LS 2100
Product Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Undecoded Scanner
Product Reference Guide
70-32818-01
Revision B
April 2001
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 by Symbol Technologies, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or
mechanical means, without permission in writing from Symbol. This includes electronic or
mechanical means, such as photocopying, recording, or information storage and retrieval
systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware,
furnished to the user is on a licensed basis. Symbol grants to the user a non-transferable and
non-exclusive license to use each software or firmware program delivered hereunder (licensed
program). Except as noted below, such license may not be assigned, sublicensed, or otherwise
transferred by the user without prior written consent of Symbol. No right to copy a licensed
program in whole or in part is granted, except as permitted under copyright law. The user
shall not modify, merge, or incorporate any form or portion of a licensed program with other
program material, create a derivative work from a licensed program, or use a licensed
program in a network without written permission from Symbol. The user agrees to maintain
Symbol’s copyright notice on the licensed programs delivered hereunder, and to include the
same on any authorized copies it makes, in whole or in part. The user agrees not to
decompile, disassemble, decode, or reverse engineer any licensed program delivered to the
user or any portion thereof.
Symbol reserves the right to make changes to any software or product to improve reliability,
function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any
Symbol Technologies, Inc., intellectual property rights. An implied license only exists for
equipment, circuits, and subsystems contained in Symbol products.
Symbol, Spectrum One, and Spectrum24 are registered trademarks of Symbol Technologies,
Inc. Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Setting Up the LS 2100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Switching Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Connecting to a Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Chapter 2. Scanning with the LS 2100
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Scanning with the LS 2100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Aiming the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
LS 2100 Decode Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Chapter 3. Maintenance and Specifications
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Standard Accessories: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
LS 2100 Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Glossary
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
The LS 2100 Undecoded Scanner Product Reference Guide provides general instructions for the setup,
programming, operation, troubleshooting, and maintenance of the LS 2100 scanner.
Notational Conventions
The following conventions are used in this document:
!
Bullets (!) indicate:
"
"
"
action items
lists of alternatives
lists of required steps that are not necessarily sequential
!
Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Related Publications
!
!
!
LS 2104 Product Reference Guide
LS 2106 Product Reference Guide
p/n 70-32817-xx
p/n 70-32820-xx
p/n 70-32821-xx
Service Inform ation
If you have a problem with your equipment, contact the Symbol Support Center for your region. See
page vi for contact information. Before calling, have the model number, serial number, and several of
your bar code symbols at hand.
Call the Support Center from a phone near the scanning equipment so that the service person can try
to talk you through your problem. If the equipment is found to be working properly and the problem
is symbol readability, the Support Center will request samples of your bar codes for analysis at our
plant.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
If your problem cannot be solved over the phone, you may need to return your equipment for servicing.
If that is necessary, you will be given specific directions.
Note: Symbol Technologies is not responsible for any damages incurred during
shipment if the approved shipping container is not used. Shipping the units
improperly can possibly void the warranty. If the original shipping container
was not kept, contact Symbol to have another sent to you.
Symbol Support Center
For service information, warranty information or technical assistance contact or call the Symbol
Support Center in:
United States
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, New York 11742-1300
1-800-653-5350
Canada
Symbol Technologies Canada, Inc.
2540 Matheson Boulevard East
Mississauga, Ontario, Canada L4W 4Z2
905-629-7226
United Kingdom
Asia/Pacific
Symbol Technologies Asia, Inc.
230 Victoria Street #04-05
Symbol Technologies
Symbol Place
Winnersh Triangle, Berkshire RG41 5TP
United Kingdom
Bugis Junction Office Tower
Singapore 188024
0800 328 2424 (Inside UK)
337-6588 (Inside Singapore)
+44 208 945 7529 (Outside UK)
+65-337-6588 (Outside Singapore)
Australia
Symbol Technologies Pty. Ltd.
432 St. Kilda Road
Austria
Symbol Technologies Austria GmbH
Prinz-Eugen Strasse 70
Melbourne, Victoria 3004
Suite 3
1-800-672-906 (Inside Australia)
2.Haus, 5.Stock
+61-3-9866-6044 (Outside Australia)
1040 Vienna, Austria
1-505-5794 (Inside Austria)
+43-1-505-5794 (Outside Austria)
Denmark
Symbol Technologies AS
Europe/Mid-East Distributor Operations
Contact your local distributor or call
Gydevang 2,
+44 208 945 7360
DK-3450 Allerod, Denmark
7020-1718 (Inside Denmark)
+45-7020-1718 (Outside Denmark)
Finland
Oy Symbol Technologies
Kaupintie 8 A 6
France
Symbol Technologies France
Centre d'Affaire d'Antony
FIN-00440 Helsinki, Finland
9 5407 580 (Inside Finland)
+358 9 5407 580 (Outside Finland)
3 Rue de la Renaissance
92184 Antony Cedex, France
01-40-96-52-21 (Inside France)
+33-1-40-96-52-50 (Outside France)
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Germany
Symbol Technologies GmbH
Waldstrasse 68
D-63128 Dietzenbach, Germany
6074-49020 (Inside Germany)
+49-6074-49020 (Outside Germany)
Italy
Symbol Technologies Italia S.R.L.
Via Cristoforo Columbo, 49
20090 Trezzano S/N Navigilo
Milano, Italy
2-484441 (Inside Italy)
+39-02-484441 (Outside Italy)
Latin America Sales Support
7900 Glades Road
Mexico
Symbol Technologies Mexico Ltd.
Torre Picasso
Suite 340
Boca Raton, Florida 33434 USA
1-800-347-0178 (Inside United States)
+1-561-483-1275 (Outside United States)
Boulevard Manuel Avila Camacho No 88
Lomas de Chapultepec CP 11000
Mexico City, DF, Mexico
5-520-1835 (Inside Mexico)
+52-5-520-1835 (Outside Mexico)
Netherlands
Symbol Technologies
Norway
Symbol Technologies
Kerkplein 2, 7051 CX
Trollasveien 36
Postbus 24 7050 AA
Postboks 72
Varsseveld, Netherlands
315-271700 (Inside Netherlands)
+31-315-271700 (Outside Netherlands)
1414 Trollasen, Norway
66810600 (Inside Norway)
+47-66810600 (Outside Norway)
South Africa
Symbol Technologies Africa Inc.
Block B2
Spain
Symbol Technologies S.A.
Edificioi la Piovera Azul
Rutherford Estate
1 Scott Street
C. Peonias, No. 2 - Sexta Planta
28042 Madrid, Spain
Waverly 2090 Johannesburg
Republic of South Africa
11-4405668 (Inside South Africa)
+27-11-4405668 (Outside South Africa)
9-1-320-39-09 (Inside Spain)
+34-9-1-320-39-09 (Outside Spain)
Sweden
Symbol Technologies AB
Albygatan 109D
Solna
Sweden
84452900 (Inside Sweden)
+46 84452900 (Outside Sweden)
If you purchased your Symbol product from a Symbol Business Partner, contact that Business Partner
for service.
W arranty
Symbol Technologies, Inc (“Symbol”) manufactures its hardware products in accordance with industry-
standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment,
products will be free from defects in materials and workmanship.
-vii
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
This warranty is provided to the original owner only and is not transferable to any third party. It shall
not apply to any product (i) which has been repaired or altered unless done or approved by Symbol, (ii)
which has not been maintained in accordance with any operating or handling instructions supplied by
Symbol, (iii) which has been subjected to unusual physical or electrical stress, misuse, abuse, power
shortage, negligence or accident or (iv) which has been used other than in accordance with the product
operating and handling instructions. Preventive maintenance is the responsibility of customer and is not
covered under this warranty.
Wear items and accessories having a Symbol serial number, will carry a 90-day limited warranty. Non-
serialized items will carry a 30-day limited warranty.
Warranty Coverage and Procedure
During the warranty period, Symbol will repair or replace defective products returned to Symbol’s
manufacturing plant in the US. For warranty service in North America, call the Symbol Support Center
at 1-800-653-5350. International customers should contact the local Symbol office or support center.
If warranty service is required, Symbol will issue a Return Material Authorization Number. Products
must be shipped in the original or comparable packaging, shipping and insurance charges prepaid.
Symbol will ship the repaired or replacement product freight and insurance prepaid in North America.
Shipments from the US or other locations will be made F.O.B. Symbol’s manufacturing plant.
Symbol will use new or refurbished parts at its discretion and will own all parts removed from repaired
products. Customer will pay for the replacement product in case it does not return the replaced product
to Symbol within 3 days of receipt of the replacement product. The process for return and customer’s
charges will be in accordance with Symbol’s Exchange Policy in effect at the time of the exchange.
Customer accepts full responsibility for its software and data including the appropriate backup thereof.
Repair or replacement of a product during warranty will not extend the original warranty term.
Symbol’s Customer Service organization offers an array of service plans, such as on-site, depot, or phone
support, that can be implemented to meet customer’s special operational requirements and are available
at a substantial discount during warranty period.
General
Except for the warranties stated above, Symbol disclaims all warranties, express or implied, on products
furnished hereunder, including without limitation implied warranties of merchantability and fitness for
a particular purpose. The stated express warranties are in lieu of all obligations or liabilities on part of
Symbol for damages, including without limitation, special, indirect, or consequential damages arising
out of or in connection with the use or performance of the product.
Seller’s liability for damages to buyer or others resulting from the use of any product, shall in no way
exceed the purchase price of said product, except in instances of injury to persons or property.
Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential
damages, so the proceeding exclusion or limitation may not apply to you.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Setting Up the LS 2100
Introduction
industrial applications. Advanced ergonomic design ensures comfortable use for extended
periods of time.
The LS 2100 Series hand-held scanner is based on the SE 1200 Series scan engine with Visible
Laser Diode (VLD) and mylar® scan element. This state of the art technology gives the
scanner a wider decode zone, greater depth of field, and a visible scan beam. This series reads
color bar codes and symbols printed on all substrates. See the LS 2100 Decode Zone on page
2-4.
Figure 1-1. LS 2100 Scanner
Here’s what each member of the LS 2100 family offers you:
!
LS 2100 - The aggressiveness of this discrete scanner is typical of the
LS 2100 family’s performance. It connects easily to, and is programmed by, the
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
complete line of Symbol Technologies portable terminals and the full range of
SYMBOL and OmniLinkTM interface controllers.
!
LS 2104 - With a simple cable change, this scanner is compatible with:
"
"
RS 232C asynchronous terminals
SynapseTM “Smart Cables”, which allow you to connect to:
"
"
"
"
"
IBM 4683/4, 4693/4 series of terminals
All leading OCIA terminals, including NCR, Nixdorf, and ICL terminals
Popular OCR terminals, such as Fujitsu and ICL.
Wand Emulation terminals
Dual RS-232 Hosts
!
LS 2106 - The LS 2106 scanner is a keyboard “wedge” interface which adds efficient,
reliable bar code reading to your PS/2or AT/XT terminal. Since entered scan data is
scanner contains on-board discrete keyboard wedge communications for connecting
to asynchronous terminals and host systems. It can also accommodate any of the
Synapse™ “Smart Cables” which allows you to connect to a wide variety of host
systems. Some installations require one cable; others require additional adapters
between the keyboard, the PC, and the y-cable.
All of the LS 2100 series scan automatically at the rate of 36 scans per second. For decode
capability, see Technical Specifications on page 3-3.
Audience
The intended audience for this manual is personnel performing installation/setup and
programming of LS 2100 scanners.
Unpacking
Remove the LS 2100 from its packing and inspect it for damage. If the scanner was damaged
in transit, call the Symbol Support Center at one of the telephone numbers listed on page vi.
KEEP THE PACKING. It is the approved shipping container and should be used if you ever
need to return your equipment for servicing.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the LS 2100
Setting Up the LS 2100
Installing the Cable
Insert the cable into the receptacle on the bottom of the scanner, as shown below:
Figure 1-2. Installing the Cable
Switching Cables
Different cables are required for different hosts. To change the scanner cable:
1. Press the tab on the cable with a small screwdriver.
2. Pull the cable out of the receptacle on the bottom of the scanner.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
3. Insert a new cable in the receptacle. Press the cable firmly into the receptacle until
you hear a click.
Connecting to a Host
Plug the connector at the end of the LS 2100 cable into the appropriate port on the Symbol
interface controller or portable terminal. Refer to the controller user documentation for full
details.
LS 2100
Host
Com puter
Interface
Controller
Portable
Data
Te r m i n a l
LS 2100
Figure 1-3. Connecting to a Host
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Scanning with the LS 2100
Introduction
This chapter covers the proper techniques for scanning bar codes and the decode zone for the
LS 2100 scanner.
Scanning with the LS 2100
1. Before you use the scanner, make sure all cable connections are secure.
2. Make sure the bar code is in the correct scanning range. Aim and press the trigger;
the scan beam lights and an orange light illuminates at the rear of the scanner. The
scanner has read the symbol when:
"
"
"
You hear a beep.
The orange light turns green.
The laser turns off.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
Figure 2-1. Holding the Scanner
Aiming the Scanner
Hold the scanner at an angle. Do not hold the scanner directly over the bar code. Laser light
reflecting directly back into the scanner from the bar code is known as specular reflection.
This strong light can “blind” the scanner and make decoding difficult. The area where
specular reflection occurs is known as a “dead zone”.
You can tilt the scanner up to 55° forward or back and achieve a successful decode. Simple
practice quickly shows what tolerances to work within.
Figure 2-1. Aim ing the Scanner
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning with the LS 2100
!
Scan the Entire Symbol
"
The scan beam must cross every bar and space on the symbol (as in the left bar
code below).
"
"
The larger the symbol, the farther away you should hold the scanner.
Hold the scanner closer for symbols with bars that are close together.
Right
Wrong
W hat Does The Beep Mean?
When you hear 1 beep (short high tone) it means data has been decoded successfully. If any
other beeps are heard, contact the technical person in charge of scanning.
When the symbol has been decoded, you will hear a short, high-tone beep, and the green
decode LED will light.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Maintenance and Specifications
Introduction
This chapter covers the appropriate methods for maintaining and the technical specifications
for the scanner.
Maintenance
Cleaning the exit window is the only maintenance required. A dirty window may affect
scanning accuracy.
!
!
!
!
!
Do not allow any abrasive material to touch the window.
Remove any dirt particles with a damp cloth.
Wipe the window using a tissue moistened with ammonia/water.
Do not spray water or other cleaning liquids directly into the window.
Do not remove the nose of the scanner.
Troubleshooting
If, after following the operating instructions, the scanner does not work:
!
!
Check the system power.
Make sure the controller is programmed to decode bar codes of the symbology you
are scanning.
!
Check for loose cable connections.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
!
!
Make sure the symbol is not defaced.
Try scanning test symbols of the same code type.
If after performing these checks the symbol still does not scan, contact your distributor or call
the Symbol Support Center. See page vi for the telephone number.
Accessories
Standard Accessories:
Description
Part Number
70-32817-xx
70-32818-01
LS 21xx Series Quick Reference Guide
LS 2100 Undecoded Scanner Product
Reference Guide
Shipping Box
50-01400-184
Cables
Description
Part Number
Standard (9-pin D Connector - Female) Straight Cable
Coil Cable for PDT 3300 (9-pin D Connector)
RJ-41 Connector for PDT 1510
25-06751-01
25-05611-03
25-06859-01
Coil Cable for UDI Portable Data Terminals (DB-9 Female Connector) 25-08185-01
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Specifications
Optional Accessories
Optional accessories, supplied at extra cost, include additional units of any item listed above
and the following items:
Description
Part Number
21-33324-01
Hands-free Stand-Free
Standing
Desk-mount Stand
21-33323-01
Technical Specifications
Item
Power Requirements
Decode Capability
Description
4.75 to 14 VDC; 99 mA @ 5 VDC Typical
Determined by interface controller
Decode Depth of Field
Maximum typical working distance is 11 in. (100%
UPC/EAN); minimum element width resolution is 5.5
mils
Scan Repetition Rate
Roll Tolerance
Approximately 36 scans/sec (bidirectional)
± 55° min. (from normal)
Pitch Tolerance
± 50° (from normal)
Yaw Tolerance
± 35° min (from normal)
Print Contrast Minimum
20% minimum reflectance differential, measured at
675 nm.
Ambient Light Immunity
Immune to direct exposure to normal office and
factory lighting conditions, as well as direct exposure
to sunlight.
Durability
5 ft (152 cm) drops to concrete
32° to 104°F (0° to 40°C)
-40° to 140° (-40° to 60°C)
6 ft (183 cm)
Operating Temperature
Storage Temperature
Straight Cable Length
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
Item
Description
Weight (without cable)
5.5 oz. (170 gm)
Dimensions:
Height
6.7 in (167 mm)
2.8 in (70 mm)
3.4 in (85 mm)
Width
Depth
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Specifications
LS 2100 Signal Descriptions
The following signal descriptions apply to the connection between the scanner and the cable,
and are for reference only.
Pin
Signal Name
Power
Function
2
This pin is to be connected to the 4.75 to 14 V (4.75 to 14
VDC) power supply. When pin 4 is high, current to operate
the scanner is supplied by pin 1,2 (99 mA @ 5 VDC).
When pin 4 is at ground potential, current into pin 1 and
2 is less than 50 µA.
3
4
Ground
Enable
Power supply and signal ground return line.
When the decode logic senses that the trigger has been
pulled, this input must be driven high (+2.4 to +14 V into
a 10 kilohm load) to power-up the scanner electronics and
turn on the laser and resonating harmonic scan element.
As soon as a decode is successfully completed, if no decode
occurs after about 1 second, or when the trigger is
released, this input should float or be driven to ground
(less than 0.4 V) to power-down the scanner.
5
Start of Scan
This output synchronizes the decode logic with the
scanner. The output is high when the beam sweeps in one
direction and low when it sweeps in the opposite direction.
This open collector signal is capable of sinking 25 mA. An
external pullup resistor may be connected to any voltage
up to 20 V. The frequency of scans is 36 scans/sec.
6
7
Trigger Switch
Decode LED
This output is grounded when the trigger is pulled and
floating when the trigger is released. The decode logic uses
this switch to signal that the operator wishes to read a bar
code.
This input to the scanner controls the green decode
indicator LED and sounds the beeper. Applying a voltage
of 2.5 V or greater will light the LED. Maximum voltage
that can be applied to this input is 15V. This current
decreases as the voltage is lowered. The decode LED can
be activated with this input even when the scanner is not
operating, providing power is present at pin 2.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
Pin
Signal Name
Function
8
Digitized Bar Pattern Output from the scanner is electrically identical to pin 5,
providing a series of pulses with widths proportional to the
widths of the bar code elements being scanned. A low
output represents a bar, and a high output represents a
space. The frequency of the pulses depends on the density
of the symbol being scanned.
.
PIN 10
PIN 1
Figure 3-1. 10-pin Connector
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Aperture
ASCII
The opening in an optical system defined by a lens or baffle that
establishes the field of view.
American Standard Code for Information Interchange. A 7 bit-plus-
parity code representing 128 letters, numerals, punctuation marks,
and control characters. It is a standard data transmission code in the
U.S.
Autodiscrimination The ability of an interface controller to determine the code type of a
scanned bar code. After this determination is made, the information
content can be decoded.
Bar
The dark element in a printed bar code symbol.
Bar Code Density
The number of characters represented per unit of measurement
(e.g., characters per inch).
Bar Height
Bar Width
The dimension of a bar measured perpendicular to the bar width.
Thickness of a bar measured from the edge closest to the symbol start
character to the trailing edge of the same bar.
Baud Rate
A measure of the data flow or number of signaling events occurring
per second. When one bit is the standard "event," this is a measure of
bits per second (bps). For example, a baud rate of 50 means
transmission of 50 bits of data per second.
Bit
Binary digit. One bit is the basic unit of binary information. Generally,
eight consecutive bits compose one byte of data. The pattern of 0 and
1 values within the byte determines its meaning.
Glossary-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
Byte
On an addressable boundary, eight adjacent binary digits (0 and 1)
combined in a pattern to represent a specific character or numeric
value. Bits are numbered from the right, 0 through 7, with bit 0 the
low-order bit. One byte in memory can be used to store one ASCII
character.
CDRH
Center for Devices and Radiological Health. A federal agency
responsible for regulating laser product safety. This agency specifies
various laser operation classes based on power output during
operation.
CDRH Class 1
This is the lowest power CDRH laser classification. This class is
considered intrinsically safe, even if all laser output were directed into
the eye's pupil. There are no special operating procedures for this
class.
CDRH Class 2
Character
No additional software mechanisms are needed to conform to this
limit. Laser operation in this class poses no danger for unintentional
direct human exposure.
A pattern of bars and spaces which either directly represents data or
indicates a control function, such as a number, letter, punctuation
mark, or communications control contained in a message.
Character Set
Check Digit
Those characters available for encodation in a particular bar code
symbology.
A digit used to verify a correct symbol decode. The scanner inserts the
decoded data into an arithmetic formula and checks that the resulting
number matches the encoded check digit. Check digits are required
for UPC but are optional for other symbologies. Using check digits
decreases the chance of substitution errors when a symbol is decoded.
Codabar
Code 128
A discrete self-checking code with a character set consisting of digits
0 to 9 and six additional characters: ( - $ : / , +).
A high density symbology which allows the controller to encode all
128 ASCII characters without adding extra symbol elements.
Code 3 of 9 (Code 39) A versatile and widely used alphanumeric bar code symbology with
a set of 43 character types, including all uppercase letters, numerals
from 0 to 9, and 7 special characters (- . / + % $ and space). The code
name is derived from the fact that 3 of 9 elements representing a
character are wide, while the remaining 6 are narrow.
Code 93
An industrial symbology compatible with Code 39 but offering a full
character ASCII set and a higher coding density than Code 39.
Glossary-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Code Length
Number of data characters in a bar code between the start and stop
characters, not including those characters.
Continuous Code
A bar code or symbol in which all spaces within the symbol are parts
of characters. There are no intercharacter gaps in a continuous code.
The absence of gaps allows for greater information density.
Dead Zone
An area within a scanner's field of view, in which specular reflection
may prevent a successful decode.
Decode
To recognize a bar code symbology (e.g., UPC/ EAN) and then
analyze the content of the specific bar code scanned.
Decode Algorithm
A decoding scheme that converts pulse widths into data
representation of the letters or numbers encoded within a bar code
symbol.
Depth of Field
Discrete Code
Discrete 2 of 5
The range between minimum and maximum distances at which a
scanner can read a symbol with a certain minimum element width.
A bar code or symbol in which the spaces between characters
(intercharacter gaps) are not part of the code.
A binary bar code symbology representing each character by a group
of five bars, two of which are wide. The location of wide bars in the
group determines which character is encoded; spaces are
insignificant. Only numeric characters (0 to 9) and START/ STOP
characters may be encoded.
EAN
European Article Number. This European/ International version of
the UPC provides its own coding format and symbology standards.
Element dimensions are specified metrically. EAN is used primarily
in retail.
Element
Generic term for a bar or space.
Encoded Area
Total linear dimension occupied by all characters of a code pattern,
including start/ stop characters and data.
Host Computer
IEC
A computer that serves other terminals in a network, providing such
services as computation, database access, supervisory programs, and
network control.
International Electrotechnical Commission. This international agency
regulates laser safety by specifying various laser operation classes
based on power output during operation.
Glossary-3
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
IEC (825) Class 1
This is the lowest power IEC laser classification. Conformity is
ensured through a software restriction of 120 seconds of laser
operation within any 1000 second window and an automatic laser
shutdown if the scanner's oscillating mirror fails.
Intercharacter Gap
The space between two adjacent bar code characters in a discrete
code.
Interleaved Bar Code A bar code in which characters are paired together, using bars to
represent the first character and the intervening spaces to represent
the second.
Interleaved 2 of 5
A binary bar code symbology representing character pairs in groups
of five bars and five interleaved spaces. Interleaving provides for
greater information density. The location of wide elements (bar/
spaces) within each group determines which characters are encoded.
This continuous code type uses no intercharacter spaces. Only
numeric (0 to 9) and START/ STOP characters may be encoded.
LASER - Light
Amplification by
The laser is an intense light source. Light from a laser is all the same
frequency, unlike the output of an incandescent bulb. Laser light is
Stimulated Emission typically coherent and has a high energy density.
of Radiation
Laser Diode
A gallium-arsenide semiconductor type of laser connected to a power
source to generate a laser beam. This laser type is a compact source of
coherent light.
LED Indicator
A semiconductor diode (LED - Light Emitting Diode) used as an
indicator, often in digital displays. The semiconductor uses applied
voltage to produce light of a certain frequency determined by the
semiconductor's particular chemical composition.
MIL
1 mil = 1 thousandth of an inch.
Misread
(Misdecode)
A condition which occurs when the data output of a reader or
interface controller does not agree with the data encoded within a bar
code symbol.
Nominal
The exact (or ideal) intended value for a specified parameter.
Tolerances are specified as positive and negative deviations from this
value.
Nominal Size
Parameter
Standard size for a bar code symbol. Most UPC/ EAN codes can be
used over a range of magnifications (e.g., from 0.80 to 2.00 of
nominal).
A variable that can have different values assigned to it.
Glossary-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Percent Decode
The average probability that a single scan of a bar code would result
in a successful decode. In a well-designed bar code scanning system,
that probability should approach near 100%.
Print Contrast Signal Measurement of the contrast (brightness difference) between the bars
(PCS)
and spaces of a symbol. A minimum PCS value is needed for a bar
code symbol to be scannable. PCS = (RL - RD) / RL, where RL is the
reflectance factor of the background and RD the reflectance factor of
the dark bars.
Programming Mode The state in which a scanner is configured for parameter values. See
SCANNING MODE.
Quiet Zone
A clear space, containing no dark marks, which precedes the start
character of a bar code symbol and follows the stop character.
Reflectance
Resolution
Amount of light returned from an illuminated surface.
The narrowest element dimension which can be distinguished by a
particular reading device or printed with a particular device or
method.
Scan Area
Scanner
Area intended to contain a symbol.
An electronic device used to scan bar code symbols and produce a
digitized pattern that corresponds to the bars and spaces of the
symbol. Its three main components are:
1. Light source (laser or photoelectric cell) - illuminates a bar code.
2. Photodetector - registers the difference in reflected light (more light
reflected from spaces).
3. Signal conditioning circuit - transforms optical detector output into
a digitized bar pattern.
Scanning Mode
The scanner is energized, programmed, and ready to read a bar code.
Scanning Sequence A method of programming or configuring parameters for a bar code
reading system by scanning bar code menus.
Self-Checking Code A symbology that uses a checking algorithm to detect encoding errors
within the characters of a bar code symbol.
Space
The lighter element of a bar code formed by the background between
bars.
Specular Reflection The mirror-like reflection of light from a surface, which can “blind” a
scanner.
Glossary-5
Download from Www.Somanuals.com. All Manuals Search And Download.
LS 2100 Product Reference Guide
Start/Stop Character A pattern of bars and spaces that provides the scanner with start and
stop reading instructions and scanning direction. The start and stop
characters are normally to the left and right margins of a horizontal
code.
Substrate
Symbol
A foundation material on which a substance or image is placed.
A scannable unit that encodes data within the conventions of a certain
symbology, usually including start/ stop characters, quiet zones, data
characters, and check characters.
Symbol Aspect Ratio The ratio of symbol height to symbol width.
Symbol Height
The distance between the outside edges of the quiet zones of the first
row and the last row.
Symbol Length
Length of symbol measured from the beginning of the quiet zone
(margin) adjacent to the start character to the end of the quiet zone
(margin) adjacent to a stop character.
Symbology
The structural rules and conventions for representing data within a
particular bar code type (e.g. UPC/ EAN, Code 39).
Tolerance
UPC
Allowable deviation from the nominal bar or space width.
Universal Product Code. A relatively complex numeric symbology.
Each character consists of two bars and two spaces, each of which can
be any of four widths. The standard symbology for retail food
packages in the United States.
Visible Laser Diode A solid state device which produces visible laser light. Laser light
(VLD)
emitted from the diode has a wavelength of 670 to 680 nanometers.
Glossary-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Tell Us Wh a t You Th in k ...
We’d like to know what you think about this manual. Please take a moment to fill
out this questionnaire and fax this form to: (516) 738-3318, or mail to:
Symbol Technologies, Inc.
One Symbol Plaza M/ S B-4
Holtsville, NY 11742-1300
Attn: Technical Publications Manager
IMPORTANT: If you need product support, please call the appropriate customer
support number provided. Unfortunately, we cannot provide customer support at
the fax number above.
User ’s Manual Title:__________________________________________________
__________________________________________ (please include revision level)
How familiar were you with this product before using this manual?
Very familiar
Slightly familiar
Not at all familiar
Did this manual meet your needs? If not, please explain. __________________
____________________________________________________________________
____________________________________________________________________
What topics need to be added to the index, if applicable?__________________
____________________________________________________________________
What topics do you feel need to be better discussed? Please be specific. _____
____________________________________________________________________
____________________________________________________________________
What can we do to further improve our manuals? ________________________
____________________________________________________________________
____________________________________________________________________
Thank you for your input—We value your comments.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|