Sunrise Medical Mobility Aid P 222 User Manual

User

Quickie P-222

Instruction

Manual &

Warranty

Supplier:

This manual must be given to

the rider of this wheelchair.

Rider:

Before using this wheelchair

read this entire manual and

save for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

I . I n t r o d u c t i o n

SUNRISE LISTENS

Thank you for choosing a Quickie wheelchair. We want to hear your questions

or comments about this manual, the safety and reliability of your chair, and the ser-

vice you receive from your Sunrise supplier. Please feel free to write or call

us at the address and telephone number below:

Sunrise Medical

Mobility Products Division

Customer Service Department

7477 East Dry Creek Parkway

Longmont, Colorado 80503

(303) 218-4500 or (800) 333-4000

Be sure to return your warranty card, and let us know if you change your address. This

will allow us to keep you up to date with information about safety, new products and

options to increase your use and enjoyment of this wheelchair. If you lose your war-

ranty card, call or write and we will gladly send you a new one.

FOR ANSWERS TO YOUR QUESTIONS

Your authorized supplier knows your wheelchair best, and can answer most of your

questions about chair safety, use and maintenance. For future reference, fill in

the following:

Supplier: ______________________________________________________________________________

Address: _______________________________________________________________________________

______________________________________________________________________________________

Telephone:_____________________________________________________________________________

Serial #: _______________________________________ Date/Purchased: ________________________

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I I . T a b l e o f C o n t e n t s

IX. SET UP, ADJUSTMENT & USE................................................................................ 27

Notes................................................................................................................ 27

Tools You Will Need............................................................................................. 28

Check Out.......................................................................................................... 28

A. Power Drive Unit ............................................................................................ 29

B. Battery Removal............................................................................................. 29

C. Folding Backrest............................................................................................. 30

D. Footrests....................................................................................................... 30

E. Elevating Legrests (Optional) ........................................................................... 31

F. Remote Joystick Installation (Optional)............................................................. 31

G. To Adjust the Height of the Remote Joystick (Optional)....................................... 31

H. Remote Joystick Swing-Away Retractable Mount (Optional) .................................. 32

I. Dual-Post Height-Adjustable Armrests................................................................ 32

J. Single Post Height-Adjustable Armrests (Optional) .............................................. 32

K. Seat Depth.................................................................................................... 33

L. 10" Drive Wheel ............................................................................................. 34

M. Dynamic Stabilizer.......................................................................................... 34

MANUAL WHEELCHAIR CONVERSION KIT .............................................................. 35

A. Joystick ........................................................................................................ 35

B. Power Drive Unit ............................................................................................ 35

C. Wheel Locks .................................................................................................. 35

D. 24" Rear Wheels............................................................................................. 36

E. Anti-Tip Tubes ............................................................................................... 36

F. Installation of Axle Tube Assembly.................................................................... 36

G. Check-Out ..................................................................................................... 37

X. OPERATING GUIDE.............................................................................................. 38

A. Performance Control Settings ........................................................................... 38

B. Quickie QTRONIX Programmer Pad (Optional) ...................................................... 38

C. Thermal Roll-Back........................................................................................... 39

D. Circuit Breakers.............................................................................................. 39

E. Joystick Assembly........................................................................................... 40

F. Motor Locks................................................................................................... 42

XI. BATTERIES......................................................................................................... 43

A. Introduction.................................................................................................. 43

B. Battery Charger.............................................................................................. 44

C. Acid Burns..................................................................................................... 45

D. Connecting Batteries in Battery Compartment..................................................... 45

E. Charging Batteries.......................................................................................... 46

F. Disposing of Batteries..................................................................................... 47

XII. MAINTENANCE ................................................................................................... 48

A. Notes ........................................................................................................... 48

B. Cleaning ....................................................................................................... 48

C. Storage Tips .................................................................................................. 48

D. Battery Maintenance....................................................................................... 49

E. Pneumatic Tires.............................................................................................. 50

F. To Repair or Replace a Tire .............................................................................. 50

G. Ordering Parts................................................................................................ 51

H. Maintenance Chart.......................................................................................... 51

XIII. WIRING DIAGRAM.............................................................................................. 52

XIV. SUNRISE LIMITED WARRANTY.............................................................................. 53

I. INTRODUCTION ..................................................................................................

II. TABLE OF CONTENTS...........................................................................................

III. YOUR CHAIR AND ITS PARTS ...............................................................................

IV. NOTICE - READ BEFORE USE ................................................................................

V. EMI (ELECTROMAGNETIC INTERFERENCE) ..............................................................

A. What is EMI...................................................................................................

B. What Effect Can EMI Have ...............................................................................

C. Sources of EMI............................................................................................... 10

D. Distance From the Source ................................................................................ 10

E. Immunity Level.............................................................................................. 10

F. Report All Suspected EMI Incidents................................................................... 11

G. EMI From Chair .............................................................................................. 11

VI. GENERAL WARNINGS .......................................................................................... 12

A. Notice to Rider............................................................................................... 12

B. Notice to Attendants....................................................................................... 12

C. Weight Limit.................................................................................................. 13

D. Controller Settings.......................................................................................... 13

E. EMI.............................................................................................................. 13

F. Safety Checklist ............................................................................................. 13

G. Changes & Adjustments................................................................................... 14

H. When Seated in a Parked Wheelchair ................................................................. 14

I. Environmental Conditions ................................................................................ 14

J. Terrain.......................................................................................................... 15

K. Street Use ..................................................................................................... 15

L. Motor Vehicle Safety....................................................................................... 15

M. Center of Balance........................................................................................... 16

N. Transfers ....................................................................................................... 16

O. Reaching or Leaning....................................................................................... 17

P. Dressing or Changing Clothes ........................................................................... 17

Q. Obstacles ...................................................................................................... 18

R. Driving in Reverse .......................................................................................... 18

S. Ramps, Slopes & Sidehills................................................................................ 18

T. To Reduce the Risk of Falls, Tip-over or Loss of Control........................................ 19

U. Ramps at Home & Work................................................................................... 20

V. Wheelchair Lifts ............................................................................................. 20

W. Curbs & Single Steps....................................................................................... 21

X. Stairs ........................................................................................................... 21

Y. Escalators...................................................................................................... 21

VII. WARNINGS: COMPONENTS & OPTIONS................................................................... 22

A. Anti-Tip Levers .............................................................................................. 22

B. Armrests ....................................................................................................... 22

C. Batteries....................................................................................................... 22

D. Cushion & Sling Seats ..................................................................................... 22

E. Fasteners ...................................................................................................... 23

F. Footrests....................................................................................................... 23

G. Motor Lock.................................................................................................... 23

H. On/Off Switch................................................................................................ 23

I. Pneumatic Tires.............................................................................................. 24

J. Positioning Belts (Optional)............................................................................. 24

K. Push Handles................................................................................................. 24

L. Rear Wheel Locks (Optional) ............................................................................ 25

M. Seating Systems............................................................................................. 25

N. Upholstery Fabric ........................................................................................... 25

VIII. TIPS FOR ATTENDANTS........................................................................................ 26

A. To Climb a Curb or Single Step ......................................................................... 26

B. To Descend a Curb or Single Step...................................................................... 26

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I I I . Y o u r C h a i r a n d I t s P a r t s

Weight

115 lb. (52 kg) with swing-away

Footrest

Standard - Swing-away with compos-

footrests and armrests, without

batteries

ite footplates and heel loops, or two

piece locking.

Drive Wheels

Option - fixed tapered (80°) or fixed

straight (70°), elevating legrests,

angle-adjustable footplate, extended,

toe loops, extension tubes, solid one-

piece, two piece locking

12" x 4" Mag (260 mm)

Tire types: Standard - pneumatic

Option - 12" x 2"

Option - airless insert

Joystick

Casters

Standard - remote (right-hand or left-

hand mount)

Option - swing-away retractable,

USCM (Universal Specialty Control

Module)

Standard - 8" (200mm) pneumatic

Option - 8" (200mm) airless insert

8" (200mm) suspension

9" (225mm) pneumatic

9" (225mm)airless insert

Batteries

Armrests

(2 deep cycle batteries required to oper-

ate chair)

Option - 24 NF gel

Standard - dual post with standard or

full length pad

Option - dual post height-adjustable,

height-adjustable with standard or

full length pad

Battery Charger

Standard - dual mode (Lester)

Colors

Manual Wheelchair Conversion Kit

Standard - blue, black, red, midnight

purple, pearl pink, forest green,

burgundy, blue green, yellow, candy

teal, candy purple, toxic green, black

opal, blue velvet. Custom splatter col-

ors - purple chase.

Conversion Kit Axles

Option - quad-release axle nuts

Rear Wheels

Standard - Mag

Tire types: pneumatic, airless insert,

full-profile polyurethane, low-profile

polyurethane, Kevlar, high-pressure

clincher

Seat Frame Dimensions

Frame width: Standard - 16", 18"

(406, 457 mm)

Handrim

Option - 14", 15", 17", 19", 20", 22", 24"

(356, 381, 432, 482, 508, 558, 609mm)

Seat depth: 14"-20"(356 - 508 mm)

Seat height: Standard - 18" (458 mm),

option- 19" (508 mm), 20" (508 mm)

Seat sling: Standard - parapak,

Option - aluminum seat pan

Option-cushion: 2" (50mm)

Backrest Folding

Standard - aluminum

Q u i c k i e P - 2 2 2

Option - plastic-coated, long tabs

vertical or oblique projections

Wheel Locks

1. Armrest

2. Joystick

8. Push handle

9. Backrest hinge plate

Standard - Push-to-lock

Option - pull-to-lock

6" or 9" (150 mm or 230 mm) exten-

sion handles

3. Seat cushion (optional)

4. Fixed front hanger

5. Caster tire

6. Two-piece, locking, flip-up foot-

plate

10. Quick-connect lever

11. Seat frame

12. Dynamic stabilizer

13. Drive wheels

Standard - 15.5" (393 mm)

Option - 17.5", 19.5"

(445 mm, 495 mm)

All features may not be available with some

chair setups or in conjunction with another

chair feature. Please consult your supplier for

more information. Your authorized supplier

can also provide you with more information

on accessories.

14. Base Frame

7. Backrest

Caster Fork

Standard - fixed

Option - Suspension (8" tire only)

The Quickie P-222 is a class B wheelchair as

defined in EN 12184

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I V . N o t i c e – R e a d B e f o r e U s e

V . E M I ( E l e c t r o m a g n e t i c I n t e r f e r e n c e )

A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS

Sunrise provides a choice of many power wheelchair styles, sizes and adjustments to

meet the needs of the rider. However, final selection of a wheelchair rests solely with

you and your health care professional. Choosing the best chair for you depends on

such things as:

Heed all warnings to reduce the risk of unintended brake release or chair

movement:

1.Beware of the danger from hand-held transceivers. Never turn on or use a

hand-held transceiver while power to your chair is on. Use extra care if you

believe that such a device may be in use near your chair.

2.Be aware of nearby radio or TV stations, and avoid coming close to them.

3.If unintended movement occurs, turn your chair off as soon as it is safe to

do so.

1. Your size, disability, strength, balance and coordination.

2. Your intended use, and your level of activity.

3. The types of hazards you must overcome in daily use (in areas where you are

likely to use your chair).

4. The need for options for your safety and comfort (such as positioning belts

or special seat systems).

A. WHAT IS EMI?

B. ADJUST CHAIR TO YOUR ABILITY

1. EMI means: electromagnetic (EM) interference (I). EMI comes from radio wave

sources such as radio transmitters and transceivers. (A “transceiver” is a device

that both sends and receives radio wave signals).

You need to work with your doctor, nurse or therapist, and your supplier, to fit this

chair and adjust the controller settings for your level of function and ability.

2. There are a number of sources of intense EMI in your daily environment.

Some of these are obvious and easy to avoid. Others are not, and you may not

be able to avoid them.

3. Powered wheelchairs may be susceptible to electromagnetic interference (EMI)

emitted from sources such as radio stations, TV stations, amateur radio (HAM)

transmitters, two way radios, and cellular phones.

C. REVIEW THIS MANUAL OFTEN

Before using this chair you, and each person who may assist you, should read this

entire Manual and make sure to follow all instructions. Review the warnings often,

until they are second nature to you.

D. WARNINGS

4. EMI can also be produced by conducted sources or electro-static discharge (ESD).

The word “WARNING” refers to a hazard or unsafe practice that may cause severe injury or

death to you or to other persons. The “Warnings” are in four main sections, as follows:

B. WHAT EFFECT CAN EMI HAVE?

1. V — EMI

1. EMI can cause your chair, without warning, to:

•Release its brakes

Here you will learn about electromagnetic interference and how it can affect your

chair.

•Move by itself

2. VI — GENERAL WARNINGS

•Move in unintended directions

Here you will find a safety checklist and a summary of risks you need to be

aware of before you ride this chair.

3. VII — WARNINGS — COMPONENTS & OPTIONS

Here you will learn about your chair. Consult your supplier and your health care

professional to help you choose the best set-up and options for your safety.

4. XI — BATTERIES

If any of these occurs, it could result in severe injury to you or others.

2. EMI can damage the control system of your chair. This could create a safety

hazard, and lead to costly repairs.

Here you will learn about battery and charger safety, and how to avoid injury.

NOTE– Where they apply, you will also find “Warnings” in other sections of this

Manual.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V . E M I ( E l e c t r o m a g n e t i c I n t e r f e r e n c e )

4. The following specialty input devices have an unknown effect on the immunity level

because they have not been tested with the P-222 and QTRONIX control system:

C. SOURCES OF EMI

The sources of EMI fall into three broad types:

1. Hand-Held Transceivers:

•Breath Control

• Proportional Head Control

• Proportional Mini-Joystick/Chin Control

• Buddy Button

• Micro Light

• Star Board

• Wafer Board

• Penta Switch

• Plate Switch

• Soft Switch

•Tri-Switch Head Array

•Heavy Duty Switched Joystick

•Treadle Switch

The antenna is usually mounted directly on the unit. These include:

• Citizens band (CB) radios

• “Walkie-talkies”

• Security, fire and police radios

• Cellular phones

• Lap-top computers with phone or fax

• Other personal communication devices

•Ribbon Switch

•Proximity Head Array

•Zero Touch Switch

•4-Zero Touch Switch

•5-Zero Touch Switch

•Disc Switch

NOTE– These devices can transmit signals while they are on, even if not in use.

• Grasp Switch

•Wobble Switch

2. Medium-Range Mobile Transceivers:

These include two-way radios used in police cars, fire trucks, ambulances and taxi

cabs. The antenna is usually mounted on the outside of the vehicle.

Individuals with physical limitations requiring the use of a specialty control

input device known not to be immune to 20V/m, or not known, should exer-

cise extra care around known sources of EMI.

3. Long-Range Transceivers:

These include commercial radio and TV broadcast antenna towers and

amateur (HAM) radios. NOTE– The following are not likely to cause EMI problems: Lap-

top computers (without phone or fax), Cordless phones, TV sets or AM/FM radios, CD or

tape players.

There is no way to know the effect on EMI if you add accessories or modify

this chair. Any change to your chair may increase the risk of EMI. Parts not

specifically tested or parts from other suppliers have unknown EMI properties.

D. DISTANCE FROM THE SOURCE

F. REPORT ALL SUSPECTED EMI INCIDENTS

EM energy rapidly becomes more intense as you get closer to the source. For this rea-

son, EMI from hand-held devices is of special concern. (See C.1 above) A person

using one of these devices can bring high levels of EM energy very close to your chair

without you knowing it.

You should promptly report any unintended movement or brake release.

Be sure to indicate whether there was a radio wave source near your chair

at the time. Contact:

E. IMMUNITY LEVEL

Sunrise Medical, Customer Service Department at (800) 333-4000.

1. The level of EM is measured in volts per meter (V/m). Every power wheelchair

can resist EMI up to a certain level. This is called its “immunity level”.

2. The higher the immunity level, the less the risk of EMI. It is believed that a

20 V/m immunity level will protect the power wheelchair user from the more

common sources of radio waves.

3. The configuration tested and found to be immune to at least 20 V/m is:

Quickie P-222 power wheelchair with a right-hand mounted QTRONIX remote joy-

stick system, 18" seat width, 18" seat depth, dual post height adjustable arm-

rests, fixed tapered legrests with one piece solid footplate, and Gp 24 gel cell

batteries.

G. EMI FROM CHAIR

The chair itself can disturb the performance of electromagnetic fields such as emitted

by alarm systems of shops.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G e n e r a l W a r n i n g s

V I .

G e n e r a l W a r n i n g s

C. WEIGHT LIMIT

Heed all warnings in this section. If you fail to do so a fall, tip-over or loss

of control may occur and cause severe injury to your or others.

1. The rider plus items carried should never exceed a total weight of 250 pounds

(113 kilograms) or 350 pounds (159 kg) for heavy duty option.

2. Never use this chair for weight training if the total weight (rider plus

additional weights) exceeds 250 (113 kg) pounds or 350 pounds (159 kg) for

heavy duty option.

3. Exceeding the weight limit is likely to damage the seat, frame, or fasteners, and

may cause severe injury to you or others from chair failure.

4. Exceeding the weight limit will void the warranty.

A. NOTICE TO RIDER

1. Before using this chair, you should be trained in its safe use by your health care

professional.

2. Every wheelchair is different. Take the time to learn the feel of this chair before

you begin riding.

3. Be aware that you must develop your own methods for the safe use of this chair,

that are best suited to your level of function and ability.

4. Have someone help you practice bending, reaching and transfers until you learn

how to do them safely.

D. CONTROLLER SETTINGS

Be aware that you may need to adjust the controller settings of your chair to reduce

the risk of a collision, fall or tip-over.

5. Never try a new maneuver on your own unless you are sure it is safe.

6. Get to know the areas where you plan to use your chair. Look for hazards

and learn how to avoid them.

1. Check and adjust the settings every six to twelve months (or more often, if needed).

2. Consult your supplier to adjust the control settings immediately if you notice

any change in your ability to:

•Control the joystick

•Hold your torso erect

B. NOTICE TO ATTENDANTS

•Avoid running into objects.

Make sure you heed all warnings and follow all instructions in each section of this

manual. (Be aware that warnings that apply to the rider also apply to you).

E. EMI

NOTES–

Read Section V to learn about EMI. To reduce the risk of unintended brake release or

chair movement:

1. You need to work with the rider, and the rider’s doctor, nurse or therapist, to

develop safe methods best suited to your abilities and those of the rider.

2. To manually push the chair you must release the motor locks.

•Make sure you have full control over the chair when you release the

motor locks. When you do so the chair will not have brakes.

3. Propel this chair by the push handles only. They provide secure points for

you to hold the rear of the chair to prevent a fall or tip-over.

•Check to make sure push handle grips will not rotate or slip off.

Helping The Rider Overcome An Obstacle:

1. Never turn on or use a hand-held transceiver while power to your chair is on.

Use extra care if you believe that such a device may be in use near you chair.

2. Be aware of nearby radio or TV stations, and avoid coming close to them.

3. If unintended movement or brake release occurs, turn your chair off as soon

as it is safe.

F. SAFETY CHECK-LIST

Before each use of this chair:

1. To prevent injury to your back, use good posture and proper body mechanics.

When you lift or support the rider or tilt the chair, bend your knees slightly

and keep your back as upright and straight as you can.

2. Before each maneuver, tell the rider what you plan to do, and explain what you

expect the rider to do. This will put the rider at ease and reduce the risk of an

accident.

1. Make sure the chair operates smoothly. Check for noise, vibration, or a change in

ease of use. (They may indicate low tire pressure, loose fasteners, or damage to

your chair).

•If you detect a problem, make sure to repair or adjust the chair. Your supplier

can help you find and correct the problem.

2. Make sure batteries are charged. Green lights on charge indicator will light up

when charge is full. Yellow lights indicate battery charge level is getting low.

Red lights indicate batteries are in immediate need of charging.

3. Go straight up and straight down a curb or stair. If you turn, or climb or

descend at an angle, a fall or tip-over is likely.

4. Remind the rider to lean back when you tilt the chair backward.

5. Lower the chair slowly. Do not let the chair drop to the pavement or ground.

Doing so may damage the chair or injure the rider.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G e n e r a l W a r n i n g s

V I .

G e n e r a l W a r n i n g s

3. When not in use, keep your chair in a clean, dry place.

G. CHANGES & ADJUSTMENTS

Never use non-Quickie parts or make a changes to your chair unless authorized by

Sunrise. (Doing so will void the Warranty and may create a safety hazard).

1. If you modify or adjust this chair it may increase the risk of a fall or tip-over.

2. Modifications unauthorized by Sunrise constitutes remanufacturing of the wheel-

chair. This voids the warranty. The rider then assumes all future liability

for the wheelchair.

Extra caution should be used when employing the disc switch or the proximi-

ty head array as control devices. These two devices are susceptible to mal-

function when wet.

J. TERRAIN

1. This chair is designed for use on firm, even surfaces such as concrete, asphalt

and indoor flooring.

H. WHEN SEATED IN A PARKED WHEELCHAIR

2. Do not operate your chair in sand, loose soil or over rough terrain. Doing so may

damage wheels, bearings, axles or motors, or loosen fasteners.

1. Always turn off all power to your chair when you are parked, even for a moment.

This will prevent:

K. STREET USE

•Accidental movement from contact with the joystick by you or others.

•Unintended brake release or movement from EMI sources. (See Section V)

2. Make sure that persons who help you (for example, store clerks) are aware

of the joystick and do not touch it. If they do, your chair may move suddenly

when you do not expect it.

In most states, power chairs are not legal for use on public roads. Be alert to the dan-

ger of motor vehicles on roads or in parking lots.

1. At night, or when it is hard to see, use reflective tape on your chair and clothing.

2. It may be hard for drivers to see you. Make eye contact with drivers before you

proceed. When in doubt, yield until you are sure it is safe.

I. ENVIRONMENTAL CONDITIONS

L. MOTOR VEHICLE SAFETY

Your chair is not designed for use in a heavy rain storm, or in snowy or icy conditions.

1. Contact with water or excessive moisture can cause an electrical

malfunction. The frame, motors and other chair parts are not water-tight

and may rust or corrode from the inside. To avoid a chair failure:

•Minimize exposure of your chair to a rain storm or very wet conditions.

•Never take your chair into a shower, tub, pool or sauna.

•Do not use your chair in fresh or salt water (such as at the edge of a stream,

lake, or ocean).

To date, the U.S. Department of Transportation has not approved any tie down system

for transporting a wheelchair in a motor vehicle.

1. Never sit in this chair while in a moving vehicle. In an accident or sudden stop

you may be thrown from the chair.

•Wheelchair belts are designed to position the rider only and will not pro-

tect you in an accident; further injury may result from the belts.

2. Always move to an approved vehicle seat. You must be secured with proper

motor vehicle restraints.

•Make sure battery covers are secure.

•Replace joystick boot if it becomes torn or cracked.

•Make sure all electrical connections are secure.

3. Never transport this chair in the front seat of a vehicle. It may shift and

interfere with the driver.

4. Always secure this chair so that it cannot roll or shift.

•Dry the chair as soon as you can if it gets wet, or if you use water to clean it.

2. Proceed slowly and use extra care if you must operate your chair on a wet

or slick surface.

•Do so only if you are sure it is safe.

•Stop if one or both main wheels lose traction. If this occurs, you may lose

control of your chair or fall.

•Never operate your chair on a slope or ramp if there is snow, ice, water

or oil film present.

•When in doubt, have someone help you.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G e n e r a l W a r n i n g s

V I .

G e n e r a l W a r n i n g s

O. REACHING OR LEANING

M. CENTER OF BALANCE

The point where this chair will tip forward, back, or to the side depends on its center

of balance and stability.

Reaching or leaning affects the center of balance of your chair. If done improperly, a fall

or tip-over is likely. When in doubt, ask for help or use a device to extend your reach.

The Center Of Balance Is Affected By:

To Reduce the Risk of injury and/or Damage to the Chair:

1. Never reach or lean if you must shift your weight sideways or rise up off the seat.

2. Never reach or lean if you must move forward in your seat to do so. Always keep

your buttocks in contact with the backrest.

1. The seat height and seat angle.

2. A change in your body position, posture or weight distribution.

3. Using this chair on a ramp or slope.

4. The use of a back pack or other options, and the amount of added weight.

5. Drive wheel positioning.

3. Never reach with both hands (you may not be able to catch yourself to prevent

a fall if you lose your balance).

To Reduce The Risk Of A Fall Or Tip-Over:

4. Never try to pick up an object from the floor by reaching down between your knees.

5. Never put pressure on the footrests while reaching. This may cause the chair to

tip if you lean too far.

6. Never reach or lean over the top of the seat back. This may damage the backrest

and cause you to fall.

1. Consult your supplier for information on modifications authorized by Sunrise

before you modify or adjust this chair.

NOTE– You may need to make additional changes to correct the center of balance.

2. Use extreme care until you know the balance points of this chair and how to

avoid a fall or tip-over.

IF YOU MUST REACH OR LEAN; DO SO AT YOUR OWN RISK.

N. TRANSFERS

Remember to:

1. Move your chair as close as you can to the object you wish to reach.

2. Rotate the front casters until they are as far forward as possible. This makes the

chair more stable.

It is dangerous to transfer on your own. It requires good balance and agility.

Be aware that there is a point during every transfer when the wheelchair seat is not

below you. To avoid a fall:

NOTE– To do this: Move your chair past the object you want to reach, then back up

1. Always turn off power before you transfer to or from your chair. If you fail to

do so you may touch the joystick and cause your chair to move when you do

not expect it.

2. Make sure motor locks are engaged. This keeps the chair from moving when

you transfer.

3. Work with your health care professional to learn safe methods.

•Learn how to position your body and how to support yourself during a transfer.

•Have someone help you until you are sure you can do a safe transfer

on your own.

4. Move your chair as close as you can to the seat you are transferring to.

If possible, use a transfer board.

alongside it. Backing up will rotate the casters forward.

3. Turn off all power to your chair. If you fail to do so, you may touch the joystick

and cause your chair to move when you do not expect it.

4. Firmly grasp a rear wheel or an armrest with one hand. This will help to

prevent a fall if the chair tips.

P. DRESSING OR CHANGING CLOTHES

Be aware that your weight will shift if you dress or change clothes while seated in this

chair. To make the chair more stable, rotate the front casters until they are forward.

5. Rotate the front casters until they are as far forward as possible.

6. Be careful of the footrests. If you can, remove or swing them out of the way.

•Never stand on footrests when you transfer. Doing so may damage them or

cause your chair to tip.

•Make sure your feet do not “hang up” or get caught in the space between the

footrests.

7. Make sure armrests do not interfere.

8. Transfer as far back onto the seat surface as you can. This will reduce the risk

that you will miss the seat or fall.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G e n e r a l W a r n i n g s

V I .

G e n e r a l W a r n i n g s

T. TO REDUCE THE RISK OF A FALL, TIP-OVER OR

LOSS OF CONTROL:

Q. OBSTACLES

Obstacles you may have to overcome in daily use include door thresholds, lifts, ramps

and hazards such as potholes and broken pavement. These can damage your chair and

may cause a fall, tip-over or loss of control.

1. Never use your chair on a slope unless you are

sure you can do so without losing traction.

2. Always go as straight up and as straight down as

you can.

•Do not “cut the corner” on a slope or ramp.

•Do not turn or change direction on a slope.

3. Always stay in the center of the ramp. Make sure

ramp is wide enough that you are not at risk

that a wheel may roll off the side.

1. Be aware that thresholds are very dangerous. (Even a small change in height

may stop a caster wheel and cause your chair to tip). You may need to:

•Remove or cover threshold strips between rooms.

•Install a ramp at entry or exit doors.

Figure 1

2. Keep your eyes moving when you ride; scan the area well ahead of your chair.

3. Make sure the floor areas where you use this chair are level and free of obstacles.

4. To help correct your center of balance:

4. Lean or press your body uphill. This will help

adjust for a change in the center of balance

caused by the slope. (Fig. 1)

5. Keep your chair moving at a slow, steady speed.

Keep control over the chair at all times.

•On a descent, do not let your chair accelerate

beyond its normal speed.

•Lean your upper body forward slightly as you go up over an obstacle.

•Press your upper body backward as you go down from a higher to a lower level.

R. DRIVING IN REVERSE

Use extra care when you drive your chair in reverse. You may lose control or fall if one

of the rear wheels hits an object.

1. Operate your chair slowly and at an even speed.

2. Stop often and check to make sure your path is clear of obstacles.

•If the chair picks up speed, center the joystick

to slow down or stop.

NOTE– The solid state controller of your chair has a

logic system that will help control your speed

when driving on a slope or up hill.

S. RAMPS, SLOPES & SIDEHILLS

The center of balance of your chair changes when you are on a slope.

•If you stop, re-start slowly.

6. Never use rear wheel locks to try to slow or stop

your chair. This is likely to cause the chair to

veer out of control.

NOTE– “Slope” includes a ramp or sidehill. Your chair is less stable when it is at an

angle. Never use this chair on a slope unless your are sure it is safe. When in

doubt, have someone help you.

Beware Of:

1. Steep slopes. Do Not use this chair on a slope steeper than 10%. (A 10% slope

means: One foot in elevation for every ten feet of slope length).

2. Wet or slippery surfaces (such as when ice, snow, water or oil film is present). A

loss of traction may cause a fall or tip-over.

3. A change in grade on a slope (or a lip, bump or depression). These may cause a

fall or tip-over.

4. A drop-off at the bottom of a slope. (A drop-off of as small as 3/4 inch (12 mm)

can stop a front caster and cause the chair to tip forward).

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I .

G e n e r a l W a r n i n g s

V I .

G e n e r a l W a r n i n g s

W. CURBS & SINGLE STEPS

U. RAMPS AT HOME & WORK

1. Your chair is not designed to drive up or down a curb or step more than two (2)

inches (5 cm) high. Doing so may:

•Result in a fall or tip-over.

•Damage the frame, wheels, axles or other chair parts, or loosen fasteners.

2. To prevent a fall or tip-over, use wheelchair access ramps or have

someone help you.

3. If you must climb or descend a curb or step alone do so at your own risk and

use extreme care.

•Go as straight up or straight down as you can. Never turn or climb or descend

at an angle as a fall or tip-over is likely.

•Proceed slowly, at a steady speed.

4. Make sure that persons who assist you review the “Tips For Attendants”

and heed all warnings.

Make sure ramps meet all Building Codes for your area.

1. For your safety, have a licensed contractor build or remodel ramp to meet

all standards.

2. NOTE– The proper design will vary, depending on such things as: the length and

height of the ramp; the need for an intermediate platform; landing size; doors,

and the direction of swing, and; whether the ramp includes a turn or angle.

At A Minimum:

1. Open sides of ramp must have side rails to prevent your chair from going over

the edge.

2. Slope must not be steeper than one inch in height for every one foot of slope

length (approximately 5º).

3. Ramp surface must be even, and have a non-skid surface.

4. You may need to add a section at the top or bottom to avoid a lip or drop-off.

5. Ramp must be sturdy. Add bracing if needed, so ramp does not “bow” when you

ride on it.

X. STAIRS

Never use this chair to go up or down stairs, even with an attendant. Doing

so is likely to cause a fall or tip-over.

V. WHEELCHAIR LIFTS

Y. ESCALATORS

Wheelchair lifts are used in vans, buses, and buildings to help you move from one

level to another.

Never take this chair on an escalator, even with an attendant. Doing so is

likely to cause a fall or tip-over.

1. Always turn off all power to your chair when you are on a lift. If you fail to do

so, you may touch the joystick by accident and cause your chair to drive off the

platform. (Be aware that a “roll-stop” at the end of the platform may not pre-

vent this).

2. Make sure there is not a lip or drop-off at the top or bottom of the platform.

These may cause a fall or tip-over. When in doubt, have someone help you.

3. Always position the rider securely in the chair to help prevent falls while on a

lift.

4. Avoid moving forward if a wheel is “hung up” on the lip of the ramp. Backup,

reposition the caster for a more direct approach. And slowly try again.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I .

W a r n i n g s : C o m p o n e n t s

O p t i o n s

V I I .

W a r n i n g s : C o m p o n e n t s

O p t i o n s

E. FASTENERS

Note: If you use parts or make changes not authorized by Sunrise it may cre-

ate a safety hazard and will void the Warranty.

Many of the screws, bolts and nuts on this chair are special high-strength fasteners.

Use of improper fasteners may cause your chair to fail.

A. ANTI-TIP LEVERS

1. Only use fasteners provided by Sunrise.

2. If fasteners become loose, tighten them as soon as you can.

3. Over- or under-tightened fasteners may fail or cause damage to chair parts.

•See Section IX, “Set-Up, Adjustment & Use”, for proper torque settings.

Never remove or alter anti-tip levers. They help keep your chair from tipping

over backward in normal use. Make sure rubber rollers are in good condition.

B. ARMRESTS

F. FOOTRESTS

1. At the lowest point, footrests should be at least 2 1/2 inches (65 mm) off the

ground. If set too LOW, they may “hang up” on obstacles you can expect to find

in normal use. This may cause the chair to stop suddenly and tip forward.

2. To avoid a trip or fall when you transfer:

Armrests detach and will not bear the weight of this chair.

1. Never lift this chair by its armrests. They may come loose or break.

2. Lift this chair only by non-detachable parts of the main frame.

C. BATTERIES

•Make sure your feet do not “hang up” or get caught in the space between the

footrests.

•Avoid putting weight on the footrests, as the chair may tip forward.

•Remove or swing the footrests out of the way, if possible.

3. Never lift this chair by the footrests. Footrests detach and will not bear

the weight of this chair. Lift this chair only by non-detachable parts of the

main frame.

1. Only deep cycle sealed case construction batteries should be used in

this device.

2. To prevent an acid spill, always keep batteries upright (wet cell batteries).

3. Never smoke or hold an open flame near batteries. They are a known

explosion hazard.

G. MOTOR LOCKS

4. Always wear rubber gloves and safety glasses when you handle batteries.

5. Read all of section XI. Batteries before attempting to change, or charge batteries.

D. CUSHIONS & SLING SEATS

1. Do not engage or disengage motor locks unless power to the chair is off.

2. With the brakes released, the chair will not operate and the battery charge indi-

cator will flash 9 bars rapidly (if power to the chair is on).

3. Be aware that the chair will not have brakes when motor locks are in the

free-wheel position.

1. Quickie sling seats, standard foam cushions, and other body supports, are not

designed for the relief of pressure.

2. If you suffer from pressure sores, or if you are at risk that they will occur, you

may need a special seat system or a device to control your posture.

•Consult your doctor, nurse or therapist to find out if you need such a device for

your well-being.

4. Make sure that the person pushing the chair has full control when motor

locks are disengaged.

H. ON/OFF SWITCH

1. Never use the ON/OFF switch to stop the chair except in an emergency.

This will result in an abrupt stop, and may cause you to fall.

2. To slow your chair to a stop, return the joystick to neutral.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I .

W a r n i n g s : C o m p o n e n t s

O p t i o n s

V I I .

W a r n i n g s : C o m p o n e n t s

O p t i o n s

L. REAR WHEEL LOCKS (OPTIONAL)

I. PNEUMATIC TIRES

If you request them, we will install rear wheel locks at Sunrise.

Proper inflation extends the life of your tires and makes your chair easier to use.

1. Rear wheel locks are not designed to slow or stop a moving wheelchair.

Never apply them when your chair is moving. Doing so may cause you to veer

out of control.

•Use wheel locks only to keep the rear wheels from rolling when your chair is at

a complete stop.

1. Do not use this chair if any of the tires are under- or over-inflated. Check

weekly for proper inflation level, as listed on the tire sidewall.

2. Low pressure in a tire may cause the chair to veer to one side and result in a

loss of control.

3. An over-inflated tire may burst.

2. Low pressure in a rear tire may cause the wheel lock on that side to slip and

may allow the wheel to turn when you do not expect it.

3. Make sure lock arms embed in tires at least 3/8 inch (9.5 mm) when locked. If

you fail to do so, the locks may not work.

4. Never use a gas station air pump to inflate a tire. Such pumps provide air at

high volume, and could cause the tire to burst. To prevent tire damage:

•Use a hand pump (or a low volume air pump) to inflate tires.

•Use a tire gauge to check pressure.

5. Driving over sharp objects may cause damage to pneumatic tires and tubes.

M. SEATING SYSTEMS

J. POSITIONING BELTS (OPTIONAL)

1. Use of a seating system not approved by Sunrise may alter the center of

balance of this chair. This may cause a fall or tip-over.

2. Never change the seating system of your chair unless you consult your

supplier first.

Use a positioning belt only to help support your posture. Improper use of such belts

may cause severe injury or death.

1. Make sure you are not at risk to slide down in the wheelchair seat. If this occurs,

you may suffer chest compression or suffocate due to pressure from the belt.

2. A pelvic wedge or a similar device can help keep you from sliding down in the

seat. Consult your health care professional to find out if you need such a device.

3. The belt must be snug, but must not be so tight that it interferes with breath-

ing. You should be able to slide your open hand, flat, between the belt and your

stomach.

4. Make sure you can easily remove the belt in an emergency.

5. Never use a positioning belt:

•In place of a motor vehicle seat belt. In an accident or sudden stop you may

be thrown from the chair. A positioning belt will not prevent this, and further

injury may result from the belt.

N. UPHOLSTERY FABRIC

1. Replace worn or torn fabric of seat sling and seat back as soon as you can.

If you fail to do so, the seat may fail and cause you to fall. Worn fabrics may

increase the potential for a fire hazard.

2. Sling fabric will deteriorate with age and use. Look for fraying, thin spots, or

stretching of fabric at rivet holes. Replace fabric as required.

3. “Dropping down” into sling seat will weaken fabric and result in the need to

inspect and replace sling on a more frequent basis.

4. Be aware that washing may reduce flame retardation of the fabric.

•As a restraint. A restraint requires a doctor’s order.

•On a rider who is comatose or agitated.

K. PUSH HANDLES

1. Push handles provide secure points for an attendant to propel and control the

chair. This helps to prevent a fall or tip-over.

2. Check to make sure push handle grips will not rotate or slip off.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

V I I I . T i p s f o r A t t e n d a n t s

I X . S e t - U p , A d j u s t m e n t

U s e

NOTES

1. Work Surface For Set-Up:

1.Persons who help a rider do one of the following tasks should review and

heed the warnings “Notice to Attendants” and all warnings in this Manual

for that task.

Use a flat surface, such as a table, to assemble, adjust and check your chair.

This makes the steps easier and helps ensure a correct set-up.

2.The “Tips” that follow are suggestions only. Be aware that you will need to

learn safe methods best suited to the rider and to your abilities. Consult

your health care professional for instructions.

2. Fasteners:

• Many of the screws and bolts on this chair are special high-strength fasteners

and may have special coatings.

• Many nuts are of the Nylock type. They have a plastic insert to help prevent

loosening.

A. TO CLIMB A CURB OR SINGLE STEP

• Only use screws, bolts and nuts provided by Sunrise.

The following is one way to safely help a rider climb a curb or single step going forward:

1.Use of improper fasteners may cause the chair to fail.

2.Over- or under-tightened fasteners may fail or cause damage to chair parts.

3.If bolts or screws become loose,tighten them as soon as you can. Loose

bolts or screws can cause damage to other chair parts causing them to fail.

3. Washers & Spacers:

1. Stay behind the chair.

2. Face the curb and tilt the chair up on the rear wheels so that the front casters

clear the curb or step.

3. Move forward, placing the front casters on the upper level as soon as you are

sure they are past the edge.

• Note the position of washers and spacers before disassembly.

• To avoid damage to the frame, replace all washers and spacers when you

reassemble parts.

4. Continue forward until the rear wheels contact the face of the curb or step.

Lift and roll the rear wheels to the upper level.

B. TO DESCEND A CURB OR SINGLE STEP

4. Torque Settings:

• A torque setting is the optimal tightening for a particular fastener. Use a torque

wrench that measures inch-pounds to secure screws, nuts and bolts on this

chair.

The following is one way to safely help a rider descend a curb or single step going

backward:

NOTE– Unless otherwise noted, use a torque setting of 120 inch-pounds (13.5 N.m) for

1. Stay at the rear of the chair.

2. Several feet before your reach the edge of the curb or step, turn the chair

around and pull it backward.

all fasteners.

3. Proceed carefully. Look over your shoulder and carefully step back until you

are off the curb or stair and standing on the lower level.

4. Pull the chair toward you until the rear wheels reach the edge of the curb or

step. Then allow the rear wheels to slowly roll down onto the lower level.

5. When the rear wheels are safely on the lower level, tilt the chair back to its

balance point. This will lift the front casters off the curb or step.

6. Keep the chair in balance and take small steps backward. Be sure to look where

you are going. Turn the chair around and gently lower front casters

to the ground.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S e t - U p , A d j u s t m e n t

U s e

I X . S e t - U p , A d j u s t m e n t

U s e

A. POWER DRIVE UNIT

TOOLS YOU WILL NEED

1. Basic Tool Kit:

Wheelchair and Power Drive Attachment

a. Position seat and main frame over power drive unit.

b. Align quick-connect blocks (A) with binding

socket (B) located on power drive unit.

c. Ensure frame is properly located on power drive

unit and the controller cable is clear.

d. Press levers (C) down until locked.

e. Lever force required can be adjusted by adjusting

screw.

To set-up, adjust and maintain your chair you will need the following tools:

• 7/16" box and open-end wrench

• 1/2" box and open-end wrench

• 3/4" box and open-end wrench

• 5/32" Allen wrench

• 3/16" Allen wrench

• 1/8" Allen wrench

• Phillips screwdriver #2

• Custom axle wrench (or a 1/2" open-end wrench)

Always secure levers before operating chair. If

the chair fails to operate and the battery

charge indicator flashes 9 bars, check both

quick-connect levers for securement. Then cycle

the on/off switch.

You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you need from a

hardware store.

2. Torque Wrench:

If you plan to adjust and maintain this chair yourself, Quickie recommends that you

use a torque wrench.

B. BATTERY REMOVAL

NOTE– The wrench must measure inch-pounds (N.m). You can buy a torque wrench and

To remove the batteries for transporting or servicing:

proper sockets from a hardware store.

Remove Batteries

CHECK-OUT

a. Remove seat and main frame from power drive

unit using quick-release levers shown above. (C)

b. Remove battery compartment lid by releasing the

two (2) quarter turn fasteners (D).

c. Prevent the power drive unit from tipping for-

ward by placing a solid object underneath the

front of the power drive unit.

Be sure this chair performs to your chosen operational settings. If it does not, turn

the chair off immediately and reprogram with the Quickie QTRONIX Programmer. if you

do not own a Quickie QTRONIX Programmer have your supplier reprogram your wheel-

chair as needed. Or, you can order a Quickie QTRONIX Programmer for your own use

from your supplier.

NOTE– Repeat this procedure until the chair performs to your specifications

d. Lift battery compartment lid (E) off of power

drive unit.

e. Disconnect battery leads from power harness.

f. Lift rear most battery out using the battery

straps (F).

g. Pull the front battery rearward, disconnect it,

and remove it using the battery straps.

When properly set-up, this chair will operate smoothly. Check to see that all

components work properly. If you detect a problem, be sure to correct it

before use.

Batteries may weigh up to 55 lbs. (25 kg).

Care must be taken to avoid injury when lifting.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S e t - U p , A d j u s t m e n t

U s e

I X . S e t - U p , A d j u s t m e n t

U s e

ELEVATING LEGREST (OPTIONAL)

C. FOLDING BACKREST

1. Installation

Quickie P-222 wheelchairs are shipped with backrest in

folded position.

To install or remove Elevating Legrest (ELR) see instruc-

tions for Swing-away Footrest installation page 28.

new drawing

1. Upright Positioning

2. Adjustment

a. Lift backrest to upright position so that latch

handles (A) lock into place.

b. Backrest is ready for use.

2. Folding Backrest

a. To raise legrest, lift to desired position. Legrest

will automatically lock in place.

b. To lower legrest, while seated in chair, first lift

slightly then press release lever (G) down and

lower legrest to desired position.

a. Lift and turn backrest latch handles (A) inward

or outward.

b. Fold backrest forward.

F. REMOTE JOYSTICK INSTALLATION

1. To Connect

a. Line up small cylindrical connector with its

receptacle on the rear of the joystick.

b. Push in firmly.

CAUTION: Backrest latches must be locked into

place before operating wheelchair.

D. SWING-AWAY FOOTRESTS

2. To disconnect

1. Installation

Pull back on the retaining ring (H) of the cylindrical

connector until it disconnects from the joystick box.

a. Place swing-away pivot pin (B) into the locating

hole (C) on top of the hanger mount with the

footrest facing outward from frame.

b. Rotate the footrest inward until latch plate locks

(D) into place on locking bolt.

G. TO ADJUST THE HEIGHT OF THE REMOTE JOYSTICK

a. Remove the two pan-head screws (A), securing

the angle bracket mount (B).

b. Remove the Joystick from the mount by unfas-

tening the two screws (C) on the underside of

the mount.

c. Position angle bracket mount such that you

achieve the desired joystick height. Four posi-

tions are available by relocating the mount

either on the top or bottom of the mounting bar

(D) and/or by rotation of the angle

bracket mount.

2. Removal

a. To remove footrest, press quick-release lever (E).

b. Rotate footrest outward and lift.

3. Height Adjustment

a. Loosen all four (4) set screws (F) in the hanger

frame tube.

b. Reposition footrest height.

c. Re-tighten all set screws (F).

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S e t - U p , A d j u s t m e n t

U s e

I X . S e t - U p , A d j u s t m e n t

U s e

2. Height Adjustment

H. REMOTE JOYSTICK SWING-AWAY RETRACTABLE

MOUNT (OPTIONAL)

a. Rotate release lever to stop.

b. Slide armrest pad up or down to desired

height.

c. Return lever to locked position.

d. Push arm pad until upper armpost locks firmly

into place.

The remote joystick is mounted with a mechanism

which allows the control to be locked in a forward or

retracted position.

Adjustment

a. To retract joystick, depress lever (E) located on

side of armrest.

b. Push joystick away from front of armrest until it

locks into retracted position.

c. To return to forward position, depress lever and

push joystick forward until it locks into place.

3. Removing Armrest

a. Rotate release lever and remove the armrest.

4. Replacing Armrest

Height-Adjustable Armrest Key

1. Inner Arm Post

a. Slide armrest back into receiver.

b. Return release lever to locked

position against armpost.

2. Receiver

3. Release Lever, Locked Position

4. Armrest Pad

5. Adjusting Armrest Receiver Fit

I. DUAL-POST HEIGHT-ADJUSTABLE ARMRESTS

To tighten or loosen the fit of the outer armpost in

the receiver:

5. Transfer Bar

The dual-post flip-back armrest can be used as either a

flip-back armrest or a removable armrest.

6. Side Panel

a. Loosen the four bolts on the sides of the

receiver.

7. Tension Adjustment Set Screw

8. Outer Arm Post

1. Installing Armrest

a. Insert front and rear posts into armrest receivers.

b. Tighten clamp levers (A) and (B) to secure armrest.

2. Set-up for Flip-back Operation

a. Loosen clamp lever (A) so front post is able to

come free.

b. Armrest now has the ability to be flipped back

without removal.

3. Set-up for Removal

b. With the armrest in the receiver, squeeze the

receiver to achieve the desired fit.

c. Tighten the four bolts.

9. Receiver Adjustment Bolts

6. Adjusting Inner Armpost Fit

a. Two set screws are installed in the outer arm-

post.

b. Turn the set screws in or out until the desired

fit is achieved.

a. Insert front and rear posts into armrest receivers

b. Loosen clamp lever (A) and (B) so front and rear

post are able to come free.

K. SEAT DEPTH

The seat depth can be adjusted in one inch increments.

c. Armrest can now be easily removed for transferring.

4. Height-Adjustment (option)

a. Release the upper securing lever (C).

b. Set at desired height

1. Seat Frame Depth Adjustment

a. To adjust, remove the two bolts (C & D) from

each side of the backrest pivot plate.

b. Reposition the backrest to the desired position.

c. Replace and retighten bolts on each side of

the backrest pivot plate.

c. Return securing lever to locked position.

d. Move armrest up or down to allow armrest to

snap into place

J. SINGLE POST HEIGHT-ADJUSTABLE ARMRESTS

(OPTIONAL)

1. Installation

a. Slide the outer armpost into the receiver mount-

ed to the wheel chair frame.

b. The armrest will automatically lock into place.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S e t - U p , A d j u s t m e n t

U s e

I X . S e t - U p , A d j u s t m e n t

U s e

MANUAL WHEELCHAIR CONVERSION KIT

2. Back Angle Adjustment on Seat Frame

a. Remove the front securing bolt (C) on the side of

the backrest hinge plate.

b. Loosen the lower rear bolt (D)

c. Set at desired angle. There are five holes (in 4º

increments) to choose from.

A. JOYSTICK

Removal

a. Disconnect the joystick by pulling back on the

retaining collar (A).

b. Remove joystick power cable from armrest.

c. Remove joystick assembly.

d. Reinstall the front bolt and tighten both bolts

securely.

B. POWER DRIVE UNIT

L. 12" DRIVE WHEEL

Detachment

Drive Wheel Position Adjustment

a. Release both quick-connect levers (B) until

completely disengaged.

b. Lift seat and main frame off of power unit.

c. Set power unit aside.

a. Remove the seat and main frame and the batteries.

b. Remove the four (4) bolts (B) using a 1/2"

wrench from each quick-connect socket.

c. Move the socket forward or backwards to the

desired position.

C. WHEEL LOCKS

d. Reinstall the four (4) bolts in the quick-connect

socket. Use a torque setting of 240 in.-lbs. (27

N.m) to tighten bolts.

Wheel locks are installed by Sunrise when requested on

the Quickie P-222.

Adjustment

M. DYNAMIC STABILIZER

The wheel locks mount on a split clamp system. Use a

torque of 100 in./lbs. (11.3Nm) when adjusting the

position of the wheel locks.

4" Rear Wheel Adjustment

a. Remove rear batteries.

b. Remove the upper pivot bolt (C)

on the rear wheel spring.

c. Set at desired height.

d. Tighten nut. Use a torque setting of 240 in.-lbs.

(27 N.m) to tighten nut.

1. Loosen the screws on the side of each clamp (C)

using a 3/16" allen wrench. Do not attempt to

remove one screw at a time.

2. Slide assembly toward rear wheel until clamp

embeds into tire to prevent wheel movement

when in the locked position.

e. Height adjustment may also be made by using extra

set of mounting holes on rear wheel mount bracket.

3. Adjust angle position. Tighten screws.

NOTE– The lowest point of the rear wheels should be 1/4" to

1/2" (6 to 13 mm) from the ground to allow for proper

clearance (with the tires properly inflated and rider

sitting in the chair). A smaller clearance produces less

rocking motion, and a larger clearance allows easier

movement on deep carpets.

NOTE– In addition to the user’s weight, the seat depth and

back angle adjustment will effect this choice. Choose

the position that provides the most comfortable transi-

tion onto and off of the dynamic stabilizer wheels.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

I X . S e t - U p , A d j u s t m e n t

U s e

I X . S e t - U p , A d j u s t m e n t

U s e

G. CHECK-OUT

D. 24" REAR WHEELS

Installation

Once the wheelchair is assembled and adjusted, it should roll smoothly and easily.

All accessories should also perform smoothly.

1. Depress the quick-release button (A) on the axle.

2. Slide it into the axle sleeve until it locks.

After the wheelchair has been set up be sure the chair performs to your specified

operational settings (see pages 37-42). If the chair does not perform to specifications,

turn the wheelchair OFF immediately and reprogram operational specifications.

E. ANTI-TIP TUBES

Sunrise Designs recommends anti-tip tubes for all

wheelchairs.

Repeat this procedure until the wheelchair performs to specifications before

attempting active use of the wheelchair.

NOTE– Use a torque setting of 100 in.-lbs. when set-

ting-up anti-tip receivers.

If you have any problems, follow these procedures:

1. Inserting Anti-Tip Tubes Into Receiver

a. Press the rear anti-tip release lever on the anti-

tip tube so that both release pins are drawn

inside.

1.Review the set-up and check-out section and operating guide to make sure

chair was properly prepared.

2.If your problem persists, contact your authorized supplier. If you still have

a problem after contacting your authorized supplier, contact Sunrise cus-

tomer service. See the introduction page for details on how to contact your

authorized supplier or Sunrise customer service.

b. Insert into the anti-tip tube receiver on the axle

tube assembly.

c. Turn the anti-tip tube down until release pin is

through the receiver.

d. Insert second anti-tip tube the same way.

2. Turning Anti-Tip Tubes Up

Turn anti-tip tubes up when being pushed by atten-

dant, overcoming obstacles or climbing curbs.

a. Press the rear anti-tip tube release lever.

b. Hold lever in and turn anti-tip tube up.

c. Release lever.

d. Repeat with second anti-tip tube.

e. Remember to return anti-tip tubes

to down position after completing maneuver.

F. INSTALLATION OF AXLE TUBE ASSEMBLY

1. Align and slide the receivers on the axle tube

assembly (A) with the guides (B) located on the

underside of the rear frame.

2. Rotate spring knobs (C) to disengage position.

3. Slide the axle tube assembly onto the guides.

4. Engage locking pins by rotating spring knob.

5. Ensure spring knob is in correct position and

locking pin is engaged.

6. Ensure 24" manual wheels and anti-tip tubes are

installed on the axle tube assembly.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O p e r a t i n g G u i d e

2. To Program Your Chair:

A. PERFORMANCE CONTROL SETTINGS

a. Turn off power to the chair.

1. It is vital to match control settings to your level

of function and ability.

2. Consult your health care professional and your

supplier to select the best control settings for

you.

3. Check and adjust the settings every six to twelve

months (or more often, if needed).

4. Adjust the control settings immediately if you

notice any change in your ability to:

•Control the joystick.

•Hold your torso erect.

•Avoid running into objects.

5. Control Settings are adjusted through the use of

the Quickie QTRONIX Programmer. See your suppli-

er if you do not own a Quickie QTRONIX

Programmer pad.

b. Insert Qtronix Programmer plug (A) into the

Programmer/Charger socket (B) on the front of

the joystick.

c. Turn on power to the chair; program as needed.

d. Remove plug and cycle ON/OFF switch to drive

chair.

NOTE– Review the Qtronix Programmer Owner’s Manual

for more details on how to program your chair.

NOTE– Program settings that are not matched for the

capabilities of the rider can result in serious

injury. Do not alter settings without the advice

of your health care professional.

C. THERMAL ROLL-BACK

Your chair has a thermal roll back circuit.

This protects the controller from damage due to over-

heating. In extreme conditions (such as repetitive hill

climbing) the circuit will decrease the power to your

motors. This allows the chair to operate at a reduced

speed. When the controller cools, the chair will return

to normal speed.

B. QTRONIX PROGRAMMING PAD (OPTIONAL)

Program settings beyond the ability of the rider

can result in serious injury. Consult your health

care advisor before you alter settings.

1. Notes–

D. CIRCUIT BREAKERS

The Qtronix Programmer lets you adjust the control

settings of the P-222. You can customize a program for

yourself or select the standard program.

1. Notes–

Your Quickie P-222 has a single circuit breaker (A).

• In the unlikely event of a short circuit or heavy

overload, all power to your chair will be shut off.

• To reset your chair, depress the circuit breaker

button (A). A few minutes wait is required before

the circuit breaker will reset.

• acceleration rate

• deceleration rate

• turn acceleration

• turn deceleration

• forward speed (max & min)

• reverse speed (max & min)

• turn speed (max & min)

• steer correct

2. Repeated Shutdown:

If the chair continues to shut down after resetting,

have it serviced by a supplier.

• 4-axis joystick throw

• sleep timer

• read timer

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O p e r a t i n g G u i d e

5. Joystick (E)

E. JOYSTICK ASSEMBLY

The joystick controls the direction and speed of your chair. Turn the chair on and move

the joystick in the direction you want to go.

The joystick connects to a controller, which controls

the chair’s performance. The joystick assembly consists

of the following parts:

• Moving the joystick from the neutral (center) position disengages the motor

locks, allowing the chair to move.

• The chair will move faster the more you move the joystick away from neutral.

1. Speed Control Knob (A)

Use the speed control knob to adjust the maximum

speed of your chair. Turn it counter-clockwise to reduce

speed; turn it clockwise to increase speed.

NOTE– If your speed becomes hard to manage, release the Joystick and the chair will

come to a complete stop.

• When you release the joystick it will return to neutral; the chair will slow to a

stop and the motor locks will reengage.

• We recommend that you switch the chair off if you stop for any length of time.

This will conserve battery power.

2. Battery Charge Indicator (B)

• Green lights indicate that batteries are fully

charged.

Remote Joystick

• Yellow lights indicate that batteries need

recharging.

• When the lights stay in the red band, the batter-

ies must be recharged.

NOTE– Once the chair stops, switching the chair off will not affect the motor locks.

6. Joystick Boot (F)

Make sure the boot is not torn or cracked (this could allow debris, water or moisture

to enter). If the boot is torn or cracked, replace it as soon as you can.

3. On/Off Mode switch (D)

The on/off mode switch is located on the rear face of

the joystick housing. It is a toggle switch. Turning the

chair on or off, is accomplished by pressing the switch

downward. The switch will automatically return to the

center point. Alternate locations exist for this switch.

Please see your supplier in the event that you wish to

relocate or re-orient this switch.

7. Remote Switch Jacks (optional) (I)

Two 1/8" switch jacks are optional to provide remote switch control of the on/off

power function and the mode select function. Any of the single switches offered by

Sunrise Medical can be used to connect to either or both of these jacks (except the

single zero touch switch).

4. Mode Switch (D)

1.Never use the ON/OFF switch to stop your chair except in an emergency.

This will result in an abrupt stop, and may cause you to fall.

2.To slow or stop your chair, return the joystick to neutral.

The on/off mode switch allows you to select from 5

(five) different programmable drive profiles or actuator

mode sets.

• Push up the on/off mode select toggle switch to

index among the five drive and actuator modes.

The selected mode indicator will flash.

• Push joystick either left or right to select one of

the five drive profiles. To select the actuator

modes, push the mode select switch twice.

• The drive profiles are indicated by the mode indi-

cators (G) and the actuators are indicated by the

four actuator lights (H).

• To exit drive or actuator mode select, simply push

the on/off/mode toggle up one or more times

until the indicator no longer flashes, or push the

joystick forward or reverse to begin driving.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X . O p e r a t i n g G u i d e

X I . B a t t e r i e s

A. INTRODUCTION

F. MOTOR LOCKS

1. Notes–

Disconnect the motor locks when you need to manually

push the chair. (For example, in an emergency,

or if batteries fail).

• Batteries supply the power for your chair. They contain a finite amount of

energy and have limits on how long they can store and supply energy.

• You can charge batteries only a certain number of times before they will fail and

no longer hold a charge.

• For answers to questions about batteries, consult your supplier.

2. Use Proper Batteries:

1.Do not disengage motor locks unless power to

the chair is off.

Your chair operates on two 12 volt batteries.

2.With the brakes released, the chair will not

operate and the battery charge indicator will

flash 9 bars rapidly (if power to the chair is on).

3.Be aware that the chair will not have brakes

in the free-wheel position.

• They should be Group 24 size with a minimum of 65 ampere hour rating. Only

deep cycle sealed case construction batteries should be used in this device.

• Connecting configuration. They should have a post and clamp style connection.

• When you buy a replacement, insist on a deep cycle sealed case type. Do not

use a car starter battery.

4. Make sure that the person pushing the chair has

full control when motor locks are disengaged.

1. To Disengage Motor Locks:

Lift the lever (A) to the free-wheel position.

2. To Engage Motor Locks:

3. Breaking In:

• A battery requires “breaking-in” for the first 6 to 12 charges. It will not accept a

full charge for this period.

• It is best to limit the length of your trips until you break the batteries in

and you know the range of your chair.

Push the lever (A) down into the drive position.

4. Discharged Batteries:

• Never allow a battery to completely discharge. If you operate your wheelchair

until it has almost stopped, you will greatly reduce the life of your batteries.

• Never let a battery sit in a discharged condition. Give unused or stored batteries

a full charge once per month.

• Always fully charge the batteries. Avoid “topping off” with frequent charges.

Never connect a life support or auxiliary device to a wheelchair battery.

The electrical system may fail, and result in severe injury to or death of rider.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I . B a t t e r i e s

C. ACID BURNS (UNSEALED WET CELL BATTERIES)

B. BATTERY CHARGER

Acid in batteries is corrosive. It can cause serious

burns to the eyes and skin and can damage floors, fur-

niture, clothing and your wheelchair.

A battery charger produces a direct current (DC). When applied to a

discharged battery, this reverses the chemical reaction that led to its discharge.

1. Charge Rate. How fast a battery will charge depends on:

• Its electrical capacity; state of charge; electrolyte temperature, and;

internal condition.

• The DC output of the charger. (The charge rate will vary if the alternating

current (AC) supply is higher or lower than 110 volts).

2. Caution — To Avoid Damage to the Charger:

1.Use extreme care not to spill acid when you

handle batteries. Keep batteries upright.

2. Avoid contact of acid with bare skin or clothing.

3.Always wear rubber gloves and safety glasses

when you handle batteries.

4.If acid contacts your skin or clothing, wash

immediately with soap and water.

5.If acid contacts your eyes, immediately flood

eyes with cold running water for at least 15

minutes. Seek medical attention immediately.

• Never place the charger on top of a battery during charging. (Gases from the

battery can damage the charger and may lead to an explosion or fire).

• Never place a battery on top of the charger.

• Never expose charger to rain or snow.

• Never unplug charger by pulling on the electrical cord. This will damage the

cord.

• Never open a charger or attempt to repair it yourself. Return charger to Sunrise

or have repairs made only by a qualified person.

D. CONNECTING BATTERIES IN BATTERY COMPARTMENT

• Keep cord out of the way, where it will not be stepped on, tripped over,

or damaged.

3. Caution — To Avoid Damage to the Battery:

1.Batteries weigh up to 55 lbs. (25 kg). Take

care to avoid injury when lifting.

2.Keep batteries upright. Take care not to spill

acid (wet cell batteries).

3.Always wear rubber gloves and safety glasses

when you handle batteries.

• Make sure you use the correct setting for sealed (gel) batteries (located on the

off-board charger).

• Never charge a frozen battery. A fully charged battery will rarely freeze, but the

fluid in a discharged battery can freeze at 16 degrees Fahrenheit (minus 9

degrees Centigrade). If you suspect a battery is frozen, thaw it before charging.

4.Before working around batteries, remove all

metal personal effects, such as necklaces,

rings, watches, pins and other metal jewelry

that might contact battery terminal and cause

a short.

Lead acid batteries generate explosive gas while charging. Completely read

and follow all warnings about the batteries in this user instruction manual

and any labels applied to the product. Failure to do so could result in fire,

explosion, injury and/or death.

1. Lift batteries into battery compartment.

Batteries weigh up to 55 pounds (25 kg).

Lifting batteries may cause back strain. If you

fail to heed these warnings severe injury may

occur to you.

2. Connect and disconnect battery cables with cau-

tion. Connect the red lead to the positive termi-

nal and the black lead to the negative terminal.

Do this for each battery.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I . B a t t e r i e s

Always:

3. Tighten all terminal fasteners using two 1/2" box

end wrenches to 60 in-lbs (6.8 N.m).

1. Use the charger that comes with

your wheelchair. Read and follow all instructions and warnings.

2. Make sure room is well ventilated.

3. Turn off all power to your chair.

4. Connect and disconnect battery cables with caution. Only connect the charger to

the power supply after the charger has been connected to the chair

5. Make sure to allow enough time to fully charge batteries.

Note: Batteries should never be left for long periods in the discharged state.

Unused or stored batteries should be given a charge once per month.

6. Charge batteries by engaging charger connector (A) to the charger/programmer

port (B) located on the joystick.

4. Place the battery compartment lid on power

base and secure using the two (2) quarter turn

fasteners (push down on fasteners).

Never make direct contact across both battery

terminals, as an explosion may occur. A spark

may result in an explosion and/or fire resulting

in severe injury or death.

F. DISPOSING OF BATTERIES

E. CHARGING BATTERIES

1. All batteries once they have reached the end of their useful life are deemed to

be hazardous waste.

2. For further information on handling and recycling contact your local

recycling authority.

To avoid the risk of severe injury or death from

electrical shock, fire or explosion while charging:

1.Never connect charger to a 240 volt source.

The main input voltage is 110 volts. For

wheelchair manuals to be used outside the

U.S. omit (1).

3. Always dispose of product through a recognized agent.

2.Never touch the charger after it is connected

to an electrical outlet. This may cause electri-

cal shock.

•Connect charger to the power supply ONLY

AFTER you connect charger to the battery.

•Never connect or disconnect charger from

battery while there is power to the charger.

3.Never use an extension cord. Use of an

improper cord could damage the charger, or

cause a fire or electrical shock.

4. A battery emits explosive hydrogen gas during

charging. To reduce the risk of fire or explosion:

•Make sure area is well vented. Never charge

battery in a closed-in area.

•Never smoke or allow a spark, flame or high

heat near battery during changing.

•Never allow metal tools or chair parts to make

direct contact across both battery terminals.

5.Never look directly into cells when charging

battery.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I . M a i n t e n a n c e

D. BATTERY MAINTENANCE

A. NOTES

1. Proper maintenance will improve performance and extend the useful life

of your chair.

1.To prevent an acid spill, always keep batteries upright (wet cell batteries).

2.Never smoke or hold an open flame near batteries.

3.Always wear rubber gloves and safety glasses when you handle batteries.

1. Maintenance Schedule:

2. Clean your chair regularly. This will help you find loose or worn parts and will

make your chair easier to use.

3. To protect your investment, have all major service and repair work done by your

supplier.

This varies for different types of batteries. Always follow the instructions supplied with

your batteries.

1.Your chair needs regular maintenance for peak performance and to avoid

injury from chair failure, damage or premature wear.

NOTE– Always wear rubber gloves and safety glasses when you handle or service batteries.

2. Adding Water: (Wet Cells Only)

2.Inspect and maintain this chair strictly per the “Maintenance Chart”. (p. 51)

3.If you detect a problem, make sure to service or repair the chair before use.

4.At least once a year, have a complete safety check and service of your chair

performed by a supplier.

• Wet-type lead acid batteries need periodic replacement of water due to evaporation.

NOTE– Use distilled water only.

• Check the battery fluid level about once a week. When you remove the stoppers

(on top of the battery) there should be one-eighth to one-quarter of an inch of

fluid above the internal plates. Do not overfill.

B. CLEANING

1. Paint Finish:

3. Corrosion:

• Clean the paint finish with mild soapy water monthly.

• Protect the paint with a coat of non-abrasive auto wax every three months.

2. Motors:

• Clean around motor area weekly with a slightly damp (not wet) cloth.

• Wipe off or blow away any fluff, dust, or dirt on or around the motors.

• Note: You do not need to grease or oil the chair.

3. Upholstery:

Check battery terminals often for corrosion.

a. If corrosion is present, use a wire brush to clean the terminals.

NOTE– Always wear safety glasses and rubber gloves.

b. Use baking soda to neutralize acid.

c. Use petroleum jelly to re-grease the terminals after connecting cable to battery.

(Completely cover the terminal nut and bolt, cable clip and any exposed cable

with jelly).

• Hand-wash only as needed. Machine washing may damage fabric.

• Drip-dry only. Heat from a dryer may damage fabric.

4. For Answers To Questions: Contact your supplier.

NOTE– Washing the fabric may decrease fire retardant properties.

C. STORAGE TIPS

1. Store your chair in a clean, dry area. If you fail to do so, parts may rust or corrode.

2. Before using your chair, make sure it is in proper working order. Inspect and service

all items on the “Maintenance Chart” (See p. 51)

3. If you store this chair for more than three months, have it inspected by a supplier

before use.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I . M a i n t e n a n c e

2. 12" (310 mm) Drive Wheels:

E. PNEUMATIC TIRES

a. Elevate and securely support chair so that wheel is off the ground.

Release all air from tire.

1.Do not use this chair if any of the tires are

under- or over-inflated.

2.Low pressure in a tire may cause the chair to

veer to one side and result in loss of control.

3.An over-inflated tire may burst.

4.Never use a gas station pump to inflate a tire.

Such pumps provide air at high volume, and

may cause tire to burst.

1. Check for signs of wear and correct air pressure

in pneumatic tires weekly.

b. Remove four (4) screws (A) from rim using a 9/16" socket wrench.

c. Make sure all air has been removed from tire. Remove the four bolts from rim.

Separate two halves of rim.

d. Repair or replace inner tube. Reassemble the wheel.

Use a torque setting of 120 in.-lbs. (13.5 N.m) to re-tighten bolts.

e. Inflate tire to proper pressure level (listed on tire sidewall).

G. ORDERING PARTS

When you order parts, provide the following:

1. Model of chair

2. Serial number of chair

2. For best performance, inflate tires to the same

pressure level, as shown on the tire sidewall:

•8" & 9" (200 & 250mm) pneumatic casters–

30 to 40 psi (207 to 275 kpa)

3. Left hand or right hand control

4. Part number, description and quantity of parts you need.

5. State reason for replacement.

•12" (310 mm) pneumatic drive wheels–

35 to 45 psi (240 to 310 kpa)

3. CAUTION– To prevent tire damage:

•Use a hand pump (or a low volume air pump)

to inflate tires.

H. MAINTENANCE CHART

You should check the items on this chart at the indicated intervals. If any of the items

are loose, worn, bent or distorted, immediately have them checked and/or repaired by

your authorized Sunrise supplier. Frequent maintenance and servicing will improve per-

formance, extend wheelchair life, and help prevent injuries.

•Use a tire gauge to check pressure.

F. TO REPAIR OR REPLACE A TIRE

Residual air pressure in tires can cause severe

injury. Make sure you release all air in tire

before attempting to service or repair tires.

1. 8" & 9" (200 & 250mm) Caster Wheels:

a. Release all air from tire.

CHECK...

Charge Batteries

ꢀ

b. Remove caster wheel from fork using a 1/2" wrench.

c. Make sure there is no residual air in tire before

you remove bolts that hold the two rim halves

together.

d. Remove four bolts from rim using a #3 phillips

screwdriver. Separate two halves of rim.

e. Repair or replace inner tube.

f. Reassemble the caster wheel; make sure the

bearing spacer is in place and all four bolts are

tightened to a torque of 60 in.-lbs. (6.8 N.m).

g. Mount caster wheel onto fork. Install washers

correctly tighten bolt to 240 in.-lbs. (27 N.m).

h. Inflate tire to proper pressure level.

Check tires for proper inflation level

Check batteries for proper electrolyte level (wet only)

Check plugs and connectors for proper connections

Check all moving parts for wear

ꢀ

Inspect all nuts, bolts and fasteners for looseness or wear

Inspect upholstery for wear

Service by authorized supplier

ꢀ

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

X I I I . W i r i n g D i a g r a m

X I V . S u n r i s e L i m i t e d W a r r a n t y

1. FOR LIFE

WIRING DIAGRAM DETAIL

We warrant the main frame of this wheelchair against defects in materials and work-

manship for the lifetime use of the first consumer purchaser.

2. ADDITIONAL WARRANTY

We warrant Sunrise-made components of this wheelchair against defects in materials

and workmanship as follows:

a. Main electronic controller—For two (2) years from the date of first consumer

purchase.

b. Motors, gear boxes and remote joystick—For one (1) year from the date of first

consumer purchase.

c. All other original components (such as wheels, upholstery, plastic, rubber parts

and painted surfaces)—For three (3) months from the date of first consumer

purchase.

3. LIMITATIONS

a. We do not warrant damage due to:

•Neglect, misuse, or improper installation or repair.

•Use of parts or changes not authorized by Sunrise.

•Exceeding the weight limit of 250 pounds (113 kg) or 350 lbs (159 kg) for

heavy duty option.

b. This warranty is void if the original chair serial number tag is removed or altered.

c. This warranty applies in the USA only. Check with your supplier to find out if

international warranties apply.

4. WHAT WE WILL DO

Our sole liability is to repair or replace covered parts.

This is your only remedy for consequential damages.

5. WHAT YOU MUST DO

a. Return the warranty card.

b. Obtain from us, while this warranty is in effect, prior approval for return or

repair covered parts.

c. Return the wheelchair or part(s), freight pre-paid, to Sunrise Mobility Products

Division at: 2842 Business Park Ave., Fresno, CA 93727-1328.

d. Pay the cost of labor to install or repair parts.

6. NOTICE TO CONSUMER

There are no other express warranties. To the extent permitted by law, any implied

warranty (including a warranty of merchantability or fitness for a particular purpose) is

limited to:

a. One (1) year from the first consumer purchase, and

b. Repair or replacement of the defective part only.

This warranty gives you certain legal rights. You may also have other rights that vary

from state to state.

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

N o t e s

930466 Rev. A

Download from Www.Somanuals.com. All Manuals Search And Download.

Sony DVD Player DVP CX777ES B User Manual
Sony Portable Radio ICF 620R User Manual
Sony Portable Speaker SRS PC71 User Manual
Sony Security Camera SNC CH140 User Manual
Sony TV VCR Combo KV 14VM5MT KV 21VM6MT User Manual
Star Micronics Printer NB 15 User Manual
Stow Music Mixer MS 40M User Manual
Summer Infant Safety Gate 07260 User Manual
Sylvania MP3 Player SMPK2242 User Manual
Symphonic DVD VCR Combo SD7S3 User Manual