OPERATOR’S
MANUAL
Model 220
Batch Freezer
Original Operating Instructions
028763- M
5/99 (Original Publication)
(Updated 8/2/14)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
2
2
3
3
4
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Connections (Water Cooled Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 3
Section 4
5
7
8
9
Beater Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dial Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reset Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Overrun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Drawing Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Closing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning/Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Model 220
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents - Page 2
Section 7
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Section 9
Section 10
Section 11
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E 1999 Carrier Commercial Refrigeration, Inc. (Original Publication)
(Updated September, 2014)
028763- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties.
All rights reserved.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Model 220
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the
Installation Checklist.
This unit has many sharp edges that can
cause severe injuries.
Installer Safety
Site Preparation
In all areas of the world, equipment should be
installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Review the area the unit is to be installed in before
uncrating the unit making sure that all possible
hazards the user or equipment may come into have
been addressed.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor® equipment.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F (21_-24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
S
Only authorized Taylor service personnel
should perform installation and repairs on the
equipment.
S
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use a
water jet or hose to rinse or clean the unit. Failure to
follow this instruction may result in electrocution.
industry
standards
on lockout/tagout
procedures before beginning any installation
or repairs.
S
S
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and service.
Authorized service personnel must remove all
metal jewelry, rings, and watches before
working on electrical equipment.
This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should be
taken in moving this equipment for any reason. Two or
more persons are required to safely move this unit.
Failure to comply may result in personal injury or
equipment damage.
The main power supply(s) to the freezer must
be disconnected prior to performing any repairs.
Failure to follow this instruction may result in personal
injury or death from electrical shock or hazardous
moving parts as well as poor performance or damage
to the equipment.
Uncrate the unit and inspect it for damage. Report any
damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.
Note: All repairs must be performed by an
authorized Taylor Service Technician.
131122
1
Model 220
To the Installer
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Cooled Units
Electrical Connections
DO NOT obstruct air intake and discharge openings:
In the United States, this equipment is intended to be
installed in accordance with the National Electrical
Code (NEC), ANSI/NFPA 70-1987. The purpose of the
NEC code is the practical safeguarding of persons and
property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. In all other areas of the world,
equipment should be installed in accordance with the
existing local codes. Please contact your local
authorities.
Air cooled units require a minimum of 3” (76 mm) of
clearance around all sides of the freezer and 7- 1/2”
(191 mm) on the bottom to allow for adequate air flow
across the condenser(s). Install the deflector provided
to prevent recirculation of warm air. Failure to allow
adequate clearance can reduce the refrigeration
capacity of the freezer and possibly cause permanent
damage to the compressor.
Water Connections
(Water Cooled Units Only)
FOLLOW YOUR LOCAL ELECTRICAL CODES!
An adequate cold water supply must be provided with
a hand shut- off valve. On the underside rear of the
base pan, two 3/8” I.P.S. water connections for inlet
and outlet have been provided for easy hook- up. One
half inch inside diameter water lines should be
connected to the machine. (Flexible lines are
recommended, if local codes permit.) Depending on
local water conditions, it may be advisable to install a
water strainer to prevent foreign substances from
clogging the automatic water valve. There will be only
one water “in” and one water “out” connection. DO
NOT install a hand shut- off valve on the water “out”
line! Water should always flow in this order: first,
through the automatic water valve; second, through
the condenser; and third, through the outlet fitting to an
open trap drain.
Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity, and other electrical specifications. Refer to
the wiring diagram provided inside of the control box
for proper power connections.
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipment’s frame.
A back flow prevention device is required
on the incoming water connection side. Please
refer to the applicable National, State, and local codes
for determining the proper configuration.
120806
2
To the Installer
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Refrigerant
S
S
Stationary appliances which are not equipped
with a power cord and a plug or another device
to disconnect the appliance from the power
source must have an all-pole disconnecting
device with a contact gap of at least 3mm
installed in the external installation.
Appliances that are permanently connected to
fixed wiring and for which leakage currents
may exceed 10 mA, particularly when
disconnected or not used for long periods, or
during initial installation, shall have protective
devices such as a GFI, to protect against the
leakage of current, installed by the authorized
personnel to the local codes.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(Code designation 60245 IEC 57) installed
with the proper cord anchorage to relieve
conductors from strain, including twisting, at
the terminals and protect the insulation of the
conductors from abrasion.
In consideration of our environment, Taylor
uses only earth friendly HFC refrigerants. The HFC
refrigerant used in this unit is R404A. This refrigerant
is generally considered non-toxic and non-flammable,
with an Ozone Depleting Potential (ODP) of zero (0).
However, any gas under pressure is potentially
hazardous and must be handled with caution. NEVER
fill any refrigerant cylinder completely with liquid.
Filling the cylinder to approximately 80% will allow for
normal expansion.
S
Use only R404A refrigerant that conforms to
the AHRI standard 700 specification. The use of any
other refrigerant may expose users and operators to
unexpected safety hazards.
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe, apply
ice packs and contact a physician immediately.
Beater Rotation
Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory Service Department.
Note: The following procedures must be
performed by an authorized Taylor service
technician.
To correct the rotation on a three- phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.
To correct rotation on a single- phase unit, change the
leads inside the beater motor. (Follow the diagram
printed on the motor.)
WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely moisture
absorbent. When opening a refrigeration system, the
maximum time the system is open must not exceed 15
minutes. Cap all open tubing to prevent humid air or
water from being absorbed by the oil.
Electrical connections are made directly to the
terminal block provided in the main control box located
in the left lower side panel.
130821
3
Model 220
To the Installer
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
To the Operator
The freezer you have purchased has been carefully
engineered and manufactured to give you dependable
operation. Your Taylor freezer, when properly operated
and cared for, will produce aconsistent quality product.
Like all mechanical products, this machine will require
cleaning and maintenance. A minimum amount of care
and attention is necessary if the operating procedures
outlined in this manual are followed closely.
it must be collected separately after its use is
completed, and cannot be disposed as unsorted
municipal waste.
The user is responsible for returning the product to the
appropriate collection facility, as specified by your local
code. For additional information regarding applicable
local laws, please contact the municipal facility and/or
local distributor.
This Operator’s Manual should be read
before operating or performing any maintenance on
your equipment.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this unit are
warranted for the term stated in the Limited Warranty
section in this manual. However, due to the Montreal
Protocol and the U.S. Clean Air Act Amendments of
1990, many new refrigerants are being tested and
developed, thus seeking their way into the service
industry. Some of these new refrigerants are being
advertised as drop- in replacements for numerous
applications. It should be noted that in the event of
ordinary service to this unit’s refrigeration system,
only the refrigerant specified on the affixed data
label should be used. The unauthorized use of
alternate refrigerants will void your Taylor compressor
warranty. It is the unit owner’s responsibility to make
this fact known to any technician he employs.
Your Taylor freezer will NOT eventually compensate
and correct for any errors during the set- up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that all personnel responsible for the
equipment’s operation review these procedures in
order to be properly trained and to makesure that there
is no confusion.
In the event that you should require technical
assistance, please contact your local authorized
Taylor Distributor.
Note: Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor Distributor, and only if all required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on units or parts if non- Taylor
approved parts or incorrect refrigerant were installed
in the unit, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by abuse, misuse, neglect,
or failure to follow all operating instructions. For full
details of your Taylor Warranty, please see the Limited
Warranty section in this manual.
It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
refrigerant is lost during the course of ordinary service
to this machine, Taylor has no obligation to either
supply or provide its replacement either at billable or
unbillable terms. Taylor does have the obligation to
recommend a suitable replacement if the original
refrigerant is banned, obsoleted, or no longer available
during the five year warranty of the compressor.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
Taylor will continue to monitor the industry and test
new alternates as they are being developed. Should a
new alternate prove, through our testing, that it would
be accepted as a drop- in replacement, then the above
disclaimer would become null and void. To find out the
current status of an alternate refrigerant as it relates to
your compressor warranty, call the local Taylor
Distributor or the Taylor Factory. Be prepared to
provide the Model/Serial Number of the unit in
question.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore,
131122
4
To the Operator
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Safety
We, at Taylor Company, are concerned about the
safety of the operator at all times when they are
coming in contact with the unit and its parts. Taylor
makes every effort to design and manufacture built- in
safety features to protect both operators and service
technicians.
S
S
All repairs should be performed by an
authorized Taylor service technician.
The main power supplies to the unit must be
disconnected prior to performing installation,
repairs, or maintenance.
Installing and servicing refrigeration equipment can be
hazardous due to system pressure and electrical
components. Only trained and qualified service
personnel should install, repair, or service refrigeration
equipment. When working on refrigeration equipment,
observe precautions noted in the literature, tags and
labels attached to the unit, and other safety
precautions that may apply. Follow all safety code
requirements. Wear safety glasses and work gloves.
S
S
S
DO NOT operate the unit unless it is properly
grounded.
DO NOT operate the unit with larger fuses
than specified on the unit’s data label.
Units that are permanently connected to fixed
wiring and for which leakage currents may
exceed
10
mA,
particularly
when
disconnected or not used for long periods, or
during initial installation, shall have protective
devices such as a GFI, to protect against the
leakage of current, installed by the authorized
personnel to the local codes.
IMPORTANT - Failure to adhere to the
following safety precautions may result in severe
personal injury or death. Failure to comply with
these warnings may also damage the unit and/or
its components. Such damage may result in
component replacement and service repair
expenses.
S
S
Stationary units which are not equipped with
a power cord and a plug or another device to
disconnect the appliance from the power
source must have an all-pole disconnecting
device with a contact gap of at least 3 mm
installed in the external installation.
DO NOT operate the unit without reading
this entire Operator Manual first. Failure to follow all of
these operating instructions may result in damage to
the unit, poor performance, health hazards, personal
injury, or death.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(Code designation 60245 IEC 57) installed
with the proper cord anchorage to relieve
conductors from strain, including twisting, at
the terminals and protect the insulation of the
conductors from abrasion.
This unit is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge.
Where limited equipment operation is allowed for
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
public use, such as
a
self- serve application,
supervision or instruction concerning the use of the
appliance by a person responsible for their safety is
required. Children should be supervised to ensure that
they do not play with the appliance.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.
130821
5
Model 220
Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
An equipotential grounding lug is provided with this
unit. Some countries require the grounding lug be
properly attached to the rear of the frame by the
authorized installer. The installation location is marked
by the equipotential bonding symbol (5021 of IEC
60417-1) on both the removable panel and the unit’s
frame.
Access to the service area of the unit must be
restricted to persons having knowledge and practical
experience with the unit, in particular as far as safety
and hygiene are concerned.
Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to the
cleaning section of this Operator Manual for the proper
procedure to clean this unit.
DO NOT use a water jet to clean or rinse the
unit. Failure to follow these instructions may result in
serious electrical shock.
S
S
DO NOT allow untrained personnel to operate
this unit.
This unit is designed to maintain product
temperature under 41_F (5_C). Any product being
added to this unit must be below 41_F (5_C). Failure
to follow this instruction may result in health hazards
and poor freezer performance.
DO NOT operate the unit unless all service
panels and access doors are restrained with
screws.
DO NOT remove any internal operating parts
(including, but not limited to, freezer door,
beater, or scraper blades), unless all control
switches are in the OFF position.
S
DO NOT obstruct air intake and discharge openings:
3” (76 mm) minimum air space on front, rear and sides,
and 7- 1/2” (191 mm) on the bottom. The deflector
should be installed to prevent recirculation of warm air.
Failure to follow this instruction may cause poor
freezer performance and damage to the machine.
Failure to follow these instructions may result in severe
personal injury, especially to fingers or hands, from
hazardous moving parts.
This unit has many sharp edges that can
cause severe injuries.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F (21_-24_C). The unit has successfully
performed in high ambient temperatures of up to
104_F (40_C) at reduced capacities.
S
DO NOT put objects or fingers in the door
spout. This may contaminate the product and
cause severe personal injury from blade
contact.
USE EXTREME CAUTION when removing
the beater assembly. The scraper blades are
very sharp.
S
DO NOT run the unit without product. Failure to follow
this instruction can result in damage to the unit.
This unit must be placed on a level surface.
Extreme care should be taken when movingthe unit for
any reason. Two or more persons are required to
safely move this unit. Failure to comply may result in
personal injury or damage to the unit.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 1.0
meter from the surface of the unit and at a height of 1.6
meters from the floor.
6
Safety
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Operator Parts Identification
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
SHELF-DRIP TRAY
PART NO.
1
2
PAN-DRIP
027503
X24778
011412
031749
X35636
019566
033125
X49481
021279
12
13
14
15
16
17
18
19
20
21
22
031753
049441
019481
COVER A.-HOPPER-110-220
GASKET-HOPPER COVER
PANEL-REAR
PANEL-FRONT LOWER
COLLAR-HOLDING
3
4
FASTENER-CLIP 1/4-20 U-TYPE 045865
5
FUNNEL A.-MIX
PANEL A.-SIDE LEFT*
PANEL A.-FRONT
X49480
X32154
033124
013289
031895
031894
011471
6
LOUVER-SIDE L & R
PANEL-UPPER SIDE R.
PANEL A.-SIDE *RIGHT*
CASTER-SWV-3/4-10 ST.
7
PANEL-UPPER SIDE L.
BUSHING-PANEL
8
9
TRIM- REAR CORNER R.
TRIM- REAR CORNER L.
O- RING 1- 5/8 OD X .139 W
10
11
SCREW-1/4-20X3/8 RHM-STNLS 011694
CASTER-LOCKING SWIVEL 030307
7
Model 220
Operator Parts Identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Beater Door Assembly
ITEM
DESCRIPTION
ROD A.-DRAW
PART NO.
ITEM
DESCRIPTION
PART NO.
1
2
3
4
5
6
7
8
X30079
X30078
020051
030083
X04329
X34737
X32938
X29667
9
10
11
12
13
14
15
16
O-RING-11-3/8OD X .103W
BEARING-FRONT
BEATER A.
019046
019176
X32269
052586
032276
031316
X07233
011740
HOLDER A.-BEARING
O-RING-2-1/8 OD X .139W-#225
PISTON-VALVE
BLADE-SCRAPER
SHAFT-BEATER
PIN-HINGE
PIN A.-PIVOT
SEAL-DRIVE SHAFT
SCREW A.-CROSS BAR
BAR-CROSS
DOOR A.-PARTIAL SPOUT
CAP A.-COVER
8
Operator Parts Identification
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
2
3
4
PAIL- 10 QT.
013163
047518
023316
029670
5
6
7
BRUSH- REAR BRG 1 X 2 X 14
013071
LUBRICANT- TAYLOR
BRUSH- MIX TANK BODY 3 X 7
FUNNEL- PLASTIC DOOR
BRUSH- DRAW VALVE 1- 1/2 X 3 014753
PLUNGER A. X09585
140717
9
Model 220
Operator Parts Identification
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
Important: To the Operator
Figure 1
ITEM
DESCRIPTION
1
2
3
Control Switch (Switch- Rocker)
Dial Light (Light- Orange- Round)
Temperature Control (Control- Temp.)
Note: Never empty the contents of the
freezing cylinder while the control switch is in the
“AUTO” position. Always put the control switch into
the “EJECT” position when drawing product from the
freezing cylinder. As an additional safety feature, this
unit will not operate if the door is open.
Symbol Definitions
Dial Light
Located to the right of the control switch is a round dial
light. When the control switch is in the “AUTO”
position, this light will come on, indicating the
refrigeration system is operating.
To better communicate in the International arena, the
words on many of our operator switches and buttons
have symbols to indicate their functions. Your Taylor
equipment is designed with these International
symbols.
Temperature Control
The following chart identifies the symbol definitions
used on the operator switches.
Located on the right front side is the temperature
control knob. Turning the adjusting knob clockwise
will decrease product temperature. Turning the
adjusting knob counterclockwise will increase
product temperature. Each quarter turn will vary the
temperature approximately two degrees.
= COLDER
= WARMER
Reset Mechanism
= TEMP (Temperature)
Located on the left side panel is the reset button. The
reset protects the beater motor from an overload
condition. Should an overload occur, the reset
mechanism will trip. To properly reset the freezer,
place the control switch in the “OFF” position. Press
the reset button firmly. Place the control switch in the
“EJECT” position and observe the freezer’s
performance. Return the control switch to the “AUTO”
position.
Control Switch
When the control switch is placed in the “AUTO”
position, the refrigeration system will operate. When
the switch is placed in the “EJECT” position, only the
beater motor will operate.
10
Important: To the Operator
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6
Operating Procedures
The Model 220 freezer can produce all flavors of ice
cream, including those with fruits and nuts. Thefreezer
is designed for filling pints, quarts or gallons to be
placed in a hardening cabinet. The unit has a 10 quart
(9.5 liter) mix hopper.
The Model 220 will produce 20 quarts (18.9 liters) of
frozen product from 10 quarts (9.5 liters) of fresh mix.
We begin our instructions at the point where we find
the parts disassembled and laid out to air dry from the
previous brush cleaning.
The following procedures will show you how to
assemble the parts into the freezer, sanitize them, and
prime the freezer with fresh mix to prepare the first
batch.
Figure 2
If you are disassembling the machine for the first time
or need information to get to this starting point in our
instructions, turn to page 21, “Disassembly” and start
there.
Insert the drive shaft through the rear shell bearing,
and engage the hex end firmly into the gear box
coupling. Be certain that the drive shaft fits into the
coupling without binding.
Assembly
MAKE SURE THE CONTROL SWITCH IS
IN THE “OFF” POSITION. Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts.
Step 1
Install the drive shaft. Apply an even coat of lubricant
to the groove and shaft portion of the drive shaft. Do
not lubricate the hex end. Slide the shaft seal, small
end first, onto the shaft. Push the seal over the
shoulder and into the groove in the shaft. Apply
additional lubricant inside the large opening of theseal.
Figure 3
11
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2
Step 3
Install the beater assembly. First check the scraper
blades for any nicks or signs of wear. If the blades are
in good condition, place the rear scraper blade into the
grooves on the beater (knife edge to the outside). The
pins on the blades fit under the pins on the beater to
prevent the blades from falling off.
Assemble the freezer door. Insert the large o- ring
into the groove on the back of the freezer door.
Figure 6
Insert the front bearing into the hole in the center on the
back of the freezer door.
Figure 4
Holding the rear blade on the beater, slide the beater
assembly into the freezing cylinder over the drive shaft
until the entire blade is inside. Install the middle
scraper blade into the two middle holding pins. Slide
the beater assembly in farther and install the front
scraper blade into the two front holding pins. Slide the
beater assembly the rest of the way into the freezing
cylinder.
Figure 7
Slide the o- ring into the groove on the valve piston,
and lubricate.
Figure 5
Make sure the beater assembly is pushed all the way
to the rear of the freezing cylinder and that the end of
the beater shaft protrudes from the end of the beater
assembly. When in position, the beater will not
protrude beyond the front of the freezing cylinder.
Figure 8
12
Operating Procedures
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide the o- ring into the groove on the bearing holder,
and lubricate.
Lightly lubricate the inside of the valve body in the
freezer door.
Figure 9
Figure 12
Lightly lubricate the draw rod, and slide the bearing
holder onto the rod, locking stem first.
Insert the draw rod assembly, valve piston first, into the
valve body.
Figure 10
Figure 13
Thread the valve piston on the end of the draw rod until
tight.
Turn the draw rod handle to lock the bearing holder into
place.
Figure 11
Figure 14
13
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the bearing holder so the holes are aligned with
the holes in the valve body. Secure with the keeper pin.
Figure 17
Step 5
Align the holes in the cover cap assembly with the
holes on the freezer door. Secure with the keeper pin.
Figure 15
Step 4
Install the freezer door. Align the hole in the cross bar
with the hole in either hinge, and insert the hinge pin.
The cross bar can be assembled for either right or left
opening. Holding the freezer door firmly, position the
door onto the cross bar. Align the cross bar with the
opposite hinge and insert the remaining hinge pin.
Figure 18
Step 6
Slide the rear drip tray into the hole in the left side
panel.
Figure 16
Make sure the freezer door fits securely over the
freezing cylinder. With the door seated over the front
of the freezing cylinder, install the cross bar screw
assembly in the center of the freezer door through the
cross bar. Tighten securely.
Figure 19
14
Operating Procedures
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7
Step 2
Install the shelf. Choose the level desired and align
the grooves in the back of the shelf with the holding
collars. Slide the shelf down over the holding collars of
the same height on the left and right sides.
Install the o- ring on the bottom of the funnel.
Figure 22
Step 3
Lay the funnel and the hopper gasket in the bottom of
the mix hopper and pour the sanitizing solution into the
hopper.
Figure 20
Sanitizing
Step 1
Prepare a pail of approved 100 PPM sanitizing solution
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2 gal.
[7.6 liters] of Stera- SheenR). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S SPECIFIC-
ATIONS.
Figure 23
Step 4
While the solution is flowing into the freezing cylinder,
brush clean the hopper and the mix inlet hole.
Figure 21
Figure 24
080911
15
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6
Place the control switch in the “OFF” position.
With an empty pail beneath the ejection port, turn the
draw rod handle and pull forward, opening the ejection
port. Draw off all the sanitizing solution. When the
sanitizer stops flowing from the ejection port, push the
draw rod back into the valve body and lock into place.
Figure 25
Step 5
Place the control switch in the “EJECT” position. This
will cause the sanitizing solution in the freezing
cylinder to be agitated. Allow to agitate for five
minutes.
Figure 27
Step 7
Assemble the hopper gasket around the top edge of
the mix hopper.
Figure 26
Figure 28
140717
16
Operating Procedures
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
Priming
Turn the funnel to the right or left so that the opening
in the funnel aligns with the opening in the mix inlet
hole. Mix being added will force any remaining
sanitizing solution in the freezing cylinder out into the
pail.
Step 1
Place the funnel in the mix inlet hole at the rear of the
hopper. Turn the funnel to the right or left so that the
opening in the funnel does not align with the opening
in the mix inlet hole.
Figure 29
Figure 31
Step 2
Pour 10 quarts (9.5 liters) of FRESH mix into the
hopper. This should bring the mix level up to the
second graduated mark on the rear wall of the hopper.
Step 5
When full strength mix is flowing from the ejection port,
push the draw rod back into the valve body and lock
into place.
Step 3
With the control switch in the “OFF” position, hold an
empty pail beneath the ejection port. Turn the draw rod
handle and pull forward, opening the ejection port.
Figure 30
Figure 32
060425
17
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The funnel can be returned to its closed
position. Another measure of mix can be poured into
the hopper in readiness for the next batchwhile thefirst
batch of mix is freezing.
Figure 35
Step 8
To add fruits and nuts, place the control switch in the
“EJECT” position. There are two ways to add fruits
and nuts, as follows:
Fruits and nuts can be added through the mix hopper
funnel assembly. Use the plunger to press the
ingredients down into the freezing cylinder.
Figure 33
Fruits and nuts can also be added through the opening
in the freezer door. Install the white plastic door
funnel before using the plunger to press the
ingredients into the freezing cylinder.
Step 6
Place the mix hopper cover in position.
Figure 36
Note: The plastic door funnel MUST be installed
before using the plunger when addingfruits andnuts
through the opening in the freezer door. Failure to
install the door funnel may result in the plunger hitting
the beater assembly and damaging the machine.
Figure 34
If the plunger will not be used, fruits and nuts can be
added through the freezer door without installing the
plastic door funnel.
Step 7
Place the control switch in the “AUTO” position. When
the unit automatically cycles off, the light will turn off.
This light is a visual signal that the product is down to
its proper temperature. Place the control switch in the
“OFF” position.
Step 9
Thoroughly mix the added ingredients until the desired
consistency is obtained.
060425
18
Operating Procedures
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Overrun
With the control switch in the “EJECT” position, take
a sample of the product to determine overrun. If the
overrun is not at the desired level, leave the control
switch in the “EJECT” position to agitate the product
and blend more air into the mixture. Continue to take
samples until the desired overrun is obtained.
Step 1
Use a standard overrun scale and a one pint (1/2 liter)
measuring cup.
Step 2
Place the cup on the scale and adjust the scale pointer
to the zero setting.
Figure 39
Step 5
If the scale does not have overrun graduations, then
weigh one pint (1/2 liter) of mix before freezing. Draw
a sample pint (1/2 liter) of frozen product and level it off
with a straight edge.
Step 6
Place the pint (1/2 liter) of product on the scale and
read the weight. Divide the weight of the frozenproduct
into the weight of the raw mix for your percent of
increase. If the answer is 2, you have 100% overrun.
If the answer is between 1 and 2, the decimal
represents your overrun.
Example:
Figure 37
1.85
Step 3
8.2 15.2
Draw off one pint (1/2 liter) of product, and with a
straight edge, level off the top.
Raw Mix
Frozen Mix
=
=
15.2 oz. (450 ml)
8.2 oz. (243 ml)
Overrun = 85%
Drawing Product
Step 1
When the desired temperature and overrun of the
product has been achieved, the product may be drawn
into packages or cans for hardening. Place the
package or can directly beneath the ejection port of the
freezer door.
Step 2
Put the control switch into the “EJECT” position and
place the container on the shelf.
Figure 38
Step 4
Turn the draw rod handle and pull forward, opening the
ejection port. When the container is full, push the draw
rod back into the valve body and lock into place.
Place the pint (1/2 liter) of product on the scale and
read the overrun directly off of the scale.
19
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3
Step 3
When the freezing cylinder is empty of product, close
the ejection port and place the control switch in the
“OFF” position.
Put the control switch into the “EJECT” position and
allow the water to agitate for approximately one
minute.
Note: The shelf can be adjusted for large or small
containers. Lift upwards on the front edge of the shelf
to disengage from the holding collars; then lift away
from the freezer. Choose the desired height and slide
the shelf back down over the holding collars of the
same height on right and left sides.
Step 4
Put the control switch into the “OFF” position. Hold a
pail beneath the ejection port.
Step 5
Turn the draw rod handle and pull toward, opening the
ejection port. When the water stops flowing from the
ejection port, push the draw rod back into the valve
body and lock into place.
Repeat these procedures until the rinse water being
drawn from the freezing cylinder is clear.
Cleaning/Sanitizing
Step 1
Prepare a pail of approved 100 PPM cleaning/sanitiz-
ing solution (examples: 2- 1/2 gal. [9.5 liters] of
Kay- 5R or 2 gal. [7.6 liters] of Stera- SheenR). USE
WARM WATER AND FOLLOW THE MANUFACTUR-
ER’S SPECIFICATIONS.
Figure 40
Closing Procedures
Step 2
After the necessary batches have been prepared, the
machine should be cleaned and sanitized. The
following procedures will show you how to rinse the
freezing cylinder of mix residue, clean and sanitize,
and disassemble the parts from the freezer.
Pour the cleaning/sanitizing solution into the hopper
and allow it to flow into the freezing cylinder.
Step 3
While the solution is flowing into the freezing cylinder,
brush clean the hopper and the mix inlet hole.
Rinsing
Step 4
Put the control switch into the “EJECT” position. This
will cause the cleaning/sanitizing solution in the
freezing cylinder to be agitated. Allow it to agitate for
five minutes.
MAKE SURE THE CONTROL SWITCH IS
IN THE “OFF” POSITION. Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts.
Step 5
Put the control switch into the “OFF” position. Hold an
empty pail beneath the ejection port.
Step 1
Remove the hopper cover, the gasket and the funnel.
Take these parts to the sink for cleaning.
Step 6
Turn the draw rod handle and pull forward, opening the
ejection port. Draw off all the sanitizing solution. When
the sanitizer stops flowing from the ejection port, push
the draw rod back into the valve body and lock into
place.
Step 2
Pour two gallons (7.6 liters) of cool, clean water into
the mix hopper. With the brushes provided, scrub the
mix hopper and the mix inlet hole.
140717
20
Operating Procedures
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the keeper pin from the cover cap assembly
and remove the cover cap assembly.
Disassembly
Note: To remove o- rings, use a single service towel
to grasp the o- ring. Apply pressure in an upward
direction until the o- ring pops out of its groove. With
the other hand, push the top of the o- ring forward. It
will roll out of the groove and can be easily removed.
If there is more than one o- ring to be removed, always
remove the rear o- ring first. This will allow the o- ring
to slide over the forward rings without falling into the
open grooves.
MAKE SURE THE CONTROL SWITCH IS
IN THE “OFF” POSITION. Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts.
Step 1
Remove the cross bar screw assembly, the hinges,
pins, the cross bar, the freezer door, the beater
assembly, the scraper blades, and the drive shaft from
the freezing cylinder. Also remove the adjustable shelf.
Take these parts to the sink for further disassembly
and cleaning.
Take these parts to the sink for cleaning,
Step 2
Remove the rear drip tray from the side panel.
Step 4
Thoroughly brush clean all disassembled parts in the
cleaning solution, making sure all lubricant and mix film
is removed. Place all the cleaned parts on a clean dry
surface to air dry overnight.
Note: If the drip tray is filled with an excessive amount
of mix, it is an indication that the drive shaft seal should
be replaced or was improperly lubricated.
Step 5
Brush Cleaning
Return to the freezer with a small amount of cleaning
solution. With the black bristle brush, brush clean the
rear shell bearing at the back of the freezing cylinder.
Step 1
Prepare a sink with an approved cleaning solution (ex-
ample: Kay- 5R
or Stera- SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.
If an approved cleaner other than (example: Kay- 5R
or Stera- SheenR) is used, dilute it according to the
label instructions. IMPORTANT: Follow the label
directions. Too STRONG of a solution can cause parts
damage, while too MILD of a solution will not provide
adequate cleaning. Make sure all brushes provided
with the freezer are available for brush cleaning.
Step 2
Remove the seal from the drive shaft.
Step 3
From the freezer door:
Remove the keeper pin on the valve body. Turn the
draw rod handle and pull the draw rod assembly out of
the valve body. Unscrew the valve piston and slide the
bearing holder down off the draw rod. Remove the
o- ring from the valve piston and the bearing holder.
Remove the large o- ring and the front bearing from the
back of the freezer door.
Figure 41
Step 6
Wipe clean the shelf and all exterior surfaces of the
freezer.
21
Model 220
Operating Procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7
Important: Operator Checklist
During Cleaning and Sanitizing
Regular Maintenance Checks
Cleaning and sanitizing schedules are governed by
your State or local regulatory agencies and must be
followed accordingly. The following check points
should be stressed during the cleaning and sanitizing
operations.
j 1. Replace scraper blades that are nicked or
damaged. Before installing the beater, be
certain that the scraper blades are properly
attached.
j 2. Check the rear shell bearing for signs of wear
(excessive mix leakage in rear drip pan) and be
certain it is properly cleaned.
We recommend that after the necessary
batches have been prepared for the day, the
machine be cleaned and sanitized.
j 3. Using a screwdriver and cloth towel, keep the
rear shell bearing and the female hex drive
socket clean and free of lubricant and mix
deposits.
ALWAYS FOLLOW LOCAL HEALTH CODES.
Troubleshooting Bacterial Count
j 4. Dispose of o- rings and seals if they are worn,
torn, or fit too loosely, and replace with new
ones.
j 1. Thoroughly clean and sanitize the machine
regularly, including complete disassembly and
brush cleaning.
j 2. Use all brushes supplied for thorough cleaning.
The brushes are specially designed to reach all
mix passageways.
j 5. Follow all lubricating procedures as outlined in
“Assembly”.
j 3. Use the white bristle brush to clean the mix inlet
hole which extends from the mix hopper down
to the rear of the freezing cylinder.
j 6. If your machine is air cooled, check the
condenser for accumulation of dirt and lint. Dirty
condensers will reduce the efficiency and
capacity of the machine. Condensers should be
cleaned monthly with a soft brush.
j 4. Use the black bristle brush to thoroughly clean
the rear shell bearing located at the rear of the
freezing cylinder. Be sure there is a generous
amount of cleaning solution on the brush.
Note: For machines equipped with an air filter,
it will be necessary to vacuum clean the filters
on a monthly schedule.
j 5. Properly prepare the cleaning/sanitizing
solution. Read and follow the label directions
carefully. Too strong of a solution may damage
the parts and too weak of a solution will not do
an adequate job of cleaning and sanitizing.
Never use screwdrivers or other metal
probes to clean between the fins.
j 7. On water cooled units, check the water lines for
kinks or leaks. Kinks can occur when the
machine is moved back and forth for cleaning or
maintenance purposes. Deteriorated or
cracked water lines should be replaced only by
an authorized Taylor technician.
j 6. The temperature of the liquid mix should be
below 40_F. (4.4_C.).
j 7. The temperature of finished product to be
placed in a hardening cabinet should be
between 23_ and 25_F (- 5.0_ to - 3.9_C).
051101
22
Important: Operator Checklist
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Winter Storage
If the place of business is to be closed during the winter
months, it is important to protect the freezer by
following certain precautions, particularly if the
building is subject to freezing conditions.
Your local Taylor Distributor can perform this service
for you.
Wrap detachable parts of the freezer such as the
beater, blades, drive shaft, and freezer door. Place
these parts in a protected, dry place. Rubber trim parts
and gaskets can be protected by wrapping them with
moisture- proof paper. All parts should be thoroughly
cleaned of dried mix or lubrication which attract mice
and other vermin.
Disconnect the freezer from the main power source to
prevent possible electrical damage.
On water cooled freezers, disconnect the water
supply. Relieve pressure on the spring in the water
valve. Use air pressure on the outlet side to blow out
any water remaining in the condenser. This is
extremely important. Failure to follow this procedure
may cause severe and costly damage to the
refrigeration system.
080221
23
Model 220
Important: Operator Checklist
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8
Troubleshooting Guide
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
1. Unit will not run in the
a. Unit is unplugged.
a. Plug in wall receptacle.
b. Turn the breaker on.
- -
“AUTO” position.
b. Circuit breaker is off.
c. Unit is off on reset.
- -
10
c. Place control switch in the
“OFF” position. Press
reset button firmly. Place
control switch in the
“EJECT” position and
observe freezer’s
performance. Resume
normal operation.
2. Product is not freezing.
a. Dirty condensers.
a. Clean condensers
regularly.
22
18
22
b. The control switch is not in b. Place the control switch in
the “AUTO” position.
the “AUTO” position.
c. On water cooled units,
inadequate water supply.
c. Check to be sure the
water is turned on. Check
hoses for leaks or kinks.
3. Drive shaft is stuck.
a. Rounded corners on shaft, a. Replace the drive shaft,
- -
drive socket, or both. Do
not lubricate the hex end
of the drive shaft. Contact
a service technician.
drive socket, or both.
4. Walls of freezer cylinder
are scored.
a. Scraper blades were
improperly installed.
a. Install them properly.
a. Install or replace the seal.
b. Lubricate properly.
12
11
5. Excessive mix leakage in
the rear drip tray.
a. Drive shaft seal is worn or
missing.
b. Inadequate lubrication of
drive shaft seal.
11
c. Rear shell bearing is worn. c. Contact a service
technician.
- -
- -
- -
d. The wrong type of
d. Use Taylor Lube.
lubricant is being used.
6. Buzzer does not sound
when the freezer cycles
off.
a. Buzzer is malfunctioning.
a. Contact a service
technician.
(Note: the buzzer is an
optional feature.)
24
Troubleshooting Guide
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
7. Overrun is too low.
a. The temperature control is a. Adjust it accordingly.
set too cold.
10
b. Not enough air is blended
into the product.
b. Place the control switch in
the “EJECT” position to
blend in more air.
19
Continue blending until the
desired overrun is
achieved.
c. Improper priming
procedures.
c. Follow priming
procedures.
17
17
8. Overrun is too high.
a. Not enough mix is in the
freezing cylinder when
priming the machine.
a. Follow priming
procedures.
b. The temperature control is b. Adjust accordingly.
set too warm.
10
- -
c. Left in “EJECT” position
too long after drawing
c. After drawing out the first
portion, place the control
switch in the “OFF”
some product out to place
in hardening cabinet.
position. Return to freezer
to draw out more product,
place control switch in the
“EJECT” position.
25
Model 220
Troubleshooting Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9
Parts Replacement Schedule
PART DESCRIPTION
EVERY 3
MONTHS
EVERY 4
MONTHS
EVERY 6
MONTHS
ANNUALLY
QTY.
Front Bearing
X
1
3
1
1
1
2
Scraper Blades
Drive Shaft Seal
Funnel O- Ring
Freezer Door O- Ring
X
X
X
X
X
Bearing Holder and Valve Piston
O- Ring
Black Bristle Brush, 1” x 2”
White Bristle Brush, 1- 1/2” x 2”
White Bristle Brush, 3” x 7”
Inspect &
Replace if
Necessary
Minimum
Minimum
Minimum
1
1
1
Inspect &
Replace if
Necessary
Inspect &
Replace if
Necessary
26
Parts Replacement Schedule
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
Product
Soft Serve
Part
Limited Warranty Period
Five (5) years
Insulated shell assembly
Frozen Yogurt
Shakes
Refrigeration compressor
(except service valve)
Five (5) years
Beater motors
Two (2) years
Two (2) years
Two (2) years
Smoothies
Frozen Beverage
Batch Desserts
Beater drive gear
Printed circuit boards and
Softech controls beginning
with serial number H8024200
Parts not otherwise listed in
this table or excluded below
One (1) year
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.
2. This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.
3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5. The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.
131122
27
Model 220
Limited Warranty on Equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
28
Limited Warranty on Equipment
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 11
Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
Part’s Warranty Class Code or Part
Class 103 Parts¹
Limited Warranty Period
Three (3) months
Class 212 Parts²
Twelve (12) months
Twelve (12) months
No warranty
Class 512 Parts
Class 000 Parts
Taylor Part #072454 (Motor- 24VDC *C832/C842*)
Four (4) years
LIMITED WARRANTY CONDITIONS
1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.
2. This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.
3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.
7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.
1, 2
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131122
29
Model 220
Limited Warranty on Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.
3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.
4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.
5. Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.
6. External hoses, electrical power supplies, and machine grounding.
7. Parts not supplied or designated by Taylor, or damages resulting from their use.
8. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
30
Limited Warranty on Parts
Model 220
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
31
Model 220
Limited Warranty on Parts
Download from Www.Somanuals.com. All Manuals Search And Download.
BLUE
BLK CORD
RED/BLK
Y E L
G R N /
Y E L
G R N /
Y E L
G R N /
BLK CORD
BLK
BLK
BLK
BLK
Taylor Company
Model 220
030385
c
07/14
2014 Carrier Commercial Refrigeration, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BTR. MTR.
OVLD. CONTS.
BLACK
BLK
BLACK
WHITE W/BLUE
BLUE
95
96
DOOR SWITCH
H P SWITCH
(OPTIONAL)
BUZZER
YELLOW
WHITE
WHITE
WHITE
1
BLUE
TEMP. CONT.
1 AUTO
2
WHITE
2
3
DIAL LIGHT
3 BEATER
4 AUTO
5
RED/BLK
RED/BLK
A2
A1
COMP.
RELAY
ORANGE
WHITE
6 BEATER
CONT. SWITCH
A2
BEATER A1
RELAY
BEATER CONTACTOR
BLACK
BLACK
T3
T2
T3
L3
BLACK
BLACK
BLACK
BLACK
M
T1
T1
BEATER CONTACTOR
L1
T2
L2
BEATER CONTACTOR
BEATER MOTOR
COMPRESSOR CONTACTOR
BLACK
BLACK
BLACK
T3
COMPRESSOR CONTACTOR
BLACK
L3
COMPRESSOR CONTACTOR
BLACK
BLACK
M
T1
L1
T2
L2
COMPRESSOR
BLK
WHT
M
COND. BLOWER
(AIR COOLED ONLY)
BLACK
BLACK
M
CABINET BLOWER
(WATER COOLED ONLY)
NOTES:
L1
L2
L3
1. GROUND FRAME SECURELY. COMPRESSOR AND
BEATER PROTECTED UNDER PRIMARY
SINGLE PHASING CONDITIONS.
EQUIPOTENTIAL
GROUND
2. DIAL LIGHT ON WHEN COMPRESSOR ON AND
OFF WHEN COMPRESSOR OFF.
3. BUZZER (OPTIONAL) SIGNALS COMPRESSOR OFF.
Taylor Company
Model 220
030385-33
07/14
c
2014 Carrier Commercial Refrigeration, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BTR. MTR.
OVLD. CONTS.
BLACK
BLACK
BLACK
WHITE W/BLUE
PANEL/CHASSIS
GROUND
95
96
DOOR SWITCH
H P SWITCH
BLUE
(OPTIONAL)
BUZZER
YELLOW
WHITE
1
BLUE
TEMP. CONT.
1 AUTO
2
WHITE
WHITE
WHITE
2
3
DIAL LIGHT
3 BEATER
RED/BLK
RED/BLK
4 AUTO
A2
A1
COMP.
RELAY
5
ORANGE
WHITE
6 BEATER
A2
BEATER A1
RELAY
BEATER CONTACTOR
BLACK
BLACK
T3
T3
L3
GRN W/YEL
BLACK
BLACK
BLK
BLACK
T1
L1
BEATER CONTACTOR
T2
T2
L2
T1
BEATER MOTOR
BEATER CONTACTOR
COMPRESSOR CONTACTOR
BLACK
BLACK
T3
L3
GRN W/YEL
BLACK
BLACK
BLACK
BLACK
T1
T2
L1
L2
COMPRESSOR
COMPRESSOR
CONTACTOR
COMPRESSOR
CONTACTOR
BLK
WHT
BLK CORD
GRN W/YEL
COND. BLOWER
(AIR COOLED ONLY)
BLACK
BLACK
GRN W/YEL
CABINET BLOWER
(WATER COOLED ONLY)
NOTES:
1. GROUND FRAME SECURELY. COMPRESSOR AND
BEATER PROTECTED UNDER PRIMARY
SINGLE PHASING CONDITIONS.
L1
L2
L3
N
2. DIAL LIGHT ON WHEN COMPRESSOR ON AND
OFF WHEN COMPRESSOR OFF.
3. BUZZER (OPTIONAL) SIGNALS COMPRESSOR OFF.
EQUIPOTENTIAL
GROUND
Taylor Company
Model 220
030385-62
07/14
c
2014 Carrier Commercial Refrigeration, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|