USER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with an arrowhead
symbol within an equilateral triangle, is
intended to alert the user to the
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying the
product.
presence of uninsulated "dangerous volt-
age" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
Warning!
•
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture
and objects filled with liquids, such as vases,
should not be placed on this apparatus.
This apparatus must be earthed.
Use a three wire grounding type line cord
like the one supplied with the product.
Be advised that different operating voltages
require the use of differ ent types of line
cord and attachment plugs.
•
•
manufacturer's instructions.
•
•
8
9
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety. If
the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
Check the voltage in your area and use the
correct type. See table below:
Voltage
Line plug according to standard
110-125V UL817 and CSA C22.2 no 42.
220-230V CEE 7 page VII, SR section
107-2-D1/IEC 83 page C4.
240V
BS 1363 of 1984. Specification for
13A fused plugs and switched and
unswitched socket outlets.
10 Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified
by the manufacturer.
•
•
•
This equipment should be installed near the
socket outlet and disconnection of the device
should be easily accessible.
To completely disconnect from AC mains,
disconnect the power supply cord from the AC
receptacle.
12
Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
The mains plug of the power supply shall
remain readily operable.
•
•
Do not install in a confined space.
Do not open the unit - risk of electric shock
inside.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Caution:
14 Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
You are cautioned that any change or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
Service
•
•
There are no user-serviceable parts inside.
All service must be performed by qualified
personnel.
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment has been type tested and found to comply with the limits for a class B digital device
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communication. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause interference to radio or
television equipment reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by any combination of the following measures:
TABLE OF CONTENTS
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTACT DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WELCOME
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Relocate or reorient the receiving antenna
• Increase the separation between the equipment and the receiver
• Plug the equipment into an outlet on a circuit different from that to which the receiver is connect-
ed
POWERCORE SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MAC OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
POWERCORE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE COMPACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE PCI MKII & UNPLUGGED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE EXPRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE FIREWIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE X8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWERCORE 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
If necessary, you can consult a dealer or experienced radio/television technician for additional assis-
tance.
PLEASE NOTE: Only equipment certified to comply with Class B (computer input/output devices,
terminals, printers, etc.) should be attached to this equipment, and it must have shielded interface
cables in order to comply with the Class B FCC limits on RF emissions.
INSTALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SOFTWARE INSTALLATION GUIDE PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SOFTWARE INSTALLATION GUIDE OSX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CANADIAN CUSTOMERS
This Class B digital apparatus complies with *Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada
POWERCORE HARDWARE INSTALLATION GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PCI MKII, EXPRESS & UNPLUGGED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FIREWIRE, X8, 6000 & COMPACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CERTIFICATE OF CONFORMITY
TC Electronic, Sindalsvej 34, 8240 Risskov, Denmark, hereby declares by own
responsibility that the following products:
THE POWERCORE CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ACCESSING THE CONTROL PANEL IN WINDOWS . . . . . . . . . . . . . . . . . . . . . . . 17
ACCESSING THE CONTROL PANEL IN MAC OS . . . . . . . . . . . . . . . . . . . . . . . . . 17
STATUS PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
POWERCORE TYPE ICON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DSP & MEMORY CONSUMPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EXPANDED STATUS PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUTHENTICATION ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NICKNAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PLUG-INS PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FREE TRIAL PERIOD ON OPTIONAL PLUG-INS . . . . . . . . . . . . . . . . . . . . . 19
PLUG-INS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PLUG-IN TYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
STATUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ACTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SETUP PAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CHECK FOR UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SYSTEM REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SYSTEM SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
POWERCORE FIREWIRE
POWERCORE COMPACT
POWERCORE PCI MKII
POWERCORE EXPRESS
POWERCORE UNPLUGGED
POWERCORE X8
POWERCORE 6000
- marked with CE-label are covered by this certificate and conform with the
following standards :
EN 60950 Safety for information technology equipment, including electrical
business (IEC 60950) equipment.
EN 55022 Limits and methods of measurement of radio disturbance
characteristics (CISPR 22) of information technology equipment.
EN 55024 Information technology equipment – Immunity characteristics –
(CISPR 24) Limits and methods of measurement.
With reference to regulations in following directives : 73/23/EEC, 89/336/EEC
Issued in Risskov, September 06
Mads Peter Lübeck
Chief Executive Officer
POWERCORE / 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING THE MOST FROM POWERCORE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
BUFFER SIZES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
THE DISABLED STATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
96 kHz PROCESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
• Where can I download the latest drivers. . . . . . . . . . . . . . . . . . . . . . . . . . 36
• I can run half the number of effects at 96 kHz than I can at 48 kHz .. . . . 36
• PowerCore plug-ins don’t show in my applications plug-in selection dialog . 36
• I don’t see all PowerCore plug-ins in my native mixer’s inserts,
LATENCY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
sends or master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
• Every-time I load a plug-in in LOGIC or DIGITAL PERFORMER,
my application Quits .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
• The input of my PowerCore plug-in is clipping
WHAT IS LATENCY? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
NO LATENCY MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
LATENCY IN THE MASTER FADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
(and/or I hear distorted audio) .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
• My source audio is mono after inserting a PowerCore plug-in . . . . . . . . . . 37
• The plug-in doesn’t open or there is no audio when I activate the plug-in. . 37
• The audio is corrupted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
USING POWERCORE PLUG-INS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PLUG-INS INCLUDED WITH
POWERCORE COMPACT, FIREWIRE, PCI MKII, X8 and 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
24/7·C LIMITING AMPLIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
NOVELTECH CHARACTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CHORUS-DELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CLASSIC VERB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
EQSAT CUSTOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
FILTROID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MASTER X3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MEGAREVERB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
POWERCORE 01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
POWERCORE CL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
VOICESTRIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TUBIFEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DENOISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DYNAMIC EQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FURTHER SUPPORT RESOURCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TC ELECTRONIC KNOWLEDGE BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CONTACTING THE TC ELECTRONIC SUPPORT TEAM . . . . . . . . . . . . . . . . . . . . . 38
CONTACT DETAILS
TC ELECTRONIC A/S
Customer Support
Sindalsvej 34
ADDITIONAL PLUG-INS INCLUDED WITH POWERCORE 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
VSS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
MD3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
BRICKWALL LIMITER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
NONLIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DVR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
UNWRAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TAP FACTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Risskov DK-8240
Denmark
USA:
TC Electronic Inc.
POWERCORE IN MACOS X. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
OS X DOMAINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PLUG-IN LOCATIONS (LOCAL DOMAIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CONTROL PANEL LOCATION (LOCAL DOMAIN) . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DEFAULT FOR POWERCORE PLUG-IN PRESETS . . . . . . . . . . . . . . . . . . . . . . . . . 34
TC Works Customer Support
5706 Corsa Avenue, Suite 107
Westlake Village, CA 91362
POWERCORE IN WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
DIRECT X WRAPPERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
POWERCORE FW MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
POWERCORE FW FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
POWER LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
POWER PULSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ERROR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
TECHNICAL SUPPORT
For immediate answers on many support questions, visit the
4 / POWERCORE
POWERCORE / 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED HARDWARE WARRANTY
WELCOME
POWERCORE is warranted against failure arising through faulty workmanship and materials for a peri-
od of one year from the date of purchase. All claims under this warranty must be made to TC
Electronic’s dealer or local representative in the country the product was purchased, or alternatively
directly to TC Electronic in Denmark. Before you do this, contact customer support to obtain an RMA
number for your correspondence. Products sent to us without prior authorization will be refused.
CONGRATULATIONS!
You are about to add a stack of rackmount-quality effects to your native recording
environment – and we are convinced that once you have used PowerCore on a few
sessions it will stay as an essential part of your equipment for years to come.
• Pack the product securely in its original shipping box
• Include a copy of your sales receipt
• Prepay postage and insure the shipment
• Enclose a note that describes the symptoms.
PowerCore is an exciting concept, putting an end to proprietary closed system
environments. With a range of hardware and software options, and its seamless
integration into the VST and Audio Units you will still be able to freely build the
system environment according to your needs – and benefit from the much greater
predictability of DSP-based systems at the same time.
Within the warranty period, the unit will be repaired at no charge for parts and labor.
This warranty remains valid only if the serial number on the card has not been removed, and if repairs
are performed only by parties authorized by TC. It does not cover damage due to misuse, accident
or neglect. The local representative and TC retain the exclusive rights to make such determinations on
the basis of inspection.
Liability is expressly excluded in respect of any third party or consequential loss or damage (direct
or indirect) however or whenever arising.
PowerCore is an open development platform – so make sure you check
party developers, such as Sonnox, TC Helicon, DSound, Access and Noveltech.
The 3rd party community is growing rapidly – so there won’t be a shortage of new
and cool tools!
Please note that there might be additional regulations in place in your country that differ from the
warranty rights granted in this document.
Please don’t hesitate to supply us with feedback – this way you can help us to keep
making products that will help you getting the job done.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ENJOY!
TC Electronic
CAUTION – Do not open the PowerCore FireWire/Compact. Risk of electric shock inside.
There are no user-serviceable parts inside. Refer servicing to qualified service personnel only.
Mount PowerCore FireWire/Compact with a little space above and below in a well ventilated
rack. Don't block the top or bottom. To prevent electrical shock or fire hazard, do no expose
PowerCore FireWire/Compact to rain or moisture. Do not rely solely on the front screws when
mounted in touring rack. Support the back of PowerCore FireWire as well. Please report any
shipment damage or equipment malfunctions to your dealer, TC distributor or the TC head
office in Denmark.
ATTENTION
• Only Plug-ins written especially for PowerCore will run on this platform
– native plug-ins run on your computers CPU will not take advantage of
PowerCore’s DSP-power.
• In this manual, PowerCore refers to all PowerCore types unless
other information is given.
• “PowerCore Unplugged” hardware is identical to PowerCore PCI mkII, but comes
with NO plug-ins included. Therefore, any reference to "included plug-ins" in this
manual does not apply to "PowerCore Unplugged".
POWERCORE / 7
Download from Www.Somanuals.com. All Manuals Search And Download.
POWERCORE SPECIFICATIONS
POWERCORE SYSTEM REQUIREMENTS
POWERCORE COMPACT
MAC
•
•
•
•
•
•
•
•
2 x Motorola 56367 DSP / 150 MHz
512k Word SRAM per DSP
PowerCore software 3.0 or higher
Mac OS X (10. 4 or higher)
1x 266 MHz Motorola 8245 PowerPC
8 MByte SDRAM on board
Power Requirements typically lower 10 W. Peak max. 20 W.
Operating temperature: 0°C – 40°C (32°F – 104°F)
Storage temperature: -30°C – 80°C (-22°F – 176°F)
Humidity: max. 90%, non-condensing
G4/G5 or Intel (1 GHz or faster)
512 MB RAM
VST or Audio Units compatible host application.
System must meet requirements of the host application
FireWire, Compact, X8 & PowerCore 6000:
400 MBit FireWire connector (IEEE 1394)
POWERCORE PCI MKII & POWERCORE UNPLUGGED
PCI mkII and Unplugged:
•
•
•
•
•
•
•
•
4 x Motorola 56367 DSP / 150 MHz
512k Word SRAM per DSP
A free PCI/PCI-X slot
1x 266 MHz Motorola 8245 PowerPC
32 MB SDRAM on board
Power Requirements typically lower 10 W. Peak max. 20 W
Operating temperature: 0°C – 50°C (32°F – 122°F )
Storage temperature: -30°C – 80°C (-22°F – 176°F)
Humidity: max. 90%, non-condensing
Express
A free PCI Express slot
PC
PowerCore software 3.0 or higher
Windows XP
POWERCORE EXPRESS
PIII 1,4 GHz or faster
512 MB RAM
VST compatible host application
System must meet requirements of the host application
•
•
•
•
•
•
•
•
4 x Motorola 56367 DSP / 150 MHz
512k Word SRAM per DSP
1x 266 MHz Motorola 8245 PowerPC
32 MB SDRAM on board
Power Requirements typically lower 10 W. Peak max. 20 W
Operating temperature: 0°C – 50°C (32°F – 122°F )
Storage temperature: -30°C – 80°C (-22°F – 176°F)
Humidity: max. 90%, non-condensing
FireWire, Compact, X8 & PowerCore 6000:
400 MBit FireWire connector (IEEE 1394)
PCI mkII and Unplugged:
A free PCI/PCI-X slot
POWERCORE FIREWIRE - X8 - 6000
Express
A free PCI Express slot
•
FIREWIRE version: 4 x Motorola 56367 DSP / 150 MHz
X8 and 6000 versions: 8 x Motorola 56367 DSP / 150 MHz)
512k Word SRAM per DSP
•
•
1x 266 MHz Motorola 8245 PowerPC
X8 and 6000 versions: 2 x 266 MHz Motorola 8245 PowerPC)
8 MByte SDRAM on board
•
X8 and 6000 versions: 2 x 8 MByte SDRAM on board)
Power Requirements typically lower 10 W. Peak max. 20 W.
Operating temperature: 0°C – 40°C (32°F – 104°F)
Storage temperature: -30°C – 80°C (-22°F – 176°F)
Humidity: max. 90%, non-condensing
•
•
•
•
Attention
All specifications and system requirements are subject to change without notice.
8 / POWERCORE
POWERCORE / 9
Download from Www.Somanuals.com. All Manuals Search And Download.
For detailed information on how to connect/install your PowerCore hardware please
refer to page 14-15.
SOFTWARE INSTALLATION GUIDE WINDOWS
We recommend installing the software before connecting/installing the hardware.
•
After connecting/installing the PowerCore hardware the computer may indicate
that it has “found new hardware” and the following “Welcome to the Found New
Hardware Wizard” may appear.
•
•
•
Close ALL running applications.
Insert the PowerCore CD in your computers CD-ROM drive.
The installer should start automatically. If it does not, then navigate to the CD
ROM drive and doubleclick the: SETUP.exe
•
The following screen appears:
•
•
•
•
Read, act and click NEXT.
The License agreement screen appears.
Read and check “I accept the license agreement”, if you agree; click NEXT.
Read the POWERCORE SOFTWARE INSTALLATION Read ME & Limited Hardware
Warranty and press NEXT.
•
•
Select “No, not this time” and press NEXT.
Now select “Install the software automatically” and press NEXT.
•
The installer now suggests a default location for installing the PowerCore package
•
After completing the software installation click FINISH and Windows will indicate
•
The installer is now ready to install the software.
Click NEXT to proceed or press BACK to re-enter the installation information.
To exit the installation press CANCEL.
that the installation is complete:
Congratulations - the installation is now complete.
•
When the installation is complete, connect/install your PowerCore hardware.
10 / POWERCORE
POWERCORE / 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE INSTALLATION GUIDE OSX
We recommend installing the software before connecting/installing the hardware.
MAC SETUP
We recommend installing the software before connecting or installing the
hardware.
•
It is now possible to perform a basic installation of the software (recommended).
Click UPGRADE/INSTALL to do so.
•
•
Insert the PowerCore CD in your Mac’s CD-ROM drive.
The install disk should appear on your desktop automatically. If it does not, open
a new Finder window and navigate to the CD.
•
The following dialog appears:
•
•
If you choose “Customize” instead the following screen appears.
•
•
•
Click CONTINUE.
Read the introduction and press CONTINUE.
The Read Me screen appears.
Here you have the opportunity to de-select parts of the installation. (Not
recommended for a standard installation)
•
•
•
Enter your Mac OS X username and password and press OK.
The installer now installs drivers and software.
After the installation you have the options shown below. Select and click
CONTINUE.
•
This describes the installation procedure as well as the Limited Hardware
Warranty. Read and click CONTINUE.
Note: You may also print or save this information before continuing.
•
•
Read the Software License Agreement and press CONTINUE.
The following screen appears.
Congratulations - the software installation is now complete.
•
•
Make sure that you have read and understood the Software License Agreement
and click AGREE.
Now connect/install you PowerCore hardware.
Select your system drive and click CONTINUE.
12 / POWERCORE
POWERCORE / 13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the card carefully, and make sure that it is fitted
POWERCORE HARDWARE INSTALLATION GUIDE
properly into the slot.
HARDWARE INSTALLATION
POWERCORE PCI MKII, EXPRESS & UNPLUGGED
In the following pages, we will show you in detail how to install the PowerCore PCI
mkII card in your computer. In this example we use a Windows based PC, but the
installation procedure will also work with Macs. Please note that the procedure for
opening and closing your computer case might differ. Make sure you consult the
operating manual of your computer for further details.
5. Now tighten the screw in order to secure the card.
1. Shut down your computer and make sure the power is
OFF and the power lead to your computer is
disconnected!
6. Close the case and then connect the power lead again.
2. Open your computer. Discharge any static electricity
from your clothes and body before you continue. This can
be done by touching the internal frame of the
computers case.
PowerCore PCI mkII & Unplugged Special
Jumper settings
PowerCore PCI mkII supports both 33MHz and
66MHz PCI bus speeds.
In its default position the PowerCore card will run
at a PCI bus speed of either 33MHz or 66MHz,
depending on your PCI bus speed. By moving the
jumper to the“Force 33MHz” position, the card is
forced to run at 33 MHz. We highly recommend
that you leave all jumper settings in their default
position, unless instructed by a TC Electronic
service technician to do otherwise. Other jumpers
on the card should be left untouched, as they are
used only for hardware testing purposes in a
qualified TC Service Center.
3. Remove the screw and the blind panel on the free PCI *)
slot you are planning to use.
*) PowerCore Express must be installed in a PCIe
slot. Check the specifications of your computer to
see if it facilitates PCIe.
J3
The PCI Express (PCIe) bus is a new incarnation of
the PCI bus. Note that PowerCore Express is
physically incompatible with a standard PCI port.
The PCI-X bus architecture used in most Mac G5-models is backwards
compatible with PCI. PowerCore PCI mkII is therefore compatible PCI-X based
models.
14 / POWERCORE
POWERCORE / 15
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INSTALLATION
POWERCORE FIREWIRE, X8, 6000 & COMPACT
THE POWERCORE CONTROL PANEL
Via the PowerCore Control panel you are able to monitor all connected
PowerCore items in your system.
1. Power off your computer!
2. Disconnect the power-cable from your PowerCore device.
3. Connect the included FireWire cable to a free FireWire port on your computer.
4. Connect the other end of the cable to a free FireWire port on your PowerCore.
5. Connect the power-cable to your PowerCore device and power up.
6. Start your computer.
•
•
•
The Status page indicates the DSP and memory consumption. Not only on the
individual PowerCore items, but also on the individual DSP circuits.
On the Plug-in page you are handle licenses, monitor free trial time and link to
purchase licenses for the desired plug-ins.
On the Setup page a few options are available to help you utilize your PowerCore
to its full potential.
NOTE:
Accessing the Control Panel in Windows
In Windows, the TC PowerCore control panel can be accessed from the Start Menu:
Start --> Settings --> Control Panel --> PowerCore
We STRONGLY recommend connecting the firewire cable
BEFORE powering up your PowerCore FireWire or connecting
the power-cable to your PowerCore Compact.
Accessing the Control Panel in Mac OS
In Mac OS, the PowerCore control panel can be accessed from the System
Preferences Menu in the Dock: System Preferences --> Other --> PowerCore
This procedure should ALWAYS be followed !
You must click on CONTINUE to open the control panel from the Preferences dialog.
STATUS PAGE
First let us take a look at the Status page.
PowerCore
Type icon
DSP and
Memory
Consumption
PowerCore Type icon
The PowerCore Type icon conveniently indicates the type of PowerCore device.
16 / POWERCORE
POWERCORE / 17
Download from Www.Somanuals.com. All Manuals Search And Download.
continued........
DSP and Memory Consumption
PLUG-INS PAGE
PowerCore PCI MkII (as in example) is equipped with 4 DSP and memory circuits.
Each DSP has an indicator for DSP Load, the percentage of each DSP used, as well
as Memory, indicating how much memory is in use on each DSP.
The plug-ins page is an overview page of all available plug-ins and their status.
Depending on the type of PowerCore hardware you are using, the plug-ins have
various status types.
The PowerCore 2.0 software features a new licensing system. The 2.x licensing
system provides new features, including full functional trial time and better overview
over the plug-ins.
Expanded Status page
The status page can be expanded by pressing the “MORE” key.
PowerCore 2.0 also works with the old 1.x licensing system, meaning that plug-ins
that are authorized for the 1.x will still run. You can still open the plug-ins and work
with them as you are used to, but 1.x licenses will not appear in the control panel.
Please also notice that not all 3rd party developers will make use of the 2.x licensing
system, and therefore there will be plug-ins that do not appear in the control panel.
Free Trial Period on optional plug-Ins
Optional plug-ins distributed by TC Electronic come with a free trial period. Once the
free trial period expires you will have to buy the plug-in for continued use.
A counter of the remaining free trial time for each plug-in is found on the plug-ins
page. Depending on the type of host application you are using, the time counts in
slightly different ways. With some host applications (such as Cubase) the counter is
running as soon as the plug-in is opened and also when the song is in stop mode.
With other applications (such as ProTools), the counter is running only when a signal
is passing through the plug-in in play mode.
Authentication ID
The Authentication ID contains your Serial Number and Board ID. This combination
of numbers is unique and you will need this to register your PowerCore.
To copy the numbers to the clipboard:
•
•
Right click on top of the ID number
Select “Copy authentication ID to clipboard”
Once the numbers are on the clipboard they are easily pasted into the online
registration form.
PLUG-INS
Nickname
informed about new releases and new plug-ins. Once a plug-ins is authorized the
plug-in will run on any connected PowerCore products in the system.
If you have several PowerCore devices in your system you may prefer to “Nickname”
the individual devices for better overview in the future.
The RESET button
Beware that there are a number of plug-ins that this list does not show:
The RESET button will reboot the PowerCore. This will terminate all plug-ins running
on this particular PowerCore! Should you ever find yourself needing to RESET the
PowerCore, you should save and close your session before you RESET.
Failing to do so will most likely result in various error messages from the host as it
will expect to see plug-ins that are not there.
1) TC Plug-ins that are using the old (non 2.x) version copy protection
2) Plug-ins from 3rd parties that use old (non 2.x) version copy protection
3) Plug-ins from 3rd parties that use iLok copy protection (for instance Sonnox plug-
ins)
Authorized correctly, these types will run absolutely fine without limitations, even
though they are not shown in the list.
18 / POWERCORE
POWERCORE / 19
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPE (PLUG-IN TYPE)
No info
STATUS
Enabled
The plug-in is activated.
The plug-in license is not version 2.x., and therefore there is no info available. This
is typically the case if the plug-in has been installed with an earlier version of the
PowerCore software.
19:59:59 – and counting
This counter shows the remaining time of the trial period of the plug-in.
Depending on the type of host application you are using, the time counts in slightly
different ways. With some host applications (such as Cubase) the counter is running
as soon as the plug-in is opened also when the song is in stop mode. With other
applications (such as ProTools), the counter is running only when a signal is passing
through the plug-in in play mode.
Not available
There is no info available because there is no PowerCore supporting the 2.x license
system available. This message appears when there are only PowerCore PCI/Elements
in the system.
Expired
ACTION
The license has expired.
Remove
Removed
The license has been removed.
It is possible to remove a license from you current PowerCore hardware and move the
license to another PowerCore unit or to sell the license should you wish to do so.
Beta
•
•
•
Click on the REMOVE button for the license you wish to remove.
Click OK to proceed.
Select at location where you want to save the file and click OK.
Beta version. This plug-in is a beta version and might not be fully functional.
Trial
This plug-in is a time limited trial version.The plug-in is fully functional until the end
of the trial period. Note: When the remaining trial period is above 4 days this is
indicated by: “> 4 days”
You have now removed the license from the PowerCore hardware. Next action is to
transfer the license back to your My Account.
•
•
•
Click Upload plug-in license.
Click BROWSE to locate your license file on your computer and click OK to
upload the license.
Bundled
This plug-in is bundled with one of the PowerCores in your system and is fully
functional.
Educational
That's it. The license has now been successfully removed from your PowerCore and
uploaded to your My Account.
Education version. Not for resale but fully functional.
NFR
Load License to another PowerCore of you own
Not for resale but fully functional.
Should you wish to load the license back onto another PowerCore unit belonging to
you, click Download plug-in license and assign it to another one of your PowerCore
products.
Full
Full version - fully functional.
Transfer License to another PowerCore user
In order to transfer a plug-in license to another PowerCore user, please contact the
TC Support Team and provide the following information:
Load License
If you buy an optional plug-in, you will receive a license file. Use the Load License
button to store the license on your PowerCore card.
-
-
-
Serial number and name of the product to be transferred.
TC My Account User ID / email address of the new user.
The registered PowerCore Authentication ID that the license should be transferred
to.
20 / POWERCORE
POWERCORE / 21
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM SETUP - plug-in loading
The System Setup options controls the way the plug-ins are loaded onto the DSPs in
your PowerCore system. There are three options:
SETUP PAGE
By clicking on the Setup tab in the control panel, you will be able to perform some
advanced tweaks to your PowerCore system.
Adjust for least host CPU consumption
Chose this setting if you experience clicks or dropouts.
High compatibility mode
This is the default setting and it will work perfectly for most setups.
Adjust for most Plug-Ins
This is the ideal setting if you use many small and low CPU consuming plug-ins.
SYSTEM SETUP - Buffer Multiplier
If you experience host CPU spikes you may need to increase the PowerCore’s buffer
size. The buffer multiplier increases your soundcards buffer setting by a factor 1,2,3
or 4. Increasing the buffer multiplier results in increased latency and should
therefore only be increased if CPU spikes actually occur.
SYSTEM INFORMATION
The System information indicates the current PowerCore software, drivers and Control
Panel versions.
Check for update
By pressing the CHECK FOR UPDATE button the software will automatically access
the internet and check to see if a newer version is available for download. Before
downloading you will be prompted and asked to confirm the download.
System Report
If for some reason you need to get in contact with our support center they will ask to
see a system report. The system report is a small text-file containing all relevant
information of your current system. To create a system report, press the SYSTEM
REPORT button. The file will be saved on your desktop. The system report file will
not contain any personal information, and TC will use the information only in order to
help with issues.
22 / POWERCORE
POWERCORE / 23
Download from Www.Somanuals.com. All Manuals Search And Download.
96 kHz PROCESSING
GETTING THE MOST FROM POWERCORE
The included PowerCore plug-ins support 96 kHz processing. The golden rule of DSP
performance is: the higher the sample rate, the greater the DSP performance
required. So, a plug-in that requires 50% of a DSP at 48 kHz will require 100% of a
DSP at 96 kHz, as a doubling of sample rate also doubles the resulting DSP
performance required. As mentioned above, a plug-in will enter the Disabled State if
it can not handle a certain sample rate. In that case, simply switch back to the
supported sample rate.
BUFFER SIZES
For optimal performance, set your audio buffer size (typically adjusted in the I/O
setup of your host application) to a value between 256 and 1024 samples. Rule of
thumb: The larger the audio buffer size, the lower your PowerCore plug-in’s
performance overhead on the DSPs and the CPU of the host computer. PowerCore is
optimized for best performance when using a buffer setting of 1024 samples. The
minimum I/O buffer size for PowerCore to work properly is 128 samples.
THE DISABLED STATE
LATENCY
When the Disabled State becomes active, the plug-in is bypassed due to a lack of
available DSP performance. This can happen when increasing the sample rate or you
try to load too many plug-ins. Only the audio processing will be bypassed on a
disabled plug-in – all of the parameters and presets updates will still be active,
preventing problems later on should you not notice that a plug-in has become
disabled.
WHAT IS LATENCY?
PowerCore plug-ins have a slight delay before the processed signal is returned to the
host application. The delay can be somewhat disorienting, resulting in an effect that
sounds like it is not in sync with the tempo of your song. To accommodate this, most
applications have something called Automatic Delay Compensation. Plug-ins report
back to the host application with a processing time, and the application offsets the
audio so that everything "lines up”.
Let us say that this error occurs when trying to load MegaReverb. In this case, you
will receive the following warning: "The following error occurred with the PowerCore
Effect ‘MegaReverb’: The PowerCore does not have enough free DSP resources
available to load the Plug-in. "
The COMPENSATOR plug-in, included with your PowerCore, allows you to easily
setup delay compensation manually. Check the COMPENSATOR manual-PDF on your
installation CD for details.
As an additional warning, there will be a status indication directly within the plug-in
that is disabled.
NO LATENCY MODE
The PowerCore plug-ins offer the No Latency Mode. This mode is an alternative way
of communicating with the PowerCore. To enter No Latency Mode, click on the
PowerCore logo on the bottom of the plug-in. When enabled, the PowerCore logo will
have a red glow to indicate operation.
Figure 1: Many of the PowerCore plug-ins have a Disabled LED at the bottom of the
plug-in that will light-up red when disabled.
In most cases, No Latency Mode is not required as this much power comes at a
price; No Latency Mode will place a significant load on your host CPU! However, No
Latency Mode is ideal for record monitoring with a PowerCore reverb effect or playing
a PowerCore synth.
Some PowerCore plug-ins, such as EQSAT Custom, 24/7•C or the CLASSIC VERB,
will display the Disabled State message directly in the user interface.
LATENCY IN THE MASTER FADER
When using PowerCore plug-ins in the Master output channel, latency is not an issue
as all of the audio is uniformly delayed.
Figure 2: The 24/7•C will appear as though the "lights
are out” and the disabled message will appear in the
VU Meter display.
24 / POWERCORE
POWERCORE / 25
Download from Www.Somanuals.com. All Manuals Search And Download.
CHORUS-DELAY
USING POWERCORE PLUG-INS
CHORUS-DELAY is modeled after the TC Electronic 1210
Spatial Expander, and provides you with simultaneous
modulation effects such as chorus and flange as well as slap
delay. To make tempo-based projects easier to manage, we
have added a BPM-input scale to the delay time adjustment
parameter. CHORUS-DELAY is also available in the TDM
bundle of plug-ins, TC TOOLS for ProTools HD.
PowerCore plug-ins act and behave in the exact same manner as "traditional” VST or
Audio Units plug-ins, with the exception that they are using the processing power of
the PowerCore DSPs, - not your host computer’s CPU.
PowerCore plug-ins can be used in Multi-Track audio applications, stereo mastering
applications, and even audio capable video-editing applications that can host one or
more of the supported PowerCore plug-in formats.
CLASSIC VERB
BASE PACKAGE
CLASSIC VERB enhances the out-of-the-box reverb flexibility
of PowerCore significantly! This reverb processor adds a
distinctly warm and lush reverb effect often associated with
big expensive hardware processors. It is a whole different way
to create the effect compared to the traditional reverb
philosophy or accurate room reproduction, as you will find
with the reverbs provided by MegaReverb.
- INCLUDED PLUG-INS WITH ALL POWERCORES*
A detailed description of the plug-ins’ features as well as instructions for operation
can be found in the associated PDF-manual on your installation CD.
Please note that the list of included plug-in bundle is subject to change without
notice. Refer to your product box for more details on which plug-ins are bundled with
your PowerCore purchase !!
EQSAT CUSTOM
24/7·C LIMITING AMPLIFIER
EQSat provides you with crystal clear mastering quality
equalization. This EQ’s algorithm is taken directly from the
TC Electronic Finalizer mastering processor! Featuring low
and high shelving bands as well as three stereo bands of
Parametric EQ, EQSat Custom is ideal for all of your
precision equalization needs. The EQSat algorithm is also
available in the TDM bundle of plug-ins, TC TOOLS for
ProTools HD.
Convincing vintage compression and limiting using one of the
most desired vintage models for PowerCore! 24/7·C was
inspired by one of the vintage processors synonymous with classic dynamics process-
ing for mixing and mastering. This plug-in recreates the details of the sound and user
interface of this hardware processor as closely as possible, delivering virtual vintage
at its best. The user interface is simple and straight-forward: increasing the input will
drive the limiter depending on the selected ratio.
Even the famous 4-button-mode was implemented. A special new feature is an auto-
gain sensing for the output parameter, that adjusts the output depending on the pro-
gram material.
NOVELTECH CHARACTERTM
Character is the result of the latest scientific research in
digital signal processing and psychoacoustic.
Basic audio processing tools such as EQs and compressors
involve a large number of technical parameters, which have
to be set to correct values in order to get the desired result. The Character™
intelligently enhances the relevant characteristics found in the source, working across
a complex set of connected parameters, and not only boosting e.g. one specific
frequency. This innovative approach allows users to get to the desired results much
faster, as only three parameters need tweaking!
Character can dramatically reshape the character of any sound and has 3 different
processing modes ensure adaptability to all types of audio material.
*Does not apply to PowerCore Unplugged!
26 / POWERCORE
POWERCORE / 27
Download from Www.Somanuals.com. All Manuals Search And Download.
FILTROID
POWERCORE 01
With its dual filters and extensive modulation capabilities,
Filtroid brings the sound of analog filter banks to PowerCore.
POWERCORE 01 is an emulation of a classic mono synth.
This single oscillator synth can produce vicious leads and fat
basses, without draining the CPU of your computer.
Filtroid consists of two filters with low-, hi- and band-pass
shapes with 12, 18 or 24 db slope characteristics. The filters
can be used in series or parallel for the utmost creative
POWERCORE CL
control, and the external side-chain input provision allows for modulation of the filter
from another track.
Extensive modulation capabilities include independent LFOs per filter and an
envelope follower. Tempo sync ensures that filter movements are always synchronized
to the speed of the sequencer, and a distortion unit adds an additional edge to the
sound, if desired.
POWERCORE CL employs a different compression algorithm
than the one found in the VOICESTRIP or the 24/7·C,
instead emulating the behavior of an industry-standard
analog compressor, aiming at general purpose dynamics
processing rather than specific applications as provided with
the VOICESTRIP or the 24/7·C.
With serial or parallel filter routing, massive modulation options, side chain input,
resonance with self-oscillation, envelope follower, distortion and out of phase
modulation, PowerCore users have all the tools they need to make the most extreme
filter effects.
VOICESTRIP
VOICESTRIP is all-in-one voice sound processing and is
widely used among vocal producers that aim to have it all!
This highly integrated plug-in is a complete channel strip for
voice sound processing, with Compression, DeEssing, a
dedicated Voice EQ, Lo Cut Filter and Gate!
MASTER X3
Knock out Punch for any mixes or masters. Period. MASTER
X3 is the virtual incarnation of the TC Electronic Finalizer,
the standard mastering processor in the pro audio field.
MASTER X3 expedites the mastering process by integrating
several phases of mastering into a single, easy to use
interface. It features multiband processing with expansion,
TUBIFEX
Tubifex includes three tube stages and a speaker simulator
for truly convincing amp modeling. Each of the three stages
is based on a classic 12AX7 design and can be individually
adjusted making the sonic possibilities virtually endless, from
warm tones to screaming overdrive. The speaker simulator
compression and limiting separately for each band. High quality uncorrelated
dithering is included as well. The intuitive user interface features many new ideas to
make the critical mastering process faster and easier. The overall processing
characteristics are controlled via "Target Curves" that simplify the handling by
providing a global processing style for all bands in all modules. The interaction
between the bands can be fine tuned by applying "Target Factors" which determine
the frequency focus of each processing module, significantly reducing the number of
required user parameters to set this complex process up. "Soft Clipping" even
provides "analog" sound whenever desired. MASTER X3 is also available in the TDM
format for ProTools HD.
was derived directly from the impulse measurements of a 2 x
12 cabinet. Additional adjustments can be made with the
virtual microphone placement control, which simulates the subtle tonal variations
achieved with different mic techniques.
Tubifex also includes a fingerprint-based noise reduction filter that allows settings to
be saved independently from the amp settings. An expander enables further
improvement of the overall sound. As a 'hybrid' plug-in, Tubifex uses both native and
PowerCore DSP resources. Combining the strengths of both worlds results in very low-
latency processing, which enables guitar players to use Tubifex in real-time.
MEGAREVERB
MEGAREVERB will provide you with studio-quality reverb
that TC Electronic is famous for. MEGAREVERB’S technology
is taken directly from the Core 1 and 2 algorithms of the TC
Electronic M5000, with an enhanced tail design based on
some more recent innovations in reverberation from TC
Electronic. MEGAREVERB is also available in the TDM
bundle of plug-ins, TC TOOLS for ProTools HD.
28 / POWERCORE
POWERCORE / 29
Download from Www.Somanuals.com. All Manuals Search And Download.
DENOISE
ADDITIONAL PLUG-INS WITH POWERCORE 6000
DeNoise comes from TC's acclaimed Restoration Suite
bundle.
In addition to the Base Plug-ins described in the previous manual section, PowerCore
6000 also includes the following plug-ins from System 6000
DeNoise is optimized for broadband noise removal,
from tape hiss to static environmental noise.
VSS3
The VSS3 Stereo Source Reverb for ProTools and PowerCore
is a genuine and original reverb directly ported from the
System 6000. The VSS3 algorithm was researched and fine-
tuned by TC engineers for over a year, resulting in an
exceptionally precise tool. Similar to the chaotic response of
a natural room, the VSS3 reacts differently to identical
signals.
DeNoise is fingerprint-based and its edit tools allow manual adjustment of the
analyzed fingerprints for even more precise processing results.
In version 1.5 the DeNoise plug-in has been updated with an 'auto' mode that makes
it possible to remove noise from material where it is not possible to take a fingerprint
– for instance if there are no parts with noise only. Fingerprints can now be adjusted
independently for left and right channels.
Used for effects purposes, extensive modulation possibilities are offered for the
creation of detuned or chorused sustain effects for e.g. vocal, guitar, piano or horns.
Inherent in the VSS3 algorithm there are almost 800 parameters, equaling an
astronomical amount of combinations, and this impressive set of parameters has
been condensed to a very substantial and pertinent user interface.
DYNAMIC EQ
Dynamic EQ is a new tool for any mixing or mastering
situation. This virtual processor eliminates the
shortcomings of static EQ by providing a dynamically
applied equalization.
With the VSS3 you get a package of presets that have become industry standards.
The sound of VSS3 can be heard on thousands of albums and films.
The Dynamic EQ plug-in offers up to four definable
bands working either in static or dynamic mode, or in
MD3
a mixture of both. Each of the bands can be configured as a parametric EQ or as a
high or low shelving filter. The side-chain bands can be unlinked from the processing
bands, so the high frequency content of a mix can control the low-end and vice
versa. The pristine processing of this plug-in is all in 48-bit double precision, and
may even be used in a phase linear mode, that is generous with transparent results.
The MD3 Stereo Mastering package brings processing only
known from the System 6000 to ProTools and PowerCore.
This package presents professional production and mastering
possibilities to the realm of DAWs, and integrates smoothly
with serious music and film editing applications.
Dynamic EQ represents a new generation of mastering tools for the POWERCORE
platform and this virtual processor eliminates the shortcomings of static EQ by
providing a marriage between dynamics processing and EQ.
Dual Mono and Stereo dynamics processing in three frequency bands. By offering a
true side-chain split structure, MD3 is also capable of demanding mono material
compression/limiting on two separate channels, not found in other multi-band
dynamics processors. MD3 can be regarded as a high-end mastering tool. M and S
components of a stereo signal can be processed separately and provide even more
control making full use of the Spectral Stereo Enhancer.
On top of the plug-ins that are included with PowerCore, there is a broad selection of
optional plug-ins available. These plug-ins are developed by TC Electronic as well as
a number of 3rd party developers like Sonnox, Access, Novation, TC Helicon and
Dsound. The optional plug-ins are available from store around the world and from
TC's web shop.
When you buy an optional plug-in, it will be licensed to your PowerCore hardware and
sent to you by email. Therefore, this procedure requires you to register your
PowerCore and your email address.
BRICKWALL LIMITER
If you are concerned about audio quality at the end listener,
or have a desire to conserve talent, the BrickWall Limiter is
the solution. While it cannot prevent destruction of dynamic
range from happening at earlier stages in the production
process, it does get rid of the signals known to generate
distortion in consumer CD players, radio processors and data
reduction codecs.
30 / POWERCORE
POWERCORE / 31
Download from Www.Somanuals.com. All Manuals Search And Download.
NONLIN 2
UNWRAP
NonLin2 Stereo Effects Reverb - from the legendary System
6000
UnWrap - Available for PowerCore & TDM
This full version mastering and film up-converter algorithm
offers a high level of sophistication with unprecedented
control and resolution. An abundance of parameters
facilitates the conversion of stereo and LtRt sources to 5.1
while remaining faithful to the original mix’s width, timbre,
spaciousness and other significant factors.
The NonLin2 Stereo Effects Reverb for ProTools and
PowerCore is another world class reverb directly ported from
the System 6000.
NonLin2 is an effect reverb, which differs from the traditional natural sounding TC
reverbs. NonLin2 is capable of generating compact vocal ambience, percussive and
dramatic drum sounds, reverse reverbs and completely new “twisted” effects.
Featuring an amplitude envelope that is capable of rendering an untriggered gated
reverb and a 'twist' parameter, which can radically alter the sound, this plug-in
delivers a serious advantage over other gated reverbs.
With its wealth of controls, UnWrap™ is a benchmark in film and music production.
Whether you lack time to do a conventional 5.1 mix or a multitrack source simply
doesn’t exist – UnWrap™ facilitates smooth and fast stereo to 5.1 up-conversion.
Once processed, the 5.1 output can be subsequently down-mixed to stereo again
with no sonic penalties. Take a preset tour to spark your creativity, or start a new up-
mix from scratch. Processing is double precision, capable of running at any sample
rate between 44.1 and 96 kHz.
The easy-to-tailor and compact room-feel that this reverb adds to any lead vocal will
set your mixes apart. As a producer or studio engineer, you'll be delighted by the
creative power that this master tool delivers and it won't be long before you wonder
how you coped without it.
UnWrap™ includes customized up-conversion presets for film production and music
mastering and comes with settings to complement it all.
DVR 2
The DVR2 Digital Vintage Reverb is another great
professional reverb ported from the revered System 6000. It
is available as a plug-in for ProTools and PowerCore.
Add to the default presets the ability to time-align all channels at sample precision,
widen or narrow the image, control the amount of Center and LFE channel to be
used, change filters and envelopes, and you begin to get an idea of the power of this
plug-in.
TC Electronic has put much effort into preserving the
qualities of the original processor, including sweet
modulation, spectral balance, spaciousness and saturation. But not only is DVR2 the
most precise EMT250 emulation up to now, it also emulates its predecessor in the
way parameters interact for different settings. DVR2 comes with customizable
presets, focus fields for tweaking and navigation, and a built-in preset converter
allowing seamless import of DVR2 presets from System 6000.
TAP FACTORY - MULTITAP DELAY
Transcend the Average Delay - A Tweaker’s Paradise
Let your creativity run wild with this delay/reverb hybrid.
Easily design custom out-of-this-world effects that cross the
With the DVR2 for ProTools and PowerCore, it is now possible to save processing
power on the System 6000 for other tasks - the choice is yours.
borders between Ambience, Early Reflections, Reverb and Delay.
Tap Factory makes customization of your sound a breeze and brings radical
signatures to your productions. Tap Factory’s extremely intuitive and clean user
interface allows you to make individual parameter settings for each of its 24 taps
within seconds.
The vintage reset function produces a sound very close to a well preserved EMT250,
which is still a favorite on lead vocal in studios fortunate enough to own one. The
high resolution parameters allow for lower noise, extension of bandwidth, and control
of the amount of chorusing.
Tap Factory includes a bonus LE version that allows you to run multiple instances per
DSP on current PowerCore systems and supports first generation PowerCore
hardware.
32 / POWERCORE
POWERCORE / 33
Download from Www.Somanuals.com. All Manuals Search And Download.
POWERCORE IN WINDOWS
POWERCORE IN MAC OS X
If you would like to access the PowerCore plug-ins from within your Windows based
sequencing environment, you need to install the supplied plug-ins in the same
location as all of your other VST plug-ins. The installer scans for all of the
appropriate VSTPlugIns folders and prompts you to select a destination directory
during installation.
PowerCore supports both the VST and Audio Units plug-in formats in OS X.
PowerCore plug-ins are always installed into the same locations in OS X, which is
extremely convenient, especially when using multiple audio applications that rely on
the same pool of plug-ins.
Audio Units are supported by an "adapter” that transparently "adapts” the VST plug-
in to the Audio Units format. In an Audio Units Host Application like Logic, the
plug-in will appear and behave as a standard Audio Units plug-in. Our Audio Units
Wrapper will automatically work with Sonnox, TC-Helicon, Access and other 3rd party
PowerCore plug-ins.
Program Files/Steinberg/VSTPlugIns/PowerCore
Program Files/Emagic/Logic Audio Platinum/VSTPlugIns/PowerCore
DIRECT X WRAPPERS
Some Windows based applications use the DirectX plug-in format instead of the VST
plug-in format. PowerCore does not directly support DirectX. If you would like to use
PowerCore in a DirectX application such as Sound Forge, we suggest that you use a
wrapper such as the "VST-DX Adapter” from Cakewalk. This is available for a fee
directly from the Cakewalk website.
OS X Domains
OS X is designed for networking, and uses a hierarchy of "virtual locations" called
Domains. PowerCore plug-ins are installed into one of two domains: the Local
Domain, and the User Domain. The Local Domain can have multiple users.
Please note that as TC does not support DirectX, you should also contact customer
support for the creator of your DirectX wrapper or adapter should you encounter
problems with PowerCore plug-ins within a DirectX application
PowerCore plug-ins are installed in the Local Domain, while presets are installed in
the User Domain of the person installing the software. Each plug-in is installed as a
VST plug-in. Our TCAU Audio Unit Component takes care of the Audio Unit support.
POWERCORE FIREWIRE MESSAGES
POWERCORE FW FRONT PANEL
Getting Audio Unit Support for optional
PowerCore Plug-ins
When new optional plug-ins are installed,
you'll need to update the TCAU Audio Unit
component in order to gain AudioUnit
support for these new plug-ins. This can
be done by launching the actual
PowerCore installer, and selecting the
"Refresh AudioUnits Only" installation
option.
The blue Power Pulse and the other LEDs on the front panel are more than just a
lightshow: they provide feedback about the PowerCore FireWire operating
environment.
POWER LED
Default PowerCore Plug-in Locations (LOCAL DOMAIN)
Nothing fancy here. This LED lights up when power is on.
OS X/Library/Audio/Plug-ins/VST
POWER PULSE
PowerCore Control Panel Location
During boot, the Power Pulse will rise to maximum brightness, and then begin to
pulse, until driver and PowerCore board OS is loaded. The Power Pulse will flash
once to indicate when a plug-in is successfully loaded. After the first plug-in is
loaded, the Power Pulse will enter steady state.
OS X/Applications
Default Location PowerCore plug-in presets
~/Library/Applications Support/PowerCore
ERROR LED
The Error Led will only light up when there is something wrong with the unit. Should
the Error LED ever become active, there probably is a hardware problem and you
should contact TC support.
34 / POWERCORE
POWERCORE / 35
Download from Www.Somanuals.com. All Manuals Search And Download.
My source audio is mono after inserting a PowerCore plug-in.
TROUBLE SHOOTING
There are different versions of many PowerCore plug-ins, to provide you with a
maximum of flexibility. Depending on the plug-in, you might have mono/mono,
mono/stereo and stereo/stereo versions of each plug-in. If your host application
displays all versions to select from, make sure you select the stereo version for stereo
processing! So running a mono/mono or mono/stereo plug-in would merge your source
material to mono before processing.
Where can I download the latest PowerCore drivers?
We are continuously working on improving the PowerCore software. Therefore we
recommend to check our website for the latest software, prior to installing the
software that came with the product to make sure you have the most current version.
The latest version of the PowerCore Software can be downloaded from the TC
PowerCore product pages. Locate your PowerCore in the Product Menu and select
"Software" from the product sub-page. Next to the latest version of the software, you
will also find the software version history.
The plug-in doesn’t open or there is no audio when I activate the plug-in.
If this is the case, there might be an issue with the plug-in’s authorization. In the
case of the included plug-ins, please reinstall the plug-ins – if that doesn’t
help,contact customer support.
I can run half the number of effects at 96 kHz than I can at 48 kHz.
With optional PowerCore plug-ins, you can freely make backup-copies of plug-ins that
you have purchased – but, with the exception of the included plug-ins, you can not
copy them over to other systems and expect them to function! Each card is unique,
and the software is unique for each card, too! Contact your plug-in manufacturer in
the case you have authorization problems such as this.
This is correct! When you double sample rate, you double the DSP resources
required!
PowerCore plug-ins don’t show in my applications plug-in selection dialog.
Please double-check that you have installed the plug-ins to your application’s
VST/AudioUnit plug-in folder. If you are not able to see ALL of your PowerCore plug-
ins, please read the next point!
The audio is corrupted.
The minimum I/O buffer size for PowerCore to work properly is 128 samples –
please verify the I/O buffer settings in your host application. We recommend 1024
samples for a minimal "hit” on the host!
I don’t see all PowerCore plug-ins in my native mixer’s inserts, sends or master.
Like other VST/AudioUnit plug-ins, PowerCore plug-ins might come in different
versions (mono/mono, mono/stereo, stereo/stereo). Depending on your host
application and the plug-in, you might only see the version appropriate for e.g. the
inserts or sends.
Every-time I load a plug-in in LOGIC or DIGITAL PERFORMER, my application Quits.
When you use a PowerCore plug-in in an Audio Units application such as LOGIC or
DIGITAL PERFORMER, you must have the plug-ins installed into both the Audio
Units and VST plug-ins folders of your system. If you remove the VST plug-ins, then
the Audio Unit versions will not work. If you experience application crashes when
loading a PowerCore plug-in, please reinstall the plug-ins to make sure that the plug-
ins are included in both locations.
The input of my PowerCore plug-in is clipping (and/or I hear distorted audio).
It is very important to avoid clipping of the input signal – the signal you send into a
PowerCore plug-in should not be greater than 0 dBFS! We suggest you leave some
marginal headroom!
36 / POWERCORE
POWERCORE / 37
Download from Www.Somanuals.com. All Manuals Search And Download.
FURTHER SUPPORT RESOURCES
NOTES
TC ELECTRONIC KNOWLEDGEBASE
In case none of the above answered your questions,
In the unlikely case that none of the answers in our Knowledgebase help you, you
should send an email to the TC Support Team.
CONTACTING THE TC ELECTRONIC SUPPORT TEAM
Please have the following information at hand when you contact the TC Support
Team:
1. Authentication ID of your PowerCore.
This information can be found in the PowerCore control panel under the STATUS tab.
Please refer to page 17 on how to locate and open your PowerCore control panel.
2. System details.
This means we need to know your operating system version.
Are you on Windows XP SP2 or Mac OSX 10.2.8? Be sure to note this down before
you get in touch with us.
What is your CPU speed and amount of RAM?
Under Windows this information can be found My Computer > Properties > General.
Under MacOS X go to the Applications folder > Utilities and open "System Profiles".
Any special modifications to the hardware of the computer? Please, make a note of
this too.
3. Peripherals.
What other stuff are you using along with the PowerCore and your computer? Any
PCI-cards, USB-devices, FireWire devices?
4. PowerCore driver version.
This information can be found in the PowerCore control panel under the
STATUS tab. Please refer to page 17 on how to locate and open your PowerCore
control panel.
5. Nature of the problem.
Are you getting any error messages? If so, what do they say? Be sure to note down
the complete error message text as it contains useful information for the TC Support
Team. Steps to reproduce the problem. What do you do exactly to make the problem
appear? Please describe in detail, the steps necessary to reproduce the problem.
We know this is a lot of details but in most cases knowing these things in advance
will help the TC Support Team answer your query faster!
38 / POWERCORE
POWERCORE / 39
Download from Www.Somanuals.com. All Manuals Search And Download.
© BY TC ELECTRONIC A/S. ALL PRODUCT AND COMPANY NAMES ARE TRADEMARKS OF THEIR
RESPECTIVE OWNERS. ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
ALL RIGHTS RESERVED.
Download from Www.Somanuals.com. All Manuals Search And Download.
|