Operating Instructions
Single Conveyor Unit
SSE-5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Sterling Material Processing retains all rights to change the information in these operating
instructions at any time without notice.
We assume no liability for any errors or direct or indirect damage resulting in context with these
operating instructions.
Copying, translation or publication in any form except for personal use of purchaser requires
approval from Sterling Material Processing.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note that our address and phone information has changed.
Please reference this page for updated contact information.
These manuals are obsolete and are provided only for their technical information, data and capacities.
Portions of these manuals detailing procedures or precautions in the operation, inspection, maintenance
and repair of the products may be inadequate, inaccurate, and/or incomplete and shouldn’t be relied
upon. Please contact the ACS Group for more current information about these manuals and their
warnings and precautions.
Parts and Service Department
The ACS Customer Service Group will provide your company with genuine OEM quality parts manufactured to engineering
design specifications, which will maximize your equipment’s performance and efficiency. To assist in expediting your phone
or fax order, please have the model and serial number of your unit when you contact us. A customer replacement parts list
is included in this manual for your convenience. ACS welcomes inquiries on all your parts needs and is dedicated to
providing excellent customer service.
For immediate assistance, please contact:
•
North, Central and South America, 8am – 5pm CST +1 (800) 483-3919 for drying, conveying, heating and cooling
and automation. For size reduction: +1 (800) 229-2919.
North America, emergencies after 5pm CST (847) 439-5855
North America email: [email protected]
•
•
•
Mexico, Central & South America
Email: [email protected]
Europe, Middle East & Africa +48 22 390 9720
Email: [email protected]
India +91 21 35329112
Email: [email protected]
•
Asia/Australia +86 512 8717 1919
Email: [email protected]
Sales and Contracting Department
Our products are sold by a worldwide network of independent sales representatives. Contact our Sales Department for the
name of the sales representative nearest you.
Let us install your system. The Contract Department offers any or all of these services: project planning; system packages
including drawings; equipment, labor, and construction materials; and union or non-union installations.
For assistance with your sales or system contracting needs please Call:
(
)
North, Central and South America +1 262 641-8600 or +1 (847) 273-7700 Monday–Friday, 8am–5pm CST
Europe/Middle East/Africa +48 22 390 9720
India +91 21 35329112
Asia/Australia +86 512 8717 1919
Facilities:
ACS offers facilities around the world to service you no matter where you are located. For more information, please visit us at
Asia/Australia:
India
United States:
ACS India
ACS Suzhou
Gat No. 191/1, Sandbhor Complex
Mhalunge, Chakan, Tal Khed,
Dist. Pune 410501, India
Phone: +91 21 35329112
Fax: + 91 20 40147576
ACS Schaumburg – Corporate Offices
1100 E. Woodfield Road
Suite 588
109 Xingpu Road SIP
Suzhou, China 215126
Phone: + 86 8717 1919
Fax: +86 512 8717 1916
Schaumburg, IL 60173
Phone: + 1 847 273 7700
Fax: + 1 847 273 7804
Europe/Middle East/Africa
ACS New Berlin – Manufacturing Faci
2900 S. 160th Street
ACS Warsaw
Ul. Działkowa 115
02-234 Warszawa
Phone: + 48 22 390 9720
Fax: +48 22 390 9724
New Berlin, WI 53151
Phone : +1 262 641 8600
Fax: + 1 262 641 8653
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Table of contents
1. 1. General instructions..........................................................................................1-1
1.1. Warnings and symbols.......................................................................................1-2
1.2. Explanations and information ............................................................................1-3
1.3. Legal basis ........................................................................................................1-3
1.4. Fields of applications.........................................................................................1-3
1.5. Notes on usage ..................................................................................................1-3
2. Safety instructions................................................................................................2-1
2.1. For your safety ..................................................................................................2-2
2.1.1.
2.1.2.
2.1.3.
2.1.4.
General .................................................................................................2-2
Assembly..............................................................................................2-3
Operation..............................................................................................2-4
Maintenance..........................................................................................2-4
2.2. For the operating safety of the equipment ..........................................................2-5
3. Putting into operation ...........................................................................................3-1
3.1. Checking the pipe system ..................................................................................3-2
3.2. Adjusting the suction pipes................................................................................3-3
3.3. Setting the controller .........................................................................................3-4
3.4. Initial conveying operations...............................................................................3-5
3.5. Switching off the unit ........................................................................................3-5
4. Error and error correction ........................................................................................6
5. Maintenance............................................................................................................8
5.1. Maintenance intervals......................................................................................... 10
5.2. Servicing the conveyor ....................................................................................... 10
5.2.1.
5.2.2.
5.2.3.
Changing the sealing ring of the outlet flap ............................................ 11
Adjusting the flap switch........................................................................ 12
Cleaning the unit.................................................................................... 13
5.3. Replacing carbon brushes at turbine...................... Error! Bookmark not defined.
6. Functional description ........................................................................................... 15
6.1. General............................................................................................................... 16
6.2. Controller........................................................................................................... 17
7. Transport, Assembly and Storage .......................................................................... 19
7.1. Transport and Packing........................................................................................ 20
7.2. Assembly ........................................................................................................... 20
7.3. Storage ............................................................................................................... 20
8. Assembly instructions ........................................................................................... 21
8.1. Assembly ........................................................................................................... 22
8.2. Mounting on the processing machine.................................................................. 24
8.3. Mounting onto a machine hopper........................................................................ 24
8.4. Mounting onto mixing hoppers with lateral inlet................................................. 25
8.5. Mounting onto dosing station DT 30................................................................... 25
8.6. Material feed ...................................................................................................... 26
8.7. Mounting the suction pipe MV ........................................................................... 26
8.8. Pipework ............................................................................................................ 27
8.9. Electrical connection .......................................................................................... 27
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.9.1.
8.9.2.
8.9.3.
Installation of the “flap switch” signal line............................................. 28
Installation of the signal line of the SKW (optional)............................... 28
Installation of the alarm indicating device (optional).............................. 29
8.10. Compressed-air supply (only SSE-2 with active cleaning) ............................... 30
8.11. Installing the accessories................................................................................... 30
9. Technical data ....................................................................................................... 31
10.
Spare parts list................................................................................................... 34
10.1. SSE-2, 230 V, 50 Hz ........................................................................................ 36
10.2. SSE-2, 110 V, 60 Hz .......................................... Error! Bookmark not defined.
10.3. SSE-2, 230 V, 50 Hz with active cleaning........... Error! Bookmark not defined.
10.4. SSE-2, 110 V, 60 Hz with active cleaning........... Error! Bookmark not defined.
10.5. Accessories....................................................................................................... 37
11.
12.
Accessories........................................................................................................ 38
Electrical manual............................................................................................... 39
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
1. General instructions
These instructions apply to all persons within the range of action
of the equipment.
These operating instructions are to be used by all persons
assigned activities connected with the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
1.1. Warnings and symbols
The following warnings and symbols are used in these operating instructions:
This symbol indicates danger to life! Fatal or serious injury is
possible if the corresponding instructions, regulations or
warnings are not observed.
L
This symbol indicates that serious injury is possible if the
corresponding instructions, regulations or warnings are not
observed.
F
This symbol indicates that extensive damage to equipment is
possible if the corresponding instructions, regulations or
warnings are not observed.
&
This symbol indicates information important for becoming
familiar with the equipment, i.e. technical correlations.
$
This symbol indicates that a technical term is explained at this
point.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
1.2. Explanations and information
Various terms and designations are used in these operating instructions to ensure clarity.
Therefore please note that the terms used in the text stand for the corresponding explanations
listed below.
•
Equipment: ”Equipment” can mean an individual unit, a machine or an installation.
•
Operating personnel: The ”operating personnel” are persons operating the equipment on their
own responsibility or according to instructions.
•
•
•
•
Operator: The ”operator” of the equipment (production manager, foreman, etc.) is the person
responsible for all production sequences. The operator instructs the operating personnel of
what is to be done.
Operating instructions: The ”operating instructions” describe the interaction of the equipment,
production sequences or methods. The operating instructions must be compiled by the
operator of the equipment.
Equipment foreman: When several operating personnel work on one machine, the
”equipment foreman” coordinates the sequences. The equipment foreman must be appointed
by the operator.
Trained personnel: ”Trained personnel” are persons who, due to their training, are authorized
to carry out the required work.
1.3. Legal basis
See “Manufacturer’s Certificate” resp. “Certificate of Conformity”.
1.4. Fields of applications
Sterling single conveying units are designed for use in facilities in which require independent
machine conveying systems. The single conveying units have been developed for conveying
thermoplastic granules. A typical area of application is for processing machines and drying
hoppers with throughputs of up to 500 kg/h (1090 lbs/hr).
1.5. Notes on usage
•
Experienced operators can begin directly with the chapter on “Start-up” if the unit has been
properly installed.
•
If the unit has not been installed yet, observe the instructions in the chapters “Transport,
Assembly and Storage” and “Assembly Instructions”.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
2. Safety instructions
These safety instructions apply to all persons within the range of
action of the equipment.
Please inform all persons within the range of action of the
equipment of the direct and indirect hazards connected with the
equipment.
These operating instructions are to be used by all persons
assigned activities connected with the equipment.
Knowledge of the English language is prerequisite.
Ensure in each case that the operating personnel are familiar with
the operating instructions and the function of the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
2.1. For your safety
2.1.1. General
The operating personnel of this equipment must be at least 16 years old.
Please read these operating instructions carefully before taking into operation for the first time.
Contact us should questions arise. This avoids injury and damage to equipment!
These operating instructions must be kept available at all times at the place of operation of the
equipment. Improper operation results in danger of accidents!
Please note that, for reasons of clarity, not all conceivable cases regarding operation or
maintenance of the equipment can be covered in these operating instructions.
Please observe all safety instructions and warnings on the equipment. This avoids injury and
damage to equipment!
All work on the equipment is to be carried out by persons whose qualifications are specified in the
pertaining chapters of the operating instructions. Improper operation results in danger of
accidents!
The proper working clothes are to be worn during any work on the equipment. This avoids injury!
The local regulations and requirements pertaining to this equipment must be observed.
Disconnect electrical components from the mains supply before work is carried out on these
components Caution: Danger to life through electrical shock!
Compile detailed operating instructions based on these Operating instructions for the sequence of
procedures to be carried out on this equipment. Improper operation results in danger of
accidents!
Please note that sound levels exceeding 85 db(A) may in the long term damage your health. Use
the appropriate ear muffs. This avoids impairment of hearing!
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
2.1.2. Assembly
Compare the connected loads with those of the mains supply. Danger of injury through electrical
shock!
When using lifting gear, please observe the pertaining regulations. Caution: Danger of accidents!
Do not modify, add other equipment or change the design of the equipment without the approval
of the manufacturer. Caution: Danger of accidents!
Attachments not supplied by Sterling must be manufactured in accordance with safety regulation
EN 294. Danger of accidents!
The equipment may only be operated when all the associated components are properly
connected up and in accordance with the relevant regulations. This avoids injury and damage to
equipment!
Operate the device only if all its components are grounded. Danger: accident through electrical
shock!
Solid particles and dust must be separated before entry to the vacuum generator. This avoids
damage to equipment!
If PVC hoses are used for conveying, they must be grounded. This avoids injury and damage to
equipment!
An acoustic cover should be installed when vacuum generators are located in work rooms. This
avoids impairment of hearing!
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
2.1.3. Operation
Appoint an equipment foreman to be responsible for the equipment.
Ensure that the operating personnel are provided detailed instruction in the operation of the
equipment. Improper operation results in danger of accidents!
When the main switch is switched off for reasons pertaining to safety, it must be secured against
unauthorized activation. Caution: Danger of accidents!
Repair work may be carried out by trained personnel only. Caution: Danger of accidents!
Never operate the equipment when partially dismantled! Danger! Limbs may be caught in
machinery! Electric shock!
In case of malfunction, shut down the equipment immediately. Have malfunctions corrected
immediately. Danger of accidents!
The equipment is intended only for conveying granulated plastics and regrinds. Any other or
additional use is contrary to specifications.
This equipment is not suitable for food processing.
The safety instructions of the connected machines must be followed.
Explosive gases and mixtures of gas and air must not be conveyed. Danger of explosion! Avoids
injury or damage to equipment!
2.1.4. Maintenance
Before starting maintenance work, appoint a supervisor.
Inform the responsible personnel before maintenance work on the system is started. Caution:
Danger of accidents!
Disconnect the equipment from mains supply before starting maintenance procedures to ensure
that it cannot be switched on unintentionally. Caution: Danger of accidents!
All pipes, hoses and screwed connections should be checked regularly for leaks and damage.
Any faults which arise should be corrected immediately. Danger of accidents!
Depressurise all compressed air piping before starting maintenance work. Danger of accidents!
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
2.2. For the operating safety of the equipment
Never change settings if the consequences are not precisely known.
Use only original Sterling spare parts.
Please observe the maintenance schedule.
Keep record of all maintenance and repair work.
Please note that electronic components may be damaged by static discharge.
Check all electrical connections for proper fit before the equipment is taken into operation for the
first time and at regular intervals.
Please ensure that the permitted operation temperature lies between 0 °C and +45 °C
(32 to +113 °F).
Please ensure that the permitted storage temperature lies between -25 °C and +55 °C
(-13 to +131 °F).
Note down all data which you have entered into the control system.
Please ensure that all plugs are correctly plugged in.
The operating instructions of the connected machines must be followed.
Operate the device only if all its components are grounded.
Never adjust sensors without exact knowledge of their function.
Please note that a compressed air supply is required for the operation of the unit (only SSE-2 with
active cleaning, optional).
Never set a higher operating pressure than 6 bar for the hopper loaders (system overpressure).
Align the suction tubes correctly.
The unit should be installed in such a way that the outlet flap oscillates at right angles to the
moving direction of the equipment.
The load-bearing capacity of the machine flange should be adhered to.
Please observe that a level indicator is required when conveying from granulators.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
3. Putting into operation
This chapter is intended for operating personnel.
Prerequisite for this chapter is general knowledge of the
operation of conveying systems.
Also prerequisite for this chapter is that the functional description
has been read and understood.
Ensure in each case that the operating personnel are sufficiently
informed.
F
Make sure the plastic stopper has been removed from the
material inlet nozzle.
Make sure the adhesive tape has been removed from the exit flap.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
3.1. Checking the pipe system
Remove the flexible hose from the connected material takeup.
Close the open end of the hose with your hand.
Connect the unit to mains supply by the device plug.
If the turbine is operating, your hand must feel the suction within few seconds.
If you don’t feel the vacuum it means that the pipe system is not tight.
Check the pipe system and seal any untight points you may have identified.
Reconnect the conveying hose.
Disconnect the unit from mains supply by the device plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
3.2. Adjusting the suction pipes
The suction pipes have to be adjusted exactly to ensure troublefree operation.
1. Set the suction pipes to their home position.
&
At home position the inner pipe of the suction pipe protrudes
about 120-160 mm (4.75" - 6.25") from the outer pipe at the top
end.
2. Start a conveying operation.
Connect the unit to mains supply by the device plug.
3. Observe the flexible hose at the suction pipe.
The flexible hose must not show any pulsating movement
4. Observe the flexible hose at the separator.
The conveying hose must only move during in-feed.
If the conditions (points 3 + 4) are not met:
Pull the inner pipe further out of the outer pipe until there is no more jerky conveyance.
If the conditions (points 3 + 4) are met:
Push the inner pipe slowly into the outer pipe until pulsating of the flexible hose or shock
conveyance occurs.
Now pull the inner pipe slightly back again until the hose stop pulsating.
Select a setting between the two pipes to ensure that enough air can flow into the material pipe.
Once you have reached a satisfactory conveying result turn the wing screw at the suction pipe
tight.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
3.3. Setting the controller
F
The filling capacity of the hopper loader may not exceed the
material inlet.
&
The setting is independent of the conveying line and the material
to be conveyed.
It is only possible to set the conveying time/line clear time when
the unit is not conveying any material.
Setting the conveying time
Press the “arrow key”.
&
The conveying time which was last selected appears in the
display.
1-99 seconds may be set for the conveying time.
The conveying capacity is too highlow (the separator is overcrowded):
Reduce the conveying time.
The conveying capacity is too low:
Increase the conveying time.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Setting the line clear time
Press the “change-over” key and
then the “arrow key”.
&
The line clear time which was last selected appears in the display.
0-99 seconds may be set for the line clear time.
F
3.4. Initial conveying operations
If no line clear valve has been installed enter “0".
Metal shavings may be inside the pipe from cutting down pipes into lengths. These are pulled
during the first conveying process and collected in the separator.
F
3.5. Switching off the unit
This material should not be used again.
Disconnect the unit from mains supply by the device plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
4. Error and error correction
This chapter is intended for the operating personnel of the
equipment.
Prerequisite for this chapter is general knowledge of the
operation of conveying systems
The “Start-up” description must have been read and understood.
Ensure in each case that the operating personnel are sufficiently
informed.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
If a disturbance occurs in the unit, an alarm message will be issued (option, only if the alarm
indicating device has been activated).
&
An “E” appears in the display and an error number.
The alarm indicating device (signal siren, horn) reacts.
F
The control system can only restart operation when the
malfunction has been corrected.
Press the “acknowledgement key”.
&
The cause of the malfunction will not be corrected by pressing
the “acknowledgement key”.
The following error messages can be displayed:
“E1"
The alarm message “E1" is displayed when no material has been conveyed during 3 consecutive
conveying cycles.
Check that sufficient material is being conveyed.
Check that the flap switch is set correctly.
F
When the malfunction has been corrected press the key.
“E2"
If the control system becomes too hot during operation (>70°C, 158°F) the “E2" alarm message is
displayed and the unit is switched off.
Ensure that the control system is sufficient cooled.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
5. Maintenance
This chapter is intended for persons with skills in electrical and
mechanical areas due to their training, experience and received
instructions.
Personnel using the instructions in this chapter must be
instructed of the regulations for the prevention of accidents, the
operating conditions and safety regulations and their
implementation.
Ensure in each case that the personnel are informed.
For maintenance work taking place at heights of over approx. 6
feet, use only ladders or similar equipment and working platforms
intended for this purpose. At greater heights, the proper
equipment for protection against falling must be worn.
Use only suitable lifting gear which is in proper working order and
load suspension devices with sufficient carrying capacity. Do not
stand or work under suspended loads!
Ensure that the electric motors/switch cabinets are sufficiently
protected against moisture.
Use only suitable workshop equipment.
Before starting maintenance work, appoint a supervisor.
Inform the responsible personnel before maintenance work on the
system is started.
Never operate the equipment when partially dismantled.
All maintenance and repair work not described in this chapter may
only be carried out by Sterling service personnel or authorized
personnel (appointed by Sterling).
L
Disconnect the equipment from mains supply before starting
maintenance procedures to ensure that it cannot be switched on
unintentionally.
Depressurize all system sections of the equipment before
carrying out any repair work.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
F
Please observe the maintenance intervals.
Before starting maintenance work, clean the equipment of oil, fuel
or lubricants.
Ensure that materials and incidentals required for operation as
well as spare parts are disposed of properly and in an
environmentally sound manner.
Use only original Sterling spare parts.
Keep record of all maintenance and repair procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
5.1. Maintenance intervals
Daily:
Check warning signs on equipment for good legibility and completeness
Clean the filter: Use compressed air to blow through the filter (according
to the accumulation of dust)
Monthly:
Check function of the device plug
Every 6 months:
Check all electrical and mechanical connections for tight fit
Replace the filter (according to the accumulation of dust)
Annually:
Replace outlet valve sealing.
Adjust valve switch
F
The given maintenance intervals are average values.
Check whether in your individual case the maintenance intervals
must be shortened.
5.2. Servicing the conveyor
Disconnect the unit from mains supply by the device plug.
Depressurize all system sections of the equipment
Disassembly the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
5.2.1. Changing the sealing ring of the outlet flap
Remove the connecting plug “flap switch” (A)
Remove the tension ring (B) and the sealing ring (C).
Remove the upper part of the hopper loader (D) from the lower part (E).
Draw the old sealing ring (F) off the nozzle of the material outlet.
Install the new sealing ring (F)
F
Observe the direction of installation (G).
Install the upper part of the hopper loader (D) on the lower part (E).
Install the sealing ring (C) and the tension ring (B) on the hopper loader.
Connect the connecting plug “flap switch” (A) to the connection housing of the hopper.
Install the unit.
&
Order number sealing ring “material outlet”: ID 23098
Figure 0: Installation sealing ring
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
5.2.2. Adjusting the flap switch
Remove the connecting plug “flap switch”
from the connection housing of the hopper.
Connect an ohmmeter to PINS 2 and 3 of
the connecting plug “flap switch”.
Release the nuts (A) of the flap switch (B)
until the support can be displaced.
Open the outlet flap (C) so far that the front
tip of the outlet flap is approx. 30 mm (1.2")
away from the sealing surface.
Displace the flap switch (B) until the
contact of the magnet switch is closed.
Tighten the nuts (A) of the flap switch.
Check the adjustment:
In case of free hanging outlet flap (empty
hopper loader) the contact of the magnet
switch must be closed.
Figure 1: Outlet flap
If the outlet flap cannot be properly adjusted, replace the flap switch or the outlet flap with
magnet.
Install the hopper.
&
Order numbers
switch with plug:
outlet flap with magnet:
ID 28839
ID 23093
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
5.2.3. Cleaning the unit
Open the toggle-type fasteners (A).
Fold the hopper lid with turbine upwards.
Remove the filter (B).
Clean the filter by means of compressed-air.
Clean the hopper loader by means of a vacuum cleaner.
Mount the filter (B). Pay attention for proper fit.
Loosen the lid protection by lifting the lid and close the hopper lid.
Close the toggle-type fasteners (A).
&
Order number
filter: ID 34179
Figure 2: SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Open the toggle-type fasteners (A) and the flap
(B) of the hopper loader.
Check the filter cloth (C) and the wire cloth (D)
for material residue. Clean the filter by means of
compressed air.
Close the flap (B) and the toggle-type fasteners
(A) on the flap of the hopper loader.
Install the unit.
&
Order numbers
Figure 3: SSE-2
Filter cloth:
Wire cloth:
ID 28626
ID 23091
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
6. Functional description
This functional description is intended for all operating personnel
of the equipment.
Prerequisite for this functional description is general knowledge
of conveying systems.
Ensure in each case that the operating personnel are sufficiently
informed.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
6.1. General
The single conveyor unit functions according to the principle of
suction conveyance. A high-performance turbine, mounted
permanently on the device, provides for the vacuum that is
required to convey the material into the separator.
In the separator the material is separated from air. After the
conveying time is finished the turbine is switched off and the
material emptied into the material intermediate hopper. If the filling
level remains below the outlet flap of the single conveyor unit, a
starting pulse is triggered and sent to the controller.
The filter will be blowed off using compressed air. Then the
conveyance is restarted. This process repeats so often until the
material intermediate hopper is filled. Afterwards the conveyance
is stopped until a new starting pulse is triggered and sent to the
controller.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
6.2. Controller
The control system is mounted on the separator lid.
The setting for the conveying time and the line clear time are made via the keys (A1: “change-
over” key, A2: “arrow key”) on the front of the control system. The values which have been set
will be displayed on the display (B). The values which have been set are maintained after the
machine has been shut off.
3 LEDs indicate the respective modes of operation: cleaning (C), conveying (D), line clearing (E).
&
The conveying time can be set from 1 to 99 seconds.
The line clear time can be set from 0 to 99 seconds.
The clearing time consists of 2 seconds.
The emptying time consists of 8 seconds.
When the unit is switched on all LEDs blink and the software
version is displayed.
C
E
B
A1
A2
Figure 4: Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
If a material clearing valve has been installed residues of flowing material will be cleaned from the
conveying line during the line clear time.
If a disturbance occurs in the unit, an alarm message will be issued (only if the alarm indicating
device has been activated).
&
An “E” appears in the display and an error number.
The alarm indicating device (signal siren, horn) reacts.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
7. Transport, Assembly and Storage
This chapter is intended for all operating personnel of the
equipment.
Personnel using these instructions must be instructed in the
regulations for the prevention of accidents, the operating
conditions and safety regulations and their implementation.
Ensure in each case that the operating personnel are sufficiently
informed.
Please inform all persons within the range of action of the
equipment of the direct and indirect hazards connected with the
equipment.
Please observe all safety regulations for the operation of lifting
equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
7.1. Transport and Packing
Please ensure adequate carrying capacity of the lifting
equipment.
The equipment pass a rigorous operating test in the factory and are packed carefully to avoid
transport damage.
Please check packing on delivery for transport damage.
The inlet and discharge flanges are sealed with plugs, so that no dirt can enter during transport.
Plugs must be removed before assembly.
Packing materials should be disposed of according to environmental laws or reused.
Only use for transport of the equipment a suitable lifting device (e. g. a fork lift truck or a
workshop crane).
Transport must be shock-proofed and free from vibrations.
7.2. Assembly
Please ensure adequate carrying capacity of the lifting
equipment.
Check the carrying capacity of the point of installation,
particularly if installed on a platform.
The place selected for installation should be as free of vibrations
as possible.
The main switch must be freely accessible.
Ground the equipment against electrostatic charging.
7.3. Storage
The control system may only be stored at temperatures from -25 to +55°C (-13 to +131 °F).
Between delivery and machine commissioning the equipment should be stored in a dry, dust-free
and vibration-free room.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8. Assembly instructions
These installation instructions are intended for persons with
skills in electrical and mechanical areas due to their training,
experience and received instructions.
Personnel using these installation instructions must be instructed
in the regulations for the prevention of accidents, the operating
conditions and safety regulations and their implementation.
Ensure in each case that the personnel are informed.
The installation instructions provided in the corresponding
operating instructions apply for all connected equipment.
Please observe all safety regulations for the operation of lifting
gear.
All installation work must be carried out with the equipment
disconnected from electrical power an compressed air supply.
L
For installation work taking place at heights of over approx. 6
feet, use only ladders or similar equipment and working platforms
intended for this purpose. At greater heights, the proper
equipment for protection against falling must be worn.
Use only suitable lifting gear which is in proper working order and
load suspension devices with sufficient carrying capacity. Do not
stand or work under suspended loads!
Use only suitable workshop equipment.
F
Install the equipment such that all parts are easily accessible; this
facilitates maintenance and repair work.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.1. Assembly
The single conveyor unit is insensitive to shocks and can be
mounted directly onto the processing machine, on a machine
hopper, a drying hopper or a dosing and blending unit.
The equipment is delivered as a complete assembly.
Remove the plastic stopper (A) from the material inlet nozzle.
Open the flap (B) and remove the adhesive tape from the exit
flap.
A
B
F
The controller must be freely accessible.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Mounting on fixed machine throats or intermediate containers is done by means of strap
retainers.
Please check during assembly that the admissible bearing loads are not exceeded.
Mount the conveyor in such a way that the outlet flap swings in a right angle to the direction of
machine movement.
Please check that all connecting points are tight to ensure that the conveying performance is not
impaired.
Figure 5: Assembly
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.2. Mounting on the processing machine
A material hopper VT 2,3/70 / VT 2,8/70 is required:
Mount the material hopper onto the flange of the
processing machine.
Mount the unit onto the material hopper.
Figure 6: VT 2,3/70 / VT2,8/70
Observe the bearing capacity of the machine flange.
F
8.3. Mounting onto a machine hopper
A welding flange EF 190 or an assembly flange MF 253 is required:
L
Please observe all safety regulations for the operation of welding
equipments.
Always wear a safety goggle.
Weld the welding flange into the machine hopper lid.
Mount the unit onto the flange.
Or
Figure 6: EF 253
Mount the assembly flange.
Mount the unit onto the flange.
Figure 6: MF 253
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.4. Mounting onto mixing hoppers with lateral inlet
A material hopper VT 2,3/70/VT2,8/70 is required:
Mount the material hopper onto the swan-neck of the
mixing hopper.
Mount the unit onto the intermediate hopper.
Figure 7: VT 2,3/70/2,8/70
F
8.5. Mounting onto dosing station DT 30
Observe the bearing capacity of the machine flange.
An adapter piece AD 1/5 is required:
Mount the dosing hopper directly onto the dosing container
of the dosing station DT 30.
Mount the unit onto the dosing hopper.
Figure 8: AD 1/5
F
Observe the bearing capacity of the machine flange.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.6. Material feed
Suction pipes type MV may be tilted by approx. 45 degrees in either direction to the vertical.
Additional fastening is not required.
When conveying from the bottom of storage containers (silos), a suction box with 1-3 suction
pipes is required.
The connection of the suction pipes must be carried out with a piece of flexible line to provide
sufficient movement.
Please observe that the length of the hose should not exceed 3 meters (10 feet). Push the free
pipe end into the flexible line to a depth of approx. 4-5 cm (1.5" - 2"). Connect both parts by
means of a hose clamp.
8.7. Mounting the suction pipe MV
The suction pipe consists of an inner pipe (A) and an outer pipe (B) which can be offset against
each other.
Connect the inner pipe with the straight end to a flexible hose:
Push the free pipe end into the flexible line to a depth of approx. 4-5 cm (1.5" - 2").
Connect both parts by means of a hose clamp.
Please observe that the length of the hose should not exceed 3 meters (10 feet).
Please check that the outer pipe is not covered as it provides for unhindered access of ambient
air.
F
When conveying from silos, material hoppers and storage
containers, a suction box with 1-3 suction pipes is required.
Figure 8: MV
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.8. Pipework
If PVC hoses are used for conveying, they must be grounded: draw out the copper lead on both
ends of the hose and jam it between hose and tube. For fastening, use threaded clamps.
8.9. Electrical connection
The regulations of the local Electricity Board must be observed.
Before connection to the electricity supply, it should be ensured
that the supply voltage and the power frequency are in
accordance with the data on the name plate of the machine.
The electrical connection may only be carried out by Sterling
service staff or trained personnel authorised by Sterling.
It is not permitted for other persons to undertake the electrical
connection.
The main switch must be freely accessible.
Ground the equipment against electrostatic charging.
The operating voltage is 230 V/50 Hz.
Special voltages on request.
The connected load is approx. 1200 W.
The equipment is connected to mains supply by a device plug.
Separate fuse protection of the wall socket is required (max. 16 A).
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.9.1. Installation of the “flap switch” signal line
Insert the appliance plug of the “flap switch” signal line into the “flap switch” connector (A) on the
lower side of the controller.
Figure 9: Lower side of the controller
8.9.2. Installation of the signal line of the SKW (optional)
&
Observe the connecting diagram.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.9.3. Installation of the alarm indicating device (optional)
This work must be carried out by qualified personnel only.
Disconnect the unit from mains supply by the device plug before
you begin with works on the controller. Danger to life!
The connection is potential-free and rated for 5 A.
&
Observe the connecting diagram.
An additional alarm indicating device (e.g. horn, signal light) can
be connected.
You need an “acknowledgement key” for 24 V (e.g. by Rafi
Company).
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
8.10. Compressed-air supply
For operating the cleaning device, a compressed-air supply is necessary.
Check compressed-air piping for correct installation and assembly.
Check fittings, length and quality of the hose connections for agreement with requirements.
The operating pressure is 5-6 bar (72-87 PSI) (system overpressure).
Check the compressed-air supplied by the plant’s supply network.
Adjust compressed-air pressure to 5-6 bar (72-87 PSI) (system overpressure).
Connect the unit to the plant’s supply network by means of a hose.
L
F
Depressurize compressed-air supply lines which must be opened.
Compressed air must be dewatered, dustfree and oilfree.
Install a maintenance unit if required.
Adjust pressure to a max. value of 6 bar (87 PSI) (system
overpressure).
8.11. Installing the accessories
F
See chapter “Accessories”.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
9. Technical data
These instructions apply to all persons within the range of action
of the equipment.
These operating instructions are to be used by all persons
assigned activities connected with the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
SSE 5/BL
Basic Version
• Integrated control with:
- LED-display
- indication of the respective modes of operation
- adjustable conveying time
- material clearing valve output
- two component valve output
- automatic shut-down with lack of material
- level sensor input when in use with granulators (automatic clearing prevents overcharging
of the granulator
• Integrated brush-less vacuum pump
• Well suited for continuousoperation with up to 100 % duty cycle
• Integrated textile filter with pneumatic cleaning
• Parts coming in contact with material are made of stainless steel
• Simple mounting to dosing and blending units due to compact and weight saving design
Optional Features
• Extension modules
Performance
• Conveying capacity max. up to 500 kg/hr (1090 lbs/hr) at 100 % operating time
• Hopper loader capacity: ca. 5 l (.0.17 cu. ft.)
• Connected load: 230 V, AC, N, PE, 50/60 Hz, 0,8 kW; 110 V, AC, N, 60 Hz
• Material temperature max. 80 °C (176°F)
• Noise level max. approx. 82 db(A)
• Weight approx. 16 kg (35 lbs.)
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Dimension Sheet
Dimensions and data without obligations. Specifications may be subject to alterations.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
10. Spare parts list
This spare parts list is intended to be used only by trained
personnel.
Other persons are not permitted to modify or repair the
equipment.
&
Wear Code:
A = Wearing part, fast used up
B = Wearing part
C = Spare part, storekeeping for 1 year
D = Spare part, storekeeping for 2 years
E = Spare part, storekeeping for more than 2 years
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
SSE-f/BL, 230 V, 50 Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
10.1. SSE-5/BL, 230 V, 50 Hz
Pos.
1
Order no.
S38217
82995
83375
84914
83098
34179
28420
85533
26451
28839
23093
85477
85471
93358
23098
28626
23091
28625
Designation
Turbine lid with turbine, complete
Turbine 119 154-01
Solenoid valve
Pneumatic hose
Controller
Wear Code
2
3
4
Filter
B
C
Sealing ring
Tension ring
Lock
Flap switch with plug
Outlet flap with magnet
Nut
Screw
Disc
Sealing ring
Filter cloth
Wire cloth
5
6
7
8
9
10
B
D
E
D
Sealing
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
10.2. Accessories
F
Please observe the operating manuals in chapter 11.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
11. Accessories
o _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
o _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
o _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
12. Electrical manual
This electrical manual is intended to be used only by Sterling
service personnel and trained personnel authorized by Sterling.
Other persons are not permitted to modify or repair the
equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
SSE 5 BL
Download from Www.Somanuals.com. All Manuals Search And Download.
|