StorageTek™
L40
Tape Library
Installation Manual
96053
Revision: L
Download from Www.Somanuals.com. All Manuals Search And Download.
L40
Tape Library
Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright 2006 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved.
Sun Microsystems, Inc. has intellectual property rights relating to technology that is described in this document. In particular, and without
or more additional patents or pending patent applications in the U.S. and in other countries.
This document and the product to which it pertains are distributed under licenses restricting their use, copying, distribution, and
decompilation. No part of the product or of this document may be reproduced in any form by any means without prior written
authorization of Sun and its licensors, if any.
Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered
trademark in the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, Java, AnswerBook2, docs.sun.com, and Solaris, StorageTek, VolSafe, TimberWolf, TimberLine, and
RedWood are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and in other countries.
All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in
other countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun
acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the
computer industry. Sun holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s
licensees who implement OPEN LOOK GUIs and otherwise comply with Sun’s written license agreements.
U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and
applicable provisions of the FAR and its supplements.
DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY
INVALID.
Copyright 2006 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés.
Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et
sans la limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à http://
autres pays.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la
distribution, et la décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque
moyen que ce soit, sans l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y en a.
Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié
par des fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, Java, AnswerBook2, docs.sun.com, et Solaris, StorageTek, VolSafe, TimberWolf, TimberLine, and
RedWood sont des marques de fabrique ou des marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays.
Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International,
Inc. aux Etats-Unis et dans d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun
Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés.
Sun reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou
graphique pour l’industrie de l’informatique. Sun détient une license non exclusive de Xerox sur l’interface d’utilisation graphique Xerox,
cette licence couvrant également les licenciées de Sun qui mettent en place l’interface d ’utilisation graphique OPEN LOOK et qui en outre
se conforment aux licences écrites de Sun.
LA DOCUMENTATION EST FOURNIE "EN L’ÉTAT" ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES
EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y
COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE
UTILISATION PARTICULIERE OU A L’ABSENCE DE CONTREFAÇON.
We welcome your feedback. Please contact the Sun Learning Services Feedback System at:
or
Sun Learning Services
Sun Microsystems, Inc.
One StorageTek Drive
Louisville, CO 80028-3256
USA
Please include the publication name, part number, and edition number in your correspondence if they are
available. This will expedite our response.
ii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Summary of Changes
EC
Date
Edition
First
Description
111666
111717
111732
111784
111828
111854
111875
111923
111948
111976
114172
August 2001
January 2002
March 2002
August 2002
February 2003
June 2003
Initial release
Second
Third
Fourth
Fifth
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Refer to this edition for a description of the changes.
Sixth
November 2003 Seventh
July 2004
Eighth
Ninth
Tenth
L
January 2005
May 2005
October 2006
Cover, Copyright, Preface: Added Sun verbiage and
branding.
96053
Revision L
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Summary of Changes
This page intentionally left blank.
iv
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Alert Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Customer Resource Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Partners Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Global Services Support Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi
Documents on CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi
Hardcopy Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi
Lifting Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xviii
Shoulder, Elbow, Wrist, and Hand Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xviii
Rack Safety and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xix
Fiber-optic Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xix
Fiber-optic Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx
ESD Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii
Access the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxiii
Replace Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxiii
Clean Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxiv
96053
Revision L
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv
Precauciones de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv
Técnicas de levantamiento de objetos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxvi
Seguridad de hombros, codos, muñecas y manos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxvi
Etiqueta del producto láser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxviii
Prevención de daños por descargas electrostáticas (DES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx
Precauciones contra descargas electrostáticas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxx
Procedimiento de protección contra descargas electrostáticas . . . . . . . . . . . . . . . . . . . . . . . . . .xxxi
Prepare el área de trabajo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxxi
Limpie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii
1: Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Quick Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Standard Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Preparing for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Unpacking the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Inspecting the Library and Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Preparing the Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Positioning the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Choosing SCSI HVD or LVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
SCSI Cable Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Host Bus Adapter Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
SCSI Device/Bus Type Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Installing the External Fibre Channel Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Connecting the External SCSI Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Connecting Fiber and SCSI Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Attaching the Personality Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
Attaching the Cell Barrier Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Inserting the Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
Drive Compatibility Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
Installing the Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26
Powering-on the Library and Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29
Recording the Configuration Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29
vi
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2: Locations, Specifications, and Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Library Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Library Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Drive and Cartridge Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Drive Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Power Cord Numbers and Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
External Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
A: SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
SNMP Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
SNMP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Management Information Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Starting SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Index-1
96053
Revision L
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
Figure 1-1. Unpacking the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Figure 1-2. Attaching the Cell Barrier Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Figure 1-3. Determining the Valid Storage Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
Figure 1-4. Inserting the Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
Figure 2-1. Front View of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Figure 2-2. Rear View of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Figure 2-3. Internal View of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-4. Robotic Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-5. DLT Drive Label Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Figure 2-6. Ultrium Drive Label Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-7. L40 Desktop Version Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-8. L40 Rack Version Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
96053
Revision L
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Tables
Table 1-1. SCSI Cable Length Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Table 1-2. SCSI Device/Bus Types: Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Table 1-3. LTO Drive Backward Readability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
Table 1-4. SCSI Device/Bus Types: Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
Table 1-5. Compatible Drives and Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
Table 1-6. L40 Tape Library Configuration Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-30
Table 2-1. Library Environment Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Table 2-2. Library Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Table 2-3. Drive and Cartridge Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Table 2-4. Drive Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Table 2-5. Country-specific Power Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Table 2-6. Non-country-specific Power Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Table 2-7. External Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
96053
Revision L
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
x
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This manual is for either customers or service representatives, depending upon the
service contract. When you have completed the procedures in this manual, refer to the
Most of the information pertains to library hardware. For specific drive information or
for client-generated software commands and console messages, refer to your drive or
software documentation.
■ Organization
This manual has two chapters, an appendix, and an index:
“Hardware Installation” tells you how to install the hardware portions
of the library. It contains a “Quick Installation Procedure” for
experienced users and a “Standard Installation Procedure” that guides
you through each step of the installation.
“Locations, Specifications, and Cables” identifies library components,
drive label locations, specifications, and external cable part numbers.
Management Protocol (SNMP).
96053
Revision L
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Alert Messages
Alert messages call your attention to information that is especially important or that has a
unique relationship to the main text or graphic.
Note: A note provides additional information that is of special interest. A note might
point out exceptions to rules or procedures. A note usually, but not always,
follows the information to which it pertains.
CAUTION:
A caution informs you of conditions that might result in damage to
hardware, corruption of data, or corruption of application software.
A caution always precedes the information to which it pertains.
WARNING:
A warning alerts you to conditions that might result in long-term health
problems, injury, or death. A warning always precedes the information
to which it pertains.
■ Mensajes de alerta
Los mensajes de alerta llaman la atención hacia información de especial importancia
o que tiene una relación específica con el texto principal o los gráficos.
Nota: Una nota expone información adicional que es de interés especial. Una nota
puede señalar excepciones a las normas o procedimientos. Por lo general, aunque
no siempre, las notas van después de la información a la que hacen referencia.
PRECAUCIÓN:
Una precaución informa sobre situaciones que podrían conllevar
daños del hardware, de los datos o del software de aplicación.
Las precauciones van siempre antes de la información a la que
hacen referencia.
ADVERTENCIA:
Una advertencia llama la atención sobre condiciones que podrían
conllevar problemas de salud crónicos, lesiones o muerte.
Las advertencias van siempre antes de la información a la que
hacen referencia.
xii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Conventions
Typographical conventions highlight special words, phrases, and actions in this
publication.
Item
Example
Description of Convention
MENU
Buttons
Font and capitalization follows label
on product
Commands
Mode Select
Initial cap
Document titles
Emphasis
System Assurance Guide
not or must
Italic font
Italic font
File names
fsc.txt
Monospace font
Hypertext links
Figure 2-1 on page 2-5
Blue (prints black in hardcopy
publications)
Indicators
Open
Font and capitalization follows label
on product
Jumper names
Keyboard keys
TERMPWR
All uppercase
<Y>
Font and capitalization follows label
on product; enclosed within angle
brackets
<Enter> or
<Ctrl+Alt+Delete>
Menu names
Configuration Menu
Capitalization follows label on
product
Parameters and variables
Path names
Device = xx
c:/mydirectory
SER1
Italic font
Monospace font
Port or connector names
Font and capitalization follows label
on product; otherwise, all uppercase
Positions for circuit breakers,
jumpers, and switches
ON
Font and capitalization follows label
on product; otherwise, all uppercase
Screen text (including screen downloading
captures, screen messages, and
user input)
Monospace font
Power
Switch names
Font and capitalization follows label
on product
URLs
Blue (prints black in hardcopy
publications)
96053
Revision L
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Related Publications
Refer to the following publications for additional information:
Library Documentation
Part Number
MT5011
96026
L40 Tape Library Ordering Guide
L40 Tape Library Service Manual
L40 Tape Library User’s Guide
96005
L40/80 Tape Library CRU Instructions
L40/80 Tape Library Drives CRU Instructions
96031
96006
Tape Drive Documentation
Part
DLT 7000 Tape Drive Product Manual
DLT 8000 Tape Drive Product Manual
DLT1 Installation and Operations Guide
DLT1 Product Specification
31313450x
Quantum: 81-60118-0x
Benchmark: 000826-0x
Benchmark: 000827-0x
CD included with drive
CD included with drive
CD included with drive
CD included with drive
SDLT 220, 320 and 600 Product Manual
Hewlett Packard LTO Ultrium Publication
IBM LTO Ultrium Publication
Quantum’s Certance LTO Ultrium Publication
Other Publications
Part Number
ANSI X3/TR-1-82
American National Standard Dictionary for Information
Processing Systems
American National Standard Magnetic Tape and Cartridge ANSI X3B5/87-009
for Information Interchange
Crossroads Fibre Router User’s Manual
StorageNet 3300 Fibre Channel Router User Manual
Fiber Optic User’s Guide
DS30110
461273-01
9433
Magnetic Tape Labels and File Structure for Information
Interchange
ANSI X3.27-1978
SCSI-3 Parallel Interface (SPI)
Small Computer System Interface
ANSI X3T9.2/91-010R7
ISO 9316:1989
xiv
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Additional Information
Sun Microsystems, Inc. (Sun) offers several methods for you to obtain additional
information.
Sun’s External Web Site
Sun’s external Web site provides marketing, product, event, corporate, and service
information. The external Web site is accessible to anyone with a Web browser and an
Internet connection.
The URL for StorageTek™ brand-specific information is:
Customer Resource Center
The Sun StorageTek product Customer Resource Center (CRC) is a Web site that enables
members to resolve technical issues by searching code fixes and technical documentation
for StorageTek brand products. CRC membership entitles you to other proactive services,
such as HIPER subscriptions, technical tips, answers to frequently asked questions,
addenda to product documentation books, and online product support contact
information. Customers who have a current warranty or a current maintenance service
agreement may apply for membership by clicking on the Request Passwordbutton
on the CRC home page. Sun employees may enter the CRC through the SunWeb
PowerPort.
Partners Site
The StorageTek Partners site is a Web site for partners with a StorageTek Partner
Agreement. This site provides information about products, services, customer support,
upcoming events, training programs, and sales tools to support StorageTek Partners.
Access to this site, beyond the Partners Login page, is restricted. On the Partners Login
page, employees and current partners who do not have access can request a login ID and
password and prospective partners can apply to become StorageTek resellers.
The URL for the StorageTek Partners site is:
The URL for partners with a Sun Partner Agreement is:
96053
Revision L
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Global Services Support Tools
Global Services Support Tools site (also called Field Tools) provides tools that aid in the
sales and support of Sun StorageTek brand products and services. This is an internal Web
site for employees.
The URL for the Global Services Support Tools is http://sunsolve.central.sun.com/
handbook_internal/FieldTools
Documents on CD
Documents on CD (3106600xx) contains portable document format (PDF) files of Sun
StorageTek brand product publications. To order Documents on CD, contact your local
Customer Services Logistics Depot. Documents on CD is only for employees.
Hardcopy Publications
You may order paper copies of publications listed on the CRC or included on the
Documents on CD.
Service publications have numeric part numbers. To order paper copies of service
publications, contact your local Customer Services Logistics Depot.
xvi
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
The following pages describe common practices concerning electrical safety, ergonomics,
rack installation, fiber optics, and electrostatic discharge.
■ Safety Precautions
WARNING:
Potential injury: On-the-job safety is important; therefore, observe the
following safety precautions while you are engaging in any maintenance
activity. Failing to follow these precautions could result in serious injury.
Remove all conductive jewelry, such as watches and rings, before you
service powered-on equipment.
•
Avoid electrical shock. Be careful when you work near power connectors and
supplies.
•
Power-off the equipment that is being serviced before you remove a field replaceable
unit (FRU) or other component. Remember that dangerous voltages could still be
present in some areas even though power is off.
•
•
•
Ground all test equipment and power tools.
Do not remove, cut, or relocate any floor tiles indiscriminately. Before you
manipulate floor tiles, be sure that you understand the customer’s environment and
receive the customer’s approval. Remember, each situation is different.
•
Enforce good housekeeping practices in the equipment area to help prevent fire and
accidents.
Note: Important things to investigate and to be aware of include the use of Halon®
gas, under-the-floor smoke detectors, and cables to other equipment installed
nearby.
96053
Revision L
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Lifting Techniques
Lifting, regardless of how much or how little, can create serious back stress. If you follow
these guidelines, you can reduce the risk of back injury:
•
Do not twist your body to pick up something or to put it down. Twisting puts
extreme pressure on your back, especially when you lift or carry objects. Instead of
twisting, make the task two separate moves; first lift, and then use your feet to turn
your body.
•
•
Plan the lift: first examine the object and then determine how it will be lifted and
where it will be placed.
Choose the appropriate lifting technique. Examine the weight, size, location,
frequency, and direction of the lift. Plan to avoid awkward postures, and determine if
material-handling aids are needed.
•
Place your feet shoulder-width apart, and place one foot a little behind the other.
Keep your back straight because even light loads can significantly increase pressure
on your spine when you lean forward.
•
•
Whenever you can, grip the load with your whole hand, and use two hands.
Carry objects at elbow height and close to your body. The farther away you hold an
object, the more force it puts on your lower back.
•
•
Lift with your legs instead of your back. Leg muscles are some of the strongest in the
body. When you squat and lift with your legs, you can lift more weight safely.
Alternate lifting tasks with tasks that are less stressful to the same muscles. This
technique ensures that your muscles have some recovery time.
Shoulder, Elbow, Wrist, and Hand Safety
Follow these guidelines to minimize the possibility of injury to your shoulders, elbows,
wrists, and hands.
•
Work within your safety zone—the area between shoulder level and knuckle level of
your lowered hands. You face less chance of injury when you work or lift in this area.
•
Keep your elbows bent to keep loads close to your body and to decrease the amount
of force necessary to do the job. If you use this posture, you will put less weight and
pressure on your shoulder.
•
•
Be sure to keep your wrists straight. Avoid bending, extending, or twisting your
wrists for long periods of time.
Do not use a pinch grip to lift large or heavy loads because the way you lift also can
affect the tendons in your hand. When you grasp an object between your thumb and
fingers, you put a lot of tension on hand and wrist tendons. Use both hands—use
one for a while, and then use the other—to give them rest.
xviii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Rack Safety and Precautions
WARNING:
Possible personal injury:
•
Lifting hazard: The library weighs 44.45 kg (98 lb) plus the weight of
the drives. Use at least two people and a mechanical device to lift and
position the library. Make sure you read the information in
“Lifting Techniques” on page xviii before beginning.
•
Also consider the library’s total weight when you are placing other
equipment into the rack. To prevent an unbalanced situation, install
the heaviest equipment on the bottom and the lightest equipment on
the top. Failure to do so might cause the rack to become unstable
and tip over.
Observe the following safety precautions when you are installing the library into a rack:
•
If the rack has front or rear doors, do not allow the doors to interfere with the
library’s ventilation. The rack’s internal ambient temperature should not exceed the
recommended operating temperature range of the library. The maximum rack air
ambient temperature is 40°C (104°F).
•
•
Ensure that rack doors provide adequate clearance to the library.
Ensure that the combination of the library with other equipment in the rack does not
create an overcurrent condition, whether the equipment is connected directly to the
branch circuit or to a power distribution strip.
•
Ensure that all equipment in the rack has reliable earth ground, whether the
equipment is connected directly to the branch circuit or to a power distribution strip.
Note: The library relies on the ground pin of the power cord for its earth ground.
■ Fiber-optic Safety
WARNING:
Eye hazard. Never look directly into a fiber-optic cable, a fiber-optic
connector, or a laser transceiver module. Hazardous conditions might
exist from laser power levels that are capable of causing injury to the
eye.
Be especially careful when using optical instruments with this
equipment. Such instruments might increase the likelihood of eye injury.
The laser transceivers in fiber-optic equipment can pose dangers to personal safety.
Ensure that anyone who works with this Sun StorageTek equipment understands these
dangers and follows safety procedures. Ensure that the optical ports of every laser
transceiver module are terminated with an optical connector, a dust plug, or a cover.
96053
Revision L
xix
Download from Www.Somanuals.com. All Manuals Search And Download.
Each fiber-optic interface in this Sun StorageTek Fibre Channel equipment contains a
laser transceiver that is a Class 1 Laser Product. Each laser transceiver has an output of
less than 70 μW and a wavelength of 850 nm. Sun StorageTek’s Class 1 Laser Products
comply with EN60825-1(+A-11) and with sections 21 CFR 1040.10 and 1040.11 of the
Food and Drug Administration (FDA) regulations.
The following translations are for users in Finland and Sweden who wish to identify laser
safety and classification:
CLASS 1 LASER
LUOKAN 1 LASERLAITE
KLASSE 1 LASER APPARAT
Laser Product Label
In accordance with safety regulations, a label on each Sun StorageTek Fibre Channel
product identifies the laser class of the product and the place and date of the
manufacturer. The label appears on top of a Fibre Channel tape drive and near the Fibre
Channel connectors on a Fibre Channel tape library. A copy of the label is shown here:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A LASER DE CLASSE 1
COMPLIES WITH 21 CFR 1040.10 AND 1040.11
Fiber-optic Cable Installation
Follow these guidelines when you install fiber-optic cables:
1. Cable routing:
•
Raised floor: You may install fiber-optic cables under a raised floor. Route them
away from any obstruction, such as existing cables or other equipment.
•
Cable tray or raceway: Place the cables in position; do not pull them through
the cable tray. Route the cables away from sharp corners, ceiling hangers, pipes,
and construction activity.
•
•
Vertical rise length: Leave the cables on the shipping spool, and lower them
from above; do not pull the cables up from below. Use proper cable ties to
secure the cable.
General: Do not install fiber-optic cables on top of smoke detectors.
xx
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Cable management:
•
•
Leave at least 4.6 m (15 ft) of cable at each end for future growth.
Use strain reliefs to prevent the weight of the cable from damaging the
connector.
•
Review all information in this manual and in any related manuals about safely
handling fiber-optic cables.
3. Connector protection:
•
•
Insert connectors carefully to prevent damage to the connector or fiber.
Leave the connector’s protective cover in place until you are ready to make
connections.
•
•
Replace the connector’s protective cover when the connector is disconnected.
Clean the connector before making a connection. Make sure that there are no
obstructions and that keyways are aligned.
Fiber-optic Cable Handling
Observe these precautions when you handle fiber-optic cables:
•
•
Do not coil the cable to less than 96 mm (3.75 in.) in diameter.
Do not bend the cable to less than 12 mm (0.5 in.) in radius. It is most important that
a cable’s bend radius be no less than 20 times the diameter of the cable.
•
•
Do not pull on the cables; carefully place them into position.
Do not grasp the cables with pliers, grippers, or side cutters; do not attach pulling
devices to the cables or connectors.
•
Keep cables away from sharp edges or sharp protrusions that could cut or wear
through the cable; make sure that cutouts in the equipment have protective edging.
•
•
Protect the cable from extreme temperature conditions.
Install the connector’s protective cover whenever the connector is not connected.
96053
Revision L
xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Electrostatic Discharge (ESD) Damage Prevention
Anyone who handles ESD-sensitive components must be aware of the damage that ESD
can cause to electronic components and must take the proper precautions to prevent it.
Also, anyone who performs maintenance on Sun StorageTek equipment must complete
an ESD-basics course.
CAUTION:
Potential damage to equipment: Handle ESD-sensitive components only
under ESD-protected conditions. To meet this requirement, always use
the Field Service Grounding Kit (PN 4711) and always follow these ESD
precautions and procedures when you are servicing Sun StorageTek
equipment or handling ESD-sensitive components.
ESD Precautions
Always take the following general precautions when you work with ESD-sensitive
components:
•
Wear ESD protection whenever you install, remove, maintain, or repair Sun
StorageTek equipment.
•
Keep ESD-sensitive printed-circuit components in their ESD-protective packages
until you have taken all ESD-preventive steps and you are ready to install the
component.
•
•
•
Do not allow anyone to touch or handle an unprotected ESD-sensitive component
unless that person has taken all ESD precautions.
Reinstall all equipment covers and close all equipment doors after you have
completed the work.
If the grounding-kit work surface has been exposed to temperatures above 66ºC
(150ºF) or below 4.5ºC (40ºF), acclimate the work surface to room temperature
before you unroll it.
•
•
Immediately place any component that you have removed into an ESD-protective
package.
Keep the grounding-kit work surface clean.
Note: To clean the work surface, use a mild detergent and water, and make sure
that the surface is completely dry before you use it.
•
Periodically check the electrical resistance of the ground cord and the wrist-strap coil
cord.
Note: The ground cord should measure less than 1.2 MΩ, and the coil cord
should measure between 0.8 and 1.2 MΩ. Repair or replace the cords if they
no longer meet these requirements.
xxii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
ESD-Protection Procedure
Remember that each customer environment is different. Address all the customer’s
concerns before you work on any equipment.
Prepare the Work Area
1. Before you service the equipment, unfold the grounding-kit work surface completely
and place it on a convenient surface.
2. Attach one end of the ground cord to the work surface; secure the snap fastener.
Note: You will attach the free end in a later step.
3. Slip on an ESD wrist strap. Make sure that the strap is comfortable and makes
contact with the entire circumference of your wrist.
4. Snap one end of the coil cord to the wrist band.
Access the Equipment
5. Carefully open the doors to the equipment or remove the covers from the
equipment. Do not touch any internal components.
CAUTION:
Be sure that you are properly grounded before you touch any internal
components.
6. Attach the free end of the coil cord to the most appropriate place:
a. If you are working on components from a small piece of equipment, attach the
free end of the coil cord to the grounding-kit work surface. In addition, be sure
that you touch an unpainted metal surface on the equipment before you touch an
internal component.
b. If you are working on components from a large piece of equipment, attach the
free end of the coil cord to a grounding jack or to an unpainted metal surface
inside the equipment.
Replace Components
7. Remove the defective component and place it on the work surface.
8. Remove the replacement component from its ESD-protective package, and install
the component in the equipment.
9. Place the defective component in the ESD-protective package.
96053
Revision L
xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean Up
10. Disconnect the ground cords from the equipment.
11. Reinstall all equipment covers and close all equipment doors.
12. Disconnect the coil cord from your wrist, and, if necessary, disconnect the ground
cord from the work surface.
13. Properly store the work surface and the other Field Service Grounding Kit items.
xxiv
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Seguridad
Las siguientes páginas describen prácticas habituales sobre seguridad eléctrica,
ergonomía, instalación en bastidor, fibras ópticas y descargas electrostáticas.
■ Precauciones de seguridad
ADVERTENCIA:
Posibles lesiones: la seguridad durante el trabajo es importante; por
ello, atienda a las siguientes precauciones de seguridad mientras esté
realizando alguna actividad de mantenimiento. El incumplimiento de
dichas precauciones puede conllevar graves lesiones.
Antes de realizar cualquier tarea en equipos eléctricos conectados,
quítese las joyas y accesorios conductores de electricidad, como relojes
y anillos.
•
Evite las descargas eléctricas. Tenga cuidado al trabajar en la proximidades de
conectores y alimentaciones eléctricas.
•
Antes de extraer unidad sustituible in situ u otro componente, apague el equipo y
desconéctelo de la red eléctrica. Recuerde que, incluso si están apagados, en algunas
áreas pueden quedar tensiones peligrosas.
•
•
Ponga a tierra todos los equipos de prueba y herramientas eléctricas.
Para levantar objetos, consulte la información de “Técnicas de levantamiento de
objetos” (véase a continuación).
•
•
No quite, corte ni cambie de lugar indiscriminadamente las baldosas. Antes de
manipular baldosas, asegúrese de conocer el entorno del cliente y de recibir su
autorización. Recuerde que cada situación es diferente.
Aplique las prácticas adecuadas de limpieza en el área del equipo para prevenir
incendios y accidentes.
Nota: Entre los factores importantes que deben tenerse en cuenta es la presencia de gas
Halón®, detectores de humo subterráneos y cables conductores a otros equipos
instalados en las proximidades.
96053
Revision L
xxv
Download from Www.Somanuals.com. All Manuals Search And Download.
Técnicas de levantamiento de objetos
El levantar equipos o componentes, independientemente de su peso o tamaño, puede
provocar serias lesiones lumbares. Siguiendo estas directrices podrá reducir los riesgos
de lesiones.
•
No incline el cuerpo para levantar o bajar algo. Esta posición supone una tensión
extrema para la espalda, en especial al levantar o transportar objetos. En lugar de
inclinarse, efectúe dos movimientos: primero levante el componente y, a
continuación, utilice los pies para girar el cuerpo.
•
•
Planifique el levantamiento: primero examine el objeto y, a continuación, determine
cómo lo levantará y dónde lo colocará.
Seleccione la técnica de levantamiento adecuada. Examine el peso y tamaño del
objeto, su ubicación y frecuencia y dirección en que vaya a levantarlo. La planificación
debe hacerse de tal modo que se eviten posturas incómodas. Determine si son
necesarios accesorios para la manipulación de materiales.
•
Separe bien las piernas y coloque una ligeramente detrás de la otra. Mantenga la
espalda recta, porque incluso pesos ligeros pueden incrementar significativamente
la presión sobre la espina dorsal al inclinarse hacia adelante.
•
•
•
En la medida de lo posible, sostenga la carga con toda la mano, y utilice ambas
manos.
Transporte los objetos a la altura del codo y próximos a su cuerpo. Cuanto más lejos
tenga que transportar un objeto, más presión aplicará sobre la zona lumbar.
Levante el objeto haciendo fuerza con las piernas, y no con la espalda. Los músculos
de las piernas se cuentan entre los más fuertes del cuerpo. Al acuclillarse y levantar un
peso con las piernas, tendrá mayor tolerancia al peso.
•
Alterne estas tareas con otras menos pesadas para los mismos músculos. De este
modo, los músculos dispondrán de un cierto tiempo de recuperación.
Seguridad de hombros, codos, muñecas y manos
Siga estas instrucciones para reducir al mínimo las posibilidades de lesionarse los
hombros, codos, muñecas y manos.
•
•
•
Trabaje dentro de su zona de seguridad, el área entre el nivel de los hombros y el nivel
de los nudillos. Trabajando o levantando objetos dentro de esta área se expondrá a
menos probabilidades de lesiones.
Mantenga los codos inclinados para mantener las cargas próximas a su cuerpo y
reducir la fuerza necesaria para realizar la tarea. Con esta postura, aplicará menos
peso y presión sobre los hombros.
Asegúrese de mantener las muñecas rectas. Evite doblarlas, extenderlas o torcerlas
durante períodos de tiempo prolongados.
xxvi
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
•
No levante cargas grandes o pesadas con el puño cerrado, porque el modo de
levantarlas también afecta a los tendones de la mano. Al tomar un objeto entre el
pulgar y los dedos se aplica mucha tensión a las manos y tendones de las muñecas.
Utilice ambas manos alternativamente, para permitir que descansen.
■ Seguridad y precauciones del bastidor
ADVERTENCIA:
Posibilidad de lesiones físicas:
•
Peligro de levantamiento: La biblioteca pesa 44,45 kg (98 lb), a lo que
hay que añadir el peso de las unidades. Para levantar la biblioteca y
colocarla en su posición se requieren como mínimo dos personas.
Antes de poner manos a la obra, asegúrese de leer la información
presentada en “Técnicas de levantamiento de objetos” en la
•
Al colocar otros equipos en el bastidor, considere también el peso
total de la biblioteca. Para evitar un desequilibrio de la carga,
coloque los equipos más pesados abajo y los más ligeros arriba.
De lo contrario, el bastidor podría desestabilizarse y caerse.
Al instalar la biblioteca en el bastidor, adopte las siguientes precauciones de seguridad:
•
Si el bastidor tiene puertas delanteras o traseras, no permita que las puertas interfieran
con la ventilación de la biblioteca. La temperatura ambiente en el interior del bastidor
no debe ser superior a la temperatura de servicio recomendada de la biblioteca.
La temperatura ambiente máxima del interior del bastidor es de 40 °C (104 °F).
•
•
Asegúrese de que las puertas del bastidor permitan el acceso adecuado a la biblioteca.
Asegúrese de que la combinación de la biblioteca con otros equipos instalados en el
bastidor no provoque situaciones de sobretensión, tanto si el equipo está conectado
directamente al circuito derivado o a una regleta de distribución.
•
Asegúrese de que todos los equipos del bastidor dispongan de una puesta a tierra
fiable, tanto si el equipo está directamente conectado al circuito derivado o a una
regleta de distribución
Nota: La puesta a tierra de la biblioteca se conecta a través de la patilla de puesta
a tierra del enchufe.
■ Seguridad de fibras ópticas
ADVERTENCIA:
Riesgo para la vista. Nunca mire directamente el interior de un cable de
fibra óptica, un conector de fibra óptica o un módulo transceptor de
láser. Los niveles de potencia del láser pueden conllevar situaciones de
riesgo, susceptibles de lesionar la vista.
96053
Revision L
xxvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Tenga especial cuidado al utilizar instrumentos ópticos con estos
equipos. Dichos instrumentos pueden incrementar las probabilidades
de lesiones oculares.
Los transceptores de láser de los equipos de fibra óptica pueden suponer un peligro
para la seguridad física. Asegúrese de que toda persona que trabaje con estos equipos de
Sun StorageTek entienda los peligros y siga los procedimientos de seguridad. Asegúrese
de que todos los puertos ópticos de los módulos transceptores de láser estén terminados
con un conector óptico, una cubierta o un tapón de protección contra el polvo.
Todas las interfaces de fibra óptica de estos equipos de canal de fibra de Sun StorageTek
contienen un transceptor de láser, categorizado como Producto láser de Clase 1. Cada
transceptor láser tiene una salida de menos de 70 μW y una longitud de onda de 850 nm.
Los productos de láser de clase 1 de Sun StorageTek cumplen las normas EN60825-
1(+A-11) y las secciones 21 CFR 1040.10 y 1040.11 de las normas de la Administración
para la Calidad de Alimentos y Medicamentos (FDA).
Las siguientes traducciones están dirigidas a usuarios de Finlandia y Suecia que deseen
identificar la categoría y clasificación de seguridad de los dispositivos láser:
LÁSER DE CLASE 1
LUOKAN 1 LASERLAITE
KLASSE 1 LASER APPARAT
Etiqueta del producto láser
De conformidad con las normas de seguridad, cada producto de canal de fibra de Sun
StorageTek lleva una etiqueta que identifica la clase de láser del producto, y el lugar y
fecha de fabricación. Esta etiqueta aparece sobre la unidad de cinta de canal de fibra, así
como en las proximidades de los conectores de las bibliotecas de cintas de canal de fibra.
A continuación puede verse una copia de dicha etiqueta:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A LASER DE CLASSE 1
CUMPLE LAS NORMAS 21 CFR 1040.10 Y 1040.11
xxviii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Instalación de cables de fibra óptica
Para instalar cables de fibra óptica, efectúe este procedimiento:
1. Tendido del cable:
•
Tarima: Los cables de fibra óptica pueden instalarse debajo de tarimas.
Al tenderlos, manténgalos apartados de cualquier obstrucción, como por
ejemplo otros cables o equipos.
•
Escalerilla portacables o canaleta de cables: Sitúe los cables en su
posición. No tire de ellos a través de la escalerilla portacables. Al tender los
cables, manténgalos apartados de esquinas afiladas, colgadores de techo,
conductos, tuberías y actividades de construcción.
•
•
Longitud de elevación vertical: Deje los cables en la bobina original y
bájelos desde arriba. No tire de ellos desde abajo. Utilice los fijadores adecuados
para inmovilizarlos.
General: No instale cables de fibra óptica encima de detectores de humo:
2. Instalación de los cables:
•
•
•
Deje como mínimo 4,6 m (15 pies) de cable en cada extremo, en previsión
de futuras extensiones.
Utilice protectores contra tirones para evitar que el peso del cable dañe el
conector.
Repase en el presente manual, así como de manuales afines, toda la información
relativa a la manipulación segura de cables de fibra óptica.
3. Protección de los conectores:
•
•
Inserte los conectores con todo cuidado para evitar dañar éstos o la fibra.
No quite la cubierta de protección del conector hasta que esté preparado para
realizar las conexiones.
•
•
Al desconectar el conector, vuelva a colocar la cubierta de protección.
Antes de realizar una conexión, limpie el conector. Asegúrese de que no haya
obstrucciones y de que las ranuras de chavetas estén alineadas.
Manipulación de cables de fibra óptica
Al manipular cables de fibra óptica, tenga en cuenta las siguientes precauciones:
•
•
No enrolle el cable a menos de 96 mm (3,75") de diámetro.
No curve el cable a menos de 12 mm (0,5") de radio. Sun recomienda que el radio de
curvatura de un cable no sea inferior a 20 veces el diámetro del cable.
•
No tire de los cables: colóquelos con cuidado en su posición.
96053
Revision L
xxix
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
No aferre los cables con alicates, pinzas ni fresas. No una los cables ni los conectores
a dispositivos de tracción.
Mantenga los cables apartados de bordes y salientes afilados que pudieran cortarlos
o desgastarlos. Asegúrese de que los orificios del equipo dispongan de bordes
protectores.
•
•
Proteja los cables contra temperaturas extremas.
En toda ocasión en que el conector no esté conectado, colóquele su cubierta de
protección.
■ Prevención de daños por descargas
electrostáticas (DES)
Quienes manipulan componentes sensibles a las descargas electrostáticas (DES) deben
ser conscientes de los daños que éstas pueden provocar en los componentes electrónicos,
con el objeto de adoptar las precauciones adecuadas para evitarlas. Asimismo, las
personas que realicen tareas de mantenimiento en equipos de Sun StorageTek deben
pasar un curso de fundamentos de las descargas electrostáticas.
PRECAUCIÓN:
Posibles daños a los equipos: Manipule los componentes sensibles a
las descargas electrostáticas sólo en las condiciones de protección
adecuadas. Para cumplir este requisito, utilice siempre el Kit de puesta a
tierra del servicio de campo (NP 4711) y cumpla en todo momento estas
precauciones y procedimientos al realizar tareas de mantenimiento
o servicio técnico de equipos de Sun StorageTek, así como al manipular
componentes sensibles a las descargas electrostáticas.
Precauciones contra descargas electrostáticas
Al trabajar con componentes sensibles a las descargas electrostáticas (DES), adopte
siempre las siguientes precauciones generales:
•
Utilice protección contra descargas electrostáticas a realizar tareas de instalación,
desinstalación, mantenimiento o reparación de equipos de Sun StorageTek.
•
Mantenga los circuitos impresos sensibles a las descargas electrostáticas dentro
de sus embalajes de protección hasta haber adoptado las medidas de prevención
adecuadas y esté preparado para instalar el componente.
•
No permita que nadie toque o manipule un componente sensible a las descargas
electrostáticas no protegido, salvo que dicha persona haya adoptado las precauciones
pertinentes.
xxx
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Una vez concluido el trabajo, vuelva a colocar todas las cubiertas del equipo y cierre
todas las puertas.
Si la superficie de trabajo del kit de puesta a tierra ha estado sometida a temperaturas
superiores a los 66 ºC (150 ºF) o inferiores a los 4,5 ºC (40 ºF), deje que la superficie
se aclimate a la temperatura ambiente antes de desenrollarla.
•
•
Coloque inmediatamente sobre esta superficie todo componente que haya retirado
de su embalaje de protección contra descargas electrostáticas.
Mantenga limpia la superficie de trabajo del kit de puesta a tierra.
Nota: Para limpiarla, utilice agua y un detergente suave, asegurándose de que esté
completamente seca antes de utilizarla.
•
Compruebe periódicamente la resistencia eléctrica del cable de puesta a tierra y del
cable en espiral de la muñequera.
Nota: Al medir la resistencia del cable de puesta a tierra, debe ser inferior a 1,2
MΩ,; la del cable en espiral debe situarse entre 0,8 y 1,2 MΩ. Repare o
sustituya los cables si no cumplen estos requisitos.
Procedimiento de protección contra descargas
electrostáticas
Recuerde que cada entorno de cliente es diferente. Responda a todas las dudas e
inquietudes del cliente antes de proceder a trabajar en un equipo.
Prepare el área de trabajo
1. Antes de reparar el equipo, desenrolle completamente la superficie de trabajo del kit
de puesta a tierra y colóquela sobre una superficie adecuada.
2. Conecte un extremo del cable de puesta a tierra a la superficie de trabajo y ajuste el
broche de presión.
Nota: El otro extremo se conectará posteriormente.
3. Colóquese una muñequera antiestática. Asegúrese de que le resulte cómoda y que
haga contacto con toda la circunferencia de la muñeca.
4. Conecte a la muñequera un extremo del cable en espiral.
96053
Revision L
xxxi
Download from Www.Somanuals.com. All Manuals Search And Download.
Acceda al equipo
5. Con todo cuidado, abra las puertas o retire las cubiertas del equipo. No toque ningún
componente interno.
PRECAUCIÓN:
Antes de tocar cualquier componente interno, asegúrese de estar
correctamente conectado a tierra.
6. Conecte el extremo libre del cable en espiral al lugar más adecuado:
a. Si está trabajando con componentes de un equipo de pequeñas dimensiones,
conecte el extremo libre del cable a la superficie de trabajo del kit de puesta
a tierra. Asimismo, asegúrese de tocar una superficie metálica no pintada del
equipo antes de tocar cualquier componente interno.
b. Si está trabajando con componentes de un equipo de amplias dimensiones,
conecte el extremo libre del cable en espiral a un conector de puesta a tierra
o a una superficie metálica no pintada del interior del equipo.
Sustituya los componentes
7. Sustituya el componente defectuoso y colóquelo sobre la superficie de trabajo.
8. Extraiga el componente de recambio de su embalaje de protección contra descargas
eléctricas e instálelo en el equipo.
9. Coloque el componente defectuoso dentro del embalaje de protección.
Limpie
10. Desconecte los cables de puesta a tierra del equipo.
11. Vuelva a instalar todas las cubiertas y cierre todas las puertas del equipo.
12. Desconecte el cable en espiral de la muñeca. Si fuese necesario, desconecte el cable
de puesta a tierra de la superficie de trabajo.
13. Pliegue correctamente la superficie de trabajo, y guárdela. Guarde también los demás
componentes del Kit de puesta a tierra del servicio de campo.
xxxii
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
1
This chapter tells you how to install the L40 Tape Library. Two methods are available:
•
•
“Quick Installation Procedure” for users who have installed other L40 Tape Libraries
“Standard Installation Procedure” on page 1-4 for first-time installers who want help
with each step of the process
You might need to ask your system administrator for some of the configuration
information, such as the network entries.
cables.
■ Quick Installation Procedure
If you are experienced with computer equipment and want to install this library with the
minimum number of steps, use the following procedure. If you encounter problems,
WARNING:
before beginning. Use at least two people and a mechanical device to lift
and position the library. The library weighs 44.45 kg (98 lb) plus the
weight of the drives.
ADVERTENCIA:
La seguridad es lo primero: Antes de poner manos a la obra, asegúrese
levantar la biblioteca y colocarla en su posición se requieren como
mínimo dos personas. La biblioteca pesa 44,45 kg (98 lb), a lo que hay
que añadir el peso de las unidades.
Note: Rack installation requires special procedures.
Save all the packing material in case you want to relocate or return the library in
the future.
1. Remove the library from its shipping container and place the library on a firm,
horizontal surface.
2. Obtain the door key from the accessory container, and unlock and open the front
door.
96053
Revision L
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Installation Procedure
3. Remove the packing cushion and foam.
4. Visually inspect the library and drives, using a flashlight if necessary:
CAUTION:
Possible component damage: Make sure you follow the ESD procedure
5. Obtain the personality module from the bag taped to the power supply handle and
insert it into its connector at the rear of the library. The library will not initialize properly
unless the personality module is installed.
•
•
A 20-cell version uses part 31363270x.
A 40-cell version uses part 31363300x.
6. If your library is a 20-cell version, attach the cell barrier clip
identifies the cells that you may use for your data cartridges.
7. Connect one end of the power cable into the rear of the library.
8. Connect the other end of the power cable into the wall socket.
9. Power-on the library and drives. The library will begin its initialization routine.
10. When initialization is complete, use the operator panel to configure the library and
drives.
Note: Refer to the user’s guide for any field values that you do not understand.
11. When the configuration is complete, power-off the library and drives.
12. Connect the SCSI cables to the rear of the library.
13. Attach the HVD or LVD label to the SCSI cable connector.
14. Terminate the last drive in the string:
•
•
HVD uses terminator part 10187075.
LVD/SE uses terminator part 10148031.
Note: If your library includes an optional Fibre Channel router, attach cables according
15. Power-on the library to activate the firmware.
16. Wait for the library to complete initialization.
17. Press the MENU button.
1-2
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Installation Procedure
18. Press the SELECT button.
The >sign appears to the left of Door Operations. The DOOR MENU:
Push Select to Prepare Library for Opening Doormessage
appears.
19. Press the SELECT button.
CAUTION:
Possible hand damage: Always wait for the operator panel to display the
OK To Open Doormessage before opening the door. This ensures that
the hand assembly is safely seated.
20. Insert the key into the lock, and unlock and open the door.
21. Insert the labeled cartridges into the library.
Make sure that the cartridge hub is down and the volume label is facing the robot.
22. Close and lock the door, and remove the key.
The library will initialize and audit the cartridges.
23. Configure your tape management software at the console.
24. Place the library online.
26. Make a copy of the table and give it to the customer. The customer will refer to it
when making a service call or ordering features and upgrades.
96053
Revision L
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
■ Standard Installation Procedure
The procedure for the standard installation of the library takes you through each step of
the installation process.
Check off the tasks in this list as you complete them:
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
1-4
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Preparing for the Installation
In general, for a successful installation you should be familiar with:
•
•
•
•
•
SCSI principles (bus termination, terminating power, addressing)
The SCSI cable plan for your installation
The SCSI addresses (IDs) already in use by your system
The SCSI IDs chosen for the devices to be installed (library and drives)
Fibre Channel principles (termination, cabling, addressing) if your library includes an
optional Fibre Channel router
Unpacking the Library
Note: Save all the packing material in case you want to relocate or return the library in
the future.
1. Cut any packing tape, bands, and seals, and remove the outer container.
2. Remove the container locks.
3. Remove the container cap.
4. Remove the accessory container.
5. Remove the sleeve.
6. Remove the top cushion.
7. Remove the plastic bag.
8. Remove the front and rear rail of the bottom cushion. Do not remove the library from the
pallet.
9. Obtain the door key, part 419712101, from the accessory container, and unlock and
open the door.
96053
Revision L
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Figure 1-1. Unpacking the Library (L201_158)
1. Outer Container
7. Bar code label, used for repacking
2. Container cap
3. Logo label, used for repacking
8. Top cusion
9. Plastic bag
4. Container locks (Hold so the protruding part is 10. Library
on top. Squeeze the ears and lift the locks to
secure them into the openings.)
5. Accessory container
11. Internal bracing items
12. Bottom cushion
13. Front and rear rail
14. Pallet
6. Sleeve
10. Cut the tie wraps and remove the packing cushion from the Z shaft.
1. Tie Wraps
2. Packing cushion around the rear Z shaft
3. Z carriage
4. Hand foam
11. Carefully raise the Z carriage and remove the foam securing the hand assembly.
96053
Revision L
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Inspecting the Library and Drives
Visually inspect the library and drives, using a flashlight if necessary:
1. Check the library’s exterior and interior for any obvious physical damage or loose
parts.
2. Make sure that the cables and accessories you require are present. Refer to your
shipping bill. Some items might be shipped in a separate package.
____ SCSI cables
____ SCSI terminators
____ SCSI adapters
____ Fibre Channel cables
____ AC power cable
____ Cartridges and labels
____ Personality module (in a bag taped to the power supply handle)
3. Report any damaged, missing, or incorrect items to your sales representative.
Preparing the Installation Location
Prepare the installation location:
1. Make sure that the location is clean, dry, level, and adequately ventilated.
2. Allow sufficient space to service the library from the front, right side, and rear. Each
of these areas should have a service clearance of 610 mm (2 ft).
3. Make sure that the AC power outlet is near the library and is easily accessible to the
library’s power cable.
4. If you are installing the library in a 483-mm (19-in.) standard-width rack, you must
have either brackets or a tray measuring at least 711 mm (28 in.) deep. Make sure that
the brackets or tray is installed within the rack before you install the library.
meets the required dimensions and weight.
1-8
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Positioning the Library
The library can be ordered for either desktop or rack installation.
Desktop Installation
WARNING:
Possible personal injury: Check the path to the intended location and
clear it of obstructions before you move the library. Use at least two
people and a mechanical device to lift and position the library. The
library weighs 44.45 kg (98 lb) plus the weight of the drives. Depending
upon the drive type, each drive weighs between 5.0 kg (11 lb) and 5.5 kg
(12 lb).
ADVERTENCIA:
Posibilidad de lesiones físicas: Antes de mover la biblioteca, verifique el
trayecto hasta la ubicación de instalación prevista y retire cualquier
obstáculo. Para levantar la biblioteca y colocarla en su posición se
requieren como mínimo dos personas. La biblioteca pesa 44,45 kg (98
lb), a lo que hay que añadir el peso de las unidades. En función del tipo
de unidad, cada unidad pesa entre 5,0 kg (11 lb) y 5,5 kg (12 lb).
CAUTION:
Equipment damage: Do not grip the library by the power supply handles
or by the fans.
To install the desktop library:
1. Place the library on any sturdy desk or table within cabling distance to your client-
server computer.
2. Install the drive trays, if they were not shipped with the library.
Rack Installation
Use a standard 483-mm (19-in.) rack with 10 rack units of space to accommodate the
library, which sits on brackets or a tray provided by the customer. The library is secured
to the rack with screws and nut clips to prevent anyone from pulling the library off the
rack.
The rack can have a rear door. The door must extend at least 102 mm (4 in.) beyond the
library to allow proper air flow for the library’s cooling fans and for cable routing. The
maximum rack air ambient temperature is 40ºC (104ºF).
To allow easy access to the CAP and operator panel, the rack should not have a front
door. If you install a front door, make sure that the door provides proper ventilation.
96053
Revision L
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
The library uses the power cable’s ground point for its earth-ground connection. All
electrical connections, either directly to the wall or to a power strip in the rack, must be
properly grounded. Consider proper electrical circuit and power strip overload
protection.
Note: The rack can be ordered from Sun StorageTek or from another vendor. The
StorageTek conversion bill number for the black rack is YXL20/40/80-SHELF.
To install the library in a rack:
1. Install the brackets or tray onto the rack if not previously done. The tray must be at
least 749.3 mm (29.5 in.) deep.
WARNING:
Possible personal injury: Check the path to the intended location and
clear it of obstructions before you move the library. Use at least two
people and a mechanical device to lift and position the library. The
library weighs 44.45 kg (98 lb) plus the weight of the drives. Depending
upon the drive type, each drive weighs between 5.0 kg (11 lb) and 5.5 kg
(12 lb).
ADVERTENCIA:
Posibilidad de lesiones físicas: Antes de mover la biblioteca, verifique el
trayecto hasta la ubicación de instalación prevista y retire cualquier
obstáculo. Para levantar la biblioteca y colocarla en su posición se
requieren como mínimo dos personas. La biblioteca pesa 44,45 kg (98
lb), a lo que hay que añadir el peso de las unidades. En función del tipo
de unidad, cada unidad pesa entre 5,0 kg (11 lb) y 5,5 kg (12 lb).
WARNING:
Tip hazard: When installing the library, be careful to keep the rack from
tipping over.
ADVERTENCIA:
Peligro de vuelco. Al instalar la biblioteca, tenga cuidado de que el
bastidor no se vuelque.
CAUTION:
Equipment damage: Do not grip the library by the power supply handles
or by the fans.
2. Slide the library onto the previously installed supporting brackets or tray.
Note: You must remove the front door and decorative cover over the operator panel to
access the holes in the library flanges.
3. Insert the key into the lock on the door, and unlock and open the door.
4. Hold the door firmly with your left hand and remove the bottom hinge pin, then the
top hinge pin.
1-10
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
1. Hinge pin (2)
5. Set the door aside.
6. Remove the right decorative cover over the operator panel by grasping the top of the
cover and gently pulling it away from the operator panel.
1. Cover
2. Cover snap pins
7. Measure and note the distances from the bottom of the library flanges to the
mounting holes near the four corners of the front of the library frame. Note that the
distances for the left and right flange hole spaces are different.
8. Using these distances, install the four nut clips into the rack so that their locations
match the hole locations from the previous step.
9. Secure the library to the rack with four screws through the rack to the screw nut clips
on the rear of the rack.
96053
Revision L
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
1. Screw (4)
10. Attach the cover over the operator panel.
11. Attach the door with the two hinge pins, inserting the top pin first.
Choosing SCSI HVD or LVD
Your library interface is hardware configured as either high voltage differential (HVD) or
low voltage differential (LVD). The HVD interface allows longer cable lengths, but
throughput is slower than LVD. The LVD interface restricts cable lengths, but provides
faster throughput.
CAUTION:
Potential equipment damage: Do not mix LVD and HVD operation on the
same bus.
SCSI Cable Restrictions
The library and drives accept only SCSI Type-3 connectors. If you use SCSI Type-1 or -2
connectors, you must use a SCSI Type-1- or SCSI Type-2-to-SCSI Type-3 adapter.
Note: If you are connecting the library or drives to an LVD SCSI bus, the cable can be
no longer than 12 m (39.4 ft).
Each interface requires a unique terminator.
The following table lists restrictions for SCSI connections.
1-12
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Table 1-1. SCSI Cable Length Restrictions
Application
Length Restriction
Single-ended
Stub length: 102 mm (4 in.)
5 to 10 MB/s data transfer rate: 3 m (10 ft)
1 to 5 MB/s data transfer rate: 6 m (20 ft)
High voltage
differential
Stub length: 203 mm (8 in.)
1 to 40 MB/s data transfer rate: 25 m (82 ft)
Low voltage
differential
Stub length: 102 mm (4 in.)
1 to 80 MB/s data transfer rate: 12 m (39.37 ft)
Host Bus Adapter Requirements
The host bus adapter (HBA) in your server must match the library and drive’s SCSI bus
type. If the interface to the library is HVD, the server must contain an HVD-compatible
HBA; if the interface to the library is LVD, the server must contain an LVD-compatible
HBA.
SCSI Device/Bus Type Issues
The following table lists the possible issues you could encounter if you mix interfaces on
the same bus.
Table 1-2. SCSI Device/Bus Types: Issues
If you plug a . . .
Into . . .
The result is . . .
Single-ended bus
LVD bus
Proper connection
Single-ended device
Single-ended mode
Operation disabled
Single-ended mode
Proper connection
HVD bus
Single-ended bus
LVD bus
Low voltage
differential device
HVD
Potential damage/disabled device
Disabled device
Single-ended bus
LVD bus
High voltage
differential device
Potential damage/disabled device
Proper connection
HVD bus
96053
Revision L
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Installing the External Fibre Channel Router
To install the optional external Fibre Channel router, refer to StorageNet 3300 Fibre
Channel Router User Manual, Chapter 2.
If installing an external fibre channel router to replace an internal fibre channel router
card, remove the internal fibre channel router card. Refer to the L40 Tape Library Service
Manual, PN 96026.
Connecting the External SCSI Cables
Note: You can connect the library and drives to the same bus (on bus) or to separate
buses (off bus). However, for the on bus configuration, a bus reset will affect all
devices on the bus. Library availability can be improved by ensuring that the
library is on a separate bus from the drives.
You should be familiar with SCSI principles to correctly cable your system.
The library supports the use of:
•
•
•
Digital linear tape (DLT) 7000E/8000 drives on an HVD interface
DLT 8000 drives on an LVD interface
Ultrium linear tape open (LTO) drives on an LVD interface (native) or on an HVD
interface (with an optional converter card that is on the drive tray assembly when
ordered as HVD from Storage Technology Corporation)
•
DLT1 drives on an LVD interface (native) or on an HVD interface (with optional
converter card)
To attach SCSI cables:
1. Attach a SCSI daisy-chain cable to one rear SCSI port on the drive. These cables
should be at least 300 mm (11.81 in.) if connecting from the LLC card to the top
drive slot, or 600 mm (1.97 ft) if connecting from the LLC card to the bottom drive
slot. If you have an internal Fibre Channel router installed, use the 600 mm (1.97 ft.)
cable to reach from the LLC card to the drive slots.
2. Connect the client-server cable to the library.
Note: Make sure you properly set the SCSI IDs for the drives and library, or you might
stop activity on the SCSI bus. You will set the IDs when you configure the
library and drives.
3. Install the provided terminator on the remaining SCSI port of the lowest drive that is
installed, and on the client server computer, if required:
•
•
HVD uses terminator part 10187075.
LVD/SE uses terminator part 10148031.
1-14
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
You can vary this cabling arrangement depending on how your system is configured. For
example, you can attach one of the drives to a different bus, in which case that drive
would have its own SCSI terminator.
1. Client-server cable
2. SCSI cable
3. SCSI terminator
96053
Revision L
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Connecting Fiber and SCSI Cables
For libraries with an optional Fibre Channel router, follow the cable routing shown in
following two figures The first figure shows cable routing for the library, four drives, and
internal router.
The second figure shows a detail of cable routing to the SN3300 external router.
1. Fiber cables to/from host
2. Four 300 mm (11.81 in.) LVD SCSI cables
3. One 600 mm (1.97 ft) LVD SCSI cable
4. Two SCSI terminators
1-16
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
1. Fiber cables to/from host
2. One of four 300 mm (11.81 in.) LVD SCSI cables
3. Power cable
96053
Revision L
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Attaching the Personality Module
The personality module is a connector that stores the library cell capacity information.
The module stores a capacity of either 20 or 40 cells. The library does not operate
properly unless an authorized module is attached to the rear of the EM.
Attach the module before powering-on the library for proper initialization. Only remove the module
when installing an upgrade conversion bill or replacing the library.
CAUTION:
Possible component damage: Make sure you follow the ESD procedure
connecting the personality module.
The personality module is in a bag taped to the power supply handle. Remove the
personality module and attach it to its connector:
•
•
A 20-cell version uses part 31363270x.
A 40-cell version uses part 31363300x.
1. Personality module
1-18
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Attaching the Cell Barrier Clip
If your library is a 20-cell version, the tape management software only recognizes the data
cells that are in Column 0 and the top nine cells of Column 1. To remind the operator to
not place data cartridges into the other cells, attach the cell barrier clip, as shown in the
following figure.
Use the PERS MODULE Menuon the operator panel to determine your library’s cell
capacity.
Figure 1-2. Attaching the Cell Barrier Clip (L201_124)
1. Cell barrier clip for 20-cell version
96053
Revision L
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Inserting the Cartridges
Depending on the version and configuration of your library, some storage cells cannot be
CAUTION:
Inserting the cartridges correctly is critical for library operation. If you
do not orient the cartridges correctly or do not insert them all the way
into the storage cells, the library might fail, and the operator panel might
display an error message. Make sure you insert the cartridge inside the
correct way to insert cartridges into storage cells.
Do not place a white cartridge into cell 1022d (see Figure 1-3 on
page 1-21), or you will cause an initialization failure.
Check the cartridges to make sure that they are correctly labeled, as described in the user’s
guide.
The media check feature, if enabled, ensures that there are no unreadable, unlabeled, or
improperly placed cartridges. If the robot cannot grab one of these cartridges, the library
status will be “not ready.”
Note: You do not have to insert a cartridge into every storage cell. The library
automatically audits cartridges and empty cells as part of its initialization routine.
Insert as many cartridges into the library as you want and as your configuration allows,
making sure you seat them all the way into the storage cells.
1-20
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Figure 1-3. Determining the Valid Storage Cells (L201_038)
1. Drive Slot 3
2. Drive Slot 2
3. Drive Slot 1
4. Drive Slot 0
1. Column 0
2. Column 1
3. Column 2
4. Column 3
5. CAP (two cells)
Note: In a 40-cell capacity library, if Auto Clean is not enabled, the cleaning cartridge cell can
be used for a data cartridge, for a total of 41 data cells.
Legend:
•
•
Use Columns 0 and 1 white cells for the 20-cell configuration.
Use Columns 0 and 1 white cells and Columns 2 and 3 gray cells for the 40-cell
configuration.
•
•
Use the black cell above the CAP for a cleaning cartridge if Auto Clean is enabled.
The small, black rectangles are targets.
96053
Revision L
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Drive Compatibility Issues
Refer to your drive publications and the vendor Web sites for a detailed discussion of
drives and cartridges.
The library supports the following drives:
•
Ultrium Linear Tape-Open (LTO) drives
LTO technology was developed by IBM, Hewlett-Packard, and Seagate to provide a
clear and viable choice in an increasingly complex array of tape storage options. LTO
is an “open format’ technology, which means that users will have multiple sources of
product and media. The open nature of LTO technology also provides a means of
enabling compatibility among different vendor’s offerings.
-
-
-
-
Hewlett-Packard’s LTO 1, LTO 2, and LTO 3
IBM’s LTO 1, LTO 2, and LTO 3
Quantum’s (Certance) LTO 2 and LTO 3
Seagate LTO 1 and LTO 2
•
Digital Linear Tape (DLT) drives:
•
Quantum Corporation’s DLT 7000E, DLT 8000, and Super DLT 220, 320 and
600
•
Benchmark Storage Innovations, Inc’s DLT1
You may mix drive types within a library, but please observe the following cautions and
tables:
CAUTION:
Possible data corruption: Do not mix DLT 7000 and DLT 8000 drives in
the same library. If a DLT 7000 cartridge is inserted into a DLT 8000 drive,
the tape can be read and written on in 7000 mode. If a DLT 8000 cartridge
is inserted into a DLT 7000 drive and a read command is issued, the
drive will indicate Medium Error/Calibration Error (03/8000). If a write
command is issued at load point, as with most drives, the drive will write
over any data present.
CAUTION:
Data loss: Do not mount SDLT 320-formatted cartridges into SDLT 220
drives. An SDLT 220 drive will overwrite the 320 data. To avoid this,
carefully manage the locations of the cartridges within your library, and
designate the correct drive type for your read/write operations.
Do not mix LVD and HVD operations on the same bus.
DLT1 drives use only DLTtape IV cartridges, and can read—but not write to—
DLTtape IV cartridges formatted by DLT 4000 drives.
DLT1 drives use their own cleaning cartridge, part 100099401. Do not use this
cartridge in DLT drives.
96053
Revision L
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Table 1-3. LTO Drive Backward Readability
LTO Gen 2 Drive
Read and write
Read and write
No action
LTO Gen 3 Drive
Read only
LTO 1 media
LTO 2 media
LTO 3 media
Read and write
Read and write
Table 1-4. SCSI Device/Bus Types: Issues
If you plug a . . .
Into . . .
The result is . . .
Proper connection
Single-ended mode
Operation disabled
Single-ended mode
Proper connection
Single-ended bus
LVD bus
Single-ended device
HVD bus
Single-ended bus
LVD bus
Low voltage
differential device
HVD
Potential damage/disabled device
Disabled device
Single-ended bus
LVD bus
High voltage
differential device
Potential damage/disabled device
Proper connection
HVD bus
The drive interfaces are SCSI high voltage differential (HVD) or SCSI low voltage
differential (LVD). The HVD interface allows longer cable lengths, but throughput is
slower than with the LVD interface. The LVD interface restricts cable lengths, but
provides faster throughput.
The following table shows the types of drives and the interfaces that are supported.
1-24
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Table 1-5. Compatible Drives and Interfaces
Interface
Sustained Native
Drive Name
Transfer Rate
HVD1
LVD2
DLT 8000
SDLT 220
SDLT 320
SDLT 600
6.0 MB/s
11 MB/s
16 MB/s
36 MB/s
16 MB/s
34 MB/s
68 MB/s
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD 80MB/s, SE
40MB/s
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD 80MB/s, SE
40MB/s
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD 80MB/s, SE
40MB/s
N/A
Ultra-3 SCSI LVD 160
MB/s, SE 40 MB/s
Seagate/Certance
Ultrium 1 LTO5
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD 80 MB/s, SE 40
MB/s
Seagate/Certance
Ultrium 2 LTO5
N/A
Ultra-2 SCSI LVD 80 MB/s
Seagate/Certance
Ultrium 3 LTO5
N/A
Ultra-3 SCSI Ultra-160 LVD
160MB/s
IBM Ultrium 1 LTO 15 MB/s
IBM Ultrium 2 LTO 35 MB/s
IBM Ultrium 3 LTO 80 MB/s
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD 80 MB/s
N/A
Ultra-3 SCSI(Ultra-160) LVD
160MB/s
N/A
Ultra-3 SCSI(Ultra-160) LVD
160MB/s
HP Ultrium 1 LTO
HP Ultrium 2 LTO
HP Ultrium 3 LTO
15 MB/s
30 MB/s
80 MB/s
Ultra-2 SCSI
HVD Fast 40
Ultra-2 SCSI LVD
80 MB/s, SE 40MB/s
N/A
Ultra-3 SCSI Ultra-160 LVD
160MB/s
N/A
Ultra-4 SCSI Ultra-320 LVD
160MB/s
1. The maximum burst speed of data transfer for the HVD interface is at 40 MB/s
2. The maximum burst speed of data transfer for the LVD interface varies depending upon the type of
SCSI interface.
3. Certance is owned by Quantum Corporation.
96053
Revision L
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
Installing the Drives
If you are installing an SDLT 600 drive, make sure that Field Bill 102181 was
installed. The field bill replaces the internal fan finger guard with a perforated
steel plate to comply with emissions standards.
Use the information in the following paragraphs if you ordered a library that did not have
the drives already installed, or if you want to add more drives to your library.
Note: Because the drive is part of the drive tray assembly, you will actually be installing
the assembly.
You should always add drives by starting at the empty slot nearest the top and working
downward. The drive numbers are assigned from top (0) to bottom (3). By adding drives
in this order, the client software will correctly reflect the drives previously installed.
If you already have some drives installed, observe these precautions before beginning:
CAUTION:
Possible data loss or system problem: If you must disconnect the
external SCSI cables, make sure that you stop all processes attached to
this system.
•
If the drives are daisy-chained, stop all data processing on the channel to which the
drives are connected before disconnecting the drives.
•
Make sure that there is no activity on the SCSI bus before disconnecting the external
SCSI cables. Stop all processes on the client-server computer.
•
•
Make sure that all signals are terminated at each end of the SCSI bus.
Do not mix single-ended and differential terminators.
WARNING:
Lifting hazard: Depending upon the drive type, each drive and tray
weighs between 5.0 kg (11 lb) and 5.8 kg (12.7 lb). Make sure you follow
ADVERTENCIA:
Riesgo al levantar: En función del tipo de unidad, cada unidad y bandeja
pesa entre 5,0 kg (11 lb) y 5,8 kg (12,7 lb). Asegúrese de seguir las
instrucciones de la sección “Técnicas de levantamiento de objetos” en
1-26
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
CAUTION:
Possible component damage: Do not use a screwdriver for the drive door latch knob
or drive tray latch.
1. At the rear of the library, turn the drive door latch knob to your left to open the drive door.
1. Knob
CAUTION:
Load/unload problems: The drive tray latch must be fully loosened (disengaged)
before you slide the tray into the slot. If the latch arm contacts part of the library
frame as it is being tightened, it cannot be rotated to its fully locked position, and the
tray will not be firmly locked into the drive slot. This can cause alignment problems
and the camera can have problems reading the target.
2. Holding the drive tray assembly as shown in the figure below, turn the drive tray latch knob all the
way to your right so that it is in its fully disengaged position.
1. Knob
2. Range
3. Latch arm (shown disengaged)
96053
Revision L
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Installation Procedure
3. Slide the drive tray assembly into the desired slot.
CAUTION:
Possible component damage: Do not use a screwdriver to tighten the drive tray latch
knob.
4. Turn the knob all the way to the right to engage the latch and clamp it firmly into the frame.
5. Pull back on the tray to make sure the tray is securely latched. It should not move.
6. Connect the drive SCSI connector, P903, to the drive.
7. Connect the drive power cable, P904A/B, to the library.
8. Connect the serial interface connector, P6A/B, to the library.
1. P903
2. P904A/B
3. P6A/B
CAUTION:
Possible equipment damage: Make sure the SCSI cable does not block the fan before
you close the drive door.
Possible cable damage: Make sure you move the SCSI cable out of the way before
you close the drive door.
Possible component damage: Do not use a screwdriver to tighten the drive door
latch knob.
9. Close the drive door and secure it by turning the drive door latch knob to your right.
10. Refer to your user’s guide to configure the drives.
1-28
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering-on the Library and Drives
■ Powering-on the Library and Drives
To power-on the library and drives:
CAUTION:
Possible equipment damage: Make sure the power-on/off switch is set to
“O” before performing Step 1.
1. Close and lock the front door.
2. Attach the power cable to the power receptacle at the rear of the library and plug the
cable into an electrical outlet.
3. Press the power switch to the “|” position.
The operator status display shows the Init in Progress:message. When
initialization is complete, the status display shows the state of the library.
4. Use the library operator panel to configure the library and drives.
Note: Refer to the user’s guide for any field values that you do not understand.
Note: You must fully configure the library before you configure the tape
management software.
■ Recording the Configuration Information
Record your library configuration in the following table. Then make a copy of the table
and give it to the customer. The customer will refer to it when making a service call or
ordering features and upgrades.
96053
Revision L
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording the Configuration Information
Table 1-6. L40 Tape Library Configuration Information
Library Serial Number _____________________________
Library Warranty Number __________________________
Version: 20 cells ❑ 32 cells ❑ 40 cells ❑
Library Code Version ____________
Library SCSI ID _________
Number of Drives Installed ______
Drive 0 Serial Number _____________________________
Drive 0 Warranty Number __________________________
Drive 0 SCSI ID _________
Drive Type ______________________
On Bus ❑ Off Bus ❑
Drive 1 Serial Number _____________________________
Drive 1 Warranty Number __________________________
Drive 1 SCSI ID _________
Drive Type ______________________
On Bus ❑ Off Bus ❑
Drive 2 Serial Number _____________________________
Drive 2 Warranty Number __________________________
Drive 2 SCSI ID _________
Drive Type ______________________
On Bus ❑ Off Bus ❑
Drive 3 Serial Number _____________________________
Drive 3 Warranty Number __________________________
Drive 3 SCSI ID _________
Drive Type ______________________
On Bus ❑ Off Bus ❑
Fast Load: Off ❑ On ❑
Auto Clean: Off ❑ On ❑
Network: Library Name ______________________________________
IP Address ________________
Gateway ________________
Subnet Mask ________________
Network
Hardware Monitor______________________________________
Warning Temperature ________________
Shutdown Temperature ________________
1-30
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations, Specifications, and
Cables
2
This chapter identifies library components, drive label locations, specifications, and
external cable part numbers.
■ Locations
Use the following figures to become familiar with the library components and drive label
locations.
Figure 2-1. Front View of Components (L201_061)
96053
Revision L
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations
Figure 2-1. Front View of Components (L201_061)
1. Operator panel (including status display)
2. Cartridge access port (CAP)
4. Viewing window
5. Door lock
3. Elastomer feet for desktop version
Figure 2-2. Rear View of Components (L201_062)
23
26
27
24
28
25
29
0
1
PWR
LNK/ACT FIBER
CHANNEL
HVD/SCSI
SERIAL
ETHERNET
20
7
22
12
5
19
6
13
14
15
8
9
16
21
4
3
10
11
1
2
18
17
L201_575
2-2
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations
Figure 2-2. Rear View of Components (Continued) (L201_062)
1. Power-on/off switches
2. Power receptacles
15. Personality module connector
16. Library serial number and agency label
3. Standard power supply
4. Redundant power supply
17. Library warranty identification number
18. Dual power label
5. Library RESET button—use a wooden pencil
(never a screwdriver or other electrically-
conductive item) to press this button
6. Ethernet/Web port
7. Library LVD/HVD SCSI ports
8. SCSI port for Drive 0 (See note.)
9. SCSI port for Drive 1 (See note.)
10. SCSI port for Drive 2 (See note.)
11. SCSI port for Drive 3 (See note.)
12. Fibre Channel router card SCSI ports
13. Reserved for development engineers, not for
customer use
19. Fibre Channel router card (optional)
20. Fibre Channel router card port
21. Electronics module
22. Fibre Channel router card CSE serial port
23. External Fibre Channel Router (optional)
24. External Fibre Channel Router Power
Receptacle
25. External Fibre Channel Router Power Switch
26. External Fibre Channel Router Serial Port
27. External Fibre Channel Router Ethernet port
28. External Fibre Channel Router Fibre Channel
port
14. Customer Services Engineering (CSE) serial
port
29. External Fibre Channel Router SCSI Bus ports
Note: The top drive that is installed is Drive 0. If all four drives are installed, the top drive is Drive 0
and the bottom is Drive 3. If drives are installed only in the two middle slots, the top drive
installed is Drive 0 and the drive beneath it is Drive 1.
96053
Revision L
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations
Figure 2-3. Internal View of Components (L201_063)
1. Hand Assembly
2. Drive 3
7. Fibre Channel router card (optional)
8. Cartridge
3. Drive 2
4. Drive 1
5. Drive 0
9. Columns 0 through 3, with 3 on far right
10. Cleaning cartridge cell
11. CAP cells (two)
6. Library vision calibration label; the master
target is below it
2-4
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations
Figure 2-4. Robotic Components (L201_255)
1. Z motor
4. Z carriage
2. Hand assembly
3. Z shafts
5. Theta motor
Figure 2-5. DLT Drive Label Locations (L201_164)
1. FRU serial number
2. Warranty ID number
3. CEI serial number
96053
Revision L
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Figure 2-6. Ultrium Drive Label Locations (L201_165)
1. CEI serial number
2. FRU serial number
3. Warranty ID number
■ Specifications
The following pages provide library, drive, and cartridge specifications.
For more specific drive and cartridge information, refer to the vendor Web site or
documentation.
Library Environment
The following table lists the library environment specifications.
Table 2-1. Library Environment Specifications
Item
Measurements
Storage
Operating
Transporting
Temperature
Humidity
+10 to +40ºC
+50 to +104ºF
+10 to +40ºC
+50 to +104ºF
-40 to +60ºC
-40 to +140ºF
20 to 80%
10 to 95%
10 to 95%
2-6
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Table 2-1. Library Environment Specifications (Continued)
Item
Measurements
Storage
Operating
Transporting
Wet bulb (maximum,
noncondensing)
+29.2ºC
+84.5ºF
+35ºC
+95ºF
+35ºC
+95ºF
Altitude
-76 to 3,048 m (-250 to 10,000 ft)
Library Power
The following table lists the power specifications for the library without drives.
Table 2-2. Library Power Specifications
Input voltage
100–240 VAC, single phase
50/60 Hz
Frequency
Maximum library power consumption
Maximum heat output
Voltage-amperes
1.42 A at 120 V or 0.75 A at 240 V
614 Btu/hr
180 VA
Drive and Cartridge Weights
The following table lists the drive and cartridge weights. Refer to the drive publication
and vendor Web site for updated information.
Table 2-3. Drive and Cartridge Weights
Item
Weight
DLT drive and tray
5.4 kg (12 lb)
2.72 kg (6 lb)
3.17 kg (7 lb)
223 g (7.9 oz)
5.0 kg (11 lb)
5.8 kg (12.7 lb)
5.5 kg (12 lb)
220 g (7.8 oz)
DLT1 drive and tray
Super DLT drive and tray
DLT/DLT1/Super DLT cartridge
HP Ultrium LTO drive and tray
IBM Ultrium LTO drive and tray
Seagate Ultrium LTO drive and tray
Ultrium 100 GB cartridge
96053
Revision L
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Drive Power
The following table lists the drive power specifications. Refer to the drive publication and
vendor Web site for updated information.
Table 2-4. Drive Power Specifications
Drive
Volt-
Amperes
Current
Heat output
130 Btu/hr
256 Btu/hr
222 Btu/hr
198 Btu/hr
157 Btu/hr
236 Btu/hr
160 Btu/hr
DLT1
38 VA
72 VA
65 VA
58 VA
46 VA
69 VA
0.30 A at 120 VAC
0.16 A at 240 VAC
DLT 7000E
DLT 8000
0.59 A at 120 VAC
0.30 A at 240 VAC
0.53 A at 120 VAC
0.27 A at 240 VAC
Super DLT
HP Ultrium LTO
IBM Ultrium LTO
0.47 A at 120 VAC
0.24 A at 240 VAC
0.37 A at 120 VAC
0.19 A at 240 VAC
0.56 A at 120 VAC
0.29 A at 240 VAC
Seagate Ultrium LTO 47 VA
0.38 A at 120 VAC
0.20 A at 240 VAC
2-8
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Figure 2-7. L40 Desktop Version Dimensions and Weight (L201_346)
1. 455 mm (17.90 in.) height with feet; feet are
16 mm (0.625 in.).
2. 490 mm (19.30 in.) width
3. 724 mm (28.50 in.) depth without external
cables
4. 102 mm (4.0 in.) dedicated fan exhaust
clearance area (shaded area allows for cable
and cooling clearances)
Weight (library only) 44.45 kg (98 lb)
96053
Revision L
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Figure 2-8. L40 Rack Version Dimensions and Weight (L201_343)
1. 442 mm (17.39 in.) height
6. 102 mm (4.0 in.) dedicated fan exhaust clearance
2. 483 mm (19.0 in.) width of front with flange
3. 728 mm (28.65 in.) depth with fan, without cables
4. 448 mm (17.65 in.) width
5. 702 mm (27.65 in.) depth without fan, without
cables
area (shaded area allows for cable and cooling
clearances)
7. 702 mm (27.65 in.) depth without fan, without
cables
Weight (library only) 44.45 kg (98 lb)
2-10
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Cord Numbers and Receptacles
■ Power Cord Numbers and Receptacles
Power cord part numbers for the library are listed in the table below. All cords are 3 m
(9.8 ft).
The receptacle type is listed. Refer to your vendor catalog for the part number.
Table 2-5. Country-specific Power Cords
Input Voltage
Country
U.S./Canada
Japan
Part Number
10187019
10083243
10083244
10083248
Receptacle Type
5-15R
100 to 127 VAC
JIS C8303
AS 3112
200 to 240 VAC
Australia
Denmark
DEMKO107/
10-1973
Europe
10187018
10187022
Schuko
IEC309
Europe (Continental)
See Note 2.
Italy
10083245
10083657
10083636
10083246
10083247
10187020
CEI 23-16/V11
KSC 8305
BS546
Korea
South Africa
Switzerland
United Kingdom
U.S./Canada
CEE 7
BS 1363
6-15R
Note: This is a harmonic no plug cord for Belgium, Denmark, Finland, France,
Germany, Holland, Norway, Sweden, and Switzerland.
Table 2-6. Non-country-specific Power Cords
Input Voltage
100 to 127 VAC
250 VAC
Description
Part Number
SJT IEC320 14AWG, 3 m, receptacle 5-15
10187061
SJT 16 AWG L6-15P, C13, 2.5 m, receptacle L6-15P 10187024
250 VAC
18, 3, SVT, 1mm, M/SH FRT
3, F, IEC320 harmonized (see Note)
International power cord pigtail
10187055
10187047
10083735
100 to 240 VAC
Note: The cord has a plug on one end that attaches to the library and bare wires on the other.
Buy the correct end to match your normal wall outlet and attach it to the cord.
96053
Revision L
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
External Cables
■ External Cables
of power cords for specific countries.
Note: The SCSI universal cables listed below are intended for use with LVD
application. The cables used to meet these requirements are inherently more
costly and should be used only as required for HVD.
Table 2-7. External Cables
Description
Part Number
10083312
10083639
10187005
10187008
10187009
10187010
10187011
10187012
10187013
10410823
313645101
313645201
313645302
313708802
313708902
410828902
Cable assembly, 68 MD, 20 m (65.6 ft) (HVD use only)
Cordset, SJT, 16AWG, L6-15P
SCSI universal, 68MD-68MD, 500 mm (19.7 in.), LVD
SCSI universal, 68MD-68MD, 3 m (9.8 ft)
SCSI universal, 68MD-68MD, 5 m (16.4 ft)
SCSI universal, 68MD-68MD, 10 m (32.8 ft)
SCSI universal, 68MD-68HD, 3 m (9.8 ft)
SCSI universal, 68MD-68VHD, 5 m (16.4 ft)
SCSI universal, 68MD-68VHD, 10 m (32.8 ft)
Fibre Channel router RJ45 to DB9 adapter
Cable assembly, flat shield, SCSI 68, 300 mm (11.8 in.), HVD
Cable assembly, flat shield, SCSI 68, 600 mm (23.6 in.), HVD
Cable assembly, flat shield, SCSI 68, 1 m (39.37 in.), universal
Cable assembly, flat shield, SCSI 68, 300 mm (11.8 in.), LVD
Cable assembly, flat shield, SCSI 68, 600 mm (23.6 in.) LVD
Fibre Channel router serial cable with two RJ45 connectors; RJ45
Connector and Consultive Committee on International Telephony and
Telegraph (CCITT) cable, 6.1 m (20 ft)
2-12
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP
A
This appendix provides the implementation of the Simple Network Management
Protocol (SNMP).
■ Overview
Sun StorageTek’s L-series libraries support Version 1 of the simple network management
protocol (SNMPv1). SNMP is an application layer protocol that performs network
management operations over an Ethernet connection using a User Datagram Protocol
(UDP/IP). Library microcode 2.11 or higher supports SNMP.
SNMP allows systems administrators to query the library for configuration, operation,
and statistical information. SNMP also allows the library to inform the systems
administrator of potential problems.
Systems administrators and network managers use SNMP to monitor and receive status
from the library, such as:
•
•
•
•
•
•
Operational state of the library (such as microcode level, serial number, online)
Status of the cartridge access port (such as open, closed, number of cells)
Library elements (number of hands, columns, panels, cells, CAPs)
Number of storage cells and media types stored in the library
Number and types of drives installed in the library
Many other variables defined in the database
Figure A-1 on page A-2 illustrates a simple network block diagram that identifies the
locations of the SNMP software application, DNS servers, and Library Admin. This
figure also identifies the IP addresses, shows a map of DNS names (library names), and
other components involved in that configuration (such as operator panel, Ethernet
connections, location of the Management Information Base (MIB), and the LLC card.
96053
Revision L
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Figure A-1. SNMP and DNS Network Block Diagram Example (L201_523)
1. Ethernet connection (ENET) for the library.
2. To configure the library to support DNS.
Note: You must enter the Domain Name Service (DNS) configuration only if your Simplified Network
Management Protocol (SNMP) agent is set to trap named recipients; if SNMP is set for numbered
recipients (by using IP addresses), no entries are required.
3. An example of a table that matches IP addresses to selected DNS names.
4. SNMP software application that implements the role of manager. Some applications include:
HP Open View
IBM NetView
Sun Microsystems SunNet Manager
5. The MIB is stored on the LLC card. To view the contents of the MIB database, enter:
http://IP.Address/Lseries.mib or http://library_name/Lseries.mib
6. Library Admin. is an optional feature for the library. It provides the GUI-based monitoring system and is
separate from the SNMP application. Library Admin provides an easy and convenient way to configure
the library SNMP agent using a network configuration panel or screen. Library Admin also provides
other beneficial functions and display screens for the library.
A-2
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP Terms
■ SNMP Terms
SNMP uses a manager/agent structure, a database, and a small set of commands to
exchange information. SNMP terms include:
•
•
•
•
Agent–A module that resides in a managed device. The agent is responsible for
responding to requests from the manager and for sending traps to a recipient that
inform the systems administrator of potential problems.
Community String–Applications use community strings for access control. The
manager includes the community string in its SNMP messages to an agent. The agent
consequently can accept or reject the operation.
Managed device–A device that hosts the services of an SNMP agent that provides
monitored information and controlled operations using SNMP. L-Series libraries are
managed devices.
Management Information Base (MIB)–A collection of information stored in a
database that contains configuration and statistical information for a managed
device. For L-Series libraries, a copy of the MIB is loaded with microcode and stored
information about the MIB.
•
Manager–A thing that provides the communication link between the systems
administrator and the managed devices on the network. A manager station or server
allows the systems administrator to get information about the device through the
MIB and to receive traps from an agent.
•
•
Recipient–A location on a manager where the SNMP agent sends traps. This
location is defined by the combination of either the IP address or DNS name and the
port number. The default recipient port number is 162.
Trap–A message that reports a problem, error, or a significant event that occurred
within the device.
96053
Revision L
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP Commands
■ SNMP Commands
SNMPv1 offers a limited number of commands that follow a simple request/response
exchange to communicate between the manager and the agent.
The manager issues request such as:
•
•
•
Get–A request for information of a specific variable.
GetNext–A request for the next specific variable.
Set–A request to change the value of a specific variable.
The agent responds with:
•
•
Get-Response–A response to the manager’s Get and GetNext commands.
Trap–An asynchronous message to the recipient about an error or event.
Refer to the SNMP software documentation for additional information.
■ Access Control
Because community strings provide a weak form of access control in SNMPv1, Sun
StorageTek’s embedded agent will not rely on the so called “private” community string in
order to accept changes to the library’s configuration. Access control and authorization
for Set operations is performed by using an administrative password. Consequently, Sun
StorageTek’s embedded agent uses only one community string for both Get and Set
operations.
■ Management Information Base
The MIB is a viewable document that contains descriptions about the characteristics for a
managed device. These characteristics are the functional elements for that device which
can be monitored using SNMP software.
To access and view the contents of the MIB using a Web browser, enter the IP Address
or library name and Lseries.mib. For example: http://IP.Address/Lseries.mib or http://
library_name/Lseries.mib.
Note: Sun StorageTek’s L-series libraries implement only MIB extensions defined in
the LSERIES-TAPE-LIBRARY-MIB under the private (4) section as shown in
Figure A-2 on page A-5 shows the MIB hierarchy as a tree structure where the
L-series MIB is located.
A-4
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Management Information Base
Figure A-2. Management Information Base Hierarchy (L201_522))
MIB Title = LSERIES-TAPE-LIBRARY-MIB
Object Name = iso.identified-organization.dod.internet.private.enterprise.storagetek.products.lsereis
Equivalent Object Descriptor = 1.3.6.1.4.1.1211.1.12
96053
Revision L
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
■ Configuration
Three ways to configure the library to support SNMP are:
•
•
•
Library Admin, an optional feature for the library, but it is not required to support
SNMP.
The CLI port (command line interface)
The SNMP software application—you can also use any SNMP application to change
some of the agent’s settings. You must be MIB-aware and refer to the L-series.mib for
specific information.
Figure A-3. CLI Help and Help SNMP Commands
cli> help
help [command]
diag
help on a specific command
execute diagnostics
download
fsc
network
snmp
time
password
download new image to prom
manipulate fault symptom codes
manipulate network information
manipulate SNMP configuration
view/modify library date & time
reset/modify library admin password
cli> help snmp
snmp view
display SNMP Agent settings
snmp community [string] set Community String/IP address
snmp [enable|disable] enable of disable SNMP Agent
snmp port [port number] set Agent Listening Port Number
(Valid: 161, 1024-65535)
snmp grace [number]
set Write Grace Period Number
( 1-5 minutes )
snmp reset
set SNMP Agent configuration parameters
to default values
snmp list
snmp add
display SNMP Trap Recipient List
add a member to the SNMP Trap Recipient List by
answering individual prompts for values.
snmp add [ipaddr|name] add a member to the SNMP Trap Recipient List using
some default values
snmp add [ipaddr|name] [host port number]
add a member to the SNMP Trap Recipient List
using some default values
snmp delete [[ipaddr|name] [host port number]] | all
delete all or a selected member of the SNMP
Trap Recipient List
Where valid [host port number] values: (162, 1024-65535)
cli> _
A-6
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting SNMP
Table A-1. SNMP Default Settings
Setting
Default
Description
161
Port number
Valid port IDs are 161, and 1024 to 65535
Agent community string. When set to public,
requests coming from any community string
will be accepted.
Community String public
Once you enter the password, you have 1 to
5 minutes to Set any values for the agent.
5 minutes
Grace Period
This list supports up to 12 recipients with
no duplicate entries.
Trap Recipient List Empty
Disabled
SNMP (agent)
Enabled or Disabled
■ Starting SNMP
To start SNMP for the library, you must:
1. Configure the library:
a. Enable the agent
b. Add recipients to the trap list (if needed)
c. Make any optional changes to the default settings.
2. Re-IPL the library for the changes to take effect.
96053
Revision L
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting SNMP
This page intentionally left blank.
A-8
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
AC power supply
advertencia
CEI serial number
attaching
configuration
B
connecting external cables
buttons
C
cables
cables de fibra óptica
D
DES
cables, external connections
cartridges
procedimientos a seguir durante tareas de
mantenimiento o servicio técnico, xxx
desktop installation
dimensions
caution
96053
Revision L
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
drives
H
HVD
I
E
ID label
instalación
ESD
installation
F
fiber-optic cables
Fibre Channel router
FRU serial number
interfaces
G
K
grounding
Index-2
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
L
library
LVD
M
MIB
montaje en bastidor
N
locations
O
P
part numbers
peligro
personality module
96053
Revision L
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
power
precaución
precauciones
S
safety
SCSI
precautions
seguridad
preparing
puesta a tierra
Q
SNMP
R
rack installation
rack-mounting
reset button
specifications
Index-4
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
W
warning
warranty ID number
T
weights
U
worksheets
V
96053
Revision L
Index-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index-6
Revision L
96053
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sun Microsystems, Inc. 4150 Network Circle, Santa Clara, CA 95054 USA Phone 1-650-960-1300 or 1-800-555-9SUN Web sun.com
ARGENTINA: 5411-4317-5636 • AUSTRALIA: 1-800-550-786 • AUSTRIA: 43-1-601-26-0 • BALKANS: 301-6188-111 • BELGIUM: 32 2-704 89 83 • BRAZIL: 55-11-51872100 • BRUNEI: 65-216-8333 • CANADA: 1-800-422-8020 (GENERAL); 416-964-2001 (LEARNING MANAGEMENT SYSTEM SALES,TORONTO) • CHILE: 562-372-4500 • COLOMBIA: 571-629-2323
CZECH REPUBLIC: 420 2 33009311 • DENMARK: 45 4556 5040 • EGYPT: 00 202 570 9442 • FINLAND: 358-9-525-561 • FRANCE: 33-1-41-33-17-17 • GERMANY: 49-89-460-08-2788 • GREECE: 30-01-6188101 • HONG KONG: 852-2877-7077 • HUNGARY: 361-202-4415 • INDIA: 91-80-229-8989 • INDONESIA: 65-216-8333 • IRELAND: 353-1-668-4377
ISRAEL: 972-9-9710500 • ITALY: 39-02-9259511 • JAPAN: 81-3-5779-1820 • KOREA: 82-2-3453-6602 • MALAYSIA: 603-2116-1887 • MIDDLE EAST: 00 9714 3366333 • MEXICO: 525-261-0344 • NETHERLANDS: 31-33-4515200 • NEW ZEALAND: 0800-786-338 • NORTH WEST AFRICA: 00 9714 3366333 • NORWAY: FROM NORWAY: 47-22023950, TO NORWAY:
47-23369650 • PAKISTAN: 00-9714-3366333 • PEOPLE'S REPUBLIC OF CHINA: 8610-6803-5588 • PHILIPPINES: 632-885-7867 • POLAND: 48-22-8747848 • PORTUGAL: 351-21-413-4000 • RUSSIA: 7-095-935-8411 • SAUDI ARABIA: 00 9714 3366333 • SINGAPORE: 65-216-8300 • SOUTH AFRICA: 27-11-256-6300 • SPAIN: 34-902-210-412 • SRI LANKA:
65-2168333 • SWEDEN: 46-8-631 22 00 • SWITZERLAND: 41-1-908-90-50 (GERMAN) 41-22-999-0444 (FRENCH) • TAIWAN: 886-2-25185735 • THAILAND: 662-344-6855 • TURKEY: 90 212 335 22 00 • UNITED KINGDOM: 44-1276-416-520 • UNITED STATES: 1-800-422-8020 • VENEZUELA: 582-905-3800 • VIETNAM: 65-216-8333 • WORLDWIDE
HEADQUARTERS: 1-650-960-1300
THE NETWORK IS THE COMPUTER ©2006 Sun Microsystems, Inc. All rights reserved. Sun, Sun Microsystems, and the Sun logo are trademarks or registered trademarks of Sun Microsystems, Inc. in the
United States and other countries.
SUN™
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Air Conditioner AF S125NX User Manual
Sharper Image MP3 Docking Station EC P115 User Manual
Sony Camera Accessories APK WA User Manual
Sony CD Player SCD XE597 User Manual
Sony Speaker SRS A205 User Manual
Sony Stereo Receiver STR DA2ES User Manual
Southwestern Bell Telephone FM2552PX User Manual
Southwing Headphones SH305 SH310 SH315 User Manual
Sterling Heat Pump GG 105 User Manual
Sunbeam Hot Beverage Maker KE2200 User Manual