Sylvania TV VCR Combo SRCD223B User Manual

OWNER’S

MANUAL

COLOR TV/DVD/VCR TRIPLE COMBO

(23 inch)

(27 inch)

SRCD223B

SRCD227B

27” MODEL ILLUSTRATED

SUPPLIED ACCESSORIES

This Owner’s Manual is

made of recycled paper.

ACCESSORIES

PART NO.

Remote Control Unit NE204UD

Batteries

2 AA Batteries

0EMN02178

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

Owner’s Manual

As an ENERGY STAR^®

Partner, our company has

If you need additional operating assistance after reading this owner’s

manual, please call

TOLL FREE : 1-800-968-3429.

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

Download from Www.Somanuals.com. All Manuals Search And Download.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/DVD/VCR, be sure

the antenna or cable system is grounded so as to provide

some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/DVD/VCR

from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/DVD/VCR.

c. If the TV/DVD/VCR has been exposed to rain or water.

d. If the TV/DVD/VCR does not operate normally by follow-

ing the operating instructions. Adjust only those controls

that are covered by the operating instructions, as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the TV/DVD/VCR to its normal operation.

14.Lightning-For added protection for this TV/DVD/VCR

receiver during a lightning storm, or when it is left unat-

tended and unused for long periods of time, unplug it from

the wall outlet and disconnect the antenna or cable system.

This will prevent damage to the TV/DVD/VCR due to

lightning and power-line surges.

e. If the TV/DVD/VCR has been dropped or damaged in any

way.

f. When the TV/DVD/VCR exhibits a distinct change in per-

formance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

16.Overloading-Do not overload wall outlets and extension

21.Safety Check-Upon completion of any service or repairs to

this TV/DVD/VCR, ask the service technician to perform

routine safety checks to determine that the TV/DVD/VCR

is in proper operating condition.

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/DVD/VCR through openings as they may

touch dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the TV/DVD/VCR.

22.Heat-This TV/DVD/VCR product should be situated away

from heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/DVD/VCR

yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

_{Download from Www.Somanuals.c}-_om3_.-_{All Manuals Search And Download.}

1B15

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

- 4 -

1B15

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a TV/DVD/

VCR which has moisture, it may damage the DVD

and TV/DVD/VCR. Therefore when the condensation

occurs inside the unit, turn the POWER on and allow

at least 2 hours for the unit to dry out.

For safe operation and satisfactory performance of

your TV/DVD/VCR, keep the following in mind

when selecting a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top and bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/DVD/VCR near strong magnetic

fields.

•

TV/VCR

: Description refers to TV/VCR operation (in the

TV/VCR mode).

Avoid moving TV/DVD/VCR to locations where

temperature differences are extreme.

•

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to playback of audio CDs

(in the DVD mode).

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

MP3

: Description refers to playback of MP3 discs

(in the DVD mode).

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/DVD/VCR disc loading tray.

•

QUICK

•

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

Do not place anything directly on top of the unit.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The serial number of this product may be found on the back of the unit. No other TV/DVD/VCR has the same

serial number as yours. You should record the number and other vital information here and retain this book as

a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals.c}-_om5_.-_{All Manuals Search And Download.}

1C29

TABLE OF CONTENTS

SLOW FORWARD / SLOW

REVERSE . . . . . . . . . . . . . . . . . . . .38

C IMPORTANT SAFEGUARDS . . .2, 3

C PLAYBACK . . . . . . . . . . . . . . . . . . .26

NORMAL PLAYBACK . . . . . . . . .26

TRACKING ADJUSTMENT . . . . .26

SLOW MOTION . . . . . . . . . . . . . .26

PICTURE SEARCH . . . . . . . . . . . .26

STILL PICTURE . . . . . . . . . . . . . .26

VERTICAL HOLD CONTROL . . .26

C PRECAUTIONS . . . . . . . . . . . . . . . .4

ZOOM . . . . . . . . . . . . . . . . . . . . . .38

LOCATION . . . . . . . . . . . . . . . . . . .5

C SEARCH FUNCTION . . . . . . . . . . .39

TRACK SEARCH . . . . . . . . . . . . .39

TITLE / CHAPTER SEARCH . . . .39

TIME SEARCH . . . . . . . . . . . . . . .39

MARKER SETUP SCREEN . . . . . .39

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C SPECIAL PLAYBACK . . . . . . . . . .27

C TABLE OF CONTENTS . . . . . . . . . .6

RENTAL PLAYBACK . . . . . . . . . .27

AUTO REPEAT PLAYBACK . . . . .27

SPECIAL PLAYBACK FUNCTION . . .40

REPEAT . . . . . . . . . . . . . . . . . . . . .40

PROGRAM . . . . . . . . . . . . . . . . . . .40

RANDOM PLAYBACK . . . . . . . . .40

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C SEARCH . . . . . . . . . . . . . . . . . . . . .28

ZERO RETURN . . . . . . . . . . . . . . .28

TIME SEARCH . . . . . . . . . . . . . . .28

INDEX SEARCH . . . . . . . . . . . . . .29

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . .9, 10

C PLAYING A MP3 DISC . . . . . . . . . .41

MP3 PLAYBACK . . . . . . . . . . . . . .41

TRACK SELECTION . . . . . . . . . . .41

PROGRAM . . . . . . . . . . . . . . . . . . .41

RANDOM PLAYBACK . . . . . . . . .41

C PREPARATION FOR USE . . . . . . .11

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .11

C SPECIAL FEATURES . . . . . . . . . .29

REAL TIME TAPE COUNTER . . .29

AUTO REWIND-EJECT . . . . . . . .29

CONNECTING TO EXTERNAL

INPUT JACKS . . . . . . . . . . . . . . . .12

INSTALLING THE BATTERIES . .12

EXTERNAL INPUT MODE . . . . . .12

C CHANGING THE SETTINGS . . . .42

SUBTITLE LANGUAGE . . . . . . . .42

AUDIO LANGUAGE . . . . . . . . . . .42

STEREO SOUND MODE . . . . . . . .42

CAMERA ANGLE . . . . . . . . . . . . .42

BLACK LEVEL SETTING . . . . . . .42

VIRTUAL SURROUND . . . . . . . . .42

C RECORDING . . . . . . . . . . . . . . . . .30

NORMAL RECORDING . . . . . . . .30

CONNECTING TO A STEREO

SYSTEM . . . . . . . . . . . . . . . . . . . .13

SKIPPING UNWANTED SCENES

DURING RECORDING . . . . . . . . .30

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD

DECK OR DAT DECK . . . . . . . . . .13

OTR (One Touch Recording) . . . . . .31

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .31

CONNECTING TO A RECEIVER

WITH DOLBY DIGITAL

DECODER . . . . . . . . . . . . . . . . . . .14

C TIMER . . . . . . . . . . . . . . . . . . . . . .32

THE ON-SCREEN INFORMATION . . .43

AUTOMATIC

TIMER RECORDING . . . . . . . . . .32

C CHANGING THE DVD SETUP

TV/VCR SECTION

ITEMS . . . . . . . . . . . . . . . . . . . . . . .44

TIMER PROGRAM EXTENSION .33

C SET UP FOR USE . . . . . . . . . . . . .15

LANGUAGE SETTING . . . . . . . . .44

DISPLAY SETTING . . . . . . . . . . . .45

AUDIO SETTINGS . . . . . . . . . . . .45

PARENTAL CONTROL . . . . . . . . .46

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . .34

CHANNEL SET UP

FOR THE FIRST TIME . . . . . . . . .15

AUTO RETURN . . . . . . . . . . . . . . .34

SLEEP TIMER . . . . . . . . . . . . . . . .34

DELETING (OR ADDING)

CHANNEL . . . . . . . . . . . . . . . . . . .15

C TROUBLESHOOTING GUIDE . . .47

CHANNEL SET UP AGAIN . . . . . .16

SELECTING THE LANGUAGE . .16

DAYLIGHT-SAVING TIME . . . . . .16

C ON SCREEN DISPLAY . . . . . . . . .35

C MAINTENANCE . . . . . . . . . . . . . . .50

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .35

DISC HANDLING . . . . . . . . . . . . .50

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . .17, 18

DVD SECTION

C SPECIFICATIONS . . . . . . . . . . . . .51

C WARRANTY . . . . . . . . . . .Back Cover

C TV OPERATION . . . . . . . . . . . . . . .19

WATCHING A TV PROGRAM . . .19

DEGAUSSING . . . . . . . . . . . . . . . .19

PICTURE CONTROL . . . . . . . . . . .19

CLOSED CAPTION SYSTEM . . . .20

V-CHIP SET UP . . . . . . . . . . . . . . .21

C ABOUT THE DISCS . . . . . . . . . . . .36

PLAYABLE DISCS . . . . . . . . . . . .36

DISC TYPES . . . . . . . . . . . . . . . . .36

C PLAYING A DISC . . . . . . . . . . . . . .37

BASIC PLAYBACK . . . . . . . . . . . .37

GENERAL FEATURES . . . . . . . . .37

DISC MENU . . . . . . . . . . . . . . . . .37

TITLE MENU . . . . . . . . . . . . . . . . .37

RESUME . . . . . . . . . . . . . . . . . . . .38

PAUSE . . . . . . . . . . . . . . . . . . . . . .38

STEP BY STEP PLAYBACK . . . . .38

C MTS(Multi-Channel Television

sound)SYSTEM . . . . . . . . . . . . . . . .23

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .23

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .23

FAST FORWARD/REVERSE

SEARCH . . . . . . . . . . . . . . . . . . . .38

SELECTING THE MTS SYSTEM .24

C VIDEO CASSETTE . . . . . . . . . . . . .25

- 6 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV/VCR Mode

Hi-Fi system–The Hi-Fi stereo recording system

offers you excellent sound quality with a dynamic

range of 80dB, frequency response from 20Hz to

20kHz, and 0.005% wow and flutter.

Rotary 4-head Record/Playback System–Four heads

ensure excellent picture quality and special effects playback.

Index Search–Fast-forwards to start of next recording.

Slow Motion–View recorded program at slower

than normal speed.

Infrared remote control

Trilingual on screen tv/vcr setup display selec-

table in English or Spanish or French

Real time counter–This shows the elapsed recording

or playback time in hours, minutes, and seconds. The

“–” indication will appear when the tape is rewound

further than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Auto power on and off system–Automatically

turns on the TV/DVD/VCR when you insert the

cassette, turns off after auto-rewind, and ejects

when the beginning of the tape is reached.

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

Still–“Freeze” the picture at any time, for close

viewing of a particular scene.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Let you set the TV/DVD/VCR to

advance the tape by entering the desired playback

time you want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts, and the Weekly timer allows recording to be

made once a week up to the end of the tape.

•

Auto return–After timer recording is finished, the

TV/DVD/VCR can return to the beginning of the

recording.

Sleep timer–Allows you to have the TV/DVD/VCR

automatically turn on or off at a desired time.

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

Smooth mode change–TV/VCR mode, DVD

mode automatically changes.

•

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

_{Download from Www.Somanuals.c}-_om7_.-_{All Manuals Search And Download.}

1C29

DVD Mode

¡On-screen display

¡Dolby Digital sound

This player can a Dolby Digital signal having 5.1

channels when connected to a Dolby Digital

decoder.

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Still/fast/slow/step playback

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

¡Search

Chapter search / Title search / Track search / Time

¡Repeat

¡Random playback for audio CD and MP3

This player can shuffle the order of tracks to play

them in random order.

Chapter / Title / Track / Group / All / A-B

¡Zoom

Magnified screen can be displayed.

¡Program playback for audio CD and MP3

You can program the order of tracks to play them in

any desired order.

¡Marker

The part designated by user can be called back.

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Virtual Surround

¡Bit rate indication

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no

input from the player for five minutes in the stop

mode. When the screen saver program is activated

for 15 minutes, the power automatically turns off.

¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available

on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This player automatically detects if the loaded disc is

DVD, audio CD or MP3 on disc.

¡Playback MP3 disc

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code num-

ber given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal

remote control.

- 8 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- TV/DVD/VCR FRONT PANEL - [Fig.1]

DVD buttons

TV/VCR buttons

F.FWD

PLAY

REW

REC/OTR

HEADPHONE

VIDEO

AUDIO

STOP/EJECT

POWER

OPEN/CLOSE

SELECT

VOLUME

SKIP

PLAY

SKIP

CHANNEL

STOP

DVD

TV/VCR

3 4 3

7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21

5.STOP Button [TV/VCR P.26 / DVD P.37]

Stops operation of the disc. (main unit)

Stops operation of the disc or tape contents.

(remote control)

[Fig. 2]

- REMOTE CONTROL -

6.OPEN/CLOSE Button [DVD P.37]

Press to open disc tray to insert a disc or to open

to remove a disc.

7.Disc loading tray

8.DVD Indicator

Lights on during DVD mode.

POWER PICTURE SLEEP SELECT

CH.

PAUSE

+100

VOL.

9.SELECT Button

+10

Press to change to TV/VCR mode, external input

mode or DVD mode.

SPEED C.RESET

ZOOM

MUTE

10.TV/VCR Indicator

PLAY

STOP

Lights on during TV/VCR mode.

3 (DVD)

15 (TV/VCR)

(DVD) 3

^(TV/VCR)4¹⁴

11. CHANNEL K/L Buttons

DISC

Press to select memorized channel.

RECORD

12. Recording Indicator

DISPLAY

SETUP

ENTER

Flashes during recording. Lights up in the Stand-

by mode for Timer Recording.

TITLE

RETURN

CLEAR SEARCH MODE REPEAT

A-B

13. REC/OTR (RECORD)Button [TV/VCR P.30, 31]

Press for manual recording. Activates One Touch

Recording. (OTR is only during TV/VCR mode.)

14. REW Button (for VCR) [TV/VCR P.26]

Press to rewind the tape, or to view the picture

rapidly in reverse during playback mode. (Rewind

Search)

AUDIO SUBTITLE ANGLE

MODE

15. FWD Button (for VCR) [TV/VCR P.26]

Press to rapidly advance the tape, or to view the

picture rapidly in forward during playback mode.

(Forward Search)

16. STOP/EJECT Button (for VCR) [TV/VCR P.28]

Press to stop the tape motion. Press in the Stop

mode to remove tape from the TV/VCR/DVD.

1.POWER Button [TV/VCR P.15 / DVD P.37]

Press to turn the power on and off.

2.VOLUME X/Y Buttons

Press to control the volume level for the DVD and TV.

3.SKIP Buttons (for DVD) [P.38]

Press once to skip chapters or tracks to a desired

point.

Press and hold to change forward or reverse play-

back speed.

4.PLAY Button [TV/VCR P.26 / DVD P.37]

Starts playback of the disc or tape contents.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

19. VIDEO input Jack

Connect to the video output jack of a video

camera or VCR, video game.

_{Download from Www.Somanuals.c}-_om9_.-_{All Manuals Search And Download.}

1C29

- TV/DVD/VCR REAR PANEL - [Fig.3]

ANT.

AUDIO OUT

COAXIAL

48 49

20. AUDIO L/R input Jacks

31. MODE Button [DVD P.41]

Connect to the audio output jacks of a video

camera or VCR, video game.

Activates program playback or random playback mode.

32. SEARCH MODE Button [DVD P.39]

21. Video Cassette compartment

Press to locate a desired point.

22. PICTURE Button

33. AUDIO Button [DVD P.42]

Press to select a desired audio language or sound

mode.

Press to adjust the picture.

23. Number Buttons

34. SUBTITLE Button [DVD P.42]

TV Mode:[P.15]

Press two digits to directly access the desired

channel.

Remember to press a "0" before a single digit

channel.

+100 Button–

Press to select cable channels which are equal or

greater than number 100.

DVD Mode: [P.39]

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are

equal or greater than number 10.

Press to select a desired subtitle language.

35. REPEAT Button [DVD P.40]

Repeats playback of the current disc, title, chapter

or track.

36. ANGLE Button (DVD mode) [DVD P.42]

Press to change the camera angle to see the

sequence being played back from a different angle.

37. A-B REPEAT Button [DVD P.40]

Repeats playback of a selected section.

38. RETURN Button [TV/VCR P.15 / DVD P.39]

Returns to the previous operation in the DVD

setup mode.

24. PAUSE Button [TV/VCR P.26 / DVD P.38]

39. ENTER Button [TV/VCR P.15 / DVD P.37]

Pauses the current disc or tape operation.

Press to accept a setting.

25. SPEED Button [TV/VCR P.30]

Press to choose the desired recording speed:

SP/SLP.

26. C.RESET Button [TV/VCR P.28]

Press to reset counter to 0:00:00.

Press to cancel a setting of timer program. (See

page 33.)

40. Arrow Buttons

TV/VCR Mode: [P.15]

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode: [P.37]

Use when making settings while watching the

display on a TV screen.

27. DISPLAY Button

TV/VCR Mode: [P.23]

41. DISC MENU Button [DVD P.37]

Display the counter or the current channel number

and current time on the TV screen.

DVD Mode:[P.43]

Displays the current status on the TV screen for

checking purposes.

Displays the menus in the DVD.

42. ZOOM Button [DVD P.38]

Enlarges part of a DVD-reproduced image.

43. MUTE Button [P.20]

Mutes the sound. Press it again to resume sound.

28. SETUP Button [TV/VCR P.15] [DVD P.44-46]

Press to enter or exit the TV menu or DVD setup

mode.

44. SLEEP Button [TV/VCR P.34]

Sets the Sleep Timer.

45. SELECT Button [TV/VCR P.26 / DVD P.37]

Press to switch TV/VCR and DVD mode. You can

see the mode (TV/VCR or DVD) on the front

panel indicator.

29. TITLE Button [DVD P.37]

Displays the title menu.

30. CLEAR Button [P.39]

Resets a setting.

- 10 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

46. ANT. in Jack

48. COAXIAL digital audio out Jack

Connect to the digital input of an external

amplifier or decoder for DVD audio only.

Connect to an antenna, cable system, or satellite

system.

47. Power cord

49. AUDIO L/R analog output Jack

Connect to the analog audio input of an external

amplifier or stereo system.

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect

to a standard AC outlet.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box (Not supplied)

OUT

From Cable System or

Satellite Dish

VHF Antenna (Not supplied)

75-ohm

Coaxial

Cable

UHF Antenna

(Not supplied)

From Cable

System

(Not sup-

plied)

ANT.

AUDIO OUT

VHF/UHF

COAXIAL

Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not

[Fig. 4]

supplied)

Flat twin-lead cable

VHF/UHF SEPARATE ANTENNAS

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

In some areas it will be necessary to use an outdoor

antenna.

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the illustration.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/DVD/VCR Remote Control. Unattended timer

recording is limited to one channel at a time.

Use this connection if your cable system connects

directly to your TV/DVD/VCR without a converter

box.

By using this connection you can:

1) Use the TV/DVD/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

Antenna/Cable Connections

Continued on the Next Page.

NOTE: This TV/VCR/DVD will ONLY record and

view the same channel.

- 11 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO RECORD A SCRAMBLED/UNSCRAM-

BLED CHANNEL

INSTALLING THE BATTERIES

1. Set the TV/DVD/VCR channel selector to the out-

put channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

Note to CATV system installer:

3)Replace the cover.

This reminder is provided to call the CATV sys-

tem installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper ground-

ing and, in particular, specifies that the cable

ground shall be connected to the grounding sys-

tem of the building as close to the point of cable

entry as practical.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO L/R IN/

CONNECTING TO EXTERNAL

INPUT JACKS

When you watch a program recorded on an another

source (VCR or video camera), use the audio/video

input jacks on the front of the TV/DVD/VCR.

Connect the audio/video output jacks of another

source to the AUDIO L/R and VIDEO jacks of this

TV/DVD/VCR.

AUX

VIDEO IN jacks of your

TV/DVD/VCR. Then press the

CHANNEL button K or L until

“AUX” appears on the screen.

Then press the CHANNEL buttons K/L until "AUX"

appears on the screen.

NOTE:

When you connect a monaural VCR (another

•

source) to this TV/DVD/VCR, connect the Audio

output jack of the monaural VCR (another source)

to the AUDIO L jack of this TV/DVD/VCR. The

audio will output in both L and R channel equally.

To the audio

output jacks

[Another source]

HEADPHONE

VIDEO

AUDIO

Audio/Video

coaxial cable

(not supplied)

etc.

To the video

[Front of the

TV/DVD/VCR]

output jack

[Fig. 5]

- 12 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A STEREO SYSTEM

ANT.

AUDIO OUT

Stereo system

COAXIAL

To Right (red) and Left (white)

To ANALOG AUDIO INPUT jacks

AUDIO OUT jacks

[Fig. 6]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for your stereo system and any other components to be connected to the

TV/DVD/VCR.

•

For analog stereo (2-channel) TV-VCR-DVD sound.

•

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK

Use an audio coaxial digital cable available at retail for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

ANT.

AUDIO OUT

COAXIAL

Amplifier equipped with digital

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

input jacks, MD deck,

DAT deck, etc.

To COAXIAL DIGITAL

AUDIO INPUT jack

(only DVD AUDIO OUT)

[Fig. 7]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.

Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect set-

tings may generate noise distortion, and may also damage the speakers.

•

For digital stereo (2-channel) DVD sound only.

•

- 13 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A RECEIVER WITH DOLBY DIGITAL DECODER

If using this TV/DVD/VCR to play a DVD disc, the TV/DVD/VCR outputs DOLBY DIGITAL Data stream

from its COAXIAL digital audio out jack. By hooking the player up to a receiver with Dolby Digital decoder,

you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as

enjoyed in movie theaters.

Use audio coaxial digital cables available at retail for the audio connections.

Center

speaker

ANT.

Front speaker

(left)

Front speaker

(right)

AUDIO OUT

COAXIAL

Receiver with

Dolby Digital

decoder

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 8]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.

If connected to a receiver with Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the

setup mode. (See page 45 to set DOLBY DIGITAL to ON.)

•

Unless connected to a receiver with Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output

in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may

also damage the speakers.

•

Only DVD audio is available using the COAXIAL digital audio out jack.

•

For TV and VCR audio sound, please refer to “CONNECTING TO A STEREO SYSTEM” section on page

13). You will need to use these connection in addition to the above to enjoy TV and VCR sound through the

same receiver.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

- 14 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV/VCR SECTION

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/DVD/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).

Then select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

DELETING (OR ADDING)

CHANNEL

TV/VCR

1 Plug in the TV/DVD/VCR power

cord

Plug the TV/DVD/VCR power cord

into a standard AC outlet.

NOTE:

If some digits appear in the corner of

the screen, press the POWER button without

unplugging the power cord.

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

•

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

remote control.

Press the Arrow button K or L to

point to “CHANNEL SET UP”.

Then, press the ENTER button.

TIME SEARCH

INDEX SEARCH

2 Turn on the TV/DVD/VCR

Press the POWER button to turn on the TV/DVD/VCR.

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press the Arrow button K or L to

point to “ADD/DELETE CH”.

Press the ENTER button.

ADD / DELETE CH (TV)

AUTO PRESET

3 Select “ENGLISH” or “ESPAÑOL” or

– SET UP –

“FRANÇAIS”

LANGUAGE

Select “ENGLISH” or

[ENGLISH] ESP

FRA

“ESPAÑOL”=Spanish or

“FRANÇAIS” =French using the

ENTER button. “[ ]” indicate the

selected language.

AUTO PRESET

3 Enter the desired channel number

Press the Arrow button K or L until

your desired channel number appears.

(You can also use the number buttons

or the CHANNEL buttons K/L to

enter it) (Example: CH8)

4 Begin auto preset

– SET UP –

ADD / DELETE

Press the Arrow button K or L to

point to “AUTO PRESET”.

Then press the ENTER button.

The tuner scans and memorizes all

active channels in your area.

LANGUAGE

[ENGLISH] ESP

FRA

AUTO PRESET

4 Delete (or add) it from (into) memory

Press the ENTER button. The channel number changes

to light red. The channel is deleted from memory.

NOTES:

The TV/DVD/VCR distinguishes between standard

TV channels and cable channels.

If you want to play or record a video tape

BEFORE presetting the tuner, you must press the

SETUP button on the remote control. To preset the

tuner again, see “CHANNEL SET UP AGAIN” on

page 16.

The TV/DVD/VCR may memorize TV channels as

CATV channels if reception conditions is poor. If

this happens, try AUTO MEMO action again when

reception conditions are better.

•

Added channel: Light blue.

Deleted channel: Light red.

•

To delete another channel, repeat steps [3] and [4].

If you press the ENTER button again, the channel

is memorized again.

Press the RETURN button to return to TV/VCR

•

SETUP MENU.

5 Exit the channel setup mode

Press the SETUP button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL button K or L.

5 After scanning

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote con-

trol number buttons or the CHANNEL button K or L.

- 15 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: If Spanish or French is selected accidentally,

1)Press the SETUP button on the remote control.

2)Press the Arrow button K or L to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE” [FRANÇAIS].

3)Press the ENTER button to select your desired lan-

guage.

CHANNEL SET UP AGAIN

TV/VCR

Make sure ...

Press the POWER button to turn on the

TV/DVD/VCR.

•

4)Press the SETUP button to exit.

DAYLIGHT-SAVING TIME

1 Select “CHANNEL SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the SETUP button on the

remote control.

TV/VCR

Select this feature and the TV/DVD/VCR’s clock

automatically will advance one hour in April, then

reverse one hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

Press the Arrow button K or L to

point to “CHANNEL SET UP”.

Then, press the ENTER button.

TIME SEARCH

INDEX SEARCH

2 Begin auto preset

Press the Arrow button K or L to

point to “AUTO PRESET”.

Then, press the ENTER button.

The tuner scans and memorizes all

the active channels in your area.

First Sunday of April : At 2 AM the clock imme-

– CHANNEL SET UP –

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

ADD / DELETE CH (TV)

AUTO PRESET

•

Make sure ...

Press the POWER button to turn on the

TV/DVD/VCR.

3 After scanning

The tuner stops on the lowest memorized channel.

•

- TV/VCR SETUP -

1 Select “SETTING CLOCK”

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the SETUP button on the

remote control.

SELECTING THE LANGUAGE

Press the Arrow button K or L to

point to “SETTING CLOCK.”

Then, press the ENTER button.

TIME SEARCH

INDEX SEARCH

TV/VCR

Make sure ...

Press the POWER button to turn on the

TV/DVD/VCR.

•

2 Set “D.S.T.” (Daylight-Saving

Time) to [ON]

Press the Arrow button K or L to

point to “D.S.T.”

Then, press the ENTER button until

[ON] appears.

– SETTING CLOCK –

NOTE: This function effects only the language on

the screen menu and not the audio source.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[02]

[ON]

- TV/VCR SETUP -

1 Select “LANGUAGE”

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

Press the SETUP button on the

USER’S SET UP

V-CHIP SET UP

remote control.

Press the Arrow button K or L to

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3 Exit the Daylight-Saving Time mode

Press the SETUP button on the remote control to

return to TV mode.

point to “LANGUAGE”.

2 Select “ENGLISH” or “ESPAÑOL” or

“FRANÇAIS”

TO CANCEL THE DAYLIGHT-SAVING

TIME

Select “ENGLISH” or “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the ENTER button.

Repeat steps [1] to [2], select [OFF] using the

ENTER button.

3 Exit the Language mode

Press the SETUP button on the remote control to

return to TV mode.

- 16 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOCK SET UP

(AUTO / MANUAL)

6 Select the hour

Press the Arrow button K or L until

your desired hour appears.

(Example: 5, PM)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 TUE 2 0 0 3

TV/VCR

HOUR

0 5

MINUTE

– – PM

The TV/DVD/VCR clock must be set correctly before

VCR timer recording is possible. It is suggested that the

clock be set manually when first setting up the

TV/DVD/VCR. Then, setup auto clock correction which

will periodically correct the setting if necessary.

NOTE: If you cannot receive a station with time sig-

nals, auto clock setting cannot be performed. Use

manual setting only.

Then, press the Arrow button B.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the Arrow button K or L until

the desired minute appears.

(Example: 40)

0 5

0 6 TUE 2 0 0 3

HOUR

0 5

MINUTE

4 0 PM

MANUAL CLOCK SETTING

Make sure ...

8 Start the clock

Press the SETUP button on the

remote control.

5:40 PM

TV/DVD/VCR power is turned on.

•

Although seconds are not displayed,

they begin counting from 00 when

you press the SETUP button on the

remote control. Use this feature to synchronize the

clock with the correct time.

In the example below, the clock is to be set to:

DATE

May 6th, 2003

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

Press the SETUP button on the

remote control.

NOTE:

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

Press the Arrow button K or L to

point to “SETTING CLOCK”.

Then, press the ENTER button.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the Arrow

button B or s.

3)Enter correct numbers using the Arrow button K or

2 Select “MANUAL CLOCK

SET”

Press the Arrow button K or L to

point to “MANUAL CLOCK SET”.

Then, press the ENTER button.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[02]

[OFF]

4)Press the SETUP button on the remote control to

start the clock.

3 Select the month

Press the Arrow button K or L until

your desired month appears.

(Example: May → 05)

– MANUAL CLOCK SET –

MONTH DAY YEAR

PLEASE NOTE:

0 5

– – – – – – – – –

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the ENTER button to turn [OFF] this function.

Then you can manually adjust the clock.

HOUR

– –

MINUTE

– – – –

Then, press the Arrow button B.

4 Select the day

Press the Arrow button K or L until

your desired day appears.

(Example: 6th → 06)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the Arrow button B.

5 Select the year

Press the Arrow button K or L until

your desired year appears.

(Example: 2003)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 TUE 2 0 0 3

HOUR

– –

MINUTE

– – – –

Then, press the Arrow button B.

- 17 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTOMATIC CLOCK SETTING

- TV/VCR SETUP -

Press the Arrow button K or L to

select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

Press the Arrow button L to select

“AUTO CLOCK CH”.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Make sure ...

The TV/DVD/VCR is turned on.

Confirm the TV/DVD/VCR is receiving a RF

(Radio Frequency) signal from either an antenna or

cable system connection using the ANT IN jack on

the rear of the TV/DVD/VCR.

•

TIME SEARCH

INDEX SEARCH

– SETTING CLOCK –

Press the ENTER button, then

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

NOTE:

press the Arrow button s or

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

[OFF]

If a cable converter box is being used, make sure it

is powered on.

until you locate Auto Clock Set

station number. See item 3 above.

Press the SETUP button to exit the

screen.

•

You must use the TV/DVD/VCR remote control to

perform the clock setting procedure.

•

5 Turn off the TV/DVD/VCR

Once the TV/DVD/VCR is turned off , it will period-

ically check and set the correct date and time.

1 Select “SETTING CLOCK”

Press the SETUP button on the

- TV/VCR SETUP -

TIMER PROGRAMMING

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the Arrow button K or L to

select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

TIME SEARCH

INDEX SEARCH

2 Set “AUTO CLOCK” to [ON]

Press the ENTER button until

AUTO CLOCK [ON] appears.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[02]

[OFF]

3 Begin “AUTO CLOCK CH SEARCH”

Press the Arrow button L to select “AUTO CLOCK

CH SEARCH”.

Press the ENTER button.

– SETTING CLOCK –

The TV/DVD/VCR is now

•

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[02]

searching for the station which

contain the auto clock set signal.

The search for a signal may take

up to 20 seconds per channel.

“_ _” appears at the lower left of

the screen when the search has

ended.

[OFF]

•

– AUTO CLOCK CH SEARCH –

Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

4 below.

•

_ _

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 17.

•

Press the SETUP button to exit the screen.

NOTE: During Auto Clock CH Search, the picture

may be distorted. This is normal.

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the SETUP button on the remote control.

- 18 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

TV/VCR

The TV/DVD/VCR’s picture controls – BRIGHT,

CONTRAST, COLOR, TINT and SHARPNESS –

are preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

1 Turn on the TV/DVD/VCR

Press the POWER button to turn on the

TV/DVD/VCR.

NOTES:

2 Select the channel number

Press the CHANNEL button K or L to select your

desired channel number or press the number on the

remote control.

Note for using the Number button on the remote

control:

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

¡When selecting cable channels which are higher

than 99, press +100 first, then, press the last two

digits. (Example: to select channel 125, first press

“+100” then press “2” and “5”).

¡You must precede single-digit channel numbers

with a zero (For example: 02, 03, 04 and so on).

TV/DVD/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

Press the PICTURE button on the remote control.

Remember: If the TV/DVD/VCR is connected to a

cable box or satellite box, the TV/DVD/VCR must

be on CH3 or CH4, then the channel to be viewed

must be selected on the cable box or satellite box.

2 Select item you want to adjust

Press the Arrow button K or L until desired control

is displayed.

BRIGHT

CONTRAST

COLOR

TINT

3 Adjust sound

Press the VOLUME button or

BRIGHT

–

P +

to adjust the volume.

SHARPNESS

VOLUME 20

3 Adjust the picture control

NOTES:

Press the Arrow button s or B to adjust to your

If you press the CHANNEL button o or p in the

DVD mode, you can change the TV channels.

Even if you turn off the TV/DVD/VCR in the

DVD mode, when you turn it on again, it will go

into the TV/VCR mode.

•

desired level.

Arrow button s Arrow button

BRIGHT

to decrease

brightness

to decrease

contrast

to increase

brightness

to increase

contrast

CONTRAST

DEGAUSSING

COLOR

TINT

to pale

to brilliant

TV/VCR

to purple

to green

to clear

Magnetism from nearby appliances and speakers

might affect the color of the TV picture.

SHARPNESS to soft

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

•

If this happens, move this TV/VCR/DVD away from

the appliance. If the color is still not correct, turn off

using the POWER button, then turn it on again 30

minutes or so later.

- 19 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOSED CAPTION SYSTEM

- TV/VCR SETUP -

1 Select “CAPTION”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “CAPTION”.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

You can view specially labeled (cc) TV programs,

movies, news, pre-recorded tapes with either a dia-

logue caption or text display.

TIME SEARCH

INDEX SEARCH

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

2 Select your desired caption menu

- TV/VCR SETUP -

Press the ENTER button until your

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

desired caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3 Exit the caption setting mode

NOTE:

Press the SETUP button on the remote control to

return to TV mode.

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], select [OFF] using the

ENTER button. Press the SETUP button on the

remote control to return to TV mode.

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

It will also disappear when the MUTE button is

pressed, and when the PAUSE button is pressed

while recording.

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

If the TV/DVD/VCR displays a

black box on the TV screen, this

means that the TV/DVD/VCR is

set to the TEXT mode. To clear

screen, select [CAPTION1], [CAP-

TION2] or [OFF].

•

If there is a power failure of any kind, the

TV/DVD/VCR will retain its memory for this fea-

ture.

•

Make sure ...

TV/DVD/VCR power must be turned on.

•

- 20 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

V-CHIP SET UP SUB RATINGS

When you select the ratings of TV-Y7,TV-PG,TV-14

or TV-MA you will have the option of selecting sub

rating categories.

V-CHIP SET UP

TV/VCR

V-CHIP SET UP

- TV/VCR SETUP -

1 Select “V-CHIP SET UP”

Make sure ...

•

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/DVD/VCR is turned on.

Press the Arrow button K or L to

select “V-CHIP SET UP”. Then,

press the ENTER button.

TIME SEARCH

INDEX SEARCH

1 Select “V-CHIP SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

select “V-CHIP SET UP”.

Then, press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

2 Enter Access code

ACCESS CODE

TIME SEARCH

INDEX SEARCH

Use the number buttons on the

remote control to enter the access

code. (Default code is 0000.)

2 Enter Access code

Use the number buttons on the remote

control to enter the access code.

ACCESS CODE

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

3 Select “TV RATING”

Press the Arrow button K or L to

select “TV RATING”.

For the first time set-up or in the

event the TV/DVD/VCR has lost

•

Then, press the ENTER button.

power, enter the default code of the numbers:

0000.

– V-CHIP SET UP –

4 Selecting Sub-Ratings”

Press the Arrow button L to select the sub-rating you

3 Select “TV RATING”

Press the Arrow button K or L to

select “TV RATING”.

TV RATING

MPAA RATING

CHANGE CODE

wish to block. Then, press the ENTER button twice.

When you select [TV-Y7]:

Press the Arrow button L or K to

•

Then, press the ENTER button.

select “FV” (Fantasy Violence).

Then, press the ENTER button to

select [BLOCK] or [VIEW].

When you select [TV-PG], [TV-

14] or [TV-MA]:

Press the Arrow button L or K to

select “D”(Suggestive Dialog),

“L”(Coarse Language),

“S”(Sexual Situation), or

“V”(Violence). Then, press the

ENTER button to select [BLOCK] or [VIEW].

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

TV–Y7

[BLOCK]

4 Blocking TV programs

Press the Arrow button K or L to

select “TV rating” that you wish to

block.

Press the ENTER button to turn it

[BLOCK].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

(

)

•

(

TV–PG

[BLOCK]

When you select the rating category and turn it

[BLOCK]

•

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “TV-Y” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

The sub-ratings which set to

•

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

Selection

TV-Y

TV-Y7

TV-G

Rating Category Explanations

Appropriate for all children

Appropriate for children seven and older

General Audience

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV rating

menu.

[BLOCK]

TV-PG

TV-14

Parental Guidance suggested.

Unsuitable for children under 14

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

enter the setting and exit the screen.

TV-MA Mature audience only

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

- 21 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING V-CHIP BLOCKED PRO-

GRAMMING

Note: To change the rating, the TV must be turned to

a station that is not protected. If the (PROTECTED)

appears on the screen, please change the channel to a

station that is not protected.

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

1)Follow steps [1] and [2].

CHANGE ACCESS CODE

2)Press the Arrow button K or L to select "TV RAT-

ING". Then, press the ENTER button. Select a TV

rating to be unblocked by pressing the Arrow but-

ton K or L.

Then press the ENTER button to unblock the rating.

3)Press the SETUP button on the remote control to

exit the screen.

To change access code, follow the steps.

1 Select “V-CHIP SET UP”

Press the SETUP button on the remote control.

Press the Arrow button K or L to select “V-CHIP

SET UP”.

Then, press the ENTER button.

MPAA RATING SET UP

2 Enter Access code

ACCESS CODE

- TV/VCR SETUP -

Use the number buttons on the remote

1 Select “V-CHIP SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

select “V-CHIP SET UP”. Then,

press the ENTER button.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

control to enter the access code.

The default code is 0000.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

3 Select “CHANGE CODE”

Press the Arrow button K or L to

select "CHANGE CODE". Then,

press the ENTER button.

2 Enter Access code

Use the number buttons on the

remote control to enter the access

code.

ACCESS CODE

4 Enter New code

NEW CODE

Use the number buttons to enter

your desired access code in the

NEW CODE space. Then enter the

same code in the CONFIRM

CODE space. V-CHIP SET UP

screen appear on the screen.

X X X X

CONFIRM CODE

– V-CHIP SET UP –

TV RATING

MPAA RATING

CHANGE CODE

3 Select “MPAA RATING”

Press the Arrow button K or L to

point to “MPAA RATING”.

Then, press the ENTER button.

If you enter wrong code, repeat step 4, making

sure you enter the same new code exactly in the

confirm code space.

•

4 Select your desired item

Press the Arrow button K or L to

point to your desired item.

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

Then, press the ENTER button to

select [BLOCK] or [VIEW].

5 Exit the V-Chip setting mode

Press the SETUP button on the remote control to

exit the screen.

Selection

Rating Category Explanations

General Audience

Note: If you unplug the power code or power failure

occurs, the changed access code will be lost and will

return to default (0000). Change your access code

again as necessary.

PG-13

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

NC-17

Mature audience only

When you select the rating category and turn it

[BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn

[VIEW] automatically.

When you turn “G” to [VIEW], then all ratings

will turn to [VIEW] automatically.

•

- 22 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

MTS(Multi-Channel Television sound)SYSTEM

You can record or listen to a program in MTS stereo.

CHECKING THE SELECTED MTS MODE

TV/VCR

When you play a VHS tape, or receive a broadcast

on the TV/DVD/VCR tuner channel you are watching,

the status shown below will appear when you press

the DISPLAY button on the remote control.

1] When a program is broadcast in stereo, STEREO

appears on the TV screen.

2] When a program is broadcast in second audio,

SAP appears on the TV screen.

3] When a program broadcast both in stereo and sec-

ond audio, STEREO and SAP appear on the TV

screen.

NOTE: Although a program may be broadcast in

both stereo and second audio, you cannot

record in both stereo and second audio at

the same time.

PLAY

HIFI

12:00AM

CH 123

STEREO/SAP

4] While the TV/DVD/VCR is set in HIFI stereo

mode and playback mode. HIFI appears on the

TV screen. While the TV/DVD/VCR is set in

monaural(MONO) mode, HIFI disappears from

the TV screen.

COUNT

0:00:00

Second Audio Program, which means your

program, can also be received in a second

language or sometimes a radio station.

SAP

NOTE: If you play non-HIFI tapes while the

TV/DVD/VCR is set in HIFI, HIFI will dis-

appear from the TV screen and the

TV/DVD/VCR will play automatically in

monaural.

High Fidelity records and plays back video-

tape in high quality stereo sound.

HIFI

MTS RECORDING/MONITOR MODE

TV/VCR

Type of broadcast Display on

STEREO/SAP

Hi-Fi audio track(2-channel) Normal audio

the TV screen SELECTION

L-channel

R-channel

track

Regular

-None-

-Invalid-

Mono

(monaural audio)

Stereo broadcast

Bilingual broadcast

STEREO

SAP

-Invalid-

STEREO*

L+R

Main audio

program

Main audio

program

Main audio

program

SAP*

Sub audio

program

Sub audio

program

Sub audio

program

Stereo & Bilingual

broadcast

STEREO

SAP

STEREO*

SAP*

L+R

sub audio

program

sub audio

program

sub audio

program

*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

- 23 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECTING THE MTS SYSTEM

TV/VCR

Make sure ...

TV/DVD/VCR power must be turned on.

TO SELECT MONO MODE

•

You can change the selection to “MONO” if you

want to listen to HIFI tapes in normal audio play-

back.

TO SELECT HIFI MODE

1) Press the SETUP button on the remote control.

1 Select “USER’S SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “USER’S SET UP”. Then,

press the ENTER button.

- TV/VCR SETUP -

Press the Arrow button K or L to point to “USER’S

SET UP”.Then, press the ENTER button.

2) Press the Arrow button K or L to point to

“VCR AUDIO”.

3) Press the ENTER button until [MONO] appears.

4) Press the SETUP button on the remote control to

return to TV mode.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2 Select“VCR AUDIO”

Press the Arrow button K or L to

point to“VCR AUDIO”.

– USER’S SET UP –

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

TO SELECT STEREO, SAP, OR MONO

1 Select “USER’S SET UP”

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

3 Select [HIFI]

Press the ENTER button until

[HIFI] appears.

– USER’S SET UP –

remote control.

Press the Arrow button K or L to

point to “USER’S SET UP”.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

INDEX SEARCH

– USER’S SET UP –

2 Select “TV AUDIO”

Press the Arrow button K or L to

point to“TV AUDIO”.

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

NOTES:

Normally, “HIFI” should be selected for playback

with HIFI sound.

•

3 Select [STEREO], [SAP], or [MONO]

Press the ENTER button until [STEREO], [SAP], or

[MONO] appears.

When you play non-HIFI tapes, the TV/DVD/VCR

will play automatically in the monaural mode.

•

The TV/DVD/VCR records automatically MTS

broadcasts in HIFI stereo sound unless you select

SAP mode recording before you begin recording.

•

4 To return to TV mode

Press the SETUP button on the remote control to

return to TV mode.

NOTES:

You must select the recording mode,either TV

•

AUDIO [STEREO] or [SAP] when you record a

broadcast.

“MTS RECORDING/MONITOR

Refer to

MODE”.

If you select second audio when second audio is

not

•

available, the TV/DVD/VCR will record normal

audio.

The TV/DVD/VCR records automatically MTS

broadcasts in HIFI stereo sound unless you select

SAP mode recording before you begin recording.

- 24 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CASSETTE

This TV/DVD/VCR will operate with any cassette that has the

mark. For best results,

we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/DVD/VCR. The

TV/DVD/VCR will automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/DVD/VCR, wait until the tape has

warmed to room temperature and the moisture has

evaporated.

Window

Avoid extreme heat, high humidity and magnetic

fields.

•

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

1)In the Stop mode, press the EJECT button on the

remote control or press the STOP/EJECT button on

the TV/DVD/VCR. The cassette will eject.

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

Note: You can play back a tape recorded in LP mode

(Long Play).

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Transparent Tape

NOTE:

• In DVD mode, Whether the cassette is with tab or

without tab you insert, it doesn’t start playing until

you press the PLAY button.

In TV/VCR mode, if th cassette without tab is

inserted, playback will automatically start.

- 25 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

NORMAL PLAYBACK

SLOW MOTION

TV/VCR

During pause, press the FWD button to reduce the

playback speed. The TV/DVD/VCR mutes the sound

during slow motion. Press the PLAY button to return

to normal playback.

Make sure ...

TV/DVD/VCR power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/DVD/VCR will start playback automatically.

NOTE: If it is left in the Slow mode for more than

five minutes, the TV/DVD/VCR will automatically

go into the Stop mode.

PLAY

PICTURE SEARCH

2 To begin playback

Press the PLAY button.

TV/VCR

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback. (in the

SP / LP / SLP modes)

3 To stop playback

Press the STOP button when play-

back is completed.

STOP

NOTE:

If you press the F.FWD or REW button on the

•

front panel in the DVD mode, the VCR forward

or reverse will start. Please press the STOP /

EJECT button once to stop it, twice to eject it.

2)Press it again and the TV/DVD/VCR will now search

in super high speed. (in the LP / SLP modes only)

NOTES:

If you press the PLAY button (of the TV/VCR side)

in the DVD mode, you can start the VCR playback.

•

If you press the SELECT button in the VCR play-

•

back, it will stop and the mode will change to the

DVD mode. In addition, the same function oper-

ates with the DVD side PLAY button or the

OPEN/CLOSE button.

NOTE:

Tapes recorded in the SP or LP mode will dis-

•

play a noise bar on the TV screen and the picture

may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

TRACKING ADJUSTMENT

STILL PICTURE

TV/VCR

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

You can view a still picture on the TV screen during playback

(the Still mode). Press the PAUSE button during playback.

Only tapes recorded in the SLP mode will show the least

amount of lines.Press the PLAY button to return to playback.

However when playing pre-recorded tapes or tapes

•

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL button K or L until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

NOTES:

•

You can advance the picture one frame at a time by

pressing the PAUSE button during the Still mode.

If it is left in the Pause mode for more than five

•

minutes, the TV/DVD/VCR will automatically

switch to the Stop mode.

VERTICAL HOLD CONTROL

You can reduce the noise lines by pressing the

•

CHANNEL button K or L in slow mode, too.

Tracking adjustment in Slow mode will not be set

automatically.

TV/VCR

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL button K or L.

NOTE:

If there are video noise lines on the screen, see Tracking

Adjustment section.

- 26 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

TV/DVD/VCR power must be turned on.

Insert a prerecorded tape.

•

TV/VCR

The TV/DVD/VCR has the auto repeat function that

allows you to repeat a tape indefinitely without

touching the PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

RENTAL PLAYBACK

TV/VCR

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

CHANNEL SET UP

- TV/VCR SETUP -

1 Select “USER’S SET UP”

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

remote control.

Press the SETUP button on the

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then, press the ENTER button.

remote control.

INDEX SEARCH

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then, press the ENTER button.

INDEX SEARCH

2 Set “RENTAL” to [ON]

Press the Arrow button K or L to

point to “RENTAL”.

Press the ENTER button until [ON]

appears.

USER’S SET UP

–

RENTAL

[ON]

2 Select “ALL” or “BLANK”

Press the Arrow button K or L to

point to “REPEAT PLAY”.

USER’S SET UP

–

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[HIFI]

[STEREO]

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[ALL]

[OFF]

[HIFI]

[STEREO]

Press the ENTER button repeatedly

until your desired selection [ALL]

or [BLANK] appears.

3 Exit the Rental setting

Press the SETUP button on the remote control to

return to the TV mode.

3 Exit the Repeat Play setting

Press the SETUP button on the remote control to

return to the TV mode.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/DVD/VCR.

4 Start playback

Press the PLAY button to start the Repeat Play.

“REPEAT PLAY B” appears.

•

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/DVD/VCR.

•

TO CANCEL THE RENTAL MODE

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

Repeat steps [1] and [2], select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV

mode.

If there is a power failure of any kind, the

tv/vcr/dvd will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV

mode.

If there is a power failure of any kind, the

TV/DVD/VCR will retain its memory for this fea-

ture.

- 27 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

TV/DVD/VCR power must be turned on.

Insert a tape.

•

This function will not operate in recording mode.

This function is not operative when a cassette tape

is not inserted in the TV/DVD/VCR.

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

•

ZERO RETURN

TV/VCR

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

1 Insert a tape.

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

2 Select “TIME SEARCH” mode

- TV/VCR SETUP -

Press the SETUP button on the

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

remote control.

V-CHIP SET UP

Press the Arrow button K or L to

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

point to “TIME SEARCH”.

TIME SEARCH

INDEX SEARCH

Then, press the ENTER button.

2 Reset the counter to 0:00:00

Press the C.RESET button repeatedly.

3 Enter your desired time

Press the Arrow button K or L until

your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

TIME SEARCH

2 : 50

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

If you wish to cancel the Time

Search at this point, press the SETUP button on the

remote control.

4 To activate “ZERO RETURN” mode

- TV/VCR SETUP -

Press the SETUP button on the

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

remote control.

4 Begin Time Search

By pressing the Arrow button s or B, the

TV/DVD/VCR will rewind or fast forward to the

specified point.

V-CHIP SET UP

Press the Arrow button K or L to

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

point to “ZERO RETURN”.

Then, press the ENTER button.

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

TO CANCEL THE TIME SEARCH at this

point

TIME SEARCH

Press the STOP/EJECT button on the TV/DVD/VCR

or the STOP button on the remote control. This will

delete the selected time.

TV/VCR

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

NOTES:

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

- 28 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX SEARCH

1 Select “INDEX SEARCH”

Press the SETUP button on the

remote control.

Press the Arrow button K or L to

point to “INDEX SEARCH”. Then,

press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

TIME SEARCH

INDEX SEARCH

The index mark will be made automatically when

the REC button is pressed. It will also be marked at

the starting point of Timer recording and OTR.

•

2 Enter your desired number

Press the Arrow button K or L until

the number of programs that you

want to skip appears.

INDEX SEARCH

0 3

The index mark will not be recorded if the PAUSE

button is pressed and released during recording.

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

In some cases, the index mark at the beginning of

video tape cannot be detected.

•

(Example: “03” for 3 programs)

The Index Search mode will be

canceled if the procedures are not activated in 30

seconds.

•

3 Begin Index Search

Press the Arrow button s or B. The TV/DVD/VCR

begins rewinding or fast forwarding to the beginning

of desired program.

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

NOTE: Every time an index signal is skipped, the

number in the program indicator decreases by one.

CURRENT PLAYBACK PROGRAM

Beginning of tape

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

End of tape

4 After Index Search

When the preset program is reached, the

TV/DVD/VCR will start playback automatically.

•

INDEX MARK

A video cassette must be inserted in the

TV/DVD/VCR for this function to work.

The number of Index Searches can be set up to 20.

This function will not operate in the recording mode.

When you want to cancel the Index Search while

in progress, press the STOP button.

•

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

TV/VCR

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/DVD/VCR will eject the tape and

turn itself to off.

•

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.)The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

- 29 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Make sure ...

TV/DVD/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTES:

This TV/VCR/DVD will ONLY record and view the same channel.

This TV/VCR/DVD cannot record the contents from the built-in DVD.

•

SKIPPING UNWANTED

NORMAL RECORDING

SCENES DURING RECORDING

TV/VCR

You can ONLY watch the same TV program that is

being recorded.

Press the PAUSE button to tem-

porarily stop recording.

Press the PAUSE or RECORD but-

ton to resume recording.

NOTES:

PAUSE

1 Select the channel to be

CH 10

recorded

Press the number buttons on the

remote control or the CHANNEL

button K or L.

After five minutes, the TV/DVD/VCR will auto-

matically switch to the Recording mode to prevent

tape damage.

•

Remember: If the TV/DVD/VCR is connected to a

cable box or satellite box, the TV/DVD/VCR must

be on CH3 or CH4, then the channel to be recorded

must be selected on the cable box or satellite box.

If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then dis-

appear.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

3 Begin recording

Press the RECORD button.

REC

4 Stop recording

Press the STOP button when recording is completed.

- 30 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

Push(es) Display

1 push

Recording length

(normal recording)

OTR (One Touch Recording)

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

TV/VCR

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/DVD/VCR.

17 pushes

8:00

480 minutes

Make sure ...

TV/DVD/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in

place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

NOTES:

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

TV/VCR

This function CANNOT be done from the remote

control.

You can make copies of video tapes made by friends

or relatives for your enjoyment.

•

Recording starts immediately when the REC/OTR

button is pressed.

When the REC/OTR button is pressed 18 times, the

TV/DVD/VCR returns to the Normal Recording mode.

To stop the OTR operation, press the STOP button

on the TV/DVD/VCR or on the remote control.

To show the remaining time, press the DISPLAY

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

•

You can not copy a DVD to a videotape.

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

•

Connect your TV/DVD/VCR and a Source (Playing)

VCR using the following diagram.

•

[Fig.8]

[The TV/DVD/VCR]

AUDIO

HEADPHONE

VIDEO

STOP/EJECT

F.FWD

PLAY

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

•

If the tape runs out before the end time, the

TV/DVD/VCR will switch to the Stop mode

immediately, ejects the tape and turns itself off.

•

[Ex: Source (playing)

VCR or camcorder]

If you press the POWER button during OTR, the

TV/DVD/VCR continues recording until the select-

ed length is reached.

•

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

1 Select the channel to be recorded

Press the number buttons on the remote control or

the CHANNEL button K or L.

OUT

Remember: If the TV/DVD/VCR is connected to a

cable box or satellite box, the TV/DVD/VCR must

be on CH3 or CH4, then the channel to be recorded

is selected on the cable box or satellite box.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/DVD/VCR’s cassette

compartment.

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

3)Press the SPEED button on remote control for the

TV/DVD/VCR to select the desired recording

speed (SP/SLP).

4)Press the CHANNEL button K or L on the

TV/DVD/VCR until “AUX” appears on the screen.

5)Press the RECORD button on the TV/DVD/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during copying, use the

TV/DVD/VCR’s front panel controls whenever pos-

sible. The remote control might affect the source

(Playing) VCR’s playback operation.

3 Begin OTR

OTR(2 : 30)

Press the REC/OTR button on the

TV/DVD/VCR as many times as

needed. The recording length will be

determined by the number of times

you press the REC/OTR button. Each

additional push will increase the recording time by 30

minutes. It is set up to 8 hours.

- 31 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER

AUTOMATIC TIMER

RECORDING

1 Select “TIMER PROGRAMMING”

- TV/VCR SETUP -

Press the SETUP button on the

remote control.

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

TV/VCR

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

Arrow button K. And press the

ENTER button.

You may set the TV/DVD/VCR to start and end a

recording while you are away. You can set 8 pro-

grams to record on specific days, daily or weekly

within a 1 year period.

TIME SEARCH

INDEX SEARCH

If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow stops [3] to

[8] on page 17. Then set the timer recording.

In the example below, the timer is being set to record:

•

DATE:

July 4th, 2003

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL:

TAPE SPEED:

CH61

2 Select your desired program

position (1~8)

Press the Arrow button K or L to

select the desired program position.

Then, press the Arrow button B.

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Make sure ...

- - -/- - - - - -:- -

-:- - - -

If a cable box or satellite box is connected with the

TV/DVD/VCR you will be limited to record only one

channel. And the channel selector on the

TV/DVD/VCR must be selected to the output channel

of the boxes CH 3 or CH 4 and then the actual chan-

nel to be recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/DVD/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

3 Set the channel number

Press the Arrow button K or L until

the desired channel number

appears. (Example: CH61)

Then, press the Arrow button B.

Remember: If the TV/DVD/VCR is

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

connected to a cable box or satellite box, the

TV/DVD/VCR must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box or

satellite box.

The channel you want to record is properly set in

advance. (See page 16.)

•

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed. when programs overlap;

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

CH DATE

BEGIN END

Press the Arrow button K (up)

until the desired date appears.

(Example: “7/04” for July 4th).

Then, press the Arrow button B.

- - -/- - - - - -:- -

61 7/04 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

The illustration below demonstrates the sequence

of recordings.

•

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

For every day recording : To record a TV program

at the same time on the same channel every day.

– TIMER PROGRAMMING –

(Example: Monday through Sunday)

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

Recording Sequence

Press the Arrow button L (down)

until “EVRY DAY” appears.

Then, press the Arrow button B.

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

9:00AM

10:00AM

11:00AM

12:00PM

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

*Recording period is SHADED

– TIMER PROGRAMMING –

Press the Arrow button L (down)

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

until “EVRY” and your desired

day of the week appear together.

Then, press the Arrow button B.

- 32 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER PROGRAM EXTENSION

5 Set beginning hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the Arrow button K or L until

the desired hour appears.

- - -/- - - - - -:- -

-:- - - -

TV/VCR

61 7/04 FRI 7:12^P

- - -/- - - - - -:- -

(Example: “ 7, PM” for 7:30PM)

Then, press the Arrow button B.

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

– TIMER PROGRAMMING –

CH DATE BEGIN END

2)Repeat step [1] on page 32.

6 Set beginning minute

3)Press the RECORD button and select the desired

program using the Arrow button K or L.

4)Press the RECORD button again.

Press the Arrow button K or L until

the desired minute appears.

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

(Example: “30” for 7:30PM)

Then, press the Arrow button B.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the PAUSE but-

ton on the remote control. The recording time

returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

7 Set end hour

Press the Arrow button K or L until

the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the Arrow button B.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI 7:30^P

8:30^P

- -

- - -/- - - - - -:- -

-:- - - -

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press the Arrow button K or

- - -/- - - - - -:- -

-:- - - -

5)Press the ENTER or RETURN button to exit the

setting menu. Then press the SETUP button on the

remote control to return to original mode.

61 7/04 FRI 7:30^P

8:50^P

- -

until the desired minute appears.

(Example: “50” for 8:50PM)

Then, press the Arrow button B.

- - -/- - - - - -:- -

-:- - - -

TO CORRECT A PROGRAM

9 Set the tape speed

Press the Arrow button K or

until the desired tape speed

appears. (Example: SP)

While setting a program; press the Arrow button

s to go back one step and enter the correct num-

bers using the Arrow button K or L.

After setting a program;

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI 7:30^P

8:50^P

- - -/- - - - - -:- -

-:- - - -

•

1)Press the POWER button.

2)Repeat steps [1] - [2] on page 32.

3)Press the Arrow button B (or press the Arrow

button s to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the Arrow button K or L.

4)Press the POWER button to set automatic timer

recording.

10 Finish setting the program

Press the ENTER or RETURN button. The program

is now completed.

To set another program, repeat steps [2] to [10].

Press the SETUP button on the remote control to

•

return to original mode.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

11 Set the timer

Press the POWER button to set automatic timer

recording. The RECORDING indicator lights up.

After setting a program;

1)Press the POWER button.

•

You must turn off the TV/DVD/VCR to activate

automatic timer recording.

•

2)Repeat steps [1] ~ [2] on page 32 and select a

program you want to cancel.

3)Press the C.RESET button.

4)Press the SETUP button on the remote control to

return to TV mode.

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

While recording is in progress;

•

1)Press the POWER button.

2)Press the STOP/EJECT button on the

TV/DVD/VCR.

- 33 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the RECORDING

indicator goes off.

2)Press the SETUP button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the ENTER button. The details of programs

appear on the TV screen.

5)Press the SETUP button on the remote control to

return to TV mode.

2 Set “AUTO RETURN” to [ON]

Press the Arrow button K or L to

point to “AUTO RETURN”.

Press the ENTER button until [ON]

appears.

USER’S SET UP

–

RENTAL

[OFF]

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[ON]

[HIFI]

[STEREO]

3 Auto Return will begin

When all the timer recordings are completed, the

TV/DVD/VCR will rewind to the beginning of the

recorded program(s).

HINTS FOR AUTOMATIC

TIMER RECORDING

NOTE:

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

TV/VCR

Make sure the channel you want to record is prop-

erly set in advance.

It is not necessary to press the RECORD button for

timer recording.

Recording begins automatically at the Start time.

You may watch TV or watch a DVD while a timer

recording is occurring. To watch the same TV channel

that VCR is recording, press the POWER button and

then press the SELECT button to select TV. To view a

DVD, press the POWER button and then press the

SELECT button to select DVD. Press the POWER but-

ton to turn the display off and keep the timer recording

going.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette will

be ejected when the POWER button is pressed to off.

•

4 Watch the recorded program

Press the PLAY button.

•

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

ENTER button.

If there is a power failure of any kind, the

TV/VCR/DVD will retain its memory for this fea-

ture.

•

SLEEP TIMER

•

TV/VCR

•

The Sleep Timer function turns off the

TV/DVD/VCR without using the POWER button

after a desired period of time.

If the tape runs out before the end time, the

TV/DVD/VCR will switch to the Stop mode

immediately, and the tape will be ejected.

•

NOTE:

This function does not operate during Recording

mode.

•

AUTO RETURN

1 Select “SLEEP TIMER”

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears.

TV/VCR

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

2 Set sleep time

Press the SLEEP button until your

desired sleep time appears.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

Each additional push will increase

the time by 30 minutes up to 120

minutes.

TIMER PROGRAMMING

SETTING CLOCK

Press the SETUP button on the

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

remote control.

SLEEP 120 MINUTES

Press the Arrow button K or L to

point to “USER’S SET UP”.

Then, press the ENTER button.

After 5 seconds, exit the Sleep Timer setting.

INDEX SEARCH

TO CANCEL THE SLEEP TIMER

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears. Press the SLEEP button

until “SLEEP 0 MINUTES” appears.

- 34 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

When the Closed Caption mode is OFF:

When the Closed Caption mode is ON:

Counter mode: After 5 seconds, only the counter

remains. To clear it, press the DISPLAY button.

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, press

the DISPLAY button.

The On Screen Display disappear after 5 seconds.

This is true even if the MUTE button is pressed, or

the PAUSE button is pressed while recording.

•

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

106 107 108 109 110 111 112 113 114 115 116 117 118 119 120

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

TV Display

CATV channel

TV Display

- 35 -

1C29

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

DISC TYPES

The following discs can be played back on this

TV/DVD/VCR.

[

]

DVD

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this player. If

a function you selected does not run as desired, refer to

the manual accompanying the disc.

DVD video

DVD+R/RW*

CD-R/RW*

DVD-R/RW*

Audio CD

MP3*

* Depending on the types or the writing method of the

medium some discs can not be played.

Example

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs

made on personal computers, or on DVD recorders may

not be played back properly due to the factors such as

scratches, dirt or special properties of the disc.

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

• Discs made on personal computers may not be played

back properly due to the different environment or the

settings of the application you use. We recommend

always to use the standardized, rightly formatted discs.

This player conforms to the NTSC color system. You can-

not play discs recorded in other color systems such as

PAL or SECAM.

[

]

AUDIO CD

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

¡Some discs include region codes as shown below.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on TV/DVD/VCR with the

same region code.

The following discs cannot be played back on this

TV/DVD/VCR.

[

]

MP3

Data on an MP3 is divided into sections called "groups",

and then into subsections called "tracks", each of which is

given a group or track number.

DVD with region codes other than 1 or ALL.

DVD-ROM

Example

DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

Group 1

Group 2

Track 1

Track 2

Track 3

Track 4

Track 1

Track 2

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I (Never play back, otherwise malfunction

may result.)

SACD

Photo CD (Never play back, otherwise malfunc-

tion may result.)

Video CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD may contain menus to navigate the disc and

access special features. Press the appropriate number

buttons or use the Arrow buttons (L/K/s/B) to high-

light your selection in the DVD main menu and press

the ENTER button to confirm.

DVD-V

Getting started

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

NOTES

¡Select DVD mode by pressing the SELECT button on

the remote control. Then, operate the DVD functions.

Press the POWER button.

¡The power will turn on.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Press the OPEN/CLOSE button to open disc

loading tray.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Press the DISC MENU button.

¡The DVD main menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press the PLAY button.

¡The tray will close automatically, and playback will

then start from the first chapter or track of the disc.

If the playback does not start automatically, press

the PLAY button.

If disc menu is available on the disc, audio

language, subtitle options, chapters for the

title and other options will appear for selec-

tion.

¡When you playback the DVD which a title menu is

recorded, it may appear on the screen. In this case,

refer to “TITLE MENU”.

Press the Arrow buttons (L/K/s/B) to

select an item, and the ENTER button to

confirm selection.

Press the STOP button to stop playback.

TITLE MENU

DVD-V

NOTES

¡When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and

then TV picture and sound appears in about 4 seconds.

Similarly, when the POWER button is pressed to turn

off in the DVD mode, this mode shuts down first and

then the TV/DVD/VCR’s power is turned off.

¡A “prohibited icon” may appear at

the top-right on the TV screen dur-

ing operation, warning that a pro-

hibited operation has been encoun-

tered by the DVD or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title, or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

Press the TITLE button.

¡The title menu will appear.

If the feature is not available,

may appear on the TV screen.

symbol

Press the Arrow buttons (L/K/s/B) to

select an item, and the ENTER button to

confirm selection.

CALLING UP A MENU SCREEN

DURING PLAYBACK

For DVD-Vs

¡Press the DISC MENU button to call up the DVD menu.

¡Press the TITLE button to call up the title menu.

NOTE

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

–

_{Download from Www.Somanuals.co}3_m7_{. All Manuals Search And Download.}

01A11

SLOW FORWARD /

SLOW REVERSE

RESUME

DVD-V

During playback, press the STOP button.

¡Resume message will appear on the TV screen.

During playback, press the PAUSE button.

Press and hold down the FWD g or REV

h button for a few seconds.

Press the PLAY button, playback will resume

from the point at which playback was stopped.

Each press and hold down the FWD g or

REV h button repeatedly to select the

required speed: 1/16, 1/8, 1/2 of the normal

playback.

¡To cancel resume, press the STOP button twice.

¡If turn off the TV/DVD/VCR, resume function will

be cancelled.

PAUSE

To return to normal playback, press the

PLAY button.

DVD-V

Note for using buttons on the main unit:

During playback, press the PAUSE button.

¡Playback will pause and sound will be muted.

Press the PAUSE button, then, press and hold down the

SKIP G/ SEARCHg buttons or the SKIPH

/SEARCHh buttons on the TV/DVD/VCR for a few

seconds to begin Search in 1/16 speed of the normal

playback. Press and hold down again to change speed

to 1/8. Repeat this procedure to change to 1/2.

To continue playback, press the PLAY button.

STEP BY STEP PLAYBACK

DVD-V

ZOOM

DVD-V

During playback, press the PAUSE button.

¡Playback will pause and sound will be muted.

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

The disc goes forward by one frame each

time the PAUSE button is pressed.

Press the ZOOM button during playback.

To exit step by step playback, press the

PLAY button.

¡Playback will continue.

Press the ZOOM button repeatedly to select

the required zoom factor: ZOOM1, ZOOM2,

ZOOM3, or OFF.

FAST FORWARD/REVERSE

DVD-V

MP3

Use the Arrow buttons (K/L/s / B) to

move the zoomed picture across the

screen.

During playback, press and hold down the FWD

g or REV h button for a few seconds.

To exit zoom mode, press the ZOOM button

to OFF.

Each press and hold down the FWD g or

REV h button repeatedly to select the

required speed: x2, x8, x50, x100.

NOTES

¡Zooming function does not work while disc menu is

shown.

¡Zooming function is not available on some discs.

¡For audio CDs, the speed is fixed at ×16.

¡For MP3, the speed is fixed at ×8.

To return to normal playback, press the

PLAY button.

Note for using buttons on the main unit:

During playback, press and hold down the SKIP G/

SEARCHg buttons or the SKIPH /SEARCHh

buttons on the TV/DVD/VCR for a few seconds to begin

Search in x2 speed. Press and hold down again to change

speed to x8. Repeat this procedure to change to x50 and

x100.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

DVD-V

There are three ways to begin playback on an Audio

CD at a specific Track.

During playback, press the SEARCH MODE

button three times (CD: twice) to display the

Time Search on the TV screen.

Using the Number buttons on the remote control

Within 30 seconds, enter a desired disc

time using the Number buttons on the

remote control.

Press the Number buttons to enter the

desired Track number.

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

¡Playback will start at the specified time.

¡Press the CLEAR button to erase the incorrect input.

¡To play track 26, press +10, 2, 6.

MARKER SETUP SCREEN

DVD-V

Using the SEARCH MODE button

Press the SEARCH MODE button.

¡The track search display appears.

Use markers to memorise your favorite places on a

disc.

Within 30 seconds, select a desired track

number using the Number buttons on the

remote control.

Press the SEARCH MODE button four times

(CD: three times) during playback.

¡The display screen and Markers will appear on the

¡For single digits press 0 first.

TV screen.

¡Playback will start at the selected track.

Using the SKIP

buttons

Press the Arrow buttons (s /B) to select 1,

2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- :

- - : - -” appears in the display.

During playback, press the SKIP G button to move

the next track. Press it repeatedly to skip subsequent

tracks. Press the SKIP H button to go back to begin-

ning of the current track. Press it repeatedly to go to

the previous tracks.

When reaches the desired point, press the

ENTER button.

¡If the SKIP button is pressed while the playback is

paused, the playback will be paused again after skip-

ping to the next track.

¡The Title or Track and elapsed playing time will

appear in the TV screen.

NOTE

¡The SKIP

playback is stopped.

To return to the Marker later, press the

SEARCH MODE button four times (CD: three

times) during playback and the Arrow but-

tons (s /B) to choose the desired marker,

then press the ENTER button.

G buttons are not available when

TITLE / CHAPTER SEARCH

NOTES

DVD-V

¡Opening the disc tray or turning off the power or

select AC at step 2 and press the ENTER button will

erase all Markers.

¡To clear a marker, using the Arrow buttons (s /B

position the cursor on to the marker number to be

cleared and press the CLEAR button.

Press the SEARCH MODE button once for

the Chapter search, twice for the Title

search during playback.

¡You can mark up to 10 points.

Press the SEARCH MODE or RETURN but-

ton to exit.

Enter the desired chapter/title number using

the Number buttons on the remote control.

¡Playback will start at the selected Chapter or Track.

¡Press the CLEAR button to erase the incorrect input.

¡For single digits press 0 first.

–

_{Download from Www.Somanuals.co}3_m9_{. All Manuals Search And Download.}

01A11

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

REPEAT is available only during playback.

You may determine the order in which tracks will play.

REPEAT TITLE / CHAPTER

DVD-V

To activate the repeat function, press the

REPEAT button during playback.

¡The repeat mode changes as described below every

time you press the button.

In stop mode, press the MODE button.

¡The PROGRAM screen will appear.

Press the Arrow button ▲ or ▼ to select a

track, then press the

ENTER button.

CHAPTER

(current chapter repeat) (current title repeat)

TITLE

OFF

TOTAL

(repeat off)

¡Press the CLEAR button to

erase the most recently entered

program.

NOTES

¡Repeat Title/Chapter is not available with some

scenes.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

REPEAT TRACK

Press the PLAY button to play the pro-

grammed tracks.

NOTES

To activate the repeat function, press the

REPEAT button during playback.

¡While the program is being played back, the STOP

works as follows.

¡Press the STOP button once and then the PLAY but-

ton again, playback will restart from the point where

the STOP button was pressed. (Program continued)

¡Press the STOP button twice and then the PLAY button

again, playback will restart from the track in the usual

way. (Program cleared)

¡The repeat mode changes as described below every

time you press the button.

TRACK

ALL

OFF

(repeat off)

(current track repeat)

(entire disc repeat)

¡Up to 99 programs can be entered.

¡If you like to repeat the current track in the program,

press the REPEAT button repeatedly until

TRACK appears during playback. If you like to

repeat the entire program press the REPEAT button

NOTES

¡Repeat setting will be cleared when moving to other

track.

¡Repeat playback does not function during repeat A-B

playback.

repeatedly until

ALL appears during playback.

REPEAT A-B

RANDOM PLAYBACK

DVD-V CD

Press the REPEAT A-B button at your cho-

sen starting point.

A- appears briefly on the TV screen.

This shuffles the playing order of tracks instead of

playback in the sequence.

In stop mode, press the MODE button twice.

Press the REPEAT A-B button again at your

chosen end point.

¡RANDOM screen appears.

RANDOM

CD [AUDIO]

TOTAL 0:45:55

A-B appears briefly on the TV screen, and the

RANDOM PROGRAM

no indication

repeat sequence begins.

PLAY

To exit the sequence, press the REPEAT A-

B button.

Press the PLAY button to start random playback.

NOTE

NOTES

¡The repeat A-B section can only be set within the cur-

rent title (for DVDs), or current track (for audio CDs).

¡Repeat A-B is not available with some scenes in DVD.

¡To cancel the A point which was set, press the

CLEAR button.

¡If you like to repeat the current track in the random

selection, press the REPEAT button repeatedly until

TRACK appears during playback. If you like to

repeat the entire random selection press the

REPEAT button repeatedly until

during playback.

ALL appears

¡Repeat A-B playback does not function during title,

chapter, track or all repeat playback.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

PLAYING A MP3 DISC

MP3 PLAYBACK

TRACK SELECTION

MP3

When a CD with MP3 files is in the TV/DVD/VCR,

the MP3 menu will appear on the TV screen in stop

mode.

Press the SEARCH MODE button during

playback.

¡The FILE LIST will appear.

In stop mode, press the Arrow buttons

(K/L) to select the

desired group track.

Select a desired track using the Arrow but-

tons (K/L/s/B).

¡Press the Arrow button B when you want to go to

the next hierarchy.

¡Press the Arrow button s when you want to go back

to the previous hierarchy.

¡If a group is selected, press

the Arrow or ENTER but-

ton to go on to the track selec-

tion screen. Press the Arrow

buttons (K /L ) to choose a

track, then press the ENTER button.

Press the PLAY button to start playback.

NOTES

¡If a track is selected, press the ENTER button to start

playing tracks. Starting from the one you’ve just

chosen the subsequent tracks will be played.

¡Choose FIRST PLAY to start playback from the

beginning of the listed tracks.

¡Press the SEARCH MODE button to exit.

¡Some selections may take a while to be recognized.

PROGRAM

¡Press the TITLE button to return to the first item.

MP3

Press the STOP button to stop playback.

NOTES

This feature allows you to program an MP3 disc to

play in a desired sequence.

¡Folders are known as Groups; files are known as

Tracks.

In stop mode, press the MODE button.

¡The PROGRAM screen will appear.

¡MP3 files are accompanied by

icon.

¡Maximum of 255 folders can be recognized.

¡Maximum of 256 files can be recognized.

¡Up to 8 hierarchies can be created.

This player recommends the use of files recorded at

the below specifications:

¡Sampling frequency: 44.1kHz or 48kHz

¡Constant bit rate: 112kbps ~ 320kbps.

Select a desired track using the Arrow but-

tons (K/L/s/B). Then, press the ENTER

button.

¡Press the Arrow button B when you want to go to

the next hierarchy.

¡Press the Arrow button s when you want to go back

to the previous hierarchy.

¡Press the CLEAR button to erase the most recently

entered program.

Repeat step 2 until you have selected all the

Tracks you want to play in the program.

Press the PLAY button to start programmed

playback.

RANDOM PLAYBACK

MP3

In stop mode, press the MODE button twice.

¡RANDOM screen appears.

Press the PLAY button to start random play-

back.

–

_{Download from Www.Somanuals.co}4_m1_{. All Manuals Search And Download.}

01A11

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

CAMERA ANGLE

DVD-V

The DVD allows you to select a language for subtitles Some DVD discs contain scenes which have been shot

during DVD disc (if available) playback. simultaneously from various angles. You can change

the camera angle when the (

screen.

) icon appears on the

Press the SUBTITLE button during playback.

Press the SUBTITLE button repeatedly to

select your desired subtitle language.

Press the ANGLE button during playback.

¡The selected angle will be displayed on the display

¡The subtitle language will be displayed on the dis-

play bar at the top of the screen.

bar at the top of the screen.

Press the ANGLE button repeatedly to

select your desired angle.

To turn off subtitles, press the SUBTITLE

button repeatedly until OFF appears.

NOTES

BLACK LEVEL SETTING

Some discs allow audio language setting/subtitle language

setting on the disc menu. (Operation varies between discs,

so refer to the manual accompanying the disc.)

DVD-V

¡If the desired language is not shown after pressing

the SUBTITLE button several times, the disc does

not have subtitles in that language.

Adjust the Black Level Settings to make the black

parts of the picture brighter.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, ‘---’ will be displayed instead.

(Refer to page 44.)

Press the MODE button during playback.

AUDIO LANGUAGE

Press the ENTER button to switch OFF.

ON: Makes the dark parts brighter.

DVD-V

OFF: Shows the original picture as recorded.

The TV/DVD/VCR allows you to select a language

during DVD disc (if multi language available) play-

back.

Press the MODE button twice or the

RETURN button to exit.

VIRTUAL SURROUND

Press the AUDIO button during playback.

Press the AUDIO button repeatedly to select

your desired language.

DVD-V

MP3

You can enjoy stereophonic visual space on your exist-

ing stereo system.

¡Make sure you are using the AUDIO L/R analog out

jack on the rear panel of the TV/DVD before you use

this feature.

NOTE

¡Pressing the AUDIO button may not work on some

DVDs with multiple audio languages (e.g. DVDs

which allow audio language setting on the disc menu).

STEREO SOUND MODE

Press the MODE button twice (CD/MP3:

once) during playback.

OFF

Press the AUDIO button repeatedly during

playback to select between STEREO, L-CH

or R-CH.

Press the ENTER button to set it 1 (Natural

effect) or 2 (Emphasized effect) or OFF.

STEREO - both right and left channels are active (stereo)

L-CH - only left channel is active

R-CH - only right channel is active

Press the MODE or RETURN button to exit.

NOTE (for CD play only)

NOTE

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

¡If the Virtual Surround setting is ON, the sound mode

will be fixed to STEREO, and can not be changed.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

THE ON-SCREEN INFORMATION

DVD-V

MP3

You can check the information about the current disc by pressing the DISPLAY button on the remote control.

For DVD-Vs

For audio CDs

Press the DISPLAY button during playback

to show current Chapter.

Press the DISPLAY button during playback

to show the current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

9/49

0:00:00 -0:00:00

Press the DISPLAY button again to show

current Total Track.

Press the DISPLAY button again to show

current Title.

¡The elapsed and remaining playing time of the cur-

rent total track will be displayed.

rent title will be displayed.

Press the DISPLAY button again to exit the

display.

Press the DISPLAY button again.

¡The BIT RATE and the current repeat setting will be

displayed.

For MP3

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

Press the DISPLAY button during playback.

¡The name of the file currently in play will be dis-

played.

Press the DISPLAY button again to exit the

display.

Press the DISPLAY button repeatedly to

show the track number, the repeat status,

and the playback status at the top of the

screen.

will be displayed when repeat play has been

selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates Disc repeat

Press the DISPLAY button again to exit the

display.

–

_{Download from Www.Somanuals.co}4_m3_{. All Manuals Search And Download.}

01A11

CHANGING THE DVD SETUP ITEMS

LANGUAGE SETTING

Language

Code Language

Code

DVD-V

A-B

L-N

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

4748 Laothian

4747 Latin

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Language options are not available with some discs.

Press the SETUP button twice in STOP

mode so that the DVD SETUP menu

appears.

4771 Malayalam

4772 Maltese

4847 Maori

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

5167 Marathi

4860 Moldavian

5072 Mongolian

4854 Nauru

QUICK SETUP

4855 Nepali

4864 Norwegian [NOR]

4853

5971 Occitan

4851 Oriya

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

5161

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

TV MODE

DOLBY DIGITAL ON

4:3 LETTER BOX

Bulgarian

Burmese

Byelorussian

O-R

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

C-E

Press the Arrow button B to select CUS-

Cambodian

Catalan

TOM, then press the ENTER button.

Chinese [CHI]

Corsican

Croatian

¡CUSTOM mode will appear.

Czech

Press the Arrow buttons (s /B) to select

LANGUAGE, then press the ENTER button

to confirm.

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

F-H

Faroese

Fiji

LANGUAGE

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

Finnish [FIN]

French [FRE]

Frisian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

Galician

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Press the Arrow buttons (K/L) to select the

next items, then press the ENTER button.

5051 Sindhi

5158 Singhalese

5758 Siswat

5360 Slovak

AUDIO:

¡Sets the audio language.

SUBTITLE:

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

¡Sets the subtitle language.

DISC MENU:

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Swedish [SWE]

¡Sets the language for DVD menu.

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Press the Arrow buttons (K/L) to select a

setting, then press the ENTER button.

¡If OTHER is selected on the AUDIO, SUBTITLE or

DISC MENU screen, press four-digit number to

enter the code for the desired language. (Refer to the

language code list below.)

¡Only the languages supported by the disc can be

selected.

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

Kazakh

Kinyarwanda

Kirghiz

Kirundi

6460

U-Z

Press the SETUP button to exit.

Korean [KOR]

Kurdish

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

NOTE

¡Language Setting for Audio and Subtitle is not avail-

able with some discs. Then use the AUDIO and the

SUBTITLE buttons. Details are on page 42.

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

TO CHANGE THE ON-SCREEN MENUS

You can access the TV/VCR SETUP menu by pressing

the SETUP button from the DVD mode. Refer to

“Selecting the Language” on page 16 to changing the

on-screen menus.

¡In case of selecting from the DVD mode, you cannot

select “CHANNEL SET UP”, “V-CHIP SET UP”,

“CAPTION”, “TIME SEARCH”, or “INDEX

SEARCH” menus.

Yoruba

Zulu

If you choose a Language that has a 3 letter language

code, the code will be displayed every time you change

the Audio or Subtitle language setting on page 42. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

DISPLAY SETTING

AUDIO SETTINGS

Choose the appropriate Audio settings for your equip-

ment as it only affect during the playback of DVD

discs.

DVD-V

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

Press the SETUP button twice in STOP mode

so that the DVD SETUP menu appears.

Press the SETUP button twice in STOP mode

so that the DVD SETUP menu appears.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

QUICK SETUP

TV MODE

4:3 LETTER BOX

DOLBY DIGITAL ON

QUICK SETUP

TV MODE

4:3 LETTER BOX

DOLBY DIGITAL ON

Press the Arrow button B to select CUS-

TOM, then press the ENTER button.

Press the Arrow button B to select CUS-

TOM, then press the ENTER button.

¡CUSTOM mode will appear.

Press the Arrow buttons (s /B) to select

AUDIO, then press the ENTER button to

confirm.

Press the Arrow button (s/B) to select DIS-

PLAY, then press the ENTER button to confirm.

AUDIO

DRC

OFF

DOLBY DIGITAL

DOWN SAMPLING ON

DISPLAY

TV MODE

4:3 LETTER BOX

ANGLE ICON

AUTO POWER OFF ON

Press the Arrow buttons (K/L) to select the

below items, then press the ENTER buttons.

Press the Arrow buttons (K/L) to select the

below items, then press the ENTER button.

DRC (Dynamic Range Control):

¡To compress the range of soft to loud sound.

¡The default setting is OFF.

TV MODE:

QUICK

¡Press the Arrow buttons (K/L) for an item selection,

then press the ENTER button.

¡Select 4:3 LETTER BOX for a black bars appears

on top and bottom of the screen.

DOLBY DIGITAL:

Set to On when the unit is connected to a Dolby Digital

Decoder.

QUICK

(ON: Output a Dolby Digital signal)

(OFF: Convert the Dolby Digital to PCM (2 channel

stereo))

¡Select 4:3 PAN & SCAN for a full height picture

with both sides trimmed.

¡The default setting is 4:3 LETTER BOX.

¡The default setting is ON.

ANGLE ICON:

¡Press the ENTER button repeatedly to turn Angle

icon ON or OFF.

DOWN SAMPLING:

¡Set to ON when outputting in 48 kHz.

¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

AUTO POWER OFF:

¡Press the ENTER button repeatedly to turn Auto

Power off ON or OFF.

¡The default setting is ON and it will turn the

TV/DVD/VCR to off automatically after 15 minutes

of no use.

Press the SETUP button to exit.

–

_{Download from Www.Somanuals.co}4_m5_{. All Manuals Search And Download.}

01A11

PARENTAL CONTROL

CONTROL LEVELS

DVD-V

ALL

All parental lock is cancelled.

Parental Control limits the disc viewing that exceed

your settings. (with a password or playback will stop.)

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Levels 7 to 2

PARENTAL LEVEL

Only DVD software intended for general use and

children can be played back.

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

Level 1

Press the SETUP button twice in STOP mode

so that the QUICK SETUP menu appears.

¡If the menu does not appear, press the PLAY button,

the STOP button, then the SETUP button twice.

IF YOU FORGET THE PASSWORD

QUICK SETUP

Press the number buttons 4, 7, 3, 7 at step 4.

Then enter your new password.

TV MODE

DOLBY DIGITAL ON

4:3 LETTER BOX

¡Password will be cleared and parental level will be

set to ALL.

Press the Arrow button B to select CUS-

TOM, then press the ENTER button.

Proceed the above Steps 5-7 again.

Press the Arrow buttons (s/B) to select

PARENTAL, then press the ENTER button.

PARENTAL

PARENTAL LEVEL ALL

Enter your four-digit password then press

the ENTER button.

Press the Arrow buttons (K/L) to select

PARENTAL LEVEL, then press the ENTER

button.

Press the Arrow buttons (K/L) to select

the desired level.

Press the SETUP button to exit

NOTES

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the

password.(in the event you forget the password, see

below)

¡To change the password, press the Arrow buttons

(K/L) to select CHANGE at step 5, then press the

ENTER button. Enter the four-digit pass-word, then

press the ENTER button.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

¡Record the password in case you forget it.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

TROUBLESHOOTING GUIDE

If the TV/DVD/VCR does not perform properly when operated as instructed in this Owner’s Manual, check

the player, consulting the following checklist.

PROBLEM

CORRECTIVE ACTION

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote.

You have to be within 23 feet of the TV/DVD/VCR.

No power.

•

The TV/DVD/VCR does not

respond to the remote control.

•

Check if the correct mode is selected. If not switch the mode by

pressing the SELECT button on the remote control,whichever you need.

TV/VCR Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture and sound.

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Press the SELECT button on the remote control to select TV mode.

Then try other TV feature.

•

Let the TV/DVD/VCR program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust COLOR control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust CONTRAST & BRIGHT control.

•

No picture or poor picture on

TV/DVD/VCR.

No sound or poor sound.

Bars On Screen

Picture Distorted or Blurred

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Try a new channel, if OK, then possible station trouble.

Is antenna connected to terminal on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Adjust CONTRAST & BRIGHT control.

–

_{Download from Www.Somanuals.co}4_m7_{. All Manuals Search And Download.}

01A11

PROBLEM

Picture OK, Sound Poor

CORRECTIVE ACTION

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/DVD/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

•

Timer recording is not possible.

Cannot go into Record mode.

Playback picture is partially noisy. • ^{Adjust tracking control for a better picture using the CHANNEL}

• ^{button K or L on the TV/DVD/VCR.}

No picture but the audio is OK in

playback.

• Head cleaning may be necessary. Refer to “AUTO HEAD

• CLEANING” on page 50.

No operation by infrared Remote

Control.

Video or color fades in and out

• ^{Make sure the AC cord is connected to an AC outlet.}

• ^{Check batteries in remote control.}

• ^{You can not copy a copyrighted video tape. You are experiencing}

when making a copy of a video tape^.• ^{copy guard protection.}

Different color marks on screen.

Magnetism from nearby appliances and geomagnetism might affect

•

the color of the TV picture. Move the

away from the

TV/DVD/VCR

appliances, the

can repair itself automatically. If you

TV/DVD/VCR

want to repair immediately, turn off using the POWER button, then

turn it on again 30 minutes or so later.

CLOSED CAPTION PROBLEM

My TV/DVD/VCR is showing

captions that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/DVD/VCR will not show

the text dialogue

• Captions that are delayed a few seconds behind the actual

are common for live broadcast. Most captioning production

in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words

what is being said.

• per minute. If a dialogue exceeds that rate, selective editing is used

• to insure that the captions remain up-to-date with the current

• TV screen dialogue.

My captions are scrambled with

white boxes on the TV screen.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

DVD Mode

PROBLEM

No picture.

CORRECTIVE ACTION

• Connect the video cables firmly.

• Insert a correct video disc that plays on this TV/DVD/VCR.

• Press the SELECT button on the remote control to select DVD mode.

Then, try other DVD feature.

• Insert the disc.

Disc cannot be played

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

No sound

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

• This TV/DVD/VCR does not support DTS audio. This is not a mal-

function.

No DTS audio is output

• There are some cases where pictures may be slightly distorted, which

are not a sign of a malfunction.

Distorted picture

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language

does not match the set up

•

The selected language is not available for audio or subtitles on the DVD.

This is not a malfunction

The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera

angles. This is not a malfunction

Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected

changed

language. This is not a malfunction.

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

• That operation is prohibited by the player or the disc.

This is not a malfunction.

• Scratched disc. Replace the disc with unscratched one.

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

–

_{Download from Www.Somanuals.co}4_m9_{. All Manuals Search And Download.}

01A11

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-488-1222, to

locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the TV/DVD/VCR with a soft cloth immersed in

lukewarm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/DVD/VCR. Such chemi-

cals may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/DVD/VCR become inoperative,

•

do not try to correct the problem by yourself. There

are no user-serviceable parts inside. Turn off,

unplug the power cord, and please call our help

line at 1-800-488-1222, to locate an Authorized

Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/DVD/VCR may

need to be cleaned.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the player still does not perform properly when it is operated while referring to the relevant sections and to

"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult

your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

•

DISC HANDLING

Use discs which have the following logos on them.

(Optical audio digital discs.)

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

ReWritable

Recordable

Do not use detergent or abrasive cleaning agents.

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

Always store the disc in its protective case when it

is not used.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

01A11

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

TV/VCR

CRT

OTHER SPECIFICATIONS

[23 inch model]:

[27 inch model]:

Television system :

23 inch in-line gun, 90˚

Terminals

Antenna input:

deflection tube

27 inch in-line gun, 110˚

deflection tube

NTSC-M

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video input:

Audio L/R input:

Headphone:

Closed caption system :§15.119/FCC

1/8” stereo (3.5 mm)

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary four-head

1/2 inch

Coaxial digital

audio output:

One pin jack,

500m Vpp (75 ohm)

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Analog audio L/R

output :

Remote control:

RCA connector [ 2

Digital encoded

infrared light system

#2~#6

#7~#13

#14~#69

Operating

temperature:

5ºC to 40ºC

(41ºF~104ºF)

Power requirements: AC 120V, 60Hz

[23 inch model]

VHF :

MID band :

SUPER band :

HYPER band :

A5~A1, A~I

J~W

W+1~W+84

Power consumption

(Maximum):

Picture tube:

Dimensions:

120W

23"

H:23-3/4” (594mm)

W:24-1/2” (612mm)

D:18-15/16” (473mm)

61.6 lbs (28.0kg)

DVD

Product type:

Discs:

Output signal format: NTSC color

Frequency response

(out put jack)

DVD (linear sound): 20 Hz to 22 kHz

(sample rate: 48 kHz)

DVD Player

DVD video, Audio CD

Weight:

[27 inch model]

Power consumption

(Maximum):

Picture tube:

Dimensions:

125W

27"

H:25-1/2” (648mm)

W:26-9/16” (675mm)

D:19-11/16” (500mm)

86 lbs (39.0kg)

20 Hz to 44 kHz

(sample rate: 96 kHz)

20 Hz to 20 kHz

Weight:

CD:

Signal-to-noise ratio

(S/N ratio)(out put jack)

CD:

75 dB (EIAJ)

Dynamic range

(out put jack)

DVD (linear sound): 85 dB

CD:

84 dB (EIAJ)

Total distortion factor

CD:

Wow and flutter:

0.07% (EIAJ)

Below the measurement

limitation (+/-0.001%

W PEAK) (EIAJ)

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

–

_{Download from Www.Somanuals.co}5_m1_{. All Manuals Search And Download.}

01A11

11. Botones CHANNEL K/L

INDICE

Utilice estos botones para seleccionar canales memorizados.

12. Indicador de grabación

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52

MANDO A DISTANCIA. . . . . . . . . . . . . . . . . . . . . . . . . 52

VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54

MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54

CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

Parpadea durante la grabación. Se ilumina durante el

modo de espera de grabación controlada por temporizador.

13. Botón REC/OTR (RECORD)

Presione este botón para grabar manualmente. Este

botón también activa la función de grabación instan-

tánea (OTR). (La función OTR sólo está disponible

durante el modo TV/VCR.)

14. Botón REW (para VCR)

Presione este botón para rebobinar la cinta o para ver

la imagen rápidamente en dirección de retroceso

durante el modo de reproducción. (Búsqueda en direc-

ción de retroceso)

EQUIPADO CON TOMAS DE ENTRADA DIGITAL,

PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54

CONEXIÓN A UN RECEPTOR CON DECODIFICADOR

15. Botón FWD (para VCR)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

DOLBY DIGITAL

Presione este botón para adelantar rápidamente la cinta

o para ver la imagen rápidamente en dirección de

avance durante el modo de reproducción. (Búsqueda en

dirección de avance)

SECCIÓN DE TV/VCR

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54

PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 55

CÓMO BORRAR (AGREGAR) CANALES . . . . . . . . . . 55

16. Botón STOP/EJECT (para VCR)

Presione este botón para detener la cinta. Presiónelo en

el modo de parada para retirar la cinta del

televisor/DVD/videograbadora.

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

17. Ventanilla del sensor de mando a distancia

CONTROLES DE

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar

en privado.

OPERACIÓN Y FUNCIONES

19. Toma de entrada VIDEO

Conecte a la toma de salida de vídeo de una videocá-

mara, videograbadora o juego de vídeo.

PANEL FRONTAL DEL

TELEVISOR/DVD

20. Tomas de entrada AUDIO L/R

Conecte a las tomas de salida de audio de una videocá-

mara, videograbadora juego de vídeo.

Consulte la figura 1 de la página 9

21. Compartimiento para cassette de vídeo

MANDO A DISTANCIA

22. Botón PICTURE

Consulte la figura 2 de la página 9

Presione este botón para ajustar la imagen.

23. Botones numéricos

VISTA POSTERIOR

Modo TV:

Presione dos botones para acceder directamente al

canal deseado.

Consulte la figura 3 de la página 10

No olvide presionar “0” antes de elegir un canal de un

solo dígito.

1. Botón POWER

Presione este botón para conectar y desconectar la ali-

mentación.

2. Botones VOLUME X/Y

Presione estos botones para controlar el nivel de volumen

del DVD y el televisor.

Botón +100

Presione este botón para seleccionar canales de tele-

visión por cable cuyo número sea igual o superior a 100.

Modo DVD:

Presione este botón para introducir el número deseado.

Botón +10

3. Botones SKIP (para DVD)

Presione este botón para introducir números iguales o

Presione el botón correspondiente una vez para omitir

capítulos o pistas y desplazarse a un punto específico.

Mantenga el botón presionado para cambiar la veloci-

dad de reproducción en avance o retroceso.

mayores que 10

24. Botón PAUSE

Hace una pausa en la reproducción del disco o cinta.

4. Botón PLAY

25. Botón SPEED

Inicia la reproducción del contenido del disco o cinta.

Presione este botón para seleccionar la velocidad de

grabación deseada: SP/SLP.

5. Botón STOP

Detiene la operación del disco. (unidad principal)

Detiene la operación de los contenidos del disco o

cinta. (control remoto)

26. Botón C.RESET

Presione este botón para poner el contador en 0:00:00.

Presiónelo también para cancelar un ajuste de progra-

ma de temporizador.

6. Botón OPEN/CLOSE

Presione para abrir la bandeja de disco e insertar un

disco o para sacar un disco.

7. Bandeja de carga del disco

8. Indicador DVD

Se ilumina durante el modo DVD.

9. Botón SELECT

Presione este botón para cambiar al modo TV/VCR,

modo de entrada externa o modo de DVD.

27. Botón DISPLAY

Modo TV/VCR:

Para visualizar el contador o el número del canal y la

fecha actual en la pantalla del televisor.

Modo DVD:

Indica el estado actual en la pantalla del televisor para

fines de comprobación.

28. Botón SETUP

Presione este botón para activar o salir del modo de

menús de televisor o configuración de DVD.

10. Indicador TV/VCR

Se ilumina durante el modo TV/VCR.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

29. Botón TITLE

ANTENAS SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena

exterior.

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

Utilice esta conexión si su sistema de televisión por

cable se conecta directamente a su televisor/DVD/

videograbadora, sin una caja de convertidor.

Con esta conexión podrá:

1) Utilizar el mando a distancia del televisor/DVD/

videograbadora para seleccionar canales.

2) Programar uno o más canales decodificados para

grabación automática controlada por temporizador.

NOTA: Este televisor/DVD/videograbadora SÓLO

puede grabar el canal que se está viendo.

Para visualizar el menú de títulos.

30. Botón CLEAR

Para cancelar ajustes.

31. Botón MODE

Activa el modo de reproducción programada o el modo de

reproducción aleatoria.

32. Botón SEARCH MODE

Presione este botón para localizar un punto deseado.

33. Botón AUDIO

Presione este botón para seleccionar un idioma de

audio o el modo de sonido deseado.

34. Botón SUBTITLE

Presione este botón para seleccionar el idioma de subtí-

tulos deseado.

35. Botón REPEAT

Repite la reproducción del disco, título, capítulo o pista actual.

36. Botón ANGLE (modo DVD)

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

Presione este botón para cambiar el ángulo de la cámara

y ver la secuencia que se está reproduciendo desde un

ángulo diferente.

Si su compañía de televisión por cable le suministra

una caja de convertidor o si utiliza un sistema de

satélite, podrá utilizar la conexión básica que se

muestra en la ilustración.

37. Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

38. Botón RETURN

Permite volver a la operación anterior en el modo de

configuración de DVD.

Al utilizar esta conexión, también podrá grabar canales

codificados. Sin embargo, la selección de los canales

deberá hacerse con la caja de convertidor o con la caja

de satélite. Esto significa que no es posible cambiar de

canal utilizando el mando a distancia del televisor/DVD/

videograbadora. La grabación en ausencia (controlada

por temporizador) está limitada a un canal a la vez.

PARA GRABAR UN CANAL

39. Botón ENTER

Presione este botón para establecer un ajuste.

40. Botones de flechas

Modo TV/VCR:

Presione estos botones para seleccionar un modo de

ajuste en el menú que aparece en la pantalla del televisor.

Presiónelos también para seleccionar opciones o

establecer ajustes en un menú en particular.

Modo DVD:

CODIFICADO/DECODIFICADO

1.Ajuste el selector de canales del

Use estos botones para hacer ajustes mientras observa

la imagen en la pantalla del televisor.

televisor/DVD/videograbadora al canal de salida de

la caja de convertidor de televisión por cable o caja

de satélite. (Ej., CH3)

41. Botón DISC MENU

Muestra los menús contenidos en el DVD.

42. Botón ZOOM

2.Seleccione el canal que desea grabar en la caja de

convertidor de televisión por cable o caja de satélite.

Amplía parte de la imagen reproducida de un DVD.

43. Botón MUTE

Suprime la salida de sonido. Presiónelo de nuevo para

restablecer el sonido.

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que pro-

porciona recomendaciones para hacer una conex-

ión a tierra apropiada y, en particular, especifica

que la tierra del cable debe conectarse al sistema

de puesta a tierra del edificio, tan cerca del punto

de entrada del cable como sea posible.

44. Botón SLEEP

Utilice este botón para ajustar el temporizador de dormir.

45. Botón SELECT

Presione este botón para cambiar entre los modos

TV/VCR y DVD. El modo seleccionado (TV/VCR o

DVD) se visualiza en el indicador del panel delantero.

46. Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por cable

o sistema de satélite.

47. Cable de alimentación

Conéctelo a una toma de CA estándar (120 V, /60 Hz).

NOTA: Antes de conectar el cable de alimentación a

una toma de CA estándar, retírelo del gancho

para evitar dañarlo.

CONEXIÓN A TOMAS DE

ENTRADA EXTERNA

Cuando vea un programa grabado en otra fuente (videograbado-

ra o videocámara), utilice las tomas de entrada de audio/vídeo

de la parte delantera del televisor/DVD/videograbadora.

Conecte las tomas de salida de audio/vídeo de otra fuente a

las tomas AUDIO L/R y VIDEO de este

48. Toma de salida de audio digital COAXIAL

Conéctela solamente a la entrada digital de un amplifi-

cador externo o decodificador de audio de DVD.

49. Terminal de salida analógico AUDIO L/R

Conecte a la entrada de audio analógica de un amplifi-

cador externo o sistema estéreo.

televisor/DVD/videograbadora. Luego, presione los botones

CHANNEL K/L hasta que aparezca "AUX" en la pantalla.

NOTA:

Cuando conecte una videograbadora monofónica (otra

fuente) a este televisor/DVD/videograbadora, conecte la

toma de salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de este

televisor/DVD/videograbadora. El audio saldrá igual-

mente por los canales izquierdo y derecho.

•

PREPARACIÓN PARA LA

UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE

Consulte la figura 4 de la página 11

Consulte la figura 5 de la página 12

–

_{Download from Www.Somanuals.co}5_m3_{. All Manuals Search And Download.}

0C28

CONEXIÓN A UN RECEPTOR CON

DECODIFICADOR DOLBY DIGITAL

PARA INSERTAR LAS PILAS

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a distancia en el

sentido de la flecha.

Si se utiliza este TV/DVD/VCR para reproducir un

disco DVD, el TV/DVD/VCR emite flujo de datos

DOLBY DIGITAL de su terminal de salida de audio

digital COAXIAL. Al conectar el reproductor a un

receptor con codificador DOLBY DIGITAL, puede

disfrutar de un ambiente más convincente y real con un

sonido envolvente de alta potencia y calidad como el

que se escucha en las salas de cine.

2) Inserte 2 pilas "AA" en el compartimiento de las

pilas, en el sentido indicado por las marcas de

polaridad (+/-).

3) Vuelva a poner la cubierta.

MODO DE ENTRADA EXTERNA

Consulte la figura 8 de la página 14

NOTAS:

Al usar una señal de entrada externa (otra videograbado-

ra o una videocámara), conecte los cables de salida de

audio/vídeo del equipo externo a las tomas AUDIO L/R

IN/ VIDEO IN de su televisor/DVD/videograbadora.

Luego, presione los botones CHANNEL K/L hasta que

aparezca "AUX" en la pantalla.

Asegúrese de desconectar la alimentación de todos

•

los componentes del sistema antes de conectar otro

componente.

Consulte los manuales de instrucciones de los

•

componentes que va a conectar al

televisor/DVD/videograbadora.

CONEXIÓN A UN SISTEMA

Si se conecta a un receptor con decodificador

ESTÉREO

•

Dolby Digital, ajuste DOLBY DIGITAL a ON

para salida de audio en el modo de configuración.

NOTAS:

•

Asegúrese de desconectar la alimentación de todos

A menos que esté conectado a un receptor con

•

los componentes del sistema antes de conectar otro

componente.

decodificador Dolby Digital, ajuste DOLBY DIGI-

TAL a OFF para salida de audio en el modo de

configuración. Cuando se reproduce un

Consulte el manual de instrucciones de su sistema

•

estéreo y de cualquier otro componente que vaya a

conectar al televisor/DVD/videograbadora.

TV/DVD/VCR utilizando unos ajustes incorrectos

puede hacer que se genere ruido y también puede

causar daño a los altavoces.

Para sonido de TV-VCR-DVD analógico estéreo

•

(2 canales).

Solo el audio DVD está disponible utilizando la

•

toma de salida de audio COAXIAL.

Consulte la figura 6 de la página 13

Para el sonido de audio de TV y VCR, por favor

•

remítase a la sección “CONEXIÓN A UN SIS-

TEMA ESTÉRO”. Es necesario utilizar esta

conexión en adición a la anterior para poder disfru-

tar de un sonido de TV y VCR a través del mismo

receptor.

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CON TOMAS

DE ENTRADA DIGITAL, PLATINA

MD O PLATINA DAT

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D

doble son marcas de fábrica de Dolby

Laboratories.

Utilice un cable digital coaxial de audio de venta en el

comercio especializado para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

Consulte la figura 7 de la página 13

SECCIÓN DE TV/VCR

NOTAS:

La fuente de audio de un disco grabado en formato

•

PREPARACIÓN PARA LA

UTILIZACIÓN

de sonido envolvente Dolby Digital de 5,1 canales

no se puede grabar como sonido digital mediante

una platina MD o DAT.

Puede programar el sintonizador para explorar todos

Asegúrese de desconectar la alimentación de todos

•

los canales que pueda recibir en su zona.

los componentes del sistema antes de conectar otro

componente.

NOTA: La programación de la memoria de canales

NO es necesaria cuando se hace la conexión a una

caja de televisión por cable o a una caja de satélite.

Simplemente ajuste el selector de canales del televi-

sor/DVD/videograbadora a la posición correspondi-

ente al canal de salida de la caja de televisión por

cable o caja de satélite (ej., CH3). Luego, seleccione

el canal que desea ver en la caja de televisión por

cable o en la caja de satélite.

Consulte los manuales de instrucciones de los

•

componentes que va a conectar al

televisor/DVD/videograbadora.

Ajuste la función Dolby Digital a OFF para salida

•

de audio en el modo de configuración. La repro-

ducción en un televisor/DVD/videograbadora uti-

lizando ajustes incorrectos puede generar ruido y

distorsión, y también puede causar daños a los

altavoces.

Solo para sonido de DVD digital estéreo (2 canales).

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

0C28

2 Seleccione “AGREGAR/BORRAR”

Presione el botón de flecha K o L para señalar

“AGREGAR/BORRAR”.

PREAJUSTE DE CANALES

TV/VCR

Presione el botón ENTER.

1 Conecte el cable de alimentación del televi-

3 Introduzca el número del canal deseado

Presione el botón de flecha K o L hasta que aparez-

ca el número del canal deseado. (También puede uti-

lizar también los botones numéricos o los botones

CHANNEL K/L para introducirlo.) (Ejemplo: CH8)

sor/DVD/videograbadora

Conecte el cable de alimentación del

televisor/DVD/videograbadora

NOTA:

Si aparecen algunos dígitos en la esquina de la pan-

talla, presione el botón POWER sin desconectar el

cable de alimentación.

•

4 Borre el canal de la memoria o agréguelo a

ella

Presione el botón ENTER. El número del canal

seleccionado se ilumina de color rojo. El canal de

borra de la memoria.

2 Encienda el televisor/DVD/videograbadora

Presione el botón POWER para encender el televi-

sor/DVD/videograbadora.

Canal agregado: Se enciende en azul.

Canal borrado: Se enciende en rojo.

3 Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

Presione el botón ENTER para seleccionar "ENG-

LISH" = inglés, "ESPAÑOL" o "FRANÇAIS" =

francés. "[ ]" indica el idioma seleccionado.

4 Inicie el preajuste automático

Presione el botón de flecha K o L para señalar

"AUTOPRESELECCION".

Luego, presione el botón ENTER.

El sintonizador explora y memoriza todos los canales

activos de su zona.

Para borrar otro canal, repita los pasos [3] y [4].

•

Si vuelve a presionar el botón ENTER, el canal se

•

memorizará de nuevo.

Presione el botón RETURN para hacer que el tele-

•

visor/videograbadora vuelva al menú SETUP.

5 Salga del modo de preajuste de canales

Presione el botón SETUP del mando a distancia para

volver al modo de televisor.

NOTA: Para confirmar que los canales han sido borra-

dos o agregados, presione el botón CHANNEL K o L.

NOTAS:

El televisor/DVD/videograbadora distingue entre

•

los canales de TV estándar y los canales de tele-

visión por cable.

SECCIÓN DE DVD

Si desea reproducir o grabar una cinta de vídeo

•

ANTES de preajustar el sintonizador, deberá pre-

sionar el botón SETUP del mando a distancia.

El televisor/DVD/videograbadora puede memorizar

canales de TV como canales de CATV si las condi-

ciones de recepción no son buenas. Si esto sucede,

vuelva a intentar la acción AUTO MEMO cuando

las condiciones de recepción mejoren.

REPRODUCCIÓN BÁSICA

•

DVD-V

Para empezar

¡Conecte la alimentación del amplificador y otros

componentes, si es necesario.

5 Una vez finalizada la exploración

El sintonizador se detiene en el canal memorizado

más bajo. Si desea recuperar los canales selecciona-

dos, podrá seleccionar los canales directamente con

los botones numéricos o los botones CHANNEL K o

L del mando a distancia.

Presione el botón POWER.

¡La alimentación se conectará.

Presione el botón OPEN/CLOSE para abrir

la bandeja de carga del disco.

CÓMO BORRAR (AGREGAR)

CANALES

Ponga el disco deseado en la bandeja, con

la etiqueta hacia arriba.

TV/VCR

Presione el botón PLAY.

Puede borrar de la memoria los canales que ya no

recibe o que ve muy raramente. (Por supuesto, puede

volver a agregar a la memoria los canales que haya

borrado de la misma.)

¡La bandeja se cerrará automáticamente y la repro-

ducción comenzará desde el primer capítulo o pista

del disco. Si la reproducción no comienza automáti-

camente, presione el botón PLAY.

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la pan-

talla.

1 Seleccione “AJUSTE DE CANAL”

Presione el botón SETUP del mando a distancia.

Presione el botón de flecha K o L para señalar

“AJUSTE DE CANAL”.

Presione el botón STOP para detener la

reproducción.

Luego, presione el botón ENTER.

–

_{Download from Www.Somanuals.co}5_m5_{. All Manuals Search And Download.}

0C28

Get it fixed, at your home or ours!

Your Home

For repair in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ^R(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.)

1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

Au Canada pour service en français:

1-800-LE-FOYER

1-888-SU-HOGAR

(1-800-533-6937)

(1-888-784-6427)

www.sears.ca

Registered Trademark / ^TMTrademark / ^SMService Mark of Sears, Roebuck and Co.

Marca Registrada / ^TMMarca de Fábrica / ^SMMarca de Servicio de Sears, Roebuck and Co.

^MCMarque de commerce / ^MDMarque déposée de Sears, Roebuck and Co.

FULL 90 DAY WARRANTY

For 90 days from the date of purchase, Sears will repair any defect in material or workmanship in this TV/DVD/VCR combina-

tion, free of charge. For one year from the date of purchase, Sears will supply, at no charge, replacement for defective parts.

Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

The above warranty coverage applies only to TV/DVD/VCR combination which are used for private household purposes.

TO OBTAIN WARRANTY SERVICE, SIMPLY RETURN THE TV/DVD/VCR COMBINATION TO THE NEAREST SEARS SER-

VICE CENTER IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179

For the location of a Sears Service Center in your area : 1-800-488-1222

Printed in Malaysia

0EMN02178

^{Download from Www.Somanuals.com. All Manuals Search And Dow}T^nlD^oa9^d4^.5UF/TD955UF ★★★★

Sharp Blu ray Player BD HP90U User Manual
Sharp MiniDisc Player MD MT877 User Manual
Sherwood Stereo Receiver R 525 User Manual
SIIG Network Card EVTEK 5103 User Manual
Sony Camcorder HXR MC1P User Manual
Sony DVD Player DRU 820A User Manual
Sony Home Theater System HTSS1000P User Manual
Standard Horizon Modem FVR1000 User Manual
Star Trac Treadmill 620 1045 User Manual
Sub Zero Refrigerator 315W User Manual