Symphonic TV DVD Combo SC520FDF User Manual

OWNER’S

MANUAL

COLOR TV/DVD

(20 inch)

SC520FDF

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-242-7158.

Or visit our WEB SITE at http://www.Symphonic.us

Please read before using this equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13. Outdoor Antenna grounding - If an outside antenna or

cable system is connected to the unit, be sure the anten-

na or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect

to proper grounding of the mast and supporting struc-

ture, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrode.

(Fig. A)

19. Damage Requiring Service - Unplug this unit from the

wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or

frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified techni-

cian to restore the unit to its normal operation.

14. Lightning - For added protection for this unit receiver

during a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable system.

This will prevent damage to the unit due to lightning and

power-line surges.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

15. Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact

with them might be fatal.

20. Replacement Parts - When replacement parts are

required, be sure the service technician has used replace-

ment parts specified by the manufacturer that have the

same characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, injury to

persons or other hazards.

21. Safety Check - pon completion of any service or repairs

to this unit, ask the service technician to perform routine

safety checks to determine that the unit is in proper

operating condition.

16. Overloading - Do not overload wall outlets and exten-

sion cords as this can result in a risk of fire or electric

shock.

17. Object and Liquid Entry - Never push objects of any

kind into this unit through openings as they may touch

dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the unit.

22. Heat - This unit product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18. Servicing - Do not attempt to service this unit yourself

as opening or removing covers may expose you to dan-

gerous voltage or other hazards. Refer all servicing to

qualified service personnel.

- 3 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision. Reverse engineering or dis-

assembly is prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This Class B digital apparatus complies with

Canadian ICES-003.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or inciner-

ated but disposed of in accordance with your local

regulations concerning chemical wastes.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a unit which has

moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the unit on and allow at least 2 hours for the

unit to dry out.

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the unit near strong magnetic fields.

Avoid moving the unit to locations where tempera-

•

: Description refers to TV operation (in the TV mode).

ture differences are extreme.

DVD-V

Be sure to remove disc and unplug the AC power

cord from the outlet before carrying the unit.

•

: Description refers to playback of DVD video discs

(in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to playback of Audio CDs

(in the DVD mode).

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

QUICK

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

•

Do not put your fingers or objects into the unit disc

loading tray.

•

Do not place anything directly on top of the unit.

•

SUPPLIED ACCESSORIES

Remote Control Unit

Batteries

Owner’s Manual

Owner's Manual

( NE207UD )

2 AA Batteries

( 1EMN20326 )

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

•

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

DVD SECTION

C IMPORTANT SAFEGUARDS . . . . .2

C CHANGING THE DVD SET UP

ITEMS . . . . . . . . . . . . . . . . . . . . . . .26

C PRECAUTIONS . . . . . . . . . . . . . . . .4

C ABOUT THE DISCS . . . . . . . . . . . .19

PLAYABLE DISCS . . . . . . . . . . . .19

UNPLAYABLE DISCS . . . . . . . . . .19

CUSTOM MENU . . . . . . . . . . . . . .26

LANGUAGE SETTING . . . . . . . .26

DISPLAY SETTING . . . . . . . . . .27

AUDIO SETTING . . . . . . . . . . . .27

PARENTAL CONTROL . . . . . . . .28

OTHER SETTINGS . . . . . . . . . . .28

INITIALIZE . . . . . . . . . . . . . . . . . .28

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

C PLAYING A DISC . . . . . . . . . . . . . .20

BASIC PLAYBACK . . . . . . . . . . . .20

GENERAL FEATURES . . . . . . . . .20

DISC MENU . . . . . . . . . . . . . . . . .20

TITLE MENU . . . . . . . . . . . . . . . . .20

RESUME . . . . . . . . . . . . . . . . . . . .21

PAUSE . . . . . . . . . . . . . . . . . . . . . .21

STEP BY STEP PLAYBACK . . . . .21

WARNING . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C SUPPLIED ACCESSORIES . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C TROUBLESHOOTING GUIDE . . .29

C MAINTENANCE . . . . . . . . . . . . . . .32

DISC HANDLING . . . . . . . . . . . . .32

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .8

C SPECIFICATIONS . . . . . . . . . . . . .33

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .34

C WARRANTY . . . . . . . . . . .Back Cover

FAST FORWARD /

FAST REVERSE . . . . . . . . . . . . . .21

C PREPARATION FOR USE . . . . . . .10

SLOW FORWARD /

SLOW REVERSE . . . . . . . . . . . . . .21

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .10

ZOOM . . . . . . . . . . . . . . . . . . . . . .21

CONNECTING TO FRONT A/V

C SEARCH FUNCTION . . . . . . . . . . .22

TRACK SEARCH . . . . . . . . . . . . .22

TITLE / CHAPTER SEARCH . . . .22

TIME SEARCH . . . . . . . . . . . . . . .22

MARKER SETUP SCREEN . . . . . .22

INPUT JACKS . . . . . . . . . . . . . . . .11

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS (for DVD)11

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .12

INSTALLING THE BATTERIES . .12

SPECIAL PLAYBACK FUNCTION . .23

REPEAT . . . . . . . . . . . . . . . . . . . . .23

PROGRAM . . . . . . . . . . . . . . . . . . .23

RANDOM PLAYBACK . . . . . . . . .23

TV SECTION

C TV OPERATION AND SETTINGS .13

WATCHING A TV PROGRAM . . .13

DEGAUSSING . . . . . . . . . . . . . . . .13

PICTURE CONTROL . . . . . . . . . . .13

SLEEP TIMER . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . .14

CHANNEL SET UP . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . .16

TV RATING SET UP . . . . . . . . .16

MPAA RATING SET UP . . . . . .17

CHANGE ACCESS CODE . . . . .17

MENU LANGUAGE . . . . . . . . . . .17

C CHANGING THE SETTINGS . . . .24

SUBTITLE LANGUAGE . . . . . . . .24

AUDIO LANGUAGE . . . . . . . . . . .24

STEREO SOUND MODE . . . . . . . .24

CAMERA ANGLE . . . . . . . . . . . . .24

BLACK LEVEL SETTING . . . . . . .24

VIRTUAL SURROUND . . . . . . . . .25

THE ON-SCREEN INFORMATION . .25

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .18

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV Mode

Infrared remote control

Trilingual on screen TV setup display selectable

in English, Spanish or French

181 channel capability PLL frequency synthesiz-

er tuner with direct station call (A converter may

be necessary to view scrambled cable channels.)

Closed Caption Decoder – You may view special-

ly labeled (cc) TV programs, movies, news, etc.

with either a dialogue caption or text display added

to the program.

Auto power off system – If there is no air signal

•

input from the antenna terminal and no operation

for 15 minutes, the unit will turn itself off automat-

ically.

Sleep timer – Allows you to have the unit auto-

matically turn off at a desired time.

•

V-CHIP – Enables parents to prevent their children

from watching inappropriate material on TV.

•

DVD Mode

¡Dolby Digital sound

¡Parental lock

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD or Audio CD.

¡Still/fast/slow/step playback

Various playback modes are available including

still pictures, fast forward/reverse, slow motion and

step frames.

¡On-screen display

Information about the current operation can be

displayed on a TV screen, allowing you to confirm

the currently active functions (such as program

playback), on the TV screen using the remote

control.

¡Random playback for Audio CD

This unit can shuffle the order of tracks to play

them in random order.

¡Program playback for Audio CD

You can program the order of tracks to play them in

any desired order.

¡Search

Chapter search / Title search / Track search / Time

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Repeat

Chapter / Title / Track / All / A-B

¡Zoom

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no

input from the unit for 5 minutes in the stop mode.

After the screen saver program is activated for 15

minutes, the power automatically turns off.

Magnified screen can be displayed.

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Virtual Surround

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Choices for audio language and sound mode

You can select the desired audio language and

sound mode, if different languages and modes are

available on a disc.

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL - [Fig.1]

OPEN/

POWER

VOLUME

CHANNEL

STOP

SKIP

PLAY

SKIP

PAUSE CLOSE

VIDEO

L–AUDIO–R

–SEARCH–

HEADPHONE

7 8 9 10 9 1112 13

7.Remote sensor window

8.STOP C Button [P.20]

Stops operation of the disc.

[Fig. 2]

- REMOTE CONTROL -

9.SKIP H / G Buttons [P.22]

Press once to skip chapters or tracks to a desired

point.

OPEN/

POWER PICTURE SELECT

Buttons (Front panel) [P.21]

Press and hold to change forward or reverse

playback speed.

CH.

10. PLAY B Button [P.20]

SLEEP

+100

Starts playback of the disc.

VOL.

11. PAUSE F Button [P.21]

Pauses the current disc operation.

12. OPEN/CLOSE A Button [P.20]

Hit to insert a disc into or remove it from the

tray.

+10

SKIP

ZOOM

MUTE

PLAY

STOP

REV

FWD

13. HEADPHONE Jack

DISC

To connect headphone (not supplied) for personal

listening.

PAUSE SLOW

DISPLAY

14. PICTURE Button [P.13]

ENTER

Hit to adjust the picture.

SETUP

TITLE

RETURN

15. Number Buttons

CLEAR SEARCH MODE REPEAT

A-B

TV Mode: [P.13]

Press two digits to directly access the desired

channel.

Remember to hit [0] before a single digit channel.

+100 Button–

Hit to select cable channels which are higher

than 99.

DVD Mode: [P.22]

Hit to enter the desired number.

+10 Button–

Hit to enter the desired numbers which are higher

than 9.

AUDIO SUBTITLE ANGLE

MODE

1.Disc loading tray

2.VIDEO input Jack

Connect to the video output jack of a video camera or

VCR.

3.AUDIO L/R input Jacks

Connect to the audio output jacks of a video camera or

VCR.

16. SLEEP Button [P.14]

Sets the Sleep Timer.

4.POWER Button [P.13]

17. DISPLAY Button

Hit to turn the power on and off.

Buttons [P.13]

Press to control the volume level for the DVD and TV.

Buttons [P.13]

Press to select memorized channels.

TV Mode:

5.VOLUME (VOL.)

Displays the current channel number on the TV

screen.

DVD Mode: [P.25]

6.CHANNEL (CH.)

Displays the current status on the TV screen.

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR PANEL - [Fig.3]

ANT.

COAXIAL

36 37

18. SETUP Button [P.26]

{

30.

Buttons

Hit to enter or exit the setup menu of TV or DVD.

TV Mode: [P.13]

Press to select a setting mode from the menu on

19. TITLE Button [P.20]

the TV screen.

Displays the title menu.

Press to select or adjust from a particular menu.

DVD Mode: [P.20]

Press to select a menu item.

20. CLEAR Button [P.22]

Hit to clear or cancel a setting currently entered.

21. MODE Button [P.23, 24, 25]

31. DISC MENU Button [P.20]

Hit to call up the program screen or the random

screen in the stop mode.

Calls up the DVD menu.

32. REV

Button [P.21]

Hit to call up the Black Level Setting screen or

the Virtual Surround screen during playback.

Hit to view the DVD picture in fast reverse or

slow reverse motion.

22. SEARCH MODE Button [P.22]

FWD

Button [P.21]

Hit to locate a desired point.

Hit to view in fast or slow forward motion.

23. AUDIO Button [P.24]

33. ZOOM Button [P.21]

Hit to select a desired audio language or sound

mode.

Enlarges part of a DVD-reproduced image.

34. MUTE Button [P.13]

24. SUBTITLE Button [P.24]

Mutes the sound. Hit it again to restore sound.

Hit to select a desired subtitle language.

35. SELECT Button [P.11]

25. REPEAT Button [P.23]

Hit to change to TV mode, external input mode or

DVD mode.

Repeats playback of the current disc, title, chap-

ter, or track.

36. COAXIAL Jack [P.11]

26. ANGLE Button [P.24]

Connect to the digital input of an external

amplifier or decoder (for DVD Audio only).

Hit to change the camera angle to see the

sequence being played back from a different angle

(if available).

37. ANT(ENNA). Jack [P.10]

Connect to an antenna, cable system or satellite

system.

27. A-B Button [P.23]

Repeats playback of a selected section.

38. Power cord [P.13]

28. RETURN Button [P.22]

Connect to a standard AC outlet (120V/60Hz).

Returns to the previous screen in the setup menu.

NOTE:

29. ENTER Button [P.15]

Remove the power cord from the hook to avoid

breaking a wire before you connect to a standard

AC outlet.

•

Hit to accept a setting.

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

Plug the incoming cable into the ANT. jack on the rear of the unit.

If your cable service supplies you with a converter box or if you use a

satellite system, connect the box with this unit as shown below.

Cable

TV signal

Antenna

Incoming cable from home Antenna /

Cable Company (No Cable Box)

ANT.

COAXIAL

Rear of the unit

ANT.

Cable Box or

Satellite Box*

OUT

[Fig. 4]

Incoming cable from Cable Company

or Satellite Antenna

*NOTE (DO NOT DISCONNECT FROM BOX)

Some cable TV systems use scrambled signals and

require a special converter to receive these channels.

Consult your local cable company.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

Bent pin

NOTE:

Before plugging the antenna into the ANT. jack of the unit, check that the pin is

not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the

ANT. jack of the unit.

Cable

Plug

(Needs to be

straightened)

(Straight pin)

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO FRONT A/V INPUT JACKS

When you watch a program recorded on another source (VCR or video camera), use the

AUDIO/VIDEO input jacks on the front of the unit.

AUX

Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO

jacks of this unit.

Then press [SELECT] or [CH.

] until “AUX” appears on the screen.

OPEN/

POWER

VOLUME

CHANNEL

STOP

SKIP

PLAY

SKIP

PAUSE

VIDEO

L–AUDIO–R

–SEARCH–

HEADPHONE

ex.

VCR or video camera, etc.

To the Audio output jacks

Audio Cable

(commercially available)

(IN)

(OUT)

VIDEO

L–AUDIO–R

[Front of the unit]

To the Video output jack

Video Cable

(commercially available)

(IN)

[Fig. 5]

NOTE:

When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R

channel equally.

•

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

ANT.

COAXIAL

ex.

MD deck, DAT deck, etc.

To COAXIAL jack

(Only DVD AUDIO OUT)

(OUT)

To Coaxial digital

Audio input jack

Audio coaxial digital cable

(commercially available)

[Fig. 6]

(IN)

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-

tings may generate noise distortion and may also damage the speakers. (Refer to page 27.)

•

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its COAXIAL jack. By hooking the unit up to a Dolby Digital decoder,

you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as

enjoyed in movie theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

Center

speaker

ANT.

COAXIAL

Front speaker

(left)

Front speaker

(right)

To COAXIAL jack

(Only DVD AUDIO OUT)

(OUT)

Dolby Digital

decoder

To Coaxial digital

Audio input jack

Audio Coaxial digital cable

(commercially available)

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

(IN)

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the

setup mode. (Refer to page 27.)

•

Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the

setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the

speakers. (Refer to page 27.)

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

[BATTERY PRECAUTIONS]

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

3)Replace the cover.

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

•

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TV SECTION

TV OPERATION AND SETTINGS

WATCHING A TV PROGRAM

DEGAUSSING

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color

errors are seen in some locations on the screen,

please unplug the TV for approximately 30 min-

utes. When the TV is plugged back in, the degauss-

ing circuit will operate once to clear them up. Repeat

this procedure any time the TV screen is accidentally

magnetized or when the TV is moved or relocated.

1 Plug in the unit power cord

Plug the unit power cord into a standard

AC outlet.

NOTE:

If any digits appear in the corner of the

•

screen, hit [POWER] without unplug-

ging the power cord.

2 Turn on the unit

Hit [POWER] to turn on the unit.

PICTURE CONTROL

3 Select the channel number

Press [CH.

] or the Number buttons to select

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

your desired channel number.

Notes for using the Number buttons:

¡You must precede single-digit channel numbers

with a zero (for example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

Make sure ...

The unit must be turned on.

•

1 Call up the menu

4 Adjust sound

Hit [PICTURE].

Press [VOL.

] to adjust the

volume.

2 Select item you want to adjust

VOLUME 20

Hit [MUTE] to instantly mute the

sound.

Hit it again to restore the previous sound level.

Press [

] until desired control is displayed.

BRIGHT

CONTRAST

COLOR

NOTE:

BRIGHT

TINT

SHARPNESS

If you press [CH.

] in the DVD mode, you

•

–

P +

can change the TV channels. Even if you turn off

the unit in the DVD mode, when you turn it on

again, it will go into the TV mode.

3 Adjust the setting

Press

]

to adjust to your desired level within 5

TO WATCH CABLE OR SATELLITE

CHANNEL

seconds.

to decrease

brightness

to decrease

contrast

If the unit is connected to a cable box or satellite

•

BRIGHT

to increase

brightness

to increase

contrast

box, press [CH.

] to select CH3 or CH4

according to the output channel setting of the

device and select desired channel on that device.

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

TO WATCH EXTERNAL INPUT

to purple

to green

to clear

When an external equipment is connected to the

•

front AUDIO/VIDEO input jacks, press

[SELECT] or [CH.

] repeatedly until “AUX”

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

appears on the screen.

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

If the unit displays a black box on

the TV screen, this means that the

unit is set to the TEXT mode. To

clear screen, select [CAPTION1],

[CAPTION2] or [OFF].

•

SLEEP TIMER

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

Make sure ...

The unit must be turned on.

•

1 Call up the Sleep Timer Setting

Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.

1 Select “CAPTION”

Hit [SETUP].

- TV SETUP -

2 Set sleep time

Hit [SLEEP] repeatedly until your

desired sleep time appears.

CHANNEL SET UP

V-CHIP SET UP

Press [

] to point to

LANGUAGE [ENGLISH]

CAPTION [OFF]

“CAPTION”.

Each additional press will increase

the time by 30 minutes up to 120

SLEEP 120 MINUTE

minutes.

2 Select your desired caption mode

Hit [ENTER] repeatedly until your

desired caption menu appears.

After 5 seconds, the Sleep Timer setting will disap-

pear automatically.

- TV SETUP -

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

TO CANCEL THE SLEEP TIMER

Hit [SLEEP] to call up the Sleep Timer Setting. Hit

[SLEEP] repeatedly until “SLEEP 0 MINUTE”

appears.

3 Exit the caption setting mode

Hit [SETUP] to exit the menu.

NOTE:

CLOSED CAPTION SYSTEM

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Then hit [SETUP] to return to TV mode.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is

usually used for a second language if available.

NOTES:

Not all programs are broadcast with closed cap-

•

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality signals

are likely to result in caption errors or no captions

at all. Common signal conditions which may cause

caption errors are listed below:

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

CHANNEL SET UP

Make sure ...

The unit must be turned on.

•

AUTO CHANNEL PROGRAMMING

1 Select “CHANNEL SET UP”

- TV SETUP -

Hit [SETUP].

As the initial setting, this unit has memorized all

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

]

Press

[

to point to “CHAN-

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

NEL SET UP”, then hit [ENTER].

- TV SETUP -

1 Select “CHANNEL SET UP”

2 Select “ADD/DELETE CH”

– CHANNEL SET UP –

Hit [SETUP].

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press [

] to point to

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

]

Press

[

to point to

“ADD/DELETE CH”, then hit

[ENTER].

“CHANNEL SET UP”, then hit

[ENTER].

2 Begin channel scanning

3 Enter the desired channel number

– CHANNEL SET UP –

]

Press

[

to point to “AUTO

Press [CH.

] or the Number

ADD / DELETE CH (CATV)

B AUTO CH PROGRAMMING

CH PROGRAMMING”, then hit

[ENTER].

The tuner scans and memorizes all

the active channels in your area.

buttons until your desired channel

number appears. (You can also

press [

] to enter it.)

ADD / DELETE

You must precede single-digit

channel numbers with a zero

(Example: 02 ... 09).

•

(Example: CH8)

3 After scanning

The tuner stops on the lowest memorized channel.

NOTES:

When “AUTO CH PROGRAM-

MING” is activated where there

is no TV signal input, “NO TV

SIGNALS” will appear on the

display after the completion of

channel scanning.

When selecting cable channels which are higher

than 99, hit [+100] first, then press the last two

digits. (Example: to select channel 125, first hit

[+100] then hit [2] and [5].)

•

NO TV SIGNALS

4 Delete (or add) it from (or into) memory

Hit [ENTER]. The channel number changes to light

red. The channel is deleted from memory.

The unit may recognize CATV channels to be TV

To delete another channel, repeat steps 3 to 4.

If you hit [ENTER] again, the channel is memo-

rized again.

•

channels if reception condition is poor. In this case,

check the antenna connection and try “AUTO CH

PROGRAMMING” again when reception condi-

tions are better.

Added channel : Light blue

Deleted channel : Light red

Channel memory programming is NOT neces-

•

sary when connected to a cable box or satellite

box. Just select the channel for cable box or

satellite input (ex. CH3) on the unit, then select

your desired channel on the cable box or satel-

lite box.

5 Exit the channel setup mode

Hit [SETUP] to exit the menu.

NOTE:

To confirm that channel(s) has been deleted or

•

added, press [CH.

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

V-CHIP SET UP

When you select a rating and set

•

it to [BLOCK], the higher ratings

will be blocked automatically.

The lower ratings will be avail-

able for viewing.

TV–Y

TV–Y7

TV–G

TV–PG (DLSV )

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

[BLOCK]

(

)

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked,

“PROTECTED PROGRAM by ...” message appears

on the TV screen.

When you set the lowest rating to

[VIEW], all other ratings will automatically be

available for viewing.

•

V-CHIP SET UP

5 Setting “Sub-Ratings”

Make sure ...

TV–Y

[VIEW]

When you select the ratings of

TV–Y7

TV–G

(

)

The unit must be turned on.

•

TV-Y7, TV-PG, TV-14 or TV-MA

you will have the option of setting

sub rating categories.

TV–PG (

)

TV–14

(

TV–MA(

1 Select “V-CHIP SET UP”

Hit [SETUP].

- TV SETUP -

Press [

] to select a rating with

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

sub-ratings you wish to block, then

TV–Y7

[BLOCK]

Press [

] to select “V-CHIP

hit [ENTER] twice.

SET UP”, then hit [ENTER].

Press [

] to select a sub-rating,

then hit [ENTER] to set it to

[BLOCK] or [VIEW].

2 Enter Access code

Press the Number buttons to

enter the access code.

TV–PG

[BLOCK]

ACCESS CODE

For the first time set-up or in the

event the unit has lost power,

enter the default code of 0000.

•

Selection

TV-Y7

Rating Category Explanations

Fantasy Violence

3 Select the desired item

TV-PG, TV-14, TV-MA

Press [

] to select “TV RATING”, “MPAA RAT-

Suggestive Dialog (TV-PG, TV-14 only)

Coarse Language

Sexual Situation

Violence

ING” or “CHANGE CODE”, then hit [ENTER].

Refer to the pages below to set up each item.

– V-CHIP SET UP –

P 16 Step

P 17 Step

B TV RATING

MPAA RATING

CHANGE CODE

NOTE:

The blocked sub-ratings will

appear next to the rating category

in the “TV RATING” menu.

P 17 Step

•

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK]

TV RATING SET UP

Follow steps to in the “V-CHIP SET UP” section

above.

6 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

4 Blocking TV programs

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

Press [

] to select a rating that

NOTE:

(

)

you wish to block.

Hit [ENTER] repeatedly to set it to

[BLOCK] or [VIEW].

)

To change the rating, the TV must

•

(

PROTECTED PROGRAM

by TV-Y

be turned to an unprotected pro-

gram. If “PROTECTED PRO-

GRAM by ...” appears on the

screen, please change the channel

to a station that is not protected.

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested

Unsuitable for children under 14

TV-MA Mature audience only

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU LANGUAGE

MPAA RATING SET UP

Follow steps to in the “V-CHIP SET UP” sec-

tion on page 16.

- TV SETUP -

1 Select “LANGUAGE”

Hit [SETUP].

4 Select your desired item

[VIEW]

CHANNEL SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Press [

] to point to your

[VIEW]

PG–13

NC–17

[VIEW]

Press [

] to point to

[BLOCK]

desired item, then hit [ENTER] to

select [BLOCK] or [VIEW].

“LANGUAGE”.

Selection

PG-13

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Hit [ENTER] repeatedly to select “ENGLISH”,

“ESPAÑOL”= Spanish or “FRANÇAIS”= French.

3 Exit the Language mode

Hit [SETUP] to exit the menu.

NC-17

Mature audience only

NOTES:

This function effects only the language on the

screen menu and not the audio source.

•

When you select a rating and set it to [BLOCK],

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

When you set the lowest rating to [VIEW], all

other ratings will automatically be available for

viewing.

•

If for some reason the menu is in Spanish or

•

French, hit [SETUP], press [

] to point to

“IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then hit [ENTER] repeatedly to

select desired language, then hit [SETUP].

5 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

CHANGE ACCESS CODE

Follow steps to in the “V-CHIP SET UP” sec-

tion on page 16.

4 Enter New code

NEW CODE

Press the Number buttons to enter

your desired access code in the

“NEW CODE” space, then enter

the same code in the “CONFIRM

CODE” space. When completed,

the menu will return to “V-CHIP SET UP”.

X X X X

CONFIRM CODE

Make sure you enter exactly the same new code in

the “CONFIRM CODE” space as one in the

“NEW CODE” space. If they are different, the

“NEW CODE” space is cleared for redoing.

•

5 Exit the V-Chip setting mode

Hit [SETUP] to exit the menu.

NOTE:

Your personal access code will be erased and will

•

return to the default (0000) when a power failure

occurs or when you turn off the power using a

wall switch. If you have forgotten the code, unplug

the power cord for 10 seconds to restore the access

code to 0000.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

Recorded

Playable

discs

Disc size

Region code

Disc types

Mark (logo)

signals

DVD-Video

* 1,2,4,6,10,11

Example

12 cm

8 cm

Title 1

Title 2

DVD-RW

DVD-R

Digital video

(MPEG2)

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1

Chapter 2

* 1,3,4,5,6

7,9,10

DVD+RW

DVD+R

* 1,3,4,5,6,8,9,10

Audio CD

* 4,6,10

Audio CD

Example

12 cm

8 cm

Digital audio

Track 1

Track 2

Track 5

Track 6

Track 3

Track 4

CD-RW

CD-R

* 4,5,6,9,10

is a trademark of DVD Format/Logo Licensing Corporation.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot

be played back.

*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD

recorder. However, depending on the recording status of a disc, the disc may not be played back at all or

normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with

the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may not be smooth, etc.).

*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not

play back properly.

*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.

*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-

mat can only be played back on unit with the same region code.

UNPLAYABLE DISCS

NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3

On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

Any other discs without compatibility indications

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD-V

DVD may contain menus to navigate the disc and

Getting started

access special features. Press the appropriate

Number buttons or [K /L/s / B] to highlight your

selection in the DVD main menu and hit [ENTER] to

confirm.

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

Hit [POWER].

¡The power will turn on.

NOTES:

¡Select DVD mode by hitting [SELECT], then

Hit [OPEN/CLOSE A] to open disc loading

tray.

operate the DVD functions.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Hit [DISC MENU].

¡The DVD main menu will appear.

¡If the feature is not available,

appear on the TV screen.

¡If disc menu is available on the disc, audio language,

subtitle options, chapters for the title and other

options will appear for selection.

symbol may

Hit [PLAY O].

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

¡Closing the disc tray manually or by hitting

[OPEN/CLOSE A] also starts playback.

¡If the playback does not start automatically, hit

[PLAY O].

Press [K /L/s / B] to select an item and

hit [ENTER] to confirm selection.

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case,

refer to “TITLE MENU” on this page.

TITLE MENU

Hit [STOP C] to stop playback.

DVD-V

NOTES:

Hit [TITLE].

¡When the DVD mode has been switched to the TV

mode, the DVD mode shuts down first and then the

TV picture and sound appears in about 4 seconds.

Similarly, when [POWER] is hit to turn off in the

DVD mode, this mode shuts down first and then the

unit is turned off.

¡The title menu will appear.

¡If the feature is not available,

appear on the TV screen.

symbol may

Press [K /L/s / B] to select an item, and

hit [ENTER] to confirm selection.

¡A “prohibited icon” may appear

at the top-right on the TV screen

during operation, warning that a

prohibited operation has been

encountered by the DVD or the

disc.

¡With DVDs that use titles for playback program

signals, playback may start from the second title or

it may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

CALLING UP A MENU SCREEN

DURING PLAYBACK

¡Hit [DISC MENU] to call up the DVD menu.

¡Hit [TITLE] to call up the title menu.

NOTE:

¡Contents of menu and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SLOW FORWARD /

SLOW REVERSE

RESUME

DVD-V

During playback, hit [STOP C].

¡Resume message will appear on the TV screen.

During playback, hit [PAUSE F].

] .

Press [FWD

] or [REV

Hit [PLAY O], playback will resume from the

point at which playback was stopped.

¡“

1” or “

1” appears on the screen.

To select another speed, repeat step 2 until

your required speed number appears on the

screen.

¡To cancel resume, hit [STOP C] twice.

¡The resume information stays on even when the

power is turned off.

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1(1/16), 2(1/8) and 3(1/2).

¡When you press buttons on the front panel, press

PAUSE

DVD-V

and hold [SEARCH

] for a few seconds.

To return to normal playback, hit [PLAY O].

During playback, hit [PAUSE F].

¡Playback will pause and sound will be muted.

To continue playback, hit [PLAY O].

ZOOM

DVD-V

STEP BY STEP PLAYBACK

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

DVD-V

Hit [ZOOM] during playback.

¡Playback will continue.

During playback, hit [PAUSE F].

¡Playback will pause and sound will be muted.

Hit [ZOOM] repeatedly to select the required

zoom factor: ZOOM1, ZOOM2, ZOOM3 or

OFF.

The disc goes forward by one frame each

time [PAUSE F] is hit.

To exit step by step playback, hit [PLAY O].

Press [K /L/s / B] to move the zoomed

picture across the screen.

FAST FORWARD /

FAST REVERSE

To exit zoom mode, hit [ZOOM] to OFF.

NOTES:

¡Zooming function does not work while disc menu is

shown.

DVD-V

¡Zooming function is not available on some discs.

¡It may take several seconds to slide the zoomed pic-

ture.

] or

During playback, press [FWD

[REV

¡“

1” or “

1” appears on the screen.

¡The picture may be distorted if you operate other

To select another speed, repeat step 1 until

your required speed number appears on the

screen.

functions repeatedly (ex. [PAUSE ] or [REV

etc.) in the zoom mode.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).

¡For Audio CDs approximate speed is 1(×2), 2(×8)

and 3(×30).

¡When you press buttons on the front panel, press and

hold [SEARCH

] for a few seconds.

To return to normal playback, hit [PLAY O].

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

DVD-V

There are three ways to begin playback on an Audio

CD at a specific track.

During playback, hit [SEARCH MODE] three

times (CD: twice) to display the Time Search

on the TV screen.

Using the Number buttons

Within 30 seconds, enter a desired disc

time using the Number buttons.

Press the Number buttons to enter the

desired track number.

¡Playback will start at the specified time.

¡Hit [CLEAR] to erase the incorrect input.

¡When there is no need to enter a number, “0”

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, hit [3]).

appears automatically. For example, “ 0 : 0

”

- - -

¡To play track 26, hit [+10], [2], [6].

appears in the Time Search display if the total time

of the track or title is less than 10 minutes.

Using [SEARCH MODE]

Hit [SEARCH MODE].

¡The track search display appears.

MARKER SETUP SCREEN

DVD-V

Within 30 seconds, select the desired track

number using the Number buttons.

Use markers to memorize your favorite places on a

disc.

¡For single digits hit [0] first, if the total track of the

disc is 10 tracks or more.

Hit [SEARCH MODE] four times (CD: three

times) during playback.

¡Playback will start at the selected track.

¡The display screen and Markers will appear on the

TV screen.

Using [SKIP H /

]

During playback, hit [SKIP G] to move the next

track. Hit it repeatedly to skip subsequent tracks. Hit

[SKIP H ] to go back to beginning of the current

track. Hit it repeatedly to go to the previous tracks.

¡If [SKIP H / G] is pressed while the playback

is paused, the playback will be paused again after

skipping to the next track.

Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,

or 10 and ensure that “

appears in the display.

”

- - - - - - - -

When you reach the desired point, hit

[ENTER].

NOTE:

¡The Title or Track and elapsed playing time will

appear in the TV screen.

¡[SKIP H / G] are not operative when playback

is stopped.

To return to the Marker later, hit [SEARCH

MODE] four times (CD: three times) during

playback and press [s / B] to choose the

desired marker, then hit [ENTER].

TITLE / CHAPTER SEARCH

DVD-V

NOTES:

Hit [SEARCH MODE] once for the Chapter

search, twice for the Title search during

¡Operations which erase all Markers:

– Opening the disc tray.

playback.

_/2

– Turning off the power.

– Hitting [SELECT].

– Selecting “AC” at step 2 and hitting [ENTER].

¡To clear a marker:

Enter the desired chapter/title number using

the Number buttons.

– Press [s / B] to select a cursor on to the marker

number and hit [CLEAR].

¡You can mark up to 10 points.

¡Playback will start at the selected chapter or title.

¡Hit [CLEAR] to erase the incorrect input.

¡For single digits hit [0] first, if the total number of

chapter or title of the disc is 10 or more.

Press [SEARCH MODE] or [RETURN] to

exit.

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

You may determine the order in which tracks will play.

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

DVD-V

In the stop mode, hit [MODE].

¡The “PROGRAM” screen will appear.

To activate the repeat function, hit [REPEAT]

during playback.

¡The repeat mode changes as described below every

time you hit the button.

Press [K /L] to select a track, then hit

[ENTER].

¡Hit [CLEAR] to erase the

most recently entered track.

¡If the entire Program cannot be

displayed at once on a screen,

“G” appears to go to the next

page and “H” appears to go

back to the previous page.

PROGRAM

CD-DA

TOTAL 1:03:30

CHAPTER

TITLE

OFF

(repeat off)

3:30

5:10

3:30

4:30

5:00

3:10

5:10

1:30

2:30

10 4:20

11 3:00

12 3:20

17 4:10

22 2:50

2/3

(current chapter repeat) (current title repeat)

ENTER

1/4

PLAY

3:30

CLEAR

NOTES:

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

Hit [PLAY O] to play the programmed tracks.

REPEAT TRACK

NOTES:

¡While the program is being played back, hitting

[STOP C] works as follows.

To activate the repeat function, hit [REPEAT]

during playback.

¡The repeat mode changes as described below every

time you hit the button.

¡Hit [STOP C] once and then [PLAY O] again,

playback will restart from the point where

[STOP C] was hit. (Program continued)

¡Hit [STOP C] twice and then [PLAY O] again,

playback will restart from the track in the usual

way. (Program canceled)

TRACK

(current track repeat)

ALL

OFF

(repeat off)

(entire disc repeat)

¡Up to 99 tracks can be entered.

¡To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at step 2.

¡If you like to repeat the current track in the program,

NOTES:

¡Repeat setting will be cleared when moving to other

hit [REPEAT] several times until “

TRACK”

track.

appears during playback. If you like to repeat the

¡Repeat playback does not function during A-B

repeat playback.

entire program hit [REPEAT] several times until

“

ALL” appears during playback.

A-B REPEAT

RANDOM PLAYBACK

DVD-V CD

¡“

Hit [A-B] at your chosen starting point.

A-” appears briefly on the TV screen.

This function shuffles the playing order of tracks

instead of playback in the sequence.

Hit [A-B] again at your chosen end point.

A-B” appears briefly on the TV screen, and the

In the stop mode, hit [MODE] twice.

¡“

¡“RANDOM” screen appears.

RANDOM

repeat sequence begins.

CD-DA

TOTAL 0:45:55

RANDOM PROGRAM

no indication

To exit the sequence, hit [A-B].

NOTES:

PLAY

¡The A-B repeat section can only be set within the

current title (for DVDs) or current track (for Audio

CDs).

¡A-B repeat is not available with some scenes in

DVD.

¡To cancel the A point which was set, hit [CLEAR].

¡A-B repeat playback does not function during title,

chapter, track or all repeat playback.

Hit [PLAY O] to start random playback.

NOTE:

¡If you like to repeat the current track in the random

selection, hit [REPEAT] several times until

“

TRACK” appears during playback. If you like

to repeat the entire random selection hit

[REPEAT] several times until “ ALL” appears

during playback

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

STEREO SOUND MODE

DVD-V

The unit allows you to select a language for subtitles

during DVD disc (if available) playback.

Hit [AUDIO] repeatedly during playback to

select between “STEREO”, “L-ch” or “R-ch”.

STEREO

Hit [SUBTITLE] during playback.

¡The subtitle language will

appear on the display bar at

the top of the TV screen.

1.ENG/6

STEREO - both right and left channels are active (stereo)

L-ch - only left channel is active

R-ch - only right channel is active

Hit [SUBTITLE] repeatedly to select your

desired subtitle language.

CAMERA ANGLE

DVD-V

To turn off subtitles, hit [SUBTITLE] repeat-

edly until “OFF” appears.

Some DVD discs contain scenes which have been shot

simultaneously from various angles. You can change

NOTES:

the camera angle when the “

screen.

” icon appears on the

¡Hitting [SUBTITLE] may not work on some DVDs

with multiple subtitle languages. In this case, set it

on the disc menu. (Operation varies between discs.

Refer to the manual of the disc.)

Hit [ANGLE] during playback.

¡The selected angle will be displayed on the display

bar at the top of the screen.

¡If the desired language is not shown after hitting

[SUBTITLE] several times, the disc does not have

subtitles in that language.

1 / 8

¡When “NOT AVAILABLE”

appears on the TV screen, it

means no subtitle is recorded

on the scene.

NOT AVAILABLE

¡If the “ANGLE ICON” setting is “OFF” in the

“OTHERS” menu, the “

(Refer to page 28.)

” icon will not appear.

¡If you choose a language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, “---” will be displayed instead.

(Refer to page 26.)

Hit [ANGLE] repeatedly to select your

desired angle.

BLACK LEVEL SETTING

DVD-V

Adjust the Black Level Settings to make the black

parts of the picture brighter.

AUDIO LANGUAGE

Hit [MODE] during playback.

DVD-V

OFF

The unit allows you to select a language during DVD

disc (if multi languages are available) playback.

Hit [AUDIO] during playback.

Hit [ENTER] to switch “ON/OFF”.

1.ENG Dolby D 3/2.1ch 48k/3

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

(Initial setting)

Hit [AUDIO] repeatedly to select your

desired language.

Press [MODE] twice or [RETURN] to exit.

NOTE:

¡The setting will be saved even if the unit is turned

off.

¡Hitting [AUDIO] may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow

audio language setting on the disc menu).

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

VIRTUAL SURROUND

DVD-V

You can enjoy surround-sound effect over two speak-

ers on this unit.

Hit [MODE] twice (CD: once) during play-

back.

OFF

Hit [ENTER] to set it “1” (Natural effect), “2”

(Emphasized effect) or “OFF”.

Hit [MODE] to exit.

¡You can also exit the menu by hitting [RETURN].

NOTE: (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

THE ON-SCREEN INFORMATION

DVD-V

You can check the information about the current disc by hitting [DISPLAY].

For DVD-Vs

For Audio CDs

Hit [DISPLAY] during playback to show cur-

rent Chapter.

Hit [DISPLAY] during playback to show the

current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining playing time of the cur-

9/49

0:00:00 -0:03:30

rent track will be displayed.

4/12 0:03:21 - 0:02:15

Hit [DISPLAY] again to show current Title.

Hit [DISPLAY] again to show current Total

Track.

¡The elapsed and remaining

playing time of the current title

will be displayed.

1/3 0:00:00 - 1:23:45

¡The elapsed and remaining playing time of the total

track will be displayed.

4/12 0:13:45 - 0:45:40

Hit [DISPLAY] again.

¡The bit rate and the current

repeat setting will be

displayed.

Hit [DISPLAY] again to exit.

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

NOTE:

¡When you are playing a disc in PROGRAM or

RANDOM mode, “ PROGRAM” (or RAN-

DOM) will be displayed at step 2.

Hit [DISPLAY] again to exit.

PROGRAM

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE DVD SET UP ITEMS

Language

Code Language

Code

CUSTOM MENU

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

DVD-V

You can change the DVD player’s settings.

Hit [SETUP] twice in the stop mode so that

the DVD SETUP menu appears.

4771 Malayalam

4772 Maltese

4847 Maori

SETUP

¡Hit [L] to select “CUSTOM”

then hit [ENTER].

QUICK

CUSTOM

INITIALIZE

5167 Marathi

Bengali;Bangla

Bhutani

Bihari

4860 Moldavian

5072 Mongolian

4854 Nauru

NOTE:

¡If the menu does not appear, hit [PLAY O] first,

then hit [STOP C]. Make sure the disc is in the stop

mode, then slowly hit [SETUP] twice.

Bislama

Breton

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Select the desired item.

C-E

¡Press [

] to select the desired item then hit

Cambodian

Catalan

[ENTER] to confirm.

Chinese [CHI]

Corsican

Croatian

Refer to the pages below to set up each item.

SETUP

CUSTOM

P 26 Step

Czech

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

LANGUAGE

DISPLAY

AUDIO

PARENTAL

OTHERS

P 27 Step

P 28 Step

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

F-H

P 28 Step

Faroese

Fiji

LANGUAGE SETTING

Follow steps to in the “CUSTOM MENU” section

Finnish [FIN]

French [FRE]

Frisian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

above.

Galician

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Press [

hit [ENTER].

] to select the desired item then

5051 Sindhi

5158 Singhalese

5758 Siswat

5360 Slovak

SETUP

LANGUAGE

AUDIO:

Sets the audio language.

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

OFF

SUBTITLE:

ENGLISH

Sets the subtitle language.

DISC MENU:

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Swedish [SWE]

Sets the language for DVD menu.

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

] to select a setting then hit

Press [

[ENTER].

SETUP

LANGUAGE

¡If “OTHER” is selected on

the “AUDIO”, “SUBTITLE”

or “DISC MENU” screen,

press four-digit number to

enter the code for the

desired language. (Refer to

the language code list.)

¡Only the languages support-

ed by the disc can be select-

ed.

AUDIO

ORIGINAL

ENGLISH

FRENCH

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

SETUP

SUBTITLE

OFF

ENGLISH

FRENCH

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Korean [KOR]

Kurdish

6460

U-Z

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

SETUP

DISC MENU

ENGLISH

FRENCH

Vietnamese

Volapuk

Welsh

SPANISH

Wolof

Xhosa

Yiddish

Hit [SETUP] to exit the menu.

NOTES:

Yoruba

Zulu

¡Language Setting for Audio and Subtitle are not

valid for some discs due to default setting of the

disc. In this case, set them by hitting [AUDIO] and

[SUBTITLE]. (Refer to page 24.)

¡If you select a language that is not supported by the

disc, subtitle will automatically be set OFF and the

first item of the audio languages will be automatical-

ly set.

If you choose a language that has a 3 letter language

code, the code will be displayed every time you change

the AUDIO or SUBTITLE language setting above. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY SETTING

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Follow steps to in the “CUSTOM MENU” section

on page 26.

Press [

] to select the below items then

Follow steps to in the “CUSTOM MENU” section

on page 26.

hit [ENTER].

TV MODE:

QUICK

Press [

] to select the below items then

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

hit [ENTER].

DRC (Dynamic Range

Control):

¡To compress the range of soft

to loud sound.

¡4:3 LETTER BOX (default):

To show black bars on top

and bottom of the screen.

SETUP

DISPLAY

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

BITSTREAM

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

¡4:3 PAN & SCAN: To show

a full height picture with both sides trimmed.

¡The default setting is “ON”.

DOWN SAMPLING:

¡ON : Output in 48 kHz.

(default)

¡OFF : Output the original

sound.

When playing disc with copyright Protection

¡If you select “OFF”, copyright protection will be

activated and sound will be down sampled at 48kHz.

SETUP

AUDIO

DRC

DOWN SAMPLING

DOLBY DIGITAL

BITSTREAM

STILL MODE

This function allows you to adjust picture resolution

and quality in the still mode.

SETUP

DISPLAY

¡AUTO (default):

Automatically select the best

resolution setting (FRAME

or FIELD) based on the data

characteristics of the pictures.

¡FIELD: Select “FIELD” when the pictures are still

unstable even if “AUTO” is selected.

FIELD stabilizes the pictures, although the picture

quality may become coarse due to the limited

amount of data.

¡FRAME: Select “FRAME” to display relatively

motionless pictures in higher resolution.

FRAME improves the picture quality, although it

may unstabilizethe pictures due to simultaneous

output of two field data.

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

DOLBY DIGITAL:

QUICK

BITSTREAM

Set to “BITSTREAM” when

the unit is connected to a

Dolby Digital Decoder.

¡BITSTREAM: Output a Dolby Digital signal

(default)

¡PCM: Convert the Dolby Digital to PCM

(2 channel stereo)

Hit [SETUP] to exit the menu.

QUICK MENU

¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the

QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 26.

LANGUAGE SETTING FOR THE ON-SCREEN MENUS

¡You can access the TV SETUP menu by hitting [SETUP] from the DVD mode. Refer to

“MENU LANGUAGE” on page 17 to change the language for the on-screen menus.

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL CONTROL

IF YOU FORGET THE PASSWORD

Parental Control limits the disc viewing that exceed

your setting (with a password or playback will stop).

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Hit the Number buttons [4], [7], [3], [7] at

step 3. Then enter your new password.

¡Password will be cleared and parental level will be

set to “ALL”.

PARENTAL LEVEL

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Proceed with steps 4 to 6 again.

OTHER SETTINGS

Follow steps 1 to 2 in the “CUSTOM MENU” section

on page 26.

Follow steps to in the “CUSTOM MENU” section

on page 26.

Enter your four-digit password then hit

[ENTER].

Press [

] to select the below items, then

SETUP

PARENTAL

PASSWORD

Enter current password.

hit [ENTER].

SETUP

OTHERS

ANGLE ICON

AUTO POWER OFF ON

ANGLE ICON:

¡Hit [ENTER] repeatedly to turn Angle icon “ON” or

“OFF”.

] to select “PARENTAL LEVEL”

Press [

SETUP

PARENTAL

then hit [ENTER].

PARENTAL LEVEL

PASSWORD CHANGE

ALL

¡The default setting is “ON”.

AUTO POWER OFF:

¡Hit [ENTER] repeatedly to turn Auto Power off

] to select the desired level then

Press [

“ON” or “OFF”.

hit [ENTER].

SETUP

PARENTAL

PARENTAL LEVEL

The default setting is “ON” and the screen saver pro-

gram starts when there is no input from the unit for 5

minutes in the stop mode. After the screen saver pro-

gram is activated for 15 minutes, the power is auto-

matically turned off.

ALL

7 [NC-17]

6 [R]

Hit [SETUP] to exit the menu.

NOTES:

Hit [SETUP] to exit the menu.

When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the pass-

word. (in the event you forget the password, see below)

¡To change the password, press [

] to select

INITIALIZE

“PASSWORD CHANGE” at step 4 then hit

[ENTER]. Enter the four-digit password, then hit

[ENTER].

DVD-V

This allows you to return all selections of SETUP

(except for “PARENTAL” and menu language) to

their default settings.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

Hit [SETUP] twice in the stop mode so that

the “INITIALIZE” menu appears.

¡Record the password in case you forget it.

CONTROL LEVELS

Press [

] to select “INITIALIZE” then hit

ALL

SETUP

[ENTER].

QUICK

CUSTOM

INITIALIZE

All parental lock is cancelled.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Press [

] to select “YES” then hit

[ENTER] twice.

Levels 7 to 2

All the settings (except for

“PARENTAL” and menu

language) will be cleared.

¡To cancel the initialization,

select “NO”.

Only DVD software intended for general use and

children can be played back.

SETUP

INITIALIZE

Initialize?

YES

Level 1

Only DVD software intended for children can be

played back, with those intended for adult and gen-

eral use prohibited.

Hit [SETUP] to exit the menu.

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-

sulting the following checklist.

PROBLEM

CORRECTIVE ACTION

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote control.

You have to be within 23 feet of the unit.

No power

•

No operation by infrared remote

control

•

Check if the correct mode is selected. If not switch the mode by

hitting [SELECT], whichever you need.

TV Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture or sound

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Hit [SELECT] to select TV mode.

Then try other TV feature.

•

Let the unit program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Check for broken pin of the antenna cable.

Adjust volume control on remote control or main unit.

Hit [MUTE] to restore sound.

•

No picture or poor picture on the

unit

No sound or poor sound

Bars On Screen

If outside antenna is being used, check for broken wire.

Check for local interference.

Picture Distorted or Blurred

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “COLOR” control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “CONTRAST” & “BRIGHT” control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Adjust “CONTRAST” & “BRIGHT” control.

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

Picture OK, Sound Poor

CORRECTIVE ACTION

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair immedi-

ately, unplug the power cord, then plug it in again 30 minutes later or

so. This automatically resets the unit.

•

No operation by infrared remote

control

Different color marks on screen

•

CLOSED CAPTION PROBLEM

POSSIBLE REMEDY

Misspelling in captions

Error committed by the closed captioning production company.

Possible in a live broadcast. Not in case of a prerecorded program.

A few seconds of delay is common for live broadcast.

Display capacity may not exceed 220 words per minute. If a dialogue

exceeds that rate, selective editing is used to insure that the captions

remain up-to-date with the current TV screen dialogue.

•

Text is not shown in its entirety or

a delay occurs from what is being

said

Captions scrambled with white

boxes

Caused by interferences of building, power lines, thunderstorms, etc.

No captions in a program which

must contain closed caption

The broadcast may use a time compression process to speed up the

program. The decoder cannot read the compressed information and

captions will be lost.

You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or

Caption “OFF”.

•

Black box in the TV screen

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

PROBLEM

CORRECTIVE ACTION

Insert a correct video disc that plays on this unit.

Hit [SELECT] to select DVD mode, then try other DVD feature.

Insert the disc.

No picture

•

Disc cannot be played

Clean the disc.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control level.

Connect the audio cables firmly.

No sound

Turn the power of the audio component on.

Correct the audio output settings.

Correct the input settings on the audio component.

This unit does not support DTS audio. This is not a malfunction.

No DTS audio is output

Distorted picture

There are some cases where pictures may be slightly distorted,

which are not a sign of a malfunction.

Although pictures may stop for a moment, this is not a malfunction.

The selected language is not available for audio or subtitles on the

DVD. (This is not a malfunction.)

•

Audio or subtitle language

does not match the set up

The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-

•

era angles. (This is not a malfunction.)

Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected

•

changed

language. (This is not a malfunction.)

•

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

That operation is prohibited by the unit or the disc.

(This is not a malfunction.)

Scratched disc. Replace the disc with an unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

CABINET CLEANING

SERVICING

Should your unit become inoperative, do not try to

•

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and please call our help line mentioned on

the front page, to locate an Authorized Service

Center.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the unit still does not perform properly when it is operated, while referring to the relevant sections and to

“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.

•

Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup

unit.

DISC HANDLING

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

Do not use detergent or abrasive cleaning agents.

Always store the disc in its protective case when it

is not used.

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

CRT:

20 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Antenna input:

Television system:

Closed caption system: §15.119/FCC

Channel coverage:

VHF:

UHF:

CATV:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video input:

Audio L/R input:

Headphone:

2 ~ 13

14 ~ 69

1/8" stereo (3.5 mm)

2 ~13, A ~ W,

W+1 ~ W+84,

A-5 ~ A-1, 5A

181 channel

frequency synthesized

tuning system

Direct access keyboard,

programmable

scan and up/down

Coaxial digital

audio output:

One pin jack,

500m Vpp (75 ohm)

Digital encoded

Tuning System:

Channel access:

Remote control:

infrared light system

Operating

temperature:

5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

(Maximum):

Picture tube:

Dimensions:

80W

20" PF

H : 20-1/4" (514mm)

W : 20-3/16" (512mm)

D : 19-13/16" (503mm)

46.3 lbs. (21.0kg)

DVD

Product type:

Discs:

Output signal format: NTSC color

DVD Player

DVD video, Audio CD

Weight:

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

INDICE

■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

SECCIÓN DE TV

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35

CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 36

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 37

IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 38

MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

EQUIPADO CON TOMAS DE ENTRADA DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 36

CONTROLES DE OPERACIÓN Y FUNCIONES

• Consulte la figura 1 de la página 8 para el panel frontal de la unidad

• Consulte la figura 2 de la página 8 para el mando a distancia

• Consulte la figura 3 de la página 9 para la vista posterior

1. Bandeja de carga del disco

2. Toma de entrada VIDEO

Conecte aquí la toma de salida de vídeo de una

videocámara o de una videograbadora.

Botón +100

Presione para seleccionar canales de televisión por

cable cuyo número sea superior a 99.

Modo DVD:

Presione para introducir el número deseado.

Botón +10

Presione para introducir números superiors a 9.

3. Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

16. Botón SLEEP

4. Botón POWER

Presione para encender y apagar la unidad.

Utilise para ajustar el temporizador de dormir.

17. Botón DISPLAY

5. Botones VOLUME (VOL.)

Modo TV:

Presione para controlar el nivel de volumen del DVD y

el televisor.

Indica el número del canal en la pantalla del televisor.

Modo DVD:

Indica el estado actual en la pantalla del televisor.

6. Botones CHANNEL (CH.)

Utilice para seleccionar canales memorizados.

7. Ventanilla del sensor de mando a distancia

8. Botón STOP

Detiene la operación del disco.

9. Botones SKIP H /

Presione una vez para omitir capítulos o pistas y

desplazarse a un punto específico.

18. Botón SETUP

Presione para entrar o salir del menú de configuración

de televisor o DVD.

19. Botón TITLE

Para visualizar el menú de títulos.

20. Botón CLEAR

Para cancelar o borrar un ajuste entrado actualmente.

Botones SEARCH

(Panel frontal)

21. Botón MODE

Mantenga el botón presionado para cambiar la

velocidad de reproducción en avance o retroceso.

Presione para llamar la pantalla de la reproducción

programada o la de reproducción aleatoria en el modo

de parada.

10. Botón PLAY

Inicia la reproducción del contenido del disco.

11. Botón PAUSE

Hace una pausa en la reproducción del disco.

12. Botón OPEN/CLOSE

Presione para llamar la pantalla de ajuste del nivel del

negro o la pantalla de sonido ambiental durante la

reproducción.

22. Botón SEARCH MODE

Presione para insertar un disco en la bandeja o retirarlo

de ella.

Presione para localizar un punto deseado.

23. Botón AUDIO

13. Toma HEADPHONE

Presione para seleccionar un modo de sonido o idioma

de audio deseado.

Para conectar auriculares (no suministrados) y escuchar

en privado.

24. Botón SUBTITLE

14. Botón PICTURE

Presione para seleccionar el idioma de subtítulos

deseado.

Presione para ajustar la imagen.

15. Botones Numéricos

25. Botón REPEAT

Modo TV:

Repite la reproducción del disco, título, capítulo o pista

actual.

Presione dos cifras para acceder directamente al canal

deseado.

26. Botón ANGLE

No olvide presionar [0] antes de elegir un canal de una

Presione para cambiar el ángulo de la cámara y ver la

secuencia que se está reproduciendo desde un ángulo

diferente (si existe).

sola cifra.

- 34 -

Download from Www.Somanuals.com. All Manuals Search And Download.

33. Botón ZOOM

27. Botón A-B

Amplía parte de la imagen reproducida de un DVD.

Repite la reproducción de una sección seleccionada.

34. Botón MUTE

28. Botón RETURN

Suprime la salida de sonido. Presiónelo de nuevo para

restablecer el sonido.

Permite volver a la pantalla anterior en el menú de

configuración.

35. Botón SELECT

29. Botón ENTER

Presione para cambiar al modo TV, modo de entrada

externa o modo de DVD.

Presione para establecer un ajuste.

{

30. Botones

Modo TV:

36. Toma COAXIAL

Conecte solamente a la entrada digital de un

amplificador externo o decodificador (para audio de

DVD solamente).

Presione para seleccionar un modo de ajuste en el

menú que aparece en la pantalla del televisor.

Presiónelos también para seleccionar opciones o

establecer ajustes en un menú en particular.

Modo DVD:

37. Toma ANT.

Conecte a una antena, sistema de televisión por cable o

sistema de satélite.

Presione para hacer una selección en el menú.

31. Botón DISC MENU

38. Cable eléctrico

Muestra menú del DVD.

Conécte a un toma de CA estándar (120 V/60 Hz).

NOTA:

32. Botón REV

Antes de conectar el cable eléctrico a una toma de

Presione para mover la imagen de DVD en retroceso

rápido en o en cámara lenta en retroceso.

•

CA, retírelo del gancho para evitar dañarlo.

Botón FWD

Presione para mover en avance rápido o en cámara

lenta en el disco.

PREPARACIÓN PARA LA UTILIZACIÓN

NOTA:

CONEXIONES DE ANTENA/CABLE

Antes de enchufar la antena a la toma ANT. de la

unidad, compruebe que la clavija no esté doblada.

Si esta doblada, póngala derecha como se muestra

en la ilustración, y luego conéctela en la toma

ANT. de la unidad.

Consulte la figura 4 de la página 10

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que

proporciona recomendaciones para hacer una

conexión a tierra apropiada y, en particular,

especifica que la tierra del cable debe conectarse

al sistema de puesta a tierra del edificio, tan cerca

del punto de entrada del cable como sea posible.

Clavija doblada

Cable

Clavija

(Necesita enderezarse)

(Clavija derecha)

NOTA:

Para su seguridad y para evitar que se dañe

la unidad, desenchufe el cable de antena de la

toma ANT. antes de mover la unidad.

•

- 35 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIÓN A TOMAS DE

ENTRADA DELANTERAS

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada AUDIO/VIDEO de la parte delantera de la

unidad.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de esta

unidad.

CONEXIÓN A UN

DECODIFICADOR DOLBY

DIGITAL (para DVD)

Si utiliza esta unidad para reproducir un disco DVD

en un formato de sonido envolvente Dolby Digital de

5,1 canales, la unidad dará salida a un flujo de datos

DOLBY DIGITAL desde su toma COAXIAL. Si

conecta la unidad a un decodificador Dolby Digital,

podrá disfrutar de una tonalidad más convincente y

real, con un sonido envolvente potente y de alta

calidad similar al de los cines.

] hasta

Despúes, presione [SELECT] o [CH.

que aparezca “AUX” en la pantalla.

Utilice cables digitales coaxiales de audio

(disponibles en el comercio) para hacer las

conexiones de audio.

Consulte la figura 5 de la página 11

NOTA:

•

Cuando conecte una videograbadora monofónica

(otra fuente) a esta unidad, conecte la toma de

salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de esta unidad. El

audio saldrá igualmente por los canales izquierdo y

derecho.

Consulte la figura 7 de la página 12

NOTAS:

Asegúrese de apagar todos los componentes del

•

sistema antes de conectar otro componente.

Consulte los manuales de instrucciones de los

•

componentes que va a conectar a la unidad.

Si conecta un decodificador Dolby Digital, ajuste

•

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CON TOMAS

DE ENTRADA DIGITAL (para DVD) •

la función “DOLBY DIGITAL” a “BITSTREAM”

para salida de audio en el modo de configuración.

A menos que se haga la conexión a un

decodificador Dolby Digital, ajuste la función

“DOLBY DIGITAL” a “PCM” para salida de

audio en el modo de configuración. La

Utilice un cable digital coaxial de audio (disponible en

el comercio) para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

Consulte la figura 6 de la página 11

NOTAS:

• La fuente de audio de un disco grabado en formato

de sonido envolvente Dolby Digital de 5,1 canales

no se puede grabar como sonido digital mediante

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la

doble D son marcas comerciales de Dolby

Laboratories.

• ^uAⁿs^aeg^pú^lare^tisⁿe^ad^Me ^Dap^oag^Dar^At^To^.dos los componentes del

• ^sC^iso^tn^es^mul^ate^anlo^tes^sm^da^en^cu^oaⁿle^es^ctd^ae^{r o}in^trs^otru^cocc^mio^pn^oeⁿs^end^te^e.los

PARA INSERTAR LAS PILAS

• A^coj^mus^pte^onla^enf^tu^en^sc^qió^un^e“^vD^aO^aL^coBⁿY^ecD^taI^rG^aIT^laA^uLⁿ”^ida^a“^dP^.CM”

para salida de audio en el modo de configuración.

La reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a

distancia en el sentido de la flecha.

2) Inserte 2 pilas “AA” en el

compartimiento de las pilas, en el

sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

- 36 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SECCIÓN DE TV

PARA MIRAR UN

IDIOMA DEL MENÚ

PROGRAMA DE TV

1 Seleccione “LANGUAGE”

Presione [SETUP].

1 Enchufe el cable eléctrico

Enchufe el cable eléctrico de la unidad en un

tomacorriente de CA del hogar.

NOTA:

•

Presione [

] para apuntar a “LANGUAGE”.

2 Seleccione “ENGLISH”, “ESPAÑOL” o

Si aparecen números en la esquina de la pantalla,

“FRANÇAIS”

presione [POWER] sin desenchufar el cable

Presione [ENTER] repetidamente para seleccionar

“ENGLISH” = inglés, “ESPAÑOL” o

“FRANÇAIS” = francés.

eléctrico.

2 Encienda la unidad

Presione [POWER] para encender la unidad.

3 Salga del modo de idioma

Presione [SETUP] para salir del menú.

NOTAS:

3 Seleccione el número de canal

Presione [CH.

] o los botones numéricos para

seleccionar su número de canal deseado.

Esta función afecta sólo el idioma en el menú de la

pantalla y no la fuente de audio.

•

Nota para el uso de los botones numéricos:

¡Debe colocar un cero antes de los números de canal

de una sola cifra (por ejemplo: 02, 03, 04, etc.).

Si por alguna razón, el menú está en francés,

presione [SETUP], presione [

•

] para apuntar

Cuando seleccione canales de cable de más de 99,

presione primero [+100] y después las dos últimas

cifras. (Ejemplo: para seleccionar el canal 125,

primero presione [+100] y después presione [2] y [5].)

al “LANGAGE [FRANÇAIS]” y presione

[ENTER] repetidamente para seleccionar el

idioma deseado y presione [SETUP].

4 Ajuste el sonido

Presione [VOL.

] para ajustar el volumen.

Presione [MUTE] para silenciar instantáneamente el

sonido.

Presione nuevamente para recuperar el nivel de

sonido anterior.

NOTA:

Si presione [CH.

] en el modo DVD, puede

•

cambiar los canales de TV. Incluso si apaga la

unidad en el modo DVD, cuando vuelva a

encender, volverá al modo TV.

PARA VER CANALES DE CABLE O

SATELITE

Si la unidad está conectada a una caja de cable o

•

] para

caja de satélite, presione [CH.

seleccionar CH3 o CH4 de acuerdo con el ajuste

de canal de salida del dispositivo y seleccione el

canal deseado en el dispositivo.

PARA VER UNA ENTRADA EXTERNA

Cuando se conecta un equipo externo en las tomas

•

de entrada AUDIO/VIDEO frontales, presione

[SELECT] o [CH.

] repetidamente hasta que

aparezca “AUX” en la pantalla.

- 37 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA

MENÚ DE DISCO

DVD-V

Para empezar

Presione [DISC MENU].

¡Conecte la alimentación del amplificador y otros ¡Aparecerá el menú principal de DVD.

componentes, si es necesario.

¡Si no existe la función, puede aparecer el símbolo

en la pantalla de TV.

Presione [POWER].

¡La alimentación se conectará.

¡Si el menú de disco existe en el disco, aparecerán el

idioma de audio, opciones de subtítulo, capítulos

para el título y otras opciones para su selección.

Presione [OPEN/CLOSE A] para abrir la

bandeja de carga del disco.

{

Presione [

] para hacer una

Ponga el disco deseado en la bandeja, con

la etiqueta hacia

arriba.

selección y presione [ENTER] para

confirmar la selección.

REANUDACIÓN

DVD-V

Durante la reproducción, presione

[STOP C].

Presione [PLAY O].

¡Aparecerá el mensaje de continuación en la pantalla

¡La bandeja se cerrará automáticamente y la

reproducción comenzará desde el primer capítulo o

pista del disco.

de TV.

Presione [PLAY O], la reproducción continuará

desde el punto donde se paró la reproducción.

¡La reproducción también empieza cerrando

manualmente la bandeja del disco o presionando

[OPEN/CLOSE A].

¡Si la reproducción no comienza automáticamente,

presione [PLAY O].

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la pantalla.

¡Para cancelar la continuación, presione dos veces

[STOP C].

¡La información de continuación permanece activada

incluso cuando apaga el interruptor principal.

Presione [STOP

C] para detener la reproducción.

- 38 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

- 39 -

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNAI CORPORATION

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship

as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date

of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail

purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does

not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE

PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN

THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest Authorized Service Center or for general service inquiries, please call or

write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-242-7158

http://www.Symphonic.us

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia

1EMN20326

T9102UC ★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

Snapper Lawn Mower 1690583 User Manual
Sony Digital Camera DSC F505 User Manual
Sony MP3 Docking Station SRSBTX500 User Manual
Sony Portable CD Player MZ E501 User Manual
SOYO Computer Hardware SY 6VBA 133 User Manual
Speco Technologies Computer Monitor PVM 2 User Manual
Sterling Plumbing Product e049400 User Manual
Subaru Robin Power Products Laptop RGX2900 User Manual
SunBriteTV Flat Panel Television 46 006 4660HD 111005 User Manual
Sylvania TV VCR Combo 6313CB 6319CB User Manual