D00927920A
»
DV-RA1000HD
High Definition Audio Master Recorder
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETYINSTRUCTIONS
• Do not expose this apparatus to drips or splashes.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
• Do not place any objects filled with liquids, such as
vases, on the apparatus.
• Do not install this apparatus in a confined space such
as a book case or similar unit.
4 Follow all instructions.
• The apparatus draws nominal non-operating power
from the AC outlet with its POWER switch in the off
position.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
• The apparatus should be located close enough to the
AC outlet so that you can easily grasp the power cord
plug at any time.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• An apparatus with Class I construction shall be con-
nected to an AC outlet with a protective grounding
connection.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
• Batteries (battery pack or batteries installed) should
not be exposed to excessive heat such as sunshine,
fire or the like.
10 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
TASCAM DV-RA1000HD
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
SafetyInformation
This product has been designed and manufactured
according to FDA regulations "title 21, CFR, chapter
1, subchapter J, based on the Radiation Control for
Health and Safety Act of 1968", and is classified as
a class 1 laser product. There is no hazardous invis-
ible laser radiation during operation because invisible
laser radiation emitted inside of this product is com-
pletely confined in the protective housings.
CAUTION
• DO NOT REMOVE THE PROTECTIVE HOUSING
USING A SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
• IF THIS PRODUCT DEVELOPS TROUBLE,
CONTACT YOUR NEAREST QUALIFIED SERVICE
PERSONNEL, AND DO NOT USE THE PRODUCT
IN ITS DAMAGED STATE.
The label required in this regulation is shown at 1.
1
For USA
Optical pickup:
Type: SF-DS10L
Manufacturer: Sanyo Electric Co,Ltd.
Laser output: CD/108 mW max
DVD/66 mW max
Wavelength: CD/782 nm
DVD/658 nm
ꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 − Introduction
5 − CD playback & recording
About this manual .......................................... 7
Notes and warnings............................................... 8
Copyright ................................................................ 8
Playback.........................................................30
DVD HD
Basic playback operation
................... 30
DVD HD
Display
................................................. 30
DVD HD
Programmed playback
....................... 30
Supplied accessories ....................................... 8
Rack-mounting the unit.................................. 8
Environmental considerations ....................... 9
Handling of optical discs ....................................... 9
Never use a stabilizer or printable discs..............10
Beware of condensation.......................................10
About CD-R and CD-RW discs...................... 10
About DVD R and DVD RW discs............... 11
DVD HD
Repeat playback
..................................31
DVD HD
Single track playback
Auto space playback
..........................31
...........................31
DVD HD
DVD HD
DVD HD
Jog playback
Pitch change
....................................... 32
........................................ 32
DVD HD
Auto cue
.............................................. 32
DVD HD
Auto ready
.......................................... 32
DVD HD
Fades
.................................................... 33
2 − Names and functions
DVD HD
Timer start
.......................................... 33
Front panel .................................................... 12
Remote control unit...................................... 14
Keys found on only the remote control unit ......14
Recording....................................................... 33
DVD RW HD
Basic recording operation
................. 33
DVD RW HD
Auto track increment
........................ 34
Keys that features the same functions as
those on the main unit.......................................14
DVD RW HD
Synchronized recording
.................... 35
Settings in the sound level screen...................... 35
Keys that feature the same functions as
the switches on the virtual front panel ............15
DVD HD
Monitoring
.......................................... 37
............................................. 37
DVD HD
Oscillator
Dithering............................................................... 37
Copy protection.................................................... 37
Finalizing discs...................................................... 38
Unfinalizing discs ................................................. 38
Erasing discs (CD-RW).......................................... 38
DVD RW HD
3 − Connections
Analog audio connections............................ 16
Digital audio connections............................. 16
Other connections......................................... 17
4 − Basic operations
About marks
.................................. 39
Jumping to a mark ............................................... 39
Editing marks........................................................ 39
HDD and ODD ............................................... 18
Drive mode ............................................................18
Storage media .......................................................18
Shut down ..................................................... 19
LCD screens.................................................... 19
Navigating the screens .........................................19
Adjusting the display contrast.............................19
The “home” screen........................................20
“Home” screen content........................................ 20
Menu operations........................................... 21
Menu tree ............................................................. 22
The virtual front panel (VFP)........................ 23
General preferences......................................24
Short cuts for screen access ......................... 25
Clock/calendar............................................... 26
The check screen........................................... 26
Selecting the input source............................ 27
Adjusting the input level.............................. 28
Selecting the reference clock....................... 28
Naming files, projects, marks, etc. .............. 29
6 − DVD RW/HD playback & recording
Organization of projects and files...............40
Writing the UDFMI............................................... 40
Viewing the number of rewriting times ............ 40
Recording times and track lengths......................41
Using a new DVD RW disc...................................41
Close and open operations for DVD-RW discs... 43
Adding a new project .......................................... 43
Adding notes to a project.................................... 43
Changing the current project.............................. 44
Changing the name of a project ......................... 44
Deleting a project from disc................................ 44
Formatting a disc.................................................. 44
Recording files to disc.......................................... 45
Recording mode ................................................... 45
Playing back files.................................................. 46
Play lists ................................................................ 46
TASCAM DV-RA1000HD
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Restructuring the play list ................................... 46
Setting marks ....................................................... 46
Erasing a file ..........................................................47
Renaming a file......................................................47
Editing files.................................................... 47
Combining files......................................................47
Dividing files......................................................... 48
Undo and redo...................................................... 48
Effect libraries ............................................... 57
Recalling library data........................................... 57
Storing library data.............................................. 57
Naming library data............................................. 58
9 − Use with a computer
Connecting the DV-RA1000HD to a computer... 59
Disconnecting from Windows 2000 / XP
systems ............................................................... 59
Disconnecting from Mac OS X systems.............. 59
After “ejecting” from the computer................... 59
Transferring audio files........................................ 60
7 − Copy function
Selecting a copy mode and copy source ..... 49
Same project name in the destination ............... 50
Transferring files between a DVD disc and
a computer.......................................................... 60
Copying files and projects from a DVD to
the HD..........................................................50
Copying files and projects from the HD to
DVD .............................................................. 51
Creating an audio CD using a project on
the HD.......................................................... 52
Copying tracks from a CD to the HD ........... 53
10 − Specifications, etc.
Analog I/O ..................................................... 61
Digital I/O ...................................................... 61
Other connections......................................... 62
Audio performance....................................... 63
Physical, etc. specifications .......................... 63
Dimensional drawing....................................64
Block diagram................................................ 65
8 − Effects
Setting up the effect position...................... 55
Equalization................................................... 55
Dynamics processor ...................................... 56
ꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
1 − Introduction
Thank you for your purchase of the TASCAM
DV-RA1000HD High Definition Audio Master
Recorder. This unit features the world's most advanced
method of recording high-resolution stereo audio on
optical disc or internal hard disk.
DVD R
These discs enable you to duplicate audio data once it
has been recorded on a DVD±RW disc or hard disk.
These discs are useful for archiving data that has been
recorded on the DV-RA1000HD.
Fitted with digital I/O in all common formats, including
SDIF-3 (direct stream digital), as well as high-quality
AD and DA conversion: the unit allows you to record
and playback the following types of disc. (See “Storage
The unit may be connected to a personal computer
through a USB 2.0 connection, and these files can be
transferred for further processing, editing and master-
ing. The files may then be used for the production of
high-resolution, high-sampling frequency SACD and
DVD-audio, etc. media, as well as for more convention-
al CDs.
CD-R and CD-RW
These discs enable you to record audio in CD-DA for-
mat from the DV-RA1000HD.
The DV-RA1000HD is also capable of creating audio
compact discs (CDs) using audio tracks recorded on its
hard disk, as well as copying audio CDs.
In addition, the unit provides digital effects: a 3-band
EQ with a fully-parametric mid band, and a dynamics
processor operating in one or three bands as either a
compressor or expander. These effects may be inserted
on recording (and the effect written to disc) or play-
back.
DVD RW and HD (internal hard disk)
These discs are used to record audio files which are
compatible with computer based digital audio work-
stations, and recording can take place at 44.1/48 kHz,
88.2/96 kHz, 176.4/192 kHz sampling frequencies (all at
24-bit) as well as in DSD format.
Before connecting and using the unit, please take time
to read this manual thoroughly to ensure you under-
stand how to properly set up and connect the unit, as
well as the operation of its many useful and convenient
functions. After you have finished reading this manual,
please keep it in a safe place for future reference.
The disc created in this way are in UDF 1.5 format.
This format is readable by personal computer system.
About this manual
In this manual, we use the following conventions:
3 - “Connections” (p. 16) Describes connections to
external devices.
• The names of keys and controls are given in the fol-
lowing typeface: ERASE.
4 - “Basic operations” (p. 18) Introduces the
basic principles and common operations of the
DV-RA1000HD and the remote control unit.
• When the alphanumeric portion of the display shows
a message or a parameter value (incl. on or off), they
are shown in the following typeface: No Disc.
5 - “CD playback & recording” (p. 30) Describes
the functions available when the DV-RA1000HD is
used as a CD player and recorder. Many playback func-
tions can be used in the same manner to play DVD±RW
discs, DVD±R discs, or the HD. Also, many recording
functions can be used in the same manner to record to
DVD±RW discs or the HD.
• If a preset indicator or a name of a parameter in the
display (i.e. one which can not change) is shown, this
is shown as follows: PROJECT.
• Unless otherwise specified, “HD” refers to the inter-
nal hard disk of the DV-RA1000HD.
• “DVD” refers to a DVD±RW and DVD±R disc.
The sections of this manual are arranged as follows:
(p. 40) Describes using the DV-RA1000HD as a DVD/
HD recorder, as well as editing and playing back files.
1 - “Introduction” (p. 7) (This chapter) Includes a
brief introduction to the DV-RA1000HD, precautions,
and information about optical disc media.
7 - “Copy function” (p. 49) The DV-RA1000HD
copy function enables you to duplicate a disc or copy
files between discs. You can use DVD±RW, DVD±R,
CD-R, or CD-RW discs or the HD as the copy source or
the copy destination.
2 - “Names and functions” (p. 12) Outlines the
function of each component on the front panel and the
remote control unit. Refer to Chapter 3 for information
on the rear panel connectors.
8 - “Effects” (p. 55) Describes how to use the built-
in effects (EQ and dynamics).
TASCAM DV-RA1000HD
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
1 − Introduction
9 - “Using with a computer” (p. 59) Describes
how to use the DV-RA1000HD when it is connected to
a computer.
10 - “Specifications” (p. 61) Includes the specifi-
cations and diagrams of the DV-RA1000HD.
Notes and warnings
mance may suffer if the instructions are not followed.
WARNING
These warnings should be taken very seriously.
They describe situations which can cause injury, or
damage to equipment if the instructions are not fol-
lowed.
NOTE
These notes provide additional explanations for
special cases, etc.
TIP
CAUTION
We give hints and tips on using the unit in this way.
Cautions show that you may lose data or perfor-
Copyright
you own the copyright, or have obtained the ap-
propriate permission from the copyright holder or
the rightful licensor, your unauthorized recording,
reproduction or distribution thereof may result in
severe criminal penalties under copyright laws and
international copyright treaties. If you are uncertain
about your rights, contact your legal advisor. Under
no circumstances will TEAC Corporation be re-
sponsible for the consequences of any illegal copy-
ing performed using the DV-RA1000HD.
Windows, Windows XP, Windows 2000, Windows
Me, Windows 98 and Windows 95 are trademarks of
Microsoft Corporation.
Macintosh, MacOS, and MacOS X are trademarks of
Apple Computer.
NOTE
This product is designed to help you record and
reproduce sound works to which you own the copy-
right, or where you have obtained permission from
the copyright holder or the rightful licensor. Unless
Supplied accessories
In addition to this manual, the DV-RA1000HD has
been packed with the following:
NOTE
When transporting the unit, always use the origi-
nal packing materials. For this reason, we strongly
recommend that you save all the packing materials
that came with the unit, in case you need to trans-
port it in the future.
• RC-RA1000 wired remote control unit ....................1
• AC power cable.........................................................1
• A rack-mounting screw kit (screws and washers).....1
• A warranty card ........................................................1
In addition, please close the disc tray when trans-
porting the unit.
Contact your TASCAM supplier if any of these items
are missing.
Rack-mounting the unit
If you are mounting the unit in a rack, leave 1U of space
above it and 4 inch (10 cm) or more of space at the rear.
Use the rack-mounting kit to mount the unit in a stan-
dard 19-inch equipment rack, as shown in this section.
Remove the feet of the unit before mounting.
Figure 1.1: Installing the DV-RA1000HD
ꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
1 − Introduction
Environmental considerations
The unit may be used in most areas, but to maintain top
performance, and prolong operating life, observe the
following environmental conditions:
• As the unit may become hot during operation, always
leave sufficient space above the unit for ventilation.
Do not install this unit in a confined space such as a
bookcase, and do not put anything on top of the unit.
• Avoid exposing it to extremes of temperature and
humidity and avoid mechanical shocks and vibration.
• Avoid installing this unit on top of any heat-generat-
ing electrical device such as a power amplifier.
• Keep the unit away from strong magnetic fields (TV
sets, computer monitors, large electric motors, etc.).
• The voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in any
doubt regarding this matter, consult an electrician.
• The nominal temperature should be between 5°C and
35°C (41°F and 95°F).
• Make sure that the unit is mounted in a level position
for correct operation.
• Relative humidity should be 30 to 90 percent.
Handling of optical discs
Observe the following:
• Never use such chemicals as record sprays, antistatic
sprays or fluid, benzine or thinner to clean compact
discs. Such chemicals will do irreparable damage to
the disc’s plastic surface.
• Always place discs in the tray with their label facing
upward (discs used in the DV-RA1000HD can only
be played on one side).
• Discs should be returned to their cases after use to
avoid serious scratches that could cause the laser
pickup to “skip”.
• To remove a disc from its storage case, press down
on the center of the case, and lift the disc out, hold-
ing it carefully by the edges.
• Don’t expose discs to direct sunlight or high humid-
ity and temperature for extended periods.
Long exposure to high temperature can warp the
disc.
• Only use circular discs. Avoid using non-circular
promotional, etc. discs.
Figure 1.2: Handling of discs
• Finger marks and dust should be carefully wiped off
the disc’s recorded surface with a soft cloth.
Unlike conventional records, the compact disc has
no grooves to collect dust and microscopic debris, so
gently wiping with a soft cloth should remove most
particles.
Figure 1.4: Avoid using non-circular discs
• To keep the laser pickup clean, and don’t touch it.
For the same reason, don’t leave the disc tray opened
unnecessarily.
• Wipe in a straight motion from the inside to the out-
side of the disc. Small dust particles and light stains
will have absolutely no effect on reproduction qual-
ity.
• Music discs with copy control, a copy-protection
system, have been released form several record
companies in an attempt to protect the copyright.
Since some of these discs do not comply with the
CD specifications, they may not be playable on the
DV-RA1000HD.
Figure 1.3: Cleaning discs
TASCAM DV-RA1000HD
ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
1 − Introduction
Never use a stabilizer or printable discs
Using commercially available CD stabilizers or print-
able recordable discs with this player will damage the
mechanism and cause it to malfunction.
NOTE
Never use a disc that has had a stabilizer mounted
to it. The residual adhesive may cause the disc to
stick to the turntable of the unit. If it sticks to the
turntable, you will need a technician to get it out.
Beware of condensation
If the unit (or a compact disc) is moved from a cold to a
warm place, or used after a sudden temperature change,
there is a danger of condensation; vapor in the air could
condense on the internal mechanism, making correct
operation impossible. To prevent this, or if this occurs,
let the recorder sit for one or two hours at the new room
temperature before using.
About CD-R and CD-RW discs
CD-R discs can be recorded once only. Once they
have been used for recording, they cannot be erased or
re-recorded. However, if space is available on the disc,
additional material can be recorded. The packaging of
CD-R discs will include one of the following logos:
There are precautions that you should take when han-
dling CD-R and CD-RW discs.
• Avoid touching the recording (non-label) side of a
disc on which you will be recording. Recording on
a disc requires a cleaner surface than playing back,
and fingerprints, grease, etc. can cause errors in the
recording process.
• CD-R and CD-RW discs are sensitive to the effects
of heat and ultraviolet rays. It is important that they
are not stored in a location where direct sunlight will
fall on them, and which is away from sources of heat
such as radiators or heat-generating electrical devic-
es.
Figure 1.5: CD-R discs
By contrast, a CD-RW disc can be used in much the
same way as a CD-R disc, but the disc can be erased,
and the disc can be re-used for other recordings. The
packaging of CD-RW discs will include one of the fol-
lowing logos:
• Always store CD-R and CD-RW discs in their cases
to avoid dirt and dust accumulating on their surfaces.
• When labeling CD-R and CD-RW discs, always use
a soft oil-based felt-tipped pen to write the informa-
tion. Never use a ball-point or hard-tipped pen, as
this may cause damage to the recorded side.
Figure 1.6: CD-RW discs
• Always keep the recording sides of the discs away
from grime and dust to avoid a reduction in sound
quality. To clean a disc, wipe gently with a soft dry
cloth from the center towards the outside edge. Do
not use thinner, gasoline, benzene or LP cleaning
fluid, as these will damage the disc and cause the
disc unplayable.
However, you should note that an audio CD created
using a CD-RW disc may not play back satisfactorily on
every audio CD player. It will, naturally, be playable on
the unit. This is in no way a limitation of the unit itself,
but of the difference between the different types of
media and the methods used to read them.
• Do not put labels or protective sheets on the discs
and do not use any protective coating spray.
The unit supports normal speed (1x – 4x) and hi-speed
(4x – 10x) discs. It does not support ultraspeed discs
(10x – 24x).
• If you are in any doubt as to the care and handling of
a CD-R and CD-RW discs, read the precautions sup-
plied with the disc, or contact the disc manufacturer
directly.
10
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
1 − Introduction
About DVD R and DVD RW discs
The DV-RA1000HD uses DVD±RW media for digital
audio data recording and storage, and use DVD±R as
media for the archive. DVD-RAM is not supported on
this unit.
If such an error occurs during recording, recording is
interrupted momentarily.
Errors during playback will cause silences to be
momentarily inserted.
As with recordable DVD±RW media can have data
erased, and the whole disc can be erased and reused a
number of times.
Repeated continuous errors will stop playback.
Rewriting limitations
NOTE
Although the theoretical number of times that a
DVD±RW disc can be re-written is 1,000, the actual
number of rewrite operations possible on a disc when
used in the DV-RA1000HD may be significantly less.
This is not a limitation of the DV-RA1000HD. In actual
practice in real-world environments, DVD±RW discs
cannot be rewritten 1,000 times.
Though the unit has been tested with a wide vari-
ety of commercial discs and media, you should be
aware that some discs may contain manufacturing
defects, etc. which make them unsuitable for use
with the unit.
The packaging for rewritable DVD±RW media include
the following logo:
For this reason, to maintain data integrity, TASCAM
strongly recommends the use of new DVD±RW discs
for important recordings.
In addition, before and while editing files on the
DV-RA1000HD, back up the recorded or edited files to
Figure 1.7: DVD RW discs
for more details regarding the use of DVD±RW media
with the unit.
NOTE
Certain brands of disc have been tested with the unit
and are therefore listed as “supported.”
The number of times the current disc has been re-
written can be viewed in the check screen. (See “The
DVD±RW
Ricoh,Verbatim,TDK,Philips,Sony 2x - 6x
DVD±R
Ricoh,Verbatim,TDK,Maxell,Sony 4x - 16x
The use of these discs is strongly recommended in
order to achieve optimum results.
NOTE
• Discs not listed in the list above may not oper-
ate properly on the DV-RA1000HD. If you insert
an unsupported DVD disc in the tray, the unit will
display a popup alarm message on the screen.
If you plan to purchase discs in a bulk, insert a
sample disc into the tray to make sure that the
disc is supported prior to purchase. (See “Using
• The check screen enables you to check wheth-
er a loaded DVD disc is supported by the
DV-RA1000HD. (See “The check screen” on page
Note that dirt or scratches on DVD±RW media can
cause deterioration of recording quality.
TASCAM DV-RA1000HD
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 − Names and functions
Front panel
1
2
3
45 6 7
8 9
0
o
q w e r t y u i
p
a s d f
g
Figure 2.1: Front panel
1 POWER switch
6 ODD key
Turns on and off the power to the DV-RA1000HD.
Sets Drive mode to ODD. (See “Drive mode” on
If you turn off the POWER switch without perform-
ing the shut down operation, the DV-RA1000HD
will automatically perform the shut down process,
then turn itself off. (If you turn off the POWER
switch during the format, copy or other operation,
the unit will perform the shut down process after
the operation is complete.)
7 HDD key
Sets Drive mode to HDD (See “Drive mode” on
8 PHONES control
Adjusts the level of a connected set of stereo head-
phones.
If you turn on the POWER switch before the unit
turns itself off, it will still execute the shut down
process. In this case, turn off the power to the unit
after it completes the shut down operation.
9 PHONES jack
Connect a standard set of stereo headphones here.
0 TIMER switch
2 OPEN/CLOSE key
Turns timer start (power-on playback) on and off.
Opens and closes the disc tray. To shut down the
unit safely, press and hold down this key for at least
one second.
q
w
(
) key
3 JOG/DATA dial
Press the key briefly to select (skip) tracks back-
ward. To perform a backward cue search during
playback or pause, press and hold down this key.
Changes parameter values and moves the cursor in
the menu lists on the screen. In jog playback mode,
use this dial to jog the playback position backward
and forward. To change the LCD contrast, rotate the
JOG/DATA dial while pressing and holding down
the DISPLAY key.
(
) key
Press this key briefly to select (skip) tracks forward.
To perform a forward cue search during playback or
pause, press and hold down this key.
4 MONITOR key
e STOP key
Stops the transport mechanism.
r PLAY key
Starts playback from the stopped position, resumes
Switches between recording source monitoring and
playback monitoring. (See “Monitoring” on page
5 EFFECT key
playback from the paused position, or starts record-
ing from record ready mode.
Turns the effects on and off. To display the effects
screen, press and hold down the key for one second
or longer. (See “Effects” on page 55.)
1ꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
2 − Names and functions
t READY key
p Soft function keys (F1 - F5)
Pauses playback or recording. To use the JOG/DATA
dial to jog the playback position, press and hold
Use the soft function keys to perform the functions
displayed on the bottom row of the screen. The
functions are context-sensitive.
a INPUT LEVEL key
y RECORD key
Displays the input level screen. (See “Adjusting the
Pressing this key while the unit is stopped places
the unit in record ready mode. Pressing this key
while recording divides a recording into tracks
(track increment).
s MENU key
From the home screen, press this key to enter the
menu system and display the main menu.
u MUTE key
d ENTER key
Mutes the playback signal during playback, and
mutes the recording source signal during record-
ing. Short presses are latching: that is, pressing the
key briefly once mutes the signal, pressing the key
briefly again cancels the mute. Long presses are
non-latching: that is, pressing and holding down the
key mutes signals, and releasing the key cancels the
mute.
Confirms the parameter edits or the menu item
selections on the screen. It also adds a carriage
return during character input in the naming pro-
cess.
It also launches the virtual front panel when pressed
from the home screen.
f CANCEL key
i MARK key
Cancels the parameter edits, or selects the upper
menu in the menu hierarchy. While the virtual front
panel (VFP) is displayed, press this key to exit the
VFP and return to the home screen.
Adds a mark at the point where the key was
pressed. Pressing and holding the DISPLAY key
and pressing the MARK key brings up the locate list
screen. (See “About marks” on page 39.)
It is also used to reset the peak hold or as a delete
key during character input in the naming process.
o DISPLAY key
Switches time display mode in the home screen.
g KEYBOARD jack
Connect a computer PS/2 keyboard (US standard
layout) here to name files and projects, and to create
project notes.
TASCAM DV-RA1000HD
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
2 − Names and functions
Remote control unit
k
j
l
;
h
Figure 2.2: Remote control unit
Keys found on only the remote control unit
The CLEAR key is used to clear the current num-
h
/
keys and
/
keys
These are separate keys on the remote control unit,
but are the same key on the main unit (short press
for skip, long for search). (See “Basic playback
l
;
LOCATE key
Displays the locate point list for location and edit-
j
k
A-B key
Enables you to set and perform A-B repeat. Note
that you can set A-B repeat only from the remote
control unit. (See “A-B repeat” on page 31.)
JOG/DATA (+/–) keys
Functions the same as rotation of the JOG/DATA
dial on the main unit, clockwise and counter-clock-
wise.
Number keys and CLEAR key
Enables you to select a track directly by pressing
the number keys, and set a programmed playback.
Keys that features the same functions as those on the main unit
• ENTER MUTE
• REC *2
• STOP PLAY
The following keys function in the same way as those
of the same name on the main unit. For the function
description, refer to the “Front panel” section in the pre-
vious pages.
)
• READY
• MARK
• OPEN/CLOSE
• DISPLAY
• EFFECT
• MONITOR
• MENU
*1) The F1
remote control unit, duplicating one of their most com-
mon functions. The F5 key is labeled as HOME F5 key,
and is often pressed to display the home screen.
-F4 keys are arranged as cursor keys on the
/
• CANCEL
*2) The REC key corresponds to the RECORD key on
the main unit.
• F1 - F5 *1
)
1ꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
2 − Names and functions
Keys that feature the same functions as the switches on the virtual front panel
• FINALIZE
• UNFINALIZE (UNFINAL.)
• ERASE
The following keys function in the same way as the
switches on the virtual front panel on the main unit.
(The key names that differ from those of the switches
on the VFP screen feature additional corresponding
switch names in parentheses.) For the function descrip-
• FADE
• REC MODE (RMODE)
• A.TRACK (ATRK)
• A.READY (ARDY)
• A.CUE (ACUE)
• REPEAT (RPT)
• PGM
• SINGLE (SNGL)
• SYNC REC (SYNC)
TASCAM DV-RA1000HD
1ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
3 − Connections
DSD I/O (SDIF-3
& DSD-raw)
Serial
control
Power
input
Analog I/O (balanced
& unbalanced)
PCM digital I/O
(AES/EBU & S/PDIF)
USB to PC Word sync
connections
RC-RA1000
connection
Figure 3.1: Rear panel connections
Analog audio connections
The DV-RA1000HD can accept and output both bal-
anced +4 dBu nominal and unbalanced –10 dBV nomi-
nal signals.
for balanced connections, and the RCA (pin) jacks for
unbalanced connections.
On playback or monitoring, audio is always output from
both sets of connectors in parallel.
Use the XLR jacks, wired as 1=ground, 2=hot, 3=cold
Digital audio connections
The DV-RA1000HD can accept digital audio data from
one of three sources, each corresponding to a differ-
ent audio format, and can output digital data from the
equivalent type of connector, and in the same format as
it receives data.
In Sampling Frequency 176.4/192 kHz mode, both con-
nectors are used at double speed (double-speed and
double-wire).
S/PDIF These RCA pin jacks are labeled as COAXIAL
on the rear panel. The format is S/PDIF (IEC60958).
AES/EBU Note that while AES/EBUs connections
usually use one XLR connector for a stereo pair, the
DV-RA1000HD is provided with two connectors for
input and output.
These jacks can accept and transmit data at Sampling
Frequency 44.1/48 kHz mode or at Sampling Frequency
88.2/96 kHz mode.
SDIF-3/DSD-raw These BNC connectors accept and
output digital audio data in SDIF-3 (DSD-Raw) format.
Each connector carries one channel of the stereo pair.
NOTE
Strictly speaking, the format used by these connec-
tors is called IEC-ꢄ0ꢇꢃꢆ-ꢂ, or AES-ꢁ-1ꢇꢇꢀ.
CAUTION
When working in Sampling Frequency 88.2/96 kHz
mode, there is an option of either using one XLR con-
nector at double speed (double-speed), or two connec-
tors, each at normal speed (double-wire). If only one
XLR connector is being used, connections should be
made only to XLR connector 1 (input and output).
When using DSD connections, all digital audio units
in the system, including the DV-RA1000HD, must
be synchronized to a common clock signal. On the
DV-RA1000HD, if this signal is external, a ꢂꢂ.1 kHz
signal should be supplied at the WORD SYNC IN ter-
minal. Alternatively, the DV-RA1000HD can be set
to act as the system clock master, at ꢂꢂ.1 kHz, with
the DSD audio source acting as the clock slave. (See
1ꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
3 − Connections
Other connections
WORD SYNC The DV-RA1000HD is fitted with three
CONTROL I/O You can use RS-232C serial control
with the DV-RA1000HD by connecting an appropriate
cable to this connector. Consult your TASCAM distrib-
utor for details of pin-outs, protocols, etc.
BNC connectors for standard word sync.
CAUTION
There should be one, and only one clock master in
a setup.
REMOTE IN Connect only the supplied wired
RC-RA1000 remote control unit to this jack. Since the
remote control unit is a wired unit, the DV-RA1000HD
will respond to the key presses on the remote control
unit precisely. It does not require any batteries, and you
do not need to point at the DV-RA1000HD for opera-
tion.
IN receives word sync from an external source, and
OUT is used when the DV-RA1000HD is used as the
word sync master in a setup, outputting the frequency
of the current project. THRU echoes the sync received
at IN and is terminated automatically if nothing is con-
nected.
PHONES Connect a standard set of stereo headphones
to this front panel 1/4" jack. Adjust the level with the
control above the jack.
NOTE
When in DSD recording mode, the DV-RA1000HD
inputs and outputs word sync at ꢂꢂ.1 kHz. Under
these conditions, the input sync can be ꢄ% away
from the norm.
KEYBOARD (front panel) Connect a computer
PS/2 keyboard (US standard layout) to this jack located
on the right side of the front panel to name files and
projects, and to create project notes.
USB Connect a suitably-equipped computer using a
USB 2.0 cable. The DV-RA1000HD appears as a mass
storage device, requiring no driver software.
USB connection enables you to transfer audio files on
the HD of DV-RA1000HD to the computer, and transfer
audio files on the computer to the DV-RA1000HD. (See
TASCAM DV-RA1000HD
1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
HDD and ODD
Drive mode
The DV-RA1000HD is equipped with a DVD drive and
hard disk drive. Since a DVD drive plays optical discs,
such as CDs and DVDs, it is referred to as an “ODD
(Optical Disc Drive)” in this manual. The hard disk
drive is referred to as “HDD (Hrad Disc Drive).”
you cannot use the ODD (excluding opening and clos-
ing of the disc tray).
When you press the ODD key in HDD mode, the
DV-RA1000HD will save the current project in the HD,
then switch to ODD mode. When you press the HDD
key while operating a DVD disc in ODD mode, the
DV-RA1000HD will perform the Save UDFMI func-
tion, then switch to HDD mode.
The DV-RA1000HD enables you to switch between
ODD mode and HDD mode.
In ODD mode, you cannot use the HDD. In HDD mode,
Storage media
The DV-RA1000HD enables you to record data on the
internal HD, or to various optical discs, such as CD-R,
CD-RW, DVD-R, DVD+R, DVD-RW, and DVD+RW.
The functions available with these discs vary depend-
ing on the type of media. For example, some types of
discs are writable, and some are not. Some are rewrit-
able, and some are not. Select an appropriate disc to
suit your purpose. There are also different disc formats,
depending on the type of media. However, any format
is compatible with Windows and Macintosh computers.
NOTE
The files recorded in DVD+RW discs using this unit
can be played back on the Tascam DV-RA1000.
Also, the files recorded on DVD+RW discs using the
DV-RA1000 can be played back with this unit.
DVD+R and DVD-R
Use these discs when you wish to duplicate project
data recorded on the unit HD. They are suitable for
archiving materials recorded with the DV-RA1000HD.
Note that data can be written in copy mode, but not
recorded directly.
Internal HD
The HD of DV-RA1000HD enables you to record audio
data that is compatible with computer-based digital
audio workstations. You can select 44.1/48 kHz, 88.2/96
kHz, 176.4/192 kHz and 24-bit. The DSD format
recording is available, too. You can also write data to
the HD using copy mode, or record data directly.
The written data cannot be edited; that is, you cannot
edit the files or change the markers.
The disc format is ISO9660.
CD-R and CD-RW
You can directly record audio CD in CD-DA format.
Furthermore, you can add recordings as long as the
disc is not finalized. You can also delete or unfinalize
data on CD-RW discs, which enables you to record data
repeatedly.
The hard disk format is FAT32.
DVD+RW and DVD-RW
These discs also enable you to record audio data that is
compatible with computer based digital audio worksta-
tions. You can also write data to the HD using copy
mode, or record data directly.
During the direct recording of these discs, the
DV-RA1000HD functions as a standard CD recorder
that features synchronized recording and other func-
tions. You can, of course, play store-bought audio CDs
using the DV-RA1000HD.
The disc format is UDF1.5. When you eject a disc or
shut down the DV-RA1000HD, the disc drive writes
the UDF management information (required for the
DV-RA1000HD to read information on the disc) to the
disc.
Furthermore, you can create audio CDs from audio
tracks stored on the unit’s HD, or copy audio from
audio CDs to the HD.
You must perform the “close” operation when using a
DVD-RW disc on the DV-RA1000HD to enable your
computer to read data from the disc.
1ꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Shut down
In order to shut down the DV-RA1000HD safely with a
disc loaded, follow the steps below.
that you can turn off the DV-RA1000HD using
the POWER switch.
NOTE
NOTE
During the shut down process, the DV-RA1000HD
If you turn off the POWER switch without perform-
ing the shut down operation, the DV-RA1000HD
will automatically perform the shut down process,
then turn itself off. (If you turn off the POWER switch
during the format or copy operation, the unit will
perform the shut down process after the format or
copy operation is complete.)
If you turn on the POWER switch before the unit
turns itself off, it will still execute the shut down
process. In this case, turn off the power to the unit
after it completes the shut down operation.
1
With a disc loaded, press and hold the OPEN/
CLOSE (SHUT DOWN) key for at least a second.
2
A popup menu appears. Press ENTER to do shut-
down, or CANCEL to return (if you pressed the
OPEN/CLOSE key accidentally for a long time, for
example).
3
All front panel controls are disabled. When it has
finished, a popup message appears telling you
LCD screens
The DV-RA1000HD LCD panel enables you to view
the status of the recorder, set the menu parameters,
make the switch settings, and set up the effects.
Menu screens
The menu screens enable you to set up the system, proj-
ects, discs, copy functions, and other functions. Press
Home screens
The “home” screens display current information
regarding the mode and status of the recorder. There
are two types of home screens, depending on whether
a CD-R/CD-RW disc or DVD±RW/HD is being used.
These screens are view-only and non-editable. You can
access the screens assigned to the switches by pressing
the function keys. (See “The “home” screen” on page
Virtual front panel (VFP)
The virtual front panel allows access to various switch-
es on the screen that are not accessible on the front
panel. Press the ENTER key from the home screen to
display the virtual front panel. (See “The virtual front
Other screens
The DV-RA1000HD also features special screens for
effects settings, input level settings, and the locate list.
You can recall these screens by pressing dedicated keys.
Navigating the screens
•
A typical screen on the DV-RA1000HD
features five switches on the bottom. Press
•
•
Use the JOG/DATA dial to adjust a value or
setting.
one of the function keys (F1 F5) to execute
-
Press the ENTER key to confirm a setting or
selection in the screen.
a function or open a screen assigned to the
corresponding key.
•
Press the F1 or F2 key (up/down) to select an
item in the screen.
Adjusting the display contrast
To adjust the display contrast:
NOTE
You cannot use the JOG/DATA keys on the remote
control unit to adjust the display contrast.
While pressing and holding the DISPLAY key, turn the
JOG/DATA dial to adjust the contrast to suit your light-
ing and viewing angle.
TASCAM DV-RA1000HD
1ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
The“home” screen
The DV-RA1000HD has two types of “home screen”,
depending on whether a CD or DVD±RW/HD disc is
being used.
TIP
These screens are often accessible from other
screens by pressing the F5 key (which is then
marked as HOME on the display).
“Home” screen content
The home screens are view-only and non-editable.
However, you can access the screens assigned to the
switches by pressing the corresponding function keys.
3
4
5 67
12
123
4
5 67
0
89
q
we
Figure 4.2: The CD home screen
0
w
er
89
q
1
2
3
4
5
6
7
8
9
0
q
w
e
Input mode
Digital I/O
Figure 4.1: DVD RW/HD home screen
Reference clock
Meter
1
2
3
4
5
6
7
8
9
0
q
w
e
r
Input mode
Digital I/O
Disc type
Reference clock
Disc status
Meter
Audio format
Disc type
Track number
Disc status
Track time
Audio format of the current project
Name of the current project
Name of the current file
Display mode of track time
Current track number
Time display of the currently-playing track
Playback mode (single, program, repeat)
Short-cut function (assignable)
Track time display mode
CD text information
Playback mode (single, program, repeat)
Short-cut function (assignable)
ꢀ0
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Menu operations
Change values and highlight
options with the dial
Confirm
settings or go
down a level
Use the soft function keys to perform
the functions on the bottom row of
the screen (often used as cursor keys)
Enter the
Go up a
menu system
level
Figure 4.3: Using the DV-RA1000HD menu system
To enter the main setting menu of the DV-RA1000HD:
•
CANCEL returns up a screen
•
When the F5 key is labeled as HOME on the
on-screen label, pressing it returns to the
home screen.
1
2
Press the MENU key. The main menu appears.
Use the JOG/DATA dial or the F1 and F2 keys on
the unit, or the JOG/DATA keys on the remote
control unit, to select (highlight) a desired menu
item.
NOTE
Note that the menu system cannot be accessed
while the unit is recording and many operations
cannot be carried out while playing back.
We suggest that you pause or stop playback before
trying to enter the menu system.
3
Press ENTER to enter the selected menu item.
Also use the ENTER key to confirm the settings of
a screen. Pressing ENTER on a screen with many
settings will confirm all these settings at once,
and return to the previous menu level.
TASCAM DV-RA1000HD
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Menu tree
HOME
MAIN
SYSTEM SETUP
PROJECT
I/O SELECT
REFERENCE
CLOCK
CALENDAR
CREATE
CHECK
PROJECT LIST
PROJECT TEXT
version check
battery check
medium check
FILE LIST
PLAY LIST
EDIT
COPY ID
PREFERENCE
FORMAT
DISC
COPY
VFP
PROGRAM
FADE TIME
PLAY
REC
CD
etc
AUTO TRACK
SOUND LEVEL
PITCH CONTROL
OSC
INPUT LEVEL
LOCATE LIST
EFFECT
EQ LIBRARY
EQUALIZER
DYNAMICS(BAND)
DYNAMICS(TOP)
DYN LIBRARY
Figure 4.4: Menu tree
ꢀꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
The virtual front panel (VFP)
The DV-RA1000HD allows access to many functions
through the virtual front panel, providing a graphical
representation of many of the keys and controls that
might be hardware switches on other units.
Each panel features the switches to which various
functions are assigned.
3
Rotate the JOG/DATA dial to select a switch in the
panel.
Note that many of these functions are hardware keys on
the remote control unit.
4
Use the F5 (PUSH) key or ENTER key to press the
selected switch.
If a switch just toggles between on and off, a
mark appears above the switch when the switch
is turned on, and a mark appears above the
switch when the switch is turned off.
To launch the virtual front panel
1
From the home screen, press the ENTER key.
The virtual front panel appears.
There are four types of the virtual front panel:
“PLAY”, “REC”, “CD”, and “etc.”
NOTE
• In this manual, the procedure of selecting a
switch in the virtual front panel and pressing the
F5 key is referred to as “pressing a switch.”
•
Press CANCEL to exit the virtual front panel
and return to the home screen.
• Some switches, when pressed for at least one
second, present a menu of choices, but others
just toggle between on and off.
2
Press the function key (F1 - F4) that corresponds
to the tab on the bottom of the screen to display
the desired panel.
Play page
ARDY (auto-ready) Is used to switch auto-ready play-
back mode on and off. (See “Auto ready” on page 32.)
SNGL (single) Turns single-track playback mode on and
NOTE
The single play function cannot be used with the
repeat function. If either the single play or repeat
function is enabled, it is disabled when the other
function is enabled.
Figure 4.5: Virtual front panel (PLAY)
Figure 4.6: Virtual front panel (REC)
Figure 4.7: Virtual front panel (CD)
Figure 4.8: Virtual front panel (etc.)
ACUE (auto-cue) Turns the auto-cue function on and
RPT (repeat) Sets the playback repeat mode between
OFF(off), ALL(all tracks of the disc are repeated)
ASPC (auto-space) Turns the auto-space function on
PGM (program) Turns programmed playback on and
off, and allows setting of the programmed playback
Rec page
ATRK (auto-track) Turns the auto track function on
and off when recording. (See “Auto track increment” on
TASCAM DV-RA1000HD
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
RMODE (recording mode) Switches the PCM DVD/
HDD recording mode between “normal” and “over
write” modes. (See “Recording mode” on page 45.)
Etc. page
MONO Turns mono monitoring on and off (except the
DSD mode).
SYNC (sync rec) Sets the synchronized recording func-
tion to off, rehearsal, or on. (See “Synchronized record-
NSD (noise-shaped dithering) Allows dithering to
be turned on and off (only when recording CDs).
PITCH (pitch control) Turns the pitch control on and
off. Pressing this switch for at least one second brings
up the pitch change setting screen. (See “Pitch change”
CD page
FINALIZE Finalizes CD-R and CD-RW discs, writing the
TOC, and allowing them to be played on regular play-
OSC (oscillator) Turns the oscillator output on and off.
Pressing this switch for at least one second brings up
the oscillator screen. (See “Oscillator” on page 37.)
UNFINAL. (unfinalize) Removes the TOC from CD-RW
discs, allowing further recording on them. (See
ERASE Erases all tracks from CD-RW discs.
General preferences
There are a number of preferences that can be applied
to the DV-RA1000HD in order to help adapt the unit to
your working style.
Calendar display (CALENDAR) You can select
M/D/Y(month/date/year) or Y/M/D(year/month/
date) for the date format shown in the calendar screen.
1
Press the MENU key, and use the JOG/DATA dial
to select SYSTEM SETUP. Press ENTER.
Time zone (TIME ZONE) allows you to set up your local
time zone (expressed relative to GMT). This may be
useful if the discs containing your files are moved to
different time zones.
2
Use the JOG/DATA dial to select PREFERENCE. Press
ENTER.
Reference level (REF.LEVEL) This is the amount of
headroom from the digital saturation level (0 dB) to the
analog nominal level.
This setting applies only to the balanced XLR analog
I/O jacks (and not to the unbalanced RCA analog con-
nectors).
You can select from the following five reference levels.
Reference level Nominal level
Maximal level
+15dBu
–9dB
–14dB
–16dB
–18dB
–20dB
+6dBu
+4dBu
+4dBu
+4dBu
+4dBu
Figure 4.9: The preference screens
+18dBu
+20dBu
3
4
Use the F1 through F4 keys as cursor keys to nav-
igate around the screen, and the JOG/DATA dial
(except for the short cut parameter) to change
the highlighted parameter, as detailed below.
+22dBu
+24dBu
Table 4.10: Reference level
Press ENTER to return to the system setup menu
after changing the settings.
Resume playback (RESUME) The DV-RA1000HD can
be set to resume playback or recording from the point
where it stopped when the STOP key is pressed.
Meter release (METER RELEASE TIME) This parameter can
be set to Slow, Mid, or Fast.
This point is retained even when the unit is powered
off. Select either ONor OFFfor this option.
Meter hold time (PEAK HOLD) This parameter can be
set to OFF, 1 or 2 seconds (1sor 2s) or HOLD, in
which the peak reading is held until this parameter is
reset.
TIP
You can press STOP and the
key together to
return to zero.
ꢀꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
NOTE
you are connecting to the PS/2 connector on the
DV-RA1000HD. Select either US(101-key (US) key-
board) or JPN(106-key (Japanese) keyboard).
This function also works when recording.
LCD brightness (LCD BRIGHTNESS) You can adjust the
brightness of the LCD backlight in the range of 1
through 6. The LCD backlight will be brighter with
higher values.
DSD seamless play (DSD SEAMLESS PLAY) This param-
eter turns DSD seamless playback ONand OFF.
A DSD file recorded on the DV-RA1000HD includes
a small silent portion at the beginning of the file. The
DSD seamless playback function will skip the playback
of this silent portion.
Keyboard type (KEYBOARD TYPE) This param-
eter enables you to specify the type of keyboard
Short cuts for screen access
You can assign menu items (that are commonly-
accessed from the home screen) to the function keys (F1
- F5).
3
4
Using usual menu navigation technique, select a
menu item from the left column you wish to as-
sign to one of the function keys as a short cut. (See
The following menu items have been assigned to the
function keys as the default settings:
Press the function key (F1 - F5) to which you wish
to assign the selected menu item.
F1: I/O select
The right part of the screen will be updated to
display the menu title as a new assignment.
F2: Reference clock
F3: Calendar
NOTE
F4: Preferences
If you change the mind and you do not want to as-
sign the menu item to the function key, press and
hold the function key for at least one second.
F5: Save UDF management information
Follow the steps below to set up the short cuts:
5
Press and hold the ENTER key for at least one
second.
1
Press the MENU key to display the main menu.
The setting is confirmed, and the short cut as-
signment list on the right column disappears.
The DV-RA1000HD returns to a normal menu
screen.
To cancel the short cut settings, press the CANCEL
key for at least one second, instead of the ENTER
key.
The settings is cancelled, and the short cut as-
signment list on the right column disappears. The
DV-RA1000HD returns to a normal menu screen.
Figure 4.11: Main menu
2
Press the F3 (S.C.) key.
The left part of the screen shows the menu sys-
tem, and the right part shows the current short
cut assignments of the five function keys. (Blank
for unassigned keys.)
Figure 4.12: Main menu (with short cut)
TASCAM DV-RA1000HD
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Clock/calendar
The DV-RA1000HD contains a battery-powered clock/
calendar which timestamps all files recorded on a
DVD/HD disc. These timestamps are not visible from
the DV-RA1000HD, but may be viewed as part of the
file metadata when the unit is connected to a computer.
The currently-set date is shown in “military”
(year/month/day) format, as above or in US/Jap-
anese format (month/day/year) format.
“Calendar display” on page 24.) Also note the
time zone setting in the preferences, which allows
you to compensate for time differences if your
project crosses to another time zone for master-
ing, etc. (See “Time zone” on page 24.)
Setting the clock follow these steps:
1
From the home screen, press the MENU key and
select SYSTEM SETUP. Press ENTER.
3
Use the cursor keys to navigate around the fields,
and the JOG/DATA dial to change values.
2
Select CALENDAR and press ENTER.
Figure 4.13: Editing the clock settings
The check screen
The check screen enables you to view the
•
Press the F2 (BATTERY) key to view the battery
DV-RA1000HD firmware version, the level of the inter-
nal battery, and the status of the loaded DVD disc.
level.
The battery should last for several years
from the date of purchase. Contact your
TASCAM distributor if the battery check
screen indicates “NEED TO CHANGE”
or “EMPTY.”
1
From the home screen, press the MENU key.
The main menu appears.
2
3
Select SYSTEM SETUP, then press ENTER.
Select CHECK, then press ENTER.
The check screen appears.
4
Press a function key to which the information
screen you wish to view is assigned.
•
Press the F1 (VERSION) key to view the firm-
ware version numbers.
Figure 4.15: Battery level
The screen lists (from the top) the
•
Press the F3 (MEDIUM) key to display the media
information.
DV-RA1000HD firmware version number,
firmware build number, and the internal
drive firmware version number.
The screen indicates the support information
regarding the currently-loaded DVD disc
and the number of rewriting operations car-
ried out on the disc.
Figure 4.14: Firmware version numbers
Figure 4.16: Media information
ꢀꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Selecting the input source
The input source for recording can be selected as
described here:
If you are recording to a 176.4/192 kHz-sampling
frequency DVD and HD, this option is not avail-
able, and AES/EBUis the only option available.
1
2
3
Press the MENU key, and use the JOG/DATA dial
to select SYSTEM SETUP. Press ENTER.
If you are recording to a DSD DVD and HD, the
signals will always be input and output through
the BNC connectors. The DIO parameter here
chooses the format in which the audio is sent and
received: DSD-RAW, which is the raw DSD bit
stream, or SDIF-3(no other options are avail-
able). Consult the documentation for your other
equipment to find out what format is most suit-
able for your setup.
Use the JOG/DATA dial to select I/O SELECT. Press
ENTER.
Use the JOG/DATA dial to select from the follow-
ing screen:
6
Finally, in the case of 88.2/96 kHz-sampling fre-
quency DVD and HD with AES/EBUselected
as the input/output connector, there is an option
to select double-wire or double-speed as the I/O
format (MODE).
Figure 4.17: Selecting the input source
The COAXIALoption allows double-speed
mode only, and 176.4/192 kHz-sampling fre-
quency is double-speed + double-wire mode, and
cannot be changed.
4
5
First, choose between ANALOGand
DIGITALon the INPUT parameter.
If you choose the analog option, remember that
both the balanced XLR inputs and the unbal-
anced RCA inputs are active together, but you
should only use one set.
7
Press ENTER to confirm your settings and return
to the system setup menu.
TIP
If you are recording to CD, or a 44.1/48 kHz or
88.2/96 kHz-sampling frequency PCM DVD and
HD, select the DIO parameter (digital I/O) as ei-
ther AES/EBUor COAXIAL(S/PDIF). The
appropriate digital terminals will also be used for
output of the digital signal.
The DV-RA1000HD is not equipped with a sampling
rate converter.
If you set the INPUT parameter to DIGITAL, in-
put a signal with a sampling frequency of ꢂꢂ.1 kHz
for CD recording. For DVD RW or HD recording in
PCM mode, input a signal with the same sampling
frequency as that for the project.
44.1/48 kHz
88.2/96 kHz
176.4/192 kHz
CD-R/RW
DSD DVD/HD
Sampling frequen- Sampling frequen- Sampling frequen-
cy DVD/HD
COAXIAL / AES/EBU COAXIAL / AES/EBU COAXIAL / AES/EBU AES/EBU only
n/a n/a COAXIAL – Double-speed +
cy DVD/HD
cy DVD/HD
SDIF-3 or RAW DSD
n/a
DIO
double-speed only double-wire only
MODE
AES/EBU –
double-wire or
double-speed
Table 4.18: Digital input source options
The selected input is shown on the home display.
TASCAM DV-RA1000HD
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Adjusting the input level
The input level is adjustable for all inputs (analog or
digital), regardless of the current selection.
2
Use the F3 and F4 keys to move between the MAIN
(input level), BALANCE (between left and right) and
BYPASS sections of the display.
The balance between the left and right channels of the
input may also be set.
Use the JOG/DATA dial to adjust the settings,
including the bypass setting.
For optimum sonic quality, it is also possible to bypass
the input level and balance circuitry.
TIP
• Use the F1 key to reset the input level to unity
gain, and the F2 key to center the balance set-
ting.
1
Press the INPUT LEVEL key to bring up the input
level screen:
• You can adjust the analog input level to one of
the ꢄꢇ stages in the range of –∞ through +1ꢀ dB,
and the digital input level in steps of 0.ꢃ dB in the
range of –10 dB through +10 dB.
3
Press ENTER when finished.
NOTE
• When the signal on playback or recording is at –
0.1ꢁ dBFS or over for more than one sample, the
OVER indicator on the meter lights. If a track is
normalized to –0.1 dB (for example) on a DAW be-
fore recording at unity gain on the DV-RA1000HD,
the OVER indicators may therefore light, even
though there is no clipping taking place.
Figure 4.19: Input level settings
• You can set the meter release time and peak hold
mode in the preference screen. (See “General
To reset the peak indication, press the CANCEL
key while the home screen is displayed.
Selecting the reference clock
As mentioned earlier, only one clock sync source
should be available within a system.
3
Use the JOG/DATA dial to select the clock source
(SOURCE):
The current clock selection is always shown on the
home display.
• Internal—the DV-RA1000HD acts as the
clock master.
To select the clock source for the DV-RA1000HD:
• Word—the clock sync is received from the BNC
WORD SYNC IN connector.
1
Press the MENU key, and use the JOG/DATA dial
to select SYSTEM SETUP. Press ENTER.
• Digital IN—the clock is received from the
currently selected digital audio input source.
2
Use the JOG/DATA dial to select REFERENCE CLOCK.
Press ENTER.
NOTE
You cannot select Digital INif the
DV-RA1000HD is playing or recording a project in
DSD mode.
4
Press ENTER to confirm the setting and return to
the system setup menu.
Figure 4.20: Word sync selection
ꢀꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
4 − Basic operations
Naming files, projects, marks, etc.
Use the JOG/DATA dial to scroll through the set of cur-
rently available characters.
Using a keyboard When recording on DVD, the
easiest way to name files (see “Renaming a file” on
“Adding notes to a project” on page 43), etc. is using
a computer PS/2 keyboard (US standard layout) con-
nected to the front panel of the DV-RA1000HD.
The available character sets are changed using the:
CAPS: all UPPERACASE letters from A
through Z, space and symbols
small: lowercase letters from athrough z,
space and symbols
WARNING
Do not connect or disconnect such a keyboard to
or from the DV-RA1000HD with the power turned on
as this may damage the DV-RA1000HD or the key-
board.
NUM:
digits from 0through 9, space and
symbols
Move backwards and forwards using the F3 and F4
keys. Press ENTER when done.
Basically, you can use this keyboard in the usual way.
NOTE
Start editing titles with the keyboard by pressing the
keyboard’s left or right cursor key (or F3 or F4 on the
DV-RA1000HD).
The following symbols and punctuations are not
available for names:
* / : < > ? | .
Finish by pressing the keyboard’s [Enter] key.
Adding project notes Notes are done in the same
way, except that here there are no character sets which
can be selected, and punctuation, etc. is available.
NOTE
You may experience a few small incompatibili-
ties with punctuation symbols, etc. if you use a
keyboard that does not conform to the standard
101-key US layout (or the Japanese 10ꢄ-key layout).
The arrow keys act as cursor keys to navigate around
the text block.
Use the ENTER key to add carriage returns and the
CANCEL key as a delete key.
Working without a keyboard However, if such a
keyboard is not available, you can use the front panel to
name disc items.
Use the JOG/DATA dial to scroll through the numbers,
punctuation characters and uppercase and lowercase
letters available for the text.
When a screen allowing you to name an item (project
or file) is shown on the display, highlight it so that it is
shown in inverse video.
Note that the text can contain more lines than the size
of the screen, and can be scrolled up or down.
Press the F4 (right) key to start the naming process.
When you’ve finished entering text, press and hold the
ENTER key for about a second to confirm the entry
before writing it to disc. (See “Writing the UDFMI” on
Alternatively, press and hold the CANCEL key for at
least one second to cancel the edits and return to the
previous screen.
TASCAM DV-RA1000HD
ꢀꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
DVD RW
HD
Basically, the DV-RA1000HD works in the normal way
as a CD player and in a very similar way to many CD
recorder.
However, there are a number of features that may not be
immediately obvious.
tively. Functions marked with a
or
are
available for DVD±RW or HD recording respectively.
refers to both DVD±RW and DVD±R, and
refers to the HD of DV-RA1000HD.
DVD
HD
Certain functions are not available in DSD mode, and
this is noted in the corresponding sections.
DVD
HD
Functions marked with a
or
indicator in this
chapter are available for DVD or HD playback respec-
Playback
The following apply when the DV-RA1000HD is used
to play back CD, CD-R or CD-RW discs. Many of these
features also apply to playback of DVD and HD record-
ed on the DV-RA1000HD.
DVD HD
Basic playback operation
The transport keys enable you to play a disc as if you
were using a standard CD player.
MUTE key again to unmute the signal. Press
and hold the MUTE key to mute the signal
until you release the key. Release the MUTE
key to unmute the signal. While the signal is
muted, the MUTE key indicator lights up.
•
To start playback, press the PLAY key while
the transport section is stopped or playback
is paused.
•
•
To skip the tracks backward or forward,
press the keys.
•
•
To stop playback, press the STOP key.
/
To pause playback, press the READY key.
To resume playback after the playback is
paused, press the PLAY key.
To perform cue search during playback,
press and hold the keys on the front
panel or the keys on the remote con-
/
/
•
To mute the playback signal (i.e., silent play-
back), press the MUTE key. Press the MUTE
key briefly to mute the signal. Press the
trol unit. You will hear an intermittent fast
playback sound at a very low volume.
DVD HD
Display
Use the DISPLAY key on either the main unit or the
RC-RA1000 remote control unit to cycle through track
elapsed time, track remaining time, total elapsed time,
and total remaining time (on playback).
While recording, track elapsed time and recording
remaining time are the only options available.
In stopped mode, the choices are track elapsed time,
track remaining time, total time, total remaining time
(and recording remaining time on recordable discs).
DVD HD
Programmed playback
To program the order of track playback, use the pro-
gram list accessible from the Virtual Front Panel. (See
key on the remote control unit can also be used to
access this screen and turn programmed playback on
and off.
The order of programmed playback is not stored when
power is turned off.
Figure 5.1: Programmed playback
•
•
Use the JOG/DATA dial to scroll through the
list of tracks at the left of the screen.
When programmed playback is turned on, the screen
shows a list of tracks which can be edited as follows:
Add tracks to the end of the program list
using the F1 (ADD) key.
ꢁ0
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
NOTE
•
•
Delete the last track in the program list
using the F2 (DEL) key.
• If you turn programmed playback on while the
recorder is in playback ready mode or playing, a
track set to “ready” in the program list or a track
that is currently playing will be automatically reg-
istered in the program list.
If you turn programmed playback mode on while
the recorder is stopped, no track will be regis-
tered in the program list.
• If you press the STOP key while programmed
playback mode is on, the first track on the pro-
gram list will enter playback ready mode.
• If you press the ENTER key while the program
screen is displayed and no track has been yet
registered in the program list, programmed play-
back mode will be turned off.
• During playback, you cannot delete any tracks in
the program list using the F2 (DEL) key.
• Pressing the CANCEL key while the program
screen is being displayed will delete the regis-
tered program and programmed playback mode
will be turned off.
Confirm the playback order and return to
the previous screen using the ENTER key or
F5 (HOME) key (if this screen was entered using
the RC-RA1000, the home screen is shown).
•
•
You can also use the remote control unit key
equivalents to perform these operations as
well as the number keys for direct program-
ming.
When programmed playback mode is on,
pressing the PGM switch on the play page of
the virtual front panel or the PGM key on
the remote control unit briefly to turn pro-
grammed playback off. Pressing the PGM
switch or PGM key for at least one second
brings up the program screen.
DVD HD
Repeat playback
Use the Virtual Front Panel (see “The virtual front
single-track and whole disc repeat (and off).
A-B repeat Use the A-B key on the remote control
unit to set the A and B points (these must be within the
same track). The first press sets the A point, the next
press sets the B point, and a third press cancels the
loop. Setting a point in another track clears the previous
settings.
NOTE
The repeat function cannot be used with the single
play function. If either the single play or repeat
function is enabled, it is disabled when the other
function is enabled.
Press the STOP key to cancel the A-B repeat function.
The remote control unit’s REPEAT key also allows these
choices, but the RC-RA1000 also adds an A-B repeat
loop.
DVD HD
Single track playback
When the SNGL switch is turned on from the vir-
tual front panel, or using the SINGLE key of the
RC-RA1000, the DV-RA1000HD plays to the end of the
current track only, and then stops playback.
NOTE
This function cannot be used together with repeat
playback.
DVD HD
Auto space playback
When the ASPC switch is turned on from the virtual front
panel, the DV-RA1000HD inserts a gap of two seconds
between tracks when playing back a disc.
This can be useful when recording to an analog tape
deck which can use these silences to detect track divi-
sions.
TASCAM DV-RA1000HD
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
DVD HD
Jog playback
You can use the JOG/DATA dial to jog the playback
position backwards and forwards.
Press the STOP key to stop playback and
cancel the jog mode. If the resume function
has been turned on, playback is stopped at
the point at which you pressed the STOP key.
Press the PLAY key to resume normal play-
back from that point.
•
Press and hold the READY key and press the
PLAY key.
•
Both keys flash. You can now use the
JOG/DATA dial to move the play position back
and forwards through the current track/file.
•
You can also use the JOG/DATA keys on the
RC-RA1000 remote control unit as jog keys.
•
Press the READY key alone to exit from the
jog mode, and leave the playback position at
the position selected with the JOG/DATA dial.
NOTE
This feature cannot be used in DSD mode.
DVD HD
Pitch change
This is another VFP function (see “The virtual front
panel (VFP)” on page 23) for playback only.
The reference clock must be set to the internal clock for
this feature to operate.
Move the cursor to the PITCH switch and press ENTER
briefly to turn on pitch change.
Figure 5.2: Pitch control
Press and hold ENTER for about a second to enter the
pitch change setting screen:
Use the F1 and F2 keys to navigate, and the JOG/DATA
dial to set the value of the pitch (and speed) up to ±6%
away from nominal.
Press ENTER to make the setting.
DVD HD
Auto cue
When the auto cue function is turned on, cueing the
playback position to the beginning of a track will locate
and pause at the first point in the track at which the
audio rises, rather than the top of the track. “The point
at which the audio rises” refers to the first point in a
track at which the audio signal rises above the speci-
fied threshold. (See “Setting the sound threshold level
NOTE
• Note that this function is not available on DVDs
recorded in DSD mode.
• If the audio signal in a track does not exceed
the specified threshold level, the top of the track
will be located and the transport section will be
paused.
Use the Virtual Front Panel (see “The virtual front
control unit’s A.CUE key to turn this function on or off.
This feature can be used together with the auto ready
function. (See “Auto ready” below.)
DVD HD
Auto ready
This automatically cues up the playback position to the
start of the next track after a track has been played and
puts the DV-RA1000HD into the ready position (the
READY key lights).
It can be combined with the Auto cue function (see
“Auto cue” above) to position the playback at the start
of the recorded material.
NOTE
This feature can also be used with DVD playback.
ꢁꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
DVD HD
Fades
It is possible to create linear fades in and out when
playing back.
To display the fade time screen, press for at least one
second the FADE switch on the play page of the virtual
front panel, or the FADE key on the remote control unit.
Use the F1 and F2 cursor keys and the JOG/DATA dial
to set these values (between 0 seconds and 24 seconds).
Figure 5.3: Setting fade times
Fade times are set independently for fade-in and fade-
out operations.
•
•
When playback starts and fade mode is
selected, a fade-in starts.
Press ENTER to confirm the fade time settings.
When playback stops (with the STOP key)
and fade mode is selected, the fade-out
starts. If the STOP key is pressed during the
fade, playback stops immediately.
DVD HD
Timer start
The TIMER switch besides the transport keys on the
front panel allows the DV-RA1000HD to start playback
of the loaded disc automatically when power is sup-
plied.
the whole disc or single track are memorized when the
power is turned off and on again, but the A-B mode and
the A and B points are not memorized.
If the DV-RA1000HD is in ODD mode or in HDD
mode with a disc already loaded, the unit plays the proj-
ect that was open prior to the last shut down, or from
the last position if resume playback is selected. (See
CAUTION
When using this function, remember to shut down
the unit properly (see “Shut down” on page 1ꢇ)
before turning off the power, to avoid possible data
loss.
Recording
The following functions are available when recording to
CD-R or CD-RW. Many are also available when record-
ing to DVD±RW or HD.
DVD RW HD
Basic recording operation
The transport keys enable you to record discs as if you
were using a standard recorder.
the calibration is complete, the READY key
indicator lights up and the unit enters record
ready mode.
1
Press the RECORD key (REC key) while the trans-
port section is stopped or playback is paused to
place the DV-RA1000HD in record ready mode.
NOTE
Optical power calibration adjusts the laser power in
accordance with the characteristics of an inserted
disc so that data can be recorded at optimum qual-
ity.
The RECORD key and READY key indicators light
up.
The DV-RA1000HD switches monitoring mode
to input signal.
2
Press the PLAY key to start recording.
The RECORD key and PLAY key indicators light
•
When you insert a brand new disc into the
disc tray and press the RECORD key, the
DV-RA1000HD automatically performs opti-
cal power calibration (OPC). During the cal-
ibration, the RECORD key indicator lights up
and the READY key indicator flashes. When
up.
•
To stop recording, press the STOP key.
•
To mute recording (that is, recording a silent
part), press the MUTE key. Press the MUTE
key briefly to mute recording. Press the
TASCAM DV-RA1000HD
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
MUTE key again to unmute recording. Press
and hold the MUTE key to mute the signal
until you release the key. Release the MUTE
key to unmute recording.
•
While recording is muted, the MUTE key
indicator lights up.
•
Pressing RECORD key (or REC key) during
a recording divides a recording into tracks
(track increment).
DVD RW HD
Auto track increment
four seconds or longer. However, recording may
sometimes stop if you press the RECORD key fre-
quently, even at an interval of five seconds. If you
plan to divide a recording into tracks repeatedly,
wait about ꢁ0 seconds until you press the RECORD
key again.
When recording, this allows the automatic division of
the recorded material into separate tracks when the fol-
lowing conditions occur:
1
Press and hold the ATRK switch on the rec page of
the virtual front panel for at least one second.
The auto track screen appears.
CAUTION
On a CD, two seconds of silence automatically fol-
low such a track division (no audio data is lost—the
input signal is buffered before being written to the
disc).
TIP
Note that tracks produced in this way must con-
form to the Red Book standard (be more than four
seconds long) and there can be a maximum of ꢇꢇ
tracks on a disc.
Figure 5.4: AUTO TRACK screen
2
3
Move the cursor to highlight MODE
.
Setting a level interval
Rotate the JOG/DATA dial to select LEVELor
You can specify the duration of silence to be detected in
level mode.
TIME
.
Move the cursor to the LEVEL INTERVAL parameter on the
auto track screen, then rotate the JOG/DATA dial to set
the duration in the range from one second through six
seconds (in one second steps).
4
Press the ENTER key to confirm the setting.
Automatic track increment in level mode
Depending on the input source, tracks are added as fol-
lows:
Press the ENTER key to confirm the setting.
Coaxial input When you record S/PDIF signal from
a CD, MD, or DAT while DD mode is turned on, the
PQ code is used to determine the track divisions. If a
digital audio signal that does not contain the PQ code is
input via the coaxial input, a new track is started when
the signal level rises above the threshold after having
fallen below the threshold for the duration specified by
the LEVEL INTERVAL parameter on the auto track screen.
Setting a delay
You can offset the automatic track increment position in
level mode.
Move the cursor to highlight DELAY in the auto track
screen, rotate the JOG/DATA dial to set the delay time
in the range of –1.70 seconds through +1.70 seconds in
0.01 steps, then press the ENTER key to confirm the set-
ting.
AES/EBU and analog inputs The threshold level
page 35) is used to divide tracks. A new track is started
when the signal level rises above the threshold after
having fallen below the threshold for the duration speci-
fied by the LEVEL INTERVAL parameter.
TIP
The automatic track increment recording in level
mode starts when the audio signal rises above the
specified sound threshold. Therefore, the beginning
of the audio may not be recorded, or the beginning
of the subsequent track may be concatenated to
the end of the current track. To avoid these prob-
lems, set DELAY to a negative value, change the
recording start time and the start position of the
source audio signal. Alternatively, you can lower the
sound threshold.
NOTE
You can also divide a recording into tracks manu-
ally by pressing the RECORD key during a record-
ing. Note that the DV-RA1000HD is unable to create
a track with a length of four seconds or less. Make
sure that you press the RECORD key at intervals of
ꢁꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
NOTE
track screen, then rotate the JOG/DATA dial to set the
interval in the range from 1 through 10 minutes (in
steps of one minute). (The default setting is 5 minutes.)
Press the ENTER key to confirm the setting.
If time mode is selected, the DELAY parameter is dis-
abled.
Automatic track increment recording in time
mode
NOTE
A maximum of ꢇꢇ tracks are allowed on a CD, and
a maximum of ꢇꢇ tracks in a project on a DVD RW
or HD. When the number of tracks reaches ꢇꢇ
during recording on a DVD RW or on the HD, the
DV-RA1000HD will continue recording on the ꢇꢇth
track.
In time mode, a recording is automatically divided into
tracks at every specified interval.
Specifying the interval
Move the cursor to highlight TIME INTERVAL on the auto
DVD RW HD
Synchronized recording
The synchronized recording function enables recording
to start automatically when the start point of the record-
ing source is detected, and to stop automatically when
the end point of the recording source is detected.
threshold after the Start ID of the PQ code is detected.
• If DD mode is on and digital recording takes place
through the COAXIAL connectors, recording starts
when the Start ID of the PQ code is detected from a
CD, DAT or MD player.
In the sound level screen, you can set a detection
threshold to trigger the start and end points of the
source. (See “Setting the sound threshold level (SOUND
LEVEL)” below.)
• If the source is analog, or digital other than the
above-mentioned recording starts if one second or
more of “below-threshold” signal is received, fol-
lowed by a signal above the threshold.
If the sound immediately starts at a loud level,
recording will not start.
You can also rehearse synchronized recording. Pressing
the SYNC switch on the rec page of the virtual front panel
repeatedly will cycle the function through off, rehears-
al, and on.
• Recording stops when the signal drops and remains
below the threshold longer than the duration speci-
fied by the SYNC STOP parameter, or in the case of
recording from a S/PDIF source, when a digital track
stop signal is received.
Recording starts and stops under the following condi-
tions:
• If a CD, DAT or MD is the S/PDIF recording source,
recording starts when the signal level rises above the
Settings in the sound level screen
The sound level screen enables you to set the sound
threshold level for synchronized recording and other
parameters.
Setting the sound threshold level (SOUND LEVEL
)
Synchronized recording starts when the
DV-RA1000HD detects audio signal level that goes
above a specified sound threshold level.
To display the sound level screen, move the cursor
to the SYNC switch on the rec page of the virtual front
panel, then press and hold the F5 key or ENTER key for
at least one second.
Select the threshold level from the following options:
–72dB, –66dB, –60dB, –54dB, –48dB, –42dB, –36dB,
–30dB, –24dB
NOTE
• The threshold level is also used for the auto cue
matic track increment in level mode (see “Auto-
• In DSD mode, if you have selected an option that
is lower than –ꢂꢆ dB, the DV-RA1000HD will use
the –ꢂꢆ dB setting.
Figure 5.5: Sound level screen
Move the cursor to a desired item, then rotate the
JOG/DATA dial to set the value.
After you finish making all necessary settings, press
the ENTER key to confirm the settings.
TASCAM DV-RA1000HD
ꢁꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
Follow the steps below to rehearse synchronized
recording and set the best recording start time:
Setting DD mode (DD MODE)
This parameter switches DD mode on and off.
1
Press the SYNC switch on the rec page of the vir-
tual front panel.
When you try to record S/PDIF signal from a CD, MD,
or DAT while DD mode is turned on, recording starts
when the unit detects the start ID in the PQ code. When
you use the synchronized recording function in DD
mode, recording starts when the source device starts
playing, and recording stops when the source device
stops playing.
The unit enters rehearsal mode and the RHSL
indicator lights up steadily.
2
3
Press the RECORD key, and then the PLAY key.
The RECORD key indicator lights up and the
PLAY key flashes.
If the automatic track increment function is in level
mode and DD mode is turned on, recording is automati-
cally divided into tracks when the track number on the
source device changes. (See “Auto track increment” on
Start the recording source.
The RECORD key flashes.
The DV-RA1000HD records to a buffer memory
and loops the first four seconds of the synchro-
nized source after the threshold is exceeded, and
displays the rehearsal screen.
Setting the sync delay parameter (SYNC DELAY)
Synchronized recording can be started earlier or later
than the point at which the DV-RA1000HD detects
an audio signal level that is higher than the specified
threshold.
The setting range is between −1.70 and +1.70 seconds
(in steps of 0.01 second).
Setting the sync stop parameter (SYNC STOP)
You can specify the time duration after which the
DV-RA1000HD will stop recording when the audio sig-
nal level drops below the specified threshold.
Figure 5.6: Rehearsing synchronized recording
Adjust the delay time, if necessary.
4
5
Press the ENTER key to confirm the setting.
The setting range is between 5 and 60 seconds (in steps
of 5 seconds) and INF (infinity, that is, recording will
continue even after the audio level drops below the
threshold).
The unit displays the home screen and enter
record ready mode.
NOTE
To cancel the setting, press the CANCEL key, in-
Rehearsed synchronized recording
stead of the ENTER key.
While the SYNC REC indicator is indicating “RHSL,”
synchronized recording can be rehearsed.
Making the recording
This allows “false starts” to be eliminated, as the
recording start time can be offset by up to 1.7 seconds
(in 0.01 second increments) from the time when input
signal level rises above the threshold (recording trig-
ger).
1
Press the SYNC switch on the rec page of the vir-
tual front panel to place the DV-RA1000HD in
synchronized recording mode.
The ON indicator lights up steadily.
2
3
Locate a source playback point slightly earlier
than the point from which you wish to record.
Press the RECORD key, then the PLAY key.
The RECORD key indicator lights up and the
PLAY key flashes.
4
Start playback of the source.
When the signal level rises above the specified
threshold, recording starts with a delay as speci-
fied by the DELAY TIME parameter.
ꢁꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
DVD HD
Monitoring
While not recording, it is possible to switch between
monitoring the input signal (the MONITOR indicator is
on) and the playback of the disc.
Note that this function is automatically turned on (i.e.,
monitoring the input) when the DV-RA1000HD is
recording or in record ready mode.
Use the MONITOR key on the main unit or the
RC-RA1000 to switch this function on (as shown by the
indicator lighting).
page 24) can be used to turn monaural monitoring on
and off (but this does not work in DSD mode).
DVD HD
Oscillator
While not recording, the oscillator is available from
the virtual front panel. (See “The virtual front panel
Use the F1 and F2 keys to navigate, and the JOG/DATA
dial to change the SWITCH parameter between ONand
OFF.
The oscillator output level is a reference level of analog
output.
Change the frequency (FREQ) between 440Hz, 1kHz
and 10kHz
.
Pressing the on-screen OSC switch (use F5
(PUSH)) briefly
NOTE
turns the oscillator on or off (nominal level).
This feature can also be used with DVD and HD but
not in DSD mode.
Pressing and holding the switch brings up the oscillator
setting screen:
Figure 5.7: Oscillator screen
Dithering
Only available when recording CDs, use of the noise
shaped dithering option may help signal-to-noise ratio
when recording from digital 24-bit sources to a 16-bit
CD.
There are no options—simply turn the function on or
off using the virtual front panel. (See “The virtual front
Copy protection
This digital copy protection (SCMS) is only available
when recording CDs (not DVDs and HD).
•1GENERATION–(single generation) “Children”
may be digitally copied from the disc, but no “grand-
children” may be produced from these children.
The SYSTEM SETUP menu COPY ID allows three choices:
None of these settings applies to analog copies made
from the disc, of course.
•FREE–(free) no copy prohibit is enabled. Digital
copying from the disc is possible.
Press ENTER to confirm this setting.
•PROHIBIT–(prohibited) copy prohibit is enabled.
No digital copying is possible.
The setting may be changed on a track-by-track basis.
TASCAM DV-RA1000HD
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
Finalizing discs
When recording has taken place on a CD-R or CD-RW
disc, the TOC must be written to allow the disc to be
played on ordinary CD players.
The screen shows an appropriate message while final-
ization is taking place (about a minute). No cancellation
is possible until the finalization is complete.
Press the on-screen FINALIZE switch in the Virtual Front
to bring up a pop-up message.
NOTE
This function may also be accessed through the
dedicated FINALIZE key on the RC-RA1000.
Press ENTER to finalize the disc, or CANCEL to return
to the VFP.
Unfinalizing discs
This is the opposite of finalizing—removing the TOC
to allow more tracks to be added (subject to the space
available on the disc).
Press ENTER to unfinalize the disc, or CANCEL to
return to the VFP.
The screen shows an appropriate message while the
disc is being unfinalized (about a minute).
This is only possible with CD-RW discs, of course.
To unfinalize a disc, press the on-screen UNFINAL switch
in the Virtual Front Panel (see “The virtual front panel
(VFP)” on page 23) to bring up a pop-up message.
NOTE
This function may also be accessed through the
dedicated UNFINALIZE key on the RC-RA1000.
Erasing discs (CD-RW)
CD-RW discs can be erased and reused using the erase
function available from the VFP.
Press ENTER to erase the disc, or CANCEL to return to
the VFP.
To erase a disc, press the on-screen ERASE switch in
the Virtual Front Panel (see “The virtual front panel
(VFP)” on page 23) to select either a full erase of the
disc (Full Erase) or a faster erase (Fast
Erase) process and bring up a pop-up message.
NOTE
The Fast Erase process removes only the TOC, but
not the entire data.
ꢁꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
5 − CD playback & recording
DVD RW HD
About marks
A maximum of 99 marks can be added to a disc (CD) or
to a project (DVD±RW/HD) to help with location, etc.
These marks can be edited.
•
•
Pressing and holding the DISPLAY key and
then pressing the MARK key brings up the
locate list screen.
NOTE
Use the JOG/DATA dial to scroll through the
list. Marks are displayed in the order they
appear in the play list (DVD/HD). If the
play list order changes, so does the mark list
order.
• Although marks can be added to a CD recording
project (or to a pre-recorded CD), they are not
stored when the CD is ejected.
• Marks can be stored on a DVD or in the HD as
information. Note, however, that the marks will
not be saved if you do not write the UDFMI to the
• You do not need to write the UDFMI manually in
an HDD project.
•
Press the MARK key to add a mark at the
point where the key was pressed. “Set
mark!” appears for a second to let you
know the mark has been set.
Figure 5.8: The locate list
NOTE
•
Marks can be added when stopped, paused,
playing back or recording.
The MARK key on the RC-RA1000 remote control
unit can be used to enter marks, and the LOCATE
key can be used to bring up the locate list.
Jumping to a mark
NOTE
•
To jump to a location mark, use the
This function is available for DVD R discs.
JOG/DATA dial to highlight it in the list, and
press ENTER
.
Editing marks
•
From the locate list, use F3 and F4 to start
editing the currently-highlighted mark.
•
•
Press ENTER when the editing is complete.
The mark is then highlighted, and you can
use it for location.
Use F1 (DEL) to delete the highlighted mark
from the list.
CAUTION
• If you do not write the UDFMI information to disc,
the marks will not be saved. (See “Writing the
Figure 5.9: Editing a mark
• If you change the mark position, the locate list
will be automatically updated and sorted by time.
• If you set a mark to a position beyond the end of
the track, the mark will automatically be placed
at the end of the track when you press the ENTER
key.
•
Use the cursor keys to highlight the time
fields and the JOG/DATA dial to edit these
fields, to slip the position of the mark.
TASCAM DV-RA1000HD
ꢁꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
The DV-RA1000HD features high-resolution recording
using DVD±RW discs or HD. The format of this high-
resolution recording is different from that for recording
a standard DVD audio, SACD, or CD-DA disc.
tion (DAW) for later sound processing and pre-master-
ing.
NOTE
On the DV-RA1000HD, you can use DVD RW discs
and the HDD for real-time recording. You can use
DVD R discs only in copy mode to duplicate data.
The recording process creates an archive of audio files
which you can edit using a DV-RA1000HD. Also, these
files can be subsequently transferred to external devices
or personal computer such as a digital audio worksta-
Organization of projects and files
On the DV-RA1000HD, a project consists of up to 99
audio files—the same number as the maximum number
of tracks on a Red Book CD-DA.
You can have different projects on the same disc (up to
99 of them, in fact), and different projects can have dif-
ferent sampling frequencies.
When you format a brand new DVD±RW disc with the
DV-RA1000HD, a new project is automatically added
to the disc. (See “Using a new DVD±RW disc” on page
41.) The DV-RA1000HD internal HD already includes
one default project (44.1kHz, 24-bit) at the time of ship-
ment.
As well as the audio files, a project also contains the
following information:
• Mark data
• Text associated with the project other than the file
names
• A play list showing the running order
In a project, all the files must be the same sampling fre-
quency (or all in DSD format). This is determined when
the project is set up.
Writing the UDFMI
In order for the DV-RA1000HD to read the information
on a DVD±RW disc, control information referred as
UDFMI (UDF Management Information) must be writ-
ten to the disc.
TIP
This SAVE UDFMI function is also installed by de-
CAUTION
Although the DV-RA1000HD writes this control infor-
mation at key events, such as when the disc is ejected,
when the unit is shut down (see “Shut down” on page
19), or when ODD/HDD mode is switched, unexpected
power loss may cause a disc to appear unreadable.
There is a limit to the number of times that DVD RW
media used by the DV-RA1000HD can be written.
This also applies to the UDFMI. It is impossible to
provide definite guidelines on the number of times
this is possible, but the type of media, environmen-
tal factors, etc. introduce an element of unpredict-
ability. We therefore recommend that wherever
possible, you use new media for important record-
ing projects, to prevent the possibility of data loss
caused by media errors.
To write the UDFMI manually:
1
While the transport section is stopped, select the
DISC sub-menu from the main menu.
2
3
Highlight the SAVE UDFMI item and press ENTER.
A popup asks you if you are sure. Press ENTER to
continue, and a progress bar shows the progress
of the operation.
Press CANCEL to cancel the operation.
Viewing the number of rewriting times
The number of times the current disc has been rewrit-
ten can be viewed in the check screen. Select CHECK in
the system setup menu to display the check screen.
Then, press the F3
(MEDIUM) key to view the number.
ꢂ0
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
Recording times and track lengths
DVD RW discs recording
Maximum
track length
(minutes)
Sampling Recording Disc time
The total time recordable on a DVD±RW single-layer
disc depends on the sampling frequency.
frequency
type
(minutes)
44.1 kHz
48 kHz
88.2 kHz
96 kHz
176.4 kHz
192 kHz
2.8224 MHz
PCM
PCM
PCM
PCM
PCM
PCM
DSD
290
266
144
133
70
135
124
67
In addition, the maximum file size is fixed at 2GB.
This means that the maximum recording time per track
also varies according to the sampling frequency.
All audio files must be at least four seconds in length.
62
33
66
30
107
50
Table 6.1: Sampling frequencies and
recording times
All audio files on the HD must be at least four seconds
in length.
HD recording
The total time recordable on the HD is significantly
longer than the time recordable on a DVD±RW disc.
However, the maximum file length on the HD is the
same as for a DVD±RW disc. There is a limit to the
recording time for each project.
The following recording times are estimates. You can-
not extend the recording time beyond the maximum
time specified for each project.
Sampling
frequency
Recording
type
Maximum recordable time on the HD
Maximum project length
(60 GB)
44.1 kHz
48.0 kHz
PCM
PCM
PCM
PCM
PCM
PCM
DSD
811 minutes (13.5 hours)
745 minutes (12.4 hours)
405 minutes (6.7 hours)
372 minutes (6.2 hours)
202 minutes (3.3 hours)
186 minutes (3.1 hours)
811 minutes (13.5 hours)
3779 minutes (62.9 hours)
3472 minutes (57.8 hours)
1889 minutes (31.4 hours)
1736 minutes (28.9 hours)
944 minutes (15.7 hours)
868 minutes (14.4 hours)
1417 minutes (23.6 hours)
88.2 kHz
96.0 kHz
176.4 kHz
192.0 kHz
2.8224 MHz
Table 6.2: Sampling frequencies and recording times
Using a new DVD RW disc
When you insert a new DVD±RW disc into the tray and
close it, the DV-RA1000HD displays a popup screen.
Press the ENTER key to display the format screen
shown below. Follow the steps below to format the disc:
1
2
Press the F1 or F2 key (cursor) to highlight
FORMAT
.
Rotate the JOG/DATA dial to select QUICKor
FULL
.
NOTE
Quick format
You cannot use a DVD R disc which is not re-
corded any project. If you insert a DVD R disc into
the tray, the DV-RA1000HD displays a message
“UNUSABLE DISC.”
This formatting writes a project file and other neces-
sary data, then places the DV-RA1000HD in record
ready mode in a few minutes.
If you insert a brand new disc, the DV-RA1000HD will
work in the background when the unit is not recording
or playing to format an unrecorded area on the disc.
Figure 6.3: Format screen
TASCAM DV-RA1000HD
ꢂ1
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
NOTE
•
While the DV-RA1000HD is formatting a
DVD-RW disc in the background, the disc
remains in “open” status. (The “OPEN”
indicator flashes in the disc status section
of the home screen.) A personal computer is
unable to read these “open” discs. To use the
discs with your computer, you must perform
the close operations. (See “Close and open
(DVD RW)
• During a background format operation, the
CLOSEindicator (for DVD+RW) or OPEN
indicator (for DVD-RW) flashes in the upper right
corner of the home screen. When the format op-
eration is complete, the flashing CLOSE/OPEN
indicator will be turned off.
• Start recording after the background format
operation is complete. If you attempt to record
during a background format operation, the
DV-RA1000HD may try to record data in an unfor-
matted area on the disc.
•
While the DV-RA1000HD is formatting a
DVD+RW disc in the background, the disc
remains in “closed” status. (The “CLOSE”
indicator flashes in the disc status section of
the home screen.) You can use this disc with
your computer.
• Do not insert a partially formatted disc into a
computer’s disc drive. Otherwise, the back-
ground format operation may resume incorrectly
on a different drive.
• Do not insert a disc formatted with a computer
into the DV-RA1000HD disc tray. Format a disc
using the DV-RA1000HD if you plan to use the
disc with the DV-RA1000HD.
Full format
This formatting method formats the entire disc and
takes about 30 minutes or more to complete.
Using a non-supported disc
3
4
Use the F1 or F2 key (cursor) to highlight NAME.
When you insert a disc not supported by the
Use the F3 or F4 key (cursor) and the JOG/DATA
dial to enter a project name, then press the
ENTER key.
DV-RA1000HD into the tray and select ODD mode,
the DV-RA1000HD displays a popup message that the
disc type is not supported. Press ENTER to display a
message that requests confirmation. Press ENTER again
to format the disc (this is not recommended). Using a
disc formatted in this way may cause writing or read-
ing errors more frequently. Do not use such a disc for
recording important materials.
5
6
Use the F1 or F2 key (cursor) to highlight MODE.
Rotate the JOG/DATA dial to select the audio for-
mat mode from the following options:
192kHz - 24bit,
176.4kHz - 24bit,
96kHz - 24bit,
88.2kHz - 24bit,
48kHz - 24bit,
44.1kHz - 24bit,
DSD
You can view the information of the loaded disc by
Using an already recorded disc
When you insert a disc on which multiple project have
already been recorded and select ODD mode, the proj-
7
Press the ENTER key to start formatting.
The DV-RA1000HD starts formatting the disc
and create a project. When the format opera-
tion is complete, the DV-RA1000HD displays the
home screen.
If a disc contains only one project, that project automat-
ically opens.
•
If you press the CANCEL key during a full
format operation, a popup screen requests
confirmation. Press the CANCEL key to con-
tinue formatting. Or, press the ENTER key to
cancel the full format operation. When the
full format operation is cancelled, formatting
will be performed in the background.
NOTE
Once you select a project, the project remains
selected until you eject the disc. (Even if you switch
to HDD mode, then switch back to ODD mode, the
same project will open.)
You can eject a disc or shut down the unit
during a background format operation.
•
If you perform the full format operation
with a DVD-RW disc, the DV-RA1000HD
will automatically carries out the close oper-
ation.
ꢂꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
Close and open operations for DVD-RW discs
Close operation
•
When a DVD-RW disc is “closed,” the disc
status indicator on the home screen changes
You must perform the “close” operation when using a
DVD-RW disc on the DV-RA1000HD to enable your
computer to read data from the disc.
from OPENto CLOSE
.
Open operation
If you perform the full format operation with a
DVD-RW disc, the DV-RA1000HD will automatically
carry out the close operation.
If you “open” a DVD-RW disc that was “closed” after
the quick format operation, you will be able to write
data in the unformatted area. However, such an “open”
disc cannot be read or written on a computer.
If you perform the quick format operation, follow the
steps below to perform the close operation. However,
when the background format on a quick-formatted disc
is complete, the DV-RA1000HD will automatically car-
ries out the close operation.
1
2
3
From the main menu, select the DISC menu, then
press the ENTER key.
The DV-RA1000HD displays a disc sub-menu.
Select OPEN, then press the ENTER key.
After a quick-formatted disc is “closed,” you can use
only the formatted area on the disc.
A popup message asks whether you wish to ex-
ecute the open operation.
1
2
3
From the main menu, select the DISC sub-menu,
then press the ENTER key.
Press the ENTER key.
The DV-RA1000HD opens a disc menu.
The open operation starts. When it is complete,
the unit displays the home screen.
Select CLOSE, then press the ENTER key.
•
When a DVD-RW disc is “opened,” the disc
status indicator on the home screen changes
A popup message asks whether you wish to ex-
ecute the close operation.
from CLOSEto OPEN
.
Press the ENTER key.
•
Full-formatted DVD-RW discs cannot be
opened.
The close operation starts. When it is complete,
the unit displays the home screen.
Adding a new project
As a disc can contain more than one project, you can
also use the menu system to create a project on a disc
that has already been formatted, and contains a project.
1
2
Select the PROJECT sub-menu from the main menu.
Highlight CREATE and press ENTER
.
This brings up the screen allowing you to enter
the name and properties of a project, as de-
scribed in the previous section.
Figure 6.4: Creating a new project
Adding notes to a project
Add notes on artists, recording details, etc. to a project.
Unlike a written disc insert or tape label, these notes
will always stay with the disc. You can enter up to 1000
characters for session notes, etc.
NOTE
The DV-RA1000HD displays notes regarding a
DVD R disc. You cannot edit these notes.
Figure 6.5: Adding notes to a project
1
2
Select the PROJECT sub-menu from the main menu.
Highlight the PROJECT TEXT sub-menu and press EN-
TER
.
TASCAM DV-RA1000HD
ꢂꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
carriage return). Press and hold CANCEL to exit
without saving (brief presses of CANCEL act as a
delete key).
3
4
Use the soft keys and JOG/DATA dial (or an at-
tached PS/2 keyboard) to enter the text. (See
You can add more lines to the notes than you
can see on screen and scroll up and down to view
them.
NOTE
Remember that this text will not be stored on
Press and hold ENTER for a second or so, to store
the project text (brief presses of ENTER add a
Changing the current project
1
Select the PROJECT sub-menu from the main menu.
2
Highlight the OPEN sub-menu to show a list of the
names of all projects on the disc, together with
their sampling frequencies.
The current project is shown with an arrow be-
side the name.
Figure 6.6: Loading a project
3
3
Use the JOG/DATA dial to move the cursor to the
project to be loaded, and press ENTER. The se-
lected project is then loaded (the sampling fre-
quency is automatically changed).
Changing the name of a project
1
Select the PROJECT sub-menu from the main menu.
Use the JOG/DATA dial to move the cursor to the
project to be renamed, and press either the F3 or
F4 key.
2
Highlight the OPEN sub-menu to show a list of the
names of all projects on the disc, together with
their sampling frequencies (see Figure 6.6, Load-
ing a project).
You can then edit the name of the project as
explained in “Naming files, projects, marks, etc.”
The current project is shown with an arrow be-
side the name.
4
3
Press ENTER when done.
Deleting a project from disc
1
Select the PROJECT sub-menu from the main menu.
Press the F1 (ERASE) key to delete the highlighted
project. You are asked to confirm the deletion.
Press ENTER to delete, or CANCEL to cancel the
operation.
2
Highlight the OPEN sub-menu to show a list of the
names of all projects on the disc, together with
their sampling frequencies.
All files in the project will be deleted along with the
project itself.
The current project is shown with an arrow be-
side the name (see Figure 6.6, Loading a project).
Formatting a disc
When a disc that has already been used is formatted, a
new project is automatically added to the disc.
Reformatting a DVD±RW disc on the DV-RA1000HD
will never result in an entirely blank disc (but of course,
all previous data is removed during a format process).
CAUTION
If you attempt recording many times to the same
DVD RW disc and erasing or formatting it often,
you may find that it does not record properly. You
should use a new disc for any really important re-
cordings.
ꢂꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
1
2
3
Select the DISC sub-menu from the main menu.
4
Press ENTER to start the formatting process.
This will take a few minutes, and the unit is not
usable while the format takes place.
Highlight the FORMAT sub-menu and press ENTER.
Enter a name and sampling frequency for the
first project to be created on the newly-formatted
41).
NOTE
You cannot use DVD RW discs which have been
formatted on a computer for recording with the
DV-RA1000HD.
Recording files to disc
Once a project has been set up, audio files can be
recorded at the sampling frequency and word length
specified by the project.
TIP
In the same way as when the DV-RA1000HD is
recording CDs, pressing RECORD while recording
will create a track division. Also, to create several
tracks from one recording (for example, when mak-
ing a live recording), you can use the file divide
function. (See “Dividing files” on page ꢂꢆ.)
Note that tracks divided in this way cannot be less
than four seconds in length. Also note that repeated
track divisions creating many short tracks (of five
seconds or so) may cause the unit to stop record-
ing. We recommend that you use manual track divi-
sion to create tracks of about ꢁ0 seconds in dura-
tion.
1
Press the RECORD key. While the disc and drive
are being “lined up” for recording, the READY
indicator flashes.
2
When the READY indicator is lit, press PLAY to
start recording.
While recording, the display shows either the
elapsed time of the track, or the remaining time
on the disc (change this with the DISPLAY key).
Note that if the recording mode is set to Over-
write, the elapsed time of the overwritten track is
shown.
To mute recording (that is, recording silent part),
press and hold the MUTE key. Release the MUTE key
to unmute recording.
While recording is muted, the MUTE key indicator
lights up.
4
Press STOP to finish recording.
Recording mode
In normal recording mode, stopping and restarting a
recording will create a new track.
To select a recording mode, use the RMODE switch on the
rec page of the virtual front panel, or the RECMODE
key on the RC-RA1000 remote control unit.
On the other hand, in overwrite mode, restarting a
recording will overwrite data from the current position
in the same track. For example, if you stop then resume
recording, a new track will not be added to the disc.
Instead, recording will continue from the point at which
you previously stopped on the same track. If the play-
back position is located in the middle of the current file
and you start recording in overwrite mode, new data
will be written over the existing data from the point at
which you started recording, in much the same way as
an analog tape recorder.
Normal mode
“
N” appears above the RMODE switch on the rec page of
the virtual front panel.
Overwriting mode
“
O” appears above the RMODE switch on the rec page of
the virtual front panel.
NOTE
To view the current recording mode, open the rec
page of the virtual front panel. The mode setting is
not displayed on the home screen.
NOTE
Overwriting mode is available only for recording in
PCM mode on a DVD RW disc or in the HD.
TASCAM DV-RA1000HD
ꢂꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
Playing back files
Use the DV-RA1000HD in much the same way as a
CD player when playing back the files recorded on a
DVD±RW disc or HD.
NOTE
During DVD or HD playback, neither Start ID nor
Track ID is transmitted from the AES/EBU or S/PDIF
outputs. (Both IDs are transmitted from the S/PDIF
output during CD playback.)
Repeat functions, etc. will work as with CDs.
Play lists
A play list is a list in which files are assigned to tracks
on a DVD disc. Unlike a programmed playback list (see
“Programmed playback” on page 30), each file in a play
list must appear once (and only once).
TIP
Only one play list per project can be created, but it
is possible to program a play list so that the tracks
are played in a different order, leaving unwanted
tracks to the end.
Figure 6.7: Editing a play list
3
4
Use the JOG/DATA dial to highlight a file.
Play lists are created from the files present in a project
in the following way:
Use the F1 (up) and F2 (down) keys to move the
highlighted file up and down in the play list or-
der.
1
2
Select the EDIT sub-menu from the main menu.
From this sub-menu, select PLAY LIST
.
5
Press ENTER when done.
Restructuring the play list
If you copied audio files (in BWF or DSDIFF for-
mat) from a computer to projects on the HD of
DV-RA1000HD or to a DVD disc, you must restructure
the play list to play back these audio files using the
DV-RA1000HD. Follow the steps below:
•
Multiple audio files added to the play list will
be sorted in alphabetical order. (If the audio
files you attempt to add cause the play list to
grow longer than the duration of the speci-
fied project, only the files that will not cause
the play list to exceed the specified duration
will be added in alphabetical order to the
play list).
1
Open a project to which you copied audio files
from a computer.
2
Press the F3 key in the play list screen.
NOTE
A popup message appears, asking whether you
wish to restructure the play list.
When the play list is being restructured, the trans-
ferred BWF file might be converted to a different
format to suit the unit. In this case, the converted
file may lose some information specific to the appli-
cation that created the BWF-format file.
3
Press the ENTER key.
The DV-RA1000HD starts restructuring the play
list.
Any audio files (in BWF or DSDIFF format) in
the project folder that are not included in the
current play list will be added to the end of the
play list.
Setting marks
As when recording CDs, you can use this facility to set
location marks which can then be used for location pur-
However, when recording to DVD±RW/HD, these
marks are written to UDFMI as part of the project.
ꢂꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
Erasing a file
You can erase the current file in the following way:
Select the EDIT sub-menu from the main menu.
2
3
From this sub-menu, select ERASE. A popup mes-
sage appears.
1
Press ENTER to erase the file, CANCEL to cancel
the action.
Renaming a file
When the DV-RA1000HD records files, it numbers
them in sequence, starting at 0, which is probably not
very useful in the future.
3
Use the JOG/DATA dial to highlight a file, and
press the F3 or F4 key to start editing.
To rename files, and provide them with meaningful
titles for future reference:
1
2
Select the EDIT sub-menu from the main menu.
From this sub-menu, select RENAME. Press ENTER
.
Figure 6.9: Editing file names (ii)
4
5
Edit the file name as described in “Naming files,
Press ENTER when done.
Figure 6.8: Editing file names
Editing files
CAUTION
These editing operations are destructive, but there
is one level of undo available which applies to the
operations in the edit menu.
Combining files
If two recordings have been made in the same project
which are to form one track, the files can be joined
together.
2
From this sub-menu, select COMBINE. Press ENTER.
NOTE
This operation is not possible with files recorded in
DSD mode.
You cannot join together files that are transferred
from a CD if the CD has its copy ID set to “prohibit.”
Figure 6.10: Confirming a file combine operation
The current file is joined to the file following it in the
play list (so if two files are to be joined and they are not
next to each other in the play list, the play list must be
edited). (See “Play lists” on page 46.)
3
Press ENTER to combine the files, or CANCEL to
cancel the operation.
NOTE
TIP
The maximum size of a file is ꢀ GB, as explained on
combining two files will create a file larger than this,
a popup message alerts you to the fact, and you
cannot proceed with the combine operation.
Although this technique simply appends one file to
the end of another, it is possible to remove unwant-
ed heads and tails using the editing functions. (See
1
Select the EDIT sub-menu from the main menu.
TASCAM DV-RA1000HD
ꢂꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
6 − DVD RW/HD playback & recording
Dividing files
You can split a file into two parts at the current play-
back position. This may be useful if you want to divide
a single long live recording into separate tracks, for
example.
NOTE
This operation is not possible with files recorded in
DSD mode.
You cannot divide a file that is transferred from a
Figure 6.11: Confirming a file divide operation
CD if the CD has its copy ID set to “prohibit.”
The DV-RA1000HD enters pause mode, and the
first three seconds of the file following the divi-
sion point are played back as a loop. Use the
JOG/DATA dial to trim the division point so that
the new file starts at the point you want.
TIP
You may want to set a mark at the split point so that
you can locate it easily.
File division always takes place on the current file.
Each resulting file must be at least 4 seconds in length
to be usable. If neither part resulting from the division
is greater than four seconds in length, the divide opera-
tion cannot be carried out. If one resulting file is under
4 seconds in length, a popup message warns you. If
you carry on with the divide operation, the short part is
deleted (of course, this might be a cough or fret noise
before a take which would be edited out in any case).
3
Press ENTER to set the division point and split the
file. The name of the second file is automatically
created by the DV-RA1000HD following division,
and is changed to BWF_FileXX where XX is the
next number following any number already used
by such a file in the current project.
TIP
If the second part of the divided file that you have
already renamed is the part you want to keep (e.g.
you are removing breath noise or drumstick clicks
at the start of a track), you must delete the file cre-
ated from the first part of the divided file, and re-
name the remaining BWF_FileXX file to the original
value.
1
2
Select the EDIT sub-menu from the main menu.
From this sub-menu, select DIVIDE. Press ENTER
.
Undo and redo
The last action performed in the edit menu can be
undone (split files can be recombined and joined files
can be resplit, play lists can be undone, etc.).
1
2
Select the EDIT sub-menu from the main menu.
Highlight UNDO/REDO and press ENTER. A popup
message appears with either Undoor Redo
followed by the name of the operation you are
undoing or redoing (combine, divide, play list,
etc.).
,
If an action has been undone, you can redo it.
Note that if any recording is done following an edit
operation, that edit operation can no longer be undone.
Likewise, if any recording is done following an undo
operation, that undo operation can no longer be redone.
3
Press ENTER to undo or redo the named opera-
tion, or CANCEL to cancel the undo/redo.
ꢂꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
The DV-RA1000HD features the following copy func-
tions that enable you to copy projects and files between
disks.
•CD to HDD (Copying tracks from a CD to the HD)
You can use the copy functions with DVD±RW discs as
well as DVD±R discs.
•DVD to HDD (Copying files and projects from a
DVD to the HD)
NOTE
information on copying files between the computer
and the HD of DV-RA1000HD or a DVD RW disc
formatted by the DV-RA1000HD.
•HDD to DVD (Copying files and projects from the
HD to a DVD)
•HDD to CD (Creating an audio CD using a project
on the HD)
Selecting a copy mode and copy source
The following procedure is common to all copy func-
tions.
press the ENTER key. (To change the disc, press
the CANCEL key. The DV-RA1000HD ejects the
disc and displays a message that requests that
you insert a disc.)
Select a copy mode, then select a copy source (project
or file). If a project in the copy destination uses the
same name as the selected source project, select to indi-
cate whether you wish to overwrite the existing project
or cancel the copy operation.
If an inserted disc is not compatible, the tray
opens, and a popup message requests that you
insert another disc.
1
Select the COPY sub-menu from the main menu,
then press the ENTER key.
4
The DV-RA1000HD displays the source project
selection screen. (This does not apply to a source
CD.)
The DV-RA1000HD displays the copy menu
screen.
Figure 7.2: Selecting a project
Figure 7.1: Copy menu screen
•
To change the disc, press the CANCEL key.
(The tray opens and a popup message
requests that you insert another disc.)
2
Select a desired copy mode, then press the ENTER
key.
5
Use the function keys to select a copy source
project.
If a compatible copy source or destination disc
has already been inserted into the tray, a popup
message requests confirmation. Press the ENTER
key.
To select a highlighted project, press the F1 (SELECT)
key. The selected project is marked with a check
mark to the left of its name. Press the F1 key
again to deselect the project.
If a compatible copy source or destination disc
is not inserted into the tray, or if you press the
CANCEL key at the confirmation popup message,
the disc tray automatically opens and a popup
message requests that you insert a copy source
disc into the tray.
To select all projects, press the F2 (ALL SEL.) key.
To deselect all selected projects, press the F3
(ALL REL.) key.
To display a file selection screen, press the F4 (FILE)
key while the project marked with a check mark
is selected.
3
Insert a copy source or destination disc (depend-
ing on the copy mode) into the tray, then press
the ENTER key.
If the project is not marked with a check mark,
pressing the F4 key will not open the file selection
screen.
The DV-RA1000HD checks to confirm that the
disc whether the disc is compatible.
If you insert an unsupported disc, an error mes-
sage appears. To continue the copy operation,
TASCAM DV-RA1000HD
ꢂꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
To display the project selection screen, press the
F4 (PROJECT) key or the CANCEL key.
•
After you press the F4 key to display the file
selection screen, you can select a file to be
copied using the function keys. When the file
selection screen is first displayed, all files are
selected. (That is, all files are marked with a
check mark to the left of each file name.)
•
If the total size of the selected files exceeds
the available space on the destination disc, a
popup message appears and all operations,
excluding deselection of the files, will be dis-
abled.
To select or deselect a highlighted file, press the
F1 key.
6
Press the ENTER key to confirm the file selection.
To select all files, press the F2 (ALL SEL.) key.
If a project in the copy destination uses the same
name as the selected source project, a screen will
request confirmation for the copy operation.
To deselect all selected files, press the F3 (ALL REL.)
key.
Same project name in the destination
If a project in the copy destination uses the
same name as the selected source project, the
DV-RA1000HD displays the following duplicate
project screen that lists projects with the same
name.
To overwrite a highlighted project with the
source project, press the F1 (REPLACE) key. The
project overwritten is marked with an “O” to the
left of its name.
To not overwrite a highlighted project with the
source project, press the F2 (NOT COPY) key. The
project is marked with an “N” to the left of its
name.
Continue to select overwriting or canceling for
each project in the list. When all duplicate issues
are resolved, press the ENTER key.
The DV-RA1000HD displays a screen that re-
quests confirmation of the copy operation.
Figure 7.3: Duplicate project screen
Determine whether you wish to overwrite each
project in the list with the source project, or can-
cel the copy operation.
7
Follow the instructions on the screen to perform
the copy operation.
Copying files and projects from a DVD to the HD
You can copy data from a DVD±RW or DVD±R disc to
the HD of DV-RA1000HD.
3
Select a project/file to copy.
You can select multiple projects.
1
2
Select DVD to HD in the copy menu screen.
You can also copy specified files inside a project,
instead of copying the entire project.
Insert a copy source DVD following the instruc-
tions on the screen.
For more information, see “Selecting a copy
The DV-RA1000HD displays a source project
selection screen.
4
After you select a project, press the ENTER key.
For more information, see “Selecting a copy
If a project in the HD uses the same name as
the selected source project, the DV-RA1000HD
displays a duplicate project screen that lists all
projects that use the same name. Follow the pro-
cedure in the “Same project name in the destina-
tion” section described above to resolve the name
duplicate issues, then press the ENTER key.
A message requests confirmation to start copying
data to the HD.
Figure 7.4: Selecting a source project
ꢃ0
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
During this procedure, the DV-RA1000HD dis-
plays a progress bar. When the procedure is
complete, the unit displays the home screen.
5
Press the ENTER key.
The selected source projects or files are copied to
the HD.
After the copy operation is complete, the
DV-RA1000HD initiates a procedure to quit copy
mode.
Copying files and projects from the HD to DVD
You can copy data from the HD of DV-RA1000HD to a
DVD±RW or DVD±R disc.
name. Follow the procedure in the “Same project
name in the destination” section described above
to resolve the name duplicate issues, then press
the ENTER key.
1
2
Select HD to DVD in the copy menu screen.
Insert a copy destination DVD following the in-
structions on the screen.
A message requests confirmation to start copying
data to the DVD.
The DV-RA1000HD displays a source project
selection screen.
5
6
Press the ENTER key.
The selected source projects or files are copied to
the DVD.
•
If you insert an unsupported disc, an
error message appears. To continue the
copy operation, press the ENTER key. To
change the disc, press the CANCEL key. The
DV-RA1000HD ejects the disc and displays a
message that requests that you insert a disc.
After the copy operation is complete, a message
appears, asking whether you wish to copy the
data to another disc.
To copy the data to another disc, press the ENTER
key.
For more information, see “Selecting a copy
The DV-RA1000HD automatically opens the tray.
Follow the steps 4 and 5 described above.
If you do not wish to copy the data to another
disc, press the CANCEL key.
The DV-RA1000HD initiates a procedure to quit
copy mode.
During this procedure, the DV-RA1000HD dis-
plays a progress bar. When the procedure is
complete, the unit displays the home screen.
Figure 7.5: Selecting a source project
3
4
Select a project/file to copy.
•
Copying the data to a DVD±RW disc that
already contains data
You can select multiple projects.
You can also copy specified files inside a project,
instead of copying the entire project.
If available space on the disc is smaller than
the total size of the projects selected for the
first copy operation, the DV-RA1000HD will
check the disc, open the tray, then display a
popup menu that requests that you insert a
disc.
After you select a project, press the ENTER key.
If a project in the destination DVD uses the
same name as the selected source project, the
DV-RA1000HD displays a duplicate project
screen that lists all projects that use the same
TASCAM DV-RA1000HD
ꢃ1
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
Creating an audio CD using a project on the HD
You can create an audio CD using project files on the
HD of DV-RA1000HD as source material. Each file
creates a track on the CD. You can also insert two sec-
ond of silence between tracks. Note that the project files
must be in 44.1 kHz/24-bit audio format.
1
2
Select HD to CD in the copy menu screen.
Insert a copy destination CD following the in-
structions on the screen.
Figure 7.7: Track order screen with time indication
5
Specify the track order on the destination CD.
The DV-RA1000HD displays a source project
selection screen.
To do this, use the JOG/DATA dial to select a track
(file), then use the F1 and F2 (up/down) keys to
place the track in the desired track order loca-
tion.
•
If you have inserted a CD-RW disc that
already contains data, the DV-RA1000HD
displays a popup message, asking whether
you wish to delete the data on the disc.
6
After you specify the track order, press the
ENTER key.
Press the ENTER key to delete the data on the
disc. To change the disc, press the CANCEL key.
The unit opens the tray and displays a popup
message that prompts you to insert a disc.
The track order is confirmed, and the unit dis-
plays a screen that enables you to specify a silent
interval (gap) between tracks.
After you delete the data on the CD-RW disc, or
if you have inserted a blank CD-R/RW disc, the
DV-RA1000HD displays a source project selec-
tion screen.
If you have inserted any other disc, the unit
opens the tray and displays a popup message that
requests that you insert a disc.
Figure 7.8: Track order screen with a gap column
For more information, see “Selecting a copy
7
8
Add a silent gap between tracks.
To do this, use the F1 and F2 (up/down) keys to
highlight a position in which you wish to add a
gap, then use the JOG/DATA dial to turn the gap
on or off. When the gap is turned on, it is set to
two seconds.
After you set the gap between tracks, press the
ENTER key.
Figure 7.6: Selecting a source project
The DV-RA1000HD displays the CD text edit
screen.
3
4
Select files to copy.
First select a project that contains the file or files
you wish to copy, then select the files.
After you select files, press the ENTER key.
The DV-RA1000HD displays the track order
screen.
Figure 7.9: CD text edit screen
By default, each track uses the name of the cor-
responding file, and the disc title field is blank.
ꢃꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
If you have inserted a CD-RW disc that already
contains data, the DV-RA1000HD displays a pop-
up message, asking whether you wish to delete
the data on the disc.
Press the ENTER key to delete the data on the
disc. To change the disc, press the CANCEL key.
The unit opens the tray and displays a popup
message that prompts you to insert a disc.
9
Enter or edit the text.
Use the F1-F4 (cursor) keys to select a character
to edit, then use the JOG/DATA dial to change the
character.
You can also input characters using a keyboard
connected to the PS/2 connector.
10 After you edit the text, press the ENTER key.
After you delete the data on a CD-RW disc, or
if you have inserted a blank CD-R/RW disc, the
DV-RA1000HD displays a popup message that
requests confirmation for writing to the CD.
Repeat the procedure from step 11.
The DV-RA1000HD displays a popup message
that requests confirmation for writing the data to
the CD.
11 Press the ENTER key.
The write operation starts.
If you have inserted any other disc, the unit
opens the tray and displays a popup message that
requests that you insert a disc.
When the write operation is complete, a message
appears, asking whether you wish to create an-
other audio CD using the same source files.
If you do not wish to create another audio CD,
press the CANCEL key.
12 To create another audio CD, press the ENTER
key.
The DV-RA1000HD initiates a procedure to quit
copy mode.
During this procedure, the DV-RA1000HD dis-
plays a progress bar. When the procedure is
complete, then displays the home screen.
The DV-RA1000HD automatically opens the tray.
Insert a destination CD into the tray, then press
the ENTER key.
The DV-RA1000HD retracts the tray, then starts
to check the disc.
Copying tracks from a CD to the HD
You can copy the tracks on a CD into a 44.1kHz/24-bit
project on the HD of DV-RA1000HD. The tracks are
copied in BWF format.
For more information, see “Selecting a copy
3
4
Use the F1 and F2 keys to select a project into
which you wish to copy the tracks.
Copy IDs on a CD are used for tracks in the project
play list. If copy-prohibited tracks are copied onto
the HD as BWF files, you will be unable to edit these
tracks (that is, you will be unable to divide or combine
these tracks), nor can you copy them to a CD-R/RW
disc.
After selecting a project, press the ENTER key.
The DV-RA1000HD displays in the source track
selection screen a list of all tracks on the CD. (Note
that tracks with Copy ID set to “Prohibit” will
not be included in the list.)
1
2
Select CD to HD in the copy menu screen.
Insert a copy source CD following the instruc-
tions on the screen.
The DV-RA1000HD displays a destination proj-
ect selection screen that includes a list of projects
that are in 44.1 kHz format on the HD.
Figure 7.11: List of tracks on the CD
5
Select the tracks you wish to copy.
To select a highlighted track, press the F1 (SELECT)
key. The selected track is marked with a check
mark to the left of its name.
Press the F1 key again to deselect the check-
marked tracks.
Figure 7.10: Selecting a copy destination project
TASCAM DV-RA1000HD
ꢃꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
7 − Copy function
To select all tracks, press the F2 (ALL SEL.) key.
mode, F3 and F4 keys to move the cursor, and the
JOG/DATA dial to select a character.
To deselect all selected tracks, press the F3
(ALL REL.) key.
You can also input characters using a keyboard
connected to the PS/2 connector.
6
When you finish selecting tracks, press the ENTER
key.
8
When you finish editing the text, press the ENTER
key.
The DV-RA1000HD displays a screen that en-
ables you to edit the name of the files that will be
duplicated in the specified project.
The unit displays a message that requests confir-
mation for copying tracks to the HD.
If a file in the HD uses the same name as the
selected source file, the DV-RA1000HD displays a
duplicate file screen that lists all files that use the
same name. Follow the procedure in the “Same
project name in the destination” section to re-
solve the name duplicate issues, then press the
ENTER key.
Figure 7.12: File name
•
If you press the CANCEL key, instead of the
ENTER key in Step 9, the DV-RA1000HD
returns to the source track selection screen.
The default file name is
“YYYYMMDD_hhmm_TT.wav”. (YYYY: year;
MM: month; DD: date; hh: hour; mm: minute;
TT: track number)
You cannot change the track number or exten-
sion (.wav).
9
Press the ENTER key.
The CD tracks are copied into the HD.
After the copy operation is complete, the
DV-RA1000HD initiates a procedure to quit copy
mode.
•
If you press the CANCEL key, instead of the
ENTER key in Step 6, the DV-RA1000HD
returns to the destination project selection
screen.
During this procedure, the DV-RA1000HD dis-
plays a progress bar. When the procedure is com-
plete, the unit automatically displays the home
screen.
7
Edit the file names.
Use the F1 and F2 keys to change the input
ꢃꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
8 − Effects
The DV-RA1000HD incorporates two signal proces-
sors: a 3-band equalization stage and a dynamics pro-
cessor. These can be inserted either before the final
recording process or on playback.
Equalization is carried out a 40-bit resolution, and
dynamics processing is carried out at 32-bit resolution
at the same sampling frequency as the current project.
NOTE
These effects can be used on playback to simulate the
effects of pre-mastering effect processing before the
mixed stereo track is actually pre-mastered in another
facility, or may be even used to perform the actual pre-
mastering.
The effects are not available in Sampling Frequency
1ꢅꢄ.ꢂ kHz, 1ꢇꢀ kHz, and DSD modes.
Setting up the effect position
The EFFECT key is used to switch the effects on and
off, to set up the parameters, and to set up the position
of the effect in the signal chain.
0 dB to –72 dB and INF(full cut). Settings
between 0 and –10 dB are made in 0.5 dB
steps, settings from –10 dB onwards are
made in 1 dB steps.
Press and release the key to turn the effect chain on and
off (the indicator shows the status).
•
The EQ section can be switched ONor OFF
(EQ SW).
Press, hold and release the key to bring up the first set-
ting screen:
The next section cannot be set, but shows the
level of the signal before the dynamics pro-
cessor.
•
•
The dynamics processor can be switched ON
or OFF(DYN SW).
The next section cannot be set, but shows
the level of the signal immediately before the
output level control.
Figure 8.1: Effect setting screen
•
•
Finally, the output level following the
dynamics processor can be set (OUT LVL), using
the same parameters as the input level set-
ting.
Use the F3 and F4 keys to move the cursor, and the
JOG/DATA dial to set values. From left to right:
•
The effect insertion position can be set to be
on playback or recording (PLAYor REC).
Press ENTER to confirm the settings (or
CANCEL to cancel them).
•
The input level to the effect processor section
can be attenuated (IN LVL) with settings from
Equalization
The equalization effect has three bands: a shelving
sweepable low, a fully parametric mid, and a shelving
sweepable high.
•
•
Pressing the F3 (BAND) key cycles between the
LOW, MID and HIGH bands.
Use the F1 (up) and F2 (down) keys to select
the GAIN and FREQ (frequency) parameters and
the Q parameter for the MID band.
All bands can cut or boost ±12 dB. The slope of the low
and high bands is 6 dB/octave.
•
Use the JOG/DATA dial to change the values.
As the values change, the response curve
changes to give a visual indication of the EQ
setting.
1
From the effect setting screen (see Figure 8.1, Ef-
fect setting screen), press the F1 (EQ) key.
2
Press F4 (SW) to switch the EQ effect on and off.
When the effect is turned on, the response curve
is filled solid, as in the figure here (it is hollow
when the effect is turned off).
Figure 8.2: EQ setting screen
TASCAM DV-RA1000HD
ꢃꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
8 − Effects
NOTE
•
The output level from the EQ effect (which
feeds the dynamics processor) is shown by
the meters at the right of the response curve.
Since each band is capable of boosting the level by
1ꢀ dB in the digital domain, you should take care
not to overload the outputs.
3
Press ENTER to confirm these settings.
Dynamics processor
The dynamics processor has a number of settings avail-
able:
2
3
The first parameter, TYPE, allows you to select the
type of dynamics processor, as explained above:
CMPx3, EXPx3, CMPx1, EXPx1.
• Three-band compressor
• Three-band expander
• Single-band compressor
• Single-band expander
On this screen, use the F1 and F2 keys (up and
down) and the JOG/DATA dial to set the crossover
points for the dynamics bands (this only has an
effect when CMPx3or EXPx3is selected).
These two frequencies cannot overlap.
The frequencies of the two crossover points of the
three-band effects can be set (the slope of the filters is 6
dB/octave).
If CMPx1is selected, the MAKE UP (makeup gain)
parameter can be turned ONor OFFhere.
4
Press F3 (BAND) to make the settings for the dy-
namics processor. For CMPx3and EXPx3
settings, repeated presses of the F3 key cycle
through LOW, MID and HIGH bands. There is only
one setting screen and one set of parameters,
named SINGLE, for the single-band processors.
The dynamics processor always comes after the EQ
effect.
1
Figure 8.3: Dynamics crossover screen
Dynamics Attack &
setting release
Gain
reduction
Output
level
Input level
Threshold
Gain
Figure 8.4: Dynamics processor band settings
•
•
•
THRESHOLD: The input signal level at which the
compressor/expander starts to operate.
5
For each band of the processor, the following
parameters are available (the screen shows the
setting, and in many cases, a graphic changes to
reflect the changes made to the parameter val-
ue). Use the F1 and F2 keys to navigate, and the
JOG/DATA dial to change values.
RATIO: The ratio between the original and pro-
cessed signal levels.
KNEE: The shape of the change before and
after the signal reaches the threshold level.
ꢃꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
8 − Effects
The slowest slope is set by the value “5.”
•
RELEASE: The time the processed signal takes
to return to unprocessed after the input sig-
nal falls below the threshold (compressor) or
exceeds the threshold level (expander).
•
•
GAIN: The output level of the signal processed
by the compressor/expander.
ATTACK: The time the processed signal takes
to achieve the specified ratio after the input
signal exceeds the threshold (compressor) or
falls below the threshold (expander).
6
Use F4
and off.
(SW) to turn the dynamics processor on
7
Press ENTER to confirm these settings.
Effect libraries
The DV-RA1000HD effect libraries, located on the HD,
enable you to store and recall effect (EQ and dynamics)
settings that can be shared by all projects.
The EQ and dynamics libraries are each divided into
two categories: a preset library that contains preset
data, and a user library that can store user-defined set-
tings. The EQ library and dynamics library can each
store up to 99 sets of preset or user library data.
The EQ library and dynamics library each feature a
preset library that stores preset data and a user library
that can store user-defined settings.
Recalling library data
Follow the steps below to recall stored preset data or
user data.
1
While the EQ setting screen (or dynamics setting
screen) is displayed, press and hold the ENTER
key for at least one second.
The DV-RA1000HD displays the EQ library
screen (or dynamics library screen).
Figure 8.6: Dynamics library screen
NOTE
To return to the EQ setting screen (or dynamics set-
ting screen) while the EQ library screen (or dynam-
ics library screen) is displayed, press the CANCEL
key.
2
Move the cursor to the desired library data you
want to recall.
Figure 8.5: EQ library screen
3
Press the F2 (LOAD) key.
The DV-RA1000HD applies the recalled library
data to the effect parameters, then displays the
EQ setting screen (or dynamics setting screen).
Storing library data
You can store the current effect settings as user data.
2
Move the cursor to the library data location to
which you want to store the current settings.
1
While the EQ setting screen (or dynamics setting
screen) is displayed, press and hold the ENTER
key for at least one second.
NOTE
You cannot store the settings to the preset data
location.
The DV-RA1000HD displays the EQ library
screen (or dynamics library screen).
3
Press the F1 (SAVE) key.
The DV-RA1000HD stores the current parameter
settings as the selected library data, then dis-
plays the EQ setting screen (or dynamics setting
screen).
NOTE
To return to the EQ setting screen (or dynamics set-
ting screen) while the EQ library screen (or dynamics
library screen) is displayed, press the CANCEL key.
TASCAM DV-RA1000HD
ꢃꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
8 − Effects
Naming library data
You can change the name of user library data.
•
You can use up to 20 characters for a library
data name.
1
While the EQ library screen (or dynamics library
screen) is displayed, press the F3 or F4 key to
enter library name edit mode.
3
When you finish editing the name, press the
ENTER key.
You can now move the cursor to individual char-
acters.
The edit is confirmed, and the EQ library screen
(or dynamics library screen) is displayed.
•
To cancel the edit and return to the EQ
library screen (or dynamics library screen),
press the CANCEL key, instead of the ENTER
key.
2
Following the instructions in “Naming files,
projects, marks, etc.” on page 29, edit the library
data name.
ꢃꢆ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
9 − Use with a computer
The DV-RA1000HD will work with the following
Microsoft operating systems: Windows 2000 and
Windows XP.
CAUTION
You should always follow your computer’s instruc-
tions on how to disconnect a USB removable drive
safely from your system. If you do not do this, there
It will work with the following operating systems from
Apple Computer: MacOS 9.2.2 and above, and MacOS
X 10.2 and above.
is a risk of data corruption on your computer.
For all the above operating systems, no driver is
required. The HD of DV-RA1000HD simply appears as
a USB mass storage device.
Connecting the DV-RA1000HD to a computer
Only use a high-quality cable certified for use with
USB 2.0 systems.
2
A popup menu on the DV-RA1000HD screen asks
you if you want to connect to the computer. Press
ENTER (or CANCEL to cancel).
NOTE
The DV-RA1000HD appears as a mass storage unit (on
some Microsoft systems, it may initially appear as an
“unrecognizable device”; this will also happen if the
DV-RA1000HD is not in USB mode when it is con-
nected to a PC).
• You can use the DV-RA1000HD with USB 1.1 sys-
tems, but the performance will necessarily not be
as good as with a USB ꢀ.0 system.
• Avoid connecting the DV-RA1000HD to a com-
puter using a USB hub. Always connect the
DV-RA1000HD and computer directly.
All front panel controls are disabled (except the
CANCEL key (see below). Use the computer’s system to
eject a disc.
1
Press MENU and select USB. Press ENTER.
Disconnecting from Windows 2000 / XP systems
With Windows 2000 and Windows XP, the procedure
is a little more complex than simply unplugging the
DV-RA1000HD.
1
Left-click this icon to show a popup bar. Click
this popup bar to allow the DV-RA1000HD to be
removed from the computer.
In the system tray (typically at the bottom right of the
screen), you see an icon picture of a PC card and an
arrow.
Figure 9.1: Disconnecting the DV-RA1000HD
2
Follow the instructions below on disconnecting.
(See “After “ejecting” from the computer” be-
low.)
Disconnecting from Mac OS X systems
When you are disconnecting the DV-RA1000HD from
a Macintosh system (OS 9 or OS X), drag the disk icon
to the Trash, or press Command-E (OS X 10.3 also has
a button in the Finder which allows ejecting removable
media).
When the icon has disappeared from your desktop, you
can disconnect the DV-RA1000HD as described below.
After “ejecting” from the computer
When you have used the computer operating system to
“eject” or disconnect the DV-RA1000HD from the sys-
tem:
2
3
A popup appears. Press ENTER to completely dis-
connect the DV-RA1000HD, or CANCEL to halt
the disconnection process.
1
Press CANCEL to start the disconnection process.
When the popup disappears, you can disconnect
the cable from the computer.
TASCAM DV-RA1000HD
ꢃꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
9 − Use with a computer
Transferring audio files
You can transfer audio files (BWF or DSDIFF format)
between a computer and the HD of DV-RA1000HD via
a USB connection.
When the play list is being restructured, the
transferred BWF file might be converted to a
different format to suit the unit. In this case,
the converted file may lose some information
specific to the application that created the
BWF-format file.
•
After you transfer a computer’s file to the
HD of DV-RA1000HD, you must add the file
to the play list on the HD by restructuring
the play list. (See “Restructuring the play
Transferring files between a DVD disc and a computer
In addition to transferring audio files between a com-
puter and the HD, you can transfer audio files (in the
BWF or DSDIFF format) between a DVD±RW disc
(formatted with the DV-RA1000HD) and a computer,
by inserting the DVD±RW disc into the DVD drive of
the computer.
When the play list is being restructured, the
transferred BWF file might be converted to a
different format to suit the unit. In this case,
the converted file may lose some information
specific to the application that created the
BWF-format file.
•
After you transfer a computer’s file
to DVD±RW disc formatted with the
DV-RA1000HD, you must add the file to the
play list on the DVD±RW by restructuring
the play list. (See “Restructuring the play
•
You can also transfer audio files from
a DVD±R disc that was created by the
DV-RA1000HD in copy mode to a computer.
ꢄ0
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
10 − Specifications, etc.
Analog I/O
Balanced inputs
Connector:
3-pin XLR female x 2 (1: GND, 2: Hot, 3: Cold)
Input impedance
Nominal input level
Maximum input level
> 10 kΩ @ 1 kHz
+6 dBu (at max. +15 dBu), +4 dBu (at all other levels)
+15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu (switchable)
Unbalanced inputs
Connector
Unbalanced RCA pin jacks x 2
> 10 kΩ @ 1 kHz
–10 dBV
Input impedance
Nominal input level
Maximum input level
+6 dBV
Balanced outputs
Connector
3-pin XLR male x 2 (1: GND, 2: Hot, 3: Cold)
220 Ω
Output impedance
Nominal output level
Maximum output level
+6 dBu (at max. +15 dBu), +4 dBu (at all other levels)
+15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu (switchable)
Unbalanced outputs
Connector
Unbalanced RCA pin jacks x 2
Output impedance
Nominal output level
Maximum output level
220 Ω
–10 dBV
+6 dBV
Phones output (stereo)
Connector
1/4 " stereo jack (T = L, R = R, S = GND) x 1
Max output power
80 mW + 80 mW (30 Ω)
Digital I/O
PCM inputs (XLR)
Connector:
3-pin XLR female x 2 (1: GND, 2: Hot, 3: Cold)
IEC-60958-4, AES-3-1992
Signal type
Input frequencies (kHz)
44.1/48, 88.2/96 (double-speed or double-wire), 176.4/192 (double-speed + double-wire)
all 6%
Data format
16-bit (44.1 kHz, CD-DA), 24-bit (PCM recording to DVD RW or HD)
Input impedance
Nominal input level
Minimum signal level
Intrinsic jitter
110 Ω 20%
2–7 Vpp
200 mVpp
<0.025UI (4 ns @ 48 kHz)
PCM inputs (RCA)
Connector:
RCA (pin) jack x 1
Signal type
IEC-60958-3
Input frequencies (kHz)
Data format
44.1/48, 88.2/96 (double-speed ), all 6%
16-bit (44.1 kHz, CD-DA), 24-bit (44.1 kHz/48 kHz, 88.2/96 kHz to DVD RW or HD)
Input impedance
Nominal input level
Minimum signal level
Intrinsic jitter
75 Ω 20%
0.5 Vp-p
0.2 Vp-p
<0.025UI (4 ns @ 48 kHz)
TASCAM DV-RA1000HD
ꢄ1
Download from Www.Somanuals.com. All Manuals Search And Download.
10 − Specifications, etc.
DSD inputs (BNC)
Connector
BNC connectors x 2
Signal type
Sony SDIF-3 format / DSD-Raw
Signal level
2 V to 5 V (equivalent to 5V TTL)
Input impedance
Clock synchronization
75 Ω, 10%
Must be synchronized to 44.1 kHz at WORD SYNC IN or use internal clock at 44.1 kHz
PCM outputs (XLR)
Connector:
3-pin XLR male x 2 (1: GND, 2: Hot, 3: Cold)
IEC-60958-4, AES-3-1992
Signal type
Output frequencies (kHz)
44.1/48, 88.2/96 (double-speed or double-wire), 176.4/192 (double-speed + double-wire)
all 6%
Data format
16-bit (44.1 kHz, CD-DA), 24-bit (PCM recording to DVD RW or HD)
Output impedance
Nominal output level
Intrinsic jitter
110 Ω 20%
2–5 Vpp
<0.025UI (4 ns @ 48 kHz)
PCM outputs (RCA)
Connector:
RCA (pin) jack x 1
Signal type
IEC60958-3
Output frequencies (kHz)
Data format
44.1/48, 88.2/96 (double-speed ), all 6%
16-bit (44.1 kHz, CD-DA), 24-bit (44.1 kHz/48 kHz, 88.2/96 kHz to DVD RW or HD)
Output impedance
Nominal output level
Intrinsic jitter
75 Ω 20%
0.5 Vpp (typical)
<0.025UI (4 ns @ 48 kHz)
DSD outputs (BNC)
Connector
BNC connectors x 2
Signal type
Sony SDIF-3 format / DSD-Raw
Signal level
2 V to 5 V (equivalent to 5V TTL)
Output impedance
Clock synchronization
10 Ω
Must be synchronized to 44.1 kHz at WORD SYNC IN or use internal clock
Other connections
WORD SYNC IN
Connector
BNC
Input voltage
5 V TTL equivalent
Input impedance
75 Ω 10%, with THRU automatically engaged
WORD SYNC OUT
Connector
BNC
Input voltage
5 V TTL equivalent
Input impedance
Sampling frequencies (kHz)
< 10 Ω
44.1, 48, 88.2, 96, 176.4, 192 (PCM) / 44.1 (DSD)
WORD SYNC THRU
Connector
BNC
Output voltage
5 V TTL equivalent
< 10 Ω
Output impedance
USB 2.0
USB 2.0 Hi-speed Female B-type connector for connection to personal computer
ꢄꢀ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
10 − Specifications, etc.
CONTROL I/O (serial) connector
Connector
‘D’-sub 9-pin female
Control protocol
TASCAM optical disc control protocol a
RS-232C
Communication protocol
REMOTE IN (from RC-RA1000)
Connector
2.5 mm stereo mini-jack
KEYBOARD
Connector
Standard PS/2 mini-DIN connector
Compatibility
101-key (US) keyboard or 106-key (Japanese) PS/2 keyboard
a. Contact your TASCAM distributor for full details of how to use this connector if you wish to implement remote
control.
Audio performance
These figures all measure analog-to-analog performance.
Frequency response
All modes
20 Hz — 20 kHz ( 0.5 dB)
Fs = 88.2/96 kHz
DSD mode
at 40 kHz –1 dB ( 1 dB)
at 50 kHz –3 dB ( 1 dB)
at 70 kHz –3 dB (+1 dB/–2 dB)
Fs=176.4/192 kHz
Total Harmonic Distortion (typical)
PCM, DSD
0.004% (f=1 kHz, AES-17LPF, AD to DA)
Signal-to-noise ratio (typical)
ADC
DAC
110 dB (A-weighting, AES-17LPF, DVD recording)
120 dB (A-weighting, AES-17LPF, DVD recording)
Crosstalk
>97 dB, f=1 kHz, AES17-LPF, DVD RW/HD recording
<0 dB = –16 dBFS
Click noise
Difference between channel levels <1.0 dB, 1 kHz, 0 dBFS
Physical, etc. specifications
Voltage requirements
Power consumption
Dimensions (w x h x d)
AC100-240 V, 50/60 Hz
33 W
483 x 95 x 357 (mm)
19 x 3.75 x 14.1 (in)
Weight
6.8 kg (15 lbs), excluding remote control unit
5°C to 35°C (41°F to 95°F)
Operating temperature
TASCAM DV-RA1000HD
ꢄꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
10 − Specifications, etc.
Dimensional drawing
483 mm
465 mm
435 mm
357 mm
331 mm
15 mm
11 mm
Figure 10.1: Dimensions of the DV-RA1000HD
ꢄꢂ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
10 − Specifications, etc.
Block diagram
Figure 10.2: Block diagram
TASCAM DV-RA1000HD
ꢄꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
ꢄꢄ
TASCAM DV-RA1000HD
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
TASCAM DV-RA1000HD
ꢄꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
»
DV-RA1000HD
TEAC CORPORATION
Phone: +81-422-52-5082
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
Printed in China
7733 Telegraph Road, Montebello, California 90640
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. De C.V
Phone: +52-555-581-5500
Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF
TEAC UK LIMITED
Phone: +44-8451-302511
Unit 19 & 20, The Courtyards Hatters Lane Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
|