OWNER’S
MANUAL
COLOR TV/VCR
SRC2213B
SRC2319
13” MODEL ILLUSTRATED
This Owner’s Manual is made of
recycled paper.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR®
Partner, our company has
determined that this product meets
the ENERGY STAR® guidelines for
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
TOLL FREE : 1-800-968-3429.
energy efficiency. ENERGY STAR® is
a U.S. registered mark.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please read before using this equipment
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/VCR, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
19.Damage Requiring Service-Unplug this TV/VCR from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR.
c. If the TV/VCR has been exposed to rain or water.
d. If the TV/VCR does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/VCR to its normal operation.
14.Lightning-For added protection for this TV/VCR receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/VCR due to lightning and
power-line surges.
e. If the TV/VCR has been dropped or damaged in any way.
f. When the TV/VCR exhibits a distinct change in perfor-
mance-this indicates a need for service.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21.Safety Check-Upon completion of any service or repairs to
this TV/VCR, ask the service technician to perform routine
safety checks to determine that the TV/VCR is in proper
operating condition.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/VCR through openings as they may touch dan-
gerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/VCR.
22.Heat-This TV/VCR product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/VCR yourself
as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to quali-
fied service personnel.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
- 3 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
LOCATION
For safe operation and satisfactory performance of
your TV/VCR, keep the following in mind when
selecting a place for its installation:
Shield it from direct sunlight and keep it away
from sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top and bottom of the unit. Do not place the
unit on a carpet because this will block the ventila-
tion holes.
Unauthorized recording or use of broadcast televi-
sion programming, video tape, film or other copy-
righted material may violate applicable copyright
laws. We assume no responsibility for the unautho-
rized duplication, use, or other acts which infringe
upon the rights of copyright owners.
•
•
•
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the TV/VCR near strong magnetic fields.
Avoid moving TV/VCR to locations where temper-
•
•
•
•
ature differences are extreme.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
•
•
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/VCR cassette holder.
Do not place anything directly on top of the unit.
•
•
•
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a tape is played in a TV/VCR
which has moisture, it may damage the tape and
TV/VCR. Therefore when the condensation occurs
inside the unit, turn the POWER button on and allow
at least 2 hours for the unit to dry out.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Download from Www.Somanuals.c-om4.-All Manuals Search And Download.
EN
1K09
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .19
PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6
C OPERATING CONTROLS AND FUNCTIONS 7
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20
NORMAL RECORDING . . . . . . . . . . . . . . . . .20
SKIPPING UNWANTED SCENES DURING
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20
OTR (One Touch Recording) . . . . . . . . . . . . . .20
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21
TIMER PROGRAM EXTENSION . . . . . . . . .22
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9
ANTENNA/CABLE CONNECTIONS . . . . . . .9
INSTALLING THE BATTERIES . . . . . . . . . . .10
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10
CHANNEL SET UP FOR THE FIRST TIME .10
CLOCK SET UP (AUTO / MANUAL) . . . . . .11
CHANNEL SET UP AGAIN . . . . . . . . . . . . . .12
DELETING (OR ADDING) CHANNEL . . . . .12
SELECTING THE LANGUAGE . . . . . . . . . . .13
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .13
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25
REAL TIME TAPE COUNTER . . . . . . . . . . . .25
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14
WATCHING A TV PROGRAM . . . . . . . . . . . .14
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27
C CABLE CHANNEL DESIGNATIONS . . . . . .27
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
INDICE
CONTROLES DE OPERACIÓN Y
INSTALACIÓN DE LAS PILAS . . . . . . . . . . . . .30
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28
PREPARACIÓN DE CANALES POR
CONEXIONES DE ANTENA/CABLE . . . . . . . .30 PRIMERA VEZ . . . . . . . . . . . . . . . . . . . . . . . . . .31
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30 AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-
tions concerning chemical wastes.
- 5 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Infrared remote control
Bilingual on screen menu display selectable in
English or Spanish
Zero Return–The tape returns to counter of
•
•
•
•
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene. Only tapes recorded
in SLP mode will show a fairly clear picture.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the TV/VCR to advance
the tape by entering the desired playback time you
want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
1 Year, 8 events (including Daily and Weekly
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on dif-
ferent channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broad-
casts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Real time counter–This shows the elapsed record-
ing or playback time in hours, minutes, and sec-
onds. The “–” indication will appear when the tape
is rewound further than the tape counter position
“0:00:00”.
181 channel capability PLL frequency synthesiz-
er tuner with direct station call–(A converter may
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prere-
corded tapes, etc. with either a dialogue caption or
text display added to the program.
Game mode–Automatically sets external input
mode and allows TV/VCR display to be suitable
for use with TV games.
Auto power on and off system–Automatically
turns on the TV/VCR when you insert the cassette,
turns off after auto-rewind, and ejects when the
beginning of the tape is reached.
•
•
•
•
•
•
•
•
•
•
•
•
Auto rewind when the end of a tape is
reached–This function doesn’t occur when using
timer recording.
2 Step picture search operation–You can view a
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
Three different playback tape speeds : SP/LP/SLP
Two different recording tape speeds : SP/SLP
Auto Head Cleaner–Automatically cleans video
heads as you insert or remove a cassette.
Auto return–After timer recording is finished, the
TV/VCR can return to the beginning of the record-
ing.
Wake up/Sleep timer–Allows you to have the
TV/VCR automatically turn on or off at a desired
time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
•
•
•
•
•
•
•
•
•
SUPPLIED ACCESSORIES
Remote Control Unit
2 AA Batteries
Rod Antenna
(13” model only)
PART NO. (0EMN00673 or
PART NO. (N0154UD)
0EMN01599 or
0EMN01755)
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-
968-3429.
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control. If you decide to use a universal remote control with this unit, please be aware
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-
versal remote control.
•
•
•
Download from Www.Somanuals.c-om6.-All Manuals Search And Download.
EN
1K09
OPERATING CONTROLS AND FUNCTIONS
"
"
This manual covers 13 and 19 . The operation of the two models are exactly the same except
"
the appearance. 13 model is illustrated in this manual.
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
•
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- TV/VCR FRONT PANEL - [Fig.1]
VIDEO
AUDIO
POWER
VOLUME
CHANNEL
STOP/EJECT
REW
PLAY
F.FWD
REC/OTR
EARPHONE
1 2 3 4 5 6 7 8 910 11 12 1314
1 VIDEO input jack– Connect to the video output
- REMOTE CONTROL - [Fig.2]
jack of your video camera or another VCR.
2 AUDIO input jack– Connect to the audio output
jack of your audio equipment, video camera or
another VCR.
25
7
WAKE-UP
/SLEEP
POWER
EJECT
3 POWER button– Press to turn TV/VCR on and
off. Press to activate timer recording.
X Y
3
CHANNEL
RETURN
4 VOLUME
level.
/
buttons– Adjust the volume
1
4
7
2
5
8
3
6
9
24
5 CHANNEL K / L buttons– Press to select the
desired channels for viewing or recording.
You may display the main menu on the TV screen
by pressing repeatedly this button on the
TV/VCR.
TRACKING function– Press to minimize video
‘noise’ (lines or dots on screen) during playback
mode. (See page 19.)
6 Remote Sensor Window– Receives the infrared
signals from the remote control.
7 STOP / EJECT button (TV/VCR)– Press to stop
the tape motion. Press in the Stop mode to remove
tape from TV/VCR.
15
CHANNEL
VOLUME
5
4
0
+100
MENU
DISPLAY
MUTE
16
17
8
23
9
PLAY
10
REW
F.FWD
STOP
7
SPEED PAUSE/STILL
RECORD
22
21
11
18
T-PROG.
CLEAR
GAME
TIME SEARCH
STOP button (remote control)– Press to stop the
tape motion.
EJECT button (remote control)– Press to remove
tape from TV/VCR.
COUNTER
RESET
19
20
L button–
Press to select setting modes from the on screen
menu.
•
Press to enter digits when setting program.
(for example: setting clock or timer program)
•
- 7 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
- REAR VIEW - [Fig.3]
ANT.
26
27
+100 button– When selecting cable channels
which are higher than 99, press this button first,
then press the last two digits. (To select channel
125, first press the “+100” button then press “2”
and “5”).
8 REW button– Press to rewind the tape, or to view
the picture rapidly in reverse during playback
mode. (Rewind Search)
s button–
Press to select a mode from a particular menu.
•
16 MENU button– Press to display the main menu on
the TV screen.
17 DISPLAY button– Display the counter or the cur-
rent channel number and current time on the TV
screen. (See page 25.)
18 SPEED button– Press to choose the desired
recording speed:SP/SLP.
19 T-PROG. CLEAR button– Press to cancel a setting
of timer program. (See page 23.)
COUNTER RESET button– Press to reset counter
to 0:00:00.
20 GAME button– Set the game mode and external
input mode at the same time. (See page 14.)
21 TIME SEARCH button– Press to activate Time
Search mode.
22 PAUSE/STILL button– Press to temporarily stop
the tape during the recording or to view a still pic-
ture during playback.
23 MUTE button– Mutes the sound. Press it again to
resume sound.
24 CHANNEL RETURN button– Press to go back to
the previously viewed channel. For example,
pressing this button once will change channel dis-
play from 3 (present channel) to 10 (previously
viewed channel), and pressing it a second time
will return from 10 to 3.
25 WAKE UP/SLEEP button– Sets the Wake up or
Sleep Timer. (See page 23.)
26 Power cord– Connect to a standard AC outlet
(120V/60Hz).
(for example: LANGUAGE or USER’S SET UP)
9 PLAY button– Press to begin playback.
K button–
Press to select setting modes from the on screen
menu.
•
Press to enter digits when setting program.
•
(for example: setting clock or timer program)
10 F.FWD button– Press to rapidly advance the tape,
or to view the picture rapidly in forward during
playback mode. (Forward Search)
B button–
When setting program (for example: setting clock
•
or timer program), press to determine your selec-
tion and proceed to the next step you want to
input.
Press to determine setting modes from on screen
menu.
•
Press to select a mode from a particular menu.
•
(for example: LANGUAGE or USER’S SET UP)
11 REC button– Press for manual recording.
OTR button– Activates One Touch Recording.
(only on the TV/VCR)
12 RECORD indicator– Flashes during recording.
Lights up in the Stand-by mode for Timer
Recording.
13 EARPHONE jack– Connects to earphones (not
supplied) for personal listening. The size of jack is
1/8” monaural (3.5mm).
14 Cassette compartment
15 Number buttons– Press to select desired channels
for viewing or recording. To select channels from
1 to 9, first press the 0 button and then 1 to 9.
27 ANT. terminal– Connect to an antenna or cable
system.
Download from Www.Somanuals.c-om8.-All Manuals Search And Download.
EN
1K09
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
From Cable System or
Satellite Dish
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box
(Not supplied)
Rod Antenna
(Supplied with 13” model only)
OUT
IN
VHF Antenna
(Not supplied)
UHF Antenna
(Not supplied)
From
Cable System
or
ANT.
VHF/UHF
Combiner
(Not supplied)
or
or
ANT.
or
75-ohm Coaxial
Cable (Not supplied)
Flat twin-lead cable
VHF/UHF COMBINED ANTENNA
VHF/UHF SEPARATE ANTENNAS
The VHF/UHF Rod Antenna (supplied with 13”
In some areas it will be necessary to use an outdoor
model only) is detachable. Insert the stem of the anten- antenna.
na into the hole on the upper-back portion of the
CABLE WITHOUT CONVERTER/
TV/VCR. Connect the VHF/UHF Rod Antenna or
VHF/UHF Combination Antenna to the ANT. terminal
of the TV/VCR as shown in the diagram above. For
the best reception, fully extend the VHF/UHF Rod
Antenna and make the necessary adjustments. (Avoid
touching the top section when adjusting.)
NOTE:
Before plugging the Rod antenna into antenna termi-
nal, check that the pin is not bent. If it is bent,
straighten the pin as illustrated, then plug the pin into
antenna terminal.
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/VCR without a converter box.
By using this connection you can:
1) Use the TV/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This unit will ONLY record and view the
same channel.
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
Bent pin
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown here.
Cable Plug
By using this connection you can also record scram-
bled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR Remote Control. Unattended timer record-
ing is limited to one channel at a time.
(Straight pin)
(Needs to be straightened)
NOTE:
The connection of an indoor antenna may not always
give acceptable TV reception.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-
ed to the grounding system of the building as close to the point of cable entry as practical.
- 9 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
TO RECORD A SCRAMBLED/UNSCRAMBLED
CHANNEL
INSTALLING THE BATTERIES
1. Set the TV/VCR channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or
video camera), connect the player’s audio/video out-
put cables to the AUDIO IN/ VIDEO IN jacks of
your TV/VCR. Then press the CHANNEL K or
button until “AUX” appears on the screen.
NOTE: “AUX” is found below the
lowest memorized channel.
L
AUX
(Example: CH2)
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then
select the channel to be viewed on the Cable Box or Satellite Box.
The tuner scans and memorizes all active channels in
your area.
NOTES:
CHANNEL SET UP FOR THE
FIRST TIME
The TV/VCR distinguishes between standard TV
channels and cable channels.
•
1 Plug in the TV/VCR power cord
Plug the TV/VCR power cord into a
standard AC outlet.
If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
MENU button on the remote control. To preset the
tuner again, see “CHANNEL SET UP AGAIN” on
page 12.
The TV/VCR may memorize TV channels as
CATV channels if reception conditions are poor. If
this happens, try the AUTO MEMO action again
when reception conditions are better.
•
NOTE:
If some digits appear in the corner of
the screen, press the POWER button
without unplugging the power cord.
•
•
2 Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR
5 After scanning
3 Select “ENGLISH” or “ESPAÑOL”
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote
control number buttons or CHANNEL K or L.
– SET UP –
Select “ENGLISH” or
B
LANGUAGE
“ESPAÑOL”=Spanish using the
F.FWD/B or REW/s button. “[ ]”
indicate the selected language.
[ENGLISH] ESPAÑOL
AUTO PRESET
4 Begin auto preset
Press the PLAY/K or STOP/L but-
ton to point to “AUTO PRESET”.
Then press the F.FWD/B button.
– SET UP –
LANGUAGE
[ENGLISH] ESPAÑOL
B
AUTO PRESET
- 10 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
TO SELECT A DESIRED CHANNEL
4 Select the day
You can select the desired channel by using the
CHANNEL K or L button on or directly pressing
the number buttons on the remote control.
Note for using the number buttons:
– MANUAL CLOCK SET –
MONTH DAY YEAR
Press the PLAY/K or STOP/L but-
ton until your desired day appears.
(Example: 6th → 06)
0 5
/
0 6 – – – – – – –
HOUR
– –
MINUTE
– – – –
:
Then, press the F.FWD/B button.
When selecting cable channels which are higher
•
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
– MANUAL CLOCK SET –
MONTH DAY YEAR
5 Select the year
Press the PLAY/K or STOP/L but-
ton until your desired year appears.
(Example: 2003)
You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).
•
0 5
/
0 6 TUE 2 0 0 3
HOUR
– –
MINUTE
– – – –
:
Then, press the F.FWD/B button.
CLOCK SET UP
(AUTO / MANUAL)
6 Select the hour
Press the PLAY/K or STOP/L but-
ton until your desired hour appears.
(Example: 5, PM)
– MANUAL CLOCK SET –
MONTH DAY YEAR
The TV/VCR clock must be set correctly before
VCR timer recording is possible. It is suggested that
the clock be set manually when first setting up the
TV/VCR. Then, set to [on] the auto clock setting
which will periodically correct the setting if neces-
sary.
NOTE: If you cannot receive a station with time
signals, auto clock setting cannot be performed. Use
manual setting only.
0 5
/
0 6 TUE 2 0 0 3
HOUR
0 5
MINUTE
– – PM
:
Then, press the F.FWD/B button.
– MANUAL CLOCK SET –
MONTH DAY YEAR
7 Select the minute
Press the PLAY/K or STOP/L but-
ton until the desired minute
appears. (Example: 40)
0 5
/
0 6 TUE 2 0 0 3
HOUR
0 5
MINUTE
4 0 PM
:
MANUAL CLOCK SETTING
Make sure ...
8 Start the clock
5:40 PM
The TV/VCR is turned on.
In the example below, the clock is to be set to:
•
Press the MENU button on the
remote control.
DATE
May 6th, 2003
Although seconds are not dis-
played, they begin counting from
SETTING TIME 5:40PM
00 when you press the MENU button on the remote
control. Use this feature to synchronize the clock
with the correct time.
– M E N U –
1 Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L
button to point to “SETTING
CLOCK”.
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
NOTE:
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
ZERO RETURN
TIME SEARCH
Then, press the F.FWD/B button.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the
F.FWD/B or REW/s button.
3)Enter correct numbers using the PLAY/K or
STOP/L button.
– SETTING CLOCK –
2 Select “MANUAL CLOCK
SET”
Press the PLAY/K or STOP/L
button to point to “MANUAL
CLOCK SET”.
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
B
[OFF]
Then, press the F.FWD/B button.
4)Press the MENU button on the remote control to
start the clock.
– MANUAL CLOCK SET –
MONTH DAY YEAR
3 Select the month
PLEASE NOTE:
Press the PLAY/K or STOP/L
button until your desired month
appears. (Example: May → 05)
Then, press the F.FWD/B button.
0 5
/
– – – – – – – – –
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the F.FWD/B or REW/s button to turn [OFF]
this function. Then you can manually adjust the
clock.
HOUR
– –
MINUTE
– – – –
:
- 11 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC CLOCK SETTING
Make sure ...
NOTE: During Auto Clock CH Search, the picture
may be distorted. This is normal.
The TV/VCR is turned on.
Confirm the TV/VCR is receiving a RF (Radio
Frequency) signal from either an antenna or cable
system connection using the ANT IN jack on the
rear of the TV/VCR.
•
•
4 Enter the channel number that contains the
Automatic Clock Setting Signal
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L
button to select “SETTING
CLOCK”.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
NOTE:
If a cable converter box is being used, make sure it
is powered on.
•
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
You must use the TV/VCR remote control to per-
form the clock setting procedure.
If the TV/VCR is connected directly to a cable
converter box or satellite box, the local PBS station
must be selected on the cable box itself, and the
TV/VCR must be set to the output channel of the
cable converter box or satellite box (usually chan-
nel 3 or 4), to be able to set up or correct the clock
automatically
•
Press the F.FWD/B button to
select setting clock.
Press the STOP/L button to select
“AUTO CLOCK CH”.
Press the F.FWD/B or REW/s
buttons until you locate Auto
Clock Set station number. See item
3 above.
– SETTING CLOCK –
AUTO CLOCK
[ON]
•
AUTO CLOCK CH SEARCH
B
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[
45]
[OFF]
Press the MENU button to exit the screen.
1 Select “SETTING CLOCK”
5 Turn off the TV/VCR
Press the MENU button on the
Once the TV/VCR is turned off , it will periodically
check and set the correct date and time.
– M E N U –
remote control.
Press the PLAY/K or STOP/L but-
ton to select “SETTING CLOCK”.
Press the F.FWD/B button to enter
“SETTING CLOCK” menu.
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
CHANNEL SET UP AGAIN
TIME SEARCH
Make sure ...
Press the POWER button to turn on the TV/VCR.
– SETTING CLOCK –
•
2 Set “AUTO CLOCK” to [ON]
Press the F.FWD/B button until
AUTO CLOCK [ON] appears.
B
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
1 Select “CHANNEL SET UP”
[OFF]
– M E N U –
Press the MENU button on the
TIMER PROGRAMMING
PICTURE CONTROL
remote control.
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to “CHANNEL SET
UP”.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
3 Begin “AUTO CLOCK CH SEARCH”
Press the STOP/L button to select “AUTO CLOCK
TIME SEARCH
Then, press the F.FWD/B button.
CH SEARCH”.
Press the F.FWD/B button.
– SETTING CLOCK –
The TV/VCR is now searching
•
AUTO CLOCK
[ON]
2 Begin auto preset
B
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
– CHANNEL SET UP –
for the station which contain the
auto clock set signal. The search
for a signal may take up to 20
seconds per channel.
“_ _” appears at the lower left of
the screen when the search has
ended.
Press the PLAY/K or STOP/L but-
ton to point to “AUTO PRESET”.
Then, press the F.FWD/B button.
The tuner scans and memorizes all
the active channels in your area.
[OFF]
ADD / DELETE CH (TV)
AUTO PRESET
B
•
– AUTO CLOCK CH SEARCH –
08
10
13
3 After scanning
Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
station(s) in your area. See item
4 below.
If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 11.
•
The tuner stops on the lowest memorized channel.
_ _
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
•
Press the MENU button to exit the screen.
- 12 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “CHANNEL SET
UP”.
2 Select “ENGLISH” or “ESPAÑOL”
Select “ENGLISH” or “ESPAÑOL”= Spanish using
the F.FWD/B or REW/s button.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
3 Exit the Language mode
Press the MENU button on the remote control to
return to TV mode.
ZERO RETURN
TIME SEARCH
Then, press the F.FWD/B button.
NOTE: If for some reason the menu is in Spanish,
press the MENU button on the remote control, press
the PLAY/K button to point to “IDIOMA
[ESPAÑOL]”, then press the F.FWD/B button, then
press the MENU button on the remote control.
– CHANNEL SET UP –
2 Select “ADD/DELETE CH”
Press the PLAY/K or STOP/L but-
ton to point to “ADD/DELETE
CH”.
B
ADD / DELETE CH (TV)
AUTO PRESET
Press the F.FWD/B button.
DAYLIGHT-SAVING TIME
Select this feature and the TV/VCR’s clock automati-
cally will advance one hour in April, then reverse one
hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
First Sunday of April : At 2 AM the clock imme-
diately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
3 Enter the desired channel number
Press the PLAY/K or STOP/L but-
ton until your desired channel num-
ber appears. (You can also use the
number buttons or the CHANNEL
K/L button to enter it) (Example:
CH8)
08
ADD / DELETE
•
4 Delete (or add) it from (into) memory
Press the F.FWD/B or REW/s button. The channel
number changes to light red. The channel is deleted
from memory.
•
Make sure ...
Press the POWER button to turn on the TV/VCR.
To delete another channel, repeat steps [3] and [4].
If you press the F.FWD/B or REW/s button
again, the channel is memorized again.
•
•
•
1 Select “SETTING CLOCK”
Added channel: Light blue.
Deleted channel: Light red.
Press the MENU button on the
– M E N U –
remote control.
TIMER PROGRAMMING
PICTURE CONTROL
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to “SETTING
CLOCK”.
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
5 Exit the channel setup mode
Press the MENU button on the remote control to
returns to TV mode.
TIME SEARCH
Then, press the F.FWD/B button.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
2 Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the PLAY/K or STOP/L but-
– SETTING CLOCK –
ton to point to “D.S.T.”.
Then, press the F.FWD/B or
REW/s button until [ON] appears.
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
MANUAL CLOCK SET
D.S.T.
[ 02 ]
SELECTING THE LANGUAGE
Make sure ...
B
[ON]
Press the POWER button to turn on the TV/VCR.
NOTE: This function effects only the language on
the screen menu and not the audio source.
•
3 Exit the Daylight-Saving Time mode
Press the MENU button on the remote control to
return to TV mode.
1 Select “LANGUAGE”
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
Press the MENU button on the
remote control.
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to “LANGUAGE”.
B
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
F.FWD/B or REW/s button.
- 13 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
The TV/VCR’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
1 Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
2 Select the channel number
Press the CHANNEL K or L button to select your
desired channel number or press the number buttons
on the remote control.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be viewed must be selected
on the cable box or satellite box.
Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
•
When setting the Picture Control, the Game mode
will be cancelled.
•
Make sure ...
TV/VCR power must be turned on.
•
1 Select “PICTURE CONTROL”
3 Adjust sound
Press the VOLUME X or Y button
to adjust the volume.
Press the MENU button on the
– M E N U –
remote control.
TIMER PROGRAMMING
B
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
Press the PLAY/K or STOP/L but-
ton to point to ”PICTURE CON-
TROL”.
VOLUME 20
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
C
C
C
C
C
C
C
C
C
C
C
C
TIME SEARCH
Then, press the F.FWD/B button.
GAME MODE
2 Select item you want to adjust
Press the PLAY/K or STOP/L button until desired
This function enables you to decrease the TV screen
contrast and making it suitable for use with a TV
GAME.
control is displayed.
BRIGHT
CONTRAST
NOTE: This function can not be set during recording.
BRIGHT
COLOR
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
TINT
Press the GAME button on the
GAME
remote control. “GAME” appears
on the screen.
SHARPNESS
3 Adjust the picture control
When you press the GAME button;
Press the F.FWD/B or REW/s button to adjust to
The TV/VCR comes on automatically if it is off.
The TV/VCR will be in external input mode auto-
•
•
your desired level.
matically.
REW/s
to decrease
brightness
to decrease
contrast
F.FWD/B
to increase
brightness
to increase
contrast
BRIGHT
TO CANCEL THE GAME MODE
Press the GAME button or CHANNEL K or L but-
ton on the remote control.
CONTRAST
COLOR
TINT
SHARPNESS to soft
to pale
to brilliant
DEGAUSSING
Magnetism from nearby appliances might affect the
color of the TV picture.
If this happens, move this unit away from the appli-
ance. If the color is still not correct, disconnect
power cord from AC outlet then reconnect it after 30
minutes.
to purple
to green
to clear
If there is a power failure of any kind, the unit will
retain its memory for this feature.
•
- 14 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
F.FWD/B or REW/s button. Press the MENU but-
ton on the remote control to return to TV mode.
CLOSED CAPTION SYSTEM
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dia-
logue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
WHEN THE CLOSED CAPTION MODE IS ON
The On-Screen Display will disappear after 5 seconds.
This is also true when the MUTE button is pressed,
and when the PAUSE/STILL button is pressed
while recording.
•
If there is a power failure of any kind, the unit will
retain its memory for this feature.
•
V-CHIP SET UP
V-CHIP SET UP
Make sure ...
TV/VCR is turned on.
You have the TV/VCR remote control.
•
•
1 Select “V-CHIP SET UP”
– M E N U –
TIMER PROGRAMMING
Press the MENU button on the
PICTURE CONTROL
SETTING CLOCK
remote control.
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the PLAY/K or STOP/L but-
ton to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture ghosts
•
INDEX SEARCH
•
•
•
2 Enter Access code
Use the numbers on the remote
control to enter the access code.
ACCESS CODE
or airplane flutter.
_
_
_
_
Playback of poorly recorded or worn VCR tapes.
If the TV/VCR displays a black
box on the TV screen, this means
that the TV/VCR is set to the
TEXT mode. To clear screen,
select [CAPTION1], [CAPTION2]
or [OFF].
•
•
For the first time set-up or in the
event the TV/VCR has lost power,
•
enter the default code of the numbers: 0000.
– V-CHIP SET UP –
3 Select “TV RATING”
Press the PLAY/K or STOP/L but-
ton to select “TV RATING”.
Then, press the F.FWD/B button.
B
TV RATING
MPAA RATING
CHANGE CODE
Make sure ...
TV/VCR is turned on.
•
– M E N U –
1 Select “CAPTION”
TIMER PROGRAMMING
4 Blocking TV programs
Press the PLAY/K or STOP/L but-
ton to select “TV rating” that you
wish to block.
PICTURE CONTROL
Press the MENU button on the
SETTING CLOCK
CHANNEL SET UP
B
TV–Y
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
TV–Y7
TV–G
(
)
remote control.
Press the PLAY/K or STOP/L but-
ton to point to “CAPTION”.
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
TV–PG (
)
)
)
TV–14
(
B
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
TV–MA(
When you select the rating catego-
•
ry and turn it [BLOCK], the higher rating will turn
[BLOCK] automatically. Also, the lower rating will
turn [VIEW] automatically.
2 Select your desired caption
menu
Press the F.FWD/B or REW/s but-
ton until your desired caption menu
appears. ([CAPTION1], [CAP-
TION2], [TEXT1] or [TEXT2])
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
When you turn “TV-Y” to [VIEW], then all ratings
•
will turn to [VIEW] automatically.
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
B
TIME SEARCH
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7
TV-G
TV-PG
TV-14
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
3 Exit the caption setting mode
Press the MENU button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION SYSTEM
Repeat steps [1] and [2], select [OFF] using the
TV-MA Mature audience only
- 15 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
a station that is not protected. If the (PROTECTED)
appears on the screen, please change the channel to a
station that is not protected.
5 Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
1)Follow steps [1] and [2].
2)Press the F.FWD/B button to select "TV RAT-
ING". Select a TV rating to be unblocked by press-
ing the PLAY/K or STOP/L button.
Then press the F.FWD/B button to unblock the
rating.
V-CHIP SET UP SUB RATINGS
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
3)Press the MENU button on the remote control to
exit the screen.
1 Select “V-CHIP SET UP”
– M E N U –
TIMER PROGRAMMING
Press the MENU button on the
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
remote control.
USER’S SET UP
MPAA RATING SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the PLAY/K or STOP/L but-
ton to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
– M E N U –
1 Select “V-CHIP SET UP”
TIMER PROGRAMMING
INDEX SEARCH
PICTURE CONTROL
SETTING CLOCK
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
2 Enter Access code
Use the numbers on the remote con-
trol to enter the access code.
(Default code is 0000.)
ACCESS CODE
INDEX SEARCH
_
_
_
_
2 Enter Access code
Use the numbers on the remote con-
trol to enter the access code.
ACCESS CODE
– V-CHIP SET UP –
3 Select “TV RATING”
Press the PLAY/K or STOP/L but-
ton to select “TV RATING”.
Then, press the F.FWD/B button.
B
TV RATING
MPAA RATING
CHANGE CODE
_
_
_
_
– V-CHIP SET UP –
3 Select “MPAA RATING”
Press the PLAY/K or STOP/L but-
ton to point to “MPAA RATING”.
Then, press the F.FWD/B button.
TV RATING
MPAA RATING
CHANGE CODE
B
4 Selecting Sub-Ratings”
Press the STOP/L button to select
the sub-rating you wish to block.
Then, press the F.FWD/B button.
TV–Y7
FV
[BLOCK]
[BLOCK]
B
When you select [TV-Y7]:
Press the STOP/L or PLAY/K button to select
“FV” (Fantasy Violence).
Then, press the F.FWD/B button to select
[BLOCK] or [VIEW].
When you select [TV-PG], [TV-14] or [TV-MA]:
Press the STOP/L or PLAY/K
•
4 Select your desired item
Press the PLAY/K or STOP/L but-
ton to point to your desired item.
Then, press the F.FWD/B button to
select [BLOCK] or [VIEW].
G
[VIEW]
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
•
•
Selection
G
Rating Category Explanations
General Audience
button to select “D”(Suggestive
TV–PG
[BLOCK]
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Dialog), “L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
F.FWD/B button to select
[BLOCK] or [VIEW].
Note: When you select [TV-MA],
“D” does not appear on the TV
screen.
PG
PG-13
R
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
B
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
NC-17
X
(
)
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Mature audience only
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “G” to [VIEW], then all ratings
will turn to [VIEW] automatically.
•
•
The sub-ratings which set to [BLOCK] appears
next to the rating category in the TV rating menu.
5 Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
5 Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
CHANGING V-CHIP BLOCKED PRO-
GRAMMING
Note: To change the rating, the TV must be turned to
- 16 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGE ACCESS CODE
4 Enter New code
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
To change access code, follow the steps.
NEW CODE
X X X X
CONFIRM CODE
1 Select “V-CHIP SET UP”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to select “V-
CHIP SET UP”.
_
_
_
_
If you enter wrong code, repeat step 4, making sure
you enter the same new code exactly in the confirm
code space.
•
Then, press the F.FWD/B button.
ACCESS CODE
2 Enter Access code
Use the number on the remote con-
trol to enter the access code.
The default code is 0000.
_
_
_
_
5 Exit the V-Chip setting mode
Press the MENU button on the remote control to exit
the screen.
Note: If you unplug the power code or power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
– V-CHIP SET UP –
3 Select “CHANGE CODE”
Press the PLAY/K or STOP/L but-
ton to select "CHANGE CODE".
Then, press the F.FWD/B button.
TV RATING
MPAA RATING
CHANGE CODE
B
PLAYBACK
This TV/VCR will operate with any cassette that has the
mark. For best results, we
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
Avoid moisture. Moisture condensation may occur
•
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/VCR. The
TV/VCR will automatically turn on.
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/VCR, wait until the tape has warmed to
room temperature and the moisture has evaporated.
Window
Avoid extreme heat, high humidity and magnetic
fields.
•
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
•
WRONG
CORRECT
•
NORMAL PLAYBACK
AUTO REPEAT PLAYBACK
Make sure ...
The TV/VCR has the auto repeat function that allows
you to repeat a tape indefinitely without touching the
PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the begin-
ning to a blank part, which is blank for more than
10 seconds.
TV/VCR power must be turned on.
•
1 Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/VCR will start playback automatically.
2 To begin playback
B
PLAY
Press the PLAY button.
Note: If any menu is activated on
the screen, the PLAY button does
not function. Press the MENU but-
ton to clear the menu. then, press
the PLAY button.
1 Select “USER’S SET UP”
– M E N U –
TIMER PROGRAMMING
Press the MENU button on the
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
remote control.
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
STOP
3 To stop playback
Press the STOP button when play-
back is completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
- 17 -
EN
1K09
USER’S SET UP
–
–
2 Select “ALL” or “BLANK”
Press the PLAY/K or STOP/L but-
ton to point to “REPEAT PLAY”.
Press the F.FWD/B or REW/s
button repeatedly until your
1 Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
RENTAL
REPEAT PLAY
AUTO RETURN
[OFF]
[ALL]
[OFF]
B
2 Reset the counter to 0:00:00
Press the COUNTER RESET button repeatedly.
desired selection [ALL] or [BLANK] appears.
3 Exit the Repeat Play setting
3 Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback
is completed.
Press the MENU button on the remote control to
return to the TV mode.
4 Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR.
4 To activate “ZERO RETURN” mode
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to point to
“ZERO RETURN”.
•
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
•
Then, press the F.FWD/B button.
The counter will appear on the TV
screen.
LANGUAGE [ENGLISH]
The tape will automatically stop
CAPTION [OFF]
when the counter returns to
0:00:00.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
TO CANCEL THE REPEAT PLAY MODE
V-CHIP SET UP
B
ZERO RETURN
TIME SEARCH
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
TIME SEARCH
The Time Search function makes it possible to quick-
ly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
SEARCH
PICTURE SEARCH
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button during playback. (in the
SP / LP / SLP modes)
NOTES:
Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
•
This function will not operate in recording mode.
•
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
2)Press it again and the TV/VCR will now search in
super high speed. (in the LP / SLP modes only)
NOTE: Tapes recorded in the SP or LP mode will
display a noise bar on the TV screen and the pic-
ture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
1 Insert a tape.
2 Select “TIME SEARCH” mode
Press the TIME SEARCH button (with each push it
will increase by 10 minutes).
ZERO RETURN
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
3 Enter your desired time
Press the PLAY/K or STOP/L but-
TIME SEARCH
2 : 50
ton until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time
Search at this point, press the
MENU button on the remote control.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
- 18 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE CONTROLS
TRACKING ADJUSTMENT
Tracking adjustment will be set automatically
(Digital Tracking function) when you start play-
back.
4 Begin Time Search
By pressing the REW/s or F.FWD/B button, the
TV/VCR will rewind or fast forward to the specified
point.
•
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at
this point
Press the STOP/EJECT button on the TV/VCR or
the remote control. This will delete the selected
time.
However when playing pre-recorded tapes or tapes
•
recorded on units other than your own, noise lines
(black and white streaks) may appear on the play-
back picture. If this occurs, you can adjust the
tracking control manually by pressing the CHAN-
NEL K or L button until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
RENTAL PLAYBACK
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
STILL PICTURE
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE/STILL
button during playback. Only tapes recorded in the
SLP mode will show the least amount of lines.Press
the PLAY button to return to playback.
NOTES:
Usually there will be video “noise” lines (black
and white streaks or dots) on the screen. This is
normal.
1 Select “USER’S SET UP”
Press the MENU button on the
remote control.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
•
TIME SEARCH
If the tape was originally recorded in SP or LP
mode, the still picture will be black and white in
addition to the “noise” lines.
This is not a fault of the machine, but is a limi-
tation of a TV/VCR with 2 video heads.
USER’S SET UP
–
–
2 Set “RENTAL” to [ON]
Press the PLAY/K or STOP/L but-
ton to point to “RENTAL”.
Press the F.FWD/B or REW/s
button until [ON] appears.
B
RENTAL
REPEAT PLAY
AUTO RETURN
[ON]
[OFF]
[OFF]
If it is left in the Pause mode for more than five
•
minutes, the TV/VCR will automatically switch to
the Stop mode.
3 Exit the Rental setting
Press the MENU button on the remote control to
return to the TV mode.
NOISE CANCEL (in the Still mode)
4 Start playback
This feature allows you to reposition or reduce the
noise lines of a still picture. Press the PAUSE/STILL
button so that the noise lines change position on the
screen so you can see the picture in its entirety with-
out distracting noise lines.
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
Once you select the Rental mode, it stays in effect
even after you turn off the TV/VCR.
•
NOTE: This feature can be activated ONLY when
viewing a tape recorded in the SLP mode. If the tape
was originally recorded in the SP or LP mode, the
still picture may revert to black and white in addition
to the “noise bars”. This is normal.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
VERTICAL HOLD CONTROL
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL K or L button.
NOTE:
If there are video noise lines on the screen, reposition
or reduce them. Refer to “NOISE CANCEL”.
- 19 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
TWO DIFFERENT TAPE SPEEDS
ERASE PREVENTION
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/play-
back time using T60, T120 or T160 tapes in each
mode.
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
Tape Speed
Type of tape
SP mode
Recording/Playback Time
If you decide to record on
the tape again, cover the
hole with plastic tape.
T60
1 hour
3 hours
T120
T160
2 hours 2-2/3 hours
6 hours 8 hours
SLP mode
Note: You can play back a tape recorded in LP mode
(Long Play).
Make sure ...
Transparent Tape
TV/VCR power must be turned on.
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
•
•
NOTE: This unit will ONLY record and view the same channel.
SKIPPING UNWANTED
NORMAL RECORDING
You can ONLY watch the same TV program that is
being recorded.
SCENES DURING RECORDING
Press the PAUSE/STILL button to
PAUSE
temporarily stop recording.
Press the PAUSE/STILL or
RECORD button to resume record-
ing.
NOTES:
1 Select the channel to be recorded
SP
Press the number buttons on the
CH 10
remote control or the CHANNEL
K or L button.
Remember: If the TV/VCR is con-
nected to a cable box or satellite
box, the TV/VCR must be on CH3 or CH4, then the
channel to be recorded must be selected on the cable
box or satellite box.
After five minutes, the TV/VCR will automatically
switch to the Recording mode to prevent tape damage.
•
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then dis-
appear.
•
OTR (One Touch Recording)
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR.
2 Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
Make sure ...
TV/VCR power must be turned on.
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
•
•
3 Begin recording
Press the RECORD button.
REC
tape to the point at which you want to begin
recording.)
SP
NOTES:
This function CANNOT be done from the remote
control.
•
4 Stop recording
Press the STOP button when recording is completed.
Recording starts immediately when the REC/OTR
button is pressed.
•
When the REC/OTR button is pressed 18 times, the
TV/VCR returns to the Normal Recording mode.
•
- 20 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE:
July 4th, 2003
To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.
To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up
momentarily then disappear.)
Recording stops when 0:00 is reached.
Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours using
T-120).
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, ejects the tape and turns itself off.
If you press the power button during OTR, the
TV/VCR continues recording until the selected
length is reached.
•
•
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
TAPE SPEED:
Make sure ...
If a cable box or satellite box is connected with
the TV/VCR you will be limited to record only
one channel. And the channel selector on the
TV/VCR must be selected to the output channel of
the boxes CH 3 or CH 4 and then the actual chan-
nel to be recorded must be selected on the boxes.
Clock must be set to the correct time and date
before setting the timer.
TV/VCR power must be turn on to program it.
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
CH61
SP
•
•
•
•
•
•
•
•
The channel you want to record is properly set in
advance.
•
1 Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL K or L button.
Avoid over lap of programs ...
There is a chance that a program will not be record-
ed when programs overlap;
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.
The program with an earlier start has priority.
Once the earliest program finishes, the overlapping
•
•
programs will begin recording in sequence.
The illustration below demonstrates the sequence
of recordings.
•
2 Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
3 Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/VCR as many times as needed.
The recording length will be deter-
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
mined by the number of times you
SP
press the REC/OTR button. Each
additional push will increase the recording time by
30 minutes. It is set up to 8 hours.
1 Select “TIMER PROGRAMMING”
Press the MENU button on the
– M E N U –
B
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
Push(es) Display
1 push
Recording length
(normal recording)
remote control.
Confirm “TIMER PROGRAM-
MING” is pointed by pressing the
PLAY/K button.
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
2 pushes
3 pushes
0:30
1:00
30 minutes
60 minutes
ZERO RETURN
TIME SEARCH
And press the F.FWD/B button.
If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow stops [3] to
[8] on page 11. Then set the timer recording.
•
17 pushes
8:00
480 minutes
TIMER RECORDING
2 Select your desired program position (1~8)
You may set the TV/VCR to start and end a record-
ing while you are away. You can set 8 programs to
record on specific days, daily or weekly within a 1
year period.
– TIMER PROGRAMMING –
Press the PLAY/K or STOP/L but-
ton to select the desired program
position.
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
Then, press the F.FWD/B button.
In the following example, the timer is being set to record:
- 21 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Set the channel number
Press the PLAY/K or STOP/L but-
ton until the desired channel num-
ber appears.
(Example: CH61)
Then, press the F.FWD/B button.
8 Set end minute
– TIMER PROGRAMMING –
CH DATE BEGIN END
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the PLAY/K or STOP/L but-
ton until the desired minute
appears. (Example: “50” for
8:50PM)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PM- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
B
Then, press the F.FWD/B button.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.
– TIMER PROGRAMMING –
CH DATE BEGIN END
9 Set the tape speed
Press the PLAY/K or STOP/L but-
ton until the desired tape speed
appears. (Example: SP)
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:50PMSP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
4 Select once, every day or weekly recording
For once recording :
– TIMER PROGRAMMING –
Press the PLAY/K (up) button
10 Finish setting the program
CH DATE
BEGIN END
until the desired date appears.
(Example: “7/04” for July 4th).
Then, press the F.FWD/B but-
ton.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 7/04 FRI -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Press the F.FWD/B or REW/s button. The program
B
is now completed.
To set another program, repeat steps [2] to [10].
Press the MENU button on the remote control to
return to original mode.
•
•
For every day recording : To record a TV program at
the same time on the same channel every day.
(Example: Monday through Sunday) :
11 Set the timer
Press the POWER button to set automatic timer
recording. The RECORD indicator lights up.
– TIMER PROGRAMMING –
Press the STOP/L (down) button
CH DATE
BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY DAY -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
until “EVRY DAY” appears.
Then, press the F.FWD/B but-
ton.
B
You must turn off the TV/VCR to activate automat-
ic timer recording.
•
For weekly recording : To record a
If power is not turned off and you continue watch-
ing TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
TV program at the same time on the same channel
every week. (Example: every Monday) :
– TIMER PROGRAMMING –
Press the STOP/L (down) button
CH DATE
BEGIN END
until “EVRY” and your desired
day of the week appear together.
Then, press the F.FWD/B but-
ton.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
61 EVRY MON -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
B
TIMER PROGRAM EXTENSION
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
5 Set beginning hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the PLAY/K or STOP/L but-
ton until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the F.FWD/B button.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
2)Repeat step [1] on page 21.
61 7/04 FRI 7:12P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
3)Press the RECORD button and select the desired
program using the PLAY/K or STOP/L button.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the
PAUSE/STILL button on the remote control. The
recording time returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automat-
ically be set to the SLP mode.
6 Set beginning minute
Press the PLAY/K or STOP/L but-
ton until the desired minute
appears. (Example: “30” for
7:30PM)
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
Then, press the F.FWD/B button.
7 Set end hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the PLAY/K or STOP/L but-
ton until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the F.FWD/B button.
5)Press the F.FWD/B or REW/s button to exit the
setting menu. Then press the MENU button on the
remote control to return to original mode.
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30PM - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
61 7/04 FRI 7:30P
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
M
B
- 22 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CORRECT A PROGRAM
AUTO RETURN
While setting a program; press the REW/s but-
ton to go back one step and enter the correct num-
•
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
bers using the PLAY/K or STOP/L button.
After setting a program;
1)Press the POWER button.
•
1 Select “USER’S SET UP”
– M E N U –
2)Repeat steps [1] - [2] on page 21.
3)Press the F.FWD/B button (or press the
REW/s button to go back one step) until the
part you want to correct begins flashing, then
make the changes pressing the PLAY/K or
STOP/L button.
Press the MENU button on the
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
remote control.
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the PLAY/K or STOP/L but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
4)Press the POWER button to set automatic timer
recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
After setting a program;
1)Press the POWER button.
USER’S SET UP
–
–
2 Set “AUTO RETURN” to [ON]
Press the PLAY/K or STOP/L but-
ton to point to “AUTO RETURN”.
Press the F.FWD/B or REW/s
button until [ON] appears.
RENTAL
REPEAT PLAY
AUTO RETURN
[OFF]
[OFF]
[ON]
B
•
2)Repeat steps [1] ~ [2] on page 21 and select a
program you want to cancel.
3)Press the T-PROG. CLEAR button.
4)Press the MENU button on the remote control to
return to TV mode.
While recording is in progress;
1)Press POWER button.
3 Auto Return will begin
When all the timer recordings are completed, the
TV/VCR will rewind to the beginning of the recorded
program(s).
NOTE:
If you press the POWER button while tape is
rewinding, the Auto Return will stop.
•
•
2)Press the STOP/EJECT button on the TV/VCR.
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the REC indicator
goes off.
2)Press the MENU button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the F.FWD/B button. The details of pro-
grams appear on the TV screen.
5)Press the MENU button on the remote control to
return to TV mode.
4 Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
WAKE UP TIMER
The Wake Up Timer function turns on the TV/VCR
without using the POWER button after a desired
period of time.
HINTS FOR AUTOMATIC
TIMER RECORDING
Make sure the channel you want to record is prop-
erly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
•
NOTES:
•
Use the remote control for this procedure.
Clock must be set to the correct time before setting
•
•
•
•
the timer.
If you want to select [TAPE], you must insert a
cassette tape in the TV/VCR. The tape will start
playback automatically on your desired time.
•
not operate the unit manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
•
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, and the tape will be ejected.
1 Select “WAKE UP TIMER”
Press the WAKE UP/SLEEP button
on the remote control once, and
confirm “ON/OFF” is pointed.
Press the F.FWD/B or REW/s
button until [ON] appears.
•
WAKE UP B ON/OFF
[ON]
•
TIMER
TV/TAPE
TIME
[TV]
[12:00AM]
- 23 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
SLEEP TIMER
The Sleep Timer function turns off the TV/VCR
without using the POWER button after a desired
period of time.
2 Select “TV” or “TAPE”
Press the PLAY/K or STOP/L but-
ton until to point to “TV/TAPE”.
Press the F.FWD/B or REW/s
button, and select [TV] or [TAPE].
WAKE UP
TIMER
ON/OFF
B TV/TAPE
TIME
[ON]
[TV]
[12:00AM]
NOTE:
This function does not operate during Recording
•
mode.
3 Set wake up time
1 Select “SLEEP TIMER”
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
Press the PLAY/K or STOP/L but-
ton until to point to “TIME”.
Press the F.FWD/B or REW/s
button until your desired wake up
time appears.
WAKE UP
TIMER
ON/OFF
TV/TAPE
B TIME
[ON]
[TV]
[12:00AM]
2 Set sleep time
Press the PLAY/K, STOP/L,
F.FWD/B or REW/s button until
Each additional push will increase (or decrease) the
time by 10 minutes.
your desired sleep time appears.
SLEEP TIMER [2:00]
4 Exit the Wake Up Timer setting
Press the MENU button on the remote control to
return to TV mode.
Each additional push will increase
the time by 30 minutes up to 120 minutes.
Press the MENU button on the remote control to exit
the Sleep Timer setting.
TO CANCEL THE WAKE UP TIMER
Repeat step [1] but select [OFF].
TO CANCEL THE SLEEP TIMER
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
To view the time left for sleep timer press the WAKE
UP/SLEEP button twice, then press the MENU but-
ton on the remote control to exit the sleep timer set-
ting.
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends
or relatives for your enjoyment.
Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record onto into the TV/VCR’s cassette compart-
ment. This will become the copy.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
[Fig.8]
3)Press the SPEED button on remote control for the
TV/VCR to select the desired recording speed
(SP/SLP).
[The TV/VCR]
VIDEO
AUDIO
4)Press the CHANNEL K or L button on the
TV/VCR until “AUX” appears on the screen.
NOTE: “AUX” is found below the lowest memo-
rized channel. (Example: CH2)
5)Press the RECORD button on the TV/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
[Ex: Source (playing)
VCR or camcorder]
NOTE: For best results during dubbing, use the
TV/VCR’s front panel controls whenever possible.
The remote control might affect the source (Playing)
VCR’s playback operation.
AUDIO
Audio/Video
adapter cable
(not supplied)
OUT
IN
VIDEO
- 24 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
WHEN THE CLOSED CAPTION MODE IS OFF:
<Off mode>
<Counter mode>
<Clock mode>
Counter mode: After 5 seconds, only
the counter remains. To clear it, press
the DISPLAY button.
Clock mode: After 5 seconds, only
the clock and the channel number
remain. To clear them, press the DIS-
PLAY button.
•
•
5:40PM
CH2
Press
once
Press
once
COUNT 0:12:34
Press once
ON:
OFF mode
Clock/Counter mode
WHEN THE CLOSED CAPTION MODE IS
The On Screen Display disappear after 5 seconds.
•
STOP
5:40 PM
CH2
This is true even if the MUTE button is pressed, or the
PAUSE/STILL button is pressed while recording.
•
SP
COUNT 0:12:34
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change on a blank tape or blank portions on
the tape.)The “–” indication will appear when the
tape has rewound further than “0:00:00” on the tape
counter.
When the end of a tape is reached during record-
ing, playback, or fast-forward, the tape will auto-
matically rewind to the beginning. After rewinding
finishes, the TV/VCR will eject the tape and turn
itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
•
•
•
The tape will not auto-rewind during timer record-
ing or One Touch Recording.
MAINTENANCE
back, the video heads in your TV/VCR may need
to be cleaned.
CABINET CLEANING
Wipe the front panel and other exterior surfaces of
the TV/VCR with a soft cloth immersed in luke-
warm water and wrung dry.
•
1.Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the prob-
lem, please call our help line at 1-800-488-1222, to
locate an Authorized Service Center.
NOTES:
Remember to read the instructions included with
the video head cleaner before use.
Clean video heads only when problems occur.
Never use a solvent or alcohol. Do not spray insec-
•
ticide liquid near the TV/VCR. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
•
AUTO HEAD CLEANING
•
Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
•
SERVICING
Should your TV/VCR become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800-
488-1222, to locate an Authorized Service Center.
Playback picture may become blurred of interrupt-
•
•
ed while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
- 25 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to
remedy the problem.
PROBLEM
CORRECTIVE ACTION
Make sure the AC cord is connected to an AC outlet.
Make sure the power is turned on.
Make sure the AC cord is connected to an AC outlet.
Check antenna connection.
Program TV channels into TV/VCR.
Adjust direction or replace antenna.
Adjust picture controls.
Adjust volume control on remote control or main unit.
Press the MUTE button to restore sound.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the TV/VCR clock is set correctly.
Make sure the tape has an erase-prevention tab. If need, cover the
hole with plastic tape.
Adjust tracking control for a better picture using the CHANNEL
or L button on the TV/VCR.
Head cleaning may be necessary. Refer to “AUTO HEAD
CLEANING” on page 25.
Make sure the AC cord is connected to an AC outlet.
Check batteries in remote control.
You can not copy a copyrighted video tape. You are experiencing
copy guard protection.
Magnetism from nearby appliances or unshielded stereo speaker or
geomagnetism might affect the color of the TV picture. Move the
TV/VCR away from the appliances, the TV/VCR can repair itself
automatically. If you want to repair immediately, unplug the
TV/VCR power cord, then plug it in again 30 minutes or so later.
No power.
•
•
•
•
•
No picture and sound.
No picture or poor picture on
TV/VCR.
No sound or poor sound.
•
•
•
•
•
•
•
Timer recording is not possible.
Cannot go into Record mode.
•
•
Playback picture is partially noisy.
K
•
•
No picture but the audio is OK in
playback.
No operation by infrared Remote
Control.
Video or color fades in and out
when making a copy of a video tape
•
•
•
•
•
•
.
Different color marks on screen.
•
CLOSED CAPTION PROBLEM
My TV/VCR is showing captions
that are misspelled.
POSSIBLE REMEDY
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue
in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies
what is being said.
• can display a dialogue to a maximum of 220 words per minute. If a
• dialogue exceeds that rate, selective editing is used to insure that the
• captions remain up-to-date with the current TV screen dialogue.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My captions are scrambled with
white boxes on the TV screen.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box • company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
on certain channels.
• You are in the TEXT mode. Select CAPTION mode to CAPTION
• [OFF].
- 26 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
CRT :
13 or 19 inch in-line gun, 90˚
deflection tube
NTSC-M
Video input level :
Audio input level :
0.5~2.0Vp-p
-15dBs
Television system :
Closed caption system :§15.119/FCC
Video S/N ratio : More than 46dB
Audio S/N ratio : More than 43dB
Video Heads :
Tape width :
Tape speed
SP :
LP :
SLP :
Tuner channel
TV VHF Low :
TV VHF High :
TV UHF :
CATV
Rotary two-head
1/2 inch
OTHER SPECIFICATIONS
[ 13 inch model ]
Power requirement : AC 120V/60Hz
Power consumption : 65W
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
Dimensions :
H:15-3/8” (389mm)
W:14-1/2” (367mm)
D:14-7/8” (377mm)
23.1 lbs (10.5kg)
#2~#6
#7~#13
#14~#69
Weight :
[ 19 inch model ]
Power requirement : AC 120V/60Hz
Power consumption : 80W
VHF :
5A
MID band :
SUPER band :
HYPER band :
Terminals
A5~A1, A~I
J~W
W+1~W+84
Dimensions :
H:19-1/2” (493mm)
W:19-3/8” (491mm)
D:18-3/4” (475mm)
43.0 lbs (19.5kg)
Weight :
Antenna input :
VHF/UHF 75 ohms
unbalanced
Video input :
Audio input :
Earphone :
RCA connector [ 1
RCA connector [ 1
1/8” monaural (3.5 mm)
Designs and specifications are subject to change
without notice and without our legal obligation.
If there is a discrepancy between languages, the
default language will be English.
•
•
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
B
14
15
CATV channel
TV Display
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CATV channel
R
S
T
U
V
W
W+1
37
W+2
38
W+3
39
W+4
40
W+5
41
W+6
42
W+7
43
W+8
44
W+9
45
TV Display
31
32
33
34
35
36
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
CATV channel
TV Display
CATV channel
TV Display
76
77
78
79
80
81
82
83
84
85
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
86
87
88
89
90
W+55 W+56 W+57 W+58
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
CATV channel
TV Display
91
92
93
94
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
106
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CATV channel
TV Display
- 27 -
EN
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLES DE OPERACIÓN Y SUS FUNCIONES
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exac-
tamente la misma. En este manual se muestra el modelo de 13".
NOTA:
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del
mando a distancia universal.
VIDEO
AUDIO
POWER
VOLUME
CHANNEL
STOP/EJECT
REW
PLAY
F.FWD
REC/OTR
EARPHONE
1 2 3 4 5 6 7 8 910 11 12 1314
X
Y
)–
4 Botones de volumen (VOLUME
/
Ajustan el nivel del volumen.
25
7
5 Botones de canales (CHANNEL K/ L)–
Púlselos para seleccionar los canales deseados
para ver o grabar.
WAKE-UP
/SLEEP
POWER
EJECT
3
CHANNEL
RETURN
Se puede mostrar el menú principal en la pantalla
del televisor pulsando repetidamente este botón del
televisor/videograbadora.
1
4
7
2
5
8
3
6
9
24
Función de seguimiento– Pulse los botones
para minimizar el ruido de vídeo (líneas o puntos
en la pantalla) durante la reproducción.
6 Ventanilla sensora del mando a distancia–
Recibe las señales infrarrojas procedentes del
mando a distancia.
15
CHANNEL
VOLUME
5
4
0
+100
MENU
DISPLAY
MUTE
16
17
8
7 Botón L–
23
9
Púlselo para seleccionar los modos de ajuste
desde el menúde la pantalla.
•
PLAY
10
REW
F.FWD
Púlselo para introducir dígitos cuando establezca
un programa.
•
STOP
7
SPEED PAUSE/STILL
RECORD
(Por ejemplo: Para ajustar el reloj o establecer un
programa de temporizador)
[ Televisor/videograbadora ]
Botón de parada/expulsión (STOP/EJECT)–
Púlselo para detener la cinta. Púlselo en el modo
de parada para expulsar la cinta del
televisor/videograbadora.
22
21
11
18
T-PROG.
CLEAR
GAME
TIME SEARCH
COUNTER
RESET
19
20
[ Control remoto ]
Botón de parada (STOP)– Púlselo para deten-
1 Toma de entrada de vídeo (VIDEO)–
er la cinta.
Conéctela a la toma de salida de vídeo de su
videocámara u otra videograbadora.
Botón de expulsión (EJECT)–Púlselo para
expulsar la cinta del televisor/videograbadora.
2 Toma de entrada de audio (AUDIO)–
Conéctela a la toma de salida de audio de su equipo
de audio, videocámara u otra videograbadora.
3 Botón de la alimentación (POWER)–
Púlselo para encender y apagar el
8 Botón de rebobinado (REW)– Púlselo para
rebobinar la cinta, o para ver la imagen en retro-
ceso rápido durante el modo de reproducción.
(Búsqueda con rebobinado)
Botón s–
televisor/videograbadora. Púlselo para activar la
grabación con temporizador.
Púlselo para seleccionar un modo desde un menú
•
particular.
- 28 -
ES
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
ANT.
26
27
(Por ejemplo: IDIOMA o ADJUST DE USER)
9 Botón de reproducción (PLAY)– Púlselo
para iniciar la reproducción.
99, pulse primero este botón, y luego pulse los
dos últimos dígitos. (Para seleccionar el canal
125, pulse primero el botón “+100” y luego el
“2” y el “5”.)
Botón K–
16 Botón de menú (MENU)– Púlselo para visu-
alizar el menú principal en la pantalla del televi-
sor.
17 Botón del visualizador (DISPLAY)–
Visualiza el contador o el número del canal actu-
al y la hora actual en la pantalla del televisor.
18 Botón de velocidad de cinta (SPEED)–
Púlselo para elegir la velocidad de grabación
deseada: SP/SLP.
Púlselo para seleccionar los modos de ajuste
•
•
desde el menú de la pantalla.
Púlselo para introducir dígitos cuando establezca
un programa.
(Por ejemplo: Para ajustar el reloj o establecer un
programa de temporizador)
10 Botón de avance rápido (F.FWD)– Púlselo
para avanzar rápidamente la cinta, o para ver la
imagen en avance rápido durante el modo de
reproducción. (Búsqueda con avance rápido)
Botón B–
19 Botón T-PROG. CLEAR– Púlselo para cance-
lar un programa de temporizador.
Botón de reposición del contador
(COUNTER RESET)– Púlselo para reponer el
contador a 0:00:00.
Cuando establezca un programa (por ejemplo:
para ajustar el reloj o para establecer un progra-
ma de temporizador), púlselo para determinar su
elección y vaya al paso siguiente que quiera
introducir.
•
20 Botón de juego (GAME)– Establece el modo
del juego y el modo de entrada externa al mismo
tiempo.
21 Botón de búsqueda con tiempo (TIME
SEARCH)– Púlselo para activar el modo de
búsqueda con tiempo.
Púlselo para determinar los modos de ajuste
desde el menúde la pantalla.
Púlselo para seleccionar un modo desde un
menúparticular.
•
•
22 Botón de pausa/imagen fija
(Por ejemplo: IDIOMA o ADJUST DE USER)
(PAUSE/STILL)– Púlselo para detener tempo-
ralmente la cinta durante la grabación o para ver
una imagen fija durante la reproducción.
23 Botón de silenciamiento (MUTE)– Silencia
el sonido. Púlselo de nuevo para recuperar el
sonido.
11 Botón de grabación (REC)– Púlselo para ini-
ciar la grabación manual.
Botón de grabación de un toque (OTR)–
Activa la grabación de un toque. (Sólo en el tele-
visor/videograbadora)
12 Indicador de grabación (RECORD)–
24 Botón de retorno de canal (CHANNEL
RETURN)– Púlselo para volver al canal anterior.
Por ejemplo, pulsando una vez este botón, la
visualización del canal cambiará de 3 (canal actu-
al) a10 (canal anterior), y al pulsarlo por segunda
vez, el canal cambiará del 10 al 3.
25 Botón del temporizador despertador/para
dormir (WAKE UP/SLEEP)– Ajusta el tempo-
rizador para despertarse/dormir.
Parpadea durante la grabación.
Se enciende en el modo de espera de la grabación
con temporizador.
13 Toma de auriculares (EARPHONE)– Para
conectar los auriculares (no suministrados) y
escuchar en privado. La toma es mono y tiene un
tamaño de 1/8”(3.5 mm).
14 Compartimiento del videocasete
15 Botones numerados– Púlselos para selec-
cionar los canales deseados para ver o grabar.
Para seleccionar canales del 1 al 9, pulse primero
el botón 0 y luego el botón 1 a 9.
26 Cordón de alimentación– Conéctelo a la
toma de CA estándar (120V/60Hz).
27 Terminal de antena (ANT.)– Para conectar
una antena o sistema de televisión por cable.
Botón +100– Cuando seleccione canales de
televisión por cable cuyo número sea superior al
- 29 -
ES
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIONES DE ANTENA/CABLE
Desde el cable coaxil o
caja de emisiones vía
satélite de 75 ohm del
sistema de Cable
Caja de CATV
o caja de emi-
siones vía satélite
(no incluído)
Antena combinada de
VHF/UHF
(no incluído)
Antena de varilla UHF/VHF
(incluído para solamente 13”)
OUT
IN
Antena VHF
(no incluído)
Desde el
sistema de Cable
Antena UHF
(no incluído)
O
ANT.
Combinador de
VHF/UHF
(no incluído)
O
ANT.
Cable coaxil
de 75 ohm (no incluído)
O
Cable bifilar plano
O
de los canales deberá hacerse con el convertidor de tele-
visión por cable con el convertidor de emisiones vía
satélite. Esto significa que los canales no podrán ser
cambiados con el mando a distancia del
televisor/videograbadora. La grabación inatendida se
limita a un canal cada vez.
PARA GRABAR UN CANAL
CODIFICADO/DESCODIFICADO
1. Ajuste el selector de canales del
ANTENA COMBINADA DE VHF/UHF
La antena de varilla de VHF/UHF (incluído para sola-
mente 13”) es desmontable. Inserte el vástago de la
antena en el agujero de la parte trasera superior del tele-
visor/videograbadora.
Conecte la varilla de antena de VHF/UHF o la antena
combinada de VHF/UHF al terminal ANT. del televi-
sor/videograbadora.
televisor/videograbadora al canal de salida del con-
vertidor de televisión por cable o del convertidor de
emisiones vía satélite. (Ej.: CA3)
2. Seleccione el canal que desee grabar de su conver-
tidor de televisión por cable o del convertidor de emi-
siones vía satélite.
ANTENAS SEPARADAS DE VHF/UHF
En algunos lugares será necesario utilizar una antena
exterior.
CABLE SIN CONVERTIDOR/DESCODIFI-
CADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su
MODO DE ENTRADA EXTERNA
televisor/videograbadora sin convertidor.Utilizando esta
conexión usted podrá:
1)Utilizar el mando a distancia del
televisor/videograbadora para seleccionar canales.
2)Programar uno o más canales sin codificar para
realizar la grabación automática con temporizador.
NOTA: Con esta unidad SÓLO se podrá grabar y ver
un mismo canal al mismo tiempo.
Cuando utilice una señal de entrada externa (otra
videograbadora o una videocámara), conecte los cables
de salida de audio/vídeo del equipo de reproducción a las
tomas AUDIO IN/VIDEO IN de su
televisor/videograbadora. Y luego pulse el botón CHAN-
NEL K o L hasta que “AUX” aparezca en la pantalla.
Usted puede programar el temporizador para que explore
todos los canales que puedan recibirse en su zona.
CABLE CON CONVERTIDOR/DESCODIFI-
CADOR O CONVERTIDOR DE EMISIONES VÍA
SATÉLITE
Si su servicio de televisión por cable le suministra un
convertidor, o si usted utiliza un sistema de emisiones
vía satélite, usted podrá utilizar las conexiones básicas
mostradas aquí.
INSTALACIÓN DE LAS PILAS
1)Abra la tapa del compartimiento de las pilas del mando
a distancia presionándola en el sentido de la flecha.
2)Inserte 2 pilas tamaño “AA” en el compartimiento de las
pilas, en el sentido indicado por las marcas de polaridad
(+/-).
Utilizando estas conexiones, usted también podrá
grabar canales codificados. Sin embargo, la selección
3)Vuelva a poner la tapa.
- 30 -
ES
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARACIÓN DE CANALES POR
PRIMERA VEZ
1)Enchufe el cable de alimentación del
televisor/videograbadora en una toma de CA están-
dar.
NOTA: Si aparezcan algunos digitos en el rincón de
la pantalla, pulse el botón POWER sin desenchufar
el cable de alimentación.
2)Pulse el botón POWER para encender el televi-
sor/videograbadora.
3)Seleccione “ENGLISH” o “ESPAÑOL” utilizando
el botón F.FWD/B o REW/s. “[ ]” indica el
idioma seleccionado.
4)Pulse el botón PLAY/K o STOP/L para señalar
“AUTOPRESELECCION”.
AJUSTE DEL RELOJ
Cerciórese...
La alimentación del televisor/videograbadora
deberá estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 6 de mayo de 2003
HORA: 5:40 PM
1)Pulse el botón MENU en el mando a distancia.
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE RELOJ”.
Luego, pulse el botón F.FWD/B.
2)Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE MANUAL RELOJ”.
•
Luego, pulse el botón F.FWD/B.
3)Pulse el botón PLAY/K o STOP/L hasta que
aparezca el mes deseado. (Ejemplo: Mayo - 05)
Luego, pulse el botón F.FWD/B.
Luego pulse el botón F.FWD/B. El sintonizador
explorará y memorizará todos los canales activos
de su área.
NOTAS:
4)Pulse el botón PLAY/K o STOP/L hasta que
aparezca el día del mes deseado. (Ejemplo: 6 - 06)
Luego, pulse el botón F.FWD/B.
5)Pulse el botón PLAY/K o STOP/L hasta que
aparezca el año deseado. (Ejemplo: 2003)
Luego, pulse el botón F.FWD/B.
6)Pulse el botón PLAY/K o STOP/L hasta que
aparezca la hora deseada. (Ejemplo: 5, PM)
Luego, pulse el botón F.FWD/B.
7)Pulse el botón PLAY/K o STOP/L hasta que
aparezca el minuto deseado. (Ejemplo: 40)
8)Pulse el botón MENU en el mando a distancia.
Aunque los segundos no se visualizan, éstos
empiezan a contar desde 00 cuando se pulsa
MENU en el mando a distancia. Utilice esta fun-
ción para sincronizar el reloj con la hora correcta.
El televisor/videograbadora distingue entre los
canales de televisión estándar y los canales de tele-
visor por cable.
•
Si desea reproducir o grabar una cinta ANTES de
preajustar el sintonizador, usted tendrá que pulsar
el botón MENU en el mando a distancia. Para
preajustar de nuevo el sintonizador, consulte
“REPETICIÓN DE LA PREPARACIÓN DE
CANALES”.
•
La unidad de televisor/videograbadora puede
reconocer los canales de TV como ellos de TV por
cable a causa de los condiciones de recepción. En
este caso, pruebe el preajuste automático de nuevo
en los condiciones finas de recepción.
•
5)El sintonizador se para en el canal memorizado
más bajo. Si desea recuperar canales selecciona-
dos, usted podrá seleccionar directamente el canal
deseado con los botones numerados del mando a
distancia o con los botones CHANNEL K o L.
- 31 -
ES
1K09
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair in your home-of all major brand appliances,
-
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME R (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
MC
1-800-LE-FOYER
SM
1-888-SU-HOGAR
(1-800-533-6937)
(1-888-784-6427)
Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co.
Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.
R
R
MC Marque de commerce / MD Marque déposée de Sears, Roebuck and Co.
© Sears, Roebuck and Co.
LIMITED 90 DAY WARRANTY FOR 13 INCH MODEL
If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date of
purchase, return it to your nearest Sears store, and it will be replaced free of charge.
This warranty applies only if this (product) is used for private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
FULL 90 DAY WARRANTY FOR 19 INCH MODEL
For 90 days from the date of purchase, Sears will repair any defect in material or workmanship in this TV/VCR
combination, free of charge. For one year from the date of purchase, Sears will supply, at no charge, replacement
for defective parts.
Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
The above warranty coverage applies only to TV/VCR combination which are used for private household purposes.
TO OBTAIN WARRANTY SERVICE, SIMPLY RETURN THE TV/VCR COMBINATION TO THE NEAREST SEARS
SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179
For the location of a Sears Service Center in your area : 1-800-488-1222
Printed in Malaysia
0EMN02083
T5407UH / T7408UJ * * * * *
Download from Www.Somanuals.com. All Manuals Search And Download.
|