter

storage service for you.

Caution: Always disconnect

electrical power prior to cleaning the

condenser. Failure to follow this instruction

may result in electrocution.

Wrap detachable parts of the freezer such as

beater, blades, drive shaft, and freezer door, and

place them in a protected dry place. Rubber trim

parts and gaskets can be protected by wrapping

them with moisture-proof paper. All parts should be

thoroughly cleaned of dried mix or lubrication which

attract mice and other vermin.

j 7. If your machine is water cooled, check the

water lines for kinks or leaks. Kinks can occur

when the machine is moved back and forth for

cleaning or maintenance purposes.

Deteriorated or cracked water lines should be

replaced only by an authorized Taylor

distributor.

It is recommended that an authorized service

technician perform winter storage draining, to insure

all water has been removed. This will guard against

freezing and rupturing of the components.

Model C713

Important: Operator Checklist

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 8

Troubleshooting Guide

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

1. No product is being

dispensed.

a. Low on mix. The MIX

OUT light is on.

a. Add mix to the mix

hopper. Return to AUTO

mode.

b. The power switch is in the

OFF position.

b. Place the power switch to

ON and select AUTO.

c. Machine not in AUTO

mode.

c. Select AUTO and allow

machine to cycle off

before drawing product.

- - -

d. Beater motor is out on

reset. The BEATER

OVERLOAD message

displayed.

d. Turn the machine off.

Press the reset button.

Restart the machine in

AUTO.

- - -

e. Freeze-up in mix inlet

hole.

e. Call an authorized service

technician.

f. Feed tube is not properly

installed.

f. Make sure feed tube is

properly installed.

2. The product is too soft.

3. The product is too thick.

a. Draw rate is set too fast.

a. Adjust draw rate of 5 to 7

1/2 oz. (142 g. to 213 g.)

of product by weight in 10

seconds.

- - -

a. Freezing cylinder not

primed correctly.

a. Drain the freezing cylinder

and reprime the machine.

b. The viscosity control is set b. Call an authorized service

technician.

too cold.

c. Freeze-up in mix inlet

hole.

c. Call an authorized service

technician.

Important: Operator Checklist

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

4. The mix in the hopper is

too warm.

a. Hopper cover is not in

position.

a. Clean and sanitize hopper

cover and place in

position.

- - -

b. The hopper temperature is b. Call an authorized service

technician.

out of adjustment.

a. The hopper temperature is a. Call an authorized service

5. The mix in the hopper is

too cold.

technician.

out of adjustment.

6. Mix Low and Mix Out

probes are not

a. Milkstone build-up in the

hopper.

a. Clean hoppers thoroughly.

functioning.

7. Product is collecting on

top of the freezer door.

a. The top o-ring on draw

valve is improperly

a. Lubricate properly or

replace the o-ring.

lubricated or worn.

8. Excessive mix leakage

from the bottom of door

spout.

a. Bottom o-ring on draw

valve is improperly

a. Lubricate properly or

replace the o-ring.

lubricated or worn.

9. Excessive mix leakage

into the long drip pan.

a. The seal on drive shaft is

improperly lubricated or

worn.

a. Lubricate properly or

replace the seal.

b. The seal is installed

inside-out on the drive

shaft.

b. Install correctly.

- - -

c. Inadequate lubrication of

the drive shaft.

c. Lubricate properly.

d. The drive shaft and beater d. Call an authorized service

technician.

assembly work forward.

e. Worn rear shell bearing.

e. Call an authorized service

technician.

f. Gear box out of alignment.

f. Call an authorized service

technician.

10. The drive shaft is stuck in

the drive coupling.

a. Mix and lubricant collected a. Brush clean the rear shell

bearing area regularly.

in drive coupling.

- - -

b. Rounded corners of drive

shaft, drive coupling, or

both.

b. Call an authorized service

technician.

- - -

c. Gear box is out of

alignment.

c. Call an authorized service

technician.

Model C713

Important: Operator Checklist

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

11. The freezing cylinder

walls are scored.

a. Missing or worn front

bearing.

a. Install or replace the front

bearing.

b. Broken freezer door baffle

rod.

b. Replace freezer door.

c. Beater assembly is bent.

c. Replace beater assembly.

- - -

d. Gear box is out of

alignment.

d. Call an authorized service

technician.

12. The product makes a

popping sound when

drawn.

a. Draw rate is set too fast.

a. Adjust draw rate of 5 to 7

1/2 oz. (142 g. to 213 g.)

of product by weight in 10

seconds.

b. Freezing cylinder not

primed correctly.

b. Drain the freezing cylinder

and reprime the machine.

- - -

13. No control panel functions

with power switch ON.

a. Machine is unplugged.

a. Plug into wall receptacle.

b. Circuit breaker OFF or

blown fuse.

b. Turn the breaker ON or

replace the fuse.

Important: Operator Checklist

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 9

Parts Replacement Schedule

PART DESCRIPTION

EVERY 3 MONTHS

EVERY 6 MONTHS

ANNUALLY

Scraper Blade

Drive Shaft Seal

Freezer Door Gasket

Front Bearing

Draw Valve O-Ring

Draw Valve Seal

Prime Plug O-Ring

Mix Feed Tube O-Ring

Design Cap

White Bristle Brush, 3” x 7”

Inspect & Replace

if Necessary

Minimum

White Bristle Brush, 1” x 2”

Inspect & Replace

if Necessary

Black Bristle Brush, 1” x 2”

Double-Ended Brush

Inspect & Replace

if Necessary

Minimum

Inspect & Replace

if Necessary

Model C713

Parts Replacement Schedule

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 10 Limited Warranty on Equipment

TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited

warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)

to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and

service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to

defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,

will provide a new or re-manufactured part, at Taylor’s option, to replace the failed defective part at no charge for

the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty

for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed

below and on the reverse (if any) of this document.

Product

Soft Serve

Part

Limited Warranty Period

Five (5) years

Insulated shell assembly

Frozen Yogurt

Shakes

Refrigeration compressor

(except service valve)

Five (5) years

Beater motors

Two (2) years

Smoothies

Frozen Beverage

Batch Desserts

Beater drive gear

Printed circuit boards and

Softech controls beginning

with serial number H8024200

Parts not otherwise listed in

this table or excluded below

One (1) year

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins

ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of

purchase may be required at time of service.

2. This limited warranty is valid only if the Product is installed and all required service work on the Product is

performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are

used.

3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in

the Taylor Operator’s Manual.

4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.

5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of

defective parts, replacement parts, or new Products.

2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning

of condensers.

131121

Limited Warranty on Equipment

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.

4. External hoses, electrical power supplies, and machine grounding.

5. Parts not supplied or designated by Taylor, or damages resulting from their use.

6. Return trips or waiting time required because a service technician is prevented from beginning warranty

service work promptly upon arrival.

7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,

unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including

but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning

supplies.

8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake

or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,

accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or

water supply specification of the Product; or components repaired or altered in any way so as, in the

judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.

9. Any Product purchased over the Internet.

10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the

inadequacy or interruption of electrical service.

11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will

void this limited warranty.

13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY

NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from

jurisdiction to jurisdiction.

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE

REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE

COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL

OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,

PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS

WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED

BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or

complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other

correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or

remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072, U.S.A.

Model C713

Limited Warranty on Equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

Section 11

Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS

Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited

warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally

(the “Parts”) to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service

as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails

due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service

agency, will provide a new or re-manufactured Part, at Taylor’s option, to replace the failed defective Part at no

charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited

warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions

listed below and on the reverse (if any) of this document.

Part's Warranty Class Code or Part

Class 103 Parts¹

Limited Warranty Period

Three (3) months

Class 212 Parts²

Twelve (12) months

No warranty

Class 512 Parts

Class 000 Parts

Taylor Part #072454 (Motor-24VDC *C832/C842*)

Four (4) years

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required

at time of service.

2. This limited warranty is valid only if the Part is installed and all required service work in connection with the

Part is performed by an authorized Taylor distributor or service agency.

3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation

location in the unit of original installation.

4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in

the Taylor Operator’s Manual.

5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.

6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate

Taylor Limited Warranty on freezer or grill equipment.

7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this

limited warranty.

1, 2

Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1

(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor

freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

131121

Limited Warranty on Parts

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:

1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of

defective Parts, replacement Parts, or new Parts.

2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning

of condensers or carbon and grease buildup.

3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including

the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper

assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but

not limited to the platen and plate, sides of the shroud or top of the shroud.

4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or

in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or

other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials

or cleaning processes not approved for use by Taylor.

5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any

release sheets and clips for the Product’s upper platen assembly.

6. External hoses, electrical power supplies, and machine grounding.

7. Parts not supplied or designated by Taylor, or damages resulting from their use.

8. Return trips or waiting time required because a service technician is prevented from beginning warranty

service work promptly upon arrival.

9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,

unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including

but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning

supplies.

10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake

or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,

accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or

water supply specification of the unit in which a part is installed; or Parts or the units in which they are

installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or

normal wear or deterioration.

11. Any Part purchased over the Internet.

12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the

inadequacy or interruption of electrical service.

13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is

installed will void this limited warranty.

15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY

NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from

jurisdiction to jurisdiction.

Model C713

Limited Warranty on Parts

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITATION OF WARRANTY

THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS

AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE

REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR

INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,

PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS

WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED

BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

LEGAL REMEDIES

The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or

complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other

correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072, U.S.A.

Limited Warranty on Parts

Model C713

Download from Www.Somanuals.com. All Manuals Search And Download.

START RELAY

(047702-27)

INTERNAL OVERLOAD

WHITE(120 VOLTS)

BLACK(230 VOLTS)

A.O. SMITH BEATER MOTOR WIRING

STEPS:

1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5

2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING)

FROM TERMINAL #5 TO TERMINAL #1.

COMPRESSOR

TERMINAL

COVER

START CAPACITOR

(047703)

WHITE

BLACK

RELAY

LINE

RUN

RELAY

NOTE: FOR CCWLE

BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6

CAP.

BLUE INTERNAL

BEATER MOTOR

CONTACTOR

BROWN

LINE

BROWN

ORANGE INTERNAL

RED INTERNAL

BLACK

EQUIPMENT

GROUND

START CAP.

BLUE

BLACK

BLUE

ABOVE ELECTRICAL DIAGRAM SHOWS WIRING NECESSARY

TO HOOK UP COMPRESSOR USING START AND RUN

CAPACITOR (CSR) WITH RELAY.

RUN CAPACITOR

BLEED RESISTOR

052396-1

CSR

BLUE

START CAPACITOR

SCHEMATIC WIRING DIAGRAM

USE T3 AND L3 WHEN

CP CONTACTS ARE NOT AVAILABLE

BLACK

FIG. 2

YELLOW INTERNAL

BLACK INTERNAL

START WINDING

MAIN WINDING

WINDING PROTECTOR

(INTERNAL)

LEESON BEATER MOTOR WIRING

STEPS:

1) DISCONNECT WIRE T7 FROM TERMINAL

2) SPLICE BLUE WIRE AS SHOWN

FIG. 1

COMPRESSOR WIRING

(MODEL TL3G W/HST)

EXTERNAL

GROUND

L1 L2

BEATER MOTOR

CONTACTOR

TERMINAL BLOCK

BLK

BLACK

BLUE

LEDS

LCD SCREEN

KEYS

BEEPER

RED (+5v)

BLK (GRD)

SV CABLE

USER

INTERFACE

BOARD

USE T3 AND L3 WHEN

CP CONTACTS ARE NOT AVAILABLE

BLACK

GRN/YEL

WHT

BLK

L1 LINE L2

EMI FILTER

L1 LOAD L2

WHT

RIBBON CABLE

CABLE

240V

NOT

CONNECTED

WHT

GE/RBC/MARATHON BEATER MOTOR WIRING

NOTE: FOR CCWLE BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

OPTIONAL COVER MOUNTED HOPPER AGITATOR

INTERFACE BOARD

POWER TRANSFORMER

16V

J13

J16

BEATER MOTOR

CONTACTOR

24VAC

J12 OR PURPLE INTERNAL

BLACK

J15

GRD

J12

208

COM WHT

T1 OR BLUE INTERNAL

T8 OR RED INTERNAL

BLUE

BLK

UNIVERSAL CONTROL PCB A.

J17

BLK

BLUE

BLK

CLR

OPTIONAL REAR

MIX LEVEL LIGHTS

J9 OR BLACK INTERNAL

J10

J11

CABLE

WHT

USE T3 AND L3 WHEN CP

RIBBON CABLE

RED

BLU

CONTACTS ARE NOT AVAILABLE

RED

BLU

RED

BLU

OUT

BLACK

T4 OR YELLOW INTERNAL

COM

208

GRN/YEL

SV CABLE

BLU/WHT

BLU

24 VAC

FIG. 3

BLUE

BLU/WHT

GND

+5V

J20

GRN

CLR

CABLE

BLK

ORN/WHT

RED/BLK

PRP

CABLE

GRN/YEL

COM

WHT/RED

HOPPER

GROUND

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

SELF-SERVICE

ENABLE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

DISABLE ENABLE

RED

WHT

BLK

WHT

OFF

SV CABLE

(OPTIONAL)

BLK

WHT

HOPPER

BARREL

--THERMISTOR PROBES--

234567

FUSE

15A

WHT/RED

BLK/WHT

BLK

OPTIONAL

BLK

BLK/WHT

BLK

POWER

SWITCH

DPDT

LEFT SYRUP HEATER

SEE FIG.

OFF

BEATER

INTERLOCK

RELAY

WHT/ORN

THERMOSTA

190

140

OPEN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

BLK

OFF

O.T.

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT

WHT/ORN

WHT

RED

COMPRESSOR

CONTACTOR

COIL

BLK

PANEL

JACK

SYRUP HEATER

96 95

BEATER

MOTOR

STARTER

COIL

BLACK

BLK BLK

BEATER

MOTOR

INTERLOCK

N.O. SWITCH

BEATER

MOTOR

OVERLOAD

SWITCH

FIG .4

RED

C0M

BLK

DRAW

SWITCH

BARREL LIQUID

SOLENOID

WHT

SEE FIG.

SOFT SERVE

GRN/YEL

BEATER MOTOR

CABLE

BLK_T2

BLK

BEATER MOTOR

STARTER

SOFT SERVE

COMPRESSOR

BEATER MOTOR

STARTER

BLK

L1 T1

T2 L2

COMPRESSOR

CONTACTOR

AIR COOLED

CONDENSER

BLOWER MOTOR

SEE FIG.

BLK

WHT

BLK

WATER COOLED

CONDENSER

FAN

MIX REF. SYSTEM

(DANFOSS TL3G COMPR.)

SEE FIG.

BLK

WHT

BRN

FAN

WHT

BRN

1014

¹¹¹³COMP

START RELAY

LEFT SIDE

CONTROL

START CAP

RIGHT SIDE

CONTROL

L1 L2

TERMINAL BLOCK

BLK

SV CABLE

BLU/WHT

RED

BLU

RED

BLU

RED

BLU

GRN/YEL

BLU

GND

+5V

BLK

CLR

BLK

CABLE

RED/BLK

GRA/BLK

PRP/WHT

J20

COM

MIX

OUT

PROBE

RED/BLK

DRAW

SWITCH

MIX

LOW

PROBE

BLK

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

WHT

BLK

WHT

BARREL

HOPPER

--THERMISTOR PROBES--

BLK

234567

FUSE

15A

BLK

WHT

OPTIONAL

BLU/WHT

BLK

WHT/ORN

RIGHT SYRUP HEATER

SEE FIG.

BEATER

INTERLOCK

RELAY

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

BLK

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

RED

BLK

COMPRESSOR

CONTACTOR

COIL

PANEL

JACK

96 95

BEATER

MOTOR

STARTER

COIL

BLK BLK

WHT

BEATER

MOTOR

OVERLOAD

SWITCH

WHT

RED

C0M

WHT

BLK

DRAW

SWITCH

WHT

BARREL LIQUID

SOLENOID

SEE FIG.

SOFT SERVE

GRN/YEL

BEATER MOTOR

BLK

BLK_T2

BEATER MOTOR

STARTER

BLK

SOFT SERVE

COMPRESSOR

BEATER MOTOR

STARTER

BLK

L1 T1

T2 L2

COMPRESSOR

CONTACTOR

SEE FIG.

C713

059899-27

12/9/13

Download from Www.Somanuals.com. All Manuals Search And Download.

THERMOSTA

EXTERNAL

GROUND

190

140

OPEN

O.T.

L1 L2 L3

WHT

TERMINAL BLOCK

BLK

SYRUP HEATER

LEDS

LCD SCREEN

KEYS

BEEPER

RED (+5v)

BLK (GRD)

SV CABLE

USER

INTERFACE

BOARD

FIG .2

GRN/YEL

WHT

GRN/YEL

WHT

BLK

L1 LINE L2

EMI FILTER

RIBBON CABLE

L1 LOAD L2

240V

NOT

CONNECTED

CABLE

WHT

OPTIONAL COVER MOUNTED HOPPER AGITATOR

INTERFACE BOARD

POWER TRANSFORMER

J13

J16

16V

24VAC

208

COM

BLK

J15

GRD

J12

WHT

UNIVERSAL CONTROL PCB A.

J17

BLK

CLR

OPTIONAL REAR

MIX LEVEL LIGHTS

J10

J11

CABLE

WHT

RIBBON CABLE

RED

BLU

RED

BLU

RED

BLU

OUT

FIGURE

COM

208

GRN/YEL

SV CABLE

BLU/WHT

BLU

START RELAY

(047702-27)

24 VAC

BLU/WHT

BLUE

ORN/WHT

GND

+5V

J20

GRN

CLR

CABLE

BLK

ORN/WHT

YEL

START CAPACITOR

(047703)

CABLE

RED/BLK

PRP

GRN/YEL

COM

WHT/RED

HOPPER

GROUND

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

SELF-SERVICE

ENABLE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

DISABLE ENABLE

RED

WHT

OFF

BLK

SV CABLE

BARRELHOPPER (OPTIONAL)

--THERMISTOR PROBES--

234567

FUSE

15A

WHT/RED

BLK

WHT

BLK

OPTIONAL

BLK/WHT

BLK

START WINDING

LEFT SYRUP HEATER

SEE FIG.

MAIN WINDING

POWER OFF

SWITCH

3PDT

BEATER

INTERLOCK

RELAY

WHT/ORN

WINDING PROTECTOR

(INTERNAL)

COMPRESSOR WIRING

(MODEL TL3G W/HST)

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

BLK

OFF

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

RED

COMPRESSOR

CONTACTOR

COIL

BLK

PANEL

JACK

96 95

BEATER

MOTOR

STARTER

COIL

BLACK

BLK BLK

BEATER

MOTOR

INTERLOCK

N.O. SWITCH

BEATER

MOTOR

OVERLOAD

SWITCH

RED

C0M

BLK

DRAW

SWITCH

WHT

BARREL LIQUID

SOLENOID

WHT

SOFT SERVE

BEATER MOTOR

GRN/YEL

CABLE

BLK

BLK_T2

BEATER MOTOR

STARTER

BLK

SOFT SERVE

COMPRESSOR

BEATER MOTOR

STARTER

BLK

L1 T1

T2 L2

T3 L3

AIR COOLED

CONDENSER

BLOWER MOTOR

BLK

WHT

COMPRESSOR

CONTACTOR

BLK

WATER COOLED

CONDENSER FAN

BLK

WHT

BRN

FAN

BRN

START RELAY

WHT

BRN

1014

¹¹¹³COMP

START CAP

MIX REF. SYSTEM

(DANFOSS TL3G COMPR.)

(ALSO SEE FIG.2)

LEFT SIDE

CONTROL

RIGHT SIDE

CONTROL

L1 L2 L3

TERMINAL BLOCK

BLK

SV CABLE

BLU/WHT

RED

BLU

RED

BLU

RED

BLU

GRN/YEL

GND

+5V

J20

BLK

CLR

BLK

CABLE

RED/BLK

GRA/BLK

PRP/WHT

COM

RED/BLK

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

WHT

BLK

BARRELHOPPER

--THERMISTOR PROBES--

234567

1234567

FUSE

15A

BLK

WHT

OPTIONAL

BLK

BLU/WHT

WHT

BLK

RIGHT SYRUP HEATER

SEE FIG.

BEATER

INTERLOCK

RELAY

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

BLK

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

RED

BLK

COMPRESSOR

CONTACTOR

COIL

PANEL

JACK

BEATER

MOTOR

STARTER

COIL

BLK BLK

WHT

BEATER

MOTOR

OVERLOAD

SWITCH

WHT

RED

C0M

WHT

BLK

DRAW

SWITCH

WHT

BARREL LIQUID

SOLENOID

SOFT SERVE

BEATER MOTOR

GRN/YEL

BLK

BLK_T2

BEATER MOTOR

STARTER

BLK

SOFT SERVE

COMPRESSOR

BEATER MOTOR

STARTER

BLK

L1 T1

T2 L2

BLK

T3 L3

COMPRESSOR

CONTACTOR

C713

059899-33

12/9/13

Download from Www.Somanuals.com. All Manuals Search And Download.

START RELAY

(047702-27)

INTERNAL OVERLOAD

WHITE(120 VOLTS)

BLACK(230 VOLTS)

A.O. SMITH BEATER MOTOR WIRING

STEPS:

1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5

2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING)

FROM TERMINAL #5 TO TERMINAL #1.

COMPRESSOR

TERMINAL

COVER

START CAPACITOR

(047703)

WHITE

BLACK

RELAY

LINE

RUN

RELAY

NOTE: FOR CCWLE

BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6

CAP.

BLUE INTERNAL

BEATER MOTOR

CONTACTOR

BROWN

LINE

BROWN

ORANGE INTERNAL

RED INTERNAL

BLACK

EQUIPMENT

GROUND

START CAP.

BLUE

BLACK

BLUE

ABOVE ELECTRICAL DIAGRAM SHOWS WIRING NECESSARY

TO HOOK UP COMPRESSOR USING START AND RUN

CAPACITOR (CSR) WITH RELAY.

RUN CAPACITOR

BLEED RESISTOR

052396-1

CSR

BLUE

START CAPACITOR

SCHEMATIC WIRING DIAGRAM

USE T3 AND L3 WHEN

CP CONTACTS ARE NOT AVAILABLE

BLACK

FIG. 2

YELLOW INTERNAL

BLACK INTERNAL

START WINDING

MAIN WINDING

WINDING PROTECTOR

(INTERNAL)

EQUIPOTENTIAL

GROUND

EXTERNAL

GROUND

LEESON BEATER MOTOR WIRING

STEPS:

1) DISCONNECT WIRE T7 FROM TERMINAL

2) SPLICE BLUE WIRE AS SHOWN

FIG. 1

COMPRESSOR WIRING

(MODEL TL3G W/HST)

TERMINAL BLOCK

BRN

BLK

BEATER MOTOR

CONTACTOR

BLACK

LEDS

LCD SCREEN

KEYS

BEEPER

RED (+5v)

BLK (GRD)

SV CABLE

USER

INTERFACE

BOARD

BLUE

BRN

BLU

ELECTRICAL

ENCLOSURE

GRN/YEL

WHT

USE T3 AND L3 WHEN

CP CONTACTS ARE NOT AVAILABLE

BLACK

BLK

WHT

L1 LINE L2

EMI FILTER

L1 LOAD L2

RIBBON CABLE

CABLE

240V

NOT

CONNECTED

WHT

INTERFACE BOARD

POWER TRANSFORMER

J13

J16

GE/RBC/MARATHON BEATER MOTOR WIRING

NOTE: FOR CCWLE BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

16V

OPTIONAL REAR

MIX LEVEL LIGHTS

BEATER MOTOR

CONTACTOR

J15

GRD

J12

J12 OR PURPLE INTERNAL

BLACK

UNIVERSAL CONTROL PCB A.

J17

OUT

T1 OR BLUE INTERNAL

T8 OR RED INTERNAL

BLUE

BLK

CLR

J10

J11

BLUE

J9 OR BLACK INTERNAL

RIBBON CABLE

GRN/YEL

RIBBON CABLE

RED

BLU

RED

BLU

RED

BLU

USE T3 AND L3 WHEN CP

CONTACTS ARE NOT AVAILABLE

240

COM

GRN/YEL

BLACK

SV CABLE

T4 OR YELLOW INTERNAL

BLU/WHT

24 VAC

FIG. 3

GND

+5V

J20

ORN/WHT

GRN

CLR

CABLE

BLK

ORN/WHT

YEL

RED/BLK

PRP

CABLE

GRN/YEL

COM

HOPPER

GROUND

WHT/RED

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

SELF-SERVICE

ENABLE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

DISABLE ENABLE

RED

WHT

OFF

BLK

WHT

SV CABLE

HOPPER (OPTIONAL)

BARREL

--THERMISTOR PROBES--

234567

FUSE

15A

WHT/RED

BLK

OPTIONAL

BLK/WHT

WHT

BLK

GRN/YEL

LEFT SYRUP HEATER

SEE FIG.

POWER OFF

SWITCH

3PDT

BEATER

INTERLOCK

RELAY

WHT/ORN

BLK

OFF

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

THERMOSTA

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

190

140

OPEN

RED

O.T.

COMPRESSOR

CONTACTOR

COIL

WHT

96 95

BEATER

MOTOR

STARTER

COIL

BLK

BLK BLK

BLACK

BEATER

MOTOR

INTERLOCK

N.O. SWITCH

PANEL

JACK

BEATER

MOTOR

OVERLOAD

SWITCH

SYRUP HEATER

FIG .4

BLK

RED

C0M

WHT

BARREL LIQUID

SOLENOID

DRAW

SWITCH

GRN/YEL

SEE FIG.

SOFT SERVE

BEATER MOTOR

BLK _T2

BLK

BEATER MOTOR

STARTER

GRN/YEL

BLK

SOFT SERVE

COMPRESSOR

BEATER MOTOR

STARTER

BLK

L1 T1

T2 L2

COMPRESSOR

CONTACTOR

SEE FIG.

GRN/YEL

RED

WHT

CONDENSER

BLOWER MOTOR

AIR COOLED

BLK

WHT

LEFT SIDE

CONTROL

WATER COOLED

CONDENSER FAN

GRN/YEL

RIGHT SIDE

CONTROL

BRN

FAN

WHT

BRN

GRN/YEL

1014

¹¹¹³COMP

BRN

START RELAY

START CAP

MIX REF. SYSTEM

(DANFOSS TL3G COMPR.)

SEE FIG.

TERMINAL BLOCK

BLK

BLK BRN

ELECTRICAL

ENCLOSURE

BRN

BLU

SV CABLE

BLU/WHT

RED

BLU

RED

BLU

RED

BLU

GRN/YEL

GND

+5V

J20

BLK

CLR

BLK

RED/BLK

GRA/BLK

PRP/WHT

CABLE

COM

RED/BLK

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

WHT

BLK

BARRELHOPPER

--THERMISTOR PROBES--

234567

FUSE

15A

WHT

OPTIONAL

BLU/WHT

BLK

GRN/YEL

RIGHT SYRUP HEATER

SEE FIG.

BEATER

INTERLOCK

RELAY

WHT/ORN

BLK

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

RED

COMPRESSOR

CONTACTOR

COIL

96 95

BEATER

BLK

BLK BLK

WHT

MOTOR

STARTER

COIL

PANEL

JACK

BEATER

MOTOR

OVERLOAD

SWITCH

WHT

BLK

RED

C0M

WHT

BARREL LIQUID

SOLENOID

DRAW

SWITCH

GRN/YEL

SEE FIG.

SOFT SERVE

BEATER MOTOR

BLK _T2

BLK

BEATER MOTOR

STARTER

BLK

T2 L2

SOFT SERVE

BEATER MOTOR

STARTER

COMPRESSOR

L1 T1

COMPRESSOR

CONTACTOR

GRN/YEL

SEE FIG.

C713

059899-40

12/9/13

Download from Www.Somanuals.com. All Manuals Search And Download.

EQUIPOTENTIAL

GROUND

EXTERNAL

GROUND

TERMINAL BLOCK

L1 L2 L3

BLK

BRN

THERMOSTA

190

140

OPEN

O.T.

LEDS

LCD SCREEN

KEYS

BEEPER

RED (+5v)

BLK (GRD)

USER

INTERFACE

BOARD

WHT

SV CABLE

WHT

SYRUP HEATER

GRN/YEL

WHT

ELECTRICAL

ENCLOSURE

GRN/YEL

WHT

FIG .2

BLK

L1 LINE L2

EMI FILTER

RIBBON CABLE

L1 LOAD L2

CABLE

240V

NOT

CONNECTED

WHT

INTERFACE BOARD

POWER TRANSFORMER

J13

OPTIONAL REAR

MIX LEVEL LIGHTS

J16

16V

J15

GRD

J12

OUT

UNIVERSAL CONTROL PCB A.

J17

BLK

CLR

J10

J11

BLK/RED

RIBBON CABLE

RED

BLU

FIGURE

WHT

COM

RED

BLU

RED

BLU

240

GRN/YEL

SV CABLE

START RELAY

(047702-27)

SV CABLE

BLU/WHT

BLU

24 VAC

BLUE

BLU/WHT

START CAPACITOR

(047703)

GND GRN

+5V

J20

BLK

ORN/WHT

YEL

CLR

CABLE

RED/BLK

PRP

CABLE

GRN/YEL

COM

HOPPER

GROUND

WHT/RED

MIX

OUT

PROBE

DRAW

SWITCH

BLK

MIX

LOW

PROBE

SELF-SERVICE

ENABLE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

DISABLE ENABLE

RED

WHT

BLK

OFF

SV CABLE

(OPTIONAL)

234567

BARRELHOPPER

--THERMISTOR PROBES--

FUSE

15A

WHT/RED

BLK

WHT

BLK

OPTIONAL

BLK

BLK/WHT

START WINDING

WHT

GRN/YEL

BLK

MAIN WINDING

BLK

LEFT SYRUP HEATER

SEE FIG.

POWER

SWITCH

3PDT

OFF

BEATER

INTERLOCK

RELAY

WINDING PROTECTOR

(INTERNAL)

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

COMPRESSOR WIRING

(MODEL TL3G W/HST)

BLK

OFF

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

BLK

RED

PANEL

JACK

COMPRESSOR

CONTACTOR

COIL

96 95

BEATER

MOTOR

STARTER

COIL

BLACK

BLK BLK

BEATER

MOTOR

INTERLOCK

N.O. SWITCH

BEATER

MOTOR

OVERLOAD

RED

C0M

SWITCH

DRAW

SWITCH

BLK

WHT

SOFT SERVE

BEATER MOTOR

GRN/YEL

BLK

BEATER MOTOR

BLK

STARTER

BARREL LIQUID

SOLENOID

BEATER MOTOR

STARTER

GRY/WHT

WHT

BLK

SOFT SERVE

COMPRESSOR

T2 L2

GRN/YEL

BLK

L1 T1

BLK

T3 L3

COMPRESSOR

CONTACTOR

GRN/YEL

CONDENSER

BLOWER MOTOR

BLK

RED

WHT

BRN

RED

WHT

AIR COOLED

WATER COOLED

CONDENSER FAN

GRN/YEL

WHT

BLK

BRN

FAN

CABLE

BRN

1014

¹¹¹³COMP

GRN/YEL

START RELAY

LEFT SIDE

START CAP

MIX REF. SYSTEM

(DANFOSS TL3G COMPR.)

(ALSO SEE FIG.2)

CONTROL

RIGHT SIDE

CONTROL

TERMINAL BLOCK

L1 L2 L3

BLK

BLK BRN

ELECTRICAL

ENCLOSURE

SV CABLE

BLU/WHT

RED

BLU

RED

BLU

RED

BLU

WHT

BLK

GRN/YEL

GND

+5V

J20

BLK

CLR

BLK

RED/BLK

GRA/BLK

PRP/WHT

CABLE

COM

MIX

OUT

PROBE

RED/BLK

DRAW

SWITCH

BLK

MIX

LOW

PROBE

INTFC PCB A.

WITH SOFT SERVE

PERSONALITY PCB A.

WHT

HOPPER

--THERMISTOR PROBES--

BLK

BARREL

234567

FUSE

15A

BLK

WHT

OPTIONAL

BLK

BLU/WHT

BLK

GRN/YEL

WHT/ORN

RIGHT SYRUP HEATER

SEE FIG.

BEATER

INTERLOCK

RELAY

WHT/ORN

ADDITIONAL DRAW SWITCH

FOR FLAVORBURST

BLK

COMPRESSOR

HIGH PRESSURE

LIMIT SWITCH

WHT/ORN

BLK

RED

PANEL

JACK

COMPRESSOR

CONTACTOR

COIL

BEATER

BLK BLK

WHT

MOTOR

STARTER

COIL

BEATER

MOTOR

OVERLOAD

SWITCH

RED

C0M

WHT

DRAW

SWITCH

BLK

SOFT SERVE

BEATER MOTOR

GRN/YEL

BLK

BEATER MOTOR

STARTER

BARREL LIQUID

SOLENOID

BEATER MOTOR

STARTER

GRY/WHT

WHT

BLK

SOFT SERVE

COMPRESSOR

GRN/YEL

BLK

L1 T1

T2 L2

BLK

T3 L3

COMPRESSOR

CONTACTOR

GRN/YEL

C713

059899-58

12/9/13

Download from Www.Somanuals.com. All Manuals Search And Download.

TDK Stereo System NX 7CD User Manual
Toastmaster Mixer 1776 User Manual
Toshiba MP3 Player SD V394 User Manual
Toshiba Network Card USB001Z User Manual
Trane Air Conditioner SCRH User Manual
Tripp Lite TV Cables N001 250 GY User Manual
Univex Offroad Vehicle Trail Blazer User Manual
Vacuflo Vacuum Cleaner 260 User Manual
Vantec Network Card CB ISATAU2 User Manual
Viking Range VISC530 4B User Manual