Tascam Lawn Mower FW1082 User Manual

TASCAM FW-1082  
Cakewalk SONAR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Details  
Generally the FW-1082’s surface controls will function as expected, controlling their like  
parameters in Sonar. For example: Faders, Mutes, Solos and Transport Control will  
control those parameters in Sonar. Exceptions and specific details follow:  
Additional Transport Keys  
SET + REW = RTZ  
SET + FF = Go to Tail  
IN locates to the beginning of the selection area  
OUT locates to the end of the selection area  
SET + IN sets Punch IN point at the current playhead position  
SET + OUT sets Punch OUT point at the current playhead position  
SET + REC starts automation recording. A parameter must be armed for automation.  
SHIFT + SET + IN sets Loop In Point at the current playhead position  
SHIFT + SET + OUT sets Loop Out Point at the current playhead position  
SHIFT + IN = sets Selection In Point at the current playhead position  
SHIFT + OUT = sets Selection Out Point at the current playhead position  
<<LOCATE locates to previous marker  
LOCATE>> locates to next marker  
SET + LOCATE>> = Drop Marker at the current playhead position  
Transport Wheel  
Turn the data wheel clockwise to jog forward or counter-clockwise to jog  
backward.  
When the SHTL key is off, the data wheel moves the transport in one measure  
steps. Holding the SHIFT key reduces this to one-beat steps.  
When the SHTL key is on, the data wheel moves the transport in 1000-tick steps.  
Holding the SHIFT key reduces this to 100-tick steps.  
Special Keys  
SHIFT + PLAY toggles the Audio Engine On/Off  
SHIFT + STOP Resets Sonar  
SHIFT + any SOLO key will un-solo all tracks.  
SELect Keys  
Pressing an FW-1082 SELect key alone will select that channel in Sonar. Holding  
SHIFT while pressing SELect sets that channel’s fader to Unity in Sonar.  
Holding the red REC key while pressing a SELect key will record-enable/disable that  
track.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Pan & EQ  
When the EQ/PAN LED is illuminated:  
The lowest of the four encoders shown at  
right will control the Pan parameter of the  
SELected channel in Sonar.  
The encoders labeled as GAIN,  
FREQuency and Q will control those  
parameters of the EQ band selected by the  
illuminated buttons on the SELected  
channel in Sonar. Bands 1-4 of Sonar’s  
Channel EQ is supported.  
The first time an EQ Band key is pressed,  
it selects the appropriate lower band,  
pressing the same button again selects a  
higher band. In this way, up to eight  
bands can be controlled. (Note: The  
Sonar Channel Strip EQ does not support  
external control of more than four bands.)  
Holding SHIFT while pressing an EQ  
band key will enable/disable that EQ  
band.  
Holding the SET key while pressing an  
EQ band key will toggle through the  
available EQ curve types.  
Sonar can come with up to three types of EQ,  
depending on the version you have. The FW-1802 can be set to control any of the three:  
Hold the EQ/PAN key while pressing one of the top three EQ band buttons to  
select an EQ:  
o EQ HI = Channel Strip Sonitus  
o EQ HI MID = Plug-in Sonitus  
o EQ LO MID = Plug-in FX EQ  
Aux  
When AUX 1-4 or AUX 5-8 is illuminated:  
The four encoders control the level of Aux Sends 1 – 4 or Aux Sends 5 – 8 of the  
SELected channel in Sonar.  
Holding SHIFT while turning and encoder will adjust that Aux Send Pan.  
The four keys toggle Aux Send 1 – 4 enable/disable or Aux Send 1 – 5  
enable/disable of the SELected channel in Sonar.  
Holding SHIFT while pressing one of the four keys toggles the Pre/Ppost state for  
that Aux Send of the SELected channel in Sonar.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
F-Key Shortcuts  
The functions of the F-Keys are programmable in Sonar by selecting TASCAM FW-1082  
under the Tools menu. The screen below will appear where you can configure the F-  
Keys and save/load configurations.  
Factory default settings are shown here:  
F1 = Save  
F2 = Undo  
F3 = Copy  
F4 = Paste  
SHIFT + F1 = Enter  
SHIFT + F2 = Redo  
SHIFT + F3 = Cut  
SHIFT + F4 = Delete  
Arrow (Cursor) Keys  
Use the Arrow keys to navigate around the on-screen menus, sub-menus and menu items.  
Master Fader Assignment  
You can switch the master fader assignment to the next or previous virtual main by  
holding down SET while you press either the <BANK or BANK> key. The BANK LED  
indicators will show which virtual Master the master fader is being assigned to.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Bank Keys  
Press the BANK> key or the <BANK key, to shift the FW-1082's controls to the next 8 or  
previous 8 channels, respectively.  
Hold SHIFT and press the BANK> key or the <BANK key, to shift the FW-1082's controls  
to the next or previous channel, respectively.  
Hold SET and press the BANK> key to re-map all faders, mutes, solos and pans to Output  
Busses (Master, Groups, Aux Sends) in groups of 8. The corresponding BANK LED will  
flash when in this mode.  
Hold SET and press the <BANK key to go to previous Output Busses or switch back to  
normal track operation.  
Flip  
Pressing EQ/PAN while holding SHIFT will toggle Flip mode. While in Flip mode, the  
faders can be used to control channel pan.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Thule Automobile Accessories 053 User Manual
Timex Heart Rate Monitor W 201 User Manual
Toshiba TV VCR Combo MV13Q41 User Manual
Trane Heat Pump DC UC WEB01 User Manual
Transition Networks Network Router SSEFE10XX 10X User Manual
Tributaries TV Cables HXC5 User Manual
Tripp Lite Surge Protector 200407148 User Manual
Uniden Two Way Radio PRO520E User Manual
Universal Power Group Laptop XPAL Victor User Manual
VocoPro Stereo Amplifier DA 8909RV User Manual