D A B -5 0
Operation Manual
DAB/FM Tuner
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
ACCESSORIES
ADJUSTING THE ANTENNA
Adjusting the antenna
13
Accessories
01
02
03
OPERATION AND FUNCTIONS
CONTENTS
ON, OFF and standby
Info and function
DAB tuning
Saving and selecting channels
FM tuning
14
14
15
15
16
Contents
SAFETY PRECAUTIONS
Safety precautions
TROUBLESHOOTING
IMPORTANT SAFETY INSTRUCTIONS
Troubleshooting
17
18
Important safety instructions
IMPORTANT INFORMATION
Important information
04
06
TECHNICAL DATA
Technical data
CONNECTION
Connection to the mains
07
REMOTE CONTROL
Installation of batteries
Using the remote control
Remote control functions
08
08
09
FRONT PANEL AND CONNECTIONS
Front panel
Connections
10
11
CONNECTION
Audio connection layout
12
02
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
A triangle with a lightning symbol draws the user's attention
to "dangerous voltage" without insulation in the cabinet
which may be high enough to entail a risk of electric shock.
A triangle with an exclamation mark draws the user's
attention to important instructions for use and maintenance
in the accompanying manual, which should be studied.
A symbol for CLASS II (double insulation)
TO MINIMISE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE
THE UNIT TO RAIN OR MOISTURE. DO NOT OPEN THE CABINET AS IT
CONTAINS DANGEROUS VOLTAGE. ONLY QUALIFIED TECHNICIANS ARE
ALLOWED TO CARRY OUT REPAIR AND SERVICE.
WARNING:
CAUTION:
If the plug of the power cord needs to be replaced, it is important that the replacement
is identical to the plug to be replaced, or that the new plug has been recommended by
the manufacturer
TO AVOID ELECTRICAL SHOCK, IT IS IMPORTANT TO INSERT THE PLUG
CORRECTLY INTO THE SOCKET.
03
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: IT IS IMPORTANT THAT YOU READ AND OBSERVE BOTH THE INSTRUCTIONS IN THIS MANUAL AND
THE INSTRUCTIONS ON THE UNIT. KEEP THIS MANUAL FOR FUTURE REFERENCE.
This unit was designed and manufactured with a view to providing maximum safety for the user. Incorrect use of
the unit may cause electrical shock or fire. The protection devices built into this unit will protect the user if the
procedures below are observed in connection with installation, use and repair. This unit is fully electronic and
contains no parts that can be repaired by the user.
DO NOT REMOVE THE CABINET. RISK OF DANGEROUS VOLTAGE. ONLY QUALIFIED TECHNICIANS ARE
ALLOWED TO REPAIR THE UNIT.
Read the manual
Heat
Upon unpacking the unit,
please read the manual
carefully and observe all the
instructions given.
Do not place the unit near
sources of heat such as radiators,
heat registers, ovens or other
units that produce heat.
Power supply
Only the power supply indicated on the
rating plate must be used for this unit.
If you are not sure which power supply
you have, please contact the distributor
or the local electricity supplier.
Water and moisture
The unit must not be placed
close to water, such as bathtub,
wash basin, kitchen sink or
laundry tub, in a damp cellar or
close to a swimming pool, etc.
Cleaning
Unplug the unit before cleaning.
Do not use liquid detergents and
aerosol cleaning agents. Use a
dry cloth.
Earthing or polarisation
If the plug cannot be inserted properly into the
socket, or if the plug does not fit, the unit must not
be used in your country.
Power cords
Wiring must be organised to
prevent people from stepping on
the cables and to avoid pinching
by objects placed on or beside
them. Take special care around
sockets and plug boxes and
where the power cords leave the
unit.
Ventilation
The cabinet is provided with slots and
openings to ensure ventilation and reliable
operation and to protect the unit against
overheating. Do not block or cover these
openings. The openings must never be
blocked, for instance by placing the unit on
a bed, a sofa, a carpet or similar surface.
Overloading
Make sure that wall sockets,
extension cords and plug
boxes are not overloaded as
this may lead to fire or
electrical shock.
04
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Lightning
Damage
Unplug the unit for additional
protection during thunder or when
the unit is not used for prolonged
periods. This will prevent damage
to the unit from lightning and
power surges.
Unplug the unit and contact qualified technicians in
the following cases:
A) If the power cord or the plug is damaged.
B) If liquid has been spilled on the unit or objects
have fallen into the unit.
C) If the unit has been exposed to rain or water.
D) If the unit does not work properly after adhering to
the instructions in the operation manual. Only the
settings described in the operation manual must be
made as incorrect setting may result in damage and
often will make it difficult for a qualified technician to
make the unit work properly again.
E) If the unit has been dropped or damaged in any
other way.
F) When the operation of the unit changes
drastically, the unit requires service.
Penetration of objects and liquid
Never push any foreign objects
through the openings into the unit,
as they may touch dangerous
voltage points or short-circuit parts
and thus cause fire or electric
shock. Do not spill liquid on the
unit.
Accessories
Service
Do not place the unit on unstable surfaces such as a
trolley, stand, tripod, shelf or table. The unit
may fall and injure children or adults or
be seriously damaged. Use only trolley,
stand, tripod, shelf or table that is very
stable or provided with the unit. The unit
must be installed in accordance with the
manufacturer's instructions and by means of
installation equipment recommended by the
manufacturer.
Do not attempt to carry out any
service work yourself. By opening or
removing the cabinet, you will be
exposed to dangerous voltage or
other hazards. Any service work
should be carried out by qualified
technicians.
Spare parts
If spare parts are required, make sure that the
service technician uses spare parts specified by the
manufacturer or spare parts with the same
characteristics as the original. Unauthorised spare
parts may cause fire, electrical shock, etc.
If the unit is placed on a trolley, the trolley must be
moved very carefully. Sudden stops, unnecessary
force and uneven surfaces may cause the trolley to
turn over.
Safety check
Loads
After service or repairs on the unit,
ask the service technician to carry
out a safety check to ensure that
the unit is ready for use.
Do not place heavy loads on the
unit and do not step on it. The load
may fall and cause serious injury to
persons or damage to the unit.
05
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
Handling instructions
Condensation
Condensation may occur in the following cases:
The top and back panel of the unit may become
warm after prolonged use. This is not due to a
defect.
When the unit is moved directly from a cold to a
warm place.
Turn off the power when the unit is not used.
When the unit is used in a room where the
radiator has just been switched on or a place
where the cold air from the air-conditioning
system is directed at the unit.
Protect the power cord
If the unit is used in the summer in a warm and
humid room just after it has been moved from an
air-conditioned room.
Follow the instructions below to prevent
abnormal operation, electrical shock, fire or
personal injury:
Hold the plug firmly when inserting it into the
socket.
Avoid heat-producing devices.
Do not place objects on the power cord.
Do not carry out service work on or change the
power cord.
If there is steam or a high level of humidity in the
room.
In case of condensation, the unit will not work
properly. Turn off the unit. Unplug the unit and leave
it for 2-3 hours. The unit will then have adapted to
the environment and any condensation will have
disappeared.
Positioning
Do not place the unit in any of the fol. places:
In sunlight, close to heat-producing devices or in
an enclosed rack.
In places with high temperatures (40C or more)
or high relative humidity (90% or more).
In dirty places as some internal parts may be
damaged.
Do not put your fingers or any
other objects into the unit
Touching the internal parts is dangerous and
may cause injury or damage. Do not open the
cabinet.
Do not place any foreign matter in the unit.
Interference
Placing the unit near a television set, radio or
video player may cause poor picture and sound
quality. In that case, move the unit further away
from the television set, radio or video player.
06
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION
Connection to the mains
Stereo Output
Antenna
Contrast
Optical Output
Model: DAB-50
Power Rating 230-240 V AC~50Hz
Max Power Consumption: 30W
Item No.: 11048.01
Serial No.:
Do not turn on the power before all connections have been made correctly.
Check that all connections have been made correctly before turning on the
power.
Check that the mains voltage is 230-240V AC50Hz before turning on the
power.
Connection to the mains
Check that all other connections have been made correctly before inserting the mains plug into the wall
socket.
Then insert the plug into a suitable socket.
If the unit is to be used abroad, you may need an adapter.
07
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
Installation of batteries
Remove the cover as illustrated.
Replace the cover.
Position two batteries of the type
AAA/R03/UM4 in the battery
compartment. Make sure that the
orientation of the batteries is correct (see
drawing at bottom).
Do not mix new and old batteries and do not use different types of batteries.
If the remote control is not used for prolonged periods, remove the batteries from the remote control
to avoid corrosion.
Using the remote control
CONTROL/TUNING
Direct the remote control at the sensor on the front
panel of the unit. When the remote control signal is
received, the unit reacts accordingly. The remote
control works within a range of 6 metres.
POWER
1
2
3
4
DAB/FM
AUTOTUNE
INFO
PRESS TO SELECT
DAB-50 DAB/FM-TUNER
+
+
Sometimes the remote control does not work well in strong light. You may have to move the unit if it is a
problem.
Malfunction may occur if other remote controls are used near the unit.
Do not place any objects on the remote control, as the batteries may become flat if a key is depressed
constantly.
Make sure that there are no obstacles between remote control and unit.
Do not position the unit behind tinted glass as it may reduce the maximum range of the remote control.
08
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
Remote control functions
DAB-50 FUNCTIONS:
Scroll +/-: Switches between DAB and FM
stations.
Select: Switches between MONO and
AUTO on the FM band, and selects the
DAB station displayed.
+
1-4 : Selects stored stations. If depressed
for more than 2 seconds, a station is stored
under the number concerned.
Power: Sets the DAB-50 in standby mode.
Autotune: Press once to automatic tune in
to DAB stations. Depress button for 2
seconds to initiate an international search.
At FM, the autotune function will search for
a station at a higher frequency.
Info: Displays RDS and DAB information.
Function: Switches between DAB and FM.
CDP-50 FUNCTIONS:
Eject: Opens the CD tray.
Program: Allows playback of the music
tracks on a CD in a certain order.
Stop: Stops playback.
Previous: Selects the previous track.
Depress button to rewind.
Play/Pause: Starts and pauses playback.
Repeat: Repeats a single track or all tracks
on a CD.
Power: Sets the CDP-50 in standby mode.
Next: Selects the next track. Depress
button for fast forward.
+
Random: All tracks are played in random
order.
AMP-50 FUNCTIONS
Input buttons: Selects input of amplifier.
Treble: Adjusts treble level by means of
VOL + and -.
Bass: Adjusts bass level by means of VOL
+ and -.
Power: Sets the AMP-50 in standby mode.
Volume+/-: Adjusts the master volume.
Some of the functions of the unit can only be performed by means of the remote control. Some functions are
connected with the selected signal input source. Some buttons on the remote control may therefore not be
available if the corresponding signal input source has not been selected.
09
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL AND CONNECTIONS
Front panel
CONTROL/TUNING
POWER
1
2
3
4
DAB/FM
AUTOTUNE
INFO
PRESS TO SELECT
DAB-50 DAB/FM-TUNER
1
2
Mains switch: Used to interrupt the mains voltage.
LED indicator: Lights green when the unit is turned on. Lights red when the unit is in
standby mode or in operation.
3
Preset no. 1: Selects the station saved under no. 1. If the button is depressed for
more than two seconds, a station is saved under the current number.
Preset no. 2: Selects the station saved under no. 2. If the button is depressed for
more than two seconds, a station is saved under the current number.
Preset no. 3: Selects the station saved under no. 3. If the button is depressed for
more than two seconds, a station is saved under the current number.
Preset no. 4: Selects the station saved under no. 4. If the button is depressed for
more than two seconds, a station is saved under the current number.
DAB/FM: Switches between DAB and FM.
Autotune: Press once to automatic tune in to DAB stations. Depress the button for
two seconds to initiate an international search. At FM, the autotune function will search
for a station at a higher frequency.
Info: Switches between RDS and DAB information (program information, time and
date, signal strength, etc.).
4
5
6
7
8
9
10 Adjusting button: Used to switch between the tuned in DAB stations. Manual tuner in
FM mode.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL AND CONNECTIONS
Connections
Stereo Output
Antenna
Contrast
Optical Output
Model: DAB-50
Power Rating 230-240 V AC~50Hz
Max Power Consumption: 30W
Item No.: 11048.01
Serial No.:
1
2
3
4
5
1
2
Stereo Output: Analogue stereo output. For connection to stereo amplifier or receiver
with analogue input.
Optical Output: Optical SPDIF output. For connection to stereo amplifier or receiver
with digital input.
Antenna: For connection of the supplied antenna or for the communal antenna system.
Contrast: For adjustment of display contrast.
AC input: For connection of mains voltage. Make sure that the plug has been correctly
inserted, and that the voltage corresponds to the text printed on the back panel of the
cabinet.
3
4
5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION
Audio connection layout
Stereo Output
Antenna
Contrast
Optical Output
Model: DAB-50
Power Rating 230-240 V AC~50Hz
Max Power Consumption: 30W
Item No.: 11048.01
Serial No.:
Digital amplifier/receiver
VOLUME
POWER
HEADPHONE
PHO
TUNER
DVD
CD
AUX
1
AUX
2
FUNCTION
AMP-50 AMPLIFIER
Subwoofer
(Optional)
Analog amplifier/receiver
VOLUME
POWER
HEADPHONE
PHO
TUNER
DVD
CD
AUX
1
AUX
2
FUNCTION
AMP-50 AMPLIFIER
This page only contains suggestions for connection of your Eltax DAB-50. Note that the
accessories in the pictures on this page are not included in the supply.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE ANTENNA
Adjusting the antenna
As it applies to all other radios, the sound quality depends on the signal strength of the antenna
inputs.
The position of the radio in relation to the transmitter thus directly influences the quality of the signal
received. For an optimal result it is therefore very important that you make sure that the radio receives
the best possible antenna signal.
It is possible to insert a bar in the display which will
indicate the strength of the antenna signal. If you wish
to have such a bar displayed, you must press the INFO
button when you have tuned in to a station on the FM
band.
DR P3
ooooooooooooooo
The signal strength is displayed through the length of
the bar. The longer the bar, the stronger the signal.
The fifth square of the bar has not been filled in like the
remaining ones. It indicates the minimum signal
strength required if an acceptable result is to be
achieved.
2
3
4
DAB/FM
AUTOTUNE
INFO
The supplied antenna must be
adjusted for the best possible result
by means of the signal bar
Antenna
Contrast
Optical Output
described above.
A good tip is to let the antenna
ends point in the vertical direction
and fix them on a wall.
For an optimal result it is recommended to
install a DAB antenna on the roof or on the
loft.
Antenna
Contrast
Optical Output
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND FUNCTIONS
On, Off and standby
1
2
Turn on the unit by pressing the mains switch.
Press the standby button on the remote control to switch to standby
mode. The display will turn off and all functions will be reduced to a
minimum to make sure that the unit uses minimal power. When in standby
mode the unit only reacts to the standby button of the remote control.
If you wish to turn off the unit to avoid any power consumption, you must
press the mains switch.
3
+
2
POWER
1
PHON
3
DAB-50 DAB/FM TUNER
Protect the environment and turn off the unit after use.
Info and function
1
2
As this tuner can receive both normal FM radio
and DAB (Digital Audio Broadcasting), it features
a function that can switch between the two
reception types. To switch between DAB and FM,
you must either press the DAB/FM button on the
front panel or the FUNCTION button on the
remote control.
CONTROL/TUNING
1
2
3
4
DAB/FM
AUTOTUNE
INFO
PRESS TO SELECT
1
2
This tuner features RDS on the FM receiver. DAB
also offers some information possibilities that
resemble RDS as we know it from FM. To activate
this information from both DAB and FM, you must
press the INFO button either on the front panel or
on the remote control. The display will show
information about for instance time and date,
name of station, name of artist, title, etc.
+
Note:
If the INFO button is pressed after channels have
been saved, the strength of the antenna signal will
also be displayed.
2
1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND FUNCTIONS
DAB tuning
When the unit is turned on for the first time, all settings will be default settings. The settings can be
changed according to your preference. When the unit is turned off the next time, these settings will
naturally be saved as the new default settings. This also applies if you unplug the unit.
CONTROL/TUNING
When the unit has been turned on, channels
must be saved. This is done by means of the
autotune function.
1
2
3
4
DAB/FM
AUTOTUNE
INFO
1
PRESS TO SELECT
1 To use the autotune function through the front
panel controls, press the AUTOTUNE button
for two seconds. An international search will
be initiated.
+
You can also press the AUTOTUNE button on
the remote control for two seconds.
2
2
Note:
If the button is only pressed once, the unit will
once again search for the channels already
found.
The message SEARCHING will be shown at the
bottom of the display, and you will see a bar at the
top of the display that grows longer indicating how
far the tuning process has come. As it finds
channels, you will see a figure at the top line to
the right of the display that shows how many
channels have been found.
00000
Searching
1
2
3
4
DAB/FM
AUTOTUNE
INFO
If no channels are found, you must check if the
antenna has been correctly connected. You can
do this by tuning in on a channel through manual
tuning on the FM band, and then press the INFO
button to display the signal bar and check the
signal strength (see the section on FM tuning)
000000000000000
searching
10
1
2
3
4
DAB/FM
AUTOTUNE
INFO
Saving and selecting channels
CONTROL/TUNING
1 If you want to save a channel under one of the
four presets, you must press down the button with
the number concerned for two seconds. When the
2
1
2
3
4
DAB/FM
AUTOTUNE
INFO
channel has been saved and you wish to listen to
that channel, press the button with the number
that you have saved the channel under. The
procedure is the same for both FM and DAB.
1
PRESS TO SELECT
2
+
Channels that have not been saved can be
selected either by means of the SCROLL buttons
on the remote control or the CONTROL/TUNING
button on the front panel. Note that if the channel
is selected by means of the CONTROL/TUNING
button, you must confirm your choice by pressing
the adjusting button. This function can be
deactivated by pressing the button for two
seconds.
2
1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND FUNCTIONS
FM tuning
The DAB-50 offers both manual and automatic tuning on the FM band.
This makes it possible to save just one specific channel. It also makes it possible to adjust the supplied
antenna for the best possible signal.
Automatic tuning
CONTROL/TUNING
1
To use the autotune function through the front
panel controls, you must press the
AUTOTUNE button. The unit will search for a
frequency with a proper signal.
2
3
4
DAB/FM
AUTOTUNE
INFO
1
PRESS TO SELECT
2 You can also activate the autotune function
through the remote control.
+
2
The display will now use a higher frequency. At the
top of the display you can see that the frequency
increases. When the tuner has found a channel,
the tuning process will automatically stop. The
sound from the channel found will be heard and
any RDS information will be displayed.
If no channels are found, you must check if the
antenna has been correctly connected. You can do
this by tuning in on a channel through manual
tuning on the FM band, and then press the INFO
button to display the signal bar and check the
signal strength (see the section on manual FM
tuning).
1
2
3
4
DAB/FM
AUTOTUNE
INFO
Manual tuning
To activate the manual tuning function
through the front panel controls, simply turn
the CONTROL/TUNING button. If you turn it
clockwise, the unit will tune in to a station at
a higher frequency and if you turn the button
anti-clockwise, the unit will tune in to a
station at a lower frequency. It is also
possible to activate the manual tuning
function through the remote control. Use the
SCROLL + and SCROLL - buttons that
works in the same manner as the
1
CONTROL/TUNING
1
1
2
3
4
DAB/FM
AUTOTUNE
INFO
PRESS TO SELECT
2
+
2
CONTROL/TUNING button on the front
panel.
Note:
If there are channels from the FM band that
have not been saved, you must tune in to
them again either manually or automatically
if you wish to listen to them again.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Troubleshooting
PROBLEM
CAUSE/REMEDY
No power when the unit is turned on. - Switch on the electric current at the socket.
- Check that the plug has been correctly inserted into the
socket.
- The internal fuse has blown and must be replaced by a
qualified service technician.
- The power cord has been damaged and must be
replaced.
No sound.
- The unit has not been turned on.
- Incorrect connection to the amplifier.
- No loudspeakers have been connected to the amplifier.
- The DAB-50 has not found any stations on DAB.
The display does not show DAB/RDS - The DAB-50 has not found any stations on DAB/FM.
information.
- The selected station does not broadcast any information.
- The antenna signal is too poor. See the section on
adjusting the antenna.
I cannot hear the station selected
- You have not pressed the CONTROL/TUNING button
after selection. The station that you listen to will be
described in the top line of the display. When you "scroll"
through the channels by means of the CONTROL/TUNING
button, you must always remember to press the
CONTROL/TUNING button once to confirm your choice.
I can hear “tick/blob” sounds at
some of the stations.
- Like all other digital media DAB is reproduced in a
very high sound quality. But if the antenna signal is too
weak, you will not hear any whistling but instead you will
hear blackouts or "tick/blob" sounds. You must therefore
check if the antenna signal is strong enough. See the
section on adjusting the antenna.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
RF section:
Tuner bands
DAB
FM
174-240MHz (Band III)
87.5-108.0MHz
Sensitivity
Display:
-96dBm type
2 lines of 16 characters
LED backlight
Presets
4
Audio outputs
Stereo, 2.5Vpp
48kHz sample rate
16 bit sample resolution
Optical SPDIF output
IEC60958 Compliant
48kHz sample rate
24 bit sample resolution
Voltage and power consumption
Dimensions (WxDxH)
Weight
See back panel
430 x 290 x 75mm
4.5 kg
We reserve the right to change the technical data and the design of the product without notice as a result of
further development.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
www.tangent-audio.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|