Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction Manual – HD-338
Safety precautions
• Do not use this unit on slippery surfaces.
• Do not step on the platform when wet.
Important notes for users
Recorded data may be lost if the unit is used incorrectly or is exposed to
electrical power surges. TANITA assumes no responsibility for any kind of loss
of recorded data. TANITA assumes no responsibility for damage or loss caused
by these units, or any claim made by a third person.
Display and keys
Up button
Set button
Down button
Personal key
Personal key /
Off button
Specifications
Maximum capacity: 350 lb (160 kg)
Graduations: 0.2 lb (0.1 kg)
Power supply: Two 3-volt CR2032 replaceable lithium batteries (included)
Before use
1. Insert the supplied batteries as explained in the next section. Please note
that if the batteries were inserted at the factory, their energy level may
have decreased.
2. Set personal data. Please see page 6 for details.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting/Replacing the batteries
The battery box is located on the back of the measuring platform.
Two 3-volt CR2032 replaceable lithium batteries
Lithium batteries can typically be used for many
years before replacement is necessary. When the
low battery sign, “LO” appears on the LCD, please
replace with two new lithium batteries.
Gently remove the battery cover and pull the
battery box out carefully. Slide the battery compartment, as shown. Remove
the old batteries and stack new batteries with positive (+) side up. Replace the
battery compartment and battery box cover.
Weight Mode Switch
Select your preferred weight mode using the weight mode switch
located on the rear of the scale.
KG LB
Positioning the unit
Place the measuring platform on a hard, flat surface where there is minimal
vibration to ensure safe and accurate measurement.
NOTE: To avoid possible injury, do not step on the edge of the platform.
Handling tips
• Do not attempt to disassemble the unit.
• Store the unit horizontally, and place it so that the buttons will not be
pressed accidentally.
• Avoid excessive impact or vibration to the unit.
• Place the unit in an area free from direct sunlight, heating equipment, high
humidity, or extreme temperature change.
• Never submerge the scale in water or spill chemical liquids on it. To clean,
use a dampened cloth and mild detergent.
• Do not drop any objects onto the platform.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Features
How the Scale Determines Your Auto Goal Weight
During the programming process, you will enter your height. Once your height
is entered, the scale automatically suggests your ideal goal weight corresponding
to a Body Mass Index (BMI). According to National Institutes of Health, the ideal
BMI range is 18.5-24.9. If your current BMI is above 24, the scale automatically
suggests a target weight corresponding to a Body Mass Index (BMI) of 24.
If your current BMI is 24 or below, the scale automatically suggests a target
weight corresponding to a Body Mass Index (BMI) of 22.
Once the auto goal weight is given, you still have the option to change
to your desired goal weight (= Input Goal Weight). Use the + or - keys
to change to desired goal weight.
How the Scale Determines Your Step Goals (Milestones)
Your Jenny Craig HealthyTrack Scale automatically establishes realistic step
goals (milestones) in increments of 5 lb or greater depending on your target
weight established by the user. If your weight loss is
9.8 lb or less – you will have 1 step
14.8 lb or less – you will have 2 steps
19.8 lb or less – you will have 3 steps
20.0 lb or greater – you will have 4 steps
NOTE: Users will not be able to change the steps once they are established
by scale.
Body Mass Index (BMI)
Underweight
Normal Weight
Overweight
Obese
WEIGHT (LBS)
HEIGHT
100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 245 250
21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 47 48 49 50 51
20 21 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
19 20 20 22 23 24 25 26 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 43 44 46 46 47
18 19 20 21 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 38 39 40 40 41 42 43 44 45 46
18 19 19 20 21 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 38 39 39 40 41 42 43 43 44
17 18 19 20 21 21 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 38 38 39 39 40 41 42 43
17 17 18 19 20 21 22 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 37 37 38 39 40 41 42
16 17 18 19 19 20 21 22 23 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 36 36 37 38 39 40 40
15 16 17 18 19 20 20 21 22 23 23 24 25 26 27 27 28 29 30 31 32 33 34 35 35 35 36 37 38 38 39
15 16 17 17 18 19 20 21 21 22 23 24 24 25 26 27 27 28 29 30 31 32 33 34 34 34 35 36 36 37 38
15 16 16 17 18 18 19 20 21 21 22 23 24 24 25 26 27 27 28 29 30 31 32 33 33 33 34 35 35 36 37
14 15 16 17 17 18 19 19 20 21 22 22 23 24 24 25 26 27 27 28 29 30 31 32 32 32 33 34 34 35 36
14 15 15 16 17 17 18 19 20 20 21 22 22 23 24 24 25 26 26 27 28 29 30 31 31 31 32 33 33 34 35
14 14 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 26 27 28 29 30 30 31 31 32 33 33 34
13 14 15 15 16 16 17 18 18 19 20 20 21 22 22 23 24 24 25 26 26 27 28 29 29 30 30 31 32 32 33
13 13 14 15 16 16 17 17 18 19 19 20 21 21 22 22 23 24 24 25 26 26 27 28 28 29 30 30 31 31 32
12 13 14 14 16 16 16 17 17 18 19 19 20 21 21 22 22 23 24 24 25 26 26 27 27 28 29 29 30 31 31
12 13 13 14 15 15 16 16 17 18 18 19 19 20 21 21 22 23 23 24 24 25 26 26 27 27 28 29 29 30 30
4'10"
4'11"
5'0"
5'1"
5'2"
5'3"
5'4"
5'5"
5'6"
5'7"
5'8"
5'9"
5'10"
5'11"
6'0"
6'1"
6'2"
6'3"
6'4"
Source: National Institutes of Health
Please consult with your physician before you start your diet program.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting (resetting) personal data in memory
The unit can be operated only if data has been programmed into one of the
personal data memories.
Place your scale on a flat, even floor.You will need to measure your
current weight during this process.
1. Turn on the power
Press SET button to turn on the unit. The unit will beep to confirm activation.
The personal key number will flash.
2. Select a personal key number
Press the Up / Down buttons to select a personal key number (1-2). Once
you reach the personal key number you wish to use, press the SET button.
The unit will beep once to confirm.
3. Specify the height
The display defaults to 5' 7" (170cm). Use Up / Down buttons to specify
height and then press the SET button. The unit will beep once to confirm.
NOTE: Height setting range is from 3' 4" – 7' 3" (100 cm – 220 cm)
4. Measuring weight
Make sure that the scale is placed on a flat, even floor.
When “0.0” displays, step on the platform. The result will be displayed and
will beep twice to confirm.You may then step off the scale.
NOTE: “Err” appears when the unit cannot accurately measure your weight
or it detects movement. The scale will automatically shut off after
20 seconds.
5. Select “Auto Goal Weight” or “Input Goal Weight”
The scale displays your “Auto Goal Weight.”You may press the SET button
to confirm. The unit will beep once to confirm. If you wish to change the goal
weight, use Up / Down buttons to set goal weight and then press the SET
button. The unit will beep once to confirm. “Input Goal Weight” icon will appear.
NOTE: “Input Goal Weight” setting range is ± 99 lb (± 50 kg) from the
current weight.
6. Select CLASSIC Mode or WEIGHTLESS Mode (See description below.)
The display defaults to Classic Mode. Use Up / Down buttons to select
Classic Mode or Weightless Mode and press the SET button.The unit will
beep twice to confirm and store the personal data. The scale will then
automatically shut off.
• Classic Mode will display your current weight in the center of the display.
• Weightless Mode will not display your current weight; instead your
“Since Start” weight and “Since Last” weight will flash alternately
in the center of the display.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
• Thirty seconds or more of inactivity will cause automatic shut off during this
process. No data will be saved as a result.
• If you make a mistake or wish to turn the unit off before you complete the
programming, press and hold the “1/OFF” button for three seconds or more
to turn the unit off. No data will be saved.
Classic and Weightless Mode
Classic Mode
The LCD displays the actual weight, the weight change (loss/gain) from
previous reading in lb/kg, weight change (loss/gain) since Day 1 in lb/kg,
% achieved toward the goal, and % achieved within the step in %.
Weightless Mode (Privacy Mode)
The LCD does not display the actual weight. All other information from Classic
Mode will be displayed.
This unique and patented Weightless Mode allows you to maintain your actual
weight in privacy from other household members. By selecting this mode, your
actual weight is not displayed, but only your progress. All other features of the
Classic Mode remain the same.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for use
Classic and Weightless Mode
NOTE:
• Please set your personal data before operating the scale.
• If you wish to turn the unit off before automatic shut off, press the “1/OFF”
button for three seconds or more.
1. Select personal key and step on scale
Press personal key and the display will show “0.0.”
Step onto the platform.
NOTE:
• If you step onto the platform before “0.0” appears, the display will show “Err.”
• If you do not step onto the platform within 30 seconds after “0.0” appears,
the scale will automatically shut off.
• If personal data is not programmed, the scale will display “- - - -” and
automatically shut off. Please follow the instructions on page 6.
2. View your readings
Gain or loss of weight
since Day 1 with
up/down & +/- arrow
Gain or loss of weight since
previous reading with up/down
& +/- arrow
User number
Current step
Total Steps
established
% achieved in
current step
% achieved
toward total goal
Actual weight
Mode you are currently using
(Classic or Weightless)
3. Additional callouts
Jenny Craig Benefit Icon – First 5% weight loss from Day 1.
Losing 5% of your body weight is a very important achievement.
It represents an amount of weight that lowers your risk for health
conditions such as heart disease, diabetes and hypertension.
When you reach this very significant milestone, your HealthyTrack
Scale will notify you by displaying an apple icon at the top of the
screen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Reward Icon – Each completion of one step.
NOTE:
• If you remain on the platform after your weight is displayed, the power shuts
off automatically in about 20 seconds.
• If you step off the platform after your weight is displayed, the power shuts off
automatically in about 20 seconds.
Weight Only Mode
No personal data set up is necessary.
If you wish to turn the unit off before automatic shut off, press the “1/OFF”
button for three seconds or more.
1. Tap on the center of platform
The display will flash “8888” (calibrate) and then “0.0” will be displayed.
2. Step onto the platform
NOTE:
• If you step onto the platform before “0.0” appears, the display will show “Err.”
• If you do not step onto the platform within 30 seconds after “0.0” appears,
the scale will automatically shut off.
3. The display will show your weight
NOTE:
• If you remain on the platform after your weight is displayed, the power shuts
off automatically in about 20 seconds.
• If you step off the platform after your weight is displayed, the power shuts off
automatically in about 20 seconds.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
“Err” appears on the display
You stepped on the scale before “0.0” appeared on the display.
Wait until “0.0” appears, then step on the scale.
“- EE -” appears on the display
Reading cannot be obtained if the weight capacity is exceeded.
“- - - -” appears on the display
If it is during weight measuring process, there is no memory of your personal
data. Please program your personal data.
“LO” appears on the display
Lithium batteries are low. Please change the batteries immediately.
00% is shown in Goal
You over-achieved your goal. No % in Goal will be displayed.
% are displayed in Goal but nothing is in Step
This happens when the difference between your goal weight and initial
weight is less than 10 lb or 5 kg.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For technical questions about this product,
please contact Tanita at 1-800-Tanita8.
For information about Jenny Craig programs,
please contact Jenny Craig at 1-800-Jenny20
Tanita Corporation
Tanita Health Equipment H.K. Ltd.
Unit 301-303 3/F Wing On Plaza
62 Mody Road, Tsimshatsui East
Kowloon, Hong Kong
14-2, 1-Chome, Maeno-Cho
Itabashi-Ku, Tokyo, Japan 174-8630
Tel: +81(0)-3-3968-2123
Fax: +81(0)-3-3967-3766
Tel: +852 2838 7111
Fax: +852 2838 8667
ISO 9001 Certified
Tanita Europe GmbH
Dresdener Strasse 25
D-71065 Sindelfingen
Germany
Tel: +49 (0)-7031-6189-6
Fax: +49 (0)-7031-6189-71
Tanita Corporation of America
2625 South Clearbrook Drive
Arlington Heights, IL 60005 USA
Tel: +1-847-640-9241
Fax: +1-847-640-9261
(800) Tanita-8 (USA & Canada Only)
Tanita UK Ltd.
Tanita France S.A.
The Barn, Philpots Close, Yiewsley,
Middlesex, UB7 7RY UK
Tel: +44 (0) 1895 438577
Fax: +44 (0) 1895 438511
Villa Labrouste
68 Boulevard Bourdon
92200 Neuilly-Sur-Seine France
Tel: +33 (0)-1-55-24-99-99
Fax: +33 (0)-1-55-24-98-68
© 2005 Tanita Corporation
HD338 7801
Download from Www.Somanuals.com. All Manuals Search And Download.
|