INSTRUCTION MANUAL
NETWORK
COMBINATION DOME CAMERA
N-CC2564
Thank you for purchasing TOA's Network Combination Dome Camera. Please carefully follow the
instructions in this manual to ensure long, trouble-free use of your equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
Do not expose the unit to rain or an environment where it may be
splashed by water or other liquids, as doing so may result in fire or
electric shock.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
WARNING
result in death or serious personal injury.
When Installing the Unit
• This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
• Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified
may result in fire or electric shock.
• Avoid installing the unit in unstable locations, such as on a rickety or slanted surface. Failure to do so may
result in the unit falling and possibly causing personal injury.
• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Only use the unit's dedicated mounting hardware. The use of mounting hardware not designated could result
in the unit falling and possibly causing personal injury.
• Do not use other methods than specified to install the unit. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Attach the safety wire to the unit. If not attached, the unit could fall off, resulting in personal injury.
• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so
may cause the unit to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded,
eventually causing the unit to fall off, which could result in personal injury.
• Do not mount the unit in locations exposed to constant vibration. The mounting screws and/or bolts may be
loosened by excessive vibration, potentially causing the unit to fall, which could result in personal injury.
When the Unit is in Use
• If any of the following irregularities occurs, immediately unplug the power plug from the AC outlet and inform
the shop from where the unit was purchased. Further using the unit may result in fire or electric shock.
· If you detect smoke or a strange smell coming from the unit.
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If the power supply cord is damaged (exposure of the core, disconnection, etc.)
· If no camera images are displayed on the monitor TV when the temperature of the camera unit is 0°C or
more.
• To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage
components inside the unit. Refer all servicing to your nearest TOA dealer.
• Do not insert, or drop metallic objects or flammable materials in the ventilation slots of the unit’s cover, as
this may result in fire or electric shock.
• Do not touch the unit during thunder and lightning, as this may result in electric shock.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
When Installing the Unit
• To avoid electric shocks, be sure to switch off the power before power supply wiring work. Failure to do so
may result in electrical shock.
• Leave the installation of the unit to your TOA dealer because the installation requires expert experience and
skills. If the unit falls, this could cause personal injures.
When the Unit is in Use
• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Switch off the power, and unplug the power supply plug form the AC outlet for safety purposes when
cleaning or leaving the unit unused for a long period of time. Doing otherwise may cause a fire, burn injury or
electric shock.
• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting brackets that could cause the unit to fall, possibly causing
personal injury.
• Contact your TOA dealer as to the cleaning. If dust is allowed to accumulate in the unit over a long period of
time, a fire or damage to the unit may result.
CU version complies with Part 15 of the FCC Rules.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Modifications
Any modifications made to this device that are not approved by TOA Corporation may void the authority
granted to the user by the FCC to operate this equipment.
2. LIST OF INCLUDED COMPONENTS AND PARTS
Check to be sure that the following components and parts are contained in the package:
Safety wire ......................................................................................................................... 1
Camera mounting screw (M4 x 8) ..................................................................................... 4
Category5 shielded coupler (female to female) ................................................................. 1
Extension connector (alarm input, AUX Contact output) .......................................... each 1
CD-ROM (Software decoder : N-SD2000, Manual (PDF)) ............................................... 1
Network Combination Dome Camera Installation Manual ................................................. 1
Software License Agreement ............................................................................................ 1
Network Camera System Installation Guide ...................................................................... 1
Note
The CD-ROM contains the Software Decoder, Software Decoder's Instruction Manual, Setting Manual,
N-DR2000 Status Monitoring Software, Instruction Manual and Installation Guide for N-DR2000 Status
Monitoring Software, Firmware, Adobe Acrobat Reader and DirectX.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. GENERAL DESCRIPTION
The N-CC2564 Network Combination Dome Camera can be connected directly to a LAN (10BASE-
T/100BASE TX). Since it can simultaneously transmit MPEG-4 and JPEG data, smooth moving images can
be monitored and high-definition still images can be monitored and recorded. The N-CC2564 can transmit
sub-band ADPCM or PCM quality voice.
TOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degree
horizontal rotation per second and a 23 times optical zoom lens Up to 255 arbitrary positions can be preset
and such preset positions can be instantaneously repeated.
4. FEATURES
• Digital signal processing realizes high resolution and high picture quality. The unit also features the video
memory that increases the electronic sensitivity up to 32 times and enables electronic zooming.
• The supplied software decoder permits the images to be monitored via the network.
• It is also equipped with Timer, Motion Detection, Auto-flip, Wide Dynamic, Black & White mode, 12 times
Electronic Zooming and Privacy Masking functions
5. HANDLING PRECAUTIONS
• Noise may appear on the monitor or preset camera positions may deviate with prolonged camera use. In
such cases, use the camera’s refresh function to automatically refresh settings and reestablish the home
position once a day or week, thus allowing any position deviation to be corrected. When correcting manually,
display the menu screen using the software decoder and execute "Initialize" on the "Maintenance" items.
• It is recommended that the unit be installed in locations where the temperature is under +40°C, as the
longevity of the unit may reduce with prolonged unit use under high temperature and high humidity.
• Do not direct the camera lens to the sun or strong lighting or light reflection. Exposure to direct sunlight could
cause the CCD's color filter to deteriorate, leading to image discoloration.
• Do not install the unit in locations exposed to constant vibration. The unit is not intended for vehicle use. Do
not install the unit in a vehicle or ship.
• Do not give vibration or shock to the unit, as doing so may cause unit breakdown, or damage.
• Avoid installing the unit on sea or shore, or in locations exposed to dust or corrosive gas, or extraordinary
combustible conditions, or in swimming pools where disinfectants are used.
• To prevent the unit falls off, be sure to hang the supplied safety wire first when installing the unit.
• The dome camera is designed solely for suspended installations. The camera or dome must be suspended
vertically with its dome facing downward. Use special care not to suspend it at a tilted angle.
• Shielded (STP) network cables must be used with this unit to ensure compliance with EMC standards.
• The unit is not equipped with a power switch. Perform power construction work so that the camera power
can be turned on and off remotely.
• The dome camera features built-in heat generating circuitry. Take care not to touch the internal parts marked
"Caution High Temperature" when working inside the camera during dome cleaning or maintenance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Installing the camera cables in close proximity to fluorescent lamps or other electrical appliances can
downgrade the picture quality.
• If there is a strong electric or magnetic field near the camera, such as television transmission antennas,
motors or transformers, this may distort or roll the monitor picture. In such cases, run the entire wiring route
through metal conduit tubing.
• Before applying the power to the camera, be sure to complete all connections between the camera and
related equipment.
• Avoid directly touching the dome surface, since camera picture quality could deteriorate if the dome cover
becomes smudged and dirty.
• To clean, be sure to first unplug the power plug from the AC outlet, then wipe with a dry cloth. When the unit
gets very dirty, use a cloth dampened in a neutral detergent. Never use benzene, thinner or chemically
processed towel as the unit's plastic or other parts may be deformed or discolored.
• When cleaning the dome cover, wipe lightly with a soft cloth. In this event, the cover could be scratched and
damaged if the dome is covered in dust or sand. When the cover is extremely dirty, it is highly recommended
that the cover be removed and that its outside surface be washed lightly with water. Since alcohol-based
detergents can turn the dome cover whitish, avoid using them, as camera picture quality could be severely
affected.
• When dust has settled on the unit's lens, lightly clean using a commercial camera blower or cleaning paper.
• Install cables so as to prevent their damage and provide ample cable slack if they need to be stretched taut.
• The IP address, subnet mask and gateway IP address must be set.
• Transmission to multiple receivers using the unicast function could result in a reduction in the frame rate.
• When using the multicast function, the network must be compatible with the multicast system.
• When a connection is established between the transmitter and multiple receivers, if the data rate requested
by each receiver differs, the transmission will be limited to the minimum set data rate.
• In transmission streaming mode, data is constantly transmitted from transmitter to network even when no
communications are performed between the two.
• Personal computers running Microsoft Windows XP are required when performing initial settings for the
Network Combination Dome Camera.
• TOA's software decoder does not support Macintosh or Unix operating systems.
MPEG-4 visual patent portfolio license
With respect to a Licensee offering MPEG-4 Video Decoders and/or Encoders the following notice shall be
given:
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (1) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”)AND/OR (2) DECODING
MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSE BY MPEG LA
TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA,LLC.
SEE HTTP://WWW.MPEGLA.COM.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. NOMENCLATURE
[ Front view ]
[ Top view ]
2
3
4
9
1
5
1
7
6
1
2 4 V 5 0 / 6 0 H z M a x . 1 6 A
m o d e l N - C C 2 5 6 4 C U
I O T N D O M E C A M E R A N E T W O R K C O M B I N A
10
8
9
(1) Power Cable
Connects to the power supply.
• Contact Output 2 (AUX2)
This relay contact output controls its connected
external device, depending on the camera
settings.
(2) Network Terminal (10BASE-T/100BASE-TX)
Connects to the 10BASET/100BASE-TX using
the supplied LAN adapter.
O F F
Open
Short
O N
Short
Open
NO
NC
-
-
COM
COM
(3) Video Output Terminal (VIDEO OUT)
Outputs the Video signals.
Rated maximum allowable voltage : 30 V DC
Maximum allowable current: 1 A
Contact life: 100,000 times
(4) Audio Input Terminal (red) / Audio Output
Terminal (white)
These terminals are comprised of a terminal that
receives line level signals and a terminal that
outputs signals received via a network.
[
]
[
]
OFF
ON
NO
NO
COM
NC
COM
NC
(5) Alarm Input Terminal
Used to receive alarm signals from sensors, etc.
(6) Contact Output Terminal
• Contact Output N1, N2
(7) Composite Cable
Cables from terminals (2)
this composite cable.
This open collector output allows the external
device connected to this terminal to control
other connected equipment via a network,
depending on the network settings.
-(6) are merged into
(8) Initialization Switch (INITIALIZE)
Used to initialize the network settings.
• Contact Output 1 (AUX1)
This open collector output allows the external
device connected to this terminal to control
other connected equipment, depending on the
camera settings.
(9) Reset Switch (RESET)
Used to restart the camera.
(10) Base Unit
(11) Camera Unit
7
Download from Www.Somanuals.com. All Manuals Search And Download.
[ Bottom view of Camera Unit ]
[ Top view of Camera Unit ]
18
17
13
16
14
15
12
(12) Safety Wire
Connects to the base unit.
(15) DIP Switch (SW2)
Used to perform various settings of the camera.
(Refer to p. 32; DIP Switch Settings.)
(13) DIP Switch (SW1)
Not used.
(16) COM SW *
(17) COM LED *
(18) COM PORT *
(14) DIP Switch (SW2)
Used to perform various settings of the camera.
(Refer to p. 32; DIP Switch Settings.)
* Parts (16)
-(18) are for maintenance purposes (firmware update) only. Avoid using these parts in normal use.
[ Bottom view of Base Unit ]
20
21
19
(19) READY LED (Green)
(21) ERROR LED (Red)
Flashes quickly when the camera is in initial
operation mode, and lights continuously while
the camera is operating. This LED also flashes
slowly during firmware rewrite.
Lights when a failure occurs and camera
operation stops. This LED extinguishes when
the camera is automatically restarted.
(20) BUSY LED (Yellow)
Flashes during communications.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. PRECAUTIONS WHEN INSTALLING THE UNIT
The Combination Dome Camera weight 2.0 kg. Select the heavy-duty
mounting surface that can structurally support the weight of the
camera. Doing otherwise may result in the unit falling and possibly
causing personal injury.
WARNING
Notes
• Mount the camera to a heavy-duty ceiling surface (such as concrete ceiling).
• When mounting directly to the ceiling (such as a double ceiling) not strong enough to support the weight of
the mounted camera, use the optional C-BC511A Ceiling Mounting Bracket.
• When installing the camera in the ceiling to hide it as much as possible, use the optional C-BC511U or
C-BC511U-S Flush Ceiling Mounting Bracket.
• When hanging the camera from the ceiling, use the optional C-BC511P Ceiling Suspension Bracket.
• When mounting the camera to a wall, use the optional C-BC511W Wall Mounting Bracket.
8. DIRECT CEILING MOUNTING
Use the C-BC511C or C-BC511C-S Ceiling Mounting Cover.
8.1. Mounting Example
[ Cable routing to the attic ]
[ Cable routing over the ceiling surface ]
1
1
Cut out this portion along the
perforated slot of the Base Unit
using nippers.
Perforated slot
9
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2. Mounting Procedures
1. Mount the base unit to the ceiling.
First fix two of the base unit mounting holes as shown below.
Since no mounting screws are supplied with the camera, prepare them separately.
Use screws with a nominal diameter of 4 mm and a length of over 25 mm.
Note: When routing cables over the ceiling surface, securely fix all 4 of the base unit mounting holes to the
ceiling.
Camera direction
Camera direction
Ceiling surface
Secure these two holes first.
(Base unit mounting holes)
Mounting screws
2. Release the lock on the hinged portion of the base unit, and connect the composite cable and power cable
to the base unit. (For details, please refer to p. 30; "CONNECTIONS.")
Ceiling surface
Open
Hinged portion
Open
3. Push up and lock the hinged portion of the base unit and secure the remaining two mounting holes.
Close
Mounting screws
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Perform DIP SW settings on the camera unit.
(For details, please refer to p. 32; "DIP Switch Settings.")
5. Attach the safety wire from the camera unit to the wire mounting hole of the base unit.
Wire mounting bracket
6. Align the positioning mark on the base unit with that on the camera unit.
Align the marks
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Align the positioning marks, then push the camera unit up into the base unit.
Push up
Screw section inside the base unit
is to be inserted into the oval hole
in the camera unit.
Note
Note
When mounting the camera unit to the base unit,
mount it straight till it is attached to the base unit
correctly. Mounting it at an angle may cause
damage to the camera unit.
Take care not to pinch the safety wire between the
camera unit and base unit to avoid damage to the
camera.
8. Turn the camera unit clockwise pushing it up to the base unit until it locks into place.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Tighten 2 camera unit mounting screws.
Tighten
10. Align the positioning mark on the ceiling mounting cover with that on the base unit.
Align the marks
Ceiling mounting cover
C-BC511C
C-BC511C-S
11. Turn the ceiling mounting cover clockwise pushing it up to the base unit until it locks into place.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9. MOUNTING THE CAMERA TO A WEAK CEILING PANEL
Use the optional C-BC511C or C-BC511C-S Ceiling Mounting Cover and the optional C-BC511A Ceiling
Mounting Bracket.
Notes
• Use the cover and the anchor whenever the space between suspended ceiling panel and upper ceiling
exceeds a height of 100 mm.
• The ceiling panel to which the camera will be mounted must be 9 - 40 mm in thickness.
• Be sure to use the supplied safety wire.
• Be sure to use the specified screws to mount the Network Combination Dome Camera and direct mounting
anchor, and ensure that they are securely mounted without any play.
Upper ceiling
100 mm or more
40 mm or less
Note
When routing the wiring from the
Ceiling panel
ceiling surface, the ceiling panel
must be 9 - 40 mm in thickness.
9.1. Mounting Example
Safety wire
(supplied with the C-BC511A)
Anchor bolt for celing mounting bracket
Upper ceiling
C-BC511A
Ceiling Mounting Bracket (optional)
Anchor bolt for safety wire
Ceiling panel
Network Combination Dome camera
C-BC511C, C-BC511C-S
Ceiling Mounting Cover (optional)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9.2. Mounting Procedures
1. Make a mounting hole of ø140 mm in the ceiling panel.
2. Install the anchor bolt for ceiling mounting bracket and anchor bolt for safety wire into the upper ceiling.
Notes
• The anchor bolt for ceiling mounting bracket must be aligned with the center of the mounting hole of ø140
mm in the ceiling panel, and must not project from the ceiling surface.
• If an existing anchor bolt is available nearby, it can be substituted for the anchor bolt for safety wire.
Upper ceiling
Anchor bolt for ceiling mounting bracket
Anchor bolt for safety wire
Ceiling surface
Ceiling panel
ø140 mm
3. Attach the supplied safety wire to the anchor bolt for safety wire.
4. Attach the ceiling mounting bracket to the end of the safety wire.
5. Attach the ceiling mounting bracket to the anchor bolt for ceiling mounting bracket.
Safety wire
Upper ceiling
Anchor bolt for ceiling
mounting bracket
3
C-BC511A
Ceiling Mounting Bracket
(optional)
5
Ensure close contact here.
*
Safety wire
(supplied with the C-BC511A)
4
C-BC511A
Ceiling Mounting Bracket
(optional)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Attach the supplied safety wire to the base unit.
Use screws M3 x 8
tightened to the base unit.
7. Attach the safety wire connected to the base unit to the ceiling mounting bracket.
8. For subsequent procedures, follow the steps 1 – 11 on p. 10 – 13.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10. FLUSH CEILING MOUNTING
• Use the optional C-BC511U or C-BC511U-S Flush Ceiling Mounting Bracket.
• Flush mounting can be used to reduce the camera's exposed area. Use the optional C-BC511U or C-
BC511U-S Flush Ceiling Mounting Bracket when mounting cameras to gypsum board ceilings or other weak
ceiling panel materials in which mounting screws cannot be securely inserted.
Notes
• Use the bracket whenever the space between suspended ceiling panel and upper ceiling exceeds a height
of 250 mm.
• The ceiling panel to which the camera will be mounted must be no more than 40 mm in thickness.
• Be sure to use the supplied safety wire.
• Be sure to use the specified screws to mount the Network Combination Dome Camera and flush ceiling
mounting bracket, and ensure that they are securely mounted without any play.
Upper ceiling
250 mm or more
40 mm or less
Ceiling panel
10.1. Mounting Example
Safety wire
(supplied with the C-BC511U
Anchor bolt for flush ceiling
mounting bracket
and C-BC511U-S)
Upper ceiling
C-BC511U or C-BC511U-S
Flush Ceiling Mounting Bracket
(optional)
Anchor bolt for
safety wire
Ceiling panel
Network Combination Dome camera
17
Download from Www.Somanuals.com. All Manuals Search And Download.
10.2. Mounting Procedures
1. Make a mounting hole of ø230 mm in the ceiling panel.
2. Install the anchor bolt for flush ceiling mounting bracket and anchor bolt for safety wire into the upper
ceiling.
• The anchor bolt for flush ceiling mounting bracket must be aligned with the center of mounting hole of
ø230 mm in the ceiling panel.
• Use the pattern paper supplied with the C-BC511U or C-BC511U-S bracket to determine the anchor bolt
length and mounting surface height.
• If an existing anchor bolt is available nearby, it can be substituted for the anchor bolt for safety wire.
Anchor bolt for flush ceiling
Anchor bolt for safety wire
Upper ceiling
mounting bracket
Mounting surface
Paper pattern
(supplied with the C-BC511U or C-BC511U-S)
Ceiling panel
ø230 mm
3. Attach the base unit to the flush ceiling mounting bracket.
First fix two of the base unit mounting holes as shown below.
(Use the machine screws supplied with the Network Combination Dome Camera.)
Machine screws M4 x 8
Camera direction
(supplied with the
Network Combination Dome Camera)
Camera direction
Camera front
Secure these two holes first.
(Base unit mounting holes)
Note: Route the cables from flush ceiling mounting bracket.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|