®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Belleta® iEA Series DC/DC Power Modules
48V Input, 25A Output
Eighth Brick
The Belleta Series offers an industry standard
eighth brick power module with true useable
power. Thanks to its low component count and
single-board open-frame design, it provides both
better electrical and thermal performance, and
lower cost than many other suppliers’ eighth brick
product offerings. Belleta® modules are perfect
for both next generation planning and cost
reduction design environments
Standard Features:
•
Size – 58.4mm x 22.9 mm x 8.8
•
UL 60950 (US and Canada), VDE
0805, CB scheme (IEC950), CE
Mark (EN60950)
ISO Certified manufacturing
facilities
mm (2.3 in. x 0.9 in. x 0.347 in.)
Thru-hole pins 3.68 mm (0.145”)
High efficiency – greater than 89%
1500Vdc isolation voltage
Meets basic insulation spacing
requirements
Constant switching frequency
Industry Standard Footprint
Output Voltage Adjustment
Remote on/off (positive logic)
Remote sense
Auto-recovering output over-
voltage protection
Auto-recovering output over-
current protection
Auto-recovering output short circuit
protection
Auto-recovering over-temperature
protection
•
•
•
•
•
•
Patented Design
Optional Features:
•
•
•
•
•
•
•
•
Remote on/off (negative logic)
Latching output over-voltage
protection
Short Thru-hole pins 2.79 mm
(0.110”)
Long Thru-hole pins 5.08 mm
(0.200”)
•
•
•
•
•
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
1/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Mechanical Specification:
Dimensions are in mm [in]. Unless otherwise specified tolerances are: x.x ± 0.5 [0.02], x.xx and x.xxx ± 0.25 [0.010].
1.02 [0.040] DIA Pin
1.57 [0.062] DIA Pin
2.03 [0.080] DIA Stand-Offs
2.59 [0.102] DIA Stand-Offs
6 Pins
2 Pins
Recommended Hole Pattern: (top view)
1
2
3
8
7
6
5
4
Pin Assignment:
PIN
1
FUNCTION
Vin(+)
PIN FUNCTION
4
5
6
7
8
Vo(-)
2
On/Off
Sense(-)
Trim
3
Vin(-)
Sense(+)
Vo(+)
Pin base material is brass with tin plating; the maximum module weight is 30.4g (1.07 oz).
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
3/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Absolute Maximum Ratings:
Stress in excess of Absolute Maximum Ratings may cause permanent damage to the device.
Characteristic
Min
-0.5
---
Max
80
Unit
Vdc
Vdc
Vdc
˚C
Notes & Conditions
Continuous Input Voltage
Transient Input Voltage
Isolation Voltage
100
1500
125
100mS max.
---
Storage Temperature
-55
Measured at the location specified in the thermal
measurement figure. Maximum temperature varies
with model number, output current, and module
orientation – see curve in thermal performance
section of the data sheet.
Operating Temperature Range (Tc)
-40
125
˚C
Input Characteristics:
Unless otherwise specified, specifications apply over all Rated Input Voltage, Resistive Load, and Temperature conditions.
Characteristic
Operating Input Voltage
Maximum Input Current
Turn-on Voltage
Min
36
Typ
48
---
Max
75
4
Unit
Vdc
A
Notes & Conditions
---
Vin = 0 to Vin,max
---
33
30
3
---
Vdc
Vdc
Vdc
mS
Turn-off Voltage
26
---
Hysteresis
0.5
---
---
Startup Delay Time from application of input
voltage
35
---
Vo = 0 to 0.1*Vo,nom; on/off =on,
Io=Io,max, Tc=25˚C
Startup Delay Time from on/off
---
35
---
mS
Vo = 0 to 0.1*Vo,nom; Vin = Vi,nom,
Io=Io,max,Tc=25˚C
Output Voltage Rise Time
Inrush Transient
---
---
---
50
---
15
---
0.2
---
mS
A2s
Io=Io,max,Tc=25˚C, Vo=0.1 to 0.9*Vo,nom
Input Reflected Ripple
mApp
See input/output ripple and noise
measurements figure; BW = 20 MHz
Input Ripple Rejection
---
55
---
dB
@120Hz
Caution: The power modules are not internally fused. An external input line normal blow fuse with a
maximum value of 10A is required, see the Safety Considerations section of the data sheet.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
4/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48007A120V-000 through -015: 12V, 6.5A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
11.64
12
12.36
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
11.58
12
12.42
Vdc
Efficiency
---
---
---
---
90.5
10
---
24
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
10
24
60
240
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
0.5
---
6.5
A
Output Current Limiting Threshold
Short Circuit Current
---
---
8.5
12
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
80
26
200
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
60
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
220
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
---
400
---
5
---
%
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
kHz
V
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
13.6
0
15.7
2000&
---
---
uF
pF
MΩ
V
---
1000
---
10
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
5/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48007A120V-000 through -015: 12V, 6.5A Output
95
90
85
80
75
70
12
10
8
6
4
2
0
0
0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3
7
0
0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3
7
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48007A120V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48007A120V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
95
90
85
80
75
70
14
12
10
8
6
4
2
0
0
0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3
7
0
0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3
7
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48007A120V-000 Typical Efficiency vs. Input
Voltage at Ta=85 degrees.
iEA48007A120V-000 Typical Power Dissipation vs.
Input Voltage at Ta=85 degrees
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
6/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48007A120V-000 through -015: 12V, 6.5A Output
12.34
12.24
12.14
12.04
11.94
11.84
11.74
11.64
0
0.7 1.4 2.1 2.8 3.5 4.2 4.9 5.6 6.3
7
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48007A120V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48007A120V-001 Typical startup characteristic from
on/off at full load. Ch 1 - on/off signal, Ch 2 – output
voltage
iEA48007A120V-000 Typical Output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS.
iEA48007A120V-000 Typical Output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS and 2200uF external load.
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
937K
488K
-10%
+10%
e.g. trim up 5%
5.1 × 12⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48007A120V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
7/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48007A120V-000 through -015: 12V, 6.5A Output
12.5
12
11.5
11
10.5
10
0
2
4
6
8
10
12
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48007A120V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48007A120V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
3.5
3
14
12
10
8
2.5
2
1.5
1
6
4
0.5
2
0
0
27 32 37 41 46 51 56 61 65 70 75
27 32 37 41 46
51 56 61 65 70 75
Input Voltage (V)
Input Voltage (V)
Io_min = 0A
Io_mid = 3.3A
Io_max = 6.5A
Io_min = 0A
Io_mid = 3.3A
Io_max = 6.5A
iEA48007A120V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48007A120V-000 Typical Output Voltage vs. Input
Voltage Characteristics
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
8/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48007A120V-000 through -015: 12V, 6.5A Output
7
6
5
4
3
2
7
6
5
4
3
2
1
0
NC
0.5 m/s(100 LFM)
1.0m/s(200 LFM)
2.0 m/s(400LFM)
3.0 m/s(600LFM)
Tc, Thermal Limit
NC
0.5 m/s (100 LFM)
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
3.0 m/s (600 LFM)
Tc, Thermal Limit
1
0
25
45
65
85
105
125
25
45
65
85
105
125
Temperat ure ( oC)
Temperature (oC)
iEA48007A120V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
iEA48007A120V-000 maximum output current vs.ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 1 to pin 3.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48007A120V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
9/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48015A050V-000 through -015: 5V, 15A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
4.92
5
5.08
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
4.85
5
5.15
Vdc
Efficiency
---
---
---
---
90
2
---
10
10
75
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
1
30
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
1
---
15
A
Output Current Limiting Threshold
Short Circuit Current
---
---
20
14
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
55
7
125
---
Measured across one 0.1 uF ceramic
capacitor and a 22uF ceramic capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
100
200
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
5.7
0
---
400
---
250
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
6.7
---
5000&
---
uF
pF
MΩ
V
---
10
1000
---
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
10/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48015A050V-000 through -015: 5V, 15A Output
95
90
85
80
75
70
12
10
8
6
4
2
0
1
2.4 3.8 5.2 6.6
8
9.4 10.8 12.2 13.6 15
1
2.4 3.8 5.2 6.6
8
9.4 10.8 12.2 13.6 15
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48015A050V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48015A050V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
95
90
85
80
75
70
12
10
8
6
4
2
0
1
2.4 3.8 5.2 6.6
8
9.4 10.8 12.2 13.6 15
1
2.4 3.8 5.2 6.6
8
9.4 10.8 12.2 13.6 15
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48015A050V-000 Typical Efficiency vs. Input
Voltage at Ta=85 degrees.
iEA48015A050V-000 Typical Power Dissipation vs.
Input Voltage at Ta=85 degrees
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
11/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48015A050V-000 through -015: 5V, 15A Output
5.05
5.04
5.03
5.02
5.01
5
4.99
4.98
4.97
4.96
4.95
1
2.4 3.8 5.2 6.6
8
9.4 10.8 12.2 13.6 15
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48015A050V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48015A050V-001 Typical startup characteristic from
on/off at full load. Ch4 - on/off signal, Ch 1 – output
voltage
iEA48015A050V-000 Typical Output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS.
iEA48015A050V-000 Typical Output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS and 5000uF load.
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
325K
168K
-10%
+10%
e.g. trim up 5%
5.1 × 5⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48015A050V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
12/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48015A050V-000 through -015: 5V, 15A Output
5.01
4.99
4.97
4.95
4.93
4.91
4.89
4.87
4.85
1
6
11
16
21
26
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48015A050V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48015A050V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
3
2.5
2
6
5
4
3
2
1
0
1.5
1
0.5
0
27 32 37 41 46 51 56 61 65 70 75
27
32
37
41
46
51
56
61
65
70
75
Input Voltage (V)
Input Voltage (V)
Io_min = 0.8A
Io_mid = 7.5A
Io_max = 15.1A
Io_min = 0.8A
Io_mid = 7.5A
Io_max = 15.1A
iEA48015A050V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48015A050V-000 Typical Output Voltage vs. Input
Voltage Characteristics
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
13/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48015A050V-000 through -015: 5V, 15A Output
16
14
12
10
NC
8
0.5 m/s (100 LFM)
6
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
4
3.0 m/s (600 LFM)
2
Tc, Thermal Limit
0
25
45
65
85
105
125
Temperature (oC)
iEA48015A050V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48015A050V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
14/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48020A033V-000 through -015: 3.3V, 20A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
3.25
3.3
3.35
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
3.20
3.3
3.40
Vdc
Efficiency
---
---
---
---
89.5
2
---
7
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
3
8
15
60
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
1.5
---
20
A
Output Current Limiting Threshold
Short Circuit Current
---
---
29
20
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
35
11
100
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
The trim range is reduced to 105% when
the input voltage is below 40V.
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
The sense range is reduced to 5% when the
input voltage is below 40V.
Dynamic Response:
Recovery Time
---
---
90
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
180
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
---
400
---
165
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
3.75
100
---
4.4
---
5000&
---
uF
pF
MΩ
V
Recommend TDK part C3225X5R0J107MT
Required for trim calculation
1000
---
10
---
Vref
1.225
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
15/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48020A033V-000 through -015: 3.3V, 20A Output
95
90
85
80
75
70
12
10
8
6
4
2
0
1
2.9 4.8 6.7 8.6 10.5 12.4 14.3 16.2 18.1 20
1
2.9 4.8 6.7 8.6 10.5 12.4 14.3 16.2 18.1 20
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48020A033V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48020A033V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
95
90
85
80
75
70
12
10
8
6
4
2
0
1
2.9 4.8 6.7 8.6 10.5 12.4 14.3 16.2 18.1 20
1
2.9 4.8 6.7 8.6 10.5 12.4 14.3 16.2 18.1 20
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48020A033V-000 Typical Efficiency vs. Input
Voltage at Ta=85 degrees.
iEA48020A033V-000 Typical Power Dissipation vs.
Input Voltage at Ta=85 degrees
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
16/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48020A033V-000 through -015: 3.3V, 20A Output
3.35
3.33
3.31
3.29
3.27
3.25
1
2.9 4.8 6.7 8.6 10.5 12.4 14.3 16.2 18.1 20
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48020A033V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48020A033V-001 Typical startup characteristic from
on/off at full load. Ch2 - on/off signal, Ch 1 – output
voltage
iEA48020A033V-000 Typical output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS.
iEA48020A033V-000 Typical output voltage response
to load step from 50% to 75% of full load with output
current slew rate of 0.1A/uS and 5000uF load.
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
176.3K
89.9K
-10%
+10%
e.g. trim up 5%
5.1 × 3.3⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48020A033V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
17/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48020A033V-000 through -015: 3.3V, 20A Output
3.32
3.31
3.3
3.29
3.28
3.27
3.26
3.25
20
22
24
26
28
30
32
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48020A033V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48020A033V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
3
2.5
2
3.5
3
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
27 32 37 41 46 51 56 61 65 70 75
27 32 37 41 46 51 56 61 65 70 75
Input Voltage (V)
Input Voltage (V)
Io_min = 1A
Io_mid = 10A
Io_max = 20A
Io_min = 1A
Io_mid = 10A
Io_max = 20A
iEA48020A033V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48020A033V-000 Typical Output Voltage vs. Input
Voltage Characteristics
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
18/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48020A033V-000 through -015: 3.3V, 20A Output
25
20
15
10
5
25
20
15
10
5
NC
NC
0.5 m/s (100 LFM)
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
3.0 m/s (600 LFM)
Tc, Thermal Limit
0.5 m/s (100 LFM)
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
3.0 m/s (600 LFM)
Tc, Thermal Limit
30
40
50
60
70
80
90
100 110 120 130
30
40
50
60
70
80
90 100 110 120 130
Temperature (C)
Temperature (C)
iEA48020A033V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
iEA48020A033V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 1 to pin 3.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48020A033V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
19/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48025A025V-000 through -015: 2.5V, 25A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
2.46
2.5
2.54
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
2.42
2.5
2.58
Vdc
Efficiency
---
---
---
---
85.5
1
---
5
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
1
7
10
50
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
2.0
---
25
A
Output Current Limiting Threshold
Short Circuit Current
---
---
31
20
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
35
11
100
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
100*
200*
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
2.7
0
---
400
---
165
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
3.5
---
5000&
---
uF
pF
MΩ
V
---
10
1000
---
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
20/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48025A025V-000 through -015: 2.5V, 25A Output
95
90
85
80
75
70
14
12
10
8
6
4
2
0
0
2.51 5.02 7.53 10 12.6 15.1 17.6 20.1 22.6 25.1
0
2.51 5.02 7.53 10 12.6 15.1 17.6 20.1 22.6 25.1
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A025V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48025A025V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
2.54
2.53
2.52
2.51
2.5
2.49
2.48
2.47
2.46
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A025V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48025A025V-001 Typical startup characteristic from
on/off at full load. Ch3 - on/off signal, Ch 1 – output
voltage
2.55
2.5
2.45
2.4
2.35
2.3
15
20
25
30
35
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A025V-000 Typical startup characteristic
from input voltage application at full load. Ch3 - input
voltage, Ch 1 – output voltage
iEA48025A025V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
21/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48025A025V-000 through -015: 2.5V, 25A Output
3
2.5
2
3
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
27 32
37 41
46 51 56
61 65
70 75
27 31.8 36.6 41.4 46.2 51 55.8 60.6 65.4 70.2 75
Input Voltage (V)
Input Voltage (V)
Io_min = 0A
Io_mid = 12.6A
Io_min = 0A
Io_mid = 12.6A
Io_max = 25.2A
Io_max = 25.2A
iEA48025A025V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48025A025V-000 Typical Output Voltage vs. Input
Voltage Characteristics
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
106K
-10%
+10%
53.3K
e.g. trim up 5%
5.1× 2.5⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48025A025V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
22/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48025A025V-000 through -015: 2.5V, 25A Output
30
25
20
15
10
5
0
25
45
65
85
105
125
Temperature (oC)
NC
0.5 m/s (100 LFM)
2.0 m/s (400 LFM)
Tc, Thermal Limit
1.0 m/s (200 LFM)
3.0 m/s (600 LFM)
iEA48025A025V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48025A025V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
23/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48025A018V-000 through -015: 1.8V, 25A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
1.77
1.8
1.83
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
1.74
1.8
1.86
Vdc
Efficiency
---
---
---
---
82.5
1
---
5
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
1
7
10
50
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
2.0
---
25
A
Output Current Limiting Threshold
Short Circuit Current
---
---
35
20
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
35
8
100
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
120
130
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
---
400
---
165
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
2.12
0
2.58
5000&
---
---
uF
pF
MΩ
V
---
1000
---
10
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
24/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48025A018V-000 through -015: 1.8V, 25A Output
90
88
86
84
82
80
78
76
74
72
70
12
10
8
6
4
2
0
2
4.3 6.6 8.9 11.2 13.5 15.8 18.1 20.4 22.7 25
2
4.3 6.6 8.9 11.2 13.5 15.8 18.1 20.4 22.7 25
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A018V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48025A018V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
1.83
1.82
1.81
1.8
1.79
1.78
1.77
2
4
7
9
11 14 16 18 20 23 25
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A018V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48025A018V-001 Typical startup characteristic from
on/off at full load. Ch1 - on/off signal, Ch 4 – output
voltage
iEA48025A018V-000 Typical startup characteristic
from input voltage application at full load. Ch1 - input
voltage, Ch 4 – output voltage
iEA48025A018V-000 Typical transient response.
Output voltage response to load step from 50% to 75%
of full load with output current slew rate of 0.1A/uS.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
25/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48025A018V-000 through -015: 1.8V, 25A Output
1.85
1.8
1.75
1.7
1.65
1.6
1.55
1.5
20
25
30
35
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A018V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48025A018V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
2.5
2
2
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
1.5
1
0.5
0
26
31
36
41
46
51 55
60
65
70
75
26
31
36
41
46
51 55
60
65
70
75
Input Voltage (V)
Input Voltage (V)
Io_min = 1.8A
Io_mid = 12.6A
Io_min = 1.8A
Io_max = 25.2A
Io_mid = 12.6A
Io_max = 25.2A
iEA48025A018V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48025A018V-000 Typical Output Voltage vs. Input
Voltage Characteristics
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
45.2K
21.2K
-10%
+10%
e.g. trim up 5%
5.1 × 1.8⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48025A018V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
26/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48025A018V-000 through -015: 1.8V, 25A Output
30
25
20
NC
15
10
5
0.5 m/s (100 LFM)
1.0 m/s (200 LFM)
1.5 m/s (300 LFM)
2.0 m/s (400 LFM)
3.0 m/s (600 LFM)
Tc, Thermal Limit
0
10
30
50
70
90
110
130
Temperature (oC)
iEA48025A018V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48025A018V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
27/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48025A015V-000 through -015: 1.5V, 25A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
1.47
1.5
1.53
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
1.45
1.5
1.55
Vdc
Efficiency
---
---
---
---
81
1
---
5
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
1
7
10
50
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
2.0
---
25
A
Output Current Limiting Threshold
Short Circuit Current
---
---
35
20
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
30
8
100
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
120
85
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
1.7
0
---
400
---
140
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
2.3
---
5000&
---
uF
pF
MΩ
V
---
10
1000
---
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
28/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48025A015V-000 through -015: 1.5V, 25A Output
88
86
84
82
80
78
76
74
72
70
12
10
8
6
4
2
0
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A015V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48025A015V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
1.53
1.52
1.51
1.5
1.49
1.48
1.47
0
2.5
5
7.5 10 12.5 15 17.5 20 22.5 25
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A015V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48025A015V-001 Typical startup characteristic from
on/off at full load. Ch3 - on/off signal, Ch 1 – output
voltage
iEA48025A015V-000 Typical startup characteristic
from input voltage application at full load. Ch3 - input
voltage, Ch 1 – output voltage
iEA48025A015V-000 Typical transient response.
Output voltage response to load step from 50% to 75%
of full load with output current slew rate of 0.1A/uS.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
29/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48025A015V-000 through -015: 1.5V, 25A Output
1.52
1.5
1.48
1.46
1.44
1.42
1.4
25
27
29
31
33
35
37
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A015V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48025A015V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
1.8
1.6
1.4
1.2
1
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0.8
0.6
0.4
0.2
0
27.0
31.8
36.6
41.4
46.2
51.0
55.8
27 32 37 41 46 51 56 61 65 70 75
Input Voltage (V)
Input Voltage (V)
Io_min = 0A
Io_mid = 12.6A
Io_max = 25.2A
Io_min = 0A
Io_mid = 12.6A
Io_max = 25.2A
iEA48025A015V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48025A015V-000 Typical Output Voltage vs. Input
Voltage Characteristics
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
91.8K
40.8K
+5%
18.9K
7.5K
-10%
+10%
e.g. trim up 5%
5.1 × 1.5⋅(100 + 5)
510
Rup :=
−
− 10.2 ⋅K
1.225× 5
5
iEA48025A015V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
30/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48025A015V-000 through -015: 1.5V, 25A Output
30
25
20
15
NC
0.5 m/s (100 LFM)
10
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
5
3.0 m/s (600 LFM)
Tc, Thermal Limit
0
25
45
65
85
105
125
145
Temperature (oC)
iEA48025A015V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48025A015V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
31/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Data:
iEA48025A012V-000 through -015: 1.2V, 25A Output
Characteristic
Min
Typ
Max
Unit
Notes & Conditions
Output Voltage Initial Setpoint
1.182
1.2
1.218
Vdc
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Over all rated input voltage, load, and
temperature conditions to end of life
Output Voltage Tolerance
1.164
1.2
1.236
Vdc
Efficiency
---
---
---
---
78
1
---
5
%
Vin=Vin,nom; Io=Io,max; Tc = 25˚C
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Line Regulation
Load Regulation
Temperature Regulation
mV
mV
mV
1
7
10
50
Tc=Tc,min to Tc,max
At loads less than Io,min the module will
continue to regulate the output voltage, but
the output ripple may increase
Output Current
2.5
---
25
A
Output Current Limiting Threshold
Short Circuit Current
---
---
33
20
---
---
A
A
Vo = 0.9*Vo,nom, Tc<Tc,max
Vo = 0.25V, Tc = 25˚C
mVpp
---
---
45
10
100
---
Measured across one 1.0 uF ceramic
capacitor and a 10uF tantalum capacitor –
see input/output ripple measurement figure;
BW = 20MHz
Output Ripple and Noise Voltage
mVrms
Output Voltage Adjustment Range
Output Voltage Sense Range
90
---
---
---
110
10
%Vo,nom
%Vo,nom
Dynamic Response:
Recovery Time
---
---
175
100
---
---
di/dt = 0.1A/uS, Vin=Vin,nom; load step
from 50% to 75% of Io,max
uS
Transient Voltage
mV
Output Voltage Overshoot during startup
Switching Frequency
---
---
1.5
0
---
300
---
125
---
mV
kHz
V
Vin=Vin,nom; Io=Io,max,Tc=25˚C
Fixed
Output Over Voltage Protection
External Load Capacitance
Isolation Capacitance
Isolation Resistance
2.0
---
5000&
---
uF
pF
MΩ
V
---
10
1000
---
---
Vref
1.225
Required for trim calculation
& Contact TDK Innoveta for applications that require additional capacitance or very low esr
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
32/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics:
iEA48025A012V-000 through -015: 1.2V, 25A Output
86
84
82
80
78
76
74
72
70
12
10
8
6
4
2
0
1
3.4 5.8 8.2 10.6 13 15.4 17.8 20.2 22.6 25
1
3.4 5.8 8.2 10.6 13 15.4 17.8 20.2 22.6 25
Output Current (A)
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A012V-000 Typical Efficiency vs. Input
Voltage at Ta=25 degrees.
iEA48025A012V-000 Typical Power Dissipation vs.
Input Voltage at Ta=25 degrees
1.22
1.215
1.21
1.205
1.2
1.195
1.19
1.185
1.18
1
3.4 5.8 8.2 10.6 13 15.4 17.8 20.2 22.6 25
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A012V-000 Typical Output Voltage vs. Load
Current at Ta = 25 degrees
iEA48025A012V-001 Typical startup characteristic from
on/off at full load.Ch1-on/off signal, Ch3 –output voltage
iEA48025A012V-000 Typical startup characteristic
from input voltage application at full load. Ch1 - input
voltage, Ch3 – output voltage
iEA48025A012V-000 Typical transient response.
Output voltage response to load step from 50% to 75%
of full load with output current slew rate of 0.1A/uS.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
33/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Electrical Characteristics (continued):
iEA48025A012V-000 through -015: 1.2V, 25A Output
1.25
1.2
1.15
1.1
1.05
1
20
25
30
35
Output Current (A)
Vin = 36V
Vin = 48V
Vin = 75V
iEA48025A012V-000 Typical Output Current Limit
Characteristics vs. Input Voltage at Ta=25 degrees.
iEA48025A012V-000 Typical Output Ripple at nominal
input voltage and full load at Ta=25 degrees
1.6
1.4
1.2
1
1.4
1.2
1
0.8
0.6
0.4
0.2
0.8
0.6
0.4
0.2
0
0
27 32 37 41 46 51 56 61 65 70 75
27 32 37 41 46 51 56 61 65 70 75
Input Voltage (V)
Input Voltage (V)
Io_min = 1.3A
Io_mid = 12.6A
Io_max = 25.2A
Io_min = 1.3A
Io_mid = 12.6A
Io_max = 25.2A
iEA48025A012V-000 Typical Input Current vs. Input
Voltage Characteristics
iEA48025A012V-000 Typical Output Voltage vs. Input
Voltage Characteristics
Trim
Down
Resistor
(Kohm)
%
Change
of Vout
%
Change
of Vout
Trim Up
Resistor
(Kohm)
-5%
18K
8K
+5%
20K
10K
-10%
+10%
e.g. trim up 5%
100
Rup :=
⋅K
5
iEA48025A012V-000 Calculated resistor values for
output voltage adjustment
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
34/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Performance:
iEA48025A012V-000 through -015: 1.2V, 25A Output
30
25
20
15
NC
0.5 m/s (100 LFM)
10
1.0 m/s (200 LFM)
2.0 m/s (400 LFM)
5
3.0 m/s (600 LFM)
Tc, Thermal Limit
0
25
45
65
85
105
125
145
Temperature (oC)
iEA48025A012V-000 maximum output current vs. ambient
temperature at nominal input voltage for airflow rates natural
convection (60lfm) to 600lfm with airflow from pin 3 to pin 1.
Best orientation
airflow
Thermal measurement
location on PWB Cu
iEA48025A012V-000 thermal measurement location –
top view
Both the thermal curves provided and the example given above are based upon measurements made in TDK Innoveta’s
experimental test setup that is described in the Thermal Management section. Due to the large number of variables in
system design, TDK Innoveta recommends that the user verify the module’s thermal performance in the end application.
The critical component should be thermo coupled and monitored, and should not exceed the temperature limit specified in
the derating curve above. It is critical that the thermocouple be mounted in a manner that gives direct thermal contact or
significant measurement errors may result. TDK Innoveta can provide modules with a thermocouple pre-mounted to the
critical component for system verification tests.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
35/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Thermal Management:
to the airflow direction can have a significant
impact on the module’s thermal
performance.
An important part of the overall system
design process is thermal management;
thermal design must be considered at all
levels to ensure good reliability and lifetime
of the final system. Superior thermal design
and the ability to operate in severe
Thermal Derating: For proper application of
the power module in a given thermal
environment, output current derating curves
are provided as a design
application environments are key elements
of a robust, reliable power module.
Adjacent PCB
A finite amount of heat must be dissipated
from the power module to the surrounding
environment. This heat is transferred by the
three modes of heat transfer: convection,
conduction and radiation. While all three
modes of heat transfer are present in every
application, convection is the dominant
mode of heat transfer in most applications.
However, to ensure adequate cooling and
proper operation, all three modes should be
considered in a final system configuration.
Module
Centerline
A
I
R
F
L
O
W
12.7
(0.50)
76 (3.0)
The open frame design of the power module
provides an air path to individual
AIRFLOW
components. This air path improves
convection cooling to the surrounding
environment, which reduces areas of heat
concentration and resulting hot spots.
Air Velocity and Ambient
Temperature
Measurement Location
Air Passage
Centerline
Test Setup: The thermal performance data
of the power module is based upon
Wind Tunnel Test Setup Figure Dimensions are
in millimeters and (inches).
measurements obtained from a wind tunnel
test with the setup shown in the wind tunnel
figure. This thermal test setup replicates the
typical thermal environments encountered in
most modern electronic systems with
distributed power architectures. The
electronic equipment in networking, telecom,
wireless, and advanced computer systems
operates in similar environments and utilizes
vertically mounted PCBs or circuit cards in
cabinet racks.
guideline on the Thermal Performance
section for the power module of interest.
The module temperature should be
measured in the final system configuration
to ensure proper thermal management of
the power module. For thermal performance
verification, the module temperature should
be measured at the component indicated in
the thermal measurement location figure on
the thermal performance page for the power
module of interest. In all conditions, the
power module should be operated below the
maximum operating temperature shown on
the derating curve. For improved design
margins and enhanced system reliability, the
power module may be operated at
The power module, as shown in the figure,
is mounted on a printed circuit board (PCB)
and is vertically oriented within the wind
tunnel. The cross section of the airflow
passage is rectangular. The spacing
between the top of the module and a parallel
facing PCB is kept at a constant (0.5 in).
The power module’s orientation with respect
temperatures below the maximum rated
operating temperature.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
36/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Heat transfer by convection can be
An optional latching over-voltage protection
enhanced by increasing the airflow rate that
the power module experiences. The
maximum output current of the power
module is a function of ambient temperature
(TAMB) and airflow rate as shown in the
thermal performance figures on the thermal
performance page for the power module of
interest. The curves in the figures are
shown for natural convection through 2 m/s
(400 ft/min). The data for the natural
convection condition has been collected at
0.3 m/s (60 ft/min) of airflow, which is the
typical airflow generated by other heat
dissipating components in many of the
systems that these types of modules are
used in. In the final system configurations,
the airflow rate for the natural convection
condition can vary due to temperature
gradients from other heat dissipating
components.
is available. On modules with this feature,
the power module will shut down once it
detects that the output voltage has reached
the level indicated on the Electrical Data
section for the power module of interest.
The module remains off unless the input
voltage is recycled.
Thermal Protection: When the power
modules exceed the maximum operating
temperature, the modules may turn off to
safeguard the power unit against thermal
damage. The module will auto restart as the
unit is cooled below the over temperature
threshold. On modules with the latching
over-voltage protection feature, the unit may
latch off during a severe over temperature
condition; the module remains off unless the
input voltage is recycled.
Remote On/Off: - The power modules have
an internal remote on/off circuit. The user
must supply an open-collector or compatible
switch between the Vin(-) pin and the on/off
pin. The maximum voltage generated by
the power module at the on/off terminal is
15V. The maximum allowable leakage
current of the switch is 50uA. The switch
must be capable of maintaining a low signal
Von/off < 1.2V while sinking 1mA.
Operating Information:
Over-Current Protection: The power
modules have current limit protection to
protect the module during output overload
and short circuit conditions. During overload
conditions, the power modules may protect
themselves by entering a hiccup current limit
mode. The modules will operate normally
once the output current returns to the
specified operating range. There is a typical
delay of 30mS from the time an overload
condition appears at the module output until
the hiccup mode will occur.
The standard on/off logic is positive logic.
The power module will turn on if terminal 2 is
left open and will be off if terminal 2 is
connected to terminal 3. If the positive logic
circuit is not being used, terminal 2 should
be left open.
Output Over-Voltage Protection: The
power modules have a control circuit,
independent of the primary control loop that
reduces the risk of over voltage appearing at
the output of the power module during a
fault condition. If there is a fault in the
primary regulation loop, the over voltage
protection circuitry will cause the power
module to enter a hiccup over-voltage mode
once it detects that the output voltage has
reached the level indicated on the Electrical
Data section for the power module of
interest. When the condition causing the
over-voltage is corrected, the module will
operate normally.
An optional negative logic is available. The
power module will turn on if terminal 2 is
connected to terminal 3, and it will be off if
terminal 2 is left open. If the negative logic
feature is not being used, terminal 2 should
be shorted to terminal 3.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
37/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
For 1.2V output only:
Vin (+)
On/ Off
100
Rdown :=
− 2 ⋅1000
%Vo
The current limit set point does not increase
as the module is trimmed down, so the
available output power is reduced.
Vin(-)
Vout(+)
On/Off Circuit for positive or negative
logic
Sense(+)
Rup
Output Voltage Adjustment: The output
voltage of the power module may be
adjusted by using an external resistor
connected between the Vout trim terminal
(pin 6) and either the Sense (+) or Sense (-)
terminal. If the output voltage adjustment
feature is not used, pin 6 should be left
open. Care should be taken to avoid
injecting noise into the power module’s trim
pin. A small 0.01uF capacitor between the
power module’s trim pin and Sense (-) pin
may help avoid this.
Trim
Sense(-)
Vout(-)
Circuit to increase output voltage
With a resistor between the trim and sense
(+) terminals, the output voltage is adjusted
up. To adjust the output voltage up a
percentage of Vout (%Vo) from Vo,nom the
trim resistor should be chosen according to
the following equation:
Vout(+)
Sense(+)
For all outputs except 1.2V:
Trim
Rdown
5.1Vonom⋅(100 + %Vo)
510
Rup :=
−
− 10.2 ⋅1000
Sense(-)
Vout(-)
Vref⋅%Vo
%Vo
For 1.2V output only:
Circuit to decrease output voltage
100
Rup :=
⋅1000
%Vo
With a resistor between the trim and Sense
(-) terminals, the output voltage is adjusted
down. To adjust the output voltage down a
percentage of Vout (%Vo) from Vo,nom, the
trim resistor should be chosen according to
the following equation:
The value of Vref is found in the Electrical
Data section for the power module of
interest. The maximum power available
from the power module is fixed. As the
output voltage is trimmed up, the maximum
output current must be decreased to
maintain the maximum rated power of the
module. As the output voltage is trimmed,
the output over-voltage set point is not
adjusted. Trimming the output voltage too
high may cause the output over voltage
protection circuit to be triggered.
For all outputs except 1.2V:
510
Rdown :=
− 10.2 ⋅1000
%Vo
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
38/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Remote Sense: The power modules feature
remote sense to compensate for the effect
of output distribution drops. The output
voltage sense range defines the maximum
voltage allowed between the output power
terminals and output sense terminals, and it
is found on the electrical data page for the
power module of interest. If the remote
sense feature is not being used, the
Sense(+) terminal should be connected to
the Vo(+) terminal and the Sense (-)
terminal should be connected to the Vo(-)
terminal.
Input Impedance:
The source impedance of the power feeding
the DC/DC converter module will interact
with the DC/DC converter. To minimize the
interaction, a 10-100uF input electrolytic
capacitor should be present if the source
inductance is greater than 1.5uH.
Reliability:
The power modules are designed using TDK
Innoveta’s stringent design guidelines for
component derating, product qualification,
and design reviews. Early failures are
screened out by both burn-in and an
automated final test. The MTBF is
calculated to be greater than 4.8M hours at
full output power and Ta = 40˚C using the
Telcordia SR-332 calculation method.
The output voltage at the Vo(+) and Vo(-)
terminals can be increased by either the
remote sense or the output voltage
adjustment feature. The maximum voltage
increase allowed is the larger of the remote
sense range or the output voltage
adjustment range; it is not the sum of both.
Improper handling or cleaning processes
can adversely affect the appearance,
testability, and reliability of the power
modules. Contact TDK Innoveta technical
support for guidance regarding proper
handling, cleaning, and soldering of TDK
Innoveta’s power modules.
As the output voltage increases due to the
use of the remote sense, the maximum
output current must be decreased for the
power module to remain below its maximum
power rating.
EMC Considerations: TDK Innoveta power
modules are designed for use in a wide
variety of systems and applications. For
assistance with designing for EMC
compliance, please contact TDK Innoveta
technical support.
Quality:
TDK Innoveta’s product development
process incorporates advanced quality
planning tools such as FMEA and Cpk
analysis to ensure designs are robust and
reliable. All products are assembled at ISO
certified assembly plants.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
39/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
Input/Output Ripple and Noise Measurements:
12uH
1
2
Battery
+
+
Voutput
-
RLoad
Cext
Vinput
-
33uF
220uF
esr<0.1
100KHz
esr<0.7
100KHz
Ground Plane
The input reflected ripple is measured with a current probe and oscilloscope. The ripple
current is the current through the 12uH inductor.
The output ripple measurement is made approximately 9 cm (3.5 in.) from the power module
using an oscilloscope and BNC socket. The capacitor Cext is located about 5 cm (2 in.) from
the power module; its value varies from code to code and is found on the electrical data page
for the power module of interest under the ripple & noise voltage specification in the Notes &
Conditions column.
Safety Considerations:
When the supply to the DC-DC converter is
For safety agency approval of the system in
which the DC-DC power module is installed,
the power module must be installed in
compliance with the creepage and clearance
requirements of the safety agency. The
isolation is basic insulation. For
less than 60Vdc, the power module meets
all of the requirements for SELV. If the
input voltage is a hazardous voltage that
exceeds 60Vdc, the output can be
considered SELV only if the following
conditions are met:
applications requiring basic insulation, care
must be taken to maintain minimum
creepage and clearance distances when
routing traces near the power module.
1) The input source is isolated from the
ac mains by reinforced insulation.
2) The input terminal pins are not
accessible.
3) One pole of the input and one pole
of the output are grounded or both
are kept floating.
4) Single fault testing is performed on
the end system to ensure that under
a single fault, hazardous voltages
do not appear at the module output.
As part of the production process, the power
modules are hi-pot tested from primary and
secondary at a test voltage of 1500Vdc.
To preserve maximum flexibility, the power
modules are not internally fused. An
external input line normal blow fuse with a
maximum value of 10A is required by safety
agencies. A lower value fuse can be
selected based upon the maximum dc input
current and maximum inrush energy of the
power module.
Warranty:
TDK Innoveta’s comprehensive line of
power solutions includes efficient, high-
density DC-DC converters. TDK Innoveta
offers a three-year limited warranty.
Complete warranty information is listed on
our web site or is available upon request
from TDK Innoveta.
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
40/41
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Data Sheet: Belleta iEA Series –Single Output Eighth Brick
3320 Matrix Drive, Suite 100
Richardson, TX 75082
Phone (877) 498-0099 Toll Free
(469) 916.4747
Information furnished by TDK Innoveta is believed to be accurate and reliable. However, TDK Innoveta assumes no responsibility
for its use, nor for any infringement of patents or other rights of third parties, which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of TDK Innoveta. TDK Innoveta components are not designed to be
used in applications, such as life support systems, wherein failure or malfunction could result in injury or death. All sales are
subject to TDK Innoveta’s Terms and Conditions of Sale, which are available upon request. Specifications are subject to change
Fax
(877) 498-0143 Toll Free
(214) 239.3101
℡
(877) 498-0099
©2004 TDK Innoveta® Inc.
iEAFullDatasheet 032707 3/29/2007 Revision 2.0
41/41
Download from Www.Somanuals.com. All Manuals Search And Download.
|