Sylvania TV VCR Combo 6719DF User Manual

OWNER’S

MANUAL

COLOR TV/VCR/DVD TRIPLE COMBO

(19 inch)

6719DF

INSTRUCCIONES EN ESPAÑOL INCLUIDAS

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.SylvaniaConsumerElectronics.com

Please read before using this equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding - If an outside antenna or

cable system is connected to the unit, be sure the antenna

or cable system is grounded so as to provide some protec-

tion against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. (Fig. A)

19.Damage Requiring Service - Unplug this unit from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the oper-

ating instructions. Adjust only those controls that are cov-

ered by the operating instructions, as improper adjustment

of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the unit to its normal operation.

14.Lightning - For added protection for this unit receiver during

a lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and dis-

connect the antenna or cable system. This will prevent dam-

age to the unit due to lightning and power-line surges.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance,

this indicates a need for service.

15.Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts - When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same characteris-

tics as the original part. Unauthorized substitutions may result

in fire, electric shock, injury to persons or other hazards.

21.Safety Check - Upon completion of any service or repairs

to this unit, ask the service technician to perform routine

safety checks to determine that the unit is in proper operat-

ing condition.

16.Overloading - Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry - Never push objects of any

kind into this unit through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the unit.

22.Heat - This unit product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

18.Servicing - Do not attempt to service this unit yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

- 3 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS

LASER SAFETY

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision. Reverse engineering or dis-

assembly is prohibited.

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

RADIO-TV INTERFERENCE

This Class B digital apparatus complies with

Canadian ICES-003.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or inciner-

ated but disposed of in accordance with your local

regulations concerning chemical wastes.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other unit has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

LOCATION

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a DVD is played in a unit which has

moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the unit on and allow at least 2 hours for the

unit to dry out.

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the unit near strong magnetic fields.

Avoid moving the unit to locations where tempera-

ture differences are extreme.

Be sure to remove disc and unplug the AC power

cord from the outlet before carrying the unit.

•

TV/VCR

: Description refers to TV/VCR operation (in the

TV/VCR mode).

•

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

: Description refers to playback of Audio CDs

(in the DVD mode).

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

QUICK

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

•

Do not put your fingers or objects into the unit disc

loading tray.

•

Do not place anything directly on top of the unit.

•

SUPPLIED ACCESSORIES

Remote Control Unit

Batteries

Owner’s Manual

Owner's Manual

NE209UD

2 AA Batteries

1EMN20670

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our

help line mentioned on the front page.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

•

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . .2

C SPECIAL PLAYBACK . . . . . . . . . .24

RENTAL PLAYBACK . . . . . . . . . .24

AUTO REPEAT PLAYBACK . . . . .24

C SEARCH FUNCTION . . . . . . . . . . .37

TRACK SEARCH . . . . . . . . . . . . .37

TITLE / CHAPTER SEARCH . . . .37

TIME SEARCH . . . . . . . . . . . . . . .37

MARKER SETUP SCREEN . . . . . .37

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

C SEARCH . . . . . . . . . . . . . . . . . . . . .25

ZERO RETURN . . . . . . . . . . . . . . .25

WARNING . . . . . . . . . . . . . . . . . . . .5

PICTURE SEARCH . . . . . . . . . . . .25

TIME SEARCH . . . . . . . . . . . . . . .25

INDEX SEARCH . . . . . . . . . . . . . .26

SPECIAL PLAYBACK FUNCTION . . .38

REPEAT . . . . . . . . . . . . . . . . . . . . .38

PROGRAM . . . . . . . . . . . . . . . . . . .38

RANDOM PLAYBACK . . . . . . . . .38

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C SUPPLIED ACCESSORIES . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C SPECIAL FEATURES . . . . . . . . . .27

REAL TIME TAPE COUNTER . . .27

AUTO REWIND-EJECT . . . . . . . .27

C CHANGING THE SETTINGS . . . .39

SUBTITLE LANGUAGE . . . . . . . .39

AUDIO LANGUAGE . . . . . . . . . . .39

STEREO SOUND MODE . . . . . . . .39

CAMERA ANGLE . . . . . . . . . . . . .40

BLACK LEVEL SETTING . . . . . . .40

VIRTUAL SURROUND . . . . . . . . .40

C RECORDING . . . . . . . . . . . . . . . . .28

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . . . . .9

NORMAL RECORDING . . . . . . . .28

INSTALLING THE BATTERIES . .11

SKIPPING UNWANTED SCENES

DURING RECORDING . . . . . . . . .28

C PREPARATION FOR USE . . . . . . .12

OTR (One Touch Recording) . . . . . .29

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .12

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .29

THE ON-SCREEN INFORMATION . .41

CONNECTING TO FRONT A/V

INPUT JACKS . . . . . . . . . . . . . . . .13

C CHANGING THE DVD SET UP

C TIMER RECORDING . . . . . . . . . . .30

ITEMS . . . . . . . . . . . . . . . . . . . . . . .42

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS (for DVD) . . .13

AUTOMATIC

TIMER RECORDING . . . . . . . . . .30

CUSTOM MENU . . . . . . . . . . . . . .42

LANGUAGE SETTING . . . . . . .42

DISPLAY SETTING . . . . . . . . . .43

AUDIO SETTING . . . . . . . . . . .43

PARENTAL CONTROL . . . . . . .44

OTHER SETTINGS . . . . . . . . . .44

INITIALIZE . . . . . . . . . . . . . . . . . .44

AUTO RETURN . . . . . . . . . . . . . . .32

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

C ON SCREEN DISPLAY . . . . . . . . .33

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .33

TV/VCR SECTION

C TV OPERATION AND SETTINGS .15

WATCHING A TV PROGRAM . . .15

DEGAUSSING . . . . . . . . . . . . . . . .15

PICTURE CONTROL . . . . . . . . . . .15

SLEEP TIMER . . . . . . . . . . . . . . . .16

CLOSED CAPTION SYSTEM . . . .16

CHANNEL SET UP . . . . . . . . . . . .17

DVD SECTION

C TROUBLESHOOTING GUIDE . . .45

C ABOUT THE DISCS . . . . . . . . . . . .34

PLAYABLE DISCS . . . . . . . . . . . .34

UNPLAYABLE DISCS . . . . . . . . . .34

C MAINTENANCE . . . . . . . . . . . . . . .48

DISC HANDLING . . . . . . . . . . . . .48

C SPECIFICATIONS . . . . . . . . . . . . .49

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .50

C WARRANTY . . . . . . . . . . .Back Cover

C PLAYING A DISC . . . . . . . . . . . . . .35

BASIC PLAYBACK . . . . . . . . . . . .35

GENERAL FEATURES . . . . . . . . .35

DISC MENU . . . . . . . . . . . . . . . . .35

TITLE MENU . . . . . . . . . . . . . . . . .35

RESUME . . . . . . . . . . . . . . . . . . . .36

PAUSE . . . . . . . . . . . . . . . . . . . . . .36

STEP BY STEP PLAYBACK . . . . .36

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . . . . .18

DAYLIGHT-SAVING TIME . . . . . .19

V-CHIP SET UP . . . . . . . . . . . . . . .20

TV RATING SET UP . . . . . . . . .20

MPAA RATING SET UP . . . . . .21

CHANGE ACCESS CODE . . . . .21

MENU LANGUAGE . . . . . . . . . . .21

FAST FORWARD /

FAST REVERSE . . . . . . . . . . . . . .36

SLOW FORWARD /

C VIDEO CASSETTE . . . . . . . . . . . . .22

SLOW REVERSE . . . . . . . . . . . . . .36

C PLAYBACK . . . . . . . . . . . . . . . . . . .23

NORMAL PLAYBACK . . . . . . . . .23

TRACKING ADJUSTMENT . . . . .23

SLOW MOTION . . . . . . . . . . . . . .23

STILL PICTURE . . . . . . . . . . . . . .23

VERTICAL HOLD CONTROL . . .23

ZOOM . . . . . . . . . . . . . . . . . . . . . .36

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

TV/VCR Mode

¡Rotary 4-head Record/Playback System

¡Three different playback tape speeds : SP/LP/SLP

Four heads ensure excellent picture quality and

special effects playback.

¡Two different recording tape speeds : SP/SLP

¡Auto Head Cleaner

Automatically cleans video heads as you insert or

remove a cassette.

¡Index Search

Fast-forwards to start of next recording.

¡Slow Motion

¡Zero Return

View recorded program at slower than normal

speed.

The tape returns to counter of 0:00:00 by rewinding

or fast forwarding.

¡Infrared remote control

¡Still

“Freeze” the picture at any time, for close viewing

of a particular scene.

¡Trilingual on screen TV/VCR setup display selec-

table in English, Spanish or French

¡Real time counter

¡Digital Auto Tracking (DTR)

Automatically adjusts the tracking for each tape

you play.

This shows the elapsed recording or playback time

in hours, minutes and seconds. The “–” indication

will appear when the tape is rewound further than

the tape counter position “0:00:00”.

¡Rental play mode

Improves playback picture quality from worn tapes,

such as rental tapes.

¡181 channel capability PLL frequency synthesiz-

er tuner with direct station call

(A converter may be necessary to view scrambled

cable channels.)

¡Auto repeat

Allows you to repeat the playing of a tape indefi-

nitely without pressing [PLAY O].

¡Auto Clock Setting

Allows you to set the clock function from a PBS

broadcast station.

¡Time search

Lets you set the unit to advance the tape by entering

the desired playback time you want to skip.

¡Closed Caption Decoder

¡OTR (One Touch Recording)

Instant timed recording from 30 to 480 minutes is

possible by pressing [I REC/OTR].

You may view specially labeled (cc) TV programs,

movies, news, prerecorded tapes, etc. with either a

dialogue caption or text display added to the pro-

gram.

¡1 Year, 8 events (including Daily and Weekly)

Timer Recording

¡Auto power on and off system

The built-in timer allows you to record up to 8 pro-

grams at different times on different channels up to

1 year in advance. The Daily timer allows record-

ings to be made of daily broadcasts and the Weekly

timer allows recording to be made once a week up

to the end of the tape.

Automatically turns on the unit when you insert the

cassette, turns off after auto-rewind and ejects

when the beginning of the tape is reached.

¡Auto rewind when the end of a tape is reached

(This function doesn’t occur when using timer

recording.)

¡Auto return

After timer recording is finished, the unit can

return to the beginning of the recording.

¡Smooth mode change

TV/VCR mode and DVD mode automatically

changes without control.

¡Sleep timer

Allows you to have the unit automatically turn off

at a desired time.

¡2 step picture search operation

You can view a video program at a high speed or

super high speed in either a forward or reverse

direction in LP and SLP mode. For SP mode, only

high speed is available.

¡Timer Program Extension

Allows you to shift the time schedule for automatic

timer recording.

¡V-CHIP

Enables parents to prevent their children from

watching inappropriate material on TV.

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

¡Dolby Digital sound

¡On-screen display

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Still/fast/slow/step playback

¡Search

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

Chapter search / Title search / Track search / Time

¡Repeat

Chapter / Title / Track / All / A-B

¡Random playback for Audio CD

This unit can shuffle the order of tracks to play them

in random order.

¡Zoom

Magnified screen can be displayed.

¡Program playback for Audio CD

You can program the order of tracks to play them in

any desired order.

¡Marker

The part designated by user can be called back.

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Screen saver/Auto power-off functions

¡Virtual Surround

The screen saver program starts when there is no

input from the unit for 5 minutes in the stop mode.

After the screen saver program is activated for 15

minutes, the power automatically turns off.

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available

on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD or Audio CD.

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL - [Fig.1]

DVD buttons

TV/VCR buttons

3 4

7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21

5.C STOP Button [TV/VCR P.23 / DVD P.35]

(Front panel) Stops operation of the disc.

(Remote control) Stops operation of the disc or

tape contents.

[Fig. 2]

- REMOTE CONTROL -

6.A OPEN/CLOSE Button [DVD P.35]

Press to insert a disc into or remove it from the

tray.

7.Disc loading tray

8.DVD Indicator

Lights up during DVD mode.

POWER PICTURE SLEEP SELECT

CH.

PAUSE

+100

VOL.

9.SELECT Button [TV/VCR P.15] [DVD P.35]

+10

Press to change to TV/VCR mode, external input

mode or DVD mode. You can see the mode

(TV/VCR or DVD) on the front panel indicator.

SPEED C.RESET

ZOOM

MUTE

PLAY

STOP

3 (DVD)

(DVD) 3

^(TV/VCR)4¹⁴

10.TV/VCR Indicator

15 (TV/VCR)

Lights up during TV/VCR mode.

DISC

RECORD

11. CHANNEL (CH.)

Buttons

Press to select memorized channels.

DISPLAY

SETUP

ENTER

12. Recording Indicator

TITLE

RETURN

Flashes during recording. Lights up in the Stand-

by mode for Timer Recording.

CLEAR SEARCH MODE REPEAT

A-B

13. I REC/OTR Button (Front Panel) [TV/VCR P.29]

Press to start manual recording. Press repeatedly

to start One Touch Recording.

AUDIO SUBTITLE ANGLE

MODE

RECORD Button (Remote Control) [TV/VCR P.28]

Press to start manual recording.

14. E REW Button (for TV/VCR) [TV/VCR P.25]

Press to rewind the tape or to view the picture

rapidly in reverse during playback mode. (Rewind

Search)

15. F.FWD D Button (for TV/VCR) [TV/VCR P.25]

Press to rapidly advance the tape or to view the

picture rapidly in forward during playback mode.

(Forward Search)

1.POWER Button [TV/VCR P.15 / DVD P.35]

Press to turn the power on and off.

2.VOLUME (VOL.)

Buttons

Press to control the volume level for the DVD and TV.

3.SKIP H / G Buttons (for DVD) [DVD P.37]

Press once to skip chapters or tracks to a desired

point.

SEARCH E / D Buttons (for DVD) [DVD P.36]

Press and hold to change forward or reverse play-

back speed.

16.

A STOP/EJECT Button [TV/VCR P.22, 25]

Press to stop the tape motion. Press in the stop

mode to remove tape from the unit.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

4.B PLAY Button [TV/VCR P.23 / DVD P.35]

Starts playback of the disc or tape contents.

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

- REAR PANEL - [Fig.3]

AUDIO OUT

COAXIAL

ANT.

19. VIDEO input Jack

30. CLEAR Button [DVD P.37]

Connect to the video output jack of a video camera

or VCR.

Press to clear or cancel a setting currently entered.

31. MODE Button [DVD P.38]

20. AUDIO L/R input Jacks

Connect to the audio output jacks of a video cam-

era or VCR.

Press to call up the program screen or the random

screen in the stop mode.

Press to call up the Black Level Setting screen or

the Virtual Surround screen during playback.

21. Cassette compartment

32. SEARCH MODE Button [DVD P.37]

22. PICTURE Button

Press to locate a desired point.

Press to adjust the picture.

33. AUDIO Button [DVD P.39]

Press to select a desired audio language or sound

mode.

23. Number Buttons

TV/VCR Mode: [P.17]

Press two digits to directly access the desired

channel.

Remember to press [0] before a single digit channel.

+100 Button–

Press to select cable channels which are higher

than 99.

34. SUBTITLE Button [DVD P.39]

Press to select a desired subtitle language.

35. REPEAT Button [DVD P.38]

Repeats playback of the current disc, title, chapter,

or track.

DVD Mode: [P.37]

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are higher

than 9.

36. ANGLE Button [DVD P.40]

Press to change the camera angle to see the

sequence being played back from a different angle

(if available).

37. A-B Button [DVD P.38]

24. PAUSE F Button [TV/VCR P.23 / DVD P.36]

Repeats playback of a selected section.

Pauses the current disc or tape operation.

38. RETURN Button [TV/VCR P.31] [DVD P.37]

25. SPEED Button [TV/VCR P.28]

Press to choose the desired recording speed:

SP/SLP.

Returns to the previous screen in the setup menu.

39. ENTER Button [TV/VCR P.16] [DVD P.35]

Press to accept a setting.

26. C.RESET Button [TV/VCR P.25]

Press to reset counter to “0:00:00”.

Press to cancel a setting of timer program.

(Refer to page 31.)

{

40.

Buttons

TV/VCR Mode: [P.15]

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode: [P.35]

27. DISPLAY Button

TV/VCR Mode: [P.33]

Displays the counter or the current channel num-

ber and current time on the TV screen.

DVD Mode: [P.41]

Press to select a menu item.

41. DISC MENU Button [DVD P.35]

Calls up the DVD menu.

Displays the current status on the TV screen.

42. ZOOM Button [DVD P.36]

28. SETUP Button [TV/VCR P.16] [DVD P.42-44]

Press to enter or exit the setup menu of TV or

DVD.

Enlarges part of a DVD-reproduced image.

43. MUTE Button [TV/VCR P.15]

Mutes the sound. Press it again to restore sound.

29. TITLE Button [DVD P.35]

44. SLEEP Button [TV/VCR P.16]

Displays the title menu.

Sets the Sleep Timer.

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

45. ANT(ENNA). Jack [P.12]

Connect to an antenna, cable system or satellite

system.

47. AUDIO OUT COAXIAL Jack [P.13]

Connect to the digital input of an external

amplifier or decoder (for DVD Audio only).

46. Power cord [P.15]

Connect to a standard AC outlet (120V/60Hz).

NOTE:

Remove the power cord from the hook to

avoid breaking a wire before you connect to a

standard AC outlet.

•

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

[BATTERY PRECAUTIONS]

Be sure to follow the correct polarity as indicated

in the battery compartment. Reversed batteries

may cause damage to the device.

•

Do not mix different types of batteries together

(e.g. Alkaline and Carbon-Zinc) or old batteries

with fresh ones.

•

3)Replace the cover.

If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture.

•

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

Plug the incoming cable into the ANT. jack on the rear of the unit.

If your cable service supplies you with a converter box or if you use a

satellite system, connect the box with this unit as shown below.

Cable

TV signal

Antenna

Incoming cable from home Antenna /

Cable Company (No Cable Box)

AUDIO OUT

COAXIAL

ANT.

Rear of the unit

ANT.

Cable Box or

Satellite Box*

OUT

[Fig. 4]

Incoming cable from Cable Company

or Satellite Antenna

*NOTE (DO NOT DISCONNECT FROM BOX)

Some cable TV systems use scrambled signals and

require a special converter to receive these channels.

Consult your local cable company.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry as practical.

Bent pin

NOTE:

Before plugging the antenna into the ANT. jack of the unit, check that the pin is

not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the

ANT. jack of the unit.

•

Cable

Plug

(Needs to be

straightened)

(Straight pin)

NOTE:

For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack

before moving the unit.

•

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO FRONT A/V INPUT JACKS

When you watch a program recorded on another source (VCR or video camera), use the

Audio/Video input jacks on the front of the unit.

AUX

Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO

jacks of this unit.

Then press [SELECT] or [CH.

] until “AUX” appears on the screen.

DVD buttons

TV/VCR buttons

ex.

VCR or video camera, etc.

To the Audio output jacks

(IN)

Audio cable

(commercially available)

HEADPHONE VIDEO

AUDIO

(OUT)

To the Video output jack

[Front of the unit]

Video cable

(commercially available)

(IN)

[Fig. 5]

NOTE:

When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the

monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R

channel equally.

•

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS (for DVD)

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

AUDIO OUT

COAXIAL

NNTT..

(OUT)

ex.

MD deck, DAT deck, etc.

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

To Coaxial digital

Audio input jack

Audio coaxial digital cable

(commercially available)

(IN)

[Fig. 6]

NOTES:

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-

tings may generate noise distortion and may also damage the speakers. (Refer to page 43.)

•

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its AUDIO OUT COAXIAL jack. By hooking the unit up to a Dolby

Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround

sound as enjoyed in movie theaters.

Use audio coaxial digital cables (commercially available) for the audio connections.

Center

speaker

AUDIO OUT

COAXIAL

ANT.

(OUT)

Front speaker

(left)

Front speaker

(right)

To AUDIO OUT

COAXIAL jack

(Only DVD AUDIO OUT)

Dolby Digital

decoder

To Coaxial digital

Audio input jack

(IN)

Audio coaxial digital cable

(commercially available)

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 7]

NOTES:

Be sure to turn off the power to all components in the system before connecting another component.

Refer to the Owner’s Manuals for the components to be connected to the unit.

If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the

setup mode. (Refer to page 43.)

•

Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the

setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the

speakers. (Refer to page 43.)

•

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TV/VCR SECTION

TV OPERATION AND SETTINGS

WATCHING A TV PROGRAM

DEGAUSSING

TV/VCR

This television has a degaussing circuit that will clear

up color errors on the TV screen that are caused by

any excess magnetism which happens to get too close

to the TV. This circuit is designed to operate once

when the set is first plugged in. If minor color

errors are seen in some locations on the screen,

please unplug the TV for approximately 30 min-

utes. When the TV is plugged back in, the degauss-

ing circuit will operate once to clear them up. Repeat

this procedure any time the TV screen is accidentally

magnetized or when the TV is moved or relocated.

TV/VCR

1 Plug in the unit power cord

Plug the unit power cord into a standard

AC outlet.

NOTE:

If any digits appear in the corner of the

•

screen, press [POWER] without

unplugging the power cord.

2 Turn on the unit

Press [POWER] to turn on the unit.

PICTURE CONTROL

TV/VCR

3 Select the channel number

Press [CH.

] or the Number buttons to select

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

your desired channel number.

Notes for using the Number buttons:

¡You must precede single-digit channel numbers

with a zero (for example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, press [+100] first, then press the last two

digits. (Example: to select channel 125, first press

[+100] then press [2] and [5].)

Make sure ...

The unit must be turned on.

•

1 Call up the menu

4 Adjust sound

Press [PICTURE].

Press [VOL.

] to adjust the

volume.

2 Select item you want to adjust

Press [K / L] until desired control is displayed.

VOLUME 20

Press [MUTE] to instantly mute

the sound.

Press it again to restore the previous sound level.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

NOTE:

If you press [CH.

can change the TV channels. Even if you turn off

the unit in the DVD mode, when you turn it on

again, it will go into the TV/VCR mode.

BRIGHT

] in the DVD mode, you

•

–

P +

3 Adjust the setting

Press

seconds.

[

to adjust to your desired level within 5

TO WATCH CABLE OR SATELLITE

CHANNEL

If the unit is connected to a cable box or satellite

box, press [CH.

according to the output channel setting of the

device, and select desired channel on that device.

to decrease

brightness

to decrease

contrast

•

BRIGHT

to increase

brightness

to increase

contrast

] to select CH3 or CH4

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

TO WATCH EXTERNAL INPUT

to purple

to green

to clear

When an external equipment is connected to the

•

front AUDIO/VIDEO input jacks, press

[SELECT] or [CH.

] repeatedly until

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

“AUX” appears on the screen.

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback of poorly recorded or worn VCR tapes.

If the unit displays a black box

on the TV screen, this means that

the unit is set to the TEXT mode.

To clear screen, select [CAP-

•

SLEEP TIMER

TV/VCR

The Sleep Timer function turns off the unit without

using [POWER] after a desired period of time.

NOTE:

TION1], [CAPTION2] or [OFF].

Make sure ...

The unit must be turned on.

This function does not work during Recording

•

mode.

1 Select “CAPTION”

1 Call up the Sleep Timer Setting

- TV/VCR SETUP -

Press [SETUP].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press [SLEEP] so that “SLEEP 0 MINUTE” appears.

Press [K / L] to point to

“CAPTION”.

2 Set sleep time

TIME SEARCH

INDEX SEARCH

Press [SLEEP] repeatedly until

your desired sleep time appears.

Each additional press will increase

the time by 30 minutes up to 120

minutes.

After 5 seconds, the Sleep Timer setting will disap-

pear automatically.

2 Select your desired caption mode

Press [ENTER] repeatedly until

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

SLEEP 120 MINUTE

your desired caption menu

appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

TO CANCEL THE SLEEP TIMER

3 Exit the caption setting mode

Press [SLEEP] to call up the Sleep Timer Setting.

Press [SLEEP] repeatedly until “SLEEP 0 MINUTE”

appears.

Press [SETUP] to exit the menu.

NOTE:

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

•

CLOSED CAPTION SYSTEM

TV/VCR

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Then press [SETUP] to return to TV

mode.

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: You can watch dramas, movies and

news while captioning the dialogues and the contents

of news.

TEXT mode: You can watch half screen text informa-

tion if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is

usually used for a second language if available.

NOTES:

Not all programs are broadcast with closed cap-

•

tions. Your unit is designed to provide error free

closed captions from high quality antenna, cable

and VCR signals. Conversely, poor quality signals

are likely to result in caption errors or no captions

at all. Common signal conditions which may cause

caption errors are listed below:

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDING/DELETING CHANNELS

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

CHANNEL SET UP

TV/VCR

Make sure ...

The unit must be turned on.

•

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

1 Select “CHANNEL SET UP”

AUTO CHANNEL PROGRAMMING

Press [SETUP].

Press [K / L] to point to

“CHANNEL SET UP”, then press

[ENTER].

As the initial setting, this unit has memorized all

channels, including the ones not available in your

area. This feature automatically puts only available

channels into the memory.

TIME SEARCH

INDEX SEARCH

– CHANNEL SET UP –

2 Select “ADD/DELETE CH”

Press [K / L] to point to

“ADD/DELETE CH”, then press

[ENTER].

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

1 Select “CHANNEL SET UP”

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

Press [SETUP].

Press [K / L] to point to

“CHANNEL SET UP”, then press

[ENTER].

TIME SEARCH

INDEX SEARCH

3 Enter the desired channel number

2 Begin channel scanning

Press [K / L] to point to

Press [CH.

] or the Number

– CHANNEL SET UP –

buttons until your desired channel

number appears. (You can also

press [K / L] to enter it.)

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

“AUTO CH PROGRAMMING”,

then press [ENTER].

ADD / DELETE

The tuner scans and memorizes all

the active channels in your area.

You must precede single-digit

•

channel numbers with a zero

(Example: 02 ... 09).

(Example: CH8)

When selecting cable channels which are higher

than 99, press [+100] first, then press the last two

digits. (Example: to select channel 125, first press

[+100] then press [2] and [5].)

3 After scanning

•

The tuner stops on the lowest memorized channel.

NOTES:

When “AUTO CH PROGRAM-

MING” is activated where there

is no TV signal input, “NO TV

SIGNALS” will appear on the

display after the completion of

channel scanning.

•

NO TV SIGNALS

4 Delete (or add) it from (or into) memory

Press [ENTER]. The channel number changes to

light red. The channel is deleted from memory.

To delete another channel, repeat steps 3 to 4.

If you press [ENTER] again, the channel is memo-

rized again.

•

The unit may recognize CATV channels to be TV

•

channels if reception condition is poor. In this case,

check the antenna connection and try “AUTO CH

PROGRAMMING” again when reception condi-

tions are better.

Added channel : Light blue

Deleted channel : Light red

Channel memory programming is NOT neces-

•

sary when connected to a cable box or satellite

box. Just select the channel for cable box or

satellite input (ex. CH3) on the unit, then select

your desired channel on the cable box or satel-

lite box.

5 Exit the channel setup mode

Press [SETUP] to exit the menu.

NOTE:

To confirm that channel(s) has been deleted or

•

added, press [CH.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CLOCK SET UP

5 Select the year

Press [K / L] until your desired

year appears.

(Example: “2005”)

Then press [B].

(AUTO / MANUAL)

– MANUAL CLOCK SET –

MONTH DAY

YEAR

2 0 0 5

TV/VCR

0 5

0 6 FRI

The unit clock must be set correctly so that VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the unit,

then set to [ON] the auto clock setting which will

periodically correct the setting if necessary.

NOTE:

If you cannot receive a station with time signals,

auto clock setting cannot be performed. Use manu-

al setting only.

HOUR

– –

MINUTE

– – – –

6 Select the hour

Press [K / L] until your desired

hour appears.

(Example: “5”, “PM”)

Then press [B].

– MANUAL CLOCK SET –

MONTH DAY

YEAR

2 0 0 5

•

0 5

0 6 FRI

HOUR

0 5

MINUTE

– – PM

MANUAL CLOCK SETTING

Make sure ...

7 Select the minute

Press [K / L] until the

desired minute appears.

(Example: “40”)

– MANUAL CLOCK SET –

MONTH DAY YEAR

The unit must be turned on.

In the example below, the clock is to be set to:

•

0 5

0 6 FRI

2 0 0 5

DATE

SETTING TIME

May 6th, 2005

5:40PM

HOUR

0 5

MINUTE

4 0 PM

1 Select “SETTING CLOCK”

Press [SETUP].

Press [K / L] to point to

“SETTING CLOCK”, then press

[ENTER].

8 Start the clock

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

5:40 PM

Press [SETUP].

Although seconds are not displayed,

they begin counting from 00 when

you press [SETUP]. Use this fea-

ture to synchronize the clock with

the correct time.

TIME SEARCH

INDEX SEARCH

2 Select “MANUAL CLOCK SET”

Press [K / L] to point to

“MANUAL CLOCK SET”, then

press [ENTER].

NOTE:

– SETTING CLOCK –

AUTO CLOCK

[ON]

When unplugging the AC cord or if there is a

power failure for more than 3 seconds, you may

have to reset the clock.

•

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow steps 1 to 2.

2)Select the item you want to change using [B] .

3)Enter correct numbers using [K / L].

4)Press [SETUP] to start the clock.

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press [ENTER] to turn [OFF] this function before

this step.

•

3 Select the month

Press [K / L] until your desired

month appears.

– MANUAL CLOCK SET –

MONTH DAY

YEAR

0 5

– – – – – – – – –

(Example: May → “05”)

Then press [B]. (Or press [s] to

go back one step.)

HOUR

– –

MINUTE

– – – –

4 Select the day

Press [K / L] until your desired

day appears.

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 – – – – – – –

(Example: 6th → “06”)

Then press [B].

HOUR

– –

MINUTE

– – – –

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTOMATIC CLOCK SETTING

Make sure ...

4 Enter the channel number that contains the

The unit must be turned on.

Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable

•

Automatic Clock Setting Signal

– SETTING CLOCK –

Press [RETURN] to go back to

AUTO CLOCK

[ON]

“SETTING CLOCK” menu.

Press [L] to select

AUTO CLOCK CH SEARCH

system connection using the ANT. jack on the rear

of the unit.

NOTES:

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

“AUTO CLOCK CH”.

[OFF]

If a cable converter box is being used, make sure it

is powered on.

You must use the remote control to perform the

clock setting procedure.

•

Press [s / B] until you locate Auto Clock Set station

number.

•

5 Exit the setting clock mode

Press [SETUP] to exit the menu.

If the unit is connected directly to a cable converter

•

box or satellite box, the local PBS station must be

selected on the cable box itself and the unit must be

set to the output channel of the cable converter box

or satellite box (usually channel 3 or 4), to be able

to set up or correct the clock automatically.

NOTE:

Once the unit is turned off, it will periodically

check and set the correct date and time.

•

DAYLIGHT-SAVING TIME

1 Select “SETTING CLOCK”

- TV/VCR SETUP -

TIMER PROGRAMMING

TV/VCR

Select this feature and the unit’s clock automatically

will advance one hour in April, then reverse one hour

in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

Press [SETUP].

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press [K / L] to select

“SETTING CLOCK”, then press

[ENTER] .

TIME SEARCH

INDEX SEARCH

First Sunday of April : At 2 AM the clock immedi-

•

2 Set “AUTO CLOCK” to [ON]

Press [ENTER] to select [ON].

– SETTING CLOCK –

ately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM will

not record.

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

•

[OFF]

Make sure ...

3 Begin “AUTO CLOCK CH SEARCH”

The unit must be turned on.

•

Press [L] to select “AUTO CLOCK

CH SEARCH”.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

1 Select “SETTING CLOCK”

Press [SETUP].

Press [K / L] to point to

“SETTING CLOCK”, then press

[ENTER].

Then press [ENTER].

- TV/VCR SETUP -

TIMER PROGRAMMING

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

The unit begins searching for the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

•

[OFF]

station which contains the auto

clock set signal. The search for a

TIME SEARCH

INDEX SEARCH

signal may take up to 20 seconds per channel.

When the search has ended, “_ _”

– AUTO CLOCK CH SEARCH –

•

appears at the lower left of the

screen.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press [K / L] to point to “D.S.T.”,

then press [ENTER] until [ON]

appears.

– SETTING CLOCK –

Write down the number(s) that

appear on the screen. They are the

auto clock station(s) in your area.

AUTO CLOCK

[ON]

_ _

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 18.

3 Exit the Daylight-Saving Time mode

Press [SETUP] to exit the menu.

NOTE:

During AUTO CLOCK CH SEARCH, the picture

may be distorted.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps 1 to 2 and select [OFF] using [ENTER].

•

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

V-CHIP SET UP

When you select a rating and set

•

it to [BLOCK], the higher ratings

will be blocked automatically.

The lower ratings will be avail-

able for viewing.

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA( LSV)

[VIEW]

[BLOCK]

TV/VCR

(

)

This feature enables parents to prevent their children

from watching inappropriate material on TV. When

you try to access a program which is blocked,

“PROTECTED PROGRAM by ...” message appears

on the TV screen.

When you set the lowest rating to

[VIEW], all other ratings will automatically be

available for viewing.

•

V-CHIP SET UP

5 Setting “Sub-Ratings”

Make sure ...

TV–Y

[VIEW]

When you select the ratings of TV-

TV–Y7

TV–G

(

)

The unit must be turned on.

•

Y7, TV-PG, TV-14 or TV-MA you

will have the option of setting sub

rating categories.

Press [K / L] to select a rating with

sub-ratings you wish to block, then

press [ENTER] twice.

Press [K / L] to select a sub-rating,

then press [ENTER] to set it to

[BLOCK] or [VIEW].

TV–PG (

)

TV–14

(

TV–MA(

1 Select “V-CHIP SET UP”

Press [SETUP].

Press [K / L] to select “V-CHIP

SET UP”, then press [ENTER].

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

TV–Y7

[BLOCK]

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2 Enter Access code

Press the Number buttons to

enter the access code.

TV–PG

[BLOCK]

ACCESS CODE

For the first time set-up or in the

event the unit has lost power,

enter the default code of 0000.

•

Selection

TV-Y7

Rating Category Explanations

Fantasy Violence

3 Select the desired item

TV-PG, TV-14, TV-MA

Press [K / L] to select “TV RATING”, “MPAA RAT-

ING” or “CHANGE CODE”, then press [ENTER].

Refer to the pages below to set up each item.

– V-CHIP SET UP –

Suggestive Dialog (TV-PG, TV-14 only)

Coarse Language

Sexual Situation

Violence

P 20 Step

P 21 Step

B TV RATING

MPAA RATING

CHANGE CODE

NOTE:

The blocked sub-ratings will

appear next to the rating category

in the “TV RATING” menu.

P 21 Step

•

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK]

TV RATING SET UP

Follow steps to in the “V-CHIP SET UP” sec-

tion above.

6 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

4 Blocking TV programs

Press [K / L] to select a rating that

you wish to block.

Press [ENTER] repeatedly to set it

to [BLOCK] or [VIEW].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

NOTE:

(

)

To change the rating, the TV must

•

(

PROTECTED PROGRAM

by TV-Y

be turned to an unprotected pro-

gram. If “PROTECTED PRO-

GRAM by ...” appears on the

screen, please change the channel

to a station that is not protected.

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7

TV-G

Appropriate for children seven and older

General Audience

TV-PG

TV-14

Parental Guidance suggested

Unsuitable for children under 14

TV-MA Mature audience only

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU LANGUAGE

MPAA RATING SET UP

TV/VCR

Follow steps to in the “V-CHIP SET UP” section

on page 20.

1 Select “LANGUAGE”

Press [SETUP].

Press [K / L] to point to

“LANGUAGE”.

- TV/VCR SETUP -

4 Select your desired item

Press [K / L] to point to your

desired item, then press [ENTER]

to select [BLOCK] or [VIEW].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

TIME SEARCH

INDEX SEARCH

Selection

PG-13

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Press [ENTER] repeatedly to select “ENGLISH”,

“ESPAÑOL”= Spanish or “FRANÇAIS”= French.

3 Exit the Language mode

Press [SETUP] to exit the menu.

NOTES:

NC-17

Mature audience only

This function effects only the language on the

screen menu and not the audio source.

•

When you select a rating and set it to [BLOCK],

the higher ratings will be blocked automatically.

The lower ratings will be available for viewing.

When you set the lowest rating to [VIEW], all

other ratings will automatically be available for

viewing.

•

If for some reason the menu is in Spanish or

•

French, press [SETUP], press [K / L] to point to

“IDIOMA [ESPAÑOL]” or “LANGAGE

[FRANÇAIS]”, then press [ENTER] repeatedly to

select desired language, then press [SETUP].

5 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

CHANGE ACCESS CODE

Follow steps to in the “V-CHIP SET UP” sec-

tion on page 20.

4 Enter New code

NEW CODE

X X X X

Press the Number buttons to enter

your desired access code in the

“NEW CODE” space, then enter

the same code in the “CONFIRM

CONFIRM CODE

CODE” space. When completed, the menu will

return to “V-CHIP SET UP”.

Make sure you enter exactly the same new code in

the “CONFIRM CODE” space as one in the

“NEW CODE” space. If they are different, the

“NEW CODE” space is cleared for redoing.

•

5 Exit the V-Chip setting mode

Press [SETUP] to exit the menu.

NOTE:

Your personal access code will be erased and will

•

return to the default (0000) when a power failure

occurs or when you turn off the power using a

wall switch. If you have forgotten the code, unplug

the power cord for 10 seconds to restore the access

code to 0000.

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO CASSETTE

This unit will operate with any cassette that has the

mark. For best results, we recommend the use of

high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the unit. The unit will

automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or vice versa. Before using a tape with

these conditions, to avoid damage of the tape and

your unit, wait until the tape has warmed to room

temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

Window

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

1)In the stop mode, press [C A STOP/EJECT] on

the unit. The cassette will be ejected.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

ERASE PREVENTION

NOTE:

You can play back a tape recorded in LP mode

(Long Play).

•

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Plastic Tape

NOTE:

In DVD mode, whether the cassette is with tab or

without tab you insert, it doesn’t start playing until

•

[B PLAY]

you press

In TV/VCR mode, if the cassette without tab is

inserted, playback will automatically start.

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYBACK

NORMAL PLAYBACK

SLOW MOTION

TV/VCR

Press [PAUSE F], then press [D] to start the play-

back in slow motion. The unit mutes the sound dur-

ing slow motion. Press [PLAY O] to return to nor-

mal playback.

Make sure ...

The unit must be turned on.

•

1 Insert a prerecorded tape

If the erase-prevention tab has been removed, the

unit will start playback automatically.

NOTE:

If it is left in the Slow mode for more than 5 min-

utes, the unit will automatically go into the stop

mode.

•

PLAY

2 To begin playback

Press [PLAY O].

STILL PICTURE

TV/VCR

You can view a still picture on the TV screen during

playback (the Still mode). Press [PAUSE F] during

playback. Only tapes recorded in the SLP mode will

show the least amount of lines. Press [PLAY O] to

return to playback.

3 To stop playback

Press [STOP C].

STOP

NOTES:

You can advance the picture one frame at a time by

pressing [PAUSE F] during the Still mode.

If it is left in the Pause mode for more than 5 min-

utes, the unit will automatically switch to the stop

mode.

•

NOTES:

•

Even in the DVD mode, you can start the VCR

playback if you press [ PLAY] (of the TV/VCR

side).

•

VCR playback will stop and the mode will change

•

to the DVD mode by pressing [SELECT],

VERTICAL HOLD CONTROL

[

PLAY] (DVD side) or [ OPEN/CLOSE].

TV/VCR

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

TRACKING ADJUSTMENT

[CH.

NOTE:

TV/VCR

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

If there are video noise lines on the screen, refer to

TRACKING ADJUSTMENT on this page.

•

Noise lines (black and white streaks) may appear

on the playback picture when playing pre-recorded

tapes or tapes recorded on other VCR. If this

occurs, press [CH.

] until the streaks disap-

pear.

You can reduce the noise lines by pressing

•

[CH.

] in Slow mode too. Tracking adjust-

ment in Slow mode will not be set automatically.

To return to the Digital Auto Tracking function,

stop the tape once and start playback.

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

The unit must be turned on.

•

Insert a prerecorded tape.

•

TV/VCR

The unit has the auto repeat function that allows you to

repeat a tape indefinitely without pressing [PLAY O].

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

RENTAL PLAYBACK

TV/VCR

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

Press [SETUP].

TIMER PROGRAMMING

CHANNEL SET UP

SETTING CLOCK

Press [SETUP].

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

CHANNEL SET UP

Press [K / L] to point to “USER’S

SET UP”, then press [ENTER].

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press [K / L] to point to “USER’S

SET UP”, then press [ENTER].

INDEX SEARCH

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press [K / L] to point to

“RENTAL”.

2 Select “ALL” or “BLANK”

Press [K / L] to point to “REPEAT

PLAY”.

Press [ENTER] repeatedly until

your desired selection [ALL] or

[BLANK] appears.

USER’S SET UP

–

RENTAL

[ON]

[OFF]

REPEAT PLAY

AUTO RETURN

RENTAL

[OFF]

[ALL]

[OFF]

REPEAT PLAY

AUTO RETURN

Press [ENTER] until [ON] appears.

3 Exit the Rental setting

Press [SETUP] to return to the TV mode.

3 Exit the Repeat Play setting

Press [SETUP] to return to the TV mode.

4 Start playback

Press [PLAY O] to start playback.

“RENTAL PLAY B” appears.

4 Start playback

Press [PLAY O] to start the Repeat Play.

“REPEAT PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the unit.

•

Once you select the Repeat Play mode, it stays in

effect even after you turn off the unit.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE RENTAL MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Press [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER]. Press [SETUP] to return to TV mode.

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Make sure ...

NOTE:

Tapes recorded in the SP or LP mode will normally

•

The unit must be turned on.

•

display a noise bar on the TV screen and the pic-

ture may revert to Black and White.

Insert a tape.

•

ZERO RETURN

3 Return to normal speed

Press [PLAY O].

TV/VCR

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

TIME SEARCH

TV/VCR

Zero Return WILL NOT work on a blank tape or

•

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

a blank portion of a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

NOTE:

•

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

In the example below: To watch a program before/

after 2 hour 50 minutes from the present position, in

either direction.

2 Reset the counter to 0:00:00

Press [C.RESET] repeatedly.

3 Begin recording or playback

Press [RECORD] or [PLAY O].

Press [STOP C] when recording or playback is com-

pleted.

- TV/VCR SETUP -

1 Select “TIME SEARCH”

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

Press [SETUP].

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

Press [K / L] to point to “TIME

SEARCH”, then press [ENTER].

4 To activate “ZERO RETURN”

Press [SETUP].

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

2 Enter your desired time

Press [K / L] until your desired time

appears. (Example: “2:50” stands for

2 hours 50 minutes)

Press [K / L] to point to “ZERO

RETURN”, then press [ENTER].

The unit will begin rewinding and

the counter will appear on the TV

screen.

TIME SEARCH

2 : 50

TIME SEARCH

INDEX SEARCH

If you wish to cancel the Time

Search at this point, press

[SETUP].

The tape will automatically stop when the counter

returns to 0:00:00 (approx.).

3 Begin Time Search

PICTURE SEARCH

By pressing [s B], the unit will rewind or fast for-

ward to the specified point.

TV/VCR

The time counts down during the search. When the

display shows “0:00”, the tape will start playback

automatically.

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

TO CANCEL DURING TIME SEARCH

Press [C A STOP/EJECT] on the unit or

[STOP C]. This will delete the selected time.

1 Start Picture Search

During playback, press [D] or [E] to view at a

high speed (in forward/reverse).

2 Change searching speed

Press [D] or [E] again to view at super high

speed (in the LP/SLP modes only).

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

- TV/VCR SETUP -

INDEX SEARCH

1 Select “INDEX SEARCH”

Press [SETUP].

Press [K / L] to point to “INDEX

SEARCH”, then press [ENTER].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TV/VCR

This feature provides a method of indexing the start-

ing point so that it can be easily returned to in either

fast forward or rewind mode.

TIME SEARCH

INDEX SEARCH

The index mark will be made automatically when

[RECORD] is pressed. It will also be marked at

the starting point of Timer recording and OTR.

The index mark will not be recorded if [PAUSE

F] is pressed and released during recording.

The time gap between making the index marks on

the tape should be greater than 1 minute for SP

recording, 2 minutes for LP recording and 3 min-

utes for SLP recording.

•

2 Enter your desired number

Press [K / L] until the number of

programs that you want to skip

appears.

INDEX SEARCH

0 3

•

(Example: “03” for 3 programs)

•

The Index Search mode will be canceled if the pro-

cedures are not activated in 30 seconds.

•

In some cases, the index mark at the beginning of

video tape cannot be detected.

Example: You are watching program number 4 and

want to fast forward to program number 7. You

must skip three programs.

•

3 Begin Index Search

Press [s B]. The unit begins rewinding or fast for-

warding to the beginning of desired program.

NOTE:

Every time an index signal is skipped, the number

in the program indicator decreases by one.

•

CURRENT PLAYBACK PROGRAM

Beginning of

the tape

End of

the tape

4 After Index Search

When the preset program is reached, the unit will

start playback automatically.

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5 Pro.6 Pro.7

A video cassette must be inserted in the unit for

this function to work.

•

INDEX MARK

The number of Index Searches can be set up to 20.

This function will not operate in the Recording

mode.

•

When you want to cancel the Index Search while

in progress, press [STOP C].

•

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

TV/VCR

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the unit will eject the tape and turn itself

off.

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.) The “–” indication will appear when the tape has

rewound further than “0:00:00” on the tape counter.

•

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Make sure ...

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTES:

This unit will ONLY record and view the same channel.

This unit cannot record the contents from the built-in DVD.

•

SKIPPING UNWANTED

NORMAL RECORDING

SCENES DURING RECORDING

TV/VCR

You can ONLY watch the same TV program that is

being recorded.

Press [PAUSE F] to temporarily

stop recording.

PAUSE

Press [PAUSE F] or [RECORD]

to resume recording.

NOTES:

1 Select the channel to be recorded

Press the Number buttons or

CH 10

[CH.

After 5 minutes, the unit will

automatically switch to the Recording mode to pre-

vent tape damage.

•

NOTE:

If Closed Caption mode is on, the On-Screen

Display will appear for 5 seconds, then disappear.

•

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded must be selected on the

cable box or satellite box.

•

2 Select the tape speed

Press [SPEED] to select the desired

tape speed (SP/ SLP).

REC

3 Begin recording

Press [RECORD].

4 Stop recording

Press [STOP C].

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Time(s)

1 time

Display

Recording length

(normal recording)

OTR (One Touch Recording)

2 times

3 times

0:30

1:00

30 minutes

60 minutes

TV/VCR

This function enables you to set a recording length

simply by pressing [ REC/OTR] on the unit.

17 times

8:00

480 minutes

Make sure ...

The unit must be turned on.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

tape to the point at which you want to begin

recording.)

NOTES:

TV/VCR

You can make copies of video tapes made by friends

or relatives for your enjoyment.

You can not copy a DVD to a videotape.

You cannot start OTR with the remote control.

•

Recording starts immediately when [ REC/OTR]

is pressed.

When [REC/OTR] is pressed 18 times, the unit

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

returns to the Normal Recording mode.

To stop the OTR operation, press [C STOP] on

the unit or on the remote control.

To show the remaining time, press [DISPLAY] on

the remote control so that “OTR” appears on the

TV screen. (It will show up momentarily then dis-

appear.)

•

Connect your unit and a source (Playing) VCR using

the following diagram.

•

[This unit]

[Fig.8]

Recording stops when the display shows 0:00.

Please note that in the SLP mode maximum

recording time, assuming the tape is started at the

beginning, is 8 hours using T-160 (or 6 hours

using T-120).

•

[Ex: Source VCR or

camcorder]

If the tape runs out before the end time, the unit

will switch to the stop mode immediately, ejects

the tape and turns itself off.

Even if [POWER] is pressed during OTR, the unit

continues recording.

•

AUDIO

Audio/Video

cable

(not supplied)

•

OUT

VIDEO

OUT

1 Select the channel to be recorded

1)Insert a pre-recorded video cassette into the source

VCR or camcorder.

2)Insert a blank video cassette or one you want to

record over, into the unit’s cassette compartment.

3)Press [SPEED] on remote control for the unit to

select the desired recording speed (SP/SLP).

Press the Number buttons or [CH.

NOTE:

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

•

4)Press [CHANNEL

] on the unit until “AUX”

appears on the screen.

2 Select the tape speed

5)Press [ REC/OTR] on the unit.

Press [SPEED] to select the desired tape speed

6)Begin playback of the tape in the source VCR or

camcorder.

(SP/SLP).

NOTE:

For best results during copying, use the front

•

3 Begin OTR

panel controls whenever possible. The remote

control might affect the source VCR’s playback

operation.

OTR (2 : 30)

Press [ REC/OTR] on the unit as

many times as needed. The record-

ing length will be determined by

the number of times you press

7)To stop copying, press [C A STOP/EJECT] on

the unit, then stop the tape on the source VCR or

camcorder.

[

REC/OTR]. Each time it is

pressed, the recording time will be

increased by 30 minutes up to 8 hours.

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING

AUTOMATIC TIMER

RECORDING

1 Select “TIMER PROGRAMMING”

- TV/VCR SETUP -

Press [SETUP].

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Confirm “TIMER PROGRAM-

MING” is pointed by pressing [K],

then press [ENTER].

TV/VCR

You may set the unit to start and end a recording

while you are away. You can set 8 programs to record

on specific days, daily or weekly within a 1 year

period.

TIME SEARCH

INDEX SEARCH

If you have not yet set the clock,

•

“MANUAL CLOCK SET” appears. If so, follow

steps 3 to 8 on page 18. Then set the timer record-

ing.

In the example below, the timer is being set to record:

DATE:

July 4th, 2005

SETTING TIME: from 7:30PM to 8:50PM

2 Select your desired program position (1 to 8)

CHANNEL:

TAPE SPEED:

CH61

Press [K / L] to select the desired

– TIMER PROGRAMMING –

CH DATE

BEGIN END

program position, then press [B].

- - -/- - - - - -:- -

-:- - - -

Make sure ...

If a cable box or satellite box is connected with the

unit you will be limited to record only one channel,

and the channel selector on the unit must be select-

ed to the output channel of the boxes CH 3 or CH

4 and then the actual channel to be recorded must

be selected on the boxes.

•

3 Set the channel number

Press [K / L] until the desired

channel number appears (Example:

CH61), then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

Clock must be set to the correct time and date

before setting the timer.

•

The unit must be turned on to program it.

Insert a cassette tape with its erase-prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

NOTE:

If the unit is connected to a cable box or satellite

box, the unit must be on CH3 or CH4, then the

channel to be recorded is selected on the cable box

or satellite box.

•

The channel you want to record is properly set in

advance. (Refer to page 17.)

•

Avoid overlap of programs ...

There is a chance that a program will not be record-

ed, when programs overlap;

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press [K] until the desired date

appears.

(Example: “7/04” for July 4th)

- - -/- - - - - -:- -

61 7/04 MON -:- -

- - -/- - - - - -:- -

-:- - - -

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

Then press [B].

When the starting time is the same, the program set

on the highest position in the program list has pri-

ority.

The illustration below demonstrates the sequence

of recordings.

•

For every day recording : To record a TV program

at the same time on the same channel every day.

(Example: Monday through Sunday)

•

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

Press [L] until “EVRY DAY”

appears, then press [B].

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

Recording Sequence

For weekly recording : To record a TV program at

the same time on the same channel every week.

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

(Example: every Monday)

– TIMER PROGRAMMING –

CH DATE

BEGIN END

9:30AM-12:00PM

Press [L] until “EVRY” and

your desired day of the week

appear together, then press [B].

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

5 Set beginning hour

Press [K / L] until the desired hour

appears.

(Example: “ 7, PM” for 7:30PM)

Then press [B].

– TIMER PROGRAMMING –

CH DATE BEGIN END

The display will not be turned on automatically at

•

the time the programmed recording begins. To

watch the currently recorded TV program or to

play a DVD disc, press [POWER] and [SELECT]

to choose the TV/VCR mode or the DVD mode.

- - -/- - - - - -:- -

-:- - - -

61 7/04 MON 7:12^P

- - -/- - - - - -:- -

If the tape runs out before the end time, the unit

will switch to the stop mode immediately and the

tape will be ejected.

•

– TIMER PROGRAMMING –

CH DATE BEGIN END

6 Set beginning minute

Press [K / L] until the desired

minute appears.

- - -/- - - - - -:- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

TIMER PROGRAM EXTENSION

(Example: “30” for 7:30PM)

Then press [B].

To shift the time schedule of an automatic timer

recording.

1)Press [POWER].

2)Repeat step 1 on page 30.

3)Press [RECORD] and select the desired program

using [K / L].

4)Press [RECORD] again.

7 Set end hour

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press [K / L] until the desired hour

appears.

- - -/- - - - - -:- -

-:- - - -

8:30^PM- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

(Example: “8, PM” for 8:50PM)

Then press [B].

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press [PAUSE F] on

the remote control. The recording time returns to

the original time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press [K / L] until the desired

minute appears.

(Example: “50” for 8:50PM)

Then press [B].

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

NOTE:

9 Set the tape speed

Press [K / L] until the desired tape

speed appears. (Example: “SP”)

When you shift forward the time schedule during

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

recording, the recording speed will automatically

be set to the SLP mode.

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

61 7/04 MON 7:30^P

- - -/- - - - - -:- -

5)Press [ENTER] or [RETURN] to exit the setting

menu. Then press [SETUP] to return to original

mode.

10 Finish setting the program

TO CORRECT A PROGRAM

Press [ENTER] or [RETURN] to complete setting.

While setting a program; press [s] to go back one

step and enter the correct numbers using [K / L].

•

To set another program, repeat steps 2 to 10.

Press [SETUP] to exit the menu.

•

After setting a program;

1)Press [POWER].

•

11 Set the timer

Press [POWER] to set automatic timer recording.

The recording indicator lights up.

2)Repeat steps 1 to 2 on page 30.

3)Press [B] (or press [s] to go back one step)

until the part you want to correct begins flashing,

then make the changes using [K / L].

4)Press [POWER] to set automatic timer recording.

You must turn off the unit to activate automatic

timer recording.

•

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

If the erase-prevention tab is removed, the cassette

will be ejected when [POWER] is pressed to off.

1)Press [POWER].

•

2)If recording is in progress, press

[C A STOP/EJECT] on the unit.

3)Repeat steps 1 to 2 on page 30 and select a pro-

gram you want to cancel.

4)Press [C.RESET].

5)Press [SETUP] to return to TV mode.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TO CONFIRM THE TIMER SETTING

1)Press [POWER] so that the Recording indicator

light goes off.

AUTO RETURN

TV/VCR

2)Press [SETUP].

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

3)Confirm “TIMER PROGRAMMING” is selected.

4)Press [ENTER]. The details of programs appear on

the TV screen.

5)Press [SETUP] to return to TV mode.

1 Select “USER’S SET UP”

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

Press [SETUP].

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press [K / L] to point to “USER’S

SET UP”, then press [ENTER].

INDEX SEARCH

2 Set “AUTO RETURN” to [ON]

Press [K / L] to point to “AUTO

RETURN”, then press [ENTER]

until [ON] appears.

USER’S SET UP

–

RENTAL

[OFF]

[ON]

REPEAT PLAY

AUTO RETURN

3 Auto Return will begin

When all the timer recordings are completed, the unit

will rewind to the beginning of the recorded pro-

gram(s).

NOTE:

If you press [POWER] while tape is rewinding,

the Auto Return will stop.

•

4 Watch the recorded program

Press [PLAY O].

TO CANCEL THE AUTO RETURN

MODE

Repeat steps 1 to 2 and select [OFF] using

[ENTER].

Even if there is a power failure of any kind, the

unit will retain its memory for this feature.

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press [DISPLAY]. Each time you press

[DISPLAY], the TV screen will change as follows:

When the Closed Caption mode is OFF:

When the Closed Caption mode is ON:

Counter mode: After 5 seconds, only the counter

remains. To clear it, press [DISPLAY].

Clock mode: After 5 seconds, only the clock and

the channel number remain. To clear them, press

The On Screen Display disappear after 5 seconds.

This is true even if [MUTE] or [PAUSE F] is

pressed while recording.

•

[DISPLAY].

OFF mode

Clock/Counter mode

OFF mode Counter mode

Clock mode

STOP

5:40PM

CH2

STOP

5:40 PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

CATV channel

TV Display

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

CATV channel

TV Display

CATV channel

TV Display

W+55 W+56 W+57 W+58

91 92 93 94

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

CATV channel

TV Display

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS

Recorded

Playable

discs

Disc size

Region code

Disc types

Mark (logo)

signals

DVD-Video

* 1,2,4,6,10,11

Example

12 cm

8 cm

Title 1

Title 2

DVD-RW

DVD-R

Digital video

(MPEG2)

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1

Chapter 2

* 1,3,4,5,6

7,9,10

DVD+RW

DVD+R

* 1,3,4,5,6,8,9,10

Audio CD

* 4,6,10

Audio CD

Example

12 cm

8 cm

Digital audio

Track 1

Track 2

Track 5

Track 6

Track 3

Track 4

CD-RW

CD-R

* 4,5,6,9,10

is a trademark of DVD Format/Logo Licensing Corporation.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot

be played back.

*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.

*3: Discs recorded in the VR (Video Recording) format cannot be played back.

*4: Scratched or stained discs may not be played back.

*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD

recorder. However, depending on the recording status of a disc, the disc may not be played back at all or

normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with

the DVD recorder. Refer to the manual accompanying the DVD recorder.

*8: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be

played back at all or normally (the picture or sound may not be smooth, etc.).

*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not

play back properly.

*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.

*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-

mat can only be played back on unit with the same region code.

UNPLAYABLE DISCS

¡NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /

DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3

¡On the following disc, the sound MAY NOT be heard.

Super Audio CD

NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

¡Any other discs without compatibility indications

–

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING A DISC

BASIC PLAYBACK

GENERAL FEATURES

DVD-V CD

DVD-V

VD may contain menus to navigate the disc and

Getting started

access special features. Press the appropriate

Number buttons or [K / L / s / B] to highlight

your selection in the DVD main menu and press

[ENTER] to confirm.

¡Turn on the power of amplifier and any other com-

ponents, if necessary.

Press [POWER].

¡The power will turn on.

NOTES:

¡Select DVD mode by pressing [SELECT], then

Press [A OPEN/CLOSE] to open disc load-

ing tray.

operate the DVD functions.

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

Place the chosen disc in the tray, with the

label facing up.

DISC MENU

DVD-V

Press [DISC MENU].

¡The DVD main menu will appear.

¡If the feature is not available, symbol may appear

on the TV screen.

¡If disc menu is available on the disc, audio language,

subtitle options, chapters for the title and other

options will appear for selection.

Press [PLAY O].

¡The tray will close automatically and playback will

then start from the first chapter or track of the disc.

¡Closing the disc tray manually or by pressing

[A OPEN/CLOSE] also starts playback.

¡If the playback does not start automatically, press

[PLAY O].

Press [K / L / s / B] to select an item and

press [ENTER] to confirm selection.

¡When you playback a DVD which features a title

menu, it may appear on the screen. In this case,

refer to “TITLE MENU” on this page.

TITLE MENU

Press [STOP C] to stop playback.

DVD-V

Press [TITLE].

NOTES:

¡The title menu will appear.

¡If the feature is not available, symbol may

appear on the TV screen.

¡When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and

then the TV picture and sound appears in about 4

seconds. Similarly, when [POWER] is pressed to

turn off in the DVD mode, this mode shuts down

first and then the unit is turned off.

¡A “prohibited icon” may appear at

the top-right on the TV screen

during operation, warning that a

Press [K / L / s / B] to select an item, and

press [ENTER] to confirm selection.

CALLING UP A MENU SCREEN

DURING PLAYBACK

prohibited operation has been

encountered by the DVD or the

disc.

¡Press [DISC MENU] to call up the DVD menu.

¡Press [TITLE] to call up the title menu.

¡With DVDs that use titles for playback program

signals, playback may start from the second title or

it may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

NOTE:

¡Contents of menu and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

SLOW FORWARD /

SLOW REVERSE

RESUME

DVD-V

During playback, press [STOP C].

¡Resume message will appear on the TV screen.

During playback, press [PAUSE F].

Press and hold [D] or [E] for a few sec-

onds.

Press [PLAY O], playback will resume from

the point at which playback was stopped.

¡“

1” or “

1” appears on the screen.

¡To cancel resume, press [STOP C] twice.

¡The resume information stays on even when the

power is turned off.

To select another speed, repeat step 2 until

your required speed number appears on the

screen.

PAUSE

¡Slow forward or reverse speed varies with the disc.

Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).

DVD-V

When you press buttons on the main unit, use

[SEARCH ].

During playback, press [PAUSE F].

¡Playback will pause and sound will be muted.

To return to normal playback, press [PLAY O].

To continue playback, press [PLAY O].

ZOOM

STEP BY STEP PLAYBACK

DVD-V

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

During playback, press [PAUSE F].

¡Playback will pause and sound will be muted.

Press [ZOOM] during playback.

¡Playback will continue.

The disc goes forward by one frame each

time [PAUSE F] is pressed.

Press [ZOOM] repeatedly to select the

required zoom factor: ZOOM1, ZOOM2,

ZOOM3 or OFF.

To exit step by step playback, press [PLAY O].

FAST FORWARD /

FAST REVERSE

Press [K / L / s / B] to move the zoomed

picture across the screen.

DVD-V

To exit zoom mode, press [ZOOM] to OFF.

NOTES:

During playback, press and hold [D] or

[E] for a few seconds.

¡Zooming function does not work while disc menu is

shown.

¡“ D 1” or “E 1” appears on the screen.

¡Zooming function is not available on some discs.

¡It may take several seconds to slide the zoomed pic-

ture.

¡The picture may be distorted if you operate other

functions repeatedly (ex. [PAUSE ] or [E], etc.)

in the zoom mode.

To select another speed, repeat step 1 until

your required speed number appears on the

screen.

¡For DVDs, fast forward/reverse search speed is dif-

ferent depending on the disc. Approximate speed is

1 (×2), 2 (×8), 3 (×20), 4 (×50) and 5 (×100).

¡For Audio CDs approximate speed is 1 (×2), 2 (×8)

and 3 (×30).

¡When you press buttons on the main unit, use

[SEARCH E / D].

To return to normal playback, press [PLAY O].

–

Download from Www.Somanuals.com. All Manuals Search And Download.

SEARCH FUNCTION

TRACK SEARCH

TIME SEARCH

DVD-V

There are three ways to begin playback on an Audio

CD at a specific track.

During playback, press [SEARCH MODE]

three times (CD: twice) to display the Time

Search on the TV screen.

Using the Number buttons

Within 30 seconds, enter a desired disc

time using the Number buttons.

Press the Number buttons to enter the

desired track number.

¡Playback will start at the specified time.

¡Press [CLEAR] to erase the incorrect input.

¡When there is no need to enter a number, “0”

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press [3]).

appears automatically. For example, “ 0 : 0

”

- - -

¡To play track 26, press [+10], [2], [6].

appears in the Time Search display if the total time

of the track or title is less than 10 minutes.

Using [SEARCH MODE]

MARKER SETUP SCREEN

Press [SEARCH MODE].

¡The track search display appears.

DVD-V

Within 30 seconds, select the desired track

number using the Number buttons.

Use markers to memorize your favorite places on a disc.

Press [SEARCH MODE] four times

(CD: three times) during playback.

¡For single digits press [0] first, if the total track of

the disc is 10 tracks or more.

¡Playback will start at the selected track.

¡The display screen and Markers will appear on the

TV screen.

Using [H / G]

Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,

During playback, press [G] to move the next track.

Press it repeatedly to skip subsequent tracks. Press

[H] to go back to beginning of the current track.

Press it repeatedly to go to the previous tracks.

¡If [H / G] is pressed while the playback is

paused, the playback will be paused again after

skipping to the next track.

or 10 and ensure that “

appears in the display.

”

- - - - - - - -

When you reach the desired point, press

[ENTER].

¡The Title or Track and elapsed playing time will

appear in the TV screen.

NOTE:

¡[H / G] are not operative when playback is

stopped.

To return to the Marker later, press

[SEARCH MODE] four times (CD: three

times) during playback and press [s / B]

to choose the desired marker, then press

[ENTER].

TITLE / CHAPTER SEARCH

DVD-V

Press [SEARCH MODE] once for the

Chapter search, twice for the Title search

NOTES:

¡Operations which erase all Markers:

– Opening the disc tray.

during playback.

_/2

– Turning off the power.

– Pressing [SELECT].

– Selecting “AC” at step 2 and pressing [ENTER].

¡To clear a marker:

Enter the desired chapter/title number using

the Number buttons.

– Press [s / B] to select a cursor on to the marker

number and press [CLEAR].

¡You can mark up to 10 points.

¡Playback will start at the selected chapter or title.

¡Press [CLEAR] to erase the incorrect input.

¡For single digits press [0] first, if the total number of

chapter or title of the disc is 10 or more.

Press [SEARCH MODE] or [RETURN] to exit.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIAL PLAYBACK FUNCTION

REPEAT

PROGRAM

You may determine the order in which tracks will play.

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

DVD-V

In the stop mode, press [MODE].

¡The “PROGRAM” screen will appear.

To activate the repeat function, press [REPEAT]

during playback.

Press [▲ / ▼] to select a track, then press

¡The repeat mode changes as described below every

time you press the button.

[ENTER].

¡Press [CLEAR] to erase the

most recently entered track.

¡If the entire Program cannot be

displayed at once on a screen,

“G” appears to go to the next

page and “H” appears to go

back to the previous page.

TOTAL 1:03:30

3:30

5:10

CHAPTER

TITLE

OFF

(repeat off)

10 4:20

11 3:00

12 3:20

17 4:10

22 2:50

2/3

(current chapter repeat) (current title repeat)

1/4

NOTES:

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

Repeat step 2 until you have selected all the

tracks you want to play in the program.

Press [PLAY O] to play the programmed tracks.

REPEAT TRACK

NOTES:

¡While the program is being played back, pressing

[STOP C] works as follows.

To activate the repeat function, press [REPEAT]

during playback.

¡Press [STOP C] once and then [PLAY O] again,

playback will restart from the point where

[STOP C] was pressed. (Program continued)

¡Press [STOP C] twice and then [PLAY O] again,

playback will restart from the track in the usual

way. (Program canceled)

¡The repeat mode changes as described below every

time you press the button.

TRACK

ALL

OFF

(repeat off)

(current track repeat)

(entire disc repeat)

¡Up to 99 tracks can be entered.

¡To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at step 2.

¡If you like to repeat the current track in the program,

NOTES:

press [REPEAT] several times until “

TRACK”

¡Repeat setting will be cleared when moving to other

appears during playback. If you like to repeat the

track.

entire program press [REPEAT] several times until

¡Repeat playback does not function during A-B

repeat playback.

“

ALL” appears during playback.

A-B REPEAT

RANDOM PLAYBACK

DVD-V CD

¡“

Press [A-B] at your chosen starting point.

This function shuffles the playing order of tracks

A-” appears briefly on the TV screen.

instead of playback in the sequence.

In the stop mode, press [MODE] twice.

¡“

Press [A-B] again at your chosen end point.

¡“RANDOM” screen appears.

A-B” appears briefly on the TV screen, and

RANDOM

CD-DA

TOTAL 0:45:55

the repeat sequence begins.

RANDOM PROGRAM

no indication

To exit the sequence, press [A-B].

PLAY

NOTES:

¡The A-B repeat section can only be set within the cur-

rent title (for DVDs) or current track (for Audio CDs).

¡A-B repeat is not available with some scenes in DVD.

¡To cancel the A point which was set, press

[CLEAR].

Press [PLAY O] to start random playback.

NOTE:

If you like to repeat the current track in the random

selection, press [REPEAT] several times until

“

TRACK” appears during playback. If you like to

¡A-B repeat playback does not function during title,

chapter, track or all repeat playback.

repeat the entire random selection press [REPEAT]

several times until “

back.

ALL” appears during play-

–

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE SETTINGS

SUBTITLE LANGUAGE

AUDIO LANGUAGE

DVD-V

The unit allows you to select a language during DVD

disc (if multi languages are available) playback.

The unit allows you to select a language for subtitles

during DVD disc (if available) playback.

Press [AUDIO] during playback.

Press [SUBTITLE] during playback.

1.ENG Dolby D 3/2.1ch 48k/3

¡The subtitle language will

appear on the display bar at

the top of the TV screen.

1.ENG/6

Press [AUDIO] repeatedly to select your

desired language.

Press [SUBTITLE] repeatedly to select your

desired subtitle language.

NOTE:

To turn off subtitles, press [SUBTITLE]

repeatedly until “OFF” appears.

¡Pressing [AUDIO] may not work on some DVDs

with multiple audio languages (e.g. DVDs which

allow audio language setting on the disc menu).

NOTES:

¡Pressing [SUBTITLE] may not work on some

DVDs with multiple subtitle languages. In this

case, set it on the disc menu. (Operation varies

between discs. Refer to the manual of the disc.)

¡If the desired language is not shown after pressing

[SUBTITLE] several times, the disc does not have

subtitles in that language.

STEREO SOUND MODE

Press [AUDIO] repeatedly during playback to

select between “STEREO”, “L-ch” or “R-ch”.

¡When “NOT AVAILABLE”

NOT AVAILABLE

appears on the TV screen, it

STEREO

means no subtitle is recorded

on the scene.

¡If you choose a language that has a 3 letter lan-

guage code, the code will be displayed every time

you change the Subtitle language setting. If you

choose any other languages, “---” will be displayed

instead. (Refer to page 42.)

STEREO - both right and left channels are active (stereo)

L-ch - only left channel is active

R-ch - only right channel is active

–

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA ANGLE

VIRTUAL SURROUND

DVD-V

Some DVD discs contain scenes which have been shot You can enjoy surround-sound effect over two speak-

simultaneously from various angles. You can change ers on this unit.

the camera angle when the “

screen.

” icon appears on the

Press [MODE] twice (CD: once) during play-

back.

OFF

Press [ANGLE] during playback.

¡The selected angle will be displayed on the display

bar at the top of the screen.

1 / 8

Press [ENTER] to set it “1” (Natural effect),

“2” (Emphasized effect) or “OFF”.

¡If the “ANGLE ICON” setting is “OFF” in the

“OTHERS” menu, the “

(Refer to page 44.)

Press [RETURN] to exit.

” icon will not appear.

NOTE: (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

Press [ANGLE] repeatedly to select your

desired angle.

BLACK LEVEL SETTING

DVD-V

Adjust the Black Level Settings to make the black

parts of the picture brighter.

Press [MODE] during playback.

OFF

Press [ENTER] to switch “ON”or “OFF”.

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

(Initial setting)

Press [MODE] twice or [RETURN] to exit.

NOTE:

¡The setting will be saved even if the unit is turned

off.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

THE ON-SCREEN INFORMATION

DVD-V

You can check the information about the current disc by pressing [DISPLAY].

For DVD-Vs

For Audio CDs

Press [DISPLAY] during playback to show

current Chapter.

Press [DISPLAY] during playback to show

the current Track.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

¡The elapsed and remaining

playing time of the current

track will be displayed.

4/12 0:03:21 - 0:02:15

9/49

0:00:00 -0:03:30

Press [DISPLAY] again to show current Title.

Press [DISPLAY] again to show current Total

Track.

¡The elapsed and remaining

playing time of the current

title will be displayed.

1/3 0:00:00 - 1:23:45

¡The elapsed and remaining

playing time of the total track

will be displayed.

4/12 0:13:45 - 0:45:40

Press [DISPLAY] again.

Press [DISPLAY] again to exit.

¡The bit rate and the current

repeat setting will be dis-

played.

¡If you are playing a dual layered disc, the layer

number will also be displayed.

NOTE:

¡When you are playing a disc in PROGRAM or

RANDOM mode, “ PROGRAM” (or RANDOM)

(L0: Layer 0 is playing. L1: Layer 1 is playing)

will be displayed at step 2.

PROGRAM

Press [DISPLAY] again to exit.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING THE DVD SET UP ITEMS

Language

Code Language

Code

CUSTOM MENU

A-B

L-N

Abkhazian

Afar

4748 Laothian

4747 Latin

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

DVD-V Afrikaans

Amharic

4752 Latvian;Lettish

6563 Lingala

4759 Lithuanian

4764 Macedonian

5471 Malagasy

4765 Malay

Albanian

You can change the DVD player’s settings.

Arabic

Press [SETUP] twice in the stop mode so

that the DVD SETUP menu appears.

Armenian

Assamese

Aymara

4771 Malayalam

4772 Maltese

4847 Maori

Azerbaijani

Bashkir

Basque

¡Press [L] to select “CUSTOM”

then press [ENTER].

SETUP

QUICK

CUSTOM

INITIALIZE

5167 Marathi

Bengali;Bangla

Bhutani

Bihari

4860 Moldavian

5072 Mongolian

4854 Nauru

NOTE:

¡If the menu does not appear, press [PLAY O] first,

then press [STOP C]. Make sure the disc is in the

stop mode, then slowly press [SETUP] twice.

Bislama

4855 Nepali

Breton

4864 Norwegian [NOR]

O-R

Bulgarian

Burmese

Byelorussian

4853

5971 Occitan

4851 Oriya

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

C-E

Oromo(Afan)

5759 Panjabi

4947 Pashto;Pushto

7254 Persian

4961 Polish

5464 Portuguese [POR]

4965 Quechua

Select the desired item.

Cambodian

Catalan

¡Press [K / L] to select the desired item then press

[ENTER] to confirm.

Chinese [CHI]

Corsican

Croatian

Refer to the pages below to set up each item.

Czech

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

5047 Rhaeto-Romance

6058 Romanian [RUM]

5160 Russian [RUS]

SETUP

CUSTOM

P 42 Step

LANGUAGE

DISPLAY

AUDIO

PARENTAL

OTHERS

P 43 Step

5161

P 43 Step

5166 Samoan

Sangho

5261 Sanskrit

5256 Scots Gaelic

5255 Serbian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

F-H

P 44 Step

Faroese

Fiji

P 44 Step

Finnish [FIN]

French [FRE]

Frisian

5264 Serbo-Croatian

5271 Sesotho

5358 Setswana

5747 Shona

LANGUAGE SETTING

Galician

Follow steps to in the “CUSTOM MENU” section

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

above.

5051 Sindhi

5158 Singhalese

5758 Siswat

5360 Slovak

Press [K / L] to select the desired item then

press [ENTER].

Gujarati

Hausa

Hebrew

5367 Slovenian

5447 Somali

5569 Spanish [SPA]

5455 Sundanese

5467 Swahili

SETUP

LANGUAGE

AUDIO:

AUDIO

SUBTITLE

DISC MENU

ORIGINAL

OFF

ENGLISH

Sets the audio language.

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

SUBTITLE:

Swedish [SWE]

Sets the subtitle language.

DISC MENU:

5565

5560 Tagalog

5547 Tajik

5551 Tamil

5557 Tatar

5347 Telugu

5566 Thai

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Sets the language for DVD menu.

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Press [K / L] to select a setting then press

[ENTER].

SETUP

LANGUAGE

5647 Tibetan

5669 Tigrinya

5760 Tonga

5765 Tsonga

5757 Turkish [TUR]

6469 Turkmen

5771 Twi

AUDIO

¡If “OTHER” is selected on the

“AUDIO”, “SUBTITLE” or

“DISC MENU” screen, press

four-digit number to enter the

code for the desired language.

(Refer to the language code

list.)

ORIGINAL

ENGLISH

FRENCH

Kazakh

Kinyarwanda

Kirghiz

Kirundi

SETUP

6460

U-Z

SUBTITLE

OFF

ENGLISH

FRENCH

Korean [KOR]

Kurdish

5761 Ukrainian

5767 Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

¡Only the languages supported

by the disc can be selected.

SETUP

DISC MENU

ENGLISH

FRENCH

SPANISH

Yoruba

Zulu

Press [SETUP] to exit the menu.

If you choose a language that has a 3 letter language

code, the code will be displayed every time you change

the AUDIO or SUBTITLE language setting above. If

you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

NOTES:

¡Language Setting for Audio and Subtitle are not

valid for some discs due to default setting of the

disc. In this case, set them by pressing [AUDIO] and

[SUBTITLE]. (Refer to page 39.)

¡If you select a language that is not supported by the

disc, subtitle will automatically be set OFF and the

first item of the audio languages will be automatically

set.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY SETTING

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affects during the playback of DVD

discs.

Follow steps to in the “CUSTOM MENU” section

on page 42.

Press [K / L] to select the below items then

press [ENTER].

Follow steps to in the “CUSTOM MENU” section

on page 42.

TV MODE:

QUICK

Press [K / L] to select the below items then

press [ENTER].

You can change certain aspects of the DVD display

screens and on-screen messages on the TV screen.

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

DRC (Dynamic Range

Control):

¡To compress the range of

soft to loud sound.

¡4:3 LETTER BOX (default):

To show black bars on top

and bottom of the screen.

SETUP

DISPLAY

BITSTREAM

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

¡4:3 PAN & SCAN: To show

a full height picture with both sides trimmed.

¡The default setting is “ON”.

SETUP

AUDIO

DOWN SAMPLING:

¡ON : Output in 48 kHz.

(default)

DRC

DOWN SAMPLING

DOLBY DIGITAL

BITSTREAM

STILL MODE

This function allows you to adjust picture resolution

and quality in the still mode.

¡OFF : Output the original

sound.

SETUP

DISPLAY

¡AUTO (default):

When playing disc with copyright Protection

¡If you select “OFF”, copyright protection will be

activated and sound will be down sampled at 48kHz.

Automatically select the best

resolution setting (FRAME

or FIELD) based on the data

characteristics of the pictures.

¡FIELD: Select “FIELD” when the pictures are still

unstable even if “AUTO” is selected.

FIELD stabilizes the pictures, although the picture

quality may become coarse due to the limited

amount of data.

TV MODE

STILL MODE

4:3 LETTER BOX

AUTO

SETUP

DRC

DOWN SAMPLING

DOLBY DIGITAL

AUDIO

DOLBY DIGITAL:

QUICK

BITSTREAM

Set to “BITSTREAM” when

the unit is connected to a

Dolby Digital Decoder.

¡BITSTREAM: Output a Dolby Digital signal

¡FRAME: Select “FRAME” to display relatively

motionless pictures in higher resolution.

FRAME improves the picture quality, although it

may unstabilizethe pictures due to simultaneous

output of two field data.

(default)

¡PCM: Convert the Dolby Digital to PCM

(2 channel stereo)

Press [SETUP] to exit the menu.

QUICK MENU

¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the

QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 42.

LANGUAGE SETTING FOR THE ON-SCREEN MENUS

¡You can access the TV/VCR SETUP menu by pressing [SETUP] from the DVD mode. Refer to

“MENU LANGUAGE” on page 21 to change the language for the on-screen menus.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL CONTROL

IF YOU FORGET THE PASSWORD

Parental Control limits the disc viewing that exceed

your setting (with a password or playback will stop).

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

Press the Number buttons [4], [7], [3], [7] at

step 3. Then enter your new password.

¡Password will be cleared and parental level will be

set to “ALL”.

PARENTAL LEVEL

Proceed with steps 4 to 6 again.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

OTHER SETTINGS

Follow steps to in the “CUSTOM MENU” section

on page 42.

Follow steps to in the “CUSTOM MENU” section

on page 42.

Press [K / L] to select the below items,

Enter your four-digit password then press

[ENTER].

then press [ENTER].

SETUP

OTHERS

SETUP

PARENTAL

PASSWORD

ANGLE ICON

Enter current password.

AUTO POWER OFF ON

ANGLE ICON:

¡Press [ENTER] repeatedly to turn Angle icon

Press [K / L] to select “PARENTAL LEVEL”

“ON” or “OFF”.

then press [ENTER].

SETUP

PARENTAL

¡The default setting is “ON”.

PARENTAL LEVEL

PASSWORD CHANGE

ALL

AUTO POWER OFF:

¡Press [ENTER] repeatedly to turn Auto Power off

“ON” or “OFF”.

The default setting is “ON” and the screen saver pro-

gram starts when there is no input from the unit for 5

minutes in the stop mode. After the screen saver pro-

gram is activated for 15 minutes, the power is auto-

matically turned off.

Press [K / L] to select the desired level

then press [ENTER].

SETUP

PARENTAL

PARENTAL LEVEL

ALL

7 [NC-17]

6 [R]

Press [SETUP] to exit the menu.

NOTES:

When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the pass-

word. (in the event you forget the password, see below)

INITIALIZE

DVD-V

¡To change the password, press [K / L] to select

“PASSWORD CHANGE” at step 4 then press

[ENTER]. Enter the four-digit password, then

press [ENTER].

This allows you to return all selections of SETUP

(except for “PARENTAL” and menu language) to

their default settings.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

Press [SETUP] twice in the stop mode so

that the “INITIALIZE” menu appears.

Press [K / L] to select “INITIALIZE” then

¡Record the password in case you forget it.

press [ENTER].

SETUP

CONTROL LEVELS

QUICK

CUSTOM

INITIALIZE

ALL

All parental lock is cancelled.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

Press [K / L] to select “YES” then press

[ENTER] twice.

Levels 7 to 2

SETUP

INITIALIZE

All the settings (except for

“PARENTAL” and menu

language) will be cleared.

¡To cancel the initialization,

select “NO”.

Only DVD software intended for general use and

children can be played back.

Initialize?

YES

Level 1

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Press [SETUP] to exit the menu.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING GUIDE

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-

sulting the following checklist.

PROBLEM

CORRECTIVE ACTION

Make sure the power plug is connected to an AC outlet.

Make sure the power is turned on.

Check if the power plug is connected to an AC outlet.

Check the batteries in the remote control.

Aim the remote control directly at the remote sensor. If necessary,

remove all the obstacles between the sensor and the remote control.

You have to be within 23 feet of the unit.

Check if the correct mode is selected. If not switch the mode by

pressing [SELECT], whichever you need.

No power

•

No operation by infrared remote

control

•

TV/VCR Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked

possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture or sound

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Press [SELECT] to select TV mode.

Then try other TV feature.

•

Let the unit program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Check for broken pin of the antenna cable.

Adjust volume control on remote control or main unit.

Press [MUTE] to restore sound.

•

No picture or poor picture on the

unit

•

No sound or poor sound

Bars On Screen

•

If outside antenna is being used, check for broken wire.

Check for local interference.

Picture Distorted or Blurred

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Try a new channel, if OK, then possible station trouble.

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “COLOR” control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Adjust “CONTRAST” & “BRIGHT” control.

Try a new channel, if OK, then possible station trouble.

Is antenna connected to jack on the back of the set?

If outside antenna is being used, check for broken wire.

Check for local interference.

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor

Adjust “CONTRAST” & “BRIGHT” control.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM

Picture OK, Sound Poor

CORRECTIVE ACTION

Try a new channel, if OK, then possible station trouble.

Check for local interference.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the unit’s clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

Adjust tracking control for a better picture using [CHANNEL K / L]

on the unit.

Head cleaning may be necessary. Refer to “AUTO HEAD

• CLEANING” on page 48.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

•

Timer recording is not possible

Cannot go into Record mode

•

Playback picture is partially noisy

•

No picture but the audio is OK in

playback

No operation by infrared Remote

Control

Video or color fades in and out

when making a copy of a video tape

•

copy guard protection.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the unit away from the appliances,

the unit can repair itself automatically. If you want to repair immedi-

ately, unplug the power cord, then plug it in again 30 minutes later

or so. This automatically resets the unit.

•

Different color marks on screen

•

CLOSED CAPTION PROBLEM

POSSIBLE REMEDY

Misspelling in captions

Error committed by the closed captioning production company.

• Possible in a live broadcast. Not in case of a prerecorded program.

•

Text is not shown in its entirety or

a delay occurs from what is being

said.

A few seconds of delay is common for live broadcast.

Display capacity may not exceed 220 words per minute. If a dialogue

• exceeds that rate, selective editing is used to insure that the captions

• remain up-to-date with the current TV screen dialogue.

•

Captions scrambled with white

boxes

Caused by interferences of building, power lines, thunderstorms, etc.

•

No captions in a program which

must contain closed caption

The broadcast may use a time compression process to speed up the

• program. The decoder cannot read the compressed information and

• captions will be lost.

•

No captions in a prerecorded

videotape which indicated closed

captions included.

Possibility of a illegal copy or an erroneous copying process

• accidentally performed by the fabricator.

•

Black box in the TV screen

You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or

• Caption “OFF”.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Mode

PROBLEM

CORRECTIVE ACTION

Insert a correct video disc that plays on this unit.

Press [SELECT] to select DVD mode, then try other DVD feature.

Insert the disc.

No picture

•

Disc cannot be played

Clean the disc.

Place the disc correctly, with the label side up.

Cancel the parental lock or change the control level.

Connect the audio cables firmly.

Turn the power of the audio component on.

Correct the audio output settings.

Correct the input settings on the audio component.

This unit does not support DTS audio. This is not a malfunction.

There are some cases where pictures may be slightly distorted,

which are not a sign of a malfunction.

No sound

No DTS audio is output

Distorted picture

Although pictures may stop for a moment, this is not a malfunction.

The selected language is not available for audio or subtitles on the

DVD. (This is not a malfunction.)

•

Audio or subtitle language

does not match the set up

The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-

•

era angles. (This is not a malfunction.)

Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected

•

changed

language. (This is not a malfunction.)

“Prohibited icon” appears on the

screen, prohibiting an operation

CD sound dropout

No CD reproduction

DVD picture dropout

DVD picture freeze

That operation is prohibited by the unit or the disc.

(This is not a malfunction.)

Scratched disc. Replace the disc with an unscratched one.

•

DVD picture in mosaic

No DVD reproduction

NOTES:

Some functions are not available in specific modes, but this is not a malfunction. Read the description in

this Owner’s Manual for details on correct operations.

•

Playback from a desired track and random playback are not available during program playback.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

CABINET CLEANING

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line mentioned on the

front page, to locate an Authorized Service Center.

NOTES:

Wipe the front panel and other exterior surfaces of

the unit with a soft cloth immersed in lukewarm

water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the unit. Such chemicals may

cause damage and discoloration to the exposed sur-

faces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clearer picture.

•

Should your unit become inoperative, do not try to

•

correct the problem by yourself. There are no user-

serviceable parts inside. Turn off, unplug the power

cord and please call our help line mentioned on

the front page, to locate an Authorized Service

Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your unit may need to be

cleaned.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

If the unit still does not perform properly when it is operated, while referring to the relevant sections and to

“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.

•

Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup

unit.

DISC HANDLING

Handle the discs so that fingerprints and dust do

not adhere to the surfaces of the discs.

To clean-off, use a soft cloth.

•

Do not use a hard cloth since this will mar the disc.

Wipe the disc in a straight line from center to edge.

Never wipe with a circular motion.

Do not use detergent or abrasive cleaning agents.

Always store the disc in its protective case when it

is not used.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

Sound output:

2 speakers, 1W, 8 ohm

TV/VCR

CRT:

19 inch in-line gun,

90˚ deflection tube

NTSC-M

OTHER SPECIFICATIONS

Terminals

Television system:

Closed caption system :§15.119/FCC

Antenna input:

VHF/UHF/CATV

75 ohm unbalanced (F-type)

RCA connector [ 1

RCA connector [ 2

Video Heads:

Tape width:

Tape speed

SP:

LP:

SLP:

Tuner channel

TV VHF Low:

TV VHF High:

TV UHF:

CATV

Rotary four-head

1/2 inch

Video input:

Audio L/R input:

Headphone:

Coaxial digital

audio output:

1/8" stereo (3.5mm)

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

One pin jack,

500m Vpp (75 ohm)

Digital encoded

Remote control:

#2~#6

#7~#13

#14~#69

infrared light system

Operating

temperature:

5˚C to 40˚C

(41˚F~104˚F)

Power requirements: AC 120V, 60Hz

Power consumption

VHF:

MID band:

SUPER band:

HYPER band:

A5~A1, A~I

J~W

W+1~W+84

(Maximum):

Picture tube:

Dimensions:

90W

19"

H :19-11/16"(500mm)

W:21-7/8" (556mm)

D :18-3/4" (477mm)

45.2 lbs. (20.5kg)

Weight:

DVD

Product type:

Discs:

DVD Player

DVD video, Audio CD

Output signal format: NTSC color

Designs and specifications are subject to change without notice.

If there is a discrepancy between languages, the default language will be English.

•

–

Download from Www.Somanuals.com. All Manuals Search And Download.

12. Indicador de grabación

INDICE

Parpadea durante la grabación. Se ilumina durante el

modo de espera de grabación controlada por

temporizador.

■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 50

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 51

■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 51

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 51

CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 52

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

13. Botón I REC/OTR (Panel frontal)

Presione para empezar la grabación manual. Presione

repetidamente para empezar la grabación instantánea (OTR).

Botón RECORD (Mando a distancia)

Presione para empezar la grabación manual.

EQUIPADO CON TOMAS DE ENTRADA DIGITAL.

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

14. Botón E REW (para TV/VCR)

Presione para rebobinar la cinta o para ver la imagen

rápidamente en dirección de retroceso durante el modo

de reproducción. (Búsqueda en dirección de retroceso)

SECCIÓN DE TV/VCR

15. Botón F.FWD D (para TV/VCR)

■ FUNCIONES Y AJUSTES DE TV. . . . . . . . . . . . . . . . . 53

PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 53

IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

■ GRABACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

GRABACIÓN NORMAL . . . . . . . . . . . . . . . . . . . . . . . . 54

Presione para adelantar rápidamente la cinta o para ver la

imagen rápidamente en dirección de avance durante el modo

de reproducción. (Búsqueda en dirección de avance)

16. Botón

A STOP/EJECT

Presione para detener la cinta. Presione en el modo de

parada para retirar la cinta de la unidad.

SECCIÓN DE DVD

17. Ventanilla del sensor de mando a distancia

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

18. Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar

en privado.

CONTROLES DE

19. Toma de entrada VIDEO

OPERACIÓN Y FUNCIONES

Conecte aquí la toma de salida de video de una

videocámara o de una videograbadora.

20. Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una

videocámara o de una videograbadora.

• Consulte la figura 1 de la página 9 para el

panel frontal de la unidad

• Consulte la figura 2 de la página 9 para el

mando a distancia

21. Compartimiento del cassette

• Consulte la figura 3 de la página 10 para la

vista posterior

22. Botón PICTURE

Presione para ajustar la imagen.

23. Botones numéricos

1. Botón POWER

Presione para encender y apagar la unidad.

Modo TV/VCR:

Presione dos cifras para acceder directamente al canal

deseado.

2. Botones VOLUME (VOL.)

Presione para controlar el nivel de volumen del DVD y

el televisor.

No olvide presionar [0] antes de elegir un canal de una

sola cifra.

Botón +100

Presione para seleccionar canales de televisión por

cable cuyo número sea superior a 99.

Modo DVD:

Presione para introducir el número deseado.

Botón +10

Presione para introducir números superiors a 9.

3. Botones SKIP H / G (para DVD)

Presione una vez para omitir capítulos o pistas y

desplazarse a un punto específico.

Botones SEARCH E / D (para DVD)

Mantenga el botón presionado para cambiar la

velocidad de reproducción en avance o retroceso.

4. Botón B PLAY

Inicia la reproducción del contenido del disco o cinta.

5. Botón C STOP

(Panel frontal) Detiene la operación del disco.

(Mando a distancia) Detiene la operación del disco o el

casete.

6. Botón A OPEN/CLOSE

Presione para insertar un disco en la bandeja o retirarlo

de ella.

24. Botón PAUSE

Hace una pausa en la reproducción del disco o cinta.

25. Botón SPEED

Presione para seleccionar la velocidad de grabación

deseada: SP/SLP.

26. Botón C.RESET

Presione para poner el contador en 0:00:00.

Presione también para cancelar un ajuste de programa

de temporizador.

7. Bandeja de carga del disco

8. Indicador DVD

27. Botón DISPLAY

Se ilumina durante el modo DVD.

Modo TV/VCR:

9. Botón SELECT

Indica el contador o el número del canal y la fecha

actual en la pantalla del televisor.

Modo DVD:

Presione para cambiar al modo TV/VCR, modo de

entrada externa o modo de DVD. El modo

seleccionado (TV/VCR o DVD) se visualiza en el

indicador del panel delantero.

Indica el estado actual en la pantalla del televisor.

28. Botón SETUP

10. Indicador TV/VCR

Presione para entrar o salir del menú de configración

de televisor o DVD.

Se ilumina durante el modo TV/VCR.

11. Botones CHANNEL (CH.)

29. Botón TITLE

Utilice para seleccionar canales memorizados.

Para visualizar el menú de títulos.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

30. Botón CLEAR

PARA INSERTAR LAS PILAS

Presione para cancelar o borrar un ajuste entrado actualmente.

31. Botón MODE

1) Abra la cubierta del compartimiento de las pilas

empujando la cubierta del mando a

distancia en el sentido de la flecha.

2) Inserte 2 pilas “AA” en el

Presione para llamar la pantalla de la reproducción

programada o la de reproducción aleatoria en el modo

de parada.

Presione para llamar la pantalla de ajuste del nivel del

negro o la pantalla de sonido ambiental durante la

reproducción.

compartimiento de las pilas, en el

sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

32. Botón SEARCH MODE

Presione para localizar un punto deseado.

33. Botón AUDIO (modo DVD)

Presione para seleccionar un modo de sonido o idioma

de audio deseado.

PREPARACIÓN PARA LA

UTILIZACIÓN

34. Botón SUBTITLE

Presione para seleccionar el idioma de subtítulos

deseado.

35. Botón REPEAT

CONEXIONES DE ANTENA/CABLE

Repite la reproducción del disco, título, capítulo o pista

actual.

Consulte la figura 4 de la página 12

36. Botón ANGLE

Presione para cambiar el ángulo de la cámara y ver la

secuencia que se está reproduciendo desde un ángulo

diferente (si existe).

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención

del instalador de sistemas CATV para que tenga

en cuenta el Artículo 820-40 de la NEC, que

proporciona recomendaciones para hacer una

conexión a tierra apropiada y, en particular,

especifica que la tierra del cable debe conectarse

al sistema de puesta a tierra del edificio, tan cerca

del punto de entrada del cable como sea posible.

37. Botón A-B (modo DVD)

Repite la reproducción de una sección seleccionada.

38. Botón RETURN

Permite volver a la pantalla anterior en el menú de

configuración.

39. Botón ENTER

Presione para establecer un ajuste.

40. Botones

{ /

Modo TV/VCR:

Presione para seleccionar un modo de ajuste en el

menú que aparece en la pantalla del televisor.

Presione también para seleccionar o establecer ajustes

en un menú en particular.

NOTA:

Antes de enchufar la antena a la toma ANT. de la

unidad, compruebe que la clavija no esté doblada.

Si esta doblada, póngala derecha como se muestra

en la ilustración, y luego conéctela en la toma

ANT. de la unidad.

Modo DVD:

Presione para seleccionar un ítem de menú.

41. Botón DISC MENU

Muestra menú del DVD.

42. Botón ZOOM

Clavija doblada

Amplía parte de la imagen reproducida de un DVD.

43. Botón MUTE

Cable

Suprime la salida de sonido. Presione de nuevo para

restablecer el sonido.

Clavija

(Necesita enderezarse)

(Clavija derecha)

44. Botón SLEEP

Utilice para ajustar el temporizador de dormir.

NOTA:

45. Toma ANT.

Para su seguridad y para evitar que se dañe

la unidad, desenchufe el cable de antena de la

toma ANT. antes de mover la unidad.

•

Conecte a una antena, sistema de televisión por cable o

sistema de satélite.

46. Cable de alimentación

Conecte a un toma de CA estándar (120 V, /60 Hz).

NOTA:

Antes de conectar el cable de alimentación de una

toma de CA estándar, retírelo del gancho para evitar

dañarlo.

•

47. Toma AUDIO OUT COAXIAL

Conecte solamente a la entrada digital de un

amplificador externo o decodificador (para audio de

DVD solamente).

–

Download from Www.Somanuals.com. All Manuals Search And Download.

CONEXIÓN A TOMAS DE

ENTRADA DELANTERAS

CONEXIÓN A UN DECODIFICADOR

DOLBY DIGITAL (para DVD)

Cuando vea un programa grabado en otra fuente

(videograbadora o videocámara), utilice las tomas de

entrada AUDIO/VIDEO de la parte delantera de la

unidad.

Si utiliza esta unidad para reproducir un disco DVD

grabado en formato de sonido envolvente Dolby

Digital de 5,1 canales, la unidad emitirá un flujo de

datos DOLBY DIGITAL desde su toma AUDIO

OUT COAXIAL. Si conecta la unidad a un

decodificador Dolby Digital, podrá disfrutar de una

tonalidad más convincente y real, con un sonido

envolvente potente y de alta calidad similar al de los

cines.

Conecte las tomas de salida de audio/vídeo de otra

fuente a las tomas AUDIO L/R y VIDEO de esta

unidad.

] hasta

Después, presione [SELECT] o [CH.

que aparezca “AUX” en la pantalla.

Utilice cables digitales coaxiales de audio

(disponibles en el comercio) para hacer las

conexiones de audio.

Consulte la figura 5 de la página 13

NOTA:

Cuando conecte una videograbadora monofónica

(otra fuente) a esta unidad, conecte la toma de

salida de audio de la videograbadora monofónica

(otra fuente) a la toma AUDIO L de esta unidad. El

audio saldrá igualmente por los canales izquierdo y

derecho.

•

Consulte la figura 7 de la página 14

NOTAS:

Asegúrese de apagar todos los componentes del

•

sistema antes de conectar otro componente.

Consulte los manuales de instrucciones de los

•

componentes que va a conectar a la unidad.

Si conecta un decodificador Dolby Digital, ajuste

•

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CON TOMAS

DE ENTRADA DIGITAL (para DVD)

Utilice un cable digital coaxial de audio (disponible en

el comercio) para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de

entrada digital, platina MD o platina DAT.

la función “DOLBY DIGITAL” a “BITSTREAM”

para salida de audio en el modo de configuración.

A menos que se haga la conexión a un

•

decodificador Dolby Digital, ajuste la función

“DOLBY DIGITAL” a “PCM” para salida de

audio en el modo de configuración. La

reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

Consulte la figura 6 de la página 13

NOTAS:

Fabricado bajo licencia de Dolby Laboratories.

“Dolby” y el símbolo de la doble D son marcas

comerciales de Dolby Laboratories.

• La fuente de audio de un disco grabado en formato

de sonido envolvente Dolby Digital de 5,1 canales

no se puede grabar como sonido digital mediante

• ^uAⁿs^aeg^pú^lare^tisⁿe^ad^Me ^Dap^oag^Dar^At^To^.dos los componentes del

• ^sC^iso^tn^es^mul^ate^anlo^tes^sm^da^en^cu^oaⁿle^es^ctd^ae^{r o}in^trs^otru^cocc^mio^pn^oeⁿs^end^te^e.los

• A^coj^mus^pte^onla^enf^tu^en^sc^qió^un^e“^vD^aO^aL^coBⁿY^ecD^taI^rG^aIT^laA^uLⁿ”^ida^a“^dP^.CM”

para salida de audio en el modo de configuración.

La reproducción en una unidad utilizando ajustes

incorrectos puede generar ruido y distorsión, y

también puede provocar daños a los altavoces.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

IDIOMA DEL MENÚ

SECCIÓN DE TV/VCR

TV/VCR

FUNCIONES Y AJUSTES

DE TV

1 Seleccione “LANGUAGE”

Presione [SETUP].

Presione [K / L] para apuntar a “LANGUAGE”.

PARA MIRAR UN PROGRAMA DE TV

TV/VCR

2 Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

1 Enchufe el cable eléctrico

Enchufe el cable eléctrico de la unidad en un

tomacorriente de CA del hogar.

NOTA:

Presione [ENTER] repetidamente para seleccionar

“ENGLISH” = inglés, “ESPAÑOL” o “FRANÇAIS”

= francés.

Si aparecen números en la esquina de la pantalla,

•

3 Salga del modo de idioma

Presione [SETUP] para salir del menú.

NOTAS:

presione [POWER] sin desenchufar el cable

eléctrico.

Esta función afecta sólo el idioma en el menú de la

pantalla y no la fuente de audio.

Si por alguna razón, el menú está en francés,

presione [SETUP], presione [K / L] para apuntar

al “LANGAGE [FRANÇAIS]” y presione

[ENTER] repetidamente para seleccionar el

idioma deseado y presione [SETUP].

•

2 Encienda la unidad

Presione [POWER] para encender la unidad.

•

3 Seleccione el número de canal

Presione [CH.

] o los botones numéricos para

seleccionar su número de canal deseado.

Nota para el uso de los botones numéricos:

¡Debe colocar un cero antes de los números de canal

de una sola cifra (por ejemplo: 02, 03, 04, etc.).

Cuando seleccione canales de cable de más de 99,

presione primero [+100] y después las dos últimas

cifras. (Ejemplo: para seleccionar el canal 125,

primero presione [+100] y después presione [2] y [5].)

AJUSTE DEL RELOJ

TV/VCR

AJUSTE MANUAL DEL RELOJ

Asegúrese ...

La unidad debe estar encendida.

En el siguiente ejemplo, el reloj debe estar en:

4 Ajuste el sonido

•

Presione [VOL.

] para ajustar el volumen.

Presione [MUTE] para silenciar instantáneamente el

sonido.

Presione nuevamente para recuperar el nivel de

sonido anterior.

FECHA

HORA DE AJUSTE

6 de mayo, 2005

5:40PM

NOTA:

1 Seleccione “AJUSTE RELOJ”

Presione [SETUP].

Presione [K / L] para selecciona “AJUSTE RELOJ”

y presione [ENTER].

Si presiona [CH.

] en el modo DVD, puede

•

cambiar los canales de TV. Incluso si apaga la

unidad en el modo DVD, cuando vuelva a

encender, volverá al modo TV/VCR.

PARA VER CANALES DE CABLE O

SATELITE

2 Seleccione “AJUSTE MANUAL RELOJ”

Presione [K / L] para seleccionar “AJUSTE

MANUAL RELOJ” y presione [ENTER].

Si la unidad está conectada a una caja de cable o

•

] para

caja de satélite, presione [CH.

seleccionar CH3 o CH4 de acuerdo con el ajuste

de canal de salida del dispositivo y seleccione el

canal deseado en el dispositivo.

3 Seleccione el mes

Presione [K / L] hasta que aparezca el mes deseado.

(Ejemplo: Mayo → “05”)

PARA VER UNA ENTRADA EXTERNA

Presione [B]. (O presione [s] para volver un paso.)

Cuando se conecta un equipo externo en las tomas

•

de entrada AUDIO/VIDEO frontales, presione

4 Seleccione el día

Presione [K / L] hasta que aparezca el día deseado.

(Ejemplo: 6º → “06”)

[SELECT] o [CH.

] repetidamente hasta que

aparezca “AUX” en la pantalla.

Presione [B].

–

Download from Www.Somanuals.com. All Manuals Search And Download.

GRABACIÓN

5 Seleccione el año

Presione [K / L] hasta que aparezca el año deseado.

(Ejemplo: “2005”)

GRABACIÓN NORMAL

Presione [B].

TV/VCR

SOLO puede ver el mismo programa que se está

grabando.

6 Seleccione la hora

Presione [K / L] hasta que aparezca la hora deseada.

(Ejemplo: “5”, “PM”)

1 Seleccione el canal a grabar

Presione [B].

Presione los botones numéricos o [CH.

NOTA:

7 Seleccione los minutos

Presione [K / L] hasta que aparezcan los minutos

deseados.

Si la unidad está conectada a una caja de cable o

caja de satélite, la unidad debe estar en CH3 o

CH4 y debe seleccionarse el canal a grabar en la

caja de cable o caja de satélite.

•

(Ejemplo: “40”)

2 Seleccione la velocidad de la cinta

8 Haga funcionar el reloj

Presione [SPEED] para seleccionar la velocidad de

Presione [SETUP].

cinta deseada (SP/SLP).

Aunque no aparezcan los segundos, empezará a

contar desde 00 cuando presione [SETUP]. Utilice

esta característica para sincronizar el reloj con la hora

real.

3 Empiece a grabar

Presione [RECORD].

4 Pare la grabación

Presione [STOP C].

–

Download from Www.Somanuals.com. All Manuals Search And Download.

REANUDACIÓN

SECCIÓN DE DVD

DVD-V CD

REPRODUCCIÓN BÁSICA

Durante la reproducción, presione [STOP C].

DVD-V CD

¡Aparecerá el mensaje de continuación en la pantalla

Para empezar

¡Conecte la alimentación del amplificador y otros

de TV.

componentes, si es necesario.

Presione [PLAY O], la reproducción continuará

desde el punto donde se paró la reproducción.

Presione [POWER].

¡La alimentación se conectará.

¡Para cancelar la continuación, presione dos veces

[STOP C].

¡La información de continuación permanece activada

incluso cuando apaga el interruptor principal.

Presione [A OPEN/CLOSE] para abrir la

bandeja de carga del disco.

Ponga el disco deseado en la bandeja, con

la etiqueta hacia arriba.

Presione [PLAY O].

¡La bandeja se cerrará automáticamente y la

reproducción comenzará desde el primer capítulo o

pista del disco.

¡La reproducción también empieza cerrando

manualmente la bandeja del disco o presionando

[A OPEN/CLOSE].

¡Si la reproducción no comienza automáticamente,

presione [PLAY O].

¡Cuando reproduzca un DVD que tenga grabado un

menú de títulos, el menú podrá aparecer en la

pantalla.

Presione [STOP C] para detener la

reproducción.

MENÚ DE DISCO

DVD-V

Presione [DISC MENU].

¡Aparecerá el menú principal de DVD.

¡Si no existe la función, puede aparecer el símbolo

en la pantalla de TV.

Si el menú de disco existe en el disco, aparecerán el

idioma de audio, opciones de subtítulo, capítulos para el

título y otras opciones para su selección.

Presione [K / L / s / B] para seleccionar

un ítem y presione [ENTER] para confirmar

la selección.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or

workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the

date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this

warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of

original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE

RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH

THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing

or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to

any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It

does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not

supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,

alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this

product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest Authorized Service Center or for general service procedure, please call or

write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429

http://www.SylvaniaConsumerElectronics.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Thailand

1EMN20670

T0153UD ★★★★★

Download from Www.Somanuals.com. All Manuals Search And Download.

Sherwood Stove EF 3 BAYI User Manual
Shindaiwa Trimmer 81642 User Manual
Shure Headphones SE420 User Manual
Sony Digital Camera AC UB10 User Manual
Sony DVD Player DVP CX777ES B User Manual
Sony Laptop FXA49 User Manual
Sony Projection Television KF 50SX100HK User Manual
Sony Speaker SA WX900 User Manual
Stamina Products Home Gym 50lb User Manual
Star Manufacturing Griddle 624TSPD User Manual