Tascam CD Player CD 200BT User Manual

D01194420A

CD-200BT

CD Player / Bluetooth Receiver

OWNER'S MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

The apparatus draws nominal non-operating power

from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position.

The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

Caution should be taken when using earphones or

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can

cause hearing loss.

•

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

If you are experiencing problems with this product,

contact TEAC for a service referral. Do not use the prod-

uct until it has been repaired.

•

7 Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

CAUTION

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

Do not expose this apparatus to drips or splashes.

•

Do not place any objects filled with liquids, such as

vases, on the apparatus.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A ground-

ing type plug has two blades and a third grounding

prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not

ﬁt into your outlet, consult an electrician for replace-

ment of the obsolete outlet.

Do not install this apparatus in a confined space

such as a book case or similar unit.

The apparatus should be located close enough to

the AC outlet so that you can easily grasp the power

cord plug at any time.

If the product uses batteries (including a battery

pack or installed batteries), they should not be

exposed to sunshine, fire or excessive heat.

CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace

only with the same or equivalent type.

•

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recep-

tacles, and the point where they exit from the appa-

ratus.

RACK-MOUNTING THE UNIT

11 Only use attachments/accessories specified by the

manufacturer.

Use the supplied rack-mounting kit to mount the unit in a

standard 19-inch rack, as shown below.

Remove the feet of the unit before mounting.

12 Use only with the cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the appa-

ratus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from

tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

CAUTION

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

•

Leave 1U of space above the unit for ventilation.

Allow at least 10 cm (4 in) at the rear of the unit for

ventilation.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information

⁸CAUTIONS ABOUT BATTERIES

This product uses batteries. Misuse of batteries could

cause a leak, rupture or other trouble. Always abide by

the following precautions when using batteries.

⁸CAUTIONS ABOUT LASER RADIATION

This product has been designed and manufactured according

to FDA regulations “title 21, CFR, chapter 1, subchapter J, based

on the Radiation Control for Health and Safety Act of 1968,”and

is classified as a class 1 laser product. There is no hazardous

invisible laser radiation during operation because invisible laser

radiation emitted inside of this product is completely confined

in the protective housings.

Never recharge non-rechargeable batteries. The

batteries could rupture or leak, causing fire or injury.

•

When installing batteries, pay attention to the polarity

indications (plus/minus (+/–) orientation), and install

them correctly in the battery compartment as indicat-

ed. Putting them in backward could make the batteries

rupture or leak, causing fire, injury or stains around

them.

The label required in this regulation is shown at 1.

•

For U.S.A

When you store or dispose batteries, isolate their termi-

nals with insulation tape or something like that to prevent

them from contacting other batteries or metallic objects.

•

When throwing used batteries away, follow the dispos-

al instructions indicated on the batteries and the local

disposal laws.

Do not use batteries other than those specified. Do not

mix and use new and old batteries or different types of

batteries together. The batteries could rupture or leak,

causing fire, injury or stains around them.

Cautions:

DO NOT REMOVE THE PROTECTIVE HOUSING USING A

SCREWDRIVER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR

NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE

THE PRODUCT IN ITS DAMAGED STATE.

•

Do not carry or store batteries together with small

metal objects. The batteries could short, causing leak,

rupture or other trouble.

•

Do not heat or disassemble batteries. Do not put them

in fire or water. Batteries could rupture or leak, causing

fire, injury or stains around them.

•

If the battery fluid leaks, wipe away any fluid on the

battery case before inserting new batteries. If the

battery fluid gets in an eye, it could cause loss of

eyesight. If fluid does enter an eye, wash it out thor-

oughly with clean water without rubbing the eye and

then consult a doctor immediately. If the fluid gets on

a person’s body or clothing, it could cause skin injuries

or burns. If this should happen, wash it off with clean

water and then consult a doctor immediately.

Optical pickup

Type

: EP-C101

Manufacturer

: Eve r B r ight Te chn o l o g y an d S ci e n ce

Electronical Co.,LTD

: Less than 0.3 mW

: 790 25nm

: IEC60825-1: 2007

Laser output

Wavelength

Standard

The unit power should be off when you install and

replace batteries.

•

Remove the batteries if you do not plan to use the unit

for a long time. Batteries could rupture or leak, causing

fire, injury or stains around them. If the battery fluid

leaks, wipe away any fluid on the battery compartment

before inserting new batteries.

Do not disassemble a battery. The acid inside the

battery could harm skin or clothing.

•

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information

⁸For European Customers

Disposal of electrical and electronic equipment

Disposal of batteries and/or accumulators

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste

stream via designated collection facilities appointed

by the government or the local authorities.

(a) Waste batteries and/or accumulators should be

disposed of separately from the municipal waste

stream via designated collection facilities appointed

by the government or the local authorities.

(b) By disposing of the electrical and electronic

equipment correctly, you will help save valuable

resources and prevent any potential negative effects

on human health and the environment.

(b) By disposing of waste batteries and/or accumulators

correctly, you will help save valuable resources and

prevent any potential negative effects on human

health and the environment.

serious effects on the environment and human health

as a result of the presence of hazardous substances in

electrical and electronic equipment.

(d) The crossed out wheeled dust bin symbol indicates

that electrical and electronic equipment must be

collected and disposed of separately from household

waste.

lators can have serious effects on the environment

and human health as a result of the presence of

hazardous substances in batteries and/or accumu-

lators.

(d) The crossed out wheeled dust bin symbol indicates

that batteries and/or accumulators must be collected

and disposed of separately from household waste.

If the battery or accumulator contains more than

the specified values of lead (Pb), mercury (Hg), and/

or cadmium (Cd) defined in the Battery Directive

(2006/66/EC), then the chemical symbols for lead (Pb),

mercury (Hg) and/or cadmium (Cd) will be indicated

beneath the crossed out wheeled dust bin symbol.

(e) The return and collection systems are available to

the end users. For more detailed information about

disposal of old electrical and electronic equipment,

please contact your city office, waste disposal service

or the shop where you purchased the equipment.

Pb, Hg, Cd

(e) The return and collection systems are available to

the end users. For more detailed information about

disposal of waste batteries and/or accumulators,

please contact your city office, waste disposal service

or the shop where you purchased them.

For China

“仅适用于海拔 2000m 以下地区安全使用”

“仅适用于非熱帯气候条件下安全使用”

产品

机种：CD-200BT 有毒有害物质或元素

六价铬

有毒有害物质或元素的名称及含量

铅

汞

镉

多溴联苯

多溴二苯醚

品

名

(Pb)

○

(Hg)

○

(Cd)

○

(Cr6+)

○

(PBB)

○

(PBDE)

○

CHASSIS 部份

FRONT PANEL 部份

螺丝部份

○

线材部份

○

PCB Assy 部份

CD MECH 部份

○

电源

部份

○

附

属品

部份

○

LABEL 部份

装部份

包

○ ：表示该有毒有害物质在该部件所有均质材料中的含有量均在 SJ/T11363-2006 标准规定的限量要求以下。

× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

（针对现在代替技术困难的电子部品

及合金中的铅 )

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Setting the program .................................................20

Checking the program.............................................21

Replacing a program track .....................................21

Adding more program tracks................................22

Clearing the program ...............................................22

Repeat playback................................................................22

Time and text information display .............................23

Pitch control........................................................................24

Intro Check function........................................................24

1 – Introduction ......................................................................7

Features..................................................................................7

Included items .....................................................................7

Conventions used in this manual..................................7

Trademarks............................................................................8

Precautions for placement ..............................................8

Power supply........................................................................8

Beware of condensation...................................................8

Cleaning the unit.................................................................8

About discs............................................................................9

Handling of compact discs.......................................9

Bluetooth overview............................................................9

Transmission conditions............................................9

Profiles .............................................................................9

Codecs..............................................................................9

Content protection......................................................9

Transmission security .................................................9

5 – Bluetooth device playback.................................25

Pairing ...................................................................................25

Searching for Bluetooth devices .................................25

Controlling Bluetooth devices .....................................25

Playback from Bluetooth devices................................25

Bluetooth information display .....................................26

Deleting pairing information........................................26

6 – Message Lists..................................................................27

Operation messages........................................................27

Warning messages ...........................................................27

Error messages...................................................................27

2 – Names and functions of parts..........................10

Top panel .............................................................................10

Rear panel............................................................................ 11

Display...................................................................................12

Remote control unit (TASCAM RC-CD200BT)..........12

7 – Troubleshooting..........................................................28

8 – Specifications.................................................................29

Ratings ..................................................................................29

Input and output ratings................................................29

Analog audio input....................................................29

Analog audio output ratings..................................29

Digital audio output ratings...................................29

Audio performance..........................................................29

Backup memory ................................................................29

Bluetooth .............................................................................29

General .................................................................................30

Dimensions .........................................................................30

3 – Preparations....................................................................14

Making connections ........................................................14

Connecting a device to the AUX IN jack ...................15

Preparing the remote control.......................................15

Inserting batteries......................................................15

Replacing the batteries............................................15

Cautions about the use of batteries....................15

Cautions about using the remote control.........15

Loading a CD ......................................................................16

Selecting the audio to output (current source)......16

4 – CD playback.....................................................................17

Playable discs and files ...................................................17

Folders and tracks on data CDs ...................................17

Playback area .....................................................................18

Setting the playback area .......................................18

Playback modes.................................................................18

Selecting the playback mode................................18

Playback................................................................................19

Selecting a track................................................................19

Skipping to the next or previous track...............19

Selecting by track number .....................................19

Search forward and backward.....................................20

Folder playback (data CDs)............................................20

Setting the playback folder....................................20

Programmed playback....................................................20

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

1 – Introduction

Thank you for your purchase of the TASCAM CD-200BT CD Player

/ Bluetooth Receiver.

Included items

Before connecting and using the unit, please take time to read

this manual thoroughly to ensure you understand how to

properly set up and connect the unit, as well as the operation

of its many useful and convenient functions. After you have

finished reading this manual, please keep it in a safe place for

future reference.

This product includes the following items.

Take care when opening the package not to damage the items.

Keep the packing materials for transportation in the future.

Please contact TASCAM if any of these items are missing or have

been damaged during transportation.

You can also download the Owner's Manual from the TASCAM

web site (http://tascam.com).

•

Main unit ................................................................................................. 1

Wireless remote control unit (RC-CD200BT) .............................. 1

AA batteries............................................................................................ 2

A rack-mounting screw kit................................................................ 1

Warranty card ........................................................................................ 1

Owner's Manual (this manual)......................................................... 1

Features

•

Plays back audio CDs (CD-DA) and data CDs (CD-ROM/R/

RW) with WAV, MP3 and MP2 format files.

•

2U rack mount size

Analog (RCA) and digital (coaxial and optical) outputs

Headphone output with level control

TASCAM RC-CD200BT remote control with number (0–9)

buttons included

Displays CD text and ID3 tag information (including artist,

album and track names)

4 playback modes (continuous, single, random and

program)

Repeat playback function can be turned ON and OFF

Playback area can be designated for data CDs (ALL PLAY or

FOLDER)

CD playback pitch control function ( 14%)

Intro check function

Time can be displayed as track elapsed time, track

remaining time or total remaining time for audio CDs and as

track elapsed time for data CDs

CD drive has 10-second shockproof memory (protection

against skipping).

Built-in Bluetooth® audio receiver enables output of audio

from computers and portable audio devices that support

Bluetooth (A2DP)

In addition to SBC, Bluetooth (A2DP) supports AAC and

aptX® decoding, enabling the reception of high-quality

audio

Bluetooth (A2DP) also supports SCMS-T, enabling the

reception of protected audio content

Conventions used in this manual

In this manual, we use the following conventions:

•

Buttons, connectors and other parts of the unit and external

devices are indicated like this: DISPLAY button

•

Text displayed on the display of the unit and external

devices appears like this: ON

•

CD-DA format discs are sometimes called “audio CDs.”

CDs that contain audio files in MP2, MP3 or WAV formats are

called “data CDs.”

•

Audio CDs and data CDs are sometimes generically called

“CDs”.

MP3, MP2 and WAV files are sometimes generically called

"audio files".

The currently selected audio source is called the "current

source".

•

The currently selected folder is called the “current folder”.

The currently selected file is called the “current file”.

A computer, portable audio device or other equipment that

is connected to this unit by Bluetooth is called a "Bluetooth

device".

•

Additional information is provided as necessary as tips,

notes and cautions.

•

TIP

•

These are tips about how to use the unit.

Stereo line mini jack enables audio input from portable

audio players that do not support Bluetooth

NOTE

These provide additional explanations and describe special

cases.

CAUTION

Failure to follow these instructions could result in injury,

damage to equipment or lost recording data, for example.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

1 – Introduction

Trademarks

Precautions for placement

•

TASCAM is a registered trademark of TEAC Corporation.

The operating temperature should be between 5°C and

35°C (41°F and 95°F).

Make sure that the unit is mounted in a level position for

correct operation.

The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of

such marks by TEAC CORPORATION is under license.

•

and the aptX logo are trade marks of CSR plc or one of its

group companies and may be registered in one or more

jurisdictions.

Do not place any object on the unit for heat dissipation.

Avoid installing this unit on top of any heat-generating

electrical device such as a power amplifier.

Power supply

Connect the unit to the standard power outlet. Hold the plug

when connecting and disconnecting the power cord.

•

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

Other company names, product names and logos in this

document are the trademarks or registered trademarks of

their respective owners.

Beware of condensation

If the unit is moved from a cold to a warm place, or used

immediately after a cold room has been heated or otherwise

exposed to a sudden temperature change, condensation could

occur. Should this happen, leave the unit for one or two hours

before turning the unit on.

Any data, including, but not limited to information,

described herein are intended only as illustrations of such

data and/or information and not as the specifications for

such data and/or information. TEAC Corporation disclaims

any warranty that any use of such data and/or information

shall be free from infringement of any third party’s intel-

lectual property rights or other proprietary rights, and

further, assumes no liability of whatsoever nature in the

event of any such infringement, or arising from or connected

with or related to the use of such data and/or information.

Cleaning the unit

To clean the unit, wipe it gently with a soft dry cloth. Do not

wipe with chemical cleaning cloths, paint thinner, ethyl alcohol

or other chemical agents to clean the unit as they could damage

the surface.

Once every five years, please contact the retailer where you

purchased the unit or a TASCAM service center for internal

cleaning. If the unit is not cleaned for a long time and dust is

allowed to accumulate inside it, fire or malfunction could result.

Cleaning is more effective when conducted before the humid

season. Please check with us about the cost of internal cleaning.

This product is designed to help you record and reproduce

sound works to which you own the copyright, or where

you have obtained permission from the copyright holder or

the rightful licensor. Unless you own the copyright, or have

obtained the appropriate permission from the copyright

holder or the rightful licensor, your unauthorized recording,

reproduction or distribution thereof may result in severe

criminal penalties under copyright laws and international

contact your legal advisor. Under no circumstances will TEAC

Corporation be responsible for the consequences of any

illegal copying performed using the recorder.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

1 – Introduction

Moreover, the use of a wireless LAN (IEEE802.11b/g) or

About discs

In addition to audio CDs (CD-DA), the CD-200BT can play CD-R

and CD-RW discs on which audio CD, MP3, MP2 or WAV format

files are recorded. The CD player can also play 3-inch CDs.

microwave oven in the same operating environment could also

interfere with Bluetooth transmission. If this occurs, stop using

that equipment or move this unit and the Bluetooth device at

least 10 m away from it.

Profiles

Handling of compact discs

Always place the compact discs in the trays with their label

facing upward.

To remove a disc from its case, press down on the center of

the disc holder, then lift the disc out, holding it carefully by

the edges.

This unit supports the following Bluetooth profiles.

•

A2DP (Advanced Audio Distribution Profile)

AVRCP (Audio/Video Remote Control Profile)

Bluetooth devices must support A2DP in order to transmit audio

via Bluetooth.

Bluetooth devices must support AVRCP in order to enable

playback control via Bluetooth.

Even if they have the same Bluetooth profile, however, different

Bluetooth devices can have different functions depending on

their specifications.

Do not touch the signal side (the unlabeled side).Fingerprints,

oils and other substances can cause errors during playing.

To clean the signal side of a disc, wipe gently with a soft dry

cloth from the center towards the outside edge. Dirt on discs

can lower the sound quality, so clean them and always store

them in a clean state.

•

Do not use any record spray, anti-static solutions, benzine,

paint thinner or other chemical agents to clean CDs. This

could damage the delicate playing surface and cause CDs to

become unplayable.

Do not apply labels or other materials to discs. Do not use

discs that have had tape, stickers or other materials applied

to their surface. Do not use discs that have sticky residue

from stickers, etc. Such discs could become stuck in the unit

or cause it to malfunction.

Never use a commercially available CD stabilizer. Using stabi-

lizers with this unit will damage the mechanism and cause it

to malfunction.

Do not use cracked discs.

Only use circular compact discs. Do not use non-circular

promotional, etc. discs.

•

Codecs

This unit supports the following A2DP codecs and automatically

selects one of them during audio transmission.

•

SBC

AAC

aptX

It will select the appropriate A2DP codec to use according to the

codec support of the Bluetooth device and transmission condi-

tions.

•

NOTE

•

You cannot use buttons, for example, to select the A2DP

codec.

Due to the nature of Bluetooth wireless technology, playback

from this unit will start slightly later than when triggered from

the Bluetooth device.

Content protection

This unit supports SCMS-T content protection during audio

transmission, enabling the playback of protected audio.

Some record companies sell copy-protected discs or copy-

controlled discs that may not play back correctly in this unit.

Since such discs may not conform with the CD standard, do

not use them in this unit.

If you experience problems with such non-standard discs,

you should contact the producers of the disc.

•

Transmission security

This unit supports security functions during Bluetooth trans-

mission according to the Bluetooth standards, but the invisibility

of transmission is not guaranteed.

Our company will take absolutely no responsibility if data is

leaked during Bluetooth transmission.

Bluetooth overview

This unit has a built-in Bluetooth audio receiver, allowing it to

output the audio playback of a computer or portable audio

device that supports Bluetooth. In addition, this unit can be

used to control the playback of such Bluetooth devices.

CAUTION

Operation and connection of this unit's Bluetooth functions

with all Bluetooth devices are not guaranteed.

Transmission conditions

This is a Class 2 Bluetooth transmission output device. It has an

approximate transmission range of 10 m, but this distance can

vary due to the interference of obstacles and electromagnetic

waves.

An obstacle between this unit and another Bluetooth device

could interfere with Bluetooth transmission. If this occurs,

remove the obstacle.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

2 – Names and functions of parts

Top panel

seconds. Press this button again briefly during this time

to change the device to be connected by Bluetooth. (See

“Searching for Bluetooth devices ”o n page 25.)

Press and hold this button to start Bluetooth pairing mode.

Press and hold this button when in pairing mode to end

pairing mode. (See “Pairing ”o n page 25.)

1 POWER switch

Press this switch to turn the unit on or off.

CAUTION

•

Before turning the power on, minimize the volume of

connected equipment. Failure to do so could cause sudden

loud noises, which might harm your hearing, for example.

0 Display

•

Do not wear headphones when turning the power ON/OFF.

Noise could damage speakers or your hearing.

Displays various information.

q Remote Sensor

2 Disc tray

Insert discs (CD, CD-R, CD-RW) here.

When operating the remote control unit (RC-CD200BT),

point it towards here.

3 OPEN/CLOSE button

w DISPLAY [SHIFT] button

Use to open and close the disc tray.

You can change the time and other information shown on

this display.

4 PLAY/PAUSE button

When this button is pressed, the type of information

currently displayed is shown for two seconds. Press the

button again during this time to change the type of infor-

mation shown. The information that can be shown depends

on the current source, type of media and the status of

operation. (See “Time and text information display ”o n page

23.) (See “Bluetooth information display ”o n page 26.)

Press this button at the same time as another button to use

its shift function, which is shown as black letters on a white

background beneath the button.

Press during playback to pause. When playback is stopped or

paused, press to start playback.

5 STOP button

Press this button to stop playback.

Press this button when editing a program to clear all items

added to the program. (See “Setting the program ”o n page

20.)

6 SEARCH m/,[.//] buttons

Press briefly to select tracks (skip). Press and hold to search a

track.

7 PHONES jack and knob

Use this standard stereo jack to connect stereo headphones.

Use a plug adapter when connecting headphones with

mini-plugs. Use the PHONES knob to adjust the headphone

output level.

CAUTION

Use the PHONES knob to minimize the volume before

connecting headphones. Failure to do so could cause a

sudden burst of loud noise, which might result in hearing

damage, for example.

8 AUX IN jack

Use this stereo mini jack for line level audio input.

Connect a portable digital audio player or other external

audio device to it.

CAUTION

Before connecting an external device to the AUX IN jack,

minimize the volume of that device. Failure to do so could

result in sudden loud noises that could, for example, harm

your hearing.

9 DEVICE SEL/PAIRING button

Press this button briefly to show the name of the device

connected (or ready to be connected) by Bluetooth for two

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

2 – Names and functions of parts

Press and hold this button during playback or when stopped

to use the intro check playback function. The first 10 seconds

of each track on the CD will be played back one after the

other. During intro check playback, press and hold this

button again to return to the previously active playback

mode and continue playing back the current track. (Se e “Intro

Check function ”o n page 24.)

While pressing and holding the DISPLAY [SHIFT] button,

press this button to turn the CD playback pitch control

function ON/OFF. (See “Pitch control ”o n page 24.)

e PLAY MODE/PLAY AREA [SOURCE SEL] button

Press briefly to change the playback mode.

The four playback modes are continuous, single, random

and program. (See “Playback modes ”o n page 18.)

Press and hold this button to select ALL PLAY or FOLDER

as the play area during data CD playback. (See “Setting the

playback area ”o n page 18.)

Press this button while pressing and holding the DISPLAY

[SHIFT] button to cycle through the current source options

in the following order.

CAUTION

The repeat setting can be changed when the current source

is Bluetooth, but this setting has no effect on Bluetooth

playback. Moreover, when using Bluetooth the intro check

function cannot be used.

Current source order

NOTE

AUX IN cannot be selected if nothing is connected to the

t FOLDER g/t [PITCH −/+] buttons

AUX IN jack.

Use these buttons when the current source is a CD and the

playback area is FOLDER to change the playback folder. (See

“Setting the playback folder ”o n page 20.)

CAUTION

The playback mode and playback area settings can be

changed when the current source is Bluetooth, but these

settings have no effect on Bluetooth playback.

Use these buttons when the current source is a CD and the

playback area is ALL PLAY to skip between folders.

Press this button while pressing and holding the DISPLAY

[SHIFT] button to set the pitch control value. (See “Pitch

control ”o n page 24.)

r REPEAT/INTRO CHECK [PITCH] button

Press to turn the repeat playback function ON/OFF. (See

“Repeat playback ”o n page 22.)

Rear panel

NOTE

y ANALOG OUTPUT (UNBALANCED) jacks

These jacks output analog signals (Standard output: –10

dBV) of the CD or Bluetooth playback signal or the signal

input through the AUX IN jack.

•

Audio from Bluetooth playback and audio input through

the AUX IN jack can only be output as analog signals. These

audio sources cannot be output as digital signals.

•

The sampling frequency of this unit’s digital output is always

44.1 kHz regardless of the playback file sampling frequency.

Digital output is possible when the pitch control function is

on with CD, but the sampling frequency is changed by an

amount proportional to the pitch control value.

u DIGITAL OUTPUTS (COAXIAL) jack

This jack outputs the CD playback signal in S/PDIF digital

format.

i DIGITAL OUTPUTS (OPTICAL) jack

This jack outputs the CD playback signal in S/PDIF digital

format.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

2 – Names and functions of parts

Display

Remote control unit (TASCAM

RC-CD200BT)

icon

Shows the status of connection with a Bluetooth device.

Indicator

Blinking

Lit

Meaning

Unconnected

Connected

Blinking rapidly Currently pairing

2 Playback mode indicator

This shows the current playback mode.

Indicator Playback mode

None

Continuous playback mode

Single playback mode

Random playback mode

Program playback mode

SNGL

RAND

PROG

3 REPEAT indicator

REPEATappears when the repeat playback function is ON.

4 FOLDER indicator

FOLDERappears when the playback area is set to FOLDER

5 INTRO indicator

INTROappears when the intro check function is ON.

6 Current source indicator

This shows the current source.

Indicator

Current source

^BLUETOOTHBluetooth

AUX (-AUX-appears in the

main display area)

None

7 Main display area

1 Number (0–9) buttons

The track number and time or text information is shown.

Use these buttons to input numbers for track selection. (See

“Selecting by track number ”o n page 19.)

Track numbers have a maximum of 2 characters for audio

CDs and a maximum of 3 characters for a data CDs.

The status of the unit (OPEN, CLOSE, TOC

READ, etc.)

and messages (NO DISC, etc.) are also shown. Items with

more than eight characters are scrolled when shown.

* TOC means “Table Of Contents,”which is track information

written on the disc

2 PLAY AREA button

Press to set the playback area of data CDs to ALL PLAY or

FOLDER. (See “Setting the playback area ”o n page 18.)

8 Main display information type indicator

When text information is shown in the main display area,

these indicate the type of information.

3 INTRO CHECK button

Use for intro check playback. The first 10 seconds at the

beginnings of tracks on the CD will be played back one after

another.

During intro check playback, press and hold this button

again to return to ordinary playback mode. (See “Intro Check

function ”o n page 24.)

Indicator

ALBUM TITLE

Meaning

CD-TEXT album title or current folder

name

CD-TEXT album artist

CD-TEXT track title or track title of the

current file (from its tag data)

ALBUM ARTIST

TITLE

ARTIST

FILE

CD-TEXT track artist or track artist of

the current file (from its tag data)

Current file name

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

2 – Names and functions of parts

4 PLAY MODE button

t −/+ buttons

Press to change the playback mode.

Use these adjust the pitch control value during CD playback.

(See “Pitch control ”o n page 24.)

The four playback modes are continuous, single, random

and program. (See “Playback modes ”o n page 18.)

y STOP button

Press this button to stop playback.

CAUTION

Press this button when editing a program to clear all items

added to the program. (See “Setting the program ”o n page

20.)

The playback mode, playback area, and repeat settings can

be changed when the current source is Bluetooth, but these

settings have no effect on Bluetooth playback. Moreover,

when using Bluetooth the intro check function cannot be

used.

u PLAY/PAUSE button

Press during playback to pause. When playback is stopped or

paused, press to start playback.

5 REPEAT button

Press to turn the repeat playback function ON/OFF. (See

“Repeat playback ”o n page 22.)

6 SOURCE SEL button

Change the current source in the following order. (See

“Selecting the audio to output (current source)”o n page

16.)

Current source order

NOTE

AUX IN cannot be selected if nothing is connected to the

AUX IN jack.

7 PITCH button

Press this button to turn the CD playback pitch control

function ON/OFF. (See “Pitch control ”o n page 24.)

8 FOLDER g/t buttons

Use these buttons when the playback area is set to FOLDER

to change the playback folder. (See “Setting the playback

folder ”o n page 20.)

Use these buttons when the playback area is set to ALL

PLAYto skip between folders.

9 m/. and //, buttons

Press briefly to select tracks (skip). Press and hold to search a

track.

0 OPEN/CLOSE button

Use to open and close the disc tray.

q DISPLAY button

Press to change how the time is shown and other infor-

mation. When this button is pressed, the type of information

currently displayed is shown for two seconds. Press the

button again during this time to change the type of infor-

mation shown. The information that can be shown depends

on the current source, type of disc and status of operation.

(See “Time and text information display ”o n page 23.) (See

“Bluetooth information display ”o n page 26.)

w PAIRING button

Press and hold this button to start Bluetooth pairing mode.

Press and hold this button when in pairing mode to end

pairing mode. (See “Pairing ”o n page 25.)

e PROGRAM EDIT button

Use to set, confirm and edit programs. (See “Programmed

playback ”o n page 20.)

r DEVICE SEL button

The name of the device connected (or ready to be

connected) by Bluetooth is shown for two seconds. Press

this button again during this time to change the device to

be connected by Bluetooth. (See “Searching for Bluetooth

devices ”o n page 25.)

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

3 – Preparations

Making connections

Examples of connections that can be made with a CD-200BT are shown below.

Precautions before making connections

•

Before connecting other devices, read their operation manuals carefully and connect them properly.

Turn the power OFF or set the power to standby for this unit and all units to be connected to it.

Set up all the units so that they are powered from the same line. When using a power strip, for example, use a thick cable with a high

current capacity to reduce fluctuation of the power voltage.

DIGITAL

(OPTICAL)

DIGITAL

(COAXIAL)

ANALOG

(UNBALANCED)

Mixer,

Digital mixer,

Recorder,

Amplifier, or

other device

Digital recorder,

Digital amplifier, or

other device

Connecting analog audio devices

Connecting digital audio devices

Connect the analog output jacks of this unit to the input jacks

of a stereo amplifier, mixer, recorder or other device with analog

inputs.

Connect a digital output jack (coaxial or optical) of this unit

to the input jack of a stereo amplifier, mixer, recorder or other

device with a digital input.

NOTE

•

Cables are not included with this unit.

Do not bundle RCA cables with power cords or speaker

cables. Doing so could cause reduced audio quality or noise.

Bluetooth audio playback signals and AUX IN input signals

can only be output from the analog jacks. They cannot be

output from the digital connectors.

The sampling frequency of this unit’s digital output is always

44.1 kHz regardless of the playback media/file sampling

frequency.

During playback of CD, digital output is possible when the

pitch control function is in use, but the sampling frequency

is changed by an amount equivalent to the pitch control

value. When the pitch control function is on, some devices

might not be able to accept signals from the digital outputs

of this unit.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

3 – Preparations

Connecting a device to the AUX IN jack

By connecting the audio output of a portable music player or

similar device to the external input (AUX IN) jack, the audio from

that device can be output from this unit’s output jacks. The level

input through the AUX IN jack cannot be adjusted by this unit.

Adjust the output level of the external device.

CAUTION

•

Before connecting an external device to the AUX IN jack,

minimize the volume of that device. Failure to do so could

result in sudden loud noises that could, for example, harm

your hearing.

•

Before connecting to or disconnecting from the AUX IN jack,

change the current source to something other than AUX IN

(CD or Bluetooth), or turn this unit off.

Preparing the remote control

Inserting batteries

Cautions about using the remote control

•

When using other devices controlled by infrared rays, use of

this remote control might operate these devices by mistake.

1. Open the lid.

•

Use the remote control within the following range.

Remote Sensor

2. Confirm +/- polarity, and insert two AA batteries.

3. Close the lid.

Replacing the batteries

Replace both batteries with new ones when the range of the

remote control becomes short or if the function buttons become

unresponsive.

Cautions about the use of batteries

Misuse of batteries could cause them to leak, rupture or

otherwise be damaged. Please read and abide by the precau-

tions on them when using batteries. Also see “CAUTIONS ABOUT

BATTERIES ”o n page 4.

Operation distance

Directly in front: Within 7 meters

15° left or right: Within 7 meters

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

3 – Preparations

Loading a CD

To load a CD, press the OPEN/CLOSE button on the main unit or

on the remote control to open the disc tray, and put the CD into

the tray with the label facing up.

Press the OPEN/CLOSE button again to close the disc tray. After

loading the disc, the unit reads the disc’s information and the

display shows the total number of tracks and total playback time

if it is an audio CD or the total number of tracks in the current

folder or on the entire disc if it is a data CD.

Selecting the audio to output (current

source)

You can select the CD playback signal, the audio signal received

via Bluetooth or the signal input through the AUX IN jack as the

audio signal output from this unit.

Press the PLAY MODE/PLAY AREA [SOURCE SEL] button while

pressing and holding the DISPLAY [SHIFT] button on this unit,

or press the SOURCE SEL button on the remote control to cycle

through the current source options as shown below.

NOTE

Cycle through the current source options in the following order.

Current source order

•

When the current source is set to CD, instead of pressing the

OPEN/CLOSE button to close the disc tray, you can press

the PLAY/PAUSE button to close the disc tray and begin

playback immediately.

•

If you open the disc tray while this unit is in use, the

following settings are lost.

– Program

– Current folder (for data CDs)

Display when current source is CD

Display when current source is Bluetooth

Display when current source is AUX IN

NOTE

•

AUX IN cannot be selected if nothing is connected to the

AUX IN jack.

•

When the current source is changed from CD to Bluetooth,

the CD will stop if playing back or paused. When the current

source is changed from Bluetooth to AUX IN, playback of the

connected Bluetooth device will stop.

•

Even if the current source is changed, the CD playback mode,

current folder and program contents will not be erased.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

In this chapter, we explain playback functions that can be used

with tracks on CDs.

Folders and tracks on data CDs

The following explanations assume that a CD that contains

audio files/tracks has been loaded in this unit, the power is ON

and the CD has been set as the current source. (See “Selecting

the audio to output (current source)”o n page 16.)

This unit treats all the audio files on data CDs as “tracks”.

Some data CDs store files inside folders in the same way that

computers usually do. In addition, multiple folders can be

stored inside another folder creating a multilevel structure. (The

maximum number of folder levels is 16.)

You can use this unit’s folder search function to look for audio

files among multiple folders. Searching starts from high-level

folders and then moves to lower-level subfolders.

If there are audio files in the root directory of a data CD, this root

directory is also treated as a folder.

Folders that do not directly contain audio files will be ignored

when searching folders. For example, folders C and D in the

illustration below would be ignored when searching folders.

Playable discs and files

This unit can play back the following types of discs and files.

CD-DA (audio CD) format discs

Music CDs that are commercially available and CD-R and CD-RW

discs that have been recorded as audio CD format can be played.

In this manual, these types of discs are called “audio CDs.”

(Folder 01)

ROOT

Data CDs

This unit can play back CD-ROM/R/RW discs with MP3, MP2 and

WAV files in ISO 9660 Level 1, Level 2 and Joliet formats. In this

manual, these types of discs are called, “data CDs.”

(Folder 02)

NOTE

(Folder 03)

•

This unit cannot read CD-R/RW discs that have not been

finalized.

bb001.mp3(Track 001)

bb002.mp3(Track 002)

For details about playable sampling frequencies and bit

rates, see “Playback file formats” on page 29.

The sampling frequency of this unit’s digital output is always

44.1 kHz regardless of the playback disc/file sampling

frequency. Digital output is possible when pitch control is

ON, but the sampling frequency is altered in proportion to

the pitch control value. When the pitch control function is

ON, therefore, some equipment might not be able to receive

the digital output of this unit.

(No folder number)

cc001.txt(File other than audio)

aa001.mp3(Track 001)

(No folder number)

•

This unit’s display can only show single-byte characters

(alphabet and numbers). File with names that use Japanese,

Chinese or other double-byte characters can be played back,

but those characters will be shown as _on the display.

This unit identifies MP3 and MP2 files by their “.mp3” and

“.mp2” file extensions. This unit cannot play MP3/MP2

files that do not have the correct “.mp3” and “.mp2” file

extension, so always include these file extensions at the

ends of MP3/MP2 file names. This unit cannot play files that

are not in the MP3/MP2 data format even if they have an

“.mp3” and “.mp2” file extension.

(Folder 04)

ee001.mp3(Track 001)

00001.mp3(Track 001)

00002.mp3(Track 002)

Example of data CD structure

•

The unit identifies WAV files with the ".wav" file extension.

This unit cannot play WAV files that do not have the ".wav"

file extension, so always include the ".wav" file extension at

the end of the name of an WAV file. The unit cannot play files

that are not in the WAV data format even if they have the

".wav" file extension.

•

Data CDs with more than 999 files or 512 folders might not

play correctly.

Depending on disc conditions, this unit might not be able to

play some discs, or skips in the sound might occur.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

Playback area

Playback modes

With data CDs, you can set the area to be used for playback (PLAY

AREA setting). Follow the procedures below to set the playback

area.

This unit can play back tracks using the following four playback

modes.

Continuous playback mode (default setting)

Tracks on the CD are played back in numerical order.

Setting the playback area

Press and hold the PLAY MODE/PLAY AREA [SOURCE SEL]

button on the main unit or press the remote control PLAY AREA

button to set the playback area.

NOTE

When FOLDERis the playback area for a data CD, the

tracks in the current folder will be played back in numerical

order.

Single playback mode

The selected track on the CD is played back once and then

playback stops.

Random playback mode

The tracks on the CD are played back in random order regardless

of their track numbers. Playback stops after all tracks have been

played.

NOTE

When FOLDERis the playback area for a data CD, the

tracks in the current folder will be played back in random

order. (See “Folder playback (data CDs)” on page 20.)

Program playback mode

The programmed tracks are played back in program order. See

“Programmed playback ”o n page 20 for details.

Selecting the playback mode

The selected playback area is shown as follows in the main

display area for about two seconds and then disappears.

Depending on the selected playback area, the FOLDER

indicator might also appear on the display.

Press the main unit PLAY MODE/PLAY AREA [SOURCE SEL]

button or the remote PLAY MODE button to cycle through the

playback modes. During playback, however, you can only switch

among continuous, single and random playback modes.

To select programmed playback, press the main unit PLAY

MODE/PLAY AREA [SOURCE SEL] button or the remote PLAY

MODE button when playback is stopped.

The currently selected playback mode is shown on the display as

follows.

Main

FOLDER

Meaning

display area indicator

All files on the data CD will be played

back.

All files in the selected folder on the

data CD will be played back.

ALL ^PLAYNot shown

FOLDER

Shown

Indicator

No indicator

SNGL

Playback mode

Continuous playback mode

Single playback mode

Random playback mode

Program playback mode

RAND

PROG

The selected playback mode is retained even when the

power is turned off.

NOTE

Immediately after pressing the PLAY MODE/PLAY AREA

[SOURCE SEL] button on the main unit or the PLAY MODE

button on the remote control, the selected mode is shown

on the main display area as follows.

Continuous playback mode set:

CONTINUE

Single playback mode set:

SINGLE

Random playback mode set:

RANDOM

Programmed playback mode set:

PROGRAM

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

Playback

Selecting a track

The following procedures assume that the necessary connec-

tions have been completed, the unit’s power has been turned

ON and CD has been loaded.

There are two ways to select a track. You can move (skip) to the

previous or next track, or you can select a track directly by its

track number.

To start playback, press the PLAY/PAUSE button on the main

unit or the remote control.

Skipping to the next or previous track

Use the main unit SEARCH m/, [.//] buttons or

the remote search (m/. and //,) buttons to skip to

tracks.

After selecting the track, press the PLAY/PAUSE button on the

main unit or the remote control to start track playback.

Stopping playback

Press the STOP button on the main unit or the remote

control.

Pausing playback

Press the PLAY/PAUSE button on the main unit or the

remote control.

NOTE

If you press the main unit SEARCH m/,buttons or the

remote search (m/.and //,) buttons during

playback, playback will resume after skipping tracks.

In this manual, unless stated otherwise, explanations are given

assuming that the playback mode is continuous. (See “Playback

modes ”o n page 18.)

Selecting by track number

Use the number (0–9) buttons on the remote control to directly

select tracks for playback.

Track numbers can have up to two digits for audio CDs and up

to three digits for data CDs.

1. Use the number (0–9) buttons on the remote control to

input the track number. Enter the track number starting from

the largest digit.

To select track 1:

Press the 1 button one time.

To select track 12:

Press the 1 button followed by the 2 button.

2. Press the PLAY/PAUSE button on the main unit or the

remote control. The selected track begins to play.

If you press the STOP button on the main unit or the remote

control, the display stops showing the track number input

and the display returns to its previous state.

NOTE

•

When the playback area is set to ALL PLAY, use the

FOLDER g/t buttons on the main unit or the remote

control to skip between folders.

•

When in program or random mode, you cannot use the

number (0–9) buttons to select tracks.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

Search forward and backward

Programmed playback

You can search forward and backward in a track while

listening to it.

To use programmed playback, you must set a program either

before or after setting the playback mode to programmed

playback mode. (See “Selecting the playback mode ”o n page

18.)

1. Play or pause the desired track.

2. Press and hold a SEARCH m/, [.//] button on

the main unit or a search (m/. or //,) button on

the remote control to start searching forward or backward.

3. Release the button that you are holding to stop searching

and return the unit to the state it was in before searching

(playback or pause).

When in programmed playback mode, press the PLAY/PAUSE

button on the main unit or the remote control to start playback

of the set program in order from the first track (program step

01).

Press the main unit SEARCH m/, [.//] button or

the remote search (m/. or //,) button to skip to the

previous or next program step.

When playback is stopped in program playback mode using an

audio CD, the total number of tracks in the program and the

total program time are shown.

NOTE

Searching forward and backward is possible with sources

other than audio CDs.

When using a data CD, only the program number is shown.

Folder playback (data CDs)

NOTE

•

To select programmed playback, when stopped, press the

main unit PLAY MODE/PLAY AREA [SOURCE SEL] button

or the remote PLAY MODE button.

With data CDs, you can set the selected folder (current folder)

as the playback area. Follow the procedures below to set the

playback folder. You can also set the playback area to be all the

•

With data CDs, you cannot set a program when the

playback area is ALL PLAY. Change the playback area to

FOLDERto enable tracks in the current folder to be used in

the program.

tracks/files on the CD by selecting ALL PLAY

Setting the playback folder

1. Press and hold the PLAY MODE/PLAY AREA [SOURCE SEL]

button on the main unit or press the remote PLAY AREA

Setting the program

When no program is set, follow the procedures below to set a

program using the remote control.

button to set the playback area to FOLDER

2. Use the main unit FOLDER g/t [PITCH −/+] buttons or

the remote FOLDER g/t buttons to skip to the previous or

next folder.

NOTE

This will skip to the beginning of the first track in the

previous or next folder. If you hold down one of these

buttons, you can skip through folders continuously in order.

•

The program cannot be set from the main unit.

You can set a program at any time regardless of the current

playback mode.

NOTE

•

CD programs are cleared when the disc tray is opened or the

current folder is changed.

•

When you skip to a different folder, it becomes the current

folder.

1. Press the remote PROGRAM EDIT button when playback is

During folder playback, repeat playback will play back all

tracks inside the current folder repeatedly.

During folder playback, random playback will play back all

tracks inside the current folder randomly.

stopped.

The unit enters program setting mode. If no program has

been set, it will be possible to choose a track for program

step 01 (PROGindicator blinks).

Audio CD example

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

•

If you press the STOP button when the empty program step

where it is possible to add a track appears, all steps in the

program are cleared.

If you try to add more than 99 tracks, a PGM FULLerror

message appears. Only 99 tracks can be added.

Data CD example

Checking the program

You can check the contents of the program.

NOTE

If the program is already set, the track number of the track

set as program step 01 is shown.

1. Press the PROGRAM EDIT button on the remote control

while playback is stopped to put the unit into program

setting mode.

2. Use the remote number (0–9) buttons or search (m/.

and //,) buttons to select a track to set as program

step 01 (PROGand the track number blink).

The track number and playback time of the track set as

program step 01 is shown on the screen and PROGblinks.

(Playback time is not displayed when using a data CD.)

Use the number (0–9) buttons to input the number starting

with the largest digit.

Track number

Playback time

Track number

Playback time

2. Press the PROGRAM EDIT button to show the track infor-

Audio CD example

mation of the next program step.

3. If you press the PROGRAM EDIT button when the final

program step is shown, it becomes possible to add another

program step. (No track number is shown and PROGblinks.)

Data CD example

NOTE

4. Press the PROGRAM EDIT button again to exit the program

•

When using a data CD, the screen switches to file name

display if more than a second passes after pressing one

of the remote number (0–9) or search (m/.and

//,) buttons, but you can still add the track to the

program.

setting mode.

Replacing a program track

You can replace a track that has already been added to the

program.

•

If you press the STOP button while a track is selected,

selection of that track is canceled, and the screen returns to

the state where you can select a track.

1. Press the PROGRAM EDIT button on the remote control

while playback is stopped to put the unit into program

mode.

2. Follow the steps in “Checking the program”above and press

the PROGRAM EDIT button to show the program step with

the track that you want to replace.

3. Press the remote PROGRAM EDIT button to add the

selected track as program step 1.

3. Use the remote number (0–9) buttons or skip (m/.

and //,) buttons to select the desired track and press

the PROGRAM EDIT button.

After replacing a track, the display shows the empty step at

the end of the program and you can add another track to

the end of the program if desired.

4. The unit is now ready for you to add another track as the

next program step.

5. If you are finished adding tracks to the program, press the

remote PROGRAM EDIT button when the empty program

step is shown.

4. Press the PROGRAM EDIT button again to exit program

setting mode.

The unit exits program setting mode.

NOTE

•

The same track can be added to the program multiple times.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

Adding more program tracks

You can add tracks to the end of an already set program.

Repeat playback

You can play back all the tracks in the playback area repeatedly.

1. Press the PROGRAM EDIT button on the remote control

Press the main unit REPEAT/INTRO CHECK [PITCH] button or

the remote REPEAT button to turn the repeat playback function

ON/OFF.

while playback is stopped to activate program setting mode.

2. Press and hold the PROGRAM EDIT button until the empty

program step where it is possible to add a track appears. (No

track number is shown and PROGblinks.)

3. Use the remote number (0–9) buttons or skip (m/.

and //,) buttons to select the track to add and press

the PROGRAM EDIT button.

4. In this state, you can repeat step 3 to add more tracks, or

you can press the PROGRAM EDIT button to exit program

setting mode.

CAUTION

•

Although tracks can be added to the end of a program and

tracks can be replaced with different tracks, tracks cannot

be inserted into the middle of a program.

•

If you want to insert a track into the middle of the program,

replace and add program tracks to alter the program

contents.

Clearing the program

You can clear the entire program that has been set.

Repeat ON (REPEAT indicator appears)

All tracks are played back repeatedly.

1. Press the PROGRAM EDIT button on the remote control

while playback is stopped to activate program setting mode.

2. Press and hold the PROGRAM EDIT button until the empty

program step where it is possible to add a track appears. (No

track number is shown and PROGblinks.)

3. Press the remote STOP button.

-CLEAR-appears on the display. After clearing completes,

program setting mode resumes with the empty program.

Repeat OFF (no indicator)

Repeat playback is OFF.

In addition to the above procedure, opening the disc tray or

removing the disc also clears the program.

NOTE

•

NOTE

With data CDs, during folder playback all tracks within

the current folder will be played back repeatedly. During

program playback, all tracks within the program will be

played back repeatedly.

•

CD programs are cleared when the disc tray is opened or the

current folder is changed.

•

If the repeat playback function is turned ON during

playback, playback continues as is until the end and then

playback continues from the beginning.

•

If repeat playback is turned ON when stopped, repeat

playback begins when the PLAY/PAUSE button is pushed.

The repeat playback function’s ON/OFF state is retained

even when the power is turned OFF.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

NOTE

•

Time and text information display

For details about display when the current source is

Bluetooth, see “Bluetooth information display” on page

26.

After pressing the DISPLAY [SHIFT] button on the main unit

or the DISPLAY button on the remote control, the currently

selected type of information to be shown on the main

display appears for two seconds as follows.

You can set what type of time and text information is shown on

the display.

•

Press the DISPLAY [SHIFT] button on the main unit or the

DISPLAY button on the remote control to show for two seconds

the type of information (playback time or text information) that

is currently set to appear in the main area of the display. Press

this button again while this is being shown to change the type

of information displayed.

Track elapsed time:

ELAPSED

Track remaining time: REMAIN

The types of data that can be shown when changing the display

depend on the type and status of the current source or loaded

disc, as well as this unit’s operation status.

Total remaining time: T REMAIN

Album/track title:

Album/track artist:

File name:

TITLE

ARTIST

FILENAME

•

The text information shown on the display is CD text infor-

mation for audio CDs and ID3 tag information for data

CDs. When information is not included for a disc or file, NO

TITLE(title information) or NO NAME(artist information)

is shown. If the information contains characters that cannot

be displayed, those characters are replaced by _

•

When an audio CD is in programmed playback mode the

elapsed time and remaining time of the entire program is

shown.

The display contents setting is retained even when the

power is turned off.

Audio CDs with CD text

When playing back or paused, you can change the infor-

mation shown on the display, cycling through track elapsed

time, track remaining time, total remaining time, track title

and track artist.

When stopped, you can also change the information shown,

but the album title, album artist and total number of tracks

and total playback time are shown.

Audio CDs without CD text

When playing back or paused, you can change the infor-

mation shown on the display, cycling through track elapsed

time, track remaining time and total remaining time.

When stopped, you can also change the information shown,

but the total number of tracks and total playback time are

shown.

Data CD

When playing back or paused, you can change the infor-

mation shown on the display, cycling through track elapsed

time, track title, track artist and file name.

When stopped, you can still change the display mode from

the track elapsed time to the album title.

When stopped, you can switch to the album title (current

folder).

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

4 – CD playback

Pitch control

Intro Check function

Using pitch control playback, CDs can be played back at a

different pitch (sound frequency and playback speed).

Follow the procedures below to use pitch control playback.

When stopped or during playback press and hold the main unit

REPEAT/INTRO CHECK [PITCH] button or press the remote

INTRO CHECK button to play the first 10 seconds of each track

one after another. The INTROindicator appears when this

function is active.

During intro check playback, press and hold the REPEAT/INTRO

CHECK [PITCH] button on the main unit or the INTRO CHECK

button on the remote to return to ordinary playback mode

(INTROdisappears from the display).

1. Press the REPEAT/INTRO CHECK [PITCH] button while

pressing and holding the DISPLAY [SHIFT] button on the

main unit or press the PITCH button on the remote control

to turn pitch control ON. The current pitch control value is

shown at this time.

When using Intro Check, briefly press the main unit SEARCH

m/, [.//] buttons or the remote search

(m/. and //,) buttons to skip to the preceding

or next track.

Press the STOP button to stop Intro Check.

The intro check function can be used during program and

folder playback modes.

2. Use the FOLDER g/t [PITCH −/+] buttons while pressing

and holding the DISPLAY [SHIFT] button on the main unit

or use the PITCH –/+ button on the remote control to set the

pitch in 0.5% units in a range of 14.0%.

CAUTION

To turn pitch control playback OFF:

The intro check function cannot be used with Bluetooth.

Press the REPEAT/INTRO CHECK [PITCH] button while

pressing and holding the DISPLAY [SHIFT] button on the

main unit or press the PITCH button on the remote control.

NOTE

•

During playback, turning pitch control playback ON or OFF

might cause the playback sound to skip momentarily.

Using pitch control playback with a data CD (MP3, MP2,

WAV) sometimes causes the playback sound to skip.

When the pitch control function is on, digital output is

possible, but the sampling frequency will be changed by

an amount equivalent to the pitch control value. When the

pitch control function is on, some devices might not be able

to receive this unit’s digital output.

•

The pitch control function cannot be used with Bluetooth.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

5 – Bluetooth device playback

This unit can output audio from a computer, portable audio

Searching for Bluetooth devices

Using this unit, you can select one Bluetooth device that has

already been paired and only search for and connect with it

device or other equipment (Bluetooth device) that supports

Bluetooth (A2DP). Moreover, if the Bluetooth device supports

AVRCP, you can use this unit's PLAY/PAUSE button, for example

to control playback of the Bluetooth device

Press the DEVICE SEL/PAIRING button on the main unit or the

DEVICE SEL button on the remote control to show the name of

the currently connected Bluetooth device (or Bluetooth device

that is ready to be connected) on the display. It will blink for two

seconds

During this time, press the DEVICE SEL/PAIRING button on the

main unit or the DEVICE SEL on the remote control again to

change the Bluetooth device.

Pairing

Following these procedures to pair with a Bluetooth device in

order to communicate with it.

NOTE

Pairing also requires operating the Bluetooth device. For

instructions about how to do this, refer to the operation

manual for the Bluetooth device you are using.

NOTE

When an already paired Bluetooth device seeks to connect

with this unit, this unit will accept and connect with that

Bluetooth device if this unit is not already connected to

another Bluetooth device.

1. Press and hold the DEVICE SEL/PAIRING button on the main

unit, or press and hold the PAIRING button on the remote

control.

Controlling Bluetooth devices

If the connected Bluetooth device supports AVRCP, you can

control it using this unit or the included RC-CD200BT wireless

remote control.

PLAY/PAUSE button:

STOP button:

Play and pause

Stop

Skip (m/. and //,) buttons:

Select tracks and search

CAUTION

These might not function properly depending on the

connected Bluetooth device.

Playback from Bluetooth devices

After pairing with a Bluetooth device in advance, you can play

back audio from that device using the following procedures.

When you do this, PAIRINGappears blinking on the

display, and the icon blinks rapidly.

1. Press the PLAY MODE/PLAY AREA [SOURCE SEL] button

while pressing the DISPLAY [SHIFT] button on the main unit

or press the SOURCE SEL button on the remote control to

set the current source to Bluetooth.

2. The unit searches for the selected Bluetooth device (shown

on the display) and connects with it as soon as it finds it.

When connected, CONNECTappears on the display for two

seconds and the icon appears.

2. Prepare the Bluetooth device for Bluetooth transmission.

3. Select this unit (CD-200BT) from the Bluetooth device.

After doing this, you will be able to control the Bluetooth device

from this unit or the included RC-CD200BT wireless remote

control, as well as output the playback audio from the Bluetooth

device from this unit.

When pairing succeeds, PAIREDappears on the display

and the unit is connected to that device.

NOTE

•

After pairing once, pairing again is not necessary. The paired

Bluetooth device will be detected and connect automati-

cally.

This unit can store pairing data for a maximum of 8 devices.

If more than 8 devices are paired the oldest pairing data will

be overwritten with newer data.

While pairing, press the DEVICE SEL/PAIRING button on

the main unit or the PAIRING button on the remote control

to cancel pairing. CANCELEDwill appear on the display.

Some older Bluetooth devices require the input of a passkey

when pairing. If this is the case, enter 0000.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

5 – Bluetooth device playback

Bluetooth information display

Deleting pairing information

The icon on the display shows the connection status of the

Bluetooth device.

Use the following procedures to delete all pairing information

from this unit.

If you delete pairing information, connection with Bluetooth

devices will not occur.

icon status Connection status

1. Press the POWER switch to turn the unit off.

Blinking

Not connected (searching for Bluetooth device)

2. While pressing and holding the PAIRING button on the unit,

Not blinking Connected with Bluetooth device

press the POWER switch again to turn the unit on.

When the current source is Bluetooth, you can select the infor-

mation shown on the display (name of connected device or

connected (A2DP) codec.

When ERASINGappears on the display, release the

PAIRING button on the unit.

Press the DISPLAY [SHIFT] button on the main unit or the

DISPLAY button on the remote control to show the type of

information currently selected in the main display area for two

seconds.

During this time, press the DISPLAY [SHIFT] button on the main

unit or the DISPLAY button on the remote control again to

change the type of information shown.

After the pairing information is deleted, the unit begins

operation as normal.

The A2DP codec used for connection is displayed as one of the

following.

Not connected (searching)

SBC codec used

AAC codec used

aptX codec used

NOTE

•

After pressing the DISPLAY [SHIFT] button on the main unit

or the DISPLAY button on the remote control, the currently

selected type of display information is shown for two

seconds as follows.

Connected device name: DEV NAME

Connected A2DP codec:

CODEC

•

If the name of the connected device contains characters that

cannot be shown, _will appear in place of those characters.

If pairing has not been conducted (or pairing information

has been deleted), NO PAIRwill appear in place of the

connected device name and the connected A2DP codec.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

6 – Message Lists

Operation messages

Depending on the operation of the unit, the following messages will appear in the main display area.

Message

Meaning

Response

-AUX-

AUX IN is selected as the current source.

CANCELED An operation has been canceled.

-CLEAR-

All programs have been cleared.

The disc tray is closing.

CONNECT

ERASING

NO DISC

NO FILES

NO NAME

NO PAIR

NO TITLE

OPEN

The unit is connected with a Bluetooth device.

All pairing data is being erased.

There is no disc or the disc cannot be verified.

The data CD has no files that can be played back.

There is no artist data or no file data that can be displayed.

The unit is not paired with any Bluetooth device.

There is no title data that can be displayed.

The disc tray is open.

Load a disc that contains playable files.

PAIRED

Pairing has succeeded.

PAIRING

(Blinking)

Pairing is being conducted.

TOC READ A file is being processed. Do not remove the media.

Warning messages

If an operation cannot be completed, one of the following messages will appear for about two seconds and then disappear.

Message

NO PGM

Meaning

No program has been created.

Response

Add tracks to the program.

A program can contain a maximum of 99 tracks. Clear

tracks from the program and try again.

PGM FULL No more tracks can be added to the program.

Error messages

If one of the following error messages is shown, please refer to the Response column and try to resolve it. If you are still unable to correct

the problem, please contact the nearest retailer or TASCAM representative.

Message

Meaning

Response

BT ERR

(Blinking)

Communication with the Bluetooth receiver is not possible.

Contact the nearest retailer or TASCAM representative.

COMM ERR

(Blinking)

Cannot communicate with the CD drive.

Contact the nearest retailer or TASCAM representative.

COMM ERR An error occurred during communication with the CD drive.

DEC ERR

The file type is not supported or otherwise could not be played. Change the data CD.

The TOC or file system could not be read, or focus adjustment

was not possible.

DISC ERR

Clean or change the disc.

DRV ERR

READ ERR

The CD drive hardware is broken.

The track cannot be accessed.

Contact the nearest retailer or TASCAM representative.

Clean or change the disc.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

7 – Troubleshooting

If you have problems with your system, look through this

chart and see if you can solve the problem yourself before

calling the nearest retailer or TASCAM representative.

The unit cannot connect to the device or

transmission between them is disrupted.

e Confirm that the Bluetooth device’s power is on and that its

Bluetooth function is also on.

e Is the Bluetooth device too far from the unit? Is a wall or

other obstacle interfering with transmission?

If the Bluetooth device is behind this unit, the unit itself

could be blocking transmission.

No power

e Is the unit’s power plug completely inserted into a working

power outlet?

Change the positions of the Bluetooth device and this unit.

e Try turning this unit off and than on again.

Remote control doesn’t work.

e Delete the “CD-200BT”pairing from the Bluetooth device

and then follow the procedures in “Pairing”to pair with it

again.

e Check to see if the batteries are properly installed in the

remote control.

e If the batteries are dead, change the batteries.

Cannot pair with a device.

No sound

e Confirm that the Bluetooth device you want to pair with

supports A2DP and AVRCP.

e Check the connection to the monitor system again.

e Confirm that the Bluetooth device you want to connect with

is able to communicate. For details, refer to the operation

manual of that device.

e Check the volume and settings of the amplifier.

There is unwanted noise.

e Turn this unit and the Bluetooth device off once and on

again, and then try pairing them.

e Are the connecting cables all properly connected and

functioning?

e Turn off any other Bluetooth devices other than the one that

you are trying to pair with.

e Delete the “CD-200BT”pairing from the Bluetooth device

A CD cannot be played back.

and then try pairing again.

e If you are using a data CD with MP3 files, confirm that the file

bit-rates are compatible with this unit.

e Is the disc scratched or dirty?

I cannot play back all the files on a data CD.

e Make sure the unit is not in folder playback mode.

I cannot use program playback.

e Make sure the playback area is not set to ALL PLAY

To use program playback with data CDs, the playback area

must be set to FOLDER

The audio skips or there is noise.

e Is there a wireless LAN, another Bluetooth device, a

microwave oven or a similar device nearby? Use this unit as

far as possible from such devices.

e Reduce the distance between the Bluetooth device and this

unit when using them together. Try changing the positions

of the Bluetooth device and this unit.

e If you are using any applications on a smart phone other

than one for audio playback, the sound might skip. If this

occurs, stop the operation of applications other then the one

for audio playback.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

8 – Specifications

Ratings

Backup memory

The following settings are backed up even when the unit power

is turned off.

Supported disc types

CD, CD-R and CD-RW discs

•

Time and title display settings

Playback mode

Program (when CD loaded)

Current folder (when data CD loaded)

Current source

Repeat playback function setting (ON/OFF)

Pitch control ON/OFF (CD)

Pitch control value (CD)

(including 12cm, 8cm and multisession discs and discs

with CD text)

Playback file formats

CD-DA:

44.1kHz, 16-bit stereo

MP2: 32/44.1/48kHz, 32–384kbps (data CDs)

MP3: 32/44.1/48kHz, 32–320kbps, VBR (data CDs)

WAV: 8/16/32/11.025/22.05/44.1/12/24/48kHz, 16-bit

(data CDs)

Bluetooth pairing information (up to 8 devices)

Input and output ratings

Bluetooth

Analog audio input

Version:

Output class:

(approximate transmission distance:

Supported profiles:

Supported A2DP codecs:

Supported A2DP content protection:

3.0

Class 2

10m*)

A2DP, AVRCP

SBC, AAC, aptX

SCMS-T

AUX IN jack

Connector:

Reference input level: –20 dBV

Maximum input level: –4 dBV

3.5mm stereo mini jack

Input impedance:

22 kΩ

*The transmission distance is approximate. The trans-

mission distance could vary depending on the surrounding

environment and electromagnetic waves.

Analog audio output ratings

ANALOG OUTPUT (UNBALANCED)

Connector:

Output Impedance:

RCA pin jack

200 Ω

Reference Output Level: –10 dBV (0.32 Vrms)

Maximum Output Level: +6 dBV (2.0 Vrms)

PHONES output

Connector:

6.3 mm (1/4') Stereo Phone Jack

Maximum Output Level: 20 mW + 20 mW

(THD+N: 0.1%, 32Ω)

Digital audio output ratings

DIGITAL OUTPUT (COAXIAL)

Connector:

RCA Pin Jack

IEC-60958-3 (S/PDIF)

Compatible Signal Format:

DIGITAL OUTPUT (OPTICAL)

Connector:

TOS (JEITA RC-5720C)

IEC-60958-3 (S/PDIF)

Compatible Signal Format:

Audio performance

Frequency Response

20 Hz - 20 kHz 1.0 dB (during playback, JEITA)

Signal-to-Noise Ratio (S/N)

More than 90 dB (during playback, JEITA)

Total Harmonic Distortion

Less than 0.01% (during playback, JEITA)

Dynamic Range

More than 90 dB (during playback, JEITA)

Channel Separation

More than 90 dB (during playback, JEITA)

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

8 – Specifications

General

Power Requirement

Weight

AC 120 V, 60 Hz (U.S.A./Canada)

AC 230 V, 50 Hz (U.K./Europe)

AC 240 V, 50 Hz (Australia)

4.5 kg (9.92 lb)

Operating Temperature

5 to 35°C

Power Consumption

8 W (U.S.A./Canada/U.K./Europe)

9 W (Australia)

Inclination of installation

5° or less

Dimensions (W x H x D)

481 x 94.5 x 298 (mm) / 18.94 x 3.72 x 11.73 (in)

Dimensions

435mm

481mm

465mm

•

Illustrations and other depictions may differ in part from the actual product.

Specifications and external appearance may be changed without notification to improve the product.

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

TASCAM CD-200BT

Download from Www.Somanuals.com. All Manuals Search And Download.

CD-200BT

TEAC CORPORATION

http://tascam.jp/

http://tascam.com/

http://teacmexico.net/

http://tascam.eu/

Phone: +81-42-356-9143

1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan

TEAC AMERICA, INC.

Phone: +1-323-726-0303

7733 Telegraph Road, Montebello, California 90640 USA

TEAC MEXICO, S.A. de C.V.

Phone: +52-55-5010-6000

Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México

TEAC UK LIMITED

Phone: +44-8451-302511

Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire, WD18 8TE, UK

TEAC EUROPE GmbH

http://tascam.eu/

Phone: +49-611-71580

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

Toro Smoke Alarm 53720 User Manual
Toshiba Laptop X75 A7295 User Manual
Toshiba TV DVD Combo 22LV610U User Manual
Trek Bicycle Accessories Bicycle Computer User Manual
Tripp Lite TV Cables S455 010 User Manual
ViewSonic Projector VS12617 User Manual
Viking Access Systems Garage Door Opener UL 325 User Manual
Viking Refrigerator F20711A EN User Manual
VTech Crib Toy 3S User Manual
Vulcan Hart Fryer GRD35 ML 052080 User Manual